American Megatrends | MI941 | User`s manual | American Megatrends MI941 User`s manual

American Megatrends MI941 User`s manual
MI941
LGA775 Core™ 2 Duo
Intel® G41 Chipset
Mini-ITX Motherboard
USER’S MANUAL
Version 1.0A
Acknowledgments
AMI is a registered trademark of American Megatrends, Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel is a trademark or registered trademark of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
Table of Contents
Introduction ....................................................... 1
Checklist .............................................................................. 1
Product Description ............................................................. 2
Specifications ...................................................................... 3
Board Dimensions ............................................................... 4
Installations ....................................................... 5
Installing the CPU ............................................................... 6
ATX Power Installation ...................................................... 6
Installing the Memory ......................................................... 7
Setting the Jumpers ............................................................. 8
Connectors on MI941 ........................................................ 11
BIOS Setup ....................................................... 19
Drivers Installation ...................................... 41
Intel Chipset Software Installation Utility......................... 42
Intel G41 Chipset Family Graphics Driver Installation .... 45
Realtek High Definition Audio Driver Installation ........... 48
Intel PRO LAN Network Drivers Installation ................... 50
Appendix ........................................................... 54
A. I/O Port Address Map................................................... 54
B. Interrupt Request Lines (IRQ) ...................................... 55
C. Watchdog Timer Configuration.................................... 56
MI941 User’s Manual
iii
This page is intentionally left blank.
iv
MI941 User’s Manual
INTRODUCTION
Introduction
Checklist
Your MI941 Core 2 Duo motherboard package should include the items
listed below:
• The MI941 motherboard
• This User’s manual
• 1 x I/O shield
• 1 x IDE cable
• 1 x SATA cable
• 1 CD containing the following:
• Chipset Drivers
• Flash Memory Utility
MI941 User’s Manual
1
INSTALLATIONS
Product Description
The MI941 Mini-ITX motherboard is designed for either the Intel®
Core™2 Duo or Core™2 Quad processors of up to 1333MHz FSB.
It is based on the Intel G41 Express chipset and it comes with two
dual-channel DDR3 memory slots and 4GB memory capacity for
faster system responsiveness and support of 64-bit computing.
Dual independent display comes to life with the onboard Intel®
G41 integrated graphics with CRT and DVI display interface. LAN
functionality is supported with a single Gigabit Ethernet
controllers.
MI941 is supports high-end features including high definition
audio, ten fast USB 2.0 ports, four SATAII and an eSATA port,
watchdog timer, digital I/O and four serial ports. Board
dimensions are 170mm by 170mm.
MI941 FEATURES
•
•
•
•
•
•
•
2
Supports Intel® Core™2 Quad / Core™2 Duo /
Pentium® Dual Core/ Celeron® processors
800MHz/1066MHz/1333MHz FSB
DDR3 DIMM x2, Max. 4GB
Single Gigabit LAN
Integrated G41 VGA for CRT & DVI interface
6x USB 2.0, 4x SATA II, 2x COM
HD audio, Watchdog timer, 1x PCI , 1x PCI-E x1
MI941 User’s Manual
INTRODUCTION
Specifications
Form Factor
Processor
FSB
Chipset
BIOS
Memory
Video
LAN
USB
SATA II
IDE
Audio
LPC I/O
Hardware Monitor
Edge Connectors
On Board Headers
/ Connectors
Expansion
RTC
Watchdog Timer
Digital IO
Other
Power Connector
System Voltage
RoHS Compliant
Board Size
Mini ITX
Supports Intel® Core TM 2 Quad /Core TM 2 Duo/ Celeron® processor
LGA775 socket
800/1066/1333 MHz
Intel® G41 Chipset consisting of:
Intel® 82G41 Graphic Memory Controller Hub (GMCH) (25W)
Intel® 82801GB (ICH7) I/O Controller Hub(3.3W)
Phoenix BIOS
Two 240-pin DDRIII 800/1066 DIMM sockets
Supports max. 4 GB system memory
Intel G41 integrated graphic subsystem(GMA X4500) , dual
independent display available through on-board VGA and DVI-D
1. Intel 82583V PCI Express Gigabit LAN controller x1
Intel ICH7 built-in USB 2.0 host controller, supports 6 ports:
- 4 ports in the rear I/O region, 2 ports with on-board headers
Intel ICH7 built-in SATA II controller (3.0Gb/sec) w/ 4 ports
ICH7 built-in one channel Ultra DMA 33/66/100
Intel ICH7 built-in high definition audio w/ Realtek ALC662 Codec
Winbond W83627DHG-P: COM1 (RS232), COM2
(RS232/422/485) & Hardware monitor
One fan connectors with tachometer support
CPU fan connector supports 4-wire fan with PWM control
Supports three thermal diodes (CPU die + 2 on-board)
Voltage monitoring for VCC (processor), 3.3V, 5V, and 12V
PS/2 stack connector x1 for KB/MS
DB9 connector x 1 for COM1
Stack connector x 1 for VGA+DVI-D
RJ45 + dual USB stack connector x1 for LAN1 & USB1~2
Stack dual USB connector x1 for USB 3 & 4
Triple (3x1) phone jack stack connector x1 for High-Definition Audio
Standard SATA (7-pin shrouded vertical) connector x4
2x4 pins pin-header x1 for USB 5-6
2x5 pins DF11-10 x1 for COM2 (RS232/422/485)
2x5 pins pin-header x1 for Digital I/O
2x5 pins pin-header x1 for front panel audio
40 pins box-header x1 for IDE
4 pins pin-header x1 for CPU fan & 3 pins pin-header x2 system fan
PCI +PCI-e(x1) slot x1
2x8 pins pin header x1 for adaptor card:
ƒ
ID394 (4 serial ports)
ƒ
ID395 (TPM function)
ICH7 built-in RTC with on-board lithium battery
Yes (256 segments, 0, 1, 2…255 sec/min)
4 in and 4 Out
LAN Wakeup
ATX
+5V, +3.3V, +12V, -12V & 5VSB
Yes
170 x 170mm
MI941 User’s Manual
3
INSTALLATIONS
Board Dimensions
4
MI941 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the MI941 in order to set up a workable system. The
topics covered are:
Installing the CPU ................................................................................. 6
ATX Power Installation ......................................................................... 6
Installing the Memory ........................................................................... 7
Setting the Jumpers................................................................................ 8
Connectors on MI941 .......................................................................... 11
MI941 User’s Manual
5
INSTALLATIONS
Installing the CPU
The MI941 motherboard supports an LGA 775 processor socket for
Intel® Core 2 Duo processors.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.
ATX Power Installation
The system power is provided to the motherboard with the ATX2 and
ATX1 power connectors. ATX2 is a 24-pin power connector and ATX1
is a 4-pin 12V power connector.
The 24-pin power connector can to be connected to a standard 20-pin
ATX power connector in a standard ATX power supply (Min. 400watt).
Note: The power supply 5VSB voltage must be at least 2A.
6
MI941 User’s Manual
INSTALLATIONS
Installing the Memory
The MI941 motherboard supports two DDR3 memory sockets for a
maximum total memory of 4GB. It supports DDR3 800/1066MHz.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 6.4GB/s (DDR3 1066) for two-channel
mode.
Supports 512Mb, 1Gb DDR3 technologies.
Supports only x8, x16, DDR3 devices with four banks
Supports only unbuffered DIMMs
Supports opportunistic refresh
Up to 32 simultaneously open pages (four per row, four rows
maximum)
MI941 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on the motherboard are used to select various settings
and features according to your needs and applications. Contact your
supplier if you have doubts about the best configuration for your needs.
The following lists the connectors and their respective functions.
Jumper Locations on MI941 .................................................................. 9
JP1, JP2, JP3: RS232/422/485 (COM2) Selection .............................. 10
JP6: Clear CMOS Contents ................................................................. 10
8
MI941 User’s Manual
INSTALLATIONS
Jumper Locations on MI941
JP1, JP2, JP3: RS232/422/485 (COM2) Selection .............................. 10
JP6: Clear CMOS Contents ................................................................. 10
MI941 User’s Manual
9
INSTALLATIONS
JP1, JP2, JP3: RS232/422/485 (COM2) Selection
COM2 is selectable for RS232, RS-422 and RS-485.
COM2
Function
Jumper
Setting
(pin closed)
RS-232
RS-422
RS-485
JP1:
1-2
JP1:
3-4
JP1:
5-6
JP2:
3-5 & 4-6
JP2:
1-3 & 2-4
JP2:
1-3 & 2-4
JP3:
3-5 & 4-6
JP3:
1-3 & 2-4
JP3:
1-3 & 2-4
JP6: Clear CMOS Contents
Use JP6, a 3-pin header, to clear the CMOS contents.
Note that the ATX-power connector should be disconnected from the
motherboard before clearing CMOS.
JP6
10
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
MI941 User’s Manual
INSTALLATIONS
Connectors on MI941
The connectors on MI941 allow you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The
following table lists the connectors on MI941 and their respective
functions.
ATX2: 24-pin ATX Power Connector ................................................ 13
ATX1: ATX 12V Power Connector .................................................... 13
DDRIII1: Channel A DDR3 Socket .................................................... 13
DDRIII2: Channel B DDR3 Socket .................................................... 13
CPU_FAN1: CPU Fan Power Connector ............................................ 13
SYS_FAN1: System Fan1 Power Connector ...................................... 13
SYS_FAN2: System Fan2 Power Connector ...................................... 14
CN1: Serial Ports(COM1) ................................................................... 14
CN5: Gigabit LAN (Intel 82583V) RJ-45 &USB 0/1 Connector ....... 15
CN6: DVI-D+CRT Connector ............................................................ 15
CN7: USB 2/3 Connector .................................................................... 15
CN12: PS/2 Keyboard and PS/2 Mouse Connectors ........................... 16
CN13: Audio Connector ...................................................................... 16
CN8, CN9, CN10, CN11: SATA HDD Connectors............................ 16
J1: Digital I/O Connector (4 in, 4 out)................................................. 16
J5: SPI Debug Tools Port (Factory use only) ............................................ 17
J8: Power LED .................................................................................... 17
J9: System Function Connector ........................................................... 17
J10: USB 4/5 Connector ...................................................................... 18
J11: For LPC I/F Adaptor Card ........................................................... 18
J13: Audio Front Header ..................................................................... 18
IDE1: Primary IDE Connectors ........................................................... 18
PCI1: PCI Slot (supports two masters) ................................................ 18
PCIE1: x1 PCI Express Slot ................................................................ 18
MI941 User’s Manual
11
INSTALLATIONS
Connector Locations on MI941
ATX2: 24-pin ATX Power Connector ................................................................................................... 13
ATX1: ATX 12V Power Connector ....................................................................................................... 13
DDRIII1: Channel A DDR3 Socket ....................................................................................................... 13
DDRIII2: Channel B DDR3 Socket ....................................................................................................... 13
CPU_FAN1: CPU Fan Power Connector ............................................................................................... 13
SYS_FAN1: System Fan1 Power Connector .........................................................................................13
SYS_FAN2: System Fan2 Power Connector .........................................................................................14
CN1: Serial Ports(COM1) ...................................................................................................................... 14
CN5: Gigabit LAN (Intel 82583V) RJ-45 &USB 0/1 Connector .......................................................... 15
CN6: DVI-D+CRT Connector ................................................................................................................ 15
CN7: USB 2/3 Connector ....................................................................................................................... 15
CN12: PS/2 Keyboard and PS/2 Mouse Connectors ............................................................................. 16
CN13: Audio Connector ......................................................................................................................... 16
CN8, CN9, CN10, CN11: SATA HDD Connectors ..............................................................................16
J1: Digital I/O Connector (4 in, 4 out) ................................................................................................... 16
J5: SPI Debug Tools Port (Factory use only) ......................................................................................... 17
J8: Power LED ........................................................................................................................................ 17
J9: System Function Connector .............................................................................................................. 17
J10: USB 4/5 Connector ......................................................................................................................... 18
J11: For LPC I/F Adaptor Card .............................................................................................................. 18
J13: Audio Front Header ........................................................................................................................ 18
IDE1: Primary IDE Connectors .............................................................................................................. 18
PCI1: PCI Slot (supports two masters) ................................................................................................... 18
PCIE1: x1 PCI Express Slot ................................................................................................................... 18
12
MI941 User’s Manual
INSTALLATIONS
ATX2: 24-pin ATX Power Connector
Signal Name
3.3V
-12V
Ground
PS-ON
Ground
Ground
Ground
-5V
+5V
+5V
+5V
Ground
Pin #
13
14
15
16
17
18
19
20
21
22
23
24
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
Signal Name
3.3V
3.3V
Ground
+5V
Ground
+5V
Ground
Power good
5VSB
+12V
+12V
+3.3V
ATX1: ATX 12V Power Connector
This connector supplies the CPU operating voltage.
Pin #
1
2
3
4
Signal Name
Ground
Ground
+12V
+12V
DDRIII1: Channel A DDR3 Socket
DDRIII2: Channel B DDR3 Socket
CPU_FAN1: CPU Fan Power Connector
Pin #
1
2
3
4
Signal Name
Ground
+12V
Rotation detection
Control
SYS_FAN1: System Fan1 Power Connector
Pin #
Signal Name
1
Ground
2
+12V
3
Rotation detection
MI941 User’s Manual
13
INSTALLATIONS
SYS_FAN2: System Fan2 Power Connector
Pin #
1
2
3
Signal Name
Ground
+12V
Rotation detection
CN1: Serial Ports(COM1)
CN1 (COM1) is a DB-9 connector,
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
Pin #
1
2
3
4
5
Pin #
6
7
8
9
10
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
J2: COM2 is jumper selectable for RS-232, RS-422 and RS-485.
Pin #
RS-232
1
2
3
4
5
6
7
8
9
10
14
DCD
RX
TX
DTR
Ground
DSR
RTS
CTS
RI
NC
Signal Name
R2-422
RS-485
TXTX+
RX+
RXGround
NC
NC
NC
NC
NC
MI941 User’s Manual
DATADATA+
NC
NC
Ground
NC
NC
NC
NC
NC
INSTALLATIONS
CN5: Gigabit LAN (Intel 82583V) RJ-45 &USB 0/1 Connector
CN6: DVI-D+CRT Connector
Signal Name
Red
Blue
GND
GND
VCC
N.C.
HSYNC
DDCCLK
Pin #
1
3
5
7
9
11
13
15
Pin # Signal Name
2
Green
4
N.C.
6
GND
8
GND
10
GND
12
DDCDATA
14
VSYNC
Signal Name
DATA2GND
N.C.
DDCDATA
DATA1GND
N.C.
GND
Pin #
1
3
5
7
9
11
13
15
DATA0GND
N.C.
CLK+
17
19
21
23
Pin # Signal Name
2
DATA2+
4
N.C.
6
DDCCLK
8
N.C.
10
DATA1+
12
N.C.
14
VCC
16
Hot Plug
Detect
18
DATA0+
20
N.C.
22
GND
24
CLK-
CN7: USB 2/3 Connector
MI941 User’s Manual
15
INSTALLATIONS
CN12: PS/2 Keyboard and PS/2 Mouse Connectors
Keyboard Signal
Pin #
Mouse Signal
Keyboard data
1
Mouse data
N.C.
2
N.C.
GND
3
GND
5V
4
5V
Mouse (top)
Keyboard clock
5
Mouse clock
Keyboard (bottom)
N.C.
6
N.C.
CN13: Audio Connector
CN13 is a 3-jack audio connector.
CN8, CN9, CN10, CN11: SATA HDD Connectors
Pin # Signal Name
1
Ground
2
TX+
3
TX4
Ground
5
RX6
RX+
7
Ground
J1: Digital I/O Connector (4 in, 4 out)
J1 supports TTL levels and is used to control external devices requiring
ON/OFF circuitry.
Signal Name Pin # Pin # Signal Name
Ground
1
2
+5V
Out3
3
4
Out1
Out2
5
6
Out0
IN3
7
8
IN1
IN2
9
10
IN0
16
MI941 User’s Manual
INSTALLATIONS
J5: SPI Debug Tools Port (Factory use only)
J8: Power LED
The power LED indicates the status of the main power switch.
Pin #
1
2
3
Signal Name
Power LED
No connect
Ground
J9: System Function Connector
ATX Power ON Switch: Pins 1 and 2
This 2-pin connector is an “ATX Power Supply On/Off Switch” on the
system that connects to the power switch on the case. When pressed, the
power switch will force the system to power on. When pressed again, it
will force the system to power off.
Hard Disk Drive LED Connector: Pins 3 and 4
This connector connects to the hard drive activity LED on control panel.
This LED will flash when the HDD is being accessed.
Pin #
4
3
Signal Name
HDD Active
5V
Reset Switch: Pins 5 and 6
The reset switch allows the user to reset the system without turning the
main power switch off and then on again. Orientation is not required
when making a connection to this header.
+5V and 5VSB Signals: Pins 7 and 8
Pin #
7
8
Signal Name
+5V
+5VSB
MI941 User’s Manual
17
INSTALLATIONS
J10: USB 4/5 Connector
Signal Name
Vcc
D0D0+
Ground
Pin
1
3
5
7
Pin
2
4
6
8
Signal Name
Ground
D1+
D1Vcc
J11: For LPC I/F Adaptor Card
J13: Audio Front Header
Signal Name Pin #
MIC2_L
1
MIC2_R
3
Line2_R
5
Sense
7
Line2_L
9
Pin #
2
4
6
8
10
IDE1: Primary IDE Connectors
Signal Name
Pin #
Reset IDE
1
Host data 7
3
Host data 6
5
Host data 5
7
Host data 4
9
Host data 3
11
Host data 2
13
Host data 1
15
Host data 0
17
Ground
19
DRQ0
21
Host IOW
23
Host IOR
25
IOCHRDY
27
DACK0
29
IRQ14
31
Address 1
33
IDE1
Address 0
35
Chip select 0
37
Activity
39
Signal Name
Ground
Presence#
MIC2_ID
NC
Line2_ID
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
PCI1: PCI Slot (supports two masters)
PCIE1: x1 PCI Express Slot
18
MI941 User’s Manual
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the AMI
(American Megatrends, Inc.) BIOS that comes with the board. The
topics covered in this chapter are as follows:
BIOS Introduction ............................................................................... 20
BIOS Setup .......................................................................................... 21
Main BIOS Setup ................................................................................ 22
Advanced Settings ............................................................................... 23
PCIPnP Settings................................................................................... 32
Boot Settings ....................................................................................... 34
Security Settings .................................................................................. 35
Advanced Chipset Settings .................................................................. 36
Exit Setup ............................................................................................ 39
MI941 User’s Manual
19
BIOS SETUP
BIOS Introduction
This chapter describes the different settings available in the AMI
(American Megatrends, Inc.) BIOS that comes with the board. The
topics covered in this chapter are as follows:
BIOS Introduction ............................................................................... 20
BIOS Setup .......................................................................................... 21
Main BIOS Setup ................................................................................. 22
Advanced Settings ............................................................................... 23
PCIPnP Settings ................................................................................... 32
Boot Settings ........................................................................................ 34
Security Settings .................................................................................. 35
Advanced Chipset Settings .................................................................. 36
Exit Setup............................................................................................. 39
20
MI941 User’s Manual
BIOS SETUP
BIOS Introduction
The BIOS (Basic Input/Output System) installed in your computer
system’s ROM supports Intel processors. The BIOS provides critical
low-level support for a standard device such as disk drives, serial ports
and parallel ports. It also adds virus and password protection as well as
special support for detailed fine-tuning of the chipset controlling the
entire system.
BIOS Setup
The BIOS provides a Setup utility program for specifying the system
configurations and settings. The BIOS ROM of the system stores the
Setup utility. When you turn on the computer, the BIOS is immediately
activated. Pressing the <Del> key immediately allows you to enter the
Setup utility. If you are a little bit late pressing the <Del> key, POST
(Power On Self Test) will continue with its test routines, thus preventing
you from invoking the Setup. If you still wish to enter Setup, restart the
system by pressing the ”Reset” button or simultaneously pressing the
<Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the
system Off and back On again. The following message will appear on
the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
MI941 User’s Manual
21
BIOS SETUP
Main BIOS Setup
This setup allows you to record some basic hardware configurations in
your computer system and set the system clock.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Chipset
Exit
System Overview
Processor
Intel(R) Core(TM)2 Duo CPU
Speed
: 2666MHz
Count
:1
T9400 @ 266GHz
Use[ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
Use [+] or [-] to
configure system Time.
System Memory
Size
: 3995MB
System Time
System Date
Note:
[02:29:50]
[Fri 01/02/2009]
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
If the system cannot boot after making and saving system
changes with Setup, the AMI BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both AMI and your system manufacturer
to provide the absolute maximum performance and
reliability. Changing the defaults could cause the system to
become unstable and crash in some cases.
22
MI941 User’s Manual
BIOS SETUP
Advanced Settings
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Advanced Settings
Chipset
Exit
Configure CPU.
WARNING: Setting wrong values in below sections
may cause system to malfunction.
► CPU Configurations
► IDE Configuration
► SuperIO Configuration
► Hardware Health Confguration
► ACPI Configuration
► APM Configuration
► MPS Configuration
► Smbios Configuration
► USB Configuration
The Advanced BIOS Settings
► CPU Configurations
► IDE Configuration
► SuperIO Configuration
► Hardware Health Confguration
► ACPI Configuration
► APM Configuration
► MPS Configuration
► Smbios Configuration
► USB Configuration
contains
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
the
following
sections:
The fields in each section are shown in the following pages, as seen in the
computer screen. Please note that setting the wrong values may cause the system
to malfunction. If unsure, please contact technical support of your supplier.
MI941 User’s Manual
23
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Configure advanced CPU settings
Manufacturer: Intel
Intel® Core(TM)2 Duo CPU
Frequency
: 2.66GHz
FSB Speed
: 1332MHz
Cache L1 : 128KB
Cache L2 : 6144KB
Ratio Actual Value: 8
Hardware Prefetcher
Adjacent Cache Line Prefetch
Max CPU ID Value Limit
Intel(R) Virtualization Tech
Chipset
Exit
Configure CPU.
T9400 @ 2.66GHz
[Enabled]
[Enabled]
[Disabled]
[Enabled]
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
The CPU Configuration menu shows the following CPU details:
Manufacturer: the name of the CPU manufacturer
Brand String: the brand name of the CPU being used
Frequency: the CPU processing speed
FSB Speed: the FSB speed
Cache L1: the CPU L1 cache size
Cache L2: the CPU L2 cache
Hardware Prefetcher
The hardware prefetcher operates transparently, without programmer
intervention, to fetch streams of data and instruction from memory into
the unified second-level cache. The prefetcher is capable of handling
multiple streams in either the forward or backward direction. It is
triggered when successive cache misses occur in the last-level cache and
a stride in the access pattern is detected, such as in the case of loop
iterations that access array elements. The prefetching occurs up to a page
boundary.
24
MI941 User’s Manual
BIOS SETUP
Adjacent Cache-Line Prefetch
The Adjacent Cache-Line Prefetch mechanism, like automatic hardware
prefetch, operates without programmer intervention. When enabled
through the BIOS, two 64-byte cache lines are fetched into a 128-byte
sector, regardless of whether the additional cache line has been
requested or not. In applications with relatively poor spatial locality, the
cache miss ratio is higher. A cache miss on an Intel® Pentium® 4
processor-based system (with adjacent sector prefetch enabled) brings in
128 bytes, leading to higher bus utilization (assuming that the
application didn’t need the other 64 bytes). When adjacent sector
prefetch is disabled, an Intel® P entium® 4 processor-based system only
fetches 64 bytes. The other 64 bytes of the sector in the last-level cache
are not used unless the application explicitly issues a load to that address.
Disabling adjacent sector prefetch on Intel® Pentium® 4
processor-based systems can reduce bus traffic.
MI941 User’s Manual
25
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
IDE Configuration
ATA/IDE Configuration
Legacy IDE Channels
[Compatible]
[SATA Pri, PATA Sec]
Primary IDE Master
Primary Slave Master
► Secondary IDE Master
► Secondary IDE Slave
: [Not Detected]
: [Not Detected]
: [Hitachi HDS72]
: [Not Detected]
IDE Detect Time Out (Sec)
[35]
►
►
Chipset
Exit
Options:
Disabled
Compatible
Enhanced
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
The IDE Configuration menu is used to change and/or set the
configuration of the IDE devices installed in the system.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Chipset
Exit
Configure Win627DHG Super IO Chipset
Serial Port1 Address
Serial Port2 Address
Restore on AC Power Loss
Power On Function
[3F8/IRQ4]
[2F8/IRQ3]
[Power Off]
[None]
Onboard Serial Port
The default values are:
Serial Port 1: 3F8/IRQ4
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
Serial Port 2: 2F8/IRQ3
Restore on AC Power Loss
This field sets the system power status whether on or off when power
returns to the system from a power failure situation.
Power On Function
This field is related to how the system is powered on . The options are
None, Mouse Left, Mouse Right, and Any Key.
26
MI941 User’s Manual
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Hardware Health Configuration
Chipset
Exit
Configure CPU.
System Temperature
CPU Temperature
VTIN Temperature
:35°C/95°F
:34°C/93°F
:37°C/98°F
SystemFan2 Speed
CPUFAN Speed
:0 RPM
:2280 RPM
Vcore(V)
3VCC
12V
5V
VBAT (V)
CPU smart fan
:1.160 V
:3.392 V
:12.196 V
: 5.273V
:3.21 V
[55°C]
ACPI Shutdown Temperature
[Disabled]
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
The Hardware Health Configuration menu is used to show the operating
temperature, fan speeds and system voltages.
ACPI Shutdown Temperature
The system will shut down automatically under OS with ACPI mode,
when the CPU temperature reaches the configured temperature.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
ACPI Settings
►General ACPI Configuration
MI941 User’s Manual
Chipset
Exit
General ACPI
Configuration settings
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
27
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
General ACPI Configuration
Suspend mode
Repost Video on S3 Resume
[S3 (STR)]
[No]
Suspend Mode
The options of this field are S1, S3 and Auto.
Repost Video on S3 Resume
The default setting is No.
28
MI941 User’s Manual
Chipset
Exit
General ACPI
Configuration settings
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
APM Configuration
Power Management/APM
[Enabled]
Resume On Ring
Resume On PME#
Resume On RTC Alarm
Disabled
Disabled
Disabled
Chipset
Exit
Disable/Enable
RI to generate
a wake event.
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
Resume on Ring
This option is used to enable activity on the RI (ring in) modem line to
wake up the system from a suspend or standby state. That is, the system
will be awakened by an incoming call on a modem.
Resume on PME#
This option is used enable activity on the PCI PME (power
managementevent) controller to wake up the system from a suspend or
standby state
Resume On RTC Alarm
This option is used to specify the time the system should be awakened
from a suspended state
MI941 User’s Manual
29
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
MPS Configuration
MPS Revision VT-d
Chipset
Exit
Select MPS
Revision
[1.1]
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for your operating system.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
SMBIOS Configuration
Smbios SMI Support
[Enabled]
Chipset
Exit
SMBIOS SMI Wrapper
support for PnP Func
50h-54h
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
SMBIOS SMI Support
Use the SMBIOS SMI Support to enable the system to support the
SMBIOS SMI wrapper for the PnP function 50h – 54h.
30
MI941 User’s Manual
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
USB Configuration
Exit
Enables support for
legacy USB. AUTO
option disables
legacy support if
no USB devices are
connected.
USB Devices Enabled:
None
Legacy USB Support
USB 2.0 Controller Mode
BIOS EHCI Hand-Off
Chipset
[Enabled]
[HiSpeed]
[Enabled]
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
The USB Configuration menu is used to read USB configuration
information and configure the USB settings.
Legacy USB Support
This option is used to enable the USB mouse and USB keyboard
support. This option is enabled by default.
USB 2.0 Controller Mode
This option is used to control USB device in HiSpeed (480Mbps) or
FullSpeed (12Mbps).This option is enabled by HiSpeed.
BIOS EHCI Hand-Off
This feature allows you to enable support for operating system without
EHCI hand-off feature.
MI941 User’s Manual
31
BIOS SETUP
PCIPnP Settings
This option configures the PCI/PnP settings.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Clear NVRAM
Plug & Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
Off Board PCI?ISA IDE Card
[No]
[No]
[64]
[Yes]
[Disabled]
[Enabled]
[Auto]
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
DMA Channel 0
DMA Channel 1
DMA Channel 3
DMA Channel 5
DMA Channel 6
DMA Channel 7
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Reserved Memory Size
[Disabled]
Chipset
Exit
Size of memory block
to reserve for legacy
ISA devices.
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
Clear NVRAM
This item is used for clearing NVRAM during system boot.
Plug & Play O/S
This lets BIOS configure all devices in the system or lets the OS
configure PnP devices not required for boot if your system has a Plug
and Play OS.
PCI Latency Timer
This item sets value in units of PCI clocks for PCI device latency timer
register. Options are: 32, 64, 96, 128, 160, 192, 224, 248.
32
MI941 User’s Manual
BIOS SETUP
Allocate IRQ to PCI VGA
This assigns IRQ to PCI VGA card if card requests IRQ or doesn't assign
IRQ to PCI VGA card even if card requests an IRQ.
Palette Snooping
This informs the PCI devices that an ISA graphics device is installed in
the system so the card will function correctly.
PCI IDE BusMaster
This uses PCI busmastering for BIOS reading / writing to IDE devices.
OffBoard PCI/ISA IDE Card
Some PCI IDE cards may require this to be set to the PCI slot number
that is holding the card.
IRQ#
Use the IRQ# address to specify what IRQs can be assigned to a
particular peripheral device.
MI941 User’s Manual
33
BIOS SETUP
Boot Settings
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Boot Settings Configuration
Quick Boot
Quiet Boot
AddOn ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Wait for ‘F1’ If Error
Hit ‘DEL’ Message Display
Interrupt 19 Capture
[Enabled]
[Disabled]
[Force BIOS]
[On]
[Auto]
[Enabled]
[Enabled]
[Disabled]
Chipset
Exit
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
Quick Boot
This allows BIOS to skp certain tests while booting. This will decrease
the time needed to boot the system.
Quite Boot
When disabled, this displays normal POST messages. When enabled,
this displays OEM Logo instead of POST messages.
AddOn ROM Display Mode
This allows user to force BIOS/Option ROM of add-on cards to be
displayed during quiet boot.
Bootup Num-Lock
This select the power-on state for numlock.
PS/2 Mouse Support
This select support for PS/w mouse.
Wait for ‘F1’ If Error
When set to Enabled, the system waits for the F1 key to be pressed when
error occurs. This allows option ROM to trap interrupt 19.
Hit <DEL> Message Display
This displays “Press <DEL> to run Setup” in POST.
Interrupt 19 Capture
This allows option ROM to trap interrupt 19.
34
MI941 User’s Manual
BIOS SETUP
Security Settings
This setting comes with two options set the system password. Supervisor
Password sets a password that will be used to protect the system and
Setup utility. User Password sets a password that will be used
exclusively on the system. To specify a password, highlight the type you
want and press <Enter>. The Enter Password: message prompts on the
screen. Type the password and press <Enter>. The system confirms your
password by asking you to type it again. After setting a password, the
screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Security Settings
Supervisor Password : Not Installed
User Password
: Not Installed
Change Supervisor Password
Change User Password
Boot Sector Virus Protection
[Disabled]
MI941 User’s Manual
Chipset
Exit
Install or Change the
Password.
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
35
BIOS SETUP
Advanced Chipset Settings
This setting configures the north bridge, south bridge and the ME
subsystem. WARNING! Setting the wrong values may cause the system
to malfunction. BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Advanced Chipset Settings
► South
Exit
Configure North Bridge
features.
WARNING: Setting wrong values in below sections
may cause system to malfunction.
► North
Chipset
Security
Bridge Configuration
Bridge Configuration
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
North Bridge Chipset Configuration
Memory Remap Feature
[Enabled]
PCI MMIO Allocation: 4GB To 3072MB
DRAM Frequency
[Auto]
Configure DRAM Timing by SPD [Enabled]
Memory Hole
[Disabled]
Initiate Graphics Adapter
[PEG/PCI]
IGD Graphics Mode Select
[Enabled, 32MB]
IGD GTT Graphics memory size [No VT mode, 2MB]
PAVP Mode
[Lite]
PEG Port Configuration
PEG Port
Chipset
Security
[Auto]
Exit
ENABLE: Allow
Remapping of
Overlapped PCI memory
above the total physical
memory.
DISABLE: Do not allow
remapping of memory
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
Memory Remap Feature
This feature allows remapping of overlapped PCI memory above the
total physical memory.
DRAM Frequency
This option is, by default, set to Auto.
36
MI941 User’s Manual
BIOS SETUP
Configure DRAM Timing by SPD
When this item is enabled, the DRAM timing parameters are set
according to the DRAM SPD (Serial Presence Detect). When disabled,
you can manually set the DRAM timing parameters through the DRAM
sub-items.
Memory Hole
This option is used to reserve memory space between 15MB and 16MB
for ISA expansion cards that require a specified area of memory to work
properly.
Initiate Graphic Adapter
This option, by default, is set to PEG/PCI.
IGD Graphics Mode Select
Use the feature to set the amount of system memory to be used by the
Internal. Graphics Devices. expansion cards that require a specified area
of memory to work properly.
IGD GTT Graphics memory size
This feature allows the user to select the IGD GTT Graphics Size. The
Default setting is No VT Mode, 2 MB
PAVP Mode
Use the feature to select the Protect Audio Video Path Mode.
PEG Port
This BIOS feature is a toggle that enables or disables the PCI Express
port.
MI941 User’s Manual
37
BIOS SETUP
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
South Bridge Chipset Configuration
USB Function
USB 2.0 Controller
Audio Controller
SMBUS Controller
Chipset
Security
[6 USB Ports]
[Disabled]
[Auto]
[Enabled]
Exit
Disabled
2 USB Ports
4 USB Ports
6 USB Ports
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
USB Function
This option enables the number of USB ports desired or disables the
USB function.
USB 2.0 Controller
This option is disabled by default.
Audio Controller
This option is used to enable the Southbridge high definition audio
controller.
SMBUS Controller
This option is enabled by default.
38
MI941 User’s Manual
BIOS SETUP
Exit Setup
The exit setup has the following settings which are:
BIOS SETUP UTILITY
Main
Advanced
PCIPnP
Boot
Security
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
Chipset
Exit
Exit system setup
after saving the
changes.
<-
Select Screen
↑↓
+Tab
F1
F10
ESC
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
Save Changes and Exit
This option allows you to determine whether or not to accept the
modifications and save all changes into the CMOS memory before exit.
Discard Changes and Exit
This option allows you to exit the Setup utility without saving the
changes you have made in this session.
Discard Changes
This option allows you to discard all the changes that you have made in
this session.
Load Optimal Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Load Failsafe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
MI941 User’s Manual
39
BIOS SETUP
This page is intentionally left blank.
40
MI941 User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows XP and Windows Vista. The software and
drivers are included with the motherboard. If you find the items missing,
please contact the vendor where you made the purchase. The contents of
this section include the following:
Intel Chipset Software Installation Utility ................................. 42
Intel G41 Chipset Family Graphics Driver Installation ............. 45
Realtek High Definition Audio Driver Installation.................... 48
Intel PRO LAN Network Drivers Installation ........................... 50
IMPORTANT NOTE:
After installing your Windows operating system (Windows XP/ Vista),
you must install first the Intel Chipset Software Installation Utility
before proceeding with the drivers installation.
MI941 User’s Manual
41
DRIVERS INSTALLATION
Intel Chipset Software Installation Utility
The Intel Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation under
Windows XP/Vista.
1. Insert the CD that comes with the board. Click Intel at the left side,
then Intel(R) G41 Chipset Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
42
MI941 User’s Manual
DRIVERS INSTALLATION
3. When the welcome screen to the Intel(R) Chipset Software
Installation Utility appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
MI941 User’s Manual
43
DRIVERS INSTALLATION
5. On Readme Information screen, click Next to continue the
installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
44
MI941 User’s Manual
DRIVERS INSTALLATION
Intel G41 Chipset Family Graphics Driver
Installation
To install the VGA drivers, follow the steps below to proceed with the
installation.
1. Insert the CD that comes with the board. Click Intel at the left side,
then Intel(R) G41 Chipset Drivers.
2. Click Intel G41 Chipset Family Graphics Driver.
MI941 User’s Manual
45
DRIVERS INSTALLATION
3. When the welcome screen of the Intel(R) Graphics Media Accelerator
Driver appears, click Next to continue.
4. Click Yes to to agree with the license agreement and continue the
installation.
46
MI941 User’s Manual
DRIVERS INSTALLATION
5. Click Next in the Readme File Information window.
6. Click Next in the Setup Progress window.
7. Setup is now complete. Click Finish to restart the computer and for
changes to take effect.
MI941 User’s Manual
47
DRIVERS INSTALLATION
Realtek High Definition Audio Driver
Installation
Follow the steps below to install the Realtek HD Codec Audio Drivers.
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
G41 Chipset Drivers.
2. Click Realtek High Definition Audio Driver.
48
MI941 User’s Manual
DRIVERS INSTALLATION
3.When the welcome screen to InstallShield Wizard for Realtek High
Definition Audio Driver appears, click Next to start the installation.
4.When the InstallShieldWizard has finished performing maintenance
operations on Realtek High Definition Codec Audio Audio Driver, click
Finish to restart the computer.
MI941 User’s Manual
49
DRIVERS INSTALLATION
Intel PRO LAN Network Drivers Installation
Follow the steps below to install Intel PRO LAN drivers.
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
G41 Chipset Drivers.
2. Click Intel(R) Gigabit Ethernet Drivers.
50
MI941 User’s Manual
DRIVERS INSTALLATION
3. In the Intel® Network Connections screen*, click Install Drivers and
Software.
4. In the welcome screen of the InstallShield Wizard for Intel(R)
Network Connections, click Next.
MI941 User’s Manual
51
DRIVERS INSTALLATION
5. In the License Agreement, Select I accept the terms in the license
agreement and click Next.
6. In the Setup Options, click the checkbox as shown below and click
Next.
52
MI941 User’s Manual
DRIVERS INSTALLATION
7. In the InstallShield Wizard screen, click Install to begin the
installation.
8. InstallShield Wizard is completed. Click Finish to exit the Wizard.
MI941 User’s Manual
53
APPENDIX
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses that also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278h - 27Fh
2F8h - 2FFh
2B0h - 2DFh
378h - 3FFh
360h - 36Fh
3B0h - 3BFh
3C0h - 3CFh
3D0h - 3DFh
3F0h - 3F7h
3F8h - 3FFh
54
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
MI941 User’s Manual
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
MI941 User’s Manual
55
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sorts of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user
will restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
====
#include <stdio.h>
#include <stdlib.h>
#include "W627EHF.H"
//=======================================================================
====
int main (int argc, char *argv[]);
void copyright(void);
void EnableWDT(int);
void DisableWDT(void);
//=======================================================================
====
int main (int argc, char *argv[])
{
unsigned char bBuf;
unsigned char bTime;
char **endptr;
copyright();
if (argc != 2)
{
printf(" Parameter incorrect!!\n");
return 1;
}
if (Init_W627EHF() == 0)
{
printf(" Winbond 83627HF is not detected, program abort.\n");
return 1;
}
bTime = strtol (argv[1], endptr, 10);
56
MI941 User’s Manual
APPENDIX
printf("System will reset after %d seconds\n", bTime);
EnableWDT(bTime);
return 0;
}
//=======================================================================
void copyright(void)
{
printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO DETECT)
========\n"\
"
Usage : W627E_WD reset_time\n"\
"
Ex : W627E_WD 3 => reset system after 3 second\n"\
"
W627E_WD 0 => disable watch dog timer\n");
}
//=======================================================================
void EnableWDT(int interval)
{
unsigned char bBuf;
bBuf = Get_W627EHF_Reg( 0x2D);
bBuf &= (!0x01);
Set_W627EHF_Reg( 0x2D, bBuf);
//Enable WDTO
Set_W627EHF_LD( 0x08);
Set_W627EHF_Reg( 0x30, 0x01);
//switch to logic device 8
//enable timer
bBuf = Get_W627EHF_Reg( 0xF5);
bBuf &= (!0x08);
Set_W627EHF_Reg( 0xF5, bBuf);
//count mode is second
Set_W627EHF_Reg( 0xF6, interval);
//set timer
}
//=======================================================================
void DisableWDT(void)
{
Set_W627EHF_LD(0x08);
//switch to logic device 8
Set_W627EHF_Reg(0xF6, 0x00);
//clear watchdog timer
Set_W627EHF_Reg(0x30, 0x00);
//watchdog disabled
}
//=======================================================================
MI941 User’s Manual
57
APPENDIX
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
====
#include "W627EHF.H"
#include <dos.h>
//=======================================================================
====
unsigned int W627EHF_BASE;
void Unlock_W627EHF (void);
void Lock_W627EHF (void);
//=======================================================================
unsigned int Init_W627EHF(void)
{
unsigned int result;
unsigned char ucDid;
W627EHF_BASE = 0x2E;
result = W627EHF_BASE;
ucDid = Get_W627EHF_Reg(0x20);
if (ucDid == 0x88)
{
goto Init_Finish; }
W627EHF_BASE = 0x4E;
result = W627EHF_BASE;
ucDid = Get_W627EHF_Reg(0x20);
if (ucDid == 0x88)
{
goto Init_Finish; }
W627EHF_BASE = 0x00;
result = W627EHF_BASE;
Init_Finish:
return (result);
}
//=======================================================================
void Unlock_W627EHF (void)
{
outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK);
outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK);
}
//=======================================================================
====
void Lock_W627EHF (void)
{
outportb(W627EHF_INDEX_PORT, W627EHF_LOCK);
}
//=======================================================================
void Set_W627EHF_LD( unsigned char LD)
{
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, W627EHF_REG_LD);
outportb(W627EHF_DATA_PORT, LD);
58
MI941 User’s Manual
APPENDIX
Lock_W627EHF();
}
//=======================================================================
void Set_W627EHF_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, REG);
outportb(W627EHF_DATA_PORT, DATA);
Lock_W627EHF();
}
//=======================================================================
unsigned char Get_W627EHF_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, REG);
Result = inportb(W627EHF_DATA_PORT);
Lock_W627EHF();
return Result;
}
//=======================================================================
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
#ifndef __W627EHF_H
#define __W627EHF_H
1
//=======================================================================
#define
W627EHF_INDEX_PORT
(W627EHF_BASE)
#define
W627EHF_DATA_PORT
(W627EHF_BASE+1)
//=======================================================================
#define
W627EHF_REG_LD
0x07
//=======================================================================
#define W627EHF_UNLOCK
0x87
#define
W627EHF_LOCK
0xAA
//=======================================================================
unsigned int Init_W627EHF(void);
void Set_W627EHF_LD( unsigned char);
void Set_W627EHF_Reg( unsigned char, unsigned char);
unsigned char Get_W627EHF_Reg( unsigned char);
//=======================================================================
#endif
//__W627EHF_H
MI941 User’s Manual
59
APPENDIX
File of the Main.cpp
//=====================================================================
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//=====================================================================
#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "W627HF.H"
//=====================================================================
void ClrKbBuf(void);
int main (int argc, char *argv[]);
//=====================================================================
int main (int argc, char *argv[])
{
unsigned char ucDO = 0;
//data for digital output
unsigned char ucDI;
//data for digital input
unsigned char ucBuf;
Set_W627HF_LD( 0x07);
//switch to logic device 7
Set_W627HF_Reg(0xF1, 0x00);
ucDI = Get_W627HF_Reg(0xF1) & 0x0F;
//clear
ClrKbBuf();
while(1)
{
ucDO++;
Set_W627HF_Reg(0xF1, ((ucDO & 0x0F) << 4));
ucBuf = Get_W627HF_Reg(0xF1) & 0x0F;
if (ucBuf != ucDI)
{
ucDI = ucBuf;
printf("Digital I/O Input Changed. Current Data is 0x%X\n",ucDI);
}
if (kbhit())
{
getch();
break;
}
delay(500);
}
return 0;
}
//=====================================================================
void ClrKbBuf(void)
{
while(kbhit())
{
getch();
}
}
//---------------------------------------------------------------------------
60
MI941 User’s Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising