CYBEX | Plate Loaded 16120 Smith Press | Cybex® Plate Loaded 16120 Smith Press Owner`s

Cybex® Plate Loaded 16120 Smith Press Owner`s
Cybex® Plate Loaded 16120 Smith Press
Owner’s Manual
Strength Systems
Part Number 16120-999-4 F
www.cybexintl.com
Table of Contents
Safety
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines and Practices . . . . . . . . . . . . . 4
Warning/Caution Decals . . . . . . . . . . . . . . . . . . . 6
Regular Maintenance Activities . . . . . . . . . . . . . . 8
Exercise
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Customer Service
Contacting Service . . . . . . . . . . . . . . . . . . . . . . . 11
Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Return Material Authorization (RMA) . . . . . . . . . 12
Damaged Parts . . . . . . . . . . . . . . . . . . . . . . . . . 13
Assembly
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance
Daily Procedures . . . . . . . . . . . . . . . . . . . . . . . . 21
Weekly Procedures . . . . . . . . . . . . . . . . . . . . . . 21
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2011, Cybex International, Inc. All rights reserved.
Printed in the United States of America. 10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexintl.com • techhelp@cybexintl.com • 16120-999-4 F
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Safety
Safety
Read the Owner’s Manual carefully before assembling, servicing or using Cybex equipment.
WARNING: Serious injury could occur if these safety precautions are not observed:
User Safety Precautions
•
Obtain a medical exam before beginning any exercise program.
•
Stop exercising if feeling faint, dizzy or experiencing pain and consult your physician.
•
Obtain instructions before using.
•
Read and understand the owner’s manual and all warnings posted on the machine before using. •
Keep all children (12 and under) away. Teenagers (13 and over) and disabled must be supervised.
•
Use a spotter.
•
Keep body and clothing free from and clear of all moving parts.
•
Use the machine only for the intended use. DO NOT modify the machine.
•
Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
•
DO NOT attempt to fix a broken or jammed machine.
•
Report any malfunctions, damage or repairs to the facility.
•
Replace any warning labels if damaged, worn or illegible.
Facility Safety Precautions
•
Read the Owner’s Manual carefully before assembling, servicing or using this equipment.
•
ake sure that each machine is set up and operated on a solid level surface. Do not install
M
equipment on an uneven surface.
CAUTION: Cybex is not responsible for the actual anchoring of equipment. Consult with
a professional contractor.
3
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
WARNING: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8’’ grade 2 bolts or better).
WARNING: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim
any leg or frame not in contact with surface using flat washers.
•
Make sure that all users are properly trained on how to use this equipment.
•
Make sure there is enough room for safe access and operation of this equipment.
•
erform regular maintenance checks on this equipment. Also pay close attention to
P
all areas most susceptible to wear.
•
Immediately replace worn or damaged components. If unable to immediately replace worn or
damaged components then remove from service until the repair is made.
•
It is the sole responsibility of the user/owner or facility operator to ensure that regular
maintenance is performed.
Safety Guidelines and Practices
Cybex recommends that all fitness equipment be used in a supervised area. It is recommended that
the equipment be located in an access controlled area. Control is the responsibility of the owner. The
extent of control is at the discretion of the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s
manual, and warning labels; as well as instruct all individuals, whether end users or supervising
personnel, on proper usage of the equipment.
PROPER USAGE:
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine
is at rest or in use. Inappropriate or improper use may result in injury to users or third parties
(bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure
that the facility has the proper clearance for usage and training.
4
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
SECURING EQUIPMENT:
The machine has holes in the feet, which allow for ease in anchoring to the floor. Cybex strongly
recommends that, to eliminate rocking, tipping or falling over due to incorrect usage and misuse,
equipment be secured to a solid, level surface.
1. T
he solid, level surface should not deviate more than 1/8” over a 10’ distance or as defined and
required by local building and architectural codes.
2. Anchoring of equipment must be completed by a qualified licensed contractor.
3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when used when anchoring the equipment to the floor.
4. Due to the wide variation of flooring on which machines may be anchored or installed, verify
anchoring method and anchoring fasteners with a qualified and licensed contractor.
5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position.
6. Do not use machine until it is properly anchored.
MAINTENANCE:
Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform
the maintenance requirements as specified in the manual.
STANDARD COMPLIANCE:
Cybex products meet or exceed applicable ASTM and EN Standards.
5
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Warning/Caution Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death
or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor
or moderate injury.
The following diagram shows where each decal is located.
Smith Press - 16120
B
A
B
C
B
D
B
C
C
C
Description Part No.
A. Warning Decal..............5220-364-4
B. Warning Decal..............16120-340-4
C. Warning Decal..............16120-341-4
D. Caution Decal...............4000Y316-4
6
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
A
WARNING
3.25
SERIOUS INJURY
B
R .19
4 PLACES
COULD OCCUR IF
THESE PRECAUTIONS
ARE NOTWARNING
OBSERVED
SAFETY ORANGE PMS152
BLACK TRIANGLE W/ ORANGE
EXCLAMATION POINT, BLACK LETTERS
32 PT ARIAL BOLD
1. Obtain a medical exam
INSET .06
before beginning any
WHITE
exercise program.
2. StopUNHOOKED
exercising if feeling
WHITE BACKGROUND WITH
HOOKED
BLACK 14 PT ARIAL BOLD
faint, dizzy or
RED CIRCLE WITH LINE THROUGH
Serious injury can result if
experiencing
and
bar catch is pain
not hooked
consult
your
properly
andphysician.
falls.
8.00 3. Obtain
Makeinstructions
sure bar catch is fully
before
using.
Lisez
engaged
over
hook les
to avoid
injury.
instructions
avant
I’untilisation.
SAFETY ORANGE PMS152 2.50
4. Read and understand the
R .19
BLACK TRIANGLE W/ ORANGE
4 PLACES
owner’s manual and all
EXCLAMATION POINT, BLACK LETTERS
32 PT ARIAL BOLD
SAFETY YELLOW PMS 108
warnings posted on the
BACKGROUND. BLACK TRIANGLE
Seriousbefore
injury or
death may
machine
using.
W/ YELLOW EXCLAMATION POINT,
result if the adjustable bar
BLACK LETTERS 26 PT ARIAL
5. Keep
all children
and
stops
are not set (12
properly.
WHITE BACKGROUND WITH
BOLD FONT
under) away. Teenagers
1.50BLACK 14Personal
PT ARIAL BOLD
injury may occur.
INSET .06
DO
NOT
start
an
(13 and over) and disabled
WHITE
exercise
unless
Keep away from moving
must
be supervised.
WHITE BACKGROUND WITH
adjustable bar
parts to avoid injury.
Garder
BLACK 11.5 PT ARIAL BOLD TEXT
stops tous
are in les enfants
4000Y316-4 A
(deplace.
12 ans et moins)
PART NUMBER
éloignés. Les adolescents
6 PT ARIAL BOLD
PART NUMBER
3.25
useplus)
of adjustable
(de PROPER
13 ans et
et les
6 PT ARIAL
.19 allow an immediate
barRstops
handicapés
doivent être
EXCEPT AS NOTED
4 in
PLACES
exit
case
of
accident
or
surveillés.
DIMENSIONS
OWATONNA
REMOVE ALL BURRS
emergency.
BREAK SHARP EDGES
IN INCHES
.005/.010 R
GENERAL
6. Use a spotter.
DECAL, WARNING
TOLERANCES:
SURFACE FINISH
SAFETY ORANGE PMS152
ALL MATERIAL MUST COMPLY TO
ENGLISH
INDICATED PER
2 DECIMALS ± .03
EUROPEAN UNION DIRECTIVE
7. Keep body
and
clothing
ANSI B46.1-1985
3 DECIMALS ± .015
2002/95/EC RoHS (RESTRICTION
BLACK
TRIANGLE
W/ ORANGE
NOTE: See Engineering Drawing
16120-340-X
for material
specifications.
OF HAZARDOUS SUBSTANCES)
ANGLES ± 1°
REMOVE CARBURIZATION
4-9-09
REL
free from
and clear of
EXCLAMATION
POINT, BLACK LETTERS
AND SCALE FROM LASER
FEATURES SHOWN
AND PLASMA CUT EDGES
4-13-09
BB
PERPENDICULAR OR
32 PT
ARIAL BOLD
all moving
parts.
125
GENERAL
PARALLEL SHALL BE
SO WITHIN ± 1°
MACHINING
B 1:1
16120-340-4
B
1 1
8. Use the machine only for
RED PMS 185
or death may resultthe intended use. DO NOT
le bar stops are set modify the machine.
INSET .06 prior to
location when doing
9. Inspect machine
WHITE
CISE.
use. DO NOT use if it
MATERIAL:
appears damaged or
CISE
inoperable.
THIS NOTE REFERS TO ALL PLASTIC PARTS
able
10. DO NOT attempt to fix
AND ASSEMBLIES CONTAINING PLASTICS.
in
a brokenPMS
or jammed
RAW MATERIAL AND COMPONENTS ON
108
YELLOW
NOTE:
See Engineering Drawing 4000Y316-X for specifications.
SUB-ASSEMBLIES AND ASSEMBLIES MUST
machine.
COMPLY WITH EUROPEAN DIRECTIVE
RoHS 2002/95/EC.
11. Report any malfunctions,
ement of adjustable
FINISH:
w an immediate exit damage or repairs to the
ident or emergency. facility.
16120-341-4 B
12. Replace any warning
labelsPART
if damaged,
worn
NUMBER
or illegible.
6 PT ARIAL
UND WITH
5220-364-4 A
L BOLD
Specs
Master
Artwork
D
WARNING
CAUTION
CAUTION
Master Artwork
pecs
Keep away from moving
parts to avoid injury.
4000Y316-4 A
Master
Artwork
MATERIAL:
TITLE:
16120-340-4 B
ARNING
Personal injury may occur.
FINISH:
DWG. BY
DATE
TECH. PUBS. APPR.
DATE
CHECKED BY
DATE
MFG. APPR.
DATE
SIZE
SCALE
SHEET
REV.
DWG. NO.
OF
C
EXCEPT AS NOTED
DIMENSIONS
IN INCHES
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
awing 16120-340-X for material specifications.
RIAL MUST COMPLY TO
N UNION DIRECTIVE
C RoHS (RESTRICTION
DOUS SUBSTANCES)
EXCEPT AS NOTED
MATERIAL:
DIMENSIONS
IN INCHES
EXCEPT AS NOTED
DIMENSIONS
REMOVE ALL
BURRS
IN INCHES
BREAK SHARP
EDGES
GENERAL
.005/.010 R
TOLERANCES:
GENERAL
ALL MATERIAL MUST COMPLY TO
2 DECIMALS ± .03
UNION DIRECTIVE
TOLERANCES:EUROPEAN
SURFACE3 FINISH
DECIMALS ± .015
2002/95/EC RoHS (RESTRICTION
OF HAZARDOUS SUBSTANCES)
ANGLES
INDICATED
PER± 1°
2 DECIMALS ± .03
FEATURES SHOWN
FINISH:
ANSI
B46.1-1985
PERPENDICULAR OR
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
TITLE:
TITLE:
SURFACE
FINISH
INDICATED PER
ANSI B46.1-1985
DWG. BY
125
DECAL, WARNING
ENGLISH
DECAL,REL/BG
WARNING ENGLISH
DATE
REMOVE CARBURIZATION
AND SCALE FROM LASER
CHECKED BY
AND PLASMA
DWG. BY CUT EDGESDATE
125
GENERAL
SHALL BE
REMOVE PARALLEL
CARBURIZATION
JKW/BG
MACHINING
SO
WITHIN ± 1°
AND SCALE FROM LASER
CHECKED BY
AND PLASMA CUT EDGES
GENERAL
MACHINING
OWATONNA
OWATONNA
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
BB
SIZE
B
SCALE
1
7
OF
SCALE
SHEET
5/5/09
SHEET
1:1
3-10-09
1:1
B4/1/09
1 OF 1
SIZE
DATE
DATE
1
DWG. NO.
TECH. PUBS. APPR.
DATE
MFG. APPR.
DATE
TECH. PUBS. APPR.
DWG. NO.
DATE
BB
16120-341-4
MFG. APPR.
DATE
5220-364-4
5/5/09
B
REV.
REV.
A
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
TITLE:
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
DWG. BY
DATE
TECH. PUBS. APPR.
CHECKED BY
DATE
MFG. APPR.
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
GENERAL
MACHINING
125
DECAL, CAUTION ENG
JKW
SIZE
B
SCALE
1:1
8/28/06
SHEET
1
OF
1
DWG. NO.
BB
4000Y316
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal operation of this
equipment. Keeping a log sheet of all maintenance actions will assist you in staying current with all
preventative maintenance activities.
WARNING: Equipment found to have worn or damage components must be removed
from service until repair(s) is made. Failure to do so could result in injury
Daily
•
Daily upholstery
Weekly
•
Inspect all nuts and bolts for looseness. Tighten as required.
•
Check for worn handles and warning labeling. Replace all worn parts immediately.
8
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Exercise
Intended Use
The intended use of this equipment is to aid or improve general physical fitness and exercise. For
Commercial use.
Instructions
Read and understand all instructions and warnings prior to using this machine. See Chapter 1, Safety
in Owner’s Manual or consult with floor staff.
This machine is very versatile.Exercises that can be performed include: Squats, Bench and
Incline Presses, Bent-Over Rows and Overhead Press.
Bench Press
Squat
9
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Set Up
1. Adjust bar to appropriate height for exercise. See Diagram A.
2. Adjust bar stops to appropriate height for exercise. See Diagram B.
Ensure stops are set properly at equal height.
3. Load bar evenly with appropriate resistance. Unloaded bar weight = 15 pounds (7kg).
Diagram A
Diagram
Movement
Diagram B
A
Diagram B
1. Position yoursalf for the exercise to be performed and grasp bar.
2. Lift bar rotate to release catch. See Diagram A.
3. Lift/lower bar with smooth, controlled movements.
4. L
ock bar by rotating until catch is fully engaged. See Diagram A. Ensure bar catch is fully engaged
over hook before releasing grip on bar.
10
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m Eastern Standard
Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or
fax 508-533-5183.
Find information on the web at www.cybexintl.com or e-mail at techhelp@cybexintl.com
Ordering Parts
Fax orders to 508-533-5183. To speak with a customer service representative, call 888-462-9239
(for customers living within the USA) or 508-533-4300 (for customers outside the USA). You may also
contact us through e-mail at techhelp@cybexintl.com.
CAUTION
Use only Cybex replacement
parts when servicing.
Failure to do so could result
in personal injury.
NOTE: All inspections
and repairs must be
performed by trained
service personnel only.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Having the following information ready when calling, will assist our Cybex representatives in serving
you.
•
Unit Serial Number
•
Product Name
The unit serial number and product name can be found on the serial number decal.
•
Part Description
•
Part Number
11
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Part descriptions and part numbers are located on the web at www.cybexintl.com.
•
Shipping Address
•
Contact Name
In addition to your shipping address and contact name, your account number is helpful but not
required.
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning
material for placement, repair or credit. The system assures that returned materials are properly
handled and analyzed. Follow the following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will
request a RMA from Cybex, if applicable. Under no circumstances will defective parts or equipment
be accepted by Cybex without proper RMA and an Automated Return Service (ARS) label.
•
Call the Customer Service Hot Line listed above for the return of any item that is defective.
•
rovide the technician with a detailed description of the problem you are having or the defect in
P
the item you wish to return.
•
Provide the model and serial number of your Cybex equipment.
•
t Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for
A
evaluation and repair or replacement. The technician will assign you a RMA number and will send
you an ARS label. The ARS label and the RMA numbers must be clearly displayed on the outside
of the package that contains the item(s) to be returned. Include the description of the problem, the
serial number of the equipment and the name and address of the owner in the package along with
the part(s).
•
Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
erchandise returned without an RMA number on the outside of the package or shipments sent COD
M
will not be accepted by the Cybex receiving department.
12
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the
responsibility of the carrier (UPS, Federal Express, trucking companies, etc.)
Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with
a visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will
result in the carriers refusal to honor your damage claim. The carrier will provide you with the required
forms for filing such claims.
Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but notices
later must be reported to the carrier as soon as possible. Upon discovery of the damage, a written
or phone request to the carrier asking them to perform an inspection of the materials must be made
within ten days of the delivery date. Keep all shipping containers and packing materials as they
will be needed in the inspection process. The carrier will provide you with an inspection report and
the necessary forms for filing a concealed damage claim. Concealed damage claim is the carrier’s
responsibility.
13
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
14
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Assembly
Tools Required
•
•
•
•
•
9/16” Socket wrench
7/16” Wrench
7/32” Allen wrench
9/16” Wrench
5/16” Allen wrench
16120 Smith Press
Total Weight and Size
380 lbs.inches - 84 W x 54 L x 84 H
173 kgcm - 213 W x 137 L x 213 H
Three people will be required for this procedure.
It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate
clearance around each machine to allow for safe use and passage.
1. Read and understand all instructions thoroughly before starting any of the procedures listed below.
2. Verify you have received the appropriate configuration.
•
Verify you received the correct color machine that you ordered.
•
Verify you received the appropriate owner’s manual.
•
Verify you received the warranty sheet.
15
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
WARNING: Use extreme caution when removing Smith Press Assembly from pallet. Failure to do so could result in injury.
3. Move to desired location and unpack.
•
Keep all shipping packages near area of installation.
•
Remove hardware pack and verify contents.
A
E
B
C
D
F
G
A. Locknut .375-16 (8), HN704902
B. HHCS .250-20 x 2.00 (2), HC621215
C. SHCS .375-16 X 1.25 (8), JC702821
D. BHSCS .375-16 X2.50 (4),HC700430
E. Split, Lockwasher .375 (8), HS348300
F. Foot Pad (6), 16010-311
G. Loctite 242 (1) YA000008
•
Carefully remove foam and shrink wrap securing frame mounts, set frame mounts aside.
•
Carefully remove foam and shrink wrap securing weight bar to frame, set weight bar aside.
•
sing a 7/32” Allen wrench and a 9/16” wrench remove the four Button Head Socket Cap Screws U
(BHSCS) from shipping bracket securing frame halves together. Do not discard BHSCS or locknuts.
•
Using a 9/16” wrench remove the four lag bolts securing frame to pallet.
16
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
4. Assemble Frame
•
With assistants hold frames in an upright position.
•
Carefully place foot pad (supplied with machine) on each foot of the frame.
•
Align front frame mount in place.
Locknut (Qty of 2 each side)
BHSCS
(Qty of 2 each side)
Front Frame Mount
•
Using a 7/32” Allen wrench and a 9/16” wrench secure front frame mount in place with the four
BHSCS and locknuts removed in step 3.
•
Place back frame mount in position. Using a 7/32” Allen wrench and a 9/16” secure back frame
mount to frame with the four BHSCS and locknuts from shipping package.
Locknut (Qty of 2 each side)
Back Frame Mount
BHSCS (Qty of 2
both sides)
Locknut
17
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
5. Install weight bar assembly.
•
Carefully place weight bar on frame and secure in place by latching bar catch on hooks.
•
Verify each bar catch is hooked properly on the hook.
Hook
Bar Catch
Weight Bar
•
Slide bearing housing up (located at bottom of guide shaft) and align holes with weight bar
bracket. •
Locate four Socket Head Cap Screws (SHCS), four washers and loctite from shipping package.
•
Place a small drop of loctite on the four SHCS and in threaded holes of weight bar bracket.
•
Place washer over SHCS.
•
Using a 5/16” Allen wrench tighten the four SHCS securing the weight bar bracket to the bearing housing.
•
Repeat step 5 for opposite side.
SHCS (Qty 4)
Guide Shaft
Bearing Housing
Loctite
Washers
(Qty 4)
Weight Bar Bracket
18
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
6. Cable Installation.
•
Locate two Hex Head Cap Screw HHCS from shipping package.
•
Place a small drop of loctite on HHCS and in threaded hole.
•
sing a 7/16” wrench, attach cable end to weight bar bracket with HHCS. Cable end must U
be attached straight to avoid a kink in cable.
•
Repeat step 6 for opposite cable end.
Weight Bar Bracket
Cable
Cable
End
Cable end must be attached
straight to avoid kink in cable.
HHCS
7. Securely anchor machine to the floor using the anchor holes provided in each machine.
CAUTION: Cybex is not responsible for the actual anchoring of equipment. Consult with
a professional contractor.
WARNING: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8’’ grade 2 bolts or better).
WARNING: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim
any leg or frame not in contact with surface using flat washers.
8. Verify proper operation.
19
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
20
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
Maintenance
All preventive maintenance activities must be performed on a regular basis. Performing routine
preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength
Systems equipment.
Cybex is not responsible for performing regular inspection and maintenance actions for your
machines. Instruct all personnel in equipment inspection and maintenance actions and also in
accident reporting/recording. Cybex phone representatives are available to answer any questions or
concerns that you have.
CAUTION
Use only Cybex replacement
parts when servicing.
Failure to do so could result
in personal injury.
NOTE: All inspections
and repairs must be
performed by trained
service personnel only.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Daily Procedures
•
Upholstery - Wipe down all upholstery.
•
Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equipment.
•
Chrome - Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral cleaners with a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equipment.
Weekly Procedures
•
Inspect all nuts and bots for looseness. Tighten as required.
•
Inspect all labeling for readability. This includes instructional placards, warning and caution
decals. Replace all worn labeling immediately.
21
Cybex Plate Loaded 16120 Smith Press Owner’s Manual
22
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexintl.com • techhelp@cybexintl.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising