Daikin | FXFQ48PVJU | Specifications | Daikin FXFQ48PVJU Specifications

Daikin FXFQ48PVJU Specifications
EDUS391000 - F1
FXFQ-P
Ceiling Mounted Cassette Type
(Round Flow)
AMERICAS
EDUS391000-F1
FXFQ-P
Ceiling Mounted Cassette Type
(Round Flow)
1.Specifications ...................................................................... 2
2.Dimensions.......................................................................... 4
3.Piping Diagrams .................................................................. 7
4.Wiring Diagrams .................................................................. 8
5.Electric Characteristics ........................................................ 9
6.Capacity Tables................................................................. 10
6.1 Cooling Capacity ..................................................................10
6.2 Heating Capacity ..................................................................11
7.Sound Levels (Reference)................................................. 12
7.1 Overall ..................................................................................12
7.2 Octave Band Level ...............................................................12
8.Center of Gravity ............................................................... 14
9.Installation ......................................................................... 15
10.Accessories ..................................................................... 41
FXFQ-P
1
Specifications
EDUS391000-F1
1. Specifications
Ceiling Mounted Cassette Type (Round Flow)
Model
FXFQ09PVJU
FXFQ12PVJU
FXFQ18PVJU
FXFQ24PVJU
1, 3 Cooling Capacity
Btu/h
9,500
12,000
18,000
24,000
2, 3 Heating Capacity
Btu/h
10,500
13,500
20,000
27,000
Galvanized Steel Plate
Galvanized Steel Plate
Galvanized Steel Plate
Galvanized Steel Plate
in. (mm)
9-11/16 × 33-1/16 × 33-1/16
(246 x 840 x 840)
9-11/16 × 33-1/16 × 33-1/16
(246 x 840 x 840)
9-11/16 × 33-1/16 × 33-1/16
(246 x 840 x 840)
9-11/16 × 33-1/16 × 33-1/16
(246 x 840 x 840)
2×6×21
2×6×21
2×6×21
2×10×21
ft² (m²)
2.87 (0.9)
2.87 (0.9)
2.87 (0.9)
4.80 (1.46)
Model
QTS48C15M
QTS48C15M
QTS48C15M
QTS48C15M
Type
Turbo Fan
Turbo Fan
Turbo Fan
Turbo Fan
W
56
56
56
56
cfm
460/390/350
460/390/350
560/470/390
780/620/470
Casing / Color
Dimensions: (H×W×D)
Coil (Cross
Fin Coil)
Fan
Rows×Stages×FPI
Face Area
Motor Output
Air Flow Rate (HH/H/L)
Drive
Temperature Control
Sound Absorbing Thermal Insulation Material
Direct Drive
Direct Drive
Microprocessor Thermostat
for Cooling and Heating
Microprocessor Thermostat
for Cooling and Heating
Polyurethane Form
Polyurethane Form
Polyurethane Form
Polyurethane Form
43 (19.5)
43 (19.5)
43 (19.5)
48.5 (22)
dBA
30/28/27
30/28/27
32/30/27
36/32/28
Liquid Pipes
in. (mm)
φ1/4 (6.4) (Flare Connection)
φ1/4 (6.4) (Flare Connection)
φ1/4 (6.4) (Flare
Connection)
φ3/8 (9.5) (Flare Connection)
Gas Pipes
in. (mm)
φ1/2 (12.7) (Flare
Connection)
φ1/2 (12.7) (Flare
Connection)
φ1/2 (12.7) (Flare
Connection)
φ5/8 (15.8) (Flare
Connection)
VP25
VP25
VP25
VP25
Drain Pipe
in. (mm)
5 Sound Level (HH/H/L)
Safety Devices
Dia. 1-1/4(31.8)
Dia. 1-1/4(31.8)
Dia. 1-1/4(31.8
Dia. 1-1/4(31.8
( External
( External
( External
( External
Internal Dia. 1(25.4) )
Internal Dia. 1(25.4) )
Internal Dia. 1(25.4) )
Internal Dia. 1(25.4) )
Fuse
Fuse
Fuse
Fuse
Electronic Expansion Valve
Electronic Expansion Valve
Electronic Expansion Valve
Electronic Expansion Valve
R-410A VRV Series
R-410A VRV Series
R-410A VRV Series
R-410A VRV Series
Operation Manual.
Installation Manual. Paper
Pattern for Installation. Drain
Hose. Sealing Pads. Clamps.
Washers. Screws. Insulation
for Fitting. Clamp Metal.
Operation Manual.
Installation Manual. Paper
Pattern for Installation. Drain
Hose. Sealing Pads. Clamps.
Washers. Screws. Insulation
for Fitting. Clamp Metal.
Operation Manual.
Installation Manual. Paper
Pattern for Installation.
Drain Hose. Sealing Pads.
Clamps. Washers. Screws.
Insulation for Fitting. Clamp
Metal.
Operation Manual.
Installation Manual. Paper
Pattern for Installation. Drain
Hose. Sealing Pads.
Clamps. Washers. Screws.
Insulation for Fitting. Clamp
Metal.
Model
BYCP125K-W1
BYCP125K-W1
BYCP125K-W1
BYCP125K-W1
Color
Fresh White
Fresh White
Fresh White
Fresh White
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
Resin Net
(with Mold Resistant)
Resin Net
(with Mold Resistant)
Resin Net
(with Mold Resistant)
Resin Net
(with Mold Resistant)
12.2 (5.5)
12.2 (5.5)
12.2 (5.5)
12.2 (5.5)
Refrigerant Control
Connectable outdoor unit
Standard Accessories
Decoration
Panels
(Option)
Direct Drive
Microprocessor Thermostat
for Cooling and Heating
Lbs (kg)
Weight
Piping
Connections
Direct Drive
Microprocessor Thermostat
for Cooling and Heating
Dimensions: (H×W×D)
in. (mm)
Air Filter
Weight
Lbs (kg)
Drawing No.
C: 3D070521
Notes:
 1 Nominal cooling capacities are based on the following conditions:
 2
 3
4
 5
2
Return air temperature: 80°FDB (27°CDB), 67°FWB (19.4°CWB)
Outdoor temperature: 95°FDB (35°CFB)
Equivalent ref. piping length: 25ft (7.5 m) (Horizontal)
Nominal heating capacities are based on the following conditions:
Return air temperature: 70°FDB(21°CDB).
Outdoor temperature: 47°FDB, 43°FWB (8.3°CDB, 6°CWB)
Equivalent ref. piping length: 25ft (7.5 m) (Horizontal)
Capacities are net, including a deduction for cooling (an addition for heating) for indoor fan motor heat.
Refer to page 9 for Power Input.
Sound levels are measured under JIS conditions.
FXFQ-P
EDUS391000-F1
Specifications
Ceiling Mounted Cassette Type (Round Flow)
Model
FXFQ30PVJU
FXFQ36PVJU
FXFQ48PVJU
1, 3 Cooling Capacity
Btu/h
30,000
36,000
48,000
2, 3 Heating Capacity
Btu/h
34,000
40,000
54,000
Galvanized Steel Plate
Galvanized Steel Plate
Galvanized Steel Plate
in. (mm)
9-11/16 × 33-1/16 × 33-1/16
(246 x 840 x 840)
11-5/16×33-1/16×33-1/16
(287 x 840 x 840)
11-5/16×33-1/16×33-1/16
(287 x 840 x 840)
2×10×21
2×12×21
2×12×21
ft² (m2)
4.80 (1.46)
5.76 (1.8)
5.76 (1.8)
Model
QTS48C15M
QTS48C15M
QTS48C15M
Type
Turbo Fan
Turbo Fan
Turbo Fan
W
56
120
120
cfm
830/670/530
1180/910/700
1220/970/790
Casing / Color
Dimensions: (H×W×D)
Coil (Cross
Fin Coil)
Fan
Rows×Stages×FPI
Face Area
Motor Output
Air Flow Rate (HH/H/L)
Drive
Temperature Control
Sound Absorbing Thermal Insulation Material
Weight
5 Sound Level (HH/H/L)
Piping
Connections
Direct Drive
Direct Drive
Microprocessor Thermostat
for Cooling and Heating
Microprocessor Thermostat
for Cooling and Heating
Polyurethane Form
Polyurethane Form
Polyurethane Form
Lbs (kg
48.5 (22)
55 (25)
55 (25)
dBA
38/35/31
44/38/32
45/40/34
Liquid Pipes
in. (mm)
φ3/8 (9.5) (Flare Connection)
φ3/8 (9.5) (Flare Connection)
φ3/8 (9.5) (Flare Connection)
Gas Pipes
in. (mm)
φ5/8 (15.8) (Flare Connection)
φ5/8 (15.8) (Flare Connection)
φ5/8 (15.8) (Flare Connection)
VP25
VP25
VP25
Drain Pipe
in. (mm)
Dia. 1-1/4 (31.8)
( External
Internal Dia. 1(25.4) )
Dia. 1-1/4 (31.8)
( External
Internal Dia. 1(25.4) )
1-1/4 (31.8)
( External
Internal Dia. 1 (25.4) )
Safety Devices
Refrigerant Control
Connectable outdoor unit
Fuse
Fuse
Fuse
Electronic Expansion Valve
Electronic Expansion Valve
Electronic Expansion Valve
R-410A VRV Series
R-410A VRV Series
R-410A VRV Series
Operation Manual. Installation Manual.
Paper Pattern for Installation. Drain
Hose. Sealing Pads. Clamps. Washers.
Screws. Insulation for Fitting. Clamp
Metal.
Operation Manual. Installation Manual.
Paper Pattern for Installation. Drain
Hose. Sealing Pads. Clamps. Washers.
Screws. Insulation for Fitting. Clamp
Metal.
Operation Manual. Installation Manual.
Paper Pattern for Installation. Drain
Hose. Sealing Pads. Clamps.
Washers. Screws. Insulation for Fitting.
Clamp Metal.
Model
BYCP125K-W1
BYCP125K-W1
BYCP125K-W1
Color
Fresh White
Fresh White
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
Resin Net
(with Mold Resistant)
Resin Net
(with Mold Resistant)
Resin Net
(with Mold Resistant)
12.2 (5.5)
12.2 (5.5)
Standard Accessories
Decoration
Panels
(Option)
Direct Drive
Microprocessor Thermostat
for Cooling and Heating
Dimensions: (H×W×D)
in. (mm)
Air Filter
Weight
Lbs (kg
12.2 (5.5)
Drawing No.
Fresh White
2 × 37-3/8 × 37-3/8
(51 x 949 x 949)
C: 3D070521
Notes:
 1 Nominal cooling capacities are based on the following conditions:
 2
 3
4
 5
Return air temperature: 80°FDB(27°CDB), 67°FWB(19.4°CWB)
Outdoor temperature: 95°FDB (35°CDB)
Equivalent ref. piping length: 25ft (7.5 m)(Horizontal)
Nominal heating capacities are based on the following conditions:
Return air temperature: 70°FDB(21°CDB).
Outdoor temperature: 47°FDB (8.3°CDB ), 43°FWB (6°CWB)
Equivalent ref. piping length: 25ft (7.5 m) (Horizontal)
Capacities are net, including a deduction for cooling (an addition for heating) for indoor fan motor heat.
Refer to page 9 for Power Input.
Sound levels are measured under JIS conditions.
FXFQ-P
3
DO NOT PLACE THE UNIT IN AREAS WITH EXCESSIVE HUMIDITY.
WHEN HUMIDITY EXCEEDS 80%, CONDENSATION CAN FORM ON THE UNIT.
3D070522
Dimensions
4
EDUS391000-F1
2. Dimensions
FXFQ09PVJU
FXFQ12PVJU
FXFQ18PVJU
Unit (in.)
FXFQ-P
DO NOT PLACE THE UNIT IN AREAS WITH EXCESSIVE HUMIDITY.
WHEN HUMIDITY EXCEEDS 80%, CONDENSATION CAN FORM ON THE UNIT.
3D070524
EDUS391000-F1
FXFQ-P
Dimensions
FXFQ24PVJU
FXFQ30PVJU
Unit (in.)
5
DO NOT PLACE THE UNIT IN AREAS WITH EXCESSIVE HUMIDITY.
WHEN HUMIDITY EXCEEDS 80%, CONDENSATION CAN FORM ON THE UNIT.
3D070523
Dimensions
6
EDUS391000-F1
FXFQ36PVJU
FXFQ48PVJU
Unit (in.)
FXFQ-P
EDUS391000-F1
Piping Diagrams
3. Piping Diagrams
FXFQ09PVJU / FXFQ12PVJU / FXFQ18PVJU / FXFQ24PVJU / FXFQ30PVJU / FXFQ36PVJU / FXFQ48PVJU
4D024460D
Model
FXFQ-P
GAS
Liquid
FXFQ09 / 12 / 18PVJU
φ1/2
φ1/4
FXFQ24 / 30 / 36 / 48PVJU
φ5/8
φ3/8
7
Wiring Diagrams
EDUS391000-F1
4. Wiring Diagrams
PROTECTIVE GROUND
NOISELESS GROUND
3D070301C
FXFQ09PVJU / FXFQ12PVJU / FXFQ18PVJU / FXFQ24PVJU / FXFQ30PVJU / FXFQ36PVJU / FXFQ48PVJU
8
FXFQ-P
EDUS391000-F1
Electric Characteristics
5. Electric Characteristics
4D070525A
FXFQ-P
9
Capacity Tables
EDUS391000-F1
6. Capacity Tables
6.1
Cooling Capacity
FXFQ-P
Indoor Unit
[Cooling Capacity]
Outdoor
Air Temp.
°FDB
09
12
18
24
30
36
48
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
61
TC
MBh
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.9
18.9
18.9
18.9
18.9
18.9
18.9
18.9
23.7
23.7
23.7
23.7
23.7
23.7
23.7
23.7
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
37.9
37.9
37.9
37.9
37.9
37.9
37.9
37.9
64
SHC
MBh
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
19.4
19.4
19.4
19.4
19.4
19.4
19.4
19.4
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
30.2
30.2
30.2
30.2
30.2
30.2
30.2
30.2
TC
MBh
8.5
8.5
8.5
8.5
8.5
8.5
8.5
8.5
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
16.1
16.1
16.1
16.1
16.1
16.1
16.1
16.1
21.5
21.5
21.5
21.5
21.5
21.5
21.5
21.5
26.8
26.8
26.8
26.8
26.8
26.8
26.8
26.8
32.2
32.2
32.2
32.2
32.2
32.2
32.2
32.2
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
SHC
MBh
8.5
8.5
8.5
8.5
8.5
8.5
8.5
8.5
9.8
9.8
9.8
9.8
9.8
9.8
9.8
9.8
13.3
13.3
13.3
13.3
13.3
13.3
13.3
13.3
18.2
18.2
18.2
18.2
18.2
18.2
18.2
18.2
21.1
21.1
21.1
21.1
21.1
21.1
21.1
21.1
26.7
26.7
26.7
26.7
26.7
26.7
26.7
26.7
33.1
33.1
33.1
33.1
33.1
33.1
33.1
33.1
Indoor Air Temp. °FWB
67
70
TC
SHC
TC
SHC
MBh
MBh
MBh
MBh
9.5
9.5
10.5
9.8
9.5
9.5
10.4
9.7
9.5
9.5
10.2
9.5
9.5
9.5
10.0
9.7
9.5
9.5
9.9
9.5
9.5
9.5
9.7
9.7
9.3
9.3
9.5
9.5
9.2
9.2
9.3
9.3
12.0
10.3
13.3
11.2
12.0
10.3
13.1
11.0
12.0
10.3
12.9
10.9
12.0
10.3
12.7
10.3
12.0
10.3
12.5
10.4
12.0
10.3
12.2
10.5
11.8
10.4
12.0
10.4
11.6
10.2
11.8
10.5
18.0
14.1
19.9
14.9
18.0
14.1
19.7
14.7
18.0
14.1
19.3
14.7
18.0
14.1
19.0
14.2
18.0
14.1
18.7
14.2
18.0
14.1
18.4
14.2
17.7
14.1
18.0
13.8
17.3
13.8
17.7
13.8
24.0
18.9
26.5
19.9
24.0
18.9
26.2
19.7
24.0
18.9
25.8
19.6
24.0
18.9
25.3
19.5
24.0
18.9
24.9
19.1
24.0
18.9
24.5
18.7
23.6
18.9
24.0
18.6
23.1
18.8
23.6
18.2
30.0
22.3
33.2
23.5
30.0
22.3
32.8
23.2
30.0
22.3
32.2
23.1
30.0
22.3
31.7
22.6
30.0
22.3
31.1
22.1
30.0
22.3
30.6
22.2
29.5
22.2
30.0
21.7
28.9
21.6
29.5
21.5
36.0
28.6
39.8
30.1
36.0
28.6
39.3
29.7
36.0
28.6
38.7
29.2
36.0
28.6
38.0
28.9
36.0
28.6
37.4
28.9
36.0
28.6
36.7
28.6
35.3
28.6
36.1
28.0
34.7
28.0
35.4
27.7
48.0
35.3
53.1
37.4
48.0
35.3
52.4
36.9
48.0
35.3
51.5
36.3
48.0
35.3
50.7
36.1
48.0
35.3
49.8
35.6
48.0
35.3
48.9
35.2
47.1
35.2
48.1
34.9
46.3
34.6
47.2
34.5
72
TC
SHC
MBh
MBh
10.7
9.6
10.5
9.5
10.3
9.6
10.2
9.5
10.0
9.6
9.8
9.1
9.6
9.0
9.5
9.1
13.5
10.4
13.3
10.3
13.0
10.4
12.8
10.5
12.6
10.3
12.4
10.4
12.2
9.9
12.0
10.0
20.2
14.1
19.9
14.1
19.6
13.8
19.2
13.8
18.9
13.5
18.6
13.5
18.3
13.5
17.9
13.5
27.0
19.1
26.5
17.0
26.1
18.6
25.7
18.6
25.2
18.2
24.8
18.1
24.4
18.3
23.9
17.9
33.7
22.4
33.2
22.1
32.6
21.6
32.1
21.7
31.5
21.2
31.0
21.3
30.4
20.8
29.9
20.9
40.4
28.8
39.8
28.5
39.1
27.9
38.5
27.9
37.8
27.6
37.2
27.2
36.5
27.2
35.9
26.9
53.9
35.9
53.0
35.5
52.2
35.0
51.3
34.6
50.4
34.3
49.6
33.8
48.7
33.4
47.8
32.9
75
TC
SHC
MBh
MBh
10.9
9.2
10.7
9.0
10.5
9.2
10.3
9.0
10.2
8.8
10.0
8.7
9.8
8.8
9.7
8.7
13.7
10.0
13.5
9.9
13.3
10.0
13.1
10.0
12.8
9.9
12.6
10.0
12.4
9.5
12.2
9.6
20.6
13.8
20.2
13.5
19.9
13.5
19.6
13.5
19.3
13.5
18.9
13.2
18.6
13.2
18.3
12.6
27.4
18.3
27.0
18.2
26.6
18.2
26.1
17.8
25.7
17.9
25.3
17.9
24.8
17.4
24.4
17.4
34.3
21.3
33.7
21.4
33.2
20.9
32.7
21.0
32.1
20.5
31.6
20.6
31.0
20.1
30.5
20.0
41.1
28.0
40.5
27.6
39.8
27.3
39.2
27.3
38.5
26.8
37.9
26.4
37.2
26.1
36.6
26.1
54.9
34.3
54.0
33.8
53.1
33.9
52.3
33.5
51.4
33.0
50.5
32.6
49.7
32.3
48.8
31.8
TC : Total capacity ; MBh
SHC : Sensible heat capacity ; MBh
10
FXFQ-P
EDUS391000-F1
6.2
Capacity Tables
Heating Capacity
FXFQ-P
Indoor Unit
[Heating Capacity]
Outdoor Air Temp.
°FDB
22.0
26.0
30.0
35.0
39.0
44.0
09
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
12
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
18
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
24
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
30
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
36
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
48
44.0
47.0
51.0
54.0
57.0
60.0
TC :Total capacity ; MBh
FXFQ-P
°FWB
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
62
TC
MBh
9.3
9.9
10.4
11.1
11.7
12.2
12.2
12.2
12.2
12.2
12.2
12.0
12.7
13.4
14.2
15.1
15.7
15.7
15.7
15.7
15.7
15.7
17.8
18.8
19.9
21.1
22.3
23.3
23.3
23.3
23.3
23.3
23.3
24.0
25.4
26.9
28.5
30.2
31.5
31.5
31.5
31.5
31.5
31.5
30.2
31.9
33.8
35.8
38.0
39.7
39.7
39.7
39.7
39.7
39.7
35.5
37.6
39.8
42.2
44.7
46.7
46.7
46.7
46.7
46.7
46.7
48.0
50.7
53.7
56.9
60.3
63.0
63.0
63.0
63.0
63.0
63.0
65
TC
MBh
9.3
9.8
10.4
11.0
11.5
11.5
11.5
11.5
11.5
11.5
11.5
12.0
12.7
13.4
14.2
14.7
14.7
14.7
14.7
14.7
14.7
14.7
17.7
18.7
19.8
21.0
21.9
21.9
21.9
21.9
21.9
21.9
21.9
23.9
25.3
26.8
28.4
29.5
29.5
29.5
29.5
29.5
29.5
29.5
30.1
31.9
33.7
35.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
35.4
37.5
39.7
42.1
43.7
43.7
43.7
43.7
43.7
43.7
43.7
47.9
50.6
53.6
56.8
59.0
59.0
59.0
59.0
59.0
59.0
59.0
Indoor Air Temp. °FDB
68
70
TC
TC
MBh
MBh
9.3
9.3
9.8
9.8
10.4
10.4
10.9
10.5
10.9
10.5
10.9
10.5
10.9
10.5
10.9
10.5
10.9
10.5
10.9
10.5
10.9
10.5
11.9
11.9
12.6
12.6
13.4
13.4
14.0
13.5
14.0
13.5
14.0
13.5
14.0
13.5
14.0
13.5
14.0
13.5
14.0
13.5
14.0
13.5
17.7
17.7
18.7
18.7
19.8
19.8
20.7
20.0
20.7
20.0
20.7
20.0
20.7
20.0
20.7
20.0
20.7
20.0
20.7
20.0
20.7
20.0
23.9
23.9
25.3
25.2
26.8
26.7
28.0
27.0
28.0
27.0
28.0
27.0
28.0
27.0
28.0
27.0
28.0
27.0
28.0
27.0
28.0
27.0
30.1
30.0
31.8
31.8
33.7
33.7
35.3
34.0
35.3
34.0
35.3
34.0
35.3
34.0
35.3
34.0
35.3
34.0
35.3
34.0
35.3
34.0
35.4
35.3
37.4
37.4
39.6
39.6
41.5
40.0
41.5
40.0
41.5
40.0
41.5
40.0
41.5
40.0
41.5
40.0
41.5
40.0
41.5
40.0
47.8
47.7
50.5
50.5
53.5
53.4
56.0
54.0
56.0
54.0
56.0
54.0
56.0
54.0
56.0
54.0
56.0
54.0
56.0
54.0
56.0
54.0
72
TC
MBh
9.3
9.8
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.1
11.9
12.6
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
17.6
18.7
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
23.8
25.2
26.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
30.0
31.7
32.7
32.7
32.7
32.7
32.7
32.7
32.7
32.7
32.7
35.3
37.3
38.5
38.5
38.5
38.5
38.5
38.5
38.5
38.5
38.5
47.7
50.4
52.0
52.0
52.0
52.0
52.0
52.0
52.0
52.0
52.0
75
TC
MBh
9.2
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
11.9
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
17.6
18.1
18.1
18.1
18.1
18.1
18.1
18.1
18.1
18.1
18.1
23.8
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
29.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
35.2
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
47.6
49.0
49.0
49.0
49.0
49.0
49.0
49.0
49.0
49.0
49.0
11
Sound Levels (Reference)
EDUS391000-F1
7. Sound Levels (Reference)
7.1
Overall
5 ft
(1.5 m)
1 ft
(0.3 m)
 Location of microphone
dBA
Model
7.2
208-230V, 60Hz
HH
H
L
FXFQ09PVJU
30
28
27
FXFQ12PVJU
30
28
27
FXFQ18PVJU
32
30
27
FXFQ24PVJU
36
32
28
FXFQ30PVJU
38
35
31
FXFQ36PVJU
44
38
32
FXFQ48PVJU
45
40
34
Notes:
1. The operating conditions are assumed to be
standard (JIS conditions). Power source 208230V, 60hz.
2. The operating values were obtained in an
anechoic chamber (conversion values).
3. Sound levels will vary depending on a range of
factors such as the construction (acoustic
absorption coefficient) of the particular room
in which the equipment is installed.
Octave Band Level
208V-230V, 60Hz
FXFQ09/12PVJU
FXFQ18PVJU
HH
HH
H
H
L
L
12
FXFQ-P
EDUS391000-F1
Sound Levels (Reference)
FXFQ24PVJU
FXFQ30PVJU
HH
HH
L
H
H
L
FXFQ36PVJU
FXFQ48PVJU
HH
HH
H
H
L
L
FXFQ-P
13
Center of Gravity
EDUS391000-F1
8. Center of Gravity
Unit (in.)
4D070529
14
FXFQ-P
EDUS391000-F1
Installation
9. Installation
VRV SYSTEM Inverter Heat Pump
Installation manual
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
SAFETY CONSIDERATIONS........................................................................................ 1
BEFORE INSTALLATION.............................................................................................. 3
SELECTING INSTALLATION SITE ............................................................................... 6
PREPARATIONS BEFORE INSTALLATION ................................................................ 7
INDOOR UNIT INSTALLATION..................................................................................... 9
REFRIGERANT PIPING WORK .................................................................................. 10
DRAIN PIPING WORK ................................................................................................ 13
ELECTRIC WIRING WORK......................................................................................... 16
WIRING EXAMPLE AND HOW TO SET THE REMOTE CONTROLLER ................... 17
INSTALLATION OF THE DECORATION PANEL...........................................................24
FIELD SETTING .......................................................................................................... 24
TEST OPERATION...................................................................................................... 26
1. SAFETY CONSIDERATIONS
Read these “SAFETY CONSIDERATIONS for Installation” carefully before installing air conditioning equipment. After completing the installation, make sure that the unit operates properly during the startup operation.
Instruct the customer on how to operate and maintain the unit. Inform customers that they should store this
Installation Manual with the Operation Manual for future reference.
Always use a licensed installer or contractor to install this product. Improper installation can result in water or
refrigerant leakage, electrical shock, fire, or explosion.
Meanings of DANGER, WARNING, CAUTION, and NOTE Symbols:
DANGER ........... Indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING ......... Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION .......... Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury. It may also be used to alert against unsafe practices.
NOTE................. Indicates situations that may result in equipment or property-damage accidents only.
DANGER
• Refrigerant gas is heavier than air and replaces oxygen. A massive leak can lead to oxygen depletion,
especially in basements, and an asphyxiation hazard could occur leading to serious injury or death.
• Do not ground units to water pipes, gas pipes, telephone wires, or lightning rods as incomplete grounding
can cause a severe shock hazard resulting in severe injury or death. Additionally, grounding to gas pipes
could cause a gas leak and potential explosion causing severe injury or death.
• If refrigerant gas leaks during installation, ventilate the area immediately. Refrigerant gas may produce toxic
gas if it comes in contact with fire. Exposure to this gas could cause severe injury or death.
• After completing the installation work, check that the refrigerant gas does not leak throughout the system.
• Do not install unit in an area where flammable materials are present due to risk of explosions that can cause
serious injury or death.
English
1
3P161684-5H
FXFQ-P
15
Installation
EDUS391000-F1
• Safely dispose all packing and transportation materials in accordance with federal/state/local laws or ordinances. Packing materials such as nails and other metal or wood parts, including plastic packing materials used for transportation may cause injuries or death by suffocation.
WARNING
• Only qualified personnel must carry out the installation work. Installation must be done in accordance with
this installation manual. Improper installation may result in water leakage, electric shock, or fire.
• When installing the unit in a small room, take measures to keep the refrigerant concentration from exceeding allowable safety limits. Excessive refrigerant leaks, in the event of an accident in a closed ambient
space, can lead to oxygen deficiency.
• Use only specified accessories and parts for installation work. Failure to use specified parts may result in
water leakage, electric shocks, fire, or the unit falling.
• Install the air conditioner on a foundation strong enough that it can withstand the weight of the unit. A foundation of insufficient strength may result in the unit falling and causing injuries.
• Take into account strong winds, typhoons, or earthquakes when installing. Improper installation may result
in the unit falling and causing accidents.
• Make sure that a separate power supply circuit is provided for this unit and that all electrical work is carried
out by qualified personnel according to local, state, and national regulations. An insufficient power supply
capacity or improper electrical construction may lead to electric shocks or fire.
• Make sure that all wiring is secured, that specified wires are used, and that no external forces act on the terminal connections or wires. Improper connections or installation may result in fire.
• When wiring, position the wires so that the control box lid can be securely fastened. Improper positioning of
the control box lid may result in electric shocks, fire, or the terminals overheating.
• Before touching electrical parts, turn off the unit.
• Be sure to install a ground fault circuit interrupter if one is not already available. This helps prevent electrical
shocks or fire.
• Securely fasten the outside unit terminal cover (panel). If the terminal cover/panel is not installed properly,
dust or water may enter the outside unit causing fire or electric shock.
• When installing or relocating the system, keep the refrigerant circuit free from substances other than the
specified refrigerant (R410A) such as air. Any presence of air or other foreign substance in the refrigerant
circuit can cause an abnormal pressure rise or rupture, resulting in injury.
• Do not change the setting of the protection devices. If the pressure switch, thermal switch, or other protection device is shorted and operated forcibly, or parts other than those specified by Daikin are used, fire
or explosion may occur.
CAUTION
• Do not touch the switch with wet fingers. Touching a switch with wet fingers can cause electric shock.
• Do not allow children to play on or around the unit to prevent injury.
• Do not touch the refrigerant pipes during and immediately after operation as the refrigerant pipes may be
hot or cold, depending on the condition of the refrigerant flowing through the refrigerant piping, compressor,
and other refrigerant cycle parts. Your hands may suffer burns or frostbite if you touch the refrigerant pipes.
To avoid injury, give the pipes time to return to normal temperature or, if you must touch them, be sure to
wear proper gloves.
• Heat exchanger fins are sharp enough to cut.
To avoid injury wear glove or cover the fins when working around them.
• Install drain piping to proper drainage. Improper drain piping may result in water leakage and property damage.
• Insulate piping to prevent condensation.
• Be careful when transporting the product.
• Do not turn off the power immediately after stopping operation. Always wait for at least 5 minutes before
turning off the power. Otherwise, water leakage may occur.
• Do not use a charging cylinder. Using a charging cylinder may cause the refrigerant to deteriorate.
2
English
3P161684-5H
16
FXFQ-P
EDUS391000-F1
Installation
• Refrigerant R410A in the system must be kept clean, dry, and tight.
(a) Clean and Dry -- Foreign materials (including mineral oils such as SUNISO oil or moisture) should be
prevented from getting into the system.
(b) Tight -- R410A does not contain any chlorine, does not destroy the ozone layer, and does not reduce
the earth’s protection again harmful ultraviolet radiation. R410A can contribute to the greenhouse effect
if it is released. Therefore take proper measures to check for the tightness of the refrigerant piping
installation. Read the chapter Refrigerant Piping and follow the procedures.
• Since R410A is a blend, the required additional refrigerant must be charged in its liquid state. If the refrigerant is charged in a state of gas, its composition can change and the system will not work properly.
• The indoor unit is for R410A. See the catalog for indoor models that can be connected. Normal operation
is not possible when connected to other units.
• Indoor units are for indoor installation only. Outdoor units can be installed either outdoors or indoors.
• Do not install the air conditioner in the following locations:
(a) Where a mineral oil mist or oil spray or vapor is produced, for example, in a kitchen.
Plastic parts may deteriorate and fall off or result in water leakage.
(b) Where corrosive gas, such as sulfurous acid gas, is produced.
Corroding copper pipes or soldered parts may result in refrigerant leakage.
(c) Near machinery emitting electromagnetic waves.
Electromagnetic waves may disturb the operation of the control system and cause the unit to malfunction.
(d) Where flammable gas may leak, where there is carbon fiber, or ignitable dust suspension in the air, or
where volatile flammables such as thinner or gasoline are handled. Operating the unit in such conditions can cause a fire.
• Take adequate measures to prevent the outside unit from being used as a shelter by small animals. Small
animals making contact with electrical parts can cause malfunctions, smoke, or fire. Instruct the customer
to keep the area around the unit clean.
NOTE
• Install the power supply and control wires for the indoor and outdoor units at least 3.5 feet away from televisions or radios to prevent image interference or noise. Depending on the radio waves, a distance of
3.5 feet may not be sufficient to eliminate the noise.
• Dismantling the unit, treatment of the refrigerant, oil and additional parts must be done in accordance with
the relevant local, state, and national regulations.
• Do not use the following tools that are used with conventional refrigerants: gauge manifold, charge hose, gas leak
detector, reverse flow check valve, refrigerant charge base, vacuum gauge, or refrigerant recovery equipment.
• If the conventional refrigerant and refrigerator oil are mixed in R410A, the refrigerant may deteriorate.
• This air conditioner is an appliance that should not be accessible to the general public.
• The wall thickness of field-installed pipes should be selected in accordance with the relevant local, state,
and national regulations.
2. BEFORE INSTALLATION
Do not exert pressure on the resin parts when opening the unit or when moving it after opening.
Be sure to check the type of R410A refrigerant to be used before doing any work. (Using an incorrect
refrigerant will prevent normal operation of the unit.)
• When opening the unit or moving it after opening, be sure to lift it by holding on to the lifting lugs without
exerting any pressure on other parts, especially, drain piping, and other resin parts.
• Decide upon a line of transport.
• Leave the unit inside its packaging while moving, until reaching the installation site. Use a sling of soft material, where unpacking is unavoidable or protective plates together with a rope when lifting, to avoid damage
or scratches to the unit.
• Refer to the installation manual of the outdoor unit for items not described in this manual.
• Do not dispose of any parts necessary for installation until the installation is complete.
English
3
3P161684-5H
FXFQ-P
17
Installation
EDUS391000-F1
1. PRECAUTIONS
•
•
•
•
Be sure to read this manual before installing the indoor unit.
When selecting installation site, refer to the paper pattern.
This unit is suitable for installation in a household, commercial and light industrial environment.
Do not install or operate the unit in rooms mentioned below.
• Laden with mineral oil, or filled with oil vapor or spray like in kitchens. (Plastic parts may deteriorate.)
• Where corrosive gas like sulfurous gas exists. (Copper tubing and brazed spots may corrode.)
• Where volatile flammable gas like thinner or gasoline is used.
• Where machines can generate electromagnetic waves. (Control system may malfunction.)
• Where the air contains high levels of salt such as that near the ocean and where voltage fluctuates
greatly such as that in factories. Also in vehicles or vessels.
2. ACCESSORIES
Check the following accessories are included with your unit.
Name
(1) Drain hose
(2) Metal clamp
Quantity
1 pc.
1 pc.
(3) Washer for
hanger bracket
8 pcs.
(4) Clamp
6 pcs.
(5) Paper pattern
for installation
1 pc.
Also used as
packing material
Shape
Name
(6) Screw (M4)
Quantity
4 pcs.
(7) Washer
fixing plate
4 pcs.
Insulation for
fitting
1 each
Sealing pad
1 each
1 pc.
1 pc.
(10) Large
For paper
pattern for
installation
(8) for gas
pipe
(13) Small
(11) Medium-1
(14)
Shape
(9) for liquid
pipe
(12) Medium-2
Name
Installation guide
Insulation tube
Quantity
1 pc.
1 pc.
Conduit mounting
plate
1 each
(17)
(15)
Shape
4
(16)
(Other)
• Installation manual
• Operation manual
(18)
English
3P161684-5H
18
FXFQ-P
EDUS391000-F1
Installation
3. OPTIONAL ACCESSORIES
• The optional decoration panel and remote controller are required for this indoor unit. (Refer to Table 1, 2)
(However, the remote controller is not required for the slave unit of a simultaneous operation system.)
Table 1
Unit model
Optional decoration panel
BYCP125K-W1
Color : Fresh white
FXFQ09 · 12 · 18 · 24 · 30 · 36 · 48PVJU
• These are two types of remote controllers: wired and wireless. Select a remote controller from Table 2
according to customer request and install in an appropriate place.
Table 2
Remote controller
BRC1E71
BRC7F812
Wired type
Wireless type
NOTE
• If you wish to use a remote controller that is not listed in “Table 2” on page 5, select a suitable remote controller after consulting catalogs and technical materials.
FOR THE FOLLOWING ITEMS, TAKE SPECIAL CARE DURING CONSTRUCTION AND
CHECK AFTER INSTALLATION IS FINISHED.
1. Items to be checked after completion of work
Items to be checked
Are the indoor unit and outdoor unit fixed firmly?
Is the outdoor unit fully installed?
Is the gas leak test finished?
Is the unit fully insulated?
Does drainage flow smoothly?
Does the power supply voltage correspond
to that shown on the name plate?
Are wiring and piping correct?
Is the unit safely grounded?
Is wiring size according to specifications?
Is something blocking the air outlet or inlet
of either the indoor or outdoor units?
Are refrigerant piping length and additional
refrigerant charge noted down?
If not properly done, what is likely to occur
The unit may drop, vibrate or make noise.
The unit may malfunction or the components burn out.
It may result in insufficient cooling.
Condensate water may drip.
Condensate water may drip.
The unit may malfunction or the components burn out.
The unit may malfunction or the components burn out.
It may result in electric shock.
The unit may malfunction or the components burn out.
Check
It may result in insufficient cooling.
The refrigerant charge in the system is not
clear.
2. Items to be checked at time of delivery
* Also review the “1. SAFETY CONSIDERATIONS”
Items to be checked
Check
Are the control box lid, air filter, suction grille attached?
Did you explain about operations while showing the operation manual to your customer?
Did you hand the operation manual over to your customer?
English
5
3P161684-5H
FXFQ-P
19
Installation
EDUS391000-F1
Points for explanation about operations
The items with
WARNING and
CAUTION marks in the operation manual are the items pertaining to possibilities for bodily injury and material damage in addition to the general usage of
the product. Accordingly, it is necessary that you make a full explanation about the described contents and also ask your customers to read the operation manual.
4. NOTE TO THE INSTALLER
Be sure to instruct customers how to properly operate the unit (especially cleaning filters, operating different functions, and adjusting the temperature) by having them carry out operations themselves while looking at the manual.
3. SELECTING INSTALLATION SITE
〈Hold the unit by the 4 lifting lugs when opening the box and moving it, and do not exert pressure on to any
other part piping (refrigerant, drain, etc.) or plastic parts.
If the temperature or humidity inside the ceiling might rise above 86°F or RH 80%, respectively,
addING extra insulation to the main unit bodyMAYBEREQUIRED
Use glass wool or polyethylene foam as insulation and make sure it is at least 3/8in. thick and fits inside the ceiling opening.〉
The direction this product blows can be selected. However, a separately sold shut-off material kit is
needed in order to make the unit blow in two, three, or four (corner shut-off) directions.
(1) Select an installation location with the customer’s approval which matches the following conditions.
• A location from which cool (warm) air will reach the whole room.
• A location with no objects blocking the air passage.
• A location where drainage can be done with no problem.
• A location strong enough to support the weight of the indoor unit.
• Locations where the wall is not significantly tilted.
• A location which leaves enough room for installation and service work.
• A location where there is no risk of flammable gas leaking.
• A location where the length of the indoor-outdoor piping is no longer than the tolerated length (see the
installation manual that came with the outdoor unit for details).
[Space required for installation]
(Unit: in.)
*≥60
H
*≥60
Air
discharge
At least 70in.
from the floor.
Air Air
inlet discharge
≥60
≥60
*≥60
Floor surface
Fig. 1
Model
FXFQ09 · 12 · 18 · 24 · 30PVJU
FXFQ36 · 48PVJU
6
*≥60
Fig. 2
H (in.)
10
11-3/4
English
3P161684-5H
20
FXFQ-P
EDUS391000-F1
Installation
CAUTION
• The indoor and outdoor units and the power supply wiring and remote controller cord must be installed
at least 40in. away from any televisions or radios. This is to prevent interference with picture and sound
reception. (Interference may occur even at 40in. away depending on the reception quality.)
• If installing the wireless kit, the distance of the signal sent from the remote controller might be shorter if
there are fluorescent lights which are electrically started (such as with inverters, rapid starters, etc.) in
the room. The indoor unit should be installed as far away from fluorescent lights as possible.
(2) Ceiling height
This product can be installed in ceilings up to 11-1/2ft. high (13-3/4ft. high for the 36 and 48).
If the ceiling height is 8-3/4ft. (10-1/2ft. for the 36 and 48) or more, field settings will have to be made with
the remote controller. See “11. FIELD SETTING” for details.
(3) Air direction
The air direction shown in Fig. 3 is an example.
Select the appropriate number of directions according to the shape of the room and the location of the unit.
(Field settings have to be made using the remote controller and the outlet vents have to be shut off if two,
three, or four (corner shut-off) directions are selected. See the shut-off materials (sold separately) installation manual for details.)
(4) Use suspension bolts for installation. Check if the location for the installation is strong enough to support
the weight of the unit, reinforce it if necessary, and install using suspension bolts. (The spacing of the
installation is shown on the “paper pattern for installation (5)”.)
All-round air
Pipes
Pipes
Pipes
Pipes
[Air direction]
Four air direction Three air direction Two air direction
Fig. 3
4. PREPARATIONS BEFORE INSTALLATION
Refrigerant
piping
Suspension
bolt (×4)
28(Suspension bolt pitch)
33-1/16 (Indoor unit)
33-7/8 – 35-7/8 (Ceiling opening)
37-3/8 (Decoration panel)
(Unit: in.)
Hanger
bracket
False
ceiling
View as seen from A
Fig. 5
4-15/16 – 5-1/8
33-7/8 – 35-7/8 (Ceiling opening)
33-1/16 (Indoor unit)
30-3/4 (Suspension bolt pitch)
37-3/8 (Decoration panel)
(1) Relation of ceiling opening to unit and suspension bolt position.
A
Fig. 4
English
7
3P161684-5H
FXFQ-P
21
Installation
EDUS391000-F1
35-7/8
(Dimension inside frame)
33-1/16
䡵 Installation is possible when ceiling opening dimensions is as follows
• When installing the unit within the frame for fixing false ceiling.
Frame
False
ceiling
≥13/16
33-1/16
35-7/8
(Dimension inside frame)
33-7/8
(Opening dimension inside
the flame for ceiling)
(Unit: in.)
≥13/16
33-7/8 – *35-7/8
(Ceiling opening dimension) (Ceiling-panel
overlapping dimension)
Fig. 7
Fig. 6
NOTE
• Installation is possible with a ceiling dimension of 35-7/8in. (marked with *). However, to achieve a ceilingpanel overlapping dimension of 13/16in., the spacing between the ceiling and the unit should be 1-3/8in. or
less.
(Unit: in.)
Ceiling material
≥ 1-3/8
≥ 1-3/8
Fig. 8
(2) Make the ceiling opening needed for installation where applicable. (For existing ceilings)
• Refer to the paper pattern for installation (5) for ceiling opening dimensions.
• Create the ceiling opening required for installation. From the side of the opening to the casing outlet,
implement the refrigerant and drain piping and wiring for remote controller (unnecessary for wireless
type) and indoor-outdoor unit casing outlet. Refer to “6. REFRIGERANT PIPING WORK”, “7. DRAIN
PIPING WORK” and “8. ELECTRIC WIRING WORK”.
• After making an opening in the ceiling, it may be necessary to reinforce ceiling beams to keep the ceiling
level and to prevent it from vibrating. Consult the builder for details.
<installation example>
2-4
(3) Install the suspension bolts.
(Use either a M8~M10 size bolt or the equivalent)
Use a hole-in anchor for existing ceilings, and a
sunken insert, sunken anchor or other field supplied parts for new ceilings to reinforce the ceiling
to bear the weight of the unit. Adjust clearance
(2-4in.) from the ceiling before proceeding
further.
(Unit: in.)
Ceiling slab
Anchor
Long nut or turn-buckle
Suspension bolt
False ceiling
Fig. 9
NOTE
• All the above parts are field supplied.
8
English
3P161684-5H
22
FXFQ-P
EDUS391000-F1
Installation
5. INDOOR UNIT INSTALLATION
Installing optional accessories (except for the decoration panel) before installing the indoor unit is
easier. However, for existing ceilings, install fresh air inlet component kit and branch duct before
installing the unit.
As for the parts to be used for installation work, be sure to use the provided accessories and specified parts
designated by our company.
(1) For new ceilings
(1-1)Install the indoor unit temporarily.
• Attach the hanger bracket to the suspension bolt. Be sure to fix it securely by using a nut and
washer (3) from the upper and lower sides of the hanger bracket.
The washer fixing plate (7) will prevent the washer from falling.
Field supply
Washer (3) (accessory)
Insert
Hanger bracket
Washer fixing plate (7)
(accessory)
Tighten
(double nuts)
[Securing the hanger bracket]
[Securing the washer]
Fig. 10
Fig. 11
(1-2)Refer to the paper pattern for installation (5) for ceiling opening dimension.
Consult the builder or carpenter for details.
• The center of the ceiling opening is indicated on the paper pattern for installation.
The center of the unit is indicated on the triangular mark to the unit bottom and on the paper pattern for
installation.
• Fix the paper pattern to the unit with screws (6) (×4).
• Ceiling height is shown on the side of the paper pattern for installation (5). Adjust the height of the unit
according to this indication.
Please perform one of the following, as the shape of the paper pattern for installation differs according to the model.
Center of
ceiling opening
Center of main unit
Center mark of
main unit
Paper pattern for
installation (5)
Screw (6)
(accessory)
Screw (6)
(accessory)
Fig. 12
[Installation of paper pattern for installation]
English
9
3P161684-5H
FXFQ-P
23
Installation
EDUS391000-F1
<Ceiling work>
(1-3)Adjust the unit to the right position for installation.
(Refer to “4. PREPARATIONS BEFORE INSTALLATION-(1)”.)
• Using the Installation guide (15) allows you to check the positions from the underside of the unit to the
lower ceiling surface.
Apply the short
side of the
cut-out section.
Lower ceiling
surface
Underside of
the unit
Installation guide (15)
(accessory)
(1-4)Check the unit is horizontally level.
• The indoor unit is equipped with a built-in drain pump and float
switch. Verify that it is level by using a level or a water-filled
vinyl tube.
CAUTION
If the unit is tilted against condensate flow, the float switch may
malfunction and cause water to drip.
(1-5)Remove the washer fixing plate (7) used for preventing the
washer from falling and tighten the upper nut.
(1-6)Remove the paper pattern for installation (5).
Level
Vinyl tube
[Maintaining horizontality]
Fig. 13
(2) For existing ceilings
(2-1)Install the indoor unit temporarily.
Perform step (1-1) in (1) For new ceilings.
(2-2)Adjust the height and position of the unit.
(Refer to “4. PREPARATIONS BEFORE INSTALLATION-(1)” and (1-3) in (1) For new ceilings.)
(2-3)Perform steps (1-4), (1-5) in (1) For new ceilings.
6. REFRIGERANT PIPING WORK
〈For refrigerant piping of outdoor units, see the installation manual attached to the outdoor unit.〉
〈Execute heat insulation work completely on both sides of the gas piping and the liquid piping. Otherwise, a
water leakage can result sometimes.〉
"eSURETOUSEINSULATIONTHATISDESIGNEDFORUSEWITH(6!#3YSTEMS
〈Also, in cases where the temperature and humidity of the refrigerant piping sections might exceed 86°F or
RH80%, reinforce the refrigerant insulation. (13/16in. or thicker) Condensate may form on the surface of the
insulating material.〉
〈Be sure to check the type of R410A refrigerant to be used before doing any work. (Using an incorrect refrigerant will prevent normal operation of the unit.)〉
10
English
3P161684-5H
24
FXFQ-P
EDUS391000-F1
Installation
CAUTION
• Use a pipe cutter and flare suitable for the type of refrigerant.
• Apply ester oil or ether oil around the flare section before connecting.
• To prevent dust, moisture or other foreign matter from infiltrating the tube, either pinch the end or cover
it with tape.
• Do not allow anything other than the designated refrigerant to get mixed into the refrigerant circuit, such
as air, etc. If any refrigerant gas leaks while working on the unit, ventilate the room thoroughly right away.
• Do not mix air or other gas with the specified refrigerant in the refrigeration cycle.
• Ventilate the room if refrigerant gas leaks during the work.
• The outdoor unit is charged with refrigerant.
• Be sure to use both a spanner and torque wrench together, as shown in the
drawing, when connecting or disconnecting pipes to/from the unit.
(Refer to Fig. 14)
• Refer to “Table 3” for the dimensions of flare nut spaces.
Torque wrench
Spanner
Pipe union
Flare nut
Fig. 14
• When connecting the flare nut, apply ester oil or ether oil to the flare
section (outside only), and spin 3-4 times before screwing in.
(Refer to Fig. 15)
• Keep all the screw mounting resin parts (e.g., piping presser
plates) away from oil.
If oil adheres, the strength of the screw mounting resin parts may
drop.
Coat here with ester or ether oil.
Fig. 15
CAUTION
Over-tightening the flare nut may break it and/or cause the
refrigerant to leak.
NOTE
• Use the flare nut included with the unit main body.
Table 3
Tightening torque
Flare dimensions A (in.)
φ 1/4
10.4 – 12.7lbf·ft.
0.342 – 0.358
φ 3/8
24.1 – 29.4lbf·ft.
0.504 – 0.520
φ 1/2
36.5 – 44.5lbf·ft.
0.638 – 0.654
φ 5/8
45.6 – 55.6lbf·ft.
0.760 – 0.776
Flare shape
0
R0.016-0.031
A
0
0
90 ±2
45 ±2
0
Pipe size
• Refer to “Table 3” to determine the proper tightening torque.
English
11
3P161684-5H
FXFQ-P
25
Installation
EDUS391000-F1
Not recommendED but in case of emergency
You must use a torque wrench but if you are obliged to install the unit without a torque wrench, you may
follow the installation method mentioned below.
When you keep on tightening the flare nut with a spanner, there is a point where the tightening torque
suddenly increases. From that position, further tighten the flare nut the angle shown below:
Pipe size
φ 1/4
φ 3/8
φ 1/2
φ 5/8
Further tightening angle
60 to 90 degrees
60 to 90 degrees
30 to 60 degrees
30 to 60 degrees
Recommended arm length of tool
Approx. 6in.
Approx. 8in.
Approx. 10in.
Approx. 12in.
After the work is finished, make sure to check that there is no gas leak.
• Make absolutely sure to execute heat insulation works on the pipe-connecting section after checking gas
leakage by thoroughly studying the following figure and using the attached heat insulating materials for
fitting (8) and (9). (Fasten both ends with the clamps (4).) (Refer to Fig. 16)
• Wrap the sealing pad (11) only around the insulation for the joints on the gas piping side. (Refer to Fig. 16)
Gas Piping Insulation Procedure
Insulation for fitting (8)
(accessory)
Flare nut connection
Piping insulation
material (main unit)
Wrap over from the
base of the unit to
the top of the flare
nut connection.
Attach to base
Turn seams up
Main unit
Piping insulation
material
(Field supply)
Clamp (4) (accessory)
Tighten the part other
than the piping insulation
material.
Sealing pad
medium-1 (11)
(accessory)
Liquid Piping Insulation Procedure
Insulation for fitting (9)
(accessory)
Flare nut connection
Turn seams up
Piping insulation
material (main unit)
Wrap the
insulator around
the part from the
root.
Attach to base
Liquid piping
Main unit
Piping insulation
material
(Field supply)
Clamp (4) (accessory)
Tighten the part other
than the piping insulation
material.
Gas piping
Sealing pad
medium-2 (12)
(accessory)
Screw mounting part
of piping presser plate
(2 locations)
Fig. 16
CAUTION
For field insulation, be sure to insulate field piping all the way into the pipe connections inside the machine.
Exposed piping may cause condensation or burns on contact.
12
English
3P161684-5H
26
FXFQ-P
EDUS391000-F1
Installation
CAUTION
CAUTION TO BE TAKEN WHEN BRAZING REFRIGERANT PIPING
“Do not use flux when brazing refrigerant piping. Therefore, use the phosphor copper brazing filler metal
(BCuP-2/B-Cu93P-710/795) which does not require flux.”
(Flux has extremely harmful influence on refrigerant piping systems. For instance, if the chlorine based flux is
used, it will cause pipe corrosion or, in particular, if the flux contains fluorine, it will damage the refrigerant oil.)
• Before brazing field refrigerant piping, nitrogen gas shall be blown through the piping to expel air from the
piping.
If youR brazing is done without nitrogen gas, a large amount of oxide film develops inside the piping,
and could cause system malfunction.
• When brazing the refrigerant piping, only begin brazingWHILENITROGENISFLOWINGINTOTHEREFRIGERANT
piping. Once this is done, connect the indoor unit with a flared ORAFLANGEDCONNECTION
• Nitrogen should be set to 2.9psi with a pressure-reducing valve if brazing while inserting nitrogen into the
piping. (Refer to Fig. 17)
Refrigerant piping
Pressure-reducing valve
Taping
Part to be
Hands valve
brazed
Nitrogen
Nitrogen
Fig. 17
7. DRAIN PIPING WORK
(1) Rig drain piping
• As for drain work, perform piping in such a manner that water can be drained properly.
• Employ a pipe with either the same diameter or with the diameter larger (excluding the rISER section) than
that of the connecting pipe (PVC pipe, nominal diameter 1in., outside diameter 1-1/4in.).
• Keep the drain pipe short and sloping downwards at a gradient of at least 1/100 to prevent air pockets from
forming.
• If the drain pipe cannot be sufficiently set on a slope, execute the drainRISIng piping.
• To keep the drain pipe from sagging, space hanger bracket every 3 to 5ft..
Hanger bracket
GOOD
3-5ft. 1/100 gradient or more
Fig. 18-1
WRONG
Fig. 18-2
CAUTION
Water pooling in the drainage piping can cause the drain to clog.
• Use the attached drain hose (1) and metal clamp (2).
• Insert the drain hose into the drain socket up to the base, and tighten the metal clamp securely within the
portion of a white tape of the hose-inserted tip. Tighten the metal clamp until the screw head is less than
5/32in. from the hose.
• Wrap the attached sealing pad (10) over the metal clamp and drain hose to insulate.
English
13
3P161684-5H
FXFQ-P
27
Installation
EDUS391000-F1
• Make sure that heat insulation work is executed on the following 2 spots to prevent any possible water leakage due to dew condensation.
• Indoor drain pipe
• Drain socket
Metal
clamp (2)
Metal
clamp (2)
(accessory)
Large sealing pad (10)
(accessory)
Drain hose (1)
Tape (White)
≥ 5/32in.
Fig. 19
Fig. 20
<PRECAUTIONS FOR DRAIN2)3%2P)0ING>
• Install the drainrisER pipes at a height of less than 26-1/2in..
The drain pump of this unit has a high delivery flow rate. Therefore, the higher the drainrISERheight is, the
lower the sound of draining will be. For this reason, a minimum drainriSing height of 12in. is recommended.
• Install the drainrIsERipes at a right angle to the indoor unit and no more than 11-3/4in. from the unit.
Level or
tilted
slightly up
To prevent air bubbles in the
drain hose part, keep it level or
slightly tilted up. Any bubbles in
the hose might cause the unit
to make noise due to backflow
when the drain pump stops.
DrainrisER pipe
Hanger bracket
≥ 33-1/2in.
Ceiling slab
≥ 11-3/4in.
3-5ft.
7in.
Drain hose (1)
(accessory)
Adjustable
(≥ 26-1/2in.)
Rising section
Drain hose (accessory) (1)
Metal clamp
(accessory) (2)
Fig. 21
0 – 26-1/2in.
NOTE
• To ensure no excessive pressure is applied to the included drain hose (1), do not bend or twist when installing. (This may cause leakage.)
• If converging multiple drain pipes, install according to the procedure shown below.
Central drain pipe
The drain pipe should have a downward
slope of at least 1/100 to prevent
air pockets from forming.
Fig. 22
Water accumulating in the drain
piping can cause the drain to clog.
Select converging drain pipes whose gauge is suitable for the operating capacity of the unit.
(2) After piping work is finished, check if drainage flows smoothly.
14
English
3P161684-5H
28
FXFQ-P
EDUS391000-F1
Installation
WHEN ELECTRIC WIRING WORK IS FINISHED
• Add approximately 1/4gal. of water slowly from the air outlet and check drainage flow.
• Check drainage flow during COOL running, explained under ‘‘12. TEST OPERATION’’.
• Refer to the figure on the following after checking the draining of water, and mount the thermal insulation
material for drainage (14) and thermal insulate the drain socket.
Thermal insulation
material for drainage (14)
(accessory)
Thermal insulation
material for drainage (14)
(accessory)
Sealing pad (Large) (10)
Be sure to lay the sealing
material on (14).
Make sure that there
is no clearance.
WHEN ELECTRIC WIRING WORK IS NOT FINISHED
CAUTION
• Electrical wiring work should be done by a certified electrician.
• If someone who does not have the proper qualifications performs the work, perform the following after the
test run is complete.
• Remove the control box lid. Connect the single phase power supply (SINGLE PHASE 60Hz 208/230V) to
connections L1 and L2 on the terminal block for wiring the units. Connect the ground wire firmly. When carrying out wiring work around the control box, make sure none of the connectors come undone. Be sure to
attach the control box lid before turning on the power.
• Put approximately 1/4gal. of water into the drain pan through the blow-off mouth on the left-hand side of the
drain socket. Make sure not to pour water over the drain pump or any electric parts including those of the
drain pump.
• When the power is turned on, the drain pump will operate and you can check the draining of water through
the transparent part of the drain socket. (The drain pump will stop automatically in 10 minutes.)
After checking the draining of water, mount the thermal insulation material for drainage (14) and thermal
insulate the drain socket.
• After confirming drainage (Fig. 23, Fig. 24), turn off the power and remove the power supply.
• Attach the control box lid as before.
Drain sockets
At least
4in.
(Check the
drainage now.)
Plastic watering can
(Tube should be
about 4in. long.)
Drain pump
location
Service drain outlet (with rubber plug)
(Use this outlet to drain water from
the drain pan.)
<Adding water through air discharge outlet>
[Method of adding water]
English
Fig. 23
15
3P161684-5H
FXFQ-P
29
Installation
EDUS391000-F1
Power supply
wiring terminal
block
Power supply
single phase 208/230V
Ground
L2 L1
wire
Ground
terminal
Control box lid
Fig. 24
CAUTION
Drain piping connections
Do not connect the drain piping directly to sewage pipes that smell of ammonia. The ammonia in the sewage might enter the indoor unit through the drain pipes and corrode the heat exchanger.
8. ELECTRIC WIRING WORK
8-1 General instructions
•
•
•
•
•
•
•
All field supplied parts and materials and electric works must conform to local codes.
Use copper wire only.
For electric wiring work, refer to also “WIRING DIAGRAM” attached to the unit body.
For remote controller wiring details, refer to the installation manual attached to the remote controller.
All wiring must be performed by an authorized electrician.
A circuit breaker capable of shutting down power supply to the entire system must be installed.
Refer to the installation manual attached to the outdoor unit for the size of power supply electric wire connected to the outdoor unit, the capacity of the circuit breaker and switch, and wiring instructions.
• Be sure to ground the air conditioner.
• Do not connect the ground wire to gas pipes, plumbing pipes, lightning rods, or telephone ground wires.
• Gas pipes: might cause explosions or fire if gas leaks.
• Plumbing: no grounding effect if hard vinyl piping is used.
• Telephone ground wires or lightning rods: might cause abnormally high electric potential in the ground
during lighting storms.
16
English
3P161684-5H
30
FXFQ-P
EDUS391000-F1
Installation
8-2 Electrical characteristics
Units
Model
FXFQ09PVJU
FXFQ12PVJU
FXFQ18PVJU
FXFQ24PVJU
FXFQ30PVJU
FXFQ36PVJU
FXFQ48PVJU
Hz
Volts
Voltage range
60
208/230
Max. 253
Min. 187
MCA: Min. Circuit Amps (A)
kW: Fan Motor Rated Output (kW)
Power supply
MCA
MOP
0.3
15
0.3
15
0.4
15
0.5
15
0.6
15
1.4
15
1.5
15
Fan motor
kW
FLA
0.056
0.2
0.056
0.2
0.056
0.3
0.056
0.4
0.056
0.5
0.120
1.1
0.120
1.2
MOP: Maximum Overcurrent Protective Device (A)
FLA: Full Load Amps (A)
8-3 Specifications for field supplied fuses and wire
Remote controller wiring
Transmission wiring
FUSEBREAKER3IZE
Wire3IZE
Wire size must comply withCONDUCTORSTRANDEDCOPPERCABLE
AWG18 15A
local codes.NONSHIELDED06#ORVINYLJACKET
Power supply wiring
Allowable length of transmission wirings and remote controller wiring are as follows.
(1) Outdoor unit - Indoor unit:
Max. 3280ft. (Total wiring length: 6560ft.)
(2) Indoor unit - Remote controller
Max. 1640ft.&IELDWIRINGISTOBEUSEDASAGUIDELINEONLY7IRINGSHOULDCOMPLYWITHLOCALNATIONALCODES
NOTE
1. Vinyl cord with sheath or cable (Insulated thickness : 0.04in. or more)
Field wiring diagram is to be used as a guideline only. Wiring should comply with applicable local and national codes.
9. WIRING EXAMPLE AND HOW TO SET THE REMOTE CONTROLLER
9-1 How to connect wirings
Connection of wiring between units, ground wire and for the remote controller cord (Refer to Fig. 25)
• Wiring the units and ground wire
Remove the control box lid and connect wires of matching number to the terminal block for wiring the units
(3 P) inside. And connect the ground wire to the ground terminal. In doing this, pull the wires inside through
the hole and fix the wires securely with the included clamp (4) (2 points).
• Remote controller cords (not neccessary for slave unit of simultaneous operation system)
Remove the control box lid and pull the wires inside through the hole and connect to the terminal block for
remote controller (6 P). (no polarity) Securely fix the remote controller cord with the included clamp (4) (2
points).
• After connection, attach sealing pad (13).
• Be sure to attach it to prevent the infiltration of water from the outside.
English
17
3P161684-5H
FXFQ-P
31
Installation
EDUS391000-F1
[ PRECAUTIONS ]
1. Use round crimp-style terminals for connecting wires to the power supply terminal block.
If unavailable, observe the following points when wiring.
• Do not connect wires of different gauge to the same power supply terminal.
(Looseness in the connection may cause overheating.)
• Use the specified electric wire. Connect the wire securely to the terminal. Lock the wire down without
applying excessive force to the terminal. (Tightening torque: 1lbf·ft. ±10 %)
Attach insulation sleeve
Round crimp-style terminal
Electric wire
Fig. 25
2. Tightening torque for the terminal screws.
• Use the correct screwdriver for tightening the terminal screws. If the blade of screwdriver is too small, the
head of the screw might be damaged, and the screw will not be properly tightened.
• If the terminal screws are tightened too hard, screws might be damaged.
• Refer to the table below for the tightening torque of the terminal screws.
Terminal
Terminal block for remote controller (6P)
Power supply terminal block (3P)
Size
M3.5
M4
Tightening torque
0.58 – 0.72lbf·ft
0.87 – 1.06lbf·ft
When none is available, follow the instructions below.
3. Do not connect wires of different gauge to the same grounding terminal.
Connect wires of the
same gauge to both
sideS.
Do not connect wires
of the same gauge to
one side.
Do not connect wires
of different gauges.
Fig. 26
Looseness in the connection may deteriorate protection.
4. Outside of the unit, keep transmission wiring at least 2in. away from power supply wiring. The equipment
may malfunction if subjected to electrical (external) noise.
5. For remote controller wiring, refer to the “INSTALLATION MANUAL OF REMOTE CONTROLLER.”
attached to the remote controller.
6. Never connect power supply wiring to the terminal block for remote controller. A mistake of thIS
sort could damage the entire system.
7. Use only specified wire and tightly connect wires to terminals. Be careful wires do not place external stress
on terminals. Keep wiring in neat order and so as not to obstruct other equipment such as popping open
the control box lid. Make sure the lid closes tight. Incomplete connections could result in overheating, and
in worse case, electric shock or fire.
8. Pass the power supply wire through the attached insulation tube (16) between the outlet of conduit and the
power supply terminal, and bind them together with the attached clamp (4). (Refer to Fig. 27-2)
9. Use a pair of conduit mounting plate (17) and (18) to connect a conduit to the unit as shown Fig. 27-1.
18
English
3P161684-5H
32
FXFQ-P
EDUS391000-F1
Installation
10. Use a 90° elbow type of conduit with dimensions Fig. 27-1 to prevent it from hitting the swing motor housing of decoration panel.
Conduit
<1-3/8
Conduit mounting
plate (17)
≥3/8
Conduit mounting
plate (18)
Fig. 27-1
Power supply and
ground wire
Conduit mounting
plate (17) (18)
Remote
Transmission
controller wiring wiring
Remote controller wiring
(low voltage)
P1 P2 F1 F2 T1 T2
Approximately Sheaths
1/4in.
Peel back
Forced off
3/8 – 5/8in.
the sheath
on the power 2-3/4 – 3-1/2in.
line and twist. Length of Clamp (4)
sheath to Cut off any excess
peel back material after tightening.
Power supply
terminal block
(3P)
Transmission
wiring
Insulation
tube (16)
Remote
controller
wiring
Electric insulation
Wiring
through-holes
Clamping position
Insulation
tube (16)
Secure the ground wire
power supply and with
both edges aligned.
3~4in.
(Length of sheath to peel back)
3/8~5/8in.
Power supply
and ground
wire sheath
Terminal block
for remote
controller
(P1 • P2)
Clamp (4)
Cut off any
excess material
after tightening
the power
supply wiring
and ground
Ground terminal wire together.
L2 L1
Control box lid
Wiring diagram
(Backside of control box lid)
<<Power supply and ground wire (high voltage)>>
Fig. 27-2
Observe the notes mentioned below when wiring to the terminal block for wiring the units.
English
19
3P161684-5H
FXFQ-P
33
Installation
EDUS391000-F1
CAUTION
• When clamping wiring, use the included clamping material to prevent outside pressure being exerted on the
wiring connections and clamp firmly. When doing the wiring, make sure the wiring is neat and does not
cause the control box lid to stick up, then close the cover firmly.
• When attaching the control box lid, make sure you do not pinch any wires.
• After all the wiring connections are done, fill in any gaps in the through holes with putty or insulation (procured locally) to prevent small animals and insects from entering the unit from outside. (If they get in, they
could cause short circuits in the control box.)
• Outside the unit, separate the low voltage wiring (remote controller cord) and high voltage wiring (power
supply, ground, and other power wiring) at least 2in. so that they do not pass through the same place
together. Proximity may cause electrical interference, malfunctions, and breakage.
Processing method of wiring through-holes
Wiring through-holes
Remote controller wiring
Sealing pad (Small) (13)
Putty or thermal insulation material
(procured locally)
9-2 Wiring example
• Fit the power supply wiring of each unit with a switch and fuse as shown in the drawing.
COMPLETE SYSTEM EXAMPLE (3 systems)
Power supply
Power supply wiring
Transmission wiring
Main
switch
Switch
Fuse"REAKER
BRANCHSELECTOR
unit
(Only for
Heat
recovery system)
Indoor unit
Remote controller
Fig. 28
Note:
Field wiring diagram is to be used as a guideline only. Wiring should comply with
applicable local and national codes.
20
English
3P161684-5H
34
FXFQ-P
EDUS391000-F1
Installation
1. When using 1 remote controller for 1 indoor unit. (Normal operation)
Power supply
single phase
208/230V L1 L2
60Hz
Outdoor unit
Control box
IN/D OUT/D
F1 F2 F1 F2
No. 1
System
L2 L1
Power supply Power supply Power supply
single phase single phase single phase
208/230V L1 L2 208/230V L1 L2 208/230V
L1 L2
60Hz
60Hz
60Hz
P1 P2 F1 F2 T1 T2
L2 L1
P1 P2 F1 F2 T1 T2
Indoor
unit B
Indoor
unit A
P1 P2
L2 L1
P1 P2 F1 F2 T1 T2
Indoor
unit C
P1 P 2
P1 P2
Fig. 29
L2 L1
P1 P2 F1 F2 T1 T2
Most
downstream
indoor unit
P1 P2
2. For group control or use with 2 remote controllers
Note: It is not necessary to designate indoor unit
address when using group control.
The address is automatically set when
power is activated.
Power supply Power supply Power supply
Power supply
single phase Outdoor unit single phase single phase single phase
Control box
208/230V
208/230V
208/230V
208/230V
60Hz
60Hz L1 L2
60Hz L1 L2
60Hz L1 L2
L1 L2
No. 2
System
Most
downstream
indoor unit
Indoor
IN/D OUT/D
F1 F2 F1 F2
unit A
L2 L1 P1 P2 F1 F2 T1 T2
L2 L1
P1 P2 F1 F2 T1 T2
Indoor
unit B
L2 L1 P1 P2 F1 F2 T1 T2
L 2 L 1 P 1 P 2 F1 F2 T1 T2
Indoor
unit C
P1 P 2
P1 P2
Fig. 30
English
For use with 2
remote controllers
P1 P2
21
3P161684-5H
FXFQ-P
35
Installation
EDUS391000-F1
3. When including BRANCHSELECTOR unit
Power supply
single phase
208/230V
60Hz L1
Outdoor unit
Control box
L2
IN/D OUT/D
F1 F2 F1 F2
No. 3
System
Indoor unit A
L2 L1
P1 P2 F1 F2 T1 T2
Power supply
single phase
208/230V
L1 L2
60Hz
BRANCHSELECTOR unit
BRANCHSELECTOR unit
Control box
Control box
OUT/D IN/D
F1 F2 F1 F2
OUT/D IN/D
F 1 F2 F 1 F2
L2 L1
P1 P2
P1 P2 F1 F2 T1 T2
Most
downstream
indoor unit
P1 P2
Fig. 31
[ PRECAUTIONS ]
1. Do not ground the equipment on gas pipes, water pipes or lightning rods, or crossground with telephones.
Improper grounding could result in electric shock.
9-3 Control by 2 remote controllers (controlling 1 indoor unit by 2 remote controllers)
• When using 2 remote controllers, one must be set to “MAIN” and the other to “SUB”.
MAIN/SUB CHANGEOVER
• The settings of the BRC1E71 remote controller should be switched while referring to the manual supplied
with the remote controller.
• In case of the BRC1D71 remote controller.
(1) Insert a
screwdriver into the recess between the upper and lower part of remote controller and, working
from the 2 positions, pry off the upper part. (The remote controller PC board is attached to the upper part
of remote controller.) (Refer to Fig. 32)
(2) Turn the main/sub changeover switch on one of the two remote controller PC boards to “S”. (Leave the
switch of the other remote controller set to “M”.) (Refer to Fig. 33)
Upper part of
remote controller
Insert the screwdriver here and gently work
off the upper part of remote controller.
22
Lower part of
remote controller
Fig. 32
English
3P161684-5H
36
FXFQ-P
EDUS391000-F1
Installation
(Factory setting)
Only one remote controller needs
to be changed if factory settings
have remained untoUched.
S
M
Remote
controller
PC board
S
M
Fig. 33
Wiring Method (See ‘‘ELECTRIC WIRING WORK’’)
(3) Remove the control box lid
(4) Add remote control 2 (slave) to the terminal block for remote controller (P1, P2) in the control box.
(There is no polarity.) (Refer to Fig. 30 and 8-3.)
9-4 Computerised control (forced off and on/off operation)
(1) Wire specifications and how to perform wiring
• Connect the input from outside to terminals T1 and T2 of the terminal block for remote controller.
F2
T1
T2
FORCED
OFF
Input A
Wire specificationCONDUCTORSTRANDEDNONSHIELDEDCOPPERCABLE06#ORVINYLJACKET
Gauge
AWG18 Length
Max. ft.
External terminal
Contact that can ensure the minimum applicable load of 15 V DC, 1 mA.
(2) Actuation
• The following table explains FORCED OFF and ON/OFF OPERATIONS in response to Input A.
FORCED OFF
ON/OFF OPERATION
Input “ON” stops operation (impossible by remote controllers.) Input OFF → ON turns ON unit.
Input OFF enables control by remote controller.
Input ON → OFF turns OFF unit.
(3) How to select FORCED OFF and ON/OFF OPERATION
• Turn the power on and then use the remote controller to select operation.
9-5 Centralized control
• For centralized control, it is necessary to designate the group No. For details, refer to the manual of each
optional controllers for centralized control.
English
23
3P161684-5H
FXFQ-P
37
Installation
EDUS391000-F1
10. INSTALLATION OF THE DECORATION PANEL
Caution:
With a wireless remote controller, field setting and test operation cannot be performed without attaching the decoration panel.
<If performing a test run without attaching the decoration panel, read “11. FIELD SETTING” and “12. TEST
OPERATION” first.>
Refer to the installation manual attached to the decoration panel.
After installing the decoration panel, ensure that there is no space between the unit body and decoration panel.
Note:
Since the electric insulation sheet sticked to the control box lid gets sandwiched between the unit body and
decoration panel, when closing the lid, slip the insulation sheet between them first and then attach the lid to the
control box.
11. FIELD SETTING
CAUTION
When performing field setting or test operation without attaching the decoration panel, do not
touch the drain pump. This may cause electric shock.
• Check that the outdoor unit has been wired properly.
Make sure the control box lids are closed on the indoor and outdoor units.
Field setting must be made from the remote controller and in accordance with installation conditions.
• Setting can be made by changing the “Mode No.”, “FIRST CODE NO.” and “SECOND CODE NO.”.
• For setting procedures and instructions, see “Field settings” provided with the remote controller.
FIELD SET MODE
Mode No.
Field settings
Mode
10
0–01
4–––
8–––
Return
FIRST CODE NO.
Setting
SECOND CODE NO.
11-1 Setting ceiling height
• Select the SECOND CODE NO. that corresponds to the ceiling height “Table 4”.
(SECOND CODE NO. is factory set to “01”.)
Table 4
FXFQ - PVJU
09 · 12 · 18
36 · 48 type
· 24 · 30 type
Standard · All
Ceiling round outlet
height (ft.) High ceiling 1
High ceiling 2
24
≤ 8-3/4
8-3/4 - 10
10 - 11-1/2
Mode No.
Note) 1
FIRST
CODE NO.
13 (23)
0
≤ 10-1/2
10-1/2 - 12
12 - 13-3/4
SECOND
CODE NO.
01
02
03
English
3P161684-5H
38
FXFQ-P
EDUS391000-F1
Installation
Note:
1. “Mode No.” setting is done in a batch for the group. To make or confirm settings for an individual unit, set
the internal mode number in parentheses.
2. The figure of the ceiling height is for the all round outlet. For the settings for four-direction (part of corner
closed off), three-direction and two-direction outlets, see the installation manual and technical guide supplied with the separately sold closure material kit.
11-2 Setting of air direction
• See the installation manual included with the sealing material of air discharge outlet kit, sold separately and
technical guide, for ceiling height settings for two and three-direction air discharge.
(The SECOND CODE NO. is factory set to “01” (all round outlet) before shipping.)
11-3 Settings for Mounting Options
• When installing an option sold separately, refer to the installation manual provided to the option.
11-4 Setting air filter sign
• Remote controllers are equipped with liquid crystal display air filter signs to display the time to clean air filters.
• Change the SECOND CODE NO. according to “Table 5” depending on the amount of dirt or dust in the room.
(SECOND CODE NO. is factory set to “01” for filter contamination-light.)
Table 5
Setting
Air filter contamination-light
Air filter contamination-heavy
No Display
Spacing time of display air filter
sign (long life type)
Approx. 2500 hrs
Approx. 1250 hrs
Mode No.
10 (20)
FIRST CODE
NO.
0
3
SECOND
CODE NO.
01
02
Note:
1. “Mode No.” setting is done in a batch for the group. To make or confirm settings for an individual unit, set
the internal mode number in parentheses.
2. Make settings for “No Display” in cases where no cleaning display is required, e.g., at the time of regular
maintenance servicing.
• The air conditioner is provided with a long life filter as a standard accessory. Explain to the customer the
necessity of cleaning the filter periodically along with the set time for filter cleaning for the prevention of
clogging.
When using wireless remote controllers
• When using wireless remote controllers, wireless remote controller address setting is necessary. Refer to
the installation manual attached to the wireless remote controller for setting instructions.
• Set the remote controller to the field set mode. For details, refer to the “HOW TO SET IN THE FIELD”, in
the remote controller manual.
• When in the field set mode, select mode No. 12, then set the first code (switch) No. to “1”. Then set second
code (position) No. to “01” for FORCED OFF and “02” for ON/OFF OPERATION. (FORCED OFF at factory
set)
English
25
3P161684-5H
FXFQ-P
39
Installation
EDUS391000-F1
12. TEST OPERATION
Refer to the installation manual of the outdoor unit.
• The operation lamp of the remote controller will flash when an malfunction occurs. Check the malfunction
code on the liquid crystal display to identify the point of trouble. An explanation of malfunction codes and
the corresponding trouble is provided in “CAUTION FOR SERVICING” of the indoor unit.
If any of the items in “Table 6” are displayed, there may be a problem with the wiring or power, so check the
wiring again.
Table 6
Remote control display
“Concentrated Management” is lit up
“U4” is lit up
“UH” is lit up
No display
Content
• There is a short circuit at the FORCED OFF terminals (T1, T2).
• The power on the outdoor unit is off.
• The outdoor unit has not been wired for power supply.
• Incorrect wiring for the transmission wiring and / or FORCED
OFF wiring.
• The power on the indoor unit is off.
• The indoor unit has not been wired for power supply.
• Incorrect wiring for the remote controller wiring, the transmission
wiring, and / or the FORCED OFF wiring.
• If the decoration panel is installed on the indoor unit during the test run, check the operation of the swing
flap on the panel.
• In order to protect the indoor unit, instruct the customer not to operate the air conditioner until the interior
work is completed if the interior work has not been finished at the end of the test run.
(If the air conditioner is operated, substances discharged from the paint, adhesive, etc. can contaminate the
indoor unit, and they may cause splashing or leakage of water.)
NOTE
• After the test run is finished, check the items listed in “2. Items to be checked at time of delivery”.
26
English
3P161684-5H
40
FXFQ-P
EDUS391000-F1
Accessories
10. Accessories
Standard Accessories
Name
(1) Drain hose
(2) Metal clamp
Quantity
1 pc.
1 pc.
(3) Washer for
hanger bracket
8 pcs.
(4) Clamp
6 pcs.
(5) Paper pattern
for installation
1 pc.
Also used as
packing material
Shape
Name
(6) Screw (M4)
Quantity
4 pcs.
(7) Washer
fixing plate
4 pcs.
Insulation for
fitting
1 each
Sealing pad
1 each
1 pc.
1 pc.
(10) Large
For paper
pattern for
installation
(8)for gas
pipe
(13) Small
(11) Medium-1
(14)
Shape
(9)for liquid
pipe
(12) Medium-2
Name
Installation guide
Insulation tube
Quantity
1 pc.
1 pc.
Conduit mounting
plate
1 each
(17)
(15)
Shape
(16)
(Other)
Installation manual
Operation manual
(18)
C: 3P161684-5H
FXFQ-P
41
Accessories
EDUS391000-F1
Optional Accessories (For Unit)
Model
Item
FXFQ9PVJU
FXFQ12PVJU
FXFQ18PVJU
Decoration panel
Fresh air
Chamber type
intake kit
FXFQ36PVJU
FXFQ48PVJU
KDBH55K160F
Panel spacer
Replacement
long life filter
FXFQ30PVJU
BYCP125K-W1
Sealing member of air discharge outlet
Filter
related
FXFQ24PVJU
KDBP55H160FA
Nonwoven type
KAFP551K160
Without Tjoint pipe
and fan
KDDP55B160
With T-joint pipe without fan
KDDP55B160K
Branch duct chamber
Chamber connection kit
KDJP55B80
KDJP55B160
KKSJ55KA160
C: 3D070526A
Optional Accessories (For Controls): Refer to booklet of “Controls”.
42
FXFQ-P
Daikin Industries, Ltd.’s products are manufactured for export to numerous countries throughout the
world. Daikin Industries, Ltd. does not have control over which products are exported to and used in a
particular country. Prior to purchase, please therefore confirm with your local authorized importer,
distributor and/or retailer whether this product conforms tot he applicable standards, and is suitable for
use, in the region where the product will be used. This statement does not purport to exclude, restrict or
modify the application of any local legislation.
dddddfdf
Ask a qualified installer or contractor to install this product. Do not try to install the product yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire, or explosion.
Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or
contractor to install those parts and accessories. Use of unauthorized parts and accessories or
improper installation of parts and accessories can result in water or refrigerant leakage, electrical
shock, fire, or explosion.
Read the User’s Manual carefully before using this product. The User’s Manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any inquiries, please contact your local importer, distributor, or retailer.
©
2010 Daikin Industries, Limited.
Daikin® AC Absolute Comfort®, and its design, VRV®, REFNET™, and Quaternity™ are registered trademarks of Daikin Industries, Limited. All rights reserved.
LonWorks® and LON® are registered trademarks of Echelon Corporation. BACnet® is a Data Communication Protocal for Building Automation and Control Networks,
developed under the auspices of the American Society of Heating, Refrigeratin, and Air-Conditioning Engineers (ASHRAE).
ISO 9001 is a plant certification system
defined by the International Organization
for Standardization (ISO) relating to
quality assurance. ISO 9001 certification
covers quality assurance aspects related
to the “design, development, manufacture,
installation, and supplementary service”
of products manufactured at the plant.
ISO 14001 is the standard defined by the
International Organization for Standardization
(ISO) relating to environmental management
systems. Our group has been acknowledged by
an internationally accredited program of
environmental protection procedures and
activities to meet the requirements of
ISO 14001.
AMERICAS
1645 Wallace Drive, Suite 110
Carrollton, TX75006
info@daikinac.com
www.daikinac.com
Specifications, designs and other content appearing in this brochure are current as of March 2011 but subject to change without notice.
EDUS391000-F1
Printed in U.S.A. 3/2011 B AK
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising