ICOM IC-7000 Instruction manual

INSTRUCTION MANUAL
HF/VHF/UHF
ALL MODE TRANSCEIVER
i7000
IMPORTANT
READ THIS INSTRUCTION MANUAL
CAREFULLY before attempting to operate the
transceiver.
EXPLICIT DEFINITIONS
WORD
DEFINITION
R WARNING
Personal injury, fire hazard or electric
shock may occur.
SAVE THIS INSTRUCTION MANUAL. This
CAUTION
manual contains important safety and operating instructions for the IC-7000.
NOTE
FOREWORD
We understand that you have a choice of many different radios in the market place. We want to take a couple of moments of your time to thank you for making
the IC-7000 your radio of choice, and hope you agree
with Icom’s philosophy of “technology first.” Many
hours of research and development went into the design of your IC-7000.
D FEATURES
❍ IF DSP features
❍ All mode capability covering 160–2 m and
70 cm (depending on version)
❍ Compact with detachable front panel
❍ ±0.5 ppm of high frequency stability
❍ Baudot RTTY demodulator
❍ Simple band scope function
❍ Selectable SSB transmission passband
width (For both higher and lower pass frequency)
❍ Standard voice synthesizer/voice recorder
Spurious signals may be received near the following frequencies. These are created in the internal circuit and does
not indicate a transceiver malfunction:
52.76497 MHz,
443.03535 MHz
Equipment damage may occur.
If disregarded, inconvenience only. No
risk or personal injury, fire or electric
shock.
SUPPLIED ACCESSORIES
The transceiver comes with the following accessories.
Qty.
q Hand microphone (HM-151) ........................... 1
w DC power cable (OPC-1457) .......................... 1
e Spare fuse (ATC 5 A) ...................................... 1
r Spare fuse (ATC 30 A) .................................... 2
t ACC cable ........................................................1
y 3.5 (d) mm plug ................................................1
u 6.5 (d) mm Electronic keyer plug......................1
i Microphone hanger...........................................1
q
w
e
t
y
r
u
i
Icom, Icom Inc. and the
logo are registered trademarks
of Icom Incorporated (Japan) in the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other
countries.
OPEN
THIS PAGE
PAGE
i-1
ILLUSTRATIONS
Front panel
!6
@4 @3
@2
@1 @0 !9 !8
!7
q
w
e
!5
t yu i
!0 !1 !2
o
!4
!3
r
HM-151
⁄3
z
SPCH
/LOCK
TUNER
/CALL
XFC
V/M
MW
F-1
F-2
x
c
v
.
,
1.8
10
b
⁄2
⁄1
21
50
1
4
7
.
3.5
14
24
2
5
8
144
0
7
18
28
3
MODE
6
FIL
9
GENE
430
CE
⁄0
Mic element
m
n
F-INP
ENT
The front panel and HM-151’s panel
descriptions are descrived on pages
1 to 4, and on page 9, respectively
(see the Chapter 1 (Panel description) for more details).
i-2
■ Front panel
■ Microphone (HM-151)
q AF GAIN CONTROL [AF] (inner control; p. 33)
z SPCH/LOCK KEY [SPCH/LOCK] (p. 34, 37)
w RF GAIN CONTROL/SQUELCH CONTROL
[RF/SQL] (outer control; p. 35)
x PTT SWITCH [PTT] (p. 37)
e POWER KEY [PWR] (p. 25)
r FRONT PANEL LATCH (p. 16)
t PASSBAND TUNING/M-ch/RIT CONTROLS
[PBT/M-ch/RIT] (pgs. 73, 77, 86, 100, 104)
y TWIN PBT (M-ch/RIT) INDICATOR
(pgs. 73, 77, 86, 100)
v TRANSMIT INDICATOR (p. 37)
b KEYPAD (pgs. 28, 29)
n FILTER SELECTION [FIL] (p. 75)
m MODE KEY [MODE] (p. 34)
, POWER INDICATOR
u MENU/GROUP KEYS [MENU/GRP] (p. 151)
. PROGRAMMABLE FUNCTION KEYS [F-1]/[F-2]
i TUNER/CALL KEY [TUNER/CALL]
(pgs. 100, 114)
⁄0 MEMORY WRITE [MW] (pgs. 101, 102)
o MULTI-FUNCTION KEYS [F1]/[F2]/[F3]/[F4]
(pgs. 5–8, 151)
!0 MANUAL NOTCH KEY [MNF/ADJ] (p. 81)
!1 AUTO NOTCH/VOICE RECORDER KEY
[ANF/• REC] (pgs. 80, 93)
!2 SPCH/LOCK KEY [SPCH/LOCK] (pgs. 34, 37)
!3 MICROPHONE CONNECTOR (p. 10)
Z(BAND)]
!4 UP/DOWN (BAND) KEYS [Y(BAND)]/[Z
!5 MAIN DIAL TENSION LATCH
!6 HEADPHONE JACK [PHONES] (p. 18)
!7 MAIN DIAL [DIAL]
!8 RECEIVE/TRANSMIT INDICATORS [RX]/[TX]
!9 TUNING STEP KEY [TS] (pgs. 30–32)
@0 NOISE BLANKER KEY [NB/ADJ] (p. 78)
@1 NOISE REDUCTION KEY [NR/LEV] (p. 79)
@2 FUNCTION DISPLAY (p. 13)
@3 PRE AMP/ATTENUATOR KEY [P.AMP/ATT]
(p. 72)
@4 MODE KEY [MODE] (p. 34)
i-3
Y]/[Z
Z]
c UP/DOWN SWITCHES [Y
⁄1 VFO/MEMORY SELECTION [V/M]
(pgs. 27, 100, 107)
⁄2 TRANSMIT FREQUENCY CHECK [XFC]
(pgs. 65, 89)
⁄3 TUNER/CALL KEY [TUNER/CALL]
(pgs. 100, 114)
PRECAUTIONS
R WARNING RF EXPOSURE! This device emits
Radio Frequency (RF) energy. Extreme caution should be
observed when operating this device. If you have any
questions regarding RF exposure and safety standards
please refer to the Federal Communications Commission
Office of Engineering and Technology’s report on Evaluating Compliance with FCC Guidelines for Human Radio
Frequency Electromagnetic Fields (OET Bulletin 65).
R WARNING HIGH VOLTAGE! NEVER touch an
antenna or internal antenna connector during transmission. This may result in an electrical shock or burn.
R WARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—anything less may result in an accident.
R NEVER apply AC power to the [DC13.8V] socket on
the transceiver rear panel. This could cause a fire or damage the transceiver.
R NEVER apply more than 16 V DC, such as a 24 V
battery, to the [DC13.8V] socket on the transceiver rear
panel. This could cause a fire or damage the transceiver.
R NEVER let metal, wire or other objects touch any internal part or connectors on the rear panel of the transceiver. This may result in an electric shock or this could
cause a fire or damege the transceiver.
R NEVER connect or use the supplied HM-151 (microphone) with other transceiver. This could cause damage
to the transceiver. The HM-151 is designed for use with
the IC-7000 ONLY.
NEVER expose the transceiver to rain, snow or any liquids.
AVOID using or placing the transceiver in areas with temperatures below –10°C (+14°F) or above +60°C (+140°F).
Be aware that temperatures on a vehicle’s dashboard can
exceed +80°C (+176°F), resulting in permanent damage
to the transceiver if left there for extended periods.
AVOID placing the transceiver in excessively dusty environments or in direct sunlight.
AVOID placing the transceiver against walls or putting
anything on top of the transceiver. This will obstruct heat
dissipation.
Place unit in a secure place to avoid inadvertent use by
children.
During mobile operation, NEVER place the transceiver
where air bag deployment may be obstructed.
During mobile operation, DO NOT place the transceiver
where hot or cold air blows directly onto it.
During mobile operation, DO NOT operate the transceiver
without running the vehicle’s engine. When the transceiver’s power is ON and your vehicle’s engine is OFF,
the vehicle’s battery will soon become exhausted.
Make sure the transceiver power is OFF before starting
the vehicle engine. This will avoid possible damage to the
transceiver by ignition voltage spikes.
During maritime mobile operation, keep the transceiver
and microphone as far away as possible from the magnetic navigation compass to prevent erroneous indications.
BE CAREFUL! The rear panel will become hot when operating the transceiver continuously for long periods.
BE CAREFUL! If a linear amplifier is connected, set the
transceiver’s RF output power to less than the linear amplifier’s maximum input level, otherwise, the linear amplifier will be damaged.
Use Icom microphones only (supplied or optional). Other
manufacturer’s microphones have different pin assignments, and connection to the IC-7000 may damage the
transceiver.
For U.S.A. only
Caution: Changes or modifications to this transceiver,
not expressly approved by Icom Inc., could void your
authority to operate this transceiver under FCC regulations.
ii
TABLE OF CONTENTS
IMPORTANT …………………………………………i-1
FOREWORD ………………………………………… i-1
EXPLICIT DEFINITIONS …………………………… i-1
SUPPLIED ACCESSORIES …………………………i-1
ILLUSTRATIONS ……………………………………i-2
■ Front panel ……………………………………… i-3
■ Microphone (HM-151) ………………………… i-3
PRECAUTIONS ………………………………………ii
TABLE OF CONTENTS …………………………… iii
1 PANEL DESCRIPTION
………………… 1–14
■ Front panel ………………………………………… 1
■ Multi-function keys ……………………………… 5
D Menu M-1 functions …………………………… 5
D Menu M-2 functions …………………………… 5
D Menu M-3 functions …………………………… 5
D Menu S-1 functions …………………………… 7
D Menu S-2 functions …………………………… 7
D Menu S-3 functions …………………………… 8
D Menu G-1 (Scope) functions ………………… 8
■ Microphone (HM-151) …………………………… 9
D Microphone connector ……………………… 10
■ Rear panel ……………………………………… 11
D DATA socket …………………………………… 12
D ACC socket …………………………………… 12
■ Function display ………………………………… 13
2 INSTALLATION AND CONNECTIONS 15–24
■ Unpacking ……………………………………… 15
■ Selecting a location……………………………… 15
■ Grounding………………………………………… 15
■ Antenna connection……………………………… 15
■ Installation ……………………………………… 16
D Single body mounting ………………………… 16
D Stand …………………………………………… 16
D Front panel separation ……………………… 16
D Front panel mounting ………………………… 16
■ Required connections…………………………… 17
■ Advanced connections ………………………… 18
■ Power supply connections……………………… 19
■ Connecting a DC power supply ……………… 19
■ Battery connections …………………………… 19
■ External antenna tuners………………………… 20
■ Linear amplifier connections …………………… 21
■ Connections for CW …………………………… 22
■ Connections for RTTY ………………………… 23
D Connections for RTTY (FSK)………………… 23
D Connections for RTTY (AFSK) ……………… 23
■ Connections for packet, SSTV or PSK31 …… 24
D When connecting to [DATA] socket ………… 24
D When connecting to [ACC] socket ………… 24
D When connecting to [MIC] connector ……… 24
3 BASIC OPERATION ……………………25–38
■ When first applying power (CPU resetting)…… 25
D Menu resetting (M-1)………………………… 25
■ Initial settings …………………………………… 25
■ VFO description ………………………………… 26
iii
D Differences between VFO and
memory mode ………………………………… 26
■ VFO operation …………………………………… 27
D Selecting VFO A/VFO B ……………………… 27
D VFO equalization ……………………………… 27
■ Selecting VFO/memory mode ………………… 27
■ Selecting an operating band …………………… 28
D Using the band stacking registers…………… 28
■ Frequency setting ……………………………… 29
D Tuning with the main dial …………………… 29
D Direct frequency entry
with the microphone’s keypad ……………… 29
D Programmable tuning step…………………… 30
D Selecting “kHz” step ………………………… 30
D Selecting 1 Hz or 10 Hz step
(SSB/CW/RTTY only) ………………………… 31
D 1 MHz quick tuning step
(FM/WFM/AM only) …………………………… 31
D 1⁄4 tuning function (CW/RTTY only) ………… 32
D Auto tuning step function …………………… 33
D Band edge warning beep …………………… 33
■ Volume setting …………………………………… 33
■ Operating mode selection ……………………… 34
■ Voice synthesizer function ……………………… 34
■ Squelch and receive (RF) sensitivity ………… 35
■ Meter function …………………………………… 36
D Multi-function meter…………………………… 36
■ Lock functions …………………………………… 37
D Dial lock function ……………………………… 37
D Microphone lock function …………………… 37
■ Basic transmit operation ……………………… 37
D Transmitting …………………………………… 37
D Setting output power ………………………… 38
D Setting microphone gain……………………… 38
4 RECEIVE AND TRANSMIT …………… 39–69
■ Operating SSB…………………………………… 39
D Convenient functions for receive …………… 39
D Convenient functions for transmit …………… 40
D About 5 MHz band operation
(USA version only) …………………………… 40
■ Operating CW …………………………………… 41
D Convenient functions for receive …………… 42
D Convenient functions for transmit …………… 42
D CW reverse mode …………………………… 43
D CW side tone function………………………… 43
D CW pitch control ……………………………… 44
■ Electronic CW keyer …………………………… 45
D Memory keyer send menu …………………… 46
D Editing a keyer memory ……………………… 47
D Contest number set mode …………………… 48
1 Number Style ……………………………… 48
2 Count UP Trigger …………………………… 48
3 Present Number …………………………… 48
D Keyer set mode ……………………………… 49
1 Keyer Repeat Time ………………………… 49
2 Dot/Dash Ratio ……………………………… 49
3 Rise Time …………………………………… 50
TABLE OF CONTENTS
4 Paddle Polarity ……………………………… 50
5 Keyer Type ………………………………… 50
6 MIC U/D Keyer (HM-103) ………………… 50
D Paddle operation from [MIC] connector …… 50
■ Operating RTTY (FSK) ………………………… 51
D Convenient functions for receive …………… 52
D RTTY reverse mode ………………………… 53
D Twin peak filter ………………………………… 53
D Functions for the RTTY decoder indication… 54
D Setting the decoder threshold level ………… 54
D RTTY decode set mode ……………………… 55
1 RTTY Decode USOS ……………………… 55
2 RTTY Decode New Line Code …………… 55
D Pre-setting for using RTTY terminal or TNC … 56
■ Operating AM …………………………………… 57
D Convenient functions for receive …………… 57
D Convenient functions for transmit …………… 58
■ Operating FM …………………………………… 59
D Convenient functions for receive …………… 59
D Convenient functions for transmit …………… 59
D Tone squelch operation ……………………… 60
D DTCS operation ……………………………… 61
D Tone scan operation ………………………… 62
■ Repeater operation ……………………………… 63
D One-touch repeater function ………………… 63
D Repeater tone frequency …………………… 64
D Transmit frequency monitor check ………… 65
D Auto repeater function (USA version only) … 65
D Storing a non standard repeater …………… 66
■ 1750 Hz tone burst ……………………………… 67
■ DTMF memory encoder ………………………… 67
D DTMF send menu …………………………… 67
D Programming a DTMF code ………………… 68
D DTMF speed…………………………………… 68
5 FUNCTIONS FOR RECEIVE…………… 69–82
■ Simple band scope ……………………………… 69
D Fix mode ……………………………………… 70
D Center mode…………………………………… 71
D Scope set mode ……………………………… 71
1 Max Hold …………………………………… 72
2 Scope Size ………………………………… 72
3 FAST Sweep………………………………… 72
4 FAST Sweep Sound ……………………… 72
■ Preamp and attenuator ………………………… 72
■ RIT function ……………………………………… 73
■ AGC function …………………………………… 74
D AGC time constant selection ………………… 74
D Setting the AGC time constant ……………… 74
■ IF filter selection ………………………………… 75
D IF filter selection ……………………………… 75
D Filter passband width setting
(SSB/CW/RTTY/AM only) …………………… 76
D IF filter shape (SSB/CW only) ……………… 76
■ Twin PBT operation …………………………… 77
■ Noise blanker …………………………………… 78
D Noise blanker set mode ……………………… 78
1 NB Level …………………………………… 78
2 NB Width …………………………………… 78
■ Noise reduction ………………………………… 79
D Noise reduction set mode …………………… 79
➥ NR Level …………………………………… 79
■ Notch function …………………………………… 80
D Auto notch function …………………………… 80
D Manual notch function………………………… 81
D Manual notch filter set mode ………………… 81
■ Voice squelch control function ………………… 82
■ Meter peak hold function ……………………… 82
6 FUNCTIONS FOR TRANSMIT ………… 83–92
■ VOX function …………………………………… 83
D Adjusting the VOX function ………………… 83
D VOX set mode ………………………………… 84
1 VOX Gain …………………………………… 84
2 Anti-VOX …………………………………… 84
3 VOX Delay ………………………………… 84
■ Transmit filter width setting (SSB only) ……… 84
■ Break-in function ………………………………… 85
D Semi break-in operation ……………………… 85
D Full break-in operation ……………………… 85
■ ∂TX function …………………………………… 86
■ Monitor function ………………………………… 87
■ Speech compressor …………………………… 87
D Compression level setting …………………… 88
➥ COMP Level ……………………………… 88
■ Split frequency operation ……………………… 89
■ Quick split function ……………………………… 90
D Split offset frequency setting ………………… 91
D Quick split setting …………………………… 91
■ Measuring SWR ………………………………… 92
D Spot measurement …………………………… 92
D Plot measurement …………………………… 92
7 VOICE RECORDER FUNCTIONS …… 93–99
1
2
3
4
5
6
7
8
9
10
11
■ Digital voice recorder …………………………… 93
■ Recording a received audio …………………… 93
D Basic recording ……………………………… 93
D One-touch voice recording…………………… 94
■ Playing the recorded contents ………………… 94
■ Erasing the recorded contents ………………… 95
■ Recording a message for transmit …………… 96
D Recording ……………………………………… 96
D Confirming/Erasing the recorded message… 96
■ Programming a memory name for transmit … 97
■ Sending a recorded message ………………… 98
D Transmit level setting ………………………… 98
■ Voice set mode ………………………………… 99
D Voice set mode ……………………………… 99
1 Auto Monitor ………………………………… 99
2 MIC Memo…………………………………… 99
18
8 MEMORY OPERATION ……………… 100–110
19
■ Memory channels ……………………………… 100
■ Memory channel selection …………………… 100
■ Memory programming ………………………… 101
D Programming in VFO mode………………… 101
D Programming in memory mode …………… 102
■ Memory channel list …………………………… 103
12
13
14
15
16
17
20
21
iv
TABLE OF CONTENTS
D Selecting a memory channel
using the memory channel list……………… 103
D Setting a memory channel
as a select memory ………………………… 104
D Selecting a memory bank ………………… 104
D Memory names ……………………………… 105
■ Memory clearing ……………………………… 106
D Memory clearing
using the memory channel list……………… 106
■ Frequency transferring………………………… 107
D Transferring in VFO mode ………………… 107
D Transferring in memory mode ……………… 108
■ Memo pads …………………………………… 109
D Writing frequencies and operating modes
into memo pads ……………………………… 109
D Calling up a frequency from a memo pad … 110
9 SCAN OPERATION ………………… 111–113
■ Scan types ……………………………………… 111
■ Preparation ……………………………………… 111
■ Programmed scan operation ………………… 112
■ Memory scan operation ……………………… 112
■ Select memory scan operation ……………… 113
■ Priority watch …………………………………… 113
10 ANTENNA TUNER OPERATION … 114–115
■ Optional AT-180 AUTOMATIC ANTENNA TUNER
operation………………………………………… 114
D Tuner operation ……………………………… 114
D Manual tuning………………………………… 114
■ Optional AH-4 AUTOMATIC ANTENNA TUNER
operation………………………………………… 115
D AH-4 operation ……………………………… 115
11 PACKET OPERATION …………………… 116
■ Packet operation ……………………………… 116
D Data socket…………………………………… 116
D Adjusting the data speed …………………… 116
D Adjusting the transmit signal output
from the TNC ………………………………… 116
12 CLOCK AND TIMERS ……………… 117–119
■ Time set mode ………………………………… 117
1 Year ………………………………………… 117
2 Date ………………………………………… 117
3 Time (Now) ………………………………… 117
4 CLOCK2 Function ………………………… 117
5 CLOCK2 Offset …………………………… 117
6 Auto Power OFF …………………………… 117
D Setting the current year …………………… 118
D Setting the current date …………………… 118
D Setting the current time …………………… 118
D Clock2 function activity ……………………… 119
D Clock2 offset setting ………………………… 119
D Auto power OFF activity …………………… 119
13 SET MODE ………………………… 120–136
■ Set mode description ………………………… 120
v
■ Quick set mode ………………………………… 121
➥ RF Power (all modes) ……………………… 121
➥ MIC Gain (SSB/AM/FM modes)…………… 121
➥ SSB TBW (WIDE) L (SSB mode) ………… 121
➥ SSB TBW (WIDE) H (SSB mode) ………… 122
➥ SSB TBW (MID) L (SSB mode) …………… 122
➥ SSB TBW (MID) H (SSB mode) ………… 122
➥ SSB TBW (NAR) L (SSB mode) ………… 122
➥ SSB TBW (NAR) H (SSB mode) ………… 122
➥ Key Speed (CW mode) …………………… 122
➥ CW Pitch (CW mode) ……………………… 122
➥ Side Tone Level (CW mode) ……………… 123
➥ Side Tone Level Limit (CW mode)………… 123
➥ Twin Peak Filter (RTTY mode) …………… 123
➥ RTTY Mark Frequency (RTTY mode) …… 123
➥ RTTY Shift Width (RTTY mode) ………… 123
➥ RTTY Keying Polarity (RTTY mode) ……… 123
■ Display set mode ……………………………… 124
1 Contrast (LCD)……………………………… 124
2 Bright (LCD) ………………………………… 124
3 LCD Unit Bright …………………………… 124
4 LCD Flicker ………………………………… 124
5 Backlight (Switches) ……………………… 124
6 Display Type………………………………… 124
7 Display Font Type ………………………… 125
8 Display Font Size ………………………… 125
9 Meter Peak Hold …………………………… 125
10 Filter Popup (PBT) ………………………… 125
11 Filter Popup (FIL)…………………………… 125
12 1 Hz Mode Popup ………………………… 125
13 Scope CENTER/FIX Popup ……………… 125
14 TV Popup (CH Up/Down) ………………… 126
15 TV Popup (P.AMP/ATT) …………………… 126
16 Voice TX Name Display …………………… 126
17 Keyer Memory Display …………………… 126
18 DTMF Memory Display …………………… 126
19 External Display …………………………… 126
20 Opening Message ………………………… 126
21 My Call ……………………………………… 127
22 Power ON Check…………………………… 127
■ Miscellaneous (others) set mode …………… 128
1 Monitor ……………………………………… 128
2 Monitor Level ……………………………… 128
3 Beep (Confirmation) ……………………… 128
4 Beep (Band edge) ………………………… 128
5 Beep Level ………………………………… 128
6 Beep Level Limit …………………………… 128
7 RF/SQL Control …………………………… 129
8 Quick SPLIT ………………………………… 129
9 SPLIT Offset………………………………… 129
10 SPLIT LOCK………………………………… 129
11 DUP Offset HF ……………………………… 129
12 DUP Offset 50M …………………………… 129
13 DUP Offset 144M ………………………… 130
14 DUP Offset 430M ………………………… 130
15 One Touch Repeater ……………………… 130
16 Auto Repeater ……………………………… 130
TABLE OF CONTENTS
17 Tuner (Auto Start) ………………………… 130
18 Tuner (PTT start) …………………………… 131
19 [TUNER] Switch …………………………… 131
20 VSEND Select ……………………………… 131
21 SPEECH Level …………………………… 131
22 SPEECH Language ……………………… 131
23 SPEECH Speed …………………………… 131
24 SPEECH S-Level ………………………… 132
25 SPEECH [MODE] Switch ………………… 132
26 Memopad Numbers ……………………… 132
27 SCAN Speed ……………………………… 132
28 SCAN Resume …………………………… 132
29 MAIN DIAL Auto TS ……………………… 132
30 HM-151 [F-1] ……………………………… 133
31 HM-151 [F-2] ……………………………… 133
32 MIC Up/Down Speed ……………………… 133
33 Quick RIT/∂TX Clear ……………………… 133
34 SSB/CW Synchronous Tuning …………… 133
35 CW Normal Side …………………………… 134
36 VOICE 1st Menu ………………………… 134
37 KEYER 1st Menu ………………………… 134
38 DTMF 1st Menu …………………………… 134
39 Mode Select (SSB) ………………………… 134
40 Mode Select (CW) ………………………… 134
41 Mode Select (RTTY) ……………………… 134
42 Mode Select (AM) ………………………… 135
43 Mode Select (FM) ………………………… 135
44 Mode Select (WFM) ……………………… 135
45 External Keypad (VOICE) ………………… 135
46 External Keypad (KEYER) ………………… 135
47 Front Keypad Type ………………………… 136
48 CI-V Baud Rate …………………………… 136
49 CI-V Address ……………………………… 136
50 CI-V Transceive …………………………… 136
51 REF Adjust ………………………………… 136
14 MAINTENANCE ………………………… 137
■ Fuse replacement ……………………………… 137
■ Memory backup………………………………… 137
■ Cleaning ………………………………………… 137
D Codes for memory name contents ………… 147
D Split/Duplex frequency setting……………… 147
D Repeater tone/tone squelch frequency
setting ………………………………………… 147
D DTCS code and polarity setting …………… 147
18 SPECIFICATIONS ………………………… 148
■ General ………………………………………… 148
■ Transmitter ……………………………………… 148
■ Receiver ………………………………………… 148
19 OPTIONS …………………………… 149–150
20 MENU GUIDE ……………………… 151–152
21 ABOUT CE ………………………… 153–154
1
2
3
4
5
6
7
8
9
10
11
12
13
15 TROUBLESHOOTING …………… 138–139
14
16 OPTIONAL UNITS SETTING ……… 140–141
15
■ MB-106 CARRYING HANDLE …………………… 140
■ Band voltage modification …………………… 140
■ AT-180 internal switch description …………… 141
16
17 CONTROL COMMAND …………… 142–147
17
■ Remote jack (CI-V) information ……………… 142
D CI-V connection example…………………… 142
D Data format…………………………………… 142
D Command table ……………………………… 142
D To send/read memory contents …………… 146
D Band stacking register ……………………… 146
D Codes for memory keyer contents ………… 146
D Character codes for My Call ……………… 147
18
19
20
21
vi
1
PANEL DESCRIPTION
See the illustration of the Front panel on page i-2.
■ Front panel
q AF GAIN CONTROL [AF(SET)] (inner control; p. 33)
➥ Rotate to vary the audio output level from the
speaker or headphones.
Audio output
increases
• When functioning as squelch control
(RF gain is fixed at maximum.)
Noise squelch
threshold
(FM mode)
Noise squelch (FM mode)
S-meter squelch
threshold
S-meter
squelch
Squelch is
open.
Audio outut
decreases
Push momentarily to enter the set mode menu.
Lowest threshold
Highest threshold
• Push again to exit the set mode menu.
w RF GAIN CONTROL/SQUELCH CONTROL
[RF/SQL] (outer control; p. 35)
Adjusts the RF gain and squelch threshold level.
The squelch, when closed, mutes the speaker or
headphones when no signal is received, reducing
noise.
e POWER KEY [PWR] (p. 25)
➥ While transceiver’s power is OFF, push to turn the
power ON.
• The squelch is particularly effective for FM mode. It is
also available in other modes.
• 12 to 1 o’clock position is recommended for any setting
of the [RF/SQL] control.
• The control can be set to ‘Auto’ (RF gain control in SSB,
CW and RTTY; squelch control in AM, FM and WFM) or
squelch control (RF gain is fixed at maximum) in the miscellaneous (others) set mode as follows. (p. 129)
r FRONT PANEL LATCH (p. 16)
Pull away from the transceiver (towards yourself
when looking at the front of the transceiver) to detach the front panel from the main body of the transceiver.
MODE
SSB, CW
RTTY
AM, FM
WFM
SET MODE SELECTION
RF + SQL
SQL
Auto
RF GAIN
SQL
RF + SQL
SQL
SQL
RF + SQL
• Turn the DC power supply ON in advance.
➥ While transceiver’s power is ON, push and hold
for 1 sec. to turn the power OFF.
t PASSBAND TUNING/M-ch/RIT CONTROLS
[PBT/M-ch/RIT]
➥ Push inner control to toggle the twin Passband
Tuning (PBT) or memory channel/RIT function
ON and OFF.
➥ While Twin PBT is selected (p. 77):
● Adjusts the receiver’s DSP filter passband
width.
• Passband width and shift frequency are displayed
on the LCD.
• The default variable range is half of the IF filter
passband width. 25 Hz step is available.
• When functioning as RF gain/squelch control
Noise squelch (FM mode)
Squelch is
open.
RF gain
adjustable
range
Recommended level
Maximum
RF gain
● Push and hold inner control for 1 sec. to return
the PBT to default settings.
PBT1
S-meter shows
squelch level
PBT2
• When functioning as RF gain control
(Squelch is fixed open; SSB, CW, RTTY only)
–
+
Adjustable
range
Minimum RF gain
Maximum RF gain
High cut
1
Center
Low cut
PANEL DESCRIPTION
✔ What is the PBT control?
PBT electronically narrows the IF passband width to reject
interference. This transceiver uses DSP to implement PBT.
➥ While M-ch/RIT is selected:
● Rotate the inner control to select a memory
channel number (p. 100).
● Push and hold inner control for 1 sec. to turn
the RIT/∂TX mode ON (pgs. 73, 86).
Z(MENU/GRP)] to exit the RIT/∂TX mode.
• Push [Z
● While the RIT/∂TX mode is OFF:
Rotate outer control to select a memory bank
(p. 104).
● While the RIT/∂TX is ON:
Rotate outer control to shift the receive or
transmit frequency (pgs. 73, 86).
•“
” or “
” indicators appear when the RIT or
∂TX function is activate, respectively.
• The shift frequency range is ± 9.999 kHz in 1 Hz
∂TX
steps
RIT (or ±9.99 kHz in 10 Hz steps).
1
y TWIN PBT (M-ch/RIT) INDICATOR
(pgs. 73, 77, 86, 100)
➥ Indicates the status of [PBT/M-ch/RIT] (t) as the
Twin PBT function or memory channel/RIT control.
• Indicator is green when the Twin PBT is selected.
• Indicator is off when the M-ch/RIT is selected.
• Indicator is orange when the RIT or ∂TX function is
activate.
u MENU/GROUP KEYS [MENU/GRP] (p. 151)
➥ Push either key one or more times to select
M, S or G (Graphic)).
menus within a menu group (M
➥ Push and hold for 1 sec. to select one of the three
menu groups: M-1 to M-3, S-1 to S-3 and G-1
(Scope) to G-3 (SWR meter).
1
i TUNER/CALL KEY [TUNER/CALL]
➥ During HF/50 MHz operation (p. 114):
● Push momentarily to toggle the automatic antenna tuner function ON and OFF.
• An optional antenna tuner must be connected.
•“
” indicator appears when the tuner is ON.
RIT
● Push and hold for 2 sec. to manually tune the
antenna.
M-ch
• An optional antenna tuner must be connected.
•“
” indicator appears when the tuner is ON.
M-ch
Channel
decreases
Channel
increases
RIT
Frequency
decreases
Frequency
increases
• When the RIT or ∂TX function is ON, push and
hold [F-1 RIT] or [F-2 ∂TX] for 1 sec. to add or
subtract the frequency shift to the display frequency.
➥ During 144/430 MHz operation (p. 100):
Push momentarily to select the call channel (or
return to the previous channel/frequency when
the call channel is already selected).
• “C1” is the 144 MHz call channel and “C2” is the 430
MHz call channel.
o MULTI-FUNCTION KEYS [F-1]/[F-2]/[F-3]/[F-4]
➥ Push to select the function indicated in the LCD
display above these keys. (pgs. 5–8, 151)
• Functions vary depending on the active menu.
✔ What is the RIT function?
RIT (Receiver Incremental Tuning) shifts the receive frequency without shifting the transmit frequency.
This is useful for fine tuning for stations calling you off frequency or when you prefer to listen to slightly differentsounding voice characteristics, etc.
✔ What is the ∂TX function?
The ∂TX shifts the transmit frequency without shifting the receive frequency. This is useful for simple split frequency operation in CW, etc.
Functions appear
See the illustration of the Front panel on page i-2.
2
1
PANEL DESCRIPTION
!0 MANUAL NOTCH KEY [MNF/ADJ] (p. 81)
➥ Push momentarily to turn the manual notch function ON and OFF in SSB, CW and AM modes.
•“
” appears on the display when the function is activated.
➥ Push and hold for 1 sec. to enter the manual
notch filter set mode.
!5 MAIN DIAL TENSION LATCH
Selects the main dial drag.
• Three positions are available. The upper setting turns on
clicks as the dial is turned.
!6 HEADPHONE JACK [PHONES] (p. 18)
Accepts headphones with 8–16 Ω impedance.
✔ What is the notch function?
The notch function is a narrow DSP filter that removes interfering tones from CW or AM signals while preserving the desired signal's frequency response.
!1 AUTO NOTCH/VOICE RECORDER KEY
[ANF/• REC]
➥ Push momentarily to turn the auto notch function
(ANF) ON and OFF in SSB, AM, FM modes.
(p. 80)
•“
” appears on the display when the function is activated.
➥ Push and hold for 1 sec. to record the received
signal’s audio. (p. 93)
• When headphones are connected, no receive audio
comes from the speaker.
• When the PHONES/SPEAKER switch on the back of the
front panel is set to the [SPEAKER] position, an external
speaker can be used instead of headphones. This is
convenient for mobile or outdoor operation.
!2 SPCH/LOCK KEY [SPCH/LOCK]
➥ Push momentarily to have the frequency, etc. announced by the speech synthesizer. (p. 34)
• The parameters to be announced can be selected in
the miscellaneous (others) set mode. (pgs. 131, 132)
➥ Push and hold for 1 sec. to toggle the dial lock
function ON and OFF. (p. 37)
• The dial lock function electronically locks the main
dial.
•“
” appears while the dial lock function is active.
!3 MICROPHONE CONNECTOR (p. 10)
Modular-type microphone connector—accepts the
supplied microphone (HM-151).
• The optional OPC-589 can be used to connect an 8-pin
microphone such as the SM-20, if desired.
• A microphone connector is also available on the rear
panel. DO NOT connect 2 microphones simultaneously.
Z(BAND)]
!4 UP/DOWN (BAND) KEYS [Y(BAND)]/[Z
➥ Push momentarily to select a frequency band.
➥ Push and hold [Y(BAND)] for 1 sec. to toggle the
simple band scope display ON and OFF.
➥ Push and hold [Z(BAND)] for 1 sec. to toggle the
multi-function meter display ON and OFF.
Back of the front panel
!7 MAIN DIAL [DIAL]
Changes the displayed frequency and selects values for selected set mode items, etc.
!8 RECEIVE/TRANSMIT INDICATORS [RX]/[TX]
➥[RX]: Lights green in receive mode and when
squelch is open.
➥[TX]: Lights red while transmitting.
See the illustration of the Front panel on page i-2.
3
PANEL DESCRIPTION
!9 TUNING STEP KEY [TS] (pgs. 30–32)
➥ While in SSB/CW/RTTY modes, push momentarily to turn the programmable tuning step ON and
OFF. While in AM/FM/WFM modes, push momentarily to toggle the programmable tuning step
and 1 MHz quick tuning step.
• While the programmable tuning step indicator is displayed, the frequency can be changed in the programmed kHz step size.
Programmable tuning step indicator
1
@2 FUNCTION DISPLAY
Shows the operating frequency, function key menus,
simple band scope display, selected memory channel, etc. See p. 13 for details.
@3 PRE AMP/ATTENUATOR KEY [P.AMP/ATT]
(p. 72)
➥ Push momentarily to turn the preamp ON or OFF.
•“
” indicator appears when the preamp is activated.
➥ Push and hold for 1 sec. to turn the 12 dB attenuator ON; push momentarily to turn the attenuator
OFF.
•“
” indicator appears when the attenuator is activated.
1
✔ What is the preamp?
The preamp amplifies signals in the receiver front end (input)
circuit to improve the sensitivity. Turn ON ‘P.AMP’ when receiving weak signals.
✔ What is the attenuator?
• 0.01 (AM/FM/WFM mode only), 0.1, 1, 5, 9, 10, 12.5,
20, 25 and 100 kHz tuning steps are available.
• 1 MHz quick tuning step is only available in AM, FM
and WFM modes.
➥ While programmable tuning steps are OFF, turns
the 1 Hz step ON and OFF when pushed and
held for 1 sec.
• 1 and 10 Hz steps are only available in SSB, CW and
RTTY modes.
• 1 Hz indication appears, and the frequency can be
changed in 1 Hz steps.
➥ While the programmable tuning step is ON, enters the tuning step selection mode when pushed
and held for 1 sec.
@0 NOISE BLANKER KEY [NB/ADJ] (p. 78)
➥ Push momentarily to turn the noise blanker ON
and OFF. The noise blanker reduces pulse-type
noise such as that generated by automobile ignition systems. This function does not work on nonpulse noise or in WFM mode.
•“
The attenuator prevents a strong undesired signal near the
desired frequency or near your location, such as from a
broadcast station, from causing distortion or spurious signals.
@4 MODE KEY [MODE] (p. 34)
➥ Push momentarily to cycle through the operating
modes:
USB/LSB ➧ CW/CW-R ➧
RTTY/RTTY-R ➧ AM/FM/WFM
➥ Push and hold for 1 sec. to toggle the following
operating modes:
USB ↔ LSB
CW ↔ CW-R
RTTY ↔ RTTY-R
AM
→ FM
→ WFM
→ AM, etc
OPERATING MODE SELECTION
” appears when the noise blanker is ON.
➥ Push and hold for 1 sec. to enter the noise
blanker set mode.
@1 NOISE REDUCTION KEY [NR/LEV] (p. 79)
➥ Push momentarily to turn DSP noise reduction
ON and OFF.
AM
USB
LSB
CW
CW-R
RTTY
RTTY-R
FM
Push
momentarily
Push and hold
WFM
for 1 sec.
•“
” appears on the display when the function is activated.
➥ Push and hold for 1 sec. to enter the DSP noise
reduction level.
See the illustration of the Front panel on page i-2.
4
1
PANEL DESCRIPTION
■ Multi-function keys
D Menu M-2 functions
D Menu M-1 functions
SPL
A/B
FIL
XFC
F-1
F-2
F-3
F-4
SPLIT OPERATION
➥ Push momentarily to toggle the split function ON and OFF. (p. 89)
SPL
F-1
•“
” and transmit frequency appear when
the split function is ON.
➥ Push and hold for 1 sec. to turn the quick
split function ON. (p. 90)
• The offset frequency must be programmed in
advance using the miscellaneous (others) set
mode. (pgs. 129, 130)
• The offset frequency is the shift from the displayed frequency.
• The quick split function can be turned OFF in
the miscellaneous (others) set mode. (p. 129)
VFO A/B SELECTION
➥ Push momentarily to exchange the transmit VFO and receive VFO contents. (p.
F-2
27)
➥ Push momentarily to toggle the transmission VFO and reception VFO during split
operation. (p. 89)
➥ Push momentarily to toggle the transmit
and receive frequencies (and modes) of
memory channels when the split function
is turned ON.
➥ Push and hold for 1 sec. to equalize the
frequency and operating mode of the two
VFO’s.
A/B
• The lower indicated frequency and operating
mode are equalized to the upper (indicated)
VFO frequency and operating mode.
FILTER SELECTION (p. 75)
➥ Push momentarily to select one of three
IF filter settings.
F-3
➥ Push and hold for 1 sec. to enter the filter
set mode.
FIL
TRANSMIT FREQUENCY CHECK (pgs. 65, 89)
Monitors the transmit frequency when
pushed and held.
XFC
F-4
• While pushing and holding this key, the transmit frequency can be changed with [DIAL].
MEM
MW
MCL
V/M
F-1
F-2
F-3
F-4
MEMORY MENU (p. 103)
Push momentarily to indicate the memory
frequency and modes.
MEM
F-1
• Memory list indication is available.
MEMORY WRITE (pgs. 101, 102)
Push and hold for 1 sec. to store the selected frequency and operating mode into
F-2
the displayed memory channel.
MW
MEMORY CLEAR (p. 106)
Push and hold for 1 sec. to clear the selected memory channel contents.
MCL
F-3
•“
VFO/MEMORY SELECTION
➥ Push momentarily to toggle VFO and
memory modes. (pgs. 27, 100)
F-4
➥ Push and hold for 1 sec. to transfer the
selected memory channel to the currently
displayed VFO. (p. 107)
V/M
D Menu M-3 functions
DURING SSB OPERATION:
VOX
COM
AGC
TBW
F-1
F-2
F-3
F-4
DURING CW OPERATION:
BRK
1/4
AGC
F-1
F-2
F-3
F-4
DURING RTTY OPERATION:
F-1
1/4
AGC
F-2
F-3
F-4
DURING AM OPERATION:
VOX
F-1
5
” appears.
AGC
F-2
F-3
F-4
PANEL DESCRIPTION
DURING FM/WFM OPERATIONS:
VOX
DUP
TON
9600
F-1
F-2
F-3
F-4
BREAK-IN FUNCTION (p. 85)
➥ Push momentarily to select semi break-in,
full break-in (QSK) and break-in OFF.
BRK
F-1
VOX FUNCTION (p. 83)
➥ Push momentarily to toggle the VOX function ON and OFF.
VOX
F-1
• The VOX gain, ANTI-VOX and VOX delay
can be set in VOX set mode.
✔ What is the VOX function?
The VOX function (voice operated transmission) activates
the transmitter when you speak into the microphone and automatically returns to receive when you stop speaking.
SPEECH COMPRESSOR (p. 87)
➥ Push momentarily to toggle the speech
compressor ON and OFF.
•“
” or “
” appears when selecting
semi break-in or full break-in, respectively.
• An external switch, such as a foot switch,
must be connected to the ACC socket (pin 3,
pin 7 or RTTY SEND—see p. 23) if break-in
is turned OFF.
➥ Push and hold for 1 sec. to enter the
break-in delay time set mode.
•“
” appears when the VOX function is
ON.
➥ Push and hold for 1 sec. to enter the VOX
set mode.
✔ What is the break-in function?
•“
” appears when the speech compressor is ON.
➥ Push and hold for 1 sec. to enter the compression level set mode.
• Speech compression can be adjusted in
compression level set mode.
AGC (p. 74)
➥ Push to change the time constant of the
AGC circuit.
AGC
F-3
•“
,” “
” or “
” appears when
the fast time constant, middle time constant
or slow time constant is selected, respectively.
1/4 FUNCTION
Push to toggle the 1/4-speed tuning function ON and OFF in CW and RTTY
F-2
modes.
1/4
• When the 1⁄4 function is ON, “
and fine tuning can be used.
DUP
FM TONE OPERATION
➥ Push momentarily to set the subaudible
tone encoder for repeater use, tone
F-3
squelch function, DTCS and OFF.
TON
•“
” appears when the repeater tone
function is ON. (p. 63)
•“
” appears when the tone squelch function is ON. (p. 60)
•“
” appears when the DTCS squelch
function is ON. (p. 61)
” (OFF) can be selected.
➥ Push and hold for 1 sec. to enter the tone
frequency or DTCS code set mode. (pgs.
60, 61)
TBW (p. 84)
➥ Push momentarily to indicate the selected
TX filter width.
TBW
F-4
• Tone scan function is also available. (p. 62)
➥ Push and hold to transmit a 1750 Hz tone
when pushing and holding [PTT]. (p. 67)
• The popup indicator appears.
➥ Push and hold for 1 sec. to toggle the TX
filter width between narrow, middle or
wide.
• The following filters are specified as the default. Each filter width can be set in the quick
set mode. (pgs. 121, 122)
WIDE : 100 Hz to 2900 Hz
MID
: 300 Hz to 2700 Hz
NAR
: 500 Hz to 2500 Hz
” appears
DUPLEX FUNCTION (p. 63)
➥ Push to select the duplex transmit offset
direction or turn the function OFF.
F-2
➥ Push and hold for 1 sec. to turn the onetouch repeater function ON/OFF.
➥ Push and hold for 1 sec. to enter the AGC
set mode.
•“
1
Full break-in (QSK) activates the receiver between transmitted dots and dashes. This is useful when operating in nets,
or during DX pile-ups and during contests, when “fast responses” are common.
COM
F-2
1
9600 MODE
9600
Push to turn the 9600 bps data transmission mode ON and OFF. (p. 116)
F-4
6
1
PANEL DESCRIPTION
D Menu S-1 functions
DTM
DURING SSB/AM OPERATION:
VO
F-1
MET
VSC
F-3
F-4
F-2
DTMF OPERATION
Push to enter DTMF memory mode.
(p. 67)
F-4
• The DTMF send menu or DTMF root menu
DTMF 1st
appears depending on the “D
Menu” setting in the miscellaneous (others)
set mode. (p. 134)
DURING CW OPERATION:
VO
KEY
MET
VSC
F-1
F-2
F-3
F-4
DURING RTTY OPERATION:
VO
DEC
MET
VSC
F-1
F-2
F-3
F-4
DURING FM/WFM OPERATIONS:
VO
DTM
MET
VSC
F-1
F-2
F-3
F-4
D Menu S-2 functions
DURING VFO MODE:
SCN
PRI
V/M
VSC
F-1
F-2
F-3
F-4
DURING MEMORY MODE:
SCN
SEL
V/M
VSC
F-1
F-2
F-3
F-4
SCAN (pgs. 111–113)
➥ Push momentarily to start or stop the
scan function.
SCN
VO (p. 93)
VO
F-1
F-1
Push to enter the voice recorder mode.
• The voice TX/RX menu or voice root menu
VOICE 1st
appears depending on the “V
Menu” setting in the miscellaneous (others)
set mode. (p. 134)
PRIORITY WATCH (p. 113)
Push to start or stop priority watch.
PRI
F-2
METER SELECTION (p. 36)
Push to select the type of metering displayed (during transmit) on the display.
MET
F-3
• Power, SWR, ALC or COMP metering can be
selected.
• Only the S-meter is available during receive.
VOICE SQUELCH CONTROL (p. 82)
Push to toggle the voice squelch control
function ON and OFF.
VSC
F-4
VFO/MEMORY SELECTION
➥ Push momentarily to toggle VFO and
memory modes. (pgs. 27, 100)
F-3
➥ Push and hold for 1 sec. to transfer the
frequency and operating mode in the selected memory channel to the currently
displayed VFO. (p. 107)
V/M
VOICE SQUELCH CONTROL (p. 82)
Push to toggle the voice squelch control
function ON and OFF.
VSC
KEYER OPERATION (p. 45)
Push to enter the memory keyer mode.
KEY
F-2
• The keyer send menu or keyer root menu apKEYER 1st
pears depending on the “K
Menu” setting in the miscellaneous (others)
set mode.(p. 134)
RTTY DECODER FUNCTION (p. 54)
Push to toggle the RTTY decoder display
ON and OFF.
DEC
F-2
7
• RTTY decoder screen appears.
F-4
SELECT SCAN
➥ Push momentarily to toggle the select
scan settings ON and OFF for the seF-2
lected memory channel. (pgs. 104, 113)
➥ Push and hold for 2 sec. to clear all select
scan setting. (p. 113)
➥ While scanning, push to toggle the selected memory scan ON and OFF.
(p. 113)
SEL
PANEL DESCRIPTION
D Menu S-3 functions
1
D Menu G-1 (Scope) functions
MW
MPW
MPR
F-1
F-2
F-3
SPN
HLD
FIX
SPD
F-1
F-2
F-3
F-4
F-4
MEMORY WRITE (pgs. 101, 102)
Push and hold for 1 sec. to store the displayed VFO frequency and operating
F-1
mode into the selected memory channel.
MW
MEMO PAD WRITE (p. 109)
Push to store the displayed VFO frequency and operating mode into a memo
F-2
pad.
MPW
SWEEP STEPS (pgs. 70, 71)
➥ Push momentarily to change the sweep
step size.
SPN
F-1
➥ Push and hold for 1 sec. to change the
sweep steps to ±10 kHz.
1
PEAK HOLD (pgs. 70, 71)
➥ Push to freeze the current simple band
scope display.
HLD
F-2
MEMO PAD READ (p. 110)
Push to call up a memo pad.
• “H” indicator appears while the function is in
use.
➥ Push and hold for 1 sec. to clear the peak
levels.
MPR
• Peak levels are displayed in the background
on the simple band scope display. The peak
hold function can be disabled in the scope
set mode. (p. 71)
F-3
✔ What is the memo pad function?
The memo pad function stores the frequency and operating
mode for easy recall. The memo pads are separate from the
usual memory channels. The default number of memo pads
is 5, however, this can be increased to 10 in the miscellaneous (others) set mode, if desired. (p. 132)
• Available steps are ±10, 25, 50, 100 and 250
kHz.
FIX/CENTER SELECTION (pgs. 70, 71)
➥ Push to toggle the simple band scope fix
mode and center mode.
FIX
F-3
• Fix mode:
Rotating [DIAL] leaves the marker centered.
• Center mode:
Rotating [DIAL] moves the edge frequencies.
➥ During fix mode operation, push and hold
for 1 sec. to set the displayed frequency
to that of the marker.
SWEEP SPEED
➥ Push momentarily to change the sweep
speed between Fast and Slow. (pgs. 70,
F-4
71)
➥ Push and hold for 1 sec. to enter the
scope set mode. (p. 71)
SPD
8
1
PANEL DESCRIPTION
See the illustration of the HM-151 on page i-2.
■ Microphone (HM-151)
z SPCH/LOCK KEY [SPCH/LOCK]
➥ Push momentarily to have the frequency, etc. announced by the speech synthesizer. (p. 34)
• The parameters to be announced can be selected in
the miscellaneous (others) set mode. (p. 132)
➥ Push and hold for 1 sec. to toggle the microphone
lock function ON and OFF. (p. 37)
x PTT SWITCH [PTT] (p. 37)
Push and hold to transmit; release to receive.
Y]/[Z
Z]
c UP/DOWN SWITCHES [Y
Change the operating frequency.
• Push and hold to change the frequency repeatedly.
• Tuning step size is 50 Hz if no TS indicator is displayed.
v TRANSMIT INDICATOR (p. 37)
Lights red while transmitting.
b KEYPAD
➥ Pushing a key selects the operating band.
• [(GENE)•] selects the general coverage band.
➥ Pushing the same key 2 or 3 times calls up other
stacked frequencies in the band. (p. 28)
• Icom’s triple band stacking register memorizes 3 frequencies in each band.
• The functions can be assigned in the miscellaneous (others) set mode (p. 133). The default settings for [F-1] and
[F-2] are “MPW” and “MPR,” respectively.
Default settings
[F-1] (MPW): Push to store the selected readout
frequency and operating mode into
a memo pad.
[F-2] (MPR): Push to call up a memo pad.
⁄0 MEMORY WRITE [MW] (pgs. 101, 102)
Push and hold for 1 sec. to store the displayed VFO
frequency and operating mode into the displayed
memory channel.
⁄1 VFO/MEMORY SELECTION [V/M]
➥ Push momentarily to toggle VFO and memory
modes. (pgs. 27, 100)
➥ Push and hold for 1 sec. to transfer the selected
memory channel to the currently displayed VFO.
(p. 107)
➥ After pushing [(F-INP)ENT], enter a numeric frequency, followed by pressing [(F-INP)ENT]
again. (p. 29)
⁄2 TRANSMIT FREQUENCY CHECK [XFC]
(pgs. 65, 89)
Monitors the transmit frequency when pushed and
held.
• e.g. to enter 14.195 MHz, push [(F-INP)ENT] [1] [4]
[•] [1] [9] [5] [(F-INP)ENT].
• While pushing and holding this key, the transmit frequency can be changed with [DIAL].
n FILTER SELECTION [FIL]
➥ Push momentarily to select one of three IF filter
settings. (p. 75)
➥ Push and hold for 1 sec. to enter the filter set
mode. (p. 76)
⁄3 TUNER/CALL KEY [TUNER/CALL]
➥ During HF/50 MHz operation (p. 114):
● Push momentarily to toggle the automatic antenna tuner function ON and OFF.
m MODE KEY [MODE] (p. 34)
➥ Push momentarily to cycle through the operating
modes:
USB/LSB ➧ CW/CW-R ➧
RTTY/RTTY-R ➧ AM/FM/WFM
➥ Push and hold for 1 sec. to toggle the following
operating modes:
USB ↔ LSB
CW ↔ CW-R
RTTY ↔ RTTY-R
AM
→ FM
→ WFM
→ AM, etc
● Push and hold for 2 sec. to manually tune the
antenna.
, POWER INDICATOR
Lights green while transceiver power is ON.
9
. PROGRAMMABLE FUNCTION KEYS [F-1]/[F-2]
Program and perform a selected function.
• An optional antenna tuner must be connected.
•“
” indicator appears when the tuner is ON.
• An optional antenna tuner must be connected.
•“
” indicator appears when the tuner is ON.
➥ During 144/430 MHz operation (p. 100):
Push momentarily to select the call channel (or
return to the previous channel/frequency when
the call channel is already selected).
• “C1” is the 144 MHz call channel and “C2” is the 430
MHz call channel.
PANEL DESCRIPTION
1
D Microphone connector
MICROPHONE CONNECTOR INFORMATION
Rear panel view
CAUTION: DO NOT short pin 1 to ground as
this can damage the internal 8 V regulator.
1
87654321
HM-151
q +8 V DC output
w Frequency up/down
e M8V SW
r PTT
t GND (Microphone ground)
y Microphone input
u GND
i DATA IN
HM-103
q +8 V DC output
w Frequency up/down
e M8V SW
r PTT
t GND (Microphone ground)
y Microphone input
u GND
i Squelch switch
• When HM-151 is connected
PIN NO.
FUNCTION
DESCRIPTION
+8 V DC output
Max. 10 mA
Frequency up
Ground
Frequency down
Ground through 470 Ω
3
HM-151 connection
Grounded to indicate HM151 is connected.
8
HM-151 data
Control signal input
1
2
• When HM-103 is connected
PIN NO.
1
2
3
8
FUNCTION
DESCRIPTION
+8 V DC output
Max. 10 mA
Frequency up
Ground
Frequency down
Ground through 470 Ω
HM-151 connection
Open
Squelch open
“LOW” level
Squelch closed
“HIGH” level
R NEVER connect or use the supplied HM-151 (microphone) with other transceiver. This could cause damage to
the transceiver. The HM-151 is designed for use with the IC7000 ONLY.
10
1
PANEL DESCRIPTION
■ Rear panel
q
w
e
KEY
ACC
DATA
rt
y
ui o
MIC
GND
!0
ANT2
ANT1
DC 13.8V
!2
q ELECTRONIC KEYER JACK [KEY] (p. 22)
Accepts a paddle to activate the internal electronic
keyer.
u RTTY JACK [RTT Y] (p. 23)
Connects an external terminal unit for RTTY (FSK)
operation.
• Selection between the internal electronic keyer and
straight key operation can be made in the keyer set
mode. (p. 50)
• The keying polarity, mark/shift frequencies and etc. can
be selected in quick set mode (p. 123).
(⊕)
When connecting
a straight key
When connecting
a paddle
(dot)
(com)
(dash)
If you use an external electronic keyer, make sure
the output voltage of the keyer is less than 0.4 V
when keying the transmitter.
w ACCESSORY SOCKET [ACC] (p. 12)
Enables connection to external equipment such as a
TNC for data communications, a linear amplifier or
an automatic antenna selector/tuner, etc.
• See page at right for socket wiring information.
e DATA SOCKET [DATA] (p. 12)
6-pin mini-DIN socket to connect a TNC (Terminal
Node Controller), etc. for packet operation.
• See page at right for socket wiring information.
r VIDEO OUT JACK [VOUT] (p. 18)
Outputs a video signal.
t CI-V REMOTE CONTROL JACK [REMOTE]
(p. 142)
➥ Designed for use with a personal computer for remote control of the transceiver functions.
➥ Used for transceiver operation with another Icom
CI-V transceiver or receiver.
y TUNER CONTROL SOCKET [TUNER] (p. 20)
Accepts the control cable from an optional AH-4
HF/50 MHz AUTOMATIC ANTENNA TUNER.
11
!1
i EXTERNAL SPEAKER JACK [EXT SP] (p. 18)
Accepts a 4–8 Ω speaker.
o MICROPHONE CONNECTOR [MIC] (p. 17)
Accepts the supplied microphone (connected in parallel with the front panel’s [MIC] connector).
• See p. 3 for microphone notes.
• See p. 10 for microphone connector information.
!0 GROUND TERMINAL [GND] (p. 15)
Connect this terminal to a station or vehicle ground
to prevent electrical shocks, TVI, BCI and other
problems.
!1 ANTENNA CONNECTOR [ANT1], [ANT2] (p. 17)
Accepts a 50 Ω antenna with a PL-259 connector.
• [ANT1] is for connection to an HF/50 MHz antenna.
• [ANT2] is for connection to an 144/430 MHz antenna.
• ANT1 is used below and ANT2 above 60 MHz.
!2 DC POWER SOCKET [DC13.8V] (p. 19)
Accepts 13.8 V DC through the supplied DC power
cable.
Rear panel view
NOTE: DO NOT use a cigarette lighter socket as a
power source when operating in a vehicle. The plug
may cause voltage drops and ignition noise may be
superimposed onto transmit or receive audio.
PANEL DESCRIPTION
1
D DATA socket
DATA
1
PIN No.
NAME
1
DATA IN
2
GND
Common ground for DATA IN, DATA OUT and AF OUT.
3
PTT P
PTT terminal for packet operation. Connect to ground to activate the transmitter.
When grounded, microphone input (pin 6) of [MIC] connector will be disconnected.
2
3
4
5
4
6
5
Rear panel view
DESCRIPTION
Input terminal for data transmit. (1200 bps: AFSK/9600 bps: G3RUH, GMSK)
DATA OUT Data out terminal for 9600 bps operation only.
AF OUT
Data out terminal for 1200 bps operation only.
Squelch out terminal. This pin is grounded when the transceiver receives a signal
which opens the squelch.
6
SQL
• To avoid interfering transmissions, connect squelch to the TNC to inhibit transmission
when squelch is open.
• Keep RF gain at a normal level, otherwise a “SQL” signal will not be output.
1
D ACC socket
ACC
PIN No. NAME
1
2
3
13
9 10 11 12
5 6 7 8
1 2 3 4
Rear panel view
q brown
w red
e orange
r yellow
t green
y blue
u purple
i gray
o white
!0 black
!1 pink
!2 light
blue
!3 light
green
Color refers to
the cable strands
of the supplied
cable.
†
†
4
8V
DESCRIPTION
Regulated 8 V output.
GND Connects to ground.
Input/output pin.
HSEND (HF/50 MHz only)
Grounded when transmits.
BDT
Data line for the optional AT-180.
Output voltage
Output current
: 8 V ±0.3 V
: Less than 10 mA
———
Ground level
Output current
Input current (Tx)
: –0.5 V to 0.8 V
: Less than 20 mA
: Less than 200 mA
———
———
Output voltage
: 0 to 8.0 V
ALC voltage input.
Control voltage
Input impedance
: –4 V to 0 V
: More than 10 kΩ
7
Input/output pin.
VSEND (144/430 MHz only)
Grounded when transmits.
Ground level
Output current
Input current (Tx)
: –0.5 V to 0.8 V
: Less than 20 mA
: Less than 200 mA
8
13.8 V 13.8 V output when power is ON.
Output current
: Max. 1 A
9
TKEY Key line for the optional AT-180.
———
10
FSKK Controls RTTY keying
“High” level
“Low” level
Output current
: More than 2.4 V
: Less than 0.6 V
: Less than 2 mA
11
MOD Modulator input.
Input impedance
Input level
: 10 kΩ
: Approx. 100 mV rms
5
6
†
NC (*If the modification (p. 140) is
(BAND*) performed, band voltage output.)
SPECIFICATIONS
ALC
12
AF
13
SQLS
AF detector output.
Fixed level, regardless of [AF]
position indefault settings.
Output impedance : 4.7 kΩ
Output level
: 100–300 mV rms
Squelch output.
Grounded when squelch opens.
SQL open
SQL closed
: Less than 0.3 V/5 mA
: More than 6.0 V/100 µA
: Activating band can be changed in the miscellaneolus (other) set mode (p. 131).
12
1
PANEL DESCRIPTION
• When connecting the ACC conversion cable (OPC-599)
13
9 10 11 12
5 6 7 8
1 2 3 4
Connect to ACC socket
ACC 1
4
1
ACC 2
2
5
4
3
8
6
1
6
7
q FSKK
w GND
e HSEND
r MOD
t AF
y SQLS
u 13.8 V
i ALC
2
5
3
7
q8V
t ALC
w GND
y VSEND
u 13.8 V
e HSEND
r NC (BAND*)
* See p. 140 for details
■ Function display
!4
!3 !2 !1
q
w
e
!0
@4
o
i
u
y
t
r
q FREQUENCY READOUT
Shows the operating frequency.
w METER READOUTS
➥ Shows received signal strength while receiving.
➥ Shows either transmit power meter (Po), SWR,
ALC or compression level meter (COM) while
transmitting.
e MULTI-FUNCTION KEY GUIDE (p. 151)
Indicates the function of the multi-function keys.
These alphanumeric readouts show a variety of information such as current functions of the “F” keys
[F-1] to [F-4].
13
!5a
!6
!7
@3
@2
!5b
@1
@0
!9
!8
y MEMORY CHANNEL READOUT (p. 100)
Shows the selected memory channel or scan edge
channel.
• Memory bank indicator (A to E) appears to the left of
memory channel.
• This indicator appears both in VFO and memory modes.
u VFO/MEMORY INDICATORS (pgs. 27, 100)
➥VFO A or B appears when VFO mode is selected;
MEMO appears when memory mode is selected.
i VOICE RECODER INDICATORS (p. 94)
REC appears when the digital voice recoder function is activated.
r SPLIT FREQUENCY READOUT (pgs. 89, 90)
Shows the transmit frequency during split operation.
o LOCK INDICATOR (p. 37)
Appears when the dial lock function is activated.
t BLANK MEMORY INDICATOR (p. 101)
Appears when the displayed memory channel is not
programmed (blank channel).
!0 DIRECT FREQUENCY ENTRY INDICATOR (p. 29)
Appears when the transceiver is ready for direct frequency entry.
• This indicator appears both in VFO and memory modes.
• This indicator appears when [(F-INP)ENT] key on the
HM-151 is pushed.
PANEL DESCRIPTION
!1 SPLIT INDICATOR (pgs. 89, 90)
Appears during split operation.
!2 IF FILTER INDICATOR (p. 75)
Shows the selected IF filter number.
1
!7 MULTI-FUNCTION SCREEN
Shows the screens for the multi-function meter, simple band scope, SWR meter, memory channel,
voice recorder, memory keyer, DTMF memory encoder, RTTY decoder, IF filter selection or popup indication, etc.
!3 PASSBAND WIDTH INDICATOR (p. 75, 77)
Graphically displays the passband width for twin
PBT operation and center frequency for IF shift operation.
!8 PRIORITY WATCH INDICATOR (p. 113)
Appears while priority scan is activated.
!4 MODE INDICATORS (p. 34)
Shows the selected operating mode.
!9 SELECT MEMORY CHANNEL INDICATOR
(p. 113)
Appears when select scan is enabled for the selected memory channel.
• “-R” appears when CW reverse or RTTY reverse mode
is selected.
!5 PROGRAMMABLE/1 MHz TUNING STEP
INDICATORS
➥ !5a appears when the 1 MHz quick tuning step is
selected. (p. 31)
➥ !5b appears when the programmable tuning step
is selected. (p. 30)
!6 FUNCTION INDICATORS
➥“
” appears when the VOX function is activated. (p. 83)
➥“
” appears when full break-in operation is selected and “
” appears when semi break-in
operation is selected. (p. 85)
➥“
” appears when the speech compressor is
activated. (p. 87)
➥“
,” “
,” “
” or “
” (OFF)
appears when the fast time constant, middle time
constant, slow time constant or AGC OFF is selected, respectively. (p. 74)
➥“
” appears when the VSC (Voice Squelch
Control) function is activated in phone (SSB, AM,
FM, WFM) modes. (p. 82)
➥“
” appears for negative offset and “
”
appears for positive offset during duplex operation. (p. 63)
➥“
” appears when the 9600 baud mode is activated for packet operation. (p. 116)
➥“
” appears when the preamp is ON,
“
” appears when the 12 dB attenuator is
ON. (p. 72)
➥“
” or “
” appears when the RIT or ∂TX
function is activated. (pgs. 73, 86)
➥“
” appears when the noise blanker is activated. (p. ∂TX
78)
RIT
➥“
” appears when DSP noise reduction is activated. (p. 79)
➥“
” appears when the manual notch function is
activated. (p. 81)
➥“
” appears when the automatic notch function
is activated. (p. 80)
@0 1/4 FUNCTION INDICATOR (p. 32)
Appears when the 1⁄4-speed tuning function is activated in CW and RTTY modes.
1
@1 EXTERNAL KEYPAD INDICATOR
Shows the memory keyer or voice memory channel
External
number. This indication appears when “E
Keyp ad (VOICE)” or “E
External Keypad
(KEYER)” in the miscellaneous (others) set mode
(p. 135) is set to ON, and which one is activated.
<Example>
•“
” appears when the memory keyer “M2” is transmitted.
•“
” appears when the voice memory “T1” is transmitted.
@2 CLOCK READOUT (p. 117)
Shows the current time.
• UTC time or local time can be selected.
@3 TONE INDICATOR (pgs. 60,, 61, 64)
Appears during FM tone operation.
•“
,” “
” or “
” appears when the repeater
tone, tone squelch, DTCS squelch are activated, respectively.
@4 TUNER INDICATOR (pgs. 114, 115)
Appears when the optional automatic antenna tuner
is activated.
• This indicator blinks while the tuner is tuning.
14
2
INSTALLATION AND CONNECTIONS
■ Unpacking
■ Antenna connection
After unpacking, immediately report any damage to the
delivering carrier or dealer. Keep the shipping cartons.
For radio communications the antenna is of critical importance for output power and sensitivity. Use wellmatched 50-ohm antennas and coaxial feedline. An
SWR (standing wave radio) of 1.5:1 or lower is recommended when transmitting.
For a description and a diagram of accessory equipment included with the IC-7000, see ‘Supplied accessories’ on p. i-1 of this manual.
CAUTION: Protect your transceiver from lightning
by using a lightning arrestor.
■ Selecting a location
Select a location for the transceiver that allows adequate air circulation, free from extreme heat, cold, or
vibrations, and away from TV sets, TV antenna elements, radios and other electromagnetic sources.
The base of the transceiver has an adjustable stand
for desktop use. Set the stand to one of two angles depending on your operating conditions. (see description
on right hand page)
PL-259 CONNECTOR INSTALLATION EXAMPLE
q
30 mm
Coupling ring
w
10 mm (soft solder)
10 mm
Soft
solder
1–2 mm
■ Grounding
To prevent electrical shock, television interference
(TVI), broadcast interference (BCI) and other problems, ground the transceiver through the GROUND
terminal on the rear panel.
e
minal to a gas pipe or electric conduit, since the
connection could cause an explosion or electric
shock.
15
Strip the cable as
shown at left. Soft
solder the center conductor.
solder solder
Slide the connector
body on and solder it.
r
For best results, connect a heavy gauge wire or strap
to a long, buried copper rod. Make the distance between the [GND] terminal and ground as short as possible.
R WARNING: NEVER connect the [GND] ter-
Slide the coupling ring
down. Strip the cable
jacket and soft solder.
Screw the coupling
ring onto the connector
body.
ANTENNA SWR
Each antenna is tuned for a specified frequency
range and SWR increases outside that range. When
the SWR is higher than approx. 2.0 : 1, the transceiver’s power drops to protect the final transistors.
In this case, an antenna tuner is used to match the
transceiver and antenna. Low SWR allows full power
for transmitting even when using the antenna tuner.
The IC-7000 has an SWR meter to monitor the antenna SWR continuously.
INSTALLATION AND CONNECTIONS
2
■ Installation
D Single body mounting
MB-62
(optional)
D Stand
Spring washer
Nut
To raise the stand:
With the transceiver upside down, pull the stand towards the rear panel and then upwards, as illustrated below.
Supplied with
the MB-62*
then up
Pull back
Flat washer
2
*CAUTION: Non-supplied screws (longer than 8 mm)
may damage the internal units.
D Front panel separation
q While pulling the front panel latch towards you,
slide the front panel to the left (fig. 1).
w Attach the optional OPC-1443 to the main body
and tighten the supplied screw as in fig. 2.
e Attach the other end of the OPC-1443 to the detached front panel as in fig. 3.
fig. 1
CAUTION: NEVER detach/attach the front panel
when connecting the DC power supply (or battery).
Be sure to disconnect the DC power cable from the
[13.8 V] socket on the transceiver rear panel.
fig. 2
fig. 3
To remove
Separation cable
(OPC-1443)
Latch
Separation cable
(OPC-1443)
D Front panel mounting
q Attach the MB-105 to a flat surface using the four
supplied screws (fig. 1).
w Fix the detached front panel to the MB-105 as illustrated in fig. 2.
BE CAREFUL to mount the MB-105 so that the
front panel attaches with the correct side up.
fig. 1
fig. 2
16
2
INSTALLATION AND CONNECTIONS
■ Required connections
MICROPHONE (p. 10)
GROUND (p. 15)
Use the heaviest
gauge wire or strap
available and make
the connection as
short as possible.
STRAIGHT KEY
HM-151
Grounding prevents
electrical shocks, TVI
and other problems.
RTTY TERMINAL
UNIT (p. 23)
KEY
ACC
MIC
DATA
GND
ANT2
ANT1
DC 13.8V
2 m/70 cm ANTENNA
DC POWER SUPPLY (p.19)
AC outlet
A DC power supply
13.8 V; at least 25 A
Red Black
+
_
17
HF/50 MHz ANTENNA
INSTALLATION AND CONNECTIONS
2
■ Advanced connections
HEADPHONES
2
OPC-589 (p. 150)
DATA SOCKET (p. 12)
6-pin mini DIN socket to
connect to a TNC, etc. for
packet operation.
or
SPEAKER
VIDEO OUT
to [VOUT] jack
SM-20
Vout GND
3.5(d) mm
DESKTOP (p. 149)
MICROPHONE
ACC SOCKET (p. 12)
KEY
ACC
Selectable with the
[PHONE/SPEAKER]
switch on the back of
the front panel.
MIC
DATA
GND
ANT2
ANT1
DC 13.8V
REMOTE (p. 142)
Used for computer control and transceive
operation.
EXTERNAL
SPEAKER (p. 149)
SP-7/SP-10
AH-4 (p. 20)
AH-2b
18
2
INSTALLATION AND CONNECTIONS
■ Power supply connections
Use the DC power supply with a 25 A capacity when
operating the transceiver with AC power. Refer to the
diagrams below.
CAUTION: Before connecting the DC power
cable, check the following important items. Make
sure:
• The [POWER] switch is OFF.
• Output voltage of the power source is 12–15 V.
• DC power cable polarity is correct.
Red
Black
: positive + terminal
: negative _ terminal
■ Connecting a DC power supply
AC outlet
A DC power supply
Transceiver
13.8 V; at least 25 A
Red Black
+
_
30 A fuses
AC cable
Supplied
DC power cable
DC power
socket
■ Battery connections
• DO NOT use a cigarette lighter socket as a power
source when operating in a vehicle. The plug may
cause voltage drops and ignition noise may be superimposed onto transmit or receive audio.
• Use a rubber grommet when passing the DC
power cable through a metal plate to prevent a
short circuit.
• RWARNING NEVER connect to a battery
without supplying a DC fuse, otherwise a fire
hazard occurs.
• NEVER connect the transceiver directly to a 24 V
battery.
CONNECTING A VEHICLE BATTERY
Note: Use terminals for
the cable connections.
Crimp
Grommet
red
black
12 V
battery
The transceiver may not receive well on some
frequencies when installed in a hybrid vehicle, or
any type of electric vehicle (fuel cell vehicle). This
is because vehicle’s electric components such as
the inverter system generate a lot of electric noise.
19
Solder
Supplied
DC power cable
IMPORTANT!
Detailed installation notes for Icom mobile transceivers to be fitted into vehicles are available. Contact your Icom dealer or distributor.
INSTALLATION AND CONNECTIONS
2
■ External antenna tuners
CONNECTING THE AH-4
Coaxial cable
IC-7000
ANT1
Long wire or optional AH-2b
(from the AH-4)
AH-4
Ground
Ground
2
CONNECTING THE AT-180
ACC cable supplied with the AT-180
HF
to 6 m
antenna
Coaxial cable supplied
with the AT-180
[ACC]
[ANT1]
[ANT]
AT-180
[ACC]
Either of the two
external connectors
IC-7000
Ground
Ground
[TRANSCEIVER]
• Turn the IC-7000’s power OFF when connecting
the AT-180, otherwise, the CPU may malfunction
and the AT-180 may not function properly.
• The OPC-742 is required when using both the AT180 and a 2m/70cm linear amplifier.
• Do not connect [ANT2] to the AT-180. When using
an HF to 2m/70cm dual or wide-band antenna,
use a duplexer between the AT-180 and antenna
since 2 m/70 cm signals do not pass through the
AT-180.
Transceiver
[ANT 1]
AT-180
HF to 2 m/70 cm
antenna
Duplexer
[ANT 2]
20
2
INSTALLATION AND CONNECTIONS
■ Linear amplifier connections
Use the [ANT1] connector when connecting an HF/50
MHz linear amplifier.
CONNECTING THE IC-PW1/EURO
Remote control cable (supplied with the IC-PW1/EURO)
To an
antenna ACC-1
7-pin side
ACC cable (supplied with the IC-PW1/EURO)
REMOTE
ANT
OPC-599 conversion cable
ACC
REMOTE
GND
INPUT1
EXCITER
1
1&2
ANT1
Transceiver
Coaxial cable
(supplied with the IC-PW1/EURO)
GND
Ground
IC-PW1/EURO
AC outlet
versions : 100–120/220–240 V
(Non-European
)
European version
: 230 V
CONNECTING A NON-ICOM LINEAR AMPLIFIER
R WARNING:
• Set the transceiver output power and linear amplifier ALC output level referring to the linear amplifier instruction manual. Be sure the linear amplifier keying circuit control voltage is compatible
with the IC-7000, before connecting to the
HSEND line (ACC cable).
• The ALC input level must be in the range 0 V to
–4 V, and the transceiver does not accept positive
voltage. Non-matched ALC and RF power settings
could cause a fire or damage the linear amplifier.
• The IC-7000 SEND line (ACC connector pin 3) is
rate at 16 V/200 mA DC. If this level is exceeded,
a larger external relay must be used.
50 Ω coaxial cable
To an
antenna
Transceiver
ANT1
GND
RF OUT
RF IN
ALC (Blue)
ALC
HSEND
(Orange)
KEY
ACC
Relay
13.8V (Gray)
21
ACC cable
Ground
INSTALLATION AND CONNECTIONS
2
■ Connections for CW
Keyer set mode (p. 49)
[KEY]
Rear panel
Keyer set mode setting
Paddle polarity
Keyer Type
Normal
ELEC-KEY
N o rma l
[ACC]
Paddle polarity
Keyer Type
13
9 10 11 12
5 6 7 8
1 2 3 4
For no break-in operation:
Connect an external switch
such as a foot switch; or use
the RTTY SEND terminal for
all bands. (See p. 23)
Reverse
ELEC-KEY
2
R e v e rs e
Paddle
Paddle polarity
Keyer Type
Normal
BUG-KEY
Bug
Paddle polarity
Keyer Type
Normal
Straight
Straight key
Paddle polarity
[MICROPHONE]
See p. 50 for connection details:
Paddle operation from [MIC]
connector.
Normal
Keyer Type
ELEC-KEY
MIC U/D keyer (HM-103)
ON
Microphone (HM-103)
22
2
INSTALLATION AND CONNECTIONS
■ Connections for RTTY
D Connections for RTTY (FSK)
Rear panel
[ACC]
[RTTY]
[EXT SP]
2-conductor 1/8˝ plug
TNC or PC interface
for the RTTY software
Personal computer
AF GND
SEND
FSKK
GND
3-conductor 1/8˝ plug (supplied)
Rear panel
view
SQL*1 (light green)
FSKK (black)
AF out (light blue)
MSEND*2
GND (red)
13
9 10 11 12
5 6 7 8
1 2 3 4
*1Connect SQL line when required.
*2eHF/50 MHz: orange
u144/430 MHz: purple
Colors refer to the wires in
the supplied ACC cable.
D Connections for RTTY (AFSK)
Rear panel
[ACC]
[MIC]
13
9 10 11 12
5 6 7 8
1 2 3 4
Rear panel
view
Rear panel
view
Personal computer
t GND
u GND
!2 AF out (light blue)
23
TNC or PC interface
for the RTTY software
r PTT
y MIC
i SQL*1
*1Connect SQL line when required.
Colors refer to the wires in
the supplied ACC cable.
INSTALLATION AND CONNECTIONS
2
■ Connections for packet, SSTV or PSK31
D When connecting to [DATA] socket
TX AUDIO
DATA IN q
w GND
GND
r DATA OUT
PTTP e
*1Connect SQL line when required.
1
y SQL*
SQL
RX AUDIO
PTT
t
AF OUT
[DATA]
(Rear panel)
RS-232C
2
TNC or
PC interface for the software
Personal computer
D When connecting to [ACC] socket
Rear panel
[ACC]
Rear panel
view
13
9 10 11 12
5 6 7 8
1 2 3 4
SQL*1 (light green)
AF in (pink)
AF out (light blue)
MSEND*2
GND (red)
TNC or
PC interface for the software
Personal computer
*1Connect SQL line when required.
*2eHF/50 MHz: orange
Colors refer to the wires in
u144/430 MHz: purple
the supplied ACC cable.
D When connecting to [MIC] connector
Rear panel
[ACC]
[MIC]
13
9 10 11 12
5 6 7 8
1 2 3 4
Rear panel
view
Rear panel
view
TNC or
PC interface for the software
Personal computer
t GND
u GND
!2 AF out (light blue)
r PTT
y MIC
i SQL*1
*1Connect SQL line when required.
Colors refer to the wires in
the supplied ACC cable.
24
3
BASIC OPERATION
■ When first applying power (CPU resetting)
Before first applying power, make sure all connections required for your system are complete by referring to Chapter 2. Then, reset the transceiver using
the following procedure.
[Y]
[PWR]
[Z]
Resetting CLEARS all programmed contents in
memory channels and returns default values in set
mode.
q Make sure the transceiver power is OFF.
Y(BAND)] and
w While pushing and holding [Y
Z(BAND)], push [PWR] to start resetting.
[Z
• The internal CPU is reset.
• The display changes to ‘ALL CLEAR,’ ‘RF power 100%’
and ‘Initial frequency and Mode’ as shown at right.
The transceiver’s
initial frequency and mode
M-1)
D Menu resetting (M
If you can’t figure out how to return to menu M-1:
Y (MENU/GRP)] or
While pushing and holding either [Y
Z (MENU/GRP)], turn power ON.
[Z
[PWR]
• The other groups are also reset to S-1 or G-1(Scope) at
this time.
[MENU/GRP]
■ Initial settings
After resetting the transceiver, set controls and
switches as shown in the diagram below.
CCW : counterclockwise
[RF/SQL]: Center
[AF]: Max. CCW
[POWER]: OFF
[PBT/M-ch/RIT]: PBT
(indicator lights)
[PBT]: Center
(Push and hold for 1 sec.)
[LOCK]: OFF
Turn power ON, then check the display. If any of the
following indicators appear, turn them OFF as follows:
• Tuning step indicators, Z, (SSB, CW or RTTY):
Push [TS].
• MHz tuning step indicator, Z, (FM, WFM or AM):
Push [TS]
• 1 Hz frequency readout (SSB, CW or RTTY):
Push and hold [TS].
• Preamp indicator,
:
Push [P.AMP/ATT]
• Attenuator indicator,
:
Push [P.AMP/ATT]
25
• Noise blanker indicator,
:
Push [NB/ADJ]
• Noise reduction indicator,
:
Push [NR/LEV]
• Manual notch indicator,
:
Push [MNF/ADJ]
• Auto notch indicator,
:
Push [ANF/• REC]
• Memory mode indicator, MEMO:
Use [F-4 V/M] in the M-2 menu (p. 27).
• Split indicator,
:
Use [F-1 SPL] in the M-1 menu (p. 89).
BASIC OPERATION
3
■ VFO description
VFO is an abbreviation of Variable Frequency Oscillator, and traditionally refers to an oscillator.
The IC-7000 VFO is somewhat different. The VFO display of the IC-7000 acts like a computer’s window and
can show one frequency and one operating mode.
Select
MODE
KEY
VFO
Change
You can call up a desired frequency to the VFO with
the memo pad-read key (p. 110) or the memory transfer function (p. 107). You can also change the frequency with [DIAL] and select an operating mode with
[MODE] key or call up previously accessed frequency
and modes with the band stacking register (p. 28).
DIAL
Transfer
BAND
21.295 MHz
The IC-7000 has two VFOs, specially suited for split
frequency operation. The VFOs are called VFO A and
VFO B. You can use the desired VFO to call up a frequency and operating mode for operation.
Transfer
MEMO PAD
28.025 MHz
Transfer
MEMORY
CHANNEL
3
7.001 MHz
D Differences between VFO and memory mode
VFO MODE
Each VFO shows a frequency and operating mode. If
the frequency or operating mode is changed, the VFO
automatically memorizes the new frequency or operating mode.
MEMORY MODE (pgs. 100–108)
Each memory channel shows a frequency and operating mode like a VFO. Even if the frequency or mode
is changed, the memory channel does not memorize
the new frequency or operating mode.
When VFO settings are changed with frequency and
mode from another VFO or memory mode, the lastused frequency and operating mode for that VFO appear.
When a memory channel is changed with frequency
and mode from another memory channel or VFO
mode, the memorized frequency and operating mode
appear.
[EXAMPLE]
[EXAMPLE]
VFO is selected.
Memory channel 1 is
selected.
The frequency is changed.
The frequency is changed.
Memory mode is selected.
Another memory channel
is selected.
VFO is selected again.
Memory channel 1 is
selected again.
Changed frequency (14.123 MHz) appears.
Changed frequency (14.123 MHz) does not appear and
memorized frequency (14.100 MHz) appears instead.
26
3
BASIC OPERATION
■ VFO operation
D Selecting VFO A/VFO B
q Select M-1.
Either “
” or “
” appears.
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: M-1, M-2 or M-3
Either
Y or Z
w Push [F-2 A/B] to toggle VFO A or VFO B.
[MENU/GRP] [F-2]
D VFO equalization
q Select M-1.
w Push and hold [F-2 A/B ] for 1 sec. to set the
undisplayed VFO frequency and mode to those of
the displayed VFO.
• Three beeps sound when the VFO equalization is completed.
CONVENIENT
Use two VFOs as a quick memory
When you find a new station, but you wish to continue
searching, the Two-VFO system can be used for quick
memory storage.
q Push [F-2 A/B ] for 1 sec. to store the displayed frequency into the undisplayed VFO.
w Continue searching for stations.
e Push [F-2 A/B] to retrieve the stored frequency.
r To continue searching for a station, push [F-2 A/B ]
again.
Push
then push
for 1 sec.,
again.
■ Selecting VFO/memory mode
q Select M-2.
w Push [F-4 V/M ] to toggle VFO and memory
modes.
“VFO” indicator
[MENU/GRP]
[F-4]
Memory channel
indicator
27
BASIC OPERATION
3
■ Selecting an operating band
The triple band stacking register provides 3 memories
in one band. 3 sets of frequency and operating mode
on each band are automatically stored when used.
HM-151
SPCH
/LOCK
1.8
10
21
50
1
4
7
.
TUNER
/CALL
3.5
14
24
2
5
8
144
0
XFC
V/M
MW
F-1
F-2
7
18
28
3
MODE
6
FIL
9
GENE
430
CE
If a band key (on the HM-151) is pushed once, the last
used frequency and operating mode on that band are
called up. When the key is pushed again, another
stored frequency and operating mode are called up.
Band keys
F-INP
ENT
This function is convenient when you operate 3 operating modes on one band. For example, one register
is used for a CW frequency, another for an SSB frequency and the other one for an RTTY frequency.
See the table below for a list of the bands available
and the default settings for each band.
3
BAND
REGISTER 1
REGISTER 2
1.8 MHz
3.5 MHz
7 MHz
10 MHz
14 MHz
18 MHz
21 MHz
24 MHz
28 MHz
50 MHz
144 MHz
430 MHz
General
1.900000 MHz CW
3.550000 MHz LSB
7.050000 MHz LSB
10.120000 MHz CW
14.100000 MHz USB
18.100000 MHz USB
21.200000 MHz USB
24.950000 MHz USB
28.500000 MHz USB
50.100000 MHz USB
145.000000 MHz FM
433.000000 MHz FM
15.000000 MHz USB
1.910000 MHz CW
3.560000 MHz LSB
7.060000 MHz LSB
10.130000 MHz CW
14.200000 MHz USB
18.130000 MHz USB
21.300000 MHz USB
24.980000 MHz USB
29.500000 MHz USB
50.200000 MHz USB
145.100000 MHz FM
433.100000 MHz FM
15.100000 MHz USB
REGISTER 3
1.915000 MHz CW
3.580000 MHz LSB
7.020000 MHz CW
10.140000 MHz CW
14.050000 MHz CW
18.150000 MHz USB
21.050000 MHz CW
24.900000 MHz CW
28.100000 MHz CW
51.000000 MHz FM
145.200000 MHz FM
433.200000 MHz FM
15.200000 MHz USB
D Using the band stacking registers
q Push [(14)5], then select a frequency and an operating mode.
[Example]: 14 MHz band
SPCH
/LOCK
1.8
10
21
50
1
4
7
.
3.5
14
24
TUNER
/CALL
2
5
8
144
0
V/M
MW
F-1
F-2
7
18
28
• Frequency and operating mode are memorized in the
first band stacking register.
XFC
3
MODE
6
FIL
GENE
9
430
CE
1.8
10
21
1
4
7
3.5
14
24
2
5
8
7
18
28
3
MODE
6
FIL
9
GENE
F-INP
ENT
50
HM-151
.
144
0
430
CE
F-INP
ENT
w Push [(14)5] again, then select another frequency
and operating mode.
• This frequency and operating mode are memorized in
the second band stacking register.
e Push [(14)5] again, then select another frequency
and operating mode.
• This frequency and operating mode are memorized in
the third band stacking register.
• When a fourth frequency and operating mode are selected on a band, the first register set in step q, is over
written.
28
3
BASIC OPERATION
■ Frequency setting
The transceiver has several tuning methods for convenient frequency tuning.
D Tuning with the main dial
[Y]
[Z]
Y(BAND)] or [Z
Z(BAND)] to select the desired
q Push [Y
band. Or push the desired band key on the microphone 1–3 times.
• Three different frequencies can be selected on each
band with the microphone’s band key. (See previous
page “Using the band stacking register.”)
[DIAL]
HM-151
SPCH
/LOCK
1.8
10
3.5
1
14
4
21
24
7
50
TUNER
/CALL
MW
F-1
F-2
7
2
28
8
144
.
3
18
5
MODE
6
FIL
9
GENE
430
0
w Rotate [DIAL] to set the desired frequency.
XFC
V/M
CE
Band keys
F-INP
ENT
If the dial lock function is activated, “
” indicator
lights, and [DIAL] does not function. In this case,
push [SPCH/LOCK] to deactivate the lock function. (p. 37)
D Direct frequency entry with the microphone’s keypad
The HM-151 has a keypad for direct frequency entry
as described right.
1.8
10
21
50
1
4
7
.
3.5
14
24
TUNER
/CALL
2
5
8
144
0
XFC
MW
F-1
F-2
7
28
3
MODE
6
FIL
9
430
CE
” appears.
• Push [(50)•] to input “ • (decimal point)” between the
MHz digits and kHz digits.
V/M
18
•“
w Input the desired frequency.
HM-151
SPCH
/LOCK
q Push [F-INP/ENT].
e Push [F-INP/ENT] to set the input frequency.
• To cancel the input, push [CE] instead of [F-INP/ENT].
[EXAMPLES]
14.025 MHz
GENE
F-INP
ENT
Keypad
F-INP
ENT
1.8
1
10
4
50
.
144
50
.
144
0
3.5
2
14
5
F-INP
ENT
18.0725 MHz
F-INP
ENT
1.8
24
8
F-INP
ENT
706 kHz
29
1
144
0
50
5.100 MHz
F-INP
ENT
14
7.000 MHz
F-INP
ENT
21
21.280
F-INP
ENT
50
21.245
0
.
5
7
.
21
21
50
7
7
.
3.5
144
1.8
2
0
1
14
18
5
F-INP
ENT
6
F-INP
ENT
F-INP
ENT
F-INP
ENT
3.5
2
10
4
14
5
F-INP
ENT
BASIC OPERATION
3
D Programmable tuning step
The operating frequency can be changed in steps of
(0.01 (AM/FM/WFM only), 0.1, 1, 5, 9, 10, 12.5, 20,
25 or 100 kHz selectable) for quick tuning.
Appears
[TS] [DIAL]
q Push [TS] momentarily to turn the programmable
tuning function ON.
• “Z” appears when the programmable tuning function is
ON.
Programmable tuning step indicator
w Rotate [DIAL] to change the frequency in programmed kHz steps.
e Push [TS] again to turn the programmable tuning
function OFF.
• “Z” disappears.
r Rotate [DIAL] for normal tuning, if desired.
3
D Selecting “kHz” step
Programmable tuning steps are available to suit your
operating requirements.
These tuning steps are:
• Independently selectable for each mode
• Selectable from 0.01 (AM/FM/WFM only), 0.1, 1, 5,
9, 10, 12.5, 20, 25 and 100 kHz
q Push [TS] momentarily to turn the programmable
tuning step ON.
• “Z” appears when the programmable tuning function is
ON.
w Push and hold [TS] for 1 sec. to enter the tuning
step setting display.
• The tuning step setting for the selected mode appears.
[MODE]
[TS] [DIAL]
Appears
e Select the desired operating mode with [MODE].
(see p. 34)
r Rotate [DIAL] to select the desired tuning step
from 0.01 (FM/WFM/AM only), 0.1, 1, 5, 9, 10,
12.5, 20, 25 or 100 kHz.
• Push and hold [F-4 DEF] for 1 sec. to return to the default setting, if desired.
t Repeat steps e and r to select the “kHz” tuning
steps for other modes, if desired.
Z(MENU/GRP)]) to exit the setting
y Push [TS] (or [Z
display.
30
3
BASIC OPERATION
D Selecting 1 Hz or 10 Hz step (SSB/CW/RTTY only)
When neither the quick tuning step or programmable
tuning step “Z” appear, rotating [DIAL] changes the
frequency in increments of 1 or 10 Hz. These tuning
steps are only available in SSB, CW and RTTY
modes.
[MODE]
[TS] [DIAL]
q Select SSB, CW or RTTY mode if necessary.
w Push and hold [TS] for 1 sec. to toggle between
the 1 Hz and 10 Hz step settings.
• When the 1 Hz step is selected, the 1 Hz digit appears
in the frequency indication; when the 10 Hz step is selected, the 1 Hz digit disappears from the frequency indication.
• Rotating [DIAL] changes the frequency in 1 Hz or 10Hz
tuning step.
Rotating [DIAL] changes the
frequency in 10 Hz steps.
Push and hold
for 1 sec.
Rotating [DIAL] changes the
frequency in 1 Hz steps.
D 1 MHz quick tuning step (FM/WFM/AM only)
The quick tuning step function allows you to change
the frequency in 1 MHz steps when rotating [DIAL].
This function is only available in FM, WFM and AM
modes.
[MODE]
Appears
[TS] [DIAL]
q Select FM, WFM or AM mode if necessary.
w Push [TS] momentarily to toggle between the 1
MHz tuning step and the programmable tuning
step.
• “Z” appears above the 1 MHz indicator when the 1
MHz tuning step is selected.
• Rotating [DIAL] changes the frequency 1 MHz.
Quick tuning step indicator
Rotating [DIAL]
changes the frequency
in 1 MHz steps.
31
BASIC OPERATION
3
• [TS] switch flow chart
SSB/CW/RTTY modes
Push
Any mode
Push
FM/WFM/AM modes
Appears
momentarily
momentarily
Programmable step tuning
SSB/CW/RTTY modes (0.1 kHz –100 kHz)
FM/WFM/AM modes (0.01 kHz–100 kHz)
10 Hz tuning
Push
Appears
1 sec.
1 sec.
Push
1 MHz tuning
1 sec.
momentarily
3
1 Hz tuning
Appears
Selectable for each mode.
D 1⁄4 tuning function (CW/RTTY only)
While operating in CW/RTTY, the 1⁄4 tuning function is
available for critical tuning. Dial sensitivity is reduced
to 1⁄4 of normal when the 1⁄4 function is in use.
q Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
w Push [F-2 1/4] to toggle the 1⁄4 function ON and
OFF.
• “ ” indication appears when the function is in
use.
Appears
[MENU/GRP] [F-2]
NOTE: This function is only available when the programmable tuning step is OFF (p. 30).
32
3
BASIC OPERATION
D Auto tuning step function
When rotating the tuning dial rapidly, the tuning speed
accelerates automatically as selected.
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-4 OTH] to enter the miscellaneous (others) set mode.
MAIN DIAL
e Push [F-1 ≤] or [F-2 ≥] to select “M
Auto TS.”
r Rotate [DIAL] to select the desired tuning speed
from high, low and OFF.
[AF]
[MENU/GRP] [F-1] [F-2] [F-4]
• HIGH: Approx. 5 times faster
• LOW : Approx. twice faster
• OFF : Auto tuning step is turned OFF
• Push [F-4 DEF] for 1 sec. to return to default setting.
Z(MENU/GRP)] twice to return to the normal
t Push [Z
operating mode.
D Band edge warning beep
When selecting a frequency that lies outside of a
band’s specified frequency range, a warning beep
sounds.
This function can be turned OFF in set mode, if desired.
q Enter the miscellaneous (others) set mode as
above.
Beep (Band
w Push [F-1 ≤] or [F-2 ≥] to select “B
Edge),” then rotate [DIAL] to select the desired
setting.
• Push [F-4 DEF] for 1 sec. to return to default setting.
Z(MENU/GRP)] twice to return the normal ope Push [Z
erating mode.
■ Volume setting
Rotate [AF] control clockwise to increase; counterclockwise to decrease the audio output level.
• Set a suitable audio level.
Audio output
increases
Audio outut
decreases
33
[AF]
[DIAL]
BASIC OPERATION
3
■ Operating mode selection
The following modes are available in the IC-7000:
SSB (LSB/USB), CW, CW-R (CW reverse), RTTY,
RTTY-R (RTTY reverse), AM, FM and WFM (receive
only).
OPERATING MODE SELECTION
To select the desired mode of operation, push
[MODE] one or more times, then push [MODE] for
1 sec., if necessary. See the diagram at right for the
order of selection.
Push
USB
LSB
CW
CW-R
RTTY
RTTY-R
momentarily
Push and hold
• The selected mode is indicated in the function display.
[MODE]
AM
FM
WFM
for 1 sec.
3
SPCH
/LOCK
NOTE: If a desired mode cannot be selected, it
may be hidden because of a setting in the miscellaneous (others) set mode (pgs. 134, 135).
1.8
10
21
50
1
4
7
.
3.5
14
24
TUNER
/CALL
2
5
8
144
0
XFC
V/M
MW
F-1
F-2
7
18
28
3
MODE
6
FIL
9
430
CE
MODE
GENE
F-INP
ENT
HM-151
■ Voice synthesizer function
The IC-7000 has a voice synthesizer function. This
function announces the S-meter level, operating frequency and mode (S-meter level’s announcement
can be deactivated—p. 132) in a clear, electronically
generated voice, in English (or Japanese).
q Select the desired parameters to be announced,
such as Audio level, speed, language, contents, in
the miscellaneous (others) set mode. (p. 131)
w Push [SPCH/LOCK] momentarily to announce the
selected contents.
[SPCH/LOCK]
• Push [SPCH/LOCK] momentarily to stop the announcement.
34
3
BASIC OPERATION
■ Squelch and receive (RF) sensitivity
[RF/SQL] adjusts the RF gain and squelch threshold
level. The squelch removes noise output from the
speaker (closed position) when no signal is received.
[RF/SQL]
• The squelch is particularly effective for FM. It is also available for other modes.
• The 12 to 1 o’clock position is recommended for any setting of the [RF/SQL] control.
• The control can be set as ‘Auto’ (RF gain control in SSB,
CW and RTTY; squelch control in AM, FM and WFM (RF
gain is fixed at maximum) in the miscellaneous (others)
set mode as follows (p. 129).
SETTING
OPERATION
RF+SQL
(default)
Can be used in all modes.
Functions as noise squelch or S-meter
squelch in FM mode; S-meter squelch
only in other modes.
SQL
Operates as a squelch control.
Noise squelch (FM mode)
Recommended level
Squelch is
open.
Maximum
RF gain
• RF gain is fixed at maximum sensitivity.
Operates as an RF gain control in
SSB, CW and RTTY modes.
AUTO
• When functioning as RF gain/squelch control
• Squelch is fixed open.
Operates as a squelch control in AM,
FM and WFM modes.
RF gain
adjustable
range
S-meter shows
squelch level
• RF gain is fixed at maximum sensitivity.
• When functioning as RF gain control
(Squelch is fixed open; SSB, CW, RTTY only)
Adjusting RF gain (Receive sensitivity)
Normally, [RF/SQL] is set to the 11 o’clock position.
Rotate [RF/SQL] to the 11 o’clock position for maximum sensitivity.
• Rotating counterclockwise from the maximum position reduces sensitivity.
• The S-meter indicates receive sensitivity.
Adjustable
range
Minimum RF gain
Maximum RF gain
• When functioning as squelch control (RF gain is
fixed at maximum)
Adjusting squelch (Removing non-signal noise)
Rotate [RF/SQL] clockwise when receiving no signal,
until the noise just disappears.
• [RX] indicator light goes out.
• Rotating [RF/SQL] past the threshold point invokes the Smeter squelch—this allows you to set a minimum signal
level needed to open the squelch.
Noise squelch (FM mode)
Noise squelch
threshold
(FM mode)
Squelch is
open.
Lowest threshold
S-meter squelch
threshold
S-meter
squelch
Highest threshold
While rotating the RF gain control, noise may be
heard. This comes from the DSP unit and does not
indicate an equipment malfunction.
35
BASIC OPERATION
3
■ Meter function
The transceiver has 4 transmit meter functions for
your convenience. Select the desired meter with the
[F-3 MET] in the S-1 display.
DISPLAY
INDICATION
[MENU/GRP]
Po
Indicates the relative RF output power in %.
SWR
Indicates the SWR on the transmission
line.
ALC
Indicates the ALC level. When the meter
movement shows the input signal level exceeds the allowable level, the ALC limits
the RF power. In such cases, reduce the
MIC gain setting (see p. 38) in the quick
set mode.
COM
Indicates the compression level when the
speech compressor is in use.
[F-3]
q Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
MEASUREMENT
3
w Push [F-3 MET] one or more times to select from
RF power (Po), SWR, ALC or compression level
(COM).
• The display indication changes as the table at the right.
D Multi-function meter
In addition, the transceiver can display the multi-function meter in the graphic display, which displays all
transmit meters simultaneously.
[MENU/GRP]
The multi-function meter also displays the internal
temperature meter.
➥ Select G-2 (Multi-meter).
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group G.
• Push [MENU/GRP] momentarily one or more times to
select the menu G-2 (Multi-meter).
Quick entry
Z(BAND)] for 1 sec. to turn the
➥ Push and hold [Z
multi-function meter ON and OFF.
Z(MENU/GRP)] also to turn OFF.
• Push [Z
[Z]
36
3
BASIC OPERATION
■ Lock functions
The lock function can only be activated when displaying frequency, not in set mode or memory channel listing display.
D Dial lock function
The dial lock function prevents accidental change
caused by [DIAL].
➥ Push and hold [SPCH/LOCK] for 1 sec. to turn the
dial lock function ON and OFF.
•“
” indicator appears while the dial lock function is
activated.
Appears
[SPCH/LOCK]
D Microphone lock function
This function locks microphone keypads.
➥ Push and hold [SPCH/LOCK] (microphone) for 1
sec. to toggle the microphone lock function ON
and OFF.
SPCH
/LOCK
SPCH
/LOCK
1.8
• “MIC LOCK ON” and “MIC LOCK OFF,” popup indicators appear, respectively
• [PTT] and [SPCH/LOCK] can be used.
• All keys on the transceiver can be used.
10
21
50
1
4
7
.
3.5
14
24
TUNER
/CALL
2
5
8
144
0
XFC
V/M
MW
F-1
F-2
7
18
28
3
MODE
6
FIL
9
GENE
430
CE
F-INP
ENT
HM-151
■ Basic transmit operation
D Transmitting
Before transmitting, monitor your selected operating frequency to make sure transmitting
won’t cause interference to other stations on
the same frequency. It’s good Amateur practice
to listen first. On the HF bands, even if nothing
is heard, ask “is the frequency in use” once or
twice, before you begin operating on that frequency.
q Push [PTT] (microphone) to transmit.
SPCH
/LOCK
TUNER
/CALL
[PTT]
XFC
V/M
MW
F-1
F-2
[TX]
1.8
10
21
50
1
4
7
.
3.5
14
24
2
5
8
144
0
7
18
28
3
MODE
6
FIL
9
GENE
430
CE
F-INP
ENT
HM-151
• [TX] indicator lights red.
w Release [PTT] (microphone) to return to receive.
37
[TX] indicator
BASIC OPERATION
3
D Setting output power
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-1 QS] to enter the quick set mode.
RF Power.”
e Push [F-1 Y] or [F-2 Z] to select “R
r Rotate [DIAL] to set the desired output setting.
[AF]
• Output power is displayed in 1% steps (0% to 100%).
Z(MENU/GRP)] to exit quick set mode.
t Push [Z
• Available power
BAND
HF
50 MHz
144 MHz
430 MHz
SSB/CW
RTTY/FM
2–100 W
2-100 W
2–50 W
2–35 W
[MENU/GRP] [F-1] [F-2]
[DIAL]
AM*
1–40 W
1–40 W
2–20 W
2–14 W
3
*Carrier power
If a linear amplifier is connected such as the IC-PW1/EURO,
set the output power using the ALC meter (see below) to the
ALC zone (ALC meter reading should be within this zone),
otherwise the linear amplifier will not work properly.
D Setting microphone gain
Microphone gain must be adjusted properly so that
your signal is not distorted when transmitted.
[AF]
q Select SSB or another phone mode (AM or FM
mode).
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
[MENU/GRP] [F-1] [F-2] [F-3]
[DIAL]
e Push [F-3 MET] one or more times to select the
ALC meter.
• “ALC” appears.
r Push [AF(SET)] momentarily to enter the set mode
menu.
t Push [F-1 QS] to enter the quick set mode.
MIC Gain.”
y Push [F-1 Y] or [F-2 Z] to select “M
u Push [PTT] (microphone) to transmit.
• Speak into the microphone at your normal voice level.
i While speaking into the microphone, rotate [DIAL]
so that the ALC meter reading does not go outside
the ALC zone.
• Microphone gain is adjusted in 1% steps (0% to 100%).
o Release [PTT] (microphone) to return to receive.
!0 Push [Z(MENU/GRP)] to exit the quick set mode.
ALC
ALC zone
Z(MENU/GRP)] again to return the normal oper• Push [Z
ating mode.
38
4
RECEIVE AND TRANSMIT
■ Operating SSB
q Push [ Y(BAND)]/[ Z(BAND)] to select the desired
band or push a band key on the HM-151.
w Push [MODE] momentarily or push and hold for
1 sec. to select LSB or USB mode.
[AF]
[MODE]
[TX] indicator
[Y]
• Below 10 MHz LSB is automatically selected; above
10 MHz USB is automatically selected.
e Rotate [DIAL] to tune in a desired signal.
[Z]
• The S-meter indicates received signal strength when
signal is received.
r Rotate [AF] to set audio to a comfortable listening
level.
t Push [PTT] (microphone) to transmit.
[DIAL]
“LSB” or “USB” appears
• [TX] indicator lights red.
y Speak into the microphone at your normal voice
level.
• Adjust ‘MIC Gain’ at this step, if necessary. (p. 38)
u Release [PTT] (microphone) to return to receive.
D Convenient functions for receive
• Preamp and attenuator (p. 72)
➥ Push [P.AMP/ATT] momentarily to turn the preamp ON or OFF.
•“
” appears when the preamp is set to ON.
➥ Push [P.AMP/ATT] for 1 sec. to turn the attenuator ON.
• Push [P.AMP/ATT] momentarily to turn the attenuator
OFF.
•“
” appears when the attenuator is set to ON.
• Twin PBT (passband tuning) (p. 77)
➥ Push [PBT/M-ch/RIT] (switch) momentarily once
or twice to select the twin PBT ON or OFF (M-ch
RIT).
• PBT indicator lights green when the twin PBT is selected.
➥ Rotate [PBT/M-ch/RIT] (controls–inner/outer).
• Push [PBT/M-ch/RIT(CLR)] to clear the settings.
• AGC (auto gain control) (p. 74)
M-3” is selected, push [F-3 AGC] momen➥ While “M
tarily one or more times to select AGC fast, AGC
middle and AGC slow.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
,” “
” and “
” appears when the
fast time constant, middle time constant and slow
time constant is selected, respectively.
M-3” is selected, push and hold [F-3 AGC]
➥ While “M
for 1 sec. to enter the AGC set mode.
• Push [F-2 FAST], [F-3 MID] or [F-4 SLOW] to select
the time constant, then rotate [DIAL] to adjust the time
constant.
39
• Noise blanker (p. 78)
➥ Push [NB/ADJ] to turn the noise blanker ON and
OFF.
•“
” appears when the noise blanker is set to ON.
➥ Push and hold [NB/ADJ] for 1 sec. to enter the
noise blanker set mode, then rotate [DIAL] to adjust the threshold level, or noise pulse width.
• DSP noise reduction (p. 79)
➥ Push [NR/LEV] to turn the DSP noise reduction
ON and OFF.
•“
” appears when the DSP noise reduction is ON.
➥ Push and hold [NR/LEV] for 1 sec. to enter the
DSP noise reduction level set mode, then rotate
[DIAL] to adjust the DSP noise reduction level.
• Manual notch filter (pgs. 80, 81)
➥ Push [MNF/ADJ] to turn the manual notch filter
ON and OFF.
•“
” appears when the manual notch filter is set to ON.
➥ Push and hold [MNF/ADJ] for 1 sec. to enter the
manual notch filter set mode.
• Push [F-2 NF1], [F-3 NF2] to select the notch filter,
push [F-4 NW] to set the filter width, rotate [DIAL] to
set the notch frequency.
• Auto notch filter (p. 80)
➥ Push [ANF/• REC] to turn the auto notch filter ON
and OFF.
•“
” appears when the auto notch filter is set to ON.
• VSC (voice squelch control) (p. 82)
S-1” is selected, push [F-4 VSC] to turn
➥ While “S
the VSC function ON and OFF.
•“
” appears when VSC function is set to ON.
RECEIVE AND TRANSMIT
4
D Convenient functions for transmit
• Transmit quality monitor (p. 87)
➥ Push [AF(SET)], then [F-4 OTH] to enter the miscellaneous (others) set mode. Select an item with
[F-1 ≤]/[F-2 ≥], then rotate [DIAL] to turn the
monitor function ON and OFF.
• VOX (voice operated transmit) (p. 83)
M-3” is selected, push [F-1 VOX] to turn
➥ While “M
the VOX function ON and OFF.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
” appears when the VOX function is set to ON.
M-3” is selected, push and hold [F-1 VOX]
➥ While “M
for 1 sec. to enter the VOX set mode.
• Push [F-1 ≤]/[F-2 ≥] to select an item.
• Rotate [DIAL] to set the value/conditions.
• Speech compressor (p. 87)
M-3” is selected, push [F-2 COM] to turn
➥ While “M
the speech compressor ON and OFF.
•“
” appears when the speech compressor is set to
ON.
M-3” is selected, push and hold [F-2 COM]
➥ While “M
for 1 sec. to enter the compression level set
mode.
• Rotate [DIAL] to adjust the compression level.
• Transmit filter width (p. 84)
M-3” is selected, push [F-4 TBW] momen➥ While “M
tarily to display the selected transmit filter width.
M-3” is selected, push and hold [F-4 TBW]
➥ While “M
for 1 sec. to select the transmit filter width from
narrow, middle and width.
• The transmit filter width window appears for showing
the selected transmit filter width each time [F-4 TBW]
is pushed.
4
D About 5 MHz band operation (USA version only)
IC-7000 Display
Frequency*
FCC Channel
Center Frequency*
5.33050 MHz
5.34650 MHz
5.36650 MHz
5.37150 MHz
5.40350 MHz
5.33200 MHz
5.34800 MHz
5.36800 MHz
5.37300 MHz
5.40500 MHz
To assist you in operating the 5 MHz band correctly
within the rules specified by the FCC, transmission
is impossible on any 5 MHz band frequency other
than the 5 frequencies indicated in the table above.
Operation on the 5 MHz band is allowed on 5 discrete
frequencies and must adhere to the following:
• USB mode
• Maximum of 50 watts ERP (Effective Radiated Power)
• 2.8 kHz bandwidth
It is the operator’s responsibility to set all controls so
that the transmission in this band meets the stringent
conditions under which we may use these frequencies.
NOTE: We recommend that you store these frequencies, mode and filter settings into the memory
channel for easy recall.
*The channel center frequencies that are specified
by the FCC, show the center frequency of their
passband. However, the IC-7000 displays carrier
point frequency, so set 1.5 kHz below from FCC
channel center frequency.
40
4
RECEIVE AND TRANSMIT
■ Operating CW
q Connect a paddle or straight key as on page 22.
Y(BAND)]/[Z
Z(BAND)] to select the desired
w Push [Y
band or push a band key on the HM-151.
e Push [MODE] momentarily to select CW mode.
[AF]
[MODE]
[TX] indicator
[Y]
• After CW mode is selected, push and hold [MODE] for
1 sec. to toggle between CW and CW-R modes.
r Rotate [DIAL] to tune in a desired signal with the
desired tone frequency.
t Rotate [AF] to set audio to a comfortable listening
level.
y Set CW break-in operation as semi break-in, full
break-in or OFF.
[Z]
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
“CW” or “CW-R” appears
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
• Push [F-1 BRK] one or more times to select the CW
break-in operation.
•“
,” “
,” and “OFF (no indication)” appears.
➧ BK-IN : semi break-in
➧ F-BK : full break-in
➧ OFF : no break-in (ACC socket connection is necessary as shown on page 22.)
Appears
u Set the CW delay time when semi break-in operation is selected.
• Push and hold [F-1 BRK] for 1 sec. to enter the breakin delay time set mode.
• Rotate [DIAL] to set the desired delay time.
S-1).
i Set CW setting in the keyer set mode (S
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
Semi break-in operation is selected.
Z(MENU/GRP)], then [F-4 SET ] to
• Push [F-2 KEY ], [Z
enter the keyer set mode. (p. 49)
o Keying to transmit, use the electric keyer or paddle
to send your CW signals.
• [TX] indicator lights red.
• The Po meter indicates transmitted CW signal strength.
!0 Stop keying to return to receive.
Delay time of 7.5 dots is selected
for semi break-in operation.
41
RECEIVE AND TRANSMIT
4
D Convenient functions for receive
• Preamp and attenuator (p. 72)
➥ Push [P.AMP/ATT] momentarily to turn the preamp ON or OFF.
•“
” appears when the preamp is set to ON.
➥ Push [P.AMP/ATT] for 1 sec. to turn the attenuator ON.
• Push [P.AMP/ATT] momentarily to turn the attenuator
OFF.
•“
” appears when the attenuator is set to ON.
• Twin PBT (passband tuning) (p. 77)
➥ Push [PBT/M-ch/RIT] (switch) momentarily once
or twice to select the twin PBT ON or OFF (M-ch
RIT).
• PBT indicator lights green when the twin PBT is selected.
➥ Rotate [PBT/M-ch/RIT] (controls–inner/outer).
• Push [PBT/M-ch/RIT(CLR)] to clear the settings.
• AGC (auto gain control) (p. 74)
M-3” is selected, push [F-3 AGC] momen➥ While “M
tarily one or more times to select AGC fast, AGC
middle and AGC slow.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
,” “
” and “
” appears when the
fast time constant, middle time constant and slow
time constant is selected, respectively.
M-3” is selected, push and hold [F-3 AGC]
➥ While “M
for 1 sec. to enter the AGC set mode.
• Push [F-2 FAST], [F-3 MID] or [F-4 SLOW] to select
the time constant, then rotate [DIAL] to adjust the time
constant.
• Noise blanker (p. 78)
➥ Push [NB/ADJ] to turn the noise blanker ON and
OFF.
•“
” appears when the noise blanker is set to ON.
➥ Push and hold [NB/ADJ] for 1 sec. to enter the
noise blanker set mode, then rotate [DIAL] to adjust the threshold level, or noise pulse width.
• DSP noise reduction (p. 79)
➥ Push [NR/LEV] to turn the DSP noise reduction
ON and OFF.
•“
” appears when the DSP noise reduction is set to
ON.
➥ Push and hold [NR/LEV] for 1 sec. to enter the
noise reduction level set mode, then rotate [DIAL]
to adjust the DSP noise reduction level.
• Manual notch filter (pgs. 80, 81)
➥ Push [MNF/ADJ] to turn the manual notch filter
ON and OFF.
4
•“
” appears when the manual notch filter is set to
ON.
➥ Push and hold [MNF/ADJ] for 1 sec. to enter the
manual notch filter set mode.
• Push [F-2 NF1], [F-3 NF2] to select the notch filter,
push [F-4 NW] to set the filter width, rotate [DIAL] to
set the attenuated frequency.
• 1⁄4 function (p. 32)
M-3” is selected, push [F-2 1/4] to turn
➥ While “M
the 1⁄4 function ON and OFF.
•“
” indicator appears when the function is activated.
• CW pitch control (p. 44)
➥ Push [AF(SET)], then [F-1 QS] to enter the quick
set mode. Select an item with [F-1 ≤]/[F-2 ≥],
then rotate [DIAL] to set the desired CW pitch
from 300 to 900 Hz in 5 Hz steps.
D Convenient functions for transmit
• Break-in function (p. 85)
M-3” is selected, push [F-1 BRK] one or
➥ While “M
more times to select the CW break-in operation.
• Memory keyer function (p. 45)
S-1” is selected, push [F-2 KEY] to enter
➥ While “S
the keyer set memu.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
” or “
” appears when the semi break-in or
full break-in is set to ON, respectively.
42
4
RECEIVE AND TRANSMIT
D CW reverse mode
The CW-R (CW Reverse) mode receives CW signals
on the reverse sideband like that of LSB and USB
modes.
[MODE]
Use when interference is near the desired signal and
you want to change the interference tone.
q Push [MODE] momentarily several times to select
CW mode.
w Push and hold [MODE] for 1 sec. to select CW or
CW-R mode.
• Receive audio tone response
600 Hz
• Check the interference tone.
600 Hz
Push
for 1 sec.
BFO
inteference
signal
inteference signal
BFO
CW mode (LSB side)
CW-R mode (USB side)
D CW side tone function
When the transceiver is in receive condition (and the
break-in function is OFF— p. 85) you can listen to the
tone of your CW signal without actually transmitting.
[AF]
This allows you to spot your transmit signal exactly to
another station’s. This also convenient for CW practice.
q When CW (CW-R) mode is selected, enter the
quick set mode.
• Push [AF(SET)] momentarily to enter the set mode
menu.
• Push [F-1 QS] to enter the quick set mode.
w Push [F-1 ≤] or [F-2 ≥] several times to select
Side Tone Level,” then rotate [DIAL] to ad“S
just the side tone level.
• Side tone level is adjusted in 1% steps (0% to 100%).
Z(MENU/GRP)] to exit the quick set mode.
e Push [Z
Z(MENU/GRP)] again to return the normal oper• Push [Z
ating mode.
43
[MENU/GRP] [F-1] [F-2]
[DIAL]
RECEIVE AND TRANSMIT
4
D CW pitch control
The received CW audio pitch and monitored CW
audio pitch can be adjusted to suit your preferences
(300 to 900 Hz) without changing the operating frequency.
[AF]
q When CW (CW-R) mode is selected, enter the
quick set mode.
• Push [AF(SET)] momentarily to enter the set mode
menu.
• Push [F-1 QS] to enter the quick set mode.
CW
w Push [F-1 ≤] or [F-2 ≥] several times to select “C
Pitch ,” then rotate [DIAL] to set the desired
pitch.
[MENU/GRP] [F-1] [F-2]
[DIAL]
• CW pitch is adjusted in 5 Hz steps (300 to 900 Hz).
Z(MENU/GRP)] to exit the quick set mode.
e Push [Z
Z(MENU/GRP)] again to return the normal oper• Push [Z
ating mode.
4
• This shows the default setting for the CW pitch control
(600 Hz).
44
4
RECEIVE AND TRANSMIT
■ Electronic CW keyer
The IC-7000 has a number of convenient functions for
the electronic keyer that can be accessed from the
memory keyer menu.
[MODE]
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
[DIAL]
q Push [MODE] to select CW mode.
w Select S-1. (See right page.)
e Push [F-2 KEY] to enter the keyer send menu.
Z(MENU/GRP)] to select the keyer root menu.
r Push [Z
t Push one of the multi-function keys ([F-1] to [F-4])
to select the desired menu. See the diagram below.
Z(MENU/GRP)] to return to the previous indica• Push [Z
tion.
The memory keyer root menu can also be set
to the starting menu for keyer operation in the
miscellaneous (others) set mode. (p.134)
¡Memory keyer edit menu
¡Memory keyer send menu
¡Contest number set mode
¡Memory keyer root menu
¡Keyer set mode
45
RECEIVE AND TRANSMIT
4
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: S)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
D Memory keyer send menu
Pre-set messages can be sent using the memory
keyer send menu. Contents of the memory keyer are
set using the edit menu.
• Transmitting
q Select CW mode with [MODE].
w Set the break-in function ON (p. 85).
• When step t is performed with the break-in function
OFF, the memory keyer contents are monitored.
[MODE]
e Select S-1.
r Push [F-2 KEY] to enter the keyer send menu.
4
• If the keyer root menu appears, push [F-1 SND]. The
keyer starting menu can be changed in the miscellaneous (others) set mode (p. 134).
[MENU/GRP]
t Push [F-1 M1] — [F-4 M4] momentarily to transmit
the contents one time; push and hold these keys
for 1 sec. to transmit the contents repeatedly.
[F-1]
[F-2] [F-3] [F-4]
M1”– “M
M4” are highlighted while transmitting.
• “M
(” and “)
)” appear while transmitting repeatedly.
• “(
• While transmitting repeatedly, push any function key to
cancel the transmission.
• Set the repeat interval of the memory keyer to 1–60
sec. (1 sec. steps). See p. 49 for keyer set mode.
• To decrement the contact number, push
Y(MENU/GRP)].
[Y
• Memory keyer send menu
Contact number
Memory keyer
content
Z(MENU/GRP)] twice to exit the memory
y Push [Z
keyer send menu and return to normal CW mode
indication.
46
4
RECEIVE AND TRANSMIT
D Editing a keyer memory
The contents of the memory keyer memories can be
set using the memory keyer edit menu. The memory
keyer can memorize and re-transmit 4 CW sequences for often-used CW messages, contest number, etc. Total capacity of the memory keyer is 55
characters per memory channel.
• Programming contents
q Push [MODE] to select CW mode.
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
Z(MENU/GRP)] to select the
e Push [F-2 KEY] then [Z
keyer root menu.
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
• If the keyer root menu appears, skip pushing
Z(MENU/GRP)]. The keyer starting menu can be
[Z
changed in the miscellaneous (others) set mode. (p.
134)
r Push [F-2 EDT] to enter the keyer edit menu.
t Push [F-1 M1 ] — [F-4 M4 ] to select the desired
keyer memory channel.
Y(MENU/GRP)] several times to select the dey Push [Y
sired character group ([ABC], [123] or [etc]).
Key selection
Editable characters
ABC
A to Z (capital leters)
123
0 to 9 (numbers)
etc
/ ? ^. ,@✽
Memory channel select
NOTE:
“^” is used to transmit a following word with no
space such as AR. Put “^” before a text string
such as ^AR, and the CW prosign “ AR ” is sent
with no space.
“✱” is used to insert the CW contest number.
The contest number automatically increments
by 1. This function is only available for one
memory keyer channel at a time. Memory
keyer channel M2 uses “✱” by default.
Selected
character
u Select the desired character by rotating [DIAL] or
by pushing the band
key (HM-151)
for the increABC
KEYER EDIT
CQ TEST CQ TEST DE ICOM ICOM
M1
T E Snumber
T
menting trigger memory
input.
UR 5NN001 BK
• Pre-programmed contents
47
CH
Contents
M1
CQ TEST CQ TEST DE ICOM ICOM TEST
M2
UR 5NN✽ BK
M3
CFM TU
M4
QRZ?
M2
ABC
Ç] for cursor movement.
• Push [F-1 Å
] or [F-2
CFM TU
M3
• Push [F-3 DEL] to delete the selected character.
123
QRZ?
M4
• Push [F-4 SPC] to input a space.
ç
SPACE
M1..M4
å
• “✱” is for contact numbers andDEL
can only
be used
on the
memory channel used to increment the contact number (“ ” appears next to that channel).
i Repeat steps y and u until the desired contents
are input.
Z(MENU/GRP)] to return to memory channel
o Push [Z
selection mode, then select the next memory channel and repeat steps y and i for character input,
if desired.
Z(MENU/GRP)] twice to exit the keyer edit
!0 Push [Z
mode.
RECEIVE AND TRANSMIT
4
D Contest number set mode
This menu is used to set the contest (serial) number
and incrementing trigger channel, etc.
[MODE]
• Setting the contact (serial) number
Contact number can be automatically transmitted
from one of the memory keyer channels. The Morse
cut numbers can be used as the contact numbers.
The maximum number for contact numbers is 9999.
q Select CW mode with [MODE].
w Select S-1.
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
Z(MENU/GRP)] to select the
e Push [F-2 KEY] then [Z
keyer root menu.
• If the keyer root menu appears, skip pushing
Z(MENU/GRP)]. The keyer starting menu can be
[Z
changed in the miscellaneous (others) set mode. (see
p.134)
r Push [F-3 001] to enter the contest number set
menu.
t Push [F-1 ≤] or [F-2 ≥] to select the desired set
item.
4
• Push and hold [F-4 DEF] for 1 sec. to select the default condition or value.
Z (MENU/GRP)] twice to exit the contest numy Push [Z
ber set menu and return to normal CW mode indication.
1 Number Style
This item sets the numbering system used for contest
(serial) numbers— normal or cut numbers.
Normal
: Does not use morse cut number
(default)
190➜ANO: Sets 1 as A, 9 as N and 0 as O.
190➜ANT : Sets 1 as A, 9 as N and 0 as T.
90➜ NO : Sets 9 as N and 0 as O.
90➜ NT : Sets 9 as N and 0 as T.
2 Count UP Trigger
This selects which of the four memory channels will
send the contest serial number. The count up trigger
increments the serial number automatically after each
complete serial number is sent.
• M1, M2, M3 and M4 can be set. (default: M2)
3 Present Number
This item shows the current number in the count up
trigger channel set above.
• Rotate [DIAL] to change the number, or push [F-4
CLR] for 1sec. to reset the current number to 001.
48
4
RECEIVE AND TRANSMIT
D Keyer set mode
This set mode is used to set the memory keyer repeat
time, dash weight, paddle specifications, keyer type,
etc.
• Setting the electronic keyer
q Select CW mode with [MODE].
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
[MODE]
Z(MENU/GRP)] to select the
e Push [F-2 KEY] then [Z
keyer root menu.
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
• If the keyer root menu appears, skip pushing
Z(MENU/GRP)]. The keyer starting menu can be
[Z
changed in the miscellaneous (others) set mode. (see
p.134)
r Push [F-4 SET] to enter the keyer set menu.
t Push [F-1 ≤] or [F-2 ≥] to select the desired set
item.
• Push and hold [F-4 DEF] for 1 sec. to select the default condition or value.
Z(MENU/GRP)] twice to exit the keyer set
y Push [Z
menu and return to normal CW mode indication.
1 Keyer Repeat Time
When sending CW using the repeat timer, this item
sets the time between transmission.
• 1 to 60 sec. in 1 sec. steps can be selected.
• Push and hold [F-4 DEF] for 1 sec. to select a default setting. (default: 2 sec.)
2 Dot/Dash Ratio
This item sets the dot/dash ratio.
Keying weight example: Morse code “K”
DOT (Fixed*)
Weight setting:
1:1:3 (default)
DASH
DASH
Weight setting:
Adjusted
Adjustable range
SPACE (Fixed*)
*SPACE and DOT length can be adjusted with
“Key Speed” only in the quick set mode.
49
• 1 : 1 : 2.8 to 1 : 1 : 4.5 can be set.
• Check the ratio with side tone in CW mode.
• Push and hold [F-4 DEF] for 1 sec. to select a default ratio of 1 : 1 : 3.0.
RECEIVE AND TRANSMIT
4
D Keyer set mode (continued)
3 Rise Time
This item sets the envelop rise time during which the
output power reaches the set transmit power.
• 2, 4, 6, or 8 msec. can be selected.
• Push and hold [F-4 DEF] for 1 sec. to select a default setting. (default: 4 sec.)
• About rise time
Key action
Tx
Rx
Set Tx power level
Tx output power
0
Rise time
Time
4 Paddle Polarity
This item sets the paddle polarity.
• Normal and reverse polarity can be selected.
• Push and hold [F-4 DEF] for 1 sec. to select a default setting. (default: Normal)
4
5 Keyer Type
This item selects the keyer type for [KEY] connector
on the rear panel.
6 MIC U/D Keyer (HM-103)
(Microphone’s [UP]/[DN] switches keyer)
This item allows you to set the microphone [UP]/[DN]
switches to be used as a paddle.
• ELEC-KEY, BUG-KEY and Straight key can be selected.
• Push and hold [F-4 DEF] for 1 sec. to select a default setting. (default: ELEC-KEY)
• ON : [UP]/[DN] switches can be used for CW.
• OFF: [UP]/[DN] switches cannot be used for CW.
• Push and hold [F-4 DEF] for 1 sec. to select a default setting. (default: OFF)
NOTE: When “ON” is selected, the frequency and
memory channel cannot be changed using the
[UP]/[DN] switches.
D Paddle operation from [MIC] connector
Connect a CW paddle as at right to operate an electronic keyer from the front panel [MIC] connector.
• This function is available from the front panel mic
connector only.
Paddle Polarity,” “K
Keyer
• Be sure to select “P
Type” “M
MIC U/D Keyer (HM-103)” in the
keyer set mode. (see above)
• Connect straight key to “DOT” side.
• Push both of “DOT” and “DASH to activate the
squeeze operation.
CW
paddle
MIC connector
DOT
Eu
3.9 kΩ ±5%
MIC U/D w
DASH
2.2 kΩ ±5%
NOTE: The HM-103 can be operate as a CW paddle from both of the front panel and rear panel mic
connector. But the HM-103 is not available the
squeeze operation.
50
4
RECEIVE AND TRANSMIT
■ Operating RTTY (FSK)
When using your RTTY terminal or TNC, consult the
manual that comes with the RTTY terminal or TNC.
[AF]
[MODE]
[TX] indicator
Y(BAND)]/[Z
Z(BAND)] to select the desired
q Push [Y
band or push a band key on the HM-151.
w Push [MODE] momentarily to select RTTY mode.
[Y]
• After RTTY mode is selected, push and hold [MODE]
for 1 sec. to toggle between RTTY and RTTY-R modes.
[Z]
e Display the RTTY decoder screen.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
• Push [F-2 DEC] to display the Baudot decoder screen.
r Rotate [DIAL] to tune in a desired signal.
• Use [F-2 1/4] in the M-3 display when critical setting
is required.
• S-meter indicates received signal strength when signal
is received.
• If the received signal cannot be demodulated, try selecting RTTY-R mode (or RTTY mode).
t Transmit a SEND signal from your TNC.
• [TX] indicator lights red.
• The Po meter indicates transmitted RTTY signal
strength.
y Operate the connected PC or TNC (TU) to transmit RTTY (FSK) signals.
51
[MENU/GRP]
[F-2]
“RTTY” or “RTTY-R” appears
[DIAL]
RECEIVE AND TRANSMIT
4
D Convenient functions for receive
• Preamp and attenuator (p. 72)
➥ Push [P.AMP/ATT] momentarily to turn the preamp ON or OFF.
•“
” appears when the preamp is set to ON.
➥ Push [P.AMP/ATT] for 1 sec. to turn the attenuator ON.
• Push [P.AMP/ATT] momentarily to turn the attenuator
OFF.
•“
” appears when the attenuator is set to ON.
• Twin PBT (passband tuning) (p. 77)
➥ Push [PBT/M-ch/RIT] (switch) momentarily once
or twice to select the twin PBT ON or OFF (M-ch
RIT).
• PBT indicator lights green when the twin PBT is selected.
➥ Rotate [PBT/M-ch/RIT] (controls–inner/outer).
• Push [PBT/M-ch/RIT(CLR)] to clear the settings.
• AGC (auto gain control) (p. 74)
M-3” is selected, push [F-3 AGC] momen➥ While “M
tarily one or more times to select AGC fast, AGC
middle and AGC slow.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
,” “
” and “
” appears when the
fast time constant, middle time constant and slow
time constant is selected, respectively.
M-3” is selected, push and hold [F-3 AGC]
➥ While “M
for 1 sec. to enter the AGC set mode.
• Noise blanker (p. 78)
➥ Push [NB/ADJ] to turn the noise blanker ON and
OFF.
•“
” appears when the noise blanker is set to ON.
➥ Push and hold [NB/ADJ] for 1 sec. to enter the
noise blanker set mode, then rotate [DIAL] to adjust the threshold level, or noise pulse width.
• DSP noise reduction (p. 79)
➥ Push [NR/LEV] to turn the DSP noise reduction
ON and OFF.
•“
” appears when the DSP noise reduction is set to
ON.
➥ Push and hold [NR/LEV] for 1 sec. to enter the
noise reduction level set mode, then rotate [DIAL]
to adjust the DSP noise reduction level.
• Manual notch filter (pgs. 80, 82)
➥ Push [MNF/ADJ] to turn the manual notch filter
ON and OFF.
4
•“
” appears when the manual notch filter is set to
ON.
➥ Push and hold [MNF/ADJ] for 1 sec. to enter the
manual notch filter set mode.
• Push [F-2 NF1], [F-3 NF2] to select the notch filter,
push [F-4 NW] to set the filter width, rotate [DIAL] to
set the attenuated frequency.
• 1⁄4 function (p. 32)
M-3” is selected, push [F-2 1/4] to turn
➥ While “M
the 1⁄4 function ON and OFF.
•“
” indicator appears when the function is activated.
• Push [F-2 FAST], [F-3 MID] or [F-4 SLOW] to select
the time constant, then rotate [DIAL] to adjust the time
constant.
52
4
RECEIVE AND TRANSMIT
D RTTY reverse mode
Received characters are occasionally garbled when
the receive signal is reversed between MARK and
SPACE. This reversal can be caused by incorrect
TNC connections, settings, commands, etc.
[MODE]
To receive a reversed RTTY signal correctly, select
RTTY-R (RTTY reverse) mode.
q Push [MODE] momentarily several times to select
RTTY mode.
w Push and hold [MODE] for 1 sec. to select RTTY or
RTTY-R mode.
Normal
Reverse
Space Mark
170
Hz
Space Mark
2125
Hz
2125
Hz
BFO
170
Hz
BFO
displayed freq.
displayed freq.
D Twin peak filter
The twin peak filter changes the receive frequency response by boosting 2 particular frequencies (2125 and
2295 Hz) for better copying of desired RTTY signals.
[AF]
q Push [MODE] momentarily to select RTTY mode.
• After RTTY mode is selected, push [MODE] for 1 sec.
to toggle between RTTY and RTTY-R modes.
w Push [AF(SET)] momentarily to enter the set mode
menu.
e Push [F-1 QS] to enter the quick set mode.
Twin Peak
r Push [F-1 ≤] or [F-2 ≥] to select “T
Filter.”
t Rotate [DIAL] to select the twin peak filter function
ON or OFF.
• The received audio volume may become greater when
the twin peak filter is turned ON.
Z(MENU/GRP)] twice to return the normal opy Push [Z
erating mode.
53
[MENU/GRP] [F-1] [F-2]
[DIAL]
RECEIVE AND TRANSMIT
4
D Function for the RTTY decoder indication
The transceiver has an RTTY decoder for Baudot
(mark freq.: 2125 Hz, shift freq.: 170 Hz, 45 bps).
An external terminal unit (TU) or terminal node controller (TNC) is not necessary for receiving a Baudot
signal.
q Push [MODE] momentarily to select RTTY mode.
• After RTTY mode is selected, push [MODE] for 1 sec.
to toggle between RTTY and RTTY-R modes.
[MENU/GRP] [F-1] [F-2]
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
e Push [F-2 DEC] momentarily to turn the RTTY decoder ON.
RTTY tuning meter
• When tuned into an RTTY signal, decoded characters
are displayed in the RTTY decoder screen.
r Push [F-1 HLD] momentarily to freeze the current
screen.
4
• “H” appears while the function is in use.
Y(MENU/GRP)] to toggle the normal or wide
t Push [Y
screen space.
y Push and hold [F-1 HLD] for 1 sec. to clear the displayed characters.
Z(MENU/GRP)] to exit the RTTY decoder
u Push [Z
screen.
The transceiver has an RTTY tuning iindicator to
make correct tuning easier.
The RTTY tuning meter is automatically displayed
when the RTTY decoder is turned ON.
D Setting the decoder threshold level
Adjust the RTTY decoder threshold level if some
characters are displayed when no signal is received.
q Call up the RTTY decoder screen as described
above.
w Push [F-3 ADJ] to select the threshold level setting condition.
e Rotate [DIAL] to adjust the RTTY decoder threshold level.
• Push and hold [F-4 DEF] for 1 sec. to select the default condition.
Z(MENU/GRP)] to exit the RTTY decoder
r Push [Z
screen.
[MENU/GRP]
[F-3]
[F-4]
[DIAL]
The UnShift On Space (USOS) function and new
line code can be set in the RTTY decode set mode.
(p. 55)
54
4
RECEIVE AND TRANSMIT
D RTTY decode set mode
This set mode is used to set the decode USOS function, etc.
q Push [MODE] momentarily to select RTTY mode.
• After RTTY mode is selected, push [MODE] for 1 sec.
to toggle between RTTY and RTTY-R modes.
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
e Push [F-2 DEC] momentarily to turn the RTTY decoder ON.
• RTTY decoder screen appears.
r Push [F-4 SET ] to select the RTTY decode set
mode.
t Push [F-1 ≤] or [F-2 ≥] to select the desired set
item.
y Set the desired condition using [DIAL].
• Push [F-4 DEF] for 1 sec. to select a default condition
or value.
Z(MENU/GRP)] to exit from set mode.
u Push [Z
1 RTTY Decode USOS
This item selects the USOS (UnShift On Space) function of the internal RTTY decoder.
ON
OFF
Decode space as letter code Decode space as character
(default)
code
2 RTTY Decode New Line Code
This item selects the new line code of the internal
RTTY decoder.
CR : Carriage Return
LF : Line Feed
55
CR,LF,CR+LF
CR+LF
CR, LF and CR+LF
(default)
CR+LF only
RECEIVE AND TRANSMIT
4
D Pre-setting for using RTTY terminal or TNC
When using your RTTY terminal or TNC, consult the
manual that comes with the RTTY terminal or TNC.
[AF]
[MODE]
Mark frequency
q Push [MODE] momentarily to select RTTY mode.
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
RTTY mark frequency
is set to 2125 Hz.
(default)
2125, 1615 and 1275
Hz are available.
• After RTTY mode is selected, push [MODE] for 1 sec.
to toggle between RTTY and RTTY-R modes.
w Push [AF(SET)] momentarily to enter the set mode
menu.
e Push [F-1 QS] to enter the quick set mode.
RTTY Mark
r Push [F-1 Y] or [F-2 Z] to select “R
Frequency.”
t Rotate [DIAL] to select the desired frequency.
4
• Push and hold [F-4 DEF] for 1 sec. to select the default frequency.
170/200/425 Hz are
available.
Shift width
q Enter the quick set mode as above.
RTTY Shift
w Push [F-1 Y] or [F-2 Z] to select “R
Width.”
e Rotate [DIAL] to select the desired shift width.
RTTY keying is set to
‘normal’. (default)
normal :
key open=mark
key close=space
RTTY keying polarity
q Enter the quick set mode as above.
RTTY key w Push [F-1 Y] or [F-2 Z] to select “R
ing Polarity.”
e Rotate [DIAL] to select the desired keying polarity.
RTTY shift width is
set to 170 Hz.
(default)
reverse:
key open=space
key close=mark
• Push and hold [F-4 DEF] for 1 sec. to select the default shift width.
• Push and hold [F-4 DEF] for 1 sec. to select the default polarity.
Z(MENU/GRP)]
After Pre-setting is finished, push [Z
twice to return the normal operating mode.
56
4
RECEIVE AND TRANSMIT
■ Operating AM
Z(BAND)] to select the desired
Y(BAND)]/[Z
q Push [Y
band or push a band key on the HM-151.
w Push [MODE] momentarily or push and hold for 1
sec. to select AM mode.
[AF]
[MODE]
[TX] indicator
[Y]
• After FM, WFM or AM mode is selected, push [MODE]
for 1 sec. to select from FM, WFM and AM modes.
[Z]
e Rotate [DIAL] to tune in a desired signal.
• The S-meter indicates received signal strength when a
signal is received.
• The default tuning step for AM mode is 1 kHz; this can
be changed using the tuning step program mode. (p. 30)
[DIAL]
“AM” appears
r Rotate [AF] to set audio to a comfortable listening
level.
t Push [PTT] (microphone) to transmit.
• [TX] indicator lights red.
y Speak into the microphone at your normal voice
level.
• Adjust ‘MIC Gain’ at this step, if necessary. (p. 38)
u Release [PTT] (microphone) to return to receive.
D Convenient functions for receive
• Preamp and attenuator (p. 72)
➥ Push [P.AMP/ATT] momentarily to turn the preamp ON or OFF.
•“
” appears when the preamp is set to ON.
➥ Push [P.AMP/ATT] for 1 sec. to turn the attenuator ON.
• Push [P.AMP/ATT] momentarily to turn the attenuator
OFF.
•“
” appears when the attenuator is set to ON.
• Twin PBT (passband tuning) (p. 77)
➥ Push [PBT/M-ch/RIT] (switch) momentarily once
or twice to select the twin PBT ON or OFF (M-ch
RIT).
• PBT indicator lights green when the twin PBT is selected.
➥ Rotate [PBT/M-ch/RIT] (controls–inner/outer).
• Push [PBT/M-ch/RIT(CLR)] to clear the settings.
• Noise blanker (p. 78)
➥ Push [NB/ADJ] to turn the noise blanker ON and
OFF.
•“
” appears when the noise blanker is set to ON.
➥ Push and hold [NB/ADJ] for 1 sec. to enter the
noise blanker set mode, then rotate [DIAL] to adjust the threshold level, or noise pulse width.
57
• AGC (auto gain control) (p. 74)
M-3” is selected, push [F-3 AGC] momen➥ While “M
tarily one or more times to select AGC fast, AGC
middle and AGC slow.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
,” “
” and “
” appears when the
fast time constant, middle time constant and slow
time constant is selected, respectively.
M-3” is selected, push and hold [F-3 AGC]
➥ While “M
for 1 sec. to enter the AGC set mode.
• Push [F-2 FAST], [F-3 MID] or [F-4 SLOW] to select
the time constant, then rotate [DIAL] to adjust the time
constant.
RECEIVE AND TRANSMIT
4
Convenient functions for receive (continued)
• DSP noise reduction (p. 79)
➥ Push [NR/LEV] to turn the DSP noise reduction
ON and OFF.
•“
” appears when the DSP noise reduction is set to
ON.
➥ Push [NR/LEV] for 1 sec. to enter the noise reduction level set mode, then rotate [DIAL] to adjust the DSP noise reduction level.
• Auto notch filter (p. 80)
➥ Push [ANF/• REC] to turn the auto notch filter ON
and OFF.
•“
” appears when the auto notch filter is set to ON.
• VSC (voice squelch control) (p. 82)
S-1” is selected, push [F-4 VSC] to turn
➥ While “S
the VSC function ON and OFF.
•“
” appears when VSC function is set to ON.
• Manual notch filter (pgs. 80, 81)
➥ Push [MNF/ADJ] to turn the manual notch filter
ON and OFF.
•“
” appears when the manual notch filter is set to
ON.
➥ Push and hold [MNF/ADJ] for 1 sec. to enter the
manual notch filter set mode.
• Push [F-2 NF1], [F-3 NF2] to select the notch filter,
push [F-4 NW] to set the filter width, rotate [DIAL] to
set the notch frequency.
4
D Convenient functions for transmit
• Transmit quality monitor (p. 87)
➥ Push [AF(SET)], then [F-4 OTH] to enter the miscellaneous (others) set mode. Select an item with
[F-1 ≤]/[F-2 ≥], then rotate [DIAL] to turn the
monitor function ON and OFF.
• VOX (voice operated transmit) (p. 83)
M-3” is selected, push [F-1 VOX] to turn
➥ While “M
the VOX function ON and OFF.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
•“
” appears when the VOX function is set to ON.
M-3” is selected, push and hold [F-1 VOX]
➥ While “M
for 1 sec. to enter the VOX set mode.
• Push [F-1 ≤]/[F-2 ≥] to select an item.
• Rotate [DIAL] to set the value/conditions.
58
4
RECEIVE AND TRANSMIT
■ Operating FM
q Push [ Y(BAND)]/[ Z(BAND)] to select the desired
band or push a band key on the HM-151.
w Push [MODE] momentarily or push and hold for 1
sec. to select FM mode.
[AF]
[MODE]
[TX] indicator
[Y]
• After FM, WFM or AM mode is selected, push [MODE]
for 1 sec. to select from FM, WFM and AM modes.
[Z]
e Rotate [DIAL] to tune in a desired signal.
• The S-meter indicates received signal strength when a
signal is received.
• The default tuning step for FM mode is 1 kHz; this can
be changed using the tuning step program mode. (p. 30)
[DIAL]
“FM” appears
r Rotate [AF] to set audio to a comfortable listening
level.
t Push [PTT] (microphone) to transmit.
• [TX] indicator lights red.
y Speak into the microphone at your normal voice
level.
• Adjust ‘MIC Gain’ at this step, if necessary. (p. 38)
u Release [PTT] (microphone) to return to receive.
D Convenient functions for receive
• Preamp and attenuator (p. 72)
➥ Push [P.AMP/ATT] momentarily to turn the preamp ON or OFF.
•“
” appears when the preamp is set to ON.
➥ Push and hold [P.AMP/ATT] for 1 sec. to turn the
attenuator ON.
• Push [P.AMP/ATT] momentarily to turn the attenuator
OFF.
•“
” appears when the attenuator is set to ON.
• Auto notch filter (p. 80)
➥ Push [ANF/• REC] to turn the auto notch filter ON
and OFF.
•“
• DSP noise reduction (p. 79)
➥ Push [NR/LEV] to turn the DSP noise reduction
ON and OFF.
•“
” appears when the DSP noise reduction is set to
ON.
➥ Push and hold [NR/LEV] for 1 sec. to enter the
noise reduction level set mode, then rotate [DIAL]
to adjust the DSP noise reduction level.
• VSC (voice squelch control) (p. 82)
S-1” is selected, push [F-4 VSC] to turn
➥ While “S
the VSC function ON and OFF.
•“
” appears when VSC function is set to ON.
” appears when the auto notch filter is set to ON.
D Convenient functions for transmit
• VOX (voice operated transmit) (p. 83)
M-3” is selected, push [F-1 VOX] to turn
➥ While “M
the VOX function ON and OFF.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
• “VOX” appears when the VOX function is set to ON.
M-3” is selected, push [F-1 VOX ] for 1
➥ While “M
sec. to enter the VOX set mode.
• Push [F-1 ≤]/[F-2 ≥] to select an item.
• Rotate [DIAL] to set the value/conditions.
59
• Transmit quality monitor (p. 87)
➥ Push [AF(SET)], then [F-4 OTH] to enter the miscellaneous (others) set mode. Select an item with
[F-1 ≤]/[F-2 ≥], then rotate [DIAL] to turn the
monitor function ON and OFF.
RECEIVE AND TRANSMIT
4
D Tone squelch operation
Tone squelch operation is a method of communications using selective calling. Only received signals
having a matching tone will open the squelch. Before
communicating using tone squelch, all members of
your party must agree on the tone squelch frequency.
q Push [MODE] one or more times to select FM
mode.
w Select M-3.
[MENU/GRP] [F-1] [F-3]
[DIAL]
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push [F-3 TON] momentarily several times to turn
the tone squelch function ON.
•“
” appears.
r Push and hold [F-3 TON] for 1 sec. to enter the FM
tone set mode.
4
• The selected tone frequency for TSQL appears.
• Other tone functions can be set by pushing [F-1 TON].
t Rotate [DIAL] to set the desired subaudible tone
frequency.
• See table at right for available tone frequencies.
• Push and hold [F-3 DEF] for 1 sec. to select the default frequency.
Z(MENU/GRP)] to exit the FM tone set mode.
• Push [Z
y Communicate in the usual manner.
• Push and hold [PTT] to transmit; release [PTT] to receive.
• Available tone squelch frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
085.4
088.5
091.5
094.8
097.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
(Unit: Hz)
210.7 254.1
218.1
225.7
229.1
233.6
241.8
250.3
60
4
RECEIVE AND TRANSMIT
D DTCS operation
DTCS function is an another method of communications using selective calling. Only received signals
having a matching 3-digit code will open the squelch.
q Push [MODE] one or more times to select FM
mode.
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
[MENU/GRP]
[F-3]
[F-4]
[DIAL]
e Push [F-3 TON] once or twice to turn the DTCS
function ON.
•“
” appears.
r Push and hold [F-3 TON] for 1 sec. to enter the FM
tone set mode.
• The selected DTCS code appears.
• Other tone functions can be set by pushing [F-1 TON].
t Rotate [DIAL] to set the desired DTCS code and
push [F-4 POL] several times to select the desired
code polarity.
NN : Normal polarity is used for both transmit and
receive.
NR : Normal polarity is used for transmit, reversed polarity is used for receive.
RN : Reversed polarity is used for transmit, normal polarity is used for receive.
RR : Reversed polarity is used for both transmit
and receive.
• Push and hold [F-3 DEF] for 1 sec. to select the default code and polarity.
Z(MENU/GRP)] to exit the FM tone set mode.
• Push [Z
y Communicate in the usual manner.
• Push and hold [PTT] to transmit; release [PTT] to receive.
61
• Available tone codes
023
025
026
031
032
036
043
047
051
053
054
065
071
072
073
074
114
115
116
122
125
131
132
134
143
145
152
155
156
162
165
172
174
205
212
223
225
226
243
244
245
246
251
252
255
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
462
464
465
466
503
506
516
523
526
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
RECEIVE AND TRANSMIT
4
D Tone scan operation
By monitoring a signal that is being transmitted on a
repeater input frequency, you can determine the tone
frequency necessary to access a repeater.
q During tone squelch, DTCS squelch or repeater
operation (“
,” “
played), select M-3.
” or “
” is dis-
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
[MENU/GRP] [F-2] [F-3]
w Push and hold [F-3 TON] for 1 sec. to enter the FM
tone set mode.
e Push [F-2 SCN] to toggle the tone scan operation
ON and OFF.
• When a matched tone or code is detected, tone scan
automatically stops, the matched tone or code is displayed and the tone or code setting is automatically adjusted accordingly.
4
Z(MENU/GRP)] to exit the FM tone set mode.
r Push [Z
During tone squelch operation.
During DTCS squelch operation.
During repeater operation.
62
4
RECEIVE AND TRANSMIT
■ Repeater operation
A repeater amplifies received signals and retransmits
them at a different frequency. When using a repeater,
the transmit frequency is shifted from the receive frequency by an offset frequency. A repeater can be accessed using split frequency operation with the shift
frequency set to the repeater’s offset frequency.
For accessing a repeater which requires a repeater
tone, set the repeater tone frequency in the FM tone
set mode as described on the next page.
• To set the transceiver for repeater operation, follow
the steps q to e to select VFO mode, desired band,
FM mode.
q Push [F-4 V/M] to select VFO mode.
• Push and hold [MENU/GRP] for 1 sec. once or twice to
select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-2.
w Push [ Y(BAND)]/[ Z(BAND)] to select the desired
band or push a band key on the HM-151.
e Push [MODE] momentarily or push and hold for 1
sec. to select FM mode.
• After FM, WFM or AM mode is selected, push [MODE]
for 1 sec. to select from FM, WFM and AM modes.
[MENU/GRP] [F-2] [F-3]
[DIAL]
“TONE” appears.
“DUP–” or “DUP+”
appears.
r Rotate [DIAL] to set the receive frequency (repeater
output frequency).
t Select M-3.
y Push [F-2 DUP] once or twice to set the offset direction.
•“
” or “
” appears.
• The default repeater offsets are the standard values of
0.1000 MHz for HF, 0.500 MHz for 50MHz, 0.600 MHz
for 144 MHz, and 5.000 MHz for 430 MHz. The offset
can be adjusted in set mode. (pgs. 129, 130)
• The transmit frequency can be monitored while pushing
and holding [F-4 XFC] in the M-1 display.
u Push [F-3 TON] to turn the repeater tone ON.
Shifted frequency
and mode appear.
•“
” appears.
• The tone frequency can be set in the FM tone set mode
as described on the next page.
i Communicate in the usual manner.
• Push and hold [PTT] to transmit; release [PTT] to receive.
D One-touch repeater function
This function allows you to set repeater operation by
pushing one key.
➥ To set the transceiver for repeater operation using
the one-touch repeater function, follow the steps q
toANTt as above, then push and hold [F-2 DUP] for
:
0
BW 15k SFT
1
12:00
1 sec.
FM
FIL2
TONE
VFO
•METER
Push and hold [F-2 DUP] for 1 sec. again to exit the rePo
14.100.00
1
peater operating
condition. USB
P.AMP
1
SPLIT
TX
VFO
FM
FIL2
TONE
Set
the offset shift direction and frequency in adATT
OFF
14.100.00
1
vance
(p. 130)
as
well as USB
the tone frequency (see
p. 64).
63
[F-2]
RECEIVE AND TRANSMIT
4
D Repeater tone frequency
Some repeaters require subaudible tones to be accessed. Subaudible tones are superimposed over
your normal signal and must be set in advance. The
transceiver has 50 tones from 67.0 Hz to 254.1 Hz.
Each memory channel can store a different subaudible tone frequency.
[MENU/GRP] [F-1] [F-3]
q Select M-3.
[DIAL]
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
w Push [F-3 TON] once or twice to turn the tone encoder ON.
• “TONE” appears.
e Push and hold [F-3 TON] for 1 sec. to enter the FM
tone set mode.
4
• The selected tone frequency appears.
• Other tone functions can be set by pushing [F-1 TON].
r Rotate [DIAL] to set the desired subaudible tone
frequency.
• See table at right for available tone frequencies.
Z(MENU/GRP)] to exit the FM tone set mode.
t Push [Z
CONVENIENT
Store repeater tone frequencies and ON/OFF settings
in memory channels for easy recall. The transceiver’s
repeater tone frequency is set to 88.5 Hz by default.
This can be changed if desired.
• Available tone squelch frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
085.4
088.5
091.5
094.8
097.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
(Unit: Hz)
210.7 254.1
218.1
225.7
229.1
233.6
241.8
250.3
64
4
RECEIVE AND TRANSMIT
D Transmit frequency monitor check
You may be able to receive the other party’s transmit
signal directly (called ‘listening on the repeater input’)
without having to go through a repeater.
Transmit frequency monitor check (XFC) allows you
to check this.
[MENU/GRP]
[F-4]
SPCH
/LOCK
q Select M-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-1.
1.8
10
21
w While receiving, push and hold [F-4 XFC] to see if
you can receive the other party’s transmit signal directly.
50
1
4
7
.
3.5
14
24
TUNER
/CALL
MW
F-1
F-2
2
5
8
144
0
• While holding [F-4 XFC], the offset direction and frequency are displayed above the multi-function key indicator.
7
18
28
XFC
XFC
V/M
3
MODE
6
FIL
9
GENE
430
CE
F-INP
ENT
HM-151
D Auto repeater function (USA version only)
This function automatically activates the repeater settings (DUP– or DUP+ and/or tone encoder ON/OFF)
when the operating frequency falls within the general
repeater output frequency range and deactivates
them when outside of the range.
Set the auto repeater function ON-1 (auto duplex setting) or ON-2 (auto duplex setting and activating tone
encoder) in the miscellaneous (others) set mode in
advance (p. 130). When ON-1 or ON-2 are turned on,
repeater settings are automatically activated according to the table below right.
[AF]
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
ON-1 sets the duplex setting and ON-2 sets the duplex setting and tone encoder automatically.
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-4 OTH] to enter the miscellaneous (others) set mode.
Auto Re e Push [F-1 ≤] or [F-2 ≥] to select “A
peater.”
r Rotate [DIAL] to select the desired auto repeater
condition from ON-1, ON-2 and OFF.
• Push [F-4 DEF] for 1 sec. to return to default setting.
Z(MENU/GRP)] twice to return to the normal
t Push [Z
operating mode.
65
• Frequency range and offset direction (for USA)
FREQUENCY RANGE
51.620–51.999999 MHz
52.500–52.999999 MHz
53.500–53.999999 MHz
145.200–145.499999 MHz
146.610–146.999999 MHz
147.000–147.399999 MHz
442.000–444.999999 MHz
447.000–449.999999 MHz
DUPLEX DIRECTION
minus duplex
minus duplex
plus duplex
plus duplex
minus duplex
RECEIVE AND TRANSMIT
4
D Storing a non standard repeater
Set the frequency.
Select
[F-1]
[MENU/GRP] [F-2] [F-3] [F-4]
Set the frequency.
[DIAL]
q Turn the auto repeater function OFF in the miscellaneous (others) set mode. (p. 130)
w Push [MODE] to select FM mode.
e Select M-2.
Select
Appears
SPL
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-2.
r Push [F-4 V/M] to select VFO mode.
t Select M-1, then push [F-2 A/B] to select VFO A.
y Rotate [DIAL] to set the receive frequency (repeater output frequency).
u Push [F-2 A/B] to select VFO B.
i Rotate [DIAL] to set the transmit frequency (repeater input frequency).
o Push [F-2 A/B] to select VFO A.
!0 Push [F-1 SPL] to turn the split function ON.
•“
Push
4
Appears
Selected M3, then
TON
push
” appears.
!1 Select M-3, then push [F-3 TON ] to turn on the
previously set tone encoder ON. (p. 64)
!2 Rotate [M-ch] to select the desired memory channel.
•“
Rotate
” appears when the blank channel is selected.
!3 Select M-2, then push and hold [F-2 MW] for 1 sec.
to store the contents in the selected memory channel.
Select
Selected M2, then
MW
push
66
4
RECEIVE AND TRANSMIT
■ 1750 Hz tone burst
A 1750 Hz tone is required to access most European
repeaters.
➥ While pushing and holding [PTT], push [F-3 TON]
in the M-1 display during repeater operation.
(pgs. 63, 66)
Popup indication
appears.
[MENU/GRP]
NOTE: This function is not available for non-European versions.
[F-3]
■ DTMF memory encoder
DTMF tones are used for autopatching, controlling
other equipment, etc. The transceiver has 4 DTMF
memory channels (D1–D4) for storage of often-used
DTMF codes sequence of up to 24 digits.
D DTMF send menu
To transmit a DTMF code using a DTMF send menu,
program the desired code in advance as described on
next page.
• Transmitting
q Select FM mode with [MODE].
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
[MODE]
e Push [F-2 DTM] to enter the DTMF send menu.
• If the DTMF root menu appears, push [F-1 SND]. The
DTMF starting menu can be changed in the miscellaneous (others) set mode (see p. 134).
[MENU/GRP]
r Push [F-1 D1] — [F-4 D4] to transmit the DTMF
code.
[F-1]
[F-2] [F-3] [F-4]
D1”– “D
D4” are highlighted while transmitting.
• “D
• Set the DTMF speed from 100–500 msec. (100 msec.
steps). See next page for DTMF set mode.
• DTMF send menu
Z(MENU/GRP)] twice to exit DTMF send
t Push [Z
menu and return to the normal FM mode display.
DTMF code
sequence
67
RECEIVE AND TRANSMIT
4
D Programming a DTMF code
q Push [MODE] to select FM mode.
w Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1.
Z(MENU/GRP)] to select the
e Push [F-2 DTM] then [Z
DTMF root menu.
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
[DIAL]
• If the DTMF root menu appears, skip pushing
Z(MENU/GRP)]. The DTMF starting menu can be
[Z
changed in the miscellaneous (others) set mode. (see
p. 134)
r Push [F-2 EDT] to enter the DTMF edit menu.
t Push [F-1 D1 ] — [F-4 D4 ] to select the desired
DTMF memory channel.
y Select the desired code by rotating [DIAL].
• Push [F-1 Å] or [F-2 Ç] for cursor movement.
• Push [F-3 DEL] to delete the selected code.
u Repeat steps t and y until the desired contents
are input.
Z(MENU/GRP)] to return to memory channel
i Push [Z
selection mode, then select the next memory channel and repeat steps t and u for code input, if desired.
Z(MENU/GRP)] twice to exit the keyer edit
o Push [Z
mode.
4
DTMF memory channel select
Selected
code
D DTMF speed
The rate at which DTMF memories send individual
DTMF characters can be set to accommodate operating needs.
q Select the DTMF root menu as described above.
w Push [F-4 SET] to enter the DTMF set mode.
e Rotate [DIAL] to set the desired DTMF speed.
• Four rates are available: “100 ms” is the fastest; “500
ms” is slowest.
• Push and hold [F-4 DEF] for 1 sec. to select the default rate.
Z(MENU/GRP)] twice to exit the DTMF set
r Push [Z
mode and return to the normal FM mode display.
68
5
FUNCTIONS FOR RECEIVE
■ Simple band scope
This DSP-based simple band scope allows you to display conditions on the selected band, as well as relative strength of signals. The IC-7000 has two modes
for the spectrum indication—one is fix mode, and another one is center mode.
NOTE: The IC-7000’s simple band scope can
monitor the displayed frequency during sweeping.
Both the receving and sweeping functions use the
same receive circuits which must switch at high
speed. This switching sound may be irritating to listen to. If so, set the desired monitoring sound,
FAST Sweep Sound ,” or change the fast
“F
FAST Sweep,” in the scope set
sweep setting, “F
mode (p. 72).
Quick entry
Y(BAND)] for 1 sec. to turn the
➥ Push and hold [Y
simple band scope ON and OFF.
Z(MENU/GRP)] also to turn OFF.
• Push [Z
[Y]
69
[MENU/GRP]
➥ Select G-1 (Scope).
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group G (Graphic).
• Push [MENU/GRP] momentarily one or more times to
select the menu G-1 (Scope).
FUNCTIONS FOR RECEIVE
5
D Fix mode
Displays signals within the specified frequency range.
The selected band conditions can be observed at a
glance when using this mode.
q Set a mode and frequency.
w Select G-1 (Scope).
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group G (Graphic).
• Push [MENU/GRP] momentarily one or more times to
select the menu G-1 (Scope).
[F-1]
[MENU/GRP]
[F-2] [F-3] [F-4]
e Push [F-3 FIX ] momentarily to select the fix
mode.
• “O” and readout frequency indicator appear when the
fix mode is selected.
r Push [F-4 SPD] momentarily to select the sweep
speed.
• “≈” or “≈≈” appears when Slow speed or Fast speed is
selected, respectively.
t Push [F-1 SPN] one or more times to select the
desired steps.
• ±10, 25, 50, 100 and 250 kHz are available.
• Push and hold [F-1 SPN] for 1 sec. to select the ±10
kHz step.
<” or “>
>” indicates when the displayed frequency is out
• “<
of range. The scope center position can be set to the
displayed frequency by pushing and holding [F-3
FIX] for 1 sec.
• The simple band scope operates in the peak level hold
mode. Peak levels are displayed in the background of
the current spectrum in a different color until the receive
frequency changes. This can be cleared by pushing
and holding [F-2 HLD] for 1 sec., or deactivated in the
scope set mode. (p. 72)
NOTE: If there is a lot of signal noise, turn the preamp OFF and the attenuator ON (p. 72) to reduce
the input level and improve the readability of the
scope.
5
y Push [F-2 HLD] to freeze the current spectrum display.
• “H” appears while the function is in use.
70
5
FUNCTIONS FOR RECEIVE
D Center mode
Displays signals around the displayed frequency
within the selected span. The set frequency is always
displayed at the center of the screen.
q Set a mode and frequency.
w Select G-1 (Scope).
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group G (Graphic).
• Push [MENU/GRP] momentarily one or more times to
select the menu G-1 (Scope).
[F-1]
[MENU/GRP]
[F-2] [F-3] [F-4]
e Push [F-3 FIX] momentarily to select the center
mode.
• “= ” appears when the center mode is selected.
r Push [F-4 SPD] momentarily to select the sweep
speed.
• “≈” or “≈≈” appears when Slow speed or Fast speed is
selected, respectively.
t Push [F-1 SPN] one or more times to select the
desired steps.
• ±10, 25, 50, 100 and 250 kHz are available.
• Push and hold [F-1 SPN] for 1 sec. to select the ±10
kHz step.
• The simple band scope operates in the peak level hold
mode. Peak levels are displayed in the background of
the current spectrum in a different color until the receive
frequency changes. This can be cleared by pushing
and holding [F-2 HLD] for 1 sec., or deactivated in the
scope set mode. (p. 72)
NOTE: If there is a lot of signal noise, turn the preamp OFF and the attenuator ON (p. 72) to reduce
the input level and improve the readability of the
scope.
y Push [F-2 HLD] to freeze the current spectrum display and range.
• “H ” and readout frequency indicator appear while the
function is in use.
D Scope set mode
This set mode is used to set the peak hold function
and scope size setting.
q Select G-1 (Scope).
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group G (Graphic).
• Push [MENU/GRP] momentarily one or more times to
select the menu G-1 (Scope).
w Push and hold [F-4 SPD] for 1 sec. to enter the
scope set mode.
e Push [F-1 ≤] or [F-2 ≥] to select the desired set
item.
r Set the desired condition using [DIAL].
• Push [F-4 DEF] for 1 sec. to select a default condition.
Z(MENU/GRP)] to exit from set mode.
t Push [Z
71
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
FUNCTIONS FOR RECEIVE
5
Scope set mode (Continued)
1 Max Hold
This item turns the peak level holding function ON
and OFF.
2 Scope Size
This item toggles the scope size setting between normal and wide.
ON
OFF
Peak hold is turned ON.
(default)
Peak hold is turned OFF.
Normal
Wide
Normal size is selected.
(default)
Wide size is selected.
Continuous
1 Sweep
3 FAST Sweep
This item selects the sweep speed setting.
Push [F-4 SPD] momentar- One Fast speed sweep ocily to toggle the sweep curs each time [F-4 SPD] is
speed Fast and Slow contin- pushed momentarily.
uously. (default)
5
4 FAST Sweep Sound
This item sets the monitoring sound level for fast
sweeping.
-10dB : Monitoring sound is set 10 dB smaller than
normal sound. (default)
0dB
: Same as normal sound.
OFF
: No sound comes out while fast sweeping.
■ Preamp and attenuator
The preamp amplifies received signals in the receiver
input (front end) circuit to improve the S/N ratio and
sensitivity. Turn this function ON when receiving weak
signals.
[P.AMP/ATT]
“
” or “
” appears.
The attenuator prevents a strong undesired signal
near the desired frequency or near your location,
such as from a broadcast station, from causing distortion or spurious signals.
Push [P.AMP/ATT] momentarily to turn the preamp
ON and OFF; push and hold for 1 sec. to turn the attenuator ON.
•“
” appears when the preamp is ON; “
” appears when the 12 dB attenuator is ON.
• Only one of these functions can be activated at a time.
momentarily
momentarily
1 sec.
72
5
FUNCTIONS FOR RECEIVE
■ RIT function
The RIT (Receive Incremental Tuning) function compensates for stations transmitting off-frequency.
The function shifts the receive frequency up to ±9.999
kHz in 1 Hz steps (10 Hz steps when cancelling the 1
Hz step readout) without moving the transmit frequency.
[PBT/M-ch/RIT] switch
[RIT] (outer)
[PBT/M-ch/RIT] indicator
q Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
[MENU/GRP] [F-1] [F-3]
w Push and hold [PBT/M-ch/RIT] for 1 sec. to enter
the RIT/∂TX mode.
e Push [F-1 RIT] to turn the RIT function ON.
•“
” indicator and the frequency shift appear and
[PBT/M-ch/RIT] indicator lights orange when the function is ON.
Push
for 1sec.
r Rotate
[RIT] (outer) control to compensate for offRIT
frequency stations.
• The transmit frequency is not shifted.
t To reset the RIT frequency, push and hold [F-3
CLR] for 1 sec.
Push
• Push [F-3 CLR ] momentarily to reset the RIT freQuick RIT/∂TX Clear ” in the
quency when “Q
miscellaneous (others) set mode is ON. (p. 133)
y To cancel the RIT function, push [F-1 RIT] momentarily again.
•“
Rotate
” indicator disappears.
Z(MENU/GRP)] to exit the RIT/∂TX mode.
u Push [Z
Appear
When RIT and ∂TX are ON at the same time, the
RIT
[RIT] (outer) control shifts both the transmit and receive frequencies from the displayed frequency at
the same time.
Push
Reset to
“0.00k”
• Calculate function
• Practical example
The shift frequency of the RIT (or ∂TX) function can
be added/subtracted to the displayed frequency.
When you find a DX station on 21.025 MHz/CW and
the station is picking up stations transmitting slightly
up from 21.025 MHz.
While displaying the RIT (and/or ∂TX) shift frequency, push and hold [F-1 RIT] (or [F-2 ∂TX]) for
1 sec.
q Push [F-1 RIT] and [F-2 ∂TX] to turn both the
RIT and ∂TX functions ON.
w Rotate [RIT] (outer) to find the DX station’s receive frequency.
e When you find the DX station’s receive frequency,
push [F-1 RIT] to turn the RIT function OFF.
• Now you can transmit the DX station’s receive frequency and receive on the DX station’s transmit frequency (21.025 MHz).
Push and hold
r Start transmitting when the station stands by for
new callers.
73
ANT
1
BW 2.4k SFT
T X VFO
METER
Po
0
USB
FUNCTIONS FOR RECEIVE
5
■ AGC function
The AGC (auto gain control) controls receiver gain to
produce a constant audio output level even when the
received signal strength is varied by fading, etc.
The FM/WFM modes AGC time constant is fixed as
‘FAST’ (0.1 sec.) and AGC time constant cannot be
selected.
The transceiver has 3 AGC characteristics (time constant; fast, mid, slow) for non-FM/WFM mode.
D AGC time constant selection
q Select non-FM/WFM mode with [MODE].
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push [F-3 AGC] several times to select AGC fast,
AGC medium (MID) AGC slow or AGC OFF.
[MENU/GRP]
[F-3]
•“
,” “
,” “
” or “
” appears when
AGC fast, AGC medium (MID), AGC slow or AGC OFF
is selected, respectively.
“
5
” (OFF) appears when AGC time constant
OFF is set for one of FAST, MID, SLOW setting in
AGC set mode.
D Setting the AGC time constant
q Select the desired mode other than FM/WFM
modes.
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push and hold [F-3 AGC ] for 1 sec. to enter the
AGC set mode.
r Push one of [F-2 FAST], [F-3 MID], [F-4 SLOW]
to select the desired AGC time constant.
t Rotate [DIAL] to set the desired time constant.
• AGC time constants can be selected between 0.1 to
8.0 sec. (depends on mode) or turned OFF.
• Push and hold [F-2 FAST], [F-3 MID] or [F-4 SLOW]
for 1 sec. to select a default value each for fast, mid.
and slow, respectively.
y Select another mode other than FM/WFM. Repeat
steps r and t, if desired.
• See table to the right for available time constants.
Z(MENU/GRP)] to exit the AGC set mode.
u Push [Z
[MENU/GRP] [F-2] [F-3] [F-4]
[DIAL]
• Selectable AGC time constant (unit: sec.)
Mode
Default
Selectable AGC time constant
SSB
0.3 (FAST)
OFF, 0.1, 0.2, 0.3, 0.5, 0.8, 1.2,
2.0 (MID)
1.6, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0
6.0 (SLOW)
CW
0.1 (FAST)
OFF, 0.1, 0.2, 0.3, 0.5, 0.8, 1.2,
0.5 (MID)
1.6, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0
1.2 (SLOW)
0.1 (FAST)
OFF, 0.1, 0.2, 0.3, 0.5, 0.8, 1.2,
RTTY 0.5 (MID)
1.6, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0
1.2 (SLOW)
AM
3.0 (FAST)
OFF, 0.3, 0.5, 0.8, 1.2, 1.6, 2.0,
5.0 (MID)
2.5, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0
7.0 (SLOW)
FM/WFM 0.1 (FAST)
Fixed
74
5
FUNCTIONS FOR RECEIVE
■ IF filter selection
The transceiver has 3 passband IF filter widths for
each mode.
For FM mode, the passband width is fixed and 3 passband widths are available.
For SSB and CW modes, the passband width can be
set from 50 to 3600 Hz in 50 or 100 Hz steps. A total of
41 passband widths are available.
For WFM mode, the passband width is fixed at 280
kHz.
For RTTY mode, the passband width can be set from
50 to 2700 Hz in 50 or 100 Hz steps. A total of 32
passband widths are available.
The filter selection is automatically memorized in
each mode.
The PBT shift frequencies are automatically memorized in each filter.
For AM mode, the passband width can be set from 200
Hz to 10 kHz in 200 Hz steps. A total of 50 passband
widths are available.
D IF filter selection
Selected IF filter
[MENU/GRP]
[F-3]
q Select the desired mode.
w Select M-1.
Passband
width
Shift
frequency
Popup indicator appears
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-1.
e Push [F-3 FIL] momentarily several times to select the IF filter 1, 2 or 3.
• The selected filter number is displayed in the LCD.
• The filter setting window appears and shows the selected passband width and shift frequency. (The filter
setting window can be turned OFF in the display set
mode. (p. 125)
The IF filter for WFM mode is fixed and cannot be
changed.
75
SPCH
/LOCK
1.8
10
21
50
1
4
7
.
3.5
14
24
TUNER
/CALL
2
5
8
144
0
XFC
V/M
MW
F-1
F-2
7
18
28
3
MODE
FIL
6
FIL
9
GENE
430
CE
F-INP
ENT
HM-151
FUNCTIONS FOR RECEIVE
5
D FIlter passband width setting (SSB/CW/RTTY/AM only)
q Select SSB, CW, RTTY or AM mode.
• Passband widths for FM and WFM modes are fixed
and cannot be set.
w Select M-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-1.
[MENU/GRP] [F-1] [F-2] [F-3]
[DIAL]
e Push [F-3 FIL] for 1 sec. to enter filter set mode.
Selected IF filter
Mode
SSB
Passband
width
Shift
frequency
CW
RTTY
r Push [F-3 FIL] several times to select the desired
IF filter.
t While pushing and holding [F-1 BW], rotate [DIAL]
to set the desired passband width.
AM
• The passband width can be set within the range as
shown in the table to the right.
• Push [F-2 DEF] for 1 sec. to select the default value.
FM*
y Repeat steps r to t if desired.
Z(MENU/GRP)] to exit the filter set mode.
u Push [Z
The PBT shift frequencies are cleared when the
passband width is changed.
This filter set mode screen graphically displays the
PBT shift frequencies.
WFM
Filter
Default
FIL1
FIL2
FIL3
FIL1
FIL2
FIL3
FIL1
FIL2
FIL3
FIL1
FIL2
FIL3
FIL1
FIL2
FIL3
3.0 kHz
50–500 Hz (50 Hz)/
2.4 kHz
600–3.6 kHz (100 Hz)
1.8 kHz
1.2 kHz
50–500 Hz (50 Hz)/
500 Hz
600–3.6 kHz (100 Hz)
250 Hz
2.4 kHz
50–500 Hz (50 Hz)/
500 Hz
600–2.7 kHz (100 Hz)
250 Hz
9.0 kHz
200 Hz–10.0 kHz
6.0 kHz
(200 Hz)
3.0 kHz
15 kHz
10 kHz
Fixed
7.0 kHz
Range (Steps)
FIL
280 kHz
5
Fixed
*: When the IF filter is selected FIL2 or FIL3 in the FM
mode operation, the Tx IF filter’s passband width is
fixed narrow selection (2.5 kHz).
D IF fIlter shape (SSB/CW only)
The type of DSP filter shape for each SSB and CW
can be selected independently from soft and sharp.
q Select SSB or CW mode.
w Select M-1.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-1.
e Push [F-3 FIL] for 1 sec. to enter filter set mode.
r Push [F-3 FIL] several times to select the desired
IF filter.
t Push [F-4] to select the filter shape from “SHARP”
and “SOFT.”
Z(MENU/GRP)] to exit the filter set mode.
y Push [Z
[MENU/GRP]
[F-3] [F-4]
Push
Specified selectivity (p. 148) is measured with this
parameter set to SHARP.
76
5
FUNCTIONS FOR RECEIVE
■ Twin PBT operation
The general PBT (Passband Tuning) function electronically narrows the IF passband width by shifting the
IF frequency slightly outside of the IF filter passband
to reject interference. This transceiver uses the DSP
circuit for the PBT function. Moving both [PBT/M-ch/RIT]
controls to the same position shifts the IF.
[PBT/M-ch/RIT(CLR)] switch/[PBT] (inner) control
[PBT/M-ch/RIT] indicator
➥ Push [PBT/M-ch/RIT] momentarily to select the
twin PBT function, if the M-ch-RIT is selected.
[F-3]
[PBT] (outer) control [MENU/GRP]
• [PBT/M-ch/RIT] indicator (Green) lights.
• The passband settings window shows the passband
width and shift frequency graphically. (The passband
settings window can be turned OFF in the display set
mode. p. 125)
Dot indicator appears
when PBT is activate
➥ When M-1 is selected, push and hold [F-3 FIL] for
1 sec. to enter the filter set mode. Current passband
width and shift frequency is displayed in the filter set
mode.
➥ To set the [PBT/M-ch/RIT] controls to the center positions, push and hold [PBT/M-ch/RIT(CLR)] for 1 sec.
Selected IF filter
Passband
width
The limit of the variable range depends on the passband width and mode. The limit of the variable range is
half of the passband width, and PBT is adjustable in
100 (AM) or 25 Hz steps (other modes).
Shift
frequency
Popup indicator appears
• [PBT] controls should normally be set to the center positions (PBT setting is cleared) when there is no interference.
• When PBT is used, the audio tone may be changed.
• Not available for FM or WFM modes.
• While rotating [PBT], noise may occur. This comes from
the DSP unit and does not indicate an equipment malfunction.
PBT OPERATION EXAMPLE
Both controls at
center position
Cutting the lower
passband
Passband
IF center frequency
77
Interference
Desired signal
Cutting both higher and
lower passbands
Passband
Interference
Interference
Desired signal
FUNCTIONS FOR RECEIVE
5
■ Noise blanker
The noise blanker eliminates pulse-type noise such
as from car ignitions. The noise blanker is not available for WFM mode.
Appears [NB/ADJ]
➥ Push [NB/ADJ] momentarily to toggle the noise
blanker ON and OFF.
•“
” indicator appears when the NB function is ON.
When using the noise blanker, received signals
may be distorted if they are excessively strong or
the noise type is other than impulse. Nearby strong
signals can also cause the noise blanker to create
distortion. Turn the noise blanker function OFF, or
adjust the noise blanker level to a shallower setting
(see below) in this case.
D Noise blanker set mode
q Push and hold [NB/ADJ] for 1 sec. to enter the
noise blanker set mode.
w Push [F-1 ≤] or [F-2 ≥] to select the desired set
item.
e Rotate [DIAL] to adjust the desired condition.
5
[NB/ADJ]
• Push [F-4 DEF] for 1 sec. to return to default value.
Z(MENU/GRP)]) to exit the
r Push [NB/ADJ] (or push [Z
noise blanker set mode.
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
1. NB Level
This item adjusts the noise blanker level. The noise
blanker level can be adjusted from 0 to 100%.
50%
50% (default)
2. NB Width
This item adjusts the noise blanker width. The noise
blanker width can be adjusted from 1 to 100.
50
50 (default)
78
5
FUNCTIONS FOR RECEIVE
■ Noise reduction
The noise reduction function enhances desired signals in the presence of noise by using the DSP circuit. The amount of enhancement is adjustable.
➥ Push [NR/LEV] momentarily to toggle the noise reduction ON and OFF.
•“
” indicator appears when the NR function is ON.
The noise reduction level can result in audio signal
masking. Set the noise reduction level for maximum readability as described below.
Appears
[MENU/GRP] [F-4] [NR/LEV]
Noise reduction OFF
NR NR Level
Noise reduction activated
0
NR NR Level
Noise components
q Push [NR/LEV] for 1 sec. to enter the noise reduction level set mode.
w Rotate [DIAL] to adjust the noise reduction level.
• Set the noise reduction level 0 to 15.
• Push [F-4 DEF] for 1 sec. to return to default level.
Z(MENU/GRP)]) to exit the
e Push [NR/LEV] (or push [Z
noise reduction level set mode.
NR Level
79
5
Desired
signal (CW)
D Noise reduction set mode
This item adjusts the noise reduction level. The noise
reduction level can be adjusted from 0 to 15.
[DIAL]
4
4 (default)
FUNCTIONS FOR RECEIVE
5
■ Notch function
This transceiver has auto and manual notch functions. The auto notch function automatically attenuates up to 3 beat tones, tuning signals, etc., even if
they are moving. The manual notch can be set to attenuate a frequency via the manual notch filter set
mode.
➥ While in SSB and AM modes, push [ANF/•REC] or
[MNF/ADJ] to toggle the notch function between
auto, manual and OFF.
• Both of the auto and manual notch functions can be activated at the same time.
➥ While in CW and RTTY modes, push [MNF/ADJ]
to toggle the manual notch function ON and OFF.
➥ While in FM mode, push [ANF/• REC] to toggle the
auto notch function ON and OFF.
•“
” appears when auto notch function is in use.
•“
” appears when manual notch function is in use.
• Manual notch filter settings are described on the next
page.
D Auto notch function
The auto notch can be used in SSB, AM and FM
modes.
➥ Push [ANF/• REC] momentarily to turn the automatic notch function ON and OFF.
•“
5
” appears when auto notch function is in use.
Auto notch OFF
Appears
Auto notch ON
Desired
signal (AF)
Unwanted interference
[ANF/•REC]
Desired
signal (AF)
Interference frequency
is attenuated
80
5
FUNCTIONS FOR RECEIVE
D Manual notch function
The manual notch function can be used in SSB, CW,
RTTY and AM modes.
➥ Push [MNF/ADJ] momentarily to turn the manual
notch function ON and OFF.
•“
” appears when manual notch function is in use.
• Set the frequency for manual notch filtering via the
manual notch filter set mode. (shown below)
NF1” and
• Even when both of the manual notch filters, “N
NF2 ,” are set to OFF in the manual notch filter set
“N
NF1” is automatically turned ON if the manual
mode, “N
notch function is ON.
Appears
[MNF/ADJ]
D Manual notch filter set mode
q Push [MNF/ADJ] for 1 sec. to enter the manual
notch filter set mode.
w Push [F-2 NF1] or [F-3 NF2] to select the desired
filter ON and OFF.
e Rotate [DIAL] to adjust the selected filter frequency.
[MNF/ADJ]
• Push [F-4 NW] to toggle the filter width from narrow,
middle and wide.
Z(MENU/GRP)]) to exit
r Push [MNF/ADJ] (or push [Z
the manual notch filter set mode.
[MENU/GRP] [F-2] [F-3] [F-4]
[DIAL]
While adjusting the manual notch filter, noise may
be heard. This comes from the DSP unit and does
not indicate an equipment malfunction.
81
FUNCTIONS FOR RECEIVE
5
■ Voice squelch control function
This function is useful when you don't want to hear
unmodulated signals. When the voice squelch control
function is activated, the transceiver checks received
signals for voice components.
If a receiver signal includes voice components, and
the tone of the voice components changes within 1
sec., squelch opens. If the received signal includes
no voice components or the tone of the voice components does not change within 1 sec., squelch closes.
Appears
[MENU/GRP]
[F-4]
q Select S-1 or S-2.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group S.
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1 or S-2.
w Push [F-4 VSC] to turn the VSC (Voice Squelch
Control) function ON.
•“
” appears when the function is activated.
5
• The VSC function is available for phone modes
(SSB, AM, FM, WFM).
• The VSC function can also be used for scanning
operation in AM, FM or WFM modes. (p. 112)
■ Meter peak hold function
The S-meter has a peak level holding function. The
peak level of the received signal strength is indicated
for 0.5 sec. (approx). This function can be deactivated
Meter Peak Hold ” ;
in the display set mode (“M
see p. 125) if desired.
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-2 DISP] to enter the display set mode.
Meter Peak
e Push [F-1 ≤] or [F-2 ≥] to select “M
Hold.”
r Rotate [DIAL] to turn the meter peak hold setting
ON and OFF.
• Push [F-4 DEF] for 1 sec. to return to default condition.
[AF]
[MENU/GRP] [F-1] [F-2]
[DIAL]
[EXAMPLE]:
S 1
3
5
7
9
20
40
60dB
Initial reception of a
signal results in an
S-meter reading of
40 dB.
S 1
3
5
7
9
20
40
60dB
The highest indicated bar remains displayed for about 0.5
sec. even when the
signal strength decreases.
Z(MENU/GRP)] twice to return to normal opt Push [Z
erating mode.
82
6
FUNCTIONS FOR TRANSMIT
■ VOX function
The VOX (Voice-Operated Transmission) function
switches between transmit and receive with your
voice. This function provides an opportunity for
hands-free operation or to input log entries into your
computer, etc., while operating.
q Select a phone mode (SSB, AM, FM) with [MODE].
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
Appears
[MENU/GRP]
[F-1]
e Push [F-1 VOX ] to toggle the VOX function ON
and OFF.
•“
” appears while the VOX is in use.
The VOX gain, ANTI-VOX and VOX delay can be set in
VOX set mode.
D Adjusting the VOX function
q Select a phone mode (SSB, AM, FM).
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
[MENU/GRP] [F-1] [F-2]
[DIAL]
e Push and hold [F-1 VOX] for 1 sec. to enter the
VOX set mode.
r Select the VOX gain item using [F-1 ≤] or [F-2 ≥].
t While speaking into the microphone, rotate [DIAL]
to the point where the transceiver is continuously
transmitting.
y Adjust the VOX delay for a convenient interval before returning to receive.
- Select the VOX delay item using [F-1 ≤] or [F-2 ≥].
- Rotate [DIAL].
u If the receive audio from the speaker causes the
VOX circuit to switch to, adjust the anti-VOX setting to the point where speaker audio does not activate the VOX.
83
FUNCTIONS FOR TRANSMIT
6
D VOX set mode
1. VOX Gain
This item adjusts the VOX gain for the VOX (voice activated transmit) function. This setting can be adjusted
from 0 to 100% in 1% steps.
50%
50% (default)
• Push [F-4 DEF] for 1 sec. to return to default gain.
2. Anti-VOX
This item adjusts the ANTI-VOX gain for the VOX
(voice activated transmit) function. This setting can be
adjusted from 0 to 100% in 1% steps.
50%
50% (default)
• Push [F-4 DEF] for 1 sec. to return to default gain.
3. VOX Delay
This item adjusts the VOX (Voice-activated Transmit)
delay time. The delay time can be adjusted from 0 to
2.0 sec. in 0.1 sec. steps.
0.2s
0.2 sec. (default)
• Push [F-4 DEF] for 1 sec. to return to default delay time.
6
■ Transmit filter width setting (SSB only)
The transmit filter width for SSB mode can be selected from wide, middle and narrow.
q Select an SSB mode (USB or LSB) with [MODE].
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push and hold [F-4 TBW] for 1 sec. once or twice
to select the desired transmit filter width from narrow, middle and wide.
[MENU/GRP]
[F-4]
• Push [F-4 TBW] momentarily to display the selected TX
filter width.
• The transmit filter width window appears for showing
the selected TX filter width each time [F-4 TBW ] is
pushed.
• The following filters are specified as the default. Each
of the filter widths can be set in the quick set mode.
(pgs. 121, 122)
WIDE : 100 Hz to 2900 Hz
MID : 300 Hz to 2700 Hz
NAR : 500 Hz to 2500 Hz
84
6
FUNCTIONS FOR TRANSMIT
■ Break-in function
The break-in function is used in CW mode to automatically switch the transceiver between transmit and receive when keying. The IC-7000 is capable of full
break-in or semi break-in.
D Semi break-in operation
During semi break-in operation, the transceiver selects transmit when keying, then automatically returns
to receive after a pre-set time from when you stop
keying.
• Semi break-in operation
q Push [MODE] to select CW or CW-R mode.
w Select M-3.
• Break-in delay setting
q Push [MODE] to select CW or CW-R mode.
w Select M-3.
e Push and hold [F-1 BRK] for 1 sec. to enter the
break-in delay time set mode.
r Rotate [DIAL] to set the break-in delay time (the
delay from transmit to receive).
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push [F-1 BRK ] once or twice to turn the semi
break-in function ON.
•“
” appears.
[MENU/GRP]
[F-1]
[DIAL]
Appears
[MENU/GRP]
[F-1]
Key Speed” in the
When using a paddle, set “K
quick set mode to adjust the keying speed. (p. 122)
D Full break-in operation
During full break-in operation, the transceiver automatically switches to receive between keying dots
and dashes so that the operator can hear activity on
the channel when transmitting.
q Push [MODE] to select CW or CW-R mode.
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push [F-1 BRK ] once or twice to turn the semi
break-in function ON.
•“
Appears
[MENU/GRP]
85
[F-1]
” appears.
Key Speed” in the
When using a paddle, set “K
quick set mode to adjust the keying speed. (p. 122)
FUNCTIONS FOR TRANSMIT
6
■ ∂TX function
The ∂TX function shifts the transmit frequency up to
±9.999 kHz in 1 Hz steps (10 Hz steps when cancelling the 1 Hz step readout) without moving the receive frequency.
[PBT/M-ch/RIT] switch
[RIT] (outer)
[PBT/M-ch/RIT] indicator
q Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
w Push and hold [PBT/M-ch/RIT] for 1 sec. to enter
the RIT/∂TX mode.
e Push [F-2 ∂TX] to turn the ∂TX function ON.
[MENU/GRP] [F-2] [F-3]
•“
” indicator and the frequency shift appear and
[PBT/M-ch/RIT] indicator lights orange when the function is ON.
∂TX [RIT] (outer) control to shift the transmitter
r Rotate
frequency.
Push
for 1sec.
• The receive frequency is not shifted.
t To reset the ∂TX frequency, push [F-3 CLR] for
1 sec.
• Push [F-3 CLR ] momentarily to reset the RIT freQuick RIT/∂TX Clear ” in the
quency when “Q
miscellaneous (others) set mode is ON. (p. 133)
Push
y To cancel the ∂TX function, push [F-2 ∂TX] momentarily again.
•“
6
” indicator disappears.
Rotate
Z(MENU/GRP)] to exit the RIT/∂TX mode.
u Push [Z
When
∂TX RIT and ∂TX are ON at the same time,
[RIT] (outer) control shifts both the transmit and receive frequencies from the displayed frequency at
the same time.
Appear
Push
Reset to
“0.00k”
• Calculate function
• Practical example
The frequency shift of the (RIT or) ∂TX function can
be added/subtracted to the displayed frequency.
When you find a DX station on 21.025 MHz/CW and
the station is picking up stations transmitting slightly
up from 21.025 MHz.
While displaying the (RIT and/or) ∂TX shift frequency, push and hold ([F-1 RIT] or) [F-2 ∂TX] for
1 sec.
q Push [F-1 RIT] and [F-2 ∂TX] to turn both the
RIT and ∂TX functions ON.
w Rotate [RIT] (outer) to find the DX station’s receive frequency.
e When you find the DX station’s receive frequency,
push [F-1 RIT] to turn the RIT function OFF.
• Now you can transmit the DX station’s receive frequency and receive the DX station’s transmit frequency (21.025 MHz).
r Start transmitting while the station is standing by.
Push and hold
86
6
FUNCTIONS FOR TRANSMIT
■ Monitor function
The monitor function allows you to monitor your transmitted signals in any mode through the speaker. The
CW side tone functions regardless of the monitor
function setting.
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-4 OTH] to enter the miscellaneous (others) set mode.
Monitor.”
e Push [F-1 ≤] several times to select “M
r Rotate [DIAL] to turn the monitor function ON.
[AF]
[MENU/GRP] [F-1] [F-2] [F-4]
• Push [F-4 DEF] for 1 sec. to return to default condition.
Monitor Level.”
t Push [F-2 ≥] to select “M
y Rotate [DIAL] to adjust the monitor level.
• Push [F-4 DEF] for 1 sec. to return to default level.
Z(MENU/GRP)] twice to return to normal opu Push [Z
erating mode.
Use headphones to prevent feedback.
■ Speech compressor
The IC-7000 has a built-in, low distortion speech compressor circuit. This circuit increases your average
talk power in SSB mode and is especially useful for
DX-ing or noisy condition when the receiving station
is having difficulty copying your signal.
q Select an SSB mode.
w Select M-3.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-3.
e Push [F-2 COM ] momentarily to turn the speech
compressor function ON and OFF.
•“
87
” appears.
Appears
[MENU/GRP]
[F-2]
[DIAL]
FUNCTIONS FOR TRANSMIT
6
D Compression level setting
• Pre-setting the transceiver
• Compression level setting
[AF]
[MENU/GRP] [F-1] [F-2] [F-3]
q Select an SSB mode.
w Turn the speech compressor function OFF, if it’s
ON.
● Select M-1.
• Push and hold [MENU/GRP] for 1 sec. once or
twice to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-1.
● Push [F-2 COM] momentarily to turn the speech
compressor function OFF.
•“
[MENU/GRP] [F-2] [F-3]
[DIAL]
” disappears.
e Select ALC meter.
● Select S-1.
● Push [F-3 MET] one or more times to select the
ALC meter.
• “ALC” appears.
r Adjust the MIC gain.
● Push [AF(SET)] momentarily to enter the set
mode menu.
● Push [F-1 QS] to enter the quick set mode.
MIC Gain.”
● Push [F-1 Y] or [F-2 Z] to select “M
● Push [PTT] (microphone) to transmit at your
normal voice level.
● While speaking into the microphone, rotate
[DIAL] so that the ALC meter reads within the
ALC zone, whether you speak softly or loudly.
● Push [Z(MENU/GRP)] twice to return normal operating mode.
[DIAL]
q Select COMP meter.
● Select S-1.
• Push and hold [MENU/GRP] for 1 sec. once or
twice to select the menu group S.
• Push [MENU/GRP] momentarily one or more times
to select the menu S-1.
● Push [F-3 MET] one or more times to select the
COMP meter.
•“
” appears.
w Turn ON the speech compressor function and
enter the speech compression level set mode.
● Select M-1.
● Push and hold [F-2 COM] for 1 sec. to enter the
speech compression level set mode.
6
• speech compressor function automatically turns ON.
e Rotate [DIAL] so that the COMP meter reads between 10 dB to 20 dB.
Appears
NOTE: When the ALC meter peaks below the ALC
zone, your transmitted voice may be distorted.
ALC
ALC zone
Adjust ‘COMP LEVEL’ so that the ALC meter
peaks above the ALC zone.
COMP Level
This item adjusts the speech compression level. The
speech compression level can be adjusted from 0 to
10.
5
5 (default)
• Push [F-4 DEF] for 1 sec. to return to default level.
88
6
FUNCTIONS FOR TRANSMIT
■ Split frequency operation
Split frequency operation allows you to transmit and
receive in the same mode on two different frequencies.
The split frequency operation is basically performed
using 2 VFO frequencies (VFO A and VFO B) on the
main and sub readouts.
The following is an example of setting 21.290 MHz for
receiving and 21.310 MHz for transmitting.
[MENU/GRP] [F-1] [F-2] [F-4]
q Select VFO A and set the frequency to 21.290 MHz
(USB).
[DIAL]
CONVENIENT
DIRECT SHIFT FREQUENCY INPUT
The shift frequency can be entered directly.
• [F-4 V/M] is available when M-2 appears.
• [F-2 A/B] is available when M-1 appears.
q Push [F-INP/ENT] (HM-151).
w Enter the desired shift frequency with the digit
keys.
• 1 kHz to 1 MHz shifts can be entered.
• When you require a minus shift direction, push [50/•]
before entering the shift.
M-1) on the transceiver’s front
e Push [F-1 SPL ] (M
panel.
w Push [F-1 SPL] momentarily (in the M-1 menu) to
turn the split function ON, then push and hold [F-2
A/B] (M
M-1) for 1 sec.
• The shift frequency is input to the sub readout and the
split function is turned ON.
• The equalized transmit (VFO B) frequency and “
”
appear on the LCD.
• The quick split function is much more convenient for
selecting the transmit frequency. See the next page for
details.
ANT
1
[EXAMPLE]
VFO
To operate on 3 kHz
lower frequency:
F-INP
ENT
:
0
USB
1.8
(SPL)
1
50
HM-151
Transceiver
.
7
3
(SPL)
Transceiver
12:00
FIL2
METER
Po
USB
CONVENIENT
14.100.00
1
P.AMP
1
F-INP
ENT
HM-151
BW 2.4k SFT
TX
To operate on 1 kHz
higher frequency:
SPLIT LOCK FUNCTION
M-1) while rotating
Accidentally
releasing [F-4 XFC] (M
USB
14.100.00
1
[DIAL] changes the receive frequency. To prevent
e Rotate [DIAL] while pushing and holding [F-4
this, use both the split lock and dial lock functions to
XFC] (M
M-1) to set the transmit frequency to 21.310
change the transmit frequency only. The split lock
MHz.
function cancels the dial lock function while pushing
• [XFC] on the HM-151 can also be used.
M-1) during split frequency
and holding [F-4 XFC] (M
• The transmit frequency can be monitored while pushing
operation.
VFO
USB
FIL2
ATT
OFF
and holding [F-4 XFC].
ANT
1
BW 2.4k SFT
VFO
The dial lock’s effectiveness during split frequency operation can be selected in the miscellaneous (others)
set mode for both receive and transmit frequencies;
or only the receive
frequency. (p. 129)
:
0
USB
14.100.00
1
P.AMP
1
12:00
FIL2
METER
Po
USB
SPLIT
TX
VFO
USB
FIL2
r Now you can receive on 21.290 MHz
ATT and transmit
OFF
14.100.00
1
on 21.310 MHz.
USB
To swap the transmit and receive frequencies, push
M-1) to exchange the VFO A and VFO B.
[F-2 A/B] (M
ANT
1
89
BW 2.4k SFT
VFO
:
0
USB
METER
Po
14.100.00
1
P.AMP
1
SPLIT
TX
VFO
USB
12:00
FIL2
FIL2
USB
6
FUNCTIONS FOR TRANSMIT
■ Quick split function
When you find a DX station, an important consideration is how to set the split frequency.
[AF]
M-1) for 1 sec., split
When you push and hold [F-1 SPL] (M
frequency operation is turned ON, the undisplayed VFO is
automatically changed according to the plus/minus shift frequency programmed in the miscellaneous (others) set
mode (p. 129) or equalized with the displayed VFO when
0.000 MHz (default) is programmed as the split offset frequency.
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
Menu selection (Example: M-1)
This shortens the time needed to start split frequency
operation.
• Push [MENU/GRP] for 1 sec. once or twice to select
the menu group M. Selection from: M, S or G (Graphic)
• Push [MENU/GRP] momentarily one or more times to
select the menu M-1. Selection from: M-1, M-2 or M-3
Quick split operation is turned ON by default but can be
turned OFF in the miscellaneous (others) set mode (p. 129).
q Suppose you are operating at 21.290 MHz (USB)
in VFO A.
M-1), rotate
e While pushing and holding [F-4 XFC] (M
[DIAL] to set the frequency offset between transmit and receive.
• [XFC] on the HM-151 can also be used.
• The transmit frequency can be monitored while pushing
and holding [F-4 XFC].
6
M-1) for 1 sec.
w Push and hold [F-1 SPL] (M
• Split frequency operation is turned ON.
• The VFO A and VFO B are equalized.
ANT
1
BW 2.4k SFT
TX
VFO
:
0
USB
METER
Po
1
PRACTICAL EXAMPLE
P.AMP
1
VFO
14.100.00
USB
12:00
FIL2
USB
PRACTICAL EXAMPLE
FIL2
ANT
ATT
BW 2.4k SFT
When you are searching for DX stations
you
When
you are working a pile-up and you
want
to U S B0
ANT OFFBW and
1
2.4k SFT
0
USB
14.100.00
1
1
FIL2
VFO
USB
FIL2
VFO for
suspect that a DX station may say “up ‘X’ kHz”
start split frequency operation to simplifyMETER
picking out
METER
Po
Po
14.100.00
their receive frequency:
stations:
1
USB
14.100.00
1
P.AMP
SPLIT
P.AMP
1
SPLIT
TX
VFO
1
FIL2
T X VFO USB
M-1) momentarily,ATTand push
OPERATION 1
q Push [F-1 SPL ] (M
M-1)ATT
A
/
B
M-1) for 1 sec. OFF
q Push and hold [F-1 SPL ] (M
for
1
sec.
to
and
hold
[F-2
] (M
1
OFF
USB
14.100.00
1
• The transmit (VFO B) frequency is equalized to the restandby for split operation.
ceive (VFO A) frequency and “
” appears.
w If the DX station’s operator says “up 10 kHz.”
w Rotate [DIAL] to set your receive frequency in the
M-1).
• Push [F-INP/ENT], [1], [0] then [F-1 SPL] (M
• Or, rotate the tuning dial.
VFO A.
e Announce your receive frequency.
OPERATION 2
r After you catch one of the calling stations’ call
If the DX station’s operator says “down 5 kHz” besigns, push and hold the PTT switch to respond.
fore you enter standby for split operation:
• While pushing and holding [F-4 XFC], you can moniM-1).
➥ Push [F-INP/ENT], [•], [5] then [F-1 SPL] (M
tor your transmit frequency.
USB
FIL2
14.100.00
• The split function is turned ON and “5 kHz down” frequency is entered in the sub readout.
90
6
FUNCTIONS FOR TRANSMIT
D Split offset frequency setting
By setting an often-used split frequency offset in advance, you can operate the quick split function to select split operation at the push of one key.
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-4 OTH] to enter the miscellaneous (others) set mode.
SPLIT Off e Push [F-1 ≤] or [F-2 ≥] to select “S
set.”
r Rotate [DIAL] to set the desired split offset.
• The split offset can be selected from –9.999 MHz to
+9.999 MHz.
• Push [F-4 DEF] for 1 sec. to return to default value.
Z(MENU/GRP)] twice to return the normal opt Push [Z
erating mode.
D Quick split setting
q Enter the miscellaneous (others) set mode as
above.
Quick
w Push [F-1 ≤] or [F-2 ≥] to select “Q
SPLIT,” then rotate [DIAL] to select the desired
setting.
• Push [F-4 DEF] for 1 sec. to return to default setting.
Z(MENU/GRP)] twice to return the normal ope Push [Z
erating mode.
91
[AF]
[MENU/GRP] [F-1] [F-2] [F-4]
[DIAL]
FUNCTIONS FOR TRANSMIT
6
■ Measuring SWR
The IC-7000 has a built-in circuit for measuring antenna SWR—no external equipment or special adjustments are necessary.
The IC-7000 can measure SWR in 2 ways—spot measurement and plot measurement.
Menu selection (Example: S-1)
• Push [MENU/GRP] for 1 sec. once or twice to select
the menu group S. Selection from: M, S or G(Graphic)
• Push [MENU/GRP] momentarily one or more times to
select the menu S-1. Selection from: S-1, S-2 or S-3
D Spot measurement
q Select CW or RTTY operation with [MODE].
w Confirm that the output power is over 30 W.
e Select S-1.
r Push [F-3 MET] one or more times to select the
SWR meter.
t Key down or push [PTT] to transmit; then read the
actual SWR from the meter.
➠ ≤ 1.5 well matched antenna
➠ > 1.5 check antenna or cable connection, etc.
SWR
1
1.5
2
-
3
[MENU/GRP]
[F-3]
∞
The best match is in this range.
6
D Plot measurement
Plot measurement allows you to measure the SWR
over an entire band.
q Confirm that the output power is over 30 W.
w Set the center frequency for the SWR to be measured.
e Select G-3 (SWR meter).
r Push and hold [F-4 STEP] for 1 sec. one or more
times to select the desired measuring step from 10,
50, 100 and 500 kHz.
t Push [F-2] or [F-3] one or more times to select the
desired number of measuring steps from 3, 5, 7, 9,
11, and 13 steps.
y Push [F-1] to start the measuring.
u Push and hold [PTT] on the microphone to measure the SWR.
• Frequency marker, “∫,” appears below SWR graph.
• RTTY mode is automatically selected.
i When releasing [PTT], the frequency marker and
frequency indication move to the next frequency to
be measured.
o Repeat steps u and i to measure SWR over the
entire frequency range.
!0 When the measured SWR is less than 1.5:1, the
antenna is well matched with the transceiver in the
measured frequency range.
Push [F-1] to start
mesuring.
Push [F-4] to Select
SWR mesuring steps.
Push [F-2] or [F-3] to select number of
SWR mesuring steps.
• Measuring (after pushing [F1])
Frequency marker appears and moves
after measurement.
4.0 : 1
3.0 : 1
2.0 : 1
1.5 : 1
1.0 : 1
The antenna is well matched in this range
92
7
VOICE RECORDER FUNCTIONS
■ Digital voice recorder
The transceiver has digital voice memories, up to 4
channels for transmit, and up to 99 channels for receive. A maximum message length of 120 sec. can be
recorded into a receive channel (total message length
for all channels of up to 1500 sec.), and a total message length of 90 sec. can be recorded in transmit
channels.
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: S)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Providing a transmission memory is very convenient
for repeated CQ and number transmissions at contest
times, as well as when making consecutive calls in
DX’pedition.
■ Recording a received audio
D Basic recording
q Select the desired frequency and mode.
w Select S-1.
e Push [F-1 VO] to call up the voice recorder menu.
• If the transmit voice memory channels (T1–T4) screen
Z(MENU/GRP)] then push [F-1 RX] to
appears, push [Z
select the receive voice memory channel.
• If the voice root menu appears, push [F-1 RX] to select
the receive voice memory menu. The voice recorder
starting menu can be changed in the miscellaneous
(others) set mode. (p. 134)
r Push and hold [ANF/• REC] for 1 sec. to start
recording while receiving a signal.
• Records audio into the new channel.
•“
” appears and the recording timer counts up.
• The operating frequency, mode and current time are
programmed as the memory names automatically.
t Push and hold [ANF/• REC] for 1 sec. again to
stop recording.
•“
” disappears.
• Recording is automatically terminated after 120 sec. or
when a total of the recorded time becomes 1500 sec.
Z(MENU/GRP)] twice to exit the voice recoder
y Push [Z
mode.
The voice recoder stores the received audio in 15
sec. blocks. Thus the total recording time is reduced by 15 sec. each time recording is stopped.
CONVENIENT
MIC Memo FUNCTION
While recordig received audio, speak into microphone
(without pushing [PTT]) to record your comment, impression or some information with recorded audio.
This function can be activated in the voice set mode.
(p. 99)
93
[MENU/GRP] [F-1] [F-2] [ANF/•REC]
Either
Y or Z
VOICE RECORDER FUNCTIONS
7
D One-touch voice recording
To record the receiving signal contents immediately,
one-touch voice recording is available.
q Push and hold [ANF/• REC] for 1 sec. while receiving a signal to start recording.
•“
” blinks.
• Records audio into the new channel.
w Push and hold [ANF/• REC] for 1 sec. again to
stop recording.
Blinks
[ANF/•REC]
• Recording is automatically terminated after 120 sec. or
when a total of the recorded time becomes 1500 sec.
■ Playing the recorded contents
q Select S-1.
w Push [F-1 VO] to call up the voice recorder menu.
• If the transmit voice memory channels (T1–T4) screen
Z(MENU/GRP)] then push [F-1 RX] to
appears, push [Z
select the receive voice memory channel.
• If the voice root menu appears, push [F-1 RX] to select
the receive voice memory menu. The voice recorder
starting menu can be changed in the miscellaneous
(others) set mode.
7
[MENU/GRP] [F-1] [F-2] [F-3]
e Push [F-1 ≤] or [F-2 ≥] to select the desired
recorded contents, then push [F-3 PLY] to playback.
•“
” appears.
Z(MENU/GRP)]) to
r Push [F-3 PLY] again (or push [Z
stop playback, if desired.
• Playback is terminated automatically when all of the
recorded contents in the channel are played.
Z(MENU/GRP)] twice to exit the voice recoder
t Push [Z
mode.
94
7
VOICE RECORDER FUNCTIONS
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: S)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
■ Erasing the recorded contents
The recorded contents can be erased independently
by channel.
q Select S-1.
w Push [F-1 VO] to call up the voice recorder menu.
• If the transmit voice memory channels (T1–T4) screen
Z(MENU/GRP)] then push [F-1 RX] to
appears, push [Z
select the receive voice memory channel.
• If the voice root menu appears, push [F-1 RX] to select
the receive voice memory menu. The voice recorder
starting menu can be changed in the miscellaneous
(others) set mode. (p. 134)
[MENU/GRP] [F-1] [F-2] [F-4]
e Push [F-1 ≤] or [F-2 ≥] to select the desired
recorded channel to be erased, then push and hold
[F-4 CLR] for 1 sec. to erase the contents.
Z(MENU/GRP)] twice to exit the voice recoder
r Push [Z
mode.
Be careful!—the erased contents CANNOT be recalled.
Erasing a long message takes a little time, and a maximum message length (120 sec./channel) takes over 1
sec.
When resetting the CPU, the transceiver clears all of the voice memory area (1500 sec.), and it takes almost 30
sec. In these cases, you can use the record function, but you cannot playback the recorded contents during the
clearing process unitil it is completed.
95
VOICE RECORDER FUNCTIONS
7
■ Recording a message for transmit
D Recording
To transmit a message using a voice recorder, record
the desired message in advance as described below.
q Select S-1.
Z(MENU/GRP)] to select the
w Push [F-1 VO ] then [Z
voice root menu.
• If the voice root menu appears, skip the pushing
Z(MENU/GRP)]. The voice starting menu can be
[Z
changed in the miscellaneous (others) set mode. (p.
134)
[MENU/GRP] [F-1] [F-3]
e Push [F-3 MIC ] to select the voice memory
recording mode.
Y(MENU/GRP)] then rotate [DIAL] to adjust
r Push [Y
REC LEVEL” inthe mic gain control so that the “R
dicator reads within maximum.
• Speak into the microphone without pushing [PTT].
• Push [F-4 DEF] to select the default mic gain.
Z(MENU/GRP)] to exit the mic gain adjustment
• Push [Z
condition.
t Push [F-1 ≤≥] to select the desired memory channel, then push and hold [F-3 REC ] for 1 sec. to
start recording.
• Speak into the microphone without pushing [PTT].
• Previously recorded contents are cleared.
7
Z(MENU/GRP)]) to
y Push [F-3 REC] again (or push [Z
stop recording.
• Recording is automatically terminated when the total
time of recorded messages, T1–T4, becomes 90 sec.
Z(MENU/GRP)] twice to exit the voice memu Push [Z
ory screen.
D Confirming/Erasing the recorded message
• Playing the recorded contents
• Erasing the recoded contents
q Call up the voice memory recording mode as described in steps q to e as shown above.
w Push [F-1 ≤≥] to select the desired memory channel, then push [F-2 PLY] to start playback.
q Call up the voice memory recording mode as described in steps q to e as shown above.
w Push [F-1 ≤≥] to select the desired memory channel to be erased, push [F-2 PLY] to start playback.
•“
” appears.
e Push [F-2 PLY] again to stop playback, if desired.
Z(MENU/GRP)] twice to exit the voice memr Push [Z
ory mode
•“
” appears.
e Push and hold [F-4 CLR] for 1 sec. to erase the
contents.
Z(MENU/GRP)] twice to exit the voice memr Push [Z
ory mode.
96
7
VOICE RECORDER FUNCTIONS
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: S)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
■ Programming a memory name for transmit
Memory channels can be tagged with alphanumeric
names of up to 5 characters each.
Capital letters, small letters, numerals, some symbols
_
(! # $ % & ¥ ? " ' ` ^ + – ✱ / . , : ; = < > ( ) [ ] { } | _ @)
and space can be used. (See the step t below.)
q Record a message as described on the previous
page.
w Call up the voice memory recording mode as described in steps q to e (see the instructions for
recording at previous page).
e Push [F-1 ≤] or [F-2 ≥] to select the desired voice
memory.
r Push [F-4 NAM] to enter memory name editing.
• A cursor appears and blinks.
• Memory channel names of no-recorded channels
cannnot be selected.
Y(MENU/GRP)] several times to select the det Push [Y
sired character group.
• [ABC], [abc], [123] or [etc] indicates the capital letters,
small letters, numerals or symbols, respectively
y Input the desired character by rotating [DIAL].
• Push [F-1 Å] or [F-2 Ç] for cursor movement.
• Push [F-3 DEL] to delete the selected character.
• Push [F-4 SPC] to input a space.
• Pushing the HM-151’s keypad, [0]–[9], can also enter
numerals.
Z(MENU/GRP)] to input and set the name.
u Push [Z
• The cursor disappears.
i Repeat steps e to y to program another voice
memory’s name, if desired.
Z(MENU/GRP)] twice to exit the voice memo Push [Z
ory screen.
97
[F-1]
[MENU/GRP] [F-2] [F-3] [F-4]
Either
Y or Z
VOICE RECORDER FUNCTIONS
7
■ Sending a recorded message
q Select S-1.
w Push [F-1 VO] to call up the voice recorder menu.
• If the receive voice memory channels screen appears,
Z(MENU/GRP)] then push [F-2 TX] to select the
push [Z
transmit voice memory channel.
• If the voice root menu appears, push [F-2 TX] to select
the transmit voice memory menu. The voice recorder
starting menu can be changed in the miscellaneous
(others) set mode.
[F-1]
[MENU/GRP] [F-2] [F-3] [F-4]
e Push [F-1 T1 ] — [F-4 T4 ] to transmit the contents.
T1”– “T
T4” are highlighted while transmitting.
• “T
r Push the selected memory channel key, [F-1 T1]
— [F-4 T4], again to stop, if desired.
Z(MENU/GRP)] twice to exit the voice memt Push [Z
ory screen.
For your information
When an external keypad is connected to the pin 2
and pin 7 of the [MIC] connecter, the recorded
message, T1–T4, can be transmitted without opening the voice recorder set screen.
See page 135 for details.
7
D Transmit level setting
q Call up the voice memory recording mode as described in steps q to w as above.
Y(MENU/GRP)] to select the voice memory
w Push [Y
transmit level set mode.
e Push the desired memory channel key, [F-1 T1] –
[F-3 T3], momentarily to transmit the contents.
r Rotate [DIAL] to adjust the transmit voice level.
• Push [F-4 DEF] to select the default condition.
Z(MENU/GRP)] to return to the voice recorder
t Push [Z
screen.
98
7
VOICE RECORDER FUNCTIONS
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: S)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
■ Voice set mode
[MENU/GRP] [F-1] [F-2] [F-4]
q Select S-1.
Z(MENU/GRP)] to select the
w Push [F-1 VO ] then [Z
voice root menu.
• If the voice root menu appears, skip the pushing
Z(MENU/GRP)]. The voice starting menu can be
[Z
changed in the miscellaneous (others) set mode. (p.
134)
e Push [F-4 SET ] to enter the voice recorder set
mode.
r Push [F-1 ≤] or [F-2 ≥] to select the desired item,
then rotate [DIAL] to set the selected function ON
and OFF.
• Push [F-4 DEF] for 1 sec. to select the default condition.
Z(MENU/GRP)] to return to the voice root
t Push [Z
menu.
D Voice set mode
1. Auto Monitor
This item turns the auto monitor function ON and OFF.
When this function is ON, the monitor function is automatically turned ON while transmitting a voice memory message.
ON
OFF
Automatic monitor function Automatic monitor function
is ON. (default)
is OFF.
• Push [F-4 DEF] for 1 sec. to return to default setting.
2. MIC Memo
This item selects the mic memo function ON and OFF.
When this function is ON, and you speak into the microphone (without pushing [PTT]), your voice is
mixed with the received audio and recorded.
This function is convienient when you want to record
some information or comment while recording the received audio.
• Push [F-4 DEF] for 1 sec. to return to default setting.
99
ON
OFF
MIC memo function is ON.
MIC memo function is OFF.
(default)
8
MEMORY OPERATION
■ Memory channels
The transceiver has 501 memory channels including 6
scan edge channels (3 pairs), and 2 call channels. In
addition, a total of 5 memory banks (99 memory channel each), A to E, are available for usage by group, etc.
All 503 memory/call channels are tuneable which
means the programmed frequency can be tuned temporarily with [DIAL], etc., in memory mode.
Memory mode is very useful for quickly changing to
often-used frequencies.
MEMORY
CHANNEL
NUMBER
CAPABILITY
TRANSFER
TO VFO
OVERWRITING
CLEAR
Regular
(split memory)
1–99
(in each
banks)
Independent transmit and receive
frequencies and one mode in each
memory channel.
In addition, tone frequencies can
also be stored for repeater use.
Yes
Yes
Yes
Scan edges
1A–3B
(common)
One frequency and one mode in
each memory channel as scan
edges for programmed scan.
Yes
Yes
No
Call channels
(split memory)
C1, C2
(common)
Same as regular channels, but only
frequencies in 144 MHz (C1), 430
MHz (C2) band can be programmed.
Yes
Yes
No
MEMORY
CHANNEL
7
8
■ Memory channel selection
q Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
w Select M-2.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times to
select the menu M-2.
e Push [F-4 V/M] to select memory mode.
r Rotate [M-ch] (inner) control to select the desired
memory channel.
• All memory channels including blank channels can be
selected.
• Rotating [RIT] (outer) control changes the bank.
Y]/[Z
Z] on the microphone also change the channels.
• [Y
[MENU/GRP]
[RIT] (outer) control [F-4]
[EXAMPLE]: Selecting memory channel 17.
t To return to VFO mode, push [F-4 V/M] again.
V/M
100
8
MEMORY OPERATION
■ Memory programming
Memory channel programming can be performed either in VFO mode or in memory mode.
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: M-1, M-2 or M-3
Either
Y or Z
D Programming in VFO mode
q Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
w Set the desired frequency and operating mode in
VFO mode.
• If you want to program the split frequency function, program both receive and transmit frequencies into VFO
A and B, then turn ON the split function. (p. 89)
• If you want to program a repeater function, set a tone
frequency (p. 60) in addition to the receive/transmit frequencies.
e Select M-2.
r Push [F-1 MEM ] to display the memory channel
contents.
[MENU/GRP]
[RIT] (outer) control
[F-2]
[EXAMPLE]: Programming 7.088 MHz/LSB into ch 12.
• Memory channel contents appear above the multi-function key indicator.
• Push [F-1 LST ] to display the memory channel list.
This is convenient for selecting the desired channel.
Z(MENU/GRP)] to exit the memory channel list.
Push [Z
t Rotate [M-ch] to select the desired memory channel.
•“
” and “---,---,--” appear if the selected memory
channel is a blank channel (and does not have contents).
• Rotating [RIT] (outer) control changes the bank.
y Push and hold [F-2 MW] for 1 sec. to program the
displayed frequency and operating mode into the
selected memory channel.
To check the programmed contents, push [F-4 V/M]
to select memory mode.
MW
Push for
1 sec.
101
MEMORY OPERATION
8
D Programming in memory mode
[EXAMPLE]: Programming 21.280 MHz/USB into
ch 18.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
[Y]
[Z]
[MENU/GRP]
[F-2]
[F-4]
q Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
w Select M-2.
e Push [F-4 V/M] to select memory mode, then select the desired memory channel with [M-ch].
• Memory channel contents appear instead of the VFO’s
frequency readout.
r Set the desired frequency and operating mode.
Y(BAND)] or
• To program a blank channel, push [Y
Z(BAND)] to select the desired band or use direct fre[Z
quency entry with the keypad (HM-151).
t Push and hold [F-2 MW] for 1 sec. to program the
displayed frequency and operating mode into the
memory channel.
MW
Push for
1 sec.
8
102
8
MEMORY OPERATION
■ Memory channel list
The memory channel list simultaneously shows 7
memory channels and their programmed contents.
You can select a desired memory channel from the
memory channel list.
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: M-1, M-2 or M-3
Either
Y or Z
D Selecting a memory channel using the memory channel list
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
MEM
Push
[MENU/GRP] [F-1] [F-4]
q Select M-2.
w Push [F-4 V/M] to select memory mode.
MEM, LST) twice to enter the memory
e Push [F-1] (M
channel list.
r Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
LST
Push
• [PBT/M-ch/RIT] indicator (Green) goes out.
t Rotate [M-ch] (inner) control to select the desired
memory channel.
• All memory channels including blank channels can be
selected.
Y]/[Z
Z] on the microphone also changes the channels.
• [Y
y To exit the memory
Z(MENU/GRP)] twice.
[Z
103
channel
list,
push
Rotate
MEMORY OPERATION
8
D Setting a memory channel as a select memory
Select memory channels are used for select memory
scan. Select memory scan repeatedly scans the select memory channels only. This is useful to speed up
the memory scan interval. Of course, select memory
channels are also scanned during normal memory
scan.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
q Select the memory channel list as described at left.
w Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
e Rotate [M-ch] (inner) control to select the desired
memory channel.
[MENU/GRP]
[F-1]
“ß” appears for select memory channel.
• All memory channels including blank channels can be
selected.
Y]/[Z
Z] on the microphone also changes the channels.
• [Y
r Push [F-1 SEL] to set the memory channel as a
select memory or not.
t Repeat steps e to r to program another memory
channel as a select memory channel, if desired.
Z(MENU/GRP)] twice to exit the memory
y Push [Z
channel list.
Setting select memory channels is also possible in
the memory scan indication. (p. 113)
Push [F-1 SEL]
8
D Selecting a memory bank
The IC-7000 has a total of 5 memory banks (99 memory channel each), A to E, available for usage by
group, etc.
• Memory channel list indication
q Select the memory channel list as described at left.
w Push [F-4 BNK] several times to select the desired
memory bank.
• Rotating [RIT] (outer) control also changes the bank.
Z(MENU/GRP)] twice to exit the memory
e Push [Z
channel list.
Bank indication
Bank indication
q Select the memory channel as described at p. 100.
w Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
BNK
• [PBT/M-ch/RIT] indicator (Green) goes out.
e Rotate [RIT] (outer) control to select the desired
memory bank.
Push
[MENU/GRP]
[RIT] (outer) control
[F-4]
104
8
MEMORY OPERATION
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: M-1, M-2 or M-3
Either
Y or Z
D Memory names
All memory channels (including scan edges) can be
tagged with alphanumeric names of up to 9 characters each.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
Capital letters, small letters, numerals, some symbols
_
(! # $ % & ¥ ? " ’ ` ^ + – ✱ / . , : ; = < > ( ) [ ] { } | _ @)
and spaces can be used.
• Editing (programming) memory names
q Select M-2.
w Push [F-4 V/M] to select memory mode.
MEM, LST) twice to enter the memory
e Push [F-1] (M
channel list.
r Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
[DIAL]
• [PBT/M-ch/RIT] indicator (Green) goes out.
t Rotate [M-ch] (inner) control to select the desired
memory channel.
• All memory channels including blank channels can be
selected.
Y]/[Z
Z] on the microphone also changes the channels.
• [Y
NAM
Selected character
Push
y Push [F-2 NAM] to edit memory channel name.
• A cursor appears and blinks.
• Memory channel names of blank channels cannot be
edited.
Y(MENU/GRP)] several times to select the deu Push [Y
sired character group.
• [ABC], [abc], [123] or [etc] indicates the capital letters,
small letters, numerals or symbols, respectively
Rotate
i Input the desired character by rotating [DIAL].
• Push [F-1 Å] or [F-2 Ç] for cursor movement.
• Push [F-3 DEL] to delete the selected character.
• Push [F-4 SPC] to input a space.
• Pushing the HM-151’s keypad, [0]–[9], can also enter
numerals.
Z(MENU/GRP)] to input and set the name.
o Push [Z
• The cursor disappears.
!0 Repeat steps t to o to program another memory
channel’s name, if desired.
Z(MENU/GRP)] twice to exit the memory
!1 Push [Z
channel list.
105
Ç
Push
MEMORY OPERATION
8
■ Memory clearing
Any unnecessary memory channels can be cleared.
The cleared memory channels become blank channels.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
q Select M-2.
w Push [F-4 V/M] momentarily to select the memory
mode.
e Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
• [PBT/M-ch/RIT] indicator (Green) goes out.
r Rotate [M-ch] to select the memory channel to be
cleared.
t Push and hold [F-3 MCL ] for 1 sec. to clear the
contents.
[MENU/GRP]
[F-3]
[F-4]
• The programmed frequency and operating mode disappear and “
” appears.
y To return to VFO mode, push [F-4 V/M] again.
MCL Push for
1 sec.
8
D Memory clearing using the memory channel list
q Select M-2.
w Push [F-4 V/M] to select memory mode.
MEM, LST) twice to enter the memory
e Push [F-1] (M
channel list.
r Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
• [PBT/M-ch/RIT] indicator (Green) goes out.
t Rotate [M-ch] to select the memory channel to be
cleared (blanked).
y Push and hold [F-3 MCL ] for 1 sec. to clear the
contents.
Z(MENU/GRP)] twice to exit the memory
u Push [Z
channel list.
[MENU/GRP] [F-1] [F-3] [F-4]
MCL
Push for
1 sec.
Programmed frequency
and operating mode
disappear.
106
8
MEMORY OPERATION
■ Frequency transferring
The frequency and operating mode in a memory channel can be transferred to the VFO.
Frequency transferring can be performed in either VFO
mode or memory mode.
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: M-1, M-2 or M-3
Either
Y or Z
D Transferring in VFO mode
This is useful for transferring programmed contents to
VFO.
q Select M-2.
w Push [F-4 V/M ] momentarily to select the VFO
mode.
e Push [F-1 MEM ] to display the memory channel
contents.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
• Memory channel contents appear above the multi-function key indicator.
r Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
[MENU/GRP] [F-1] [F-4]
• [PBT/M-ch/RIT] indicator (Green) goes out.
t Select a memory channel with [M-ch].
•“
” appears if the selected memory channel is a
blank channel (and does not have contents). In this
case transferring is not possible.
[EXAMPLE]: Transferring contents of memory 16.
Operating frequency
: 21.320 MHz/USB (VFO)
Contents of memory 16 : 14.020 MHz/CW
y Push and hold [F-4 V/M] for 1 sec. to transfer the
frequency and operating mode.
• Transferred frequency and operating mode appear in
the display.
V/M
Push for
1 sec.
107
MEMORY OPERATION
8
D Transferring in memory mode
This is useful for transferring frequency and operating mode while operating in memory mode.
[PBT/M-ch/RIT] switch/[M-ch] (inner) control
[PBT/M-ch/RIT] indicator
When you have changed the frequency or operating mode in the selected memory channel.
• Displayed frequency and mode are transferred.
• Programmed frequency and mode in the memory
channel are not transferred, and they remain in
the memory channel.
q Push [PBT/M-ch/RIT] momentarily to select the Mch/RIT function, if the twin PBT is selected.
[MENU/GRP]
[F-4]
• [PBT/M-ch/RIT] indicator (Green) goes out.
w Select M-2.
e Push [F-4 V/M] momentarily to select the memory
mode.
r Rotate [M-ch] to select the memory channel to be
transferred.
•“
” appears if the selected memory channel is a
blank channel (and does not have contents). In this
case transferring is not possible.
t Push and hold [F-4 V/M] for 1 sec. to transfer the
frequency and operating mode.
• Displayed frequency and operating mode are transferred to the VFO.
y Push [F-4 V/M ] momentarily to select the VFO
mode.
8
108
8
MEMORY OPERATION
■ Memo pads
The transceiver has a memo pad function to store frequency and operating mode for easy write and recall.
The memo pads are separate from memory channels.
The default number of memo pads is 5, however, this
can be increased to 10 in the miscellaneous (others)
set mode if desired (p. 132).
Memo pads are convenient when you want to memorize a frequency and operating mode temporarily, such
as when you find a DX station in a pile-up or when a
station is busy for a long time and you want to temporarily search for other stations.
Use the transceiver’s memo pads instead of relying on
hastily scribbled notes that are easily misplaced.
[MENU/GRP] [F-2] [F-3]
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: S)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
D Writing frequencies and operating modes into memo pads
q Select S-3.
w Push [F-2 MPW] to program the frequency into a
memo pad.
Displayed frequency and mode
When you write a 6th frequency and operating mode,
the oldest written frequency and operating mode are
automatically erased to make room for the new settings.
MPW
Push
NOTE: Each memo pad must have its own unique
combination of frequency and operating mode;
memo pads having identical settings cannot be
written.
MP5
Newest
MP4
MP3
MP2
MP1
Oldest
The oldest written frequency
and mode are erased.
109
MEMORY OPERATION
8
D Calling up a frequency from a memo pad
You can call up the desired frequency and operating
mode of a memo pad by pushing [F-3 MPR] in the S3 menu.
VFO or memory mode
• Make sure S-3 is selected in advance.
• Both VFO and memory modes can be used.
• The frequency and operating mode are called up, starting
from the most recently written.
MPR
Push
When you call up a frequency and an operating mode
from memo pads with [F-3 MPR], the previously displayed frequency and operating mode are automatically stored in a temporary pad. The frequency and
operating mode in the temporary pad can be recalled
by pushing [F-3 MPR] one or more times.
MEMO PADS
MP5
MP4
NOTE: If you change the frequency or operating
mode called up from a memo pad, the frequency
and operating mode in the temporary pad are
erased.
MP3
MP2
MP1
MPR
Push
8
110
9
SCAN OPERATION
■ Scan types
PROGRAMMED SCAN
PRIORITY WATCH
Repeatedly scans between two scan edge frequencies
(scan edge memory channels 1A and 1B).
Checks for signals on a memory while operating on a
VFO frequency.
Scan
Scan edge 1A or 1B
Scan edge 1B or 1A
VFO
frequency
Memory
channel
Jump
This scan operates in VFO mode.
This scan operates in VFO mode.
MEMORY SCAN
SELECTED MEMORY SCAN
Repeatedly scans all programmed memory channels.
Repeatedly scans all selected memory channels.
ß (select)
Mch 2
Mch 3
Mch 1 ß (select)
BLANK
Mch 4
ß (select)
Mch 99
Mch 7
ß (select)
ß (select)
BLANK
ß (select)
Mch 2
Mch 5
Mch 4
Mch 1 ß (select)
Mch 6
This scan operates in memory mode.
Mch 3
ß (select)
Mch 99
Mch 7
ß (select)
ß (select)
Mch 5
Mch 6
This scan operates in memory mode.
■ Preparation
• Channels
For programmed scan: Program scan edge frequencies into scan edge memory channels 1A and 1B.
(p. 101)
For memory scan: Program two or more memory
channels except scan edge memory channels.
For memory select scan: Designate two or more memory channels as select memory channels—select a
memory channel, then push [F-2 SEL ] in the S-2
menu (memory mode) to designate the channel as a
select memory channel.
For priority watch: Program one memory channel to be
watched.
• Scan resume ON/OFF
You can select the scan to resume or cancel when detecting a signal, in the miscellaneous (others) set
SCAN Resume.” Scan resume ON/OFF
mode, item “S
must be set before operating a scan. See p. 132 for
ON/OFF setting and scan resume condition details.
• Scan speed
Scan speed can be selected from 2 levels, high or low,
in the miscellaneous (others) set mode. See p. 132 for
details.
111
• Squelch condition
SCAN
STARTS
WITH
PROGRAMMED
SCAN
MEMORY SCANS
PRIORITY WATCH
The scan continues
until it is stopped manually, and does not
pause even if it detects signals.
Scan pauses on each
channel when the
scan resume is ON;
not applicable when
OFF.
SQUELCH
OPEN This is not applicable
when the scan resume is OFF and a
programmable step
(more than 1 kHz) is
selected.
Scan stops when detecting a signal.
If you set scan resume ON in the miscella-
SQUELCH neous (others)l set mode, the scan pauses for
CLOSED 10 sec. when detecting a signal, then resumes. When a signal disappears while scan
is paused, scan resumes 2 sec. later.
SCAN OPERATION
9
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
■ Programmed scan operation
q Select S-2.
w Push [F-3 V/M] to select VFO mode.
e Select the desired operating mode.
• The operating mode can also be changed while scanning.
r Set [RF/SQL] open or closed.
• See page at left for squelch condition.
• If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 1, 35, 129 for details.
[RF/SQL]
[MENU/GRP] [F-1]
[F-3]
t Push [F-1 SCN] to start the scan.
• Decimal point blinks while scanning.
y When the scan detects a signal, the scan turns
OFF, pauses or ignores it depending on the resume setting and the squelch condition.
u To cancel the scan push [F-1 SCN].
Select
VFO mode
NOTE: If the same frequencies are programmed
into both scan edge memory channels 1A and 1B,
programmed scan does not start.
then push [F-1 SCN]
9
■ Memory scan operation
q Select the desired memory bank, if necessary.
● Push [PBT/M-ch/RIT] momentarily to select the
M-ch/RIT function, if the twin PBT is selected.
[RF/SQL]
• [PBT/M-ch/RIT] indicator (Green) goes out.
● Rotate [RIT] (outer) control to select the desired
memory bank.
w Select S-2.
e Push [F-3 V/M] to select memory mode.
r Close the squelch with [RF/SQL].
t Push [F-1 SCN] to start the scan.
[MENU/GRP] [F-1]
[RIT] (outer) control
[F-3]
• Decimal point blinks while scanning.
y When the scan detects a signal, the scan stops or
pauses depending on the resume setting.
u To cancel the scan push [F-1 SCN].
Select
memory mode
NOTE: Two or more memory channels must be
programmed for memory scan to start.
then push [F-1 SCN]
112
9
SCAN OPERATION
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
■ Select memory scan operation
q Select S-2.
w Push [F-3 V/M] to select memory mode.
e Close the squelch with [RF/SQL].
r Push [F-1 SCN] to start the memory scan.
• Decimal point blinks while scanning.
t Push [F-2 SEL] to change the memory scan to select memory scan.
y When the scan detects a signal, the scan stops or
pauses depending on the resume setting.
u To cancel the scan push [F-1 SCN].
[RF/SQL]
[MENU/GRP] [F-1] [F-2] [F-3]
NOTE: Two or more memory channels must be
designated as select memory channels for select
memory scan to start (see p. 104).
Select
memory mode.
While scan function is not active, pushing [F-2
SEL] sets the select memory channels ON or OFF.
And pushing and holding [F-2 SEL ] for 2 sec.
clears the all select memory channels.
Designate
“★.”
Push [F-1 SCN],
then push [F-2 SEL].
■ Priority watch
q Select VFO mode, then set a frequency.
w Close the squelch with [RF/SQL].
e Set the desired memory channel as the channel to
be watched.
r Select S-2.
t Push [F-2 PRI] to start the priority watch.
• “ ” appears and decimal points blink while watching
VFO, and then “ ” and decimal points blink while
watching a memory channel.
[RF/SQL]
[MENU/GRP] [F-2]
Appears while scanning
y When the scan detects a signal, the scan pauses
for 10 sec. or until the signal disappears, depending on the resume setting.
u To cancel the scan push [F-2 PRI].
Select
VFO mode.
NOTE: The paused condition when detecting a signal differs depending on the scan resume condition. (p. 132)
resume on: pauses for 10 sec.
resume off: pauses until the signal disappears.
Select watching
channel.
Push [F-2 PRI].
113
ANTENNA TUNER OPERATION
10
■ Optional AT-180 AUTOMATIC ANTENNA TUNER operation
The AT-180 automatic antenna tuner matches the IC7000 to the connected antenna automatically. Once the
tuner matches an antenna, the variable capacitor setting
are memorized as a preset point for each frequency
range (100 kHz steps). Therefore, when you change the
frequency range, the variable capacitors are automatically preset to the memorized point.
NOTE:
• The AT-180 can match both HF and 50 MHz
bands. However, operation is different for the HF
and 50 MHz bands.
• When connecting the AT-180, the IC-7000’s output
power must be set over the 10 W. Otherwise, the
AT-180 may not be tuned correctly. (AT-180’s minimum operating input power is 8 W.)
CAUTION: NEVER transmit with the tuner ON
when no antenna is connected. This will damage
both the transceiver and antenna tuner.
The AT-180 cannot be used for the 144/430 MHz
bands. When operating on the 144/430 MHz band,
pushing [TUNER/CALL] selects the call channel
(p. 100).
[TUNER/CALL]
D Tuner operation
• For the HF band:
Push [TUNER/CALL] to turn the tuner ON. The antenna is tuned automatically during transmission
when the antenna SWR is higher than 1.5:1.
• When the tuner is ON, “
” indication appears.
• For the 50 MHz band:
Push and hold [TUNER/CALL] for 1 sec. to tune the
antenna. If “
” indicator blinks slowly while transmitting, push and hold [TUNER/CALL] for 1 sec.
again to re-tune the antenna.
9
D Manual tuning
During SSB operation on HF bands at low voice levels, the AT-180 may not be tuned correctly. In such
cases, manual tuning is helpful.
Push [TUNER/CALL] for 2 sec. to start manual tuning.
• CW mode is selected, a side tone is emitted, and “
indicator blinks; then, the previous mode is selected.
”
If the tuner cannot reduce the SWR to less than 1.5:1
after 20 sec. of tuning, “
” indicator disappears.
In this case, check the following:
• the antenna connection and feedline
• the antenna SWR (p. 36; meter function)
Through inhibit (HF bands only)
The AT-180 has a through inhibit condition. When selecting this condition, the tuner can be used at poor
SWR’s. In this case, automatic tuning in the HF bands
activates only when exceeding SWR 3:1. Therefore,
manual tuning is necessary each time you change the
frequency. Although termed “through inhibit,” the tuner
will be set to the “through” configuration if the SWR is
higher than 3:1 after tuning.
10
CONVENIENT
• Tuner sensitive condition (HF bands only)
If you require critical tuning at any time during transmission, select the tuner sensitive condition. See
p. 131 for selection.
• Automatic tuner start (HF bands only)
If you want to turn OFF the tuner under conditions of
VSWR 1.5:1 or less, use “automatic tuner on” and
turn the tuner OFF. See p. 130 for turning the function
ON and OFF.
114
10
ANTENNA TUNER OPERATION
Menu group selection
Push [MENU/GRP] for 1 sec.
Selection from: M, S or G(Graphic)
Menu selection (Example: M)
Push [MENU/GRP] momentarily.
Selection from: S-1, S-2 or S-3
Either
Y or Z
■ Optional AH-4 AUTOMATIC ANTENNA TUNER operation
The AH-4 matches the IC-7000 to a long wire antenna
more than 7 m/23 ft long (3.5 MHz and above).
• See p. 20 for connection.
• See the AH-4 instruction manual for AH-4 installation and
antenna connection details.
RDANGER!: HIGH VOLTAGE!
NEVER touch the antenna element while tuning or
transmitting.
NEVER operate the AH-4 without an antenna wire.
The tuner and transceiver will be damaged.
AH-4 setting example:
For mobile operation
Optional AH-2b
antenna element
NEVER operate the AH-4 when it is ungrounded.
Transmitting before tuning may damage the transceiver. Note that the AH-4 cannot tune when using a
1⁄2 λ long wire or on a multiple of that frequency.
For outdoor operation
Long wire
[TUNER/CALL]
D AH-4 operation
Tuning is required for each frequency. Be sure to retune the antenna before transmitting when you
change the frequency—even slightly.
q Set the desired frequency in an HF band.
• The AH-4 will not operate on frequencies outside of
ham bands.
w Push and hold [TUNER/CALL] for 1 sec.
•“
” indicator and “CW” appears while tuning.
e“
” indicator stays ON when tuning is complete.
• When the connected wire cannot be tuned, “
” indicator blinks, and the AH-4 is bypassed and the antenna wire is connected to the antenna connector on
the transceiver directly.
r To bypass the AH-4 manually, push [TUNER/
CALL].
115
CONVENIENT
• PTT tune function
The AH-4 is always tuned when the PTT is pushed
after the frequency is changed (more than 1%). This
function removes the “push and hold [TUNER/CALL]”
operation and activates first transmission on the new
frequency. This function is turned ON in the miscellaneous (others) set mode (p. 131).
PACKET OPERATION
11
■ Packet operation
D Data socket
q
PIN #/NAME
q DATA IN
w GND
w
r
e
t
e PTTP
y
r DATA OUT
t AF OUT
Rear panel view
y SQL
DESCRIPTION
Communication data input.
Ground for DATA IN, DATA OUT and AF OUT.
Transmits when grounded.
When grounded, microphone input (pin 6) of [MIC]
connector will be disconnected.
Outputs 9600 bps receive data.
Outputs 1200 bps receive data.
Squelch output.
Goes to ground when squelch opens.
D Adjusting the data speed
q Select M-3.
w Push [F-4 9600] to select the 9600 baud mode
ON and OFF.
•“
” appears when the 9600 baud mode is activated.
[MENU/GRP]
[F-4]
10
D Adjusting the transmit signal output from the TNC
When setting data transmission speed to 9600 baud
bps, the data signal coming from the TNC is applied
exclusively to the internal limiter circuitry to automatically maintain bandwidth.
NEVER apply data levels from the TNC of over 0.6
Vp-p, otherwise the transceiver will not be able to
maintain the band width and may possibly interfere
with other stations.
NOTE: Read the instructions supplied with your
TNC carefully before attempting packet operation
with the IC-7000.
11
1. When using a level meter or oscilloscope, adjust
the TX audio level (DATA IN level) from the TNC as
follows.
0.4 Vp-p (0.2 Vrms): recommended level
0.2–0.5 Vp-p (0.1–0.25 Vrms): acceptable level
2. When not using a measuring device.
q Connect the IC-7000 to a TNC.
w Enter a test mode (“CAL”, etc.) on the TNC, then
transmit some test data.
e When the transceiver fails to transmit test data or
transmits sporadically ([TX] indicator doesn’t light
red or blinks):
- Decrease the TNC output level until [TX] indicator lights red continuously.
When transmission is not successful even though
[TX] indicator lights red continuously:
- Increase the TNC output level.
116
12
CLOCK AND TIMERS
■ Time set mode
This transceiver has a built-in 24-hour clock with
power-off timer function. The clock indication is always
displayed except after pushing [F-INP/ENT] (HM-151).
• Set mode operation
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-3 TIME] to enter the time set mode.
e Push [F-1 ≤] or [F-2 ≥] to select the desired item.
r Rotate [DIAL] to set or select the desired value or
condition.
• Push [F-4 DEF] for 1 sec. to select a default value or
condition.
[AF]
Z(MENU/GRP)] twice to exit the set mode.
t Push [Z
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
[DIAL]
1 Year
2005
This item sets the current year.
Rotate [DIAL], then push [F-3 SET] to set the year.
2 Date
3-15(Tue)
This item sets the current date.
Rotate [DIAL], then push [F-3 SET] to set the date.
3 Time (Now)
This item sets the current time for the built-in 24-hour
clock.
15:00
Rotate [DIAL], then push [F-3 SET] to set the time.
4 CLOCK2 Function
This item turns the second clock indication ON and
OFF instead of 1st clock.
The clock 2 is convenient to indicate the UTC and
other country’s local time, etc.
• Push [F-4 DEF] for 1 sec. to set the default value.
ON
OFF
The clock 2 is displayed in- The clock 2 does not disstead of the 1st clock indica- play. (default)
tion.
5 CLOCK2 Offset
This item sets the desired off-set time period for the
clock 2 indication within –24:00 to +24:00 in 5 min.
steps.
• Push [F-4 DEF] for 1 sec. to set the default value.
± 0:00
+ 9:00
(default)
Rotate [DIAL] to set the
time.
6 Auto Power OFF
This item sets the power-off period for automatic shutdown after the power-on timer has turned power ON.
117
60min
Push [F-3 SET] to enter the time.
CLOCK AND TIMERS
12
D Setting the current year
q Entering time set mode, push [F-1 ≤] to select
Year” item.
“Y
w Set the current year using [DIAL].
Push [SET]” blinks.
• “P
e Push [F-3 SET] to enter the set year.
Z(MENU/GRP)] to cancel the setting.
• Push [Z
Z(MENU/GRP)] twice to exit time set mode.
r Push [Z
D Setting the current date
q Entering time set mode, push [F-1 ≤] or [F-2 ≥] to
Date” item.
select “D
w Rotate [DIAL] to set the current date.
Push [SET]” blinks.
• “P
e Push [F-3 SET] to enter the set date.
Z(MENU/GRP)] to cancel the setting.
• Push [Z
Z(MENU/GRP)] twice to exit time set mode.
r Push [Z
D Setting the current time
q Entering time set mode, push [F-1 ≤] or [F-2 ≥] to
Time (Now)” item.
select “T
w Rotate [DIAL] to set the current time.
Push [SET]” blinks.
• “P
12
e Push [F-3 SET] to enter the set time.
Z(MENU/GRP)] to cancel the setting.
• Push [Z
Z(MENU/GRP)] twice to exit time set mode.
r Push [Z
118
12
CLOCK AND TIMERS
D Clock2 function activity
q Entering time set mode, push [F-1 ≤] or [F-2 ≥] to
CLOCK2 Function” item.
select “C
w Select the CLOCK2 function activity using [DIAL].
Z(MENU/GRP)] twice to exit time set mode.
e Push [Z
D Clock2 offset setting
q Entering time set mode, push [F-1 ≤] or [F-2 ≥] to
CLOCK2 Offset” item.
select “C
w Rotate [DIAL] to set the offset time within –24:00
to +24:00 in 5 min. steps.
Z(MENU/GRP)] twice to exit time set mode.
e Push [Z
D Auto power OFF activity
The transceiver can be set to automatically turn OFF
after a specified period is with beep when no operation is performed. The power-off period can be set to
30–120 min. in 30 min. steps.
q Entering time set mode, push [F-2 ≥] to select
Auto Power OFF” item.
“A
w Set the desired power-off time using [DIAL].
Push [SET]” blinks.
• “P
e Push [F-3 SET] to enter the set time.
Z(MENU/GRP)] to cancel the setting.
• Push [Z
Z(MENU/GRP)] twice to exit timer set mode.
r Push [Z
119
SET MODE
13
■ Set mode description
Set mode is used for programming infrequently
changed values or conditions of functions. This transceiver has a quick set mode, display set mode, timer
set mode and miscellaneous (others) set mode.
• Set mode operation
q Push [AF(SET)] momentarily to enter the set mode
menu.
w Push [F-1 QS ], [F-2 DISP ], [F-3 TIME ] or [F-4
OTH] to enter the desired set mode.
e Push [F-1 ≤] or [F-2 ≥] to select the desired item.
r Set the desired condition using [DIAL].
• Push [F-4 DEF] for 1 sec. to select a default condition
or value.
[AF]
Z(MENU/GRP)] twice to exit the set mode.
t Push [Z
[MENU/GRP]
[F-1]
[F-2] [F-3] [F-4]
[DIAL]
• Start up screen
• Display set mode (p. 124)
Push
[AF]
momentarily
• Set mode menu
• Time set mode (p. 117)
12
13
• Quick set mode (p. 121)
• Miscellaneous (others) set mode (p. 128)
120
13
SET MODE
■ Quick set mode
Mode
Set mode item
Default setting
1
2
3
4
5
6
7
8
RF Power
MIC Gain
SSB TBW (WIDE) L
SSB TBW (WIDE) H
SSB TBW (MID) L
SSB TBW (MID) H
SSB TBW (NAR) L
SSB TBW (NAR) H
100%
50%
100 [Hz]
2900 [Hz]
300 [Hz]
2700 [Hz]
500 [Hz]
2500 [Hz]
CW
1
2
3
4
5
RF Power
Key Speed
CW Pitch
Side Tone Level
Side Tone Level Limit
100%
20WPM
600 [Hz]
50%
ON
RTTY
1
2
3
4
5
RF Power
Twin Peak Filter
RTTY Mark Frequency
RTTY Shift Width
RTTY Keying Polarity
100%
OFF
2125 [Hz]
170 [Hz]
Normal
AM
FM/WFM
1
2
RF Power
MIC Gain
100%
50%
SSB
RF Power (all modes)
This item adjusts the RF output power. The RF output power can be adjusted from 0 to 100% in 1 %
steps.
100%
100% (default)
MIC Gain (SSB/AM/FM modes)
This item adjusts microphone gain from 0 to 100% in
1% steps.
50%
50% (default)
SSB TBW (WIDE) L (SSB mode)
These items set the transmission passband width for
the wide setting by selecting the lower and higher frequencies.
Lower freq. : 100 (default), 200, 300 and 500 Hz
121
100
100 Hz (default)
SET MODE
13
■ Quick set mode (continued)
SSB TBW (WIDE) H (SSB mode)
These items set the transmission passband width for
the wide setting by selecting the lower and higher frequencies.
Higher freq.: 2500, 2700, 2800 and 2900 Hz (default)
2900
2900 Hz (default)
SSB TBW (MID) L (SSB mode)
These items set the transmission passband width for
the middle setting by selecting the lower and higher
frequencies.
Lower freq. : 100, 200, 300 (default) and 500 Hz
300
300 Hz (default)
SSB TBW (MID) H (SSB mode)
These items set the transmission passband width for
the middle setting by selecting the lower and higher
frequencies.
Higher freq.: 2500, 2700 (default) 2800 and 2900 Hz
2700
2700 Hz (default)
SSB TBW (NAR) L (SSB mode)
These items set the transmission passband width for
the narrow setting by selecting the lower and higher
frequencies.
Lower freq. : 100, 200, 300 and 500 Hz (default)
500
500 Hz (default)
SSB TBW (NAR) H (SSB mode)
These items set the transmission passband width for
the narrow setting by selecting the lower and higher
frequencies.
Lower freq. : 2500 (default), 2700, 2800 and 2900 Hz
2500
2500 Hz (default)
13
Key Speed (CW mode)
This item adjusts the CW key speed. The key speed
can be selected from 6 to 60 wpm.
20WPM
20 WPM (default)
CW Pitch (CW mode)
This item adjusts the CW receive pitch. The pitch can
be selected from 300 to 900 Hz in 5 Hz steps.
600
600 Hz (default)
122
13
SET MODE
■ Quick set mode (continued)
Side Tone Level (CW mode)
This item adjusts the CW side tone level from 0% to
100% in 1% steps.
50%
50% (default)
See p. 43 for details.
Side Tone Level Limit (CW mode)
This item allows you to set a maximum volume level
for CW side tones. CW side tones are linked to the
[AF] control until a specified volume level is reached
— further rotation of the [AF] control will not increase
the volume of the CW side tones.
ON
OFF
CW side tone level is limited CW side tone level is linked
with [AF] (default)
to [AF]
Twin Peak Filter (RTTY mode)
This item turns the twin peak filter ON and OFF.
ON
OFF
Twin peak filter is ON
Twin peak filter is OFF.
(default)
2125
1275
2125 Hz RTTY mark
frequency (default)
1275 Hz RTTY mark
frequency
RTTY Mark Frequency (RTTY mode)
This item selects the RTTY mark frequency. RTTY
mark frequency is switched between 1275, 1615 and
2125 Hz.
RTTY Shift Width (RTTY mode)
This item adjusts the RTTY shift width. There are 3
selectable values: 170, 200 and 425 Hz.
170
425
170 Hz RTTY shift
frequency (default)
425 Hz RTTY shift
frequency
Normal
Reverse
Normal polarity
(default)
Reverse polarity
RTTY Keying Polarity (RTTY mode)
This item selects the RTTY keying polarity. Normal or
reverse keying polarity can be selected.
When reverse polarity is selected, Mark and Space
are reversed.
- Normal : Key open/close = Mark/Space
- Reverse : Key open/close = Space/Mark
123
SET MODE
13
■ Display set mode
To adjust the LCD contrast or backlight, wait until
the LCD becomes stable (10 min. or more after turning power ON). This is an inherent characteristic of
LCDs and LCD backlights and does not indicate a
transceiver malfunction.
1 Contrast (LCD)
This item adjusts the contrast of the LCD from 0% to
100% in 1% steps.
40%
40% (default)
2 Bright (LCD)
This item adjusts the brightness of the LCD from 0%
to 100% in 1% steps.
70%
70% (default)
3 LCD Unit Bright
This item adjusts the brightness of the LCD unit from
0% to 100% in 1% steps.
40%
40% (default)
4 LCD Flicker
This item adjusts the flicker of the LCD from 0% to
100% in 1% steps.
Icom recommends using the default value. But if
you find the LCD flicker objectionable, adjust this
item.
65%
65% (default)
13
5 Backlight(Switches)
This item adjusts the brightness of the switches from
0% to 100% in 1% steps.
50%
50% (default)
6 Display Type
This item sets the LCD screen type. There are 3 selectable types: A (Black-background), B (White-background), and C (Blue-background).
A
A-type LCD screen (default)
124
13
SET MODE
■ Display set mode (continued)
7 Display Font Type
Basic
This item sets the font type of the frequency readouts.
Basic and Italic (2 fonts) are selectable.
Basic font (default)
8 Display Font Size
Normal
This item sets the font size of the frequency readouts.
Normal and large (2 sizes) are selectable.
Normal size (default)
9 Meter Peak Hold
This item turns the meter peak hold function ON and
OFF.
When the meter peak hold function is ON, the highest
activated segment of the meter remains visible for 0.5
sec.; when OFF, the meter functions normally.
ON
OFF
Meter peak hold is ON
(default)
Meter peak hold is OFF
10 Filter Popup (PBT)
This item turns the popup indication ON and OFF for
the PBT function.
ON
OFF
Popup function is ON
(default)
Popup function is OFF
ON
OFF
Popup function is ON
(default)
Popup function is OFF
ON
OFF
Popup function is ON
(default)
Popup function is OFF
11 Filter Popup (FIL)
This item turns the popup indication ON and OFF for
the filter selection.
12 1Hz Mode Popup
This item turns the popup indication ON and OFF for
the 1 Hz tuning step function.
13 Scope CENTER/FIX Popup
This item turns the popup indication ON and OFF for
the Scope center/fix mode selection.
125
ON
OFF
Popup function is ON
(default)
Popup function is OFF
SET MODE
13
■ Display set mode (continued)
14 TV Popup (CH Up/Down)
This item turns the popup indication ON and OFF for
the TV channel Up/Down operation.
TV operation is available for Japanese version only.
ON
OFF
Popup function is ON
(default)
Popup function is OFF
15 TV Popup (P.AMP/ATT)
This item turns the popup indication ON and OFF for
the P.AMP/ATT setting on TV operation.
TV operation is available for Japanese version only.
ON
OFF
Popup function is ON
(default)
Popup function is OFF
ON
OFF
16 Voice TX Name Display
This item turns the indication of the voice TX memory
channel names ON and OFF on the voice TX memory channels of the voice TX menu.
Voice TX memory names Only the voice TX memory
are indicated on the voice channels are indicated.
TX memory channels. (default)
17 Keyer Memory Display
This item turns the indication of the keyer memory
contents ON and OFF on the keyer memory channels
of the memory keyer send menu.
ON
OFF
Memory contents are indi- Only the keyer memory
cated on the keyer memory channels are indicated.
channels. (default)
18 DTMF Memory Display
This item turns the indication of the DTMF code sequence ON and OFF on the DTMF memory channels
of the DTMF send menu.
ON
OFF
DTMF code sequence are Only DTMF memory chanindicated on the DTMF nels are indicated.
memory channels. (default)
13
19 External Display
This item selects the indication size for external display.
1
2
Same indication ratio as The indication width betransceiver display.
comes narrow.
(default)
20 Opening Message
This item turns the opening message screen indication capability ON and OFF.
ON
OFF
Opening message is ON
(default)
Opening message is OFF
126
13
SET MODE
■ Display set mode (continued)
21 My Call
Your call sign, etc. can be displayed in the opening
screen when turning power ON. Up to 10 characters
can be programmed.
Capital letters, numerals, some symbols (– / . ) and
space can be used.
q Push [AF(SET)] momentarily, then [F-2 DISP] to
select the display set mode.
w Push [F-1 ≤] or [F-2 ≥] several times to select the
My Call” item.
“M
r Input the desired character by rotating [DIAL] or by
pushing the band key (on HM-151) for number
input.
Y(MENU/GRP)] to select the capital letters
• Push [Y
([ABC]), numerals ([123]) or symbols ([etc]).
• Push [F-1 Å] or [F-2 Ç] for cursor movement.
• Push [F-3 DEL] to delete the selected character.
• Push [F-4 SPC] to input a space.
Z(MENU/GRP)] to input the set name.
t Push [Z
• The cursor disappears.
Z(MENU/GRP)] twice to exit the set mode
y Push [Z
screen.
• Opening screen example
e Push [F-3 EDT] to edit.
• A cursor appears and blinks.
Selected
character
22 Power ON Check
This item selects the indication ON or OFF when turning power ON.
ON : The Transceiver briefly displays ‘Your Call
sign,’ ‘RF power,’ ‘Auto power OFF timer’ and
‘RIT/∂TX frequency’ when turning power ON.
• No-programmed or disactivated items are skipped.
OFF : The display goes directly to frequency indication at power ON.
127
ON
OFF
Power ON check is ON.
(default)
Power ON check is OFF.
SET MODE
13
■ Miscellaneous (others) set mode
1 Monitor
This item sets the TX monitor function ON and OFF.
ON
The monitor gain can be set described below.
TX monitor
turned ON.
OFF
function
is TX monitor function
turned OFF. (default)
is
2 Monitor Level
This item adjusts the transmit IF signal monitor level
from 0% to 100% in 1% steps.
50%
50% (default)
See p. 87 for details.
3 Beep(Confirmation)
A beep sounds each time a switch is pushed to confirm it. This function can be turned OFF for silent operation.
ON
OFF
Confirmation beep ON
(default)
Confirmation beep OFF
ON
OFF
Band edge beep ON
(default)
Band edge beep OFF
The volume level can be set described below.
4 Beep(Band Edge)
A beep sounds when an operating frequency enters
or exits an amateur band. This functions independent
of the confirmation beep setting (above).
The volume level can be set described below.
5 Beep Level
This item adjusts the volume level for (confirmation
and band edge) beep tones from 0% to 100% in 1%
steps. When beep tones are turned OFF, this setting
has no effect.
50%
50% (default)
13
6 Beep Level Limit
This item allows you to set a maximum volume level
for (confirmation and band edge) beep tones. The
beep tones are linked to the [AF] control until a specified volume level is reached — further rotation of the
[AF] control will not increase the volume of the beep
tones.
ON
OFF
Beep level is limited with Beep level is linked to [AF]
[AF] (default)
128
13
SET MODE
■ Miscellaneous (others) set mode (continued)
7 RF/SQL Control
The [RF/SQL] control can be set as the RF/squelch
control (default), the squelch control only (RF gain is
fixed at maximum) or ‘Auto’ (RF gain control in SSB,
CW and RTTY; squelch control in AM and FM).
RF+SQL
[RF/SQL] control as RF/squelch control
SQL
[RF/SQL] control as squelch control
AUTO
[RF/SQL] control as RF gain control in SSB,
CW and RTTY; squelch control in AM and
FM (default)
See pgs. 1, 35 for details.
8 Quick SPLIT
When this item is set to ON, pushing and holding [F-1
SPL] (M
M-1) for 1 sec. sets the undisplayed VFO frequency to the displayed VFO frequency plus the split
offset and activates split operation.
ON
OFF
Quick split ON
(default)
Quick split OFF
See p. 90 for details.
9 SPLIT Offset
This item sets the offset (difference between transmit
and receive frequencies) for the quick split function.
The offset frequency can be set from –9.999 MHz to
+9.999 MHz in 1 kHz steps.
0.000MHz
-9.999MHz
0.000 MHz offset
(default)
Minus 9.999 MHz offset
ON
OFF
Split lock function ON
Split lock function OFF
(default)
10 SPLIT LOCK
When this item is ON, [DIAL] can be used to adjust
the transmit frequency while pushing and holding
[XFC] even while the lock function is activated.
See p. 89 for split frequency operation details.
11 DUP Offset HF
This item sets the offset (difference between transmit
and receive frequencies) for duplex operation. However, this setting is used to input the repeater offset
for an HF band only.
0.100MHz
0.1 MHz offset (default)
The offset frequency can be set from 0.000 MHz to
+9.999 MHz in 1 kHz steps.
12 DUP Offset 50M
This item sets the offset (difference between transmit
and receive frequencies) for duplex operation. However, this setting is used to input the repeater offset
for the 50 MHz band only.
The offset frequency can be set from 0.000 MHz to
+9.999 MHz in 1 kHz steps.
129
0.500MHz
0.5 MHz offset (default)
SET MODE
13
■ Miscellaneous (others) set mode (continued)
13 DUP Offset 144M
0.600MHz
This item sets the offset (difference between transmit
and receive frequencies) for duplex operation. However, this setting is used to input the repeater offset
for an 144 MHz band only.
0.6 MHz offset (default)
The offset frequency can be set from 0.000 MHz to
+9.999 MHz in 1 kHz steps.
14 DUP Offset 430M
5.000MHz
This item sets the offset (difference between transmit
and receive frequencies) for duplex operation. However, this setting is used to input the repeater offset
for the 430 MHz band. only
5 MHz offset (default)
The offset frequency can be set from 0.000 MHz to
+9.999 MHz in 1 kHz steps.
15 One Touch Repeater
This item turns the one touch repeater function ON
DUP-, DUP+) and OFF.
(D
When [F-2 DUP] (M-3) is pushed and held for 1 sec.,
the selected offset direction and programmed duplex
offset frequency (depending on the operating frequency band) is set with the displayed frequency.
DUP-
OFF
Minus offset direction is se- One touch repeater function
lected. (default)
is OFF.
16 Auto Repeater
This item turns the auto repeater function ON-1 (auto
duplex setting), ON-2 (auto duplex setting and activating tone encoder) or OFF.
ON-1
OFF
Auto duplex setting is ON.
Auto repeater function is
OFF.
(default)
13
See p. 65 for details concerning the auto repeater
function.
17 Tuner (Auto Start)
The optional AT-180 ANTENNA TUNER has an automatic
start capability which starts tuning if the SWR is
higher than 1.5–3:1.
When “OFF” is selected, the tuner remains OFF even
when the SWR is poor (1.5–3:1). When “ON” is selected, automatic tune starts even when the tuner is
turned OFF.
ON
OFF
Automatic tune function is Automatic tune function is
ON.
OFF. (default)
Even when “ON” is selected, automatic tune does
not start for the 50 MHz band.
130
13
SET MODE
■ Miscellaneous (others) set mode (continued)
18 Tuner (PTT Start)
When an optional AH-4 ANTENNA TUNER is connected,
tuning can be started automatically at the moment the
PTT is pushed.
This function activates for HF band only.
ON
OFF
Tuning starts when pushing Tuning starts only when
[PTT] on a new frequency.
[TUNER] is pushed. (default)
19 [TUNER] Switch
When an optional AT-180 ANTENNA TUNER is connected, the transceiver retains the [TUNER/CALL]
key ON/OFF condition for each band, “Auto,” or all
band, “Manual.”
Auto
[TUNER/CALL] key ON/OFF condition is
retained for each band. (default)
Manual
[TUNER/CALL] key ON/OFF condition is
retained for all band.
ON
VSEND is for the 144/430 MHz;
HSEND is for the HF/50 MHz. (default)
UHF Only
VSEND is for the 430 MHz;
HSEND is for the HF/50/144 MHz.
OFF
VSEND is not used;
HSEND is for all bands.
20 VSEND Select
This item select the [ACC] (pin 7) output.
21 SPEECH Level
50%
This item adjusts the volume level for speech function
from 0% to 100% in 1% steps.
50% (default)
22 SPEECH Language
This item selects language for the speech function.
English
Japanese
You can select between English and Japanese as the
SPEECH language.
English announcement
(default)
Japanese announcement
23 SPEECH Speed
This item selects the speech speed between faster or
slower synthesizer output.
131
HIGH
LOW
Faster announcement
(default)
Slower announcement
SET MODE
13
■ Miscellaneous (others) set mode (continued)
24 SPEECH S-Level
You can have frequency, mode and signal level announcement. Signal level announcement can be deactivated if desired.
ON
OFF
Signal level announcement
(default)
No signal level
announcement
ON
OFF
When “OFF” is selected, the signal level is not announced.
25 SPEECH [MODE] Switch
This item selects the operating mode speech capability when [MODE] is pushed.
When “ON” is selected, the selected operating mode
is announced at pushing [MODE].
Operating model announce- No operating mode anment with [MODE]
nouncement with [MODE]
(default)
26 Memopad Numbers
This item sets the number of memo pad channels
available. 5 or 10 memo pads can be set.
5
10
5 memo pads
(default)
10 memo pads
27 SCAN Speed
This item sets the rate at which channels or frequencies are scanned during scan operations. High and
low can be selected.
HIGH
LOW
Scan is faster.
(default)
Scan is slower.
28 SCAN Resume
This item sets the scan resume function ON and OFF.
ON
Scan resumes 10 sec. after stopping on
a signal (or 2 sec. after a signal disapper). (default)
OFF
Scan does not resume after stopping on
a signal. For the priority watch, setting to
OFF pauses the watch until the signal
disappears and scan resumes.
HIGH
Auto tuning step is turned ON.
Fastest tuning step during rapid rotation
(default)
LOW
Auto tuning step is turned ON.
Faster tuning step during rapid rotation
OFF
Auto tuning step is turned OFF.
13
29 MAIN DIAL Auto TS
This item sets the auto tuning step function. When rotating [DIAL] rapidly, the tuning step rate adapts as
selected.
There are 2 type of auto tuning steps: HIGH (Fastest)
and LOW (Faster).
132
13
SET MODE
■ Miscellaneous (others) set mode (continued)
30 HM-151 [F-1]
This item programs one of several functions to [F-1]
key of HM-151. Programmable key assignments are
described as below.
“P.AMP/ATT” (Preamplifier/attenuator),
“NB” (Noise blanker),
“NR” (Noise reduction),
“MNF” (Manual notch filter),
“ANF” (Auto notch filter),
“TS” (Tuning step),
“SPL” (Split operation),
“A/B” (VCO A/B selection),
“MCL” (Memory clear),
“BNK” (Bank selection),
“COM” (Speech compressor),
MPW
ANF
Memo pad write is pro- Auto notch filter is programmed. (default)
grammed.
“AGC” (AGC selection),
“TBW” (TX filter width),
“DUP” (Duplexer),
“TON” (FM tone operation),
“MET” (Meter selection),
“VSC” (Voice squelch control),
“MPW” (Memo pad write),
“MPR” (Memo pad read),
“<SCOPE>” (Scope selection),
“<METER>” (Multi-meter selection)
31 HM-151 [F-2]
This item programs one of several functions to [F-2]
key of HM-151. Programmable key assignments are
same as above.
MPR
NB
Memo pad read is pro- Noise blanker function is
grammed. (default)
programmed.
32 MIC Up/Down Speed
This item sets the rate at which frequencies are
Y]/[Z
Z]
scanned when the microphone (HM-151) [Y
keys are pushed and held. High or low can be selected.
HIGH
LOW
High speed (default,
5 tuning steps/sec.)
Low speed
(2.5 tuning steps/sec.)
ON
OFF
33 Quick RIT/∂TX Clear
This item selects the RIT/∂TX frequency clearing instruction for the [F-3 CLR] key.
See pgs. 73, 86 for details.
Clears the RIT/∂TX fre- Clears the RIT/∂TX frequency when [F-3 CLR ] is quency when [F-3 CLR ] is
pushed momentarily.
pushed and held for 1 sec.
(default)
34 SSB/CW Synchronous Tuning
This item selects the displayed frequency shift function from ON and OFF.
When this function is activated, the received signal
will remain the same even when the operating mode
is changed between SSB and CW.
The frequency shifting value may differ according
to the CW pitch setting.
133
ON
OFF
The displayed frequency The displayed frequency
shifts when the operating does not shift.
mode is changed between (default)
SSB and CW.
SET MODE
13
■ Miscellaneous (others) set mode (continued)
35 CW Normal Side
Selects the carrier point of CW mode from LSB and
USB.
LSB
USB
The carrier point is set to The carrier point is set to
LSB side.
USB side.
(default)
36 VOICE 1st Menu
This item selects the initial menu when [F-1 VO ]
VOICE-RX/TX ” or
S-1) is pushed, from “V
(S
VOICE-Root.”
“V
VOICE-RX/TX
VOICE-Root
Voice RX/TX menu is se- Voice root menu is selected.
lected. (default)
37 KEYER 1st Menu
This item selects the initial menu when [F-2 KEY ]
KEYER-SEND ”
S-1) is pushed, from “K
or
(S
KEYER-Root.”
“K
KEYER-SEND
KEYER-Root
Keyer send menu is se- Keyer root menu is selected.
lected. (default)
38 DTMF 1st Menu
This item selects the initial menu when [F-2 DTM]
S-1) is pushed, from “D
DTMF-SEND” or “D
DTMF(S
Root.”
DTMF-SEND
DTMF-Root
DTMF send menu is se- DTMF root menu is selected. (default)
lected.
39 Mode Select (SSB)
This item inhibits the selection of SSB (LSB/USB)
modes, and allows you to simplify operation during
normal operation.
ON
OFF
SSB modes are selectable.
(default)
SSB modes are inhibited.
For example if you are operating mobile and only plan
on using FM and AM modes, sets all other modes
(SSB, CW, RTTY, WFM) to OFF, thereby making selection of AM or FM quick and easy.
13
40 Mode Select (CW)
This item inhibits the selection of CW/CW-R modes,
and allows you to simplify operation during normal operation.
ON
OFF
CW modes are selectable.
(default)
CW modes are inhibited.
ON
OFF
41 Mode Select (RTTY)
This item inhibits the selection of RTTY/RTTY-R
modes, and allows you to simplify operation during
normal operation.
RTTY modes are selectable. RTTY modes are inhibited.
(default)
134
13
SET MODE
■ Miscellaneous (others) set mode (continued)
42 Mode Select (AM)
This item inhibits the selection of AM mode, and allows you to simplify operation during normal operation.
ON
OFF
AM mode is selectable.
(default)
AM mode is inhibited.
ON
OFF
FM mode is selectable.
(default)
FM mode is inhibited.
43 Mode Select (FM)
This item inhibits the selection of FM mode, and allows you to simplify operation during normal operation.
44 Mode Select (WFM)
This item inhibits the selection of WFM mode, and allows you to simplify operation during normal operation.
ON
OFF
WFM mode is selectable.
(default)
WFM mode is inihibited.
45 External Keypad (VOICE)
This item sets the external keypad capability and
function.
For your information
The following diagram shows the equivalent circuit of
an external keypad and connects to the pin 2 and
pin 7 of the [MIC] connector (p. 10).
4.7kΩ
±5%
S4
(T4/M4)
2.2kΩ
±5%
S3
(T3/M3)
1.5kΩ
±5%
1.5kΩ
±5%
S2
(T2/M2)
S1
(T1/M1)
To [MIC] connector pin w
ON
: Pushing one of external keypad switches, transmits
the desired voice memory contents (during a phone
mode (SSB, AM, FM) operation.
OFF : External keypad does not function.
(default)
If you want to transmit a message using the external keypad descrived at left, you must set “47
Front Keypad Type” (p. 136) to “Ext
Keypad,” and record the desired message in
transmit voice memory channels T1—T4 in advance (p.96).
To [MIC] connector pin u
USER EXTERNAL KEYPAD
46 External Keypad (KEYER)
This item sets the external keypad capability and
function.
User external keypad is same as above.
ON
: Pushing one of external keypad switches, transmits
the desired memory keyer contents during CW
mode operation.
OFF : External keypad does not function. (default)
If you want to transmit a memory keyer contents
using the external keypad descrived above, you
must set “47 Front Keypad Type” (p. 136)
to “Ext Keypad.”
135
SET MODE
13
■ Miscellaneous (others) set mode (continued)
47 Front Keypad Type
This item selects the keypad type that connected to
the [MIC] connector.
Dot/Dash
Ext Keypad
Dot/Dash (default)
External keypad
Auto
19200
Auto baud rate
(default)
19200 bps
48 CI-V Baud Rate
This item sets the data transfer rate. 300, 1200, 4800,
9600, 19200 bps and “Auto” are available.
When “Auto” is selected, the baud rate is automatically set according to the connected controller or remote controller.
49 CI-V Address
To distinguish equipment, each CI-V transceiver has
its own Icom standard address in hexadecimal code.
The IC-7000’s address is 70h.
70h
7Fh
Address of 70h
(default)
Address of 7Fh
When 2 or more IC-7000’s are connected to an optional CT-17 CI-V LEVEL CONVERTER, rotate [DIAL] to
select a different address for each IC-7000 in the
range 01h to 7Fh.
50 CI-V Transceive
Transceive operation is possible with the IC-7000 connected to other Icom HF transceivers or receivers.
When “ON” is selected, changing the frequency, operating mode, etc. on the IC-7000 automatically
changes those of connected transceivers (or receivers) and vice versa.
ON
OFF
Transceive ON
(default)
Transceive OFF
13
51 REF Adjust
This item adjusts the internal reference frequency
within 0 to 100% range in 1 % steps.
136
14
MAINTENANCE
■ Fuse replacement
DC power cable fuse replacement
If a fuse blows or the transceiver stops functioning, try
to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse.
CAUTION: Disconnect the DC power cable from
the transceiver when changing a fuse.
The IC-7000 has three fuses (DC power cable fuses ×
2, circuitry fuse × 1) installed for transceiver protection.
• DC power cable fuses ........................... ATC20 30 A
• Circuitry fuse ............................................ ATC20 5 A
CIRCUITRY FUSE REPLACEMENT
The 13.8 V DC from the DC power cable is applied to
all units in the IC-7000, except for the power amplifier, through the circuitry fuse. This fuse is installed in
the FRONT unit.
R WARNING: NEVER attempt to remove fuse
cover using your finger nails, this may result in injury.
Screw driver
Fuse cover
Fuse
■ Memory backup
All of the CPU’s memory is backed up by an EEPROM (Electronically-Erasable Programmable ReadOnly Memory). All data you set, such as VFO,
memory, set mode contents, etc. are stored in this
EEPROM. There is no internal lithium battery.
■ Cleaning
If the transceiver becomes dusty or dirty,
wipe it clean with a dry, soft cloth.
137
AVOID the use of strong chemical solvents
such as thinner, benzine or alcohol to clean
the transceiver. These may damage the
transceiver’s surfaces.
TROUBLESHOOTING
The following chart is designed to help you correct
problems which are not equipment malfunctions.
POWER SUPPLY
PROBLEM
Power does not come
on when [PWR] key is
pushed.
If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact your nearest Icom Dealer or Service Center.
POSSIBLE CAUSE
DC power
connected.
cable
is
15
improperly
Fuse is blown.
SOLUTION
REF.
Reconnect the power cable correctly.
p. 19
Check for the cause, then replace the p. 137
fuse with a spare one.
(Fuses are installed in two places. One is
installed in the DC power cable and the
other is installed in the FRONT unit.
No sound comes from
the speaker.
RECEIVE
Sensitivity is low.
Receive audio is distorted.
Receive signal is distorted by strong signals.
Battery is exhausted if you are using
a 12 V battery as the power source.
Check the battery voltage.
Volume level is set too low.
Rotate [AF] clockwise to obtain a suit- pgs. 1,
25, 33
able listening level.
The squelch is closed.
Rotate [SQL] counterclockwise to pgs. 1,
25, 35
open the squelch.
The transceiver is in transmit mode.
Release [PTT] on the microphone or —
check the SEND line of an external
unit, if connected.
An external speaker or headphones
are connected.
Check the external speaker or head- p. 18
phone plug connection.
The antenna is not connected properly.
Reconnect to the antenna connector.
—
The antenna feed line is cut or shorted.
Check the feed line and correct any
improper conditions.
—
The antenna is not properly tuned.
Push [TUNER/CALL] to manually pgs.
tune the antenna.
114, 115
The attenuator function is activated.
Push [P.AMP/ATT]
function OFF.
The operating mode is not selected
correctly.
Select a suitable operating mode.
The PBT function is activated.
Push [PBT/M-ch/RIT(CLR)] for 1 sec. p. 77
to clear the PBT function.
Noise blanker function is activated.
Push [NB/ADJ] to turn the function p. 78
OFF.
Preamp is activated.
Push [P.AMP/ATT]
function OFF.
to
to
—
turn
turn
the p. 72
p. 34
14
15
the p. 72
138
15
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
TRANSMIT
DISPLAY
SCAN
REF.
Transmitting is impossible.
The operating frequency is not set to
a ham band.
Set the frequency to a ham band.
Output power is too low.
Power is set to a lower power than
maximum.
Set the output power in quick set p. 38
mode.
Microphone gain is set too low.
Set microphone gain to a suitable p. 38
position using quick set mode.
The antenna is not connected properly.
Reconnect the antenna connector.
—
The antenna feed line is cut or shorted.
Check the feed line and correct any
improper conditions.
—
The antenna is not properly tuned.
Push [TUNER/CALL] to manually pgs.
114, 115
tune the antenna.
RIT function is activated.
Push [F-1 RIT] in the RIT/∂TX mode p. 73
to turn the function OFF.
Split function is activated.
Push [F-1 SPL] in the M-1 menu to turn p. 89
the function OFF.
Split function is not activated.
Push [F-1 SPL] in the M-1 menu to turn p. 89
the function ON.
An incorrect transmit frequency is set.
Set the proper frequencies into VFO pgs.
A and B or into one of the memory 27, 29
channels.
Subaudible tone encoder is OFF and
repeater requires a tone for access.
Use [F-3 TON] in the M-3 menu to se- p. 63
lect FM-TONE.
Programmed subaudible tone frequency is wrong.
Program the required frequency using p. 64
FM tone set mode.
Transmitted signals are
distorted.
Microphone gain is set too high.
Set MIC gain in quick set mode.
The compression level is set too high
with the speech compressor ON.
Set compression level to a suitable p. 88
position.
Displayed
frequency
does not change properly.
The dial lock function is activated.
Push [SPCH/LOCK] to deactivate the p. 37
function.
The internal CPU has malfunctioned.
Reset the CPU.
No contact possible with
other stations.
139
SOLUTION
Repeater cannot be accessed.
p. 29
p. 38
p. 25
(While pushing [Y(BAND)] and [Z(BAND)],
push [PWR] to turn power ON.
p. 35
Programmed scan does
not stop.
Squelch is open.
Set squelch to the threshold position.
Programmed scan does
not start.
The same frequencies have been
programmed in scan edge memory
channels.
Program different frequencies into p. 101
scan edge memory channels.
Memory scan does not
start.
2 or more memory channels have not
been programmed.
Program 2 or more memory chan- p. 101
nels.
Memory select
does not start.
2 or more memory channels have not
been designated as select channels.
Designate 2 or more memory chan- p. 104
nels as select channels for the scan.
scan
OPTION UNITS SETTING
16
■ MB-106 CARRYING HANDLE
The optional MB-106 CARRYING HANDLE is convenient
when carrying the transceiver for DX’ peditions, field
operation, etc.
q Attach the rubber feet with the supplied screws as
shown below.
w Attach the MB-106 to the left side of the transceiver
as shown below.
Carrying
handle
Rubber
feet
■ Band voltage modification
If you want to connect an external unit which can be
controlled by the band voltage from [ACC] connector, the following modification is necessary. The band
voltage appears on pin 5 of [ACC] connector after
modification is completed.
Performing this modification is the customer’s responsibility. Icom does not guarantee this modification’s result.
IC-7000’s top view with DDS unit
top panel is opened
Cooling
fan
Front panel
CAUTION: Disconnect the DC power cable
from the transceiver before any work on the transceiver.
Bridge these
solder pads
• Band voltage generator circuit
15
The below circuit is just for reference.
ACC socket of
an optional unit
GND
6
7
8V
1
3
5
2
4700 pF
4
100 µH
1.9 MHz
Diode
BAND
100 µH
4700 pF
Extenal
power souce
8V
4.7 kΩ
VR
4.7 kΩ 3.5 MHz
VR
4.7 kΩ 7 MHz
10 MHz
Open
10 kΩ 14 MHz
VR
4700 pF
VR
10 kΩ
18/21 MHz
OR
22 kΩ
24/28 MHz
Rotary
switch
The following band voltage table is for reference only.
Please adjust and confirm against the actual operating condition.
BAND
VOLTAGE
1.9 MHz
3.5 MHz
7 MHz
10 MHz
14 MHz
18/21 MHz
24/28 MHz
—
6.1 V
5.1 V
—
4.1 V
3.1 V
2.1 V
16
140
16
OPTION UNITS SETTING
■ AT-180 internal switch description
The optional AT-180 has 3 operating configurations
for HF band operation. Select a suitable configuration
according to your antenna system.
q Remove the top cover of the AT-180.
w Set the tuner switches to the desired positions according to the table below.
• AT-180 inside top cover
SW Position
Operation
S1
The tuner operating condition is set by S2
A
(default) described below.
B
S2
C
THROUGH INHIBIT
The tuner tunes the antenna even when the
antenna has poor SWR (up to VSWR 3:1
after tuning). In this case, manual tuning is
necessary each time you change the frequency although the tuner automatically
starts tuning when the VSWR is higher than
3:1. This setting is called “through inhibit,”
however, the tuner is set to “through” if the
VSWR is higher than 3:1 after tuning.
TUNER SENSITIVE CONDITION
The tuner tunes each time you transmit (except SSB mode). Therefore, the lowest
SWR is obtained at any given time.
For SSB mode, the same condition as the
“D” position.
• Specifications for the AT-180
• Frequency coverage : 1.9–54 MHz
• Input impedance
: 50 Ω
• Maximum input
: 120 W
power
• Minimum tuning
:8W
power
• Matching impedance : 16.7–150 Ω (HF band)
range
20–125 Ω (50 MHz band)
• Tuning accuracy
: Less than SWR 1.5:1
• Insertion loss
: Less than 1.0 dB
(after tuning)
• Power supply
requirements
• Dimensions (mm/in)
the transceiver’s ACC socket)
: 167(W) × 58.6(H) × 225(D)
69⁄16(W) × 25⁄17(H) × 87⁄8(D)
• Weight
: 2.4 kg; 5 lb 4 oz
• Supplied accessories : Coaxial cable (1 m),
ACC cable (DIN 13 pins)
• Connector information for ACC(2) socket
4
2
1
6
NORMAL CONDITION
The tuner tunes when the SWR is higher
(default) than 1.5:1. Therefore, the tuner activates
only when tuning is necessary.
: 13.8 V DC/1 A (supplied from
5
3
ACC 2
7
D
141
S2
S1
D C
B A
PIN NO./
NAME
DESCRIPTION
q8 V
Regulated 8 V output.
(10 mA max.)
w GND
Connects to ground.
e SEND
Input/output pin.
Goes to ground when transmitting (20 mA
max). When grounded, transmits.
r BAND
Band voltage output.
(Varies with amateur band; 0 to 8.0 V).
t ALC
ALC output voltage (–4 to 0 V).
y NC
No connection.
u 13.8V
13.8 V output when power is ON (1 A max).
17
CONTROL COMMAND
■ Remote jack (CI-V) information
D CI-V connection example
9–15 V DC
The transceiver can be connected through an optional
CT-17 CI-V LEVEL CONVERTER to a personal computer
equipped with an RS-232C port. The Icom Communication interface-V (CI-V) controls the following functions of the transceiver.
Up to four Icom CI-V transceivers or receivers can be
connected to a personal computer equipped with an
RS-232C port. See p. 136 for setting the CI-V condition using the miscellaneous (others) set mode.
Personal
computer
IC-7000
D Data format
mini-plug cable
The CI-V system can be operated using the following
data formats. Data formats differ according to command numbers. A data area is added for some commands.
Data area
FE FE
70
E0
FD
End of message code (fixed)
FD
FB
OK code
(fixed)
Sc
E0
Controller’s default address
Cn
70
Transceiver’s default address
70
FE FE
Preamble code (fixed)
E0
FD
End of message code (fixed)
FE FE
Data area
BCD code data for frequency
or memory number entry
Sub command number
(see table below)
Sc
Command number
(see table below)
Cn
Controller’s default address
E0
Transceiver’s default address
70
Preamble code (fixed)
FE FE
OK MESSAGE TO CONTROLLER
NG code
(fixed)
CONTROLLER TO IC-7000
FA
FD
NG MESSAGE TO CONTROLLER
IC-7000 TO CONTROLLER
D Command table
Command
Sub command
Description
Command
Sub command
Send frequency data
07
B0
Exchange VFO A and VFO B
Send mode data
08
—
Select memory mode
00
—
01
Same as
command 06
02
—
Read band edge frequencies
03
—
Read operating frequency
04
—
Read operating mode
05
—
Set operating frequency
06
00
01
02
03
04
05
07
08
Select LSB
Select USB
Select AM
Select CW
Select RTTY
Select FM
Select CW-R
Select RTTY-R
—
00
01
A0
Select VFO mode
Select VFO A
Select VFO B
Equalize VFO A and VFO B
07
09
Description
0001–0105*
Select memory channel
*P1=0100, P2=0101
0106, 0107
Select the call channel
(C1=0106, C2=0107)
16
A0
Set the bank number
(1=A, 2=B, 3=C, 4=D, 5=E)
17
—
Memory write
0A
—
Memory to VFO
0B
—
Memory clear
0C
—
Read offset frequency
0D
—
Set offset frequency
0E
00
01
02
22
23
Scan stop
Programmed/memory scan start
Programmed scan start
Memory scan start
Select memory scan start
142
17
CONTROL COMMAND
• Command table (continued)
Command
Sub command
0E
B0
B1
D0
D3
Set as non-select channel
Set as select channel
Set scan resume OFF
Set scan resume ON
0F
00
01
10
11
12
Turn the split function OFF
Turn the split function ON
Select simplex operation
Select –DUP operation
Select +DUP operation
00
AM/FM/WFM modes:
Select 10 Hz tuning step
SSB/CW/RTTY modes: TS OFF
01
02
03
04
05
06
07
08
09
Select 100 Hz tuning step
Select 1 kHz tuning step
Select 5 kHz tuning step
Select 9 kHz tuning step
Select 10 kHz tuning step
Select 12.5 kHz tuning step
Select 20 kHz tuning step
Select 25 kHz tuning step
Select 100 kHz tuning step
10
AM/FM/WFM modes:
Select MHz step
SSB/CW/RTTY modes: Invalid
Select/read attenuator (0=OFF,
12=ON (12 dB))
10
11
—
13
00
01
02
14
143
Description
Command
14
Description
15
01
02
11
12
13
14
Read squelch condition
Read S-meter level
Read RF power meter
Read SWR meter
Read ALC meter
Read COMP meter
16
02
Preamp (0=OFF; 1=ON)
12
AGC selection
(1=Fast; 2=Mid; 3=Slow)
Noise blanker (0=OFF; 1=ON)
Noise reduction (0=OFF; 1=ON)
Auto notch (0=OFF; 1=ON)
Repeater tone (0=OFF; 1=ON)
Tone squelch (0=OFF; 1=ON)
Speech compressor (0=OFF; 1=ON)
Monitor (0=OFF; 1=ON)
VOX function (0=OFF; 1=ON)
Break-in (0=OFF; 1=semi breakin; 2=full break-in)
Manual notch (NF1) (0=OFF; 1=ON)
DTCS (0=OFF; 1=ON)
VSC (0=OFF; 1=ON)
Twin Peak Filter (0=OFF; 1=ON)
Dial lock function (0=OFF, 1=ON)
Manual notch (NF2) (0=OFF, 1=ON)
22
40
41
42
43
44
45
46
47
Announce with voice synthesizer
(00=all data; 01=frequency and
S-meter level; 02=receive mode)
01 + Level data [AF] level setting (0=max. CCW to
255=max. CW)
02 + Level data [RF] level setting (0=max. CCW to
255=11 o’clock)
03 + Level data [SQL] level setting (0=11 o’clock to
255=max. CW)
06 + Level data NR level setting (0=min. to
255=max.)
07 + Level data Inside [PBT] setting or IF shift
setting (0=max. CCW, 128=center, 255=max. CW)
08 + Level data Outside [PBT] setting
(0=max. CCW, 128=center,
255=max. CW)
09 + Level data CW Pitch setting (0=300 Hz,
128=600 Hz, 255=900 Hz, in 5 Hz
steps)
0A + Level data RF Power setting (0=mini. to
255=max.)
0B + Level data MIC Gain setting (0=mini. to
255=max.)
0C + Level data Key Speed setting (0=slow to
255=fast)
0D + Level data NOTCH (NF1) frequency setting
(0=low freq. to 255=high freq.)
0E + Level data COMP Level setting (0=0 to
10=10)
0F + Level data Break-IN DELAY setting (20=2.0d
to 130=13.0d)
12 + Level data NB level setting (0=0 to
255=100%)
15 + Level data Monitor gain setting (0=0 to
255=100%)
16 + Level data VOX gain setting (0=0 to
255=100%)
Sub command
17 + Level data Anti-VOX gain setting (0=0 to
255=100%)
18 + Level data Contrast (LCD) setting (0=0 to
255=100%)
19 + Level data Bright (LCD) setting (0=0 to
255=100%)
1A + Level data NOTCH (NF2) frequency setting
(0=low freq. to 255=high freq.)
48
4B
4C
4F
50
51
19
00
Read the transceiver ID
1A
00
Send/read memory contents (see
p. 146 for details)
Send/read band stacking register
contents (see p. 146 for details)
Send/read memory keyer contents
(see p. 146 for details)
Send/read the selected filter width
(SSB, CW, RTTY:
0=50 Hz to 40/31=3600/2700 Hz;
AM: 0=200 Hz to 49=10 kHz)
Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec. to
13=6.0/8.0 sec.)
RF Power setting (0=mini. to
255=max.)
MIC Gain setting (0=mini. to
255=max.)
Send/read of SSB TX bandwidth
(lower edge) for wide
(0=100, 1=200, 2=300, 3=500 HZ)
Send/read of SSB TX bandwidth
(higher edge) for wide (0=2500,
1=2700, 2=2800, 3=2900 HZ)
Send/read of SSB TX bandwidth
(lower edge) for middle
(0=100, 1=200, 2=300, 3=500 HZ)
Send/read of SSB TX bandwidth
(higher edge) for middle (0=2500,
1=2700, 2=2800, 3=2900 HZ)
01
02
03
04
050001
050002
050003
050004
050005
050006
CONTROL COMMAND
17
• Command table (continued)
Command
Sub command
Description
Command
Sub command
Description
1A
050007
Send/read of SSB TX bandwidth
(lower edge) for narrow
(0=100, 1=200, 2=300, 3=500 HZ)
Send/read of SSB TX bandwidth
(higher edge) for narrow (0=2500,
1=2700, 2=2800, 3=2900 HZ)
Twin Peak Filter (0=OFF; 1=ON)
Send/read RTTY mark frequency
(0=1275 Hz, 1=1615 Hz,
2=2125 Hz)
Send/read RTTY shift width
(0=170 Hz, 1=200 Hz, 2=425 Hz)
Send/read RTTY keying polarity
(0=Normal, 1=Reverse)
Send/read CW key speed (0=0.6
WPM to 255=60 WPM)
Send/read CW Pitch setting
(0=300 Hz, 120=900 Hz, in 5 Hz
steps)
Send/read CW side tone level
(0=min. to 255=max.)
Send/read CW side tone level limit
(0=OFF, 1=ON)
Send/read LCD contrast (0=0% to
255=100%)
Send/read LCD bright (0=0%,
255=100%)
Send/read LCD unit bright (0=0%
to 255=100%)
Send/read LCD flicker level (0=0%
to 255=100%)
Send/read switch backlight (0=0%
to 255=100%)
Send/read display type (0=A, 1=B,
2=C)
Send/read display font type
(0=Basic, 1=Italic)
Send/read display font size
(0=Normal, 1=Large)
Send/read meter peak hold
(0=OFF, 1=ON)
Send/read filter pop up indication
for PBT shifting (0=OFF, 1=ON)
Send/read filter pop up indication
for IF filter setting (0=OFF, 1=ON)
Send/read pop up indication for 1
Hz mode (0=OFF, 1=ON)
Send/read pop up indication for
scope center/fix (0=OFF, 1=ON)
Send/read TV pop up indication for
channel Up/Down (0=OFF, 1=ON)
Send/read TV pop up indication for
P.AMP/ATT (0=OFF, 1=ON)
Send/read indication of the voice
TX memory channel names
(0=OFF, 1=ON)
Send/read indication of the keyer
memory names (0=OFF, 1=ON)
Send/read indication of the DTMF
memory names (0=OFF, 1=ON)
Send/read external display setting
(0=1:1.8, 1=1:1.6)
1A
050036
Send/read opening message
(0=OFF, 1=ON)
Send/read my call sign setting (10
character: see p. 147 )
Send/read power ON check
(0=OFF, 1=ON)
Send/read current year (2000 to
2099)
Send/read current date (0101 to
1231=Jan. 1st to Dec. 31st)
Send/read current time (0000 to
2359=00:00 to 23:59)
Send/read clock2 function (0=OFF,
1=ON)
Send/read offset time for clock2
function (24001 to 24000=–24:00
to +24:00)
Send/read auto power OFF period
(0=OFF, 1=30 min., 2=60 min.,
3=90 min.)
Send/read TX monitor set
(0=OFF, 1=ON)
Send/read TX monitor gain
(0=0% to 255=100%)
Send/read confirmation beep
(0=OFF, 1=ON)
Send/read band edge beep
(0=OFF, 1=ON)
Send/read beep gain (0=min. to
255=max.)
Send/read beep gain limit (0=OFF,
1=ON)
Send/read RF/SQL control set
(0=Auto, 1=SQL, 2=RF+SQL)
Send/read quick split set (0=OFF,
1=ON)
Send/read split offset –9.999 to
+9.999 MHz (see p. 147 for details)
Send/read split lock set (0=OFF,
1=ON)
Send/read duplex offset 0.000 to
9.999 MHz for HF (see p. 147 for
details)
Send/read duplex offset 0.000 to
9.999 MHz for 50 MHz band (see
p. 147 for details)
Send/read duplex offset 0.000 to
9.999 MHz for 144 MHz band
(see p. 147 for details)
Send/read duplex offset 0.000 to
9.999 MHz for 430 MHz band
(see p. 147 for details)
050008
050009
050010
050011
050012
050013
050014
050015
050016
050017
050018
050019
050020
050021
050022
050023
050024
050025
050026
050027
050028
050029
050030
050031
050032
050033
050034
050035
050037
050038
050039
050040
050041
050042
050043
050044
050045
050046
050047
050048
050049
050050
050051
050052
050053
050054
050055
050056
050057
050058
050059
050060
050061
050062
17
Send/read one touch repeater set
(0=DUP–, 1=DUP+)
Send/read auto repeater set
(0=OFF, 1=ON-1, 2=ON-2)
Send/read tuner auto start set
(0=OFF, 1=ON)
Send/read PTT tune set (0=OFF,
1=ON)
CW: Clockwise, CCW: Counter Clockwise
144
17
CONTROL COMMAND
• Command table (continued)
Command
Sub command
Description
Command
Sub command
Description
1A
050063
Send/read [TUNER/CALL] key action set (0=Manual, 1=Auto)
Send/read [ACC] (pin 7) output
“VSEND” set (0=OFF, 1=UHF
only, 2=ON)
Send/read speech level (0=0 to
255=100%)
Send/read speech language
(0=English, 1=Japanese)
Send/read speech speed (0=Slow,
1=Fast)
Send/read S-level speech
(0=OFF, 1=ON)
Send/read speech capability with
[MODE] key operation
(0=OFF, 1=ON)
Send/read memopad numbers
(0=5 ch, 1=10 ch)
Send/read scan speed
(0=Low, 1=High)
Send/read scan resume
(0=OFF, 1=ON)
Send/read main dial auto TS
(0=OFF, 1=Low, 2=High)
Send/read [F-1] key assigment of
the HM-151. (0=“P.AMP/ATT,”
1=“NB,”
2=“NR,”
3=“MNF,”
4=“ANF,”
5=“TS,”
6=“SPL,”
7=“A/B,” 8=“MCL,” 9=“BNK,”
10=“COM,” 11=“AGC,” 12=“TBW,”
13=“DUP,” 14=“TON,” 15=“MET,”
16=“VSC,” 17=“MPW,” 18=“MPR,”
19=“<SCOPE>,” 20=“<METER>”)
Send/read [F-2] key assigment of
the HM-151. (Selectable functions
are same as [F-1].)
Send/read mic. up/down speed
(0=Low, 1=High)
Send/read quick RIT/∂TX clear
function (0=OFF, 1=ON)
Send/read SSB/CW synchronous
tuning function (0=OFF, 1=ON)
Send/read CW normal side set
(0=LSB, 1=USB)
Send/read voice recorder 1st
menu set (0=Voice-root, 1=VoiceRX/TX)
Send/read keyer 1st menu set
(0=Keyer-root, 1=Keyer-send)
Send/read DTMF 1st menu set
(0=DTMF-root, 1=DTMF-send)
Send/read SSB mode selectability
(0=OFF: inhibition, 1=ON: selectable)
Send/read CW mode selectability
(0=OFF: inhibition, 1=ON: selectable)
Send/read RTTY mode selectability. (0=OFF: inhibition, 1=ON: selectable)
Send/read AM mode selectability
(0=OFF: inhibition, 1=ON: selectable)
1A
050087
Send/read FM mode selectability
(0=OFF: inhibition, 1=ON: selectable)
Send/read WFM mode selectability (0=OFF: inhibition, 1=ON: selectable)
Send/read external keypad set
for voice memory (0=OFF, 1=ON)
Send/read external keypad set
for keyer memory (0=OFF, 1=ON)
Send/read external keypad type
connected to [MIC] connector of
controller (0=Dot/Dash type,
1=Ext Keypad)
Send/read CI-V transceive set
(0=OFF, 1=ON)
Send/read reference frequency
set (0=0 to 255=100%)
Send/read speech compresser
level (0=0 to 10=10)
Send/read auto voice monitor set
(0=OFF, 1=ON)
Send/read MIC memo function
(0=OFF, 1=ON)
Send/read contest number style
(0=Normal, 1=190→ANO,
2=190→ANT, 3=90→NO,
4=90→NT)
Send/read count up trigger channel (1=M1, 2=M2, 3=M3, 4=M4)
Send/read present number
(1–9999)
Send/read CW keyer repeat time
(1=1 sec. to 60=60 sec.)
Send/read CW keyer dot/dash
ratio (28=1:1:2.8 to 45=1:1:4.5)
Send/read rise time (0=2 msec.,
1=4 msec., 2=6 msec.,
3=8 msec.)
Send/read CW paddle polarity
(0=Normal, 1=Reverse)
Send/read CW keyer type
(0=Straight, 1=Bug-key, 2=ELECKey)
Send/read MIC up/down keyer
(HM-103) set (0=OFF, 1=ON)
Send/read RTTY decode USOS
(0=OFF, 1=ON)
Send/read RTTY decode new line
code (0=CR,LF,CR+LF, 1=CR+LF)
Send/read scope max. hold
(0=OFF, 1=ON)
Send/read scope size set (0=Normal, 1=Wide)
Send/read fast sweep set
(0=1 sweep, 1=Continuous)
Send/read fast sweep audio level
(0=0 dB, 1=–10 dB, 2=OFF)
Send/read NB level set
(0=min. to 255=max.)
Send/read NB width set
(0=min. to 255=max.)
050064
050065
050066
050067
050068
050069
050070
050071
050072
050073
050074
050075
050076
050077
050078
050079
050080
050081
050082
050083
050084
050085
050086
145
050088
050089
050090
050091
050092
050093
050094
050095
050096
050097
050098
050099
050100
050101
050102
050103
050104
050105
050106
050107
050108
050109
050110
050111
050112
050113
CONTROL COMMAND
• Command table (continued)
Command
Sub command
Description
1A
050114
Send/read NR level set
(0=0 to 15=15)
Send/read VOX gain (0=0% to
255=100%)
Send/read anti VOX gain (0=0% to
255=100%)
Send/read VOX delay (0=0.0 sec.
to 20=2.0 sec.)
Send/read DTMF speed set
(0=100 msec., 1=200 msec.,
2=300 msec., 3=500 msec.)
Send/read Break-IN delay set
(20=2.0d to 130=13.0d)
050115
050116
050117
050118
050119
06
Send/read SSB transmit bandwidth (0=WIDE, 1=MID, 2=NAR)
07
Send/read DSP filter shape
(0= sharp, 1= soft)
08
Send/read manual notch filter1
bandwidth
(0=WIDE, 1=MID, 2=NAR)
09
Send/read manual notch filter2
bandwidth
(0=WIDE, 1=MID, 2=NAR)
0A
Send/read 9600 bps mode set
(0=OFF, 1=ON)
1B
00
01
02
1C
00
01
Set/read repeater tone frequency
(see p. 147 for details)
Set/read TSQL tone frequency
(see p. 147 for details)
Set/read DTCS code and polarity
(see p. 147 for details)
Set/read the transceiver’s condition (0=Rx; 1=Tx)
Set/read antenna tuner condition
(0=OFF, 1=ON, 2=Start tuning or
while tuning)
CW: Clockwise, CCW: Counter Clockwise
17
D To send/read memory contents
When sending or reading memory contents, an additional
code as follows must be added to specify the memory channel.
➥ Additional code: 0000–0102 (0100=P1, 0101=P2, 0102=Call)
D Band stacking register
To send or read the desired band stacking register’s contents, a combination of the frequency band and register
codes as follows are used.
For example, when sending/reading the oldest contents in
the 21 MHz band, the code “0703” is used.
• Frequency band codes
Code Frequency band Frequency range (unit: MHz)
01
1.8
1.800000– 1.999999
02
3.5
3.400000– 4.099999
03
7
6.900000– 7.499999
04
10
9.900000–10.499999
05
14
13.900000–14.499999
06
18
17.900000–18.499999
07
21
20.900000–21.499999
08
24
24.400000–25.099999
09
28
28.000000–29.999999
10
50
50.000000–54.000000
11
144
144.000000–148.000000
12
430
430.000000–450.000000
13
GENE
Other than above
• Register codes
Code
01
02
03
Register number
1 (latest)
2
3 (oldest)
D Codes for memory keyer contents
To send or read the desired memory keyer contents, the
channel and character codes as follows are used.
• Channel codes
Code
01
02
03
04
Channel number
M1
M2
M3
M4
• Character codes
Character ASCII code
Description
0–9
30–39
Numerals
A–Z
41–5A
Alphabetical characters
space
20
Word space
/
2F
Symbol
?
3F
Symbol
,
2C
Symbol
.
2E
Symbol
^
5E
e.g., to send BT, enter ^4254
✱
2A
Inserts contact number (can be
used for 1 channel only)
17
146
CONTROL COMMAND
@
40
1 MHz digit: 0—4
10 kHz digit: 0—9
XX
Direction:
00=+ direction
01=— direction
X
*No need to enter for duplex frequency setting.
D Repeater tone/tone squelch frequency
setting
0
X
X
X
X
0.1 Hz digit: 0–9
0
1 Hz digit: 0–9
The following data sequence is used when sending/reading
the DTCS code and polarity setting.
q*
w
e
*Not necessary when setting a frequency.
D DTCS code and polarity setting
The following data sequence is used when sending/reading
the DTCS code and polarity setting.
0
X
X
X
2nd digit: 0–7
3rd digit: 0–7
e
1st digit: 0–7
X
Transmit polarity:
0= Normal
1= Reverse
Receive polarity:
0= Normal
1= Reverse
X
w
Fixed digit: 0
q
147
r*
0
10 MHz digit: 0 (fixed)
X
10 Hz digit: 0–9
ASCII code
23
25
5C
22
60
2D
3B
3C
28
5B
7B
7C
7E
e
X
100Hz digit: 0–2
• Character codes— Symbols
Character
ASCII code
Character
!
21
#
$
24
%
&
26
¥
?
3F
”
’
27
`
+
2B
–
:
3A
;
=
3D
<
>
3E
(
)
29
[
]
5D
{
}
7D
|
–
_
5F
w
0
100 kHz digit: 0—9
D Codes for memory name contents
To send or read the desired memory name settings, the character codes, instruction codes for memory keyer contents as
above, and the following are used.
• Character codes— Alphabetical characters
Character
ASCII code
Character
ASCII code
a–z
61–7A
—
—
q
X
Fixed digit: 0*
Description
Numerals
Alphabetical characters
Word space
Symbol
Symbol
Symbol
100 Hz digit: 0 (fixed)
Character ASCII code
0–9
30–39
A–Z
41–5A
space
20
–
2D
.
2E
/
2F
D Split/Duplex frequency setting
The following data sequence is used when sending/reading
the split or duplex frequency setting.
Fixed digit: 0*
D Character codes for My Call
1 kHz digit: 0—9
17
SPECIFICATIONS
■ General
• Frequency coverage :
Receive
30 kHz–199.999999 MHz*1*2
400–470.000000 MHz*1*2
Transmit
1.800–1.999999 MHz*2, 3.500–3.999999 MHz*2
5.33050*3, 5.34650*3, 5.36650*3,
5.37150*3, 5.40350*3,
7.000–7.300 MHz*2,
10.100–10.150 MHz*2,
14.000–14.350 MHz*2, 18.068–18.168 MHz*2,
21.000–21.450 MHz*2, 24.890–24.990 MHz*2,
28.000–29.700 MHz*2, 50.000–54.000 MHz*2,
144.000–148.000 MHz*2, 430.000–450.000 MHz*2
*1Some frequency bands are not guaranteed.
*2Depending on version.
*3USA version only.
• Mode
: SSB, CW, RTTY, AM, FM, WFM
(WFM is for receive only)
• Number of memory CH: 503 (split memory: 99×5 banks; scan
edges: 6; call channel: 2 ) channels
• Antenna connector : SO-239×2 (for HF/50 MHz and
144/430 MHz) /50 Ω
• Usable temperature : –10°C to +60°C (+14°F to +140°F)
range
• Frequency stability : Less than ± 0.5 ppm
(0°C to + 50°C; + 32°F to +122°F)
• Power supply
: 13.8 V DC±15% (negative ground)
requirement
• Current drain
: Transmit (at 100 W) 22 A
Receive squelched 1.3 A
(at 13.8 V DC)
max. audio 1.6 A
• Dimensions
: 167(W) × 58(H) × 180(D) mm,
(projections not included) 69⁄16(W) × 29⁄32(H) × 73⁄32(D) in
• Weight (approx.)
: 2.3 kg (5 lb 1 oz)
• CI-V connector
: 2-conductor 3.5 (d) mm (1⁄8˝)
• Video connector
: 2-conductor 3.5 (d) mm (1⁄8˝)
• ACC connector
: 13-pin
• Data connector
: 6-pin
■ Transmitter
• Output power
:
SSB, CW, FM, RTTY 2–100 W (1.8–50 MHz bands)
2–50 W (144 MHz band)
2–35 W (430 MHz band)
AM
1–40 W (1.8–50 MHz bands)
2–20 W (144 MHz band)
2–14 W (430 MHz band)
• Modulation system :
SSB
Balanced modulation
AM
Low level modulation
FM
Variable reactance modulation
• Spurious emissions : Less than –60 dB*
*spurious freq.: below 30 MHz –50 dB, above 50 MHz –60 dB
• Carrier suppression
• Unwanted sideband
• Microphone
connector
• KEY connector
• RTTY connector
: More than 50 dB
: More than 50 dB
: 8-pin modular jack (600 Ω)
18
■ Receiver
• Receive system
:
SSB/CW/RTTY/AM/FM Triple-conversion superheterodyne
WFM Double-conversion superheterodyne
• Intermediate frequencies:
1st
SSB/CW/RTTY/AM/FM 124.487 MHz
WFM
134.732 MHz
2nd
SSB/CW/RTTY/AM/FM 455 kHz
WFM
10.700 MHz
3rd
SSB/CW/RTTY/AM/FM 16.15 kHz
• Sensitivity (at preamp ON):
Frequency SSB/CW/
RTTY
range
10 dB S/N
[MHz]
0.5–1.8
AM
10 dB S/N
FM
WFM
12 dB SINAD 12 dB SINAD
—
13 µV
0.15 µV
2.0 µV
50 MHz band 0.12 µV
1.0 µV
0.25 µV
—
—
—
10.0 µV
1.0 µV
0.18 µV
—
1.8–28
28–29.995
76–108
—
144/430 MHz
0.11 µV
bands
—
—
—
—
0.5 µV
—
• Squelch sensitivity (threshold; preamp ON) :
SSB
Less than 5.6 µV
FM
Less than 0.3 µV
• Selectivity
:
SSB* (BW=2.4 kHz)
More than 2.4 kHz/–6 dB
Less than 3.6 kHz/–60 dB
CW* (BW=500 Hz)
More than 500 Hz/–6 dB
Less than 900 Hz/–60 dB
RTTY (BW=350 Hz)
More than 360 Hz/–6 dB
Less than 650 Hz/–60 dB
AM (BW=6 kHz)
More than 6.0 kHz/–6 dB
Less than 15.0 kHz/–60 dB
FM (BW=15 kHz)
More than 12.0 kHz/–6 dB
Less than 20.0 kHz/–60 dB
*IF filter shape is set to SHARP.
• Spurious and image rejection ratio:
HF bands
More than 70 dB
50 MHz band
More than 70 dB (except IF/2 through)
144/430 MHz band More than 65 dB (except IF through)
• Audio output power : More than 2.0 W at 10% distortion
with an 8 Ω load (at 13.8 V DC)
• RIT variable range : ±9.99 kHz
• PHONES connector : 3-conductor 3.5 (d) mm (1⁄8˝)/8 Ω
• EXT SP connector : 2-conductor 3.5 (d) mm (1⁄8˝)/8 Ω
17
18
: 3-conductor 6.35 (d) mm (1⁄4˝)
: 3-conductor 3.5 (d) mm (1⁄8˝)
148
19
OPTIONS
AT-180 HF/50 MHz AUTOMATIC
ANTENNA TUNER
AH-4 HF AUTOMATIC ANTENNA
AH-2b ANTENNA ELEMENT
TUNER
Fully automatic antenna tuner with preset
memories for each 100 kHz. Unique “automatic tuner on” function is available. See
p. 141 for AT-180 specifications.
Specially designed to tune a long wire antenna for portable or mobile HF/50 MHz operation. The “PTT tune” function provides
simple operation.
• Input power rating: 150 W
HM-151 HAND MICROPHONE
SM-20 DESKTOP MICROPHONE
A 2.5 m long antenna element for mobile operation
with the AH-4.
• Frequency coverage
7–54 MHz band with the
AH-4
CT-17 CI-V LEVEL CONVERTER
UNIT
Standard hand microphone.
Includes [UP]/[DOWN] switches and a low
cut function. The OPC-589 is necessary to
use this microphone.
For remote transceiver control using a personal computer equipped with an RS-232C
port. You can change frequencies, operating mode, memory channels, etc., via your
computer.
SP-7 EXTERNAL SPEAKER
SP-10 EXTERNAL SPEAKER
MB-62
MOBILE MOUNTING BRACKET
Compact speaker for base station operation. Height can be adjusted for your convenience.
• Input impedance: 8 Ω
• Max. input power: 5 W
External speakers suitable for mobile operation.
SP-12: Slim-type; 8 Ω/5 W
SP-10: Compact-type; 4 Ω/5 W
MB-105 MOUNTING BRACKET
MB-65 MOUNTING BASE
MB-106 CARRYING HANDLE
Allows you to conveniently vehicle-mount
the front panel of the IC-7000. An MB-105
must be used in combination with the MB65.
Convenient when carrying the transceiver.
Metal plate for attaching the front panel to a
wall or other such flat surface.
149
Mounts the transceiver main body, with or
without the front panel, inside a vehicle.
OPTIONS
19
OPC-1443
OPC-1444
OPC-589
SEPARATION CABLE
SEPARATION CABLE
MICROPHONE ADAPTOR CABLE
Provide front panel detached operation for
mobile installations or compact transceiver
operation.
• OPC-1443: 3.5 m (11.5 ft)
• OPC-1444: 5 m (16.4 ft)
Provide front panel detached operation for
mobile installations or compact transceiver
operation.
• OPC-1443: 3.5 m (11.5 ft)
• OPC-1444: 5 m (16.4 ft)
Conversion between 8-pin modular and 8pin metal connector for using a desktop microphone with the IC-7000.
OPC-598 ACC 13-PIN CABLE
OPC-599 ADAPTOR CABLE
OPC-742 ACC 13-PIN CABLE
Required when using both the AT-180
and 2 m linear amplifier.
Required when using the AT-180.
• 7 m (22 ft)
13-pin, ACC connector to 7-pin + 8-pin ACC
connector.
IC-PW1/EURO HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER
Full-duty 1 kW linear amplifier including an automatic antenna tuner. Has automatic tuning
and band selection capability. Full break-in (QSK) operation is possible. The amplifier/power
supply unit and the remote control unit are separated. An optional OPC-599 is required for
connection.
19
150
20
MENU GUIDE
Sub menu group
Main menu group
M-1 SPL A/B FIL XFC
S-1
VO
MET VSC
(SSB/AM)
M-2 MEM MW MCL V/M
VO KEY MET VSC
(CW)
M-3
VOX COM AGC TBW (SSB)
VO DEC MET VSC(RTTY)
BRK 1/4 AGC
(CW)
VO DTM MET VSC
1/4 AGC
(RTTY)
AGC
(AM)
(FM/WFM)
VOX
S-2 SCN PRI V/M VSC
SEL
VOX DUP TON 9600
S-3 MW MPW MPR
(FM/WFM)
BAND
scope
Multi function
meter
G-1
BAND scope
G-2
Multi function meter
G-3
SWR meter
Graphic menu group
Push
[AF]
momentarily
Push
momentarily
Push
for 1 sec.
151
(in memory mode)
Set mode menu
Push
[Z(MENU/GRP)]
to exit
MENU GUIDE
20
Set mode description
• Set mode menu
• Miscellaneous (others) set mode
Push [Z(MENU/GRP)] or [AF] switch
to return to upper menu
• Display set mode
• Time set mode
Quick set mode
CW
mode
RTTY
mode
AM/FM
mode
No.
SSB
mode
1
RF Power
RF Power
RF Power
RF Power
2
MIC Gain
Key Speed
Twin Peak
Filter
MIC Gain
3
SSB TBW
(WIDE) L
CW Pitch
RTTY Mark
Frequency
4
SSB TBW
(WIDE) H
Side Tone
Level
RTTY Shift
Width
5
SSB TBW
(MID) L
Side Tone
Level Limit
RTTY Keying
Polarity
6
SSB TBW
(MID) H
7
SSB TBW
(NAR) L
8
SSB TBW
(NAR) H
20
152
MEMO
153
MEMO
21
154
MEMO
155
MEMO
156
A-6478H-1EX
Printed in Japan
© 2005 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan