EUTECH INSTRUMENTS | CYBERSCAN CON 1500 CONDUCTIVITY METER | Conductivity/Total Dissolved Solids

Conductivity/Total Dissolved Solids
Conductivity/Total Dissolved Solids
A measure of the impurities in water supplies for domestic and industrial use.
Tester
[1] ECTestr® 11; 11+; TDSTestr® 11; 11+
Handheld [1] CyberScan COND 600; 610 [2] CyberScan CON 400; 410 [3] CyberScan CON 11; 110 [4] EcoScan CON 6; TDS 6
Bench
[1] CyberScan CON 6000 [2] CyberScan CON 1500 [3] CyberScan COND 1400 [4] CyberScan CON 510
page | 35
Conductivity/TDS
About Conductivity/TDS
Measurement
About Conductivity Measurement
The Eutech salinity pocket testers SaltTestr™ series are specially
developed to provide direct readings in these applications.
Introduction to Conductivity, TDS and Salinity
Solution
Absolute pure water
Power plant boiler water
Good city water
Ocean water
Distilled water
Deionised water
Demineralised water
Drinking water
Wastewater
Seawater
10 % NaOH
10 % H2SO4
31 % HNO3
Conductivity
0.055 µS/cm
1.0 µS/cm
50 µS/cm
53 mS/cm
0.5 µS/cm
0.1 - 10 µS/cm
0 - 80 µS/cm
0.5 - 1 mS/cm
0.9 - 9 mS/cm
53 mS/cm
355 mS/cm
432 mS/cm
865 mS/cm
Conductivity is used widely to determine the level of impurities in water
supplies for domestic consumption as well as industrial use. Industries
that employ this method include the chemical, semi-conductor, power
generation, hospitals, textile, iron and steel, food and beverage, mining,
electroplating, pulp and paper, petroleum and marine industries.
The Principle of Conductivity Measurement
The principle by which instruments measure conductivity is simple – two
plates are placed in the sample, a potential is applied across the plates
(normally a sine wave voltage), and the current is measured. Conductivity
(G), the inverse of Resistivity (R) is determined from the voltage and
current values according to Ohm’s law.
G = I/R = I (amps) / E (volts)
Since the charge on ions in solution facilitates the conductance of
electrical current, the conductivity of a solution is proportional to its
ion concentration. In some situations, however, conductivity may
not correlate directly to concentration. The graphs below illustrate
the relationship between conductivity and ion concentration for two
common solutions. Notice that the graph is linear for sodium chloride
solution, but not for highly concentrated sulfuric acid. Ionic interactions
can alter the linear relationship between conductivity and concentration
in some highly concentrated solutions.
Sodium Chloride
Conductivity
Electrical Conductivity (EC) meters measure the capacity of ions in an
aqueous solution to carry electrical current. As the ranges in aqueous
solutions are usually small, the basic units of measurements are
milliSiemens/cm (mS/cm) and microSiemens/cm (µS/cm).
Specific applications include chemical streams, demineraliser output,
reverse osmosis, stream boilers, condensate return, waste streams,
boiler blowdown, cooling towers, desalinisation, laboratory analysis, fruit
peeling and salinity level detection in oceanography.
The total TDS is a mass estimate and is dependent on the mix of chemical
species as well as the concentration while conductivity is only dependent
on the concentration of chemical species. Some applications require
the measurement of Total Dissolved Solids (TDS) in mg/L, parts per
million (ppm) or parts per thousand (ppt). The TDS concentration can
be obtained by multiplying the conductivity value with a factor which
is empirically determined.
Eutech offers meters that allow the direct reading of TDS values.
These include the TDSTestr™ series, EcoScan TDS 6, CyberScan standard
handheld CON 11, CON 110 and waterproof handheld CON 410. Bench
meters for advanced level laboratory research are the CyberScan
CON 510, CON 1500 and colour touchscreen research-grade CON 6000.
Salinity measurements are common in industries like agriculture,
aquaculture, hydroponics, food, pools and spas where it is necessary to
monitor the salt level constantly. The values are usually read in parts per
thousand (ppt) or % (1 ppt = 1 gram per litre).
page | 36
Ion Concentration
Sodium Chloride
Sulfuric Acid
Conductivity
Eutech offers a wide range of conductivity meters for these various
applications. Models include the ECTestr™ series, EcoScan CON 6,
CyberScan handheld CON 11 and CON 110, CyberScan waterproof
CON 400 and CON 410 and CyberScan bench meters CON 510,
CON 1500, CON 6000 as well as the handheld multi-parameters
PC 10, PC 300, PC 510 and colour touchscreen research-grade
bench series PC 6000, PC 6500 and PCD 6500.
No
n
tio
u
l
So
on
cti
a
r
te
In
on
io
lut
So
n
c ti
era
t
In
Ion Concentration
Sulfuric Acid
Units of Measurement
The basic unit of conductivity is the Siemens (S), formerly called the
mho. Since cell geometry affects conductivity values, standardized
measurements are expressed in specific conductivity units (S/cm) to
compensate for variations in electrode dimensions. Specific conductivity
(C) is simply the product of measured conductivity (G) and the electrode
cell constant (L/A), where L is the length of the column of liquid between
the electrode and A is the area of the electrodes.
Conductivity/TDS
About Conductivity/TDS
Measurement
accuracy for measuring pure water.
The Eutech EC620165 4-cell conductivity electrode (cell constant
K=1.0) with in-built ATC and DIN connector is available for use
with the bench meters CON 1500, PC 6000, PC 6500 and PCD 6500.
ECCONSEN9203J 4-cell conductivity electrode with ATC and 3 m
cable is available for COND 600, COND 610, PCD 650 and CD 650
handheld meters.
Important Features to Consider in a Conductivity Meter
Figure 1
• Auto-Ranging
Meter automatically selects the appropriate range for measurement.
There is no need to change the dial, multiply values on the display, or
turn the potentiometer.
C = G x (L/A)
If the cell constant is 1 cm-1, the specific conductivity is the same as
the measured conductivity of the solution. Although electrode shapes
vary, an electrode can always be represented by an equivalent
theoretical cell.
Conductivity Temperature Compensation
Conductivity measurements are temperature dependent. The degree to
which temperature affects conductivity varies from solution to solution
and can be calculated using the following formula:
Gt = Gtstd {1 + α(T-Tstd)}
where:
Gt =
Gtstd =
α
=
Tstd =
Conductivity at measured Temperature T in °C;
Conductivity at Reference (Normalisation) Temperature Tstd in °C;
Temperature Coefficient of solution at Tstd in °C;
Reference or Normalisation Temperature in °C
All meters have either fixed or adjustable automatic temperature
compensation referenced to a standard temperature – usually 25 °C.
Most meters with fixed temperature compensation use α of 2 % per °C
(the approximate α of NaCl solutions at 25 °C). Meters with adjustable
temperature compensation let you to adjust the α to more closely match
the α of your measured solution.
Conductivity Meter Calibration and Cell Maintenance
• Temperature Compensation
A cell with built-in temperature sensor allows the meter to make
adjustments to the conductivity or TDS readings based on changes in
solution temperature.
• TDS Conversion Factor
When a solution does not have a similar ionic content to natural water
or salt water, then a TDS conversion factor is needed to automatically
adjust the readings.
• Adjustable Temperature Coefficients
The TDS of certain samples, such as alcohols and pure water, are affected
by changes in temperature. An adjustable temperature coefficient
allows the user to compensate for temperature changes on the solution
being measured.
• Adjustable Cell Constant
Adjusts the reading on the display to reflect use of a cell with a constant
other than k=1.0 cm-1.
Eutech’s wide range of conductivity meters incorporates these
features for consistent, accurate and reliable measurements.
<< Photo Development
>> Industrial Boilers
Conductivity meters and cells should be calibrated to a standard solution
before using. When selecting a standard, choose one that has the
approximate conductivity of the solution to be measured.
A polarized or fouled electrode must be cleaned to renew the active
surface of the cell. In most situations, hot water with a mild liquid
detergent is an effective cleanser. Acetone easily cleans most organic
matter, and chlorine solutions will remove algae, bacteria or molds. To
prevent cell damage, abrasives or sharp objects should not be used to
clean an electrode. A cotton bud works well for cleaning but care must
be taken not to widen the distance of cell.
Conductivity Cells
Most conductivity meters have a 2-cell electrode available in either dip or
flow-through styles. The electrode surface is usually platinum, titanium,
gold-plated nickel, or graphite. The 4-cell electrode uses a reference
voltage to compensate for any polarization or fouling of the electrode
plates. The reference voltage ensures that measurements indicate actual
conductivity independent of electrode condition, resulting in higher
page | 37
Conductivity/TDS
Pocket Tester
Conductivity/ºC/ºF
Conductivity/ºC/ºF
* For ECTestr 11+ & TDSTestr 11+
TDS/ºC/ºF
Unique cup-style design
of ‘+’ series allows
you to hold small
volumes of sample
ECTestr® 11 ; ECTestr® 11+ ; TDSTestr® 11 ; TDSTestr® 11+
TDS/ºC/ºF
Offering one of the best accuracies among pocket-sized conductivity and TDS meters today, the
ECTestr® 11 series and TDSTestr® 11 series come with ±1 % full scale accuracy over a broad
measurement range. Handy, IP67-waterproof and long-lasting, the testers are so light, they float!
Sim
Simultaneous
temperature displayy
tem
VALOX® sensor
casing for
fo superior
chemical durability
Sensor element
made from industrial
strial
grade SS316 stainless
nless
tect
steel type to protect
mples
against harsh samples
Dip-type sen
sensor for
the non-’+’ m
models
High Accuracy
• TDSTestr 11+ series measures up to 10.00 ppt
• ECTestr 11+ series measures up to 20.00 mS/cm
• Selectable TDS factor (0.40 to 1.00) for TDSTestr 11 series
• Selectable single/multi-point calibration with auto/manual options
• ±1 % full scale accuracy
Applications
Long Lasting
• Reduced operating cost – use tester body again and again with user-replaceable sensor
• Rugged and waterproof to IP67 standards. So light, it floats!
• Water & wastewater treatment • Boiler
blow-down • Electroplating rinse tanks
• Drinking water • Hydroponics • Printing
Industry • Aquaculture • Aquariums & fish
farms • Swimming pools • Others
User-Friendly
• Auto-ranging capabilities options with convenient direct readout and optional range selection
• Temperature display with ºC and ºF options – no need for separate thermometer!
• Non-volatile memory retains tester settings, even when batteries run out
page | 38
Conductivity/TDS
Pocket Testers
Specifications
EC Waterproof Large Dual-Display Pocket Tester
ECTestr 11+
ECTestr 11
TDS Waterproof Large Dual-Display Pocket Tester
TDSTestr 11+
TDSTestr 11
Conductivity/
TDS
Pocket Testers
Specifications
Measuring Parameter
Highlights
Range
Conductivity
Resolution
Accuracy
TDS
Conductivity / ºC / ºFF
Cond
Multi-range
Dual-range
.. to 200.0 µS/cm
.. to 2000 µS/cm
.. to 2000 µS/cm
.. to 20.00 mS/cm
.. to 20.00 mS/cm
0.1 µS/cm
10 µS/cm
1 µS/cm
0.10 mS/cm
0.01 mS/cm
±1 % full scale
Range
–
Resolution
–
Accuracy
Factor
–
–
3 auto, 3 manual
Cal. Points
Range
Resolution
Temperature Accuracy
Calibration
Window
Temperature
Compensation
Sensor Type
Temperature
Coefficient
Normalization
Temperature
Non-Volatile
Meter
Memory
Features
IP67
Operating
Temperature
Auto-Off
LCD Display
Power
Battery Life
Dimensions Tester
(LxWxH); Weight Boxed
TDS / ºC / ºF
Multi-range
Dual-range
–
–
–
.. to 100.0 ppm *
.. to 1000 ppm *
.. to 1000 ppm *
.. to 10.00 ppt
.. to 10.00 ppt
(depending on TDS factor)
0.1 ppm
10 ppm
1 ppm
0.10 ppt
0.01 ppt
±1 % full scale
0.40 to 1.00 (selectable)
2 auto, 2 manual
3 manual
2 manual
0 to 50.0 ºC / 32.0 to 122.0 ºF
0.1 ºC / 0.1 ºF
±0.5 ºC / ±0.9 ºF + 1 LSD
±5.0 ºC / ±9.0 ºF
ATC (0 to 50 ºC / 32.0 to 122.0 ºF)
Cup
ATC (0.0 to 50.0 ºC / 32.0 to 122.0 ºF)
Dip
Cup
Dip
2 % per ºC
25.0 ºC
Yes
Yes
0.0 to 50.0 ºC
8.5 mins after last key pressed
Custom dual-display (2.1 x 2.7 cm)
4 x 1.5 V ‘A76’ micro alkaline batteries
> 150 hrs
16.5 x 3.8 cm ; 90 g
18.5 x 6.5 x 5 cm ; 200 g
• 1 mS/cm = 1000 µS/cm (µS: microSiemens / mS: miliSiemens) • 1 ppt = 1000 ppm (ppm: parts per million / ppt: parts per thousand) * Max. 200.0 ppm and 2000 ppm based on TDS factor 1.0
<< Hydroponics
<< Fish Farms
page | 39
Conductivity/TDS
Pocket Testers
Ordering Information
Conductivity/TDS Pocket Testers
•
•
•
•
•
•
•
•
•
•
•
•
Alkaline Button
Cell Batteries
01X377227
01X377226
01X377234
01X377233
Lanyard
ECTEST11PLS
ECTEST11
TDSTEST11PLS
TDSTEST11
Cup Type Sensor
(ECTDSSENSORPLUS)
ECTestr 11+
ECTestr 11
TDSTestr 11+
TDSTestr 11
Temperature
Part No.
TDS
Order Code
Conductivity
Item
Accessories
2-Pin Type Sensor
(ECTDSSENSOR)
Sensors
Parameters
•
•
•
•
•
•
•
•
Replacement Sensors & Electrodes
Used With
Description
ECTestr 11 / TDSTestr 11 / SaltTestr 11 2-pin type replacement sensor
ECTestr 11+ / TDSTestr 11+
Cup type replacement sensor
Order Code
Part No.
ECTDSSENSOR
01X229713
ECTDSSENSORPLUS 01X229714
Accessories
Used With
All testers
All testers
Order Code
ECPOUCH01
ECBATT14
Description
Carrying pouch for pocket tester
Alkaline button cell batteries (50 units per pack)
<< Drinking Water
<< Swimming Pools
page | 40
>> Aquaculture
>> Industrial Process Water
Part No.
56X201300
01X220401
Conductivity/TDS
CyberScan
Waterproof Handheld
High/low alarm limits
User-friendly set-up
menu with intuitive
soft-key operation
IP67 waterproof
Conductivity/TDS/Salinity/Resistivity/ºC/ºF
Conductivity/TDS/ºC/ºF
Comprehensive
multi-data screen display
with backlight
CyberScan COND 600 ; CyberScan COND 610
View readings, calibration and electrode status data all in one screen view – the CyberScan
COND 600 series comes with advanced wireless communications technology for seamless data
transfer from meter to PC. Meter also accepts and auto-detects 2-cell and 4-cell conductivity probes
for pure water to wastewater applications.
Wireless data transfer
Kit set comes with 4-cell
conductivity electrode
Complimentary
Cybercomm software
– download data from
meter to PC as text or
Excel® spreadsheet
Velcro strap
for firmer grip
Wider Measuring Range
• Up to 5 Conductivity ranges in one meter with convenient auto-ranging capabilities
• ±1 % full scale accuracy at 3-decimal resolution
• Measures pure water with pure water temperature coefficient option
User-Friendly
• Backlit screen with multi-data display – convenient for working in dark areas
• Cal-due alarm for periodic calibration updates
Advanced Data Management
• Meter logs reading automatically within seconds of measurement
• Password protection security for calibration and set-up menus
• GLP-compliant with time and date-stamping
• RS232C through LED*, IrDA wireless communications technology
* RS232C (LED) interface adapter available as separate accessory (order code: 01X344201)
Applications
Environmental: Use to test water quality,
monitor health of aquatic ecosystems,
survey surface and ground water drinking
supplies and to meet EPA regulations.
Industrial: Ideal for checking quality
of plant water intake and discharge,
wastewater and water treatment,
recirculating systems and industrial process
systems, water conditioning plants and
chemical process verification.
Aquaculture: Use to monitor water
conditions in catfish and shrimp farming,
game stocking ponds, ornamental fish
tanks and ponds as well as other fish
farming applications.
page | 41
Conductivity/TDS
CyberScan
Waterproof Handheld
Ergonomic design for
that perfect palm fit
CyberScan CON 400 ; CyberScan CON 410
Conductivity/ºC/ºF
Conductivity/TDS/ºC/ºF
Waterproof to IP67, the CyberScan CON 400 and 410 deliver lab-accurate results stamped with time
and date for GLP-compliant research.
Rubber grips at
either side for
firmer grip
IP67 – dustproof
and waterproof
Conductivity
electrode with
built-in ATC and
minimal bubble
entrapment design
Available as a
complete kit version
Applications
• Water quality testing • Geological and
ecological testing • Cooling towers • Boiler
water • Printing • Brines • Swimming pools
and spas • Agriculture and aquaculture
• Aquariums • Hydroponics • Fertilizers
• Schools and laboratories
page | 42
•
•
•
•
•
•
•
Conveniently auto-ranging with up to 5-point push-button calibration
Selectable cell constant
GLP-compliant
Selectable automatic/manual temperature compensation
Hold function freezes readings for easy reference
Auto-off conserves energy and lengthens battery life-span
Non-volatile memory holds up to 50 data sets even when you run out of batteries
Expanded Features of CyberScan CON 410
• Measures TDS in addition to Conductivity and Temperature in °C and °F
• Adjustable TDS factor for direct derivation of TDS values
Conductivity/TDS
CyberScan
Standard Handheld
Dual-display
with temperature
annunciator
Ergonomically
nomically
designed
gned for easy
one-hand
hand operation
Splashproof keypad
Conductivity
electrode with
built-in ATC and
designed for minimal
bubble entrapment
IP54-rated housing
protects meter
against dust and
water splashes
• Selectable automatic
t
ti and
d manuall calibration
lib ti options
ti
• Full-range accuracy with up to 5-point push-button calibration
• More accurate measurements with user-customisable options for normalisation temperature,
TDS factor and temperature coefficient
• Non-volatile memory holds up to 50 data sets. Meter settings remain even when you run out
of batteries
• Hold function freezes readings for easy reference
• Auto-off conserves energy and lengthens battery life-span
Expanded Features of CyberScan CON 110
• Convenient data transfer to a printer or PC with RS232C output
• One-glance monitoring of electrode performance with electrode data display
• Expanded memory holds up to 100 data sets
Conductivity/TDS/ºC
Conductivity/TDS/ºC/ºF
CyberScan CON 11 ; CyberScan CON 110
The economy CyberScan CON 11 and 110 are cost-effective, easy to use and self-diagnostic
for easy trouble-shooting. Meters are uniquely designed to fit your palm perfectly for effortless
one-hand operation.
peration.
Direct data printout
via RS232C
Adjustable
electrode holder
Applications
General: Monitor dissolved solids or
Conductivity levels quickly and easily
in laboratories, field, schools and
educational environments.
Industrial: Use for testing pollution control,
water treatment, and water hardness.
Also useful for checking cooling towers,
boiler water, fountain solutions in printing
operations, brines, swimming pools,
whirlpools and rinse water.
Agricultural: Use for checking aquariums,
fish farms, hydroponics, and fertilizer/
chemical concentrations.
page | 43
Conductivity/TDS
EcoScan Handheld
EcoScan CON 6 ; EcoScan TDS 6
EcoScan easy view
Conductivity/ºC
TDS/ºC
Sturdy and economical – the Eutech EcoScan CON 6, TDS 6 are no-frills handhelds perfect for basic
water testing needs. The meters are rugged, sturdy and come with protective rubber boots and
hinges thatt conveniently double up as benchtop stands.
IP54-rated housing
protects against dust
and water splashes
Splashproof keypad
Protective rubber boot
doubles up as meter stand
Conductivity
electrode with
built-in ATC and
designed for minimal
bubble entrapment
Applications
Routine Testing: For quick, accurate
Conductivity or TDS checks in laboratories,
field and schools.
Environmental/Agricultural: Useful in
nutrient and fertilizer checks in hydroponics
and agricultural industries.
Water Quality Testing: For analysing
water, hard water, untreated water,
industrial and rinse water, drinking water,
effluent water, pool water and incoming
process water. Ideal for all types of quality
assurance, printing industries and water
quality testing.
page | 44
• Up to 5-point
oint push-button calibration with auto-buffer recognition – quick, easy calibration
with no mistakes
• ±1 % full scale accuracy
• Selectablee automatic/manual temperature compensation
ging for Conductivity measurements
• Auto-ranging
• Adjustable TDS factor for direct derivation of values
• Non-volatile memory holds meter settings, even when batteries run out
• Easy troubleshooting with comprehensive self-diagnostic messages
Conductivity/TDS
Handheld Meters
Specifications
COND 610
CyberScan Dual-Display
CON 410
CON 400
COND 600
CON 110
EcoScan Single-Display
CON 6
TDS 6
CON 11
Conductivity/TDS
Handheld Meters
Specifications
Measuring Parameter
Highlights
Range
Conductivity
Resolution
Accuracy
Range
(Depending
On TDS Factor)
TDS
Resolution
Accuracy
TDS Factor
Range
Salinity
Resolution
Accuracy
Range
Resistivity
Resolution
Accuracy
Cal. Points
Temperature
Meter
Features
Range
Resolution
Accuracy
Compensation
Normalization
Operating Temp.
Temperature
Coefficient
GLP
Cal-Due Alarm
IP67
Datalogging
Memory
Cell Constant
LCD Display
Auto-Off
Auto Hold
Input
Output
Power
Battery Life
Dimensions Meter
(LxWxH); Weight Boxed
Conductivity
Conductivity
Conductivity
C
d i i /TDS
/TDS /
C
Condu
onductivity / Con
nductivity / TDS / Conductivity
nduct
C
Conductiv
vity /
Conductivity
Conductivity / TDS
DS / ºC / ºF
Conduct
onductivity / ºC
TDS / ºC
ºC / ºF
TDS / ºC
Salinity/Resistivity/ºC/ºF
ºC / ºF
º
Expanded
Waterproof, GLP, Waterproof, GLP,
Standard
Economical CON Economical TDS
RS232C, IrDA,
Waterproof, GLP
memory, RS232C
RS232C, IrDA,
handheld
measurement
measurement
linear TC
output
linear & pure TC
.. to 2.000 µS/cm .. to 2.000 µS/cm
.. to 19.99 µS/cm
2.000 to 300.0 µS/cm 2.000 to 300.0 µS/cm
19.9 to 199.9 µS/cm
–
199 to 1999 µS/cm
300.0 µS/cm to 4.000 mS/cm 300.0 µS/cm to 4.000 mS/cm
2.00 to 19.99 mS/cm
4.000 to 40.00 mS/cm 4.000 to 40.00 mS/cm
20.0 to 199.9 mS/cm
40.00 to 500.0 mS/cm 40.00 to 200.0 mS/cm
0.01 µS/cm / 0.1 µS/cm / 0.001 mS/cm /
0.05 % full scale
0.01 mS/cm / 0.1 mS/cm
±1 % full scale + 1 LSD
.. to 9.99 ppm **
.. to 9.99 ppm **
.. to 2.000 ppm
.. to 10.00 ppm **
.. to 2.000 ppm
10.0 to 99.9 ppm
10.0 to 99.9 ppm
2.000 to 300.0 ppm 2.000 to 300.0 ppm 10.0 to 100.0 ppm
100 to 999 ppm
–
100 to 999 ppm
–
300.0 ppm to 4.000 ppt 300.0 ppm to 4.000 ppt 100 to 1000 ppm
1.00 to 9.99 ppt
1.00 to 9.99 ppt
4.000 to 40.00 ppt 4.000 to 40.00 ppt 1.00 to 10.00 ppt
10.0 to 99.9 ppt
10.0 to 99.9 ppt
40.00 to 500.0 ppt 40.00 to 200.0 ppt 10.0 to 100.00 ppt
0.01 ppm / 0.1 ppm / 0.001 ppt /
0.05 % full scale
–
0.05 % full scale
0.01 ppt / 0.1 ppt
±1 % full scale + 1 LSD
–
±1 % full scale + 1 LSD
0.40 to 1.00
0.40 to 1.0
–
0.40 to 1.0
–
0.40 to 1.0
.. to 0.770 ppm
0.770 to 143.3 ppm
143.3 ppm to 2.138 ppt
–
2.138 to 23.64 ppt
23.64 to 80.00 ppt
0.01 ppm / 0.1 ppm /
–
0.001 ppt / 0.01 ppt
±1 % full scale + 1 LSD
–
2.000 to 25.00 Ω
25.00 to 250.0 Ω
–
250.0 to 3.333 kΩ
3.333 to 500.0 kΩ
500.0 kΩ to 20.00 MΩ
0.01 Ω / 0.1 Ω / 0.001 Ω /
–
0.1 Ω / 0.01 MΩ
1 % full scale + 1 LSD
–
4 (1 per range) auto, 5 (1 per range) manual
5 (1 per range) manual
4 (1 per range) auto, 5 (1 per range) manual
5 (1 per range) manual
-10.0 to 110 ºC / 14.0 to 230 ºF
0.0 to 100.0 ºC / 32.0 to 212 ºF
0.1 ºC / 0.1 ºF
±0.5 ºC / ±0.9 ºF
ATC / MTC (0 to 80 ºC)
15 to 30 ºC
20.0 or 25.0 ºC
0 to 50 ºC
Linear & pure
Linear
0.0 to 10.0 %
0.0 to 3.0 %
Yes
–
Yes
–
Yes
–
Yes
500 data sets
0.010 to 10.000
Dot-matrix LCD with backlight
(5.4 x 7.1 cm)
2 to 30 mins after last key pressed
–
50 data sets
100 data sets
50 data sets
0.1, 1.0, 10.0
Dual-display LCD
(5.8 x 3.3 cm)
20 mins after last key pressed
Yes
DC phono sockets, 8-pin connector
IrDA, RS232C (via LED) *
4 x 1.5 V ‘AA’ alkaline batteries or
9 V DC adapter, 500 mA
> 200 hrs
18.3 x 9.5 x 5.7 cm ; 460 g
40 x 33 x 10 cm ; 2680 g
6-pin connector
–
DC socket, 6-pin connector
RS232C
4 x 1.5 V ‘AAA’ alkaline batteries or
4 x 1.5 V ‘AAA’ alkaline batteries
9 V DC adapter, 200 mA
> 100 hrs
> 200 hrs
19 x 10 x 6 cm ; 320 g
18 x 9 x 4 cm ; 220 g
40 x 33 x 10 cm ; 2100 g
–
Single-display LCD
(4.5 x 2.3 cm)
–
BNC, 2.5 mm phono socket
–
4 x 1.5 V ‘AAA’ alkaline batteries
> 100 hrs
14 x 17 x 3.5 cm ; 200 g
36 x 28 x 8 cm ; 1500 g
• 1 mS/cm = 1000 µS/cm (µS: microSiemens / mS: miliSiemens) • 1 ppt = 1000 ppm (ppm: parts per million / ppt: parts per thousand) ** Maximum 199.9 ppt depending on factor setting
* RS232C (LED) interface adapter available as separate accessory (see page 46 for order information)
page | 45
Conductivity/TDS
Handheld Meters
Ordering Information
Conductivity/TDS Handheld Meters
Replacement Electrodes
Used With
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Description
4-cell epoxy body Conductivity electrode, ATC, cell constant K=1.0, 12 x 120 mm, 8-pin connector,
3 m cable
2 stainless steel rings ultem-body Conductivity electrode, ATC, cell constant K=1.0, 16 x 144 mm,
8-pin connector, 1 m cable
2 stainless steel rings ultem-body Conductivity electrode, ATC, cell constant K=1.0, 16 x 144 mm,
6-pin connector, 1 m cable
2-stainless steel rings ultem-body Conductivity electrode , ATC, cell constant K=1.0, 16 x 144 mm,
BNC connector, 1 m cable
Order Code
12 mm diameter electrode
All except CyberScan 600 series
Description
CyberScan CON 600 series carry kit set – plastic carry case, 442 standard solutions (1413 mS,
12.88 mS KCl, 3000 ppm), deionised rinse water
100 / 240 VAC SMPS power adapter, 9 V, 6 W, centre +ve, US / UK / EUR / Japan plug
RS232C (LED) interface adapter
CyberScan Conductivity / TDS carry kit set – plastic carry case, 442 standard solutions (1413 mS,
12.88 mS KCl, 3000 ppm), deionised rinse water
100 / 240 VAC SMPS power adapter, 9 V, 6 W, centre +ve, US / UK / EUR / Japan plug
RS232C communication cable – 9-pin male to 9-pin female connector, 1 m cable
EcoScan Conductivity / TDS carry kit set – plastic carry case, 442 standard solutions (1413 mS,
12.88 mS KCl, 3000 ppm), deionised rinse water
Electrode holder
CyberScan handheld carry pouch
<< Laboratories
<< Agricultural Industries
CyberScan COND 610 / COND 600
CyberScan COND 610 / COND 600
CyberScan CON 410 / CON 400 /
CON 110 / CON 11
EcoScan CON 6 / TDS 6
Accessories
Used With
CyberScan COND 610 / COND 600
CyberScan COND 610 / COND 600
CyberScan COND 610 / COND 600
CyberScan CON 410 / CON 400 /
CON 110 / CON 11
CyberScan CON 110 / CON 11
CyberScan CON 110
EcoScan CON 6 / TDS 6
page | 46
<< Pollution Control
EcoScan Carry
Kit Set With
Calibration Stds
RS232C Cable
Electrode
Holder
CyberComm
Portable
DAS Software
CyberComm 600
DAS Software
•
Conductivity
Electrode
(ECCONSEN91B)
•
CyberScan Carry
Kit Set With
Calibration Stds
•
•
•
Accessories
Power Adapter
•
•
•
•
•
•
•
4-Cell
Conductivity
Electrode
(ECCONSEN9203J)
01X418307
01X418304
01X251412
01X251410
01X366309
01X366305
01X289401
01X289406
Temperature
ECCONWP61043K
ECCONWP60043K
ECCONWP41003K
ECCONWP40003K
ECCON11003K
ECCON1103K
ECCON603K
ECTDS603K
Salinity
COND 610
COND 600
CON 410
CON 400
CON 110
CON 11
CON 6
TDS 6
Resistivity
Part No.
TDS
Order Code
Conductivity
Item
Conductivity
Electrode
(ECCONSEN91W)
Electrodes
Parameters
Part No.
ECCONSEN9203J 01X244723
ECCONSEN91J
01X244721
ECCONSEN91W
01X244702
ECCONSEN91B
01X244701
Order Code
Part No.
ECCONWP600KIT 01X430202
01X030132
91100-85
01X030132
01X344202
ECCONWPKIT
01X266802
60X030130
ECCA02M09F09
60X030130
30X219503
ECECOCONKIT
01X266902
15X000700
ECPOUCH02
15X000700
56X201400
Conductivity/TDS
CyberScan
Premium Bench
Conductivity/TDS/Salinity/Resistivity/ºC/ºF
CyberScan CON 6000
Send data to any computer in the world directly from your meter! Eutech’s CyberScan 6000 Series is the
world’s first Windows CE-driven touchscreen meter series with internet/ethernet-ready connection.
With its comprehensive communications capabilities, you can choose to send data in any format
– via the USB port, wirelessly using IrDA, or email via the internet.
World’s first Windows® CE-driven
colour touchscreen bench meter
Detachable electrode
holder can be fixed on
either side of meter
Application software
with technical controls for
21 CFR Part 11
(software sold separately)
Internet/ethernetready connection
Multiple communications
capabilities
Real-time
on-screen graphing
Touchscreen
efficiency
Stores up to
1000 data sets
per parameter
• Single-point and multi-point standardisation for Conductivity, Resistivity, TDS and Salinity
measurements using 2-cell and 4-cell probes
• Advanced real-time on-screen graphing function provides useful indication for
specific measurements
• Extensive setup screens enable you to customise meter to your needs, e.g. cell constant, temperature
coefficient, TDS factor, alarm limits and other functions
• Windows® CE-driven, full-color touchscreen provides unmatched ease of use in operations and
setups with user-friendly icons, user prompts and context specific ‘help’ screens
• Advanced USB, IrDA connectivity allows extensive host/device communication capabilities
• Secure log-in for up to ten users
1 year warranty for touchscreen
display; 3 years warranty for all
other meter components.
Applications
• Pharmaceutical manufacturing • Research
and lab course work • Forensic analysis
• Life sciences and medical researches
• Environmental testing labs • Wastewater
and drinking water facilities • Food
processing and beverage production
page | 47
Conductivity/TDS
CyberScan
Deluxe Bench
CyberScan CON 1500
Conductivity/TDS/Resistivity/ºC/ºF
High-end conductivity measurement in the laboratory is simple with Eutech’s CyberScan CON 1500.
Featuring auto-standardisation, auto-calibration, and auto-ranging capabilities, the bench meter
accepts 2-cell and 4-cell electrodes, giving you a broad range of measurement at ±0.5 % full scale
accuracy. Meter comes with bi-directional RS232C capabilities for two way communication with
computer or printer, and a complimentary Data Acquisition Software (DAS) that allows you to work
on meter remotely via your computer.
GLP-compliant
software that allows
input of serial
number, operator ID
and company name
Large characters
provide clear wide
viewing angle
Tactile keypad
ensures efficient
meter operation
Bi-directional RS232C
communication to PC
with DAS
Detachable electrode
stand organises
multiple electrodes
neatly and holds
them firmly in place
Applications
• Environmental studies • Chemical
laboratories • Quality assurance testing
• Food science • Ecological studies
• Education institution
page | 48
Scratch-resistant
screen offers
high durability
• Choose convenient auto-calibration with preset calibration values or manual multi-point calibration
for greater flexibility and precision
• Standardisation is a breeze – meter features auto-standardisation, allowing you to detect the exact
cell constant value of your electrodes with one button pressed
• Monitoring efficiency of your probe is easy with the effective cell constants display
• Built-in replatinizing circuit – quick, hassle-free replatinization in 5 minutes
• Meter comes with 4-cell electrode with built-in ATC – no need for separate ATC electrode
Conductivity/TDS
CyberScan
Deluxe Bench
High-end conductivity measurement at an economical price! Eutech’s CyberScan COND 1400
features auto-standardisation, auto-calibration, and auto-ranging capabilities, and accepts 2-cell
and 4-cell electrodes – a must-have for researches on a budget.
• Choose convenient auto-calibration with preset calibration values or manual multi-point calibration
for greater flexibility and precision
• Standardisation is a breeze – meter features auto-standardisation, allowing you to detect the exact
cell constant value of your electrodes with one button pressed
• Monitoring efficiency of your probe is easy with the effective cell constants display
• Built-in replatinizing circuit – quick, hassle-free replatinization in 5 minutes
• Meter comes with 2-cell electrode with built-in ATC – no need for separate ATC electrode
Conductivity/TDS/ºC/ºF
[Available in Q2 2008]
CyberScan COND 1400
NEW!
Applications
• Environmental studies • Chemical
laboratories • Quality assurance testing
• Food science • Ecological studies
• Education institution
page | 49
Conductivity/TDS
CyberScan
Economy Bench
Dual-display LCD
CyberScan CON 510
Conductivity/TDS/ºC/ºF
The economy CyberScan 510 series offers high precision and stability for years of reliable, value-formoney performance. The CON 510 is an affordable meter for accurate and consistent measurement
of conductivity in the laboratory, and is great for labwork in school as well.
Save limited bench
space with multielectrode holder
IP54-rated
splashproof housing
and keypad
Quick reference slide-out
instruction card
Non-skid pads
hold meter steady
during operation
Straightforward
keypad design
ensures easy
operation
Applications
Routine Testing: For quick, accurate
Conductivity or TDS checks in laboratories,
field and schools.
Industrial: For checking metal finishing,
solutions, cooling tower water, printing
fountain solutions, boiler water, brines,
drilling mud, rinse tanks, ponds, pollution
control, recirculating systems, waste water
and industrial process systems.
Water Quality Testing: For analyzing hard
water, untreated water, drinking water,
effluent water, pool water and incoming
process water. Ideal for all types of quality
assurance and water quality testing.
page | 50
•
•
•
•
•
•
•
•
•
High performance economy bench meter
Selectable cell constant
Custom dual display LCD
Available with built-in electrode stand
Up to 5-point push button calibration
Auto-ranging across 5 ranges
Menu-driven set-up for stress-free user-customisation
Expanded memory of up to 100 data sets
Other features include: Hold function, self diagnostic messages, ‘ready’ indicator, selectable
ATC/MTC, quick reference slide out instruction card
Conductivity/TDS
Bench Meters
Specifications
CON 6000
CyberScan Premium Bench
CON 1500
CyberScan Economy Bench
CON 510
COND 1400
Conductivity/
TDS
Bench Meters
Specifications
Measuring Parameter
Highlights
Range
Conductivity
Conductivity / TDS / Salinity /
Resistivity / ºC / ºF
Windows® CE, single-channel
color touchscreen
Conductivity / TDS /
Resistivity / ºC / ºF
.. to 200.0 µS/cm
200.0 µS/cm to 2.000 mS/cm
2.000 to 20.00 mS/cm
20.00 to 500.0 mS/cm
.. to 200.0 µS/cm
200.0 to 2000 µS/cm
2.000 to 20.00 mS/cm
20.00 to 500.0 mS/cm
TDS
Resolution
Range
Resistivity
Resolution
Salinity (Salt)
Range
Resolution
Accuracy
Temperature
Range
Resolution
Accuracy
Coefficient
(Per ºC)
Normalization
0.001 resolution, extensive display
Economical, high performance
.. to 19.99 µS/cm
20.0 to 199.9 µS/cm
200 to 1999 µS/cm
2.00 to 19.99 mS/cm
20.0 to 199.9 mS/cm
0.01 / 0.1 µS/cm
0.01 / 0.1 mS/cm
.. to 9.99 ppm
Maximum 199.9
10.0 to 99.9 ppm
ppt depending
100 to 999 ppm
on
1.00 to 9.99 ppt
factor setting
10.0 to 99.9 ppt
0.01 ppm / 0.1 ppm / 1 ppm,
0.01 ppt / 0.1 ppt
.. to 200.0 µS/cm
0.000 to 200.0 µS/cm
200.0 µS/cm to 2.000 mS/cm
2.000 to 20.00 mS/cm
20.00 to 500.0 mS/cm
0.001 / 0.01 / 0.1 µS/cm
0.001 / 0.01 / 0.1 mS/cm
Resolution
Range
(Depending
On TDS Factor)
Conductivity / TDS / ºC / ºF
.. to 20.00 ppm
.. to 200.0 ppm
.. to 199.9 ppm
2.000 to 200.0 ppm
200.0 to 2000 ppm
200.0 to 1999 ppm
200.0 to 2000 ppm
2.000 to 20.00 ppt
2,000 to 19999 ppm
2000 to 20000 ppm
20.00 to 500.0 ppt
20,000 to 99999 ppm
20000 to 99999 ppm
Depending on TDS factor
0.001 / 0.01 / 0.1 ppm,
0.001 / 0.01 / 0.1 / 1 ppm
0.001 / 0.01 / 0.1 ppt
0 to 19.99 kΩ
0.000 to 19.99 kΩ
20.00 to 199.9 kΩ
20.00 to 199.9 kΩ
200.0 kΩ to 1.999 MΩ
200.0 kΩ to 1.999 MΩ
2.000 to 100.0 MΩ
2.000 to 100.0 MΩ
0.1 / 0.01 / 0.001 kΩ,
0.01 / 0.001 MΩ
0 to 90 ppt over 4 ranges
–
0.1 / 0.01 / 0.001 ppt
–
±0.5 % full scale + 1 digit
±0.5 % full scale
-5.0 to 105.0 ºC / 23.0 to 221.0 ºF (meter)
0.1 ºC / 0.1 ºF
±0.2 ºC / ±0.3 ºF
±0.3 ºC / ±0.5 ºF
Cal. Points
Temperature
ATC / MTC (-5 to 100 ºC) (meter)
Compensation
GLP
Yes
Cell Constant
Datalogging
Yes
Memory
Up to 1000 data sets per parameter
Automatic
Yes
Endpoint
Meter
Operating
Features
5 to 45 ºC / 41 to 113 ºF
Temperature
Windows® CE colour touchscreen
LCD Display
(11.43 x 15.24 cm)
DC socket, DIN connector
Input
SD reader, USB, RJ45, phono
Output
USB, IrDA, RS232C
9 V DC adapter, 3.3 A
Power
(100 / 240 VAC, SMPS)
16.5 x 23.5 x 8.9 cm ; 1100 g
Dimensions Meter
(LxWxH); Weight Boxed
49 x 28 x 16 cm ; 3330 g
–
–
±1 % full scale
0.0 to 80 ºC (with supplied probe)
±0.5 ºC / ±0.9 ºF
0.000 to 10.000 %
0.0 to 10.0 %
15.0 to 30.0 ºC / 59.0 to 86.0 ºF
4 auto, 4 manual
4 auto, 5 manual
ATC / MTC (0 to 80 ºC)
(with supplied probe)
ATC / MTC (0 to 100 ºC) (meter)
–
0.1 / 1.0 / 10.0
–
–
100 data sets
100 data sets
–
Yes
0 to 50 ºC / 32 to 122 ºF
Scratch-proof LCD with backlight
(7.2 x 10.6 cm)
DC socket, DIN connector
2-pin connector, phono
RS232C
12 V DC adapter, 300 mA
(100 / 240 VAC, SMPS)
19.5 x 14 x 8.5 cm ; 950 g
49 x 28 x 16 cm ; 2510 g
Dual-display LCD with backlight
(5.9 x 3.2 cm)
DC socket,
6-pin connector
–
9 V DC adapter, 300 mA
(100 / 240 VAC, SMPS)
23 x 18 x 6 cm ; 750 g
41.5 x 25.5 x 9 cm ; 1100 g
• 1 mS/cm = 1000 µS/cm (µS: microSiemens / mS: miliSiemens) • 1 ppt = 1000 ppm (ppm: parts per million / ppt: parts per thousand)
page | 51
Conductivity/TDS
Bench Meters
Ordering Information
Conductivity/TDS Bench Meters
•
•
•
•
•
•
•
•
•
•
Available in Q2 2008
01X305204
Replacement Electrodes
Used With
CyberScan CON 6000 / CON 1500
CyberScan CON 510
Accessories
Used With
CyberScan CON 6000 / CON 1500
CyberScan CON 6000
CyberScan CON 6000
CyberScan CON 6000
CyberScan CON 6000
CyberScan CON 1500
CyberScan CON 510
CyberScan CON 510
•
•
•
•
•
Description
4-cell epoxy-body Conductivity electrode, ATC, cell constant K=1.0, DIN connector, 1 m cable
2 stainless steel rings ultem-body Conductivity electrode, ATC, cell constant K=1.0, 16 x 144 mm,
6-pin connector, 1 m cable
Order Code
EC620165
Part No.
93X219046
ECCONSEN91W
01X244702
Description
RS232C communication cable – 9-pin male to 9-pin female connector, 1 m cable
CyberComm 6000 (21 CFR Part 11 compliant CyberScan 6000 series application software)
100 / 240 VAC SMPS power adapter, 9 V, 3.3 A, centre -ve with 2-pin power cord
USB flash drive, 256 MB
SD memory card, 256 MB, Sandisk
100 / 240 VAC SMPS power adapter, 12 V, 6 W, centre -ve with US / UK / EUR / Japan plug
110 / 120 VAC power adapter (50 / 60 Hz) 2-flat pin US type, 9 VDC 500 mA
220/230 VAC power adapter (50 / 60 Hz) 2-round pin Euro type, 9 VDC 500 mA
Order Code
ECCA02M09F09
ECDAS6000
60X030128
01X420001
01X419901
60X030131
60X030111
60X030112
Part No.
30X219503
01X415501
60X030128
01X420001
01X419901
60X030131
60X030111
60X030112
<< Water Analysing
<< Cooling Tower Water
>> School Laboratories
>> Recirculating Systems
page | 52
•
•
•
•
•
Calibration
Sachets
•
•
•
Power Adapter
•
•
•
RS232C Cable
•
•
•
Integral
Electrode Holder
•
•
CyberComm Pro
V2.4 DAS Software
•
•
•
CyberComm 6000
DAS Software
•
•
•
4-Cell Electrode
(EC620165)
01X373811
01X373805
01X296312
Temperature
ECCON600043SC
ECCON600043S
ECCON150043S
ECCON140043S
ECCON51043S
Resistivity
CON 6000
CON 6000
CON 1500
COND 1400
CON 510
Salinity
Part No.
TDS
Order Code
Conductivity
Item
Accessories
Conductivity
Electrode
(ECCONSEN91W)
Electrodes
Parameters
Salinity
Pocket Tester &
EcoScan Handheld
Salinity/ºC
SaltTestr® 11 ; EcoScan Salt 6
Eutech’s latest SaltTestr® 11 now comes with a new temperature display in °C and °F for easy
reference during your salinity testing. Waterproof to IP67 standard, the SaltTestr® 11 assures
high accuracy readings even in harsh field conditions, from aquaculture
settings
q
g to food
production applications.
Unlikee other
conventional
entional testers,
the SaltTestr®
altTestr® 11
offerss ±1 % full
scale accuracy
More User-Friendly
• Direct temperature readout in °C and °F
• Large screen display
• Battery-level indicator
• Non-volatile memory
Salinity/ºC
High Accuracy
• ±1 % full scale accuracy
• Automatic Temperature Compensation (ATC)
User-replaceable
sensor
More Savings
• Replaceable sensors
• Advanced power-conserving design
With sturdy rubber boot, splash-proof keypad, large custom LCD and rugged carrying case, salinity
testing on the go is a breeze with the EcoScan Salt 6.
Protective rubber
boot doubles up
as stand
Reader-friendly
screen display
IP54-rated housing
protects against
water splashes
Splashproof keypad
• Measures in ppt and %
• Quick and easy push-button calibration
n
• User customisation for normalisation
ent
temperature and temperature coefficient
or minimal
• Electrode with built-in ATC designed for
ement
air bubble entrapment during measurement
• Rugged all-in-one meter kit available
• Other features include:
ics
HOLD function, auto-off, self-diagnostics
Applications
Routine Testing: Fo
For quick, accurate
Salinity measurements
measureme in laboratories,
field and schools.
Testing: Ideal for salt
Water Quality Test
levels in brines, pool
poo water, aquaculture
systems, aquariums (marine fish) and
fish ponds (koi), food
foo processing and
healthcare industries.
industri
page | 53
Salinity
Pocket Tester & EcoScan
Handheld Specifications &
Ordering Information
EcoScan Palmtop Single-Display
Salt 6
Waterproof Pocket Tester Large Dual-Display
SaltTestr 11
Salinity
Pocket Tester
& Handheld
Meter
Specifications
Measuring Parameter
Salinity / ºC
Highlights
Handheld meter for high accuracy and wide range Salinity measurements
1.0 to 50.0 ppt / 0.1 to 5.00 %
Range
Resolution
0.1 ppt / 0.01 %
Salinity
(TDS)/%
Accuracy
±1 % full scale
Cal. Points
1 (manual)
Range
-10.0 to 110 ºC
Resolution
0.1 ºC
Accuracy
±0.5 ºC
Temperature Compensation
ATC / MTC (0 to 50 ºC)
Coefficient
0.0 to 3.0 %
(Per ºC)
Normalization
20.0 ºC and 25.0 ºC (selectable)
Temperature
ATC
Compensation
Sensor Type
2-cell
IP67
–
Operating
0 to 50 ºC
Temperature
Meter
Single-display LCD
LCD Display
Features
(4.5 x 2.3 cm)
Non-Volatile
Yes
Memory
Auto-Off
20 mins after last key pressed
Power
4 x 1.5 V ‘AAA’ alkaline batteries
Battery Life
> 100 hrs
14 x 17 x 3.5 cm ; 200 g
Dimensions Meter
(LxWxH); Weight Boxed
36 x 28 x 8 cm ; 1500 g
Large dual-display
.. to 10.00 ppt
0.10 ppt
0 to 50 ºC / 32 to 122 ºF
0.1 ºC / 0.1 ºF
±0.5 ºC / ±0.9 ºF
ATC (0 to 50 ºC)
2%
25.0 ºC
2-pin
Yes
Dual-display LCD
(2.1 x 2.7 cm)
8.5 mins after last key pressed
4 x 1.5 V ‘A76’ micro alkaline batteries
> 150 hrs
16.5 x 3.8 cm ; 90 g
18.5 x 6.5 x 5 cm ; 200 g
• 1 mS/cm = 1000 µS/cm (µS: microSiemens / mS: miliSiemens) • 1 ppt = 1000 ppm (ppm: parts per million / ppt: parts per thousand)
Salinity Pocket Tester & Handheld Meter
•
•
•
•
Alkaline Button
Cell Batteries
•
•
Lanyard
01X289409
01X377232
EcoScan Salinity
Handheld
Carry Kit Set *
Salt 6
ECSALT603K
SaltTestr 11 SALTTEST11
Part No.
Temperature
Order Code
Salinity
Item
Accessories
Conductivity
Electrode
(ECCONSEN91B)
Electrodes
Parameters
•
•
* EcoScan Salinity carry kit set – plastic carry case, 5 ppt, 25 ppt, 45 ppt NaCl standard solutions, deionised rinse water
Replacement Sensors & Electrodes
Used With
Order Code
Part No.
ECCONSEN91B
01X244701
SaltTestr 11
Description
2 stainless steel rings ultem-body Conductivity electrode, ATC, cell constant K=1.0, 16 x 144 mm,
BNC connector, 1 m cable
2-pin type replacement sensor
ECTDSSENSOR
01X229713
Accessories
Used With
SaltTestr 11
SaltTestr 11
SaltTestr 11
SaltTestr 11
SaltTestr 11
Description
5 ppt NaCl standard solution
25 ppt NaCl standard solution
45 ppt NaCl standard solution
Carrying pouch for pocket tester
Alkaline button cell batteries (50 units per pack)
Order Code
ECNACL5PPT
ECNACL25PPT
ECNACL45PPT
ECPOUCH01
ECBATT14
Part No.
01X211230
01X211231
01X211232
56X201300
01X220401
EcoScan Salt 6
page | 54
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising