Coleman | 5070 Series | Instruction manual | Coleman 5070 Series Instruction manual

Coleman 5070 Series Instruction manual
FRENCH
ENGLISH
PROPANE
FORCED-AIR
HEATERS
INSTRUCTIONS FOR USE
SPANISH
IMPORTANT
Read this manual carefully before assembling, using or servicing this
heater. Keep this manual for future reference. If you have questions about
assembly, operation, servicing or repair of this heater, please call Coleman
at 1-800-835-3278 or TDD: 316-832-8707. In Canada call 1 800 387-6161.
Models: 5070 and 5075 Series
This product is designed and approved for use as an
indoor construction heater in accordance with ANSI
and CSA standards. It is intended for temporary
heating of unoccupied buildings under construction,
alteration or repair. It is not intended for home or
recreational use.
©2006 The Coleman Company, Inc.
CERTIFIED
®
ANSI Z83.7-CSA 2.14 - (2000)
CONSTRUCTION HEATER
®
GENERAL
SAFETY
INFORMATION
This manual contains important information about the assembly, operation and maintenance of this construction heater. General safety information is presented in these first few
pages and is also located throughout the manual. Particular attention should be paid to
information accompanied by the safety alert symbol “ WARNING”.
Keep this manual for future reference and to educate new users of this product. This manual
should be read in conjunction with the labeling on the product.
GENERAL HAZARD WARNING:
FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS
PROVIDED WITH THIS HEATER CAN RESULT IN DEATH, SERIOUS
BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZARDS
OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE
POISONING, AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE
INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN
INSTRUCTION MANUAL, LABELS, ETC., CONTACT THE MANUFACTURER.
WARNING: FIRE, BURN, INHALATION, AND EXPLOSION HAZARD.
KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER
OR CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS
RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE HEATER IN
SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT
THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.
WARNING
NOT FOR HOME OR RECREATIONAL VEHICLE USE.
This product is designed and approved for use as an indoor construction heater in accordance
with standard ANSI Z83.7 - CSA 2.14 - (2000).
We cannot foresee every use which may be made of our heaters. Check with your local fire
safety authority if you have questions about heater use.
Other standards govern the use of fuel gases and heat producing products for specific uses.
Your local authorities can advise you about these.
This indoor construction heater should not be used in areas directly exposed to water spray,
rain, and/or dripping water.
CARBON MONOXIDE POISONING:
This construction heater is a combustion appliance. All combustion appliances
produce carbon monoxide (CO) during the combustion process. This product is designed to
produce extremely minute, non-hazardous amounts of CO if used and maintained in
accordance with all warnings and instructions. Do not block air flow into or out of the
heater.
Early signs of carbon monoxide poisoning may resemble the flu with headaches,
dizziness and/or nausea. If these symptoms are present during operation of this product get
fresh air immediately!
Safety Information continues on next page
2
MAKE SURE ADEQUATE VENTILATION IS PROVIDED. Provide a fresh
outside air opening at least three (3) square feet (0.3 m2) or its equivalent, i.e., 1' x 3' (0.3 m
x 0.9 m) for each heating unit. DO NOT USE THIS HEATER IN LIVING QUARTERS
OR WHILE SLEEPING! California lists carbon monoxide as a reproductive toxin under
Proposition 65.
GENERAL
SAFETY
INFORMATION
Continued
ENGLISH
PROPANE GAS:
This product is fueled by propane gas. Propane gas is invisible, odorless, and
flammable. An odorant is normally added to help detect leaks and can be described as a
“rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable
by smell alone.
Propane gas is heavier than air and leaking propane will sink to the lowest level
possible. It can be ignited by ignition sources including matches, lighters, sparks or open
flames of any kind many feet away from the original leak. Use only propane gas set up for
vapor withdrawal.
Propane gas should be stored and used in compliance with local ordinances and
codes or with ANSI/NFPA 58. Turn off propane when not in use.
FIRE/EXPLOSION:
During operation, this product can be a source of ignition. Keep heater area clear
and free from combustible materials, gasoline, paint thinner, cleaning solvents and other
flammable vapors and liquids. Do not use heater in areas with high dust content.
MINIMUM HEATER CLEARANCES FROM COMBUSTIBLE MATERIALS: TWO
(2) FEET (0.6 M) FROM SIDES AND REAR, FOUR (4) FEET (1.2 M) FROM TOP,
AND SIX (6) FEET (1.8) FROM THE OUTLET. Keep heater at least six (6) feet (1.8 m)
away from propane tanks and keep propane hoses away from outlet opening of the heater.
ADDITIONAL SAFETY INFORMATION:
• Never alter or modify heater, propane hose/regulator assembly or propane cylinders.
Do not attach duct work of any kind to this heater.
• Always inspect heater, propane hoses and propane cylinders before use. Do not use
if leaking propane or if damaged. Replace hoses that have excessive wear, abrasion
or cuts. Use only Coleman repair parts and Coleman propane hoses and regulator
assemblies.
• KEEP OUT OF REACH OF CHILDREN.
• Heater will remain hot up to thirty (30) minutes after being turned off.
• Operate heater only on level, stable surface.
• Use only the electrical voltage and frequency specified on product decal.
• Electrical grounding instructions — this heater is equipped with a three-prong
(grounding) plug for your protection against shock hazard and should be plugged
directly into a properly grounded three-prong receptacle.
• Use only a three-prong, grounded extension cord.
• Make sure heater is plugged into outlet before igniting heater.
• Keep the appliance area clear and free from combustible materials, gasoline and
other flammable vapors and liquids.
• Do not block or obstruct the flow of combustion and ventilation air.
• Blower (forced air) and radiant type heaters must not be directed toward any
propane-gas container within 20 feet (6 m).
3
CONTENTS
SECTION
PAGE
General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . 2,3
Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Propane Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 6
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 – 9
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Preventative Maintenance Schedule. . . . . . . . . . . . . . . . . . . 11
Service Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Technical and Repair Service . . . . . . . . . . . . . . . . . . . . . . 44
PRODUCT
IDENTIFICATION
Piezo Ignitor
Button
Top Shell
POL Fitting
Propane
Hose/Regulator
Assembly
Figure 1 - 40,000 BTU/Hr. Model
Automatic
Valve Button
Burner Valve
Knob
Inlet
Connection
Figure 2 - 50,000 to 80,000 BTU/Hr. Model
Product Identification
4
UNPACKING
The Fuel System: The hose/regulator assembly attaches to the propane gas supply. The
propane gas moves through the thermoelectric valve and out the nozzle.
The Air System: The motor turns the fan. The fan pushes air into and around the combustion chamber. This air is heated and provides a stream of clean, hot air.
The Ignition System: The piezo spark ignitor (Model 5070A) or Electronic Module
(Model 5075A) sends voltage to the electrode. The spark at the electrode ignites the fuel
air mixture.
The Safety Control System: This system causes the heater to shut down if the heater
overheats for any reason including loss of electric power. (The fan will continue to operate
if electric power is not lost.)
THEORY OF
OPERATION
Fan
Combustion Chamber
Air For Heating
Motor
Combustion Air
Fuel
Cool Air In (Back)
Power Cord
Clean Heated Air
Out (Front)
Ignitor
Hose/Regulator
Assembly
Electrode
Cross Section Operational View (5070A Model Shown)
Propane gas and propane tank(s) are to be furnished by the user.
Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the
Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58. Your local
library or fire department will have this booklet.
PROPANE
SUPPLY
The amount of propane gas ready for use from propane tanks varies. Two factors decide
this amount:
1. The amount of propane gas in tank(s).
2. The temperature of tank(s)
Propane Supply Information continues on next page
5
ENGLISH
1. Remove all packing items applied to heater for shipment. Keep plastic cover caps
(attached to inlet connection and hose/regulator assembly) for storage.
2. Remove all items from carton.
3. Check all items for shipping damage. If heater is damaged, promptly inform dealer
where you bought heater.
PROPANE
SUPPLY
Continued
The chart below shows the minimum number of 20-pound or larger tanks needed to run
these heaters at the temperature indicated for at least 10 hours. Do not operate them with
tanks smaller than indicated. Reduced performance will result.
NUMBER OF TANKS REQUIRED
Average Temperature (°F)
At Tank Location
5070A751 (40,000 BTU/Hr.)
5075A751 (80,000 BTU/Hr.)
32°
(0°C)
20°
(-7°C)
10°
(-12°C)
0°
(-18°C)
-10°
(-23°C)
1-20#
1-100#
1-40#
2-100#
1-100#
2-100#
2-100#
3-100#
3-100#
3-100#
Less gas is vaporized at lower temperatures. You may need two or more 100-pound tanks
or one larger tank in colder weather. Your local propane gas dealer will help you select the
proper supply system.
WARNING
VENTILATION
Provide at least a 3-square-foot (0.3 m2) opening of fresh, outside air while
running heater. If proper outside air ventilation is not provided, carbon
monoxide poisoning can occur. Provide proper outside air ventilation before
running heater.
WARNING
PREPARATION
Test all gas piping and connections for leaks after preparation or servicing.
Never use an open flame to check for a leak. Apply a mixture of liquid soap
and water to all joints. Bubbles forming show a leak. Correct all leaks before
using product.
1. Determine propane supply needed. (See Propane Supply).
2. Connect hose to inlet connector. Tighten firmly in clockwise direction using 9/16" wrench.
Hose and Inlet Connector
Tighten with Wrench
Continued
6
PREPARATION
Continued
ENGLISH
3. Connect POL fitting on hose/regulator assembly to propane tank(s).
Turn POL fitting counterclockwise into threads on tank. Tighten firmly.
IMPORTANT: Tighten regulator with vent pointing down. Pointing vent down protects
regulator from weather damage.
Regulator With Vent Pointing Down
4. Open valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check
valve on propane tank will stop gas flow. If this happens, close propane valve and open
again slowly.
5. Check all connections for leaks. Apply mixture of liquid soap and water to gas joints.
Bubbles forming show a leak that must be corrected before using heater.
6. Close propane supply valve.
WARNING
OPERATION
Review and understand the warnings in the General Safety Information
Section. They are needed to safely operate this heater. Follow all local ordinances or codes when using this heater.
To Start Heater
1. Follow all preparation, ventilation, and safety information.
2. Locate heater on stable and level surface. Make sure strong drafts do not blow into front
or rear of heater. Do not use in areas directly exposed to water spray, rain, and/or dripping
water.
3. Open valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check valve
on propane tank will stop gas flow. If this happens, close propane valve and open again
slowly.
Continued
7
OPERATION
Continued
4. Plug power cord of heater into a three-prong, grounded extension cord. Extension cord must
be at least six feet long. Extension cord must be UL listed.
Extension Cord Size Requirement
Up to 50 feet (15 m) long, use 18 AWG rated cord.
51 to 100 feet (30 m) long, use 16 AWG rated cord.
101 to 200 (61 m) feet long, use 14 AWG rated cord.
5. Plug extension cord into a 120 volt/60 hertz, three-hole, grounded outlet. The motor will
start, turning the fan forcing air through the heater.
6. To light:
Model 5070A
Push in and hold automatic valve button. Push ignitor (Red) button. You may need to push
the ignitor button 3 – 8 times until heater lights. Note: Hose may be filled with air. If so,
keep automatic valve button pressed and wait 20 seconds before pressing ignitor again.
When heater lights, keep automatic valve button pushed in. Release button after
30 seconds.
Model 5075A
Push in & hold automatic valve button. NOTE: Hose may be filled with air. If so, continue
to keep automatic valve button pressed. When heater lights, keep automatic valve button
pushed in. Release button after 30 seconds.
5070 A751 Model Shown
7. If heater goes out, repeat step 6.
8. Adjust burner valve to desired heat level. (5075A751 Model only)
Continued
8
To Stop Heater
OPERATION
Continued
ENGLISH
1. Tightly close valve on propane tank(s).
2. Wait a few seconds. Heater will burn gas left in hose.
3. Unplug heater.
WARNING
STORAGE
Disconnect heater from propane supply tank(s) before storage.
1. Store propane tank(s) in safe manner. See Chapter 5 of Standard for Storage and
Handling of Liquefied Petroleum Gases, ANSI/NFPA 58. Follow all local codes.
2. Place plastic cover caps over brass fittings on inlet connection and hose/regulator
assembly of heater.
3. Store heater in a dry, clean, and safe place.
WARNING
MAINTENANCE
Never attempt to service heater while it is plugged in, connected to propane
supply, operating or hot. Severe burns and electrical shock can occur.
1. Keep heater clean. Clean heater annually or as needed to remove dust and debris. If
heater is dirty or dusty, clean heater with a damp cloth.
2. Inspect heater before each use. Check connections for leaks. Apply mixture of liquid
soap and water to connections. Bubbles forming show a leak. Correct all leaks before
using heater.
3. Inspect propane hose/regulator assembly before each use. Replace hoses that have
excessive wear, abrasion, or cuts. Inspect “O” ring for damage. Replace if cut or
cracked.
4. Have heater inspected yearly by a qualified service person.
5. Keep inside of heater free from combustible and foreign objects.
Continued
9
MAINTENANCE
Continued
6. FAN - Clean every 500 hours of operation or as needed.
A. Remove screws along each side of heater and on top of the motor guard using
a Phillips screwdriver. These screws attach top and lower shells together.
B. Lift top shell off.
C. Lift out motor/guard assembly.
IMPORTANT: Do not allow the motor/guard assembly to rest on the fan or damage may be
caused to the blades.
D. Clean fan using soft cloth moistened with kerosene or solvent. Dry fan
thoroughly. Clean inside the shell adjacent to where the fan runs.
E. Replace motor/guard assembly and top shell.
7. ELECTRODE
A. Make sure gap between electrode wire and burner nozzle is .20 (0.5 cm) to
.25" (0.6 cm). Access electrode from inside combustion chamber. No other
maintenance is needed for electrode.
Continued
10
Never attempt to service heater while it is plugged in, connected to propane
supply, operating or hot. Severe burns and electrical shock can occur.
SYMPTOM
POSSIBLE CAUSE
REMEDY
Fan does not turn
when heater is
plugged in.
No electrical power to heater
Check voltage to electrical outlet.
If voltage is good, check heater
power cord for breaks.
Fan blades bent
Replace fan. See Replacing Fan,
Page 13.
Defective motor
Replace motor. See Replacing Motor,
page 12.
User did not follow preparation or operation instructions properly
Repeat preparation and operation instructions. See Preparation,
pages 6 & 7 and Operation, pages 7,
8 & 9.
Heater will not
ignite.
No spark at electrode. To test
for spark, follow step 9 under Replacing Electrode,
page 13. If you see spark at
ignitor, have heater serviced
by qualified service person.
If no spark seen:
A) Loose or disconnected
ignitor wire
E) Bad piezo ignitor
A) Check ignitor wire. Tighten
or reattach loose ignitor wire.
See page 5 for ignitor
wire location.
B) Set gap between ignitor electrode
and target plate to .20" (0.5 cm).
C) Tighten piezo ignitor to base
of heater.
D) Replace electrode. See Replacing
Electrode, page 13.
E) Replace ignitor.
F) Bad electronic module
F) Replace electronic module.
High surrounding air temperature causing thermal
limit device to shut down
heater.
This can happen when running
heater in temperatures above
85°F (29°C). Run heater in cooler
temperatures.
Restricted air flow
Check heater inlet and outlet.
Remove any obstructions.
B) Wrong spark gap
C) Piezo ignitor loose
D) Bad electrode
Heater shuts down
while running.
WARNING
Damaged fan
Use only in areas
free of high dust
content.
Replace fan. See Replacing Fan,
page 13.
Excessive dust or debris in
surrounding area
Clean heater. See Maintenance,
pages 9 & 10.
ITEM
HOW OFTEN
HOW TO
Fan
Clean every 500 hours of
operation or as needed.
See Fan, page 10
Electrode
Clean and regap every 500
hours of operation or replace
as needed.
See Electrode, page 10
TROUBLESHOOTING
ENGLISH
WARNING
PREVENTIVE
MAINTENANCE
SCHEDULE
Continued
11
SERVICE
PROCEDURES
WARNING
Never attempt to service heater while it is plugged in, connected to propane
supply, operating, or hot. Severe burns and electrical shock can occur.
REPLACING MOTOR
1. Remove top shell (see FAN under maintenance).
2. Lift out motor/guard assembly.
3. Use a 1/8" hex wrench to loosen setscrew which holds fan to motor shaft.
4. Remove fan from motor shaft (it may be necessary to pry the fan from the shaft) being
careful not to damage the blades.
5. Remove the ground wire screw and two wire leads from the motor.
6. Remove two nuts and two screws which attach the motor to the guard.
7. Discard motor.
8. Attach new motor to guard using two screws and nuts.
9. Replace fan on shaft with approx. 3/8" (1 cm) of shaft showing through fan hub.
10. Tighten setscrew firmly (40-50 inch pounds).
11. Install ground wire and wire leads to motor.
12. Set motor/guard assembly in the lower shell. Turn fan to check for interference.
13. Install the top shell.
Continued
12
REPLACING FAN
1. Remove motor/guard assembly (follow steps 1 through 4 above).
2. File the setscrew mark off the motor shaft.
3. Replace fan (follow steps 9 through 13 above).
SERVICE
PROCEDURES
Continued
ENGLISH
REPLACING ELECTRODE
1. Remove shell and motor/guard assembly (see FAN under maintenance).
2. Pull wire off of electrode.
3. Remove screw holding electrode to diffuser.
4. Remove electrode from diffuser.
5. Place new electrode in diffuser.
6. Install screw, insure electrode gap is .20 (0.5 cm) to .25 (0.6 cm) inch.
7. Push ignitor wire on electrode wire.
8. Reinstall motor/guard assembly and upper shell.
9. For Model 5070A, push ignitor button and check for spark between deflector and electrode. For Model 5075A check for sparks between deflector & electrode after
plugging in. Do not connect propane supply.
SPECIFICATIONS
FORCED AIR HEATER SPECIFICATIONS
40,000 BTU/HR - MODEL 5070A
FORCED AIR HEATER SPECIFICATIONS
50,000 TO 80,000 BTU/HR - MODEL 5075A
Input Rating (BTU/HR)
40,000
Fuel
Propane Vapor Only
Fuel Consumption
Gallons/Hour
.44 (1.7 L)
Pounds/Hour
1.8 (0.8 kg)
Regulator Output Pressure
10 PSI (70 kPa)
Hose
10 Ft. (3 m)
Hot Air Output (CFM Approx.)
150
Motor
3,000 RPM
Power Required
115 Volt/60 Hz
Amps
1.1
Ignition
Manual/Piezo
Weight (pounds)
14 (6.4 kg)
Size (HWL) (IN)
14 x 8.5 x 16.5
(35.6 x 21.6 x 41.9 cm)
Temperature Operating Range -10°F to 85°F
(-23° to 29.4°C)
Input Rating (BTU/HR)
80,000 Max
Fuel
Propane Vapor Only
Fuel Consumption
Gallons/Hour
.9 (3.4 L)
Pounds/Hour
3.7 (1.7 kg)
Regulator Output Pressure
10 PSI (70 kPa)
Hose
10 Ft. (3 m)
Hot Air Output (CFM Approx.)
300
Motor
3,000 RPM
Power Required
115 Volt/60 Hz
Amps
2.6
Ignition
Electronic Module
Weight (pounds)
17 (7.7 kg)
Size (HWL) (IN)
14 x 8.5 x 22.5
(35.6 x 21.6 x 57.2 cm)
Temperature Operating Range -10°F to 85°F
(-23° to 29.4°C)
Continued
13
WIRING
DIAGRAM
THERMAL
SAFETY
SWITCH
THERMAL
SAFETY
SWITCH
T.E.
VALVE
T.E.
VALVE
PIEZO
IGNITOR
MOTOR
BLACK
WHITE
GREEN
MODEL 5075A
MODEL 5070A
REPLACEMENT
PARTS
WARNING
Use only original replacement parts. Do not substitute or use generic parts.
Improper replacement parts could cause serious or fatal injuries.
I.D.
NO.
PART NO.
DESCRIPTION
1
2
8
9
10
11
5070-2851
5070-2801
5075-2801
5070-2891
5075-2891
5070-3111
5070-3271
5075-3271
5070-2001
5070-2181
5075-2181
5080-5651
5080-1491
5410A1381
5075B3001
12
5070A2701
Guard & Pigtail Assembly
Motor (5070A Model)
Motor (5075A Model)
Fan Blade for Heater (5070A Model)
Fan Blade for Heater (5075A Model)
Electronic Ignition Assembly (5070A Model)
Thermocouple & Clip
Thermocouple, Clip & Spacer
Handle & Screws
Gas Tip (5070A Model)
Gas Tip (5075A Model)
Hose & Regulator
Knob & Screw (5075A Model)
O-ring
E.I. Module Assembly*
(5075A Model)
Thermostat
3
4
5
6
7
* Used on heaters manufactured after August 2002.
14
TECHNICAL
SERVICE
ASSISTANCE
À LA
CLIENTÈLE
SERVICIO
TÉCNICO
If you have questions, contact Coleman at: 1-800-835-3278 or TDD: 316-832-8707.
In Canada call 1 800 387-6161.
Des questions? Entrez en rapport avec Coleman en composant le 1 800 835-3278 ou le
316-832-8707 aux États-Unis, ou bien le 1 800 387-6161 au Canada.
Si tiene alguna duda, comuníquese con Coleman al 1-800-835-3278 o a la línea para personas con dificultad auditiva 316-832-8707. En Canadá llame al 1 800 387-6161.
© 2006 The Coleman Company, Inc. All rights reserved. Coleman® and
are registered trademarks of The Coleman Company, Inc.
© 2006 The Coleman Company, Inc. Tous droits réservés. Coleman® et
sont des marques déposées de The Coleman Company, Inc.
®
®
© 2006 The Coleman Company, Inc. Todos los derechos reservados. Coleman® y
son marcas registradas de The Coleman Company, Inc.
®
www.coleman.com
The Coleman Company, Inc.
3600 N. Hydraulic
Wichita, KS 67219 U.S.A.
1-800-835-3278
TDD: 316-832-8707
Sunbeam Corporation (Canada) Limited
DBA Jarden Consumer Solutions
5975 Falbourne Street
Mississauga, Ontario
CANADA L5R 3V8
1 800 387-6161
5070D050 (1/16/2006)
44
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising