Miller Electric Soft Start 1 User manual

Miller Electric Soft Start 1 User manual
Issued Dec. 2014 • Index No. AD/4.9
Dynasty 280 Series
®
Quick
Specs
Industrial Applications
Processes
Precision Fabrication
Heavy Fabrication
Pipe and Tube Fabrication
Aerospace
Aluminum Ship Repair
Anodized Aluminum Fabrication
AC/DC TIG (GTAW)
Pulsed TIG (GTAW-P)
Stick (SMAW)
Air Carbon Arc (CAC-A)
TIG/Stick Welding
Power Source
Input Power 208 – 575 V, 3- or 1-Phase Power
Amperage Range 1 – 280 A (DC)
2 – 280 A (AC)
Rated Output 200 A at 28 V, 60% Duty Cycle
Net Weight 52 lb. (23.6 kg)
Update and expand. Front panel
memory card data port provides
the ability to easily update software
and expand product features.
AC TIG Features
Balance control provides adjustable
oxide removal which is essential
for creating the highest quality
aluminum welds. DX models provide
extended ranges.
Frequency controls the width of the
arc cone and can improve directional
control of the arc.
Visit MillerWelds.com/TIGSoftware
for the latest software updates
and expansions.
Pro-Set™ eliminates the guesswork
when setting weld parameters.
Use Pro-Set when you want the
speed, convenience and confidence
of preset controls. Simply select
the feature and adjust until
Pro-Set appears on the display.
AC Waveforms
Sleep timer conserves electricity.
This programmable feature will power
down the machine if it sits idle for a
specific time.
Dynasty 280 DX
Dynasty 280
Allows for any input voltage hookup
(208 – 575 V) with no manual linking,
providing convenience in any job setting.
Ideal solution for dirty or unreliable power.
Cooler Power Supply (CPS). An
integrated 120-volt dedicated-use
receptacle to power the Coolmate™ 1.3.
The power switch on the Dynasty also
activates the receptacle to help prevent
torch failure. Available on select models,
see page 6.
Meter calibration allows digital meters to be calibrated
for certification.
™
Wind Tunnel Technology protects internal electrical
components from airborne contaminates, extending the
product life.
Fan-On-Demand™ power source cooling system operates
only when needed, reducing noise, energy use and the
amount of contaminants pulled though the machine.
Blue Lightning™ high-frequency (HF)
arc starter for non-contact arc initiation.
Provides more consistent arc starts and
greater reliability compared to traditional
HF arc starters.
Advanced squarewave,
fast freezing puddle, deep
penetration and fast travel speeds.
Soft squarewave for a soft
buttery arc with maximum
puddle control and good wetting action.
Sine wave for customers that
like a traditional arc. Quiet with
good wetting.
Triangular wave reduces the
heat input and is good on thin
aluminum. Fast travel speeds.
DC TIG Features
Exceptionally smooth and precise arc
for welding exotic materials.
AC/DC Stick Features
DIG control allows the arc characteristics to be changed for specific
applications and electrodes. Lower
the DIG setting for smooth running
electrodes like E7018 and increase
the DIG setting for stiffer, more
penetrating electrodes like E6010.
Hot Start™ adaptive control provides
positive arc starts without sticking.
AC frequency control adds stability for
smoother welds when AC Stick welding.
Stick-Stuck detects if the electrode is
stuck to the part and turns the welding
output off to safely and easily remove
the electrode. Menu selectable.
Power source is warranted for 3 years, parts and labor.
Miller Electric Mfg. Co.
Equipment Sales US and Canada
An ITW Company
1635 West Spencer Street
P.O. Box 1079
Appleton, WI 54912-1079 USA
Phone: 866-931-9730
FAX: 800-637-2315
International Phone: 920-735-4554
International FAX: 920-735-4125
MillerWelds.com
Specifications (Subject to change without notice.)
Welding
Amperage
Range
Rated Output
3-phase
2–280 A (AC)
1–280 A (DC)
235 A at 19.4 V,
60% duty cycle
19
17
10
9
7
7.0
6.7
1-phase
2–280 A (AC)
1–280 A (DC)
235 A at 19.4 V,
60% duty cycle
33
30
17
15
12
6.9
6.8
3-phase
5–280 A
200 A at 28 V,
60% duty cycle
22
20
11
10
8
8.2
7.9
1-phase
5–280 A
180 A at 27.2 V,
60% duty cycle*
34
31
17
15
12
7.1
7.0
Welding
Mode
Input
Power
TIG
(GTAW)
Stick
(SMAW)
Max. OpenCircuit
Voltage
Amps Input at Rated Load Output, 50/60 Hz
208 V 230 V 400 V 460 V 575 V KVA KW
60 VDC
(11 VDC**)
Dimensions
H: 13.6 in. (346 mm)
W: 8.6 in. (219 mm)
D: 22.5 in. (569 mm)
Net
Weight
52 lb.
(23.6 kg)
55 lb.
(25 kg)
with CPS
*Refer to owner’s manual for 208 V output ratings and duty cycle. **Low OCV sense voltage for Stick and Lift-Arc ™ TIG.
IP23 rating — This equipment is designed for outdoor use. It may be stored, but is not intended to be used outside during precipitation unless sheltered.
Operating temperature range is 14 to 104° F (-10 to 40° C). Storage temperature range is -22 to 149° F (-30 to 65° C). Portions of the preceding text are contained in
EN 60974-1: “Welding power sources for arc welding equipment.”
Certified by Canadian Standards Association to both the Canadian and U.S. Standards.
All CE models conform to the applicable parts of the IEC 60974 series of standards.
Performance Data
Input
Power
TIG (GTAW)
Duty Cycle
Stick (SMAW)
Duty Cycle
AC TIG Material
Thickness Range
DC TIG Material
Thickness Range
Stick Electrode
Maximum Diameter
Carbon Arc Gouging
(CAC-A) Maximum
Generator
Requirement
3-phase
280 A, 25%
235 A, 60%
200 A, 100%
280 A, 15%
200 A, 60%
160 A, 100%
.012 – 3/8 in.
.004 – 3/8 in.
6010: 1/4 in.
7018: 7/32 in.
7024: 3/16 in.
3/16 in.
12.5 kW
1-phase*
280 A, 25%
235 A, 60%
200 A, 100%
280 A, 10%
180 A, 60%
160 A, 100%
*Refer to owner’s manual for 208 V output ratings and duty cycle.
Coolmate 1.3 Cooler
™
• Dynasty® models with CPS turn Coolmate 1.3
on and off
• Power indicator light
• Fluid level sight window
• Rustproof polyethylene-molded coolant tank
and filler spout
• 1/4-HP motor is thermally protected to guard
against overheating
2
• Efficient fin and tube heat exchanger
• Factory-set pressure relief valve (55 PSI)
maintains consistent pressure during operation
• Filter and coolant filling spout are conveniently
located
• Brass-body, positive displacement rotary vane
pump provides consistent coolant flow and
pressure rating with long pump-life expectancy
Input Power
Maximum Current Draw
Maximum Cooling Capacity
Rated Cooling Capacity
Tank Capacity
Dimensions
Net Weight
115 VAC,
60 Hz
4.7 A (60 Hz)
3400 W (11,600 BTU/hr.)
3.8 qt./min. (1.7 L/min.)
1330 W (4540 BTU/hr.)
1.1 qt./min. (1 L/min.)
1.3 gal. (4.9 L)
H: 11.25 in. (286 mm)
W: 10.375 in. (264 mm)
D: 24 in. (610 mm)
43 lb.
(20 kg)
Weldcraft W-280 (WP-280) TIG Torch
™
• Two-piece torch head and exclusive Super Cool™
Technology provides additional surface area to
increase cooling efficiency and capacity
• Torch body includes an anti-rotation feature
and multi-position locking to prevent handle
movement during welding and improve
operator control
• Secure mechanical fittings and connections
minimize leakage
Cooling Method
AC Rating
DC Rating
Consumables
Electrode Range
Cable
Water-cooled
195 A, 100% duty cycle
280 A, 100% duty cycle
13N
.020–1/8 in. (0.5–3.2 mm)
Three-piece
TIG Upgrade Chart
Why Upgrade?
Syncrowave 250 UPGRADE Dynasty 280 UPGRADE Dynasty 280 DX
Dynasty 280 Benefits
Thickness Capacity
.015 – 3/8 in. Aluminum
.012 – 3/8 in. Steel
.012 – 3/8 in. Aluminum
.004 – 3/8 in. Steel
The Dynasty 280 has a lower bottom end, and can weld
thinner metals.
200 A, 60%
235 A, 60%
Weld longer at higher amperages. At 200 A the
Dynasty 280 can weld continuously.
Continuous HF
Start Only HF
HF on Start Only limits HF interference issues during
the weld.
Digital and Dial %
All Digital
Precise adjustments can be made with all-digital controls
for greater quality control and repeatability.
Confusion on Where
to Set the Controls?
Trial and Error
Pro-Set™ eliminates the guesswork when
setting weld parameters.
Select the feature and adjust until Pro-Set appears in
display. Pro-Set is available for Balance, Frequency, Pulse
and DIG parameters.
AC Frequency Control
(Aluminum TIG)
Fixed at 60 Hz
Variable 70 – 150 Hz
Variable 20 – 400 Hz
Higher frequencies provide better arc control and faster
travel speeds.
AC Balance Control
(Aluminum TIG)
45 – 68%
Electrode Negative
60 – 80%
Electrode Negative
50 – 99%
Electrode Negative
Greater electrode negative helps to produce welds with
less etching for more aesthetic looking welds.
AC Waveforms
(Aluminum TIG)
Soft Squarewave
Soft Squarewave
Advanced Squarewave
Soft Squarewave
Sine Wave
Triangular Wave
Duty Cycle
High Frequency
Arc Starting
Precision Controls
Weld Aluminum with
Pointed Tungsten
(Aluminum TIG)
Portability
Power Flexibility
Line Draw at
200 Amps
Advanced Squarewave = Travel faster
Soft Squarewave = Maximum puddle control
Sine Wave = Traditional characteristics
Triangular Wave = Reduced heat input
Extended Frequency and Balance controls permit welding
aluminum with pointed tungsten. The benefits are reduced
heat input into your part, smaller weld beads, better
starting, more control of the arc and faster travel speeds.
378 lb. (172 kg)
Crane or Cart
52 lb. (23.6 kg)
Carry or Cart
Manual Link, 208/230/460 V
1-Phase Only
Auto-Line™, 208 – 575 V
1-Phase or 3-Phase
Auto-Line allows the unit to operate on any voltage.
1- or 3-phase. Even generators!
77 A, 230 V, 1-Phase
25 A, 230 V, 1-Phase
15 A, 230 V, 3-Phase
Line requirement to operate is much less. Smaller
electrical service needed, smaller breaker/fuses and
power cord.
Easier to move because of size and weight. Don’t have to
wait for a crane operator.
3
Dynasty 280 Control Panel
®
7
1
8
2
9
3
4
10
5
11
12
6
13
1. Standby Switch
7. Memory Card Port
2. Voltmeter Display
8. Activity Indicator
3. Ammeter Display
9. Encoder Control
4. Output Contactor “On” Indicator
10. Menu Ranges
5. AC TIG Process Menu Parameters
Amperage
2 – 280 A**
Balance*
60 – 80%
Frequency*
70 – 150 Hz
Postflow
Auto/Off – 50 seconds
11. DC TIG Process Menu Parameters
Amperage
1 – 280 A**
Pulse*
Off – 250 PPS
Postflow
Auto/Off – 50 seconds
6. AC Stick Process Menu Parameters
Amperage
5 – 280 A
DIG*
Off – 100%
12. DC Stick Process Menu Parameters
Amperage
5 – 280 A
DIG*
Off – 100%
13. Process Selector
*Pro-Set parameter selectable. **Amperage range is tungsten size dependent.
User Menu (Hold Menu button three seconds.)
Tech Menu (Hold Menu button five seconds.)
AC TIG
1. Start = HF/Lift Arc
2. Tungsten Size = .020 –1/8 in. or .05 – 3.2 mm
3. Remote Trigger = STD/HOLD/OUTPUT ON
1. Arc Time
AC Stick
1. Hot Start = ON/OFF
2. Remote Trigger = OUTPUT ON/STD
DC TIG
1. Start = Lift Arc/HF
2. Tungsten Size = .020 –1/8 in. or .05 – 3.2 mm
3. Remote Trigger = STD/HOLD/OUTPUT ON
DC Stick
1. Hot Start = ON/OFF
2. Remote Trigger = OUTPUT ON/STD
4
0.0 – 9999 hours
0.0 – 59 minutes
0 – 999,999 cycles
Resettable
2. Error Log = Error event recorder
3. Sleep Timer = 1/5/10/15/30/45MIN/1HR
4. Stick Stuc = OFF/ON
5. OCV = LOW/NORM
6. Cooler Power = AUTO/OFF (only on Dynasty models with CPS)
7. Machine Reset
8. Software Number
9. Serial Number
Dynasty 280 DX Control Panel
®
1
8
9
2
10
3
11
12
4
5
6
7
13
14
1. Standby Switch
10. Encoder Control
2. Voltmeter Display
11. Amperage Button
3. Ammeter Display
4. Polarity
AC/DC
5. Process/
Arc Starting
TIG: HF Impulse, Lift-Arc
STICK: Adaptive Hot Start
6. Output Control
Standard Remote,
2T Trigger Hold,
Output ON
7. Pulser Control
Pulses per Second* DC: 0.1 – 500 PPS
AC: 0.1 – 500 PPS
Peak Time*
5 – 95%
Background Amps* 5 – 95%
8. Memory Card Port
9. Activity Indicator
12. AC Waveshape
Balance*
Frequency*
50 – 99% EN
20 – 400 Hz
13. Gas/DIG
Preflow
Postflow
DIG*
0.0 – 25.0 seconds
Auto/Off – 50 seconds
Off –100%
14. Sequencer Control
Initial Amps
AC: 2 – 280 A
DC: 1– 280 A
Initial Slope
0.0 – 25.0 seconds
Weld Time
0.0 – 999 seconds
Final Slope
0.0 – 25.0 seconds
Final Amps
AC: 2 – 280 A
DC: 1– 280 A
*Pro-Set parameter selectable.
User Menu (Press Gas and Amperage buttons.)
Tech Menu (Hold Gas and Amperage buttons five seconds.)
1. Tungsten Size = .020 –1/8 in./GEN or .05 – 3.2 mm
2. Remote Trigger = 3T/4T/4TL/4TLE
3. Wave Form = SOFT/ADVS/SINE/TRI
4. Stick Hot Start = ON/OFF
1. Arc Time
0.0 – 9999 hours
0.0 – 59 minutes
0 – 999,999 cycles
Resettable
2. Error Log = Error event recorder
3. Sleep Timer = 1/5/10/15/30/45MIN/1HR
4. Stick Stuc = OFF/ON
5. OCV = LOW/NORM
6. Cooler Power = AUTO/OFF (only on Dynasty models with CPS)
7. Weld Timers = OFF/ON
8. Locks = OFF/1– 4
9. Meter Display
10. External Pulse Control = OFF/ON
11. Machine Reset
12. Software Number
13. Serial Number
5
Dynasty 280 Models/Packages
®
Build an
Air-Cooled
Package
Select desired
stock number
for each step.
#907 550
Dynasty shown.
#195 055
kit shown.
Step #1 • Select Dynasty
Dynasty 280
Dynasty 280 with CPS
Dynasty 280 DX
Dynasty 280 DX with CPS
#907 550
#907 537
#907 551
#907 514
Step #2 • Select Contractor Kit
Note: For models without the Cooler Power
Supply (CPS), the Coolmate 1.3 must
be powered through an external 120-volt
facility power.
Dynasty comes with adjustable shoulder strap, 8-ft. power cord (no plug),
quick reference guide and two 50-mm Dinse-style connectors.
Build a
Water-Cooled
Package
Select desired
stock number
for each step.
Foot Control Contractor Kit
Fingertip Control Contractor Kit
See page 7 for kit contents.
#907 537 002
Dynasty 280
TIGRunner® shown
with four bottles
of #043 810
Low-Conductivity
Coolant.
#194 744 remote shown.
Step #1 • Select Dynasty TIGRunner® and Coolant
#300 990 kit shown.
Step #2 • Select Remote Control
Dynasty 280 (with CPS) TIGRunner
#907 537 002
Dynasty 280 DX (with CPS) TIGRunner #907 514 001
&
Low-Conductivity Coolant
#043 810
(Must be ordered in quantities of four.)
Wireless Foot
RFCS-14 HD Foot
RCC-14 E/W Fingertip
RCCS-14 N/S Fingertip
RMS-14 Pushbutton
RMLS-14 Momentary/Maintained
RHC-14 Hand
Wireless Hand
Dynasty TIGRunner comes with 8-ft. power cord (no plug),
quick reference guide, Coolmate™ 1.3 and Small Runner™ cart.
See page 7 for remote descriptions.
Water-Cooled
Packages
Use a single stock number
to order a complete
preconfigured system.
#195 054
#195 055
#300 429
#194 744
#151 086
#043 688
#187 208
#129 337
#242 211 020
#300 430
Step #3 • Select Torch Kit
W-250 (WP-20) Kit
W-280 (WP-280) Kit
(recommended)
W-375 Kit
#300 185
#300 990
#301 268
See page 7 for kit contents.
Select Water-Cooled Complete Package
#951 468
package shown.
Dynasty 280 (with CPS) Complete with Foot Control
Dynasty 280 DX (with CPS) Complete with Foot Control
Dynasty 280 DX (with CPS) Complete with Wireless Foot Control
#951 466
#951 468
#951 469
Comes with:
• 8-ft. power cord (no plug)
• Quick reference guide
• Coolmate™ 1.3 #300 972
• Coolant (4 one-gallon bottles of #043 810)
• Small Runner™ cart #300 988
• Remote control #194 744 (foot) or remote control #300 429 (wireless foot)
• W-280 (WP-280) torch kit #300 990 (see page 7 for contents)
6
Genuine Miller Accessories
®
Weldcraft™ A-200 (WP-26)
TIG Torch
#WP-26-12-R (12 ft.)
#WP-26-25-R (25 ft.)
200-amp air-cooled torch.
Torch body gas valve
models also available.
Small Runner™ Cart #300 988
Designed for Dynasty or
Maxstar 280 with or without a
Coolmate 1.3 cooler. Cart features
single cylinder rack, foot pedal
holder, two cable/torch holders,
and two TIG filler holders.
Note: A-200 (WP-26) torches require #195 379 connector.
Coolmate 1.3
#300 972 120 VAC
1.3-gallon cooler designed to
cool torches up to 280 amps.
™
Performance TIG Gloves
#263 345 X-Small (Women’s)
#263 346 Small (Women’s)
#263 347 Medium
#263 348 Large
#263 349 X-Large
Completely unlined, goat grain leather with
triple-padded palm.
Memory Card (Blank) #301 080
A blank, commercially available memory card used
for transferring software updates and expandable
features from your computer to the machine.
Memory Card Expansion
#301 151 14-Pin Automation Expansion
Provides the ability to access common automation
functions through the 14-pin connection.
#301 152 14-Pin Modbus® Expansion
Provides the ability to access basic and advanced
functions through the 14-pin connection.
#301 235 Independent AC Expansion
Allows EP and EN amperages and waveforms to
be set independently to precisely control heat
input to the work and electrode.
TIG Torches, Kits and Connectors
Contractor Kits
#195 054 150 A RFCS-14 HD Foot Pedal Kit
#195 055 150 A RCCS-14 Fingertip Kit
All-in-one TIG/Stick welding kit comes with
either a RFCS-14 HD foot control or RCCS-14
fingertip control, Weldcraft™ A-150 TIG torch,
200-amp Stick electrode holder with 15-foot
(4.6 m) cable, 300-amp work clamp with
15-foot (4.6 m) cable, flow gauge regulator
with 12-foot (3.7 m) gas hose, gas hose
coupler, AK2C torch accessory kit, and TIG
torch connector.
Air-Cooled TIG Torch
Connectors
#195 379 A-200 (WP-26)
#195 378* All others
50-mm Dinse-style for one-piece air-cooled torch.
*A-80 (WP-24) torches require 24-5 connector.
Water-Cooled Torch Kits
#300 185 W-250 (WP-20)
#300 990 W-280 (WP-280) (recommended)
#301 268 W-375
Kit comes with Weldcraft™ 25-foot (7.6 m)
TIG torch with Dinse-style connector, torch
cable cover, work clamp with 15-foot (4.6 m)
cable, flowmeter regulator with gas hose and
torch accessory kit (1/16-, 3/32- and 1/8-inch
2% ceriated tungsten, nozzles, collets and
collet bodies).
Water-Cooled TIG Torch
Connector #195 377
50-mm Dinse-style with
water return line. For use with all Weldcraft™
water-cooled torches.
Remote Controls and Switches
Wireless Remote Foot
Control #300 429
For remote current and
contactor control. Receiver
plugs directly into the 14-pin
receptacle of Miller machine. 90-foot (27.4 m)
operating range.
RFCS-14 HD Foot Control
#194 744
Maximum flexibility is accomplished with a reconfigurable
cord that can exit the front,
back or either side of the pedal. Foot pedal
provides remote current and contactor control.
Includes 20-foot (6 m) cord and 14-pin plug.
RCC-14 Remote Contactor and
Current Control #151 086
East/west rotary-motion fingertip control
attaches to TIG torch using two hook-and-loop
fasteners. Includes 26.5-foot (8 m) control cord
and 14-pin plug.
RCCS-14 Remote Contactor and
Current Control #043 688
North/south rotary-motion fingertip control
attaches to TIG torch using two hook-and-loop
fasteners. Includes 26.5-foot (8 m) cord and
14-pin plug.
RMS-14 On/Off Control
#187 208
Momentary-contact switch for contactor
control. Rubber-covered pushbutton dome
switch ideal for repetitive on-off applications.
Includes 26.5-foot (8 m) cord and 14-pin plug.
RMLS-14 Switch #129 337
Momentary- and maintainedcontact rocker switch for contactor control.
Push forward for maintained contact and
backward for momentary contact. Includes
26.5-foot (8 m) cord and 14-pin plug.
RHC-14 Hand Control
#242 211 020
Miniature hand control for
remote current and contactor
control. Dimensions: 4 x 4 x
3.25 inches (102 x 102 x 83 mm). Includes
20-foot (6 m) cord and 14-pin plug.
Wireless Remote Hand Control
#300 430
For remote current and contactor
control. Receiver plugs directly
into the 14-pin receptacle of
Miller machine. 300-foot
(91.4 m) operating range.
Educational Materials
To order, please call Miller Literature at 866-931-9732
or visit MillerWelds.com/resources/tools.
Gas Tungsten Arc Welding (TIG) Publication
#250 833
Setup DVD #251 116
Video topics include tungsten selection, setup
menus, DC pulse, sequencer, balance and
frequency settings.
Tungsten
Tungsten
Amp Range
2% Ceriated (AC/DC)
2% Lanthanated (AC/DC)
1/16 in. (1.6 mm)
70 –150 A
WC116X7
WL2116X7
3/32 in. (2.4 mm)
140 – 250 A
WC332X7
WL2332X7
1/8 in. (3.2 mm)
225 – 400 A
WC018X7
WL2018X7
5/32 in. (4.0 mm)
300 – 500 A
WC532X7
WL2532X7
7
Ordering Information
Equipment and Options
Stock No.
Description
Dynasty 280
Dynasty® 280 with CPS
Dynasty® 280 DX
Dynasty® 280 DX with CPS
#907 550
#907 537
#907 551
#907 514
Auto-Line 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
Water-Cooled Packages
Dynasty® 280 (with CPS) TIGRunner®
#907 537 002
Dynasty® 280 DX (with CPS) TIGRunner®
#907 514 001
Dynasty® 280 (with CPS) Complete w/Foot Control
Dynasty® 280 DX (with CPS) Complete w/Foot Control
Dynasty® 280 DX (with CPS) Complete
with Wireless Foot Control
#951 466
#951 468
#951 469
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
(Torch kit, accessories and coolant sold separately)
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
(Torch kit, accessories and coolant sold separately)
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
Auto-Line™ 208 – 575 VAC, 50/60 Hz, CSA. 8-ft. power cord
®
Accessories
Small Runner™ Cart
Coolmate™ 1.3
TIG Coolant (Must be ordered in quantities of four)
TIG Gloves
Memory Card (Blank)
Memory Card Expansion
TIG Torches, Kits and Connectors
Air-Cooled Contractor Kits
Weldcraft™ A-150 (WP-17) TIG Torch
Weldcraft™ A-200 (WP-26) TIG Torch
Air-Cooled TIG Torch Connectors
Water-Cooled Torch Kits
Water-Cooled TIG Torch Connector
Tungsten
#300 988
#300 972
#043 810
#301 080
#301 151
#301 152
#301 235
#195 055
#195 054
#WP-17-12-R
#WP-17-25-R
#WP-26-12-R
#WP-26-25-R
#195 379
#195 378
#300 185
#300 990
#301 268
#195 377
Remote Controls
Wireless Remote Foot Control
RFCS-14 HD
RCC-14
RCCS-14
RMS-14
RMLS-14
RHC-14
Wireless Remote Hand Control
#300 429
#194 744
#151 086
#043 688
#187 208
#129 337
#242 211 020
#300 430
Educational Materials
Gas Tungsten Arc Welding (TIG) Publication
Setup DVD
#250 833
#251 116
Date:
Distributed by:
© 2013 Miller Electric Mfg. Co.
Qty.
™
120 VAC, 60 Hz, CSA. Requires coolant
1-gallon plastic bottle. Protects against freezing to
-37° Fahrenheit (-38° C) or boiling to 227° Fahrenheit (108° C)
See page 7
14-pin automation expansion
14-pin Modbus® expansion
Independent AC expansion
Fingertip
Foot pedal
12-ft. (3.7 m) cable. Requires #195 378 connector
25-ft. (7.6 m) cable. Requires #195 378 connector
12-ft. (3.7 m) cable. Requires #195 379 connector
25-ft. (7.6 m) cable. Requires #195 379 connector
Connects Weldcraft™ A-200 (WP-26) torch to Dinse-style connector
Connects all air-cooled Weldcraft™ torches (except A-200) to
Dinse-style connector. A-80 (WP-24) torches require 24-5 connector
W-250 (WP-20)
W-280 (WP-280) (recommended for Dynasty 280)
W-375
Connects Weldcraft™ water-cooled torches to Dinse-style connector
See page 7
Foot control with wireless 90-ft. (27.4 m) operating range
Heavy-duty foot control
Side-to-side (east/west) fingertip control
North/south fingertip control
Momentary rubber dome switch
Momentary/maintained rocker switch
Hand control
Hand control with wireless 300-ft. (91.4 m) operating range
Total Quoted Price:
Price
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement