Dangerous | COMPRESSOR | Operator`s manual | Dangerous COMPRESSOR Operator`s manual

Dangerous COMPRESSOR Operator`s manual
®
OPERATOR’S MANUAL
5-Gallon Pancake
Air Compressor
Item #2275
09/10
IMPORTANT:
Your new WEN® tool and/or equipment has been engineered and manufactured to high standards
for dependability, ease of operation, and operator safety. Properly cared for, it will give you years
of rugged, trouble-free performance.
ay close attention to the Rules for Safe Operation and Warnings. If you use your tool and/or P
equipment properly and only for what it is intended, you will enjoy years of safe, reliable service.
It's not how, it's WEN the project get's done!
Contact us for product questions or technical support.
WenProducts.com
800-232-1195 M–F 8–5 (CST)
techsupport@wenproducts.com
AIR COMPRESSOR IDENTIFICATION
For information and questions please contact customer service at 1-800-232-1195. Please fill out the information below and have it accessible prior to calling. For the Serial Number refer to the
specifications sticker on your Air Compressor.
DATE OF PURCHASE: _____________________________________________________________
PURCHASED FROM:
_____________________________________________________________
ITEM #:
_____________________________________________________________
SERIAL NUMBER:
_____________________________________________________________
®
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Air Compressor Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
Electrical Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–9
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SPECIFICATIONS
5-Gallon Pancake Air Compressor
Item #:
Motor: Pressure Range:
Air Flow: Air Outlet Size:
Tank Capacity:
Weight: 2275
120V, 60Hz, 13 Amps
85–125 psi
4.2 CFM @ 40 psi
3.2 CFM @ 90 psi
1/4" NPT
5-Gallons
48 lbs.
#2275 OPERATOR’S MANUAL
3
®
IMPORTANT SAFETY INSTRUCTIONS
1. The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols,
and the explanations with them, deserve your careful attention and understanding. The safety
warnings do not by themselves eliminate any danger. The instructions or warnings they give are not
substitutes for proper accident prevention measures.
WARNING: This is a safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety rules that follow this symbol to avoid possible injury or death.
Note: Advises you of information or instructions vital to the operation or maintenance of the equipment.
2. Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the tool/equipment to WEN PRODUCTS for
repair. When servicing, use only identical WEN replacement parts.
3. READ ALL INSTRUCTIONS BEFORE USING YOUR AIR COMPRESSOR.
4. Failure to follow all instructions listed below may result in electrical shock, fire and/or serious personal injury.
ARNING: Do not attempt to operate this tool/equipment until you have read thoroughly
W
and understand completely all instructions, safety rules, contained in this manual. Failure to
comply can result in accidents involving fire, electric shock, or serious personal injury. Save
this operator’s manual and review frequently for continuing safe operation and instructing
others who may use this tool/equipment.
5. Safe operation of this tool/equipment requires that you read and understand this operator’s manual
and all labels affixed to the tool/equipment. Safety is a combination of common sense, staying alert
and knowing how your tool/equipment works.
GENERAL SAFETY INSTRUCTIONS
WARNING: Read all safety warnings and instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
#2275 OPERATOR’S MANUAL
4
®
Work Area Safety
1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
2. Do not operate your Air Compressor in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Air Compressor motors produce sparks which may ignite the dust or
fumes.
3. Keep children and bystanders away from an operating Air Compressor.
Electrical Safety
1.
ir Compressor plugs must match the outlet. Never modify the plug in any way. Do not use any
A
adapter plugs with grounded Air Compressors. Standard plugs and matching outlets will reduce
the risk of electric shock.
2.
o not expose your Air Compressor to rain or wet conditions. Water entering your Air CompresD
sor will increase the risk of electric shock.
3.
o not abuse the cord. Never use the cord for unplugging your Air Compressor. Keep the cord
D
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
Personal Safety
1.
tay alert, watch what you are doing and use common sense when operating your Air CompresS
sor. Do not use your Air Compressor while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattentiveness while operating your Air Compressor may result in
serious personal injury.
2.
se protective safety equipment. Always wear ANSI-approved eye protection during setup and
U
use.
3.
revent unintentional starting. Ensure the switch is in the OFF position before connecting to
P
power source or moving your Air Compressor.
Air Compressor Use and Care
1. D
o not use your Air Compressor if the switch does not turn ON and OFF. An Air Compressor that
cannot be controlled with the switch is dangerous and must be repaired.
2. Disconnect the plug from the power source before making any adjustments, changing accessories,
or storing your Air Compressor. This preventive safety measures reduce the risk of starting your Air
Compressor accidentally.
#2275 OPERATOR’S MANUAL
5
®
3. Store your Air Compressor out of the reach of children and do not allow people unfamiliar with your
Air Compressor or these instructions to operate it. An Air Compressor is dangerous in the hands of
untrained users.
4. Maintain your Air Compressor. Keep your Air Compressor clean for maximum performance. Follow the instructions for lubricating and changing accessories. Keep your Air Compressor dry, clean
and free from oil and grease. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect your Air Compressor's operation. If damaged, have your Air
Compressor repaired professionally before use. Many accidents are caused by a poorly maintained
Air Compressor.
5. Use your Air Compressor in accordance with these instructions, taking into account the working
conditions and the work to be performed. Use of your Air Compressor for operations different from
those intended could result in a hazardous situation.
Service
Have your Air Compressor serviced by a qualified professional repair person using only identical replacement parts. This will ensure that the safety of your Air Compressor is maintained.
AIR COMPRESSOR SAFETY INFORMATION
1. RISK OF FIRE OR EXPLOSION – Do not spray flammable liquid in a confined area or towards a
hot surface. The spray area must be well-ventilated. Do not smoke while spraying or spray where
spark or flame is present.
2. ARCING PARTS – Keep your Air Compressor at least 20 feet away from explosive vapors, such as
when spraying with a spray gun.
3. RISK OF BURSTING – Do not adjust regulator higher than marked maximum pressure of attached
pneumatic tool/equipment.
4. RISK OF INJURY – Do not direct air stream at people or animals.
5. Do not use to supply breathing air.
6. Do not leave your Air Compressor unattended for an extended period while plugged in. Unplug
compressor after use.
7. Keep your Air Compressor well-ventilated and do not cover during use.
8. Drain tank daily or after use. Internal rust causes tank failure and explosion.
9. Your Air Compressor's cylinder head and air lines get hot during operation. Do not touch or allow
children nearby during or immediately following operation.
10.Do not use the air hose to move your Air Compressor.
#2275 OPERATOR’S MANUAL
6
®
11.Release the pressure in the storage tank before moving.
12.The use of accessories or attachments not recommended by the manufacturer may result in bodily
injury.
13.All air line components, including hoses, pipe, connectors, and filters must be rated for a minimum
working pressure of 150% of the maximum system pressure.
14.Industrial applications must follow OSHA guidelines.
15.This product is not a toy. Keep it out of reach from children.
16.People with pacemakers should consult their physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
WARNING: The brass components of this product contain lead, a chemical known to the
State of California to cause birth defects (or other reproductive harm). (California Health &
Safety code 25249.5, et seq.)
17.The warnings, precautions, and instructions discussed in this Operator's Manual cannot cover all
the possible conditions and situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be supplied
by the operator.
ELECTRICAL INSTRUCTIONS
Grounding Instructions
1. IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool/equipment is equipped
with an electric cord that has an equipment grounding conductor and a grounding plug. The plug
MUST be plugged into a matching outlet that is properly installed and grounded in accordance with
ALL local codes and ordinances.
2. DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the outlet, have the proper outlet installed
by an electrician.
3. IMPROPER CONNECTION of the equipment grounding conductor can result in electric shock.
The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connect
the equipment grounding conductor to a live terminal. CHECK with a licensed electrician or service
personnel if you do not completely understand the grounding instructions, or if you are not sure if
the tool/equipment is properly grounded.
#2275 OPERATOR’S MANUAL
7
®
4. USE ONLY THREE WIRE EXTENSION CORDS with have 3-prong plugs and 3-prong outlets that
accept the tool/equipment’s plug. Repair or replace damaged or worn cords immediately.
5. CAUTION: In all cases, make certain the outlet is properly grounded. If you are not sure if it is, have
a licensed electrician check the outlet.
WARNING: This tool/equipment is for indoor use only. Do not expose to rain or use in
damp locations.
Fig. 1
1. Tools/equipment with three wire grounding plugs (Fig. 1, A) are intended for use on a circuit that has
an outlet that looks like the one illustrated (Fig. 1, B).
2. A temporary adapter (Fig. 1, B & C) may be used to connect this plug to a 2-pole receptacle (Fig. 1, B) if a properly grounded outlet is not available.
3. The temporary adapter should be used only until a properly grounded outlet can be installed by a
qualified electrician.
4. The green colored rigid ear, lug, etc. extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box (Fig. 1, D).
#2275 OPERATOR’S MANUAL
8
®
Extension Cord Guidelines
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one
heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. The table below shows the correct size to be used
according to cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Minimum gauge for Extension Cords (AWG)
Ampere Rating
Not More
More Than
Than
0
6
6
10
10
12
12
16
(When using 120V only)
Total Length of Cord in feet
25
50
100
150
18
18
16
14
16
16
16
12
16
14
14
12
14
12
Not Recommended
1. Be sure your extension cord is properly wired and in good condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
2. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
3. Use a separate electrical circuit for your tools. This circuit must not be less than a #12 wire and
should be protected with a 20 Amp time delayed fuse.
4. Before connecting the motor to the power line, make sure the switch is in the OFF position and the
electric current is rated the same as the current stamped on the motor nameplate. Running at a
lower voltage will damage the motor.
WARNING: This tool must be grounded while in use to protect the operator from electrical
shock.
#2275 OPERATOR’S MANUAL
9
®
COMPONENTS
1
2
3
4
5
6
7
8
9
Fig. 2
1 – Carrying Handle
3 – ON/OFF Switch
5 – Air Flow Valve
7 – Tank Pressure Gauge
9 – Rubber Foot
#2275 OPERATOR’S MANUAL
2 – Air Filter
4 – Regulator
6 – Air Regulator Gauge
8 – Drain Valve
10
®
ASSEMBLY INSTRUCTIONS
Unpacking
1. When unpacking, make sure that the machine is intact and undamaged.
2. Please check that the following items are included with your Air Compressor.
– Oil Bottle
– Air Filter
– Oil Breather Cap
3. If any parts are missing or broken, please call our customer services at 1-800-232-1195.
4. Your Air Compressor requires minimum assembly. Remove
the parts from the carton.
Air Filter Installation (Fig. 3)
Fig. 3
This Air Compressor is shipped with a plastic plug in the air filter hole. Before operating this unit, remove the plug and connect the air filter (Fig 3).
Add Oil and Install Oil Breather Cap (Fig. 4 & 5)
1. Your Air Compressor ships without oil in the Crankcase. Oil Breather
Cap
Note: BEFORE STARTING YOU AIR COMPRESSOR YOU
MUST ADD OIL TO THE CRANKCASE AS DESCRIBED BELOW.
2. Place your Air Compressor on level ground.
3. Remove the Oil Shipping Plug from the Oil Fill Hole located on the top of the case cover at the rear of the Air Compressor (Fig. 5).
Fig. 4
Proper
Oil Level
4. Slowly pour the oil into the Oil Fill Hole until the oil level rises to the center of the red dot on the Oil Sight Glass (Fig. 5).
5. Install the Oil Breather Cap into the Oil Fill Hole.
#2275 OPERATOR’S MANUAL
Minimum
Oil Level
Fig. 5
11
®
OPERATION
BEFORE OPERATING YOUR NEW AIR COMPRESSOR complete the following steps.
1. Check that all nuts and bolts are secure.
2. Make sure the oil has been properly added to your Air Compressor.
3. Place your Air Compressor on a firm, level surface in a clean, dry, well ventilated area.
4. Your Air Compressor should be located 12 to 18 inches from walls or any other obstruction which
would interfere with airflow. Your Air Compressor should be located in a temperature controlled area
between 32° and 95°F.
5. Your Air Compressor is designed with heat dissipation fins which allow for proper cooling. Keep
the fins and all other parts clean from dust or dirt. A clean Air Compressor runs cooler and provides
longer service.
6. Do not place rags, containers or other material on top of your Air Compressor.
Power Source Connection
Your Air Compressor is designed to operate on a properly grounded 120 volt, 60HZ, single phase, alternating current (AC) power source with a fused 20 Amp time delayed fuse or circuit breaker. It is
recommended that a qualified electrician verify the ACTUAL VOLTAGE at the receptacle into which
the unit will be plugged and confirm that the receptacle is properly fused and grounded. The use of the
proper circuit size can eliminate nuisance circuit breaker tripping while operating your Air Compressor.
For electrical details see pages 7–9.
Initial Start-Up Procedures
1. Open the Air Tank Drain Valve to permit air to escape, preventing air pressure buildup in the Air
Tank.
2. Run the compressor for a minimum of 20 minutes in this “no-load” position to lubricate the piston.
3. Close Air Tank Drain Valve. Your compressor is ready for use.
4. See pneumatic tool instructions for instructions on how to connect the tool to your Air Compressor.
Depending on the CFM draw of the tools being operated, your new Air Compressor can be used for
operating paint sprayers, air tools, grease guns, airbrushes, caulking guns, abrasive blasters, tire &
plastic toy inflation, spraying weed killer and insecticides, etc. Proper adjustment of the Air Pressure
Regulator is necessary for all of these operations. Refer to the air pressure specifications provided with
the tool you are using.
#2275 OPERATOR’S MANUAL
12
®
General Overview
1. To compress air, the piston moves up and down in the cylinder. On the down stroke air is drawn
in through the valve inlet. The discharge valve remains closed. On the upstroke of the piston air is
compressed.
2. The inlet valve closes and air is forced out through the discharge valve, through the Check Valve,
and into the Air Tank.
3. Working air is not available until the Air Compressor has raised the tank pressure above that required at the air service connection.
4. The air inlet filter openings must be kept clear of obstructions, which could reduce air delivery of the
Air Compressor.
Air Pressure Adjustment
1. Your Air Compressor is supplied with an Air Pressure Regulator. This Regulator adjusts the air pressure.
2. To increase air pressure, turn the Air Regulator clockwise.
3. To decrease air pressure, turn the Air Regulator counterclockwise.
4. The Air Regulator gauge will show the current pressure selected.
MAINTENANCE
Daily (or before each use)
1. Check oil level.
2. Check for any unusual noise or vibration.
3. Be sure all nuts and bolts are tight.
Weekly
1. Clean breather hole on Oil Breather Cap.
2. Drain water from the Air Tank through the Drain Valve.
3. Keep Air Filter clean at all times. Do not operate the Air Compressor with the air filter removed.
4. A dirty Air Filter will not allow your Air Compressor to operate at full capacity. Before you use your
Air Compressor, check the Air Filter to be sure it is clean. If it is dirty replace the filter element.
#2275 OPERATOR’S MANUAL
13
®
Monthly
Inspect air system for leaks by applying soapy water to all joints. Tighten these joints if leaks are discovered.
6 Months (or after 250 hours of operation - whichever comes first)
Change Air Compressor Oil.
Note: Change the oil more often if your Air Compressor is used near paint spraying operations or
in dusty environments.
Checking the Air Compressor Oil
1. P
lace your Air Compressor on a level surface. The oil level should be at the red dot on the Oil Sight
Glass.
2. If oil level is low, remove Oil Breather Cap and add enough oil to bring the oil level to the red dot on
the Oil Sight Glass.
Changing the Air Compressor Oil
Note: This compressor uses only SAE 5W-30 motor oil.
1. Remove the Oil Sight Glass by turning counterclockwise with wrench.
Note: Oil will begin to drain as the Oil Sight Glass is loosened. Make sure a funnel and oil pan are
in place BEFORE loosening the Oil Sight Glass.
2. Once the Oil Sight Glass is removed, tilt your Air Compressor forwards to allow all the oil to drain out of the Crankcase.
3. Once the oil is drained, replace the Oil Sight Glass and securely tighten in place with a wrench. Be careful not to over tighten the Oil Sight Glass, as this could damage the rubber seal.
4. Place your Air Compressor on level surface.
5. Remove the Oil Breather Cap.
6. Slowly pour the oil into the oil fill hole, until the oil level rises to the center of the red dot on the Oil Sight Glass.
7. Install the Oil Breather Cap into the oil fill hole.
8. Always inspect Air Compressor before use, and make sure it is in good working condition. Use compressed air to clean the machine where possible.
#2275 OPERATOR’S MANUAL
14
®
9. Check the power cable to make sure it is intact and free from cracks, bare wires etc.
10.Avoid using solvents when cleaning plastic parts, most plastics are susceptible to damage from the various types of commercial solvents.
#2275 OPERATOR’S MANUAL
15
®
TROUBLESHOOTING
Problem
Cause
Solution
Thermal Overload
Air Compressor
will not start
Low pressure
Safety valve
releasing
Oil discharge in
Air Compressor
Allow to cool and push the reset button
located in the Crankcase close to the Air
Filter.
Blown fuse or circuit breaker tripped. Replace or reset fuse/circuit breaker.
Loose electrical connections
Check wiring connections
Restricted Air Filter
Replace Air Filter
Defective Check Valve
Replace Check Valve
Air leak in Safety Valve
Check valve by pulling on ring. If condition
persists, replace valve
Replace pressure switch
Defective Pressure Switch
Too much oil in Crankcase
Drain Crankcase and refill to proper level on
Oil Sight Glass
Compressor overheated
Reduce air pressure regulation.
Restricted Oil Breather Cap
Clean or replace Oil Breather Cap.
If trouble persists please call our customer service
1-800-232-1195, M–F 8–5 (CST)
SERVICE
1. Mechanical and/or electrical tool service is to be performed only by professional qualified repair
personnel. Service performed by unqualified personnel may result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Use of unauthorized parts or failure to
follow maintenance instructions may create a risk of electrical shock or injury.
NOTE: If any parts are damaged or missing, do not attempt to plug in the power cord and turn the
switch on until the damaged or missing parts are obtained and are installed correctly.
#2275 OPERATOR’S MANUAL
16
®
EXPLODED VIEW
66
#2275 OPERATOR’S MANUAL
17
®
PARTS LIST
Part # Stock # Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
2274-001
2274-002
2274-003
2274-004
2274-005
2274-006
2274-007
2274-008
2274-009
2274-010
2274-011
2274-012
2274-013
2274-014
2274-015
2274-016
2274-017
2274-018
2274-019
2274-020
2274-021
2274-022
2274-023
2274-024
2274-025
2274-026
2274-027
2274-028
2274-029
2274-030
2274-031
2274-032
2274-033
Crankcase
Crank Shaft
Gasket
Crankcase Cover
Bolt
O-ring
Oil Sight Glass
Bolt
Washer
Oil Breather Cap
Bolt
Connecting Rod
Circle Clip
Piston Pin
Piston
Piston Oil Ring
Piston Ring
Gasket
Cylinder
Washer
Bolt
Valve Gasket
Valve
Valve Plate
Gasket
Cylinder Head Gasket
Cylinder Head
Elbow Connector
Washer
Bolt
Air Filter
Capacitor
Washer
#2275 OPERATOR’S MANUAL
Part # Stock #
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
2274-034
2274-035
2274-036
2274-037
2274-038
2274-039
2274-040
2274-041
2274-042
2274-043
2275-044
2275-045
2275-046
2275-047
2275-048
2275-049
2274-062
2275-051
2274-049
2275-053
2274-064
2274-061
2275-056
2275-057
2275-058
2274-057
2275-060
2275-061
2275-062
2275-063
2275-064
2274-050
2274-069
Description
Bolt
Motor Cover
Bolt
Fan
Motor Back Cover
Stator
Bearing
Rotor
Bearing
Oil Seal
Exhaust Pipe Nut
Exhaust Pipe
Exhaust Pipe Nut
Air Tank
Carrying Handle
Air Flow Valve
Regulator
Connector
Safety Valve
Pressure Switch
Tank Pressure Gauge
Air Regulator Gauge
Unloading Nut
Unloading Pipe
Unloading Nut
Check Valve
Wire Cable
Power Cord
Rubber Foot
Washer
Bolt
Drain Valve
Overload Reset
18
®
ONE (1) YEAR LIMITED WARRANTY
WEN® is committed to building tools that are dependable for years. Our warranties are consistent with
our commitment and dedication to quality.
ONE (1) YEAR LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE.
GREAT LAKES TECHNOLOGIES, LLC (“Seller") warrants to the original purchaser only, that all WEN
consumer power tools will be free from defects in material or workmanship for a period of one (1) year
from date of purchase. Ninety (90) days for all WEN Products, if the tool is used for professional or
commercial use.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this One (1) Year Limited
Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which
have not been misused, carelessly handled, or misrepaired by persons other than Seller or Authorized
Service Center. To make a claim under this Limited Warranty, you must return the entire power tool
product; transportation prepaid, to Great Lakes Technologies, LLC, 501 Davis Road, Elgin, IL 60123.
Include a legible copy of the original receipt, which lists the date of purchase (month and year) and the
name of the company purchased from.
THIS LIMITED WARRANTY DOES NOT APPLY TO ANY ACCESSORY ITEMS INCLUDED WITH THE
TOOL SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS OR TO ANY REPLACEMENT
PARTS LISTED UNDER MAINTENANCE.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1) YEAR FROM DATE OF
PURCHASE. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE
SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE ELECTRIC TOOLS, BENCH POWER
TOOLS, OUTDOOR POWER EQUIPMENT AND PNEUMATIC TOOLS SOLD WITHIN THE UNITED
STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT WEN CUSTOMER SUPPORT.
#2275 OPERATOR’S MANUAL
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising