Ediseja 21 | CMU 200 | User manual | Ediseja 21 CMU 200 User manual

Ediseja 21 CMU 200 User manual
CMU 100
RS232 to 7x, 6x, 5x, 4x
Multimode Fiber Optic
Star Coupler
User Manual
CMU 100 / 2.1.6.6.6.6.6.6.6
CMU 100 / 2.1.6.6.6.6.6.6
CMU 100 / 2.1.6.6.6.6.6
CMU 100 / 2.1.6.6.6.6
CMU 100 / 8.1.6.6.6.6.6.6.6
CMU 100 / 8.1.6.6.6.6.6.6
CMU 100 / 8.1.6.6.6.6.6
CMU 100 / 8.1.6.6.6.6
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
-
12
12
12
12
12
12
12
12
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
Content
1
PREFACE.......................................................................................................3
2
CMU 100 SYSTEM.........................................................................................6
2.1 DESCRIPTION..................................................................................................................... 6
2.1.1 SOFTWARE...................................................................................................................... 6
2.1.2 HARDWARE...................................................................................................................... 6
3
RS232 TO 7x MULTIMODE FIBER OPTIC STAR COUPLER......................8
3.1 DESCRIPTION..................................................................................................................... 8
3.2 TYPICAL APPLICATIONS.................................................................................................... 8
3.3 APPEARANCE................................................................................................................... 10
3.4 HARDWARE DESCRIPTION..............................................................................................10
3.4.1 MAIN BOARD.................................................................................................................. 10
3.4.2 RS232 INTERFACE BOARD........................................................................................... 11
3.4.3 MULTIMODE FIBER OPTIC INTERFACE BOARD..........................................................12
4
SCHEMATIC.................................................................................................13
5
INSTALLATION............................................................................................14
5.1 INSTALLATION.................................................................................................................. 14
6
COMMISSIONING & MAINTENACE..........................................................16
6.1 COMMISSIONING.............................................................................................................. 16
6.2 MAINTENANCE................................................................................................................. 16
7
TECHNICAL DATA.......................................................................................17
8
DIMENSIONS...............................................................................................19
9
ORDERING...................................................................................................20
Page:
Company:
Device:
Document:
Code:
2
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
PREFACE
1
PREFACE
Liability statement
We have checked the contents of this manual to ensure that the descriptions of both hardware
and software are as accurate as possible. However, deviations may occur so that no liability can
be accepted for any errors or omissions contained in the information given.
The contents of this manual will be checked in periodical intervals, corrections will be made in
the following editions.
We reserve the right to make technical improvements without notice.
Contact
If you have any questions or comments related to this product please contact us on:
Ediseja 21 d.o.o.
Drenov Gric 175
1360 Vrhnika
Slovenia – EU
Tel: ++386 (1) 75 05 275
Email: grega.flander@ediseja21.com
www.ediseja21.com
Copyright
Copyright © Ediseja 21, 2013. All rights reserved.
Explanation of the symbols
Read the instructions!
Device was tested with 2,5 kV AC voltage to check the device insulation.
Device ground terminal.
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC; the affixed
product label indicates that you must not discard this electrical/electronic product in
domestic household waste.
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
3
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
Warnings
In this paper the following terms are used:
Danger
indicates that death, severe personal injury or substantial property damage will result if proper
precautions are not taken.
Warning
indicates that death, severe personal injury or substantial property damage can result if proper
precautions are not taken.
Caution
indicates that minor personal injury or property damage can result if proper precautions are not
taken. This particularly applies to damage on or in the device itself.
General information
These paper contain the information that is necessary for the proper and safe operation of the
described devices. This paper is intended for technically qualified personnel.
Warning!
Hazardous voltage is present inside the device during operation. Disregarding of safety rules can
result in severe personal injury or property damage.
Only qualified personnel may work with described devices after being familiar with warnings and
safety notices in this paper and other safety regulations.
Warning!
Device must operate completely assembled! Device must be used as described. No modifications
of the device should be made.
Warning!
Do not open device while it is energized! Hazardous voltage is present inside the device.
Disconnect all connectors before opening!
Page:
Company:
Device:
Document:
Code:
4
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
PREFACE
Warning!
If device is damaged disconnect it from power supply! Send it to the manufacturer for inspection.
Warning!
Connect to earth before attaching power supply!
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
5
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
2
CMU 100 SYSTEM
2.1
DESCRIPTION
Communication unit (CMU 100) is modular system of communication devices that can be used
for various of tasks such as:






communication converter (for example RS232 to RS485)
star coupler (for example 1 fiber optic to 7 fiber optics)
repeater (for example RS485/485)
communication isolator (for example for preventing ground loops)
communication listener - debugger
PC serial com port extender (for example USB to 4 serial com)
CMU 100 device is a couple of software and hardware. For different purposes, different software
versions and different hardware configuration have been developed.
2.1.1
SOFTWARE
Software is application dependent and allows different hardware configurations. Software's task
is switching between communication ports and allows almost any combination between them.
2.1.2
HARDWARE
Hardware is based on main board with power supply and port switching logic. On that board,
interface boards are attached. CMU 100 can handle up to 8 different interface boards. Currently
available interface boards:





RS232
isolated RS485
Multimode Fiber Optic ST and SMA connectors
USB
ethernet (with one virtual com port)
Housing is aluminium and intended for mount on standard DIN 35 rail (acc. to DIN EN 50022). 3
different housings have been made. Depends on how many interfaces device has, appropriate
housing is used.
Page:
Company:
Device:
Document:
Code:
6
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
DESCRIPTION
Hardware settings
All settings on the device can be made from outside by a DIL switch. It is not necessary to open
the housing.
Picture 1: CMU 100 system general diagram
Due to similarity among stated types, only type with 7 optic port will be described.
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
7
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
3
RS232 TO 7x MULTIMODE FIBER OPTIC STAR
COUPLER
3.1
DESCRIPTION
Star coupler is communication device that transfer data from one (master) to more than one
(slave) port. Example is when we need access to one device with several PCs. It can also be
used when communication from PC to multiple devices is needed.
This device contains one ful duplex RS232 interface (master) and seven 820 nm wave lenght
multimode fiber optic (slaves). Data is send from master port to all slave ports. On the other
hand, data from either slave port is send to master port only.
Wide power supply voltage allows connection to all common station batteries. Additionaly it can
be also connected to standard AC voltages.
This device is intended for use in cubicles and cabinets in all kinds of power production,
transmission and distribution stations. It requires no maintenace. All normaly used connectors,
switches and light indicators are accessed at the front side of the device. One light indicator
indicates power supply voltage, others indicate communication transfer.
Fiber optic communication allows longer distances between devices without electromagnetic
disturbances. Fiber optic logic can be set to positive or negative logic for transmitter and receiver
separatedly. They can be set by DIP switch at the front side of the communication interface.
3.2
TYPICAL APPLICATIONS
Typical application is communication with PC with SCADA application, in control room and
protection relays, power meters, etc with RS232 interfaces, in switchgear, without
electromagnetic disturbances.
Page:
Company:
Device:
Document:
Code:
8
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
TYPICAL APPLICATIONS
Picture 2: Star coupler typical application
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
9
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
3.3
APPEARANCE
Picture 3: Front view (left) & bottom view (right)
3.4
HARDWARE DESCRIPTION
This configuration of device is made from main board (power supply, LEDs, switches and logic
switch), one RS232 interface board and seven multimode fiber optic boards.
3.4.1
MAIN BOARD
Power LED indicates that device is turned on. The right LEDs of one port shows activity on
receive (Rx) line and the left one shows activity on transmit (Tx) line.
On the bottom side of device are switches and JTAG connector which is intended for
downloading necessary software. Do not connect anything to that connector.
Additional switches allows echo on each port. Echo can be set on or off for each port.
Switches
Switch
1
2
3
4
Description
Echo port 1
Echo port 2
Echo port 3
Echo port 4
Position OFF
Echo off
Echo off
Echo off
Echo off
Position ON
Echo on
Echo on
Echo on
Echo on
Default position
OFF
OFF
OFF
OFF
Code:
Version:
Date:
V3
05.11.2014
Page:
Company:
Device:
Document:
10
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
HARDWARE DESCRIPTION
Switch
5
6
7
8
Description
Echo port 5
Echo port 6
Echo port 7
Echo port 8
Position OFF
Echo off
Echo off
Echo off
Echo off
Position ON
Echo on
Echo on
Echo on
Echo on
Default position
OFF
OFF
OFF
OFF
Configuration of ports
3.4.2
Port
1
2
3
4
5
6
7
8
Interface
RS232
FO MM
FO MM
FO MM
FO MM
FO MM
FO MM
FO MM
RS232 INTERFACE BOARD
Description
Single, nonisolated, full duplex, RS232 port with DB9 female connector. Supported Rx, Tx and
GND pins.
Connector pin table
DB9 F
2
3
5
Description
RX
TX
GND
Direction
IN
OUT
-
Picture 4: DB9 Female connector
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
11
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
3.4.3
MULTIMODE FIBER OPTIC INTERFACE BOARD
Description
Single, full duplex, multimode, fiber optic port with ST connectors with positive or negative logic.
Hardware settings
For proper functioning of that board, optic logic must be set:
Fiber optic logic settings
Switch SW1
Light in idle state
1
2
3
4
Positive logic
OFF
OFF ON OFF ON
Negative logic
ON
ON OFF ON OFF
Picture 5: Multimode fiber optic interface board appearance
It is recommended that positive logic on fiber optic interfaces is used (light OFF in idle state). In
other case, if optic loop on one port is broken, communication with other slave ports, also will not
work.
Page:
Company:
Device:
Document:
Code:
12
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
SCHEMATIC
4
SCHEMATIC
Picture 6: CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 (left) and CMU 100 / 2.1.6.6.6.6 - 12 (right) general diagram
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
13
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
5
INSTALLATION
5.1
INSTALLATION
Warning!
Hazardous voltage is present inside the device during operation. Disregarding of safety rules can
result in severe personal injury or property damage.
Only qualified personnel may work with described devices after being familiar with warnings and
safety notices in this paper and other safety regulations.
Following instruction must be taken into consideration:











The device must be accessible to qualified personnel only.
The device is permitted to operate in enclosed housing or cabinet only.
The device location must be vibration-free.
The admisible operating temperature must be observed.
Check the device for damage at unpacking. If device is damaged it must not be installed
but it should be send to the manufacturer for repair.
The device should not be opened.
The device should be mounted on a 35 mm rail (acc to EN 50022).
Attach ground wire before attaching power supply. Device must be grounded during
operation!
Single core or stranded wire 0,5 – 2,5 mm 2 must be used for power supply connection. If
stranded wire is used, ferrules must be used to prevent fraying. Recommended stripping
lenght is 5 mm.
Protective earthing wire must be terminated with tinned copper ear terminal.
The prescribed bending radius of the optical fibre cables must be observed.
Page:
Company:
Device:
Document:
Code:
14
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
INSTALLATION
Picture 7: left. installation, right: deinstallation
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
15
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
6
COMMISSIONING & MAINTENACE
6.1
COMMISSIONING
Warning!
Hazardous voltage is present inside the device during operation. Disregarding of safety rules can
result in severe personal injury or property damage.
Only qualified personnel may work with described device after being familiar with warnings and
safety notices in this paper and other safety regulations.
Following instruction must be taken into consideration:





6.2
Device must operate completely assembled! Device must be used as described. No
modifications of the device should be made.
Attach ground wire before attaching power supply. Device must be grounded during
operation!
Check if the power supply voltage complies with device operation voltage.
Do not open device while it is energized! Hazardous voltage is present inside the device.
If single mode fiber optic interface is used, do not look into the laser beam.
MAINTENANCE
The device is maintenance-free. Disconnect power supply before cleaning it. Use moist cloth.
Do not use liquids.
Page:
Company:
Device:
Document:
Code:
16
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
TECHNICAL DATA
7
TECHNICAL DATA
Power supply
Rated voltage
Permissible voltage range
Input current
Type 1
Type 7
DC
110 - 250 V
48 - 60 V
AC
230 V
48 V
DC
88 - 300 V
38 - 72 V
AC
70 - 264 V
30 - 50 V
DC
80 - 40 mA
160 - 140 mA
AC
55 mA
340 mA
Fuse (internal)
2AT
Power supply indicator
green LED marked PWR
Voltage dips
20 ms
Connector type
screw type „MSTB“ Phoenix 2pin
Wire crossection
0,5 – 2,5 mm2
Communication port RS232 (interface type 1)
Type
RS232
Direction
full duplex
Speed
up to 230 k BAUD
Number of ports
1
Distance
up to 15 m
Isolation
none; (GND earthed)
Connector type
DB9 female
Lines in
1 (RX)
Lines out
1 (TX)
Communication port Multimode Fiber Optic (interface type 6)
Company:
Type
multimode fiber optic
Wave lenght
820 nm
Fiber size
50/125 μm, 62,5/125 μm, 100/140 μm, 200 μm
Optical output power
-18 dB
Reciver sensitivity
-24 dB
Laser class
I (IEC 60825-1)
Direction
full duplex
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
17
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
Communication port Multimode Fiber Optic (interface type 6)
Speed
up to 230 k BAUD
Input
1 receiver (grey connector)
Output
1 transmitter (white connector)
Logic
light ON or OFF in idle state set by switch
(see table)
Number of ports
1
Distance
up to 500 m
Connector type
ST
* slowest interface defines device's maximum speed
Device
0,55 kg
Weight
Dimensions
(see picture)
(H)
(D)
(W)
105 mm
111 mm + connectors
85 mm
Temperature range
0 °C to +55 °C
Humidity operating
up to 95 % (noncondensing)
Enclosure
Mount type
Material
Al
IP
20
standard DIN 35 rail (acc. to DIN EN 50022)
Class
I
Overvoltage category
II
Communication indicator
Device:
Receiveing
yellow LED marked Rx
Tranmitting
green LED marked Tx
Page:
Company:
Document:
Code:
18
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
DIMENSIONS
8
DIMENSIONS
Picture 8: CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 dimensions
Picture 9: CMU 100 / 2.1.6.6.6.6-12 dimensions
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
19
CMU 100 - RS232 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star
9
ORDERING
ORDERING NUMBER:
CMU 100 / c . c . c . c . c . c . c . c . c - c . c
Mother Board + Enclosure + :
Power supply: 88 - 350 V DC or 70 - 264 V AC
2 ports converters (no echo possible, mark Function as 0) ............................................... 1
2 to 8 ports converters, star couplers, ... (echo possible) ................................................... 2
Power supply: 38 - 72 V DC or 30 - 50 V AC
2 ports converters (no echo possible, mark Function as 0) ................................................ 7
2 to 8 ports converters, star couplers, ... (echo possible) ................................................... 8
(Device width: 2 ports - 40 mm, 3 & 4 ports - 55 mm, 5 & 8 ports - 85 mm)
Interfaces:
None ................................................................................................................ leave empty or 0
RS232 nonisolated, Rx & Tx support ...................................................................................... 1
RS232 nonisolated, Rx & Tx support (custom made: LDU version with rectifiers) …............. C
RS485 isolated, half duplex (19200 - 115200 baud) ............................................................... 5
RS485 isolated, half duplex (38400 - 4800 baud) ................................................................... M
RS485 isolated, half duplex (300 - 2400 baud) ....................................................................... L
Multimode (820 nm) fiber optic with STconnector ................................................................... 6
Multimode (820 nm) fiber optic with SMA connector ............................................................... 7
USB (one virtual com port) ...................................................................................................... 8
Ethernet (one virtual com port) ................................................................................................ 9
Function:
Converter (when Mother Board marked as 1, 5 or 7 is used) …................................................... 0
3 port star coupler / communication node with echo's possible ................................................... 2
4 x 2 port converter (4 independent channels (converters)) ......................................................... 7
8 port node .................................................................................................................................... 8
8 port star coupler (1 master, 4 to 7 slaves) ................................................................................ 12
8 port star coupler (1 master, 4 to 6 slaves, 1 listener) ................................................................ 14
Software Version:
Software version ................................................................................................................. leave empty
Examples:
CMU 100 / 2.1.5.6.7 - 2 or CMU 100 / 2.1.5.6.7.0.0.0.0 - 2 is
star coupler / communication node with
- high voltage power supply and
- 4 interfaces
1. interface is RS232 master port,
2. interface is RS485 slave port,
3. interface is fiber optic with ST connectors slave port and
4. interface is fiber optic with SMA connectors slave port.
Page:
Company:
Device:
Document:
Code:
20
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216
Version:
Date:
V3
05.11.2014
ORDERING
Most common devices:
CMU 100 / 1.6.1 - 0 - 1 ch converter multimode fiber optic to RS232, high voltage power supply
CMU 100 / 1.5.1 - 0 - 1 ch converter RS485 to RS232, 19k2-115k BAUD, high voltage power supply
CMU 100 / 1.5.6 - 0 - 1 ch converter RS485 to multimode fiber optic, high voltage power supply
CMU 100 / 2.1.1.1 - 2 - 3 channel star coupler RS232 to 2 x RS232, high voltage power supply
CMU 100 / 2.1.6.6 - 2 - 3 channel star coupler RS232 to 2 x multimode fiber optic, high voltage power
supply
CMU 100 / 2.6.6.6.6.1.1.1.1 - 7 - 4 channel converter multimode fiber optic to RS232, high voltage power
supply
CMU 100 / 2.5.5.5.5.6.6.6.6 - 7 - 4 channel converter RS485 to multimode fiber optic, high voltage power
supply
CMU 100 / 2.5.6.6.6.6.6.6.6 - 12 - 8 port star coupler RS485 to 7 x multimode fiber optic, high voltage
power supply.
CMU 100 / 2.6.6.6.6.6.6.6.6 - 12 - 8 port star coupler multimode fiber optic to 7 x multimode fiber optic,
high voltage power supply
Additional accessories (order if needed):
- power supply cable with „schuko“ plug, 2 m
- RS232 cable to PC (state the lenght up to 15 m)
- fiber optic cables (state the lenght)
Contact:
Ediseja 21, razvoj elektronskih naprav, d.o.o.
Drenov Gric 175
1360 Vrhnika
Slovenia – EU
Tel: ++386 (1) 75 05 275
grega.flander@ediseja21.com
www.ediseja21.com
Company:
Device:
Document:
Code:
Version:
Ediseja 21 CMU 100 / 2.1.6.6.6.6.6.6.6 - 12 User manual CMUMU216 V3
Date:
05.11.2014
Page:
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising