SW-HBT-C6IRLT-8X8E
Control Your Video
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
8 x 8 HDMI HDBaseT Lite CAT5e/6/7 Matrix
with 3D Support and Bi-Directional IR
Model #: SW-HBT-C6IRLT-8X8E
© 2015 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Rev. 3.15
Product Application & Market Sectors
Corporate
House Of Worship
Military
Residential
Education
Industrial
Medical
Aviation
www.avenview.com
TABLE OF CONTENTS
1.
GETTING STARTED ........................................................................................................................3
1.1 IMPORTANT SAFEGUARDS ........................................................................................................... 3
otices SAFETY INSTRUCTIONS ................................................................................................................. 3
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ......................4
2. INTRODUCTION AND FEATURES ................................................................................................5
2.1 PACKAGE CONTENTS ...................................................................................................................6
2.2 BEFORE INSTALLATION .................................................................................................................. 7
2.3 CABLE SPECIFICATIONS ................................................................................................................. 7
2.4 APPLICATION DIAGRAM .................................................................................................................8
3. PANEL DESCRIPTION ......................................................................................................................9
3.1 FRONT PANEL (SW-HBT-C6IRLT-8X8E) ..............................................................................................9
3.2 REAR PANEL (SW-HBT-C6IRLT-8X8E) .................................................................................................10
3.3 COMPATIBLE RECEIVERS (SW-C6IRLT-R) ...........................................................................................11
3.3.1 RECEIVER FRONT AND REAR PANEL (SW-C6IRLT-R) .................................................................11
3.3.2 RECEIVER (SW-C6IRLT-R) SPECIFICATIONS .................................................................................11
4. IR REMOTE AND CABLE DEFINITION ............................................................................................12
5. INSTALLATION............................................................................................................................... 13
Protoco RS 232 PROTOCOLS ......................................................................................................................... 14
7. SPECIFICATIONS ............................................................................................................................15
www.avenview.com
Page 2
1. GETTING STARTED
SECTION 1: GETTING STARTED
ortant
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
•• Any product, on which the serial number has been defaced, modified or removed.
•• Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
•• Repair or attempted repair by anyone not authorized by us.
•• Any damage of the product due to shipment.
•• Removal or installation of the product.
•• Causes external to the product, such as electric power fluctuation or failure.
•• Use of supplies or parts not meeting our specifications.
•• Normal wear and tear.
•• Any other causes which does not relate to a product defect.
•• Removal, installation, and set-up service charges.
ctions
SW-HBT-C6IRLT-8X8E HDBaseT Matrix Switcher has been tested for conformance to safety regulations and requirements, and
has been certified for international use. However, like all electronic equipments, the SW-HBT-C6IRLT-8X8E should be used with
care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to the
unit.
! Do not dismantle the housing or modify the module.
! Dismantling the housing or modifying the module may result in electrical shock or burn.
! Refer all servicing to qualified service personnel.
! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards.
! Keep the module away from liquids.
! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
! Have the module checked by a qualified service engineer before using it again.
! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
www.avenview.com
Page
3
ator
This equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE Of
THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON
A SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.
www.avenview.com
Page
2
2. ction
The SW-HBT-C6IRLT-8X8E HDBaseT™ Lite HDMI Matrix is designed to accept Full HD 1080p and WUXGA 1920X1200
@60 Hz(RB) signal from 8 DVI/HDMI sources to any of the connected 8 displays over CAT5/6 cable upto 60m (196 feet).
This matrix model has been tesetd and proven to be cost effective and reliable within the market sector because of its
HDBaseT chipset technology inside.
The unit supports not only transmission of video but multi-channel digital audio and bi directional control via IR to eight
displays for true digital experience over a single CAT5e/6/7 cable (up to 60m). Please note this matrix supports high resolution
digital audio formats such as LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio as well as 3D
content that can be displayed when connecting a 3D TV and 3D source.
Bonus feature with all our matrix series family it allow users to control the seamless matrix switching functionality via WEB
GUI over LAN with any device that supports web browser application. Example iPad, Android device or Windows 8 touch
device.
FEATURESS
• HDMI, HDCP1.1 and DVI compliant
• Supports HDMI 3D features
• Supports resolutions VGA~WUXGA and 480i~1080p dependent upon the output display’s EDID settings
• Supports distances up to 60 meters through CAT5e/6/7 cables
• Supports 3D signal display dependent upon the output display EDID settings
• Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters at 12-bit resolution
• Supports bi-directional IR from input and output locations
• Supports RS-232, IR remote control, front-panel button control and IP Control (Telnet & Web GUI)
• 2U size design
• Supports external and internal EDID settings
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio transmission
NOTE: Receivers (Rx) from different manufactures and non HDBaseT would not be compatible.
Displaying Full HD 1080p resolution would require the standard HDMI cable and display for accurate results.
Do not connect CAT inputs/outputs of this device to a POE network switch.
Doing so may damage the unit.
Only connect LAN port to a network.
www.avenview.com
Page
3
2.1
1
2
3
4
5
PACKAGE CONTENTS
board
X1
IR Extender Cable
X2
IR Blaster Cable
X2
ord
X1
Right and Left Ear Rack Sets
X1
IR Remote Control
X1
SW-C6IRLT-R Receiver (included)
IR Receiver & IR Blaster
X8
Universal Power Adapter 5v-2.6A
X1
USER ’S MANUAL
X1
www.avenview.com
Page
4
2.2 BEFORE INSTALLATION




Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or
high humidity.
Use the DC power adapter with correct specifications and supplied with the unit. If improper
power supply is used the unit may malfunction and cause a fire.
Do not twist or pull by force ends of the UTP cable. It can cause malfunction.
2.3 CABLE SPECIFICATIONS
To achieve best results with our SW-HBT-C6IRLT-4X4E we highly recommend a premium quality 26 or 24
AWG HDMI cable with the below specifications to maintain signal integrity and distances.
FEATURES:











Length: 5m (16ft) to 15m (50ft)
Bandwidth: 10.2 Gbps data transfer rate
Supports Resolution: Up to 3840x2160 @ 24Hz and 4096x2160 @ 24Hz, 1080p @ 24Hz / 50/60Hz/3D
Conductor gauge: 26 / 24 AWG
Deep Color
3D Capable
CEC
Ethernet Channel
Audio Return Channel
Connector 1: HDMI (Type A) Male
Connector 2: HDMI (Type A) Male
www.avenview.com
Page|5
2.4 APPLICATION DIAGRAM
www.avenview.com
Page
6
3.
PANEL DESCRIPTION
3.1 FRONT PANEL ( SW-HBT-C6IRLT-8X8E)
1
2
3
4
5
6
1. LCM: Displays the device settings information of each input and output and other information.
2. POWER: Power device On/Off. The LED illuminates Green - Power is on, Red - 'Standby' mode.
3. LOCK: Locks all buttons on the panel; 1st Press Lock, 2nd Press unlock. The LED will illuminate when locked.
4. IR: IR Receiver window (accepts the IR signal from this device IR Remote only).
5. MENU: Access the LCM menu system, EDID settings and IP settings can be displayed.
IN/OUT and 1~8/A~H: Matrix Function
Step 1:Press the OUT button and then select A-H buttons to select the Output ,
6. Step 2: Press IN button and then select one of 1-8 button to select Input,
Step 3: Press the MENU button to confirm the selection via LCM
For example, if outputs A~D need to be set to input 1
Press: OUT >A B C D > IN >1> MENU;
If E~H need to be set to input 2,
Press: OUT >E F G H >IN >2 > MENU;
Note: If the MENU button is not pressed the selection will not be changed.
www.avenview.com
Page
7
3.2 REAR PANEL (SW-HBT-C6IRLT-8X8E)
3
1
2
7
4 5 6 8
10
9
1. CONTROL: Telnet or Web GUI link controls, connect to a LAN with Ethernet cable (for further details, please refer
to section 6.8 & 6.9). Warning: Please do not connect this port directly to the PC/Laptop as theTelnet function will not work.
2. RS-232: Connect to a PC or control system with D-Sub 9-pin cable for RS-232 control.
3. ALL IR OUT: Connect IR blaster to send IR signals to source. Place the IR blaster on the device IR window to be
controlled. It will transmit all signals received from the IR IN.
4. ALL IR IN: Connect IR extender to receive IR signal. Ensure that the remote being used is within the direct lineof-sight of the IR extender. It will send the signal to the receiver's IR OUT.
5. SERVICE: Local use for firmware updates only.
6. IR IN 1~8: Connect to IR extenders to receive IR signal reception. Ensure that the remote being used is within the
direct line-of-sight of the IR extender. It will send the IR signal to the corresponding IR OUT.
7. IR OUT A~H: Connect to IR blasters to send IR signal. Place the IR blaster in direct line-of-sight of the equipment
to be controlled. It will transmit the IR signal received from the corresponding IR input selected in the settings menu.
8. CAT5e/6/7 OUT A~H: Connect CAT outputs to CAT input port of the receiver units with a single CAT5e/6/7
cable for HDMI Audio/Video and IR/RS-232 control signal transmission. Warning: Please do not connect the CAT5e/6/7 output into the
receiver's LAN port.
9. HDMI IN 1~8: Connect HDMI input sources such as a Blu-ray player or a Set-top Box with HDMI cables or
DVI to HDMI cables.
10. DC 24V: Connect the 24 V DC power supply to the unit and plug the adaptor into an AC outlet.
www.avenview.com
Page
8
3.3 COMPATIBLE RECEIVERS (SW-C6IRLT-R)
3.3.1 RECEIVER FRONT AND REAR PANEL (SW-C6IRLT-R)
1
2
4
3
5
1. IR-1 IN: Connect IR receiver to receive and
transmit signal to IR-1 Out at the transmitter unit
2. HDMI OUT: Connect to HDMI input (TV or
Monitor) to view the HDMI input signal.
3. IR-2 OUT: Connect to IR Blaster to send signal
to the display (TV or Monitor).
4. DC-5V: Connect the 5V DC power supply to the unit
and plug the adaptor into an AC outlet.
5.CAT5e/6 IN: Connect to sender unit with a single CAT5e/6/7 cable for transmission of data signals. Yellow
LED will illuminate when both transmitter and receiver are powered and connected together.
3.3.2 RECEIVER (SW-C6IRLT-R) SPECIFICATIONS
Item
UNITS
UNIT DESCRIPTION
Description
SW-C6IRLT-R
HDBaseTTM Lite HDMI over Single CAT5e/6/7 Extender
Video Bandwidth
300 MHz/10.2 Gbps
HDCP and DVI
Compliant
DATA RATE
5.3 Gbps
HDMI SUPPORTED RESOLUTIONS
INPUT
OUTPUT
HDMI CABLE
AUDIO SUPPORT
DIMENSIONS (L X W X H)
480i @ 60Hz, 480p @ 60Hz, 576i @ 50Hz, 576p @ 50Hz, 720p
@ 50/60Hz/3D, 1080i @ 50/60Hz,1080p @ 24Hz / 50/60Hz/3D,
ulTRA HD (3840x2160)@24Hz 4k × 2k @ 24Hz
Sender
1×HDMI, 1×IR Extender
1×CAT5e/6/7, 1×IR Blaster
1×HDMI, 1×IR Blaster
4k2k: ([email protected]) ~ 35meter (115 feet)
full HD: (1080p) ~
60meter (197 feet)
lpCM 7.1CH , Dolby TrueHD, Dolby Digital plus and DTS-HD Master
Audio
2.2” x 3.2” x 0.88” (Sender and Receiver)
WEIGHT
POWER SUPPLY
Receiver
1×CAT5e/6/7, 1×IR Extender
0.12 lb (Sender) / 0.14 (Receiver)
5 V/2.6 A DC (US/EU standards, CE/FCC/UL certified)
POWER CONSUMPTION
3 W/TX, 5.5 W/RX
Environmental
OPERATING TEMPERATURE
STORAGE TEMPERATURE
RELATIv E HUMIDITY
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (non-condensing)
www.avenview.com
Page 9
4. IR REMOTE AND CABLE DEFINITION
REMOTE CONTROL
1 POWER: Press this button to
power on the device or set it
to standby mode.
1
22 IN: Input ports selection 1~8.
33 OUT: Output ports selection A~H.
3
2
IR Blaster
1 Power 5 V
2 IR Blaster Signal
3 NC
IR Extender Receiver
1 IR Signal
2 Power 5 V
3 Grounding
IR Sockets
IR BLASTER: plug in the IR blaster to the SW-HBT-C6IRLT-8X8E IR-OUT to emit all IR command signals received from
the IR input to control the devices corresponding to the IR signals. Example: Set Top Box or DVD player (The Source).
IR EXTENDER: plug in the IR Extender into the IR-IN of the SW-HBT-C6IRLT-8X8E to receive all IR command signals
from the IR remote controls of the corresponding source. Example: Set Top Box or DVD player (IR Remote Control).
www.avenview.com
Page|10
NOTE: Incorrect placement of IR Blaster and IR Receiver into the extender may result in the
failure of the IR extenders.
Please check carefully before plugging in the IR extender to the respective IR sockets. It
is clearly marked and IR 1: IR RECEIVER/EXTENDER / IR 2: IR BLASTER
WARRANTY WILL NOT COVER THE DAMAGE
NOTE
The QUALITY and TRANSMISSION of the video signals depends on the
characteristics and quality of the UTP cables. Higher resolutions and longer
transmission distances require low skew cables (<25ns/upto 300m) for best
performance.
Unshielded CAT6 with metal RJ-45 connectors is recommended.
5. INSTALLATION (SW-HBT-C6IRLT-8X8E )
To setup Avenview SW-HBT-C6IRLT-8X8E please follow these steps for connecting to a device:
1.
2.
3.
Turn off all devices including monitors / TV
Connect to a HDMI source 1080p (such as a Blu-Ray Disc player) to the matrix unit.
Connect a SW-C6IRLT-R receiver with CAT5/6/7 cable and HDMI out to monitor.
4. Plug the supplied power supply 5V/2.6A to the Receiver unit
5. Plug in the IR BLASTER: into IR out and the blinker on the IR eye (Source)
6. Plug in the IR Receiver to IR IN to receive IR Signals from Remote (Monitor end)
7. Power on the HDMI display
8. Power on HDMI Sources
www.avenview.com
Page|11
Protoco
SW-HBT-C6IRLT-8x8E
Third Party RS-232 Controller
PIN
Definition
PIN
Definition
1
NC
1
NC
2
TxD
2
TxD
3
RxD
3
RxD
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 19200bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1
Flow Control: None
www.avenview.com
Page 12
SECTION 7: SPECIFICATIONS
ITEM
UNITS
UNIT DESCRIPTION
HDCP
VIDEO BANDWIDTH
SUPPORTED
RESOLUTIONS
AUDIO SUPPORT
HDMI IN CABLE M/M
ESD PROTECTION
INPUT
OUTPUT
DESCRIPTION
SW-HBT-C6IRLT-8X8E
HDMI HDBaseT Lite CAT5e/6/7 Matrix
YES
225 MHz/6.75 Gbps
[email protected]/60 (1920x1080), [email protected],
WUXGA (1920X1200), 3D
LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
15m/[email protected] or 6m/[email protected]
Human body model — ±8kV (air-gap discharge) & ±4kV (contact discharge)
8×HDMI/DVI, 9×IR Extender, 1×RS-232, 1×RJ-45
, 1×Mini USB Type B (For firmware updates only)
8×CAT5e/6/7, 9×IR Blaster
HDMI CABLE I/O DISTANCE
15m/8-bits, 10m/12-bits
HDMI CONNECTOR
Type A (19 pin female)
IR FREQUENCY
DIMENSIONS (L X W X H)
NET WEIGHT
POWER SUPPLY
POWER CONSUMPTION
30~50kHz
17.2' (W) x 10' (D) x 3.7' (H)
9.9 lbs
24 V/6.25 A DC (US/EU standards, CE/FCC/UL certified)
60 W
ENVIRONMENTAL
OPERATING
TEMPERATURE
STORAGE TEMPERATURE
RELATIVE HUMIDITY
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (non-condensing)
www.avenview.com
Page|13
NOTICE
1. All HDMI over UTP transmission distances are measured using Belden CAT6A (625MHz), 4-Pair, U/
UTP-Unshielded, Riser-CMR, Premise Horizontal Cable, 23 AWG Solid Bare Copper Conductors,
Polyolefin Insulation, Patented Double-H spline, Ripcord, PVC Jacket using Quantum 980 signal
HDMI Video Generator Module Video Pattern Testing.
2. The transmission length is largely affected by the type of category cables, also the type of HDMI
sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in the
form of 300m or 1000ft bulk cable) can transmit a lot longer signals than stranded UTP cables
(usually in the form of patch cords). Shielded STP connectors are better suit than unshielded UTP
connectors. A solid UTP CAT5e cable shows longer transmission length than stranded STP CAT6
cable. For long extension users, solid cables are your only choice.
3. EIA/TIA-568-B termination (T568B) for category cables is recommended for better performance.
4. To reduce the interference among the unshielded twisted pairs of wires in category cable, you can
use shielded STP cables with shielded connector to improve EMI problems, which occurs in long
transmission.
5. Because the quality of the category cables has the major effects in how long transmission distance
will be made and how good is the received display, the actual transmission length is subject to your
category cables. For resolution greater than 1080i or 1280x1024, a solid CAT6 cable is the only
viable choice.
PERFORMANCE GUIDE FOR HDMI OVER CATEGORY CABLE TRANSMISSION
PERFORMANCE RATING
SHIELDING
WIRING
UNSHIELDED (UTP)
SOLID
SHIELDED (STP)
STRANDED
UNSHIELDED (UTP)
SHIELDED (STP)
TERMINATION
TYPE OF CATEGORY CABLE
CAT5e
CAT6
CAT6A/7












PLEASE USE EIA/TIA-568-B TERMINATION (T568B) AT ANY TIME
www.avenview.com
Page|14
Notes
www.avenview.com
Page
15
Avenview Warranty Certificate
AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [email protected]
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
[email protected]
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
275 Woodward Avenue, Kenmore, NY 14217
1.866.508.0269
www.avenview.com
AV Connectivity, Distribution And Beyond...
TECHNICAL SUPPORT
USA Head Office
Office Avenview
Corp. 275 Woodward Avenue
Kenmore, Ny 14217
Phone: +1.716.218.4100 ext223
Fax: +1.866.387-8764
Email: [email protected]
Canada Sales Office
Avenview
151 Esna Park Drive, Unit 11 & 12
Markham, Ontario, L3R 3B1
Phone: 1.905.907.0525
Fax: 1.866.387.8764
Email: [email protected]
Avenview Europe
Avenview Europe
Demkaweg 11
3555 HW Utrecht
Netherlands
phone: +31 (0)85 2100- 613
Email: [email protected]
Avenview Hong kong
Unit 8, 6/f., Kwai Cheong Centre,
50 Kwai Cheong Road,
Kwai Chung, N.T.
Hong Kong
Phone: 852-3575 9585
Email: [email protected]
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement