Worx | WX312.1 | Instruction manual | Worx WX312.1 Instruction manual

Worx WX312.1 Instruction manual
SAFETY AND OPERATING MANUAL
Impact drill
WX312 WX312.1
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool
1 Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
2
2 Electrical safety
a) Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
Impact drill
electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected
supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying
the tool. Carrying power tools with your
finger on the switch or energising power
tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your
hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use
of these devices can reduce dust-related
hazards.
WX312 WX312.1
4) Power tool use and care
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will do
the job better and safer at the rate for which
it was designed.
b) Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preventive
safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power tool
or these instructions to operate the
power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Impact drill
ADDITIONAL SAFETY
POINTS FOR YOUR DRILL
1. Wear ear protectors when impact
drilling. Exposure to noise can cause
hearing loss.
2. Use auxiliary handle(s), if supplied
with the tool. Loss of control can cause
personal injury.
3. Hold power tool by insulated
gripping surfaces, when performing
an operation where the cutting
accessory may contact hidden wiring
or its own cord. Cutting accessory
contacting a “live” wire may make
exposed metal parts of the power tool
“live” and could give the operator an
electric shock.
4. Always wear safety goggles or eye
protection when using this tool.
Use a dust mask or respirator for
applications which generate dust.
5. Secure the material being drilled.
Never hold it in your hand or across
legs. Unstable support can cause the drill
bit to bind causing loss of control and
injury.
6. Disconnect battery pack from tool
or place the switch in the locked
or off position before making any
assembly, adjustments or changing
accessories. Such preventive safety
measures reduce the risk of starting the
tool accidentally.
7. Position yourself to avoid being
caught between the tool or side
handle and walls or post. Should the
bit become bound or jammed in the work,
the reaction torque of the tool could crush
your hand or leg.
8. If the bit becomes bound in the
workpiece, release the trigger
immediately, reverse the direction
of rotation and slowly squeeze the
trigger to back out the bit. Be ready
for a strong reaction torque. The drill body
will tend to twist in the opposite direction
as the drill bit is rotating.
9. Do not grasp the tool or place your
hands too close to the spinning
WX312 WX312.1
3
4
chuck or drill bit. Your hand may be
lacerated.
10. When installing a drill bit, insert the
shank of the bit well within the jaws
of the chuck. If the bit is not inserted
deep enough, the grip of the jaws over
the bit is reduced and the loss of control
is increased.
11. Do not use dull or damaged bits
and accessories. Dull or damaged bits
have a greater tendency to bind in the
workpiece.
12. When removing the bit from the
tool avoid contact with skin and
use proper protective gloves when
grasping the bit or accessory.
Accessories may be hot after prolonged
use.
13. Check to see that keys and adjusting
wrenches are removed from the drill
before switching the tool “ON”. Keys
or wrenches can fly away at high velocity
striking you or bystander.
14. Do not run the dill while carrying it
at your side. A spinning drill bit could
become entangled with clothing and
injury may result.
15. Avoid bouncing and snagging the
wheels, discs or brushes especially
when working corners, sharp edges,
etc. This can cause loss of control and
kickback.
16. Position the tether clear of rotating
bit. Do not wrap the tether around
your arm or wrist. If you lose control
and have the tether wrapped around your
arm or wrist, it may entrap you and cause
injury.
Impact drill
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
Double insulation
Warning
Wear ear protection
Wear eye protection
Wear dust mask
RCM approval mark
WX312 WX312.1
1
2
3
9
4
6
8
Impact drill
5
7
WX312 WX312.1
5
1 CHUCK (WX312)
2 DEPTH GAUGE
3 DRILL/ HAMMER DRILL FUNCTION SELECTOR
4
FORWARD AND REVERSE ROTATION CONTROL LEVER
5 SWITCH LOCK ON BUTTON
6 VARIABLE SPEED CONTROL
7 ON/OFF SWITCH
8 AUXILIARY HANDLE
9 KEYLESS CHUCK(WX312.1)
* Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA
WX312 WX312.1
Voltage
230-240V~50Hz
Power input
6
810W
No load speed
0-2800/min
Impact rate
0-44800/min
Chuck capacity
Drilling capacity
13mm
Masonry
16mm
Wood
32mm
Steel
13mm
Protection class
/II
Machine weight
2.42kg
ACCESSORIES
Auxiliary handle Depth gauge
Chuck key (WX312)
HSS drill bit : 5, 6, 8mm ( Each 1 pc WX312.1)
Masonry drill bit : 6, 8,10mm (Each 1 pc WX312.1)
1
1
3
3
3
We recommend that you purchase your accessories from the same store that sold you the
tool. Use good quality accessories marked with a well-known brand name. Choose the type
according to the work you intend to undertake. Refer to the accessory packaging for further
details. Store personnel can assist you and offer advice.
Impact drill
WX312 WX312.1
OPERATION
1
NOTE: Before using the
tool, read the instruction
2
book carefully.
INTENDED USE
The machine is intended for impact drilling in brick,
concrete and stone as well as for drilling
a in wood,
metal and plastic.
C2(See Fig. A)
1. AUXILIARY HANDLE
Slide the handle onto the drill and rotate to the desired
working position. To clamp the auxiliary handle
rotates the handgrip clockwise. To loosen the auxiliary
2
handle rotate the hand grip anti-clockwise. Always use
the auxiliary handle.
1
WARNING! Always check and rotate the
handle tightly before using to avoid any
accident.
2. INSTALLING THE DEPTH GAUGE
(See Fig. B)
The depth gauge can be used to set a constant depth
to drill. To use the depthC3
gauge, loosen the handle by
rotating the bottom section of handle anti-clockwise.
Insert the depth gauge through hole in handle. Slide
the depth gauge to required depth and tighten fully.
3. INSERTING A TOOL INTO CHUCK
(See Fig. C1, C2, C3)
KEY CHUCK (1) (WX312)
1
2
Remove chuck key from key storage tab at base
of drill
handle, place key into chuck, turn key anti-clockwise to
undo/loosen chuck, inset drill/tool and firmly tighten
chuck by turning key clockwise. Remove key and
replace in storage tab at base of drill handle.
D
(See Fig. C1)
A
B
7
C1
E
Impact drill
WX312 WX312.1
KEYLESS CHUCK (9) (WX312.1)
First pull the locking sleeve (a) backward until you
hear a “click” sound. Then, while holding the locking
sleeve, rotate and loosen the front section of the
chuck to open the chuck jaws. Insert the drill bit into
the chuck jaws, and while holding the locking sleeve,
rotate and tighten the front section in the opposite
direction. Ensure that the drill bit is in the center of the
chuck jaws. Finally, push the locking sleeve forward
until you hear a “click” sound. Your drill bit is now
A
locked in the chuck. (See Fig. C2,C3)
1
2
a
C2
4. ON/OFF SWITCH
Depress the switch to start the tool and release it to
stop your tool.
2
1
5. SWITCH LOCK-ON BUTTON (See Fig. D)
Depress on/off switch then lock-on button, release on/
off switch first and lock-on button second. Your switch
is now locked on for continuous use. To switch off
your tool just depress and release the on/off switch.
6.
B VARIABLE SPEED CONTROL
(See Fig. E)
Adjust the variable speed control to increase or
decrease the speed according to the material and
accessory to be used (also possible during no load
operation). Low speed will provide low torque and
high speed gives higher torque.
C3
8
1
2
D
C1
E
Impact drill
WX312 WX312.1
7. FORWARD AND REVERSE ROTATION
CONTROL (See Fig. F)
For drilling use forward rotation marked “
”
(lever is moved to the left). Only use reverse rotation
marked “
” (lever is moved to the right) to remove
screws or release a jammed drill bit.
NOTE: Never move the forward/reverse switch
whilst the drill in operation or the on/off switch
is locked as this will damage the drill.
8. HAMMER OR DRILLING CONTROL (See G)
When drilling masonry and concrete push the drill/
impact action selector switch into the hammer
position “ ”. When drilling wood, metal, plastic
push the switch into the drill position “ ”.
F
G
9
Impact drill
WX312 WX312.1
WORKING HINTS FOR YOUR
DRILL
10
1. Drilling masonry and concrete
Select the drill/impact action selector switch
to the “hammer symbol” position. Tungsten
carbide drill bits should always be used for
drilling masonry, concrete etc with a high
speed.
2. Drilling steel
Select the drill/impact action selector switch
to the “drill symbol” position. HSS drill bits
should always be used for drilling steel with a
lower speed.
3. Pilot holes
When drilling a large hole in tough material
(i.e. steel), we recommend drilling a small
pilot hole first before using a large drill bit.
4. Drilling tiles
Select the drill/impact action selector switch
to the “drill symbol” position to drill the tile.
When tile has been penetrated, switch over to
“hammer symbol” position.
5. Cool the motor
If your power tool becomes too hot, set the
speed to maximum and run no load for 2-3
minutes to cool the motor.
TROUBLESHOOTING
1. If your power tool does not start, check the
plug on the power supply first.
2. If the drill doesn’t work properly, check the
drill bit for sharpness, replace drill bit if
worn. Check that the drill is set to forward
rotation for normal use.
3. If a fault can not be rectified, return the tool
to an authorized dealer for repair.
MAINTENANCE
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional
lubrication or maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order to
avoid a hazard.
Impact drill
WX312 WX312.1
Copyright © 2014, Positec. All Rights Reserved.
2SDI104PK11002A4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising