Bayliner | 2452 Classic Cruiser | Specifications | Bayliner 2452 Classic Cruiser Specifications

Bayliner 2452 Classic Cruiser Specifications
Engine Serial Number: _____________________________________________
Hull Identification Number:__________________________________________
Hull Identification Number
• The Hull Identification Number (HIN) is
located on the starboard side of the transom.
• Record the HIN (and the engine serial numbers) in the space provided above.
• Include the HIN with any correspondence
or orders.
HIN LOCATION
© 2003 Bayliner Technical Publications. All rights reserved.
No part of this publication may be reproduced, stored in any retrieval system, or transmitted in any form by any means, electronic, mechanical, photocopying,
recording or otherwise, without prior written permission of Bayliner.
Printed in the United States of America.
General Notes
The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Bayliner assumes no liability resulting from errors or omissions in this document, or from the use of information contained herein.
Due to our commitment to product improvement, Bayliner reserves the right to make changes in the product design, specifications, and equipment at any time
without notice or obligation. Illustrations and/or photos may show optional equipment.
All Bayliner products meet or exceed USCG (Unites States Coast Guard) and/or NMMA (National Marine Manufacturer’s Association) construction standards.
Manufactured with 1,1,1 Trichloroethane, a substance which harms public health and environment during the manufacturing process by destroying ozone in the
upper atmosphere.
Proprietary Rights
This document discloses subject matter in which Bayliner has proprietary rights. The information and design disclosed herein were originated by and are the property of Bayliner. Neither receipt nor possession thereof confers or transfers any right to reproduce, copy, alter or disclose the document or any part thereof, any
information contained therein, or to construct boats or any item from it, except by written permission from or written agreement with Bayliner. This document is to
be returned upon request to Bayliner.
CONTENTS
1
Chapter 1: Welcome Aboard!
13
Chapter 3: Propulsion &
Related Systems
1
Dimensions and Tank Capacities
1
Layout View
13
Engine
1
Dealer Service
13
Engine Room Ventilation System
1
Warranty Information
14
2
Boating Experience
2
Engine & Accessories Guidelines
2
Engine & Accessories Literature
2
Structural Limitations
3
Fuel System
15 Fuel Fill and Vent
15 Fuel Filters
15 Anti-siphon Valve
16
Quick Oil Drain System
Safety Standards
17
Chapter 4: Controls
3
Qualified Maintenance
17
Steering
4
Special Care For Moored Boats
17
Shift/Throttle
4
Sacrificial Anodes (Zincs)
17
Power Trim and Tilt
5
Carbon Monoxide (CO)
18
Trim Tabs (If Equipped)
19
Chapter 5: Navigation &
Communication Equipment
19
VHF Radio (If Equipped)
19
Compass (If Equipped)
20
Chapter 6: Plumbing
5
6
6
7
7
7
7
8
9
9
12
Facts about CO
Where and How CO Can Accumulate
How to Protect Yourself and Others From CO
Trip Checklist
Monthly Checklist
Annual Checklist
Carbon Monoxide Alarm System
More Information
Chapter 2: Locations
20
Bilge Pumps
22 Autofloat Switches
Exterior Views
9 Hull Views
10 Deck View
11 Helm
23
Component Locations
24
Seawater Systems
23 Seacocks
23 Seawater Strainers
Freshwater System
25
25
26
26
27
Freshwater System Winterization
Transom Shower (If Equipped)
Water Heater
Winterizing the Water Heater
Drain Systems
27 Sink Drains
27 Deck Drains
28
28
Portable Toilet (If Equipped)
Marine Head with Holding Tank (If Equipped)
28 Winterizing The Marine Head
29 Macerator (If Equipped)
30
Chapter 7: Deck Equipment
36
Chapter 12: Electrical System
30
Cleats and Tow Eyes
37
12-Volt DC System
31
Chapter 8: Appliances &
Entertainment Systems
31
Refrigerator (If Equipped)
31
Microwave Oven (If Equipped)
31
Electric Stove (If Equipped)
32
Alcohol/Electric Stove (If Equipped)
32
Audio & Visual Equipment
33
Chapter 9: Convertible Seats,
Beds, & Tables
33
Dinette/Berth
34
Chapter 10: Lights
34
Care and Maintenance
34
Navigation Lights
34
Interior & Exterior Lights
35
Chapter 11: Air Conditioning
(If Equipped)
35
Air Conditioning System (If Equipped)
37
37
37
37
38
38
38
39
Batteries
Fuses and Circuit Breakers
Battery Switch
Battery Switch Positions
Alternator
Battery Charger (If Equipped)
12-Volt Accessory Outlet
120-Volt AC System (If Equipped)
40 Shore Power
42 Connecting To Shore Power
43 Transfer Switch (If Equipped with Dual
Shore Power)
44
Electrical Routings
44
44
45
45
46
47
Hull Electrical Harness
Deck Electrical Harness.
120 Volt AC System (If Equipped)
Battery System
Bonding Harness
Wire Diagrams
47 Engine Electrical System
48 Single Dockside
49 Dual Dockside
50
Important Records
51
Float Plan
Hazard Boxes & Symbols
The hazard boxes and symbols shown below are used throughout this Supplement to call attention to potentially dangerous situations which could lead to either personal injury or product damage. Read ALL warnings carefully and
follow all safety instructions.
!
DANGER!
This box alerts you to immediate hazards which WILL cause severe personal injury or death if
the warning is ignored.
!
WARNING!
This box alerts you to hazards or unsafe practices which COULD result in severe personal
injury or death if the warning is ignored.
!
CAUTION!
This box alerts you to hazards or unsafe practices which COULD result in minor personal
injury or cause product or property damage if the warning is ignored.
NOTICE
This box calls attention to installation, operation or maintenance information, which is important to proper operation but is not hazard related.
FIRE
HAZARD!
EXPLOSION
HAZARD!
FALLING
HAZARD!
NO OPEN
FLAME!
ROTATING
PROPELLER HAZARD!
ELECTRICAL
HAZARD!
HOT
HAZARD!
RUN BILGE BLOWERS
FOR 4 MINUTES!
CO POISONING
HAZARD!
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
This Owner’s Manual Supplement provides specific information about your boat that is not covered in the Cruiser &
Yacht Owner’s Manual. Please study the Cruiser & Yacht Owner’s Manual and this Supplement carefully. Keep the
Cruiser & Yacht Owner’s Manual and this Supplement on your boat in a secure, yet readily available place.
Dimensions and Tank Capacities
Overall
Bridge
Draft
Draft (Drive
Length Clearance Beam (Drive Up)
Down)
23' 9"
8' 9.5"
8' 6"
1'8. 5"
Fuel Capacity
(gal.)
3' 5"
Freshwater
Waste Holding
Capacity (gal.) Tank Capacity (gal.)
80
20
20
Layout View
folding
seat
portapotty
step
stowage
under
sink
stove
stowage
folding
helm seat
stowage
under
dinette
converts stowage
to double under
berth
icebox
under
V-berth
stowage
under
Dealer Service
•
•
•
•
•
Ask your dealer to explain all systems before taking delivery of your boat.
Your dealer is your key to service.
Contact your dealer if you have any problems with your new boat.
If your dealer cannot help, call our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235.
Buy replacement parts from any authorized Bayliner dealer.
Warranty Information
• Bayliner offers a Limited Warranty on each new Bayliner purchased through an authorized Bayliner dealer.
• A copy of the Limited Warranty was included in your owner’s packet.
• If you did not receive a copy of the Limited Warranty, please contact your dealer or call 360-435-8957 for a copy.
1
Chapter 1: Welcome Aboard!
2452 Classic Cruiser • Owner’s Manual Supplement
Boating Experience
!
WARNING!
CONTROL HAZARD!
A qualified operator must be in control of the boat at all times. DO NOT operate your boat
while under the influence of alcohol or drugs.
If this is your first boat or if you are changing to a type of boat you are not familiar with, for your own comfort and
safety, obtain handling and operating experience before assuming command of the boat.
Take one of the boating safety classes offered by the U.S. Power Squadrons or the U.S. Coast Guard Auxiliary. For
more course information, including dates and locations of upcoming classes, contact the organizations directly:
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
Outside the United States, your selling dealer, national sailing federation or local boat club can advise you of local
sea schools or competent instructors.
Engine & Accessories Guidelines
NOTICE
When storing your boat please refer to your engine’s operation and maintenance manuals.
• Your boat’s engine and accessories were selected to provide optimum performance and service.
• Installing a different engine or other accessories may cause unwanted handling characteristics.
• Should you choose to install a different engine or to add accessories that will affect the boat’s running trim, have
an experienced marine technician perform a safety inspection and handling test before operating your boat again.
Certain modifications to your boat can result in cancellation of your warranty protection. Always check with
your dealer before making any modifications to your boat.
Engine & Accessories Literature
• The engine and accessories installed on your boat come with their own operation and maintenance manuals.
• Read and understand these manuals before using the engine and accessories.
• Unless noted otherwise, all engine and accessory literature referred to in this Supplement is included in your
owner’s packet.
Structural Limitations
The transom platform and bow platform are designed to be lightweight for proper boat balance. The load limit for
these platforms is 30 pounds per square foot, evenly distributed.
2
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Safety Standards
!
DANGER!
FALLING and ROTATING PROPELLER HAZARD!
NEVER allow anyone to ride on parts of the boat not designed for
such use.
• Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding or occupying the transom platform while underway is especially hazardous and will cause personal
injury or death.
!
DANGER!
ROTATING PROPELLER and CARBON MONOXIDE
POISONING HAZARD!
• NEVER allow anyone to occupy, or hang from, the
back deck or swim platform while the engine(s)
are running.
• Teak surfing, dragging, or water skiing within 20 feet
of a moving watercraft can be fatal.
!
DANGER!
PERSONAL SAFETY HAZARD!
ALWAYS secure the anchor and other loose objects before getting underway. The anchor and
other items that are not properly secured can come loose when the boat is moving and cause
personal injury or death.
• Your boat’s mechanical and electrical systems were designed to meet safety standards in effect at the time it
was built.
• Some of these standards were mandated by law, all of them were designed to insure your safety, and the safety of
other people, vessels and property.
In addition to this Owner’s Manual Supplement, please read the Cruiser & Yacht Owner’s Manual and all accessory
instructions for important safety standards and hazard information.
Qualified Maintenance
!
WARNING!
To maintain the integrity and safety of your boat, allow only qualified personnel to perform
maintenance on, or in any way modify: The steering system, propulsion system, engine control
system, fuel system, environmental control system, electrical system or navigational system.
• Failure to maintain your boat’s systems (listed in the warning above) as designed could violate the laws in your
jurisdiction and could expose you and other people to the danger of bodily injury or accidental death.
• Follow the instructions provided in the Cruiser & Yacht Owner’s Manual, this Owner’s Manual Supplement, the
engine owner’s manual and all accessory instruction sheets and manuals.
3
Chapter 1: Welcome Aboard!
2452 Classic Cruiser • Owner’s Manual Supplement
Special Care For Moored Boats
NOTICE
• To help seal the hull bottom and reduce the possibility of gelcoat blistering on moored boats,
apply an epoxy barrier coating. The barrier coating should be covered with several coats of
anti-fouling paint.
• Many states regulate the chemical content of bottom paints in order to meet environmental
standards. Check with your local dealer about recommended bottom paints, and about the
laws in effect in your area.
• Whether moored in saltwater or freshwater, your boat will collect marine growth on its hull bottom.
• This will detract from the boat’s beauty, greatly affect its performance and may damage the gelcoat.
• Periodically haul the boat out of the water and scrub the hull bottom with a bristle brush and a solution of soap
and water.
Sacrificial Anodes (Zincs)
NOTICE
Do not paint between the zinc and the metal surface it contacts and do not paint over the zincs.
Your boat is equipped with sacrificial anodes (zincs) to protect underwater metal parts from excessive deterioration.
Check the zincs regularly and replace them if they have deteriorated more than 70%.
There are many factors that affect the rate at which the zincs deteriorate, including:
• Water temperature
• Salinity
• Water pollution
Stray electrical current from the boat or dock may cause complete deterioration in just a few weeks. If there is rapid
zinc deterioration, measure the electrolytic corrosion around your boat with a Corrosion Test Meter. If the zincs are
not bonded correctly, they will not provide protection.
4
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Carbon Monoxide (CO)
!
DANGER!
• Carbon monoxide gas (CO) is colorless, odorless, tasteless, and
extremely dangerous.
• All engines, generators, and fuel burning appliances produce CO
as exhaust.
• Prolonged exposure to low concentrations or very quick exposure to high
concentrations will cause BRAIN DAMAGE or DEATH.
• Teak surfing, dragging, or water skiing within 20 feet of a moving watercraft can be fatal.
Facts about CO
• CO poisoning causes a significant number of boating deaths each year.
• Called the "silent killer", CO is an extremely toxic, colorless, odorless and tasteless gas.
• CO can harm or even kill you inside or outside your boat.
• CO can affect you whether you’re underway, moored, or anchored.
• CO symptoms are similar to seasickness or alcohol intoxication.
• CO can make you sick in seconds. In high enough concentrations, even a few breaths can be fatal.
• Breathing CO blocks the ability of your blood to carry oxygen.
• The effects are cumulative, even low levels of exposure can result in injury or death.
Factors That Increase the Effects of CO Poisoning
• Age
• Smokers or people exposed to high concentrations of cigarette smoke
• Consumption of alcohol
• Lung disorders
• Heart problems
• Pregnancy
5
Chapter 1: Welcome Aboard!
2452 Classic Cruiser • Owner’s Manual Supplement
Where and How CO Can Accumulate
Stationary Conditions That Increase CO Accumulations Include:
A. Using engine, generator, or other fuel burning device when boat is moored in a confined space.
B. Mooring too close to another boat that is
using its engine, generator, or other fuel
burning device.
To correct stationary situations A and/or B:
• Close all windows, portlights and hatches.
• If possible, move your boat away from source of CO.
Running Conditions That Increase CO Accumulations Include:
C. Running boat with trim angle of bow too high.
D. Running boat without through ventilation (station wagon effect).
To correct running situations C and/or D:
• Trim bow down.
• Open windows and canvas.
• When possible, run boat so that prevailing winds help dissipate exhaust.
How to Protect Yourself and Others From CO
• Know where and how CO may accumulate in and around your boat (see above).
• Maintain fresh air circulation throughout the boat at all times.
• Know where your engine and generator exhaust outlets are located and keep everyone away from these areas.
• Never sit on, or hang onto, the back deck or swim platform while the engine(s) are running.
• Never enter the areas under swim platforms where exhaust outlets are located.
• Although CO can be present without the smell of exhaust fumes, if exhaust fumes are detected on the boat, take
immediate action to dissipate these fumes.
• Treat symptoms of seasickness as possible CO poisoning. Get the person into fresh air immediately. Seek medical
attention—unless you’re sure it’s not CO.
• Install and maintain CO alarms inside your boat. Do not ignore any alarm. Replace alarms as recommended by the
alarm manufacturer.
• Follow the checklists provided on the next page.
• Get a Vessel Safety Check.
For information on how to get a free VESSEL SAFETY CHECK, visit www.vesselsafetycheck.org or contact your
local U.S. Coast Guard Auxiliary or United States Power Squadrons®.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
6
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 1: Welcome Aboard!
Trip Checklist
❏ Make sure you know where the exhaust outlets are located on your boat.
❏ Educate all passengers about the symptoms of CO poisoning and where CO may accumulate.
❏ When docked, or rafted with another boat, be aware of exhaust emissions from the other boat.
❏ Confirm that water flows from the exhaust outlet when the engines and generator are started.
❏ Listen for any change in exhaust sound, which could indicate an exhaust component failure.
❏ Test the operation of each CO alarm by pressing the test button.
Monthly Checklist
❏ Make sure all exhaust clamps are in place and secure.
❏ Look for exhaust leaking from exhaust system components. Signs include rust and/or black streaking, water
leaks, or corroded or cracked fittings.
❏ Inspect rubber exhaust hoses for burned, cracked, or deteriorated sections. All rubber hoses should be pliable and
free of kinks.
Annual Checklist
Have a Qualified Marine Technician:
❏ Replace exhaust hoses if cracking, charring, or deterioration is found.
❏ Ensure that your engines and generators are properly tuned, and well maintained.
❏ Inspect each water pump impeller and the water pump housing. Replace if worn. Make sure cooling systems are
in working condition.
❏ Inspect all metallic exhaust components for cracking, rusting, leaking, or loosening. Make sure they check the
cylinder head gasket, exhaust manifold, water injection elbow, and the threaded adapter nipple between the manifold and the elbow.
❏ Clean, inspect, and confirm proper operation of the generator cooling water anti-siphon valve (if equipped).
Carbon Monoxide Alarm System
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• The house battery switch must be in the On position for the CO Monitors
to work.
NOTICE
The stereo memory and CO monitor(s) place a small, but constant drain on the battery. If your
boat will be unattended for an extended amount of time, plug into shore power with the battery
charger turned On, or disconnect the battery if shore power is not an option.
• Your boat features a carbon monoxide (CO) alarm system.
• Do not disconnect the alarm system.
• Read and understand the manufacturer’s instructions for your CO alarm system. If you did not receive an instruction manual, call (800) 383-0269 and one will be mailed to you.
If your boat is not equipped with a carbon monoxide alarm, consider purchasing one from your dealer or marine
supply store.
7
Chapter 1: Welcome Aboard!
2452 Classic Cruiser • Owner’s Manual Supplement
More Information
For more information about how you can prevent carbon monoxide poisoning on recreational boats and other ways to
boat more safely, contact:
United States Coast Guard
Office of Boating Safety (G-OPB-3)
2100 Second Street SW
Washington, DC 20593
www.uscgboating.org
1-800-368-5647
National Marine Manufacturers
Association (NMMA)
200 East Randolph Drive
Suite 5100
Chicago, IL 60601-9301
www.nmma.org
312-946-6200
American Boat & Yacht Council,
Inc. (ABYC)
3069 Solomon’s Island Road
Edgewater, MD 21037-1416
www.abycinc.org
410-956-1050
For information on how to get a free VESSEL SAFETY CHECK, visit www.vesselsafetycheck.org or contact your
local U.S. Coast Guard Auxiliary or United States Power Squadrons®.
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
8
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 2: Locations
Exterior Views
Hull Views
AFT BILGE
PUMP DRAIN
DECK
DRAINS
WATER
TANK VENT
WASTE
TANK VENT
ROPE LOCKER
DRAIN
DECK
DRAINS
STARBOARD HULLSIDE
MACERATOR OVERBOARD
DISCHARGE (IF EQUIPPED)
FWD BILGE
PUMP DRAIN
BOW EYE
PORT HULLSIDE
SINK DRAIN
DECK DRAINS
TRANSOM
VIEW
TRIM TAB
(TYPICAL PORT & STBD)
GARBOARD
DRAIN
STERN EYES
SWIM
PLATFORM
9
Chapter 2: Locations
2452 Classic Cruiser • Owner’s Manual Supplement
Deck View
SHORE POWER
INLET(S)
NAVIGATION LIGHT
(TYPICAL PORT & STBD)
HAWSE PIPE
ANCHOR ROLLER
DECK
CLEAT (TYPICAL)
WASTE PUMP-OUT
FITTING (IF EQUIPPED)
WATER FILL
FITTING
FUEL FILL
FITTING
10
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 2: Locations
Helm
VIEW OF THE HELM LOOKING FORWARD
TACHOMETER
DEPTH SOUNDER
GAUGE (IF EQUIPPED)
SPEEDOMETER
WINDSHIELD
WIPER
FWD BILGE
PUMP
AFT BILGE
PUMP
HORN
BILGE
BLOWERS
INSTRUMENT
LIGHT
ANCHOR
LIGHT
NAVIGATION
LIGHTS
TRIM TAB
SWITCHES
ENGINE
IGNITION
ACCESSORY
CIRCUIT
BREAKERS
ACCESSORIES
FUEL
GAUGE
VOLTAGE
GAUGE
TEMPERATURE
GAUGE
OIL PRESSURE
GAUGE
TRIM GAUGE
TYPICAL HELM LAYOUT SHOWN
ACTUAL LAYOUT MAY VARY DEPENDING
ON ENGINE AND ACCESSORY OPTIONS
11
Chapter 2: Locations
2452 Classic Cruiser • Owner’s Manual Supplement
Component Locations
12-Volt Accessory Outlet: At the helm on the dash panel.
Air Conditioner Seawater Intake Seacock: Under the cabin entry step.
Air Conditioner Unit: In the V-berth. Access is through the starboard aft V-berth hatch.
Battery: On the starboard side of the engine room, aft of the battery charger.
Battery Charger: On the starboard side of the engine room.
Battery Switch: Inside the storage compartment, under the helm seat.
Bilge pump - Aft: In the engine compartment.
Bilge pump - Forward: Under cabin entry step.
Carbon Monoxide Detector: In the cabin on the starboard aft dinette wall.
DC Circuit Breakers: At the helm, under the dash.
Engine Circuit Breaker: On the engine.
Fuel Fill: On the starboard aft corner of the deck.
Fuel Tank: In the engine compartment forward of the engine.
Macerator Underwater Discharge Seacock: Inside the engine room.
Navigation Lights: Red and green lights at the bow. White all-around light on the hardtop.
Waste Holding Tank: Access is through the center floor hatch in the cockpit.
Water Fill: On the starboard side deck.
Water Heater: In the center floor hatch in the cockpit, to the left of the holding tank.
Water Pump: Inside the center floor hatch in the cockpit, next to the water/holding tanks.
Water Pump Switch: Inside the cabin, at the galley, to the left of the galley faucet.
Water Tank: Access is through center floor hatch in the cockpit.
12
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Engine
The owner’s packet contains detailed engine operation and maintenance manuals. Be sure to read and understand
these manuals before starting or doing any maintenance on the engine.
Engine Room Ventilation System
!
•
•
•
•
WARNING!
FIRE/EXPLOSION HAZARD
Use of the blower system is NOT A GUARANTEE that explosive fumes have been removed.
If you smell fuel, DO NOT start the engine and DO NOT turn on any electrical devices.
If you smell fuel and the engine is already running, SHUT OFF the engine and TURN OFF
all electrical devices. Investigate immediately.
DO NOT obstruct or modify the ventilation system.
BILGE BLOWER SYSTEM
BLOWER
HOSES
BLOWER
• The bilge blower removes explosive fuel fumes from the engine compartment.
• Fresh air is drawn into the compartment through the deck vents.
• The bilge blower switch is at the helm.
To make sure the engine compartment is ventilated with fresh air, run the bilge blower:
• For at least four minutes before starting the engine.
• During starting.
• Anytime your boat is running below cruising speed.
13
Chapter 3: Propulsion & Related Systems
2452 Classic Cruiser • Owner’s Manual Supplement
Fuel System
!
WARNING!
FIRE, EXPLOSION AND OPEN FLAME HAZARD!
• It is very important that the fuel system be inspected thoroughly the first time it is filled and
at each subsequent filling.
• The fueling instructions in the Cruiser & Yacht Owner’s Manual and the fuel recommendations in the engine operation manual must be followed.
!
CAUTION
Avoid the storage or handling of gear near the fuel lines, fittings and tank.
FUEL SYSTEM ROUTING
FUEL FILL
DECK FITTING
FUEL TANK
FUEL TANK
VENT FITTING
FUEL FEED
HOSE
14
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 3: Propulsion & Related Systems
Fuel Fill and Vent
• The fuel fill fitting is marked “GAS”.
• The fuel tank vent is located below the fuel fill.
• If you experience difficulty filling the fuel tank, check to see if the fuel fill hose or vent hose is kinked or collapsed. If there are no visible signs of a problem, contact your local dealer.
Fuel Filters
• The fuel pickup tube (located inside the fuel tank) is equipped with a fine mesh screen filter.
• Also, when supplied by the engine manufacturer, a fuel filter is installed on the engine.
• Periodically replace the fuel filters to make sure they remain clean and free of debris.
• Ask your dealer about fuel additives that help prevent fungus or other buildup in your fuel tank.
Anti-siphon Valve
NOTICE
• If an engine running problem is diagnosed as fuel starvation, check the anti-siphon valve. If
the valve is stuck or clogged, change or replace it while the engine is shut down.
• NEVER run the engine with the anti-siphon valve removed, except in an emergency.
•
•
•
•
Your boat is equipped with an anti-siphon valve, which is an integral part of fuel system.
The valve is located at the point where the fuel feed line attaches to the fuel tank.
The valve is spring loaded and is opened by fuel pump vacuum.
This valve will prevent fuel from siphoning from the tank in the event of a fuel line rupture.
15
Chapter 3: Propulsion & Related Systems
2452 Classic Cruiser • Owner’s Manual Supplement
Quick Oil Drain System
QUICK OIL DRAIN SYSTEM
TRANSOM
OIL DRAIN HOSE
OIL DRAIN PLUG
ENGINE OIL PAN
GARBOARD
DRAIN PLUG
DRAW
CORD
BILGE
GARBOARD
DRAIN
To drain the engine oil:
1.
2.
3.
4.
5.
6.
7.
8.
Remove the boat from the water.
Unscrew the garboard drain plug.
Pull the draw cord until the oil drain plug and the oil drain hose slide out of the garboard drain.
Place the end of the oil drain hose into a suitable container.
Unscrew the oil drain plug and drain the engine oil.
Replace the oil drain plug.
Push the drain hose back into the bilge.
Replace the garboard drain plug.
Always dispose of waste oil in accordance with local regulations.
16
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 4: Controls
Steering
• This boat features a power assisted rack-and-pinion steering system.
• Check the fluid level in the power steering reservoir every time you use your boat.
• Boat steering is not self-centering.
Shift/Throttle
!
WARNING!
LOSS OF CONTROL HAZARD!
Improper maintenance of shift/throttle hardware may cause a sudden loss of control!
• Carefully read and understand all of the information about the shift/throttle in the
Cruiser & Yacht Owner’s Manual.
• Also, read and understand the shifter/throttle and engine manuals included in your owner’s packet.
Power Trim and Tilt
• The stern drive on your boat is equipped with power trim and tilt.
• Trim and tilt instructions are provided in the engine operation manual and the shifter/throttle manual is included in
your owner’s packet.
17
Chapter 4: Controls
2452 Classic Cruiser • Owner’s Manual Supplement
Trim Tabs (If Equipped)
!
WARNING!
LOSS OF CONTROL HAZARD!
Improper use of trim tabs will cause loss of control!
• Do not allow anyone unfamiliar with trim tabs to use them.
• Do not use trim tabs in a following sea as they will cause broaching or other unsafe handling
characteristics.
• Do not use trim tabs to compensate for excessive unequal weight distribution.
.
TYPICAL TRIM TAB
(TRANSOM VIEW)
VIEW OF DASH
TRIM TAB SWITCHES
TRANSOM
TRIM TAB
(TYPICAL)
• The trim tabs may be used to help keep your boat level at cruising speeds.
• The trim tabs are controlled by two rocker switches at the helm.
• Before using the trim tabs read and understand the trim tab operation manual included in your boat’s
owner’s packet.
Observe the following:
• Once cruising speed is reached, the port or starboard trim switch may be used (one at a time) to level the boat.
• Perform trim tab adjustment with several short touches to the switch rather than one long one.
• After each short touch allow several seconds for the hull to react.
• The trim tab hydraulic fluid reservoir is located in the engine compartment. The fluid level must be checked periodically (at least once a year) and refilled as necessary.
18
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 5: Navigation & Communication Equipment
Before using these systems for the first time, read and understand the instruction manuals and observe the following:
VHF Radio (If Equipped)
Your boat may include a VHF (Very High Frequency) radio at the helm. The VHF radio can be used to access
weather reports, summon assistance or contact other vessels as permitted by the FCC (Federal Communications
Commission). Be sure to contact the FCC for licensing, rules and regulations concerning VHF radio usage.
Compass (If Equipped)
NOTICE
Compass accuracy can be affected by many factors. Have a qualified technician calibrate your
compass. Make sure the technician gives you a deviation card which shows the corrections to
apply in navigational calculations. Keep a copy of the deviation card at the helm.
Your boat may come equipped with a compass. Carefully read and follow the manufacturer’s calibration and operating instructions provided in the boat’s owner’s packet.
19
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 6: Plumbing
Bilge Pumps
NOTICE
Discharge of oil, oil waste or fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities.
AFT BILGE
AFT BILGE PUMP
FORWARD BILGE
BILGE HOSE
THRU-HULL
FORWARD
FORWARD
BILGE PUMP
FORWARD
• Your boat is equipped with two automatic impeller-type bilge pumps which are used to pump water out
of the bilge.
• The bilge pumps are controlled by automatic bilge pump float switches (autofloat switches) and/or switches
at the helm.
• The bilge pumps are wired directly to the battery so they will normally function even when the boat is completely
shut down and left unattended.
20
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 6: Plumbing
Bilge Pump Testing
BILGE PUMP COMPONENTS
LIGHT FILM
OF OIL
“O” RING
OUTER
HOUSING
TAB
FIN
CAM
(TYPICAL)
POWER
SLOT
CARTRIDGE (TYPICAL)
• The bilge pumps are critical to the safety of your boat.
• Check the bilge pumps often to make sure they are working.
Test each pump often as follows:
1. Turn On the bilge pump switch at the helm.
2. Any water in the bilge should pump overboard.
• If the pump motor is running but not pumping inspect the discharge hose for a kink or collapsed area.
• If no problems are found, check the bilge pump housing for clogging debris as follows:
1. Remove the power cartridge:
a. Lift the tab while rotating the fins counter-clockwise.
b. Lift out the power cartridge.
c. Clear the outer housing of debris.
2. Reinstall the power cartridge:
a. Make sure the “O” ring is properly seated.
b. Coat the “O” ring with a light film of vegetable or mineral oil.
c. Align the cams on either side of the power cartridge with the two slots on the outer housing
d. Press the power cartridge into the housing while twisting clockwise.
3. Check the reinstallation by trying to twist the fins counter-clockwise without lifting the tab; the cartridge should
stay in place.
21
Chapter 6: Plumbing
2452 Classic Cruiser • Owner’s Manual Supplement
Autofloat Switches
• The automatic bilge pumps use electromagnetic float switches (autofloat) to turn On the pumps whenever water
rises above a preset level in the bilge.
• One autofloat switch is mounted next to each automatic bilge pump.
• The autofloat switches are wired directly to the battery and will normally function even when the boat is completely shut down and left unattended.
Test the autofloat switches often
as follows:
FLOAT SWITCH
TESTING
1. Push the float switch test button
up to turn On the bilge pump.
• If the pump does not turn On,
check the inline fuse.
• If the fuse is good but the switch
still doesn’t work, it may mean
the switch is bad or possibly the
battery is low.
2. Push test button all the way
down to return the float switch
to auto mode.
FLOAT SWITCH
TEST BUTTON
LIFT SWITCH UP
BILGE PUMP SHOULD TURN ON
!
PUSH SWITCH DOWN
BILGE PUMP SHOULD TURN OFF
CAUTION!
When the test is completed on each float switch, you MUST push the test button all the way
down to the auto position to return the switch to auto mode!
22
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 6: Plumbing
Seawater Systems
Seacocks
!
CAUTION!
SYSTEM DAMAGE HAZARD!
• Before using a seawater intake system, make sure that the system’s seacock is in the OPEN
position before the system is started and keep the seacock Open until the system is shut Off.
• Close the seacocks whenever the systems will not be used for long periods of time.
A seacock is a valve, controlled by a 90º lever, used to manage
the intake of seawater through the hull and below the water
line. Seacocks are typically used on your boat in the following
seawater intake systems:
• Marine head (toilet)
• Air conditioning system (if equipped)
Before using any of these systems, make sure that the system’s
seacock is Open and remains Open until the system is shut Off.
SEAWATER INTAKE VALVE (SEACOCK)
COMPONENTS (TYPICAL)
90 DEGREE
SEACOCK
LEVER
HULL
SECTION
SEACOCK (TYPICAL)
SEACOCK GASKET
INTAKE STRAINER
Seawater Strainers
• Seawater strainers are used in water pickup systems to filter incoming seawater.
• A seawater strainer is located near each system’s seacock.
• Check the strainers for leaks and/or debris every time you use your boat.
• If debris is found, clean the seawater strainer as follows:
!
CAUTION!
FLOODING HAZARD!
• The seacock that sends seawater to the strainer must be CLOSED before disassembling
the seawater strainer to prevent the boat from taking on water through the seawater
strainer assembly.
• Keep the seacock CLOSED until the seawater strainer is completely reassembled.
SYSTEM DAMAGE HAZARD!
• After reassembling the seawater strainer, make sure that the seacock valve is OPEN before
using the component/system.
1. Turn Off the component or system (marine head, air conditioning system, etc.) that the strainer is connected to.
2. Close the seacock that sends seawater to the strainer you are about to clean. The seacock must remain Closed
until the strainer is completely reassembled.
3. Take apart the seawater strainer.
4. Remove the debris.
5. Flush the strainer with water.
6. Reassemble the seawater strainer.
7. Open the seacock and check for leaks around the strainer.
8. If no leaks are found, you may use the component or system.
23
Chapter 6: Plumbing
2452 Classic Cruiser • Owner’s Manual Supplement
Freshwater System
!
WARNING!
• Only use safe drinking (potable) water in your boat’s freshwater system.
• Only use a sanitary drinking water hose to fill the water tank or connect to city water.
• Never use a common garden hose for drinking water.
FRESHWATER SYSTEM ROUTING
WATER HEATER
(IF EQUIPPED)
WATER TANK
WATER PUMP
WATER TANK
VENT HOSE
WATER TANK
FILL HOSE
PUMP
SWITCH
•
•
•
•
•
24
Read the Freshwater System section in the Cruiser & Yacht Owner’s Manual.
Your boat is equipped with a pressure type (demand) freshwater (potable) system.
This system can be pressurized by turning On the water pump.
See the Component Location section of this Supplement for the location of the water pump switch.
Since the water pump requires DC power, the battery switch must be in the "1", "2" or "BOTH" position for the
pump to work.
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 6: Plumbing
Observe the following about the freshwater system:
• Turn Off the water pump when the boat is not in use or the water tank is empty.
• Inspect and clean the water filter often (located on the water pump).
• When your boat is to be left unattended for long periods of time, pump the water tank dry to prevent stored water
from becoming stagnant and distasteful.
• If the freshwater system needs to be disinfected, ask your dealer about treatments available for your boat’s system.
Freshwater System Winterization
!
CAUTION!
WATER SYSTEM DAMAGE HAZARD!
Never blow compressed air through the water system when all of the faucets are Closed.
1. Turn On the water system switch.
2. Open all of the faucets and showers and let the water system drain completely.
3. Turn Off the water system switch.
Any remaining water must be removed from the water lines. There are two ways to remove the remaining water from
the lines:
• Compressed Air
• Gravity Draining
Compressed Air
You must have an air compressor with an air hose
and an air nozzle.
1. Remove the water line from the outlet side of
the water pump (opposite side from filter).
2. Open the faucet that is furthest away from the
water pump.
3. Place the air nozzle against the end of the just
removed water line and blow air through
the system.
4. When water stops coming out of the Open faucet, stop the air and Close the faucet.
5. One at a time, repeat this process on all faucets
and showers.
NOTE: LOCATION OF
TEE FITTING & DRAIN
PLUG MAY VARY
TYPICAL VIEW
DRAIN PLUG
INLET SIDE
WATER LINE
FILTER
WATER PUMP
Gravity Draining
1. Open all faucets and showers.
2. Remove the drain plug from the tee fitting on
the freshwater tank.
3. When the water has stopped draining from the
freshwater tank, replace the drain plug.
OUTLET SIDE
WATER LINE
FRESHWATER TANK
TEE FITTING
Transom Shower (If Equipped)
• The water pump switch must be turned On before using the transom shower.
• Be sure to read the manufacturer’s instructions, provided in your owner’s packet.
25
Chapter 6: Plumbing
2452 Classic Cruiser • Owner’s Manual Supplement
Water Heater
!
WARNING!
HOT HAZARD!
Water heated by the water heater can reach temperatures hot enough to scald the skin.
!
CAUTION!
WATER HEATER DAMAGE HAZARD!
• DO NOT turn on the water heater electrical circuit on the AC panel until the water heater
tank is COMPLETELY filled with water.
• Even momentary operation in a dry tank will damage the heating elements.
• Warranty replacements WILL NOT be made on elements damaged in this manner.
• The tank is full if water flows from the tap when the hot water is turned On in the galley.
• The water heater should be drained and the power turned OFF when the possibility of
freezing exists.
NOTICE
If your boat is connected to shore power but the water heater is not working:
• Make sure the water heater circuit breaker on the AC panel is switched On.
If the circuit breaker on the AC panel is On, but the water heater is still not working:
• Consult with your dealer about checking the "push to reset" circuit breaker located on the
water heater.
• The water heater is connected to the AC power system, therefore, you must make sure that the water heater
breaker on the AC panel is turned On before water will be heated.
• Read the manufacturer’s instruction manual supplied in your boat’s owner’s packet and observe the
warnings above.
Winterizing the Water Heater
1. Turn Off the water heater breaker.
2. Disconnect the hose (A) attached to the pressure relief valve (B).
3. If there is any water in this hose, drain it into
the bilge or into a bucket.
4. Open the pressure relief valve (B).
5. Open the drain valve (C).
• Leave the pressure relief and drain valves
Open until you fit out the boat after storage.
26
B
A
C
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 6: Plumbing
Drain Systems
Sink Drains
Gray water (water from the sinks) is gravity drained overboard.
Deck Drains
NOTE: VIEW IS UNDERSIDE OF AFT DECK
STORAGE
DRAIN
DECK
DRAINS
STORAGE
DRAIN
DECK
DRAINS
STORAGE
DRAIN
HATCH
DRAIN
Water on the deck is drained overboard through the deck drains. Keep the deck drains free of debris.
27
Chapter 6: Plumbing
2452 Classic Cruiser • Owner’s Manual Supplement
Portable Toilet (If Equipped)
Read the manufacturer’s operating instructions supplied in your owner’s packet before using the portable toilet.
Marine Head with Holding Tank (If Equipped)
NOTICE
Check with local authorities for regulations regarding the legal use of marine head systems.
• Read the marine head operation and maintenance manual (included in your boat’s
owner’s packet).
• The holding tank is plumbed
to a waste fitting on the deck
for dockside pump-out.
• Check the content level of
the holding tank by looking
at the side of the tank.
• Empty the holding
tank often.
HOLDING TANK
WATER TANK
WASTE PUMP-OUT
DECK FITTING
HOLDING
TANK VENT
MARINE
HEAD TO
HOLDING
TANK
WASTE PUMPOUT HOSE
HOLDING TANK
VENT HOSE
Using the marine head:
1.
2.
3.
4.
Open the head’s seawater intake valve (seacock).
Before using the head, pump enough water into the bowl to wet the sides.
After use, pump until the bowl is thoroughly cleaned. Continue pumping a few more times to clean the lines.
If excess waste causes the water to rise in the bowl, stop pumping until the water recedes.
Winterizing The Marine Head
1.
2.
•
•
28
Shut Off the intake seacock, and pump the head until the bowl is dry.
Remove the drain plug in the base and pump again to remove all of the water.
Do not fill the bowl with anti-freeze.
Close the intake seacock while the boat is underway or whenever the boat is left moored in the water.
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 6: Plumbing
Macerator (If Equipped)
NOTICE
Check with local authorities for regulations regarding the legal use of marine head systems.
To use the macerator to pump
waste directly into the water
(where regulations permit):
1. Open the underwater discharge seacock.
2. Press both macerator
switches at the same time to
run the pump. Do not continue running the macerator
if the waste holding tank
is empty.
3. Close the underwater discharge seacock when you are
done pumping.
HOLDING
TANK
HOLDING TANK
VENT HOSE
WATER
TANK
WASTE PUMP-OUT
DECK FITTING
HOLDING
TANK VENT
MACERATOR
PUMP
OVERBOARD DISCHARGE VALVE
WASTE PUMPOUT HOSE
29
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 7: Deck Equipment
Cleats and Tow Eyes
!
WARNING!
PERSONAL INJURY and /or PRODUCT or PROPERTY DAMAGE HAZARD!
• NEVER lift the boat using the bow and stern eyes or the cleats.
Carefully read the section on towing in the Cruiser & Yacht Owner’s Manual before:
• Towing anything behind the boat.
• Being towed by another vessel.
30
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 8: Appliances & Entertainment Systems
NOTICE
Always keep an approved ABC-type fire extinguisher in galley area.
All appliances installed on your boat come with their own manuals. These manuals contain detailed instructions and
important safeguards. Thoroughly read and understand these manuals before using your boat’s appliances.
• Make sure the AC breaker is turned On for the appliance you wish to use.
Refrigerator (If Equipped)
Your boat features a dual voltage, 120-volt AC/12-volt DC, refrigerator. The refrigerator runs on 12-volt DC power
unless 120-volt AC power is being supplied by shore power and the AC refrigerator breaker is On.
Microwave Oven (If Equipped)
Before attempting to use the microwave oven, make sure the breaker switch on the AC master panel is On.
Electric Stove (If Equipped)
!
•
•
•
•
•
•
WARNING!
BURN/SCALDING and/or FIRE HAZARD!
Read the stove’s instruction manual before using.
Always keep an approved ABC-type fire extinguisher in galley area.
Do not use the stove while underway.
Any non-cooking devices on or near your stove during use are potential fire hazards!
DO NOT touch burners, grates or nearby surfaces as they may be hot even when they are
dark in color. Areas near burners and grates may become hot enough to cause burns.
During and after use, do not touch or let clothing or other flammable material come in contact with heated units or areas near the units (burner tops, main frame sides and back, sea
rails and pot holders) until they have had sufficient time to cool.
31
Chapter 8: Appliances & Entertainment Systems
2452 Classic Cruiser • Owner’s Manual Supplement
Alcohol/Electric Stove (If Equipped)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
• The alcohol stove is a source of dangerous carbon monoxide gas (CO).
• BEFORE using the alcohol stove, Open doors and windows to make sure
there is enough fresh air for ventilation.
!
WARNING!
• Open flame cooking appliances consume oxygen, this can cause asphyxiation or death.
• Maintain open ventilation.
!
•
•
•
•
•
•
WARNING!
BURN/SCALDING and/or FIRE HAZARD!
Read the stove’s instruction manual before using.
Always keep an approved ABC-type fire extinguisher in galley area.
Do not use the stove while underway.
Any non-cooking devices on or near your stove during use are potential fire hazards!
DO NOT touch burners, grates or nearby surfaces as they may be hot even when they are
dark in color. Areas near burners and grates may become hot enough to cause burns.
During and after use, do not touch or let clothing or other flammable material come in contact with heated units or areas near the units (burner tops, main frame sides and back, sea
rails and pot holders) until they have had sufficient time to cool.
!
CAUTION!
PRODUCT DAMAGE HAZARD!
To prevent overheating which can destroy the electric burner elements, NEVER attempt to use
both alcohol and electric burners simultaneously.
Audio & Visual Equipment
NOTICE
AM radio reception may be impaired anytime the engine is running.
32
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 9: Convertible Seats, Beds, & Tables
Dinette/Berth
A
B
C
D
The dinette table can be removed and the dinette area can be converted into a berth.
1. Lift the table (A) and remove the table leg (B).
2. Place the table so that it fits securely on the support brackets (C) at the front of the dinette seats.
3. Place the filler cushion (D) on top of the table.
33
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 10: Lights
Care and Maintenance
All of the lights installed on your boat are of top quality, but you should be aware that failure may periodically occur
for a variety of reasons:
1.
2.
3.
4.
There may be a blown fuse - replace the fuse.
The bulb may be burned out - carry spare bulbs for replacement.
A wire may be damaged or may have come loose - repair as required.
The bulb base may be corroded - clean the base and coat it with non-conductive electrical lubricant.
Navigation Lights
!
CAUTION!
Avoid the storage of gear where it would block navigation lights from view.
Read and understand the navigation light section of Cruiser & Yacht Owner’s Manual.
Interior & Exterior Lights
!
CAUTION!
• Be conservative in the use of battery power.
• Prolonged use of cabin interior lights (overnight) will result in a drained battery.
•
•
•
•
34
The lights are powered by the boat’s 12-volt DC system.
The battery switch must be in the 1, 2 or BOTH position for the lights to work.
There are On/Off light switches for different sets of lights on the cabin wall.
Some individual lights also have a switch on the light.
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 11: Air Conditioning (If Equipped)
Air Conditioning System (If Equipped)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD!
Dangerous carbon monoxide gas (CO) can be brought into the boat through
the air conditioning system.
!
CAUTION!
SYSTEM DAMAGE HAZARD!
The air conditioning system’s seacock must be OPENED before turning on the air conditioner
and must remain OPEN during use.
AIR CONDITIONER SYSTEM ROUTING
PICKUP PUMP
AIR CONDITIONER
DRAIN HOSES
SEA
STRAINER
SEAWATER PICKUP
& BALL VALVE
AIR CONDITIONER
AIR RETURN VENT
GALLEY VENT
VENT HOSE
(TYPICAL)
Read the air conditioner manual, included in your owner’s packet, before using the air conditioning system.
• Before using the air conditioning system, make sure the breakers on the AC main distribution panel are turned On
and make sure the system’s seawater pickup seacock is Open. The seacock must remain Open anytime the air
conditioner is in use.
• Check the seawater pickup strainer for debris according to the directions given in the Seawater Strainer section of
this Supplement.
35
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
!
•
•
•
•
•
EXTREME FIRE, SHOCK & EXPLOSION HAZARD!
To minimize the risks of fire and explosion, NEVER install knife switches or other arcing
devices in the fuel compartments.
NEVER substitute automotive parts for marine parts. Electrical, ignition and fuel system
parts were designed and manufactured to comply with rules and regulations that minimize
risks of fire and explosion.
DO NOT modify the electrical systems or relevant drawings.
Have qualified personnel install batteries and/or perform electrical system maintenance.
Turn OFF the battery switch BEFORE doing any work in the engine spaces.
!
•
•
•
•
DANGER!
WARNING!
FIRE & EXPLOSION HAZARD!
Fuel fumes are heavier than air and will collect in the bilge areas where they can be
accidently ignited.
Visually and by smell (sniff test), check the engine and fuel compartments for fumes or
accumulation of fuel.
ALWAYS run the bilge blowers for at least four minutes before turning on electrical devices,
starting the engine, or electrical system maintenance.
Minimize the danger of fire and explosion by not exposing the batteries to open flame or
sparks. NEVER smoke anywhere near the batteries.
!
CAUTION!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER disconnect the battery cables while the engine is running since it can cause
damage to your boat’s electrical system components.
NOTICE
Electrical connections are prone to corrosion. To reduce corrosion caused electrical problems,
keep all electrical connections clean and apply a spray-on protectant that is designed to protect
connections from corrosion.
36
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
12-Volt DC System
Batteries
The batteries supply electricity for lights, accessories, and engine starting.
The Electrical section of Chapter 8, in the Cruiser & Yacht Owner’s Manual, provides battery care and
maintenance instructions.
Fuses and Circuit Breakers
• Fuses and circuit breakers for engines and main accessory power are on the DC main distribution panel and on the
battery switch panel.
• Some equipment may have secondary fuse protection at the unit, behind the battery switch panel or at
the batteries.
• Electronics power is provided at the helm station.
Battery Switch
• The battery switch has four (4) positions.
• Some "Standby Loads", such as the CO monitor, the
automatic bilge pumps, and the stereo memory, are not
affected by the battery switch since they are wired
directly to the battery (see the Wiring Diagrams in this
Supplement for more details).
POSITION "1"
ACTIVATES
BATTERY "1"
POSITION "BOTH"
ACTIVATES BOTH
BATTERIES
POSITION "2"
ACTIVATES
BATTERY "2"
"OFF"
POSITION
BATTERY SWITCH
Battery Switch Positions
NOTICE
Since the batteries on your boat were dealer-installed, the battery switch positions listed below
may vary. Make sure you get a full explanation of battery switch use from your selling dealer.
Battery Switch
Position
Engine Starting
Accessories and Lights
Engine Alternator
Battery Charger
POSITION
1
Battery 1
Provides
Starting Power
Battery 1
Provides Power for
Accessories and Lights
Charges
Battery 1
Charges
BOTH
Batteries
POSITION
2
Battery 2
Provides
Starting Power
Battery 2
Provides Power for
Accessories and Lights
Charges
Battery 2
Charges
BOTH
Batteries
Charges BOTH
Batteries
Batteries will NOT
Charge Properly
POSITION
BOTH
BOTH Batteries
BOTH Batteries Provide
Provide Starting Power for Accessories and
Power
Lights (not advised
unless engine is running)
37
Chapter 12: Electrical System
2452 Classic Cruiser • Owner’s Manual Supplement
Alternator
The engine alternator will keep the batteries properly charged when running at cruising speeds.
Battery Charger (If Equipped)
!
CAUTION!
ENGINE & ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER run the boat’s engine and the battery charger at the same time.
!
CAUTION!
The battery charging systems (alternator and battery charger) installed on your boat are
designed to charge conventional lead-acid batteries. Before installing gel-cell or other new technology batteries, consult with the battery manufacturer about charging system requirements.
Thoroughly read and understand the battery charger manual (provided in your owner’s packet) before using the battery charger for the first time.
• The battery charger will charge the boat’s batteries whenever the boat is plugged into 120V/60Hz shore power and
the "BATTERY CHARGER" AC breaker is On.
• The battery switch can be in any position during charging.
• You may use DC powered electrical systems, such as the lights and stereo when the battery charger is On, but
there will be a corresponding drop in charger performance.
12-Volt Accessory Outlet
!
CAUTION!
DO NOT use the 12-volt accessory outlet with a cigarette or cigar lighter. High temperatures
may melt the outlet.
• Your boat is equipped with a 12-volt accessory outlet at the helm.
• The outlet can be used with any 12-volt device which draws 15 amps or less.
• The 12-volt accessory outlet is protected by a 15 amp circuit breaker on the main circuit breaker panel.
38
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
120-Volt AC System (If Equipped)
!
CAUTION!
WATER HEATER DAMAGE HAZARD!
• DO NOT turn on the water heater AC panel electrical circuit until the water heater tank is
COMPLETELY filled with water.
• The tank is full if water flows from the tap when the hot water is turned On in the galley.
• Even momentary operation in a dry tank will damage the heating elements.
• Warranty replacements WILL NOT be made on elements damaged in this manner.
SINGLE SHORE POWER AC PANEL
NOTICE
When using shore power the simultaneous use of several AC components can result in an
overloaded circuit. It may be necessary to turn Off one or more accessories in order to
use another accessory.
• Τhe 120V/60Hz AC system can be energized by shore power.
• The master circuit breakers, located on the AC panel, provide power source selections to AC powered accessories.
Individual breakers must be turned On to supply power to the accessories you wish to use.
• The AC panel may contain inactive circuit breakers for accessories that are not available for this model boat.
39
Chapter 12: Electrical System
2452 Classic Cruiser • Owner’s Manual Supplement
Shore Power
!
•
•
•
•
•
DANGER!
FIRE, EXPLOSION & SHOCK HAZARD!
DO NOT alter shore power connectors and use only compatible connectors.
Before plugging in or unplugging the shore power cord to your boat, make sure all breakers
and switches on the AC master panel are turned OFF.
To prevent shock or injury from an accidental dropping of the “hot” cord into the water,
ALWAYS plug the shore power cord to the boat inlet first; then to the dockside outlet. When
unplugging from shore power, unplug the shore power cord from the dockside outlet first.
NEVER leave a shore power cord plugged in to the dockside outlet only.
Only use shore power cords approved for marine use. NEVER use ordinary indoor or outdoor extension cords that are not rated for marine use.
!
WARNING!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
• Monitor the polarity indicator lights EVERY TIME you connect to shore power.
• If a red reversed polarity light turns On when you are connecting to shore power, DO NOT
turn on the main breaker switches.
• Instead, IMMEDIATELY unplug the shore power cord (ALWAYS from the dockside outlet
first) and alert marina management.
!
•
•
•
•
40
WARNING!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
Periodically check the shore power cord(s) for deterioration or damage.
NEVER use damaged or faulty cords since the danger of fire and electrical shock exists.
DO NOT pinch shore power cords in doors or hatches, or coil the shore power cord too
tightly since these situations can generate enough heat to result in a fire.
If a shore power cord accidently becomes immersed in water, THOROUGHLY dry the
blades and contact slots before reusing.
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
!
CAUTION!
ELECTRICAL SYSTEM DAMAGE HAZARD!
• NEVER connect to dockside power outside of North America unless you have purchased the
international electrical conversion option.
• Using several AC components at the same time can result in an overloaded circuit. You may
have to turn Off one or more components in order to use another accessory.
• Use double insulated or three-wire protected electrical appliances whenever possible.
NOTICE
• Some dockside installations may be rated less than 30 amps, therefore, you may need to purchase lower amp adapters.
• Whenever a lower amp adapter is used, however, there will be a corresponding drop in supplied power from the dockside system.
• The single shore power 120V/60Hz, AC system (if equipped) features one, 120V/30 amp, shore power receptacle.
• If your boat is equipped with an air conditioning system, a second (dual) 30 amp inlet has been installed.
• The dual shore power inlets are labeled "LINE 1" and "LINE 2", which corresponds to the "LINE 1" and "LINE 2"
master breakers on the AC panel.
• The dual shore power system is designed so that each line is independent of the other except when the AC power
transfer switch is used.
41
Chapter 12: Electrical System
2452 Classic Cruiser • Owner’s Manual Supplement
Connecting To Shore Power
NOTES:
DUEL INLETS ONLY IF
EQUIPPED WITH AIR CONDITIONER
TYPICAL SHORE
POWER INLET
SHORE POWER
INLET(S)
DUAL SHORE POWER AC PANEL (IF EQUIPPED)
LINE 1
DOCKSIDE MASTER
VOLTMETER
SELECTOR SWITCH
VOLTMETER
LINE 1
POLARITY
LIGHT
LINE 2
TRANSFER
LINE 2
DOCKSIDE MASTER
LINE 2
POLARITY
LIGHT
10 AMPS
15 AMPS
20 AMPS
15 AMPS
5 AMPS
15 AMPS
25 AMPS
15 AMPS
FIGURE 1
42
2452 Classic Cruiser • Owner’s Manual Supplement
1.
2.
3.
4.
•
•
5.
6.
7.
Chapter 12: Electrical System
Review all hazard information at the beginning of this section, Shore Power.
Turn Off all breakers and switches on the AC master panel.
Attach the shore power cord to the boat inlet first then to the dockside outlet.
Monitor the AC panel’s polarity indicator lights, located below the line master breaker(s), as follows:
A green light illuminating after the power cord is plugged into the dockside outlet indicates acceptable electrical power. You may turn On the master breaker switch.
A red light, however, indicates reversed polarity, which could cause electrical system damage and possibly
electrical shock injuries. In this case, do not turn On the master breaker switch.
Switch the "LINE 1 DOCKSIDE MASTER" On.
If equipped with dual dockside, switch the "LINE 2 DOCKSIDE MASTER" On.
Turn On the individual component breakers as required.
Transfer Switch (If Equipped with Dual Shore Power)
NOTICE
• When using the "Transfer Switch" do not exceed 30 total amps.
• The amperage of each component breaker is shown in figure 1.
• The voltage on each line can be read by setting the voltmeter selector switch.
When only one dockside outlet is available, you can use the "Transfer Switch" to provide power to both lines.
1. Connect to shore power as described in steps 1 through 4 above.
2. Switch the "LINE 1 TRANSFER SWITCH" (transfers power from line 1 to line 2) On instead of the
"LINE 2 DOCKSIDE MASTER.
3. Turn On the individual component breakers as required.
43
Chapter 12: Electrical System
2452 Classic Cruiser • Owner’s Manual Supplement
Electrical Routings
Hull Electrical Harness
BILGE PUMP
SENDING
UNIT
TO BATTERY
SWITCH
TO GALLEY
REFRIGERATOR
TRIM TAB
PUMP
GROUNDING BLOCK/
ENGINE GROUND
PLASTIC LABEL BRANDED INTO THE FACE
ABCDEFG
THRU PVC TUBE
ENGINE
PLUG
TRIM TILT
PUMP
TO DASH
FIRE BOY
MACERATOR
WATER PUMP
FWD BILGE
Deck Electrical Harness.
CO MONITOR
COMPASS
DINETTE
LIGHTS
WIPER
MOTOR
SPEAKER
HORN
LIGHT
SPEAKER
NOTE: VIEW IS UNDERSIDE OF DECK
44
HEAD
LIGHT
GALLEY
LIGHTS
LIGHT
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
120 Volt AC System (If Equipped)
TO GALLEY
TO WATER
HEATER
TO BATTERY
CHARGER
THRU PVC TUBE
REFRIGERATOR
THRU PVC
TUBE
RECEPTACLE BOX
AIR CONDITIONER PUMP
AIR CONDITIONER
Battery System
STARTER
TO BATTERY
SWITCH
ENGINE
TRIM PUMP
BATTERY CHARGER
(IF EQUIPPED)
45
Chapter 12: Electrical System
2452 Classic Cruiser • Owner’s Manual Supplement
Bonding Harness
FUEL TANK
AIR CONDITIONER
PICKUP
AIR CONDITIONER THRU PVC PIPE
STRAINER
AIR CONDITIONER
PANEL
BONDING BLOCK
GROUND
PLASTIC LABEL BRANDED INTO THE FACE
ABCDEFG
FUEL FILL
MACERATOR DISCHARGE
THRU HULL
46
AIR CONDITIONER
PUMP
HEAD PICKUP
AIR CONDITIONER
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
Wire Diagrams
Engine Electrical System
47
Chapter 12: Electrical System
Single Dockside
48
2452 Classic Cruiser • Owner’s Manual Supplement
2452 Classic Cruiser • Owner’s Manual Supplement
Chapter 12: Electrical System
Dual Dockside
49
2452 Classic Cruiser • Owner’s Manual Supplement
Important Records
Selling Dealer
Key Numbers
Name Of Dealership
Ignition
Other
Address
Electronics
Phone/FAX/E-mail
Manufacturer
Model Name/Number
Sales Manager
Serial Number
Service Manager
Manufacturer
Model Name/Number
Engine
Serial Number
Manufacturer
Model Name/Number
Engine Serial Number
Oil Type/SAE
Quarts per Engine
Manufacturer
Filter Type
Propeller
Model Name/Number
Serial Number
Manufacturer
Model Name/Number
Serial Number
Manufacturer
Pitch
Model Number
50
2452 Classic Cruiser • Owner’s Manual Supplement
Float Plan
Before going boating, fill out a copy of this float plan (or similar) and leave it with a reliable person whom you can
depend on to contact the Coast Guard or other rescue organization, if you do not return as scheduled.
Description of Boat
Persons on Board
Registration/Documentation Number
Length
Make
Hull Color
Full Name
Type
Age
Health
Phone Number
Trim Color
Full Name
Fuel Capacity
Engine Type
Number of Engines
Age
Health
Phone Number
Distinguishing Features
Full Name
Distinguishing Features
Age
Health
Phone Number
Operator of Boat
Full Name
Full Name
Age
Male or Female
Age
Health
Phone Number
Health
Full Name
Address
Age
Health
Phone Number
Address
Full Name
Phone/FAX/E-mail
Operator’s Experience
Age
Health
Phone Number
Full Name
Age
Health
Phone Number
Full Name
Age
Health
Phone Number
51
Float Plan
2452 Classic Cruiser • Owner’s Manual Supplement
Survival Equipment
Trip Expectations
Marine Radio (Yes/No)
Type
Frequencies
Number of PFDs
Flares (Yes/No)
Mirror (yes or no)
Flashlight (Yes/No)
Food (Yes/No)
Smoke Signals (Yes/No)
Departing From
Departure Date
Departure Time
Stopover 1
Water (Yes/No)
Anchor (Yes/No)
Raft/Dinghy (Yes/No)
Arrive No Later Than: Date
Paddles (Yes/No)
EPIRB (Yes/No)
Other
Other
Other
Other
Arrive No Later Than: Time
Stopover 2
Arrive No Later Than: Date
Arrive No Later Than: Time
Vehicle Description
Stopover 3
Make
Model
Arrive No Later Than: Date
Color
Arrive No Later Than: Time
License Number
Stopover 4
Where is the Vehicle Parked?
Arrive No Later Than: Date
Arrive No Later Than: Time
Stopover 5
Arrive No Later Than: Date
Arrive No Later Than: Time
Stopover 6
Arrive No Later Than: Date
Arrive No Later Than: Time
Final Destination Port (If Different Than Home Port)
Arrive No Later Than: Date
Arrive No Later Than: Time
If not returned by the date and time listed above, call
the Coast Guard or other local authority.
Coast Guard Phone Number
Local Authority Phone Number
52
Owner’s Notes
Owner’s Notes
Owner’s Notes
Owner’s Notes
Part Number 1718021
Bayliner • P.O. Box 9029 • Everett, WA 98206 • 360-435-5571
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising