Manual for Mud Ring - AV-iQ
Crestron MMK-4000L & WMKM-4000L
Mud Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2004 Crestron Electronics, Inc.
Crestron MMK-4000L & WMKM-4000L
Mud Mount Kits
Mud Mount Kits: MMK-4000L &
WMKM-4000L
Description
Mud Mount Kits are the preferred mounting option for the Crestron Isys®
TPS-4000L series of lectern/wall-mounted video touchpanel when cutouts made in
the drywall for touchpanel installation are too large. These kits provide support for
additional plastering that can be applied to hide large irregularities in the touchpanel
cutout.
There are two Mud Mount Kits. The MMK-4000L is a pre-construction accessory.
Pre-construction refers to framed walls prior to hanging drywall. This accessory
must be used with either the Pre-Construction Mount Kit (PMK-4000L) or Back Box
Kit (BB-4000L).
The WMKM-4000L is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support from a stud.
NOTE: If necessary, consult the latest revision of the TPS-4000L Operations Guide
(Doc. 6301) for a complete list of mounting options.
Supplied Hardware
The MMK-4000L consists of three parts. These parts produce an assembly that
attaches to the PMK-4000L or BB-4000L. The WMKM-4000L consists of the same
three parts that make up the MMK-4000L as well as one mounting plate. The
mounting plate is the part that provides the necessary support for post-construction
applications.
Supplied Hardware of the MMK-4000L and WMKM-4000L
Installation Guide – DOC. 6303
DESCRIPTION
PART NUMBER
QUANTITY
Metal Plate, Mounting
(WMKM-4000L only)
Metal Plate, Mud Ring
Metal Plate, Fastener
Hardware, Push-On Fastener
2011515
1
2011517
2004825
2004121
1
2
4
Mud Mount Kits: MMK-4000L & WMKM-4000L • 1
Mud Mount Kits
Crestron MMK-4000L & WMKM-4000L
The dimensions of the MMK-4000L/WMKM-4000L are shown below.
Dimensional Drawing
0.38 in
(0.95 cm)
5.91 in
(15.01 cm)
8.99 in
(22.84 cm)
0.38 in
(0.95 cm)
0.06 in
(0.15 cm)
12.63 in
(32.08 cm)
MOUNTING PLATE FOR
WMKM-4000L
FASTENER PLATE FOR
WMKM-4000L AND MMK-4000L
9.34 in
(23.73 cm)
12.79 in
(32.49 cm)
0.05 in
(0.13 cm)
2.26 in
(5.73 cm)
MUD RING PLATE FOR
WMKM-4000L AND MMK-4000L
Drywall Cutout Dimensions
7 3132 in
(202 mm)
819 64 in MAX
(211 mm MAX)
DO NOT EXCEED
THIS DIMENSION
118 in
1113 32 in MAX
(28 mm)
(290 mm MAX)
DO NOT EXCEED
THIS DIMENSION
2 • Mud Mount Kits: MMK-4000L & WMKM-4000L
Installation Guide – DOC. 6303
Crestron MMK-4000L & WMKM-4000L
Mud Mount Kits
Installation
This section provides an installation procedure for each Mud Mount Kit. The
procedure for the MMK-4000L starts below and the “WMKM-4000L Procedure”
starts on page 5.
MMK-4000L Procedure
The procedure in this section provides the necessary steps for the assembly of the
MMK-4000L to either the PMK-4000L or BB-4000L. It is assumed that the
PMK-4000L or BB-4000L has been secured to the stud according to the procedures
in the latest revisions of their respective Installation Guides (Doc. 6304 and Doc.
6305, respectively). Also, it is assumed that drywall is in place and a rectangular
cutout for the touchpanel is made in the drywall (refer to the Drywall Cutout
dimensions on the previous page for cutout dimensions).
Complete the steps in the order provided. The only tools or materials required and
not supplied are a drywall saw or equivalent, four standard drywall screws, #2
Phillips screwdriver, a level, and tools/material to apply drywall joint compound.
NOTE: The illustrations in this procedure show the installation of the MMK-4000L
with the PMK-4000L. Even though the illustrations only show the PMK-4000L, they
are identical for the BB-4000L as well.
1.
Pass a fastener plate through the opening and align its two center holes
with the top two pins on the PMK-4000L. Verify that the pins on the
fastener plate are not between the fastener plate and the PMK-4000L.
Refer to the illustration after this step for visual guidance.
Secure Fastener Plates to PMK-4000L (or BB-4000L)
PMK-4000L
(4) PUSH-ON FASTENER
(2004121)
(2) FASTENER PLATE
(2004825)
Installation Guide – DOC. 6303
Mud Mount Kits: MMK-4000L & WMKM-4000L • 3
Mud Mount Kits
Crestron MMK-4000L & WMKM-4000L
2.
Slide a push-on fastener over each pin of the PMK-4000L (or
BB-4000L) to loosely secure the fastener plate and the mounting plate.
Do not push the push-on fasteners all the way down onto the pins. Slide
them on enough to keep the fastener plate and mounting plate as one
fastener/mounting plate assembly.
3.
Use the second fastener plate and repeat steps 1 and 2 using the lower
two PMK-4000L (or BB-4000L) pins.
NOTE: When installing into the PMK-4000L, verify that the 18 AWG bus wire
securing the cables for the touchpanel remain attached.
4.
Verify that the drywall cutout meets the measurements specified on
page 2.
5.
Insert the symmetrical mud ring plate into the opening, as shown in the
illustration after this step.
Insert and Secure Mud Ring Plate into PMK-4000L (or BB-4000L)
PMK-4000L
DRYWALL
FLANGE
HOLES FOR DRYWALL SCREWS (PROVIDED BY
OTHER), SCREW LENGTH SHOULD NOT EXCEED
DRYWALL THICKNESS BY MORE THAN 1/2".
MUD RING PLATE
(2011517)
6.
When the mud ring plate is in position, bend the top two flanges of the
plate upward and the bottom two flanges downward.
4 • Mud Mount Kits: MMK-4000L & WMKM-4000L
•
If mounting into the PMK-4000L, bend the flanges
approximately 90 degrees.
•
If mounting into the BB-4000L, bend the flanges back as far
as they can go.
Installation Guide – DOC. 6303
Crestron MMK-4000L & WMKM-4000L
Mud Mount Kits
7.
Use four standard drywall screws (length should not exceed drywall
thickness by more than ½ inch) to secure the mud ring plate to the rest
of the assembly. The screws pass through the clearance holes in the
PMK-4000L (or BB-4000L) and are secured in the extruded holes of
the fastener plates.
8.
Verify that the mud ring plate is level.
NOTE: Do not over tighten screws. Doing so may over-dimple or rip the mud ring
plate.
9.
Use a #2 Phillips screwdriver and tighten the drywall screws by hand
so that they slightly dimple into the holes in the mud ring plate.
10. Apply drywall joint compound as needed to finish the cutout. Avoid
covering the four tapped mounting holes.
11. Run the necessary cables for the touchpanel and secure them behind the
drywall.
12. When dry, the TPS-4000L can be installed using the four tapped holes
in the PMK-4000L. Refer to the latest revision of the TPS-4000L
Operations Guide (Doc. 6301) for details.
WMKM-4000L Procedure
The procedure in this section provides the necessary steps for the assembly and
installation of the WMKM-4000L into a wall. Complete the steps in the order
provided. The only tools or materials required and not supplied are a drywall saw or
equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and
tools/material to apply drywall joint compound.
1.
Insert the two pins on one fastener plate into the top two outer holes on
the mounting plate, as shown in the following illustration.
Create the Fastener/Mounting Plate Assembly
(1) MOUNTING PLATE
(2011515)
(4) PUSH-ON FASTENER
(2004121)
(2) FASTENER PLATE
(2004825)
Installation Guide – DOC. 6303
Mud Mount Kits: MMK-4000L & WMKM-4000L • 5
Mud Mount Kits
Crestron MMK-4000L & WMKM-4000L
2.
Slide a push-on fastener over each pin on the fastener plate to loosely
secure the fastener plate and the mounting plate. Do not push the pushon fasteners all the way down onto the pins. Slide them on enough to
keep the fastener plate and mounting plate as one fastener/mounting
plate assembly.
3.
Use the second fastener plate and repeat steps 1 and 2 using the lower
two PMK-4000L pins.
4.
Locate an area on the wall that is free of miscellaneous wiring and
studs.
5.
Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level as possible. The mounting plate allows for only
minor leveling adjustments.
6.
Use the drywall saw or equivalent to produce a level, rectangular cutout
in the drywall as shown on page 2.
7.
Insert the symmetrical mud ring plate into the opening, as shown in the
illustration after this step.
Insert the Mud Ring Plate into the Opening
IMPORTANT:
PLEASE MAKE DRYWALL CUTOUT AS
LEVEL AND CLEAN AS POSSIBLE.
THE MOUNTING PLATE ALLOWS FOR ONLY MINOR
ADJUSTMENT OF THE TPS-4000L.
FLANGE
MUD RING PLATE
(2011517)
HOLES FOR DRYWALL SCREWS (PROVIDED BY
OTHER), SCREW LENGTH SHOULD NOT EXCEED
DRYWALL THICKNESS BY MORE THAN 1/2").
8.
Carefully pass the fastener/mounting plate assembly through the
opening and rest the assembly against the interior surface of the
drywall. Verify that the fastener plates are between the mounting plate
and the drywall.
6 • Mud Mount Kits: MMK-4000L & WMKM-4000L
Installation Guide – DOC. 6303
Crestron MMK-4000L & WMKM-4000L
9.
Mud Mount Kits
When the fastener/mounting plate assembly is in position, bend the top
two flanges of the mud ring upward (approximately 90 degrees) and the
bottom two flanges downward (approximately 90 degrees). Refer to the
illustration after this step.
NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It
allows for minor adjustments to the TPS-4000L during installation.
Bend Flanges
10. Use four standard drywall screws (of adequate length) to secure the
plate to the fastener/mounting plate assembly. The screws pass through
the clearance holes in the plate and are secured in the extruded holes of
the fastener plates.
11. Verify that the plate is level before tightening.
NOTE: Do not over tighten screws. Doing so may over-dimple or rip the plate.
12. Use a #2 Phillips screwdriver and tighten the drywall screws by hand
so that they slightly dimple into the holes in the mud ring plate.
13. Run the necessary cables for the touchpanel and secure them behind the
drywall.
14. Apply drywall joint compound as needed to finish the cutout. Avoid
covering the four tapped mounting holes.
15. When dry, the TPS-4000L can be installed using the four tapped holes
in the mounting plate. Refer to the latest revision of the TPS-4000L
Operations Guide (Doc. 6301) for details.
Installation Guide – DOC. 6303
Mud Mount Kits: MMK-4000L & WMKM-4000L • 7
Mud Mount Kits
Crestron MMK-4000L & WMKM-4000L
Further Inquiries
If after reviewing this Installation Guide, you cannot locate specific information or
have questions, please take advantage of Crestron's award winning customer service
team by calling:
•
In the US and Canada, call Crestron’s corporate headquarters at
1-888-CRESTRON [1-888-273-7876].
•
In Europe, call Crestron International at +32-15-50-99-50.
•
In Asia, call Crestron Asia at +852-2341-2016.
•
In Latin America, call Crestron Latin America at +5255-5093-2160.
•
In Australia and New Zealand, call Crestron Control Solutions at
+61-2-9737-8203.
You can also log onto the online help section of the Crestron website
(www.crestron.com) to ask questions about Crestron products. First-time users will
need to establish a user account to fully benefit from all available features.
As of the date of manufacture, the MMK-4000L and WMKM-4000L have been
tested and found to comply with specifications for CE marking.
Future Updates
As Crestron adds improvements to the MMK-4000L or WMKM-4000L, additional
information may be made available as manual updates. These updates are solely
electronic and serve as intermediary supplements prior to the release of a complete
technical documentation revision.
Check the Crestron website (www.crestron.com) periodically for manual update
availability and its relevance. Updates are available from the Download | Product
Manuals section and are identified as an “Addendum” in the Download column.
8 • Mud Mount Kits: MMK-4000L & WMKM-4000L
Installation Guide – DOC. 6303
Crestron MMK-4000L & WMKM-4000L
Mud Mount Kits
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange, or service without prior
authorization from CRESTRON. To obtain warranty service for CRESTRON
products, contact the factory and request an RMA (Return Merchandise
Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number, and return address.
2.
Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped
freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J., or its authorized
subsidiaries, with RMA number clearly marked on the outside of all cartons.
Shipments arriving freight collect or without an RMA number shall be subject to
refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a
15% restocking fee, plus shipping costs, on any products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to
be non-warranty, return freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1)
year; touchscreen display and overlay components are covered for 90 days; batteries and
incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the
dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in
any application other than that for which it was intended, or if it has been subjected to misuse,
accidental damage, modification, or improper installation procedures. Furthermore, this warranty
does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for
any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be
covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed
or implied, nor authorizes any other party to offer any warranty, including any implied warranties
of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed
by law are limited to the terms of this limited warranty. This warranty statement supercedes all
previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft
Corporation.
Installation Guide – DOC. 6303
Mud Mount Kits: MMK-4000L & WMKM-4000L • 9
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Installation Guide – DOC. 6303
10.04
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising