Biostar | P4M890-M7 FE - QUICK | User`s manual | Biostar P4M890-M7 FE - QUICK User`s manual

Biostar P4M890-M7 FE - QUICK User`s manual
P4M890-M7 SE Setup Manual
FCC Information and Copyright
This equipment has been tes ted and found to comply with the limits of a Class
B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed
to provide reasonable protec tion against harmful interference in a residential
installation. T his equipment generates , uses and can radiate radio frequency
energy and, if not ins talled and used in accordance with the instructions , may
cause harmful interference to radio communications . There is no guarantee
that interference will not occur in a particular ins tallation.
The vendor makes no representations or warranties with respec t to the
contents here and s pecially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make c hanges to the c ontents here without obligation to
notify any party beforehand.
D uplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be c hanged without notice and
we will not be res ponsible for any mis takes found in this user’s manual. All the
brand and produc t names are trademarks of their respec tive companies .
Table of Contents
Chapter 1: Introduction ............................................. 3
1.1
1.2
1.3
1.4
1.5
Before You Start................................................................... 3
Package Checklist................................................................ 3
Motherboard Features.......................................................... 4
Rear Panel Connectors.......................................................... 5
Motherboard Layout ............................................................ 6
Chapter 2: Hardware Installation.............................. 7
2.1
2.2
2.3
2.4
Installing Central Processing Unit (CPU) ................................ 7
FAN Headers........................................................................ 9
Installing System Memory.....................................................10
Connectors and Slots ............................................................11
Chapter 3: Headers & Jumpers Setup ......................13
3.1
3.2
How to Setup Jumpers..........................................................13
Detail Settings.....................................................................13
Chapter 4: Useful Help ..............................................18
4.1
4.2
4.3
4.4
Driver Installation Note .......................................................18
AWARD BIOS Beep Code......................................................19
Extra Information................................................................19
Troubleshooting...................................................................21
Chapter 5: WarpSpeeder™ .......................................22
5.1
5.2
5.3
5.4
Introduction........................................................................22
System Requirement............................................................22
Installation .........................................................................23
WarpSpeeder™....................................................................24
Appendencies: SPEC In Other Language ................30
German................................................................................................30
France..................................................................................................32
Italian..................................................................................................34
Spanish ................................................................................................36
Portuguese...........................................................................................38
Polish...................................................................................................40
Russian ................................................................................................42
Arabic..................................................................................................44
Japanese ..............................................................................................46
P4M890-M7 SE
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU ST ART
Thank you for choosing our product. Be fore you start installing the
mothe rboard, please make sure you follow the instructions be low:
„ Prepare a dry and stable work ing environment with
sufficie nt lighting.
„ Always disconne ct the compute r from powe r outle t
be fore ope ration.
„ Before you take the mothe rboard out from anti-static
bag, ground yourse lf prope rly by touching any safe ly
grounde d appliance, or use grounded wrist strap to
remove the static charge.
„ Avoid touching the compone nts on mothe rboard or the
rear side of the board unless ne cessary. Hold the board
on the edge , do not try to be nd or flex the board.
„ Do not leave any unfastene d small parts inside the
case afte r installation. Loose parts will cause short
circuits which may damage the equipment.
„
Keep the compute r from dange rous a rea, such as hea t
source , humid air and wate r.
1.2
PACKAGE CHECKLIST
z
z
z
HDD Cable X 1
Use r’s Manual X 1
Fully Se tup Drive r C D X 1
z
z
z
z
z
z
Rear I/O Panel for ATX Case X 1
FDD Cable X 1 (optional)
Se rial ATA Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF Cable X 1 (optional)
Se rial ATA Powe r Cable X 1 (optional)
3
Motherboard Manual
1.3
MOT HERBOARD FEAT URES
SPEC
LGA 775
Intel Core 2Duo/ Pe ntium 4 / Pe ntium D / Supports Hy per Tra nsport/ Execute Disable
CPU
Celeron D pr ocessor up to 3.8 GHz
Bit/ Enhanced Intel S peedStep®/ Intel
*It is recommende d to use processors
Extende d Memor y 64 technolo gy
with 95W power consumption.
FSB
Chipset
Graphic
Super I/O
533 / 800 / 1066 MHz
VIA P4M890
VIA VT8237A
Integrated i n U niChrome Pro Chipset
Max Share d Vide o Memory is 64 MB
ITE IT8712F
Enviro nment Co ntrol initiatives,
Provides the most commonly used
H/W Monitor
legacy Super I/O functionality.
Fan Spee d Co ntroller
Low Pin C ount Interface
ITE's "Smart Guardia n" function
DIMM Slots x 2
Main
Memory
Supports DDR2 533
Single Channel Mode DDR2 memory mo dule
Each DIMM supports
Registered DIMM and ECC DIMM is not
256/512MB/1GB/2GB DDR2
supported
Max Memory C apicity 4GB
IDE
Integrated I DE Controller
SATA
Integrated Seri al ATA Controller
LAN PHY
Realtek RTL 8201CL PH Y
Sound
Codec
Ultra DMA 33~133 B us Master Mode
supports PIO Mo de 0~4,
Data transfer rates up to 1.5 Gb/s.
SATA Version 1.0 specification complia nt.
10 / 100 Mb/s auto negotiation
Half / Full duplex capability
5.1 cha nnels a udio o ut
ALC861VD
High- Defi nition Audio s upport
PCI Expr ess x 16 slot
x1
Supports PCI express x 16 expansion cards
PCI Expr ess x 1 slot
x1
Supports PCI express x 1 e xpa nsion cards
PCI slot
x2
Supports PCI expa nsion cards
On Board
Floppy connector
x1
Each connector supports 2 Flo ppy drives
Connector
IDE Co nnector
x2
Each connector supports 2 IDE device
SATA Connector
x2
Each connector supports 1 SATA devices
Front Pa nel Co nnector
x1
Supports front panel facilities
Front Audi o Co nnector
x1
Supports front panel a udio function
CD-in Co nnector
x1
Supports CD audio-in function
Slots
4
P4M890-M7 SE
SPEC
Back Panel
I/O
S/PDIF o ut co nnector
x1
CPU Fan hea der
x1
Supports di gital a udio out function
CPU Fan power s upply (with Smart Fa n
function)
System Fan hea der
x1
System Fan Power supply
Clear CMOS header
x1
Restore CMOS data to factory defa ult
USB connector
x2
Power Connector ( 24pi n)
x1
Connects to Power supply
Power Connector ( 4pin)
x1
Connects to Power supply
PS/2 Keyboard
x1
Connects to PS/ 2 Key board
PS/2 Mo use
x1
Connects to PS/ 2 Mo use
Serial Port
x1
Provide RS- 232 Serial connection
Printer Port
x1
Connects to vari ous types of device
VGA Port
x1
Connects to mo nitor.
LAN port
x1
Connects to RJ- 45 ether net cable
USB Port
x4
Connects to USB devices
Audio J ack
x3
Provide A udio-I n/Out a nd micropho ne
Each connector supports 2 fr ont panel USB
ports
connection
Board Size 190 mm (W) x 244 mm (L)
Micro ATX form Factor
OS
Biostar Reserves the right to a dd or r emove
Support
1.4
PS/2
Mouse
Windows 2000 / XP
support for any OS with or witho ut notice.
REAR PANEL CONNECT ORS
LAN
Printer Port
Li ne In/
Surround
Line Out
Mic In 1/
Bass/ Center
PS/2
Keyboard
COM1
VGA
USBX2
USBX2
5
Motherboard Manual
1.5
MOT HERBOARD LAYOUT
JCFAN1
J KBMS 1
LGA775
COM1
JCOM1
CPU1
JPRNT1
DIMM1
JVGA1
JUSB1
DIMM2
JATXPWR1
JUSBV1
IDE1
P4M890
JUSBLAN1
IDE2
JATXPWR2
LAN
J AUDIO1
PCI-EX16
Super
I/O
PCI-EX1_1
BAT1
JSATA2
JUSB2
VIA
VT8237A
PCI1
BIOS
JSATA1
JCDIN1
JUSB3
PCI2
JCMOS1
JSPDIF_OUT1
Codec
JAUDIOF1
Not e: ■ represe nts the 1st pin.
6
JUSBV2
FDD1
JSFAN1
JPANEL1
P4M890-M7 SE
CHAPTER 2: HARDWARE INSTALLATION
2.1 INST ALLING CENT RAL PROCESSING UNIT (CPU)
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.
Pin Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
7
Motherboard Manual
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:
Step 2-2:
Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.
8
P4M890-M7 SE
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Heade r
4
1
JCFAN1
Pin
1
2
3
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control
JSFAN1: System Fan He ader
Pin
JSFAN1
3
1
2
3
Assignment
Ground
+12V
FAN RPM rate
sense
1
Note:
The JSFAN1 s upport 3-pi n head connec tor. When c onnecti ng with wires onto connec tors,
pleas e note that the red wire is the positi ve and s hould be c onnected to pin#2, and the
blac k wire is Ground and s hould be c onnected to GND.
9
Motherboard Manual
2.3
INST ALLING SYST EM MEMORY
DIMM1
DIMM2
A. Memory Modules
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
B. Memory Capacity
10
DIMM Socket
Location
DIMM1
256MB/512MB/1GB/2GB
DIMM2
256MB/512MB/1GB/2GB
DDR Module
Total Memory
Size
Max is 4GB.
P4M890-M7 SE
2.4
CONNECT ORS AND SLOT S
FDD1: Floppy Disk Conne ctor
The motherboard prov ides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the
prov ided f loppy drive ribbon cables.
2
34
1
33
IDE1/IDE2: Hard Disk Conne ctors
The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 f unctionality. It has two
HDD connectors IDE1 (primary) and IDE2 (secondary).
The IDE connectors can connect a master and a slav e driv e, so you can
connect up to four hard disk drives. The f irst hard drive should always be
connected to IDE1.
40
39
2
1
IDE1
IDE2
11
Motherboard Manual
PCI-EX16: PCI-Express x16 Slot
-
PCI-Express 1.0a compliant.
-
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, f or an aggregate of 8GB/s totally.
PCI-EX1_1: PCI-Express x1 Slot
-
PCI-Express 1.0a compliant.
-
Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth ov er the traditional PCI architecture.
PCI-EX16
PCI-EX1_1
PCI1~PCI2: Pe riphe ral Component Interconne ct Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands f or
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
12
P4M890-M7 SE
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW T O SET UP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DET AIL SETT INGS
JPANEL1: Front Panel Heade r
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep
button and speaker connection. It allows user to connect the PC case’s f ront
panel switch functions.
SLP
PWR_LED
On/Off
++ -
9
1
+ SPK
Pin
1
2
3
4
5
6
7
8
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Functio n
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
16
8
RST
HLED
Assignment
Sleep control
Ground
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Functio n
Sleep button
N/A
Power LED
Power-on button
13
Motherboard Manual
ATX Powe r Source Conne ctor: JATXPWR1
JATXPWR1 allows user to connect 24-pin power connector on the ATX power
supply.
12
24
1
13
Pin
Assignment
Pin
Assignment
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
1
2
3
4
5
6
7
8
9
10
11
12
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
JATXPWR2: ATX Powe r Source Conne ctor
By connecting this connector, it will provide +12V to CPU power circuit.
14
1
4
2
3
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
P4M890-M7 SE
JUSB2/JUSB3: Heade rs for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC f ront panel,
and also can be connected with internal USB devices, like USB card reader.
2
10
JUSB2
1
9
JUSB3
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
JUSBV1/JUSBV2: Powe r Source Heade rs for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBV2: +5V for USB ports at f ront panel (JUSB2/JUSB3).
Pin 2-3 Close:
JUSBV1: USB ports at JUSB1/JUSBLAN1 are powered by +5V standby
v oltage.
JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V
standby v oltage.
1
1
3
3
Pin 1-2 close
JUSBV1
1
1
3
3
Pin 2-3 close
JUSBV2
Note:
In order to s upport this function “Power-On s ystem vi a USB devic e,” “JUSBV1/ JUSBV2”
jumper cap should be plac ed on Pin 2-3 indi viduall y.
15
Motherboard Manual
JAUDIO F1: Front Panel Audio Heade r
This header allows user to connect the front audio output cable with the PC f ront
panel. It will disable the output on back panel audio connectors.
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JCDIN1: CD-RO M Audio-in Connector
This connector allows user to connect the audio source f rom the v ariaty dev ices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.
Pin
1
2
3
4
4
Assignment
Left Channel Input
Ground
Ground
Right Channel Input
1
JSPDIF_O UT1: Digital Audio-out Conne ctor
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
1
2
3
3
16
1
Assignment
+5V
SPDIF_OUT
Ground
P4M890-M7 SE
JCMO S1: Cle ar CMOS Heade r
By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting
and the CMOS data, please carefully f ollow the procedures to avoid damaging
the motherboard.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
1
3
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Proce dures:
1.
2.
3.
4.
5.
6.
Remov e AC power line.
Set the jumper to “Pin 2-3 close”.
Wait f or f ive seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset y our desired password or clear the CMOS data.
JSATA1~JSATA2: Se rial ATA Connectors
The motherboard has a PCI to SATA Controller with 2 channels SATA interf ace,
it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.
7
4
1
JSATA2
JSATA1
1
4
Pin
1
2
3
4
5
6
7
Assignment
Ground
T X+
T XGround
RXRX+
Ground
7
17
Motherboard Manual
CHAPTER 4: USEFUL HELP
4.1
DRIVER INST ALLAT ION NOT E
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you ins ert the Driver CD, please use file brows er to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat R eader to open the manual file. Pleas e download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep 2.html
18
P4M890-M7 SE
4.2
AWARD BIOS BEEP CODE
Beep Sound
One long beep followed by two short
beeps
High-low siren sound
Meaning
Video card not found or v ideo card
memory bad
CPU overheated
System will shut down automatically
One Short beep when system boot-up No error found during POST
Long beeps every other second
4.3
No DRAM detected or install
EXT RA INFORMAT ION
A. BIOS Update
After you fail to update BIOS or BIOS is invaded by virus, the
Boot-Block function will help to restore BIOS. If the following message
is shown after boot-up the system, it means the BIOS contents are
corrupted.
In this Case, please follow the procedure below to restore the BIOS:
1. Make a bootable floppy disk.
2. Download the Flash Utility “AWDFLASH.exe” from the Biostar
website: www.biostar.com.tw
3. Confirm motherboard model and download the respectively BIOS
from Biostar website.
4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.
5. Insert the bootable disk into floppy drive and press Enter.
6. System will boot-up to DOS prompt.
7. Type “Awdflash xxxx.bf/sn/py/r” in DOS prompt.
(xxxx means BIOS name.)
8. System will update BIOS automatically and restart.
9. The BIOS has been recovered and will work properly.
19
Motherboard Manual
B. CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
20
P4M890-M7 SE
4.4
TROUBLESHOOT ING
Probable
Solution
1.
Make sure power cable is
No power to the system at all
securely plugged in.
Power light don’t illuminate, f an
inside power supply does not turn 2.
Replace cable.
on.
3.
Contact technical support.
2.
Indicator light on key board does
not turn on.
System inoperativ e. Keyboard lights
Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard driv e is spinning.
module snaps into place.
1.
System does not boot from hard disk
1.
driv e, can be booted f rom optical driv e.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the driv e type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
1.
Back up data and applications
System only boots f rom optical driv e.
f iles.
Hard disk can be read and applications
can be used but booting from hard disk 2.
Ref ormat the hard driv e.
is impossible.
Re-install applications and data
using backup disks.
Screen message says “Invalid
Rev iew system’s equipment. Make sure
Conf iguration” or “CMOS Failure.”
correct inf ormation is in setup.
Cannot boot system after installing
1.
Set master/slave jumpers
second hard driv e.
correctly.
2.
Run SETUP program and select
correct driv e types. Call the drive
manuf acturers f or compatibility
with other drives.
21
Motherboard Manual
CHAPTER 5: WARPSPEEDER™
5.1
INT RODUCT ION
[WarpSpeeder™], a new powerful control utility, features three
user-friendly functions including Overclock Manager, Overvoltage
Manager, and Hardware Monitor.
With the Overclock Manager, users can easily adjust the frequency they
prefer or they can get the best CPU performance with just one click. The
Overvoltage Manager, on the other hand, helps to power up CPU core
voltage and Memory voltage. The cool Hardware Monitor smartly indicates
the temperatures, voltage and CPU fan speed as well as the chipset
information. Also, in the About panel, you can get detail descriptions about
BIOS model and chipsets. In addition, the frequency status of CPU,
memory, AGP and PCI along with the CPU speed are synchronically
shown on our main panel.
Moreover, to protect users' computer systems if the setting is not
appropriate when testing and results in system fail or hang,
[WarpSpeeder™] technology assures the system stability by automatically
rebooting the computer and then restart to a speed that is either the
original system speed or a suitable one.
5.2
SYST EM REQUIREMENT
OS Support: Windows 98 SE, Windows Me, Windows 2000, Windows XP
DirectX: DirectX 8.1 or above. (The Windows XP operating system
includes DirectX 8.1. If you use Windows XP, you do not need to install
DirectX 8.1.)
22
P4M890-M7 SE
5.3
INST ALLAT ION
1. Execute the setup execution file, and then the following dialog will pop
up. Please click “Next” button and follow the default procedure to
install.
2. When you see the following dialog in setup procedure, it means setup
is completed. If the “Launch the WarpSpeeder Tray Utility” checkbox
is checked, the Tray Icon utility and [WarpSpeeder™] utility will be
automatically and immediately launched after you click “Finish”
button.
Usage :
The following figures are just only for reference, the screen printed in
this user manual will change according to your motherboard on hand.
23
Motherboard Manual
5.4
WARPSPEEDER™
1. Tray Icon:
Whenever the Tray Icon utility is launched, it will display a little tray
icon on the right side of Windows Taskbar.
This utility is responsible for conveniently invoking [WarpSpeeder™]
Utility. You can use the mouse by clicking the left button in order to
invoke [WarpSpeeder™] directly from the little tray icon or you can
right-click the little tray icon to pop up a popup menu as following
figure. The “Launch Utility” item in the popup menu has the same
function as mouse left-click on tray icon and “Exit” item will close
Tray Icon utility if selected.
24
P4M890-M7 SE
2. Main Panel
If you click the tray icon, [WarpSpeeder™] utility will be invoked.
Please refer to the following figure; the utility’s first window you will
see is Main Panel.
Main Panel contains fe ature s as follows:
a. Display the CPU Speed, CPU external clock, Memory clock, AGP clock,
and PCI clock information.
b. Contains About, Voltage, Overclock, and Hardware Monitor Buttons for
invoking respective panels.
c. With a user-friendly Status Animation, it can represent 3 overclock
percentage stages:
Man walking→overclock percentage from 100% ~ 110 %
Panther running→overclock percentage from 110% ~ 120%
Car racing→overclock percentage from 120% ~ above
25
Motherboard Manual
3. Voltage Panel
Click the Voltage button in Main Panel, the button will be highlighted
and the Voltage Panel will slide out to up as the following figure.
In this panel, you can decide to increase CPU core voltage and
Memory voltage or not. The default setting is “No”. If you want to get
the best performance of overclocking, we recommend you click the
option “Yes”.
26
P4M890-M7 SE
4. Overclock Panel
Click the Overclock button in Main Panel, the button will be
highlighted and the Overclock Panel will slide out to left as the
following figure.
O ve rclock Panel contains the these features:
a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz button”:
provide user the ability to do real-time overclock adjustment.
Warning:
Manually overclock is potentially dangerous, especially when the
ov erclocking percentage is over 110 %. We strongly recommend you
v erify ev ery speed you overclock by click the Verify button. Or, you can
just click Auto ov erclock button and let [WarpSpeeder™] automatically
gets the best result f or y ou.
b. “Recovery Dialog button”: Pop up the following dialog. Let user select
a restoring way if system need to do a fail-safe reboot.
27
Motherboard Manual
c.
d.
“Auto-overclock button”: User can click this button and
[WarpSpeeder™] will set the best and stable performance and
frequency automatically. [WarpSpeeder™] utility will execute a
series of testing until system fail. Then system will do fail-safe
reboot by using Watchdog function. After reboot, the
[WarpSpeeder™] utility will restore to the hardware default
setting or load the verified best and stable frequency according
to the Recovery Dialog’s setting.
“Verify button”: User can click this button and [WarpSpeeder™]
will proceed a testing for current frequency. If the testing is ok,
then the current frequency will be saved into system registry. If
the testing fail, system will do a fail-safe rebooting. After reboot,
the [WarpSpeeder™] utility will restore to the hardware default
setting or load the verified best and stable frequency according
to the Recovery Dialog’s setting.
Note:
Because the testing programs, invoked in Auto-overclock and Verify,
include DirectDraw, Direct3D and DirectShow tests, the DirectX 8.1 or
newer runtime library is required. And please make sure y our display
card’s color depth is High color (16 bit) or True color( 24/32 bit ) that is
required f or Direct3D rendering.
5. Hardware Monitor Panel
Click the Hardware Monitor button in Main Panel, the button will be
highlighted and the Hardware Monitor panel will slide out to left as
the following figure.
In this panel, you can get the real-time status information of your
system. The information will be refreshed every 1 second.
28
P4M890-M7 SE
6. About Panel
Click the “about” button in Main Panel, the button will be highlighted
and the About Panel will slide out to up as the following figure.
In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the mainboard’s BIOS model and the Version number of
[WarpSpeeder™] utility.
Note :
Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, [WarpSpeeder™] divide
these features to separate panels. If one chipset is not on board, the
correlative button in Main panel will be disabled, but will not interfere
other panels’ functions. This property can make [WarpSpeeder™]
utility more robust.
29
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
GERMAN
Spezifikationen
LGA 775
Intel Core2Duo/ Pe ntium 4 / Pe ntium D Unterstützt Hyper-Threa ding / Execute Disable
CPU
/ Celeron D Prozessoren mit bis zu 3,8 Bit / Enhance d I ntel Spee dStep® / Intel
GHz
Architecture-64 / Exte nde d Memory 64
*It is recommende d to use processors Technol ogy
with 95W power consumption.
FSB
Chipsatz
Grafik
Super E/A
533 / 800 / 1066 MHz
VIA P4M890
VIA VT8237A
Integrierter U niChrome Pro C hipsatz
Max. 64MB gemeinsam benutzter
Videospeicher
ITE 8712F
Umgebungskontrolle,
Bietet die häufi g verwe ndete n alte n
Hardware-Überwachung
Super E/A-Funktione n.
Lüfterdre hzahl-Co ntroller
Low Pin C ount-Schnittstelle
"Smart Guar dian" -Funktion v on ITE
DDR2 DIMM-Steckplätze x 2
Arbeitsspeic
her
Unterstützt DDR2 533
Ein-Kanal DDR2 S peichermodul
Jeder DIMM unterstützt
registrierte DIMMs. ECC DIMMs werde n nicht
256/512MB/1GB/2GB DDR2.
unterstützt.
Max. 4GB Ar beitsspeicher
Integrierter IDE-Co ntroller
IDE
Ultra DMA 33 / 66 / 100 / 133Bus
Unterstützt PIO-Modus 0~4,
Master-Modus
SATA
LAN PHY
Audio-Code
c
Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version
Datentransferr ate bis zu 1.5Gb/s
1.0.
10 / 100 Mb/s A uto-Negotiation
Realtek RTL 8201CL PH Y
Halb-/ Vollduplex- Funktion
Unterstützt High- Definitio n Audio
ALC861VD
5.1-Kanal-Audioausgabe
PCI-Steckplatz
x2
Steckplätze PCI Expr ess x16 Steckplatz
x1
PCI Expr ess x 1-Steckplatz
x1
30
P4M890-M7 SE
Spezifikationen
Onboard-An
schluss
Jeder A nschluss unterstützt 2
Diskettenlaufwerk anschluss
x1
IDE-Anschluss
x2
Jeder A nschluss unterstützt 2 IDE-L aufwerk e
SATA-Anschluss
x2
Jeder A nschluss unterstützt 1 SATA-Laufwerk
Fronttafela nschluss
x1
Unterstützt die Fro nttafelfunktio nen
Front-Audioa nschluss
x1
CD-IN-Anschluss
x1
Unterstützt die CD Audio-I n-Funktion
S/PDIF-Ausgangsanschluss
x1
Unterstützt die di gitale Audi oausgabe funktion
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x2
Diskettenlaufwerke
Unterstützt die
Fronttafel-Audioanschlussfunktio n
CPU-Lüfterstromversorgungsanschl uss (mit
Smart Fan-Funktion)
System-Lüfter-Stromversorgungsa nschluss
Jeder A nschluss unterstützt 2
Fronttafel-USB-Anschlüsse
Stromanschluss (24- polig)
x1
Stromanschluss (4-poli g)
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
Serieller Anschluss
x1
Rückseiten- Druckeranschluss
x1
E/A
VGA-Anschluss
x1
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
Platinengr ö
ße.
190 mm (B) X 244 mm (L)
Biostar behält sich das Recht v or, ohne
OS-Unterst
ützung
Windows 2K / XP
Ankündigung die Unterstützung für ei n
Betriebssystem hinzuzufügen oder zu
entfernen.
31
Motherboard Manual
FRANCE
SPEC
LGA 775
Processeurs Intel Core 2Duo/ P entium Prend en charge les technologies
UC
4 / Pe ntium D / Celer on D jusqu'à 3,8 Hyper -Thre ading / d'ex écution de bit de
désactivation / I ntel Spe edStep® optimisée/
GHz
*It is recommende d to use processors d'architecture Intel 64 / de mém oire éte ndue 64
with 95W power consumption.
Bus frontal 533 / 800 / 1066 MHz
Chipset
VIA P4M890
VIA VT8237A
Graphi que Integré dans l a chipset U niChrome
s
Pro
Initiatives de co ntrôle e nvironnementales,
ITE 8712F
Super E/S
Mémoire vidé o partagée maximale de 64 Mo
Fournit la fo nctionnalité de Super E/S Moniteur de matériel
Contrôleur de vitesse de ventilateur
patrimoniales la plus utilisée.
Interface à faible compte de broc hes Fonction " Gardie n i ntelligent" de l'ITE
Fentes DDR 2 DIMM x 2
Mémoire
principale
Module de mém oire DDR2 à mo de à simple v oie
Prend en charge la DDR 2 533
Chaque DIMM prend e n charge des
DDR2 de 256 Mo /512 Mo / 1Go / 2 Go
Capacité mémoire maximale de 4 Go
Les DIMM à r egistres et DIMM avec code
correcteurs d'erreurs ne so nt pas prises en
charge
Contrôleur IDE intégr é
IDE
Mode principale de Bus Ultra DMA 33 / Prend en charge le mode PIO 0~4,
66 / 100 / 133
SATA
LAN PHY
Codec
audio
Fentes
Connecteu
r
embarqué
32
Contrôleur Serial ATA intégré :
Taux de transfert jusqu'à 1.5 Go/s.
10 / 100 Mb/s négociation a utomatique
Realtek RTL 8201CL PH Y
Half / Full duplex capability
Prise en c harge de l'audio haute dé finition
ALC861VD
Sortie audio à 5.1 voies
Fente PCI
x2
Slot PCI Ex press x16
x1
Slot PCI Ex press x 1
x1
Connecteur de disquette
x1
Connecteur IDE
Conforme à la spécification SATA Version 1.0
x2
Chaque connector pre nd en charge 2 lecteurs de
disquettes
Chaque connecteur prend e n char ge 2
périphéri ques I DE
P4M890-M7 SE
SPEC
Connecteur SATA
x2
Connecteur du pa nne au avant
x1
Connecteur Audio du panneau
Chaque connecteur prend e n char ge 1
périphéri que SATA
Prend en charge les é quipements du panneau
avant
Prend en charge la fo nction a udio du panneau
avantx1
x1
avant
Connecteur d'entré e CD
x1
Prend en charge l a fonction d'entrée audio de CD
Connecteur de sortie S/PDIF
x1
Embase de ve ntilateur UC
x1
Embase de ve ntilateur système x1
Embase d'e ffacement CMOS
x1
Connecteur USB
x2
Connecteur d'alimentatio n
x1
Prend en charge la fo nction de sortie audio
numérique
Alimentation électrique du ve ntilateur UC (avec
fonction de ventilateur intellige nt)
Alimentation électrique du ve ntilateur système
Chaque connecteur prend e n char ge 2 ports USB
de panneau avant
(24 broches)
Connecteur d'alimentatio n
x1
(4 br oches)
E/S du
panneau
arrière
Clavier PS/2
x1
Souris PS/2
x1
Port série
x1
Port d'imprimante
x1
Port VGA
x1
Port LAN
x1
Port USB
x4
Fiche audio
x3
Dimension
s de la
190 mm (l) X 244 mm (H)
carte
Support
SE
Windows 2K / XP
Biostar se réserve le droit d'ajo uter o u de
supprimer le support de SE av ec ou sans préavis.
33
Motherboard Manual
IT ALIAN
SPECIFICA
LGA 775
Processore Intel Core 2Duo/ Pentium
CPU
4 / Pentium D / Celero n D fino a 3.8
GHz
*It is recommende d to use processors
Supporto di Hyper -Threadi ng / Execute Disable
Bit / Enhance d I ntel Spee dStep® / Architettura
Intel 64 / Tecnologia Exte nde d Memory 64
with 95W power consumption.
FSB
Chipset
Grafica
533 / 800 / 1066 MHz
VIA P4M890
VIA VT8237A
Integrata nel Chi pset UniC hrome Pr o La memoria vi deo co ndivisa massima è di 64MB
ITE 8712F
Super I/O
Funzioni di co ntrollo dell’ambiente:
Fornisce le funzio nalità legacy Super Monitoraggio hardware
I/O usate più comunemente.
Controller velocità ventolina
Interfaccia LPC (L ow Pin Count)
Funzione "Smart Guardi an" di I TE
Alloggi DIMM DDR 2 x 2
Memoria
principale
Supporto di DDR2 533
Ciascun DIMM supporta DDR 2 256MB
/512MB / 1GB / 2GB
Modulo di memoria DDR2 a canale singolo
DIMM registrati e DIMM ECC non sono supportati
Capacità massima della memoria 4GB
Controller IDE i ntegrato
IDE
Modalità Bus Master Ultra DMA 33 /
66 / 100
Supporto modalità PIO Mode 0- 4
/ 133
Controller Serial ATA inte grato
SATA
Velocità di trasferimento dei dati fi no Compatibile specifiche SATA Versione 1.0.
a 1.5 Gb/s.
LAN PHY
Codec
audio
34
Capacità Half / Full Duplex
Supporto audio High-Definition (HD)
ALC861VD
Alloggio PCI
Alloggi
Negoziazione automatica 10 / 100 Mb/s
Realtek RTL 8201CL PH Y
Uscita audio 5.1 canali
x2
Alloggio PCI Ex press x16
x1
Alloggio PCI Ex press x1
x1
P4M890-M7 SE
SPECIFICA
Connettore flo ppy
x1
Ciascun connettore supporta 2 unità Floppy
Connettore IDE
x2
Ciascun connettore supporta 2 unità IDE
Connettore SATA
x2
Ciascun connettore supporta 1 unità SATA
Connettore pa nnello fro ntale
x1
Supporta i servizi del pa nnell o fr ontale
Connettore audio frontale
x1
Supporta la funzione audi o pannello frontale
Connettore CD-in
x1
Supporta la funzione i nput audio C D
Connettore output SPDIF
x1
Supporta la funzione d’output a udio digitale
Connettori Collettore ventolina CPU
su scheda
x1
Collettore ventolina sistema
x1
Collettore cancellazione CMOS
x1
Connettore USB
x2
Connettore alimentazione
x1
Alimentazione v entolina C PU (con funzio ne Smart
Fan)
Alimentazione ve ntolina di sistema
Ciascun connettore supporta 2 porte USB
pannello frontale
(24 pin)
Connettore alimentazione
x1
(4 pi n)
I/O
pannello
posteriore
Dimension
i scheda
Tastiera PS/2
x1
Mouse PS/2
x1
Porta seriale
x1
Porta stampante
x1
Porta VGA
x1
Porta LAN
x1
Porta USB
x4
Connettore audio
x3
190 mm (larghezza) x 244 mm
(altezza)
Sistemi
operativi
supportati
Biostar si riserva il diritto di aggiungere o
Windows 2K / XP
rimuovere il supporto di qualsiasi sistema
operativo se nza pre avviso.
35
Motherboard Manual
SPANISH
Especificación
LGA 775
CPU
Procesador I ntel Core 2Duo/ P entium
Admite Hyper -Threadi ng / Bit de deshabilitación
4 / Pentium D / Celero n D hasta 3,8
de ejecució n / Intel SpeedStep® Me jorado / Intel
GHz
Architecture-64 / Tecnologí a Extended Memor y
*It is recommende d to use processors 64
with 95W power consumption.
FSB
533 / 800 / 1066 MHz
Conjunto
VIA P4M890
de chips
VIA VT8237A
Gráficos
Integrados en el conjunto de chips
UniChrome Pro
ITE 8712F
Memoria máxima de ví deo compartida de 64MB
Iniciativas de control de entor no,
Le ofrece las funcionalidades
Súper E/S hereda das de uso más común Súper
E/S.
Monitor hardware
Controlador de velocida d de ve ntilador
Función "Guardia intelige nte" de I TE
Interfaz de cue nta Low Pin
Ranuras DIMM DDR 2 x 2
Admite DDR2 de 533
Memoria
Cada DIMM admite DDR de 256MB
principal
/512MB /1GB / 2GB
Capacidad máxima de memoria de
Módulo de memoria DDR2 de canal Sencillo
No admite DIMM re gistrados o DIMM compatibl es
con ECC
4GB
Controlador IDE inte grado
IDE
Modo bus maestro Ultra DMA 33 / 66 / Soporte los Mo dos PIO 0~4,
100 / 133
Controlador ATA Serie Integra do
SATA
Tasas de transfere ncia de hasta 1.5
Compatible con la versión SATA 1.0.
Gb/s.
Red Local
Códecs de
sonido
Ranuras
36
Negociación de 10 / 100 Mb/s
Realtek RTL 8201CL PH Y
Funciones Half / F ull dúplex
Soporte de soni do de Alta Defi nición
ALC861V D
Salida de sonido de 5.1 canales
Ranura PCI
X2
Ranura PCI Ex press x16
X1
Ranura PCI ex press x 1
X1
P4M890-M7 SE
Especificación
Cada conector soporta 2 uni dades de disco
Conector disco flexible
X1
Conector IDE
X2
Cada conector soporta 2 dispositivos IDE
Conector SATA
X2
Cada conector soporta 1 dispositivos SATA
Conector de pa nel fro ntal
X1
Soporta instalaciones en el panel fr ontal
Conector de sonido frontal
X1
Soporta funcio nes de sonido e n el pa nel frontal
Conector de entra da de C D
X1
Soporta funció n de e ntrada de sonido de CD
Conector de salida S/PDIF
Conectore Cabecera de ve ntilador de C PU
flexible
X1
Soporta funció n de salida de sonido di gital
X1
Fuente de alime ntación de ve ntilador de CPU (con
s en placa
funció n Smart Fan)
Cabecera de ve ntilador de
sistema
X1
Cabecera de borrado de CMOS
X1
Conector USB
X2
Conector de alimentación
X1
Fuente de alimentación de ventilador de sistema
Cada conector soporta 2 puertos USB fro ntales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Panel
trasero de
E/S
Tamaño de
la placa
Teclado PS/2
X1
Ratón PS/2
X1
Puerto serie
X1
Puerto de impr esora
X1
Puerto VGA
X1
Puerto de re d local
X1
Puerto USB
X4
Conector de sonido
X3
190mm. (A) X 244 Mm. (H)
Soporte de
sistema
operativo
Windows 2K / XP
Biostar se reserva el derecho de aña dir o r etirar el
soporte de cualquier SO con o sin aviso previo.
37
Motherboard Manual
PORT UGUESE
ESPECIFICAÇÕES
LGA 775
Processador Intel Cor e2Duo/ Pentium Suporta as tecnologias Hyper -Threa ding /
CPU
4 / Pentium D / Celero n D até 3,8 GHz Execute Disable Bit / Enhanced I ntel SpeedStep®
*It is recommende d to use processors / Intel Arquitecture - 64 / Extended Memory 64
with 95W power consumption.
FSB
Chipset
Placa
gráfica
533 / 800 / 1066 MHz
VIA P4M890
VIA VT8237A
Integrada no chipset U niChrome Pro
ITE 8712F
Especificaç Proporciona as funcionalida des mais
ão Super
utilizadas em termos da especificação
I/O
Super I/O.
Memória de víde o máxima partilha da: 64 MB
Iniciativas para control o do am biente
Monitorização do hardware
Controlador da velocida de da v entoinha
Função "Smart Guardia n" da I TE
Interface LPC (Low Pi n Co unt).
Ranhuras DIMM DDR2 x 2
Suporta mó dulos DDR2 533
Memória
principal
Módulo de memória DDR2 de canal simples
Cada mó dulo DIMM suporta uma
memória DDR2 de 256MB /512 MB / 1 Os módulos DIMM registados e os DIMM ECC não
são suporta dos
GB / 2GB
Capacidade máxima de memória : 4
GB
Controlador IDE inte grado
IDE
Modo Bus master Ultra DMA 33 / 66 / Suporta o modo PIO 0~4,
100 / 133
Controlador Serial ATA integra do
SATA
Velocidades de transmissão de dados
até 1.5 Gb/s.
LAN PHY
Codec de
som
Ranhuras
38
Compatibilidade com a especificação SATA versão
1.0.
Auto ne gociação de 10 / 100 MB/s
Realtek RTL 8201CL PH Y
Capacidade semi/full- duplex
Suporta a especificação High-De finition Audi o
ALC861VD
Saída de á udio de 5.1 ca nais
Ranhura PCI
x2
Ranhura PCI Express x 16
x1
Ranhura PCI Express x 1
x1
P4M890-M7 SE
ESPECIFICAÇÕES
Conector da unida de de
x1
Conector IDE
x2
Cada conector suporta 2 dispositivos IDE
Conector SATA
x2
Cada conector suporta 1 dispositivo SATA
Conector do pai nel fro ntal
x1
Para suporte de várias funções no painel fro ntal
Conector de áudio fro ntal
x1
Suporta a função de áudio no painel fr ontal
Conector para e ntrada de C Ds
x1
Suporta a e ntrada de áudi o a partir de C Ds
Conector de saída S/PDIF
x1
Conectore Conector da ve ntoinha da CPU
s na placa
Cada conector suporta 2 unidades de disquetes
disquetes
x1
Conector da ve ntoinha do
sistema
x1
Suporta a saída de áudio digital
Alimentação da ventoi nha da CPU (com a função
Smart Fan)
Alimentação da ventoi nha do sistema
Conector para limpeza do CMOS x1
Conector USB
x2
Conector de alimentação
x1
Cada conector suporta 2 portas USB no pai nel
frontal
(24 pinos)
Conector de alimentação
x1
(4 pi nos)
Teclado PS/2
x1
Rato PS/2
x1
Entradas/
Porta série
x1
Saídas no
Porta para impressora
x1
painel
Porta VGA
x1
traseiro
Porta LAN
x1
Tamanho
da pl aca
Porta USB
x4
Tomada de áudio
x3
190 mm (L) X 244 mm (A)
Sistemas
operativos
suportado
s
A Biostar reserva-se o direito de adicionar ou
Windows 2K / XP
remover suporte par a qual quer sistema operativo
com ou sem aviso pré vio.
39
Motherboard Manual
POLISH
SPEC
LGA 775
Procesor Intel Core 2Duo/ P entium 4 /
Procesor
Pentium D / Celeron D do 3,8 GHz
*It is recommende d to use processors
with 95W power consumption.
FSB
Chipset
Grafika
Obsługa Hy per-Thre ading / Execute Disabl e Bit /
Enha nced Intel SpeedStep® / I ntel
Architecture-64 / Exte nde d Memory 64
Technol ogy
533 / 800 / 1066 MHz
VIA P4M890
VIA VT8237A
Zintegrowana w chipsecie U niChrome Maks. wielkość współdzielonej pamięci video
Pro
wynosi 64MB
Gniazda DDR 2 DIMM x 2
Obsługa DDR2 533
Moduł pamięci DDR2 z trybem poje dynczego
Pamięć
Każde gniazdo DIMM obsługuje
główna
moduły 256MB / 512MB / 1GB / 2GB
DDR2
kanału
Brak obsługi Registered DIMM or az ECC DIMM
Maks. wielkość pamięci 4GB
Super I/O
ITE 8712F
Funkcje kontroli warunków prac y,
Zapewnia najbardziej powszechne
Monitor H/W
funkc je Super I/O.
Kontroler prę dkości wentylatora
Interfejs L ow Pin Count
Funkcja ITE "Smart Guar dian"
Zintegrowany kontroler IDE
IDE
Ultra DMA 33 / 66 / 100 / 133 Tryb
obsługa PIO tryb 0~4,
Bus Master
SATA
Zintegrowany kontroler Serial ATA
Transfer da nych do 1.5 Gb/s.
Zgodność ze specyfikacją SATA w wersji 1.0.
10 / 100 Mb/s z automatyczną negocjacją
LAN PHY
szybkości
Realtek RTL 8201CL PH Y
Działanie w trybie połowicznego / pełnego
dupleksu
Kodek
dźwiękowy
Gniazda
40
Obsługa Hi gh- Definitio n Audio
ALC861VD
5.1 ka nałowe wy jście audio
Gniazdo PCI
x2
Gniazdo PCI Express x 16
x1
Gniazdo PCI Express x 1
x1
P4M890-M7 SE
SPEC
Złącza
Złącze napędu dyskietek
x1
Każde złącze obsługuje 2 na pędy dyskietek
Złącze IDE
x2
Każde złącze obsługuje 2 urządze nia I DE
Złącze SATA
x2
Każde złącze obsługuje 1 urządze nie SATA
Złącze panela przedniego
x1
Obsługa eleme ntów pa nela przedniego
Przednie złącze a udio
x1
Obsługa funkcji audio na pa nelu przednim
Złącze wejścia CD
x1
Obsługa funkcji wejścia a udio CD
Złącze wyjścia S/PDIF
x1
Obsługa funkcji cyfrowe go wy jścia audi o
Złącze główkowe wentylatora
wbudowan procesora
e
Zasilanie wentylatora pr ocesora (z funkcją Smart
x1
Złącze główkowe wentylatora
systemowego
x1
Fan)
Zasilanie wentylatora systemowego
Złącze główkowe kasowani a
CMOS
x1
Złącze USB
x2
Złącze zasilania (24 pi nowe)
x1
Złącze zasilania (4 pinowe)
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Port szeregowy
x1
Back Panel Port druk arki
x1
I/O
Port VGA
x1
Port LAN
x1
Port USB
x4
Gniazdo audio
x3
Wymiary
płyty
190 mm (S) X 244 mm (W)
Obsluga
systemu
operacyjn
ego
Każde złącze obsługuje 2 porty USB na pa nelu
przednim
Biostar zastrzega sobie prawo do dawania lub
Windows 2K / XP
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomie nia.
41
Motherboard Manual
RUSSIAN
СПЕЦ.
CPU
LGA 775
(центра ль Процессор Intel Core 2Duo/ Pe ntium
ный
4 / Pentium D / Celero n D до 3.8 ГГц
процессор *It is recommende d to use processors
)
with 95W power consumption.
FSB
533 / 800 / 1066 МГц
Набор
микросхе
м
Графика
Подде ржка техноло гий Hy per-Thre ading /
Execute Disable Bit / Enhanced I ntel SpeedStep®
/ Intel Architecture- 64 / Extended M emory 64
Technol ogy
VIA P4M890
VIA VT8237A
Встроенная в набо р м икросхем
Максимальная совмес тно используемая видео
UniChrome Pro
память состав ляет 64 МБ
Слоты DDR2 DIMM x 2
Модуль памя ти с однока наль ным режим ом
Подде ржка DDR2 533
DDR2
Основная Каждый модуль DIMM
память
поддержива ет 256MB / 512МБ / 1ГБ Не подде рживае т за рег истриров анные моду ли
/ 2ГБ DDR2
DIMM and ECC DIMM
Максимальная ёмк ость памя ти 4 ГБ
ITE 8712F
Super I/O
Обеспечива ет на ибо лее
Инициа тивы по охране ок ружающей среды,
используемые дейс твующие
Аппара тный монитор
функциональные возможности
Регуля тор скорости
Super I/O.
Функция ITE "Smart Guardian"
Инте рфейс с низким к оличеством
(Интелле ктуа льна я защ ита)
выводов
Встроенное устройств о у прав ления Режим "хозя ина " ш ины Ultra DMA 33 / 66 / 100
IDE
SATA
Локаль на
я сеть
Звуково й
кодек
Слоты
42
встрое нными интерфе йсами
/ 133
устройс тв
Подде ржка режима PIO 0~4,
Встроенное последов ате льное
скорость передач и данных до 1.5 гигабит/с.
устройс тво управле ния ATA
Соотве тств ие спецификации SATA версия 1.0.
Автоматическое сог ласова ние 10 / 100 М б/с
Realtek RTL 8201CL PH Y
Частич ная / полная дуплексна я способность
Звукова я поддержка High-De finition
ALC861VD
5.1кана льный звуков ой выход
Слот PCI
x2
Слот PCI Ex press x16
x1
Слот PCI Ex press x 1
x1
P4M890-M7 SE
СПЕЦ.
Встроенн
ый разъём
Разъём НГМД
x1
Разъём IDE
x2
Разъём SATA
x2
Разъём на лицево й пане ли
x1
Входно й звук овой раз ъём
x1
Разъём вв ода для CD
x1
Разъём выво да для S/PDIF
x1
Каждый разъём подде рживае т 2 нако пителя на
гибк их ма гнитных дисках
Каждый разъём по дде рживае т 2 встрое нных
интерфейса накопителе й
Каждый разъём по дде рживае т 1 устро йство
SATA
Подде ржка устро йств на лицево й па нели
Подде ржка звук овых функций на лицево й
пане ли
Подде ржка фу нкции вво да для CD
Подде ржка выво да циф рово й звуко вой
функции
Контак тирующее приспосо бле ние
Источник пита ния для ве нтиля тора
вентиля тора центра льно го
центра льно го процессора (с фу нкцией
процессора
x1
Контак тирующее приспосо бле ние
вентиля тора системы
x1
интелле ктуа льно го вентилято ра)
Источник пита ния для ве нтиля тора сис темы
Открытое контак тирующее
прис пособление CMOS
x1
USB-разъём
x2
Разъем питания ( 24 вывод)
x1
Разъем питания ( 4 вывод)
x1
Клавиа тура PS/ 2
x1
Мышь PS/2
x1
Задняя
Последо вате льный по рт
x1
пане ль
Порт подключ ения принтера
x1
средств
Порт VGA
x1
ввода-выв Порт LAN
x1
USB-порт
x4
ода
Каждый разъём по дде рживае т 2 USB-порта на
лицевой панели
Гнездо для по дключ ения
наушников
Размер
пане ли
Подде ржк
а OS
x3
190 мм (Ш) X 244 мм (В)
Biostar сохраня ет за собо й прав о добав лять
Windows 2K / XP
или уда лять сре дства обес пече ния для OS с
или без пре дварительного уведомле ния.
43
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪LGA 775‬‬
‫‪Intel Core2Duo/ Penti um 4 /‬ﻡﻌﺎﻟﺠﺎت‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫ﺑ ﺘﺮدد ﻳﺼﻞ إﻟﻰ ‪Pentium D / Celeron D 8.3‬‬
‫اﻟﻤﺮآﺰﻳ ﺔ‬
‫ﺝﻴﺠﺎ هﺮﺕﺰ‬
‫‪*It is recommende d to use processors‬‬
‫‪ Hyper -Thr eadi ng / Ex ecute Disa ble Bit‬ﺕﺪﻋﻢ ﺕﻘﻨﻴ ﺎت‬
‫‪/ Enha nced I ntel Spee dStep® / Exte nde d‬‬
‫‪Memory 64 Technology‬‬
‫‪with 95W power consumption.‬‬
‫اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ‬
‫اﻟﺠﺎﻥﺒﻲ‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت‬
‫ﻡﻴﺠﺎ هﺮﺕﺰ ‪ 533 / 800 / 1066‬ﺕﺮدد‬
‫‪VIA P4M890‬‬
‫‪VIA VT8237A‬‬
‫‪ UniChr ome Pr o‬ﻡﺪﻡﺠﺔ ﻓﻲ رﻗﺎﺋﻖ‬
‫ﻓﺘﺤﺔ‪DDR2 DIMM‬‬
‫ﻡﻴﺠﺎ ﺑﺎﻳﺖ‪64‬أﻗﺼﻰ ﺳﻌ ﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ‬
‫ﻋﺪد‪4‬‬
‫ﻡﻴﺠﺎ ﺑﺎﻳﺖ ‪ 533‬ﺳﻌﺎت ‪ DDR2‬ﺕﺪﻋﻢ اﻟﺬاآﺮ ة ﻡﻦ ﻥﻮع‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﺳﻌﺔ ‪ DDR2‬ﺕﺪﻋﻢ ذاآﺮ ة ﻡﻦ ﻥﻮع ‪ DIMM‬ﺕﺪﻋﻢ آﻞ ﻓﺘﺤﺔ أﺣﺎدﻳﺔ اﻟﻘﻨﺎة ‪DDR2‬وﺣﺪة ذا آﺮة‬
‫ﻡﻴﺠﺎ ﺑﺎﻳﺖ و‪ 1‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ ‪ /512 2 /‬ﻡﻴﺠﺎ ﺑﺎﻳﺖ ‪ ECC 256‬اﻟﻤﺴﺠﻠﺔ وﺕﻠﻚ اﻟﺘ ﻲ ﻻ ﺕﺘﻮاﻓﻖ ﻡ ﻊ ‪DIMM‬ﻻ ﺕﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 4‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫‪Super I/O‬‬
‫‪ITE 8712F‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻡ ًﺎ ‪ Super I /O .‬ﺕﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫‪ Low Pi n Count Interfac e‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ‬
‫ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣ ﺔ‬
‫‪ ITE‬ﻡﻦ "‪"Smart Guar dian‬وﻇﻴﻔﺔ‬
‫ﻡﺘﻜﺎﻡﻞ ‪ IDE‬ﻡﺘﺤﻜﻢ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫‪Ultra DMA 33 / 66 / 100 / 133‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫وﺿﻊ رﺋﻴﺴﻲ‬
‫‪SATA‬‬
‫ﻡﺘﻜﺎﻡﻞ‪ Serial ATA‬ﻡﺘﺤﻜﻢ‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺕﺼﻞ إﻟﻰ‪ 1.5‬ﺝﻴﺠﺎﺑﺖ‪ /‬ﺙﺎﻥﻴﺔ‪.‬‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪Realtek RTL 8201CL PH Y‬‬
‫آﻮدﻳﻚ اﻟﺼﻮ ت‬
‫‪ALC861VD‬‬
‫اﻟﻔﺘﺤﺎت‬
‫‪ 1.0.‬اﻹﺹﺪار ‪ SATA‬ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﺕﻔﺎوض ﺕﻠﻘﺎﺋﻲ ‪ 100 /10‬ﻡﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺙﺎﻥﻴﺔ‬
‫إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻡﻦ‬
‫‪5.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮ ت‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد ‪2‬‬
‫ﻓﺘﺤﺔ ‪PCI Expressx16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ‪PCI Express x 1‬‬
‫ﻋﺪد ‪1‬‬
‫‪44‬‬
‫‪P4M890-M7 SE‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫اﻟﻠﻮﺣ ﺔ‬
‫ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮا ص اﻟﻤﺮﻥﺔ‬
‫ﻡﻨﻔﺬ‪IDE‬‬
‫ﻋﺪد ‪2‬‬
‫‪ IDE‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة‬
‫ﻡﻨﻔﺬ‪SATA‬‬
‫ﻋﺪد ‪2‬‬
‫‪ SATA‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة‬
‫ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﺕﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮ ت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ‪CD-IN‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡ ﺞ‬
‫ﻡﻨﻔﺬ ﺥﺮج‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤ ﻲ‬
‫وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫(‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ) ﻡﻊ وﻇﻴﻔﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫وﺹﻠﺔ ﻡﺴﺢ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ‪USB‬‬
‫ﻋﺪد ‪2‬‬
‫ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪ 4‬دﺑﺎﺑﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻡﻔﺎﺕﻴﺢ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺕﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ دﺥﻞ‪ /‬ﺥﺮج‬
‫ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﻡﻨﻔﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺕﺼﺎل ﻡﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد ‪4‬‬
‫ﻡﻘﺒﺲ ﺹﻮت‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬
‫دﻋﻢ أﻥﻈﻤﺔ‬
‫اﻟﺘﺸﻐﻴﻞ‬
‫‪45‬‬
‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‪ USB‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﻋﺪد‪3‬‬
‫‪ 190‬ﻡﻢ )ﻋﺮض (‪ 244 X‬ﻡﻢ ) ارﺕﻔﺎع(‬
‫‪Windows 2K / XP‬‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ‪ Biostar‬ﺕﺤﺘﻔﻆ‬
‫ﺑﺈﺥﻄﺎر أو ﺑﺪون إﺥﻄﺎر ‪.‬‬
Motherboard Manual
JAPANESE
仕様
LGA 775
Intel Core2Duo/ Pe ntium 4 / Pentium
CPU
D / Celeron D processor up to 3.8 GHz
*It is recommende d to use processors
with 95W power consumption.
FSB
Hyper -Thre ading / Exec ute Disabl e Bit /
Enha nced Intel SpeedStep® / I ntel
Architecture-64 / Exte nde d Memory 64
Technol ogy をサポートします
533 / 800 / 1066 MHz
チップセッ VIA P4M890
ト
グラフィッ
VIA VT8237A
UniChrome Pro チップセットに統合
最大の共有ビデオメモリは64MBです
クス
DDR2 DIMMスロット x 2
メインメモ
リ
DDR2 533をサポート
シングル チャンネルモードDDR 2メモリモジュール
各DIMMは 256/ 512MB/1GB/ 2GB
登録済みDIMMとECC DIMMはサポートされません
DDR2をサポート
最大メモリ容量4GB
Super I/O
ITE 8712F
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシー
H/Wモニター
Super I/O機能を採用しています。
ファン速度コントローラ/ モニター
低ピンカウントインターフェイス
ITEの「スマートガーディアン」機能
統合IDEコントローラ
IDE
Ultra DMA 33 / 66 / 100 / 133バスマス PIO Mode 0~4のサポート、
タモード
SATA
LAN PHY
統合シリアルATAコントローラ
SATAバージョン1.0仕様に準拠。
最高1.5 Gb/秒のデータ転送速度
10 / 100 Mb/秒のオートネゴシエーション
Realtek RTL 8201CL PH Y
半/全二重機能
サウンド
Codec
スロット
46
ハイデフィニションオーディオのサポート
ALC861VD
5.1 チャンネルオーディオアウト
PCIスロット
x2
PCI Expr ess x16スロット
x1
PCI Expr ess x 1スロット
x1
P4M890-M7 SE
仕様
各コネクタは2つのフロッピードライブをサポートし
フロッピーコネクタ
x1
IDEコネクタ
x2
各コネクタは2つのIDEデバイスをサポートします
SATAコネクタ
x2
各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
CDインコネクタ
x1
CDオーディオイン機能をサポートします
S/PDIFアウトコネクタ
x1
デジタルオーディオアウト機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
CMOSクリアヘッダ
x1
USBコネクタ
x2
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
PS/2キーボード
x1
PS/2マウス
x1
ます
オンボード
コネクタ
各コネクタは2つのフロントパネルUSBポートをサポ
ートします
シリアルポート
x1
背面パネル プリンタポート
x1
I/O
VGAポート
x1
LANポート
x1
USBポート
x4
オーディオジャック
x3
ボードサイ
190 mm (幅) X 244 mm (高さ)
ズ
OSサポー
ト
Windows 2K / XP
Biostarは事前のサポートなしにOSサポートを追加ま
たは削除する権利を留保します。
2007/04/11
47
P4M890-M7 SE BIOS Setup
BIOS Setup .................................................................................................1
1 Main Menu...............................................................................................3
2 Standard CMOS Features......................................................................7
3 Advanced BIOS Features .......................................................................9
4 Advanced Chipset Features..................................................................17
5 Integrated Peripherals..........................................................................21
6 Power Management Setup....................................................................27
7 PnP/PCI Configurations.......................................................................32
8 PC Health Status ...................................................................................35
9 Performance Booster Zone...................................................................37
i
P4M890-M7 SE
BIOS Setup
Introduction
The purpose of this manual is to describe the settings in the Phoenix-Award™
BIOS Setup program on this motherboard. The Setup program allows users to
modify the basic system configuration and save these settings to CMOS RAM.
The power of CMOS RAM is supplied by a battery so that it retains the Setup
inform ation when the power is turned off.
Basic Input-Output System (BIOS) determines what a computer can do without
accessing programs from a disk. This system controls most of the input and
output devices such as keyboard, mouse, serial ports and disk drives. BIOS
activates at the first stage of the booting process, loading and executing the
operating system. Some additional features, such as virus and password
protection or chipset fine-tuning options are also included in BIOS.
The rest of this manual will to guide you through the options and settings in
BIOS Setup.
Plug and Pla y Support
This PHOENIX-AWARD BIOS supports the Plug and Play Version 1.0A
speci fication and ESCD (Extended System Configuration Data) write.
EPA Green PC Support
This PHOENIX-AWARD BIOS supports Version 1.03 of the EPA Green PC
speci fication.
APM Support
This PHOENIX-AWARD BIOS supports Version 1.1&1.2 of the Advanced
Power Management (APM) speci fication. Power management features are
implemented via the System Management Interrupt (SMI). Sleep and Suspend
power management modes are supported. Power to the hard disk drives and
video monitors can also be managed by this PHOENIX-AWARD BIOS.
1
P4M890-M7 SE
ACPI Support
Phoenix-Award ACPI BIOS support Version 1.0b of Advanced Configuration
and Power interface speci fi cation (ACPI). It provides ASL code for power
management and devi ce configuration capabilities as defined in the ACPI
speci fication, developed by Microsoft, Intel and Toshiba.
PCI Bus Support
This PHOENIX-AWARD BIOS also supports Version 3.0 of the Int el PCI
(Peripheral Component Interconnect) local bus specification.
DRAM Support
DDR SDRAM (Double Data Rate Synchronous DRAM) is supported.
Supported CPUs
This PHOENIX-AWARD BIOS supports the Intel CPU.
Using Setup
Use the arrow keys to highlight items in most of the place, press <Enter> to
select, use the <PgUp> and <PgDn> keys to change entries, press <F1> for help
and press <Esc> to quit. The following table provides more detail about how to
navigate in the Setup program by using the keyboard.
Keystroke
Up arrow
Down arrow
Left arrow
Right arrow
Move Enter
PgUp key
PgDn key
+ Key
- Key
Esc key
F1 key
F5 key
F7 key
F10 key
Function
Move to previous item
Move to next item
Move to the item on the left (menu bar)
Move to the item on the right (menu bar)
Move to the item you desired
Increas e the numeric val ue or make c hanges
Decrease the numeric value or make changes
Increas e the numeric val ue or make c hanges
Decrease the numeric value or make changes
Main Menu – Quit and not s ave c hanges into CMOS
Status Page Setup Menu and Option Page Setup Menu – Exit
Current page and r eturn to M ain Menu
General help on Setup navigation keys
Load pr evious values from CMOS
Load the opti mized defaults
Save all the CMOS c hanges and exit
2
P4M890-M7 SE
1 Main Menu
Once you enter Phoenix-Award BIOS™ CMOS Setup Utility, the Main Menu
will appear on the screen. The Main Menu allows you to select from several
setup functions. Use the arrow keys to select among the items and press <Enter>
to accept and enter the sub-menu.
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described in
this manual (Figure 1, 2, 3, 4, 5, 6, 7, 8, 9) is for your
reference only. The actual BIOS information and settings on
board may be slightly different from this manual.
„ Figure 1: Main Menu
Standard CMOS Features
This submenu contains industry standard configurable options.
Advanced BIOS Features
This submenu allows you to configure advanced features of the BIOS.
3
P4M890-M7 SE
Advanced Chipset Features
This submenu allows you to configure special chipset features.
Integrated Peripherals
This submenu allows you to configure cert ain IDE hard drive options and
Programmed Input/ Output features.
Power Management Setup
This submenu allows you to configure the power managem ent features.
PnP/PCI Configurations
This submenu allows you to configure cert ain “ Plug and Play” and PCI options.
PC Health Status
This submenu allows you to monitor the hardware of your system.
Performance Booster Zone
This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock.
(However, we suggest you to use the default setting. Changing the voltage and
clock improperly may damage the CPU or M/B!)
Load Optimized Defaults
This selection allows you to reload the BIOS when problem occurs during
system booting sequence. These configurations are factory settings optimized
for this system. A confirmation message will be displayed before defaults are
set.
4
P4M890-M7 SE
Set Supervisor Password
Setting the supervisor password will prohibit everyone except the supervisor
from making changes using the CMOS Setup Utility. You will be prompted with
to enter a password.
Set User Password
If the Supervisor Password is not set, then the User Password will function in
the same way as the Supervisor Password. If the Supervisor Password is set and
the User Password is set, the “User” will only be able to view configurations but
will not be able to change them.
Save & Exit Setup
Save all configuration changes to CMOS (memory) and exit setup. Confirmation
message will be displayed before proceeding.
Exit Without Sa ving
Abandon all changes made during the current session and exit setup.
Confirmation message will be displayed before proceeding.
5
P4M890-M7 SE
Upgrade BIOS
This submenu allows you to upgrade bios.
6
P4M890-M7 SE
2 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categori es.
Each category includes no, one or more than one setup items. Use the arrow
keys to highlight the item and then use the<PgUp> or <PgDn> keys to select the
value you want in each item.
„ Figure 2: Standard CMOS Setup
Main Menu Selections
This table shows the items and the available options on the Main Menu.
Item
Options
Description
Date
mm : dd : yy
Set the system date. Note
that the ‘Day ’ automatically
changes when you set the
date.
Time
hh : mm : ss
Set the system internal
clock.
IDE Channel 0 Master
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options
IDE Channel 0 Slav e
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
7
P4M890-M7 SE
Item
Options
Description
IDE Channel 1 Master
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
IDE Channel 1 Slav e
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
360K, 5.25 in
1.2M, 5.25 in
Driv e A
720K, 3.5 in
Driv e B
1.44M, 3.5 in
Select the ty pe of f loppy
disk drive installed in your
sy stem.
2.88M, 3.5 in
None
All Errors
No Errors
Halt On
All, but Key board
All, but Diskette
Select the situation in which
y ou want the BIOS to stop
the POST process and
notify y ou.
All, but Disk/ Key
Base Memory
N/A
Displays the amount of
conv entional memory
detected during boot up.
Extended Memory
N/A
Displays the amount of
extended memory detected
during boot up.
Total Memory
N/A
Displays the total memory
av ailable in the system.
8
P4M890-M7 SE
3 Advanced BIOS Features
„ Figure 3: Advanced BIOS Setup
Boot Seq & Floppy Setup
This item allows you to setup boot sequence & Floppy.
9
P4M890-M7 SE
Hard Disk Boot Priority
The BIOS will attempt to arrange the Hard Disk boot sequence automatically.
You can change the Hard Disk booting sequence here.
The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USB HDD0, USB
HDD1, USB HDD2, and Bootable Add-in Cards.
First/Second/Third Boot Dev ice
The BIOS will attempt to load the operating system in this order.
The Choices: Floppy, LS120, Hard Disk, CDROM, ZIP 100, USB-FDD,
USB-ZIP , USB-CDROM, LAN, Disabled.
Boot Other Dev ice
When enabled, BIOS will try to load the operating system from other device
when it failed to load from the three devices above.
The Choices: Enabled (default), Disabled
Sw ap Floppy Drive
For systems with two floppy drives, this option allows you to swap logical
drive assignments.
The Choices: Disabled (default), Enabled.
10
P4M890-M7 SE
Boot Up Floppy Seek
When enabled, System will test the floppy drives to determine if they have 40
or 80 tracks during boot up. Disabling this option reduces the time it takes to
boot-up.
The Choices: Enabled (default), Disabled.
Shadow Setup
„
This item allows you to setup cache & shadow setup.
Figure 3.2: Shadow Setup
Video BIOS Shadow
Determines whether video BIOS will be copied to RAM for faster execution or
not.
Enabled (default) Optional ROM is enabled.
Disabled Optional ROM is disabled.
11
P4M890-M7 SE
Cache Setup
CPU L1 & L2 Cache
Depending on the CP U/chipset in use, you may be able to increase me mory
access time with this option.
Enabled (default) Enable cache.
Disabled
Disable cache.
CPU L3 Cache
Depending on the CP U/chipset in use, you may be able to increase me mory
access time with this option.
Enabled (default) Enable cache.
Disabled
Disable cache.
CPU L2 Cache ECC Checking
This item allows you to enable/disable CPU L2 Cache ECC Checking.
The Choices: Enabled (default), Disabled.
12
P4M890-M7 SE
CPU Feature
Delay Prior to Thermal
Set this item to enable the CP U Thermal function to engage after the specified
time.
The Choices: 4 Min, 8 Min, 16Min (default), 32 Min.
Thermal Management
This option allows you to select the way to control the “ Thermal Management.”
The Choices: Thermal Monitor 1 (default), Thermal Monitor 2.
TM2 Bus Ratio
This option represents the frequency (bus ratio) of the throttled performance
state that will be initiated when the on-die sensor detects temperature increase.
Min=
0
Max= 255
Key in a DEC number.
The Choices: 0 X (default)
TM2 Bus VID
This option represents the voltage of the throttled performance state that will be
initiated when the on-die sensor detects temperature increase.
The Choices: 0.8375V (default), 0.8375-1.6000.
13
P4M890-M7 SE
Limit CPUID MaxVal
Set Limit CP UID MaxVal to 3, it should be “ Disabled” for Windows XP .
The Choices: Disabled (default), Enabled.
C1E Function
This item allows you to configure the Enhanced Halt State (C1E) function,
which may reduce the power consumption of your system when the system is
idle.
The Choices: Auto (default),Disabled.
Execute Disable Bit
This item allows you to configure the Execute Disabled Bit function, which
protects your system from buffer overflow attacks.
The Choices: Enabled (default), Disabled.
Virtualization Technology
Virtualization Technology can virtually separate your system resource into
several parts, thus enhance the performance when running virtual machines or
multi interface systems.
The Choices: Enabled (default), Disabled.
Virus Warning
This option allows you to choose the VIRUS Warning feature that is used to
protect the IDE Hard Disk boot sector. If this function is enabled and an attempt
is made to write to the boot sector, BIOS will display a warning message on the
screen and sound an alarm beep.
Disabled (default) Virus protection is disabled.
Enabled
Virus protection is activated.
Hyper-Threading Technology
This option allows you to enable or disabled Hyper-Threading Technology.
“ Enabled” for Windows XP and Linux 2.4.x (OS optimized for
Hyper-Threading Technology). “ Disable” for other OS (OS not optimized for
Hyper-Threading Technology).
The Choices: Enabled (default), Disabled.
14
P4M890-M7 SE
Quick Power On Self Test
Enabling this option will cause an abridged version of the Power On Self-Test
(POST) to execute after you power up the computer.
Disabled
Normal POST.
Enabled (default) Enable quick POST.
Boot Up NumLock Status
Selects the NumLock State after the system switched on.
The Choices:
On (default) Numpad is number keys.
Off
Numpad is arrow keys.
Typematic Rate Setting
When a key is held down, the keystroke will repeat at a rate determined by the
keyboard controller. When enabled, the typematic rate and typematic delay can
be configured.
The Choices: Disabled (default), Enabled.
Typematic Rate (Chars/Sec)
Sets the rate at which a keystroke is repeated when you hold the key down.
The Choices: 6 (default), 8, 10, 12, 15, 20, 24, 30.
Typematic Dela y (Msec)
Sets the delay time after the key is held down before it begins to repeat the
keystroke.
The Choices: 250 (default), 500, 750, 1000.
Security Option
This option will enable only individuals with passwords to bring the system
online and/or to use the CMOS Setup Utility.
System:
A password is required for the system to boot and is also
required to access the Setup Utility.
Setup (default):
A password is required to access the Setup Utility only.
This will only apply if passwords are set from the Setup main menu.
15
P4M890-M7 SE
MPS Version Control For OS
The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor speci fication.
Select version supported by the operation system running on this computer.
The Choices: 1.4 (default), 1.1.
OS Select For DRAM > 64MB
A choice other than Non-OS2 is only used for OS2 systems with memory
exceeding 64MB.
The Choices: Non-OS2 (default), OS2.
HDD S.M.A.R.T. Capability
This item allows you to enable/disable HDD S.M.A.R.T. Capability.
The Choices: Disabled (default), Enabled.
Small Logo(EPA) Show
This item allows you to select whether the “Small Logo” shows. Enabled
(default) “ Small Logo” shows when system boots up. Disabled No “Small
Logo” shows when system boots
The Choices: Enabled (default), Disabled
Summary Screen Show
This item allows you to enable/disable the summary screen.
means system configuration and PCI device listing.
The Choices: Disabled (default), Enabled.
16
Summary screen
P4M890-M7 SE
4 Advanced Chipset Features
„
This submenu allows you to configure the speci fic features of the chipset
installed on your system. This chipset manage bus speeds and access to system
memory resources, such as DRAM. It also coordinates communications with the
PCI bus. The default settings that came with your system have been optimized
and therefore should not be changed unless you are suspicious that the settings
have been changed incorrectly.
Figure 4: Advanced Chipset Setup
17
P4M890-M7 SE
AGP & P2P Bridge Control
Highlight “Press Enter” next to the “ AGP & P2P Bridge Control” label and
pressing the enter key will take you a submenu with the following options:
„ Figure 4.1:
AGP & P2P Bridge Control
AGP Aperture Size
Select the size of the Accelerated Graphics Port (AGP ) aperture. The aperture
is a portion of the P CI memory address range dedicated for graphics memory
address space. Host cycles that hit the aperture range are forwarded to the AGP
without the need of translation.
The Choices: 32M, 64M, 128M (default), 256M.
AGP 2.0 Mode
This item allows you to select the AGP Mode.
The Choices: 8X (default), 4X.
AGP Master 1 WS Write
When enabled, writes to the AGP (Accelerated Graphics P ort) are executed
with one wait states.
The Choices: Enabled (default), Disabled.
18
P4M890-M7 SE
AGP Master 1 WS Read
When enabled, read to the AGP (Accelerated Graphics P ort) are executed with
one wait states.
The Choices: Enabled (default), Disabled.
VGA Share Memory Size
This item allows you to select the VGA share memory size.
The Choices: 64M (default), 16M, 32M, 128M, 256M, Disabled
Direct Frame Buffer
This item allows you to disabled or enabled direct frame buffer
The Choices: Enabled (default), Disabled.
CPU & PCI Bus Control
By highlighting the “Press Enter” label next to the “CPU & PCI Bus Control”
and press the enter key, it will take you a submenu with the following options:
„ Figure 4.2: CPU & PCI Bus Control
PCI Master 0 WS Write
When enabled, writes to the P CI bus are executed with zero-wait states.
The Choices: Enabled (default), Disabled.
19
P4M890-M7 SE
PCI Delay Transaction
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with P CI
specification.
The Choices: Enabled (default), Disabled.
Vlink mode selection
This item allows you to select Vlink mode.
The Choices: B y Auto (default), Mode 0 , Mode 1.
VLink 8X Support
This item allows you to enable or disable VLink 8X support.
The Choices: Enabled (default), Disabled.
VIA PWR Management
The Choices: Enabled (default), Disabled.
Memory Hole
You can reserve this area of system memory for ISA adapter ROM. When this
area is reserved it cannot be cached. Check the user information of peripherals
that need to use this area of system memory for the memory requirements.
The Choices: Disabled (default), Enabled.
System BIOS Cacheable
Selecting the “ Enabled” option allows caching of the system BIOS ROM at
F0000h-FFFFFh, which is able to improve the system performance. However,
any programs that attempts to write to this memory block will cause conflicts
and result in system errors.
The Choices: Enabled (default), Disabled.
Top Performance
The Choices: Disabled (default), Enabled.
20
P4M890-M7 SE
5 Integrated Peripherals
„ Figure 5. Integrated Peripherals
VIA OnChip IDE Device
Highlight the “Press Enter” label next to the “ VIA OnChip IDE Device” label
and press enter key will take you a submenu with the following options:
21
P4M890-M7 SE
SATA Controller
This option allows you to enable the on-chip Serial ATA.
The Choices: Enabled (default), Disabled.
SATA Controller Mode
This option allows you to select SATA Mode.
The Choices: RAID, IDE (default).
IDE DMA Transfer Access
This item allows you to enable or disable the IDE DMA transfer access.
The Choices: Enabled (default), Disabled.
On-chip IDE Channel 0/1
The motherboard chipset contains a P CI IDE interface with support for two
IDE channels. Select “ Enabled” to activate the first and/or second IDE interface.
Select “ Disabled” to deactivate an interface if you are going to install a primary
and/or secondary add-in IDE interface.
The Choices: Enabled (default), Disabled.
IDE Prefetch Mode
The “ onboard” IDE drive interfaces supports IDE prefetch function for faster
drive access. If the interface on your drive does not support prefetching, or if
you install a primary and/or secondary add-in IDE interface, set this option to
“ Disabled”.
The Choices: Enabled (default), Disabled.
Primary/Secondary/Master/Slave PIO
The IDE P IO (P rogrammed Input / Output) fields let you set a P IO mode (0-4)
for each of the IDE devices that the onboard IDE interface supports. Modes 0
to 4 will increase performance progressively. In Auto mode, the system
automatically determines the best mode for each device.
The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4.
22
P4M890-M7 SE
Primary/Secondary/Master/Slave UDMA
Ultra DMA function can be implemented if it is supported by the IDE hard
drives in your system. As well, your operating environment requires a DMA
driver (Windows 95 or OSR2may need a third party IDE bus master driver). If
your hard drive and your system software both support Ultra DMA, select Auto
to enable BIOS support.
The Choices: Auto (default), Disabled.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple
sectors read / write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block mode (most new drives do), select Enabled for automatic detection of the
optimal number of block read / write per sector where the drive can support.
The Choices: Enabled (default), Disabled.
VIA OnChip PCI Device
„
Highlight the “Press Enter” label next to the “ VIA OnChip PCI Device” label
and press the enter key will take you a submenu with the following options:
Figure 5.2: VIA OnChip PCI Device
Azalia HDA Controller
This option allows you to control the onboard HD audio.
The Choices: Auto (default), Disabled.
23
P4M890-M7 SE
LAN Controller
This option allows you to control the onboard LAN.
The Choices: Enabled (default), Disabled
Lan Boot ROM
Decide whether to invoke the boot ROM of the onboard LAN chip.
The Choices: Disable (default), Enabled.
Super IO Device
Press Enter to configure the Super I/O Device.
Onboard FDC Controller
Select enabled if your system has a floppy disk controller (FDC) installed on
the system board and you wish to use it. If you installed another FDC or the
system uses no floppy drive, select disabled in this field.
The Choices: Enabled (default), Disabled.
Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial
ports.
The Choices: 3F8/IRQ4 (default), Disabled, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,
Auto.
24
P4M890-M7 SE
Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with
which I/O Address.
The Choices: 378/IRQ 7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.
Parallel Port Mode
This item allows you to determine how the parallel port should function. The
default value is SPP .
The Choices:
SPP (de fault)
Using P arallel port as Standard P rinter Port.
EPP
Using P arallel P ort as Enhanced P arallel Port.
ECP
Using P arallel port as Extended Capabilities P ort.
ECP +EPP
Using P arallel port as ECP & EPP mode.
ECP Mode Use DMA
Select a DMA Channel for the port.
The Choices: 3 (default), 1.
USB De vice Setting
Press Enter to configure the USB Device.
25
P4M890-M7 SE
USB 1.0/2.0 Controller
These options allow you to enable or disable the USB 1.0/2.0 controller
function.
The Choices: Enabled (default), Disabled.
USB Operation Mode
This option let you select the operation mode of USB function.
The Choices: High Speed (default), Full/Low Speed.
USB Keyboard/Mouse/Storage Function
These options allow you to enable or disable the USB keyboard/mouse/storage
devices.
The Choices: Enabled (default), Disabled.
USB Mass Storage Dev ice Boot Setting
These options allow you to choose the boot up type of the USB mass storage
devices..
The Choices: Auto mode (default), FDD mode, HDD mode.
26
P4M890-M7 SE
6 Power Management Setup
The Power Management Setup Menu allows you to configure your system to
utilize energy conservation and power up/power down features.
„ Figure 6. Power Management Setup
ACPI Function
This item displays the status of the Advanced Configuration and Power
Management (ACPI).
The Choices: Enabled (default), Disabled.
27
P4M890-M7 SE
Power Management
This category allows you to select the power saving method and is directly
related to the following modes:
1. HDD Power Down.
2. Suspend Mode.
There are three options of Power Management, three of which have fixed mode
settings
Min. Power Saving
Minimum power management.
Suspend Mode = 1 hr.
HDD Power Down = 15 min
Max. Power Saving
Maximum power management only available for sl CPU’s.
Suspend Mode = 1 min.
HDD Power Down = 1 min.
User Define (default)
Allow you to set each option individually.
When you choose user define, you can adjust each of the item from 1 min. to 1
hr. except for HDD Power Down which ranges from 1 min. to 15 min.
HDD Power Down
When enabled, the hard-disk drives will power down after a set time of system
inactivity. All other devices remain active.
The Choices: Disabled (default), 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7
Min, 8 Min, 9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15Min.
Suspend Mode
The item allows you to adjust the system idle time before suspend.
The Choices: Disabled (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min,
20 Min, 30 Min, 40 Min, 1 Hour.
Video Off Option
This field determines when to activate the video off feature for monitor power
management.
The Choices: Suspend→Off (default), Always on.
28
P4M890-M7 SE
Video Off Method
This option determines the manner when the monitor goes blank.
V/H SYNC+Blank (default)
This selection will cause the system to turn off the vertical and horizontal
synchronization ports and write blanks to the video buffer.
Blank Screen
This option only writes blanks to the video buffer.
DPMS
Initial display power management signaling.
Modem Use IRQ
This determines the IRQ, which can be applied in MODEM use.
The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA.
Soft-Off by PWRBTN
This item determines the behavior of system power button. Instant off turn off
the power immediately, and Delay 4 Sec. will require you to press and hold the
power button for 4 seconds to cut off the system power.
The Choices: Delay 4 Sec, Instant-Off (default).
Ac Loss Auto Restart
This setting specifies how your system should behave aft er a power fail or
interrupts occurs. By choosing off will leave the computer in the power off stat e.
Choosing On will reboot the computer. Former-Sts will restore the system to the
status before power failure or interrupt occurs.
The Choices: Off (default), On, Former-Sts.
HPET Support
This option allows you to disabled or enables the High Precision Event Timer.
The Choices: Enabled (default), Disabled.
HPET Mode
This option allows you to select the modes of the High Precision Event Timer.
The Choices: 32-bit mode (default), 64-bit mode.
29
P4M890-M7 SE
WDRT Support
This option allows you to disabled or enables the Watchdog Timer.
The Choices: Enabled (default), Disabled.
WDRT Run/Stop
This option allows you to select the mode of Watchdog Timer.
The Choices: Stop (default), Run.
WDRT Count
This option allows you to control the count of the Watchdog Timer.
The Choices: 1023 (default); min=0, amx=1023, key in a DEC number.
Wakeup Event Detect
Figure 6.1:IRQ/Event Activity Detect
Highlight the “Press Enter” label next to the “ IRQ/Event Activity Detect” label
and press the enter key will take you a submenu with the following options:
30
P4M890-M7 SE
PowerOn by PCI Card
When you select Enabled, a P ME signal from P CI card returns the system to
Full ON state.
For this function to work, you may need a LAN add-on card which supports the
Wake on LAN function. Set the Wake on LAN (WOL) jumper on motherboard
to enable if applicable.
The Choices: Disabled (default), Enabled.
Modem Ring Resume
This item allows you to disable or enable Modem Ring Resume function.
The Choices: Disabled (default), Enabled.
RTC Alarm Resume
When “ Enabled”, you can set the date and time at which the RTC (real-time
clock) alarm awakens the system fro m Suspend mode.
The Choices: Disabled (default), Enabled.
Date (of Month)
You can choose which month the system will boot up. This field is only
configurable when “ RTC Resume” is set to “ Enabled”.
Resume Time (hh:mm:ss)
You can choose the hour, minute and second the system will boot up. This field
is only configurable when “ RTC Resume” is set to “ Enabled”.
31
P4M890-M7 SE
7 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal
Computer Interconnect, is a system which allows I/O devices to operate at
speeds nearing the speed of the CPU itself uses when communicating with its
own special components. This section covers some very techni cal items and it is
strongly recommended that only experienced users should make any changes to
the default settings.
„
Figure 7: PnP/PCI Configurations
PNP OS Installed
When set to YES, BIOS will only initialize the PnP cards used for the boot
sequence (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP
operating system like Window™ 95. When set to NO, BIOS will initialize all
the PnP cards. For non-PnP operating systems (DOS, Netware™), this option
must set to NO.
The Choices: No (default), Yes.
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip VGA first.
The Choices: PCIEx (default), PCI Slot, Onboard, AGP.
32
P4M890-M7 SE
Reset Configuration Data
The system BIOS supports the PnP feature which requires the system to record
which resources are assigned and protects resources from conflict.
Every peripheral device has a node, which is called ESCD. This node records
which resources are assigned to it. The system needs to record and update ESCD
to the memory locations. These locations are reserved in the system BIOS. If the
Disabled (default) option is chosen, the system‘s ESCD will update only when
the new configuration varies from the last one. If the Enabled option is chosen,
the system is forced to update ESCDs and then is automatically set to the
“ Disabled” mode.
The above settings will be shown on the screen only if “ Manual” is chosen for
the resources controlled by function.
Legacy is the term, which signifies that a resource is assigned to the ISA Bus
and provides non-PnP ISA add-on cards. PCI / ISA PnP signify that a resource
is assigned to the PCI Bus or provides for ISA PnP add-on cards and
peripherals.
The Choices: Disabled (default), Enabled.
Resources Controlled By
By Choosing “Auto(ESCD)” (default), the system BIOS will detect the system
resources and automatically assign the relative IRQ and DMA channel for each
peripheral. By Choosing “Manual”, the user will need to assign IRQ & DMA for
add-on cards. Be sure that there are no IRQ/DMA and I/O port conflicts.
The Choices: Auto (ESCD) (default), Manual.
33
P4M890-M7 SE
IRQ Resources
This submenu will allow you to assign each system interrupt a type, depending
on the type of device using the interrupt. When you press the “ Press Enter” tag,
you will be directed to a submenu that will allow you to configure the system
interrupts. This is only configurable when “ Resources Controlled By” is set to
“Manual”.
IRQ-3
assigned to PCI Device
IRQ-4
assigned to PCI Device
IRQ-5
assigned to PCI Device
IRQ-7
assigned to PCI Device
IRQ-9
assigned to PCI Device
IRQ-10
assigned to PCI Device
IRQ-11
assigned to PCI Device
IRQ-12
assigned to PCI Device
IRQ-14
assigned to PCI Device
IRQ-15
assigned to PCI Device
PCI / VGA Palette Snoop
Some old graphic controllers need to “ snoop” on the VGA palette and then map
it to their display as a way to provide boot inform ation and VGA compatibility.
This item allows such snooping to take place.
The Choices: Disabled (default), Enabled
Assign IRQ For VGA
This item allows the users to choose which IRQ to assign for the VGA.
The Choices: Enabled (default), Disabled.
Assign IRQ For USB
This item allows the users to choose which IRQ to assign for the USB.
The Choices: Enabled (default), Disabled.
Maximum Payload Size
Set the maximum payload size for Transaction packets (TLP).
The Choice: 4096 (default.), 128, 256, 512, 1024, 2048.
34
P4M890-M7 SE
8 PC Health Status
„ Figure 8: PC Health Status
Shutdown Temperature
This item allows you to set up the CPU shutdown Temperature. This item is
only effective under Windows 98 ACPI mode.
The Choices: 65℃/ 149℉, 70℃/ 158℉, 75℃/ 167℉, 80℃/ 176℉, 85℃/ 185
℉, 90℃/ 167℉, 95℃/ 194℉(default), Disabled.
CPU FAN Control by
Choose “ smart” to reduce the noise caused by CPU FAN.
The Choices: Smart, Always On (default).
CPU Fan Load (Sharp=0)
The Choices: Min=0, Max=7; key in a DEC number.
CPU Fan Start (℃)
CPU fan starts to work under smart fan function when arrive this set value.
The Choices: Min=0, Max=100; key in a DEC number.
35
P4M890-M7 SE
CPU Fan Full speed <℃>
When CPU temperature is reach the set value, the CPU fan will work under Full
Speed.
The Choices: Min=0, Max=100; key in a DEC number.
Start PWM Value (%)
When CPU temperature arrives to the set value, the CPU fan will work under
Smart Fan Function mode. The range is from 0~127, with an interval of 1.
The Choices: Min=0, Max=100; key in a DEC number.
Slope PWM Level (%/℃)
Increasing the value of slope PWM will raise the speed of CPU fan.
The Choices: 3.1%/℃ Medium(default), 0.0%/℃, 0.8%/℃, 1.6%/℃,6.3%/℃
High,12.5%/℃, 25.0%/℃, 50.0%/℃.
CPU Vcore, NB Vcore, +3.3V, +5.0V, +12V, DRAM Voltage,
VTT Voltage, Voltage Battery
Detect the system’s voltage status automatically.
Current CPU Temp
This field displays the current temperature of CPU.
Current CPU FAN Speed
This field displays the current speed of CPU fan.
Current SYS FAN Speed
This field displays the current speed SYSTEM fan.
Show H/W Monitor in POST
If you computer contains a monitoring system, it will show PC health status
during POST stage. The item offers several different delay times.
The Choices: Enabled (default), Disabled.
36
P4M890-M7 SE
9 Performance Booster Zone
„
Figure 9: Performance Booster Zone
DRAM Clock/Drive Control
„
This item controls the DRAM Clock. Highlight “Press Enter” next to the
“ DRAM Clock/Drive Control” label and pressing the enter key will take you a
submenu with the following options:
Figure 9.1: DRAM Clock/Drive Control
37
P4M890-M7 SE
DRAM Clock
This item determines DRAM clock.
The Choices: B y SPD (default), 100MHz, 133MHz, 166MHz, 200MHz,
266MHz, 333MHz .
DRAM Timing
This item determines DRAM clock/ timing.
The Choices: Auto by SPD (default), Manual, Turbo, Ultra.
SDRAM CAS Latency
When DRAM is installed, the number of clock cycles of CAS latency depends
on the DRAM timing.
The Choices: 2.5 /4(default).
Bank Interleave
This item allows you to enable or disable the bank interleave feature.
The Choices: Disabled (default).
Precharge to Active (tRP)
This item allows you to specify the delay from precharge command to activate
command.
The Choices: 4T (default).
Activ e to Precharge (tRAS)
This item allows you to specify the minimum row active time (tRAS).
The Choices: 07T (default).
Activ e to CMD (tRCD)
Use this item to specify the delay from the activation of a bank to the time that
a read or write command is accepted.
The Choices: 4T (default).
REF to ACT/REF to REF (Trfc)
This item allows you to determine the selection for REF to ACT/REF to REF
(tRFC).
The Choices: 20T/21T (default).
38
P4M890-M7 SE
ACT (0) to ACT (1) (tRRD)
This item allows you to determine the selection for ACT (0) to ACT (1) (tRRD)
The Choices: 3T (default).
1T CMD Support
The Choices: Disable (default), Auto.
DDR2 On Die Termination
This option allows you to choose the working type of ODT.
The Choices: ODT Always ON (default), Dynamic ODT, ODT Always OFF.
CPU CLOCK
This item allows you to select CPU Clock, and CPU over clocking.
Special Notice:
If the system’s frequency that you are selected is not functioning, there are two
methods of booting-up the system.
Method 1:
Clear the COMS data by setting the JCOMS1 ((2-3) closed)) as “ ON” status. All
the CMOS data will be loaded as defaults setting.
Method 2:
Press the <Insert> key and Power button simultaneously, after that keep-on
pressing the <Insert> key until the power-on screen showed.
This action will boot-up the system according to FSB of the processor
It’s strongly recommended to set CPU Vcore and clock in default setting. If the
CPU Vcore and clock are not in default setting, it may cause CPU or M/B
damage.
The Choices: 100MHz(default); Min=100, Max=400, key in a DEC number.
Async PCIE CLOCK
This item allows you to select Async PCIE clock.
Min= 100 Max=150 Key in a DEC number.
The Choices: 100MHz(default) ; Min=100, Max=150, key in a DEC number.
CPU Clock Ratio
This item allows you to select the CPU Ratio.
Min= 6 Max= 50 Key in a DEC number.
The Choices: 6X (default).
39
P4M890-M7 SE
Spread Spectrum
This item allows you to enable/disable the Spread Spectrum function.
The Choices:+/- 0.25% (default), +/- 0. 5%, Disabled, -0.5%, -1.0%.
DDR Voltage
This item allows you to select DDR Voltage.
The Choices: StartUp (default), +0.10V, +0.20V, +0.30V, +0.40V, +0.50V,
+0.60V, +0.70V.
CPU Voltage
This item allows you to select CPU Voltage.
The Choices: StartUp (default), +0.012V~+0.787V.
40
P4M890-M7 SE BIOS Setup
BIOS Setup .................................................................................................1
1 Main Menu...............................................................................................3
2 Standard CMOS Features......................................................................7
3 Advanced BIOS Features .......................................................................9
4 Advanced Chipset Features..................................................................17
5 Integrated Peripherals..........................................................................21
6 Power Management Setup....................................................................27
7 PnP/PCI Configurations.......................................................................32
8 PC Health Status ...................................................................................35
9 Performance Booster Zone...................................................................37
i
P4M890-M7 SE
BIOS Setup
Introduction
The purpose of this manual is to describe the settings in the Phoenix-Award™
BIOS Setup program on this motherboard. The Setup program allows users to
modify the basic system configuration and save these settings to CMOS RAM.
The power of CMOS RAM is supplied by a battery so that it retains the Setup
inform ation when the power is turned off.
Basic Input-Output System (BIOS) determines what a computer can do without
accessing programs from a disk. This system controls most of the input and
output devices such as keyboard, mouse, serial ports and disk drives. BIOS
activates at the first stage of the booting process, loading and executing the
operating system. Some additional features, such as virus and password
protection or chipset fine-tuning options are also included in BIOS.
The rest of this manual will to guide you through the options and settings in
BIOS Setup.
Plug and Pla y Support
This PHOENIX-AWARD BIOS supports the Plug and Play Version 1.0A
speci fication and ESCD (Extended System Configuration Data) write.
EPA Green PC Support
This PHOENIX-AWARD BIOS supports Version 1.03 of the EPA Green PC
speci fication.
APM Support
This PHOENIX-AWARD BIOS supports Version 1.1&1.2 of the Advanced
Power Management (APM) speci fication. Power management features are
implemented via the System Management Interrupt (SMI). Sleep and Suspend
power management modes are supported. Power to the hard disk drives and
video monitors can also be managed by this PHOENIX-AWARD BIOS.
1
P4M890-M7 SE
ACPI Support
Phoenix-Award ACPI BIOS support Version 1.0b of Advanced Configuration
and Power interface speci fi cation (ACPI). It provides ASL code for power
management and devi ce configuration capabilities as defined in the ACPI
speci fication, developed by Microsoft, Intel and Toshiba.
PCI Bus Support
This PHOENIX-AWARD BIOS also supports Version 3.0 of the Int el PCI
(Peripheral Component Interconnect) local bus specification.
DRAM Support
DDR SDRAM (Double Data Rate Synchronous DRAM) is supported.
Supported CPUs
This PHOENIX-AWARD BIOS supports the Intel CPU.
Using Setup
Use the arrow keys to highlight items in most of the place, press <Enter> to
select, use the <PgUp> and <PgDn> keys to change entries, press <F1> for help
and press <Esc> to quit. The following table provides more detail about how to
navigate in the Setup program by using the keyboard.
Keystroke
Up arrow
Down arrow
Left arrow
Right arrow
Move Enter
PgUp key
PgDn key
+ Key
- Key
Esc key
F1 key
F5 key
F7 key
F10 key
Function
Move to previous item
Move to next item
Move to the item on the left (menu bar)
Move to the item on the right (menu bar)
Move to the item you desired
Increas e the numeric val ue or make c hanges
Decrease the numeric value or make changes
Increas e the numeric val ue or make c hanges
Decrease the numeric value or make changes
Main Menu – Quit and not s ave c hanges into CMOS
Status Page Setup Menu and Option Page Setup Menu – Exit
Current page and r eturn to M ain Menu
General help on Setup navigation keys
Load pr evious values from CMOS
Load the opti mized defaults
Save all the CMOS c hanges and exit
2
P4M890-M7 SE
1 Main Menu
Once you enter Phoenix-Award BIOS™ CMOS Setup Utility, the Main Menu
will appear on the screen. The Main Menu allows you to select from several
setup functions. Use the arrow keys to select among the items and press <Enter>
to accept and enter the sub-menu.
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described in
this manual (Figure 1, 2, 3, 4, 5, 6, 7, 8, 9) is for your
reference only. The actual BIOS information and settings on
board may be slightly different from this manual.
„ Figure 1: Main Menu
Standard CMOS Features
This submenu contains industry standard configurable options.
Advanced BIOS Features
This submenu allows you to configure advanced features of the BIOS.
3
P4M890-M7 SE
Advanced Chipset Features
This submenu allows you to configure special chipset features.
Integrated Peripherals
This submenu allows you to configure cert ain IDE hard drive options and
Programmed Input/ Output features.
Power Management Setup
This submenu allows you to configure the power managem ent features.
PnP/PCI Configurations
This submenu allows you to configure cert ain “ Plug and Play” and PCI options.
PC Health Status
This submenu allows you to monitor the hardware of your system.
Performance Booster Zone
This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock.
(However, we suggest you to use the default setting. Changing the voltage and
clock improperly may damage the CPU or M/B!)
Load Optimized Defaults
This selection allows you to reload the BIOS when problem occurs during
system booting sequence. These configurations are factory settings optimized
for this system. A confirmation message will be displayed before defaults are
set.
4
P4M890-M7 SE
Set Supervisor Password
Setting the supervisor password will prohibit everyone except the supervisor
from making changes using the CMOS Setup Utility. You will be prompted with
to enter a password.
Set User Password
If the Supervisor Password is not set, then the User Password will function in
the same way as the Supervisor Password. If the Supervisor Password is set and
the User Password is set, the “User” will only be able to view configurations but
will not be able to change them.
Save & Exit Setup
Save all configuration changes to CMOS (memory) and exit setup. Confirmation
message will be displayed before proceeding.
Exit Without Sa ving
Abandon all changes made during the current session and exit setup.
Confirmation message will be displayed before proceeding.
5
P4M890-M7 SE
Upgrade BIOS
This submenu allows you to upgrade bios.
6
P4M890-M7 SE
2 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categori es.
Each category includes no, one or more than one setup items. Use the arrow
keys to highlight the item and then use the<PgUp> or <PgDn> keys to select the
value you want in each item.
„ Figure 2: Standard CMOS Setup
Main Menu Selections
This table shows the items and the available options on the Main Menu.
Item
Options
Description
Date
mm : dd : yy
Set the system date. Note
that the ‘Day ’ automatically
changes when you set the
date.
Time
hh : mm : ss
Set the system internal
clock.
IDE Channel 0 Master
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options
IDE Channel 0 Slav e
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
7
P4M890-M7 SE
Item
Options
Description
IDE Channel 1 Master
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
IDE Channel 1 Slav e
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
360K, 5.25 in
1.2M, 5.25 in
Driv e A
720K, 3.5 in
Driv e B
1.44M, 3.5 in
Select the ty pe of f loppy
disk drive installed in your
sy stem.
2.88M, 3.5 in
None
All Errors
No Errors
Halt On
All, but Key board
All, but Diskette
Select the situation in which
y ou want the BIOS to stop
the POST process and
notify y ou.
All, but Disk/ Key
Base Memory
N/A
Displays the amount of
conv entional memory
detected during boot up.
Extended Memory
N/A
Displays the amount of
extended memory detected
during boot up.
Total Memory
N/A
Displays the total memory
av ailable in the system.
8
P4M890-M7 SE
3 Advanced BIOS Features
„ Figure 3: Advanced BIOS Setup
Boot Seq & Floppy Setup
This item allows you to setup boot sequence & Floppy.
9
P4M890-M7 SE
Hard Disk Boot Priority
The BIOS will attempt to arrange the Hard Disk boot sequence automatically.
You can change the Hard Disk booting sequence here.
The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USB HDD0, USB
HDD1, USB HDD2, and Bootable Add-in Cards.
First/Second/Third Boot Dev ice
The BIOS will attempt to load the operating system in this order.
The Choices: Floppy, LS120, Hard Disk, CDROM, ZIP 100, USB-FDD,
USB-ZIP , USB-CDROM, LAN, Disabled.
Boot Other Dev ice
When enabled, BIOS will try to load the operating system from other device
when it failed to load from the three devices above.
The Choices: Enabled (default), Disabled
Sw ap Floppy Drive
For systems with two floppy drives, this option allows you to swap logical
drive assignments.
The Choices: Disabled (default), Enabled.
10
P4M890-M7 SE
Boot Up Floppy Seek
When enabled, System will test the floppy drives to determine if they have 40
or 80 tracks during boot up. Disabling this option reduces the time it takes to
boot-up.
The Choices: Enabled (default), Disabled.
Shadow Setup
„
This item allows you to setup cache & shadow setup.
Figure 3.2: Shadow Setup
Video BIOS Shadow
Determines whether video BIOS will be copied to RAM for faster execution or
not.
Enabled (default) Optional ROM is enabled.
Disabled Optional ROM is disabled.
11
P4M890-M7 SE
Cache Setup
CPU L1 & L2 Cache
Depending on the CP U/chipset in use, you may be able to increase me mory
access time with this option.
Enabled (default) Enable cache.
Disabled
Disable cache.
CPU L3 Cache
Depending on the CP U/chipset in use, you may be able to increase me mory
access time with this option.
Enabled (default) Enable cache.
Disabled
Disable cache.
CPU L2 Cache ECC Checking
This item allows you to enable/disable CPU L2 Cache ECC Checking.
The Choices: Enabled (default), Disabled.
12
P4M890-M7 SE
CPU Feature
Delay Prior to Thermal
Set this item to enable the CP U Thermal function to engage after the specified
time.
The Choices: 4 Min, 8 Min, 16Min (default), 32 Min.
Thermal Management
This option allows you to select the way to control the “ Thermal Management.”
The Choices: Thermal Monitor 1 (default), Thermal Monitor 2.
TM2 Bus Ratio
This option represents the frequency (bus ratio) of the throttled performance
state that will be initiated when the on-die sensor detects temperature increase.
Min=
0
Max= 255
Key in a DEC number.
The Choices: 0 X (default)
TM2 Bus VID
This option represents the voltage of the throttled performance state that will be
initiated when the on-die sensor detects temperature increase.
The Choices: 0.8375V (default), 0.8375-1.6000.
13
P4M890-M7 SE
Limit CPUID MaxVal
Set Limit CP UID MaxVal to 3, it should be “ Disabled” for Windows XP .
The Choices: Disabled (default), Enabled.
C1E Function
This item allows you to configure the Enhanced Halt State (C1E) function,
which may reduce the power consumption of your system when the system is
idle.
The Choices: Auto (default),Disabled.
Execute Disable Bit
This item allows you to configure the Execute Disabled Bit function, which
protects your system from buffer overflow attacks.
The Choices: Enabled (default), Disabled.
Virtualization Technology
Virtualization Technology can virtually separate your system resource into
several parts, thus enhance the performance when running virtual machines or
multi interface systems.
The Choices: Enabled (default), Disabled.
Virus Warning
This option allows you to choose the VIRUS Warning feature that is used to
protect the IDE Hard Disk boot sector. If this function is enabled and an attempt
is made to write to the boot sector, BIOS will display a warning message on the
screen and sound an alarm beep.
Disabled (default) Virus protection is disabled.
Enabled
Virus protection is activated.
Hyper-Threading Technology
This option allows you to enable or disabled Hyper-Threading Technology.
“ Enabled” for Windows XP and Linux 2.4.x (OS optimized for
Hyper-Threading Technology). “ Disable” for other OS (OS not optimized for
Hyper-Threading Technology).
The Choices: Enabled (default), Disabled.
14
P4M890-M7 SE
Quick Power On Self Test
Enabling this option will cause an abridged version of the Power On Self-Test
(POST) to execute after you power up the computer.
Disabled
Normal POST.
Enabled (default) Enable quick POST.
Boot Up NumLock Status
Selects the NumLock State after the system switched on.
The Choices:
On (default) Numpad is number keys.
Off
Numpad is arrow keys.
Typematic Rate Setting
When a key is held down, the keystroke will repeat at a rate determined by the
keyboard controller. When enabled, the typematic rate and typematic delay can
be configured.
The Choices: Disabled (default), Enabled.
Typematic Rate (Chars/Sec)
Sets the rate at which a keystroke is repeated when you hold the key down.
The Choices: 6 (default), 8, 10, 12, 15, 20, 24, 30.
Typematic Dela y (Msec)
Sets the delay time after the key is held down before it begins to repeat the
keystroke.
The Choices: 250 (default), 500, 750, 1000.
Security Option
This option will enable only individuals with passwords to bring the system
online and/or to use the CMOS Setup Utility.
System:
A password is required for the system to boot and is also
required to access the Setup Utility.
Setup (default):
A password is required to access the Setup Utility only.
This will only apply if passwords are set from the Setup main menu.
15
P4M890-M7 SE
MPS Version Control For OS
The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor speci fication.
Select version supported by the operation system running on this computer.
The Choices: 1.4 (default), 1.1.
OS Select For DRAM > 64MB
A choice other than Non-OS2 is only used for OS2 systems with memory
exceeding 64MB.
The Choices: Non-OS2 (default), OS2.
HDD S.M.A.R.T. Capability
This item allows you to enable/disable HDD S.M.A.R.T. Capability.
The Choices: Disabled (default), Enabled.
Small Logo(EPA) Show
This item allows you to select whether the “Small Logo” shows. Enabled
(default) “ Small Logo” shows when system boots up. Disabled No “Small
Logo” shows when system boots
The Choices: Enabled (default), Disabled
Summary Screen Show
This item allows you to enable/disable the summary screen.
means system configuration and PCI device listing.
The Choices: Disabled (default), Enabled.
16
Summary screen
P4M890-M7 SE
4 Advanced Chipset Features
„
This submenu allows you to configure the speci fic features of the chipset
installed on your system. This chipset manage bus speeds and access to system
memory resources, such as DRAM. It also coordinates communications with the
PCI bus. The default settings that came with your system have been optimized
and therefore should not be changed unless you are suspicious that the settings
have been changed incorrectly.
Figure 4: Advanced Chipset Setup
17
P4M890-M7 SE
AGP & P2P Bridge Control
Highlight “Press Enter” next to the “ AGP & P2P Bridge Control” label and
pressing the enter key will take you a submenu with the following options:
„ Figure 4.1:
AGP & P2P Bridge Control
AGP Aperture Size
Select the size of the Accelerated Graphics Port (AGP ) aperture. The aperture
is a portion of the P CI memory address range dedicated for graphics memory
address space. Host cycles that hit the aperture range are forwarded to the AGP
without the need of translation.
The Choices: 32M, 64M, 128M (default), 256M.
AGP 2.0 Mode
This item allows you to select the AGP Mode.
The Choices: 8X (default), 4X.
AGP Master 1 WS Write
When enabled, writes to the AGP (Accelerated Graphics P ort) are executed
with one wait states.
The Choices: Enabled (default), Disabled.
18
P4M890-M7 SE
AGP Master 1 WS Read
When enabled, read to the AGP (Accelerated Graphics P ort) are executed with
one wait states.
The Choices: Enabled (default), Disabled.
VGA Share Memory Size
This item allows you to select the VGA share memory size.
The Choices: 64M (default), 16M, 32M, 128M, 256M, Disabled
Direct Frame Buffer
This item allows you to disabled or enabled direct frame buffer
The Choices: Enabled (default), Disabled.
CPU & PCI Bus Control
By highlighting the “Press Enter” label next to the “CPU & PCI Bus Control”
and press the enter key, it will take you a submenu with the following options:
„ Figure 4.2: CPU & PCI Bus Control
PCI Master 0 WS Write
When enabled, writes to the P CI bus are executed with zero-wait states.
The Choices: Enabled (default), Disabled.
19
P4M890-M7 SE
PCI Delay Transaction
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with P CI
specification.
The Choices: Enabled (default), Disabled.
Vlink mode selection
This item allows you to select Vlink mode.
The Choices: B y Auto (default), Mode 0 , Mode 1.
VLink 8X Support
This item allows you to enable or disable VLink 8X support.
The Choices: Enabled (default), Disabled.
VIA PWR Management
The Choices: Enabled (default), Disabled.
Memory Hole
You can reserve this area of system memory for ISA adapter ROM. When this
area is reserved it cannot be cached. Check the user information of peripherals
that need to use this area of system memory for the memory requirements.
The Choices: Disabled (default), Enabled.
System BIOS Cacheable
Selecting the “ Enabled” option allows caching of the system BIOS ROM at
F0000h-FFFFFh, which is able to improve the system performance. However,
any programs that attempts to write to this memory block will cause conflicts
and result in system errors.
The Choices: Enabled (default), Disabled.
Top Performance
The Choices: Disabled (default), Enabled.
20
P4M890-M7 SE
5 Integrated Peripherals
„ Figure 5. Integrated Peripherals
VIA OnChip IDE Device
Highlight the “Press Enter” label next to the “ VIA OnChip IDE Device” label
and press enter key will take you a submenu with the following options:
21
P4M890-M7 SE
SATA Controller
This option allows you to enable the on-chip Serial ATA.
The Choices: Enabled (default), Disabled.
SATA Controller Mode
This option allows you to select SATA Mode.
The Choices: RAID, IDE (default).
IDE DMA Transfer Access
This item allows you to enable or disable the IDE DMA transfer access.
The Choices: Enabled (default), Disabled.
On-chip IDE Channel 0/1
The motherboard chipset contains a P CI IDE interface with support for two
IDE channels. Select “ Enabled” to activate the first and/or second IDE interface.
Select “ Disabled” to deactivate an interface if you are going to install a primary
and/or secondary add-in IDE interface.
The Choices: Enabled (default), Disabled.
IDE Prefetch Mode
The “ onboard” IDE drive interfaces supports IDE prefetch function for faster
drive access. If the interface on your drive does not support prefetching, or if
you install a primary and/or secondary add-in IDE interface, set this option to
“ Disabled”.
The Choices: Enabled (default), Disabled.
Primary/Secondary/Master/Slave PIO
The IDE P IO (P rogrammed Input / Output) fields let you set a P IO mode (0-4)
for each of the IDE devices that the onboard IDE interface supports. Modes 0
to 4 will increase performance progressively. In Auto mode, the system
automatically determines the best mode for each device.
The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4.
22
P4M890-M7 SE
Primary/Secondary/Master/Slave UDMA
Ultra DMA function can be implemented if it is supported by the IDE hard
drives in your system. As well, your operating environment requires a DMA
driver (Windows 95 or OSR2may need a third party IDE bus master driver). If
your hard drive and your system software both support Ultra DMA, select Auto
to enable BIOS support.
The Choices: Auto (default), Disabled.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple
sectors read / write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block mode (most new drives do), select Enabled for automatic detection of the
optimal number of block read / write per sector where the drive can support.
The Choices: Enabled (default), Disabled.
VIA OnChip PCI Device
„
Highlight the “Press Enter” label next to the “ VIA OnChip PCI Device” label
and press the enter key will take you a submenu with the following options:
Figure 5.2: VIA OnChip PCI Device
Azalia HDA Controller
This option allows you to control the onboard HD audio.
The Choices: Auto (default), Disabled.
23
P4M890-M7 SE
LAN Controller
This option allows you to control the onboard LAN.
The Choices: Enabled (default), Disabled
Lan Boot ROM
Decide whether to invoke the boot ROM of the onboard LAN chip.
The Choices: Disable (default), Enabled.
Super IO Device
Press Enter to configure the Super I/O Device.
Onboard FDC Controller
Select enabled if your system has a floppy disk controller (FDC) installed on
the system board and you wish to use it. If you installed another FDC or the
system uses no floppy drive, select disabled in this field.
The Choices: Enabled (default), Disabled.
Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial
ports.
The Choices: 3F8/IRQ4 (default), Disabled, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,
Auto.
24
P4M890-M7 SE
Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with
which I/O Address.
The Choices: 378/IRQ 7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.
Parallel Port Mode
This item allows you to determine how the parallel port should function. The
default value is SPP .
The Choices:
SPP (de fault)
Using P arallel port as Standard P rinter Port.
EPP
Using P arallel P ort as Enhanced P arallel Port.
ECP
Using P arallel port as Extended Capabilities P ort.
ECP +EPP
Using P arallel port as ECP & EPP mode.
ECP Mode Use DMA
Select a DMA Channel for the port.
The Choices: 3 (default), 1.
USB De vice Setting
Press Enter to configure the USB Device.
25
P4M890-M7 SE
USB 1.0/2.0 Controller
These options allow you to enable or disable the USB 1.0/2.0 controller
function.
The Choices: Enabled (default), Disabled.
USB Operation Mode
This option let you select the operation mode of USB function.
The Choices: High Speed (default), Full/Low Speed.
USB Keyboard/Mouse/Storage Function
These options allow you to enable or disable the USB keyboard/mouse/storage
devices.
The Choices: Enabled (default), Disabled.
USB Mass Storage Dev ice Boot Setting
These options allow you to choose the boot up type of the USB mass storage
devices..
The Choices: Auto mode (default), FDD mode, HDD mode.
26
P4M890-M7 SE
6 Power Management Setup
The Power Management Setup Menu allows you to configure your system to
utilize energy conservation and power up/power down features.
„ Figure 6. Power Management Setup
ACPI Function
This item displays the status of the Advanced Configuration and Power
Management (ACPI).
The Choices: Enabled (default), Disabled.
27
P4M890-M7 SE
Power Management
This category allows you to select the power saving method and is directly
related to the following modes:
1. HDD Power Down.
2. Suspend Mode.
There are three options of Power Management, three of which have fixed mode
settings
Min. Power Saving
Minimum power management.
Suspend Mode = 1 hr.
HDD Power Down = 15 min
Max. Power Saving
Maximum power management only available for sl CPU’s.
Suspend Mode = 1 min.
HDD Power Down = 1 min.
User Define (default)
Allow you to set each option individually.
When you choose user define, you can adjust each of the item from 1 min. to 1
hr. except for HDD Power Down which ranges from 1 min. to 15 min.
HDD Power Down
When enabled, the hard-disk drives will power down after a set time of system
inactivity. All other devices remain active.
The Choices: Disabled (default), 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7
Min, 8 Min, 9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15Min.
Suspend Mode
The item allows you to adjust the system idle time before suspend.
The Choices: Disabled (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min,
20 Min, 30 Min, 40 Min, 1 Hour.
Video Off Option
This field determines when to activate the video off feature for monitor power
management.
The Choices: Suspend→Off (default), Always on.
28
P4M890-M7 SE
Video Off Method
This option determines the manner when the monitor goes blank.
V/H SYNC+Blank (default)
This selection will cause the system to turn off the vertical and horizontal
synchronization ports and write blanks to the video buffer.
Blank Screen
This option only writes blanks to the video buffer.
DPMS
Initial display power management signaling.
Modem Use IRQ
This determines the IRQ, which can be applied in MODEM use.
The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA.
Soft-Off by PWRBTN
This item determines the behavior of system power button. Instant off turn off
the power immediately, and Delay 4 Sec. will require you to press and hold the
power button for 4 seconds to cut off the system power.
The Choices: Delay 4 Sec, Instant-Off (default).
Ac Loss Auto Restart
This setting specifies how your system should behave aft er a power fail or
interrupts occurs. By choosing off will leave the computer in the power off stat e.
Choosing On will reboot the computer. Former-Sts will restore the system to the
status before power failure or interrupt occurs.
The Choices: Off (default), On, Former-Sts.
HPET Support
This option allows you to disabled or enables the High Precision Event Timer.
The Choices: Enabled (default), Disabled.
HPET Mode
This option allows you to select the modes of the High Precision Event Timer.
The Choices: 32-bit mode (default), 64-bit mode.
29
P4M890-M7 SE
WDRT Support
This option allows you to disabled or enables the Watchdog Timer.
The Choices: Enabled (default), Disabled.
WDRT Run/Stop
This option allows you to select the mode of Watchdog Timer.
The Choices: Stop (default), Run.
WDRT Count
This option allows you to control the count of the Watchdog Timer.
The Choices: 1023 (default); min=0, amx=1023, key in a DEC number.
Wakeup Event Detect
Figure 6.1:IRQ/Event Activity Detect
Highlight the “Press Enter” label next to the “ IRQ/Event Activity Detect” label
and press the enter key will take you a submenu with the following options:
30
P4M890-M7 SE
PowerOn by PCI Card
When you select Enabled, a P ME signal from P CI card returns the system to
Full ON state.
For this function to work, you may need a LAN add-on card which supports the
Wake on LAN function. Set the Wake on LAN (WOL) jumper on motherboard
to enable if applicable.
The Choices: Disabled (default), Enabled.
Modem Ring Resume
This item allows you to disable or enable Modem Ring Resume function.
The Choices: Disabled (default), Enabled.
RTC Alarm Resume
When “ Enabled”, you can set the date and time at which the RTC (real-time
clock) alarm awakens the system fro m Suspend mode.
The Choices: Disabled (default), Enabled.
Date (of Month)
You can choose which month the system will boot up. This field is only
configurable when “ RTC Resume” is set to “ Enabled”.
Resume Time (hh:mm:ss)
You can choose the hour, minute and second the system will boot up. This field
is only configurable when “ RTC Resume” is set to “ Enabled”.
31
P4M890-M7 SE
7 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal
Computer Interconnect, is a system which allows I/O devices to operate at
speeds nearing the speed of the CPU itself uses when communicating with its
own special components. This section covers some very techni cal items and it is
strongly recommended that only experienced users should make any changes to
the default settings.
„
Figure 7: PnP/PCI Configurations
PNP OS Installed
When set to YES, BIOS will only initialize the PnP cards used for the boot
sequence (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP
operating system like Window™ 95. When set to NO, BIOS will initialize all
the PnP cards. For non-PnP operating systems (DOS, Netware™), this option
must set to NO.
The Choices: No (default), Yes.
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip VGA first.
The Choices: PCIEx (default), PCI Slot, Onboard, AGP.
32
P4M890-M7 SE
Reset Configuration Data
The system BIOS supports the PnP feature which requires the system to record
which resources are assigned and protects resources from conflict.
Every peripheral device has a node, which is called ESCD. This node records
which resources are assigned to it. The system needs to record and update ESCD
to the memory locations. These locations are reserved in the system BIOS. If the
Disabled (default) option is chosen, the system‘s ESCD will update only when
the new configuration varies from the last one. If the Enabled option is chosen,
the system is forced to update ESCDs and then is automatically set to the
“ Disabled” mode.
The above settings will be shown on the screen only if “ Manual” is chosen for
the resources controlled by function.
Legacy is the term, which signifies that a resource is assigned to the ISA Bus
and provides non-PnP ISA add-on cards. PCI / ISA PnP signify that a resource
is assigned to the PCI Bus or provides for ISA PnP add-on cards and
peripherals.
The Choices: Disabled (default), Enabled.
Resources Controlled By
By Choosing “Auto(ESCD)” (default), the system BIOS will detect the system
resources and automatically assign the relative IRQ and DMA channel for each
peripheral. By Choosing “Manual”, the user will need to assign IRQ & DMA for
add-on cards. Be sure that there are no IRQ/DMA and I/O port conflicts.
The Choices: Auto (ESCD) (default), Manual.
33
P4M890-M7 SE
IRQ Resources
This submenu will allow you to assign each system interrupt a type, depending
on the type of device using the interrupt. When you press the “ Press Enter” tag,
you will be directed to a submenu that will allow you to configure the system
interrupts. This is only configurable when “ Resources Controlled By” is set to
“Manual”.
IRQ-3
assigned to PCI Device
IRQ-4
assigned to PCI Device
IRQ-5
assigned to PCI Device
IRQ-7
assigned to PCI Device
IRQ-9
assigned to PCI Device
IRQ-10
assigned to PCI Device
IRQ-11
assigned to PCI Device
IRQ-12
assigned to PCI Device
IRQ-14
assigned to PCI Device
IRQ-15
assigned to PCI Device
PCI / VGA Palette Snoop
Some old graphic controllers need to “ snoop” on the VGA palette and then map
it to their display as a way to provide boot inform ation and VGA compatibility.
This item allows such snooping to take place.
The Choices: Disabled (default), Enabled
Assign IRQ For VGA
This item allows the users to choose which IRQ to assign for the VGA.
The Choices: Enabled (default), Disabled.
Assign IRQ For USB
This item allows the users to choose which IRQ to assign for the USB.
The Choices: Enabled (default), Disabled.
Maximum Payload Size
Set the maximum payload size for Transaction packets (TLP).
The Choice: 4096 (default.), 128, 256, 512, 1024, 2048.
34
P4M890-M7 SE
8 PC Health Status
„ Figure 8: PC Health Status
Shutdown Temperature
This item allows you to set up the CPU shutdown Temperature. This item is
only effective under Windows 98 ACPI mode.
The Choices: 65℃/ 149℉, 70℃/ 158℉, 75℃/ 167℉, 80℃/ 176℉, 85℃/ 185
℉, 90℃/ 167℉, 95℃/ 194℉(default), Disabled.
CPU FAN Control by
Choose “ smart” to reduce the noise caused by CPU FAN.
The Choices: Smart, Always On (default).
CPU Fan Load (Sharp=0)
The Choices: Min=0, Max=7; key in a DEC number.
CPU Fan Start (℃)
CPU fan starts to work under smart fan function when arrive this set value.
The Choices: Min=0, Max=100; key in a DEC number.
35
P4M890-M7 SE
CPU Fan Full speed <℃>
When CPU temperature is reach the set value, the CPU fan will work under Full
Speed.
The Choices: Min=0, Max=100; key in a DEC number.
Start PWM Value (%)
When CPU temperature arrives to the set value, the CPU fan will work under
Smart Fan Function mode. The range is from 0~127, with an interval of 1.
The Choices: Min=0, Max=100; key in a DEC number.
Slope PWM Level (%/℃)
Increasing the value of slope PWM will raise the speed of CPU fan.
The Choices: 3.1%/℃ Medium(default), 0.0%/℃, 0.8%/℃, 1.6%/℃,6.3%/℃
High,12.5%/℃, 25.0%/℃, 50.0%/℃.
CPU Vcore, NB Vcore, +3.3V, +5.0V, +12V, DRAM Voltage,
VTT Voltage, Voltage Battery
Detect the system’s voltage status automatically.
Current CPU Temp
This field displays the current temperature of CPU.
Current CPU FAN Speed
This field displays the current speed of CPU fan.
Current SYS FAN Speed
This field displays the current speed SYSTEM fan.
Show H/W Monitor in POST
If you computer contains a monitoring system, it will show PC health status
during POST stage. The item offers several different delay times.
The Choices: Enabled (default), Disabled.
36
P4M890-M7 SE
9 Performance Booster Zone
„
Figure 9: Performance Booster Zone
DRAM Clock/Drive Control
„
This item controls the DRAM Clock. Highlight “Press Enter” next to the
“ DRAM Clock/Drive Control” label and pressing the enter key will take you a
submenu with the following options:
Figure 9.1: DRAM Clock/Drive Control
37
P4M890-M7 SE
DRAM Clock
This item determines DRAM clock.
The Choices: B y SPD (default), 100MHz, 133MHz, 166MHz, 200MHz,
266MHz, 333MHz .
DRAM Timing
This item determines DRAM clock/ timing.
The Choices: Auto by SPD (default), Manual, Turbo, Ultra.
SDRAM CAS Latency
When DRAM is installed, the number of clock cycles of CAS latency depends
on the DRAM timing.
The Choices: 2.5 /4(default).
Bank Interleave
This item allows you to enable or disable the bank interleave feature.
The Choices: Disabled (default).
Precharge to Active (tRP)
This item allows you to specify the delay from precharge command to activate
command.
The Choices: 4T (default).
Activ e to Precharge (tRAS)
This item allows you to specify the minimum row active time (tRAS).
The Choices: 07T (default).
Activ e to CMD (tRCD)
Use this item to specify the delay from the activation of a bank to the time that
a read or write command is accepted.
The Choices: 4T (default).
REF to ACT/REF to REF (Trfc)
This item allows you to determine the selection for REF to ACT/REF to REF
(tRFC).
The Choices: 20T/21T (default).
38
P4M890-M7 SE
ACT (0) to ACT (1) (tRRD)
This item allows you to determine the selection for ACT (0) to ACT (1) (tRRD)
The Choices: 3T (default).
1T CMD Support
The Choices: Disable (default), Auto.
DDR2 On Die Termination
This option allows you to choose the working type of ODT.
The Choices: ODT Always ON (default), Dynamic ODT, ODT Always OFF.
CPU CLOCK
This item allows you to select CPU Clock, and CPU over clocking.
Special Notice:
If the system’s frequency that you are selected is not functioning, there are two
methods of booting-up the system.
Method 1:
Clear the COMS data by setting the JCOMS1 ((2-3) closed)) as “ ON” status. All
the CMOS data will be loaded as defaults setting.
Method 2:
Press the <Insert> key and Power button simultaneously, after that keep-on
pressing the <Insert> key until the power-on screen showed.
This action will boot-up the system according to FSB of the processor
It’s strongly recommended to set CPU Vcore and clock in default setting. If the
CPU Vcore and clock are not in default setting, it may cause CPU or M/B
damage.
The Choices: 100MHz(default); Min=100, Max=400, key in a DEC number.
Async PCIE CLOCK
This item allows you to select Async PCIE clock.
Min= 100 Max=150 Key in a DEC number.
The Choices: 100MHz(default) ; Min=100, Max=150, key in a DEC number.
CPU Clock Ratio
This item allows you to select the CPU Ratio.
Min= 6 Max= 50 Key in a DEC number.
The Choices: 6X (default).
39
P4M890-M7 SE
Spread Spectrum
This item allows you to enable/disable the Spread Spectrum function.
The Choices:+/- 0.25% (default), +/- 0. 5%, Disabled, -0.5%, -1.0%.
DDR Voltage
This item allows you to select DDR Voltage.
The Choices: StartUp (default), +0.10V, +0.20V, +0.30V, +0.40V, +0.50V,
+0.60V, +0.70V.
CPU Voltage
This item allows you to select CPU Voltage.
The Choices: StartUp (default), +0.012V~+0.787V.
40
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising