Manitowoc | SD0692N | Specifications | Manitowoc SD0692N Specifications

Manitowoc SD0692N Specifications
S Model
Ice Machines
Installation
Use and Care
Manual
Thank you for selecting a Manitowoc Ice Machine, the dependability leader in ice making equipment and related
products. With proper installation, care and maintenance, your new Manitowoc Ice Machine will provide you with many
years of reliable and economical performance.
This manual is updated as new information and models
are released. Visit our website for the latest manual.
www.manitowocice.com
Part Number 000000345
03/2006
Safety Notices
Procedural Notices
As you work on an S Model Series Ice Machine, be sure
to pay close attention to the safety notices in this
manual. Disregarding the notices may lead to serious
injury and/or damage to the ice machine.
As you work on an S Model Series Ice Machine, be sure
to read the procedural notices in this manual. These
notices supply helpful information which may assist you
as you work.
Throughout this manual, you will see the following types
of safety notices:
Throughout this manual, you will see the following types
of procedural notices:
! Warning
PERSONAL INJURY POTENTIAL
Do not operate equipment that has been misused,
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
! Warning
Text in a Warning box alerts you to a potential
personal injury situation. Be sure to read the
Warning statement before proceeding, and work
carefully.
Important
Text in an Important box provides you with
information that may help you perform a procedure
more efficiently. Disregarding this information will
not cause damage or injury, but it may slow you
down as you work.
NOTE: Text set off as a Note provides you with simple,
but useful, extra information about the procedure you
are performing.
Read These Before Proceeding:
! Caution
! Caution
Text in a Caution box alerts you to a situation in
which you could damage the ice machine. Be sure
to read the Caution statement before proceeding,
and work carefully.
Proper installation, care and maintenance are
essential for maximum ice production and troublefree operation of your Manitowoc Ice Machine.
Read and understand this manual. It contains
valuable care and maintenance information. If you
encounter problems not covered by this manual, do
not proceed, contact Manitowoc Ice, Inc. We will be
happy to provide assistance.
Important
Routine adjustments and maintenance procedures
outlined in this manual are not covered by the
warranty.
Table of Contents
Section 1
General Information
Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Read a Model Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Cube Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bin Caster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Bagger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guardian Sachet Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Arctic Pure Water Filter System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manitowoc Cleaner and Sanitizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AuCS® Automatic Cleaning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model/Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Owner Warranty Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Labor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorized Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-3
1-4
1-4
1-4
1-4
1-4
1-4
1-4
1-4
Section 2
Installation Instructions
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S320/S420 Air and Water-Cooled Ice Machines . . . . . . . . . . . . . . . . . . . .
S600 Air and Water-Cooled Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . .
S600 Remote Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S300/S450/S500/S850/s1000/S1200 Air and Water-Cooled Ice Machines
S500/S850/S1000 Remote Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . . .
S1400 / S1600 / S1800 Air and Water-Cooled Ice Machines . . . . . . . . . . .
S1400 / S1600 / S1800 Remote Ice Machines . . . . . . . . . . . . . . . . . . . . . .
Ice Storage Bin Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 Inch (56 cm) Ice Storage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30 inch (76 cm) Ice Storage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48 Inch (130 cm) Ice Storage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Large Capacity Ice Storage Bin Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . .
30 Inch (76 cm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48 Inch (122 cm) & 60 Inch (152 cm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Condenser Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JC0495/JC0895/JC1395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location of Ice Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Heat of Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Drain Plug and Leveling the Ice Storage Bin . . . . . . . . . . . . . . . .
Air-Cooled Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum Circuit Ampacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Breaker Size & Minimum Circuit Amperage Chart . . . . . . . . . . .
Part Number 000000345
2-1
2-1
2-1
2-2
2-2
2-3
2-4
2-5
2-5
2-6
2-6
2-6
2-6
2-7
2-7
2-7
2-8
2-8
2-9
2-9
2-10
2-10
2-11
2-11
2-11
2-11
2-11
2-12
1
Table of Contents (continued)
Self-Contained Electrical Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . .
Self Contained Ice Machine 115/1/60 or 208-230/1/60 . . . . . . . . . . . . . . . .
Self Contained Ice Machine 208-230/3/60 . . . . . . . . . . . . . . . . . . . . . . . . . .
Self Contained Ice Machine 230/1/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For United Kingdom Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Electrical Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Ice Machine With Single Circuit Model Condenser
115/1/60 or 208-230/1/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Ice Machine With Single Circuit Model Condenser
208-230/3/60 or 380-415/3/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Ice Machine With Single Circuit Model Condenser
230/1/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Supply and Drain Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Inlet Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drain Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling Tower Applications (Water-Cooled Models) . . . . . . . . . . . . . . . . . . .
Water Supply and Drain Line Sizing/Connections . . . . . . . . . . . . . . . . . . . .
Remote Condenser/Line Set Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Ice Machines Refrigerant Charge . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guidelines for Routing Line Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calculating Remote Condenser Installation Distances . . . . . . . . . . . . . . . .
Lengthening or Reducing Line Set Lengths . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting A Line Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Receiver Service Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Ice Machine Usage with Non-Manitowoc Multi-Circuit Condensers
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Head Pressure Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Condenser Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condenser DT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refrigerant Charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Connect Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Manitowoc Multi-Circuit Condenser Sizing Chart . . . . . . . . . . . . . . . . .
Installation Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Checks for Remote Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Starting the Ice Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AuCS® Automatic Cleaning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-13
2-13
2-13
2-13
2-13
2-14
2-14
2-14
2-14
2-15
2-15
2-15
2-15
2-15
2-16
2-17
2-17
2-18
2-18
2-19
2-20
2-20
2-20
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-22
2-23
2-23
2-24
2-24
Section 3
Ice Machine Operation
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sequence Of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial Start-Up or Start-Up After Automatic Shut-Off . . . . . . . . . . . . . . . . . .
Freeze Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Harvest Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Shut-Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warm Water Rinse Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operational Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Thickness Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Harvest Sequence Water Purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3-1
3-2
3-2
3-2
3-3
3-3
3-3
3-3
3-4
3-4
3-4
3-4
3-5
Part Number 000000345
Table of Contents (continued)
Section 4
Maintenance
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water-Cooled Condenser and Water Regulating Valve . . . . . . . . . . . . . . . . .
AlphaSan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guardian . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guardian Sachet Replacement Frequency . . . . . . . . . . . . . . . . . . . . . . . . .
Sachet Installation/Replacement Procedure . . . . . . . . . . . . . . . . . . . . . . . .
Clean Up Procedure for Damaged Sachet Packet . . . . . . . . . . . . . . . . . . .
Interior Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sanitizing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal of Parts For Cleaning/Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Front Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal from Service/Winterization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Contained Air-Cooled Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . . .
Water-Cooled Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AuCS Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-1
4-1
4-1
4-2
4-2
4-3
4-3
4-3
4-3
4-4
4-4
4-4
4-5
4-6
4-12
4-13
4-13
4-13
4-13
4-13
4-13
Section 5
Before Calling For Service
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Limit Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part Number 000000345
5-1
5-2
3
Table of Contents (continued)
4
Part Number 000000345
Section 1
General Information
Section 1
General Information
Model Numbers
! Warning
This manual covers the following models:
Self-Contained
Air-Cooled
SD0302A
SY0304A
SD0322A
SY0324A
SR0420A
SD0422A
SY0424A
SD0452A
SY0454A
SR0500A
SD0502A
SY0504A
SD0602A
SY0604A
SR0850A
SD0852A
SY0854A
SD1002A
SY1004A
SD1202A
SY1204A
SD1402A
SY1404A
SR1600A
SD1602A
SY1604A
SR1800A
SD1802A
SY1804A
Self-Contained
Water-Cooled
SD0303W
SY0305W
SD0323W
SY0325W
SR0421W
SD0423W
SY0425W
SD0453W
SY0455W
SR0501W
SD0503W
SY0505W
SD0603W
SY0605W
SR0851W
SD0853W
SY0855W
SD1003W
SY1005W
SD1203W
SY1205W
SD1403W
SY1405W
SR1601W
SD1603W
SY1605W
SR1801W
SD1803W
SY1805W
PERSONAL INJURY POTENTIAL
Remote
------------------------SR0590N
SD0592N
SY0594N
SD0692N
SY0694N
SR0890N
SD0892N
SY0894N
SD1092N
SY1094N
----SD1492N
SY1494N
SR1690N
SD1692N
SY1694N
SR1890N
SD1892N
SY1894N
Do not operate equipment that has been misused,
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
! Warning
PERSONAL INJURY POTENTIAL
Remove all ice machine panels before lifting and
installing.
How to Read a Model Number
9 REMOTE
AIR-COOLED
# CUBE SIZE
CONDENSER TYPE
0
1
2
3
4
5
AIR-COOLED
WAT ER-COOLED
AIR-COOLED
WAT ER-COOLED
AIR-COOLED
WAT ER-COOLED
REGULAR
REGULAR
DICE
DICE
HALF-DICE
HALF-DICE
S Y 1094
ICE MACHINE
MODEL
ICE CUBE SIZE
R REGULAR
D DICE
Y HALF DICE
N
ICE MACHINE
SERIES
CONDENSER TYPE
A SELF-CONTAINED AIR-COOLED
W SELF-CONTAINED WAT ER-COOLED
N REMOTE AIR-COOLED
Ice Cube Sizes
NOTE: Model numbers ending in 3 indicate a 3-phase
unit. Example: SY1004A3
Regular
Dice
Half Dice
1-1/8" x 1-1/8" x 7/8"
7/8" x 7/8" x 7/8"
3/8" x 1-1/8" x 7/8"
2.86 x 2.86 x 2.22 cm 2.22 x 2.22 x 2.22 cm 0.95 x 2.86 x 2.22 cm
Part Number 000000345
1-1
General Information
Section 1
Accessories
MANITOWOC CLEANER AND SANITIZER
Contact your Manitowoc distributor for these optional
accessories:
Manitowoc Ice Machine Cleaner and Sanitizer are
available in convenient 16 oz. (473 ml) bottles. These
are the only cleaner and sanitizer approved for use with
Manitowoc products.
BIN CASTER
Replaces standard legs.
ICE BAGGER
Maximize profits from bagged ice sales with this
convenient accessory. This sturdy unit rests on the bin
door frame, and adapts for left or right side filling.
GUARDIANf SACHET PACKETS
Guardian sachet packets release chlorine dioxide on a
controlled basis to inhibit the growth of bacteria and
slime.
Guardian sachet packets are available through your
local Manitowoc Ice Machine dealer.
ARCTIC PUREf WATER FILTER SYSTEM
Engineered specifically for Manitowoc ice machines,
This water filter is an efficient, dependable, and
affordable method of inhibiting scale formation, filtering
sediment, and removing chlorine taste and odor.
Cleaner Part Number
16 ounce Bottle - 94-0546-3
AuCS®-SO - 94-0546-3
AuCS®-SI - 40-1326-3
Sanitizer Part Number
16 ounce Bottle - 94-0565-3
AuCS®-SO - 94-0565-3
AuCS®-SI - 40-1327-3
AUCS® AUTOMATIC CLEANING SYSTEM
This accessory reduces equipment cleaning expense.
The AuCS® accessory monitors ice making cycles and
initiates cleaning procedures automatically.
DISPENSER
A counter-top dispenser is ideal for cafeterias and many
types of self-service facilities. Manitowoc auto-fill, floorstanding ice dispensers meet the strict sanitary
requirements of the food service, lodging and health
care industries.
! Warning
All Manitowoc ice machines require the ice storage
system (bin, dispenser, etc.) to incorporate an ice
deflector.
48” wide S Model ice machines require adding
Manitowoc Ice Deflector Kit K00349 when installing
with non-Manitowoc ice storage systems.
30” wide S Model ice machines require adding
Manitowoc Ice Deflector Kit K00347 when installing
with non-Manitowoc ice storage systems.
Prior to using a non-Manitowoc ice storage system
with other Manitowoc ice machines, contact the
manufacturer to assure their ice deflector is
compatible with Manitowoc ice machines.
1-2
Part Number 000000345
Section 1
General Information
Model/Serial Number Location
These numbers are required when requesting
information from your local Manitowoc distributor, or
Manitowoc Ice, Inc.
The model and serial number are listed on the MODEL/
SERIAL NUMBER DECAL affixed to the ice machine,
remote condenser and storage bin.
