Rack PDUs
Emerson Network Power Rack PDUs
This is how you can benefit from Emerson Network Power Rack PDUs
Featuring High Availability
Emerson Network Power rack PDUs are especially designed to
provide maximum power densities and high temperature stability
commonly required in modern data center racks. The system was
developed to optimize basic availability of the power supply, minimizing
downtimes as PDUs can be expanded easily. Additionally, Emerson
Network Power offers requisite support enabling you to fulfill your
service-level agreements.
High temperature stability
Modular hot-swap-enabled communications card
Hydraulic-magnetic circuit breaker
MPX™ rack PDU featuring an adaptive,
modular system design
Bistable / normally closed relay
Optimized Energy and Capacity Management
Thanks to highly accurate and comprehensive energy metering of
the entire system up to the connection level. The superior visibility
delivered by the MPX and MPH2™ rack PDUs for monitoring the
energy consumption of your IT equipment enables you to scale your
energy-consumption infrastructure and avoid unnecessary costs.
These rack PDUs feature the lowest energy consumption in their class.
Essential electrical parameters metered with an
accuracy of ±1 %
Lowest PDU power consumption of all switched
rack PDUs in the industry
Reports are compiled using a variety of Emerson
Network Power DCIM solutions
Simplified Integration into Management Tools
MPX and MPH2 rack PDUs offer a simplified approach to
implementation and change management that translates to real
cost savings and operational advantages. These rack PDUs support
all conventional management, authentication and encryption standards
and protocols, allowing for integration into industry-leading Kernelbased Virtual Machine (KVM) systems, serial consoles and Emerson
Network Power infrastructure management systems. Furthermore,
MPX and MPH2 integrate the rack PDU monitoring and environment
information at rack level in the superordinate data-center management
software provided by Emerson Network Power or a third party.
Up to four PDUs with one IP address within
one Rack PDU Array™
Integrated into KVM, serial consoles and
infrastructure management appliances; integrated
in Emerson Network Power software stack
IPv6 support
Remote authentication protocol support (LDAP,
Active Directory, Radius, Kerberos, TACACS+)
and encryption
Simpler Physical and Electrical Installation
Emerson Network Power rack PDUs are easy to install and use in
trade-standard racks. The rack PDUs can be delivered pre-installed
in purchased Emerson Network Power racks, saving time and money.
Many important global power networks commonly used in data centers
or remote locations are available – an Emerson Network Power expert
can help you choose the right rack PDU to meet your needs.
Special tool-less Knürr DCM rack fixture
Can be pre-installed in Emerson Network Power
rack solutions.
Available in standard voltage / current strength
combinations
Rack PDUs | 203
Emerson Network Power Rack PDUs
Emerson Network Power Rack PDUs Europe
Product Series Overview
Overview: Emerson Network Power Rack PDUs Europe
MPX - Adaptive Rack PDU
Features
MPX-R
MPX-B
MPH2 - Managed Rack PDU
MPX-E
DI-STRIP Basic Rack PDU
MPH2-R
MPH2-M
MPH2-C
MPH2-B
DI-STRIP RM
DI-STRIP M
DI-STRIP E
Modular
Local display
*
Remote
interface
*
Metering
per phase
*
Metering
per group
Metering
per output
Switch
per output
Metering
parameter
Input power
Outputs
A, V, W, kWh,
VA, Hz,
power factor
crest factor
A, V, W, kWh,
VA, Hz,
power factor
A, V, W, kWh,
Hz
A, V, W, kWh,
VA, Hz,
power factor
crest factor
A, V, W, kWh,
VA, Hz,
power factor
crest factor
A, V, W, kWh,
VA, Hz,
power factor
A, V, W, kWh,
VA, Hz,
power factor
A
A
1ph + 3ph
max 63A
1ph + 3ph
max 63A
1ph + 3ph
max 63A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
IEC C13&C19
Schuko
IEC C13&C19
Schuko
IEC C13&C19
Schuko
Switzerland
GST18
IEC C13&C19
IEC C13&C19
IEC C13&C19
IEC C13&C19
IEC C13&C19
Schuko
Switzerland
France
IEC C13&C19
Schuko
Switzerland
France
IEC C13&C19
Schuko
Switzerland
France
Sensor connections
MPX and MPH2 accessories are similar,
simplifying installation.
* Only with MPX-PEM monitored
204 | Rack PDUs
*
MPX™
MPX™ – Adaptive Rack PDU
Respond to change and maximize profits
No-one can make definite predictions about the power-supply demands the future will bring. But one thing is certain: the versatile, adaptive MPX rack PDUs equip you with the wherewithal to face all eventualities. They enable
you to react quickly to changes in rack equipment and provide dynamic capacities, offering:
Modular hot-swap-enabled output power
Modular hot-swap-enabled communication
Modular input power.
Benefits of MPX
Adaptive capacity, distribution,
monitoring, control and administration of critical equipment.
Flexibility in reacting to constant
changes – modules can be regrouped
to accommodate altered requirements.
Only purchase what you really need
and utilize existing investments.
Reliable communication.
Developed for critical environments
Critical rack operating temperature – of up to 60° C suitable for high
temperatures inside racks.
Accurate voltage and current metering with tolerances of ±1 % offer a
comprehensive overview.
Energy and power metered with outstanding precision all the way through
to output level.
Extensive alert function; including notification before failure occurs.
Monitoring of environment conditions including alerts and alarms.
Notification upon failure or if individual components are removed.
Flexible, configurable input and
output distribution
The scalable design of the MPX rack
PDU allows on-site configuration that
meets the current requirements of the
IT equipment. It is the perfect solution
for coping with the ever increasing demands of expanding data centers. You
can set up your IT equipment at another location or add new components
to extend your environment. All you
need to do in this case is simply reconfigure the power supply and the power
distribution.
Hot-swap-enabled
output module
Simple
implementation for
quick start-up of IT
equipment.
Equipped to face the demands of
today and tomorrow
The MPX rack PDU supports a variety of
configurations for single-phase and
three-phase power inputs enabling
changes while retaining the distribution infrastructure.
Outputs and
modules
Outputs can be
controlled and measured
remotely thereby
increasing flexibility and
on-site security.
Modular input power.
Can be reconfigured for altered power demands; single-phase and three-phase input.
Module can be fitted on top or at the bottom.
Rack PDUs | 205
MPX™
MPX™
Benefits of the modular MPX rack PDU
INPUT POWER
Configurable: 20 to 60 A (USA);
16 to 63 A (EU).
Single-phase and three-phase.
Cable routing possible from
above and below.
OUTPUT DISTRIBUTOR
Scalable, combination-compatible
and can be replaced during
operation
Single-phase NEMA 5-20R, IEC-C13,
IEC-C19, Schuko, Switzerland,
GST18.
Load balance.
MODULARITY
Input modules.
Output modules.
External display.
External sensors.
RPC2 communication card.
MONITORING
Three levels: Input level,
module level, output level.
Temperature and humidity.
Door contacts and floating break
input contacts.
REMOTE CONTROLLED SOCKETS
Socket level.
Featuring High Availability
Heat resistant up to 60° C ensuring reliable operation in the warm aisle.
Modular hot-swap-enabled output module, controller card and sensors;
can be exchanged or updated during operation.
Special switch relay (normally closed); connected servers have an
uninterrupted power supply even in the event of failure.
Redundant power supply for control electronics.
Fixed databus on the busbar.
Complete data tapping on the Power Entry Module (PEM) (without any
additional external monitoring devices).
Proactive alert by additional metering of the neutral conductor and
crest factor (assessment of network quality facilitating early detection of
power-supply unit failures).
Maximum Flexibility and Scalability
All modules configured in line with requirements (patented quick-mount
fitting for safe installation).
One busbar for different networks and power levels – input module can
be freely selected. All other components are "hot-swap-enabled" when
running operation.
Mobile display for reading all MPX data on the rack.
Optical slot-space display (easy server slot-space identification at the push
of a button).
Highest Possible Power Levels in all Areas
Power feed of max. 3 x 63 A; optimal for Blade server applications.
Only one IP address for up to 4 rails with 24 modules.
Plug and Play for numerous sensors.
Extensive monitoring with a metering accuracy of ±1 % right through to
output level.
Module and sensor autodetect function with operating software.
Minimal power loss for MPX systems.
206 | Rack PDUs
MPX™
The busbar (MPX™ PRC):
Serves as power and communication
distribution for all supported
modules. Available in two heights to
accommodate different rack heights.
Output module (MPX™ BRM):
Provides overload protection by distributing power to individual
servers. Available functions: Elementary, Branch Metering and
Output Metering with switch function.
Power-rail spacer:
Reserves unused space until needed for
an MPX™ module.
BDM™ local display module
Extended diagnostic functionality;
customer-convenient display. Features
include detailed information about alerts
and specific labeling for outputs.
SN sensors:
Consolidates environmental monitoring of temperature,
humidity and potential-free input contacts with the power
supply at rack level.
Communication module (RPC2):
Input module (MPX™ PEM):
Routes the input power to the busbar system of the
Elementary model (without RPC2™) and the version with
input metering (includes pre-installed RPC2™).
Installed in the power input module and
offers an extendable interface for network
communication, sensors and the local
display.
Rack PDUs | 207
MPX™
MPX™
Four equipment models for different requirements
The MPX modular rack PDU consists
of various components. The basic
element is a busbar, which is responsible for the power and communication distribution to the individual
modules. The input power is routed
via the MPX Power Entry Module
(MPX PEM) to the MPX system.
Different output modules (MPX
Branch Receptacle Modules, MPX
BRM) are available depending on
requirements. Four different variants
can be set up depending on the component population of the busbars:
1. MPX Elementary
Modular basic power distribution without metering and control function. An
upgrade to another equipment model
is quick and easy.
2. MPX Elementary Phase
Monitored
Modular power distribution with metering on input. An upgrade to a superordinate line is possible by populating
with appropriate output modules.
3. Branch-Monitored MPX
Modular power distribution with metering on input and each output module.
An upgrade or downgrade to another
line is possible if installed with
appropriate output modules.
4. Receptacle Managed MPX
Modular power distribution with input,
metering, each output module and
each output. Individual outputs can
also be switched on and off remotely.
A downgrade to another line is possible
if installed with the appropriate output
modules.
A combination of the "Elementary
Phase Monitored", "Branch-Monitored"
and "Receptacle Managed" lines on a
shared busbar is also possible and is one
of the exceptional features of the MPX.
Interfaces for the network communication, sensors and/or local display are
provided by the Rack PDU Card (RPC)
in the MPX PEM. The RPC Card enables
connection to an optional RPC Basic
Display Module (RPC BDM) to display
local status and alerts.
Output module
Receptacle Managed
Busbar (MPXT PRC)
Distributes power and
communication signals
to all modules.
Branch-Monitored
output module
(MPX BRM)
Spacer for busbars
Fills unused gaps until a
Liebert MPX module is
upgraded.
Output module
e. g. Elementary
(MPX BRM)
Input module
(MPX PEM)
Routes input power and
data (depending on the
module type) to the
busbar system.
208 | Rack PDUs
MPX™
MPX™ – Configuration models in Europe
Four equipment models
Order number
Length 1035
MPXPRC-V1035XXX
Length 1880
MPXPRC-V1880XXX
3ph 16A fixed
Input Modules
3ph 32A fixed
3ph 63A fixed
Elementary
Output Modules
Branch-Monitored
Output Modules
Receptacle Managed
Output Modules
Sensors
External Display
MPX™
Receptacle Managed
MPXPEM-EHAEXQ30
MPXPEM-EHABXQ30
MPXPEM-EHAEXT30
MPXPEM-EHABXT30
MPXPEM-EHAEXR30
MPXPEM-EHABXR30
MPXPEM-EHBEXZ30
MPXPEM-EHBBXZ30
IEC-C13 L1
MPXBRM-EEBC7N1N
IEC-C13 L2
MPXBRM-EEBC7N2N
IEC-C13 L3
MPXBRM-EEBC7N3N
IEC-C19 L1
MPXBRM-EEBC4O1N
IEC-C19 L2
MPXBRM-EEBC4O2N
IEC-C19 L3
MPXBRM-EEBC4O3N
Schuko L1
MPXBRM-EEBC3P1N
Schuko L2
MPXBRM-EEBC3P2N
Schuko L3
MPXBRM-EEBC3P3N
Switzerland T23
MPXBRM-EEBC4S1N
Switzerland T23
MPXBRM-EEBC4S2N
Switzerland T23
MPXBRM-EEBC4S3N
GST18
MPXBRM-EEBC9U1N
GST18
MPXBRM-EEBC9U2N
GST18
MPXBRM-EEBC9U3N
IEC-C13 L1
MPXBRM-EBBC6N1N
IEC-C13 L2
MPXBRM-EBBC6N2N
IEC-C13 L3
MPXBRM-EBBC6N3N
IEC-C19 L1
MPXBRM-EBBC4O1N
IEC-C19 L2
MPXBRM-EBBC4O2N
IEC-C19 L3
MPXBRM-EBBC4O3N
Schuko L1
MPXBRM-EBBC3P1N
Schuko L2
MPXBRM-EBBC3P2N
Schuko L3
MPXBRM-EBBC3P3N
IEC-C13 L1
MPXBRM-ERBC6N1N
IEC-C13 L2
MPXBRM-ERBC6N2N
IEC-C13 L3
MPXBRM-ERBC6N3N
IEC-C19 L1
MPXBRM-ERBC4O1N
IEC-C19 L2
MPXBRM-ERBC4O2N
IEC-C19 L3
MPXBRM-ERBC4O3N
Schuko L1
MPXBRM-ERBC3P1N
Schuko L2
MPXBRM-ERBC3P2N
Schuko L3
MPXBRM-ERBC3P3N
1xTemp.
SN-Z01
3xTemp.
SN-Z02
3xT. + 1xHum
SN-Z03
1xTemp. Mod.
SN-T
Temp/Hum Mod.
SN-TH
2xDoor Mod.
SN-2D
3xInput Mod.
MPX™
Branch-Monitored
SN-3C
RPCBDM-1000
Different combinations available
Rack PDUs | 209
*Note: One-phase input modules can only be populated with L1 modules.
1ph 32A fixed*
MPX™
Elementary
Phase-Monitored
Upgrade possible
Busbar
MPX™
Elementary
MPX™
Simple integration into DCIM systems
The MPH2™ and MPX™ rack PDUs can be administrated locally and remotely. Thanks to the metering of all
electrical parameters right up to output, phase, bank or rack PDU levels, as well as the integration of environment
sensors, these rack PDUs are key when recording power consumption and environment information at rack level.
Since they support all important industry standards and protocols for administration, authentication and
encryption, these products can easily be integrated into any existing network or system architecture.
Flexible local and remote management
The integrated MPH2 standard display provides readings
of all important rack-related information. The optional BDM
local display is available for MPH2 or MPX and can easily be
mounted to where it can best be read.
The Avocent Rack Power Manager which includes access and
control functions, enables central administration of all rack
PDUs in the data center, simplifying administration and monitoring of your PDUs.
Remote communication at rack PDU level is delivered by
the modular hot-swap-enabled RPC2™ card, which is
maintenance – friendly and provides seamless extendability.
RPC2 features:
Supports up to four PDUs within one PDU Rack Array™:
Minimizes number of IP addresses.
Supports up to ten environment sensors: Consolidates
power and environment monitoring at rack level.
Supports Web UI, CLI, SSH and Telnet: Windows, Linux
and network administrators can use their preferred
communication to the rack PDU.
Supports all standard remote authentication and
encryption protocols: Simple integration into existing
security infrastructure.
Supports SNMP v1, v2 and v3: For secure communication
across network management systems.
Supports IPv4 and IPv6: Future-proof IP support for rack
PDUs.
Data protocols: All data is automatically stored
making trouble shooting easy without involving external
management software.
The Rack Power Manager is equipped with state-of-the-art
monitoring capabilities that enable intelligent server grouping
across disparate racks. It also enables custom reporting,
scheduled regular reports and the ability to set real-time
threshold alerts to give you the highest quality information on
your data center’s power infrastructure so as to truly leverage
the investment in PDUs.
Remote monitoring interface featuring:
Snapshot of all electrical parameters on output, group,
phase and entire levels.
Snapshot of environment-sensor metering values and
status.
Threshold value configuration, alert and notification.
Control of individual outputs and groups.
Status information and configuration of all outputs.
Network management settings.
Command-line interface
210 | Rack PDUs
User interface
Measure and Track Power Costs – The Rack Power Manager
calculates and compares cost across multiple levels (rack,
row, data centers or companies) to track cost over a period
of time and also measure the impact of any consolidation
or expansion projects.
Review Historical Capacity and Consumption Reports –
Plan for future expansion or new facilities more accurately
based on real historical data.
Protect Against Downtime – Help get a total reading on
power usage for the data center and set a maximum
threshold of power usage. Set alerts to know when the
threshold is reached or exceeded and allow time to make
changes.
Precision planning – Help IT identify what electrical
infrastructure to build into a new location or disaster
recovery site. The design can be based on real historical
data rather than maximum values or estimates.
Avocent® Rack Power Manager
MPX™
Optimal Utilization of Your Rack PDU Investment
The MPX™ and MPH2™ rack PDUs can be integrated in industry-leading KVM systems, serial consoles and Emerson
Network Power infrastructure management systems. Furthermore, the rack PDU monitoring and environment
information can be integrated into comprehensive data-center management software provided by Emerson Network Power or a third party. The information provided by this intelligent rack PDU offers Emerson Network Power's
customers a comprehensive, user-friendly power distribution and administrative solution.
Integration into the Avocent® Advanced Console Server,
MergePoint™ Unity KVM Switches and Universal
Management Gateway-Appliances offers the following
benefits:
Rack PDUs are integrated into the out-of-bandmanagement solution.
Rack PDUs are included in a consolidated access and
control solution.
The number of IP addresses required for rack PDU
administration are minimized.
By consolidating all data-center management functionality
into a single interface, Avocent DSView™ 4 management
software delivers the complete data-center control necessary
for the 24/7 data center.
The software enables secure, out-of-band, centralized
management of all connected IT and network devices in
complex and geographically dispersed data centers.
When used in conjunction with KVM appliances, serial console
appliances, service processor gateways and PDUs, the hardware and software combine to allow IT administrators to remotely access, monitor and control target devices on multiple
platforms at numerous locations–anywhere, anytime.
Used in combination with rack PDUs, DSView4 management
software ensures:
that PDUs are part of a consolidated access and control
solution.
simple assignment of IT equipment to PDU outputs
they are connected to.
that PDUs are part of a consolidated authentication,
authorization and audit solution.
The Trellis™ platform is a trailblazing DCIM innovation from
Emerson Network Power. It minimizes IT risks while increasing
operating efficiency, overcoming challenges and preparing
you for the future.
For both expansion and consolidation, as well as planning IT
measures, constant monitoring, tracking and an overview of
real-time infrastructure metered values and data are necessary for precision planning and making informed decisions.
The Trellis platform provides all relevant information when
you need it enabling data center administration without
having to use several tools.
With real-time visualization, power-supply monitoring and
mobile access offered by the Trellis™ platform you can:
Reduce inefficiencies without interrupting running
processes.
Postpone investments and increase your operating margin.
Improve the Service Level Agreement with comprehensive
transparency across the entire infrastructure.
Reduce operating costs without compromising availability
and adaptability.
Manage remote resources more effectively.
Increase overall efficiency by gaining a better insight into
the data center.
Integration into Liebert® Nform™
and Liebert SiteScan® delivers:
Inclusion of rack PDUs in a consolidated
monitoring solution for data centers
at infrastructure level.
Real-time monitoring and control
of almost every component of the
critical support equipment.
Date analysis and trend reports.
Event management.
Rack PDUs | 211
MPX™
MPX™ – Input Module/Power Supply
Elementary and Monitored type
– The MPX PEM is fixed on the MPX PRC and
provides the connection to the power supply.
– Fixed-connection cable; 3 m long.
– With IEC60309 plug, 1Ph/N/PE 6h blue,
3Ph/N/PE 6h red.
Monitored type
– The MPX PEM provides connection to the
databus for data communication.
– Integrated RPC2 communication card enables
remote monitoring and maintenance of the
MPX modules.
– Provides the following phase-input data:
voltage, current, effective power, consumption
and frequency.
– Power alarm functions for individual phases and
their operating status are also supported.
– Further important features: Three displays
inform the user on the current status of
each individual input. An acoustic alarm is
activated at certain overload conditions.
– The communication card centralizes the
MPXs local and remote administration.
– Serves as the connection point for versatile
support options and devices, such as the display
module (RPC BDM), various sensors and
connection to other MPX™ or MPH2™ systems,
for example.
– Has RJ-45 ports for all connections (except USB
port) and does not require any special cabling.
DOS20153
Technical Data Interfaces:
– RJ-45 LAN port (10/100 MBit) – for local
network (LAN) connection via an Ethernet
cable.
– Expansion / administration port for local
configuration using a computer / laptop,
for creating a link-up of several PDUs
(MPX or MPH).
– Serial interface RS232.
Dimensions in mm:
U
n = Number of sockets
H = Height
F1 = Standard side panel
L = Length
F2 = Design side panel
S = Switch
19" = ideal for 19" components
U
= Standard rack unit
1 U = 44.45 mm
Dimensions
– Width: 75 mm.
– Height: 65 mm.
– Feed cable: 3 m.
Color
– Enclosure: aluminum/RAL7021 dark-gray
Certification
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
Standard inclusion
– 1 x MPX PEM power input module.
– Including connection cable.
– Including RPC2 communication card
(only Monitored type).
W
H
Feed
Load rating
Type
Order No.
UP
220
75
65
Fixed
230 VAC, max. 32 A
Elementary
MPXPEM-EHAEXQ30
1 unit
220
75
65
Fixed
230/400 VAC, max. 16 A Elementary
MPXPEM-EHAEXT30
1 unit
220
75
65
Fixed
230/400 VAC, max. 32 A Elementary
MPXPEM-EHAEXR30
1 unit
266
75
65
Fixed
230/400 VAC, max. 63 A Elementary
MPXPEM-EHBEXZ30
1 unit
220
75
65
Fixed
230 VAC, max. 32 A
Monitored
MPXPEM-EHABXQ30
1 unit
220
75
65
Fixed
230/400 VAC, max. 16 A Monitored
MPXPEM-EHABXT30
1 unit
220
75
65
Fixed
230/400 VAC, max. 32 A Monitored
MPXPEM-EHABXR30
1 unit
266
75
65
Fixed
230/400 VAC, max. 63 A Monitored
MPXPEM-EHBBXZ30
1 unit
1 mm = 0.03937 inch
1 kg = 2.2046 pounds
UP = Packaging unit
Safe = child-proof
Replace .x with the number of the color combination you require: .1 = RAL 7035, .6 = RAL 7035/RAL 2003
212 | Rack PDUs
Material / Finish
– Enclosure: aluminum.
– Cover: sheet steel.
– Power contacts: silver-plated.
– Databus contacts: gold-plated
(only Monitored type)
L
Conversion:
W = Width
– Display port for connecting the RPC BDM
(display module).
– External sensor port for connecting optional
sensors.
– Remote management: Onboard Web
interface, CLI, SNMPv1,2,3, SSH, Telnet Syslog,
compatible with Avocent ACS, UMG & MPU,
SiteScan, DSView, Rack Power Manager,
Nform & Trellis as well as Nagios or other
management software programs.
– Authentication: local, remote: Active
Directory, LDAP, TACACS, Radius, Kerberos.
– Encryption: MD5, AES, DES.
MPX™
MPX™ BRM – Output Module
– The MPX BRM enables the distribution
to the individual consumers.
– Each module taps a color-coded phase.
– All modules are protected against overload
with a 20 A circuit breaker.
– Modules can be exchanged during operation
thereby facilitating user-specific installation
without having to shut down the MPX.
– Up to 3 BRM output modules can be installed on
a 1,035 mm PRC busbar; up to 6 BRM output
modules can be installed on a 1,880 mm PRC
busbar.
Material / Finish
– Enclosure: aluminum.
– Cover: sheet steel.
– Power contacts: sliver-plated.
– Databus contacts: gold-plated
(only type B and R).
DOS20153
Type E – Elementary
– Module for power distribution via respective
outputs.
Type B – Branch-Monitored
– Module for power distribution via respective
outputs with metering function on module
level.
– The MPX BRMs have LED ID indicator which
identifies every module with a number.
– Modules are administered in the software.
– Provides the following metered readings:
voltage, current, power, apparent power, kWh
and power factor.
– Power alarm functions and operating status are
supported.
Type R – Receptacle Managed:
– Module for power distribution via respective
outputs with metering function on module level
and output level.
– The MPX BRMs have LED ID indicator which
identifies every module with a number.
– Modules are administered in the software.
– Provides the following metered readings:
voltage, current, power, apparent power, kWh,
frequency, power factor and crest factor.
– Power alarm functions and operating status are
supported.
– Individual outputs can be switched on and off
remotely.
Dimensions
– Width: 75 mm.
– Height: 65 mm.
Color
– Enclosure: aluminum/RAL7021 dark-gray
Certification
– CE label in accordance with Low Voltage
Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
Standard inclusion
– 1 x MPX PEM power output module.
– 1 x instruction manual.
L
n
Outputs
Load rating per output
Phase tap
Type Order No.
UP
266
7
IEC320 C 13
10 A
L1
E
MPXBRM-EEBC7N1N
1 unit
266
7
IEC320 C 13
10 A
L2
E
MPXBRM-EEBC7N2N
1 unit
266
7
IEC320 C 13
10 A
L3
E
MPXBRM-EEBC7N3N
1 unit
266
4
IEC320 C 19
16 A
L1
E
MPXBRM-EEBC4O1N
1 unit
266
4
IEC320 C 19
16 A
L2
E
MPXBRM-EEBC4O2N
1 unit
266
4
IEC320 C 19
16 A
L3
E
MPXBRM-EEBC4O3N
1 unit
266
3
Schuko CEE 7/4
16 A
L1
E
MPXBRM-EEBC3P1N
1 unit
266
3
Schuko CEE 7/4
16 A
L2
E
MPXBRM-EEBC3P2N
1 unit
266
3
Schuko CEE 7/4
16 A
L3
E
MPXBRM-EEBC3P3N
1 unit
266
4
Switzerland T23
16 A
L1
E
MPXBRM-EEBC4S1N
1 unit
266
4
Switzerland T23
16 A
L2
E
MPXBRM-EEBC4S2N
1 unit
266
4
Switzerland T23
16 A
L3
E
MPXBRM-EEBC4S3N
1 unit
266
9
GST18 3-pole
16 A
L1
E
MPXBRM-EEBC9U1N
1 unit
266
9
GST18 3-pole
16 A
L2
E
MPXBRM-EEBC9U2N
1 unit
266
9
GST18 3-pole
16 A
L3
E
MPXBRM-EEBC9U3N
1 unit
266
6
IEC320 C 13
10 A
L1
B
MPXBRM-EBBC6N1N
1 unit
266
6
IEC320 C 13
10 A
L2
B
MPXBRM-EBBC6N2N
1 unit
266
6
IEC320 C 13
10 A
L3
B
MPXBRM-EBBC6N3N
1 unit
266
4
IEC320 C 19
16 A
L1
B
MPXBRM-EBBC4O1N
1 unit
266
4
IEC320 C 19
16 A
L2
B
MPXBRM-EBBC4O2N
1 unit
266
4
IEC320 C 19
16 A
L3
B
MPXBRM-EBBC4O3N
1 unit
266
3
Schuko CEE 7/4
16 A
L1
B
MPXBRM-EBBC3P1N
1 unit
266
3
Schuko CEE 7/4
16 A
L2
B
MPXBRM-EBBC3P2N
1 unit
266
3
Schuko CEE 7/4
16 A
L3
B
MPXBRM-EBBC3P3N
1 unit
266
6
IEC320 C 13
10 A
L1
R
MPXBRM-ERBC6N1N
1 unit
266
6
IEC320 C 13
10 A
L2
R
MPXBRM-ERBC6N2N
1 unit
266
6
IEC320 C 13
10 A
L3
R
MPXBRM-ERBC6N3N
1 unit
266
4
IEC320 C 19
16 A
L1
R
MPXBRM-ERBC4O1N
1 unit
266
4
IEC320 C 19
16 A
L2
R
MPXBRM-ERBC4O2N
1 unit
266
4
IEC320 C 19
16 A
L3
R
MPXBRM-ERBC4O3N
1 unit
266
3
Schuko CEE 7/4
16 A
L1
R
MPXBRM-ERBC3P1N
1 unit
266
3
Schuko CEE 7/4
16 A
L2
R
MPXBRM-ERBC3P2N
1 unit
266
3
Schuko CEE 7/4
16 A
L3
R
MPXBRM-ERBC3P3N
1 unit
Rack PDUs | 213
MPX™
MPX™ PRC – Power Distribution Unit / Communication Bus
– The MPX PRC is the basic element of the
MPX power distribution unit.
– Power and data transfer buses are integrated
across the entire length of the MP PRC.
– The MPX BRMs (output modules) and the MPX
PEM (power input module) are fixed on the MPX
PRC and, depending on the type, facilitate the
modules' power feed, output, monitoring and
management.
Approvals
– CE label in accordance with Low Voltage
Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
Load rating
– Max. current: 3 x 63 A.
– Nominal voltage (L-N / L-L): 230 / 400 VAC.
Material / Finish
– Busbar housing: aluminum.
– Busbars: copper.
– Databus: gold-plated.
Standard inclusion
– 1 x MPX PRC - power distribution unit /
communication bus.
– 1 x mounting kit.
Dimensions
– Width: 68 mm.
– Height: 24 mm.
DOS20153
Color
– Enclosure: aluminum.
L
W
H
U
Model
Order No.
UP
1035
68
24
23
1 PEM (220 mm) + 3 BRM
MPXPRC-V1035XXX
1 unit
1880
68
24
42
1 PEM (220/266 mm) + 6 BRM
MPXPRC-V1880XXX
1 unit
MPX™/MPH™/MPH2™/IMS™ – Sensors
DOS20153
– These sensors are designed for tool-less
installation in a Knürr Miracle / DCM rack, and is
also compatible with all other rack types.
– "Fixed" type sensors are attached to a cable.
– "Modular" type sensors can be connected to the
delivered cable.
– Plugged into the RPC-1000 or RPC2
communication card.
– Several sensors can be connected in rows.
– Automatically displayed in the MPX/MPH/
MPH2/IMS software.
– Temperature measurement range: 5 – 60° C.
– Accuracy: ± 0.5° C.
– Humidity measurement range: 10 – 95 %.
– Accuracy: ± 3.5 %.
Standard inclusion
– 1 x sensor with connection cable.
– 1 x instruction manual.
Cable length Type
Model
Order No.
UP
3660
Fixed
Temperature sensor, single
SN-Z01
1 unit
5180
Fixed
Temperature sensor, triple
SN-Z02
1 unit
5180
Fixed
Temperature sensor, triple + humidity sensor, single
SN-Z03
1 unit
2000
Modular
Temperature sensor, single
SN-T
1 unit
2000
Modular
Temperature sensor, single + humidity sensor, single
SN-TH
1 unit
2000
Modular
2 x door contact - input module*
SN-2D
1 unit
2000
Modular
3 x digital input
SN-3C
1 unit
* Suitable door contact switch: Order no.: 06.108.115.9
214 | Rack PDUs
Note
Sensors are not required for operating the MPX
or MPH, MPH2, IMS. However, a communication
card is needed.
MPX™
RPC BDM - 1000 Display Module
DOS20153
– Provides the local display of the monitored
data for all connected MPX/MPH/MPH2/IMS
systems.
– Operated with a navigation switch.
– Connected via a cable with the RPC, enabling
the user to place the displays where they can be
easily read in the given local space conditions.
– An individual display can be used for up to
four MPX/MPH/MPH2/IMS PDUs, which are all
connected in a PDU array.
L
W
H
U
Note
The display module is not required when
operating the MPX or MPH, MPH2, IMS.
However, a communication card is needed.
Standard inclusion
– 1 x RPCBDM-1000 display module.
– 1 x connection cable 2 m.
– 1 x mounting kit.
Model
Order No.
UP
RPCBDM-1000
1 unit
BRM Power-Distribution Cable-Holder Clip Set
xxx
– Cable clips provide strain relief
for the feed lines of the network equipment.
– Cable clips are suitable for most IEC-C13 socket
plugs with a raised edge. (Must be checked for
suitability).
– Cable clips are sold in sets of 18 units.
Standard inclusion
– 1 x cable holder set (18 units).
L
W
H
U
Delivery
– In sets.
Note
– Optimal function only with cable connector
04.000.051.9.
– Can only be used with MPXBRM-EBBC6NxN
and MPXBRM-ERBC6NxN (x = 1 ,2, 3).
Model
Order No.
UP
03.910.216.9
1 unit
xxx
SafetySleeve™ Cable Protection IEC C19
– SafetySleeves protect the feed lines of the
network equipment.
– They can be used on all C19 cables and fit onto
all PDUs.
DOS20493
L
W
H
U
Material / Finish
– PVC, black.
Model
Order No.
UP
C20 plug in C19 socket
03.910.212.9 001
20 unit
SafetySleeve™ Cable Protection IEC C13
– SafetySleeves protect the feed lines of the
network equipment.
– They can be used on all C13 cables and fit onto
all PDUs.
Material / Finish
– PVC, black.
DOS20494
L
W
H
U
Model
Order No.
UP
C14 plug in C13 socket
03.910.213.9 001
50 unit
Rack PDUs | 215
MPH2™
MPH2™ – Managed Rack PDU
Monitoring and Control
The newly developed MPH2™ Managed Rack PDU is a power supply system with monitoring and control
functions. The MPH2™ offers outstanding features such as easy rack-integration and management architecture
as well as optimum availability and energy efficiency.
Four MPH2™ versions are available:
With input metering, output metering and
output switching.
With input metering and output metering.
With input metering and output switching.
With input metering.
Benefits of MPH2™
Monitors several parameters with defined thresholds
and alarm tools.
Monitors and controls individual outputs
and/or load and appliance groups.
A variety of measurements allow you to predict failing
conditions before they occur and proactively manage
connected equipment for maximum uptime.
Energy and power metering maximize the data center
power and cooling infrastructure.
Lowest power consumption of all switched-rack PDUs
lowers power costs and thermal load.
Up to four rack MPH2™ PDUs can be connected in a
Rack PDU Array™ thereby consolidating user-specific IP
connections and equipment monitoring.
Developed for critical environments
Industry-leading operating temperature of up to
60° C suitable for high temperatures inside racks.
Bistable relays ensure basic power supply even when
shortfalls occur elsewhere.
Accurate voltage and current metering up to outlet
level with ±1 % tolerances deliver reliable results.
Extensive alarm functions including notification when
an overload occurs in individual groups.
Monitoring of environment conditions
(temperature, humidity and input contacts) with
alerts and alarms.
Notification upon failure or if loads are removed in
individual racks.
MPH2™ savings for a typical data center
Typical rack PDU
with 24 outputs
MPH2™
Power consumption of PDU
(in Watt)
20
5
Annual energy consumption
of PDU (kWh)
176
44
Total proportion of the data center's energy consumption (kWh)*
333
83
Energy saving
Compared with a Switched Rack-PDU model
for a typical data center with a 1.9 PUE.
* according to Energy Logic calculations
kWh
333
75 % cost saving
83
Typical rack PDU
216 | Rack PDUs
75 %
MPH2TM
MPH2™
INPUT POWER
16 to 32 A (EU).
Single-phase and three-phase.
OUTPUT DISTRIBUTOR
IEC C13 and IEC C19.
Combination systems.
MODULARITY
Communication card.
External display.
External sensors.
MONITORING
Three various levels: Input level, group level,
output level
Temperature and humidity.
Door contacts and potential-free input contacts.
REMOTE CONTROLLED SOCKETS
Socket level.
MPH2™
MPH2™
Benefits
Highest availability levels
Modular communications card; can be replaced during
operation. This simplifies maintenance and increases
the level of availability.
Bistable relays in switchable designs; the server's power
supply is ensured even during outages.
Software-controlled overload protection – affected
outputs are switched off before the advance fuse is
activated.
Additional metering of the neutral conductor and of
the crest factor; possible faults that cause switch-off are
detected in advance.
Leading technology in many areas
Operating temperatures of up to 60 °C allow secure
operation in the warm aisle.
Metering accuracy of ± 1 % ensures reliable
measurement results.
Power losses of approx. 5 W, even in switchable models,
reducing electricity costs and minimizing the thermal
load.
218 | Rack PDUs
Industry-leading management properties
An integrated local display and an optional external
display facilitates flexible local management.
Onboard web interface and CLI/SSH interface; suitable
for both Windows and Linux administration.
A variety of authentication options and encrypted
protocols ensure integration into Enterprise Security
architectures.
SNMPv3 and IPv6 support so that current requirements,
particularly from the public sector, can be satisfied.
Simple integration into ENP solutions
Can be delivered pre-installed in Knürr racks to save
time and costs during installation in the data center.
Serial integration into Avocent UMG, ACS and MPU
guarantees redundant management access to the
MPH2.
Integration into ENP software solutions; the MPH2 is an
integral part of a comprehensive DCIM solution with
monitoring and control functions.
MPH2™
Special tool-less Knürr DCM rack
fixture:
Lowers installation costs and extra space in
rack for cables and other components.
Communications module (RPC2™):
Offers extendable interfaces for network
communication, sensors and local display.
BDM™ local display module
Extended diagnostic functionality;
user-friendly display. Features include
detailed information about alerts and
specific labeling for outputs.
Connection cable with locking mechanism
Prevents IT cables from being accidentally
disconnected.
SN sensors:
Consolidates environmental monitoring of
temperature, humidity and potential-free input
contacts with the power supply at rack level.
Integrated display:
Provides easy access to important
information on the rack.
Ultra-flat circuit breakers:
Compact construction; minimizes
space requirements in the rack.
Flexible network cable input:
Simplifies installation in the rack PDU.
Cable and fixed wiring options:
Flexible power distribution; input-cable
can be connected locally.
Rack PDUs | 219
MPH2™
Simple Integration into DCIM Systems
The MPH2™ and MPX™ rack PDUs can be administrated locally and remotely. Thanks to the metering of all
electrical parameters right up to output, phase, bank or rack PDU levels and the integration of environment
sensors, these rack PDUs are key to recording power consumption and environment information at rack level.
Since they support all important industry standards and protocols for administration, authentication and
encryption, these products can easily be integrated into any existing network or system architecture.
Flexible local and remote management
The integrated MPH2 standard display provides readings
of all the important rack-related information. The optional
BDM local display is available for MPH2 or MPX and can easily
be mounted where necessary.
The Avocent Rack Power Manager, which includes access
and control functions, enables central administration of all the
rack PDUs in the data center simplifying the administration
and monitoring of your PDUs.
Remote communication at rack PDU level is delivered by
the modular hot-swap-enabled RPC2™ card, which is
user-friendly and provides seamless extendability. RPC2
features:
Support for up to four PDUs within one PDU Rack
Array™: Minimizes number of IP addresses.
Supports up to ten environment sensors: Consolidates
power and environment monitoring on rack level.
Supports Web UI, CLI, SSH and Telnet: Windows, Linux
and network administrators can use their preferred
communication to the rack PDU.
Supports all standard remote authentication and
encryption protocols: Simple integration into existing
security infrastructure.
Supports SNMP v1, v2 and v3: For secure communication
across network management systems.
Supports IPv4 and IPv6: Future-proof IP support for rack
PDUs.
Data protocols: All data is automatically stored making
trouble shooting easy without involving external
management software.
The Rack Power Manager is equipped with state-of-the-art
monitoring capabilities that enable intelligent server grouping
across disparate racks. It also enables custom reporting,
scheduled regular reports and the ability to set real-time
threshold alerts to give you the highest quality information on
your data center’s power infrastructure and so you can truly
leverage the investment in PDUs.
Remote monitoring interface featuring:
Snapshot of all electrical parameters on output, group,
phase and entire levels.
Snapshot of environment-sensor metering values and
status.
Threshold value configuration, alert and notification.
Control of individual outputs and groups.
Status information and configuration of all outputs.
Network management settings.
Command-line interface
220 | Rack PDUs
User interface
Measure and Track Power Costs – The Rack Power Manager
calculates and compares cost across multiple levels (rack,
row, data centers or companies) to track cost over a period
of time and also to measure the impact of any consolidation or expansion projects.
Review Historical Capacity and Consumption Reports –
Plan for future expansion or new facilities more accurately
based on real historical data rather than manufacturer's
data or estimates which result in overbuilding and lead to
inefficiencies.
Protect Against Downtime – Help get a total reading on
power usage for the data center and set a maximum
threshold of power usage. Set alerts to know when the
threshold is reached or exceeded and allow time to make
changes before there are actual problems.
Precision planning – Help IT know what electrical infrastructure to build into a new location or disaster recovery site. The
design can be based on actual historical data rather than
maximum values or estimates which result in overbuilding
and lead to hard-to-correct inefficiencies.
Avocent® Rack Power Manager
MPH2™
Optimal Utilization of Your Rack PDU Investment
The MPX™ and MPH2™ rack PDUs can be integrated in industry-leading KVM systems, serial consoles and Emerson
Network Power infrastructure management systems. Furthermore, the rack PDU monitoring and environment
information can be integrated into comprehensive data-center management software provided by Emerson or a
third party. The information provided by this intelligent, easy-to-use rack PDU offers Emerson Network Power's
customers a comprehensive, user-friendly power distribution and administration solution.
Integration into the Avocent® Advanced Console Server,
MergePoint™ Unity KVM Switches and Universal Management Gateway-Appliances offer the following benefits:
Rack PDUs are integrated into the out-of-band-management solution.
Rack PDUs are included in a consolidated access and
control solution.
The number of IP addresses required for rack PDU
administration are minimized.
By consolidating all data-center management functionality
into a single interface, Avocent DSView™ 4 management
software delivers the complete data-center control necessary
for the data center.
The software enables secure, out-of-band, centralized
management of all connected IT and network devices in
complex and geographically dispersed data centers.
When used in conjunction with KVM appliances, serial console
appliances, service processor gateways and PDUs, hardware
and software combine to allow IT administrators to remotely
access, monitor and control target devices on multiple platforms at numerous locations–anywhere, anytime.
Used in combination with rack PDUs, DSView4 management
software ensures:
That PDUs are part of a consolidated access and control
solution.
Simple assignment of IT equipment to the PDU outputs
they are connected to.
That PDUs are part of a consolidated authentication,
authorization and audit solution.
The Trellis™ platform is a trailblazing DCIM innovation from
Emerson Network Power. It minimizes IT risks while increasing
operating efficiency solving existing problems and preparing
you for the future.
For both expansion and consolidation, as well as planning IT
measures, constant monitoring, tracking and an overview
of real-time infrastructure, metered values and data are necessary for precision planning and making informed decisions.
The Trellis platform provides all the relevant information
providing data center administration without having to resort
to several tools.
With the time visualization, power-supply monitoring and
mobile access offered by the Trellis platform, you can:
Reduce inefficiencies without interrupting running
processes.
Postpone investments and increase the operating margin.
Improve the Service Level Agreement with comprehensive
transparency across the entire infrastructure.
Reduce operating costs without compromising availability
and adaptability.
Manage remote resources more effectively.
Increase overall efficiency by gaining better insight into the
data center.
Integration into Liebert® Nform™
and Liebert SiteScan® delivers:
Inclusion of rack PDUs in a consolidated
monitoring solution for data centers
at infrastructure level.
Real-time monitoring and control
of almost every component of the
critical support equipment.
Data analysis and trend reports.
Event management.
Rack PDUs | 221
MPH2™
MPH2™
– The MPH2 is a power distribution unit for
IT racks which provides metering of electrical
values. Depending on the model, individual
outputs can also be remote-controlled.
– The integrated RPC2k communications card
allows you to connect up to 4 MPH2 / MPX™
units as well as monitor and maintain all
connected units remotely. Up to 10 sensors
(temperature, air humidity, door contacts as
well as potential-free input contacts) can be
connected.
– The MPH2™ unit has an integrated display. In
addition, the optional external RPCBDM-1000
display module can easily be connected and
mounted on the rack.
– Special cables with locking mechanisms can be
connected to the outputs.
– Depending on the model, the connecting cable
for the MPH2 is attached to the housing (cable
length 3 m), also permitting a connecting cable
can be connected on site (model with connection unit).
– Remote management: Onboard Web Interface,
CLI, SNMPv1,2,3, SSH, Telnet, integratable into
Avocent ACS, UMG & MPU, DSView, Rack Power
Manager, Nform & Trellis as well as Nagios or
other management software programs.
– Authentication: local, remote:
active directory, LDAP, TACACS, Radius, Kerberos. Encryption: MD5, AES, DES.
– Measurement parameters: Current (A), voltage
(V), real power (W), apparent power (VA),
consumption (kWh), power factor, frequency
and crest factor (only tapes M and R).
Accuracy: ±1 % (V, A).
MPH2™ Types
for Europe
MPH2™ B – input metering
MPH2™ C – input metering and output switching
MPH2™ M – input metering and output metering
MPH2™ R – input metering, output metering and output switching
Type
Input Values
Voltage
Material / finish / color
– Closed housing, aluminum profile, finely
textured powder-coated top (RAL 7021),
Vampamid 6 0024 V0 (UL94) recyclable
plastic parts, finely textured and colored
(RAL 9005).
Mechanical dimensions
– Width x depth x length (mm):
56 x 50 x (see table).
Certification
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
MPH2™ models
– MPH2™ B – Metering per phase and per
group (only models with >16 A input power).
– MPH2™ C – Metering per phase and per
group (only models with >16 A input power).
Each output can also be individually switched
remotely.
– MPH2™ M – Metering per phase and per
group (only models with >16 A input power)
and per output.
– MPH2™ R – Metering per phase and per
group (only models with >16 A input power)
and per output. Each output can also be
individually switched remotely.
Input Connector
Current
Standard inclusion
– MPH2™ rack PDU.
– Standard mounting bracket.
– Safety instructions.
– Quickstart guide.
Outputs
Length
C13
C19
(mm)
2
916.5
B
230V
16A
C20 inlet
17
B
230V
16A
C20 inlet
21
B
230V
16A
C20 inlet
30
B
230V
16A
IEC 60309 16A 1P+N+G
17
B
230V
16A
IEC 60309 16A 1P+N+G
21
B
230V
16A
IEC 60309 16A 1P+N+G
30
Order Number
MPHB3241
916.5
MPHB3141
6
1736.5
MPHB1241
2
916.5
MPHB3242
6
916.5
MPHB3142
1736.5
MPHB1242
B
230V
32A
IEC 60309 32A 1P+N+G
30
6
1736.5
MPHB1243
B
230V
32A
Connection unit
30
6
1736.5
MPHB1260
6
B
230/400V
3 x 16A
IEC 60309 16A 3P+N+G
30
B
230/400V
3 x 32A
IEC 60309 32A 3P+N+G
42
1736.5
MPHB1244
1826.5
MPHB1545
B
230/400V
3 x 32A
IEC 60309 32A 3P+N+G
18
12
1826.5
MPHB1345
B
230/400V
3 x 32A
IEC 60309 32A 3P+N+G
30
6
1826.5
MPHB1245
B
230/400V
3 x 32A
Connection unit
42
1826.5
MPHB1562
B
230/400V
3 x 32A
Connection unit
18
12
1826.5
MPHB1362
6
1826.5
MPHB1262
916.5
MPHC3341
B
230/400V
3 x 32A
Connection unit
30
C
230V
16A
C20 inlet
8
C
230V
16A
C20 inlet
16
C
230V
16A
C20 inlet
18
C
230V
16A
C20 inlet
24
C
230V
16A
IEC 60309 16A 1P+N+G
18
1004
MPHC3141
6
1736.5
MPHC1141
1736.5
MPHC1241
6
1736.5
MPHC1142
C
230V
16A
IEC 60309 16A 1P+N+G
24
1736.5
MPHC1242
C
230V
16A
IEC 60309 16A 1P+N+G
16
1004
MPHC3142
C
230V
32A
IEC 60309 32A 1P+N+G
18
1736.5
MPHC1143
222 | Rack PDUs
6
MPH2™
Type
Input Values
Voltage
Input Connector
Current
Outputs
C13
C
230V
32 A
IEC 60309 32 A 1P+N+G
24
C
230V
32 A
Connection unit
18
C
230V
32 A
Connection unit
24
C
230/400V
3 x 16 A
IEC 60309 16 A 3P+N+G
18
C
230/400V
3 x 16 A
IEC 60309 16 A 3P+N+G
24
C
230/400V
3 x 16 A
Connection unit
18
C
230/400V
3 x 16 A
Connection unit
24
C
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
18
C
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
24
Length
C19
1736.5
6
6
6
6
Order Number
(mm)
MPHC1243
1736.5
MPHC1160
1736.5
MPHC1260
1736.5
MPHC1144
1736.5
MPHC1244
1736.5
MPHC1161
1736.5
MPHC1261
1736.5
MPHC1145
1736.5
MPHC1245
MPHC1345
C
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
6
12
1736.5
C
230/400V
3 x 32 A
Connection unit
18
6
1736.5
MPHC1162
C
230/400V
3 x 32 A
Connection unit
24
1736.5
MPHC1262
C
230/400V
3 x 32 A
Connection unit
6
1736.5
MPHC1362
M
230V
16 A
C20 inlet
8
916.5
MPHM3341
MPHM3342
12
M
230V
16 A
IEC 60309 16 A 1P+N+G
8
916.5
M
230V
16 A
C20 inlet
16
1004
MPHM3141
M
230V
16 A
C20 inlet
18
6
1736.5
MPHM1141
1736.5
MPHM1241
6
1736.5
MPHM1142
MPHM1242
M
230V
16 A
C20 inlet
24
M
230V
16 A
IEC 60309 16 A 1P+N+G
18
M
230V
16 A
IEC 60309 16 A 1P+N+G
24
1736.5
M
230V
16 A
IEC 60309 16 A 1P+N+G
16
1004
MPHM3142
M
230V
32 A
IEC 60309 32 A 1P+N+G
18
1736.5
MPHM1143
1736.5
MPHM1243
M
230V
32 A
IEC 60309 32 A 1P+N+G
24
M
230V
32 A
Connection unit
18
M
230V
32 A
Connection unit
24
M
230/400V
3 x 16 A
IEC 60309 16 A 3P+N+G
18
M
230/400V
3 x 16 A
IEC 60309 16 A 3P+N+G
24
M
230/400V
3 x 16 A
Connection unit
18
M
230/400V
3 x 16 A
Connection unit
24
M
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
18
M
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
24
6
6
6
6
6
1736.5
MPHM1160
1736.5
MPHM1260
1736.5
MPHM1144
1736.5
MPHM1244
1736.5
MPHM1161
1736.5
MPHM1261
1736.5
MPHM1145
1736.5
MPHM1245
MPHM1345
M
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
6
12
1736.5
M
230/400V
3 x 32 A
Connection unit
18
6
1736.5
MPHM1162
M
230/400V
3 x 32 A
Connection unit
24
1736.5
MPHM1262
1736.5
MPHM1362
M
230/400V
3 x 32 A
Connection unit
6
R
230V
16 A
C20 inlet
8
12
916.5
MPHR3341
R
230V
16 A
IEC 60309 16 A 1P+N+G
8
916.5
MPHR3342
R
230V
16 A
C20 inlet
16
R
230V
16 A
C20 inlet
18
R
230V
16 A
C20 inlet
24
R
230V
16 A
IEC 60309 16 A 1P+N+G
18
R
230V
16 A
IEC 60309 16 A 1P+N+G
R
230V
16 A
IEC 60309 16 A 1P+N+G
R
230V
32 A
IEC 60309 32 A 1P+N+G
18
R
230V
32 A
IEC 60309 32 A 1P+N+G
24
R
230V
32 A
Connection unit
18
R
230V
32 A
Connection unit
24
R
230/400V
3 x 16 A
IEC 60309 16 A 3P+N+G
18
R
230/400V
3 x 16 A
IEC 60309 16 A 3P+N+G
24
R
230/400V
3 x 16 A
Connection unit
18
R
230/400V
3 x 16 A
Connection unit
24
R
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
18
R
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
24
R
230/400V
3 x 32 A
IEC 60309 32 A 3P+N+G
6
12
1736.5
MPHR1345
R
230/400V
3 x 32 A
Connection unit
18
6
1736.5
MPHR1162
1736.5
MPHR1262
12
1736.5
MPHR1362
1004
MPHR3141
6
1736.5
MPHR1141
1736.5
MPHR1241
6
1736.5
MPHR1142
24
1736.5
MPHR1242
16
1004
MPHR3142
1736.5
MPHR1143
1736.5
MPHR1243
R
230/400V
3 x 32 A
Connection unit
24
R
230/400V
3 x 32 A
Connection unit
6
6
6
6
6
6
1736.5
MPHR1160
1736.5
MPHR1260
1736.5
MPHR1144
1736.5
MPHR1244
1736.5
MPHR1161
1736.5
MPHR1261
1736.5
MPHR1145
1736.5
MPHR1245
Rack PDUs | 223
MPH2™
MPX™/MPH™/MPH2™/IMS™ – Sensors
DOS20153
– These sensors are designed for tool-less
installation in a Knürr Miracle / DCM rack, but
is also compatible with all other rack types.
– "Fixed" type sensors are attached to a cable.
– "Modular" type sensors can be connected to the
delivered cable.
– Plugged into the RPC-1000 or RPC2
communication card.
– Several sensors can be connected in rows.
– Automatically displayed in the MPX/MPH/
MPH2/IMS software.
– Temperature measurement range: 5 – 55° C.
– Accuracy: ± 0.5° C.
– Humidity measurement range: 10 – 95 %.
– Accuracy: ± 3.5 %.
Note
The sensors are not required for operating
the MPX or MPH, MPH2, IMS. However, a
communication card is needed.
Standard inclusion
– 1 x sensor with connection cable.
– 1 x instruction manual.
Cable length Type
Model
Order No.
UP
3660
Fixed
Temperature sensor, single
SN-Z01
1 unit
5180
Fixed
Temperature sensor, triple
SN-Z02
1 unit
5180
Fixed
Temperature sensor, triple + humidity sensor, single
SN-Z03
1 unit
2000
Modular
Temperature sensor, single
SN-T
1 unit
2000
Modular
Temperature sensor, single + humidity sensor, single
SN-TH
1 unit
2000
Modular
2 x door contact - input module*
SN-2D
1 unit
2000
Modular
3 x digital input
SN-3C
1 unit
* Suitable door contact switch: Order no.: 06.108.115.9
Liebert RPC BDM - 1000 Display Module
DOS20153
– Provides the local display of the monitored
data for all connected MPX/MPH/MPH2/IMS
systems.
– Operated with a navigation switch.
– Connected via a cable with the RPC, enabling
the user to place the displays where needed in
the given local space conditions.
– An individual display can be used for up to
four MPX/MPH/MPH2/IMS PDUs, which are all
connected in a PDU array.
L
224 | Rack PDUs
W
H
U
Model
Note
The display module is not required for operating
the MPX or MPH, MPH2, IMS. However, a
communication card is needed.
Standard inclusion
– 1 x RPCBDM-1000 display module.
– 1 x connection cable 2 m.
– 1 x mounting kit.
Order No.
UP
RPCBDM-1000
1 unit
MPH2™
SafetyLock™ Connection Cable IEC C13 EU
– Connection cables have
integrated protection against
accidental disconnection.
– For straight locking from C14 to C13.
– Locking cables are sold in sets of 9 units.
Certification
– ENEC.
– VDE.
– CB scheme.
– RoHS compliant.
DOS20495
Technical data
– Standard: IEC 60320.
– Load rating: 250 Vac/10 A.
– Operating temperature: -25° C ~ +70° C.
– Extraction force with locking function:
up to 120 N.
– Electric power cable: H05VV-F 3G 1.0 mm2.
– Flame retardance: Plug: UL 94V-2 or
better; cable: UL VW-1, IEC60332-1. Cat F2.
Color
– Black/white.
– Other colors available upon request.
Standard inclusion
– 9 x locking cables.
Delivery
– In sets.
DOS20496
L
Model
Order No.
UP
0.5 m
Black
03.951.450.0,001
9 unit
1.0 m
Black
03.951.450.0,002
9 unit
1.5 m
Black
03.951.450.0,003
9 unit
0.5 m
White
03.951.451.0,001
9 unit
1.0 m
White
03.951.451.0,002
9 unit
1.5 m
White
03.951.451.0,003
9 unit
DOS20497
SafetyLock™ Connection Cable IEC C19 EU
– Connection cables have
integrated protection against
accidental disconnection.
– For straight locking from C20 to C19.
– Locking cables are sold in sets of 6 units.
Approvals
– ENEC.
– VDE.
– CB scheme.
– RoHS compliant.
DOS20498
Technical data
– Standard: IEC 60320.
– Load rating: 250 Vac/16 A.
– Operating temperature: -25° C ~ +70° C.
– Extraction force with locking function:
up to 120 N.
– Electric power cable: H05VV-F 3G 1.5 mm2.
– Flame retardance: Plug: UL 94V-2 or
better; cable: UL VW-1, IEC60332-1. Cat F2.
Color
– Black/white.
– Other colors available upon request.
Standard inclusion
– 6 x locking cables.
Delivery
– In sets.
DOS20499
L
Model
Order No.
UP
0.5 m
Black
03.951.455.0,001
6 unit
1.0 m
Black
03.951.455.0,002
6 unit
1.5 m
Black
03.951.455.0,003
6 unit
0.5 m
White
03.951.456.0,001
6 unit
1.0 m
White
03.951.456.0,002
6 unit
1.5 m
White
03.951.456.0,003
6 unit
DOS20500
Rack PDUs | 225
DI-STRIP®
DI-STRIP® – Basic Rack-PDU
Robust PDUs with useful equipment features
Features
Closed sheet-steel extrusions and
ideal integration into Knürr rack
systems deliver high stability and
torsional strength.
Best possible conductivity: Fulllength brass busbar provided with
many models.
Double spring contacts for reliable
and low contact resistance.
226 | Rack PDUs
Emerson Network Power’s Basic Rack PDUs are the solution for every
data center looking for robust, economical and flexible rack concepts.
The DI-STRIP product family meets a broad range of data center power
distribution requirements for IT and other applications.
Specially configured for the growing number of electronic components in
network switching racks or server racks. Available with different accessories,
such as circuit breakers, overvoltage protection, mains filter, master-slave
function, emergency stop switch, fault-current circuit-breaker, local and remote
power metering.
DI-STRIP®
INPUT POWER
Single-phase or three-phase.
Up to 22 kVA.
Simple input supply.
OUTPUT DISTRIBUTOR
NEMA 5-20R single-phase, IEC C13 and C19,
combination systems.
Schuko, France, Switzerland.
MODULARITY
More connectivity with expansion unit for
Basic Rack PDU GST18.
FORM FACTOR
Vertical mounting (0 U).
Rack installation.
Workstation mounting.
LOCAL MONITORING
Fixed display.
1-1
10.3A
119.5V 4.32kW 5.17kVA
12345
REMOTE MONITORING
Secure Web and SNMP interfaces
with Liebert Nform.
OVERLOAD PROTECTION
Circuit breakers/fuses per branching
cable/output as required.
DI-STRIP®
Benefits
Optimal phase distribution
across the entire rack with
color-coded identification
of the individual phases.
Up to 48 different plug options
per PDU: shortens the cable
distance between the PDU and
the consumer.
One of the most compact PDUs
on the market: measures only
44.4 x 45.5 mm, which saves space
ace
even on a 600 mm-wide rack.
Simple and quick installation
on the rack extrusion: reduces
installation and wiring costs.
228 | Rack PDUs
DI-STRIP®
Highest possible security and availability with:
Closed sheet-steel extrusions that deliver high stability
and torsional flexibility.
Extensive certification compliant with the international
Standard.
Double spring contacts for reliable and low contact
resistance.
Unbalanced load monitoring prevents feed-cable overload of 3-phase feed (only DI-STRIP versions M and RM).
Optimal load monitoring for server installation
(only DI-STRIP versions M and RM).
Individual output-backup with DI-STRIP BladePower
and Pizza Power.
Reliable power distribution at full power delivered by full-length brass busbars.
A
Maximum flexibility attained due to:
Internationally compatible configurations and options.
Power cable lengths of 2.5 m or 4 m for more spatial
flexibility.
Rotating current indicator in 90° steps
(only M and RM DI-STRIP versions).
Tool-less installation, which means quick and easy
extension in the rack (only with DI-STRIP HighPower).
Extremely low operating costs:
Installation in the rack is rapid and easy requiring
minimal space and reduced installation time.
Automatic background-light reduction reduces the rack
PDU power loss (only with M and RM DI-STRIP versions).
Especially flat housing extrusion, providing full accessibility to the 19" level on 600 mm wide server racks.
B
C
Can be fitted to a rack or workstation.
Highly compact construction; minimizes space requirements in the rack.
Color-coded phase allocation (L1, L2, L3).
Rack PDUs | 229
DI-STRIP®
DI-STRIP®
European Equipment Models
DI-STRIP models
Functions
Input power
Outputs
Technical description
Euro socket system IEC 320
Basic power distribution
1 x 16 A
3.68 kVA
IEC60320
C13 & C19
Page 253
TriplePower
Basic power distribution
3 x 16 A
11 kVA
IEC60320
C13 & C19 & Schuko
Page 253
PizzaPower
Basic power distribution
1 x 32 A, 3 x 32 A
7.36 kVA, 22 kVA
IEC60320
C13 & C19 & Schuko
Page 254
BladePower
Basic power distribution
1 x 32 A, 3 x 32 A
7.36 kVA, 22 kVA
IEC60320
C13 & C19
Page 254
HighPower
Basic power distribution
1 x 32 A, 3 x 32 A
7.36 kVA, 22 kVA
IEC60320
C13 & C19
Page 255
Classic
Basicpower distribution/extra
large distance between the sockets
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 255
Compact
Basic power distribution
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 256
Protector FI
Fault-current circuit-breaker
FI
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 256
Protector LS
Circuit breaker (LS)
FI
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 257
Protector FI/LS
Combination FI + LS
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 257
Protector Emergency Stop
Emergency stop switch
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 258
Protector Emergency Stop FI/LS
Combination emergency stop + FI + LS
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 258
Power Cleaner
Mains filter
1 x 16 A
3.68 kVA
Schuko, France
Page 259
Safety Basic
Overvoltage protection
1 x 16 A
3.68 kVA
Safety Standard
Mains filter + overvoltage protection
1 x 16 A
3.68 kVA
Schuko, France, Switzerland
Page 260
Master Slave
Master Slave
1 x 16 A
3.68 kVA
Schuko, France
Page 261
Combi
Combination Master Slave +
overvoltage protection + mains filter
1 x 16 A
3.68 kVA
Schuko, France
Page 261
M (metered)
Phase current metered reading, local
1 x 16 A, 1 x 32 A, 3 x 16 A
3.32 A to 22 kVA
IEC60320
C13 & C19 & Schuko
Page 262
RM (remote metered)
Phase current metered reading local +
remote
1 x 16 A, 1 x 32 A, 3 x 16 A
3.32 A to 22 kVA
IEC60320
C13 & C19 & Schuko
Page 262
230 | Rack PDUs
Schuko, France, Switzerland
Page 259
DI-STRIP®
DI-STRIP® Euro Socket System, IEC 320
DOS00458
– Optionally with illuminated switch; 2-pole
switching.
– 19" installation option.
– Euro socket combinations of IEC 320 C13 and
C19 sockets.
– Feed cable: H05VV-F 3G 1.5/2.5 mm2.
– Feed cable: 2.5 m / 5 m.
DOS00460
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
DOS20062
Dimensions
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
– CSA (only models with IEC60320 input).
Color
– Enclosure: RAL 7035, light-gray.
– Plastic parts: RAL 7021 dark-gray.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
DOS20102
DI-STRIP® TriplePower® Euro Socket System
– Feed cable: H05VV-F 5 G 2.5 mm2.
– Feed cable: 2.5 m (optional with IEC60309 plug,
3Ph/N/PE 6h).
– Easy mounting on the rack extrusion.
– Standard feed 3 x 16 A.
– Ideal for implementing redundancy
(e.g. 96 A with redundant feed).
– Color-coded phase allocation.
– Optimum distribution across the entire
rack height (23 U and 41 U).
– Alternative to 3-phase GST18 system.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
– IEC 320.
Color
– Enclosure: RAL 7035, light-gray.
– Plastic parts: RAL 7021 dark-gray.
DOS20126
Material/ Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
Load rating
– 100-240/173-415 Vac.
– Input: 3 x 16 A.
– Output: 10 A (C13).
– Output: 16 A (C19 / Schuko).
Dimensions
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Rack PDUs | 231
DI-STRIP®
Knürr DI-STRIP® PizzaPower®
– Individually fused thermal circuit breaker
that can be reset in accorandance with
IEC60934.
– Feed cable: H05VV-F 5 G 4 mm2.
– Feed cable: 4 m.
Certification
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG (only without plug).
DOS20158
Material / Finish
– Enclosure: sheet steel, zinc passivated,
powder-coated.
Dimensions
– Height: approx. 60 mm.
– Width of housing: 84 mm.
– Height with cable: approx. 176 mm.
DOS20159
Color
– Enclosure: RAL 9005, black.
Load rating
– 100-240 / 173-415 Vac.
– Input: 1 x 32 A or 3 x 32 A.
– Output: 10 A (C13).
– Output: 16 A (C19).
Standard inclusion
– 1 x socket strip (PDU).
– 2 x mounting brackets.
– 1 x 19" mounting bracket (additionally with
19" installation option).
– 1 x instruction manual.
Knürr DI-STRIP® BladePower®
DOS20153
– IEC 320 sockets (10 A and 16 A).
– Individually fused via thermal circuit breaker
that can be reset in accorandance with
IEC 60934.
– Feed cable: H05VV-F 5 G 4 mm2.
– Feed cable: 4 m.
– With IEC60309 plug, 1Ph/N/PE 6h blue,
3Ph/N/PE 6h red.
Material / Finish
– Housing: sheet steel, zinc passivated,
powder-coated.
DOS20155
Dimensions
– Height: approx. 60 mm.
– Width of housing: 84 mm.
Color
– Enclosure: RAL 9005, black.
232 | Rack PDUs
Approvals
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV GS.
– CSA NRTL/C (only without plug).
Load rating
– 100-240 / 173-415 Vac.
– Input: 1 x 32 A or 3 x 32 A.
– Output: 10 A / 16 A.
Standard inclusion
– 1 x socket strip (PDU).
– 2 x mounting brackets.
– 1 x 19" mounting bracket (additionally with
19" installation option).
– 1 x instruction manual.
DI-STRIP®
Knürr DI-STRIP® HighPower
DOS20153
– Flat design provides easy access to
the 19" level, even with 600 mm-wide racks.
– Individual backup for outputs (10 A groups).
– Outputs divided into groups with max.
20 A per group.
– Modular expansion in the rack with tool-less
PDU installation.
Additional functions for HighPower RM type
(remote metering).
– Large LCD display with ample overview.
– Displays real energy reading of alternating
current input.
-– LCD display rotation in 90° steps.
– Display contrast can be adjusted.
– Signals indicate load changes.
– Automatic reduction of background light.
– Technical description of data interface
(see DI-STRIP RM).
Material / Finish
– Enclosure: sheet steel, zinc passivated,
powder-coated.
Dimensions
– Width: 134 mm.
– Height: 47 mm.
– Feed cable: 3 m.
Color
– Housing: RAL 9005 black.
Certification
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
Standard inclusion
– 1 x socket strip (PDU).
– 1 x 1 integrated remote ampere meter
(only HighPower RM).
– 2 x mounting brackets.
– 1 x instruction manual.
Knürr DI-STRIP® Classic
DOS00403
– Optionally with illuminated switch; 2-pole
switching.
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Optionally with Euro plug, IEC320 for UPS
application.
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94).
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 100 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
– VDE GS.
Color
– RAL 7035, light-gray.
Load rating
– 100-240 Vac/16 A (output Schuko and UTE).
– 100-240 Vac/10A (outputs Switzerland).
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Rack PDUs | 233
DI-STRIP®
Knürr DI-STRIP® Compact
DOS00401
with switch.
– Optionally with illuminated switch; 2-pole
switching.
– 19" installation option (for length 483 mm).
– 2 versions: standard side panel or design side
panel.
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
– Optionally with Euro plug, IEC320 for UPS
applications.
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
– VDE GS.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Final digit of order number .6:
housing RAL 2003 pastel orange.
– Plastic parts: RAL 7035, light-gray.
Load rating
– 100-240 Vac/16 A (output Schuko and UTE).
– 100-240 Vac/10 A (outputs Switzerland).
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Knürr DI-STRIP® Protector FI
DOS20065
with FI circuit breaker
Protector FI
– Fault-current circuit breaker for user
protection.
– Protection against indirect contact by
disconnection of the circuit when inadmissibly
high contact voltage occurs through bodily
contact with electrical equipment.
– Additional protection against direct contact.
– Residual operating current Ig = 10 mA for
alternating and pulsating direct fault currents.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material/ Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 78 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Plastic parts: RAL 7035, light gray.
Load rating
– 100–240 Vac/16 A.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
234 | Rack PDUs
DI-STRIP®
Knürr DI-STRIP® Protector LS
DOS00692
with circuit breaker.
Protector LS
– Circuit breaker for overload and short circuit.
– Protects cables and lines by switching off
rapidly in the event of a short circuit and
defined delayed switch-off when overloads
occur.
– Circuit breaker: 16 A.
– Trip characteristics: type B, 2-pole.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
– VDE GS.
Material/ Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Load rating
– 100–240 Vac/16 A.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Plastic parts: RAL 7035, light gray.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Dimensions
– Distance between sockets: 50 mm.
– Height: 78 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Knürr DI-STRIP® Protector FI / LS
DOS00693
Protector FI / LS
– Fault current switch and circuit breaker.
– Provides a combination of user, overload and
short circuit protection.
– Residual operating current Ig = 30 mA for
alternating and pulsating direct fault currents.
– Circuit breaker 16 A (Schuko and France) /
10A (Switzerland).
– Trip characteristics, type B, 2-pole.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 78 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Plastic parts: RAL 7035, light-gray.
Load rating
– 100–240 Vac/16 A (Schuko and France).
– 100–240 Vac/10 A (Switzerland).
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Rack PDUs | 235
DI-STRIP®
Knürr DI-STRIP® Protector Emergency Stop
DOS20059
– With 2-pole emergency stop switch for
user protection.
– For manually disconnecting consumers in
an emergency.
– Phase and neutral conductors are separated
safely.
– Switch must be intentionally unlocked to
restart.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combinations
– Final digit of order number .1:
RAL 7035, light gray.
– Plastic parts: RAL 7035, light gray.
Load rating
– 100–240 Vac/16 A.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Dimensions
– Distance between sockets: Classic: 100 mm,
Compact: 50 mm.
– Height: 101 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Knürr DI-STRIP® Protector Emergency Stop FI /LS
DOS00456
– With 2-pole emergency stop switch
for user protection.
– For protecting operating personnel.
– For manually disconnecting consumers in
an emergency.
– Phase and neutral conductors are separated
safely.
– Switch must be intentionally unlocked to
restart.
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material/ Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: Compact: 50 mm.
– Height: 101 mm.
– Width of housing: 44.4 mm (= 1 U)
– Feed cable: 2.5 m.
236 | Rack PDUs
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combinations
– Final digit of order number .1:
RAL 7035, light-gray.
– Plastic parts: RAL 7035, light-gray.
Additionally:
– With 2-pole fault-current switch and circuit
breaker
– Provides a combination of user, overload and
short circuit protection.
Load rating
– 100–240 Vac/16 A.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
DI-STRIP®
Knürr DI-STRIP® Power Cleaner
– High-frequency glitches generally occur
in switching processes ranging from 100 kHz to
5 MHz. This high-frequency rate overloads the
mains frequency and affects adjacent electronic
equipment. The mains filter attenuates this
high-frequency rate.
– The attenuation behavior is harmonized with
the typical interference spectrum.
– The mains filter works in both directions: where
glitches from the equipment to the socket strip
are also filtered from the mains.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
DOS20061
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Final digit of order number .6:
housing RAL 2003 pastel orange.
– Plastic parts: RAL 7035, light-gray.
Technical data
– Nominal voltage: max. 250 Vac, 50 Hz.
– Nominal current, max. 16 A.
– Filter compliant with VDE 0565-3
(EN 60939-1).
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
– 2 x 19" mounting brackets (additionally with
19" installation option).
Knürr DI-STRIP® Safety Basic
DOS20068
with overvoltage protection
– For protection against transient overvoltage
from the mains, which, for example, are caused
by switching machines on and off.
– When critical overvoltages occur, the connection to the mains is cut off.
– Once the protective conductor has been triggered, the green function display light is not
illuminated. Thus, the socket strip can no longer
be used.*
– Basic equipment protection is classified as class
3 (category D).
– For optimal protection, class 1 and 2 (categories
B and C) protective equipment must be installed in the building.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Final digit of order number .6:
housing RAL 2003 pastel orange.
– Plastic parts: RAL 7035, light-gray.
Technical data
– Appliance class: Type 3 as per DIN EN 61643-11.
– Requirement class: category D as per VDE
0675-6.
– Mains voltage: 230 VAC.
– Nominal current, max. 16 A.
– Discharge surge current (8/20 μs): 10 kA.
– Reaction time: ‹ 25 ns.
– Safety level (at 100 A varistor peak current):
L with respect to N: ‹ 800 V, L / N with respect to
PE: ‹ 1500 V.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
* Send the socket strip to the manufacturer for the protective conductor to be replaced!
Rack PDUs | 237
DI-STRIP®
Knürr DI-STRIP® Safety Standard
DOS20069
– Standard safety models consist of a combined
overvoltage protection/mains filter element.
– Protects against transient overvoltages from
the mains, which, for example, are caused by
switching machines on and off.
– When critical overvoltages occur, connection to
the mains is cut off.
– Once the protective conductor has been
triggered, the green function display light is not
illuminated. The socket strip can thus no longer
be used.*
– Basic equipment protection is classified as class
3 (category D).
– For optimal protection, class 1 and 2 (categories
B and C) protective equipment must be
installed in the building.
– High-frequency glitches are generally caused
by switching processes in an operation from
100 kHz to 5MHz.
– This high-frequency rate overloads the mains
frequency and affects adjacent electronic
equipment. The mains filter attenuates this
high-frequency rate.
– The attenuation behavior is harmonized with
the typical interference spectrum.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: HO5VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material/ Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Final digit of order number .6:
housing RAL 2003 pastel orange.
– Plastic parts: RAL 7035, light-gray.
Technical data
– Mains voltage: 230 VAC.
– Nominal current: max. 16 A / 10 A.
– Discharge surge current (8/20 μs): 10 kA.
– Reaction time: ‹ 25 ns.
– Safety level (at100 A varistor peak current):
L with respect to N: ‹ 800 V, L / N with respect
to PE: ‹ 1500 V.
– Overvoltage protection
– Appliance class: Class 3 – as per
DIN EN 61643-11.
– Requirement class: Category D as per
VDE 0675-6.
– Mains filter: as per VDE 0565 (EN 60939).
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
* Send the socket strip to the manufacturer for the safety arrester to be replaced!
238 | Rack PDUs
DI-STRIP®
Knürr DI-STRIP® Master-Slave
– Slave plugs will switch on if master switches on.
– Note:
– The master consumer's power intake must
always exceed the switch-on threshold. When
switching off the master consumer, the power
intake must fall below the switch-off threshold.
– 19" installation option (for length 483 mm).
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
DOS20070
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
– VDE GS.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Plastic parts: RAL 7035, light-gray.
Load rating
– Max. 250 Vac/16 A.
Technical data
– Switching-threshold setting range
– On: 20 - 200 mA (approx. 55 mA on delivery).
– Off: 16 - 160 mA (approx. 44 mA on delivery).
– Switching delay: 550 ms, ± 20 %.
– Electronic module: 2-pole switching.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Knürr DI-STRIP® Combi
DOS00325
with master-slave overvoltage protection
and mains filter.
– Master-slave with overvoltage protection and
mains filter.
– Automatic consumer switching.
– Combines Master-Slave (page 261) and Safety
Standard (page 260) functions.
– Socket rotation: 45°.
– Feed cable: H05VV-F 3G 1.5 mm2.
– Molded right angle plug.
Material / Finish
– Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
– Internal conductor: full-length busbars, brass.
Dimensions
– Distance between sockets: 50 mm.
– Height: 45.5 mm.
– Width of housing: 44.4 mm (= 1 U).
– Feed cable: 2.5 m.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
– CB scheme.
Color combination
– Final digit of order number .1:
RAL 7035, light-gray.
– Plastic parts: RAL 7035, light-gray.
Technical data
– With overvoltage protection and mains filter.
– Mains voltage: max. 250 Vac.
– Nominal current: 16 A.
– Requirement class: D (protection as per
VDE 0675).
– Surge current resistance (8/20 μs wave):
Max. 10 kA.
– Protection level (1.5/50 μs wave):
‹ 1500 V (L + N against PE).
– Master-slave function:
– Switching-threshold setting range
– On: 20 - 200 mA (approx. 55 mA on
delivery).
– Off: 16 - 160 mA (approx. 44 mA on
delivery).
– Switching delay: 550 ms ± 20 %.
– Electronic module: 2-pole switching.
Standard inclusion
– 1 x socket strip.
– 2 x mounting brackets.
Rack PDUs | 239
DI-STRIP®
Knürr DI-STRIP® M
DOS80002
– Large LCD display for clear view.
– Effective metering of alternating current
displayed per phase (single-phase or 3-phase,
depending on model).
– LCD display rotation in 90° steps.
– Display contrast can be adjusted.
– Unbalanced-load warning display with 3-phase
model.
– Signals indicate load changes.
– Automatic reduction of background light.
– Feed cable: 4 m H05VV—F 5 G 4 mm2
(PizzaPower M).
– Feed cable: 2.5 m H05VV-F 5 G 2.5 mm2
(TriplePower M).
– Feed cable: 2.5 m H05VV-F 3G 1.5 mm2
(DI-STRIP Compact M, DI-STRIP IEC320 M).
Material/ Finish
– PizzaPower® model; Housing: sheet steel,
zinc-passivated, powder-coated.
– Other models: Housing: closed sheet steel
extrusion, zinc-passivated, powder-coated
texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
Approvals/certificates
– CE label in accordance with
Low Voltage Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
EN61326-1, EN61000-3-2, EN61000-3-3.
– FCC Class B.
– CB scheme (TriplePower M, DI-STRIP compact
M, IEC320M, ampere meter GST18i).
Color
– PizzaPower M model; Housing:
RAL 9005 black.
– Other models; Housing:
RAL 7035 light-gray.
– Plastic parts: RAL 7021 dark-gray.
Standard inclusion
– 1 x socket strip with ampere meter.
– 2 x mounting brackets.
– 2 x 19" mounting brackets (with 19"
installation option).
Note
Other models (e.g C 19 outputs)
available on request.
Knürr DI-STRIP® RM
DOS80002
240 | Rack PDUs
– Displays real RMS value for the
alternating current per phase.
– LCD display rotation in 90° steps.
– Display bright/dark switchover.
– Warning display for unbalanced load.
– Signals indicate load changes.
– Automatic darkening of background light
for energy saving.
Material / Finish
– PizzaPower model; Housing: sheet steel,
zinc-passivated, powder-coated.
– Other models; Housing: closed sheet steel
extrusion, zinc-passivated, powder-coated
texture.
– Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable.
Data interface:
– The plug strip can be integrated into the
network via an RJ45 plug.
– Access is possible without special software
via a remote browser.
– Three variable limit values and a warning for
unbalanced loads can be specified.
– The module enables access for up to 5 users or
administrators; access is password-protected.
– The software displays the name and location of
the PDU; this information can be entered by an
administrator.
– The user can specify a static IP address or access
using DHCP.
– Firmware updates can be made via a web
browser.
– Supported protocols: HTTP, SNMP (Traps, SET,
GET), Syslog.
Dimensions
– Width: 84 mm (PizzaPower), 44.4 mm
(others).
– Height: 60 mm (PizzaPower), 44.4 mm
(others).
Color
– PizzaPower model; Housing: RAL 9005 black.
– Other models; Housing: RAL 7035 light-gray.
– Plastic parts: RAL 7021 dark-gray.
Approvals
– CE label in accordance with Low Voltage
Directive 2006/95/EC.
– EMC Directive 2004/108/EC.
– BV BG.
Standard inclusion
– 1 x socket strip (PDU) with remote ampere
meter.
– 1 x mounting bracket.
– 1 x instruction manual.
DI-STRIP®
DI-STRIP Model
Input Values
Voltage
Input Connector
Current
Outputs
C13
C19
Schuko
L
UTE
S
F1
F2
19"
Safe
Order No.
Type 13
Euro plug IEC320 system (technical description on page 231)
With feed cable
Euro input in plug
panel
Euro input on side
panel
230V
16 A
Schuko CEE7/7
6
333
03.600.006.1
230V
16 A
Schuko CEE7/7
9
483
03.602.009.1
230V
10 A
IEC60320 C13
12
483
03.600.312.1
230V
16 A
IEC60320 C19
15
3
783
03.600.418.1
230V
16 A
IEC60309 1ph/N/PE 6h
15
3
783
03.600.518.1
230V
10 A
IEC60320 C14 inlet
6
383
03.622.006.1
230V
10 A
IEC60320 C14 inlet
9
483
03.622.009.1
230V
10 A
IEC60320 C14 inlet
6
433
03.624.006.1
230V
10 A
IEC60320 C14 inlet
6
333
03.622.706.1
230V
10 A
IEC60320 C14 inlet
9
433
03.622.709.1
230V
10 A
IEC60320 C14 inlet
6
383
03.624.706.1
230V
10 A
IEC60320 C14 inlet
9
483
03.624.709.1
10
483
03.632.010.1
GST18
6
383
03.600.206.1
With overload
protection 10 A
230V
10 A
GST18 input
in side panel
230V
16 A
Schuko CEE7/7
TriplePower (technical description on page 231)
230/400V
3 x 16 A
none
24
1033
03.600.024.1
230/400V
3 x 16 A
none
48
1833
03.600.048.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
24
1033
03.600.824.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
48
1833
03.600.848.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
18
6
1133
03.600.524.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
36
6
1733
03.600.542.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
6
483
03.600.506.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
833
03.300.812.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
18
833
03.600.521.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
18
833
03.300.521.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
21
833
03.600.821.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
45
1733
03.600.845.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
36
1733
03.300.542.1
12
3
3
6
PizzaPower (technical description on page 232)
230V
32 A
IEC60309 1ph/N/PE 6h
7
400
03.631.007.1
230V
32 A
none
7
400
03.631.807.1
230V
32 A
IEC60309 1ph/N/PE 6h
12
720
03.631.124.1
230V
32 A
IEC60309 1ph/N/PE 6h
24
960
03.631.240.1
230V
32 A
IEC60309 1ph/N/PE 6h
21
1017
03.631.214.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
21
933
03.631.021.1
230/400V
3 x 32 A
none
21
933
03.631.821.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
6
408
03.631.006.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
9
12
939
03.631.912.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
36
1362
03.631.360.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
18
1002
03.631.186.1
4
4
6
BladePower (technical description on page 232)
230V
32 A
IEC60309 1ph/N/PE 6h
2
3
375
03.630.005.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
6
9
740
03.630.015.1
230V
32 A
none
2
3
375
03.630.805.1
230/400V
3 x 32 A
none
6
9
740
03.630.815.1
HighPower (technical description on page 233)
With RM
metering
module
230V
32 A
IEC60309 1ph/N/PE 6h
20
4
540
03.632.100.8
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
6
12
850
03.632.102.8
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
18
6
850
03.632.103.8
230V
32 A
IEC60309 1ph/N/PE 6h
20
4
540
03.632.200.8
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
6
12
850
03.632.202.8
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
18
6
850
03.632.203.8
Rack PDUs | 241
DI-STRIP®
DI-STRIP Model
Input Values
Voltage
Input Connector
Current
Outputs
C13
C19
Schuko
L
UTE
S
F1
F2
19"
Safe
Order No.
Type 13
Classic (technical description on page 233)
230V
16 A
Schuko CEE7/7
17
1783
03.300.067.X
230V
16 A
Schuko CEE7/7
13
1383
03.300.063.X
230V
16 A
Schuko CEE7/7
9
983
03.300.059.X
230V
16 A
Schuko CEE7/7
5
583
03.300.055.X
230V
16 A
Schuko CEE7/7
16
1733
03.302.066.X
230V
16 A
Schuko CEE7/7
12
1333
03.302.062.X
230V
16 A
Schuko CEE7/7
8
933
03.302.058.X
230V
16 A
Schuko CEE7/7
4
533
03.302.054.X
230V
16 A
Schuko CEE7/7
17
1783
03.400.067.X
230V
16 A
Schuko CEE7/7
13
1383
03.400.063.X
230V
16 A
Schuko CEE7/7
9
983
03.400.059.X
230V
16 A
Schuko CEE7/7
5
583
03.400.055.X
230V
16 A
Schuko CEE7/7
16
1733
03.402.066.X
230V
16 A
Schuko CEE7/7
12
1333
03.402.062.X
230V
16 A
Schuko CEE7/7
8
933
03.402.058.X
230V
16 A
Schuko CEE7/7
4
533
03.402.054.X
230V
10 A
SEV 1011 T12
17
1783
03.700.067.X
230V
10 A
SEV 1011 T12
13
1383
03.700.063.X
230V
10 A
SEV 1011 T12
9
983
03.700.059.X
230V
10 A
SEV 1011 T12
5
583
03.700.055.X
230V
10 A
SEV 1011 T12
16
1733
03.702.066.X
230V
10 A
SEV 1011 T12
12
1333
03.702.062.X
230V
10 A
SEV 1011 T12
8
933
03.702.058.X
230V
10 A
SEV 1011 T12
4
533
03.702.054.X
Compact (technical description on page 234)
UPS application
230V
16 A
Schuko CEE7/7
15
883
03.300.015.X
230V
16 A
Schuko CEE7/7
11
732
03.300.111.X
230V
16 A
Schuko CEE7/7
11
683
03.300.011.X
230V
16 A
Schuko CEE7/7
7
532
03.301.107.X
230V
16 A
Schuko CEE7/7
7
532
03.300.107.X
230V
16 A
Schuko CEE7/7
7
483
03.300.007.X
230V
16 A
Schuko CEE7/7
8
483
03.300.008.1
230V
16 A
Schuko CEE7/7
4
382
03.301.104.X
230V
16 A
Schuko CEE7/7
4
382
03.300.104.X
230V
16 A
Schuko CEE7/7
4
333
03.300.004.X
230V
16 A
Schuko CEE7/7
14
883
03.302.014.X
230V
16 A
Schuko CEE7/7
10
732
03.302.110.X
230V
16 A
Schuko CEE7/7
10
683
03.302.010.X
230V
16 A
Schuko CEE7/7
6
532
03.303.106.X
230V
16 A
Schuko CEE7/7
6
532
03.302.106.X
230V
16 A
Schuko CEE7/7
6
483
03.302.006.X
230V
16 A
Schuko CEE7/7
7
483
03.302.007.1
230V
16 A
Schuko CEE7/7
3
382
03.303.103.X
230V
16 A
Schuko CEE7/7
3
382
03.302.103.X
230V
16 A
Schuko CEE7/7
3
333
03.302.003.X
230V
10 A
IEC60320 C14
8
483
03.300.308.1
230V
16 A
IEC60320 C20
8
483
03.300.408.1
230V
16 A
GST18
6
583
03.302.206.1
230V
16 A
GST18
3
433
03.302.203.1
230V
16 A
GST18
7
533
03.300.207.1
230V
16 A
GST18
4
383
03.300.204.1
230V
16 A
Schuko CEE7/7
15
883
03.400.015.X
230V
16 A
Schuko CEE7/7
11
732
03.400.111.X
230V
16 A
Schuko CEE7/7
11
683
03.400.011.X
230V
16 A
Schuko CEE7/7
7
532
03.400.107.X
242 | Rack PDUs
DI-STRIP®
DI-STRIP Model
Input Values
Voltage
Input Connector
Current
Outputs
C13
C19
Schuko
L
UTE
S
F1
F2
19"
Safe
Order No.
Type 13
Compact (technical description on page 234)
230V
16 A
Schuko CEE7/7
7
483
03.400.007.X
230V
16 A
Schuko CEE7/7
4
382
03.400.104.X
230V
16 A
Schuko CEE7/7
4
333
03.400.004.X
230V
16 A
Schuko CEE7/7
14
883
03.402.014.X
230V
16 A
Schuko CEE7/7
10
732
03.402.110.X
230V
16 A
Schuko CEE7/7
10
683
03.402.010.X
230V
16 A
Schuko CEE7/7
6
532
03.402.106.X
230V
16 A
Schuko CEE7/7
6
483
03.402.006.X
230V
16 A
Schuko CEE7/7
3
382
03.402.103.X
230V
16 A
Schuko CEE7/7
3
333
03.402.003.X
230V
16 A
GST18
6
583
03.402.206.1
230V
16 A
GST18
3
433
03.402.203.1
230V
16 A
GST18
7
533
03.400.207.1
230V
16 A
GST18
4
383
03.400.204.1
230V
10 A
SEV 1011 T12
15
883
03.700.015.X
230V
10 A
SEV 1011 T12
11
732
03.700.111.X
230V
10 A
SEV 1011 T12
11
683
03.700.011.X
230V
10 A
SEV 1011 T12
7
532
03.700.107.X
230V
10 A
SEV 1011 T12
7
483
03.700.007.X
230V
10 A
SEV 1011 T12
4
382
03.700.104.X
230V
10 A
SEV 1011 T12
4
333
03.700.004.X
230V
10 A
SEV 1011 T12
10
732
03.702.110.X
230V
10 A
SEV 1011 T12
10
683
03.702.010.X
230V
10 A
SEV 1011 T12
6
532
03.702.106.X
230V
10 A
SEV 1011 T12
6
483
03.702.006.X
230V
10 A
SEV 1011 T12
3
382
03.702.103.X
230V
10 A
SEV 1011 T12
3
333
03.702.003.X
Protector FI (technical description on page 234)
230V
16 A
Schuko CEE7/7
13
883
03.304.013.1
230V
16 A
Schuko CEE7/7
9
683
03.304.009.1
230V
16 A
Schuko CEE7/7
5
483
03.304.005.1
230V
16 A
Schuko CEE7/7
13
883
03.404.013.1
230V
16 A
Schuko CEE7/7
9
683
03.404.009.1
230V
16 A
Schuko CEE7/7
5
483
03.404.005.1
Protector LS (technical description on page 235)
230V
16 A
Schuko CEE7/7
13
883
03.308.013.1
230V
16 A
Schuko CEE7/7
9
683
03.308.009.1
230V
16 A
Schuko CEE7/7
5
483
03.308.005.1
230V
16 A
Schuko CEE7/7
13
883
03.408.013.1
230V
16 A
Schuko CEE7/7
9
683
03.408.009.1
230V
16 A
Schuko CEE7/7
5
483
03.408.005.1
Protector FI/LS (technical description on page 235)
230V
16 A
Schuko CEE7/7
13
883
03.310.013.1
230V
16 A
Schuko CEE7/7
9
683
03.310.009.1
230V
16 A
Schuko CEE7/7
5
483
03.310.005.1
230V
16 A
Schuko CEE7/7
13
883
03.410.013.1
230V
16 A
Schuko CEE7/7
9
683
03.410.009.1
230V
16 A
Schuko CEE7/7
5
483
03.410.005.1
230V
10 A
SEV 1011 T12
9
683
03.710.009.1
230V
10 A
SEV 1011 T12
5
483
03.710.005.1
Protector emergency stop switch (technical description on page 236)
Compact
230V
16 A
Schuko CEE7/7
10
683
03.326.010.1
230V
16 A
Schuko CEE7/7
6
483
03.326.006.1
230V
16 A
Schuko CEE7/7
10
683
03.426.010.1
230V
16 A
Schuko CEE7/7
6
483
03.426.006.1
Rack PDUs | 243
DI-STRIP®
DI-STRIP Model
Input Values
Voltage
Input Connector
Current
Outputs
C13
C19
Schuko
L
UTE
S
F1
F2
19"
Safe
Order No.
Type 13
Protector emergency stop switch (technical description on page 236)
Classic
230V
16 A
Schuko CEE7/7
12
1333
03.326.062.1
230V
16 A
Schuko CEE7/7
8
933
03.326.058.1
230V
16 A
Schuko CEE7/7
12
1333
03.426.062.1
230V
16 A
Schuko CEE7/7
8
933
03.426.058.1
683
03.328.008.1
683
03.428.008.1
Protector emergency stop switch FI/LS (technical description on page 236)
230V
16 A
Schuko CEE7/7
230V
16 A
Schuko CEE7/7
8
8
Power Cleaner (technical description on page 237)
230V
16 A
Schuko CEE7/7
13
883
03.312.013.X
230V
16 A
Schuko CEE7/7
9
683
03.312.009.X
230V
16 A
Schuko CEE7/7
5
483
03.312.005.X
230V
16 A
GST18
230V
16 A
Schuko CEE7/7
230V
16 A
230V
16 A
6
483
03.612.206.1
13
883
03.412.013.X
Schuko CEE7/7
9
683
03.412.009.X
Schuko CEE7/7
5
483
03.412.005.X
Safety Basic (technical description on page 237)
230V
16 A
Schuko CEE7/7
10
732
03.316.110.1
230V
16 A
Schuko CEE7/7
10
683
03.316.010.X
03.317.106.1
230V
16 A
Schuko CEE7/7
6
532
230V
16 A
Schuko CEE7/7
6
532
03.316.106.1
230V
16 A
Schuko CEE7/7
6
483
03.316.006.X
230V
16 A
Schuko CEE7/7
4
432
03.317.104.1
230V
16 A
Schuko CEE7/7
4
432
03.316.104.1
230V
16 A
Schuko CEE7/7
4
383
03.316.004.1
230V
16 A
GST18
4
433
03.316.204.1
230V
16 A
GST18
483
03.616.206.1
230V
16 A
Schuko CEE7/7
10
732
03.416.110.1
230V
16 A
Schuko CEE7/7
10
683
03.416.010.1
230V
16 A
Schuko CEE7/7
6
532
03.416.106.1
230V
16 A
Schuko CEE7/7
6
483
03.416.006.1
230V
16 A
Schuko CEE7/7
4
432
03.416.104.1
230V
16 A
Schuko CEE7/7
4
383
03.416.004.1
230V
16 A
GST18
4
433
03.416.204.1
6
Safety Standard (technical description on page 238)
230V
16 A
Schuko CEE7/7
13
883
03.318.013.X
230V
16 A
Schuko CEE7/7
9
732
03.319.109.X
230V
16 A
Schuko CEE7/7
9
732
03.318.109.X
230V
16 A
Schuko CEE7/7
9
683
03.318.009.X
230V
16 A
Schuko CEE7/7
5
532
03.319.105.X
230V
16 A
Schuko CEE7/7
5
532
03.318.105.X
230V
16 A
Schuko CEE7/7
5
483
03.318.005.X
230V
16 A
GST18
5
583
03.318.205.1
230V
16 A
GST18
230V
16 A
Schuko CEE7/7
230V
16 A
230V
16 A
230V
483
03.618.206.1
13
883
03.418.013.X
Schuko CEE7/7
9
732
03.418.109.X
Schuko CEE7/7
9
683
03.418.009.X
16 A
Schuko CEE7/7
5
532
03.418.105.X
230V
16 A
Schuko CEE7/7
5
483
03.418.005.X
230V
16 A
GST18
5
583
03.418.205.1
230V
10 A
SEV 1011 T12
9
683
03.718.009.X
230V
10 A
SEV 1011 T12
5
483
03.718.005.X
244 | Rack PDUs
6
DI-STRIP®
DI-STRIP Model
Input Values
Voltage
Input Connector
Current
Outputs
C13
C19
Schuko
L
UTE
S
F1
F2
19"
Safe
Order No.
Type 13
Master-Slave (technical description on page 239)
230V
16 A
Schuko CEE7/7
9
683
03.314.009.1
230V
16 A
Schuko CEE7/7
5
483
03.314.005.1
230V
16 A
GST18
5
533
03.314.205.1
230V
16 A
Schuko CEE7/7
9
683
03.414.009.1
230V
16 A
Schuko CEE7/7
5
483
03.414.005.1
230V
16 A
GST18
5
533
03.414.205.1
Combi (technical description on page 239)
230V
16 A
Schuko CEE7/7
9
782
03.320.109.1
230V
16 A
Schuko CEE7/7
9
733
03.320.009.1
230V
16 A
Schuko CEE7/7
5
582
03.321.105.1
230V
16 A
Schuko CEE7/7
5
582
03.320.105.1
230V
16 A
Schuko CEE7/7
5
533
03.320.005.1
230V
16 A
Schuko CEE7/7
9
782
03.420.109.1
230V
16 A
Schuko CEE7/7
9
733
03.420.009.1
230V
16 A
Schuko CEE7/7
5
582
03.420.105.1
230V
16 A
Schuko CEE7/7
5
533
03.420.005.1
M (technical description on page 240)
230V
32 A
IEC60309 1ph/N/PE 6h
7
483
03.636.007.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
21
933
03.636.021.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
21
1033
03.606.821.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
45
1833
03.606.845.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
18
6
1133
03.606.824.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
36
6
1733
03.606.842.1
230V
16 A
Schuko CEE7/7
483
03.306.006.1
230V
16 A
Schuko CEE7/7
483
03.606.009.1
230V
16 A
GST18
233
03.606.200.1
6
9
RM (technical description on page 240)
230V
16 A
Schuko CEE7/7
8
733
03.307.008.1
230V
16 A
Schuko CEE7/7
17
1183
03.307.017.1
230V
16 A
Schuko CEE7/7
9
633
03.607.009.1
230V
16 A
Schuko CEE7/7
18
933
03.607.018.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
24
1133
03.607.825.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
45
1833
03.607.845.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
18
6
1233
03.607.824.1
230/400V
3 x 16 A
IEC60309 3ph/N/PE 6h
36
6
1833
03.607.842.1
230V
32 A
IEC60309 1ph/N/PE 6h
24
1111
03.637.023.1
230V
32 A
IEC60309 1ph/N/PE 6h
12
4
871
03.637.016.1
230V
32 A
IEC60309 1ph/N/PE 6h
21
4
1168
03.637.025.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
6
563
03.637.006.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
6
12
995
03.637.018.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
21
1022
03.637.021.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
18
6
1157
03.637.024.1
230/400V
3 x 32 A
IEC60309 3ph/N/PE 6h
36
6
1751
03.637.042.1
Outputs:
C13
= IEC60320 C13
C19
= IEC60320 C19
Schuko = Protective contact plug DIN 49440
UTE
= France Standard CEE 7-V
Type 13 = Switzerland, type 13
F2
= Design side panel (for installing at workstation)
L
= Length in mm
19"
= Suitable for 19" installation
S
= Switch
safe
= Child-proof
F1
= Standard side pane (for rack mounting)
Rack PDUs | 245
DI-STRIP®
3-Phase in Rack with GST18
Features
Requirement
Constant energy increase requirements in the rack caused by high
packing densities (e.g. 1 U Pizza
servers, blade servers, etc.) (1)
Solution
3-phase distributor with GST18
plug system, e.g. 96 A with
redundant feed. (2)
1. DOS20147
2. DOS20132
3. DOS20142
4. DOS20135
Benefits (3, 4)
– Modularity.
– Plug-in capability (no wiring
required).
– Can be expanded.
– Cascadable.
– Easy implementation of
redundancies/UPS-secured circuits.
– Combination of DIN Schuko /
IEC320 Euro systems.
– Any installation position can be
selected.
– Good alternative to 3-phase
DI-STRIP Triple Power.
Power Supply Cable, 3-Phase
Accessories for GST 18 Plug System
– GST 18 socket for connecting GST18i5
distributor block with 3 phases.
– 5-pole (L1, L2, L3, N, PE) 250/400 V ~.
– Cable: H05VV-F 5G 2.5 mm2.
L
DOS20104
S
n
F1
F2
19"
Color
– Black.
Safe
Model
2000
Order No.
UP
04.000.048.0
1 unit
Order No.
UP
04.000.038.9
1 unit
GST18i5 Distributor Block, 3-Phase
–
–
–
–
DOS20103
246 | Rack PDUs
L
For individual connection at the customer.
Modular plug-in connection.
3-phase distribution on various socket strips.
Including mounting panel.
S
n
F1
F2
19"
Safe
Color
– Black.
Model
DI-STRIP®
Power Supply Cable, Single Phase
Accessories for GST 18 Plug System
– Mains plug CEE/VII: GST18 socket (Wieland).
– Cable: H05VV-F3G 1.5 mm2.
L
S
n
F1
F2
19"
Safe
Color
– White.
Order No.
UP
2000
Model
04.000.040.0
1 unit
5000
04.000.041.0
1 unit
DOS00467
Connection Cable
Accessories for GST 18 Plug System
– GST 18 plug.
– GST 18 socket.
– Cable: H05VV-F3G 1.5 mm2.
L
DOS00469
S
n
F1
F2
Color
– For color coding circuits (e.g. UPS).
Model
Order No.
UP
200
19"
Safe
White
04.000.042.0
1 unit
200
Black
04.000.042.9
1 unit
500
White
04.000.037.0
1 unit
500
Black
04.000.037.9
1 unit
1000
White
04.000.044.0
1 unit
1000
Black
04.000.044.9
1 unit
5000
White
04.000.045.0
1 unit
DOS20105
GST18 Socket
– With threaded connection for cross-section
1.5 – 2.5 mm2 with cable strain relief.
– For individual connection.
L
S
n
F1
F2
19"
Safe
Color
– White.
Model
Order No.
UP
04.000.046.0
1 unit
Order No.
UP
04.000.047.0
1 unit
DOS00471
GST18 Plug
– With threaded connection for cross-section
1.5 – 2.5 mm2 with cable strain relief.
– For individual, further cabling.
L
S
n
F1
F2
19"
Safe
Color
– White.
Model
DOS00470
Rack PDUs | 247
DI-STRIP®
Mains Cable for Euro Socket Strip
For DIN 49 440 and French/Belgian Standard
– Mains plug CEE/VII: Euro socket IEC 320.
– Cable: H05VV-F 3G 1 mm2.
Mains voltage
– 250 VAC.
Nominal current
– 10 A.
DOS00076
L
S
n
F1
F2
19"
Safe
Model
Order No.
UP
2000
04.000.054.9
1 unit
6000
04.000.053.9
1 unit
Mains Cable for Euro Socket Strip
For Swiss Standard
– Mains plug: Type 12 - Euro socket IEC 320.
– Cable: H05VV-F 3G 1 mm2.
Mains voltage
– 250 VAC.
Nominal current
– 10 A.
DOS00077
L
S
n
F1
F2
19"
Safe
Model
2000
Order No.
UP
04.000.055.9
1 unit
Mains Cable for Euro Socket Strip
For British Standard
– Mains plug: Type BS 1363 IEC320 Euro socket.
– Cable: H05VV-F 3G 1 mm2.
DOS00078
L
S
n
F1
F2
Mains voltage
– 250 VAC.
Nominal current
– 10 A.
19"
Safe
Model
2000
Order No.
UP
04.000.056.9
1 unit
UP
Euro Connection Cable
–
–
–
–
DOS00519
Mains plug: IEC 320.
Euro socket IEC 320.
Cable: H05VV-F 3G 1 mm2.
USA: SJT AWG18 with USA approval.
L
S
n
F1
F2
19"
Mains voltage
– 250 VAC.
Nominal current
– 10 A.
Model
Order No.
900
Safe
EU
04.000.051.9
1 unit
900
USA
04.000.052.9
1 unit
Dimensions in mm:
Conversion:
L = Length
n = Number of sockets
U
S = Switch
F1 = Standard side panel
UP = Packaging unit
F2 = Design side panel
= Standard rack unit
Safe = child-proof
19" = ideal for 19" components
Replace .x with the number of your color combination: .1 = RAL 7035, .6 = RAL 7035/RAL 2003
248 | Rack PDUs
1 mm = 0.03937 inch
1 kg = 2.2046 pounds
DI-STRIP®
SafetySleeve™ Cable Protection IEC C19
– SafetySleeves protect the feed lines of the
network equipment.
– Compatible with all C19 cables and fit onto
all PDUs.
DOS20493
L
W
H
U
Material / Finish
– PVC, black.
Model
Order No.
UP
C20 plug in C19 socket
03.910.212.9 001
20 unit
SafetySleeve™ Cable Protection IEC C13
– SafetySleeves protect the feed lines of the
network equipment.
– Compatible with all C13 cables and fit onto
all PDUs.
Material / Finish
– PVC, black.
DOS20494
L
W
H
U
Model
Order No.
UP
C14 plug in C13 socket
03.910.213.9 001
50 unit
Rack PDUs | 249
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement