TP-LINK TD-W9970 Owner's Manual

PDF Download

Document

TD-W9970

300Mbps Wireless N USB VDSL/ADSL Modem Router

Rev: 1.0.1

1910011459

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only

Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

RF Exposure Information

This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.

The device complies with RF specifications when the device used at 20 cm from your body.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country

Belarus

Norway

Restriction Reason/remark

Not implemented

Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund on

Svalbard.

Italy Implemented

Russian

Federation

Limited implementation

The public use is subject to general authorisation by the respective service provider.

1. SRD with FHSS modulation

1.1. Maximum 2.5 mW e.i.r.p.

1.2. Maximum 100 mW e.i.r.p. Permitted for use SRD for outdoor applications without restriction on installation height only for purposes of gathering telemetry information for automated monitoring and resources accounting systems.

Permitted to use SRD for other purposes for outdoor applications only when the installation height is not exceeding

10 m above the ground surface.

1.3.Maximum 100 mW e.i.r.p. Indoor applications.

2. SRD with DSSS and other than FHSS wideband

modulation

2.1. Maximum mean e.i.r.p. density is 2 mW/MHz. Maximum

100 mW e.i.r.p.

2.2. Maximum mean e.i.r.p. density is 20 mW/MHz. Maximum

100 mW e.i.r.p. It is permitted to use SRD for outdoor applications only for purposes of gathering telemetry information for automated monitoring and resources accounting systems or security systems.

2.3. Maximum mean e.i.r.p. density is 10 mW/MHz. Maximum

100 mW e.i.r.p. Indoor applications.

Ukraine Limited implementation e.i.r.p. ≤100 mW with built-in antenna with amplification factor up to 6 dBi.

ATTENTION: Due to EU law, the country settings must be identical to the country where the device is operating (important due to non-harmonised frequencies in the EU).

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1） This device may not cause interference, and

2） This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1） l’appareil ne doit pas produire de brouillage;

2） l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice

注意！

依據

低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、

加大功率或變更原設計之特性或功能

。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通行

；經發現有干擾現象

時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。

低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

BSMI Notice

安全諮詢及注意事項

 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

 注意防潮，請勿將水或其他液體潑灑到本產品上。

 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。



請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

 Adapter shall be installed near the equipment and shall be easily accessible.

 The plug considered as disconnect device of adapter.

 Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us.

This product can be used in the following countries:

AT BG BY CA CZ

Explanation of the symbols on the product label

Symbol Explanation

DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to

European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 300Mbps Wireless N USB VDSL/ADSL Modem Router

Model No.: TD-W9970

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,

Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents

EN 300 328 V1.8.1

EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1

EN 55022: 2010 + AC: 2011

EN 55024: 2010

EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013

EN 50385: 2002

EN 50581: 2012

The product carries the CE Mark:

Person responsible for making this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue: 2015-11-25

TP-LINK TECHNOLOGIES CO., LTD

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,

Shennan Rd, Nanshan, Shenzhen, China

Package Contents .................................................................................................... 1

Chapter 1.

Product Overview ................................................................................... 2

1.1

Overview of the Modem Router ..................................................................................... 2

1.2

Main Features ............................................................................................................... 3

1.3

Panel Layout ................................................................................................................. 4

1.3.1

The Front Panel ................................................................................................................... 4

1.3.2

The Back Panel .................................................................................................................... 6

Chapter 2.

Connecting the Modem Router ............................................................. 7

2.1

System Requirements ................................................................................................... 7

2.2

Installation Environment Requirements ......................................................................... 7

2.3

Connecting the Modem Router ..................................................................................... 8

Chapter 3.

Quick Installation Guide ........................................................................ 9

3.1

TCP/IP Configuration .................................................................................................... 9

3.2

Quick Installation Guide .............................................................................................. 10

Chapter 4.

Configuring the Modem Router .......................................................... 15

4.1

Login ........................................................................................................................... 15

4.2

Status ......................................................................................................................... 15

4.3

Quick Setup ................................................................................................................ 17

4.4

Operation Mode .......................................................................................................... 17

4.5

Network ...................................................................................................................... 17

4.5.1

WAN Settings ..................................................................................................................... 18

4.5.2

3G/4G Settings................................................................................................................... 35

4.5.3

Interface Grouping ............................................................................................................. 37

4.5.4

LAN Settings ...................................................................................................................... 39

4.5.5

IPv6 LAN Settings .............................................................................................................. 41

4.5.6

MAC Clone ......................................................................................................................... 43

4.5.7

ALG Settings ...................................................................................................................... 43

4.5.8

DSL Settings ...................................................................................................................... 45

4.5.9

IPSec VPN ......................................................................................................................... 45

4.6

IPTV............................................................................................................................ 50

4.7

DHCP Server .............................................................................................................. 52

4.7.1

DHCP Settings ................................................................................................................... 52

4.7.2

Clients List .......................................................................................................................... 54

4.7.3

Address Reservation .......................................................................................................... 54

4.7.4

Conditional Pool ................................................................................................................. 55

4.8

Wireless ...................................................................................................................... 56

4.8.1

Basic Settings .................................................................................................................... 56

4.8.2

WPS Settings ..................................................................................................................... 58

4.8.3

Wireless Security ............................................................................................................... 61

4.8.4

Wireless Schedule ............................................................................................................. 63

4.8.5

Wireless MAC Filtering ...................................................................................................... 63

4.8.6

Wireless Advanced ............................................................................................................ 65

4.8.7

Wireless Status .................................................................................................................. 66

4.9

Guest Network ............................................................................................................ 67

4.9.1

Basic Settings .................................................................................................................... 67

4.9.2

Guest Network Status ........................................................................................................ 68

4.10

USB Settings .............................................................................................................. 69

4.10.1

USB Mass Storage ........................................................................................................... 69

4.10.2

User Accounts .................................................................................................................. 70

4.10.3

Storage Sharing ................................................................................................................ 71

4.10.4

FTP Server ....................................................................................................................... 72

4.10.5

Media Server .................................................................................................................... 74

4.10.6

Print Server ....................................................................................................................... 75

4.11

Route Settings ............................................................................................................ 76

4.11.1

Default Gateway ............................................................................................................... 76

4.11.2

Static Route ...................................................................................................................... 76

4.11.3

RIP Settings ...................................................................................................................... 77

4.12

IPv6 Route Settings .................................................................................................... 78

4.12.1

IPv6 Default Gateway ....................................................................................................... 78

4.12.2

IPv6 Static Route .............................................................................................................. 78

4.13

Forwarding .................................................................................................................. 79

4.13.1

Virtual Servers .................................................................................................................. 79

4.13.2

Port Triggering .................................................................................................................. 81

4.13.3

DMZ .................................................................................................................................. 83

4.13.4

UPnP ................................................................................................................................ 83

4.14

Parental Control .......................................................................................................... 84

4.15

Firewall ....................................................................................................................... 85

4.15.1

Rule .................................................................................................................................. 86

4.15.2

LAN Host .......................................................................................................................... 87

4.15.3

WAN Host ......................................................................................................................... 88

4.15.4

Schedule ........................................................................................................................... 89

4.16

IPv6 Firewall ............................................................................................................... 90

4.16.1

IPv6 Rule .......................................................................................................................... 90

4.16.2

IPv6 LAN Host .................................................................................................................. 92

4.16.3

IPv6 WAN Host ................................................................................................................. 93

4.16.4

IPv6 Schedule ................................................................................................................... 93

4.17

IPv6 Tunnel ................................................................................................................. 94

4.18

Bandwidth Control ....................................................................................................... 97

4.19

IP & MAC Binding ....................................................................................................... 98

4.19.1

Binding Settings ................................................................................................................ 98

4.19.2

ARP List ............................................................................................................................ 99

4.20

Dynamic DNS ........................................................................................................... 100

4.21

Diagnostic ................................................................................................................. 100

4.22

System Tools ............................................................................................................ 101

4.22.1

System Log ..................................................................................................................... 101

4.22.2

Time Settings .................................................................................................................. 102

4.22.3

Manage Control .............................................................................................................. 103

4.22.4

CWMP Settings .............................................................................................................. 104

4.22.5

SNMP Settings ............................................................................................................... 105

4.22.6

Backup & Restore ........................................................................................................... 106

4.22.7

Factory Defaults.............................................................................................................. 106

4.22.8

Firmware Upgrade .......................................................................................................... 107

4.22.9

Reboot ............................................................................................................................ 108

4.22.10

Statistics ...................................................................................................................... 108

4.23

Logout ....................................................................................................................... 110

Appendix A: Specifications ................................................................................. 111

Appendix B: Troubleshooting ............................................................................. 112

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Package Contents

The following contents should be found in your package:



One TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router

One Power Adapter for TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router

Quick Installation Guide

Technical Support card

One RJ45 cable

Two RJ11 cables

One DSL splitter

One Resource CD for TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router, including:

• This User Guide

• Other Helpful Information

 Note:

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Chapter 1. Product Overview

Thank you for choosing the TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router.

1.1 Overview of the Modem Router

The TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router integrates 4-port Switch,

Firewall, NAT-Router and Wireless AP. The Modem Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.

The TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router utilizes integrated VDSL2 transceiver and high speed MIPS CPU. The modem router supports full-rate VDSL2 connectivity conforming to the ITU and ANSI specifications.

In addition to the basic DMT physical layer functions, the VDSL2 PHY supports dual latency

VDSL2 framing (fast and interleaved) and the I.432 ATM Physical Layer.

The modem router provides up to 300Mbps (2.4GHz) wireless connection with other 802.11n wireless clients. The incredible speed makes it ideal for handling multiple data streams at the same time, which ensures your network stable and smooth. The performance of this 802.11n wireless Router will give you the unexpected networking experience at speed much faster than 802.11g. It is also compatible with all IEEE 802.11g and IEEE 802.11b products.

With multiple protection measures, including SSID broadcast control and wireless LAN 64/128

WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), as well as advanced Firewall protections, the TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router provides complete data privacy.

The modem router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server and DMZ host for Port Triggering, and then the network administrators can manage and monitor the network in real time with the remote management function.

Since the modem router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide. Before installing the modem router, please look through this guide to know all the modem router’s functions.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

1.2 Main Features

 Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps (2.4GHz).

 Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.

 Provides external splitter.

 Adopts Advanced DMT modulation and demodulation technology.

 Supports bridge mode and Router function.

 Multi-user sharing a high-speed Internet connection.

 Downstream data rates up to 100Mbps, upstream data rates up to 60Mbps.

 Supports long transfers, the max line length can reach to 6.5Km.

 Supports remote configuration and management through SNMP and CWMP.

 Supports PPPoE, it allows connecting the internet on demand and disconnecting from the

Internet when idle.

 Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit.

 High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.

 Compatible with all mainstreams DSLAM (CO).

 Provides integrated access of internet and route function which face to SOHO user.

 Real-time Configuration and device monitoring.

 Supports Multiple PVC (Permanent Virtual Circuit).

 Built-in DHCP server.

 Built-in firewall, supporting IP/MAC filter and URL filter.

 Supports Virtual Server, DMZ host and Port Triggering.

 Supports Dynamic DNS, UPnP and Static Routing.

 Supports system log and flow Statistics.

 Supports firmware upgrade and Web-Management page.

 Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security.

 Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).

 Supports USB Storage Sharing, Print Server, FTP Server, Media Server.

 Supports Ethernet WAN (EWAN).

 Supports Bandwidth Control.

 Supports IPv6.

 Supports ADSL and VDSL.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

1.3 Panel Layout

1.3.1 The Front Panel

Figure 1-1

The modem router’s LEDs are located on the front panel (View from left to right). They indicate the device’s working status. For details, please refer to LED Explanation.

LED Explanation:

Name Status

On System start-up complete.

Indication

Flash

(Power)

System starting up or device updating.

Off

The modem router is off. Please ensure that the power adapter is connected correctly.

(DSL)

Flash

Off

DSL line is synchronized and ready to use.

The DSL negotiation is in progress.

There is no connection to the DSL Port or DSL synchronization

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide fails. Please refer to

Note 1 for troubleshooting.

On The network is available with a successful Internet connection.

(Internet)

Off

There is no successful Internet connection or the modem router is operating in Bridge mode. Please refer to

Note 2 for

troubleshooting.

(Wireless)

Off

(WPS)

(USB)

On/Off

Flash

The wireless function is working properly.

The wireless function is disabled.

It turns on when a wireless device has been successfully connected to the network via WPS. After about 5 minutes, the

WPS LED will turn off.

WPS handshaking is in process and will continue for about 2 minutes. Please press the WPS/RESET button on other wireless devices that you want to add to the network while the LED is flashing.

The USB device is identified and ready to use.

The USB device is being identified.

Off No USB device is plugged in to the USB port.

On There is a device connected to this LAN port.

(LAN1-4)

Off There is no device connected to this LAN port.

 Note:

1. If the DSL LED is off, please check your Internet connection first. Refer to 2.3 Connecting the

Modem Router for more information about how to make Internet connection correctly. If you

have already made a right connection, please contact your IS P to make sure if your Internet service is available now.

2. If the Internet LED is off, please check your DSL LED first. If your DSL LED is also off, please

refer to Note 1 . If your DSL LED is GREEN ON, please check your Internet configuration. You

may need to check this part of information with your ISP and make sure everything have been input correctly.

3. You can also refer to 4.8.2 WPS Settings for more information.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

1.3.2 The Back Panel

Figure 1-2

 VDSL: Through the port, you can connect the modem router with the telephone. Or you can

connect them by an external separate splitter. For details, please refer to 2.3 Connecting the

Modem Router .

 LAN4/WAN, LAN3, LAN2, LAN1: Through these ports, you can connect the modem router to your PC or the other Ethernet network devices. In wireless router mode you will be able to connect to Cable/FTTH/VDSL/ADSL device.

 USB: The USB port connects to a USB storage device, a USB printer or a 3G/4G Modem.

 WiFi: The switch for the WiFi function. Press the button to enable/disable the WiFi function.

 WPS/RESET: The switch for the WPS function or resetting the modem router.

•

WPS function: For details, please refer to 4.8.2 WPS Settings.

• Reset the modem router: There are two ways to reset the modem router's factory defaults.

Method one: With the modem router powered on, use a pin to press and hold the

WPS/Reset button for at least 5 seconds. And the modem router will reboot to its factory default settings.

Method two: Restore the default setting from 4.22.7 Factory Defaults of the modem

router's Web-based management page.

 ON/OFF: The switch for the power.

 POWER: The Power plug is where you will connect the power adapter.

 Antennas: Used for wireless operation and data transmit.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Chapter 2. Connecting the Modem Router

2.1 System Requirements

 Broadband Internet Access Service (DSL/Cable/Ethernet).

 PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.

 TCP/IP protocol on each PC.

 Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

2.2 Installation Environment Requirements

 The Product should not be located where it will be exposed to moisture or excessive heat.

 Place the modem router in a location where it can be connected to the various devices as well as to a power source.

 Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard.

 The modem router can be placed on a shelf or desktop.

 Keep away from the strong electromagnetic radiation and the device of electromagnetic sensitive.

Generally,

shown in

TD-W9970 is placed on a horizontal surface. The device also can be mounted on the wall as

Figure 2-1 .

Figure 2-1 Wall-mount install

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

 Note:

The diameter of the screw, 3.5mm<D<7.8mm, and the distance of two screws is 107.5mm. The screw that project from the wall need around 4mm based, and the length of the screw need to be at least 20mm to withstand the weight of the product.

2.3 Connecting the Modem Router

Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it.

Step 1: Connect the DSL Line.

Method one: Plug one end of the twisted-pair DSL cable into the VDSL port on the rear panel of TD-W9970, and insert the other end into the wall socket.

Method two：You can use a separate splitter. External splitter can divide the data and voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports:

• LINE: Connect to the wall jack

• PHONE: Connect to the phone sets

• MODEM: Connect to the VDSL port of TD-W9970

Plug one end of the twisted-pair DSL cable into the VDSL port on the rear panel of

TD-W9970. Connect the other end to the MODEM port of the external splitter.

Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s

Ethernet port or a regular hub/switch port, and the other end to the LAN port on the modem router TD-W9970.

Step 3: Power on the computers and LAN devices.

Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to an electrical outlet or power extension. The electrical outlet shall be installed near the device and shall be easily accessible.

Figure 2-2

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Chapter 3. Quick Installation Guide

This chapter will show you how to configure the basic functions of your TD-W9970 300Mbps

Wireless N USB VDSL/ADSL Modem Router using Quick Setup Wizard within minutes.

3.1 TCP/IP Configuration

The default IP address of the TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router is

192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.

Connect the local PC to the LAN/WAN port of the modem router. And then you can configure the

IP address for your PC in the following way.

 Obtain an IP address automatically

1) Set up the TCP/IP Protocol in " Obtain an IP address automatically" mode on your PC.

If you need instructions as to how to do this, please refer to Appendix B: Trouble shooting .

2) Then the built-in DHCP server will assign IP address for the PC.

Now, you can run the Ping command in the command prompt to verify the network connection.

Please click the Start menu on your desktop, select run tab, type cmd or command in the field and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.

If the result displayed is similar to the screen below, the connection between your PC and the modem router has been established.

Figure 3-1

If the result displayed is similar to the screen shown below, it means that your PC has not connected to the modem router.

Figure 3-2

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

You can check it following the steps below:

1) Is the connection between your PC and the modem router correct?

The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit.

2) Is the TCP/IP configuration for your PC correct?

If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254.

3.2 Quick Installation Guide

With a Web-based management page, it is easy to configure and manage the TD-W9970

300Mbps Wireless N USB VDSL/ADSL Modem Router. The Web-based management page can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet

Explorer, Mozilla Firefox or Apple Safari.

1. To access the configuration utility, open a web-browser and type the default address http://tplinkmodem.net/ in the address field of the browser.

Figure 3-3

After a moment, a login window will appear, similar to the Figure 3-4. Enter

admin for the

User Name and Password, both in lower case letters. Then click the Login button or press the

Enter key.

Figure 3-4

 Note:

1) Do not mix up the user name and password with your DSL account user name and password which are needed for PPP connections.

2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy.

Go to Tools menu→Internet Options→Connections→LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.

After your successful login, you will see the Login screen as shown in Figure 3-5. Click

Quick

Setup menu to access Quick Setup Wizard and then click Next.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 3-5

3. Select your Region and Time Zone from the drop-down list, then click Next.

Figure 3-6

4. Select “Yes” to auto detect your connection type and then click Next. It will take about two minutes, please wait.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 3-7

5. Configure parameters for WAN connection. Here we take PPPoE as an example. Enter the username and password provided by your ISP. Click Next.

Figure 3-8

6. 3G/4G Router Mode can be set as a backup Internet access method. If you do not want to configure 3G/4G settings now, just click Next to continue.

Figure 3-9

7. The wireless function is enabled by default. You can rename your wireless network name and create your own password in this page. The default wireless name is TP-LINK_XXXXXX.

Click Next to continue.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 3-10

8. On this page, please confirm all parameters. Click Back to modify or click the Save button to save your configuration.

Figure 3-11

9. You will see the Complete screen below, click Finish to complete these settings.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 3-12

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Chapter 4. Configuring the Modem Router

This chapter will show each Web page's key function and the configuration.

4.1 Login

After your successful login, you will see the twenty-two main menus on the left of the Web-based management page. On the right, there are the corresponding explanations and instructions.

The detailed explanations for each Web page’s key function are listed below.

4.2 Status

Choose “ Status”, you can see the corresponding information about Device Information, DSL,

WAN, LAN and Wireless.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-1

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

4.3 Quick Setup

Please refer to Section 3.2 Quick Installation Guide .

4.4 Operation Mode

Choose “

Operation Mode”, and you will see the screen as shown in Figure 4-2. Select your

desired mode and then click Save.

Figure 4-2

 DSL Modem Router Mode: In this mode, the device enables multi-users to share Internet via

ADSL/VDSL using its VDSL port and share it wirelessly at 300Mbps wireless 802.11n speeds.

 3G/4G Router Mode: In this mode, the device allows multi-users to share a 3G/4G mobile broadband connection via wired or wireless connection.

 Wireless Router Mode: In this mode, the device enables multi-users to share Internet via

Ethernet WAN (EWAN) using its interchangeable LAN/WAN port and share it wirelessly at

300Mbps wireless 802.11n speeds.

After you click the Save button, the Note Dialog will appear. Click OK and then the modem router will reboot. Please wait.

Note Dialog

4.5 Network

Choose “ Network”, there are many submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

4.5.1 WAN Settings

Choose “ Network”“WAN Settings”, and you will see the WAN Port Information Table in the

screen similar to Figure 4-3.

4.5.1.1 VDSL WAN Settings

For VDSL mode, there are four different connection types, which are Static IP, Dynamic IP,

PPPoE and Bridge. You can select the corresponding types according to your needs.

Figure 4-3

Click Add to add a new entry, you can configure the parameters for PTM and WAN Service in the

next screen (shown in Figure 4-4).

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-4

DSL Modulation Type:

 DSL Modulation Type: The modem router supports two modulation types: ADSL and VDSL, you can select the corresponding types according to your needs.

PTM Configuration:

 Enable VLAN ID: Check the box to enable the Virtual LAN ID.

 VLAN ID (1~4049): This indicates the VLAN group, and the valid range is from 1 to 4049.

1) Static IP

Select this option if your ISP provides static IP information to you. You should set static IP address,

IP subnet mask, and gateway address in the screen below.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-5

WAN Service Setup:



Enable IPv4：Check the box to enable IPv4.

IP Address: Enter the IP address in dotted-decimal notation provided by your ISP.

Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.



Gateway (Optional): Enter the gateway IP address in dotted-decimal notation provided by your ISP.

 DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually.

The Route will use this DNS Server for priority.

 Default Gateway: Select a WAN Interface from the drop-down list as the IPv4 default gateway.

 Enable IPv6: Check the box to enable IPv6.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

 IPv6 Address: Enter the IPv6 address provided by your ISP.

 Prefix Length: Enter the prefix length of the IPv6 address. The default value is 64.

 IPv6 Gateway: Enter the gateway IPv6 address provided by your ISP.

 IPv6 DNS Server / Secondary IPv6 DNS Server: Here you can set IPv6 DNS Server (at least one) manually. The Route will use this IPv6 DNS Server for priority.

 IPv6 Default Gateway: Select a WAN Interface from the drop-down list as the IPv6 default gateway.

Click Advance, advanced selections of WAN Service Setup can be shown.

 MTU (Bytes): Maximum Transmission Unit Size. Check this box then you can change the

MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.

 Enable NAT: This technology translates the IP addresses of a local area network to a different IP address for the Internet. If this modem router is hosting your network’s connection to the Internet, please select the check box. If another Router exists in your network, you don’t need to select the option.

 Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act.

 Enable SPI Firewall: A SPI firewall enhances network’s security. Select the option to use a firewall, or else without a firewall.

 Enable IGMP Proxy: IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router. The default value is disabled, and if you are not sure, please contact your ISP or just leave it.

Click the Save button to save the settings.

2) Dynamic IP

Select this option, the modem router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-6

Click Advance, advanced selections for WAN Service Setup can be shown.

 MTU (Bytes): Maximum Transmission Unit Size. Check this box then you can change the

MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.

 Enable NAT: This technology translates the IP addresses of a local area network to a different

IP address for the Internet. If this modem router is hosting your network’s connection to the

Internet, please select the check box. If another Router exists in your network, you don’t need to select the option.

 Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act.

 Enable SPI Firewall: A SPI firewall enhances network’s security. Select the option to use a firewall, or else without a firewall.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

 Get IP with Unicast: This is disabled by default. The minority of DHCP Server of ISP will not support to enable this. When the Route is connected right but IP cannot get, you can select this box.

 Set DNS Server manually: Choose “Set DNS Server manually”, you can set DNS Server manually here. The modem router will use this DNS Server for priority.

 Get IPv6 Address with Unicast: This is disabled by default. The minority of DHCPv6 Server of ISP will not support to enable this. When the modem router is connected right but cannot get IPv6 address, you can select this box.

 Set IPv6 DNS Server manually: Choose “Set IPv6 DNS Server manually”, you can set IPv6

DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.

 Host Name: Here displays model No. of your modem router.

Click the Save button to save the settings.

3) PPPoE

If your ISP provides a PPPoE connection and you need to use an ATM Interface, choose PPPoE in the drop-down list, and then the screen will be displayed as below.

Figure 4-7

 PPP Username/Password/Confirm password: Enter the User Name, Password and

Confirm password provided by your ISP. These fields are case-sensitive.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

 Connection Mode: For PPPoE connection, you can select Always on or Connect on

demand or Connect manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time, the connection will drop down automatically.

And once there is traffic send or receive, the connection will be automatically on.

 Authentication Type: Select the Authentication Type from the drop-down list, the default method is AUTO_AUTH, and you can leave it as a default setting.

 Enable IPv4: Check this box to enable IPv4.

 Enable IPv6: Check this box to enable IPv6.

 Default Gateway: Select a WAN connection from the drop-down list as the IPv4 default gateway.

 IPv6 Default Gateway: Select a WAN connection from the drop-down list as the IPv6 default gateway.

Click Advance, advanced selections for WAN Service Setup can be shown.

 Service Name/Server Name: Enter the Service Name and Server Name if it was provided by your ISP. You can leave them blank, if the ISP doesn’t provide them.

 MTU (Bytes): Maximum Transmission Unit Size. Check this box then you can change the

MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.

 Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act.

 Enable SPI Firewall: A SPI firewall enhances network’s security. Select the option to use a firewall, or else without a firewall.

 Use IP address specified by ISP: Choose “Use IP address specified by ISP”, you can enter the IP address provided by your ISP.

 Set DNS Server manually: Choose “Set DNS Server manually”, you can set DNS Server manually here. The modem router will use this DNS Server for priority.

 Use IPv6 address specified by ISP: Choose “Use IPv6 address specified by ISP”, you can enter the IPv6 address provided by your ISP.

 Set IPv6 DNS Server manually: Choose “Set IPv6 DNS Server manually”, you can set IPv6

DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.

Click the Save button to save the settings.

4) Bridge

If you select this type of connection, the modem router can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-8

 Note:

After you finishing the Internet configuration, please click Save to make the settings take effect.

4.5.1.2 ADSL WAN Settings

For ADSL mode, there are six different configurations for the connection types, which are Static IP,

Dynamic IP, PPPoE, PPPoA, IPoA and Bridge. You can select the corresponding types according to your needs.

Figure 4-9

Click Add to add a new entry, you can configure the parameters for PTM and WAN Service in the

next screen (shown in Figure 4-10).

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-10

DSL Modulation Type:

 DSL Modulation Type: The modem router supports two modulation types: ADSL and VDSL, you can select the corresponding types according to your needs.

ATM Configuration:

 VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP.

 VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. The valid range is from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP.

1) Static IP

Select this option if your ISP provides static IP information to you. You should set static IP address,

IP subnet mask, and gateway address in the screen below.

TD-W9970 300Mbps Wireless N USB VDSL/ADSL Modem Router User Guide

Figure 4-11

Click Advance, advanced selections of ATM Configuration can be shown.

 Encapsulation Mode: Select the encapsulation mode for the Static IP Address. Here you can leave it default.

 ATM Qos Type: Select ATM Qos Type provided by ISP, and the type is UBR by default.