SV13147
MODEL/SERIAL DECAL
LOCATION
Model/Serial Number Location
Part Number 000000345
1-3
General Information
Section 1
Owner Warranty Registration Card
GENERAL
EXCLUSIONS
The packet containing this manual also includes
warranty information. Warranty coverage begins the day
your new ice machine is installed.
The following items are not included in the ice machine’s
warranty coverage:
Important
Complete and mail the OWNER WARRANTY
REGISTARATION CARD as soon as possible to
validate the installation date.
If you do not return your OWNER WARRANTY
REGISTRATION CARD, Manitowoc will use the date of
sale to the Manitowoc Distributor as the first day of
warranty coverage for your new ice machine.
Warranty Coverage
GENERAL
1. Normal maintenance, adjustments and cleaning.
2. Repairs due to unauthorized modifications to the
ice machine or use of non-standard parts without
prior written approval from Manitowoc Ice, Inc.
3. Damage caused by improper installation of the ice
machine, electrical supply, water supply or drainage,
or damage caused by floods, storms, or other acts of
God.
4. Premium labor rates due to holidays, overtime,
etc.; travel time; flat rate service call charges;
mileage and miscellaneous tools and material
charges not listed on the payment schedule.
Additional labor charges resulting from the
inaccessibility of equipment are also excluded.
The following Warranty outline is provided for your
convenience. For a detailed explanation, read the
warranty bond shipped with each product.
5. Parts or assemblies subjected to misuse, abuse,
neglect or accidents.
Contact your local Manitowoc Distributor, Manitowoc Ice,
Inc. or visit our website at www.manitowocice.com if you
need further warranty information.
6. Damage or problems caused by installation,
cleaning and/or maintenance procedures
inconsistent with the technical instructions
provided in this manual.
Important
This product is intended exclusively for commercial
application. No warranty is extended for personal,
family, or household purposes.
PARTS
1. Manitowoc warrants the ice machine against defects
in materials and workmanship, under normal use
and service for three (3) years from the date of
original installation.
2. The evaporator and compressor are covered by an
additional two (2) year (five years total) warranty
beginning on the date of the original installation.
LABOR
1. Labor required to repair or replace defective
components is covered for three (3) years from the
date of original installation.
2. The evaporator is covered by an additional two (2)
year (five years total) labor warranty beginning on
the date of the original installation.
1-4
7. This product is intended exclusively for
commercial application. No warranty is extended
for personal, family, or household purposes.
AUTHORIZED WARRANTY SERVICE
To comply with the provisions of the warranty, a
refrigeration service company qualified and
authorized by a Manitowoc distributor, or a
Contracted Service Representative must perform the
warranty repair.
NOTE: If the dealer you purchased the ice machine from
is not authorized to perform warranty service, contact
your Manitowoc distributor or Manitowoc Ice, Inc. for the
name of the nearest authorized service representative.
Service Calls
Normal maintenance, adjustments and cleaning as
outlined in this manual are not covered by the
warranty. If you have followed the procedures listed on
page 5-1 of this manual, and the ice machine still does
not perform properly, call your authorized service
company.
Part Number 000000345
Section 2
Installation Instructions
Section 2
Installation Instructions
General
These instructions are provided to assist the qualified
installer. Check your local Yellow Pages for the name of
the nearest Manitowoc distributor, or call Manitowoc Ice,
Inc. for information regarding start-up services.
Important
Failure to follow these installation guidelines may
affect warranty coverage.
Ice Machine Dimensions
S320/S420 AIR AND WATER-COOLED ICE MACHINES
ELECTRICAL
AUCS
ELECTRICAL
2.20" (5.58cm)
5.0" (12.7cm)
H
19.3"
(49.0 cm)
3.25" (8.3cm)
4" (10cm)
2.6"
1.8"
(6.6cm)(4.6cm)
AUCS
TUBING &
MODULAR
WIRE
4.21" (10.69cm)
5.06" (12.85cm)
2.85" (7.30cm)
1.1" (2.6cm)
6.68" (16.96cm)
D
8.49" (21.56cm)
17.0" (43.2cm)
W
Ice Machine
S320
S420
Part Number 000000345
CONDENSER WATER
OUTLET 1/2"FPT
(Water-Cooled Only)
Dimension W
22 in. (55.9 cm)
22 in. (55.9 cm)
AUXILLARY BASE DRAIN
1/2"CPVC SOCKET
WATER INLET
CONDENSER WATER
3/8"FPT
INLET 3/8"FPT
(Water-Cooled Only)
DRAIN 1/2"NPTF
Dimension D
24.5 in. (62.2 cm)
24.5 in. (62.2 cm)
Dimension H
21.5 in (54.6 cm)
21.5 in (54.6 cm)
2-1
Installation Instructions
Section 2
S600 AIR AND WATER-COOLED ICE MACHINES
H
1.50" (3.81cm)
ELECTRICAL
8.50" (21.60cm)
A
AUCS
CONNECTIONS
6.50" (16.5cm)
B
CONDENSER WATER
OUTLET 1/2"FPT
(Water-Cooled Only)
2.61"
(6.62cm)
5.06" (12.85cm)
1.81"
6.68" (16.96cm)
(4.59cm)
2.85" (7.30cm)
D
AUXILLARY BASE DRAIN
1/2"CPVC SOCKET
CONDENSER WATER
INLET 3/8"FPT
(Water-Cooled Only)
DRAIN 1/2"NPTF
7.75" (19.7 cm)
WATER INLET
3/8"FPT
4.25" (10.81 cm)
17.25" (43.81 cm)
W
Ice Machine
S600
Dimension A
11.5 in (29.2 cm)
Dimension B
9.0 in (22.9 cm)
Dimension W
30 in. (76.2 cm)
Dimension D
24.50 in. (62.2 cm)
Dimension H
21.5 in (54.6 cm)
S600 REMOTE ICE MACHINES
H
ELECTRICAL
1.50" (3.81cm)
A
B
REMOTE CONDENSER
ELECTRICAL
1.81"
(4.59cm)
2.61"
(6.62cm)
6.25" (15.88cm)
D
5.06" (12.85cm)
AUXILLARY BASE
DRAIN 1/2"CPVC
SOCKET
6.68" (16.96cm)
11.50" (29.21cm)
WATER INLET
3/8"FPT
16.0" (40.64cm)
DRAIN 1/2"NPTF
W
Ice Machine
S600
2-2
Dimension A
11.5 in (29.2 cm)
Dimension B
9.0 in (22.9 cm)
Dimension W
30 in. (76.2 cm)
REFRIGERANT
LIQUID LINE
REFRIGERANT
DISCHARGE LINE
Dimension D
24.50 in. (62.2 cm)
Dimension H
21.5 in (54.6 cm)
Part Number 000000345
Section 2
Installation Instructions
S300/S450/S500/S850/S1000/S1200 AIR AND WATER-COOLED ICE MACHINES
ELECTRICAL
2.20" (5.58cm)
H
A
B
C
E
AUCS
CONNECTIONS
1.81"
(4.59cm)
2.61"
(6.62cm)
F
4.21" (10.69cm)
2.85" (7.30cm)
5.06" (12.85cm)
1.06 (2.7cm)
6.68" (16.96cm)
CONDENSER WATER
OUTLET 1/2"FPT
(Water-Cooled Only)
D
AUXILLARY BASE
DRAIN 1/2"CPVC
SOCKET
8.49" (21.56cm)
25.52" (64.82cm)
SV3143
CONDENSER WATER
INLET 3/8"FPT
(Water-Cooled Only)
WATER INLET
3/8"FPT
W
SV3143B
DRAIN 1/2"NPTF
Width, Depth, and Height Dimensions
Ice Machine
S300
S450
S500
S850
S1000
S1200
Dimension W
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
Dimension D
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
Dimension H
16.5 in (41.9 cm)
21.5 in (54.6 cm)
21.5 in (54.6 cm)
26.5 in (67.3 cm)
26.5 in (67.3 cm)
29.5 in (74.9cm)
Electrical and AuCS Dimensions
Ice Machine
S300
S450
S500
S850
S1000
S1200
Electrical
Dimension A
Dimension B
14.00 in (35.6 cm)
NA
19.25 in (48.9 cm)
17.5 in (44.45 cm)
19.25 in (48.9 cm)
17.5 in (44.45 cm)
23.82 in (60.5 cm) 22.32 in (56.69 cm)
23.82 in (60.5 cm) 22.32 in (56.69 cm)
27.0 in (68.6 cm)
25.25 in (54.1 cm)
Part Number 000000345
Dimension C
10.0 in (25.4 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
AuCS
Dimension E
6.0 in (15.24 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
8.5 in (21.6 cm)
Dimension F
4.0 in (10.16 cm)
6.5 in (16.5 cm)
6.5 in (16.5 cm)
6.5 in (16.5 cm)
6.5 in (16.5 cm)
6.5 in (16.5 cm)
2-3
Installation Instructions
Section 2
S500/S850/S1000 REMOTE ICE MACHINES
ELECTRICAL
REMOTE CONDENSER
ELECTRICAL
2.20" (5.58cm)
A
H
B
1.81"
(4.59cm)
2.61"
(6.62cm)
1.06 (2.69cm)
6.12" (15.54cm)
D
5.06" (12.85cm)
6.68" (16.96cm)
12.26" (42.27cm)
WATER INLET
3/8"FPT
16.64" (64.82cm)
DRAIN 1/2"NPTF
SV3146
Ice Machine
S300
S450
S500
S850
S1000
2-4
W
Dimension A
14.00 in (35.6 cm)
19.25 in (48.9 cm)
19.25 in (48.9 cm)
23.82 in (60.5 cm)
23.82 in (60.5 cm)
Dimension B
NA
17.5 in (44.45 cm)
17.5 in (44.45 cm)
22.32 in (56.69 cm)
22.32 in (56.69 cm)
Dimension W
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
30 in. (76.2 cm)
REFRIGERANT
LIQUID LINE
REFRIGERANT
DISCHARGE LINE
Dimension D
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
24.50 in. (62.2 cm)
SV3146B
Dimension H
16.5 in (41.9 cm)
21.5 in (54.6 cm)
21.5 in (54.6 cm)
26.5 in (67.3 cm)
26.5 in (67.3 cm)
Part Number 000000345
Section 2
Installation Instructions
S1400 / S1600 / S1800 AIR AND WATER-COOLED ICE MACHINES
2.50" (6.35cm)
ELECTRICAL
H
A
B
C
11.0" (27.9cm)
AuCS
Connections
E
2.0" (5.1cm)
F
WATER INLET
3/8"FPT
5.75" (14.6cm)
CONDENSER WATER
OUTLET 1/2"FPT
(Water-Cooled Only)
1.1" (2.8cm)
4.0"
7.8" (19.8cm)
(10.2cm)
10.25" (26.0cm)
CONDENSER WATER
INLET 1/2"FPT
(Water-Cooled Only)
D
3.0" (7.6cm)
11.0" (27.9cm)
3.75" (9.5cm)
AUXILLARY BASE DRAIN
1/2"CPVC SOCKET
W
DRAIN 1/2"NPTF
Width, Depth, and Height Dimensions
Ice Machine
S1400
S1600
S1800
Dimension W
48 in. (121.9 cm)
48 in. (121.9 cm)
48 in. (121.9 cm)
Dimension D
24.5 in. (62.2 cm)
24.5 in. (62.2 cm)
24.5 in. (62.2 cm)
Dimension H
29.5 in (74.9 cm)
29.5 in (74.9 cm)
29.5 in (74.9 cm)
Electrical and AuCS Dimensions
Electrical
Dimension A
Dimension B
22.75 in (57.8 cm)
22.25 in (56.5 cm)
22.75 in (57.8 cm)
22.25 in (56.5 cm)
22.75 in (57.8 cm)
22.25 in (56.5 cm)
Ice Machine
S1400
S1600
S1800
AuCS
Dimension E
9.5 in (24.1 cm)
9.5 in (24.1 cm)
9.5 in (24.1 cm)
Dimension C
14.0 in (35.6 cm)
14.0 in (35.6 cm)
14.0 in (35.6 cm)
Dimension F
7.5 in (19.1 cm)
7.5 in (19.1 cm)
7.5 in (19.1 cm)
S1400 / S1600 / S1800 REMOTE ICE MACHINES
2.50" (6.35cm)
ELECTRICAL
H
A
B
C
11.0" (27.9cm)
8.0"
(20.3cm)
AuCS
Connections
WATER INLET
3/8"FPT
E
2.0" (5.1cm)
F
CONDENSER WATER
INLET 1/2"FPT
(Water-Cooled Only)
5.75" (14.6cm)
1.1" (2.8cm)
4.0"
7.8" (19.8cm)
(10.2cm)
10.25" (26.0cm)
CONDENSER WATER
OUTLET 1/2"FPT
(Water-Cooled Only)
D
3.0" (7.6cm)
11.0" (27.9cm)
AUXILLARY BASE DRAIN
1/2"CPVC SOCKET
3.75" (9.5cm)
REFRIGERANT
LIQUID LINE
DRAIN 1/2"NPTF
23.75" (60.3cm)
28.25" (71.8cm)
REFRIGERANT
DISCHARGE LINE
W
Ice Machine
S1400
S1600
S1800
Dimension A
22.75 in (57.8 cm)
22.75 in (57.8 cm)
22.75 in (57.8 cm)
Part Number 000000345
Dimension B
22.25 in (56.5 cm)
22.25 in (56.5 cm)
22.25 in (56.5 cm)
Dimension W
48 in. (121.9 cm)
48 in. (121.9 cm)
48 in. (121.9 cm)
Dimension D
24.5 in. (62.2 cm)
24.5 in. (62.2 cm)
24.5 in. (62.2 cm)
Dimension H
29.5 in (74.9 cm)
29.5 in (74.9 cm)
29.5 in (74.9 cm)
2-5
Installation Instructions
Section 2
Ice Storage Bin Dimensions
22 INCH (56 CM) ICE STORAGE BINS
48 INCH (130 CM) ICE STORAGE BINS
SV1614
SV1297
Bin Model
B320
B420
Dimension A
34.0 in (86.3 cm)
34.0 in (86.3 cm)
Dimension B
32.0 in (81.3 cm)
44.0 in (111.7 cm)
30 INCH (76 CM) ICE STORAGE BINS
B970
SV1609
Bin Model
B170
B400
B570
2-6
Dimension A
29.5 in (74.9 cm)
34.0 in (86.3 cm)
34.0 in (86.3 cm)
Dimension B
19.1 in (48.5 cm)
32.0 in (81.3 cm)
44.0 in (111.7 cm)
Part Number 000000345
Section 2
Installation Instructions
Large Capacity Ice Storage Bin Dimensions
30 INCH (76 CM)
! Warning
A
34” (86.4 cm)
B
All Manitowoc ice machines require the ice storage
system (bin, dispenser, etc.) to incorporate an ice
deflector.
The S600, S850, S1000 ice machines require adding
Manitowoc Ice Deflector Kit K00347 when installing
with non-Manitowoc ice storage systems.
Prior to using a non-Manitowoc ice storage system
with other Manitowoc ice machines, contact the
manufacturer to assure their ice deflector is
compatible with Manitowoc ice machines.
25.25”
(64.1 cm)
! Caution
30” large capacity ice storage bins must be
attached to the wall with the bracket provided with
the bin.
43.6”
(110.81 cm)
6”
(15.2 cm)
Bin Model
Dimension A (Width)
B750
30 in. (76.2 cm.)
B1050
30 in. (76.2 cm.)
The bin drain is exactly in the center of the bin.
Dimension B (Height)
58 in. (147.3 cm.)
78 in. (198.1 cm.)
48 INCH (122 CM) & 60 INCH (152 CM)
A
34” (86.4 cm)
B
25.25”
(64.1 cm)
43.6”
(110.81 cm)
6”
(15.2 cm)
Bin Model
Dimension A (Width)
B1100
48 in. (121.9 cm.)
B1400
60 in. (152.4 cm.)
The bin drain is exactly in the center of the bin.
Part Number 000000345
Dimension B (Height)
55.0 in. (139.7 cm.)
55.0 in. (139.7 cm.)
2-7
Installation Instructions
Section 2
Remote Condenser Dimensions
JC0495/JC0895/JC1395
SV1297
2-8
Part Number 000000345
Section 2
Installation Instructions
Location of Ice Machine
Ice Machine Heat of Rejection
The location selected for the ice machine must meet the
following criteria. If any of these criteria are not met,
select another location.
•
The location must be free of airborne and other
contaminants.
•
The air temperature must be at least 35°F (1.6°C),
but must not exceed 110°F (43.4°C).
•
Remote air cooled - The air temperature must be at
least -20°F (-29°C), but must not exceed 120°F
(49°C)
•
The location must not be near heat-generating
equipment or in direct sunlight and must be protected
from weather.
•
The location must not obstruct air flow through or
around the ice machine. Refer to the chart below for
clearance requirements.
S300/S320/S450/S500/
S600/S850/S1000
Top/Sides
Back
S420
Top/Sides
Back
S1200
Top
Sides
Back
S1400/S1600/S1800
Top/Sides
Back
Series
Ice Machine
S300
S320
S420
S450
S500
S600
S850
S1000
S1200
S1400
S1600
S1800
Heat of Rejection
Air Conditioning
Peak
3800
6000
3800
6000
7000
9600
7000
9600
7000
9600
9000
13900
12000
18000
16000
22000
19000
28000
19000
28000
21000
31000
24000
36000
B.T.U./Hour
Because the heat of rejection varies during the ice making cycle,
the figure shown is an average.
Self-Contained
Air-Cooled
8" (20.3 cm)
5" (12.7 cm)
Water-Cooled
and Remote*
8" (20.3 cm)
5" (12.7 cm)
Ice machines, like other refrigeration equipment, reject
heat through the condenser. It is helpful to know the
amount of heat rejected by the ice machine when sizing
air conditioning equipment where self-contained aircooled ice machines are installed.
Self-Contained
Air-Cooled
12" (30.5 cm)
5" (12.7 cm)
Water-Cooled
and Remote*
8" (20.3 cm)
5" (12.7 cm)
This information is also necessary when evaluating the
benefits of using water-cooled or remote condensers to
reduce air conditioning loads. The amount of heat added
to an air conditioned environment by an ice machine
using a water-cooled or remote condenser is negligible.
Self-Contained
Air-Cooled
8" (20.3 cm)
12" (30.5 cm)
5" (12.7 cm)
Water-Cooled
and Remote*
8" (20.3 cm)
8" (20.3 cm)
5" (12.7 cm)
Self-Contained
Air-Cooled
24" (61.0 cm)
12" (30.5 cm)
Water-Cooled
and Remote*
8" (20.3 cm)
5" (12.7 cm)
Knowing the amount of heat rejected is also important
when sizing a cooling tower for a water-cooled
condenser. Use the peak figure for sizing the cooling
tower.
*There is no minimum clearance required for water-cooled or remote
ice machines. This value is recommended for efficient operation and
servicing only.
! Caution
The ice machine must be protected if it will be
subjected to temperatures below 32°F (0°C).
Failure caused by exposure to freezing
temperatures is not covered by the warranty. See
“Removal from Service/Winterization”.
Part Number 000000345
2-9
Installation Instructions
Section 2
Removing Drain Plug and Leveling the Ice
Storage Bin
1. Remove threaded plug from drain fitting.
2. Screw the leveling legs onto the bottom of the bin.
3. Screw the foot of each leg in as far as possible.
! Caution
The legs must be screwed in tightly to prevent them
from bending.
Air-Cooled Baffle
SELF-CONTAINED AIR-COOLED ONLY
The air-cooled baffle prevents condenser air from
recirculating. To install:
1. Remove the back panel screws next to the
condenser.
2. Align the mounting holes in the air baffle with the
screw holes and reinstall the screws.
4. Move the bin into its final position.
5. Level the bin to assure that the bin door closes and
seals properly. Use a level on top of the bin. Turn the
base of each foot as necessary to level the bin.
6. Inspect bin gasket prior to ice machine installation.
(Manitowoc bins come with a closed cell foam
gasket installed along the top surface of the bin.)
AIR
BAFFLE
7. Remove all panels from ice machine before lifting.
Remove both front panels, top cover, left and right
side panels.
SCREWS
8. Install ice machine on bin.
THREAD LEVELING
LEG INTO BASE OF
CABINET
SV1607
Air Baffle
SV1606
Leveling Leg and Foot
2-10
Part Number 000000345
Section 2
Installation Instructions
Electrical Service
Important
GENERAL
Observe correct polarity of incoming line voltage.
! Warning
All wiring must conform to local, state and national
codes.
Incorrect polarity can lead to erratic ice machine
operation and a safety issue. This is especially critical on
230 volt / 50 cycle ice machines.
Fuse/Circuit Breaker
VOLTAGE
The maximum allowable voltage variation is ±10% of the
rated voltage at ice machine start-up (when the electrical
load is highest).
A separate fuse/circuit breaker must be provided for
each ice machine. Circuit breakers must be H.A.C.R.
rated (does not apply in Canada).
MINIMUM CIRCUIT AMPACITY
! Warning
The ice machine must be grounded in accordance
with national and local electrical codes.
All electrical work, including wire routing and grounding,
must conform to local, state and national electrical
codes. The following precautions must be observed:
•
The ice machine must be grounded.
•
A separate fuse/circuit breaker must be provided for
each ice machine.
•
A qualified electrician must determine proper wire
size dependent upon location, materials used and
length of run (minimum circuit ampacity can be used
to help select the wire size).
•
The maximum allowable voltage variation is +/-10 of
the rated voltage at ice machine start-up (when the
electrical load is highest).
•
Check all green ground screws in the control box and
verify they are tight before starting the ice machine.
Part Number 000000345
The minimum circuit ampacity is used to help select the
wire size of the electrical supply. (Minimum circuit
ampacity is not the ice machine’s running amp load.)
The wire size (or gauge) is also dependent upon
location, materials used, length of run, etc., so it must be
determined by a qualified electrician.
ELECTRICAL REQUIREMENTS
Refer to Ice Machine Model/Serial Plate for voltage/
amperage specifications.
GROUND FAULT CIRCUIT INTERUPTER
Ground Fault Circuit Interupter (GFCI/GFI) protection is
a system that shuts down the electric circuit (opens it)
when it senses an unexpected loss of power,
presumably to ground. Manitowoc Ice, Inc. does not
recommend the use of a GFCI/GFI circuit protection with
our equipment. If code requires the use of a GFCI/GFI
then you must follow the local code. The circuit must be
dedicated, sized properly and there must be a panel
GFCI/GFI breaker. We do not recommend GFCI/GFI
outlets as they are known for more intermittent nuisance
trips than panel breakers.
2-11
Installation Instructions
Section 2
MAXIMUM BREAKER SIZE & MINIMUM CIRCUIT AMPERAGE CHART
(* indicates preliminary data)
Ice Machine
S300
S320
S420/S450
S500
S600
S850
S1000
S1200
S1400
S1600
S1800
Voltage
Phase
Cycle
115/1/60
230/1/50
115/1/60
208-230/1/60
230/1/50
115/1/60
208-230/1/60
230/1/50
115/1/60
208-230/1/60
230/1/50
208-230/1/60
230/1/50
208-230/1/60
208-230/3/60
230/1/50
208-230/1/60
208-230/3/60
230/1/50
208-230/1/60
208-230/3/60
230/1/50
208-230/1/60
208-230/3/60
230/1/50
208-230/1/60
208-230/3/60
230/1/50
208-230/1/60
208-230/3/60
230/1/50
Air-Cooled
Maximum
Minimum
Fuse/Circuit
Circuit Amps
Breaker
20
12.9
15
6.4
15
11.3
15
6.0
15
6.0
20
16.3
15
8.2
15
6.7
20
13.0
15
7.3
15
6.5
15
8.3
15
6.7
20
11.3
15
7.8
20
10.5
20
13.6
15
9.9
20
12.6
30
17.1
20
11.4
30
13.7
30
17.5
20
13.2
30
15.1
30
19.8
20
13.5
30
16.7
40
23.5
20
13.4
40
21.9
Water Cooled
Maximum
Minimum
Fuse/Circuit
Circuit Amps
Breaker
20
12.1
15
5.9
15
10.5
15
5.6
15
5.6
20
15.6
15
8.2
15
6.4
20
12.3
15
6.9
15
5.9
15
7.9
15
6.1
20
10.3
15
6.8
20
9.1
20
12.6
15
8.9
20
11.2
30
16.1
20
10.4
30
12.3
30
16.1
20
11.8
30
13.7
30
18.4
20
12.1
30
15.3
40
22.1
20
12.0
40
20.5
Remote
Maximum
Minimum
Fuse/Circuit
Circuit Amps
Breaker
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
20
14.1
N/A
N/A
N/A
N/A
15
8.9
15
7.1
20
10.6
15
7.8
20
9.7
20
12.8
15
9.9
20
12.0
N/A
N/A
N/A
N/A
N/A
N/A
30
17.1
20
12.8
30
14.7
30
19.4
20
13.1
30
13.1
40
23.1
20
13.0
40
21.5
MINIMUM POWER CORD SPECIFICATIONS
Maximum Breaker Size
15 amp
20 amp
30 amp
40 amp
Minimum Wire Size
14 gauge
12 gauge
10 gauge
8 gauge
Maximum Length of Power Cord
6 feet (1.83 m)
6 feet (1.83 m)
6 feet (1.83 m)
6 feet 1(.83 m)
If a power cord is used the wire size to the receptacle is dependant upon location, materials used, length of run, etc.,
so it must be determined by a qualified electrician. Local, state or national requirements will supersede our minimum
requirements.
2-12
Part Number 000000345
Section 2
Installation Instructions
Self-Contained Electrical Wiring Connections
! Warning
These diagrams are not intended to show proper
wire routing, wire sizing, disconnects, etc., only the
correct wire connections.
SELF CONTAINED ICE MACHINE
208-230/3/60
All electrical work, including wire routing and
grounding, must conform to local, state and national
electrical codes.
Though wire nuts are shown in the drawings, the ice
machine field wiring connections may use either
wire nuts or screw terminals.
SELF CONTAINED ICE MACHINE
115/1/60 OR 208-230/1/60
L1
L1
L2
L2
L3
L3
GROUND
ICE MACHINE
CONNECTIONS
SV1190
L1
L1
N=115V
OR
L2=208-230V
GROUND
SV1258
GROUND
TO SEPARATE
FUSE/BREAKER
ICE MACHINE
CONNECTIONS
SELF CONTAINED ICE MACHINE
230/1/50
L1
GROUND
L1
TO SEPARATE
FUSE/BREAKER
N
N
GROUND
GROUND
ICE MACHINE
CONNECTIONS
SV1191
TO SEPARATE
FUSE/BREAKER.
DISCONNECT ALL
POLES.
For United Kingdom Only
As the colors of the wires in the mains lead of the appliance may not correspond with the colored markings
identifying the terminals in your plug, proceed as follows:
•
The wire which is colored green and yellow must be connected to the terminal in the plug which is marked with
the letter E or by the earth ground symbol
or colored green or green and yellow.
•
The wire colored blue must be connected to the terminal which is marked with the letter N or colored black.
•
The wire colored brown must be connected to the terminal which is marked with the letter L or colored red.
Part Number 000000345
2-13
Installation Instructions
Section 2
Remote Electrical Wiring Connections
REMOTE ICE MACHINE
WITH SINGLE CIRCUIT MODEL CONDENSER
208-230/3/60 OR 380-415/3/50
! Warning
These diagrams are not intended to show proper
wire routing, wire sizing, disconnects, etc., only the
correct wire connections.
SINGLE
CIRCUIT
REMOTE
CONDENSER
L1
NOTE: FAN
MOTOR IS
208-230V
L2
All electrical work, including wire routing and
grounding, must conform to local, state and national
electrical codes.
GROUND
Though wire nuts are shown in the drawings, the ice
machine field wiring connections may use either
wire nuts or screw terminals.
F2
F1
Important
F2 wire is located in the compressor compartment
behind the control box. The wire is labeled F2 and
capped with a wire nut.
ICE
MACHINE
L1
L1
L2
L2
L3
L3
REMOTE ICE MACHINE
WITH SINGLE CIRCUIT MODEL CONDENSER
115/1/60 OR 208-230/1/60
GROUND
GROUND
TO SEPARATE
FUSE/BREAKER
SV1199
L1
SINGLE
CIRCUIT
L2
REMOTE
CONDENSER
GROUND
NOTE:
CONDENSER FAN
MOTOR VOLTAGE
MATCHES ICE
MACHINE
VOLTAGE (115V
OR 208-230V)
REMOTE ICE MACHINE
WITH SINGLE CIRCUIT MODEL CONDENSER
230/1/50
L
SINGLE CIRCUIT 1
REMOTE
CONDENSER
L2
F2
NOTE: FAN
MOTOR IS
220-240V
F1
ICE
MACHINE
L1
L1
N=115V OR L2=208-230V
L2
GROUND
SV1255
L2
F2
GROUND
TO SEPARATE
FUSE/BREAKER
ICE
MACHINE
F1
L1
L1
N
N
GROUND
SV1256
2-14
GROUND
TO SEPARATE
FUSE/BREAKER
(220-240).
DISCONNECT ALL
POLES.
Part Number 000000345
Section 2
Installation Instructions
Water Supply and Drain Requirements
DRAIN CONNECTIONS
WATER SUPPLY
Follow these guidelines when installing drain lines to
prevent drain water from flowing back into the ice
machine and storage bin:
Local water conditions may require treatment of the
water to inhibit scale formation, filter sediment, and
remove chlorine odor and taste.
Important
If you are installing a Manitowoc Arctic Puref water
filter system, refer to the Installation Instructions
supplied with the filter system for ice making water
inlet connections.
•
Drain lines must have a 1.5 inch drop per 5 feet of
run (2.5 cm per meter), and must not create traps.
•
The floor drain must be large enough to
accommodate drainage from all drains.
•
Run separate bin and ice machine drain lines.
Insulate them to prevent condensation.
•
Vent the bin and ice machine drain to the
atmosphere. Do not vent the condenser drain on
water-cooled models.
WATER INLET LINES
Follow these guidelines to install water inlet lines:
•
•
Do not connect the ice machine to a hot water
supply. Be sure all hot water restrictors installed for
other equipment are working. (Check valves on sink
faucets, dishwashers, etc.)
If water pressure exceeds the maximum
recommended pressure (80 psi), obtain a water
pressure regulator from your Manitowoc distributor.
Cooling Tower Applications
(Water-Cooled Models)
A water cooling tower installation does not require
modification of the ice machine. The water regulator
valve for the condenser continues to control the
refrigeration discharge pressure.
•
Install a water shut-off valve for both the ice making
and condenser water lines.
It is necessary to know the amount of heat rejection, and
the pressure drop through the condenser and water
valves (inlet and outlet) when using a cooling tower on
an ice machine.
•
Insulate water inlet lines to prevent condensation.
•
Water entering the condenser must not exceed 90°F
(32.2°C).
•
Water flow through the condenser must not exceed 5
gallons (19 liters) per minute.
•
Allow for a pressure drop of 7 psi (48 kPA) between
the condenser water inlet and the outlet of the ice
machine.
•
Water exiting the condenser must not exceed 110°F
(43.3°C).
! Caution
Do not apply heat to water valve inlet fitting. This will
damage plastic water inlet connection.
IMPORTANT
The Commonwealth of Massachusetts requires that all
water-cooled models must be connected only to a closed
loop, cooling tower system.
Part Number 000000345
2-15
Installation Instructions
Section 2
WATER SUPPLY AND DRAIN LINE SIZING/CONNECTIONS
! Caution
Plumbing must conform to state and local codes.
Location
Water Temperature
Water Pressure
Ice Machine Fitting
Ice Making
Water Inlet
35°F (1.6°C) Min.
90°F (32.2°C) Max.
20 psi (137.9 kPA) Min.
80 psi (551.5 kPA) Max.
3/8" Female Pipe
Thread
Tubing Size Up to Ice
Machine Fitting
3/8" (.95 cm) minimum
inside diameter
Ice Making
Water Drain
---
---
1/2" Female
Pipe Thread
1/2" (1.27 cm) minimum
inside diameter
Condenser
Water Inlet
40°F (4.4°C) Min.
90°F (32.2°C) Max.
20 psi (137.9 kPA) Min.
150 psi (1034.2 kPA) Max.
Condenser
Water Drain
---
---
Bin Drain
---
---
Large Capacity
Bin Drain
---
---
3/8" Female Pipe Thread
1/2" Female
Pipe Thread
3/4" Female
Pipe Thread
1” Female Pipe Thread
1/2" (1.27 cm) minimum
inside diameter
3/4" (1.91 cm) minimum
inside diameter
1” (25.4 mm) min. inside
diameter
Refer to “Ice Machine Dimensions” at the beginning of Section 2 for the exact locations of inlets and drains for the model you are working on.
3/8” FPT ICE MAKING WATER INLET FITTING,
PLASTIC FITTING ON OPPOSITE SIDE DO NOT
APPLY HEAT
ELECTRICAL ENTRANCE
18” (46 CM) VENT TUBE
3/8” FPT CONDENSER WATER INLET
(WATER COOLED UNITS ONLY
1/2” DRAIN CONNECTION
PLASTIC FITTING ON OPPOSITE
SIDE DO NOT APPLY HEAT
1/2” FPT CONDENSER WATER DRAIN
(WATER COOLED UNITS ONLY)
1/2” (1.3 CM) MIN
DRAIN ID
1/2” CPVC SOCKET AUXILLARY BASE
DRAIN
AIR GAP
DO NOT TRAP DRAIN LINE,
LEAVE AIR GAP BETWEEN
DRAIN TUBE AND DRAIN
OPEN, TRAPPED AND
VENTED DRAIN
SV3142
Typical Water Supply Drain Installation
2-16
Part Number 000000345
Section 2
Installation Instructions
Remote Condenser/Line Set Installation
Ice Machine
Remote Single
Circuit
Condenser
S500
JC0495
S600/S800/S1000
JC0895
S1400/S1600/
S1800
*Line Set
RT
RL
JC1395
Discharge Line
1/2" (1.27 cm)
1/2" (1.27 cm)
Line Set*
RT-20-R404A
RT-35-R404A
RT-50-R404A
RT-20-R404A
RT-35-R404A
RT-50-R404A
RL-20-R404A
RL-35-R404A
RL-50-R404A
Liquid Line
5/16" (.79 cm)
3/8" (.95 cm)
IMPORTANT
EPA CERTIFIED TECHNICIANS
If remote line set length is between 50' and 100' (15.2530.5 m), add additional refrigerant to the nameplate charge.
Refer to the Installation Instructions in Installation Use and
Care Manual for the model being worked on.
Tubing length: ______________________________
Refrigerant added to nameplate: ________________
New total refrigerant charge: ___________________
Typical Additional Refrigerant Label
! Warning
Potential Personal Injury Situation
The ice machine contains refrigerant charge.
Installation of the line sets must be performed by a
properly trained and EPA certified refrigeration
technician aware of the dangers of dealing with
refrigerant charged equipment.
Air Temperature Around the Condenser
Minimum
Maximum
-20°F (-29°C)
120°F (49°C)
! Caution
Never add more than nameplate charge to the
refrigeration system for any application.
REMOTE ICE MACHINES
REFRIGERANT CHARGE
Each remote ice machine ships from the factory with a
refrigerant charge appropriate for installation with line
sets of up to 50' (15.25 m). The serial tag on the ice
machine indicates the refrigerant charge.
Additional refrigerant may be required for installations
using line sets between 50' and 100’ (15.25-30.5 m)
long. If additional refrigerant is required, refer to the
chart below for the correct amount to be added.
Ice Machine
S500
S600
S850
S1000
S1400
S1600
S1800
Part Number 000000345
Nameplate Charge
(Charge Shipped in Ice Machine)
6 lb. (96 oz.)
6.5 lb.(104 oz)
8.5 lb. (136 oz.)
8.5 lb. (136 oz.)
11 lb. (176 oz.)
11.5 lb (184 oz.)
12.5 lb. (200 oz.)
Refrigerant to be Added for
50'-100' Line Sets
1.5 lb. (24 oz.)
1.5 lb. (24 oz.)
2 lb. (32 oz.)
2 lb. (32 oz.)
2 lb. (32 oz.)
2 lb. (32 oz.)
1 lb. (16 oz.)
Maximum System Charge
(Never Exceed)
7.5 lb. (120 oz.)
8 lb. (128 oz.)
10.5 lb. (168 oz.)
10.5 lb. (168 oz.)
13 lb. (208 oz.)
13.5 lb. (216 oz.)
13.5 lb. (216 oz.)
2-17
Installation Instructions
Section 2
GENERAL
GUIDELINES FOR ROUTING LINE SETS
Condensers must be mounted horizontally with the fan
motor on top.
First, cut a 2.5" (6.35 cm) circular hole in the wall or roof
for tubing routing. The line set end with the 90° bend will
connect to the ice machine. The straight end will connect
to the remote condenser.
Remote condenser installations consist of vertical and
horizontal line sets between the ice machine and the
condenser. When combined, they must fit within
approved specifications. The following guidelines,
drawings and calculation methods must be followed to
verify a proper remote condenser installation.
! Caution
The 60 month compressor warranty (including the
36 month labor replacement warranty) will not apply
if the remote ice machine is not installed according
to specifications.
This warranty also will not apply if the refrigeration
system is modified with a condenser, heat reclaim
device, or other parts or assemblies not
manufactured by Manitowoc Ice, Inc., unless
specifically approved in writing by Manitowoc Ice,
Inc.
Follow these guidelines when routing the refrigerant
lines. This will help insure proper performance and
service accessibility.
1. Optional - Make the service loop in the line sets (as
shown below). This permits easy access to the ice
machine for cleaning and service. Do not use hard
rigid copper at this location.
2. Required - Do not form traps in the refrigeration lines
(except the service loop). Refrigerant oil must be
free to drain toward the ice machine or the
condenser. Route excess tubing in a supported
downward horizontal spiral (as shown below). Do
not coil tubing vertically.
3. Required - Keep outdoor refrigerant line runs as
short as possible.
3
DOWNWARD
HORIZONTAL
SPIRAL
2
2
3
1
1
SV1204
Routing Line Sets
2-18
Part Number 000000345
Section 2
Installation Instructions
Make the following calculations to make sure the line set
layout is within specifications.
CALCULATING REMOTE CONDENSER
INSTALLATION DISTANCES
Line Set Length
1. Insert the measured rise into the formula below.
Multiply by 1.7 to get the calculated rise.
(Example: A condenser located 10 feet above the
ice machine has a calculated rise of 17 feet.)
The maximum length is 100' (30.5 m).
The ice machine compressor must have the proper oil
return. The receiver is designed to hold a charge
sufficient to operate the ice machine in ambient
temperatures between -20°F (-29°C) and 120°F (49°C),
with line set lengths of up to 100' (30.5 m).
2. Insert the measured drop into the formula below.
Multiply by 6.6 to get the calculated drop.
(Example. A condenser located 10 feet below the
ice machine has a calculated drop of 66 feet.)
Line Set Rise/Drop
3. Insert the measured horizontal distance into the
formula below. No calculation is necessary.
The maximum rise is 35' (10.7 m).
The maximum drop is 15' (4.5 m).
4. Add together the calculated rise, calculated drop,
and horizontal distance to get the total calculated
distance. If this total exceeds 150' (45.7 m), move
the condenser to a new location and perform the
calculations again.
! Caution
If a line set has a rise followed by a drop, another
rise cannot be made. Likewise, if a line set has a
drop followed by a rise, another drop cannot be
made.
Calculated Line Set Distance
The maximum calculated distance is 150' (45.7 m).
Line set rises, drops, horizontal runs (or combinations of
these) in excess of the stated maximums will exceed
compressor start-up and design limits. This will cause
poor oil return to the compressor.
Maximum Line Set Distance Formula
Step 1.
Step 2.
Step 3.
Step 4.
Measured Rise (35' [10.7 m] Maximum)
______ x 1.7
Measured Drop (15' [4.5 m] Maximum)
______ x 6.6
Measured Horizontal Distance (100' [30.5 m] Maximum)
Total Calculated Distance 150' (45.7 m)
=
=
_______
_______
_______
_______
H
H
H
R
D
D
R
SV1196
Combination of a Rise and a
Horizontal Run
Part Number 000000345
Calculated Rise
Calculated Drop
Horizontal Distance
Total Calculated Distance
SV1195
Combination of a Drop and a
Horizontal Run
SV1194
Combination of a Rise, a Drop
and a Horizontal Run
2-19
Installation Instructions
Section 2
LENGTHENING OR REDUCING LINE SET LENGTHS
REMOTE RECEIVER SERVICE VALVE
In most cases, by routing the line set properly,
shortening will not be necessary. When shortening or
lengthening is required, do so before connecting the line
set to the ice machine or the remote condenser. This
prevents the loss of refrigerant in the ice machine or
condenser.
The receiver service valve is closed during shipment.
Open the valve prior to starting the ice machine.
The quick connect fittings on the line sets are equipped
with Schraeder valves. Use these valves to recover any
vapor charge from the line set. When lengthening or
shortening lines follow good refrigeration practices,
purge with nitrogen and insulate all tubing. Do not
change the tube sizes. Evacuate the lines and place
about 5 oz (143g) of vapor refrigerant charge in each
line.
1. Remove the top and left side panels.
2. Remove the receiver service valve cap.
3. Backseat (open) the valve.
4. Reinstall the cap and panels.
REMOVE FRONT, TOP,
AND LEFT SIDE PANEL
FOR ACCESS TO
RECEIVER VALVE
CONNECTING A LINE SET
TURN
COUNTERCLOCKWISE
TO OPEN
1. Remove the dust caps from the line set, condenser
and ice machine.
2. Apply refrigeration oil to the threads on the quick
disconnect couplers before connecting them to the
condenser.
3. Carefully thread the female fitting to the condenser
or ice machine by hand.
4. Tighten the couplings with a wrench until they
bottom out.
5. Turn an additional 1/4 turn to ensure proper brassto-brass seating. Torque to the following
specifications:
Liquid Line
10-12 ft lb.
(13.5-16.2 N•m)
Discharge Line
35-45 ft lb.
(47.5-61.0 N•m)
SV1603
RECEIVER SERVICE
VALVE CAP (TURN
COUNTERCLOCKWISE
TO REMOVE)
Backseating the Receiver Service Valve
6. Check all fittings and valve caps for leaks.
7. Make sure Schraeder cores are seated and
Schraeder caps are on and tight.
2-20
Part Number 000000345
Section 2
Installation Instructions
Remote Ice Machine Usage with Non-Manitowoc Multi-Circuit Condensers
WARRANTY
FAN MOTOR
The sixty (60) month compressor warranty, including
thirty six (36) month labor replacement warranty, shall
not apply when the remote ice machine is not installed
within the remote specifications. The foregoing warranty
shall not apply to any ice machine installed and/or
maintained inconsistent with the technical instructions
provided by Manitowoc Ice, Inc. Performance may vary
from Sales specifications. S-Model ARI certified
standard ratings only apply when used with a Manitowoc
remote condenser.
The condenser fan must be on during the complete ice
machine freeze cycle (do not cycle on fan cycle control).
The ice maker has a condenser fan motor circuit for use
with a Manitowoc condenser. It is recommended that this
circuit be used to control the condenser fan(s) on the
multi-circuit condenser to assure it is on at the proper
time. Do not exceed the rated amps for the fan motor
circuit listed on the ice machine’s serial tag.
If the design of the condenser meets the specifications,
Manitowoc’s only approval is for full warranty coverage
to be extended to the Manitowoc manufactured part of
the system. Since Manitowoc does not test the
condenser in conjunction with the ice machine,
Manitowoc will not endorse, recommend, or approve the
condenser, and will not be responsible for its
performance or reliability.
Important
Manitowoc warrants only complete new and unused
remote packages. Guaranteeing the integrity of a
new ice machine under the terms of our warranty
prohibits the use of pre-existing (used) tubing or
condensers.
HEAD PRESSURE CONTROL VALVE
Any remote condenser connected to a Manitowoc SModel Ice Machine must have a head pressure control
valve #836809-3 (available from Manitowoc Distributors)
installed on the condenser package. Manitowoc will not
accept substitute “off the shelf” head pressure control
valves.
INTERNAL CONDENSER VOLUME
The multi-circuit condenser internal volume must not be
less than or exceed that used by Manitowoc (see chart
on next page). Do not exceed internal volume and try
to add charge to compensate, as compressor failure
will result.
CONDENSER ∆T
∆T is the difference in temperature between the
condensing refrigerant and entering air. The ∆T should
be 15 to 20°F (-9.4 to -6.6°C) at the beginning of the
freeze cycle (peak load conditions) and drop down to 12
to 17°F (-11.1 to -8.3°C) during the last 75% of the
freeze cycle (average load conditions).
REFRIGERANT CHARGE
Remote ice machines have the serial plate refrigerant
charge (total system charge) located in the ice maker
section. (Remote condensers and line sets are supplied
with only a vapor charge.)
! Caution
Never add more than nameplate charge to ice
machine for any application.
QUICK CONNECT FITTINGS
! Caution
Do not use a fan cycling control to try to maintain
discharge pressure. Compressor failure will result.
Part Number 000000345
The ice machine and line sets come with quick connect
fittings. It is recommended that matching quick connects
(available through Manitowoc Distributors) be installed in
the multi-circuit condenser, and that a vapor “holding”
charge (5 oz.) of proper refrigerant be added to the
condenser prior to connection of the ice machine or line
set to the condenser.
2-21
Installation Instructions
Section 2
NON-MANITOWOC MULTI-CIRCUIT CONDENSER SIZING CHART
Ice
Machine
Model
Refrigerant
Type
Charge
Heat of Rejection
Average
Btu/hr
Peak
Btu/hr
Internal
Condenser
Volume (cu ft)
Min
Design
Pressure
Max
S500
R-404A
6 lbs.
7,000
9,600
0.020
0.035
S600
S850
S1000
S1400
S1600
R404A
R-404A
R-404A
R-404A
R-404A
6.5 lbs.
8.5 lbs.
8.5 lbs.
11 lbs.
11.5 lbs
9,000
12,000
16,000
19,000
21,000
13,900
18,000
22,000
28,000
31,000
0.045
0.045
0.045
0.085
0.085
0.060
0.060
0.060
0.105
0.105
S1800
R-404A
12.5 lbs.
24,000
36,000
0.085
0.105
500 psig
(3447 kpa)
(34.47 bar)
safe working
pressure
2,500 psig
(17237 kpa)
(172.37 bar)
burst
pressure
Quick Connect StubsMale Ends
Discharge
Liquid
Head
Pressure
Control
Valve
coupling
P/N
83-6035-3
coupling
P/N
83-6034-3
Manitowoc
P/N
83-6809-3
mounting
flange P/N
83-6006-3
mounting
flange P/N
83-6005-3
no
substitutes
SINGLE CIRCUIT REMOTE
CONDENSER
ELECTRICAL
DISCONNECT
DISCHARGE
LINE
LIQUID LINE
TO CIRCUIT
BREAKER
PANEL
ELECTRICAL
DISCONNECT
ICE MACHINE
ELECTRICAL
SUPPLY
36.00"
(91.44 cm)
DROP
BIN
DISCHARGE
REFRIGERANT
LINE
LIQUID
REFRIGERANT
LINE
SV1615
Typical Single Circuit Remote Condenser Installation
2-22
Part Number 000000345
Section 2
Installation Instructions
Installation Check List
F
F
F
F
F
F
F
F
F
F
Is the Ice Machine level?
Has all of the internal packing been
removed?
Have all of the electrical and water
connections been made?
F
F
F
Has the supply voltage been tested and
checked against the rating on the nameplate?
F
Is there proper clearance around the ice
machine for air circulation?
F
Is the ice machine grounded and polarity
correct?
Has the ice machine been installed where
ambient temperatures will remain in the
range of 35° - 110°F (1.6° - 43.3°C)?
Has the ice machine been installed where the
incoming water temperature will remain in the
range of 35° - 90°F (1.6° - 32.2°C)?
F
F
Are all electrical leads free from contact with
refrigeration lines and moving equipment?
Has the owner/operator been instructed
regarding maintenance and the use of
Manitowoc Cleaner and Sanitizer?
Has the owner/operator completed the
warranty registration card?
Has the ice machine and bin been sanitized?
Is the toggle switch set to ice? (The toggle
switch is located directly behind the front
panel).
Is the ice thickness control set correctly?
(Refer to Operational Checks to check/set
the correct ice bridge thickness).
Additional Checks for Remote Models
F
Is there a separate drain for the water-cooled
condenser?
F
Is there a separate drain for the bin?
F
F
F
Part Number 000000345
Are the ice machine and bin drains vented?
Has the receiver service valve been
opened?
Does the remote condenser fan operate
properly after start-up?
Has the remote condenser been located
where ambient temperatures will remain in
the range of -20° - 120°F ( -29 - 49°C).
Is the line set routed properly?
Are both refrigeration lines to remote
condenser run so they do not lay in water
and are properly insulated?
2-23
Installation Instructions
Section 2
Before Starting the Ice Machine
AuCS® Automatic Cleaning System
All Manitowoc ice machines are factory-operated and
adjusted before shipment. Normally, new installations do
not require any adjustment.
This optional accessory monitors ice making cycles and
initiates cleaning procedures automatically. The AuCS®
accessory can be set to automatically clean or sanitize
the ice machine every 2, 4 or 12 weeks. Refer to the
AuCS® Installation, Use and Care Manual for details.
To ensure proper operation, follow the Operational
Checks in Section 3 of this manual. Starting the ice
machine and completing the Operational Checks are the
responsibilities of the owner/operator.
Adjustments and maintenance procedures outlined in
this manual are not covered by the warranty.
! Warning
Potential Personal Injury Situation
Do not operate equipment that has been misused.
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
2-24
Part Number 000000345
Section 3
Ice Machine Operation
Section 3
Ice Machine Operation
Component Identification
Water Distribution Tube
Toggle Switch
Water Curtain
Dump Valve
Check Valve
sv3149
Ice Thickness Probe
Bin Switch
Water Level Probe
Water Pump
Water Inlet Location
Water Inlet Valve
(Located in Refrigeration Compartment)
sv3150
Part Number 000000345
3-1
Ice Machine Operation
Section 3
Sequence Of Operation
NOTE: The toggle switch must be in the ice position and
the water curtain must be in place on the evaporator
before the ice machine will start.
INITIAL START-UP OR START-UP AFTER
AUTOMATIC SHUT-OFF
1. Water Purge
Before the compressor starts, the water pump and water
dump solenoid are energized for 45 seconds, to
completely purge the ice machine of old water. This
feature ensures that the ice making cycle starts with
fresh water.
The harvest valve(s) is also energized during water
purge, although it stays on for an additional 5 seconds
(50 seconds total on time) during the initial refrigeration
system start-up.
When Used - The air compressor energizes for the last
10 seconds of the cycle.
2. Refrigeration System Start-Up
The compressor starts after the 45 second water purge,
and it remains on throughout the entire Freeze and
Harvest Sequences. The water fill valve is energized at
the same time as the compressor. The harvest valve(s)
remains on for 5 seconds during initial compressor startup and then shuts off.
FREEZE SEQUENCE
3. Prechill
The compressor is on for 30 seconds (60 seconds initial
cycle) prior to water flow, to prechill the evaporator. The
water fill valve remains on until the water level probe is
satisfied.
4. Freeze
The water pump restarts after the prechill. An even flow
of water is directed across the evaporator and into each
cube cell, where it freezes. The water fill valve will cycle
on and then off one more time to refill the water trough.
When sufficient ice has formed, the water flow (not the
ice) contacts the ice thickness probe. After
approximately 10 seconds of continual water contact,
the harvest sequence is initiated. The ice machine
cannot initiate a harvest sequence until a 6 minute
freeze lock has been surpassed.
NOTE: Freeze lock is bypassed after moving the toggle
switch from OFF to ICE position for the first cycle only.
At the same time the compressor starts, the condenser
fan motor (air-cooled models) is supplied with power
throughout the entire Freeze and Harvest Sequences.
The fan motor is wired through a fan cycle pressure
control, therefore it may cycle on and off. (The
compressor and condenser fan motor are wired through
the contactor. As a result, anytime the contactor coil is
energized, the compressor and fan motor are supplied
with power.)
3-2
Part Number 000000345
Section 3
Ice Machine Operation
HARVEST SEQUENCE
SAFETY TIMERS
5. Water Purge
The control board has the following non-adjustable
safety timers:
The harvest valve(s) opens at the beginning of the water
purge to divert hot refrigerant gas into the evaporator.
The water pump continues to run, and the water dump
valve energizes for 45 seconds to purge the water in the
sump trough. The water fill valve energizes (turns on)
and de-energizes (turns off) strictly by time. The water fill
valve energizes for the last 15 seconds of the 45-second
water purge.
After the 45 second water purge, the water fill valve,
water pump and dump valve de-energize. (Refer to
“Water Purge Adjustment” for details.)
•
The ice machine is locked into the freeze cycle for 6
minutes before a harvest cycle can be initiated.
Freeze lock is bypassed after moving the toggle
switch from OFF to ICE position for the first cycle
only.
•
The maximum freeze time is 60 minutes at which
time the control board automatically initiates a
harvest sequence (steps 5 & 6).
•
The maximum harvest time is 3.5 minutes at which
time the control board automatically initiates a freeze
sequence (steps 3 & 4).
6. Harvest
The harvest valve(s) remains open and the refrigerant
gas warms the evaporator causing the cubes to slide, as
a sheet, off the evaporator and into the storage bin. The
sliding sheet of cubes swings the water curtain out,
opening the bin switch.
The momentary opening and re-closing of the bin switch
terminates the harvest sequence and returns the ice
machine to the freeze sequence (Step 3 - 4.)
When Used - The air compressor energizes after 35
seconds and remains energized throughout the entire
harvest cycle. The air compressor will automatically
energize for 60 seconds when the harvest cycle time
exceeded 75 seconds in the previous cycle.
AUTOMATIC SHUT-OFF
WARM WATER RINSE CYCLE
Closing the back of the evaporator allows ice to build up
on the rear of the evaporator and the plastic evaporator
frame parts. After 200 freeze/harvest cycles have been
complete the control board will initiate a warm water
rinse.
After the 200th harvest cycle ends:
•
The Clean and Harvest LED’s energize to indicate
the ice machine is in a warm water rinse.
•
The compressor and harvest valve remain
energized.
•
The water pump energizes.
•
The water inlet valve energizes until water contacts
the water level probe.
•
The compressor and harvest valve warm the water
for 5 minutes, then de-energize.
•
The water pump remains energized for an additional
5 minutes (10 minute total on time) then deenergizes.
7. Automatic Shut-Off
When the storage bin is full at the end of a harvest
sequence, the sheet of cubes fails to clear the water
curtain and will hold it open. After the water curtain is
held open for 30 seconds, the ice machine shuts off. The
ice machine remains off for 3 minutes before it can
automatically restart.
The ice machine remains off until enough ice has been
removed from the storage bin to allow the ice to fall clear
of the water curtain. As the water curtain swings back to
the operating position, the bin switch re-closes and the
ice machine restarts (steps 1 - 2), provided the 3 minute
delay period is complete.
Part Number 000000345
NOTE: The warm water rinse cycle can be terminated by
moving the toggle switch to the OFF position, then back to ICE.
3-3
Ice Machine Operation
Section 3
Operational Checks
ICE THICKNESS CHECK
GENERAL
The ice thickness probe is factory-set to maintain the ice
bridge thickness at 1/8" (.32 cm).
Manitowoc ice machines are factory-operated and
adjusted before shipment. Normally, new installations do
not require any adjustment.
To ensure proper operation, always follow the
Operational Checks:
•
when starting the ice machine for the first time
•
after a prolonged out of service period
•
after cleaning and sanitizing
NOTE: Routine adjustments and maintenance
procedures are not covered by the warranty.
WATER LEVEL
The water level sensor is set to maintain the proper
water level above the water pump housing. The water
level is not adjustable. If the water level is incorrect,
check the water level probe for damage (probe bent,
etc.). Clean the water level probe with ice machine
cleaner, rinse thoroughly and re-check operation. Repair
or replace the probe as necessary.
NOTE: Make sure the water curtain is in place when
performing this check. It prevents water from splashing
out of the water trough.
1. Inspect the bridge connecting the cubes. It should
be about 1/8" (.32 cm) thick.
2. If adjustment is necessary, turn the ice thickness
probe adjustment screw clockwise to increase
bridge thickness, counterclockwise to decrease
bridge thickness. Set at 1/4” gap between ice
machine and evaporator as starting point, then
adjust to achieve a 1/8” bridge thickness.
NOTE: Turning the adjustment 1/3 of a turn will change
the ice thickness about 1/16" (1.5 mm).
ADJUSTING SCREW
1/8” ICE BRIDGE THICKNESS
SV3132
Ice Thickness Check
3. Make sure the ice thickness probe wire and the
bracket do not restrict movement of the probe.
Water Level Probe Location
3-4
Part Number 000000345
Section 3
Ice Machine Operation
HARVEST SEQUENCE WATER PURGE
The harvest sequence water purge adjustment may be
used when the ice machine is hooked up to special
water systems, such as a de-ionized water treatment
system.
! Warning
•
During the harvest sequence water purge, the water
fill valve energizes and de-energizes by time. The
water purge must be at the factory setting of 45
seconds for the water fill valve to energize during the
last 15 seconds of the water purge. If it is set to less
than 45 seconds, the water fill valve will not energize
during the water purge.
Disconnect electric power to the ice machine at the
electrical disconnect before proceeding.
Important
The harvest sequence water purge is factory-set at
45 seconds. A shorter purge setting (with standard
water supplies such as city water) is not
recommended. This can increase water system
cleaning and sanitizing requirements.
•
The harvest sequence water purge is factory set for
45 seconds. Repositioning the jumper will set the
harvest water purge to 0 seconds. This setting does
not affect the SeCs or AuCs (cleaning) sequences.
45 second
setting
0 second
setting
SV3139
SV3140
Water Purge Adjustment
For your safety and to eliminate errors, we recommend
that a qualified service technician make the harvest
water purge adjustment.
Part Number 000000345
3-5
Ice Machine Operation
Section 3
THIS PAGE INTENTIONALLY LEFT BLANK
3-6
Part Number 000000345
Section 4
Maintenance
Section 4
Maintenance
General
Cleaning the Condenser
You are responsible for maintaining the ice machine in
accordance with the instructions in this manual.
Maintenance procedures are not covered by the
warranty.
GENERAL
! Warning
If you do not understand the procedures or the
safety precautions that must be followed, call your
local Manitowoc service representative to perform
the maintenance procedures for you.
We recommend that you perform the following
maintenance procedures a minimum of once every six
months to ensure reliable, trouble-free operation and
maximum ice production.
Ice Machine Inspection
! Warning
Disconnect electric power to the ice machine and
the remote condensing unit at the electric service
switch before cleaning the condenser.
Check all water fittings and lines for leaks. Also, make
sure the refrigeration tubing is not rubbing or vibrating
against other tubing, panels, etc.
Do not put anything (boxes, etc.) on the sides or back of
the ice machine. There must be adequate airflow
through and around the ice machine to maximize ice
production and ensure long component life.
Exterior Cleaning
Clean the area around the ice machine as often as
necessary to maintain cleanliness and efficient
operation. Use cleaners designed for use with stainless
steel products.
! Warning
Disconnect electric power to the ice machine head
section and the remote condensing unit at the
electric service switches before cleaning the
condenser.
A dirty condenser restricts airflow, resulting in
excessively high operating temperatures. This reduces
ice production and shortens component life. Clean the
condenser at least every six months. Follow the steps
below.
! Warning
The condenser fins are sharp. Use care when
cleaning them.
1. The washable aluminum filter on self-contained ice
machines is designed to catch dust dirt lint and
grease. Clean the filter with a mild soap and water.
2. Clean the outside of the condenser with a soft brush
or a vacuum with a brush attachment. Be careful not
to bend the condenser fins.
3. Shine a flashlight through the condenser to check
for dirt between the fins. If dirt remains:
A. Blow compressed air through the condenser fins
from the inside. Be careful not to bend the fan
blades.
B. Use a commercial condenser coil cleaner.
Follow the directions and cautions supplied with
the cleaner.
Continued on Next Page...
Sponge any dust and dirt off the outside of the ice
machine with mild soap and water. Wipe dry with a
clean, soft cloth.
Heavy stains should be removed with stainless steel
wool. Never use plain steel wool or abrasive pads. They
will scratch the panels.
Part Number 000000345
4-1
Maintenance
Section 4
4. Straighten any bent condenser fins with a fin comb.
“COMB” DOWN
ONLY
Water-Cooled Condenser
and Water Regulating Valve
Symptoms of restrictions in the condenser water circuit
include:
•
Low ice production
•
High water consumption
•
High operating temperatures
•
High operating pressures
CONDENSER
If the ice machine is experiencing any of these symptoms,
the water-cooled condenser and water regulating valve
may require cleaning due to scale build-up.
FIN
COMBS
Because the cleaning procedures require special pumps
and cleaning solutions, qualified maintenance or service
personnel must perform them.
AlphaSan®
SV1515
Straighten Bent Condenser Fins
5. Carefully wipe off the fan blades and motor with a
soft cloth. Do not bend the fan blades. If the fan
blades are excessively dirty, wash with warm, soapy
water and rinse thoroughly.
! Caution
If you are cleaning the condenser fan blades with
water, cover the fan motor to prevent water damage
and disconnect electrical power.
4-2
The goal of AlphaSan® is to keep the plastic surfaces of
an ice machine cleaner, by reducing or delaying the
formation of bio-film. The active ingredient in
AlphaSan® is the element silver in the form of silver ions
(Ag+). AlphaSan® slowly releases silver ions via an ion
exchange mechanism. When AlphaSan® is
compounded directly into a plastic part, a controlled
release of silver ions from the surface is regulated to
maintain an effective concentration at or near the
surface of the plastic ice machine part. AlphaSan’s®
unique ability to effectively control the release of silver
not only protects against undesired discoloration of the
plastic, but also will last the life of the plastic part.
Although AlphaSan® helps prevent bio-film build up it
does not eliminate the need for periodic cleaning and
maintenance. AlphaSan® has no adverse effect on the
taste of the ice or beverage.
Part Number 000000345
Section 4
Maintenance
Guardianf
Slime is a leading cause of ice machine breakdowns and
biological growth is a health concern. The Guardianf
system releases chlorine dioxide on a controlled basis to
inhibit the growth of bacteria and fungi that form slime
and cause malodors in the food zone of ice machines.
SACHET INSTALLATION/REPLACEMENT
PROCEDURE
1. Loosen the left screw and open the left front door.
The right front panel does not need to be removed.
The Guardianf will not control mineral or other water
borne buildup. Your water quality will determine the
length of time before mineral buildup affects ice machine
performance. Mineral buildup must be removed as often
as necessary to ensure trouble-free operation of the ice
machine.
The Guardianf sachet holder is included with the sachet
packets. Refer to installation/replacement procedure to
install/change sachet holder/ packet.
Inside Left
Front Door
Loosen
Screw
Screw Location
Guardian
2. Inside the front panel there are two thumbscrew
holes covered by stickers, pierce the sticker with a
screwdriver.
3. Attach the sachet holder to the front panel by
inserting the thumbscrews through the holes in the
sachet holder and tighten the thumbscrews.
Guardianf Location
GUARDIANf SACHET REPLACEMENT FREQUENCY
Sachet packet(s) require replacement every thirty (30)
days or whenever they come in direct contact with water.
Refer to chart below for requirements.
Ice Machine
S300/S320/S420/S450/S500/S600
S850/S1000/S1200/S1400/S1600/S1800
Sachet Use
1
1 or 2*
*Although one sachet is recommended, extreme conditions may
necessitate using two sachet packets.
Guardianf sachet packets are available through your
local Manitowoc ice machine dealer.
4. Remove the new sachet packet from foil package
and install into holder. Removing the foil package
allows moisture in the air to activate the sachet
contents.
5. Close the left front door and tighten the screw.
6. Discard the used sachet packet in the trash.
CLEAN UP PROCEDURE FOR DAMAGED SACHET
PACKET
1. Remove all ice from bin/dispenser and discard.
2. Initiate a cleaning and sanitizing sequence on the
ice machine (see next pages).
3. Clean the bin/dispenser. Flush the drain thoroughly
to prevent future drain blockage.
4. Sanitize the bin/dispenser.
5. Install a replacement sachet packet and reinstall all
panels.
Part Number 000000345
4-3
Maintenance
Section 4
Interior Cleaning and Sanitizing
! Caution
GENERAL
Clean and sanitize the ice machine every six months for
efficient operation. If the ice machine requires more
frequent cleaning and sanitizing, consult a qualified
service company to test the water quality and
recommend appropriate water treatment. An extremely
dirty ice machine must be taken apart for cleaning and
sanitizing.
! Caution
Use only Manitowoc approved Ice Machine Cleaner
(part number 94-0546-3) and Sanitizer (part number
94-0565-3). It is a violation of Federal law to use
these solutions in a manner inconsistent with their
labeling. Read and understand all labels printed on
bottles before use.
CLEANING PROCEDURE
! Caution
Do not mix Cleaner and Sanitizer solutions together.
It is a violation of Federal law to use these solutions
in a manner inconsistent with their labeling.
! Warning
Wear rubber gloves and safety goggles (and/or face
shield) when handling ice machine Cleaner or
Sanitizer.
Never use anything to force ice from the evaporator.
Damage may result.
Step 3 Remove all ice from the bin.
Step 4 To start cleaning, place the toggle switch in the
CLEAN position. The water will flow through the water
dump valve and down the drain. The Clean light will turn
on to indicate the ice machine is in the Cleaning mode.
Step 5 Wait about two minutes or until water starts to
flow over the evaporator.
Step 6 Add the proper amount of Manitowoc Ice
Machine Cleaner to the water trough by pouring
between water curtain and evaporator.
Model
Amount of Cleaner
S300/S320/S420
3 ounces (88 ml)
S450/S500/S600/S850/S1000/S1200 5 ounces (148 ml)
S1400/S1600/S1800
9 ounces (266 ml)
Step 7 The ice machine will automatically time out a
ten minute cleaning cycle, followed by six rinse cycles,
and stop. The Clean light will turn off to indicate the
Cleaning cycle is completed. This entire cycle lasts
approximately 30 minutes.
Step 8 When the cleaning process stops, move the
toggle switch to OFF position. Refer to “Sanitizing
Procedure” on the next page.
Step 9
Ice machine cleaner is used to remove lime scale or
other mineral deposits. It is not used to remove algae or
slime. Refer to the section on Sanitizing for removal of
algae and slime.
Step 1 Remove top cover. This will allow easiest
access for pouring cleaner.
Step 2 Set the toggle switch to the OFF position after
ice falls from the evaporator at the end of a Harvest
cycle. Or, set the switch to the OFF position and allow
the ice to melt off the evaporator.
A. The ice machine may be set to start and finish a
self-cleaning procedure then automatically start
ice making again.
B. You must wait about one minute into the
cleaning cycle (until water starts to flow over the
evaporator) then move the switch from CLEAN
to ICE position.
C. When the self-cleaning cycle is completed, an
ice making sequence will start automatically.
Important
After the toggle switch is moved to the ICE position,
opening the curtain switch will interrupt the cleaning
sequence. The sequence will resume from the point
of interruption when the curtain switch closes.
4-4
Part Number 000000345
Section 4
Maintenance
SANITIZING PROCEDURE
Use sanitizer to remove algae or slime. Do not use it to
remove lime scale or other mineral deposits.
Step 1 Set the toggle switch to the OFF position after
ice falls from the evaporator at the end of a Harvest
cycle. Or, set the switch to the OFF position and allow
the ice to melt off the evaporator.
Step 5 Use the sanitizing solution and a sponge or
cloth to sanitize (wipe) all parts and interior surfaces of
the ice machine. Sanitize the following areas:
A. Side walls
B. Base (area above water trough)
C. Evaporator plastic parts
! Caution
Never use anything to force ice from the evaporator.
Damage may result.
! Warning
Disconnect electric power to the ice machine (and
dispenser if applicable) at the electric switch box
before proceeding.
Step 2 Remove all ice from the bin.
Step 3 Refer to Removal of Parts For Cleaning/
Sanitizing and remove ice machine parts.
Step 4 Mix a solution of water and sanitizer.
Solution Type
Sanitizer
Water
4 gal. (15 l)
Mixed With
3 oz (90 ml) sanitizer
D. Bin or dispenser
Step 6 Rinse all sanitized areas with clear water.
Step 7 Install the removed parts, restore power and
place toggle switch in the ICE position.
Step 8 To start a sanitizing cycle, move the toggle
switch to the CLEAN position. The water will flow
through the water dump valve and down the drain. The
Clean light will turn on to indicate the ice machine is in
the Sanitizing mode.
Step 9 Wait about two minutes or until water starts to
flow over the evaporator.
Step 10 Add the proper amount of Manitowoc Ice
Machine Sanitizer to the water trough by pouring
between water curtain and evaporator.
Model
S300/S320/S420
S450/S500/S600/S850/
S1000/S1200
S1400/S1600/S1800
Amount of Sanitizer
3 ounces (90 ml)
3 ounces (90 ml)
6 ounces (180 ml)
Step 11 The ice machine will automatically time out a
ten minute sanitizing cycle, followed by six rinse cycles,
and stop. The Clean light will turn off to indicate the
Cleaning cycle is completed. This entire cycle lasts
approximately 30 minutes.
Step 12 When the sanitizing process stops, move the
toggle switch to ICE position.
Part Number 000000345
4-5
Maintenance
Section 4
REMOVAL OF PARTS FOR CLEANING/SANITIZING
1. Turn off the electrical and water supply to the ice
machine (and dispenser when applicable).
5. Use a soft-bristle brush or sponge (NOT a wire
brush) to carefully clean the parts.
! Caution
! Warning
Disconnect electric power to the ice machine (and
dispenser if applicable) at the electric switch box
before proceeding.
! Caution
2. Remove all ice from the bin.
3. Remove the water curtain and the components you
want to clean or sanitize. See the following pages for
removal procedures for these parts.
! Warning
Wear rubber gloves and safety goggles (and/or face
shield) when handling Ice Machine Cleaner or
Sanitizer.
4. Soak the removed part(s) in a properly mixed
solution.
Solution Type
Cleaner
Sanitizer
4-6
Water
1 gal. (4 l)
4 gal. (15 l)
Do not mix Cleaner and Sanitizer solutions together.
It is a violation of Federal law to use these solutions
in a manner inconsistent with their labeling.
Mixed With
16 oz (500 ml) cleaner
3 oz (90 ml) sanitizer
Do not immerse the water pump motor in the
cleaning or sanitizing solution.
6. Use the sanitizing solution and a sponge or cloth to
sanitize (wipe) the interior of the ice machine and
the entire inside of the bin/dispenser.
7. Thoroughly rinse all of the parts and surfaces with
clear water.
8. Install the removed parts.
NOTE: Incomplete rinsing of the ice thickness probe or
water level probe may leave a residue. This could cause
the ice machine to malfunction. For best results, brush or
wipe the probes off while rinsing it. Thoroughly dry the
probes before installing them.
9. Turn on the water and electrical supply.
Part Number 000000345
Section 4
Maintenance
Water Curtain
Removing the Front Panels
NOTE: The front panels do not normally have to be
removed. If needed perform the following procedure.
1. Loosen screws. Do not remove they are retained by
o-rings to prevent loss.
2. 30 Inch and 48 Inch Models Only: To remove right
front door lift up and remove (22 inch machines have
a single door, proceed to step 3).
A. Gently flex the curtain in the center and remove
it from the right side.
B. Slide the left pin out.
STEP 1
STEP 2
5
3
SV3153
Water Curtain Removal
2
Door Removal
3. Open left front door to 45 degrees.
4. Support with left hand, depress top pin, tilt top of
door forward and lift out of bottom pin to remove.
Part Number 000000345
4-7
Maintenance
Section 4
Water Distribution Tube
Ice Thickness Probe
A. Compress the hinge pin on the top of the ice
thickness probe.
COMPRESS
HINGE PIN TO
REMOVE
! Warning
Removing the distribution tube while the water
pump is running will allow water to spray from ice
machine. Disconnect the electrical power to the ice
machine and dispenser at the electric service switch
box and turn off the water supply.
NOTE: Distribution tube thumbscrews are retained by orings to prevent loss. Loosen thumbscrews but do not
pull thumbscrews out of distribution tube.
A
B
SV3135
Ice Thickness Probe Removal
B. Pivot the ice thickness probe to disengage one
pin then the other. The ice thickness probe can
be cleaned at this point without complete
removal. Follow Step C for complete removal.
! Warning
Disconnect the electric power to the ice machine at
the electric service switch box.
C. Disconnect the ice thickness control wiring from
the control board.
4-8
Water Distribution Tube Removal
A. Remove outer half of distribution tube by
loosening the four (4) thumbscrews (o-rings
retain thumbscrews to distribution tube).
B. Pull inner half of water distribution tube forward
to release slip joint from water pump tubing
connection.
Part Number 000000345
Section 4
Maintenance
Water Level Probe
Water Trough
A. Depress tabs on right and left side of the water
trough.
B. Allow front of water trough to drop as you pull
forward to disengage the rear pins.
1. Remove the water trough.
! Warning
Disconnect the electrical power to the ice machine
at the electrical disconnect before proceeding.
2. The water level probe normally does not require
removal for cleaning. The probe can be wiped and
cleaned in place or proceed to step 3.
3. Pull the water level probe straight down to
disengage.
4. Lower the water level probe until the wiring
connector is visible. Disconnect the wire lead from
the water level probe.
5. Remove the water level probe from the ice machine.
DEPRESS TABS
WATER LEVEL PROBE
Part Number 000000345
SV3141
4-9
Maintenance
Section 4
Evaporator Tray Removal
Water Pump
1. Remove the water trough.
! Warning
Disconnect the electric power to the ice machine at
the electric service switch box and turn off the water
supply before proceeding.
2. Remove thumbscrew on left side of tray.
3. Allow left side of tray to drop as you pull the tray to
the left side. Continue until the outlet tube
disengages from the right side.
1. Empty the water trough.
A. Move the toggle switch from OFF to ICE.
B. Wait 45 seconds.
C. Place toggle switch in OFF position.
WATER
PUMP
WATER
PUMP BASE
SV3091
Water Pump Removal
2. Remove the water trough.
3. The water pump normally does not require removal
for cleaning. The water pump base can be wiped
and cleaned in place or proceed to step 4.
4. Grasp pump and pull straight down on pump
assembly until water pump disengages and
electrical connector is visible.
5. Disconnect the electrical connector.
6. Remove the water pump assembly from ice
machine.
7. Do not soak the water pump in cleaner or sanitizer.
Wipe the pump and ice machine base clean.
4-10
Part Number 000000345
Section 4
Maintenance
Drain Line Check Valve
Water Inlet Valve
The drain line check valve normally does not require
removal for cleaning. Water loss from the sump trough
will indicate removal and cleaning are required.
The water inlet valve normally does not require removal
for cleaning. Refer to Section 5 for a list of causes for
“No Water Entering Water Trough” or “Water Overflows
Water Trough.
1. When the ice machine is off, the water inlet valve
must completely stop water flow into the machine.
sv3154
1. Remove check valve and tube assembly.
A. Tip assembly to right until tubing disengages.
2. When the ice machine is on, the water inlet valve
must allow the proper water flow through it. Set the
toggle switch to ON. Watch for water flow into the ice
machine. If the water flow is slow or only trickles into
the ice machine, refer to Section 5.
Follow the procedure below to remove the water inlet
valve.
B. Lift up on assembly to remove.
2. Remove insulation from check valve assembly.
3. Remove vinyl tubing from top of check valve.
4. Soak in cleaner solution 10 minutes, and then flush
with water to remove debris.
! Warning
Disconnect the electric power to the ice machine
and dispenser at the electric service switch box and
turn off the water supply before proceeding.
1. Remove the 1/4” hex head screws.
2. Remove, clean, and install the filter screen.
FILTER
ACCESS
SCREWS
WATER
INLET
VALVE
SV1622
Part Number 000000345
4-11
Maintenance
Section 4
Water Dump Valve
The water dump valve normally does not require
removal for cleaning. To determine if removal is
necessary:
1. Locate the water dump valve.
2. Set the toggle switch to ICE.
3. While the ice machine is in the freeze mode, check
the water trough to determine if the dump valve is
leaking. If there is no or little water in the water
trough (during the freeze cycle) the dump valve is
leaking.
Important
The plunger and the inside of the enclosing tube
must be completely dry before assembly.
NOTE: During cleaning, do not stretch or damage the
spring.
6. Remove the tubing from the dump valve by twisting
the clamps off.
7. Remove the valve body, twist off.
A. If the dump valve is leaking, remove,
disassemble and clean it.
COIL
SPRING
B. If the dump valve is not leaking, do not remove
it. Instead, follow the “Ice Machine Cleaning
Procedure”.
Follow the procedure below to remove the dump valve.
! Warning
PLUNGER
NYLON GASKET
Disconnect the electric power to the ice machine at
the electric service switch box and turn off the water
supply before proceeding.
DIAPHRAM
1. If so equipped, remove the water dump valve shield
from its mounting bracket.
2. Leaving the wires attached, twist coil and rotate it
counter-clockwise1/4 turn.
MOUNTING BRACKET
3. Lift the coil assembly off the valve body.
4. Remove the spring, plunger, and nylon gasket from
the valve body.
5.
NOTE: At this point, the water dump valve can easily be
cleaned. If complete removal is desired, continue with
step 5.
VALVE BODY
Dump Valve Disassembly
4-12
Part Number 000000345
Section 4
Maintenance
Removal from Service/Winterization
GENERAL
Special precautions must be taken if the ice machine is
to be removed from service for an extended period of
time or exposed to ambient temperatures of 32°F (0°C)
or below.
! Caution
WATER-COOLED ICE MACHINES
1. Perform steps 1-6 under “Self-Contained Air-Cooled
Ice Machines.”
2. Disconnect the incoming water and drain lines from
the water-cooled condenser.
3. Insert a large screwdriver between the bottom spring
coils of the water regulating valve. Pry upward to
open the valve.
If water is allowed to remain in the ice machine in
freezing temperatures, severe damage to some
components could result. Damage of this nature is
not covered by the warranty.
Follow the applicable procedure below.
SELF-CONTAINED AIR-COOLED ICE MACHINES
1. Disconnect the electric power at the circuit breaker
or the electric service switch.
2. Turn off the water supply.
3. Remove the water from the water trough.
4. Disconnect and drain the incoming ice-making water
line at the rear of the ice machine.
5. Energize the ice machine and wait one minute for
the water inlet valve to open.
6. Blow compressed air in both the incoming water and
the drain openings in the rear of the ice machine
until no more water comes out of the inlet water lines
or the drain.
7. Make sure water is not trapped in any of the water
lines, drain lines, distribution tubes, etc.
SV1624
Pry Open the Water Regulating Valve
4. Hold the valve open and blow compressed air
through the condenser until no water remains.
REMOTE ICE MACHINES
1. Move the ICE/OFF/CLEAN switch to OFF.
2. “Frontseat” (shut off) the receiver service valves.
Hang a tag on the switch as a reminder to open the
valves before restarting.
3. Perform steps 1-6 under “Self-Contained Air-Cooled
Ice Machines.”
AUCS® Accessory
Refer to the AuCS® Accessory manual for winterization
of the AuCS® Accessory.
Part Number 000000345
4-13
Maintenance
Section 4
THIS PAGE INTENTIONALLY LEFT BLANK
4-14
Part Number 000000345
Section 5
Before Calling For Service
Section 5
Before Calling For Service
Checklist
If a problem arises during operation of your ice machine, follow the checklist below before calling service. Routine
adjustments and maintenance procedures are not covered by the warranty.
Problem
Ice machine does not operate.
Ice machine stops, and can be restarted
by moving the toggle switch to OFF and
back to ICE.
Ice machine does not release ice or is
slow to harvest.
Ice machine does not cycle into harvest
mode.
Possible Cause
No electrical power to the ice machine
and/or condensing unit.
High pressure cutout tripping.
ICE/OFF/CLEAN toggle switch set
improperly.
Water curtain stuck open.
Remote receiver service valve and/or
Liquid/suction line shut off valves are
closed.
Safety limit feature stopping the ice
machine.
Ice machine is dirty.
Ice machine is not level.
Low air temperature around ice machine
head section.
Fan cycling control does not de-energize
condenser fan motor.
The six-minute freeze time lock-in has
not expired yet.
Ice thickness probe is dirty.
Ice thickness probe is disconnected.
Ice thickness probe is out of adjustment.
Uneven ice fill (thin at the top of
evaporator).
Ice quality is poor (soft or not clear).
Poor incoming water quality.
Water filtration is poor.
Ice machine is dirty.
Water dump valve is not working.
Water softener is working improperly (if
applicable).
Part Number 000000345
To Correct
Replace the fuse/reset the breaker/turn
on the main switch.
Clean condenser coil. (See Section 4)
Move the toggle switch to the ICE
position.
Water curtain must be installed and
swinging freely. (See Section 4)
Open the valve(s). (See Section 2)
Refer to “Safety Limit Feature” on the
next page.
Clean and sanitize the ice machine.
(See Section 4)
Level the ice machine. (See Section 2)
Air temperature must be at least 35°F
(1.6°C).
Verify pressure is below cut-out setpoint,
replace fan cycling control.
Wait for the freeze lock-in to expire.
Clean and sanitize the ice machine.
(See Section 4)
Connect the wire.
Adjust the ice thickness probe.
(See Section 3)
Verify sufficient water level in sump
trough. Contact a qualified service
company to check refrigeration system.
Contact a qualified service company to
test the quality of the incoming water and
make appropriate filter
recommendations.
Replace the filter.
Clean and sanitize the ice machine.
(See Section 4)
Disassemble and clean the water dump
valve. (See Section 4)
Repair the water softener.
5-1
Before Calling For Service
Problem
Ice machine produces shallow or
incomplete cubes, or the ice fill pattern on
the evaporator is incomplete.
Low ice capacity.
Section 5
Possible Cause
Ice thickness probe is out of adjustment.
To Correct
Adjust the ice thickness probe.
(See Section 4)
Water trough level is too low.
Check the water level probe for damage.
(See Section 3)
Water inlet valve filter screen is dirty.
Remove the water inlet valve and clean
the filter screen. (See Section 4)
Water filtration is poor.
Replace the filter.
Hot incoming water.
Connect the ice machine to a cold water
supply. (See Section 2)
Water inlet valve is not working.
Replace the water inlet valve.
Incorrect incoming water pressure.
Water pressure must be 20-80 psi
(1.4 bar - 5.5 bar)
Ice machine is not level.
Level the ice machine.
(See Section 2)
Water inlet valve filter screen is dirty.
Remove the water inlet valve and clean
the filter screen. (See Section 4)
Incoming water supply is shut off.
Open the water service valve.
Water inlet valve stuck open or leaking.
Place toggle switch in OFF position, if
water continues to enter water trough
replace the water inlet valve.
The condenser is dirty.
Clean the condenser. (See Section 4)
High air temperature entering condenser. Air temperature must not exceed 120°F
The harvest assist air compressor is not
functioning.
Safety Limit Feature
In addition to the standard safety controls, such as the
high pressure cutout, your Manitowoc ice machine
features built-in safety limits which will stop the ice
machine if conditions arise which could cause a major
component failure.
Before calling for service, re-start the ice machine using
the following procedure:
(39°C)
Call for service.
1. Move the ICE/OFF/CLEAN switch to OFF and then
back to ICE.
A. If the safety limit feature has stopped the ice
machine, it will restart after a short delay.
Proceed to step 2.
B. If the ice machine does not restart, see “Ice
machine does not operate” on the previous
page.
2. Allow the ice machine to run to determine if the
condition is recurring.
A. If the ice machine stops again, the condition has
recurred. Call for service.
B. If the ice machine continues to run, the condition
has corrected itself. Allow the ice machine to
continue running.
5-2
Part Number 000000345
Section 5
Before Calling For Service
THIS PAGE INTENTIONALLY LEFT BLANK
Part Number 000000345
5-3
Before Calling For Service
Section 5
THIS PAGE INTENTIONALLY LEFT BLANK
5-4
Part Number 000000345
MANITOWOC ICE, INC.
2110 South 26th Street P.O. Box 1720
Manitowoc, WI 54221-1720
Phone: (920) 682-0161
Service Fax: (920) 683-7585
Web Site - www.manitowocice.com
© 2006 Manitowoc Ice, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising