Zenith | PRO895X | Instruction manual | Zenith PRO895X Instruction manual

Zenith PRO895X Instruction manual
HD Projection Display
Operating Guide and Warranty
for User
Model
PRO895X
®
RECORD YOUR MODEL NUMBER
(Now, while you can see it)
The model and serial number of your new PRO895X are
located on the cabinet. For your future convenience, we
suggest that your record these numbers here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING :
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the product.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures: • Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.
PAGE 2
© Copyright 2001 Zenith Electronics Corporation
206-3701
IMPORTANT SAFETY INSTRUCTIONS
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential
electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read
and observe the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this operating guide can help you get many years of enjoyment and safe
operation that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions
9. Attachments
All the safety and operating instructions should be read
before the product is operated.
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
2. Follow Instructions
10. Ventilation
All operating and use instructions should be followed.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product
and to protect it from overheating, and these openings
must not be blocked or covered. The openings should never
be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
3. Retain Instructions
The safety and operating instructions should be retained
for future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall power outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water for example, near a
bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface or
on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by the
manufacturer.
8. Transporting Product
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home/business, consult your product dealer or local power company.
For products intended to operate from battery power, or
other sources, refer to the operating instructions.
12. Power-Cord Polarization
This product is equipped with a polarized
alternating-current power plug (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
(Continued on next page)
206-PRO895X
PORTABLE CART WARNING
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National
Electrical Code (U.S.A.), ANSI/ NFPA 70 provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
Example of Grounding According to National Electrical
Code Instructions
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC - National Electrical Code
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
20. Damage Requiring Service
Unplug this product from the wall power outlet and refer
servicing to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the cabinet has
been damaged.
f. If the product exhibits a distinct change in
performance.
15. Lightning
21. Replacement Parts
For added protection for this product (receiver) during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall power
outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and
power-line surges.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
16. Power-Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be
fatal.
17. Overloading
Do not overload wall power outlets and extension cords as
this can result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through
PAGE 4
22. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating
condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide
or fall causing serious injury to a child or adult and serious
damage to the product.
24. Heat
The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
206-3701
CONTENTS
SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . 3 - 4
INTRODUCTION
Installer’s Experience Level . . . . . . . . . . . . . . . . . . . . . . . 6
Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . 6
National Power Cord Requirements U.S., Canada . . . . . . . . . . 6
STANDARD CONNECTIONS
Connections Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connections Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connections Center Input and Controls
Description/Function . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting Computer Video Sources . . . . . . . . . . . . . . . . . 8
Connecting Video and S-Video Sources . . . . . . . . . . . . . . . . 8
USER’S QUICK REFERENCE GUIDE
Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Basic Operation: Projecting a Picture . . . . . . . . . . . . . . . . . 9
Using a Computer as a Video Source . . . . . . . . . . . . . . . . 10
Using a VCR or other Video Source . . . . . . . . . . . . . . . . . 11
Using an S-Video VCR or other S-Video Source . . . . . . . . . . 12
UNIVERSAL MULTI-BRAND REMOTE CONTROL
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming Your Remote to Operate Other IR Devices . . . . 13
Amplifier Volume Override . . . . . . . . . . . . . . . . . . . . . . . 14
AUX 1- 2 -3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Auto Find: Automatic Brand Code Search . . . . . . . . . . . . . 16
Other Brand Equipment Programming Codes . . . . . . . . 17 - 18
Remote Key Functions in Other Operating Modes . . . . . . . . 19
Remote key functions for Analog TV . . . . . . . . . . . . . . . . 20
ON-SCREEN MENUS AND DISPLAYS
Available Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Basic Menu Operation (Selecting and Adjusting Menu
Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Source/Time Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SOURCE MENU
Available Source Menu Options: Video, S-Video, RGB . . . . . . 22
Changing Input Source . . . . . . . . . . . . . . . . . . . . . . . . . 22
Input Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SETUP MENU
Setup Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Enable/Disable On/Off Timer . . . . . . . . . . . . . . . . . . . . . 24
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Video Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Aspect Ratio (Picture Proportion) . . . . . . . . . . . . . . . . . . 25
Format Pref. (Preference) . . . . . . . . . . . . . . . . . . . . . . . 26
Label Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Blank Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Static Setup (Red, Blue, Green Convergence) . . . . . . . . . . . 27
VIDEO MENU
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Video Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
RGB Source Special Adjustments . . . . . . . . . . . . . . . . . . . 29
MAINTENANCE AND TROUBLESHOOTING
Caring for Your HD Projection Display . . . . . . . . . . . . . . . 30
Cabinet Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Lens Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Extended Absence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Picture Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Before Calling For Service . . . . . . . . . . . . . . . . . . . . . . . 31
Problem Identification Chart . . . . . . . . . . . . . . . . . . . . . 31
RGB Source Problems . . . . . . . . . . . . . . . . . . . . . . . . . . 31
YOUR ZENITH WARRANTY . . . . . . . . . . . . . . . . . . . Back Cover
Note: All design and specifications are subject to change without prior notice.
PRO895X Features
•
•
•
•
•
•
Multi-Input Video Jacks
Multi-Brand Programmable Universal Remote Control
24 Hour Clock
Sleep Timer
On/Off Timer with Multiple Settings
Source Format Memory
•
•
•
•
•
•
Video Loop-Out jack
Auto Signal Format Selection Mode
On-Screen Menus
On-Screen Status Display
Multi-Language On-Screen Menu Options
Source Format Labeling
Notes To Users: Do Installation First
Do not operate this equipment until installation has a been
completed by qualified service personnel! This is the PRO895X
Operating Guide and Warranty. Before this equipment is ready to
be operated on a day-to-day basis, installation should be completed. See the PRO895X Installation and Setup Guide for
206-PRO895X
System Installer. after installation, use only your Universal
remote for everyday operation! Refer any questions about the
content of this Operating Guide and Warranty to service personnel who have a background at least equivalent to that of an
Electronics Technician.
PAGE 5
INTRODUCTION
INSTALLER’S EXPERIENCE LEVEL
Your new HD Projection Display is a sophisticated entertainment appliance. In addition to making the necessary connections, installation will
most likely require a series of adjustments to
ensure the projected image is not distorted. If these
adjustments are not accurate, the operation of the display
could be adversely affected. For this reason, installation
and setup should be performed by a qualified service person and should conform to all local codes. The installer
must also adhere to the pertinent Articles of the National
Electrical Code (NEC), pertinent Regulations of the Federal
Communications Commission (FCC), and all relevant codes
of local regulating agencies.
INSTALLATION CONSIDERATIONS
Before you install your PRO895X...
Ventilation -- Proper ventilation keeps your
PRO895X running cool. Air circulates through
perforations on the sides of the cabinet. Do not
block these vents or you will shorten the life of
the display.
Power Cord -- This product has a three-wire
grounding-type plug having a third (grounding)
pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the grounding-type plug.
Power Source -- Your PRO895X is designed to
operate on standard current, 120 volt 60 Hertz
AC or 230 volt 50/60 Hertz AC. Do not attempt
to operate it on DC current. Your display is configured at the factory for 120 volt, 60 Hz operation. A
service adjustment is necessary to permit the unit to operate on 230 volt, 50/60 Hz. See Changing From 120 VAC To
230 VAC in the Placement and Configuration section in the
Installation Guide for System Installer for details.
Projection Surface -- We recommend a good quality screen
having a matte white finish, that measures 100” or more
diagonally. Contact your local dealer for purchasing an
appropriate screen.
Note: Use of a projection screen designed for a single light
source projection system may result in significant side-to-side
color distortion.
PAGE 6
NATIONAL POWER CORD REQUIREMENTS U.S., CANADA
• The power cord must be UL listed and CSA certified.
• The minimum specifications for the
power cord are as follows: No. 18
AWG, Type SV or SJ, 3 conductor.
• The power cord must have a rated
current capacity of at least 10
amperes.
• The attachment plug must be an
earth-grounding type with a NEMA 515P (15A, 125V) or NEMA 6-15P (15A,
250V) configuration.
Standard North America
(120 VAC)
North America (240 VAC)
OTHER COUNTRIES
• The cord set fittings must bear the certification mark of
the agency responsible for evaluation in a specific
country. Acceptable agencies include the following:
BSI (United Kingdom)
Nemko (Norway)
CEBEC (Belgium)
OVE (Austria)
DEMKO (Denmark)
SEMKO (Sweden)
EANSW (Australia)
SEV (Switzerland)
SETI (Finland)
UTE (France)
IMQ (Italy)
VDE (Germany)
KEMA (The Netherlands) MITI (Japan)
• The flexible cord must be of a HAR (harmonized) type
HO5VV-F 3-conductor cord with a minimum conductor
size of .03 square inches (1.0 square millimeter).
• The cord set must have a current capacity of at least 10
amperes and a nominal voltage rating of 125 or 250 VAC,
as required by the specific country’s power system.
HD INTRO B-5-99
STANDARD CONNECTIONS
CONNECTIONS CENTER
CONNECTIONS OPTIONS
You have a choice of these video source connections: Video
In; S-Video In; and RGB with H/V Sync and V Sync. Use the
COMM jack to connect a computer serial port.
You can connect equipment such as a: laser disc player,
VCR, computer, satellite receiver, or camcorder, (most
equipment that provides a video output).
CONNECTIONS CENTER INPUT AND CONTROLS DESCRIPTION/FUNCTION
1. Remote Control Window — Receives the infrared signal
sent by the remote.
Note: Another remote control signal receiving window is
located on the front of the PRO895X.
2. Up/Down/Left/Right arrows — Select and adjust onscreen menu options.
3. ENTER — Use when an enter function is required.
4. MENU — Accesses on-screen menus.
5. POWER — Turns PRO895X On and Off.
6. Power On Indicator — Lights when power is On.
7. R,G,B, H/V SYNC, V SYNC — Connect a video source that
provides video signals in the form of Red, Green, Blue,
Horizontal, Vertical Sync Outputs, to these input jacks.
3275-A
8. Video In Jack — Connects a video source with a
composite video output to this jack.
9. Loop Out Jack — Provides the same VIDEO IN signal to
another component.
Note: Set Loop Out/In switch to “Out” if you connect a
video source to the Loop Out jack.
10.Loop Out/In Switch — Should be in the “In” position
unless a video source is connected to the Loop Out jack.
Note: Failure to set switch to proper position could
result in a video overload or a washed out video.
11. S-Video — Connect a video source with an S-Video jack
(Y- C Connector) to this input jack.
12. COMM — Connect a computer or serial device to this
jack.
PAGE 7
STANDARD CONNECTIONS
CONNECTING COMPUTER VIDEO SOURCES
Connect a video source such as a computer: PC, Laptop, or Notebook type.
To hook up a laptop or computer, use a cable with a
15-pin D type connector on one end and BNC connectors
on the other end.
Note: Any special adapters, cables, or connectors shown
are not provided with the PRO895X. See your computer
dealer for your special requirements.
CONNECTING VIDEO AND S-VIDEO SOURCES
Connect video sources with a tuner, (VCR) or other video sources such as a DVD player
or satellite receiver.
To hook up a VCR, DVD player, or other video source,
use standard video connectors as needed.
Connect the video source to
the Video In jack on the
PRO895X. If the video
source has an S-Video connector, then connect to the
S-Video jack on the
PRO895X.
PAGE 8
Notes: For audio capability,
connect your Video sources’
Audio output to a separate
audio amplifier like a stereo
system; no audio capability
is provided with the
PRO895X. Use cables and
adapters with the connector
types and jacks available on
the video source.
206-3275-A
USER’S QUICK REFERENCE GUIDE
SETUP CHECKLIST
Turn on all system components including the
video source you intend to watch; video source
is the video equipment connected to the HD
Display connection center.
Turn on the PRO895X.
Select a video source from one of the video
inputs provided on the connection center:
Video In, S-Video In, or RGB input jacks.
Set the PRO895X internal clock.
The internal clock must be set before the Timer
Menu option will appear in the Setup Main Menu.
Select English, Spanish, French, or German for onscreen menus.
Use other options (fine-tune video image).
BASIC OPERATION: PROJECTING A PICTURE (Remote operates the PRO895X in TV mode)
Once the PRO895X has been installed and set up, follow these
simplified instructions for operation. Be sure to install batteries
in the remote.
PRG
Projecting a Picture
1. Press TV on remote to operate the PRO895X.
2. Point remote toward PRO895X screen, press POWER to
turn PRO895X on. (Be sure all video sources are also
turned on.)
3. Press MENU to display and access the on-screen menus.
4. Press MENU repeatedly to highlight the Source menu.
5. Use the Up/Down arrow to select the input source you want
to project on the screen, press ENTER.
6. Make any other necessary on-screen menu adjustments
using the Up/Down/Left/Right arrows for the Setup and
Video Menus. (Up/Down arrows select options, Left/Right
arrows adjust or change settings). Press QUIT to exit menu.
7. When finished using the PRO895X, press TV, press POWER to
turn the PRO895X off.
Audio Amplifier Note:
Reference is made to an audio amplifier. The user-supplied
audio amplifier may be a stereo system. In that case, connect
Right and Left Audio Out from the video source you are using
to Right and Left Audio In on the audio amplifier.
206-3701
CABLE
VCR
POWER
2/7
TV
1/7
AUX
MUTE
FLASHBK
SURF
CHANNEL
VOLUME
VOLUME
CHANNEL
1
2
3
4
5
6
7
8
9
0
3/4
5/6
QUIT
MENU
PIP
pip ch
RECORD
4/5/6
ENTER
CC
FREEZ
PAUSE
TIMER
5/6
TV/VCR
SOURCE
PLAY
REWIND
FFWD
STOP
MBR3458CT
124-233-06
PAGE 9
USER’S QUICK REFERENCE GUIDE
USING A COMPUTER AS A VIDEO SOURCE
Use the Universal Remote to Access On-screen Menus and Make Changes
Once the PRO895X has been installed and set up, follow these simplified instructions for operation. Be sure to install
batteries in the remote. See Remote control section for further instructions regarding remote operation.
Computer Setup Instructions
Connections Computer to PRO895X
Menus
Format
Source Menu Select RGB as input source.
Setup Menu Select Aspect Ratio 4 x 3.
Select Static Setup and adjust if necessary.
Video Menu Make RGB Source adjustments if necessary.
Current Source: RGB
Press
to Select Input
Press ENTER to change.
Source Menu with RGB
selected as Input Source
If the new video source has not been connected before, it may be in a
format not recognized by the PRO895X. If the new format is not
recognized, save it and give it a name.
Adjustments Make any additional image adjustments as required for this unique
setup. See the “Installation and Setup Guide for System Installer” for
set up instructions.
PAGE 10
206-PRO895X
USERS QUICK REFERENCE GUIDE
USING A VCR, OR OTHER VIDEO SOURCE
Use the Universal Remote to Access On-screen Menus and Make Changes
Once the PRO895X has been installed and set up, follow these simplified instructions for operation. Be sure to install
batteries in the remote. See Remote control section for further instructions regarding remote operation.
Note: If Video In is used without a connection to loop out, “Loop Out Switch” must be put to the “In Only” position.
VCR or other Video Source Setup Instructions
Connections VCR to Video In on PRO895X
VCR Audio Out to Audio In of User-Supplied Stereo System or
Audio Amplifier.
Menus
Source Menu Select Video as input source.
Setup Menu Select Aspect Ratio and select proper ratio.
Select Static Setup and adjust if necessary.
Video Menu Make RGB Source adjustments if necessary.
Format
If the new video source has not been connected before, it may
be in a format not recognized by the PRO895X. If the new
format is not recognized, save it and give it a name.
Adjustments Make any additional image adjustments as
required for this unique setup. See the “Installation and Setup
Guide for System Installer” for set up instructions.
206-3275-A
Current Source:
Video
Press
to Select Input
Press ENTER to change.
Source Menu with Video
selected as Input Source
PAGE 11
USERS QUICK REFERENCE GUIDE
USING AN S-VIDEO VCR OR OTHER S-VIDEO SOURCE
Use the Universal Remote to Access On-screen Menus and Make Changes
Once the PRO895X has been installed and set up, follow these simplified instructions for operation. Be sure to install
batteries in the remote. See Remote control section for further instructions regarding remote operation.
S-Video VCR or other S-Video Source Setup Instructions
Connections S-Video Out to S-Video In on PRO895X
VCR Audio Out to Audio In of User-Supplied Stereo System or
Audio Amplifier.
Menus
Source Menu Select S-Video as input source.
Setup Menu Select Aspect Ratio and select proper ratio.
Select Static Setup and adjust if necessary.
Video Menu Make S-Video Source adjustments if necessary.
Format
If the new S-Video source has not been connected before, it
may be in a format not recognized by the PRO895X. If the
new format is not recognized, save it and give it a name.
Adjustments Make any additional image adjustments as required for this
unique setup. See the “Installation and Setup Guide for System
Installer” for set up instructions.
PAGE 12
Current Source: S-Video
Press
to Select Input
Press ENTER to change.
Source Menu with S-Video
selected as Input Source
206-3701
UNIVERSAL MULTI-BRAND REMOTE CONTROL
INTRODUCTION
This multi-brand remote operates the common features of most, but not all, models and brands of infrared controlled products. If some functions of your particular product cannot be controlled by this remote, use the original remote.
BATTERY INSTALLATION
Batteries are provided, but must be installed before using the remote control. When the remote no longer functions normally, or if it loses memory,
replace the batteries with three high-quality, alkaline, size AAA batteries.
Match positive with positive (+ with +), and negative with negative
(- with -) as shown inside the battery compartment.
Notes
back of
remote
• Do not place heavy objects on top of the remote keys; prolonged unintentional
remote operation shortens battery life.
• Remove the batteries if the remote will not be used for a month or more. Battery
leakage can permanently damage the remote, for which Zenith is not responsible.
PROGRAMMING YOUR REMOTE TO OPERATE OTHER IR
(Infra-red) DEVICES
Indicator Light
3
POWER
PRG
CABLE
1. Turn on the device you want to program.
AUX
TV
MUTE
FLASHBK
SURF
2. On the chart on page 17/18, find the type of device you’re
programming, and then find the brand name. Make a note of the three-number code, you’ll need it soon.
CHANNEL
VOLUME
VOLUME
CHANNEL
3. Press and hold PRG. It’s recessed so it doesn’t get pushed accidentally.
Use a small, blunt object. When the indicator light turns on, release PRG.
4. Push the key name with the type of device you’re programming (VCR,
CABLE, or AUX, DO NOT PROGRAM TV MODE).
VCR
5
1
2
3
4
5
6
7
8
9
0
5. Using the NUMBER keypad, enter the three-number code you found on
page 17/18.
7. Point the remote at the device and push POWER. It should turn off. If
not, try the other codes listed and continue from step three.
PIP
QUIT
pip ch
RECORD
206-3701
CC
FREEZ
PAUSE
TV/VCR
SOURCE
TIMER
PLAY
REWIND
Notes
• To reset remote to factory settings, enter 9-1-1, in Step 5. After programming, be
sure to press the mode key first to operate the device you have just programmed.
• The VCR mode will only accept codes for VCRs. The AUX 1, AUX 2, and Cable modes
will accept codes for any kind of IR controlled product.
• To get out of Programming mode before you enter a code, just press QUIT on your
remote.
6
ENTER
MENU
6. Press ENTER to save the code. (The indicator light will flash 3 times,
then turn off to indicate the code is valid.)
7
4
FFWD
STOP
MBR3458CT
124-233-06
PAGE 13
UNIVERSAL MULTI-BRAND REMOTE CONTROL
CONTROL THE VOLUME ON YOUR HOME AUDIO SYSTEM WITHOUT CHANGING MODES
Indicator Light
Amplifier Volume Override
1. Find the code that operates your amplifier. Test it to
make sure it’s the correct one by following the procedure in
“Programming Your Remote” on the previous page.
2. Program your audio system into one of the available AUX
modes: Aux, Aux+1, Aux+2, or Aux+3.
3
POWER
PRG
CABLE
2
VCR
MUTE
CHANNEL
VOLUME
VOLUME
CHANNEL
4. Press 4-9-9; then ENTER on the remote. The indicator
light will flash three times the code was accepted.
Audio system volume/mute now appears in all modes.
1
2
3
4
5
6
7
8
9
0
PAGE 14
TV
FLASHBK
SURF
3. Press and hold PRG on your remote until the indicator
light stays lit, then release.
Notes
• You can also program Cable Box Volume and Mute control
(if available) into your cable box mode (CABLE or AUX
mode) by repeating the steps for programming on the previous page but entering 3-9-9, instead of a brand code, then
pressing ENTER.
• To put everything back to normal, reprogram the mode
from step 3 with the original brand code.
• If you can’t find the code for your amplifier, use the Auto
Find feature on page 16.
AUX
ENTER
QUIT
MENU
PIP
RECORD
2/4
pip ch
PAUSE
FREEZ
TIMER
CC
TV/VCR
SOURCE
PLAY
REWIND
FFWD
STOP
206-3275-A
UNIVERSAL MULTI-BRAND REMOTE CONTROL
CONTROL UP TO SEVEN DIFFERENT DEVICES WITH YOUR REMOTE
Indicator Light
AUX 1 - 2 - 3
1. Refer to the chart on page 17/18 to find the type and brand
name of the device you're programming.
2
3
POWER
PRG
CABLE
VCR
TV
MUTE
FLASHBK
SURF
2. Press and hold down PRG with a small blunt object until the
indicator light turns on, then release PRG.
3. Press AUX and the 1 on the NUMBER keypad at the same time
(for AUX +1).
AUX
6
CHANNEL
VOLUME
VOLUME
CHANNEL
4. Using the NUMBER keypad, enter the three-number code for
the device you've selected.
1
2
3
4
5
6
5. Press ENTER to save the code.
7
8
9
6. With the device turned on, point the remote at it and press
POWER. It should turn off.
0
4
5
ENTER
QUIT
MENU
Repeat the above steps for AUX+2, and AUX+3.
PIP
Notes
• Programming your Zenith remote may allow you to use one
remote to work up to 7 different products or devices.
• AUX Auxiliary equipment can be any equipment which does not
have a dedicated key on your remote like Cable or VCR. Typically a
second VCR, stereo system, audio tape deck, etc.
• Some devices may not work with your Zenith remote control.
206-3275-A
RECORD
pip ch
FREEZ
PAUSE
TIMER
CC
TV/VCR
SOURCE
PLAY
REWIND
FFWD
STOP
PAGE 15
UNIVERSAL MULTI-BRAND REMOTE CONTROL
USE AUTOFIND TO AUTOMATICALLY SEARCH AND TRY ALL POSSIBLE BRAND CODES
Indicator Light
AutoFind
1. Turn on the device you want the remote to control.
2. Press and hold PRG until the indicator light turns on, then
release PRG.
2
3
POWER
PRG
CABLE
VCR
AUX
3. Press the key for the device you are trying to program (CABLE,
VCR, AUX, TV).
CHANNEL
VOLUME
4. Press 0-0-0 (zero-zero-zero), then press ENTER right away.
7. Press POWER to turn the device back on.
4
1
2
3
4
5
6
7
8
9
0
PAGE 16
RECORD
4/6
ENTER
QUIT
MENU
PIP
Notes
• You can quickly get out of Auto Find by pressing PRG.
• If the indicator light stays on while you press Power instead of
turning off, all the codes have been tried and your device can’t be
controlled.
• AUTO FIND is an additional way of finding a brand code for controlling auxiliary equipment such as a VCR, DVD player, etc. that is
not available through the regular remote brand code programming
method.
VOLUME
CHANNEL
5. Aim the remote at the correct device and push the POWER
key (The indicator light will turn off while the POWER key is
pressed). Allow a second to pass, then push the POWER key again.
Repeat until the device turns off.
6. Push ENTER to save the code (The indicator light will flash 3
times and then turn off).
TV
MUTE
FLASHBK
SURF
5/7
pip ch
FREEZ
PAUSE
TIMER
CC
TV/VCR
SOURCE
PLAY
REWIND
FFWD
STOP
206-3275-A
UNIVERSAL MULTI-BRAND REMOTE CONTROL
FIND THE CODES YOU NEED TO PROGRAM YOUR REMOTE. ON THIS PAGE: TVS, VCRS, CABLE BOXES,AND HD/SET TOP BOXES
TVs
Daewoo . . . . . . . 149
Zenith . . . . . . . . 101 121 149
152
Zenith TV/VCR . . . 150 152 153
154 172
TV/VCR Combination Codes
Funai TV/VCR. . . . 154
Adventura TV/VCR . 154
Goldstar TV/VCR . . 153 172
Daewoo TV/VCR . . 148
Symphonic TV/VCR 154
General Electric . . 216 220 266
282 701 702
725
MultiTech. . . . . . . 727
Samsung . . . . . . . 220 230
NEC . . . . . . . . . . 267 268 269
281 292 709
726
Sansui . . . . . . . . 289 292 709
726
VCRs
Admiral . . . . . . . 261
Akai . . . . . . . . . . 292 717 718
719 720
Audio Dynamics . . 726
Go Video . . . . . . . 256 262 263
700
Bell & Howell . . . . 247
Goldstar . . . . . . . 253
Broksonic . . . . . . 221 250 255
729
Harmon Kardon . . . 296
Candle . . . . . . . . 727
Hitachi . . . . . . . . 257 270 273
292 705 706
707 708
Canon . . . . . . . . . 704
J.C. Penny . . . . . . 268 726
Capeheart . . . . . . 728
Jensen . . . . . . . . 292
Citizen . . . . . . . . 727
Craig . . . . . . . . . 212
Curtis Mathes . . . 259 266 725
727
Daewoo . . . . . . . 244 246 248
254 703 729
Daytron . . . . . . . 246
JVC . . . . . . . . . . 224 225 258
268 292 299
726
Kenwood . . . . . . . 268 292 726
727
Magnavox . . . . . . 275
DBX . . . . . . . . . . 726
Marantz . . . . . . . 267 268 726
727
Electrochrome. . . . 730
Memorex . . . . . . . 212 298
Emerson . . . . . . . 203
250
722
731
221 243
293 721
729 730
732
Fisher . . . . . . . . . 211 212 213
247 265 274
MGA . . . . . . . . . . 297 730
Mitsubishi . . . . . . 276 277 278
279 280 296
297 730
Montgomery Ward
216 219 249
291 730
Orion . . . . . . . . . 250
Sanyo . . . . . . . . 212 247 294
Scott . . . . . . . . . 243 290 729
Panasonic . . . . . . 245 251 259
713 714 715
716
Sears . . . . . . . . . 211 212 213
265 274
Pentax . . . . . . . . 708 727
Sharp . . . . . . . . . 261 730
Philco . . . . . . . . . 275
Signature 2000 . . . 216 219 249
Pioneer . . . . . . . 210 282 726
Sony . . . . . . . . . 232 723 724
Portland . . . . . . . 246 727
Sylvania . . . . . . . 275 297
ProScan . . . . . . . 216 260 266
282 725
Tatung . . . . . . . . 268 292
Quasar . . . . . . . . 259 295
Teknika . . . . . . . . 272
Radio Shack . . . . . 213 265 730
RCA . . . . . . . . . . 216
240
260
283
286
708
725
220
242
266
284
287
710
Teac . . . . . . . . . . 268
228
249
282
285
288
711
Realistic . . . . . . . 212 213 265
730
Saisho. . . . . . . . . 722
Salora . . . . . . . . . 297
Toshiba . . . . . . . . 213 274 290
297
Vector Research . . 726 727
Victor . . . . . . . . . 726
Video Concepts . . . 726 727
XR - 1000 . . . . . . 243
Yamaha . . . . . . . . 726
Zenith . . . . . . . . 201 224 225
229
Cable Boxes
Allegro . . . . . . . . 358 362
Allegro A-B Switch 361
Archer . . . . . . . . 325
Century . . . . . . . . 325
Citizen . . . . . . . . 325
Comtronic . . . . . . 326
Everquest . . . . . . 379
Garrard . . . . . . . . 325
350 352 354
355
Hamlin . . . . . . . . 302 303 345
365 366
Jasco . . . . . . . . . 325
Pioneer . . . . . . . . 315 343
Jerrold . . . . . . . . 304 307 308
309 310 318
360 363
RCA . . . . . . . . . . 341
Kale Vision . . . . . 335
Samsung . . . . . . . 326 335
Macom . . . . . . . . 321
Scientific Atlanta
Magnavox . . . . . . 327 334
Regency . . . . . . . 329
316 323 336
337 364
Signal . . . . . . . . . 326
Gemini . . . . . . . . 305 331 338
NSC . . . . . . . . . . 335 339 368
369 370
SL Marx . . . . . . . . 326
General Electric. . . 367
Oak . . . . . . . . . . 311 332 342
Sprucer . . . . . . . . 313
General Instrument 304 305 306
307 308 309
310 318
Panasonic . . . . . . 313 320
Standard Comp . . . 335
Philips . . . . . . . . 325 327 347
Stargate . . . . . . . 326 379
Echostar . . . . . . . 805
Philips . . . . . . . . 802
Sony . . . . . . . . . 801
Hughes . . . . . . . 803
RCA . . . . . . . . . . 804
Zenith . . . . . . . . 800
Teleview . . . . . . . 326
Texscan . . . . . . . 339 356 371
Tocom . . . . . . . . 317 318 346
Unika . . . . . . . . . 325 348 362
Universal . . . . . . 325 358 362
Vid Tech . . . . . . . 340
Video Way . . . . . . 349
Viewstar . . . . . . . 327 354 355
372
Zenith HT-2000. . . 353
Zenith PM . . . . . . 374
HD/Set Top Boxes
206-3275-A
PAGE 17
UNIVERSAL MULTI-BRAND REMOTE CONTROL
FIND THE CODES YOU NEED TO PROGRAM YOUR REMOTE. ON THIS PAGE: CABLE, SATELLITE, CD PLAYERS, TAPE DECKS,
AUDIO TUNERS AND AMPLIFIERS.
Satellite Receivers
Alphastar. . . . . . . 516
Hughes Network . . 514
RCA . . . . . . . . . . 510 517
Toshiba . . . . . . . . 509 512
Chaparral . . . . . . . 501 502
JVC . . . . . . . . . . 518
Realistic . . . . . . . 506
Uniden . . . . . . . . 522
Cheyenne. . . . . . . 502
Macom . . . . . . . . 314
Sierra I . . . . . . . . 502
United . . . . . . . . 344
Dishnet . . . . . . . . 515
Magnavox . . . . . . 521
Sierra II . . . . . . . 502
Zenith Drake. . . . . 312 330
Drake . . . . . . . . . 503
Phillips . . . . . . . . 521
Sierra III . . . . . . . 502
General Electric. . . 510 517
PrimeStar. . . . . . . 513
Sony. . . . . . . . . . 511
Zenith Satellite . . 328 351 378
500
General Instrument 504 505
ProScan. . . . . . . . 510 517
STS1 . . . . . . . . . . 507
Hitachi . . . . . . . . 519 520
RCA DSS . . . . . . . 373
STS3 . . . . . . . . . . 508
JVC . . . . . . . . . . 965
Pioneer . . . . . . . . 963
Toshiba . . . . . . . . 961
Mitsubushi . . . . . . 964
Sony. . . . . . . . . . 962
Zenith. . . . . . . . . 960
DVD Players
Audio CD Players
ADC . . . . . . . . . . 940
JVC . . . . . . . . . . 949 954
Panasonic . . . . . . 431 432 945
ADO . . . . . . . . . . 939
Kenwood . . . . . . 441 931 948
Phillips . . . . . . . . 421 433 434
Aiwa. . . . . . . . . . 938
Luxman . . . . . . . . 930
Pioneer . . . . . . . . 431 435 944
Akai . . . . . . . . . . 937
Magnavox . . . . . . 421 422 433
434
Quasar . . . . . . . . 432
Denon . . . . . . . . 935
Dynatech . . . . . . . 953
Emerson . . . . . . . 952
Fisher . . . . . . . . . 438 933 951
GE . . . . . . . . . . . 932
Goldstar . . . . . . . 460
Hitachi . . . . . . . . 950
Marantz . . . . . . . . 929 947
MCS . . . . . . . . . . 928
Mitsubishi . . . . . . 927
Nakamichi . . . . . . 925 926
Onkyo . . . . . . . . 923 924 946
Optimus . . . . . . . 920 921 922
Radio Shack . . . . . 431 441
RCA . . . . . . . . . . 437 943
Sanyo . . . . . . . . . 438 439
Sears . . . . . . . . . 936
445 934
Soundesign . . . . . 461 498 901
902
Sylvania . . . . . . . 433
Teac . . . . . . . . . 418 419
Technics . . . . . . . 432
Toshiba . . . . . . . . 915
Yahama . . . . . . . . 414 941 942
Sharp . . . . . . . . . 441 442
Zenith . . . . . . . . 460 461 498
901 902
Sherwood . . . . . . 449
Zenith CD Rec . . . 415
Sony. . . . . . . . . . 420 443 444
Audio Tape Decks
Sony. . . . . . . . . . 452
Audio Tuners/Amps
Citizen . . . . . . . . 914
Marantz . . . . . . . . 903 913
Pioneer . . . . . . . . 470 485 907
GE . . . . . . . . . . . 916
Memorex . . . . . . . 485
Proton . . . . . . . . 910
Goldstar . . . . . . . 460 474
Nad . . . . . . . . . . 904
Quasar . . . . . . . . 912
Hitachi . . . . . . . . 919
Nakamichi . . . . . . 493
RCA . . . . . . . . . . 909
JVC . . . . . . . . . . 908
Onkyo . . . . . . . . 471 906
Sharp . . . . . . . . . 483 917 918
Kenwood . . . . . . . 484
Optimus . . . . . . . 905
Sherwood . . . . . . 900
Luxman . . . . . . . . 467
Panasonic . . . . . . 912
Sony. . . . . . . . . . 486 489 490
491 492
PAGE 18
Soundesign . . . . . 461 498 901
902
Toshiba . . . . . . . . 915
Techniques. . . . . . 912
Victor . . . . . . . . . 908
Zenith . . . . . . . . 460 461 498
901 902
206-3275-A
UNIVERSAL MULTI-BRAND REMOTE CONTROL
Key functions in TV, VCR, Cable, and AUX operating modes
KEY NAME
PRG
POWER
CABLE
VCR
AUX
TV
Surf
FLASHBK
MUTE
CHANNEL UP
CHANNEL DOWN
VOLUME (RIGHT)
VOLUME (LEFT)
1
2
3
4
5
6
7
8
9
0
ENTER
MENU
UP ARROW
DOWN ARROW
LEFT ARROW
RIGHT ARROW
QUIT/(Note)
PIP
PIP CH
FREEZ
CC
TIMER
TV/VCR/SOURCE
RECORD
PAUSE
REWIND
PLAY
STOP
FFWD
References:
TV Mode
Zenith Code 101
VCR Mode
Zenith Code 201
Cable Mode
Zenith Code 353
AUX Mode
Zenith Code 960
Program Mode Codes
TV On/Off
Selects Cable
Selects VCR
Selects AUX
Selects TV
Surf Channels On/Off
TV Flashback
TV Mute
TV Channel Up
TV Channel Down
TV Volume Up
TV Volume Down
TV Digit 1
TV Digit 2
TV Digit 3
TV Digit 4
TV Digit 5
TV Digit 6
TV Digit 7
TV Digit 8
TV Digit 9
TV Digit 0
TV Enter
TV Menu
TV Select Up
TV Select Down
TV Adjust Left
TV Adjust Right
TV Surr Sound
TV PIP
TV/PIP Channel Tune
TV PIP Freeze
TV Closed Captions
TV Timer
TV Sources
VCR Record
VCR Pause
VCR Rewind
VCR Play
VCR Stop
VCR Fast Forward
Program Mode Codes
VCR On/Off
Selects Cable
Selects VCR
Selects AUX
Selects TV
VCR SP/EP
VCR Flashback
TV Mute
VCR Channel Up
VCR Channel Down
TV Volume Up
TV Volume Down
VCR Digit 1
VCR Digit 2
VCR Digit 3
VCR Digit 4
VCR Digit 5
VCR Digit 6
VCR Digit 7
VCR Digit 8
VCR Digit 9
VCR Digit 0
VCR Enter
VCR Menu
VCR Select Up
VCR Select Down
VCR Adjust Left
VCR Adjust Right
VCR Quit
VCR+
VCR Eject Tape
VCR Commercial Skip
VCR Memory
VCR Timer
TV Tuner or VCR Tuner
VCR Record
VCR Pause
VCR Rewind
VCR Play
VCR Stop
VCR Fast Forward
Program Mode Codes
Cable Box On/Off
Selects Cable
Selects VCR
Selects AUX
Selects TV
Cable FC/Fav Ch
Cable Flashback
TV Mute
Cable Channel Up
Cable Channel Down
TV Volume Up
TV Volume Down
Cable Digit 1
Cable Digit 2
Cable Digit 3
Cable Digit 4
Cable Digit 5
Cable Digit 6
Cable Digit 7
Cable Digit 8
Cable Digit 9
Cable Digit 0
Cable Enter
Cable Menu
Cable Up Arrow
Cable Down Arrow
Cable Left Arrow
Cable Right Arrow
Cable Quit
Day Up
Day Down
Cable Page Up
Cable Page Down
Cable Timer
Cable Info
Cable Buy
Cable Guide
VCR Rewind
VCR Play
VCR Stop
VCR Fast Forward
Program Mode Codes
AUX On/Off
Selects Cable
Selects VCR
Selects AUX
Selects TV
AUX Audio
AUX Return
TV Mute
AUX Skip >>
AUX Skip <<
TV Volume Up
TV Volume Down
AUX Digit 1
AUX Digit 2
AUX Digit 3
AUX Digit 4
AUX Digit 5
AUX Digit 6
AUX Digit 7
AUX Digit 8
AUX Digit 9
AUX Digit 0
AUX Display
AUX Menu
AUX Up Arrow
AUX Down Arrow
AUX Title
AUX Sub-Title
AUX Resume
AUX Marker
AUX Marker Search
AUX Repeat-Chap
AUX Repeat A-B
AUX Program
AUX Open/Close
AUX Angle
AUX Pause
AUX Scan <<
AUX Play
AUX Stop/Eject
AUX Scan >>
MBR3458CT, 124-233-06 and µP 221-1445-02
Some of the functions shown above may not be available on your equipment.
206-3701
PAGE 19
REMOTE CONTROL KEY FUNCTIONS (FOR TYPICAL ANALOG TV)
Note: Pressing TV puts remote into TV operating mode
A list of the keys on your remote and what they do in TV mode,
see previous page for remote key functions in the other operating modes
PRG (PROGRAM)
Programs your remote to operate
other products.
See page 13.
FLASHBK (FLASHBACK)
Return to the last channel
viewed.
SURF
Press to turn Surf channel scan
on and off for channel scanning
using Channel Up/Down.
On=Only Surf channels appear.
Off=Normal channel scan.
POWER
Turns TV On or Off.
POWER
PRG
CABLE
VCR
AUX
TV
MUTE
FLASHBK
SURF
VOLUME
VOLUME LEFT / RIGHT
Adjusts the sound level.
CHANNEL
CHANNEL UP / DOWN
Tunes next available channel.
1
2
3
4
5
6
7
8
9
0
MENU
Shows on-screen menus.
PIP
PIP FEATURES
For PIP (Picture-in-Picture)
operation.
ENTER
Shows the Channel/Time display.
QUIT
pip ch
RECORD
NUMBER KEYPAD
Selects channels directly and enters
numeric values for some options.
ENTER
MENU
(MENU) LEFT / RIGHT
DIRECTIONAL ARROWS
The Left/Right directional arrows
adjust menu options.
CC
FREEZ
PAUSE
TV/VCR
SOURCE
TIMER
PLAY
REWIND
FFWD
STOP
TIMER
Displays the Sleep Timer Menu.
Chooses AM/PM on some
equipment
Keys dedicated to VCR functions
will still operate your VCR while
the remote is in TV mode.
CABLE / VCR / AUX / TV
Selects remote operating mode.
MUTE
Turns sound Off and On
while the picture remains.
CHANNEL
VOLUME
LED INDICATOR LIGHT
Lights when keys are pressed.
(MENU) UP / DOWN
DIRECTIONAL ARROWS
The Up/Down directional arrows
select menu options.
QUIT/
Removes on-screen menu/display
from view. With no menus shown onscreen, turns front surround sound
on and off.
CLOSED CAPTIONS
Selects Off, On, or EZ Mute.
TV / VCR SOURCE
Switches between watching TV
through antenna/cable, or one of the
video sources.
remote control part number
MBR3458CT
(124-233-06)
PAGE 20
206-3701
ON-SCREEN MENUS AND DISPLAYS
AVAILABLE MENUS
These are the Main Menus available:
Source Menu, Setup Menu, and Video Menu. There is also a
Source/Time Display.
Source Menu - selects the picture source for the PRO895X:
Video, S-Video, or RGB.
Setup Menu - sets up the PRO895X features.
Video Menu - modifies video options for personal preference viewing.
Source/Time Display - checks Current Source, Signal
Standard, and Time if the clock is set.
BASIC MENU OPERATION (Selecting and Adjusting Menu Features)
Press TV on remote control. Point remote at screen. Press MENU to show the main menu on-screen. Press MENU repeatedly to sequence through the available menus, press ENTER to select a menu when it is highlighted. Use the
Up/Down/Left/Right arrows to select and adjust or change the options, press ENTER when required as shown on the
menu. Press QUIT to remove menus from screen, or wait a short period of time and the menu will disappear by itself.
Other Main Menus available
Selected Main Menu
Source/Time Display
MAIN MENU SELECTIONS
Selected feature
Typical PRO895X Screen
Other available feature
Shows current status of
selected option.
In this case, S-Video source.
Current Source:
S-Video
Press
to Select Input
Press ENTER to change.
Press MENU to show the main
menu on the screen.
POWER
PRG
CABLE
ENTER
VCR
SURF
AUX
TV
FLASHBK
MUTE
CHANNEL
VOLUME
VOLUME
CHANNEL
1
2
4
5
7
8
0
MENU
QUIT
3
6
9
ENTER
QUIT
MENU
PIP
RECORD
SWAP
FREEZ
PAUSE
TIMER
CC
TV/VCR
SOURCE
PLAY
REWIND
FFWD
STOP
On-screen menu operation keys.
Note: Some menus use numbers,
use the number keypad where
required.
206-3701
Note: Some menus include an Exit icon. Use the
Up/Down/Left/Right arrows to highlight EXIT, then
press ENTER.
PAGE 21
SOURCE MENU
AVAILABLE MENU OPTIONS
Use to select video source. There are three menu options available: Video, S-Video, and RGB.
Video
Displays image from composite video equipment connected to
the Video input jack.
S-Video
Displays image from S-Video equipment connected to the
S-Video input jack.
RGB
Displays image from equipment connected to the R, G, B, H/V
Sync and V Sync input jacks.
Notes:
• The PRO895X does not provide any sound (Audio) for equipment
connected to it. Connect equipment like a VCR or DVD Player to a
separate audio output source.
• “Switcher” units are also commercially available that can be used
to connect additional video sources to the PRO895X.
CHANGING INPUT SOURCE
Press TV. Point remote at PRO895X screen. Press MENU repeatedly to highlight the Source menu icon, press ENTER. Use the
Up/Down arrows to select the desired source rectangle: Video,
S-Video, or RGB, press ENTER to got to the newly selected
source.
The PRO895X will then switch to the newly selected video
source, whose image will appear on the PRO895X screen.
Current Source: Video
Press
to Select Input
Press ENTER to change.
Current Source: RGB
Press
to Select Input
Press ENTER to change.
Current Source: S-Video
Press
to Select Input
Press ENTER to change.
S-Video Source Selected
RGB Source Selected
INPUT SOURCES
The above descriptions for input sources refer to the equipment connected to these input jacks on the PRO895X connection panel.
S-Video
Y-C Source
Connector
PAGE 22
Composite
Video
Source
Connector
RGB
Source
Connectors
206-3701
SETUP MENU
Use the Setup Menu to fine-tune the PRO895X to your personal preferences and video sources’ particular requirements
Setup Menu with Timer Setup Selected
Submenu for Timer Setup Option
SETUP MENU OPTIONS
Note: See the following pages for more detailed descriptions of the options listed below.
Clock Set
Sets the PRO895X internal clock.
Timer Setup
Sets up the timer for the PRO895X to turn On and Off at
preset times.
Note: Timer Setup only appears if the clock has been set.
Language
Chooses English, Spanish, French, or German for on-screen
menus.
Video Mode
Selects signal broadcast standard when a Video or
S-Video source is selected.
206-3275-A
Aspect Ratio (Picture Proportion)
Changes shape into which image is projected.
Format Pref (Preference)
Switches between factory setups and customer setups for
certain input formats.
Label Format
Identifies Source’s Format.
Blank Setup
Adjusts blanking on Left/Right/Top/Bottom and Horizontal
and Vertical Center of video image.
Static Setup
Adjusts red and blue over green color convergence alignment in the center of video image.
PAGE 23
SETUP MENU
Clock Set
To set the time on the clock, press MENU repeatedly until the Setup
menu is highlighted. Use the Up/Down arrow to select Clock Set.
Use the Left/Right arrows, or the number keypad as required to set
the current time, to set AM/PM use the TIMER key.
Timer Setup (Timer Menu only appears if clock is set)
Set On/Off Time
The On/Off Timer can be programmed with up to 4 turn-on times
and up to 4 turn-off times. Use the same method to set the Timer
that was used to set the clock.
Example Typical Timer Daily Commercial Usage Setup
Program the PRO895X to turn itself On at the beginning of the
work day, 9:00 am. When the staff goes to lunch at 12:00 pm, set
it to turn Off until they return.
Program the PRO895X to remain On until 5:00 pm. After dinner, set
the PRO895X to turn On and remains On until 10:00 pm. The
On/Off Timer could also be disabled Friday afternoon for the weekend and enabled Monday morning, ready for the next work week.
Enable/Disable On/Off Timer
Retains, but temporarily disables On/Off Timer settings. For example, you may want to enable the On/Off Timer Monday - Friday, but
disable the On/Off Timer Saturday and Sunday. When you return on
Monday you would then enable the On/Off Timer.
PAGE 24
9:00 AM
206-3701
SETUP MENU
Language
Chooses English, Spanish, French, or German for the
PRO895X on-screen menus. Once you select a new
language, the on-screen menus will appear in that language.
Note: The word Language always appears in English.
Video Mode
Selects broadcast signal standard. You can change the signal standard manually or have it selected automatically.
The following are signal standards for the U.S.A. and other
countries.
Manual Modes
M-NTSC, M-PAL, N-PAL, BG-PAL, NTSC 4.43
Automatic Modes
Americas’ standards —
Auto: M-PAL/N-PAL/NTSC
Europe’s standards — Auto: BG-PAL/NTSC
Broadcast Standards/Geographical Area
M-NTSC —
U.S.A., Canada, and Mexico
M-PAL —
South America
N-PAL —
South America
BG-PAL —
Europe, China
NTSC 4.43—
Europe
Note: If you select one of the Automatic modes for your country,
the PRO895X selects the broadcast standard from among those
shown.
Aspect Ratio (Picture Proportion)
Use to change the shape into which the source’s image is
projected. If the projected image from a particular source
appears distorted, then you have the option to select a
different aspect ratio for that source.
One or more of the video sources may have a different
aspect ratio than other video sources. In this case, change
the Aspect Ratio to the appropriate configuration for the
video source’s image.
Preset Image Aspect Modes
4 x 3 — Standard TV/VCR picture proportion.
Letterbox — 4 x 3 picture proportion with the top and
bottom screen blanked out to form a 16 x 9 image. This
mode can be used with certain laser discs in this signal
format.
16 x 9 — 16 x 9 picture dimension is used by digital
video disc players and certain other wide screen formats.
Compressed — 16 x 9 picture dimension with a 4 x 3
video image in the center of the screen. Left and Right
sides are are filled with gray level video referred to as Side
Panels. Useful when watching normal VCR output on a
16 x 9 screen. (Available with Video and S-Video only.)
Compressed Image Adjustable Side Panels
Black to White Adjustment
From the Setup Menu, select the Aspect Ratio option.
Select Compressed as the Aspect Ratio.
In the Video Menu, select the Side Panel darkness you prefer, from the blackest black, (0) to the whitest white,
(100).
206-3701
Custom
Note: The Side Panels option appears on the Video Menu only if
Compressed is selected as the Aspect Ratio on the Setup Menu.
PAGE 25
SETUP MENU
Format Pref (Preference)
Switches between factory setups and customer-defined setups for those formats pre-aligned at the factory.
Available Format Preferences
Preset 10 Formats
Preset factory-aligned settings
formats. (Not adjustable.)
Custom 10 Formats
Customer-aligned settings of
standard Preset factory-aligned
formats.
Customer 5 Formats
Customer defined formats and
customer aligned setup
settings.
Note: Use Status on-screen display to identify current format.
See “On-Screen Menus and Displays section.”
New Formats, Not Recognized by the PRO895X
When you hook up a new video source whose unique signal “format” is not recognized by the PRO895X (the new
video source may have video characteristics that are not
“preset” as one of the 10 formats by the factory), the
Label Format
Identifies the format used on video image source.
Personalize the video source format by assigning a name
to identify the format used on each video input source.
Example of format labels: DVD, VCR 1, MAC II.
PRO895X will ask if you would like to save those settings
as a new format. You can use one of the 5 Customer format slots available, which are not preset at the factory.
Typical Format Titles: VGA300, VGA350, VGA480.
After you store the new format (when the new video
source becomes the source of the image on the PRO895X
screen), the PRO895X remembers and defaults to that setting when you choose that new video source as the image
source.
New Formats, Recognized by the PRO895X
The newly connected video source’s format will probably
be recognized as one of the 10 PRO895X “Preset” factory
aligned settings. If you wish to change any of those settings, like Contrast or Tint, the factory “Preset” aligned
settings format becomes a “Custom” format (with user
defined settings). The PRO895X defaults to the “Custom”
Format Pref (Preference) when you choose the new video
source as the image source.
Source
Video In
S-Video
RGB
Blank Setup
This setup should be preset by system installer.
Occasionally if you connect a new video source to the
PRO895X, the video Blanking and the V and H Phase may
require adjustment.
Blanking Top/Left
Covers up undesirable
images such as these:
Blanking — “covers up” undesirable images at the
extreme edges of the picture.
Phase — moves the scene or picture
(Up/Left/Down/Right) within the projected image area.
Phase
Centers Image.
Blanking Bottom/Right
Covers up undesirable
images around edges
such as these:
PAGE 26
Format
DVD — A DVD player is connected to
the Video Input jack and the
format used is named DVD.
VCR 1 — An S-Video VCR is connected to
the S-Video input jack and the format
used is named VCR 1.
MAC II — A computer is connected to
the RGB input jacks and the format used
is named MAC II.
Projected Image Area
Note: Picture shown is not
centered, it is too far
down and to the right.
Continued on next page
206-3275-A
SETUP MENU
Blank Setup (Continued)
Separate menus are available for adjusting the Top/Left and
Bottom/Right of the projected image as well as the Phase.
To adjust any option, see page 21 for basic menu operation.
(Blank Setup is normally adjusted by the installation
technician; usually no additional changes are needed.)
Notes:
• If you make changes to any option, you will be asked to save
them to the currently selected format. If the format is unknown,
store it as a new customer format.
Press MENU for next adjustment.
Press
to change setting.
Static Setup (Red, Blue, Green Convergence)
Occasionally the red, blue, and green images go out of
convergence. In the Static Setup Menu you will see a menu
similar to the one shown at the right. Ideally, the convergence is correct when the bars in the center of the menu
are white.
Adjusting Convergence
Use the Up/Down/Left/Right arrows to converge Red and
Blue. You want to adjust each color so that the center area
of the bars is white. With the highlight on either the
Adjusting Red or Adjusting Blue rectangle, press MENU.
Move the color using the Up/Down/Left/Right arrows to
align the color to the center of the bars. The green does
not move; you are moving the Red and Blue over the green.
When the bars are white, the convergence re-alignment is
complete. Press QUIT to leave the menu.
Confirming Your Menu Changes
As indicated on the confirmation menu, press ENTER to
confirm your changes and save them.
206-3275-A
Use Arrows to Converge Red
Press MENU to Switch to Blue
PAGE 27
VIDEO MENU
ADJUSTMENTS
Fine-tune settings for each video source. You can make
changes to each option by moving the highlight to the
desired option (Contrast, Brightness, Color, etc.) to select
it. Once the option is selected, you can make changes by
pressing the Left or Right directional arrows to change the
option settings.
For example, with the highlight on the Contrast option,
press and hold the Right arrow to increase the contrast.
Or, press and hold the Left arrow to decrease the contrast.
Some options only offer either an On or Off choice or a
fixed range of choices; see descriptions below.
The option changes will be reflected in the lower portion
of the menu in the Option Status Display rectangle.
Press QUIT to exit the Video menu, save the changes.
Note: You may set the Video Menu options independently for
each video source format.
Custom
VIDEO MENU OPTIONS
Adjustment
Contrast
Brightness
Color*
Tint*
Sharpness*
Color Temp
Red Level
Green Level
Blue Level
Video Filter*
Auto Flesh*
Picture Pref.
(Preference)
Gamma
Corr.
Video menu if Color Temp is set to Custom.
Adjustment Options or Range and Effect
(0-100) Adjusts the overall light to dark characteristics of the picture.
(0-100) Adjusts the brilliance of the picture from very dim to very bright.
(0-100) Adjusts the intensity of the colors in the picture.
(0-100) Adjusts the flesh tones to more green or red.
(0-100) Adjusts the clarity of the edges around objects for the clearest picture quality.
(Custom- Red Level, Green Level, Blue Level/3200K/6500K/9300K) Changes the color “temperature”
or picture white balance between cooler natural whites and warmer red colors. There are three preset
color temperatures and one custom setting. When the custom setting is selected, three options to
set the relative red level, green level, and blue level appear. These settings define your customized
color temperature.
(Off/Low/Medium/High) Reduces video noise or interference in the dark picture areas resulting in a
clearer overall picture.
(Enabled/Disabled) Maintains natural skin tones in changing scenes and video source conditions.
(Custom/Preset/Theater) Lets you use your own Custom video settings, the factory preset video settings
or the factory preset theater video settings. The theater settings are preset to provide optimum
visual performance in low-light “theater-like” conditions.
(Off/Low/Medium/High) The Gamma Correction option limits the intensity of the peak whites. Use as
the starting point for Gain change. Limit how high the peak whites will get to prevent defocusing and
loss of shape or definition.
*These options will not be available when RGB is the selected picture source. Note: Any changes to the above when Picture Pref. is in
the Preset or Theater modes will automatically make the current settings your new custom settings.
PAGE 28
206-3701
VIDEO MENU
RGB Source Special Adjustments
(Normally adjusted by the installation technician; usually
no additional changes are needed.)
For the RGB Source only, the Clamp Pulse is set at Auto
Select by the factory.
image is “splotchy,” When the image is too green, or when
the image is too dark.
Auto Select determines the pulse of the RGB input video
source and automatically chooses the appropriate setting.
If you change the equipment connected to the input jack
of the RGB video source, adjust the Clamp Pulse for the
new RGB video source. Set at Auto Select, Back Porch, or
Sync Tip, whichever produces the best image and minimizes signal degradation.
Adjustment to the Clamp Pulse may be necessary under
certain conditions: When an erroneous background color is
being produced by extremely wide horizontal signal pulses,
When the image is accompanied by “banding,” When the
Adjustment
Clamp Pulse,
Sync Inputs
Sync Mode
206-3275-A
The Clamp Pulse is initially set to Auto Select. You can
choose to set it at Back Porch or at Sync Tip.
Adjustment Options or Range and Effect
Sets the position of the clamping signal for the video. The options are to clamp on the Back Porch or
the Sync Tip, or to Auto Select between the two based on the format input.
Determines if a 75 ohm termination should be made to the H Sync and V Sync inputs. The options are
either Terminated or Not Terminated.
Selects a special type of studio composite sync when such a signal source is used on the H Sync input.
The default setting is for Normal Analog/TTL. Switch to Special Composite when using the studio
sync source.
PAGE 29
MAINTENANCE AND TROUBLESHOOTING
CARING FOR YOUR HD PROJECTION DISPLAY
Your HD Projection Display will look better, have a longer
life and perform better if you care for it properly.
Moisten the soft cloth or tissue with warm water and gently wipe the surface of the lens.
First check to see that the PRO895X is off. For
added safety, disconnect AC power to the
PRO895X.
Note: The lenses are easily damaged. Avoid accidental
contact with them.
Note: If you unplug your PRO895X, you will
have to reset the clock to the current time.
EXTENDED ABSENCE
CABINET CARE
Non-Wood Cabinet or Cabinet Components. Moisten a soft
cloth with a mild soap solution. Wipe the surface with a
damp cloth. Then rinse the cloth in clean water and wipe
the surface again. Allow the PRO895X to air-dry before
turning it on.
Before an extended absence (such as a vacation) you may
want to disconnect AC power to your PRO895X. This will
protect the HD Projection Display from possible damage
from lightning or power line surges. For added safety, you
may want to disconnect all video equipment currently connected to the PRO895X.
Note: If you unplug your PRO895X, you will have to reset
the clock to the current time.
LENS CLEANING
When the lenses of your HD Projection Display need cleaning, be sure to follow these directions so you do not damage or scratch the optical coating on the lenses:
• Do NOT spray any type of fluid directly on
the lenses’ surface.
• Use a soft cotton cloth (cotton diapers
laundered several times to remove sizing) or a
soft facial tissue.
• Do NOT use any type of aerosol cleaner.
PICTURE INTERFERENCE
Your picture may be affected by interference caused by one
or a number of factors, including:
Speckled or Streaked Picture - Can be caused by nearby
automobile ignition, electrical appliances, etc. This is most
noticeable when there are loose connections to the unit.
Snow in Picture - Caused by insufficient signal - possibly
when the video cable is too long or broken, or has an
intermittent ground return.
• Do NOT use dry material, such as paper,
tissue or a dry cloth to clean the lenses.
PAGE 30
206-3275-A
MAINTENANCE AND TROUBLESHOOTING
BEFORE CALLING FOR SERVICE
Use the following chart to identify operating problems. You may save a service call charge if the problem can be
identified as a simple switch set improperly.
Note: Problems not listed here may be installation related, see Installation Guide. Refer problem to Installer/Maintenance personnel.
PROBLEM IDENTIFICATION CHART
Problem
Possible Cause
No image on screen.
Source turned off? No signal? Weak signal? Cables loose or broken?
Remote does not work
on screen menus.
Using wrong remote control? Use only Universal remote. Remote in wrong mode? Batteries
weak? Wrong battery polarity? Remote not pointed at PRO895X screen? Wrong source
selected?
Colors misaligned.
Format wrong for current source selected? Static Setup needs adjustment?
Image appears distorted. Aspect Ratio setup wrong for source selected?
Image appears in black
and white.
Wrong broadcast standard selected? Black and white signal? Weak signal from broadcasting
station? Cables broken or loose?
VCR cannot be
controlled.
Remote in TV mode? Remote not pointed at VCR? VCR cannot be controlled by remote?
Remote batteries weak? Did you use AutoFind option to program remote for VCR? VCR not IR
controlled? VCR turned off? VCR in Timer mode?
Sleep Timer does not
function.
Sleep Timer status set to Off?
PRO895X turns off.
Sleep Timer turned On? Off Timer active? Power failure?
PRO895X does not
turn Off at preset time.
On/Off Timer disabled?
Aspect Ratio, Format
Stable incoming signal is not available on selected source, or signal format is not in a
Pref, Label Format
format recognized by the PRO895X.
and Blank Setup options No equipment connected to selected source.
are not available on
Setup Menu.
Image looks
“Washed Out.”
Loop Out/In switch set on wrong position?
RGB SOURCE PROBLEMS
Problem
Possible Cause
Video mode not available Video mode only available on Video or S-Video Source.
on Setup Menu.
Image
Image
Image
Image
206-3701
is too green.
has “banding”
is “splotchy.”
is too dark.
Clamp Pulse may need adjustment.
PAGE 31
Your Zenith PRO895X HD Projection Display Warranty
HD Projection Monitor
Welcome to the Zenith family! We believe that you will be pleased with your new Zenith PRO895X. Please read this warranty carefully,
it is a “ONE-YEAR LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights
that vary from state-to-state within the U.S.A.
ZENITH’S RESPONSIBILITY
Service Labor
Parts
On-Site Service
Not Covered
During a period of one-year from effective warranty date, Zenith will provide service labor by a Zenith authorized Pro A/V service center
when needed, as determined by the Zenith authorized Pro A/V service center, as a result of manufacturing defects.
New or remanufactured replacements for factory-defective parts will be supplied by a Zenith authorized Pro A/V service center for one-year
from effective warranty date. Such replacement parts are warranted for the remaining portion of the original warranty period.
Whenever possible, warranty service will be provided where the PRO895X is installed in the U.S.A. or Canada. (Some repairs may require the
PRO895X to be taken by the servicer to the repair facility and returned, at no additional charge. The HD Display must be taken down from the
ceiling for on-site service. Zenith or Zenith Service Centers are not responsible for de-installation or re-installation.)
This warranty covers manufacturing defects and does not cover installation, adjustment of controls, or repair of home systems, cable converters
or cable company-supplied equipment: it does not cover damage due to misuse, abuse, negligence, acts of God, or causes beyond the control of
Zenith. Any alteration of the product after manufacture voids this warranty in its entirety.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
OWNER’S RESPONSIBILITY
Effective Warranty Date
Operating Guide
Important
Warranty Service
Warranty begins on the date of original installation. For your convenience, keep the dated bill of sale or delivery ticket
as evidence of the purchase date.
Read your Operating Guide carefully so that you will understand the operation of your PRO895X and how to adjust the customer controls.
Product Registration—Please fill out and mail your Product Registration Card. It is imperative that Zenith know how to reach
you promptly if we should discover a safety problem that could affect you.
For warranty service information, call 1-888-865-3026. Parts and service that are Zenith’s responsibility (see above) will be provided without
charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call or write the Zenith
Information Center. You must provide the model number, serial number and date of purchase or date of original installation. Before you ask for warranty service, read “Maintenance And Troubleshooting” in your operating guide. You might avoid a service call.
ZENITH ELECTRONICS CORPORATION
Customer Information Center
201 James Record Rd., Building 3
Huntsville, AL 35824
For 24-hour customer service call:
1-888-865-3026
www.zenith.com
PRO895X/2001
© Copyright 2001 Zenith Electronics Corporation
206-3701
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising