KLR SERIES - Ashly Audio
Ashly Audio, Inc. | 847 Holt Road | Webster, NY 14580-9103 USA | US toll free: +1-800-828-6308 | tel: +1-585-872-0010 | fax: +1-585-872-0739 | sales@ashly.com | www.ashly.com | Ashly is a division of Jam Industries, Ltd.
5-Year Warranty
70V Rated*
KLR uses Neutrik®
Components
klr2000
klr3200
klr4000
klr5000
KLR SERIES
The KLR Series are lightweight, high-performance
amplifiers incorporating the latest technologies delivering
quality and value at an affordable price. Whether your
application is professional audio or fixed performance
installation, KLR amplifiers are optimized to provide
reliable audio performance with sonic perfection.
Covering a power range from 1000 to 2500 Watts per
channel at 2 Ohms the KLR-2000, KLR-3200, KLR-4000
and KLR-5000 are perfectly suited for a wide range of
sound reinforcement. All four KLR amplifiers are optimized
to deliver high levels of sustained power, extraordinary
audio performance, and road-proven reliability into 2, 4,
or 8 Ohm loads and are housed in a a uniform, rugged
2RU chassis. Each KLR amplifier uses a switch mode
power supply which assures you of flawless lows, punchy
mids and pristine highs. The output topology of the
KLR-2000 is Class-AB, while the KLR-3200, 4000, and
5000 are a 2-step Class-H design.
KLR Features:
• Rated for 2 Ohms operation
• Balanced inputs via 3-pin Euroblock
• Combo XLR/TRS connectors
• Neutrik® speakON® type output connectors
• Switch-mode power supply with extensive
protection circuitry
• On/off limiter switch
• Forced-air cooled (front-in, rear-out)
• Removable dust filters, easy to clean
• Front-mounted attenuators
• Removable amp handles for permanent installation
• Optional locking front panel volume knobs
• Safety/Compliance: cCSAus, CE, FCC, RoHS
Specifications
Frequency Response
(1W @ 8 Ohms)
Damping Factor
Two-Channel, High-Performance
Power Amplifiers
Note: 0dBu = 0.775 VRMS
20Hz–20kHz (+0.3dB)
5Hz–70kHz (-3dB down point)
>380 (100Hz @ rated power @ 8 Ohms)
10dB below rated output
THD (20Hz–20kHz)
@ 4 Ohms <0.05%
Input Impedance
12k Ohm, balanced
Max Input Level
+21dBU
HPF
30Hz, 50Hz, Off (12dB/Oct)
Output Overcurrent, DC Output,
Amplifier Protection
Chassis Temperature, Mains Breaker
(KLR-5000 uses internal Mains fuse)
Operating Temp/Humidity -10C to +40C/Humidity: 0% to 90%
Front Panel
Airflow/Cooling
Front-to-Rear, Variable Speed Fan
Front Panel Indicators
Protection/Clip, Signal, Power
Attenuators
Front Panel (each channel)
Rear Panel
Input Connectors (each Ch) 3-pin Euroblock, XLR, ¼” TRS Phone Jack
Output Connectors
4-pin SpeakON® type (each channel)
3-prong NEMA 5–15, 5–20 for KLR-5000
Power Cable Connector
Weights, Dimensions & Power
19” W x 3.5” H x 16” D
Dimensions
(482mm x 88mm x 407mm)
KLR-2000: 26.2lbs (11.9kg)
KLR-3200: 26.4lbs (12kg)
Unit Weight
KLR-4000: 26.6lbs (12kg)
KLR-5000: 28lbs (12.7kg)
KLR-2000: 31lbs (14kg)
KLR-3200: 33lbs (15kg)
Shipping Weight
KLR-4000: 33lbs (15kg)
KLR-5000: 35lbs (16kg)
120VAC or 240VAC, ±10%
Power Requirements
(factory set) 50–60Hz
KLR Models
2000
3200
4000
5000
Max Output Power: Per Channel, 20Hz–20kHz, 1%THD, Both Channels Driven
2 Ohms
1,000W 1,600W 2,000W 2,500W
4 Ohms
600W 1,100W 1,400W 1,700W
8 Ohms
350W
650W
850W 1,000W
Bridge Mode, 20Hz–20kHz, 1%THD
4 Ohms
2,000W 3,200W 4,000W 6,000W
Constant Voltage Options: Per Channel, 20Hz–20kHz, 1% THD
70V
—
800W*
—
—
Line Current Draw: 120VAC 60Hz, All Channels Driven @ 4 Ohms
Idle
0.99A
0.92A
1.05A
1.14A
1/8th Power (Pink Noise)
9.7A
11.4A
14.0A
17.5A
1/3 Power (Sine Wave)
14.9A
16.6A
19.8A
24.7A
Thermal Dissipation: BTU/hr, All Channels Driven
Idle
164
136
171
215
1/8th Power (Pink Noise)
1876
2063
2489
3111
1/3 Power (Sine Wave)
2880
3001
3516
4395
Additional Specs
Signal-to-Noise
>108dB >109dB >109dB >110dB
(20Hz–20kHz, unweighted)
Input Gain Switch
1V,
20dB,
26dB
Output Circuitry
Class AB
* The KLR 3200 can also be used as a two-channel 70V distributed output amplifier providing up to 800W per channel.
©2014 All features, specifications and graphical representations are subject to change without notice.
1V,
26dB,
32dB
2-Step
Class H
1V,
26dB,
32dB
2-Step
Class H
1.4V,
26dB,
32dB
2-Step
Class H
DS-0714
Ashly Audio, Inc. | 847 Holt Road | Webster, NY 14580-9103 USA | US toll free: +1-800-828-6308 | tel: +1-585-872-0010 | fax: +1-585-872-0739 | sales@ashly.com | www.ashly.com | Ashly is a division of Jam Industries, Ltd.
KLR SERIES
Architect & Engineering Specs
KLR-2000
The two-channel power amplifier shall incorporate the latest amplifier technology to deliver a minimum power of 1,000 Watts per channel into 2 Ohm loads, 600 Watts
RMS per channel into 4 Ohm loads, or 350 Watts RMS per channel into 8 Ohm loads with both channels operating. The amplifier shall have rear panel switching for parallel
mono and bridging modes. When switched into bridged-mono mode, the amplifier shall deliver 2,000 Watts into a 4 Ohm load. The amplifier protection shall include
output over-current, DC output, chassis temperature, and a mains circuit-breaker. Frequency response shall be 20Hz–20kHz (1W @ 8 Ohms). The Signal-to-Noise Ratio shall
be greater than 108dB at rated power into 8 Ohms (unweighted). THD shall be less than 0.05% into 4 Ohms, 20Hz–20kHz and 10dB below rated power. The amplifier shall
have a channel attenuator for each input on the front panel and input sensitivity select switch, a high-pass filter switch and limiter enable switch on the rear panel. The
inputs shall be of balanced bridging type with XLR, ¼” TRS, and 3-pin Euroblock connectors. The outputs shall be four pin SpeakON type connectors. LED type indicators
shall be employed to show the relative power level of each channel, clip/protect and power on/off. Self contained forced air cooling (front in) shall be used with front panel
mounted, removable dust filters. The power amplifier shall weigh 26.2lbs/11.9kg net and mount in a standard 19 inch rack using two spaces (3.5 inches high). The power
requirement shall be 120VAC or 240VAC ±10%, 50–60Hz, factory set.
The power amplifier shall be the Ashly KLR-2000.
KLR-3200
The two-channel power amplifier shall incorporate the latest amplifier technology to deliver a minimum power of 1,600 Watts per channel into 2 Ohm loads, 1,100 Watts
RMS per channel into 4 Ohm loads, or 650 Watts RMS per channel into 8 Ohm loads with both channels operating. The amplifier shall have rear panel switching for parallel
mono and bridging modes. When switched into bridged-mono mode, the amplifier shall deliver 3,200 Watts into a 4 Ohm load. The amplifier protection shall include
output over-current, DC output, chassis temperature, and a mains circuit-breaker. Frequency response shall be 20Hz–20kHz (1W @ 8 Ohms). The Signal-to-Noise Ratio shall
be greater than 109dB at rated power into 8 Ohms (unweighted). THD shall be less than 0.05% into 4 Ohms, 20Hz–20kHz and 10dB below rated power. The amplifier shall
have a channel attenuator for each input on the front panel and input sensitivity select switch, a high-pass filter switch and limiter enable switch on the rear panel. The
inputs shall be of balanced bridging type with XLR, ¼” TRS, and 3-pin Euroblock connectors. The outputs shall be four pin SpeakON type connectors. LED type indicators
shall be employed to show the relative power level of each channel, clip/protect and power on/off. Self contained forced air cooling (front in) shall be used with front panel
mounted, removable dust filters. The power amplifier shall weigh 26.4lbs/12kg net and mount in a standard 19 inch rack using two spaces (3.5 inches high). The power
requirement shall be 120VAC or 240VAC ±10%, 50–60Hz, factory set.
The power amplifier shall be the Ashly KLR-3200.
KLR-4000
The two-channel power amplifier shall incorporate the latest amplifier technology to deliver a minimum power of 2,000 Watts per channel into 2 Ohm loads, 1,400 Watts
RMS per channel into 4 Ohm loads, or 850 Watts RMS per channel into 8 Ohm loads with both channels operating. The amplifier shall have rear panel switching for parallel
mono and bridging modes. When switched into bridged-mono mode, the amplifier shall deliver 4,000 Watts into a 4 Ohm load. The amplifier protection shall include
output over-current, DC output, chassis temperature, and a mains circuit-breaker. Frequency response shall be 20Hz–20kHz (1W @ 8 Ohms). The Signal-to-Noise Ratio shall
be greater than 109dB at rated power into 8 Ohms (unweighted). THD shall be less than 0.05% into 4 Ohms, 20Hz–20kHz and 10dB below rated power. The amplifier shall
have a channel attenuator for each input on the front panel and input sensitivity select switch, a high-pass filter switch and limiter enable switch on the rear panel. The
inputs shall be of balanced bridging type with XLR, ¼” TRS, and 3-pin Euroblock connectors. The outputs shall be four pin SpeakON type connectors. LED type indicators
shall be employed to show the relative power level of each channel, clip/protect and power on/off. Self contained forced air cooling (front in) shall be used with front panel
mounted, removable dust filters. The power amplifier shall weigh 26.7lbs/12.1kg net and mount in a standard 19 inch rack using two spaces (3.5 inches high). The power
requirement shall be 120VAC or 240VAC ±10%, 50–60Hz, factory set.
The power amplifier shall be the Ashly KLR-4000.
KLR-5000
The two-channel power amplifier shall incorporate the latest amplifier technology to deliver a minimum power of 2,500 Watts per channel into 2 Ohm loads, 1,700 Watts
RMS per channel into 4 Ohm loads, or 1,000 Watts RMS per channel into 8 Ohm loads with both channels operating. The amplifier shall have rear panel switching for parallel mono and bridging modes. When switched into bridged-mono mode, the amplifier shall deliver 5,000 Watts into a 4 Ohm load. The amplifier protection shall include
output over-current, DC output, chassis temperature, and an internal mains fuse. Frequency response shall be 20Hz–20kHz (1W @ 8 Ohms). The Signal-to-Noise Ratio shall
be greater than 110dB at rated power into 8 Ohms (unweighted). THD shall be less than 0.05% into 4 Ohms, 20Hz–20kHz and 10dB below rated power. The amplifier shall
have a channel attenuator for each input on the front panel and input sensitivity select switch, a high-pass filter switch and limiter enable switch on the rear panel. The
inputs shall be of balanced bridging type with XLR, ¼” TRS, and 3-pin Euroblock connectors. The outputs shall be four pin SpeakON type connectors. L.E.D type indicators
shall be employed to show the relative power level of each channel, clip/protect and power on/off. Self contained forced air cooling (front in) shall be used with front panel
mounted, removable dust filters. The power amplifier shall weigh 28.2lbs/12.8kg net and mount in a standard 19 inch rack using two spaces (3.5 inches high). The power
requirement shall be 120VAC or 240VAC ±10%, 50–60Hz, factory set.
The power amplifier shall be the Ashly KLR-5000.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising