Full Line Catalog (Download PDF)

Full Line Catalog (Download PDF)
THE COMPLETE CHOICE
OF EMERGENCY
LIGHTING PRODUCTS.
table of
contents
Company Profile . . . . . . . . . . . . . . . . . . 2-3
MR16 LED Emergency Lighting . . . . . . . 4-5
Nexus® Management System . . . . . . . . . 6-7
n
n
Exit Signs
n
n
n
n
n
n
n
n
n
n
n
Table of contents. . . . . . . . . . . . . . .
Overview. . . . . . . . . . . . . . . . . . . . .
RDE Series . . . . . . . . . . . . . . . . . . .
RXL3 Series. . . . . . . . . . . . . . . . . . .
RAE Series . . . . . . . . . . . . . . . . . . .
RXL33 Series. . . . . . . . . . . . . . . . . .
RSL33 Series . . . . . . . . . . . . . . . . . .
RXL33F Series. . . . . . . . . . . . . . . . .
CSL3000 Series. . . . . . . . . . . . . . . .
CXL3000BIL & CSL3000BIL Series. .
CXL3000B12 Series. . . . . . . . . . . . .
ULTD Series . . . . . . . . . . . . . . . . . .
Legend™ CX2000 Series. . . . . . . . . .
Legend™ CS2000 Series. . . . . . . . . .
CX4000 Series. . . . . . . . . . . . . . . . .
CS4000 Series. . . . . . . . . . . . . . . . .
CX4000BIL & CS4000BIL Series. . . .
RA Series . . . . . . . . . . . . . . . . . . . .
CX5000 Series. . . . . . . . . . . . . . . . .
CS5000 Series. . . . . . . . . . . . . . . . .
CX5 Series. . . . . . . . . . . . . . . . . . . .
CX5000R Series . . . . . . . . . . . . . . .
CX7000 & CS7000 Series. . . . . . . . .
RAC Series . . . . . . . . . . . . . . . . . . .
SM-CX5000 Series. . . . . . . . . . . . . .
SM-CS5000 Series. . . . . . . . . . . . . .
RS Series . . . . . . . . . . . . . . . . . . . .
NEXTN Series . . . . . . . . . . . . . . . . .
CNESTU Series . . . . . . . . . . . . . . . .
CNEXTN & CNSXTN Series . . . . . . .
RSC Series . . . . . . . . . . . . . . . . . . .
SM-NEXTN Series . . . . . . . . . . . . . .
R-SN Series. . . . . . . . . . . . . . . . . . .
LD12E Series. . . . . . . . . . . . . . . . . .
LD12S Series. . . . . . . . . . . . . . . . . .
RP Series . . . . . . . . . . . . . . . . . . . .
Ultima™ Exit Series. . . . . . . . . . . . . .
RCS Series . . . . . . . . . . . . . . . . . . .
RCSC Series . . . . . . . . . . . . . . . . . .
Ultima™ Combo Series. . . . . . . . . . .
CS9000N Series . . . . . . . . . . . . . . .
CX9000BIL & CS9000BIL Series. . . .
LD6-IF Series . . . . . . . . . . . . . . . . .
RN Series . . . . . . . . . . . . . . . . . . . .
TUF Series . . . . . . . . . . . . . . . . . . .
RNC Series . . . . . . . . . . . . . . . . . . .
N-TUF Series. . . . . . . . . . . . . . . . .
RH Series . . . . . . . . . . . . . . . . . . . .
TUFHZ Series . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . 11
12-13
14-15
16-17
. . 18
. . 19
. . 20
. . 21
. . 22
. . 23
. . 24
. . 25
. . 26
. . 27
. . 28
. . 29
. . 30
. . 31
. . 32
. . 33
. . 34
. . 35
36-37
38-39
. . 40
. . 41
. . 42
. . 43
. . 44
. . 45
. . 46
. . 47
48-49
. . 50
. . 51
. . 52
. . 53
. . 54
. . 55
56-57
. . 58
. . 59
60-61
. . 62
. . 63
64-65
66-67
. . 68
. . 69
n
n
RHC Series . . . . . . . . . . . . . . . . . .
HZ Series . . . . . . . . . . . . . . . . . . .
RX Series . . . . . . . . . . . . . . . . . . .
RFX-EX Series. . . . . . . . . . . . . . . .
RFX-CS Series. . . . . . . . . . . . . . . .
LDX-EXP-P Series . . . . . . . . . . . . .
LDX-EXP Series. . . . . . . . . . . . . . .
LDX-EXP-S Series . . . . . . . . . . . . .
RT Series . . . . . . . . . . . . . . . . . . .
Special Wording. . . . . . . . . . . . . . .
LED Retrofit Kits . . . . . . . . . . . . . .
Pendant Kit. . . . . . . . . . . . . . . . . .
Wire Guards & Mounting Shelves . .
EZ2™ Canopy. . . . . . . . . . . . . . . . .
Glossary . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
70-71
72-73
74-75
76-77
78-79
80-81
82-83
84-85
. . 86
. . 87
88-90
. . 91
92-93
. . 94
. . 95
n
n
n
n
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . 99
100-101
102-103
. . . 104
. . . 105
. . . 106
. . . 107
108-109
110-111
112-113
114-115
. . . 116
. . . 117
118-119
120-121
122-123
. . . 124
. . . 125
126-127
128-129
130-131
132-133
134-135
. . . 136
. . . 137
. . . 138
. . . 139
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . 143
144-145
146-147
. . . 148
. . . 149
. . . 150
. . . 151
. . . 152
remote fixtures
n
n
n
Table of contents. . . . .
Overview. . . . . . . . . . .
Cadilite® Series . . . . . .
RCSR Series . . . . . . . .
RL40M Series . . . . . . .
Invislite™ Series. . . . . .
Mini Invislite™ Series . .
Guardian™ Series. . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . 153
. . . 154
. . . 155
. . . 156
. . . 157
. . . 158
. . . 159
160-161
. . . 162
. . . 163
. . . 164
. . . 165
166-168
. . . 169
central systems
Battery Units
Table of contents. . . . . . . . .
Overview. . . . . . . . . . . . . . .
Cadilite® Series . . . . . . . . . .
Invislite™ Series. . . . . . . . . .
Mini Invisilite™ Series. . . . . .
Avenger™ Series. . . . . . . . . .
Legend™ Recessed Series . .
Legend™ Deco Cab Series . .
LDX-VQ Series. . . . . . . . . . .
LDX-T Series. . . . . . . . . . . .
LDX-TS Series. . . . . . . . . . .
Escape™ C29 Series. . . . . . .
RCSB Series . . . . . . . . . . . .
LDXC Series . . . . . . . . . . . .
LDXA Series . . . . . . . . . . . .
Ultima™ Series. . . . . . . . . . .
LES18P Series. . . . . . . . . . .
B-29 Series. . . . . . . . . . . . .
LDX Series. . . . . . . . . . . . . .
TUF-NM Series . . . . . . . . . .
LDX-HZ Series. . . . . . . . . . .
LDX-I Series . . . . . . . . . . . .
LDX-NX Series. . . . . . . . . . .
SIPR Series. . . . . . . . . . . . .
IPR Series. . . . . . . . . . . . . .
RIB/FEB Series . . . . . . . . . .
Glossary . . . . . . . . . . . . . . .
RF105 Series. . . . . . .
RT/RQ/RM Series. . . . .
LT/LQ/LS Series. . . . . .
Legend™ Series . . . . . .
RLR Legend™ Series . .
VQ Series . . . . . . . . . .
RL25 Series. . . . . . . . .
TUF-NM Series . . . . . .
WT Series . . . . . . . . . .
WSR & WHR Series. . .
NMHZ Series. . . . . . . .
RFX Series . . . . . . . . .
Lamp Chart. . . . . . . . .
Glossary . . . . . . . . . . .
n
Table of contents. . . . . . . . . . . . . . . . . 173
What is RL-5. . . . . . . . . . . . . . . . . 174-175
IPS Single Phase Series. . . . . . . . . 176-177
IPS Three Phase Series . . . . . . . . . 178-179
Systems Options . . . . . . . . . . . . . . . . . 180
User Interface & Display Functions. . . . 181
Mini Inverter Series . . . . . . . . . . . . 182-183
RL4 Series. . . . . . . . . . . . . . . . . . . 184-185
RL Series. . . . . . . . . . . . . . . . . . . 186-188
Central System Request Data Form. . . . 189
options & Accessories
n
Table of contents. . . . . . . . . . . . . .
LED Retrofit Kits . . . . . . . . . . . . . .
LED RLB BULB Series. . . . . . . . . .
Pendant Kits . . . . . . . . . . . . . . . . .
EZ2™ Canopy. . . . . . . . . . . . . . . .
RIB/FEB Series . . . . . . . . . . . . . . .
Wire Guards & Mounting Shelves. .
Nexus® Management System . . . . .
ZCP Series . . . . . . . . . . . . . . . . . .
. . . 193
194-195
. . . 196
. . . 197
. . . 198
. . . 199
200-201
. . . 202
. . . 203
technical information
Table of contents. . . . . . . . . . . . . . . . . 207
Wire Size Guide. . . . . . . . . . . . . . . . . . 208
Battery Unit Capacity Chart . . . . . . . . . 209
Electrical Code . . . . . . . . . . . . . . . 210-212
Building Code . . . . . . . . . . . . . . . . 213-217
Fire Code & Generator Room Code. . . . 218
Limited Warranty. . . . . . . . . . . . . . . . . 219
Product Index . . . . . . . . . . . . . . . . . . . 220
n = new product
company
profile
Fuelled by the creativity, innovation and commitment of every employee, the Thomas & Betts facility is a centre of excellence in emergency
lighting.
Unique North American Thomas & Betts
Manufacturing Facility
Vertically-integrated manufacturing and production capabilities in
North America give Thomas & Betts complete control over lead time,
service, and quality down to the smallest detail. We produce exactly
what we need when we need it, without waiting for large production
runs or overseas shipping. With everything under one roof, we can
ensure that our stringent quality standards are met at every step in
the process from design to production to order fulfillment.
Innovative
The in-house research and development team of highly skilled
professional electrical and mechanical engineers, designers,
and technicians at Thomas & Betts includes specialists with over
twenty-five years of experience in the emergency lighting industry.
This multi-disciplinary group uses advanced technology in all
specialties from mechanical design to operating system software, RF
and power electronic design, lighting design, and LED drivers to continuously create innovative emergency lighting solutions. Comprehensive engineering services are provided to meet special requests from
customers for unique applications. Quality and safety are designed
into each product at conception, and customized testing equipment
is created to ensure that each unit meets codes and conforms to
internal quality control standards including ease of installation and
reliability over time.
2
company
profile
Frequent investments in new equipment improve lead time and enforce the high quality and reliability standards of Thomas & Betts.
The new AOI (automated optical inspection) machine added to the printed circuit board operation in 2012 is one of the first of its
kind in use in North America.
Reliable
Technologically advanced printed circuit board production lines at the Thomas & Betts manufacturing facility produce
thousands of circuit boards daily. Skilled production personnel are trained according to IPC standards, and use
board traceability and tracking software to ensure quality. Universal SMT (surface mount technology) boards and
TH (through-hole) insertion boards are produced in house on multiple lines. Every station is ESD (electro-static
discharge) protected to eliminate static hazards, and our ROHS-compliant wave soldering machine meets lead-free
criteria. Automatic insertion equipment and automatic silicone coating application ensure high productivity and
quality. Highly efficient electro-mechanical assembly lines are optimized for low volume, high mix production runs
with thousands of final assemblies produced each day. Customizations such as specific punching, exact wording,
and color matching can be completed quickly using our in-house machine shop and painting capabilities. All
orders undergo functional testing and quality inspection, with high-voltage, high-amperage power outage simulations
available to test all central power systems for each customer’s specific requirements. Specialized facilities include
a dark room for color contrast measurement; temperature and humidity controlled environments; wall, ceiling and
suspended ceiling installation simulations; and cycle testing automation.
Efficient
Large inventories are ready to ship from warehouses across the country
for fast delivery. To reduce the carbon footprint and minimize the environmental impact of operations, a Sustainable Development policy is in
effect at the Thomas & Betts manufacturing facilities. Through a series
of initiatives, reductions in usage of water, water bottles, electricity and
natural gas, packaging, and pallets have already been realized. Forward-looking initiatives include reductions in paper, further recycling
of pallets, and implementation of an eco-delivery schedule.
The Thomas & Betts manufacturing facility has been ISO 9001 compliant since 2001.
3
MR16 LED
EMERGENCY
LIGHTING
MR16 LED Illumination
With the remarkable technology development in the last decade, the light-emitting diode (LED) is becoming
the preferred solution in low- and medium-power lighting applications. The emergency lighting industry is
no exception: today virtually every new product introduced to market includes “white” LEDs for emergency
illumination. Extremely efficient and long-lasting, LED lamps become the natural alternative to incandescent
lamps due to three main advantages:
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 - 30 lumen per watt of the best halogen lamp.
• = operational life: 30,000+ hours, equivalent to a lifetime warranty in emergency lighting.
• = lower lamp temperature (80 - 120°C) is a huge benefit for lighting in hazardous locations.
200 to 220 Lumen 4W MR16 LED
Leading the technology trend, Ready-Lite® offers a complete series of 4W MR16 LED lamps available for all the
standard battery voltages: 6V, 12V, 24V and 120V. With up to 30,000 hours of operational life and a luminous
flux of typically 220 lumens, they are available with most emergency heads designed to hold an MR16 lamp
and meet the majority of illumination specifications. For example: one pair of LED emergency heads installed
at a height of 7.5ft, illuminates a 6ft by 40ft path of egress. Compared to halogen lamps (16-20W), these 4W
MR16 LED lamps illuminate the same area of egress during an emergency situation by using 75% less power.
This has a direct impact on the battery size, reducing the back-up capacity needs by 75%. Consequently,
it also reduces the total cost of the application, with the use of smaller battery capacity units, the possibility
of using fewer fixtures due to superior illumination, thus also reducing electrical wiring, and it reduces the
environmental footprint.
MR16 LED lamp Benefits
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent lighting
performance to a much higher watt halogen MR16 lamp.
• Reduces required battery capacity by 75%, providing necessary illumination
with fewer remote heads and battery units for project cost savings.
• Small profile, compact white lighting is ideal for architectural applications.
• Vibration-resistant LED stands up to industrial environments.
• Ideal for indoor and outdoor use.
340-Lumen 5W MR16 LED
Keeping pace with technology, in 2012 we introduced a 12V-5W MR16 LED lamp. With a typical luminous
flux of 340 lumens, this lamp has the same lighting performance as a 20W high-output halogen MR16. A twin
emergency head installed at a height of 7.5ft illuminates more than a 70ft path of egress.
1FC
40’
ave
rag
e
1FC
7.5’
70’
ave
rag
e
7.5’
6’
6’
540-Lumen 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp, which offer typical luminous flux of 510 lumens.
Like the lower wattage MR16 LED lamps, this new lamp is specially designed for emergency lighting. It offers
the same lighting preformance as the 35W MR16. A twin emergency head installed at a height of 7.5’ illuminates approximately 100’ path of egress.
1FC
100’
ave
rag
e
7.5’
6’
4
MR16 LED
EMERGENCY
LIGHTING
Case Study: Fewer MR16 LED units required
Emergency lighting units with MR16 LED lamps provide the same illumination at floor level using significantly
fewer units.
• Reduced Installation Costs, due to reduced product and labour requirements.
• Reduced Energy Costs, keeping fewer batteries charged at full capacity to be ready to respond to an
emergency situation at any time.
• Reduced Maintenance and Testing Costs, with fewer units to maintain and test in the Emergency Lighting
System.
• Reduced Lamp Replacement Costs. LED lamps have a 30,000+ hour lamp life compared to only a few
hundred hours typical with incandescent lamps.
• Reduced Environmental Impact, less product materials, less batteries, less transportation, less packaging,
less labour, less waste.
Compare
Where the building code requires an average of 1 foot-candle and a minimum of 0.1 foot-candle at floor level
along the path of egress on a 150’ x 9’ x 9’ corridor with an egress door at one end, a 150’ x 6’ path of egress,
and a 7.5’ unit mounting height.
Standard wedge-base 9W Incandescent Lamp
4W MR16 LED lamps
Standard Emergency Lighting Units with 9W wedge-base incandescent lamps
Same Standard Emergency Lighting Units with 4W MR16 LED Lamps
LAMP SUFFIX
5W MR16 LED lamp
LD9
VOLTAGE
12
WATTAGE
5
WATTAGE
LUMENS
REPLACEMENT #
6
4
200
580.0097-RL
LD7
12
4
220
580.0093-RL
LD13
24
4
220
580.0098-RL
new! 6W MR16 LED lamps
Same Standard Emergency Lighting Units with 5W MR16 LED Lamps
LAMP SUFFIX
VOLTAGE
LD1
LUMENS
340
Same Standard Emergency Lighting Units with 6W MR16 LED Lamps
REPLACEMENT #
LAMP SUFFIX
580.0104-RL
LD10
5
VOLTAGE
12
WATTAGE
6
LUMENS
540
REPLACEMENT #
580.0106-RL
Are you prepared for a safety inspection?
Nexus®
System
Building & Life Safety Codes oblige building owners/managers to ensure the safe evacuation of a building in
the event of an emergency. In the interest of public safety, building owners/managers must meet the outlined
requirements for exit signs and emergency lighting equipment, including the following:
• Conduct a discharge test every month.
• Conduct functional tests annually.
• Keep a log book of maintenance information.
Complying with these requirements can be labour intensive and costly, especially in large buildings where
testing every emergency light requires many man-hours.
Disrupting the power supply during lengthy inspections can also put public safety at risk.
Manage Testing with Nexus ® to Save Time and Costs
Nexus® is a real-time monitoring system that manages the status of your entire Emergency Lighting and Exit
Sign system from a central control unit. Nexus® runs diagnostics, performs required monthly and annual
functional tests, generates maintenance logs and runs compliance reports.
Available in wired or wireless (RF) versions, Nexus® installations often pay for themselves in less than two years.
In addition to operational savings, Nexus® helps increase system reliability and performance and reduces the
risk of failed inspections. One building or a group of properties under the same management can be monitored
with Nexus®.
Maximize System Availability
By allowing maintenance personnel to easily maintain and monitor the emergency lighting system without
having to manually check each unit, Nexus® reduces the hours required to disrupt the power supply for
inspections. With Nexus®, monthly tests and reports on the status of all emergency lights and exit signs can
be done individually, in groups, or together.
Advantages of the Nexus® system include saving labour; maximizing system availability by testing units in groups
and stages rather than setting all units in recovery mode; and the convenience of self-monitoring. Nexus®
indicates the location of a faulty unit and reports it instantly without requiring a manual search.
Update Status Instantly
Nexus® passes messages both to and from the emergency units to instruct the units to perform all mandatory
testing by communicating between the emergency units and a centrally located controller.
Nexus® is a proven system supported by a 5-year warranty, and can contribute to LEED certification and
support green building initiatives.
6
Small System Example
In a system of fewer than 100 units it is most likely that the only hardware required, other than the emergency
units themselves, is a controller. All communication would occur wirelessly and installation would not vary greatly
from a non-monitored system. Once the units are in place, the system will establish the mesh network. The
building itself could be quite large as each unit only needs to be able to communicate with its close neighbours
and does not need to communicate directly with the controller.
Large System Example
The Nexus® RF system has been designed to be extremely flexible and provides for a range of system
options. Each large site will need to be assessed for the best system solution with the assistance of
Thomas & Betts technical staff.
The basic Nexus® RF system is designed to run on an Ethernet network which is present in most modern
buildings; however, through a range of interface cards the backbone of the network could be WLAN.
As with the small system example, site performance will be optimized through the careful selection and
placement of Area Controller Routers and the Area Controller to form efficient clusters. Building layout and
materials will also play some role in determining the best solution to deliver a highly effective means of testing
and maintenance requirements.
7
Nexus®
System
Electrical exit signs (connected to a
source of power) differ from battery
units as they shall be illuminated at all
times during normal AC operation, and
not only upon loss of AC power.
overview
RDE
P. 12-13
P.14-15
RXL33F
legend™CS2000
P. 21
cs5000
p. 33
rn
rhc
p. 70-71
CXL3000B12
designer cx4000
cs4000
cx4000bil
cx5
cx5000R
P. 23
P. 28
n
R-SN
p. 47
p. 62
CXL3000BIL
p. 42
sm-nextn
RCS
CSL3000
rs
p. 41
p. 48-49
n
RCSC
p. 55
tuf
rac
n
n
CNESTU
p. 44
cnextn/cnsxtn
ld12-E
ld12-S
P. 51
p. 52
ultima™
cs9000N
cx9000bil
p. 50
n
p. 56-57
n
p. 64-65
rnc
RT SERIES
ez2™
glossary
p. 94
RA
P. 31
P. 26
p. 43
LDX-EXP-S
p. 92-93
legend™CX2000
P. 25
nextn
p. 74-75
wire guards
ULTD
P. 20
p. 38-39
p. 72-73
p. 84-85
cx7000
RSL33
P. 19
p. 36-37
n
ldx-exp
P.30
RXL33
p. 35
p. 63
hz
n
P. 24
P. 29
n
p. 82-83
RAE
P. 18
P. 34
sm-cs5000
RXL3
P. 16-17
P. 22
P. 27
p. 54
n
rx-ex
p. 86
p. 58
n-tuf
p. 45
rp
n
p. 32
sm-cx5000
p. 40
rsc
p. 46
n
ultima™
p. 53
ld6-if
p. 59
rh
cx5000
p. 60-61
p. 66-67
n
p. 76-77
p. 78-79
rfx-cs
ldx-exp-P
special wording
led retrofit
pendant kit
n
rfx-EX
p. 87
p. 68
p. 88-90
p. 95
n = new product
11
n
tufhz
n
p. 69
p. 80-81
p. 91
n
table of
contents
exit & pictogram
signs
overview
Exit & pictogram Signs
signs, incorporate radioactive materials such as tritium gas as a light
source.Their brightness level is very low, that is 2-3% of the minimum
level required for an electrical sign. However, they are safer and easier
to install in hazardous/explosion-proof environments such as coal
mines, natural gas installations, etc. As these signs are not electrical
signs, they are not subject to CSA standards such as C22.2 No. 141.
Electrical Signs (connected to a source of power) differ from battery
units in that they shall be illuminated at all times during normal AC
operation, and not only upon loss of AC power. This has a direct impact
on the admissible energy consumption referenced in government
regulations (National Resources Canada NRCan, CSA C22.2 No.
141), which is a maximum of 5W per legend single or double face.
A legend is defined as a single word, either “SORTIE” or “EXIT”or
“PICTOGRAM” There are also bilingual Exit Signs with: “SORTIE EXIT”
or “EXIT SORTIE”, quite common in applications such as airports or
federal buildings. A bilingual Exit Sign is acceptable up to a maximum
of 10W. The legend must also meet visibility standards including:
dimensions, average brightness, uniformity, background contrast
ratio. The most popular light source is based upon solid state LED
technology, which is capable of meeting both lumen output and energy
efficiency requirements.
COMBINATION UNITS
A well established fixture type, the combination unit or “combo”,
includes both a small battery-powered Emergency Lighting unit and
an AC/DC Sign. An economical and easy to install alternative (installs
to a single electrical box), the combo offers both a Sign indicating
the direction of egress as well as emergency lighting on the path of
egress.
EXPLOSION-PROOF ENVIRONMENT SignS
Does CSA C860 standard apply to all Signs, and in all applications?
Actually, there are no exceptions. Compliance is required in all cases,
even though the solution may be hard to find. For example, equipment
for use in hazardous locations, such as areas classified under Class
I, Division 1 (or Class I, Zones 0 and 1), defined as locations where
flammable gases, vapors or liquids are present frequently or under
normal operating conditions.
Back-lit and Edge-Lit Exit Signs
Two different methods are used to illuminate the legend. The most
common is found in back-lit signs, which use a light source located
behind the legend, illuminated through a diffuser panel. The other
method uses a clear, white or mirrored plastic (acrylic) face panel
on which the legend is etched or silkscreened or a film into a clear
panel. The light source is installed in the top portion of the panel.
Light is transmitted from the top edge of the panel, which is where
the “Edge-Lit” Sign gets its name from. In general, back-lit Signs
are more economical and provide more uniform illumination of the
legend. On the other hand, acrylic Edge-Lit Signs are considered more
high-end, elegant fixtures.
Required luminaires are designed specifically to meet CSA standards
for explosion-proof equipment. The heavy-duty luminaires are rated
for lamp wattages ranging from 50-250W. Constructed of die-cast
aluminum, the units feature a resistant prismatic glass globe
providing hemispherical light distribution. Until now, because of these
characteristics, traditional Signs were using 15-25W incandescent
lamps in order to provide sufficient illumination of the legend.
Conversely, an LED Sign is typically rectangular and relatively thin
(4-8cm) with an axial light source consisting of a line of LEDs to
provide indirect illumination of the legend through multiple reflections.
So, how is it possible to develop an LED Sign that meets NRCan/C22.2
No. 141 using a bulky heavy-duty luminaire dedicated to hazardous
locations Class I, Division 1?
BATTERY, REMOTE, AC AND OTHER POWER SOURCES
Three types of fixtures are available for emergency lighting applications.
The first type is the Self-powered Sign, with a rechargeable battery
for emergency mode operation. Next is the Remote Sign, or AC/
DC Sign: in addition to a normal AC power supply, it includes a DC
input (6VDC, 12VDC, etc.) for remote power supplied by from a
separate battery backup. Installation of such Signs requires DC wiring
between both fixtures. Finally, the AC-only Signs are for applications
where emergency power is supplied from an AC Central System.
A variation on Sign design uses photo-luminescent materials for the
legend (letters and/or background). According to the National Building
Code, photo-luminescent Signs must be continuously illuminated by
a dedicated light source connected to an emergency power supply.
The Thomas & Betts R&D group has found a solution and
developed a special LED lamp series that is easy to install in
the lamp base of explosion-proof type luminaires. This special
LED lamp consumes less than 5W in either AC or DC current
of high performance LEDs configured in a unique pattern.
Horizontal distribution is 360 degrees radially and vertical
distribution is directly focused on the sign legend. This innovative
design meets the visibility criteria on standard size legends, while
In addition to electrical Signs, there are power free, self-luminous
12
limiting power consumption to between 3 to 4.7W per Sign.
To validate the design: in-house LED life tests commenced early in
2009, one year ahead of the adoption of the pictogram exit sign by
the National Building Code. Data collected during 45,000 hours (five
years+) of continuous operation indicate that LED light depreciation
is less than 5% of the initial levels in 2009. This enables us to raise
our statistical prediction of our LED life to at least 90,000 hours (10
years) of continuous operation to the L70 level.
LED lamps are dedicated to various voltage ratings: 6V, 12V, 24V or
120V and operate on DC and AC, supplying power to the Sign from
emergency lighting unit equipment or central AC or DC systems.
Lamps are listed/certified CSA C-US to CSA T.I.L. B-69 and UL1993
standards for LED technology based lamps or lamps with integral
ballast. This further reinforces the assurance of performance and
safety of the Signs using these lamps. The new Sign series from
Thomas & Betts includes fixtures designed for installation in all
hazardous location classifications: Class I Divisions 1 and 2, Groups
A, B, C and D; Class II Divisions 1 and 2, Groups E, F, and G; Class
III Divisions 1 and 2. Specifiers specialized in industrial lighting
are now assured that they can specify certified hazardous location
equipment also approved and compliant to NRCan/CSA C22.2 No.
141 standards. The new technology also significantly improves the
maintained light output of the LED by utilizing materials that operate
at lower temperatures than the previous generation of LEDs.
The outstanding test results with the InGaN-YAG technology and
patented LED drivers have allowed Thomas & Betts to manufacture
pictogram signs with maintained lighting performance. By design,
the initial luminance levels of the legend exceed by 50% to 100%
the minimum requirements of standard CSA C22.2 No.141-10. As
a consequence: even after 10 years of continuous use the projected
luminance levels of the pictogram legend will still be compliant with
the CSA standard of visibility.
First in the industry with proven long-life test results, Thomas & Betts
manufactures pictogram exit signs with ten years+ of CSA photometric
compliance.
Following the requirements of the National Building Code, the new
generation of exit signs has replaced the text legend (EXIT, SORTIE)
with a pictogram legend featuring a green running silhouette on a
white illuminated background. As a consequence the legend is now
illuminated by white LEDs, which replace the traditional monochrome
red or green LEDs. Due to different manufacturing technologies
the utilization of white LED has raised awareness about their life
expectancy in continuous operation.
White LEDs are increasingly being used in the lighting industry. Their
operational life is defined by industry standards like LM80, as the time
elapsed until the LED luminous flux decreases to 70% of the initial
value (life definition: L70). Following the minimum requirements of
the LM80 standard, LED manufacturers usually test their products
for 6,000 hours (little longer than 8 months) and then predict the
total operational life based on statistical methods and extrapolation.
To insure the quality and long-life of pictogram signs the design and
engineering team of Thomas & Betts has carefully selected the LED
technology for their products. The LED chip is based on a compound
of three elements: Indium, Gallium and Nitrogen (InGaN) and
generates a mono-chrome light wave of royal-blue color. The white
light emission is obtained by covering the chip with a layer containing
mainly phosphor and three other elements: Yttrium, Aluminum and
Garnet silicate minerals (YAG). The InGaN-YAG technology has an
estimated operational life of minimum 50,000 hours before the light
output decreases to 70% of initial level.
Furthermore, the LEDs are powered by a T&B-patented electronic
circuit for constant direct current (CDC), specially designed to drive
the LEDs for an extended operational life.
13
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Project/Location:
Contractor:
Model No.: Date:
Made in Canada
T ypical specifications
Prepared by:
Supply and install the Ready-Lite RDE Series of Die-Cast pictogram Edge-Lit signs.
Lumacell Model:
When specified for surface mount, the unit shall come standard with a trim plate, trim ring, back box and
canopy made of Die-Cast aluminum with
finish. The trim plate shall have a
profile and allow
for wall- or ceiling-mount installation. The trim ring shall allow for semi-recessed installation in walls or ceilings
with cavity. The canopy shall allow for wall, end, or ceiling mount.
When specified for recessed ceiling-mount, the unit shall come standard with a flat trim plate of Die-Cast
aluminum with
finish, a back box of galvanized steel, and a hardware kit for back box installation
between ceiling joists. The back box shall be provided with conduit knock-outs at the top, back and end.
All Edge-Lit units shall have the trim plate snap and lock in the housing with torsion spring retainers, thereby
eliminating any visible screws or hardware. The legend shall be printed on a clear acrylic panel. The light
source shall be long-life white light-emitting diodes (LED) and shall provide even illumination in normal and
emergency operation. The Edge-Lit sign shall operate with universal 2-wire AC input voltage of 120 to 347VAC
at less than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC at less than 2.5W. The Edge-Lit sign
in a Self-powered configuration shall use a sealed Nickel-Cadmium battery of 2.4V nominal voltage and shall
stay illuminated during emergency operation for at least two hours upon AC failure.
When specified, the Self-powered unit shall include non-audible auto-test functions, managed by a microcontroller: it shall execute automatic tests for 5 minutes every 30 days, 30 minutes every 60 days and two
hours annually. When a fault is detected a red flashing LED shall identify the failure type: battery, charger
circuitry, or LED lamps.
The Edge-Lit sign shall be listed CSA 22.2 No.141-10.
The equipment shall be Ready-Lite ® Model:
.
®
RDE Series
Die-Cast Aluminum
Pictogram Exit Edge-Lit Sign
Features
• Self-powered models provide minimum
120 minutes of emergency lighting
• Die-Cast aluminum construction
• Modular design offers great choice of
architectural profiles
• Universal Die-Cast back-box for surface
or semi-recessed mounting on ceilings
or walls
• LED strip module can be rotated in the
unit for either wall or ceiling mount
• Flat Die-Cast trim plate and galvanized
steel back-box for recessed ceiling
mount
• Clear acrylic panel with pictogram
legend
• White LED light source
• Universal AC input: two-wire 120 to
347VAC; universal DC input: two-wire
6 to 24VDC
• Energy efficient – consumes less than
2.5W in AC and DC-remote modes
• Meets or exceeds CSA 22.2 No.141-10
Power consumption
Model
AC Specs
DC Specs
AC-only
120 to 347VAC
less than 2.5W
-
-
AC/DC standard
120 to 347VAC
less than 2.5W
6 to 24VDC
less than 2.5W
self-powered
120 to 347VAC
less than 3.5W
nickel-cadmium battery
minimum 2 hours
self-powered diagnostic
120/347VAC
less than 3.5W
nickel-cadmium battery
minimum 2 hours
14
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
4” [10.0 cm]
2-1/2” [6.4 cm]
8” [20.3 cm]
6-7/8” [17.3 cm]
11-3/4” [29.8 cm]
9-3/4” [24.7 cm]
6-1/4” [15.7 cm]
1-1/8” [2.9 cm]
4-5/8” [11.6 cm]
11-1/2” [29.2 cm]
16-3/4” [42.7 cm]
16” [40.8 cm]
2-7/8” [7.4 cm]
2-7/8” [7.4 cm]
4” [10.0 cm]
11-5/8” [29.6 cm]
4-5/8” [11.6 cm]
3-1/4”
[8.3 cm]
2-1/2” [6.4 cm]
Circular trim
RDE Series
Die-Cast Aluminum
Pictogram Exit Edge-Lit Sign
13” [32.9 cm]
8” [20.3 cm]
6-7/8” [17.3 cm]
11-3/4” [29.8 cm]
4” [10.0 cm]
2-1/2” [6.4 cm]
4-5/8” [11.6 cm]
11-1/2” [29.2 cm]
16-3/4” [42.7 cm]
16” [40.8 cm]
6-1/4” [15.7 cm]
4” [10.0 cm]
1-1/8” [2.9 cm]
2-7/8” [7.4 cm]
2-7/8” [7.4 cm]
9-3/4” [24.7 cm]
11-5/8” [29.6 cm]
4-5/8” [11.6 cm]
3-1/4” [8.3 cm]
2-1/2” [6.4 cm]
angular trim
13” [32.9 cm]
Flat trim
3-7/8” [9.9 cm]
3-1/4” [8.3 cm]
3-7/8” [9.9 cm]
7” [17.8 cm]
6-7/8” [17.4 cm]
15” [38.1 cm]
13” [32.9 cm]
ordering information
Series
RDE= d
ie-cast edge-lit
pictogram exit sign
faces/arrow
1= single face, no arrows
L= arrow left, single face
R= arrow right, single face
A= double face, arrow left or right
housing colour
A= brushed
aluminum
B= black
C= chrome
P= polished brass
W= factory white
Z= bronze
Trim
A= angular
C= circular
F= flat
(fully recessed)
VOLTAGE
AC= AC only, 120 to 347VAC
DC= 120 to 347VAC, 6 to 24VDC
U48= 120 to 347VAC, 48VDC
SP= self-powered, 120 to 347VAC
SD= self-powered diagnostic (non-audible),
120/347VAC
SD2= self-powered diagnostic (non-audible),
120/277VAC
NEX= Nexus® system interface*
NEXRF= wireless Nexus® system interface*
*Not all options available with NEXUS® System.
Please consult your sales representative
EXAMPLE: RDE1ACSP
Unlike EXIT signs, the pictogram sign is not available in double arrow configurations.
15
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RXL3 Series
Die-Cast Edge-Lit Exit Sign
Features
• Die-Cast aluminum construction
• Modular design for universal mounting
• Trim plate choices: angular or circular
for universal mounting and flat
(recessed ceiling)
• Component-free back-box housing and
canopy can be installed in advance,
like a regular junction box.
• LED strip module can be rotated in the
unit for either wall or ceiling mount
• Also available with white LEDs for
custom-design, and special wording
signs (ask our sales representatives)
• U-shaped clear acrylic panel with
laser-etched contour for legend letters
• Long-life LED light source; red LEDs of
ALINGAP technology
• Bi-colour LED pilot light allows visual
diagnostic without need to open the
unit (self-test and diagnostic option)
• Two-wire universal AC input: 120 to
347VAC 50/60Hz
• Sealed, maintenance-free
Nickel-Cadmium battery
• Meets or exceeds CSA 22.2 No.141-10
Supply and install the Ready-Lite® RXL3 Series of Die-Cast Edge-Lit Exit Signs.
The unit specified for universal mounting shall come standard with a trim plate, trim ring, back box and canopy
all made of die-cast aluminum with _____ finish. The trim plate shall have a _____ profile and allow for
wall- or ceiling-mount installation. The trim ring shall allow for recessed installation in walls or ceilings with
cavity. The canopy shall allow for wall, end, or ceiling mount. The back box shall be provided with conduit
knock-outs at the top, back and end.
The unit specified for recessed ceiling shall come standard with a flat trim plate of Die-Cast aluminum with
_____ finish, and a back box of 20-gauge galvanized steel. The back box shall be provided with conduit
knock-outs at the top, back and end. All models shall be provided with a hardware kit including two 27”
adjustable bar hangers for back box recessed installation.
The unit shall have the trim plate snap and lock in the housing with torsion spring retainers, thereby eliminating
any visible screws or hardware. The legend shall be printed on a clear acrylic panel. The panel shall have
a U-shape and the legend shall have precision etched 6” high and 3/4” stroke red letters with laser-edged
contour and with a white, clear or mirror background. The light source shall be long-life light-emitting diodes
(LED) and shall provide even illumination in normal and emergency operation. Red LED technology shall be
ALINGAP. The unit shall operate with two-wire universal AC input voltage from 120 to 347VAC and two-wire
universal DC input from 6 to 24VDC, each input at less than 1.4W.
The Edge-Lit sign in a Self-powered configuration shall use a sealed Nickel-Cadmium battery and shall stay
illuminated during emergency operation for at least 90 minutes upon AC failure.
The Self-powered unit with self-test and silent diagnostic functions shall be managed by a micro-controller:
it shall execute automatic tests for one minute every 30 days, 30 minutes every 60 days and 90 minutes
annually. A diagnostic circuit shall continuously monitor the performance of the battery, charger module
and LED lamps. When a fault is detected the pilot light shall change colour from green to red and flash with
a specific code. The red light is steady-on in case of battery disconnect; it will flash with one blink for battery
failure, two blinks for charger failure and four blinks for LED lamp failure. A label with the diagnostic legend
shall be visible next to the pilot light.
The Edge-Lit sign shall be certified CSA C22.2 No.141 and CSA-C860.
The Exit Sign shall be Ready-Lite® Model:
.
Power consumption
Model
AC Specs
DC Specs
AC-only
120 to 347VAC
less than 1.4W
AC/DC - remote
120 to 347VAC
less than 1.4W
6 to 24VDC
less than 1.4W
self-powered
120 to 347VAC
less than 2.3W
nickel-cadmium battery
minimum 90 minutes
self-powered diagnostic
120/347VAC
less than 2.3W
nickel-cadmium battery
minimum 90 minutes
16
-
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
Die-Cast Edge-Lit
4” [10.0 cm]
2-1/2” [6.4 cm]
8-5/8” [21.9 cm]
7-1/2” [19.0 cm]
12-3/8” [31.5 cm]
13” [32.9 cm]
4-5/8” [11.6 cm]
12-1/8” [30.9 cm]
16-3/4” [42.7 cm]
16” [40.8 cm]
6-1/4” [15.7 cm]
4” [10.0 cm]
10-5/8” [27.1 cm]
12-1/4” [31.3 cm]
4-5/8” [11.6 cm]
2-1/2” [6.4 cm]
1-1/8” [2.9 cm]
2-7/8” [7.4 cm]
2-7/8” [7.4 cm]
3-1/4” [8.3 cm]
RXL3 Series
Die-Cast Edge-Lit Exit Sign
Die-Cast Recessed Edge-Lit
3-7/8” [9.9 cm]
3-1/4” [8.3 cm]
3-7/8” [19.9 cm]
7-1/2” [19 cm]
7-5/8” [19.4 cm]
15” [38.1 cm]
13” [32.9 cm]
ordering information
Series
RXL3
housing
Colour
Faces
1= s ingle
face
2= d
ouble
face
BK= black
BA= brushed
aluminum
BR= bronze
CH= chrome
PB= polished brass
WH= factory white
Trim Option
A= angular, universal
mount
C= circular, universal
mount
F= flat trim, ceiling
mount, fully recessed
legend
colour
R= red
G= green
Background
colour
C= c lear single face
M= mirror
W= white
Chevrons
N= no chevrons
L= chevron left
R= chevron right
A= one chevron,
double face
D= double chevron
voltage
AC= AC only, 120 to 347VAC
DC= 120 to 347VAC, 6 to 24VDC
SP= self-powered, 120 to 347VAC
SD= self-powered diagnostic
(non-audible), 120/347VAC*
SD2= s elf-powered diagnostic
(non-audible), 120/277VAC*
NEX= N
EXUS® system interface**
NEXRF= wireless NEXUS® system
interface**
*Self-powered (90 mins. time base)
**Not all options available with NEXUS®
System. Please consult your sales
representative
EXAMPLE: RXL31BAARCNAC
17
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RAE Series
Aluminum Slim Edge-Lit
Pictogram Exit Sign
Supply and install the Ready-Lite® RAE Series slim-profile pictogram Edge-Lit Exit Sign. The unit shall
operate with universal 2-wire AC input voltage of 120 to 347VAC at less than 3W and universal 2-wire
DC input voltage from 6 to 24VDC at less than 2.5W. The housing assembly shall be constructed of
extruded aluminum with textured finish and
colour. The canopy shall be of Die-Cast aluminum
and allow for wall, end, or ceiling mount. The legend shall be printed on a pure-acrylic panel. The light
source shall be long-life white light-emitting diodes (LED) and shall provide even illumination in normal and
emergency operation. The pictogram Edge-Lit Exit Sign in a Self-powered configuration shall use a sealed
Nickel-Cadmium battery of 2.4V nominal voltage and shall stay illuminated during emergency operation for
at least two hours upon AC failure.
The pictogram Edge-Lit Exit Sign shall be listed CSA 22.2 No.141-10.
The equipment shall be Ready-Lite® Model:
Dimensions
Dimensions are approximate and subject to change.
12-1/2” [31.9 cm]
9-5/8” [24.4 cm]
10-3/4” [27.3 cm]
10-5/8” [27.0 cm]
< Pictogram
Left from here
Pictogram >
Right from here
4-1/4” [10.7 cm]
12” [30.5 cm]
1-5/8” [4.2 cm]
10-1/8” [25.7 cm]
• Slim-profile extruded aluminum
housing
• Universal surface mounting – wall,
ceiling or end mount
• Click-to-open housing door allows
easy access to the panel and electrical
wiring
• Acrylic panel with pictogram legend
• Long-life white LED light source
• Meets or exceeds CSA.222 No.141-10
• Universal AC input: two-wire 120 to
347VAC; standard DC input: two-wire
6 to 24VDC
• Energy efficient – consumes less than
3W in AC or DC-remote mode
• Self-powered models provide minimum
two hours of emergency lighting
10-5/8” [27.0 cm]
Features
.
Pictogram
straight from
here
Power Consumption
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
less than 3W
-
-
AC/DC standard
120 to 347VAC
less than 3W
6 to 24VDC
less than 2.5W
AC/48VDC
120 to 347VAC
less than 3W
48VDC
2W
AC/120VDC
120 to 347VAC
less than 3W
120VDC
4.7W
two-wire 120V AC/DC
120VAC
less than 3.5W
120VDC
less than 3.5W
self-powered
120 to 347VAC
less than 4W
nickel-cadmium battery
minimum 2 hours
Ordering Information
Series
RAE= extruded aluminum edge-lit pictogram exit sign
FaceS / Arrow
1= single face, no arrow
L= single face left arrow
R= single face right arrow
A= double faces, arrow left or right
housing colour
TA= textured aluminum
OW= off-white
Voltage
AC= 120 to 347VAC only
DC= 120 to 347VAC; 6 to 24VDC
SP= self-powered, 120 to 347VAC*
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
2120= 2 wires 120VAC/VDC
*Self-powered (90 mins. time base)
EXAMPLE: RAE1OWDC
18
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® RXL33 Series LED slim-profile Edge-Lit Exit Sign. The unit shall operate with
universal two-wire AC input voltage from 120VAC to 347VAC at less than 1.5W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 1.5W for single and double face legends.
The housing assembly shall be fabricated of extruded aluminum with a textured finish and
colour.
The canopy shall be of die-cast aluminum and allow for ceiling, wall, or end mount installation. The light
source shall be ten (10) long-life LEDs installed on a PCB strip. Red LED technology shall be ALINGAP. The
acrylic panel shall have a curved contour.
The legend shall have 6” high, 3/4” stroke red letters on a clear background, unless otherwise specified. The
unit shall be equipped with stick-on translucent directional indicators, to be installed in the field as required
by the code. The Exit Sign in a Self-powered configuration shall be equipped with sealed Nickel-Cadmium
batteries and will provide a minimum of 90 minutes of emergency illumination upon AC failure.
The equipment shall be CSA 22.2 No.141-10 approved.
The equipment shall be Ready-Lite® Model:
.
Dimensions
Dimensions are approximate and subject to change.
Wall mount
end mount
12” [30.5 cm]
ceiling mount
4-1/4” [10.7 cm]
1-5/8” [4.2 cm]
12” [30.5 cm]
10-1/2” [26.6 cm]
11-1/4” [28.6 cm]
10-1/8” [25.6 cm]
11-1/8” [28.2 cm]
12-1/2” [31.8 cm]
RXL33 Series
Aluminum Slim
Edge-Lit Exit Sign
Features
• E xtruded aluminum housing
• Die-Cast aluminum E22 canopy
• Universal surface mounting: wall,
ceiling or end mount
• Click-to-open housing door allows easy
access to the panel and electrical wiring
• Acrylic panel with curved contour
• Legend with 6” letters and easy to
add-on directional indicators
• Simple, two-wire universal AC input
(120V to 347Vac 50/60Hz) prevents
installation errors
• Simple, two-wire universal DC input:
6V to 24Vdc
• Energy efficient power consumption:
less than 1.5W in AC or DC mode
• Meets or exceeds CSA 22.2 No.141-10
POwer consumption
Model
AC Specs
DC Specs
AC/DC red
120 to 347VAC
less than 1.5W
6 to 24VDC
AC/DC green
120 to 347VAC
less than 2W
6 to 24VDC
less than 1.5W
less than 1.5W
self-powered red
120 to 347VAC
less than 2.5W
nickel-cadmium battery
min. 90 minutes
self-powered green
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
ordering information
Series/faces
RXL3301= single face
RXL3302= double face
Housing colour
panel colours
TA= textured aluminum
OW= off-white
-RC= red/clear*
-RW= red/white
-RM= red/mirror
-GC= green/clear*
-GM= green/mirror
Other colours available.
*Single face only.
E X A M P L E : R X L 3 3 0 1 TA - R C - A C
19
voltage
-AC= 120 to 347VAC only
-DC= 120 to 347VAC, 6 to 24VDC
-SP= self-powered, 120 to 347VAC
-L120-2W= 120VAC, 120VDC, 2 wires
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
POwer consumption
Model
AC Specs
DC Specs
AC/DC
120 to 347VAC
less than 2W
6 to 24VDC
less than 1.5W
self-powered
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
Dimensions
Dimensions are approximate and subject to change.
Wall mount
end mount
17-7/8” [45.3 cm]
ceiling mount
18-3/8” [46.6 cm]
17-7/8” [45.3 cm]
11” [27.9 cm]
• Extruded aluminum housing
• Slim-Profile cast aluminum canopy
• Universal surface mounting: wall,
ceiling or end mount
• Click-to-open housing door allows easy
access to the panel and electrical wiring
• Acrylic panel with curved contour
• Legend with 6” letters and easy to
add-on directional indicators
• Simple, two-wire universal AC input
(120V to 347VAC 50/60Hz) prevents
installation errors
• Simple, two-wire universal DC input:
6V to 24VDC
• Long-life LED light source of ALINGAP
technology assures low maintenance
costs
• Energy-efficient power consumption:
less than 3W in AC or DC mode
• Self-powered models provide 90
minutes of emergency illumination
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
11-5/8” [29.6 cm]
Features
10-1/2” [26.6 cm]
Aluminum Slim
Edge-Lit “Sortie” Sign
11-1/2” [29.2 cm]
RSL33 Series
Supply and install the Ready-Lite® RSL33 Series LED slim-profile Edge-Lit “Sortie” Sign. The unit shall operate
with universal two-wire AC input voltage from 120VAC to 347VAC at less than 2W and universal two-wire DC
input voltage from 6VDC to 24VDC at less than 1.5W for single and double face legends.
The housing assembly shall be fabricated of extruded aluminum with a textured finish and
colour.
The canopy shall be of Die-Cast aluminum and allow for ceiling, wall, or end mount installation. The light
source shall be fourteen (14) long-life LEDs installed on a PCB strip. Red LED technology shall be ALINGAP.
The acrylic panel shall have a curved contour. The legend shall have 6” high, 3/4” stroke red letters on a clear
background, unless otherwise specified.
The unit shall be equipped with stick-on translucent directional indicators, to be installed in the field
as required by the code. The Exit Sign in a Self-powered configuration shall be equipped with sealed
Nickel-Cadmium batteries and will provide a minimum of 90 minutes of emergency illumination upon
AC failure.
The equipment shall be CSA 22.2 No. 141 approved.
The equipment shall be Ready-Lite® Model:
ordering information
Series
RSL3301= single face
RSL3302= double face
Housing colour
panel colours
TA= textured aluminum
OW= off-white
-RC= red/clear*
-RW= red/white
-RM= red/mirror
Other colours available.
*Single face only.
E X A M P L E : R S L 3 3 0 1 TA - R C - A C
20
voltage
-AC= 120 to 347VAC only
-DC= 120 to 347VAC, 6 to 24VDC
-SP= self-powered, 120 to 347VAC
4-1/4” [10.7 cm]
1-5/8” [4.2 cm]
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
The Ready-Lite® RXL33F Series combines a low-profile modular design with state-of-the-art technology and
ease of installation. Elegantly discreet, these Exit Signs complement interior designs while providing mounting
versatility and energy efficiency.
Supply and install the Ready-Lite® RXL33F Series LED low-profile recessed Edge-Lit Exit Sign. The unit shall
operate with universal two-wire AC input voltage from 120VAC to 347VAC at less than 1.5W and universal
two-wire DC input voltage from 6VDC to 24VDC at less than 1.5W for single and double face legends. The
housing assembly shall be of rugged 20-gauge steel and shall include a bar hanger kit for easy installation. The
trim plate shall be low-profile and manufactured of formed steel with a textured finish and _____ colour. The
light source shall be eight (8) long-life LEDs installed on a PCB strip. Red LED technology shall be ALINGAP.
The whole electrical circuit shall be contained in a plastic housing fixed on the trim plate. The acrylic panel
shall have a curved contour. The legend shall have 6” high, 3/4” stroke red letters on a clear background,
unless otherwise specified. The unit shall be equipped with stick-on translucent directional indicators, to be
installed in the field as required by the Code.
The Exit Sign in a Self-powered configuration shall be equipped with sealed Nickel-Cadmium batteries and
will provide a minimum of 90 minutes of emergency illumination upon AC failure.
The equipment shall be CSA-C860 and NRCAN/C860-01 approved CSA22.2 No. 141-10
The equipment shall be Ready-Lite® Model:
.
Dimensions
Dimensions are approximate and subject to change.
16” [40.6 cm]
4-1/4” [10.8 cm]
17-1/8” [18.1 cm]
3-3/8” [8.5 cm]
3-3/8” [8.5 cm]
7” [17.7 cm]
15-1/8” [38.3 cm]
11-3/4” [29.7 cm]
Power consumption
Model
AC Specs
RXL33F Series
Low-Profile Recessed
Edge-Lit Exit Sign
Features
• Rugged, 20-gauge steel back box
• Equipped with bar hanger kit for easy
installation
• Formed steel flat trim plate
• Choice of finishes: textured aluminum
or off-white
• Acrylic panel with curved contour
provides superior clarity and illumination
• Legend with 6” letters and easy to
add-on directional chevrons
• Choice of legend background: clear,
white or mirror
• Simple, two-wire universal AC input
(120V to 347VAC 50/60Hz) prevents
installation errors
• Simple, two-wire universal DC input:
6V to 24VDC
• Long-life LED light source of ALINGAP
technology assures low maintenance
costs
• Energy-efficient power consumption:
less than 1.5W in AC or DC mode
• Self-powered models provide 90
minutes of emergency illumination
• Meets or exceeds CSA22.2 No. 141-10
DC Specs
AC-only
120 to 347VAC
less than 1.5W
-
AC/DC-remote
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
self-powered
120 to 347VAC
less than 2.5W
nickel-cadmium battery
min. 90 minutes
ordering information
Series / Faces
RXL3301F= single face
RXL3302F= double face
Housing Colour
TA= textured aluminum
OW= off-white
Panel Colours
-RC= red/clear*
-RW= red/white
-RM= red/mirror
-GC= green/clear*
-GM= green/mirror
*Single face only.
E X A M P L E : R X L 3 3 0 1 F TA - R C - D C
21
voltage
-AC= 120 to 347VAC only
-DC= 120 to 347VAC, 6 to 24VDC
-SP= self-powered, 120 to 347VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
POwer consumption
Model
AC Specs
DC Specs
AC/DC red
120 to 347VAC
less than 4.5W
6 to 48VDC
less than 2.5W
self-powered red
120 to 347VAC
less than 5W
nickel-cadmium battery
min. 60 minutes
Dimensions
Dimensions are approximate and subject to change.
8-5/8” [21.9 cm]
4-5/8” [11.6 cm]
2-7/8” [7.4 cm]
4” [10 cm]
2-1/2” [6.4 cm]
12-1/8” [30.9 cm]
23-3/8” [59.4 cm]
22-5/8” [57.5 cm]
3-1/4” [8.3 cm]
11-3/8” [28.9 cm]
12-3/8” [31.5 cm]
• Universal back box designed for
surface or recessed mounting on
ceilings or walls
• Modular retainer clips allow “snap-in”
installation of face panel after
installation of back box
• Acrylic panels with precision-etched
lettering legend
• LED strip design allows for rotation for
either ceiling or wall mounting
• Long-life, energy-efficient ALINGAP
technology LED light source reduces
maintenance and energy costs
• Energy efficient – consumes less than
5W in AC or DC mode
• Meets or exceeds C860 requirements
• Meets or exceeds CSA22.2 No.141-10
6-1/4” [15.7 cm]
Features
4-5/8” [11.6 cm]
Edge-Lit “Sortie” Sign
12-1/4” [31.3 cm]
CSL3000 Series
Supply and install the Ready-Lite® CSL3000 Series LED “SORTIE’’ Exit Sign.
The equipment shall operate with universal two-wire AC input voltage from 120VAC to 347VAC at less than
4.5W and universal two-wire DC input voltage from 6VDC to 48VDC at less than 2.5W for single or double
face legend. The housing assembly shall be fabricated of aluminum and consist of a universal aluminum
back box. The back box shall be provided with conduit knockouts on top, back, and end. The trim plate
shall have a round shape and attach to the housing assembly with two (2) torsion spring retainers, thereby
eliminating all visible screws or hardware. The LED light strip shall be contained within the trim plate. Red
LED technology shall be ALINGAP. The polished acrylic face panel shall have precision etched 6” high, 3/4”
stroke red letters with a white, clear or mirror background. For recessed applications, please contact your
regional sales representative .
The Exit Sign in a Self-powered configuration shall stay illuminated during emergency operation for at least
60 minutes upon AC failure.
The Exit Sign shall be CSA 860 and CSA22.2 No. 141 approved.
The equipment shall be Ready-Lite® Model:
.
19-1/2” [49.7 cm]
CSL3000 Series
2-1/2” [6.4 cm]
2-7/8” [7.4 cm]
18-1/2” [46.8 cm]
CSL3000 Series
REcessed wall mount only
10-5/8” [27.1 cm]
4” [10 cm]
10-5/8” [27.1 cm]
1-1/8” [2.9 cm]
13-7/8” [35.4 cm]
ordering information
Series
CSL3100= single face
CSL3100R= recessed single
face wall mount,
no chevrons
CSL3200= double face
housing colour
Blank= factory white
BA= brushed aluminum
BK= black
panel colours
-RC= red/clear*
-RM= red/mirror
-RW= red/white
*Single face only.
EXAMPLE: CSL3100-RCNADC
22
chevrons
NA= no chevrons
AL= chevron left
AR= chevron right
DA= double chevron
ALR= o ne chevron each side,
double face
voltage
-DC= 120 to 347VAC, 6 to 48VDC
-SP= s elf-powered, 120 to 347VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® CXL3000BIL & CSL3000BIL Series LED Edge-Lit sign. The equipment
shall operate with universal two-wire AC input voltage from 120VAC to 347VAC at less than 8.6W and
universal 2-wires DC input voltage from 6VDC to 48VDC at less than 4.5W for single and double face signs.
The housing assembly shall be fabricated of aluminum and consist of a universal aluminum back box.
The back box shall be provided with conduit knockouts on top and back. The trim plate shall have a round
shape and shall attach to the housing assembly with two (2) torsion spring retainers thereby eliminating all
visible hardware. The LED light strip shall be contained within the trim plate. Red LED technology shall be
ALINGAP. The polished acrylic face panel shall have precision-etched 6” high, 3/4” stroke red letters with a
white, clear or mirror background, with the words EXIT and SORTIE side by side. The Exit Sign in a Self-powered
configuration shall stay illuminated during emergency operation for at least 30 minutes upon AC failure.
The Exit Sign shall be CSA-C860 and CSA22.2 No. 141 approved.
The equipment shall be Ready-Lite® Model:
.
POwer consumption
Model
AC Specs
DC Specs
AC/DC red
120 to 347VAC
less than 8.6W
6 to 48VDC
less than 4.5W
self-powered red
120 to 347VAC
less than 8.6W
nickel-cadmium battery
min. 30 minutes
Dimensions
Dimensions are approximate and subject to change.
4-5/8” [11.6 cm]
7-1/2” [19 cm]
12-1/8” [30.9 cm]
6-1/4” [15.7 cm]
6-1/4” [15.7 cm]
121/8” [30.9 cm]
12-1/8” [30.9 cm]
4-5/8” [11.6 cm]
CSL3000BIL
31-3/8” [79.7 cm]
34-3/8” [87.2 cm]
2-7/8” [7.4 cm]
Bilingual Edge-Lit Sign
FEATURES
• Universal back box designed for
surface or recessed mounting on
ceilings or walls
• Modular retainer clips allow “snap-in”
installation of face panel after
installation of back box
• LED Edge-Lit, acrylic face panels with
precision-etched lettering
• LED strip design allows for rotation for
either ceiling or wall mounting
• Long life, energy-efficient ALINGAP
technology LED light source reduces
maintenance and energy costs
• Energy efficient – consumes less than
8.6W in AC or DC mode
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
4” [10 cm]
2-1/2” [6.4 cm]
2-7/8” [7.4 cm]
31-3/8” [79.7 cm]
34-3/8” [87.2 cm]
4” [10 cm]
2-1/2” [6.4 cm]
8-5/8” [21.9 cm]
7-1/2” [19 cm]
12-1/8” [30.9 cm]
4-5/8” [11.6 cm]
8-5/8” [21.9 cm]
6-1/4” [15.7 cm]
3-1/4” [8.3 cm]
12-1/8” [30.9 cm]
12-1/4” [31.3 cm]
4-5/8” [11.6 cm]
CXL3000BIL
CXL3000BIL &
CSL3000BIL
Series
ordering information
Series
Faces
CXL= exit sortie
CSL= sortie exit
3100= single face
3200= double face
housing
colour
Blank= factory
white
BA= brushed
aluminum
BK= black
panel
colours
RC= red/clear*
RM= red/mirror
RW= red/white
chevrons
NA= no chevrons
AL= chevron left
AR= chevron right
DA= double chevrons
ALR= o ne chevron each
side, double face
*Single face only
EXAMPLE: CXL3100RCNADCBIL
23
voltage
DC= 120 to 347VAC,
6 to 48VDC
SP= s elf-powered,
120 to 347VAC
approval*
options
-BIL
R= r ecessed mount*
*Required field
*Ceiling mount only.
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Dimensions
Dimensions are approximate and subject to change.
16 " [42.7cm]
16-3/4”
[42.7 cm]
[40.8cm] cm]
16”16"[40.8
3
4
4" [10.0cm]
4”
[10 cm]
2 " [6.4cm] [6.4 cm]
2-1/2”
4 " [11.6cm]
4-5/8”
[11.6 cm]
5
8
7
8
3
4
1
8
[36.0cm]
14-1/8”14 "[36
cm]
1
4
17 " [44.9cm]
17-3/4”
[44.9 cm]
1
2
[45.6cm]
18”18"
[45.6
cm]
4" [10.0cm]
4” [10
cm]
16 "[41.2
[41.2cm] cm]
16-1/4”
1
2
1
8
1
4
1 " [2.9cm]
1-1/8”
[2.9 cm]
[15.7cm] cm]
6-1/4”6 " [15.7
1
4
2 " [7.4cm]
2-7/8” [7.4
cm]
2 " [7.4cm]
2-7/8”
[7.4 cm]
7
8
" [8.3cm]cm]
3-1/4”3 [8.3
2 " [6.4cm]
2-1/2” [6.4
cm]
• The Edge-Lit front panels are fabricated
of extruded acrylic, with precision
etched lettering
• Normal AC operation and emergency
DC operation: 120-347VAC and
6-48VDC
• Also available in a Self-powered
configuration
• Long life, energy-efficient ALINGAP
technology LED light source reduces
maintenance and energy costs
• Meets or exceeds C860 requirements
• Meets or exceeds CSA 22.2 No. 141
requirements
5
8
Features
7
8
Bilingual Square Edge-Lit Sign
" [45.4cm] cm]
17-7/8”17 [45.4
4 " [11.6cm]
4-5/8” [11.6
cm]
CXL3000B12 Series
Supply and install the Ready-Lite® CXL3000B12 Series LED Edge-Lit bilingual Exit Sign. The equipment shall
operate with universal two-wire AC input voltage from 120VAC to 347VAC at less than 4W and universal
two-wire DC input voltage from 6VDC to 48VDC at less than 2W for single or double face signs. The housing
assembly shall be fabricated of Die-Cast aluminum and consist of a universal die cast aluminum back box. The
back box shall be provided with conduit knockouts on top and in the back. The trim plate shall have a circular
shape and attach to the housing assembly with two (2) torsion spring retainers thereby eliminating all visible
hardware. The LED light strip shall be contained within the trim plate. Red LED technology shall be ALINGAP.
The polished acrylic face panel shall have precision etched 6” high, 3/4” stroke red letters with a white, clear
or mirror background, with the text ”EXIT” and “SORTIE” positioned one on top of the other. When directional
chevrons are specified, they will be printed next to the word “EXIT”. The Exit Sign specified for recessed
applications will be supplied with a flat trim plate. The bilingual Exit Sign in a Self-powered configuration shall
stay illuminated during emergency operation for at least 30 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141
The equipment shall be Ready-Lite® Model:
.
13 " [35.4cm]
13-7/8”
[35.4 cm]
7
8
POwer consumption
Model
AC Specs
DC Specs
AC/DC red
120 to 347VAC
less than 3W
6 to 48VDC
less than 1.5W
self-powered red
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 30 minutes
ordering information
Series
CXL= exit/sortie
CSL= sortie/exit
Faces
3100= single face
3200= double face
Housing colour
W= factory white
BA= brushed aluminum
BK= black
Voltage
DC= 120 to 347VAC,
6 to 48VDC
SP= self-powered,
120 to 347VAC
chevrons
NA= no chevrons
AL= chevron left
AR= chevron right
DA= double chevron
A= one chevron, each side
double face
panel colours
RC= red/clear*
RW= red/white
RM= red/mirror
*Single face only
EXAMPLE: CXL3100WDCNARCb12
24
approval
B12
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Stylish, built of Die-Cast aluminum, the new ULTD Series offers superior workmanship, versatile mounting
capabilities and economical, long-lasting LED performance. Supply and install the Ready-Lite® ULTD Series Exit
Sign. The frame, face plate(s), back plate and canopy shall be constructed of Die-Cast aluminum of ______
finish and ______ color. No screws are necessary to hold the faceplate(s) or the back plate to the housing.
The unit shall be suitable for installation on wall, end, or ceiling mount. The faceplates shall come standard
with knockout chevrons. The light source shall be light emitting diodes (LEDs). Red LED technology shall be
ALINGAP. The LEDs shall provide illumination in normal and emergency operation and shall be mounted inside
the exit housing, not on the face. An LED-sensitive diffuser shall be mounted in front of the LEDs to provide
the 6” high by ¾” stroke letters with even illumination. The Exit Sign in a Self-powered configuration shall be
equipped with a sealed, maintenance-free Nickel-Cadmium battery. The equipment shall operate with a dualvoltage input of 120/347VAC 60Hz with less than 3.5W of consumption. The equipment shall stay illuminated
at least 90 minutes upon AC failure. The Exit Sign shall be listed to UL924 standard and be approved for use
in damp locations. When specified, the Self-powered model equipped with advanced diagnostic shall self-test
by simulating a power failure for one minute every 30 days, 30 minutes every 60 days and 90 minutes every
360 days. A diagnostic circuit shall continuously monitor the performance of the battery, charger module and
LED lamps. Upon failure detection the system shall display the error on the AC pilot lamp, which will change
color from green to red and will flash with a specific code. The red light shall be steady-on in case of “Battery
Disconnect”; it shall flash with one blink for “Battery failure”, two blinks for “Charger failure” and four blinks
for “LED lamp failure”. A label with the diagnostic legend shall be visible next to the pilot light.
.
The Exit Sign shall be Ready-Lite® Model:
Dimensions
Dimensions are approximate and subject to change.
5-1/2” [13.9 cm]
9-1/8” [23.1 cm]
1-7/8” [4.7 cm]
8-5/8” [21.9 cm]
4-3/8” [11.1 cm]
ULTD Series
Die-Cast LED Exit Sign
Features
• Housing of Die-Cast aluminum in a
variety of finishes
• Slim-line canopy for top and end
mounting
• Universal mounting or wall, end, or
ceiling mounting
• Universal, field-selectable knock-out
chevrons
• Long-life LED light source. Red LED’s of
ALINGAP technology
• Dual voltage input: 120/347VAC120/277 VAC, 60Hz options
• Low power consumption: less than
3.5W in any configuration
• Self-powered models with sealed
maintenance-free Nickel-Cadmium
batteries
• Meets or exceeds CSA 22.2 No. 141
requirements
• Five-year full warranty
12-7/8” [32.7 cm]
Wire guards
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Power consumption
Model
AC Specs
DC SPECS
AC only
120/347VAC
less than 3W
-
-
AC/DC remote
120/347VAC
less than 3W
6 to 48VDC
less than 1.5W
self-powered
120/347VAC
less than 3.5W
nickel-cadmium battery
minimum 90 minutes
self-powered with diagnostic
120/347VAC
less than 3W
nickel-cadmium battery
minimum 90 minutes
ordering information
Series
ULTD= LED
die-cast
housing/faceplate Colours
BA= black/ brushed aluminum
A= brushed aluminum
WA= white/ brushed aluminum
W= factory white
B= black
Unit type
AC= AC only
AC2C1= dual AC circuit (2 x 120V)
UD= 120/277 or 120/347VAC & 6 to 48VDC
SDN= self-powered diagnostic NiCad,
120/347VAC
SPN= self-powered NiCad, 120/347VAC
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
*Not all options available with NEXUS® System.
Please consult your sales representative
E xample : U LT D A A C 2 R 1
25
Voltage
Legend colour
Blank= dual AC
circuit
only
2= 120/277VAC
3= 120/347VAC
R1= single face red
R2= double face red
G1= single face green
G2= double face green
Options
TP=tamper-proof screws*
VRTP= p
olycarbonate shield
with tamper-proof
screws*
*990.0119-RL= Tamper-proof bit
(sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
• Slim contoured body design
• Durable powder-coated Die-Cast
construction
• Energy efficient - consumes less than
3W
• Universal mounting – wall, end or
ceiling mounting
• Long-life, energy-efficient ALINGAP
technology LED light source reduces
maintenance and energy costs
• Diagnostic/self-test feature comes
standard on all Self-powered models
• Even illumination in both normal and
emergency operation
• Maintenance-free, long-life sealed
nickel-cadmium battery
• Normal AC and emergency DC
operation – 120 to 347V universal AC
input; 6 to 48V universal DC input
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• CSA certified meets or exceeds
CSA 22.2 No. 141 requirements
Wire guards
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
4-5/8” [11.8 cm]
9-3/4” [24.8 cm]
Features
8-7/8” [23 cm]
Die-Cast Aluminum “Exit” Sign
6-1/4” [16 cm]
legend™
CX2000 Series
Supply and install the Ready-Lite® CX2000 Series LED Exit Signs. The equipment shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than 3W and universal two-wire DC input voltage
from 6VDC to 48VDC at less than 1.5W for single and double face signs. The faceplate(s) and the back plate
shall snap together and shall be made of Die-Cast aluminum. The light source shall be light emitting diodes
(LED). The LED lamps shall provide illumination in normal and emergency operation and shall be mounted
inside the exit on a plastic frame/reflector. Red LED technology shall be ALINGAP. An LED-sensitive diffuser
shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with even illumination.
The Self-powered model shall stay illuminated during emergency operation for at least 90 minutes (red) and at
least 60 minutes (green) upon AC failure. The Self-powered model shall include self-testing and self-diagnostic
functions: the equipment shall automatically test itself for 5 minutes every 30 days, 30 minutes every 60 days
and 90 minutes annually. A “Service Required” lamp shall be located near the test switch and flash in the
case of a fault detection. A two-LED diagnostic display shall be located inside the equipment and shall be
capable of identifying the source of failure that may occur (battery, charger circuitry, or LED lamp failure).
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite® Model:
.
13-1/8” [33 cm]
1-3/4” [4.3 cm]
14” [35 cm]
Power consumption
Model
AC Specs
DC Specs
AC/DC red
120/347VAC
less than 2W
6 to 48VDC
AC/DC green
120/347VAC
less than 2W
6 to 48VDC
less than 1.5W
less than 1.5W
self-powered red
120/347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
self-powered green
120/347VAC
less than 3W
nickel-cadmium battery
min. 60 minutes
ordering information
Series
CX2= exit
Faces
100U= single face, universal mount
200U= double face, universal mount
Housing/faceplate colours
WH/WH= factory white
BK/BK= black
BA/BA= brushed aluminum
CH= all chrome
PB= all polished brass
BZ= bronze
BK/BA= black/brushed aluminum
WH/BA= white/brushed aluminum
Other colours available.
EXAMPLE: CX2100UBK/BADC
26
voltage
options
DC= 120 to 347Vac, 6 to 48Vdc
SPD= self-powered diagnostic NiCad,
120/347VAC
NEX= NEXUS® system interface*
TP= tamper-proof screws*
VRTP= p
olycarbonate shield with
tamper-proof screws*
G= green legend
*Not all options available with NEXUS® System.
Please consult your sales representative
*990.0119-RL= T
amper-proof bit
(sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® CS2000 Series LED “SORTIE’’ Exit Signs. The equipment shall operate with
universal two-wire AC input voltage from 120VAC to 347VAC at less than 3W and universal two-wire DC input
voltage from 6VDC to 48VDC at less than 1.5W for single or double face signs. The faceplate(s) and the back plate
shall snap together and shall be made of Die-Cast aluminum. The Exit Sign shall have a maximum depth of 1-3/4’’.
The light source shall be light emitting diodes (LEDs). The LED lamps shall provide illumination in normal
and emergency operation and shall be mounted inside the exit. Red LED technology shall be ALINGAP. A
LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with
even illumination.
The Self-powered model shall stay illuminated during emergency operation for at least 60 minutes upon AC
failure. The Self-powered model shall include self-testing and self-diagnostic functions: the equipment shall
automatically test itself for 5 minutes every 30 days, 30 minutes every 60 days and 90 minutes annually. A
“Service” pilot light shall be located near the test switch and flash in the case of a fault detection. A two-LED
diagnostic display shall be located inside the equipment and shall be capable of identifying the source of
failure (battery, charger circuitry, or LED lamp failure).
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite® Model:
.
Wire guards
460.0057-RL
wall mount
460.0048-RL
end mount
460.0058-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
9-3/4” [24.8 cm]
8-7/8” [22.5 cm]
6-1/4” [15.7 cm]
4-5/8” [11.8 cm]
18-1/4” [46.4 cm]
1-3/4” [4.3 cm]
legend™
CS2000 Series
Die-Cast Aluminum
“Sortie” Sign
Features
• Durable, powder-coated Die-Cast
construction
• Slim contoured body design
• Diagnostic/self-test feature comes
standard on all Self-powered units
• Universal mounting – wall, end or
ceiling mounting
• Even illumination in both normal and
emergency operation
• Long-life, energy-efficient ALINGAP
technology LED light source reduces
maintenance and energy costs
• Energy efficient – consumes less
than 3W
• Maintenance-free, long-life sealed
Nickel-Cadmium battery
• Normal AC and emergency DC
operation – 120 to 347V universal AC
input; 6 to 48V universal DC input
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
19-1/8” [48.7 cm]
Power consumption
Model
AC Specs
DC Specs
AC/DC
120/347VAC
less than 2W
6 to 48VDC
less than 1.5W
self-powered
120/347VAC
less than 3W
nickel-cadmium battery
min. 60 minutes
ordering information
Series
CS2= L ED sortie
Faces
100U= single face, universal mount
200U= double face, universal mount
Housing/faceplate colours
voltage
options
WH/WH= white/white
BK/BK= black/black
WH/BA= white/brushed aluminum
BK/BA= black /brushed aluminum
BA/BA= b
rushed aluminum/brushed
aluminum
CH/CH= chrome/chrome
DC= 120VAC to 347VAC, 6VDC to 48VDC
SPD= self-powered diagnostic NiCad,
120/347VAC
NEX= NEXUS® wired system interface*
TP= tamper-proof screws*
VRTP= p
olycarbonate shield with
tamper-proof screws*
*Not all options available with NEXUS®
System. Please consult your sales
representative
Other colours available.
EXAMPLE: CS2100UWH/WHDC
27
*990.0119-RL= Tamper-proof bit
(sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
• Thin profile, 2-piece extruded
aluminum housing
• Pre-specified mounting
• Universal, field-selectable chevrons
(knockout)
• Energy efficient – consumes less than
3.5W in AC or DC mode
• Long life ALINGAP technology
energy-efficient LED light source
• CSA certified, meets or exceeds CSA
22.2, No. 141 and C860 requirements
• Normal AC and emergency DC
operation – 120, 277 or 347V AC input;
6 to 24V DC input
• Available in single or double face
• Indirect refractive technology provides
bright, even illumination
Wire guards
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
4-7/8” [12.5 cm]
9-5/8” [24.3 cm]
Features
8-7/8” [22.5 cm]
Extruded Aluminium Sign
5-5/8” [14.2 cm]
designer
CX4000 Series
Supply and install the Ready-Lite® CX4000 Series LED Exit Sign. The equipment shall operate with universal
AC input voltage of 120/277/347VAC at less than 1.5W and universal two-wire DC input voltage from 6VDC
to 24VDC at less than 1.5W for single and double face signs. The Exit Sign shall consist of a two-piece white
extruded aluminum combined body/faceplate with a maximum depth of 1-1/4”. The exit shall also include
extruded aluminum end caps with white gaskets in order to provide protection to the internal components
and eliminate any possible light leaks. The exit fixture shall be either single or double-faced as shown on the
drawings. The faceplate shall be of a stencil design and will incorporate 6” high letters with a 3/4” stroke.
The canopy shall fasten to the exit body for ease of installation in either ceiling or end mount. The fixture
shall contain a light source, which shall be LED with a long life and shall consist of separate AC and DC LED
sources in the case of AC/DC-remote equipment. Red LED technology shall be ALINGAP.
The Exit Sign in a Self-powered configuration shall be equipped with a Nickel-Cadmium battery and shall stay
illuminated during emergency operation for at least two hours upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite®Model:
.
1-3/8” [3.4 cm]
12-3/8” [31.4 cm]
13” [33.2 cm]
POwer consumption
Model
AC Specs
DC Specs
AC/DC standard
120/277/347VAC
less than 1.5W
6 to 48VDC
less than 1.5W
AC/ special DC
120/277/347VAC
less than 1.5W
36 or 48 or 120VDC
less than 3W
120VAC/DC two wires
120VAC
less than 3W
120VDC
less than 3W
self-powered
120/347VAC
less than 3.5W
nickel-cadmium battery
min. 2 hours
ordering information
Series
CX4= LED exit
Faces/mounting
000= single face, wall mount
100= single face, ceiling mount
100E= single face, end mount
200= double face, ceiling mount
200E= double face, end mount
colour
WH= polar white
BK= black
TA= textured aluminum
BA= brushed aluminum
voltage
options
-UL= 120/277/347Vac, 6 to 24Vdc
-LU36= 1
20/277/347Vac-36Vdc, 4 wires
-LU48= 1
20/277/347Vac-48Vdc, 4 wires
-LU120= 120/277/347Vac, 120Vdc, 4 wires
-L0024= 240Vac, no dc*
-ISP= self-powered, 120/347VAC
-ISP2= self-powered, 120/277VAC
-L120-2W= 1
20Vac-120Vdc -2 wires
TP= tamper-proof screws*
*Consult your sales representative for availability and
other DC voltages.
*990.0119-RL= T
amper-proof bit
(sold separately)
E X A M P L E : C X 4 0 0 0 W H - U LT P
28
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® CS4000 Series LED Exit Sign. The equipment shall operate with universal
AC input voltage of 120/277/347VAC at less than 1.5W and universal two-wire DC input voltage from 6VDC
to 24VDC at less than 1.5W for single and double face signs. The Exit Sign shall consist of a two-piece white
extruded aluminum combined body/faceplate with a maximum depth of 1-1/4”. The exit shall also include
extruded aluminum end caps with white gaskets in order to provide protection to the internal components
and eliminate any possible light leaks. The exit fixture shall be either single or double-faced as shown on the
drawings. The faceplate shall be of a stencil design and will incorporate 6” high letters with a 3/4” stroke. The
canopy shall fasten to the exit body for ease of installation in either ceiling or end mount.
The fixture shall contain a light source, which shall be LED with a long life and shall consist of separate AC
and DC LED sources in the case of AC/DC-remote equipment. Red LED technology shall be ALINGAP.
The Exit Sign in a Self-powered configuration shall be equipped with a Nickel-Cadmium battery and shall stay
illuminated during emergency operation for at least two hours upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite®Model:
.
Wire guards
460.0057-RL
wall mount
460.0048-RL
end mount
460.0058-RL
ceiling mount
Dimensions are approximate and subject to change.
9-5/8” [24.3 cm]
4-7/8” [12.5 cm]
8-7/8” [22.5 cm]
Extruded Aluminum
“Sortie” Sign
Features
• Thin profile, two-piece extruded
aluminum housing
• Mounting to be pre-specified
• Universal field-selectable chevrons
(knockout)
• Indirect refractive lighting technology
provides bright, even illumination
• Long life, energy-efficient ALINGAP LED
light source
• Energy efficient: consumes less than
3.5W
• Normal AC and emergency DC
operation – 120/277/347Vac and 6V
to 24Vdc input
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Dimensions
5-5/8” [14.2 cm]
CS4000 Series
1-3/8” [3.4 cm]
19-1/8” [48.6 cm]
19-7/8” [50.4 cm]
Power consumption
Model
AC Specs
DC Specs
AC/DC standard
120/277/347VAC
less than 1.5W
6 to 48VDC
less than 1.5W
AC/ special DC
120/277/347VAC
less than 1.5W
36/48/120VDC
less than 3W
120VAC/DC two wires
120VAC
less than 3W
120VDC
min. 3W
self-powered
120/347VAC
less than 3.5W
nickel-cadmium battery
min. 2 hours
ordering information
Series
CS4= sortie
Faces/mounting
000= single face, wall mount
100= single face, ceiling mount
100E= single face, end mount
200= double face, ceiling mount
200E= double face, end mount
colour
voltage
WH= polar white
BK= black
TA= textured aluminum
BA= brushed aluminum
UL= 120/277/347Vac, 6 to 24Vdc
LU36= 120/277/347Vac, 36Vdc
LU48= 120/277/347Vac, 48Vdc
LU120= 120/277/347Vac, 120Vdc
ISP= self-powered, 120/347VAC
LI20-2W= 1
20Vac - 120Vdc - 2 wires
options
TP= tamper-proof screws*
*990.0119-RL= Tamper-proof bit
(sold separately)
E X A M P L E : C S 4 0 0 0 W H U LT P
29
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® CX4000BIL & CS4000BIL Series LED Exit Sign. The equipment shall operate
with universal AC input voltage of 120/277/347VAC at less than 1.5W and universal two-wire DC input voltage
from 6VDC to 24VDC at less than 2.5W for single and double face signs. The Exit Sign shall consist of a
two-piece white extruded aluminum combined body/faceplate with a maximum depth of 1 1/4”. The exit shall
also include extruded aluminum end caps with white gaskets in order to provide protection to the internal
components and eliminate any possible light leaks. The exit fixture shall be either single or double-faced as
shown on the drawings. The faceplate shall be of a stencil design and will have 6” high letters with a 3/4”
stroke indicating both EXIT and SORTIE side by side. The canopy shall fasten to the exit body for ease of
installation in either ceiling or wall mount. The fixture shall contain a light source, which shall be LED with a
long life and shall consist of separate AC and DC LED sources in the case of AC/DC-remote equipment. Red
LED technology shall be ALINGAP.
The Exit Sign in a Self-powered configuration shall be equipped with a Nickel-Cadmium battery and shall stay
illuminated during emergency operation for at least two hours upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite®Model:
.
CX4000BIL &
CS4000BIL Series
Bilingual Extruded
Aluminum Sign
Features
• Thin profile, 2-piece extruded
aluminum housing
• Pre-specified mounting
• Universal, field-selectable chevrons
(knockout)
• Energy efficient – consumes less than
7W in AC or DC mode
• Normal AC and emergency DC
operation 120, 277 or 347V AC input;
6 to 24V DC input
• Available in single or double face
• Custom wording available on request
• Indirect refractive technology provides
bright, even illumination
• Long-life ALINGAP technology,
energy-efficient LED light source
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Wire guards
460.0059-RL
wall mount
460.0092-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
5-5/8” [14.2 cm]
5-5/8” [14.2 cm]
8-7/8” [22.5 cm]
9-5/8” [24.3 cm]
4-7/8” [12.5 cm]
1-3/8” [3.4 cm]
30-3/8” [77.1 cm]
30-3/8” [77.1 cm]
POwer consumption
Model
AC Specs
DC Specs
AC/DC standard
120/347VAC
less than 2W
6 to 48VDC
less than 3W
AC/ special DC
120/277/347VAC
less than 2W
36 or 48 or 120VDC
less than 6W
120VAC/DC two wires
120VAC
less than 6W
120VDC
less than 6W
self-powered
120 or 347VAC
less than 7W
nickel-cadmium battery
Min. 2 hours
ordering information
Series
CX4= exit sortie
CS4= sortie exit
Faces/mounting
000= s ingle face,
wall mount
100= s ingle face,
ceiling mount
200= d
ouble face,
ceiling mount
approval
BIL
colour
WH= polar white
BK= black
TA= textured aluminum
BA= brushed aluminum
voltage
-UL= 120/277/347VAC, 6 to 24Vdc
-LU36= 120/277/347Vac-36Vdc
-LU48= 120/277/347/Vac-48Vdc
-LU120= 120/277/347/VAC-120Vdc
-ISP= self-powered, 120Vac
-ISP3= self-powered, 347Vac
-L120-2W= 1
20Vac-120Vdc-2 wires
options
TP= tamper-proof screws*
*990.0119-RL= T
amper-proof bit
(sold separately)
E X A M P L E : C X 4 0 0 0 B I LTA - U L
30
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® RA Series pictogram Exit Signs. The equipment shall operate with universal
2-wire AC input voltage of 120 to 347VAC at less than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC
at less than 1.5W for single and double face signs. The equipment shall be suitable for wall, end, or ceiling mount.
The housing shall be constructed of rugged extruded aluminum and have a maximum depth of 2-1/2”. The
faceplate(s) shall be constructed of extruded aluminum and shall incorporate a protective clear polycarbonate
panel. Each face plate shall come standard with two legend films for pictogram and direction selection. The light
source shall be white light-emitting diodes (LED) and shall provide even illumination in normal and emergency
operation. The pictogram Exit Sign in a Self-powered configuration shall use a sealed Nickel-Cadmium battery of
2.4V nominal voltage and shall stay illuminated during emergency operation for at least two hours upon AC failure.
The pictogram Exit Sign shall meet CSA 22.2 No.141-10.
The equipment shall be Ready-Lite® Model:
.
RA Series
Extruded Aluminum Pictogram
Exit Sign
Features
Wire guards
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
Pictogram
Straight from here
7-3/4” [19.7 cm]
6-3/8” [16.2 cm]
< Pictogram
Left from here
8-3/4” [22.3 cm]
4-3/4” [11.9 cm]
13-1/8” [33.3 cm]
2-1/2” [6.3 cm]
14-1/8” [35.9 cm]
Pictogram >
Right from here
Power consumption
Model
AC Specs
DC Specs
AC-only
120 to 347VAC
less than 2.5W
-
-
AC/DC standard
120 to 347VAC
less than 2.5W
6 to 24VDC
less than 1.5W
less than 2.5W
AC/Special DC
120 to 347VAC
less than 2.5W
36, 48, 120VDC
two-wire 120V AC/DC
120VAC
less than 2.5W
120VDC
less than 2.5W
self-powered
120 to 347VAC
less than 3W
nickel-cadmium battery
minimum two hours
• Durable extruded, one-piece
aluminum housing and face plates
• White LED light source
• Supplied standard with two pictogram
films (single face universal mount and/
or single/double face universal mount)
for direction selection
• Meets or exceeds CSA 22.2 No.14110 standard for pictogram exit signs
• Universal AC input: two-wire 120 to
347VAC; standard DC input: two-wire
6 to 24VDC
• Energy efficient – consumes less than
2.5W in AC or DC-remote mode
• Self-powered model gives standard
two hours of back-up lighting
• Universal mounting – end, wall or
ceiling
• Easy access to wiring entry for all
mounting options
• Comes standard with the Ready-Lite®
EZ2 canopy for quick and easy
installation
Ordering Information
Series
RA= pictogram
exit sign
FaceS / Mounting
1= single face
universal mount
2= double face
universal mount
3= single/double face
universal mount
housing colour
W= factory white
B= black
G= grey
A= brushed aluminum
Other colours available
Voltage
U= 120 to 347VAC; 6 to 24VDC
SP= self-powered, 120 to 347VAC
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
2120= 2-wires 120VAC/VDC
SPD= self-powered diagnostic NiCad, 120/347VAC
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
*Not all options available with NEXUS® System.
Please consult your sales representative
EXAMPLE: RA1WUTP
31
Options
TP= tamper-proof screws*
VR= vandal-resistant shield and tamper-proof
screws*
*990.0119-RL= T
amper-proof bit (sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Features
• Durable, extruded, one-piece
aluminum housing
• Long-life, energy-efficient ALINGAP
technology red LED light source
completely enclosed in acrylic module
• Single illumination module lights both
single and double face exit signs
• Highly energy efficient – consumes
less than 2.5W in AC or DC mode
• Normal AC and emergency DC
operation - 120/277/347V AC input;
6 to 24V DC input
• Comes with the Ready-Lite® EZ2
canopy for quick and easy installation
• Also available with power pack; see
SM-CX5000 catalogue sheet
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Wire guards
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
4-3/4” [11.9 cm]
13-1/8” [33.3 cm]
8-3/4” [22.3 cm]
Extruded Aluminum Sign
7-3/4” [19.7 cm]
CX5000 Series
Supply and install the Ready-Lite® CX5000 Series LED Exit Signs. The equipment shall operate with universal
AC input voltage of 120VAC, 277VAC or 347VAC at less than 1.5W and universal two-wire DC input voltage
from 6VDC to 24VDC at less than 1.5W for single or double face signs.
The housing shall be constructed of rugged extruded aluminum and have a maximum depth of 2-1/2”. The
faceplate(s) shall be constructed of extruded aluminum and come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). The LED lamps shall provide illumination in normal and
emergency operation and shall be mounted inside the exit housing. The red LED technology shall be ALINGAP.
An LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters
with even illumination. The Exit Sign in a Self-powered configuration shall stay illuminated during emergency
operation for at least 90 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite® Model: ____________________________________________________
2-1/2” [6.3 cm]
14-1/8” [35.9 cm]
POwer consumption
Model
AC Specs
DC Specs
AC/ standard DC, red
120/277/347VAC
less than 1.5W
6 to 24VDC
AC/ special DC, red
120/277/347VAC
less than 1.5W
36 or 48 or 120VDC
less than 1.5W
less than 2.5W
Self-powered, red
120 to 347VAC
less than 3W
nickel-cadmium battery
minimum 90 minutes
AC/ standard DC, green
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
self-powered, green
120 to 347VAC
less than 3W
nickel-cadmium battery
minimum 90 minutes
ordering information
Series
Faces/mounting
CX5= LED exit
100= s ingle face,
universal mount
200= d
ouble face,
universal mount
colour
WH= factory white
BK= black
BA= brushed aluminum
TA= textured aluminum
PW= polar white
voltage
-UL= 120/277/347VAC, 6 to 24VDC
-L120-2W= 120VAC, 120VDC 2 wires
-LU36= 120/277/347VAC - 36VDC
-LU48= 120/277/347VAC - 48VDC
-LU120= 120/277/347VAC - 120VDC
-ISP= self-powered, 120 to 347VAC
options
TP= tamper-proof screws*
VRTP= v andal resistant shield with
tamper-proof screws*
G= green legend
*990.0119-RL= T
amper-proof bit (sold separately)
EXAMPLE: CX5100WH-UL
32
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® CS5000 Series LED “SORTIE’’ Exit Signs. The equipment shall operate with
universal two-wire AC input voltage of 120VAC to 347VAC at less than 1.5W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 1.5W for single or double face signs.
The housing shall be constructed of rugged extruded aluminum and have a maximum depth of 2-1/2”. The
faceplate(s) shall be constructed of extruded aluminum and come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). The LED lamps shall provide illumination in normal and emergency operation and shall be mounted inside the exit housing. The red
LED technology shall be ALINGAP. An LED-sensitive diffuser shall be mounted behind the legend
to provide the 6” high by 3/4” stroke letters with even illumination. The Exit Sign in a Self-powered
configuration shall stay illuminated during emergency operation for at least 60 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved.
The equipment shall be Ready-Lite® Model:
wall mount
460.0048-RL
end mount
460.0058-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
7-3/4” [19.7 cm]
8-3/4” [22.3cm]
4-3/4” [11.9 cm]
6-3/8” [16.2 cm]
Extruded Aluminum
“Sortie” Sign
Features
• Durable, extruded, one-piece aluminum
housing
• Long life ALINGAP technology LED light
source is completely enclosed in
acrylic module
• Single illumination module lights both
single and double face exit signs
• Highly energy efficient, consumes a
maximum of 3W
• Normal AC and emergency DC
operation – 120V to 347Vac;
6V to 24Vdc input
• Also available with power pack; see
SM-CS5000 catalogue sheet
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
• Comes with Ready-Lite® EZ2 canopy, for
quick and easy installation
Wire guards
460.0057-RL
CS5000 Series
2-1/2” [6.3 cm]
18-3/4” [47.5 cm]
19-3/4” [50.1 cm]
POwer consumption
Model
AC Specs
DC Specs
AC/ standard DC, red
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
AC/ special DC, red
120/277/347VAC
less than 1.5W
36 or 48 or 120VDC
less than 3W
self-powered, red
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 60 or 120 minutes
ordering information
Series
CS= aluminum
sortie
Faces/mounting
5100= single face/universal mount
5200= double face/universal mount
Colour
voltage
WH= factory white
BK= black
TA= textured aluminum
PW= polar white
BA= brushed aluminum
-UL= 120/277/347Vac, 6 to 24Vdc
-L120-2W= 1
20Vac, 120Vdc 2 wires
-LU36= 120/277/347Vac - 36Vdc
-LU48= 120/277/347Vac - 48Vdc
-LU120= 120/277/347Vac - 120Vdc
-ISP= self-powered, 120 to 347VAC
options
TP= tamper-proof screws*
VRTP=vandal resistant shield with
tamper-proof screws*
G= green legend
*990.0119-RL= T
amper-proof bit (sold separately)
EXAMPLE: CS5100WH-UL
33
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Dimensions
cm
]
Dimensions are approximate and subject to change.
”[3
11-1/8”[30.0cm]
1/8
3.3
133.3
]
cm
• Rugged extruded aluminum housing
• Extruded aluminum faceplates
• White finish standard
• Standard field-selectable knockout
chevrons
• Long life, energy-efficient LED light
source
• ALINGAP technology LED
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
”[3
Features
1/8
Triangular Extruded Aluminum
Exit Sign
13-
CX5 Series
Supply and install the Ready-Lite ® CX5 Series of three-face LED Exit Signs. The equipment shall
operate with universal AC input voltage of 120, 277 or 347VAC at less than 2W and universal two-wire
DC input voltage from 6VDC to 24VDC at less than 3.5W. The housing shall be constructed of rugged
extruded aluminum painted with a factory white finish and shall have three face plates oriented
symmetrically at 120 degrees in the horizontal plan.
The faceplates shall be constructed of extruded aluminum and come standard with knockout
chevrons. The light source shall be red light emitting diodes (LED) of long-life technology ALINGAP. An
LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by ¾” stroke letters with
even illumination. Each legend shall be illuminated by one dedicated LED lamp (strip). The LED lamps shall be
oriented two downwards and one upwards and shall provide illumination in normal and emergency operation.
Eventual failure of one LED lamp shall not affect the well-functioning of the other two lamps. The 3 sided exit
sign shall come standard with a pendant kit with a 3/8” diameter pipe for ceiling-mount installation.
The Exit Sign shall be C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite® Model:
.
7-3/4”[19.7cm]
13-1/8”[33.3cm]
13-1/8”[33.3cm]
power consumption and unit rating
Model
AC / DC - standard
AC Specs
120/277/347VAC
DC Specs
less than 2W
6 to 24VDC
less than 3.5W
ordering information
Series
CX5= exit extruded aluminum
Faces/ mounting
1002S= 2
sided face (wall mounting only)
1003S= 3
sided face (pendant mounting only)
colour
WH= factory white
voltage
UL= 120/277/347Vac,
6 to 24Vdc
options
TP= tamper-proof screws*
*990.0119-RL= T
amper-proof bit
(sold separately)
EXAMPLE: CX51002SWHUL
34
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® CX5000R Series Exit Sign. The CX5000R exit shall be recessed mount.
The equipment shall operate with universal AC input voltage of 120, 277 or 347VAC at less than 1.5W and
universal two wire DC input voltage from 6VDC to 24VDC at less than 1.5W. The face shall be constructed
of extruded aluminum and have an overlapping trim allowing for installation in any location. The faceplate
shall come standard with knockout chevrons. The recessed back box shall be of rugged steel construction.
The light source shall be light emitting diodes (LED). Red LED technology shall be ALINGAP. The LED lamps
shall provide illumination in normal and emergency operation and shall be mounted inside the exit housing.
An LED sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters
with even illumination.
The Exit Sign in a Self-powered configuration shall be equipped with a Nickel-Cadmium battery and shall stay
illuminated during emergency operation for at least 90 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Ready-Lite®Model:
.
Wire guards
460.0091-RL
wall mount
Dimensions
Dimensions are approximate and subject to change.
2-1/2” [6.5 cm]
12-3/4” [32.4 cm]
7-1/2” [19 cm]
8-7/8” [22.7 cm]
2-1/4” [5.7 cm]
CX5000R Series
Recessed Exit Sign
Features
• Extruded aluminum faceplate with
overlapping trim is standard
• Universal, field-selectable chevrons
(knockout)
• Long-life, energy-efficient ALINGAP LED
light source
• Indirect refractive technology provides
bright, even illumination
• Normal AC and emergency DC
operation – 120 to 347V universal AC
input; 6 to 24V two-wire DC input
• Energy efficient – consumes less than
3.5W in AC or DC mode
• Nickel-Cadmium battery provides at
least 90 minutes of emergency
operation in DC mode
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
14-3/4” [37.5 cm]
POwer consumption
Model
AC Specs
DC Specs
AC/ standard DC, red
120/277/347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
AC/ special DC, red
120/277/347VAC
less than 3W
36 or 48 or 120VDC
less than 2.5W
minimum 90 minutes
Self-powered, red
120 to 347VAC
less than 3W
nickel-cadmium battery
AC/ standard DC, green
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
self-powered, green
120 to 347VAC
less than 3.5W
nickel-cadmium battery
minimum 90 minutes
ordering information
Series
CX5000R= L ED aluminum
recessed exit
colour
WH= factory white
BK= black
BA= brushed aluminum
TA= textured aluminum
voltage
-UL= 120/277/347VAC, 6 to 24VDC
-L120-2W= 120VAC, 120VDC 2 wires
-LU36= 120/277/347VAC - 36VDC
-LU48= 120/277/347VAC - 48VDC
-LU120= 120/277/347Vac - 120VDC
-ISP= self-powered, 120 to 347VAC
options
TP= tamper-proof screws*
VRTP= polycarbonate shield and tamper-proof screws*
G= green legend
*990.0119-RL= T
amper-proof bit (sold separately)
EXAMPLE: CX5000RWH-UL
35
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
CX7000 &
CS7000 series
Bilingual Extruded Aluminum
Exit Sign
Features
• Durable, extruded, one-piece
aluminum housing
• Long-life, energy-efficient ALINGAP
technology red LED light source
completely enclosed in acrylic module
• Single illumination module lights both
single and double face Exit Signs
• Highly energy efficient, consumes a
maximum of 5.5W in AC or DC mode
(standard model)
• Normal AC and emergency DC
operation – 120V to 347Vac and
6V to 24Vdc input
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Supply and install the Ready-Lite® bilingual CX7000 & CS7000 Series LED Exit Sign. The equipment shall
operate with universal AC input voltage of 120 to 347VAC at less than 2W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 3.5W for single and double face signs. The housing shall be
constructed of rugged extruded aluminum and have a maximum depth of 2-1/2”. The faceplate(s) shall be
constructed of extruded aluminum and come standard with knockout chevrons. The equipment shall have
two (2) canopies that shall fasten for installation in either ceiling- or wall-mount applications. The light source
shall be light emitting diodes (LED).
The LED lamps shall provide illumination in normal and emergency operation and shall be mounted inside
the exit housing. Red LED technology shall be ALINGAP An LED-sensitive diffuser shall be mounted behind
the legend to provide the 6” high by 3/4” stroke letters with even illumination.
The Exit Sign in a Self-powered configuration shall be equipped with a Nickel-Cadmium battery and shall stay
illuminated during emergency operation for at least 60 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141
The equipment shall be Ready-Lite® Model:
.
Wire guards
460.0059-RL
wall mount
460.0092-RL
ceiling mount
POwer consumption
Model
AC Specs
DC Specs
AC/ standard DC, red
120 to 347VAC
less than 3W
6 to 24VDC
less than 3.5W
AC/ special DC, red
120/277/347VAC
less than 5.5W
36 or 48 or 120VDC
less than 5.5W
Self-powered, red
120/347VAC
less than 6W
nickel-cadmium battery
Min. 60 to 120 minutes
36
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Dimensions
Dimensions are approximate and subject to change.
CX7000 &
CS7000 series
Bilingual Extruded Aluminum
Exit Sign
2-1/2” [6.3 cm]
7-3/4” [19.7 cm]
29” [73.3 cm]
8-3/4” [22.3 cm]
7-3/4” [19.7 cm]
7-3/4” [19.7 cm]
4-3/4” [11.9 cm]
29” [73.3 cm]
ordering information
lettering
CX= exit sortie 6” letters
CS= sortie exit 6” letters
faces
7100= single face
7200= double face
Colour
WH= factory white
BA= brushed aluminum
TA= textured aluminum
BK= black
voltage
-UL= 120 to 347Vac, 6 to 24Vdc
-L120-2W= 1
20Vac, 120Vdc 2 wires
-LU36= 120/277/347Vac - 36Vdc
-LU48= 120/277/347Vac - 48Vdc
-LU120= 1
20/277/347Vac - 120Vdc
-ISP= s elf-powered, 120/347VAC
options
TP= tamper-proof screws*
VRTP= p
olycarbonate shield with tamper-proof
screws*
90= s elf-powered (90 mins.)
120= self-powered (120 mins.)
3C= 3 canopies
*990.0119-RL= T
amper-proof bit (sold separately)
EXAMPLE: CX7100WH-UL
37
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RAC Series
Extruded Aluminum
Pictogram Exit Combo Unit
Features
• Solid extruded aluminum
construction, painted factory white
• Universal mounting: end, wall or ceiling
• Meets or exceeds CSA 22.2 No.141-10
standard for unit equipment and
pictogram safety signs
• Legend illuminated by long-life white
LED’s
• Comes standard with two pictogram
films per face, for direction selection
• 5W LED emergency lights provide 70’
of egress illumination on a 6-foot wide
path
• Sealed, maintenance-free
Lead-Calcium battery
• Remote load capacity: 70’ up to 350’ of
egress illumination when using LED
remote heads
Supply and install the Ready-Lite® RAC Series combination emergency light battery unit and the pictogram
Exit Sign. The unit shall be suitable for universal mounting: wall, end, or ceiling. The unit shall include a
power pack made of steel and a legend housing including a one-piece extruded aluminum frame. The legend
housing shall have a maximum depth of 2-1/2”. The face plate(s) shall be of extruded aluminum and shall
incorporate a protective clear polycarbonate panel. Each face plate shall come standard with two legend
films for pictogram and direction selection. The light source shall be white light-emitting diodes (LED) and
shall provide even illumination in normal and emergency operation. The power pack shall be complete unit
equipment with battery charger and rechargeable battery. The battery shall be maintenance-free, sealed
Lead-Calcium. In case of AC power failure the equipment shall provide minimum 30 minutes of emergency
lighting. The rated DC power available for emergency lights shall be 27W or up to 80W, as specified. The
emergency heads shall require no tools to adjust and aim. The heads shall be made of durable thermoplastic
construction as otherwise specified. Units with “auto-diagnostic option” shall include a micro-controller circuit
to monitor all the critical functions of the equipment and execute periodical tests of one minute every 30
days, 10 minutes every 6 months and 30 minutes every 12 months. In case of equipment malfunction, an
LED-based diagnostic display shall generate a service alarm and indicate the cause of failure: battery, charger
circuit, emergency lamps or exit sign lamps.
The equipment shall meet or exceed the requirements of CSA 22.2 No.141-10 standard.
The equipment shall be Ready-Lite® Model:
.
Wire guards
460.0080-RL
wall mount
460.0060-RL
ceiling mount
460.0060-RL
end mount
Power Consumption
MODEL
pictogram module
AC SPECS
120/347VAC
less than 1.5W
RAC-627
RAC-640
120/347VAC
0.15/0.05 A
RAC-672
RAC-1250
RAC-1280
120/347VAC
38
0.25/0.09 A
Emergency power available for lamps
30min
1h00
1h30
2h00
4h00
-
-
-
-
-
27
16
11
9
-
40
23
16
13
-
72
42
30
24
12
50
29
21
16
8
80
46
32
27
13
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
1-1/8” [2.8 cm]
Dimensions are approximate and subject to change.
RAC Series
4-5/8” [11.7 cm]
Extruded Aluminum Pictogram
Exit Combination Unit
12-3/4” [32.4 cm]
Pictogram
Straight from here
Pictogram >
Right from here
7-1/2” [19.0 cm]
12-1/8” [30.8 cm]
< Pictogram
Left from here
6-1/2” [16.5 cm]
13-1/8” [33.3 cm]
14-1/2” [36.7 cm]
Ordering Information
Series
RAC= p
ictogram
aluminum
combination unit
Faces /
Mounting
1= single face
universal
mounting
2= double face
universal
mounting
Colour
powerpack
Heads
W= factory
white
B= black
627= 6V-27W
640= 6V-40W
672= 6V-72W
1250= 12V-50W
1280= 12V-80W
Blank= no heads
1= one head
2= two heads
Head style and wattage
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
MB= MR16 halogen, 12V-35W*
MR= MR16 high-output, 12V-35W*
RT9= mini tungsten, 9W
RT18= m
ini tungsten, 12V-18W,
wedge base
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
Options
U2= 120/277VAC input
AD= auto-diagnostics*
ADN= auto-diagnostics, non-audible*
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
D3= time delay (15 mins.)
TP= tamper-proof screws**
*Not available With 6V-72W
*Not all options available with NEXUS®
System. Please consult your sales
representative
*MB & MR RL150 type heads
EXAMPLE: RAC1W6272LD1D3
39
**990.0119-RL= T
amper-proof bit
(sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Wire guards
460.0080-RL
wall mount
460.0060-RL
ceiling mount
460.0060-RL
end mount
Dimensions
Dimensions are approximate and subject to change.
4-5/8” [11.7 cm]
6-1/2” [16.5 cm]
13-1/8” [33.3 cm]
12-1/8” [30.8 cm]
4-5/8” [11.7 cm]
12-1/4” [31.3 cm]
13-1/2” [34.2 cm]
Exit Sign
• Extruded aluminum faceplate
• Universal, field-selectable chevrons
(knockout)
• ALINGAP LED technology
Power Pack
• Completely self-contained unit with
rechargeable sealed lead battery
• Lamp heads require no tools to adjust
or aim
• Meets or exceeds CSA 22.2 No. 141
requirements
11” [28.0 cm]
Features
7-1/2” [19.0 cm]
Extruded Aluminum
Combination Unit - 6/12V
12-1/8” [30.8 cm]
SM-CX5000 Series
Supply and install the Ready-Lite® SM-CX5000 LED Exit Sign and power pack combination series. The exit
housing shall be constructed of rugged extruded aluminum. The faceplate shall be constructed of extruded
aluminum. The Exit Sign shall have a maximum depth of 2-1/2”. The faceplate(s) shall come standard
with knockout chevrons.The light source shall be light emitting diodes (LED). The LED lamps shall provide
illumination in normal and emergency operation and shall be mounted inside the exit housing. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with even illumination.
The power pack shall be a completely self-contained emergency unit with its own charger and rechargeable
battery. The housing shall be made of steel, painted factory white. The unit shall be designed to furnish exit
illumination from the normal AC source. When a power failure occurs the mounted heads along with the Exit
Sign are illuminated in emergency mode for a minimum of 30 minutes. The power pack is furnished with a
test switch and high charge pilot light and is available as either 18, 36 or 72W. The heads shall require no
tools to adjust and aim. The heads will be constructed of a durable thermoplastic construction and use 6V,
9W lamps or as otherwise specified. The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
.
5-5/8” [14.3 cm]
14-1/2” [36.7 cm]
POwer consumption and unit rating
Model
AC Specs
30min
1h00
Wattage Capacity
1h30
2h00
4h00
Exit Sign Module
less than 1.5W
-
-
-
-
-
SM18-6V
0.15/0.05 A
18
10
7
6
3
SM36-6V
0.15/0.05 A
36
21
15
12
6
0.18/0.07 A
72
42
30
24
12
SM36-12V
0.18/0.07 A
36
21
15
12
6
SM72-12W
0.15/0.05 A
72
42
30
24
12
SM72-6W
120/347VAC
ordering information
powerpack
SM18= 6V-18W*
SM36= 6V, 12V-36W
SM72= 6V, 12V-72W
number of
heads
Blank= n
o
heads
1= one head
2= two heads
head style and wattage
faces/mounting
voltage
colour
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
RT9= mini tungsten, 9W
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
-CX5100= single
face,
universal
mounting
-CX5200= double
face,
universal
mounting
Blank= 120/347Vac,
6VDC
LO62= 277Vac, 6VDC
L12U= 120/347Vac,
12VDC
L122= 2
77Vac,
12VDC
Blank= factory
white
BK= black
BA= brushed
aluminum*
TA= textured
aluminum*
options
Blank= no options
AD= auto-diagnostics
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
D3= time delay (15 mins.)
G= green legend
R3= remote test receiver**
*Not all options available with NEXUS®
System. Please consult your sales
representative
*Available in 6V only
*Black heads
EXAMPLE: SM181RT9-CX5100
40
**R4= r emote test transmitter
(sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® SMCS5000 LED “SORTIE’’ Exit Sign with power pack combination series.
The exit housing and the faceplate(s) shall be constructed of rugged extruded aluminum. The Exit Sign shall
have a maximum depth of 2-1/2”. The faceplate(s) shall come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). Red LED technology shall be ALINGAP. The LED lamps
shall provide illumination in normal and emergency operation and shall be mounted inside the exit housing.
An LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters
with even illumination. The power pack shall be a completely self-contained emergency unit with its own
charger and rechargeable battery. The housing shall be made of steel. The unit shall be designed to furnish
exit illumination from the normal AC source. When a power failure occurs, the mounted heads along with
the Exit Sign are illuminated in emergency mode for a minimum of 30 minutes. The power pack is furnished
with a test switch and high charge pilot light and is available as either 18, 36 or 72W. The heads shall require
no tools to adjust and aim. The heads will be constructed of polycarbonate and include 6V, 9W lamps or as
otherwise specified.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Ready-Lite® Model:
.
Wire guards
460.0081-RL
wall mount
460.0060-RL
ceiling mount
Dimensions
12-1/4” [31.1 cm]
7-1/2” [19.0 cm]
12-1/8” [30.8 cm]
Dimensions are approximate and subject to change.
1-1/8” [2.8 cm]
4-5/8” [11.7 cm]
6-1/2” [16.5 cm]
18-3/4” [47.5 cm]
20-1/8” [51.0 cm]
SM-CS5000
Series
Extruded Aluminum
Combination Unit - 6/12V
Features
• Rugged extruded aluminum housing
with a maximum depth of 2-1/2”
• Extruded aluminum faceplate
• White finish standard
• Standard field-selectable knockout
chevrons
• Long life, energy-efficient LED light
source, mounted inside the exit housing
• ALINGAP technology LED
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• Completely self-contained unit with
rechargeable sealed lead-acid battery
• Lamp heads require no tools to adjust
or aim
• Provides a minimum of 30 minutes of
illumination (lamp heads and exit sign)
in emergency mode
• CSA certified, meets or exceeds
CSA 22.2 No. 141. requirements
POwer consumption and unit rating
Model
AC Specs
30min
Wattage Capacity
1h00
1h30
2h00
4h00
Sortie Sign Module
less than 2W
-
-
-
-
-
SM18-6V
SM36-6V
SM72-6W
SM36-12V
SM72-12V
0.15/0.05 A
0.15/0.05 A
0.18/0.07 A
0.18/0.07 A
0.15/0.05 A
18
36
72
36
72
10
21
42
21
42
7
15
30
15
30
6
12
24
12
24
3
6
12
6
12
120/347VAC
ordering information
series
SM18= 6V-18W*
SM36= 6V, 12V-36W
SM72= 6V, 12V-72W
#of heads
head style and wattage
mounting/faces
voltage
housing colour
options
Blank= no
heads
1= one head
2= two heads
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
RT9= mini tungsten, 9W
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
CS5100= s ingle face,
universal
mounting
CS5200= d
ouble face,
universal
mounting
Blank= 120/347Vac,
6VDC
LO62= 2
77Vac, 6VDC
L12U= 1
20/347Vac,
12VDC
L122= 277Vac, 12VDC
Blank= factory white
BK= black
BA= brushed
aluminum*
TA=textured
aluminum*
Blank= no options
AD= auto-diagnostics
NEX= NEXUS® system
interface*
NEXRF= wireless NEXUS®
system interface*
D3= time delay (15 mins.)
R3= remote test receiver**
*Available in 6V only
*Not all options available
with NEXUS® System.
Please consult your sales
representative
Other styles available consult your
sales representative
*Black heads
EXAMPLE: SM182RT9CS5100
41
**R4= remote test transmitter
(sold separately)
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
• Metal construction using Canadian
cold-rolled steel
• Based on a modular design, this
product comes pre-assembled for
quick, easy installation
• Long-life white LED light source
• Meets or exceeds CSA 22.2 No.14110 standard for pictogram exit signs
• Two-wire universal AC input: 120 to
347VAC; two-wire standard DC input:
6 to 24VDC
• Energy efficient – consumes less than
2.5W in AC mode and only 1W in
DC-remote
• Self-powered model delivers standard
two hours of back-up lighting
• Universal mounting – end, wall
or ceiling
• Easy access to wiring entry for all
mounting options
• Canopy mounting system designed
specifically for ease of installation
• Also available with power pack;
see RSC catalogue sheet
Dimensions
Dimensions are approximate and subject to change.
< Pictogram
Left from here
Pictogram
Straight from here
Pictogram >
Right from here
45/8” [11.7 cm]
87/8” [22.4 cm]
Features
75/8” [19.2 cm]
All Metal Pictogram Exit Sign
73/8” [18.7 cm]
RS Series
Supply and install the Ready-Lite® RS Series pictogram Exit Signs. The equipment shall operate with
universal 2-wire AC input voltage of 120 to 347VAC at less than 2.5W and universal 2-wire DC input
voltage from 6 to 24VDC at 1W consumption for single and double face signs. The sign shall be suitable
for wall, end, or ceiling mount. The frame and back plate shall each be of one-piece steel construction.
The faceplate(s) shall be constructed of robust clear polycarbonate panels with a border coloured factorywhite. The light source shall be white light-emitting diodes (LED) and shall provide even illumination in
normal and emergency operation. The pictogram Exit Sign in a Self-powered configuration shall use a sealed
Nickel-Cadmium battery of 2.4V nominal voltage and shall stay illuminated during emergency operation for
at least two hours upon AC failure.
The Exit Sign shall be listed CSA 22.2 No.141-10.
The equipment shall be Ready-Lite® Model:
.
121/8” [30.7 cm]
133/8” [33.9 cm]
21/8” [5.3 cm]
Wire guards
460.0079-RL
wall mount
460.0027-RL
End mount
460.0028-RL
ceiling mount
Power Consumption
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
less than 2.5W
-
-
AC/DC standard
120 to 347VAC
less than 2.5W
6 to 24VDC
less than 1W
AC/Special DC
120 to 347VAC
less than 2.5W
36, 48, 120VDC
less than 2.5W
Two-wire 120V AC/DC
120VAC
less than 2.5W
120VDC
less than 2.5W
self-powered
120 to 347VAC
less than 2.5W
nickel-cadmium battery
min. 2 hours
Ordering Information
Series
RS= steel pictogram exit sign
FaceS / Mounting
1= s ingle face
universal mounting
2= d
ouble face
universal mounting
3= s ingle/double face
universal mounting
colour
W= factory white
B= black
G= grey
voltage
U= 120 to 347VAC; 6 to 24VDC
SP= self-powered, 120 to 347VAC
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
2120= 2-wires 120VAC/VDC
Options
TP= tamper-proof screws*
VR= v andal-resistant shield and
tamper-proof screws*
*990.0119-RL= T
amper-proof bit (sold separately)
Other colours available
*Not available on universal faces.
EXAMPLE: RS1WUTP
42
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® NEXTN Series Exit Signs. The equipment shall operate with universal 2-wire
AC input voltage of 120 to 347VAC at less than 1.5W and universal 2-wire DC input voltage from 6 to 24VDC
at less than 1.5W for single and double face signs. The sign shall be suitable for wall, end, or ceiling mount.
The faceplates shall be constructed of steel and shall come standard with knockout chevrons. The frame
shall be of one-piece steel construction. The light source shall be light-emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and shall be mounted inside the exit housing.
Red LEDs shall be of ALINGAP technology.
An LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters
with even illumination.The Exit Sign in a Self-powered configuration shall stay illuminated during emergency
operation for at least 90 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Ready-Lite® Model:
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
73/8” [18.7 cm]
7-5/8” [19.2 cm]
8-7/8” [22.4 cm]
4-5/8” [11.7 cm]
12-1/8” [30.7 cm]
2-1/8” [5.3 cm]
13-3/8” [33.9 cm]
POwer consumption
Model
AC Specs
All Metal Exit Sign
Features
• Two-wire universal AC input
• Pre-assembled for quick, easy
installation
• Universal mounting – end, wall or
ceiling
• Supplied with two stencil plates, red
diffusing lenses and backplate
• Easy access to wiring entry for all
mounting options
• Canopy mounting system designed
specifically for ease of installation
• Universal, field-selectable chevrons
(knockout)
• Energy efficient – consumes less than
3W in AC or DC mode
• Normal AC and emergency DC
operation – 120 to 347V AC input;
6 to 24V DC input
• Long life energy-efficient ALINGAP
technology LED light source
• Also available with power pack; see
SM-NEXTN catalogue sheet
• CSA certified, meets or exceeds
CSA 22.2 No. 141. requirements
Wire guards
460.0079-RL
nextn Series
DC Specs
AC-only, red
120 to 347VAC
less than 1.5W
-
-
AC/DC standard, red
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
AC/special DC, red
120/277/ 347VAC
less than 3W
36 or 48 or 120VDC
less than 2.5W
Self-powered red
120 to 347VAC
less than 3W
nickel-cadmium battery
Min. 60 minutes
AC-only, green
120 to 347VAC
less than 1.5W
-
-
AC/DC standard, green
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 2.5W
self-powered green
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
ordering information
Series
NEXTN= LED exit sign /
universal mount
voltage
-LU= universal voltage, 120 to 347VAC 6 to 24VDC
-LU00= 120 to 347Vac, no DC**
-LU36= 120/277/347Vac - 36Vdc*
-LU48= 120/277/347Vac, 48Vdc*
-LU120= 120/347Vac, 120Vdc*
-L120-2W= 120Vac, 120Vdc 2 wires*
-ISP= self-powered, 120 to 347Vac
*For green legend, consult your sales representative.
** Supplied as single face
Colour
options
Blank= factory white
BK= black
TA= textured aluminum
G= green legend
TP= tamper-proof screws*
VRTP1= v andal resistant shield with tamper-proof screws,
single face*
VRTP2= v andal resistant shield with tamper-proof screws,
double face*
Other colours available
*990.0119-RL= T
amper-proof bit (sold separately)
EXAMPLE: NEXTN-LU
43
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
• Metal construction using Canadian
cold-rolled steel with baked enamel
finish – will not yellow
• Metal legend panel with red letter panel
• Universal mounting – end, wall
or ceiling
• Easy access to wiring entry for all
mounting options
• Canopy mounting system designed
specifically for ease of installation
• Standard field-selectable directional
knockout chevrons
• Long life, energy efficient ALINGAP
technology light source
• Energy efficient – consumes less than
3W
• Normal AC and emergency DC
operation – 120V to 347Vac
and 6V to 24Vdc input
• CSA certified, meets or exceeds
CSA 22.2 No. 141. requirements
• Long-life, energy-efficient ALINGAP
technology LED light source completely
enclosed in acrylic module
• Also available with power pack; see
R-SN catalogue sheet
Wire guards
460.0057-RL
wall mount
460.0048-RL
end mount
460.0058-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
4-5/8” [11.7 cm]
18” [45.7 cm]
8-3/4” [22.3 cm]
Features
7-1/2” [19.1 cm]
All Metal “Sortie” Sign
7-1/2” [19.1 cm]
CNESTU Series
Supply and install the Ready-Lite® CNESTU Series LED “SORTIE’’ Exit Signs. The equipment shall operate with
universal two-wire AC input voltage of 120VAC to 347VAC at less than 1.5W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 1.5W for single or double face signs.
The sign shall be suitable for wall, end or ceiling mount. The faceplates shall be constructed of steel and
shall come standard with knockout chevrons. The frame shall be of a one-piece steel construction.The light
source shall be light emitting diodes (LED). The LED lamps shall provide illumination in normal and emergency
operation and shall be mounted inside the exit housing. Red LED technology shall be ALINGAP. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with even illumination.
The Exit Sign in a Self-powered configuration shall stay illuminated during emergency operation for at least
60 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
.
2-1/8” [5.3 cm]
19-1/8” [48.5 cm]
POwer consumption and unit rating
Model
AC Specs
DC Specs
AC/DC standard
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
AC/special DC
120/277/347VAC
less than 2.5W
36 or 48 or 120VDC
less than 2.5W
Self-powered
120 to 347VAC
less than 3W
nickel-cadmium battery
minimum 60 minutes
ordering information
Series
CNEST= LED sortie
Mounting
U= u
niversal mount and face
voltage
Colour
-LU= 120 to 347Vac, 6 to 24Vdc
-ISP= self-powered, 120 to 347Vac
-L120-2W= 120Vac, 120Vdc 2 wires
-LU36= 120/277/347Vac, 36Vdc
-LU48= 120/277/347Vac, 48Vdc
-LU120= 120/347Vac, 120Vdc
EXAMPLE: CNESTU-LU
44
options
Blank= factory white
BK= black
GY= textured grey
TP= tamper-proof screws*
VRTP1= v andal resistant shield with tamper-proof
screws, single face*
VRTP2= v andal resistant shield with tamper-proof
screws, double face*
Other colours available
*990.0119-RL= T
amper-proof bit (sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® bilingual CNEXTN & CNSXTN Series LED Exit Sign. The equipment shall
operate with universal AC input voltage of 120 to 347VAC at less than 3W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 3.5W for single and double face signs. The frame shall be of
one-piece steel construction and have a maximum depth of 2-1/8”. The faceplate(s) shall be steel and
come standard with knockout chevrons. The equipment shall have two (2) canopies that shall fasten for
installation in ceiling-mount applications. The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and shall be mounted inside the exit housing.
Red LED technology shall be ALINGAP. An LED-sensitive diffuser shall be mounted behind the legend to
provide the 6” high by 3/4” stroke letters with even illumination.
The Exit Sign in a Self-powered configuration shall stay illuminated during emergency operation for at least
minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Ready-Lite® Model:
.
Wire guards
460.0059-RL
wall mount
460.0092-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
CNEXTN & CNSXTN
Series
Bilingual Steel Sign
Features
• Single illumination module lights both
single and double face Exit Signs
• Highly energy efficient – consumes a
maximum of 5.5W in AC or DC mode
• Normal AC and emergency DC
operation – 120 to 347V AC input;
6 to 24V DC input
• Meets or exceeds CSA 22.2 No. 141
requirements.
7-3/8” [19 cm]
CNEXTN Series
28-5/8” [73 cm]
CNSXTN Series
7-3/8” [19 cm]
7-1/2” [19 cm]
8-3/4” [22 cm]
4-5/8” [12 cm]
2-1/8” [5 cm]
28-5/8” [73 cm]
POwer consumption and unit rating
Model
AC Specs
DC Specs
AC/DC standard
120 to 347VAC
less than 3W
6 to 24VDC
less than 3.5W
AC/special DC
120/277/347VAC
less than 5W
36 or 48 or 120VDC
less than 5W
self-powered
120 to 347VAC
less than 6W
nickel-cadmium battery
min. 60 or 120 minutes
ordering information
lettering
CNEXTN= e xit sortie 6” letters
CNSXTN= sortie exit 6” letters
faces
11= single face
12= double face
Colour
WH= factory white
BK= black
GY= textured grey
voltage
-LU= 120 to 347Vac, 6 to 24 Vdc
-LI20-2W= 120Vac, 120Vdc, 2 wires
-LU36= 120/277/347Vac - 36Vdc
-LU48= 120/277/347Vac - 48Vdc
-LU120= 120/277/347Vac - 120Vdc
-ISP= s elf-powered, 120 to 347Vac (60 mins.)
-ISP2= s elf-powered, 120 to 347Vac (120 min.)
options
Blank= 2 canopies supplied
TP= tamper-proof screws*
VRTP= v andal resistant shield with
tamper- proof screws*
3C= 3 canopies
*990.0119-RL= T
amper-proof bit (sold separately)
E X A M P L E : C N extn 1 1 W H - L U
45
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical Specification
Wire Guards
460.0080-RL
wall mount
460.0060-RL
ceiling mount
460.0060-RL
end mount
dimensions
Dimensions are approximate and subject to change.
12-5/8” [32.0cm]
4-5/8” [11.7cm]
11” [28.0cm]
Picto
straight from here
4-5/8” [11.7cm]
4-5/8” [11.7cm]
< Picto
left from here
12-1/8” [30.8cm]
Picto >
right from here
7-1/2” [19.1cm]
6-1/2” [16.5cm]
12V-50W &
12V-80W units
6V-44W &
6V-72W units
12-1/4” [31.2cm]
• Universal mounting: end, wall or ceiling
• Meets or exceeds CSA 22.2 No.141-10
standard for unit equipment and
pictogram Exit Signs
• Legend illuminated by long-life white
LED’s
• Sealed, maintenance-free, 6V or 12V
Lead-Calcium battery
• Remote load capacity: 80W up to 560’
of egress illumination when using LED
remote heads
13-1/2” [34.2cm]
Features
12-1/4” [31.0cm]
Steel Pictogram
Combination Unit
13-3/4” [34.8cm]
RSC Series
Supply and install Ready-Lite® RSC Series combination emergency light battery unit and pictogram Exit Sign. The
unit shall be made of solid steel sheet metal and be suitable for universal mounting: wall, end, or ceiling. The
legend housing shall have a maximum depth of 2-1/8”. The legend face plate(s) shall be constructed of robust
clear polycarbonate panel(s) with a border coloured factory-white. The light source shall be white light-emitting
diodes (LED) and shall provide even illumination in normal and emergency operation. The power pack shall
include one circuit board with test switch and pilot light for battery charger and legend LED driver. The unit shall
include one 6V or 12V, maintenance-free, sealed Lead-Calcium battery and shall provide minimum 30 minutes
of emergency lighting upon AC power failure. The electrical power available for emergency lights shall be 28W
or up to 72W, for 6V and 50W or up to 80W for 12V, as specified. The emergency heads shall require no tools
to adjust and aim. The equipment shall meet or exceed the requirements of CSA 22.2 No.141-10 standard.
The equipment shall be Ready-Lite® Model:
.
6” [15.1cm]
13-3/8” [34.0cm]
6V-28W units
Power Consumption
Model
AC Specs
Pictogram Module
RSC28
RSC44
120/347VAC
RSC72
RSC-1250
RSC-1280
less than 1.5W
0.13 / 0.05 A
0.25 / 0.09 A
30min
Emergency power available for lamps
1H00
1H30
2H00
4H00
28
44
72
50
80
16
26
42
29
46
12
18
30
21
32
9
15
24
16
27
7
12
8
13
Ordering Information
Series
RSC= p
ictogram
steel combo
exit sign
powerpack
28= 6V-28W
44= 6V-44W
72= 6V-72W*
1250= 12V-50W
1280= 12V-80W
Housing
colour
W= factory
white
B= black
Heads
Head style and wattage
Blank= no heads
1= one head
2= two heads
*Not available with NEX & NEXRF
EXAMPLE: RSC28W2RT9
46
Options
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
MB= MR16 halogen, 12V-35W*
MR= MR16 high-output, 12V-35W*
RT9= mini tungsten, 9W
RT18= m
ini tungsten, 12V-18W,
wedge base
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
U2= 120/277VAC input
AD= auto-diagnostics*
ADN= auto-diagnostics, non-audible*
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
DF= double face sign
D3= time delay (15 mins.)
TP= tamper-proof screws**
*MB & MR RL150 type heads
**990.0119-RL= Tamper-proof bit (sold separately)
*Not available with 6V-72W
*Not all options available with NEXUS® System.
Please consult your sales representative
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® SM-NEXTN Series LED Exit Sign and power pack combination series. The
exit housing and faceplates shall be constructed of steel. The Exit Sign shall have a maximum depth of
2-1/2”. The faceplate(s) shall come standard with knockout chevrons. The light source for the Exit Sign shall
be light-emitting diodes (LED). The LED lamps shall provide illumination in normal and emergency operation
and shall be mounted inside the exit housing. Red LEDs shall be of ALINGAP technology. An LED sensitive
diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with even illumination.
The power pack shall be a completely self-contained emergency unit with its own charger and rechargeable
battery. The housing shall be made of steel. The power pack shall include a test switch and high charge pilot
light. The equipment shall be designed to furnish exit illumination from the normal AC source. When a power
failure occurs the Exit Sign along with the emergency heads shall illuminate for a minimum of 30 minutes.
The power available for emergency lights shall be 28W or as otherwise specified.The heads shall require no
tools to adjust and aim. The heads will be of a durable thermoplastic construction and use 6V, 9W and 12V,
9W lamps or as otherwise specified. The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
.
Wire guards
460.0080-RL
460.0060-RL
460.0060-RL
wall mount
ceiling mount
end mount
extra faceplates
005406-RL
005407-RL
005408-RL
Factory white faceplate + red diffuser
Black faceplate + red diffuser
Grey faceplate + red diffuser
005409-RL
005410-RL
005411-RL
Factory white faceplate + green diffuser
Black faceplate + green diffuser
Grey faceplate + green diffuser
Dimensions
Dimensions are approximate and subject to change.
4-5/8” [11.7cm]
11” [28cm]
7-3/8”
[18.7cm]
13-3/4” [34.8cm]
12-1/2” [31.7cm]
12-1/8” [30.8cm]
6-1/2” [16.6cm]
12-1/4” [31.2cm]
4-5/8” [11.7cm]
12-5/8” [32.0cm]
SM-NEXTN Series
Metal Combination Unit
Features
• Dual input voltages 120/347Vac
• Comes pre-assembled for quick, easy
installation
• Universal mounting – end, wall or
ceiling
• Easy access to wiring entry for all
mounting options
• Canopy mounting system designed
specifically for ease of installation
• Universal fields-selectable chevrons
(knock out)
• Energy efficient – complete unit
consumes less than 5W
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
• Long life, energy-efficient LED light
source, mounted inside the exit
housing, not on the faceplate
6” [15.1cm]
13-3/8” [34cm]
POwer consumption and unit rating
Model
Exit Sign Module
SM28-6V
SM44-6V
SM72-6V
SM36-12V
SM72-12V
AC Specs
120/347VAC
less than 1.5W
0.15/0.05 A
0.15/0.05 A
0.15/0.05 A
less than 5W
less than 5W
30min
28
44
72
36
72
Wattage Capacity
1h00
1h30
2h00
16
26
42
21
42
12
18
30
15
30
9
15
24
12
24
4h00
7
12
6
12
ordering information
series
SM28= 6V-28W
SM44= 6V-44W
SM72= 6V-72W
SM36 = 1
2V-36W
SM72 = 1
2V-72W
# of heads
head style and wattage
Blank= no head
-1= one head
-2= two heads
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
RT9= mini tungsten, 9W
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
series
-NEXTN
voltage
Colour
Blank= 120/347Vac,
6VDC
LO62= 277Vac, 6VDC
L12U= 120/347Vac,
12VDC
L122= 277Vac, 12VDC
Blank= factory
white
-BK= black
-GY= grey*
options
Blank= no options
AD= auto-diagnostics*
ADN= auto-diagnostics, non-audible*
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
D3= time delay (15 mins.)
-G= green legend
TP= tamper-proof screws**
*Not available with 6V-72W
*Not all options available with NEXUS® System.
Please consult your sales representative
Other Styles available consult your
sales representative
*Black heads
EXAMPLE: SM28-2RT9-NEXTN
47
**990.0119-RL= Tamper-proof bit (sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
r-SN Series
All Metal “Sortie”
Combination Unit
Features
• Pre-assembled for ease of installation
• M
etal housing with baked enamel finish
– will not yellow
• Easy access to wiring entry
• Exit Sign with long life, ALINGAP LED
light source
• Energy efficient, consumes less than
3W in stand-by mode
• Power pack comes standard with
premium Lead-Calcium battery
• Other colours and options are available
upon request
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Supply and install the Ready-Lite® R-SN Series LED “SORTIE’’ Exit Sign with power pack series. The exit housing
and the faceplate(s) shall be constructed of steel. The Exit Sign shall have a maximum depth of 2-1/2”. The
faceplate(s) shall come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). Red LED technology shall be ALINGAP. The LED lamps
shall provide illumination in normal and emergency operation and shall be mounted inside the exit housing,
not on the face. An LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4”
stroke letters with even illumination. The power pack shall be a completely self-contained emergency unit with
its own charger and rechargeable battery. The housing shall be made of steel. The unit shall be designed to
furnish exit illumination from the normal AC source. When a power failure occurs, the mounted heads along
with the Exit Sign are illuminated in emergency mode for a minimum of 30 minutes. The power pack shall be
furnished with a test switch and high charge pilot light. The heads shall require no tools to adjust and aim. The
heads will be constructed of durable thermoplastic and use 6V, 9W lamps or as otherwise specified.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Ready-Lite® Model:
Wire guards
460.0078-RL
wall mount
460.0060-RL
ceiling mount
POwer consumption and unit rating
Model
AC Specs
30min
Wattage Capacity
1h00
1h30
2h00
4h00
Sortie Sign Module
less than 2W
-
-
-
-
R27= 6V-27W
0.25/0.08 A
27
15
12
9
-
0.25/0.08 A
50
30
20
16
8
12R50= 12V-50W
0.25/0.08 A
50
30
20
16
8
12R80= 12V-80W
0.25/0.08 A
80
45
36
27
12
R50= 6V-50W
120/347VAC
48
-
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
4-5/8” [11.7cm]
12-1/4” [31.2cm]
11” [28.0cm]
All Metal “Sortie”
Combination Unit
7-3/8” [18.7cm]
13-3/8” [31.2cm]
12-1/4” [31.2cm]
6-1/2” [16.6cm]
r-SN Series
4-5/8” [11.7cm]
19-1/8” [48.5cm]
6-3/8” [16.2cm]
18” [45.7cm]
ordering information
Series
# of heads
R27= 6V-27W
R50= 6V-50W
12R50= 1
2V-50W
12R80= 1
2V-80W
Blank= no
heads
1= one head
2= two heads
head style and wattage
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
M6= MR16 halogen, 6V-6W
M10= MR16 halogen, 6V-10W
M12= MR16 halogen, 12V-12W
M20= MR16 halogen, 12V-20W
T9= mini tungsten, 9W
Q8= mini halogen, 8W
Q12= mini halogen, 12W
mounting
faces
S1= single face,
wall or ceiling
mount
SN= universal
steel mount
canopy
with two
faceplates
Other Styles available consult your sales
representative
voltage
housing colour
Blank= 120/347VAC
Blank= factory
white
BK= black
TG= textured grey*
* Black heads
EXAMPLE: R272T9S1
49
options
Blank= no options
TP= tamper-proof screws*
D1= time delay (5 mins.)
D2= time delay (10 mins.)
D3= time delay (15 mins.)
*990.0119-RL= Tamper-proof bit
(sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
• Standard 120/347Vac input
• Wide range of lamp heads available
• Solid-state pulse-type charger standard
• Sealed dust-proof transfer relay
• Auto-diagnostic charger available
(110W only)
• Meets or exceeds CSA 22.2 No. 141.
Wire guards
460.0081-RL
wall mount 110W and 144W
460.0034-RL
wall mount 250W and 360W
Dimensions
Dimensions are approximate and subject to change.
exit
16-1/8” [41 cm] up to 144W
23-1/8 [59 cm] 250W and 360 W
16-1/8” [41 cm]
Features
13-7/8” [35.3 cm]
High Capacity Combination Unit
10-1/4” [26 cm]
LD12E Series
Supply and install the Ready-Lite® LD12E Series “Exit” a unit that combines an illuminated LED Exit Sign
with an emergency light battery unit. The housing and faceplate shall be constructed of steel. The faceplate
shall come standard with knockout chevrons. The light source for the Exit Sign shall be LED. The LED
lamps shall provide illumination in normal and emergency operation. Red LEDs shall be of ALINGAP
technology. The charger board, the battery and the LEDs shall be contained in a single housing. A diffuser
optimized for LEDs shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with
even illumination. The unit shall include a test switch and high charge pilot light. The equipment shall be
designed to furnish exit illumination from the normal AC source. When a power failure occurs, the Exit
Sign along with the emergency heads shall illuminate for a minimum of 30 minutes. The power available
for emergency lights shall be at least 110W or as otherwise specified. The heads shall require no tools to
aim and shall be as specified. The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
.
5-1/2” [13.8 cm]
5-1/2” [13.8 cm]
POwer consumption and unit rating
Model
AC Specs
Exit Sign Module
LD12110E
LD12144E
LD12250E
LD12360E
120/347VAC
less than 2W
0.25/0.10 A
0.25/0.10 A
0.45/0.15 A
0.45/0.15 A
30min
110
144
250
360
Wattage Capacity
1h00
1h30
2h00
64
84
144
210
45
60
100
150
36
48
83
120
4h00
18
24
42
60
ordering information
powerpack
LD12110= 12V-110W
LD12144= 12V-144W
LD12250= 12V-250W
LD12360= 12V-360W
Size B cab 110W or 144W
Size C cab 250W or 360W
options
# of heads
heads style and wattage
Blank= no options
AD= auto-diagnostics
(110W only)
Blank= no heads
1= one head
2= two heads
3= three heads
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
RL12= deco head RL 150, MR16 halogen 12V-12W
RL20= deco head RL 150, MR16 halogen 12V-20W
RL35= deco head RL 150, MR16 halogen 12V-35W
RL50= deco head RL 150, MR16 halogen 12V-50W
LT9= large tungsten, 12V-9W, wedge base
LT18= large tungsten, 12V-18W, wedge base
LT25= large tungsten, 12V-25W, DCB
LH8= large halogen, 12V-8W, sealed beam
LH12= large halogen, 12V-12W, sealed beam
RT9= mini tungsten, 9W
RT18= mini tungsten, 12V-18W, wedge base
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
LQ8= large halogen, 12V-8W, bi-pin
LQ12= large halogen, 12V-12W, bi-pin
LQ20= large halogen, 12V-20W, bi-pin
LQ55= large halogen, 12V-55W, bi-pin
LS12= large tungsten, 12V-12W, sealed beam
LS18= large tungsten, 12V-18W, sealed beam
LS25= large tungsten, 12V-25W, sealed beam
EXAMPLE: LD121102RT9E
50
sign series
E= exit
voltage
Blank=
120/347Vac
U277= 277Vac
colour
Blank= factory
white
B= black
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® LD12S Series LED “SORTIE’’ combo unit. The housing and faceplate shall
be constructed of steel. The faceplate shall come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). The LED lamps shall provide illumination in normal and
emergency operation. Red LED technology shall be ALINGAP. The power pack, rechargeable battery and LEDs
shall be contained in a single housing. A diffuser optimized for LEDs shall be mounted behind the legend to
provide the 6” high by 3/4” stroke letters with even illumination. The power pack is furnished with a test switch
and high charge pilot light. The unit shall be designed to provide Exit Sign illumination from the normal AC source.
When a power failure occurs, the mounted heads along with the Exit Sign are illuminated in emergency mode for
a minimum of 30 minutes. The power available for emergency lights shall be 110W or as otherwise specified. The
heads shall require no tools to adjust and aim. The heads will be constructed of durable thermoplastic and use
9W lamps or as otherwise specified. The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
Wire guards
460.0034-RL
Dimensions
Dimensions are approximate and subject to change.
10-1/4” [26.1 cm]
13-7/8” [35.4 cm]
16-1/8” [41.1 cm]
Cabinet C
5-1/2”
[13.8 cm]
5-1/2”
[13.8 cm]
POwer consumption and unit ratinG
Model
Sortie Sign Module
LD12110S
LD12144S
LD12250S
LD12360S
AC Specs
120/347VAC
30min
less than 2W
0.25/0.10 A
0.25/0.10 A
0.45/0.15 A
0.45/0.15 A
110
144
250
360
Wattage Capacity
1h00
1h30
2h00
64
84
144
210
45
60
100
150
High Capacity Combination Unit
Features
• Standard 120/347Vac input
• Selection of lamp head styles
• Solid state pulse type charger standard
• Sealed dust-proof transfer relay
• Optional self-diagnostic charger
(110W only)
• Available in 12V, 110, 144, 250 and
360W
• Long life, maintenance free lead acid
battery
• Fully C860 approved “SORTIE” legend
illuminated with ALINGAP LEDs and
meets or exceeds CSA 22.2 No. 141.
• High-quality steel enclosure with
corrosion-resistant undercoating
wall mount
23-1/8” [58.8 cm]
LD12S Series
36
48
83
120
4h00
18
24
42
60
ordering information
Series, voltage
and wattage
LD12110= 12V-110W
LD12144= 12V-144W
LD12250= 12V-250W
LD12360= 12V-360W
options
# of heads
Blank= no options
AD= auto-diagnostics
(110W only)
Blank= no heads
1= o ne head
2= two heads
3= three heads
heads style and wattage
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
RL12= deco head RL 150, MR16 halogen 12V-12W
RL20= deco head RL 150, MR16 halogen 12V-20W
RL35= deco head RL 150, MR16 halogen 12V-35W
RL50= deco head RL 150, MR16 halogen 12V-50W
LT9= large tungsten, 12V-9W, wedge base
LT18= large tungsten, 12V-18W, wedge base
LT25= large tungsten, 12V-25W, DCB
LH8= large halogen, 12V-8W, sealed beam
LH12= large halogen, 12V-12W, sealed beam
RT9= mini tungsten, 9W
RT18= mini tungsten, 12V-18W, wedge base
RQ8= mini halogen, 8W
RQ12= mini halogen, 12W
LQ8= large halogen, 12V-8W, bi-pin
LQ12= large halogen, 12V-12W, bi-pin
LQ20= large halogen, 12V-20W, bi-pin
LQ55= large halogen, 12V-55W, bi-pin
LS12= large tungsten, 12V-12W, sealed beam
LS18= large tungsten, 12V-18W, sealed beam
LS25= large tungsten, 12V-25W, sealed beam
EXAMPLE: LD121102RT9S
51
lettering
S= sortie
voltage
colour
Blank= 120/347Vac
U277= 277Vac
Blank= factory
white
B= black
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RP Series
All-Plastic Pictogram Exit Sign
Commercial-grade,
universal-mount and snap-fit
Supply and install the Ready-Lite® RP pictogram Exit Sign. The equipment shall operate with universal 2-wire
AC input voltage of 120 to 347VAC at less than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC
at 1W consumption for single and double face signs. The sign shall come standard with a canopy and shall
be suitable for wall, end, or ceiling mounting. The frame, faceplates, back plate and canopy shall each be
constructed of a one-piece UV-stabilized thermoplastic material coloured factory white. The light source shall be
white light-emitting diodes (LED) and shall provide even illumination in normal and emergency operation. The
equipment in a Self-powered configuration shall use a sealed Nickel-Cadmium battery of 2.4V nominal voltage.
The equipment shall recharge the battery in 24 hours and stay illuminated at least two hours upon AC failure.
The pictogram Exit Sign shall be listed to the CSA 22.2 No.141-10 standard.
The equipment shall be Ready-Lite® Model: ____________________________________________________ .
Dimensions are approximate and subject to change.
4-1/2” [11.4 cm]
8-7/8” [22.5 cm]
• Durable factory white, thermoplastic
housing
• Universal mounting: wall-, end-, or
ceiling-mount
• Long-life white LED light source
• Certified CSA 22.2 No.141-10 for
pictogram safety signs
• Two-wire universal AC input: 120 to
347VAC; two-wire standard DC input:
6 to 24VDC
• Energy efficient – consumes less than
2.5W in AC mode and only 1W in
DC-remote
• Self-powered model delivers standard
two hours of back-up lighting
• Optional vandal-proof shield and
tamper-proof screws
Dimensions
8” [20.3 cm]
The Ready-Lite® RP Series is a compact
pictogram Exit Sign with an all-in-one,
snap-fit design. Easy to install and
affordable, the RP Series Exit Sign is
ideally suited for commercial applications,
especially those in which large numbers
of Exit Signs are required.
6-1/8” [15.6 cm]
Features
12-1/8” [30.7 cm]
2-1/4” [5.7 cm]
13” [33.0 cm]
POwer consumption and unit rating
Model
AC Specs
AC only
AC/DC standard
AC/Special DC
DC SPECS
120 to 347VAC
120 to 347VAC
120 to 347VAC
less than 2.5W
less than 2.5W
less than 2.5W
6 to 24VDC
36, 48, 120VDC
less than 1.5W
less than 2.5W
Two-wire 120V AC/DC
120Vac
self-powered
120 to 347VAC
less than 2.5W
120VDC
less than 2.5W
less than 3W
nickel-cadmium battery
min. 2 hours
ordering information
Series
RP= plastic pictogram
faces/mounting
1= single face, universal mounting
2= d
ouble face, universal mounting
3= u
niversal face, universal mounting
enclosure
colour
voltage
W= factory white
B= black
SP= self-powered, 120 to 347vac
U= universal 120 to 347Vac; 6 to 24Vdc
U00= 120 to 347Vac only
U36= 120 to 347Vac; 36Vdc
U48= 120 to 347Vac; 48Vdc
U120= 120 to 347Vac; 120Vdc
24= 2-wire 6 to 24Vdc
2120= 2-wire 120Vac/Vdc
options
TP= tamper-proof screws*
VR= vandal resistant shield with
tamper-proof screws*
*990.0119-RL= T
amper-proof bit
(sold separately)
* Not available with universal face
E xample : R P 1 W U V R
Unlike EXIT signs, the pictogram sign is not available in double arrow configurations.
52
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® Ultima™ Series Exit Sign. The standard equipment shall operate with a
dual-voltage input of 120/347VAC with less than 2W of consumption and a universal two-wire DC input
voltage from 6VDC to 48VDC at less than 2.5W for single and double face signs. The exit shall be suitable
for wall, end, or ceiling mount. The faceplate shall be constructed of durable high impact thermoplastic. No screws are necessary to hold the faceplate or the back plate to the housing. The faceplates shall
come standard with snap in/out chevrons. The frame shall consist of one-piece factory white thermoplastic. The light source shall be light emitting diodes (LEDs). The LEDs shall provide illumination in normal
and emergency operation and shall be mounted inside the exit housing. Red LED technology shall be
ALINGAP. An LED-sensitive diffuser shall be mounted in front of the LEDs to provide the 6” high by ¾”
stroke letters with even illumination. The Exit Sign shall be C860 approved.The Exit Sign in a Self-powered configuration shall be equipped with a sealed, maintenance-free Nickel-Cadmium battery. The
equipment shall recharge the battery in 24 hours and stay illuminated at least 90 minutes upon AC failure.
The Self-powered model equipped with advanced diagnostic shall self-test by simulating a power failure for
one minute every 30 days, 30 minutes every 60 days and 90 minutes every 360 days. A diagnostic circuit
shall continuously monitor the performance of the battery, charger module and LED lamps. Upon failure
detection the system shall display the error on the AC pilot lamp, which will change color from green to
red and will flash with a specific code. The red light shall be steady-on in case of “Battery Disconnect”;
it shall flash with one blink for “Battery failure”, two blinks for “Charger failure” and four blinks for “LED
lamp failure. A label with the diagnostic legend shall be visible next to the pilot light. CSA-C860 Approved.
The equipment shall be Ready-Lite® Model:
.
u l t i m a ™ fa m i ly
Ultima™ Combo P. 56-57
Ultima™ Battery P. 122-123
Wire guards
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
8” [20.3 cm]
9” [22.9 cm]
Dimensions are approximate and subject to change.
ultima™ Series
Thermoplastic Exit Sign
Features
• Durable, injection-molded,
thermoplastic housing
• Long-life, energy-efficient ALINGAP LED
light source
• Universal mounting - supplied standard
with two stencil plates, red diffusing
lens and backplate
• Universal, field-selectable snap in/out
chevrons
• Available for wall, end or ceiling
mounting
• Energy efficient – consumes less than
3.5W
• Normal AC and emergency DC
operation with dual AC input of
120V/347V and universal DC input of
6V to 48V
• Comes with the Ready-Lite® EZ2 canopy
for quick and easy installation – see
page 94 for more information
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
2” [5.0 cm]
11-7/8” [30.1 cm]
12-7/8” [32.8 cm]
POwer consumption and unit rating
AC Specs
Model
DC SPECS
AC only
AC/DC remote
self-powered
120/347VAC
120/347VAC
120/347VAC
less than 2.5W
less than 2W
less than 3.5W
6 to 48VDC
nickel-cadmium battery
less than 1.5W
minimum 90 minutes
self-powewed with diagnostic
120/347VAC
less than 3W
nickel-cadmium battery
minimum 90 minutes
ordering information
Series
ULT= LED plastic
universal exit
Colour
W= factory
white
B= black
Unit capacity
AC= AC only
AC2C1= dual AC circuit (2X 120V)
UD= 120/277 or 120/347Vac & 6 to 48Vdc
SPN= self-powered NiCad, 120/347VAC
SDN= s elf-powered diagnostic NiCad,
120/347VAC
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
voltage
2= 120/277VAC
3= 120/347VAC
Legend colour
R= red
G= g reen
R1= red single face*
R2= red double face*
G1= g reen single face*
G2= g reen double face*
*Specify number of faces
for options
*Self-powered models only
E X A M P L E : U LT W A C 3 R
53
options
TP= tamper-proof screws*
VRTP= p
olycarbonate shield with tamperproof screws*
BA= brushed aluminum stencil
*990.0119-RL= T
amper-proof bit (sold separately)
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
RCS Series
2-3/16” [5.5cm]
Plastic Pictogram Exit Sign
13-5/8” [34.5cm]
< Picto
left from here
Picto straight
from here
Picto >
Right from here
POwer consumption and unit rating
Model
AC/DC-remote
self-powered
AC Specs
120/347VAC
0.5/0.4 A
DC Specs
4.2/3.6W
6 to 24VDC
less than 1.5W
Ni-Cd battery
min. 90 minutes
R S C fa m i ly
RCSC Combo P. 55
ordering information
RCSB Battery P. 117
Series
RCS
9-1/16” [23cm]
• Energy efficient, long-life white LEDs
consuming 4.2W at normal operation
• Dual voltage input capability
120/347VAC
• Selection of AC/DC, 6 to 24VDC
or self-powered using a 3.6V
Nickel-Cadmium battery
• Automatic, temperature
compensated, pulse type charger
• Low voltage disconnect prevents
over discharge of battery
• Automatic brownout protection
• Battery lock-out prevents
discharge during installation
• Comes standard with three pictogram
legends for direction selection
• Red LED charger monitor
• Injection-molded off-white
thermoplastic ABS housing
• Fast and easy installation with
snap-together design
• Ceiling, wall or end mount installation
• CSA C22.2 no.141-10 listed
• Comes standard with one (1)
year warranty
5-15/16” [15cm]
Features
RCSR Remote P. 148
voltage
-U= 120/347VAC, 6 to 24VDC
-ISP= 120/347VAC, self-powered (90 mins.)
E xample : R C S - I S P
54
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
RCSC Series
11-3/8” [28.9cm]
Plastic Pictogram Exit
Combo Unit
5-15/16” [15cm]
9-1/16” [23cm]
2-3/16” [5.5cm]
13-5/8” [34.5cm]
< Picto
left from here
Picto straight
from here
Picto >
Right from here
POwer consumption and unit rating
Model
RCSC-2LEDWR
AC Specs
120/347VAC
DC Specs
0.5/0.4 A
4.2/3.6W
Ni-Cd battery
R S C fa m i ly
RSC Exit P. 54
RCSB Battery P. 117
min. 90 minutes
Features
• Energy efficient, long-life white LEDs
consuming 4.2W at normal operation
• Dual voltage input capability
120/347VAC
• 3.6V Nickel-Cadmium battery provides
minimum 90 minutes of emergency
lighting
• Fully adjustable LED glare-free lens
• 3.6V 1W long life LED light source,
6000K
• Adjustable light heads for forward or
backward lighting
• Automatic, temperature compensated,
pulse type charger
• Low voltage disconnect prevents over
discharge of battery
• Automatic brownout protection
• Battery lock-out prevents discharge
during installation
• Comes standard with three pictogram
legends for direction selection
• Red LED charger monitor
• Injection-molded off-white
thermoplastic ABS housing
• Fast and easy installation with
snap-together design
• Ceiling, wall or end mount installation
• CSA C22.2 no.141-10 listed
• Comes standard with one (1) year
warranty
RSCR Remote P. 148
ordering information
Series
RCSC
voltage
Blank= 120/347VAC
lamp
-2LEDWR= 2X 1W LED
E xample : R C S C
55
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
ultima™ Series
Thermoplastic
Combination Unit
Features
The Ultima™ Series of combination units
(emergency light battery unit with an Exit
Sign) are designed with aesthetics, ease of
installation and performance in mind.
• One-pack combination of battery unit
and Exit Sign, a compact and
contemporary design
• Durable injection-molded thermoplastic
housing with push-to-snap design
• Available in single or double face
configurations both with means for
ceiling mounting
®
™
• C omes with the Ready-Lite Ultima
EZ2 canopy and field-selectable snap
chevrons for quick and easy installation
• E xit Sign module illuminated by long-life
ALINGAP red LEDs
• Two MR16 halogen lamps, shielded by
a clear polycarbonate cover
• Optional MR16 LED lamps with life
expectancy 50,000+ hours
• Sealed, maintenance-free, LeadCalcium or Nickel-Metal-Hydride
batteries
• Remote load capacity up to 90W
• Dual voltage input: 120/347VAC or
120/277VAC.
• Optional vandal-resistant shield with
tamper-proof screws
• Certified CSA C22.2 No.141
• Optional advance diagnostics circuitry
available
Supply and install the Ready-Lite® Ultima™ Series combination emergency light battery unit and Exit Sign.
The standard equipment shall operate with a dual voltage input of 120/347VAC. The unit shall be suitable for
wall or ceiling mount. The unit frame and face plates shall be made of injection-molded durable high-impact
thermoplastic and come standard with snap in/out chevrons. No screws are necessary to hold the faceplate
or backplate to the housing. The one-piece thermoplastic frame is molded in white (optional black). The
faceplates shall feature a uniformly illuminated legend.
The light source shall be light emitting diodes (LED) and shall provide illumination in normal and emergency
operation and shall be mounted inside the combination housing. Red LED technology shall be ALINGAP. An
LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with
even illumination. The unit shall be equipped with two emergency heads with tool-less adjustable swivels
(lamps of 12W or less) and long-life MR-16 type lamps of ___ V and ___ W. Each lamp shall be protected by
a snap-on, shock-absorbent, transparent polycarbonate cover.
The unit shall be equipped with a test switch and a green pilot light, located on the face plate above the EXIT
legend. The battery charger shall be driven by a micro-controller. All electronic circuitry (charger, LED driver,
LED’s) shall be installed on a single printed circuit board PCB. The unit equipped with self-testing / selfdiagnostic features shall automatically self test for one minute every 30 days, 10 minutes in the 6th month
and 30 minutes annually. When a fault is detected, the bi-colour pilot light shall turn from green to red and
shall flash, identifying the source of the failure: battery, charger circuitry, lamp load, LED strip.
The Exit Sign module shall be CSA-C860 approved.
.
The combo unit shall be Ready-Lite® Model:
u l t i m a ™ fa m i ly
Ultima™ Exit P. 53
Ultima™ Battery P. 122-123
Wire guards
460.0078-RL
wall mount
POwer consumption
Model
AC Specs
Exit Sign Module
less than 2W
L20
L50
12L50
0.11/0.04 A
120/347VAC
12H5
0.22/0.08 A
12H10
56
30min
Wattage Capacity
1h00
1h30
2h00
4h00
-
-
-
-
-
20
15
12
8
-
50
30
24
16
8
50
30
24
16
8
50
36
24
18
9
100
72
48
36
18
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Dimensions
Dimensions are approximate and subject to change.
4-7/8” [12.3 cm]
ultima™ Series
11-1/4” [28.7 cm]
12-3/8” [31.5 cm]
Thermoplastic
Combination Unit
17” [43.2 cm]
3-3/8” [8.6 cm]
ordering information
powerpack
# of heads
head style/ wattage
faces/mounting
voltage
colour
legend
L20= 6
V-20W
lead cal
L50= 6
V-50W
lead cal
12L50= 1
2V-50W
lead cal
12H5= 12V-50W
NiMH
12H10= 12V-100W
NiMH
Blank= n
o
heads
-2= two
heads
LD1= M
R16 LED, 6V-4W
LD7= M
R16 LED, 12V-4W
LD9= M
R16 LED, 12V-5W
LD10= M
R16 LED,
12V-6W
M6= MR16 halogen,
6V-6W
M10= MR16 halogen,
6V-10W or 12V-10W
M12= MR16 halogen,
12V-12W
M20= MR16 halogen,
12V-20W
-ULT1= s ingle face
ceiling or
wall mount
-ULT2= d
ouble
face ceiling
mount
-ULT1N= s ingle face
wall mount
(less
canopy)
-ULTU= u
niversal,
2 faces
backplate
and canopy
3= 120/347VAC
2= 120/277VAC
W=
factory
white
B=
black
Blank= red
legend
G=g reen
legend
options
Blank= no options
AD= auto-diagnostics
ADN= auto-diagnostics, non-audible
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
BA= brushed aluminum exit stencil
D3= time delay (15 mins.)
TP= tamper-proof screws**
VRTP1= p
olycarbonate shield with
tamper-proof screws, single face**
VRTP2= p
olycarbonate shield with
tamper-proof screws, double face**
*Not all options available with NEXUS® System.
Please consult your sales representative
**990.0119-RL= T
amper-proof bit (sold separately)
E X A M P L E : L 2 0 - 2 M 6 - U LT 1 3 W
57
Type:
Project/Location:
Contractor:
Prepared By:
Made in Canada
NEMA-3R
Date:
Model No.:
Typical specifications
• Units are certified NEMA-3R
• Gasketed fiberglass housing designed
specially for industrial applications
• Sealed, vandal-resistant clear
polycarbonate faceplate
• Water, dust and oil resistant, suitable
for high abuse areas, wet locations
• Long life, even illumination of the
legend provided by energy-efficient
ALINGAP technology LED light source
consuming less than 3W per face
• Wall, ceiling or end mount.
• Mounting bracket available for ease
of installation
• Normal AC and emergency DC
operation – 120V to 347Vac and 6V to
24Vdc input
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Wire guards
460.0081-RL
wall mount
460.0104-RL
ceiling mount
460.0124-RL
end mount
Dimensions
Dimensions are approximate and subject to change.
Double face
Features
Single face
NEMA-3R Certified
“Sortie” Sign
12-1/4” [31.1 cm]
CS9000N Series
Supply and install Ready-Lite® CS9000N Series “SORTIE” Exit Signs. The equipment shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than 1.5W and universal two-wire DC input voltage
from 6VDC to 24VDC at less than 1.5W per face.
The sign housing shall be of grey fiberglass, specially designed for industrial environments. The sealed faceplate
shall be gasketed, completely transparent, high abuse and vandal resistant, and will feature an even illuminated legend.
The light source illuminating the legend shall be ALINGAP technology red LEDs. The exit in a Self-powered
configuration shall include a magnetic test switch and a Nickel-Cadmium battery. The Exit Sign shall stay
illuminated during emergency operation for at least 60 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Ready-Lite®Model:
.
19-5/8” [49.8 cm]
2” [4.9 cm]
3-7/8” [9.8 cm]
POwer consumption and unit rating
Model
ordering information
AC Specs
DC Specs
AC/DC standard
120 to 347VAC
less than 1.5W
6 to 24VDC
less than 1.5W
AC/special DC
120/277/ 347VAC
less than 2.5W
36 or 48 or 120VDC
less than 2.5W
self-powered
120 to 347VAC
less than 3W
nickel-cadmium battery
minimum 60 minutes
Note: double face models have double the power consumption above.
Series
CS9100N= sortie, single face, wall, end and ceiling mount
CS9200N= sortie, double face, end or ceiling mount
voltage
UL= 120/277/347VAC, 6/12/24VDC
LI2012W= 120Vac, 120Vdc 2 wires
LU36= 120/277/347Vac - 36Vdc 4 wires
LU48= 120/277/347Vac - 48Vdc 4 wires
LU120= 120/277/347Vac - 120Vdc 4 wires
ISP= self-powered, 120 to 347VAc
EXAMPLE: CS9100NUL
Special wording available. see page 87. Please consult your sales representative.
58
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-3R
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install Ready-Lite® CX9000BIL or CS9000BIL Series Bilingual LED Exit Sign. The equipment
shall operate with universal two-wire AC input voltage from 120VAC to 347VAC at less than 3W per face
and universal two-wire DC input voltage from 6VDC to 24VDC at less than 3W per face. The housing shall
be of gray fiberglass, gasketed, specially designed for industrial environments. The sealed front cover shall
be constructed of heavy-duty vandal-resistant transparent polycarbonate of 4mm thickness and shall be
bent around the back box for increased rigidity. The front cover will feature an even illuminated legend
with the text ”EXIT” and “SORTIE” positioned one on top of the other. The light source shall be the new
ALINGAP technology red LED. The equipment shall be suitable for wall or ceiling mount and be designed specifically for high abuse areas, wet locations, dust and oil-tight applications. The equipment in a Self-powered
configuration shall stay illuminated during emergency operation for at least 60 minutes upon AC failure.
The equipment shall be NEMA-3R and C-860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
.
wall mount
460.0104-RL
ceiling mount
NEMA-3R Certified Bilingual Sign
Features
• Certified NEMA-3R
• Gasketed fiberglass housing designed
specifically for industrial applications
• Grey finish
• Sealed, vandal-resistant polycarbonate
faceplate
• Wall or ceiling mounting; wall or ceiling
brackets available for easy installation
• Normal AC and emergency DC
operation – 120 to 347V AC input; 6 to
24 DC input
Wire guards
460.0034-RL
CX9000BIL &
CS9000BIL Series
Dimensions
Dimensions are approximate and subject to change.
24-1/8” [61.4 cm]
15” [38.1 cm]
Double face
Single face
15” [38.1 cm]
• Meets or exceeds CSA 22.2 No. 141.
2” [4.9 cm]
24-1/8” [61.4 cm]
3-7/8” [9.8 cm]
POwer consumption and unit rating
Model
AC Specs
DC Specs
AC/DC
120 to 347VAC
less than 3W
6 to 24VDC
less than 3W
self-powered
120 to 347VAC
less than 5W
nickel-cadmium battery
minimum 60 minutes
Note: double face models have double the power consumption above.
ordering information
Series
CX9100N= single face NEMA 3R, exit over sortie
CS9100N= single face NEMA 3R, sortie over exit
CX9200N= double face NEMA 3R, exit over sortie
CS9200N= double face NEMA 3R, sortie over exit
EXAMPLE: CX9100N-UL2
voltage
-UL= 120 to 347Vac, 6 to 24Vdc
-ISP= self-powered, 120 to 347Vac
BIL
59
lettering
BIL= bilingual
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-3R
Date:
Model No.:
Made in Canada
Typical specifications
LD6-IF Series
NEMA-3R Certified
Combination Unit
Features
• This unit is ideal for schools, parking
garages, public places, transit platforms
and security areas such as jails
• Units are NEMA-3R cerfified
• Gasketed fiberglass housing designed
specially for industrial applications
• Sealed, vandal-resistant clear
polycarbonate faceplate
• Fully integrated unit with charger and
rechargeable battery
• Water and snow resistant, suitable for
areas subject to vandalism and wet
locations
• Solid state charger circuitry – capable
of full recharge within 24 hours
• Low voltage disconnect circuitry
• Sealed, dust-tight transfer relay
• Exit light source is ALINGAP
technology LED
• Power pack includes a magnetic test
switch and a high charge pilot light
• In emergency mode, the long life,
sealed nickel cadmium battery provides
power to the Exit Sign and lamp
heads for a minimum of 30 minutes
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
Supply and install Ready-Lite® LD6-IF Series industrial combo unit. The unit shall be fabricated of industrial grade
polycarbonate designed specifically for industrial environments. The sealed front cover shall be fabricated of
high abuse and vandal-resistant polycarbonate, and feature an evenly illuminated legend. The word “SORTIE”
shall be illuminated by long life LEDs consuming less than 1.5W per face.
The light source shall be ALINGAP technology red LED. The Exit Sign shall be certified NEMA-3R and designed
specifically for applications such as high abuse areas, wet locations, environments requiring dust and oil tight
equipment or cold temperatures.
It shall be designed to provide normal AC illumination and upon AC failure, the Exit Sign and lamp heads shall
stay illuminated in emergency mode for a minimum of 30 minutes. The power pack is supplied with a magnetic
test switch and a high charge pilot light.
The combo unit shall be CSA-C860 and NEMA-3R certified and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® model: _____________________________________________________.
Wire guards
460.0034-RL
wall mount
460.0104-RL
ceiling mount
460.0124-RL
double face, end mount
pOWER CONSUMPTION AND unit rating
Model
LD6-36
LD6-72
AC Specs
120/347VAC
1h00
1h30
2h00
0.15/0.06 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
Note: double face models have double the power consumption above
60
Wattage capacity
30min
4h00
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-3R
Date:
Model No.:
Made in Canada
Dimensions
Dimensions are approximate and subject to change.
7-5/16”
[18.6 cm]
LD6-IF Series
9-5/16” [23.6 cm]
12-1/4” [31.1 cm]
12-13/16” [32.5 cm]
NEMA-3R Certified
Combination Unit
2” [4.9 cm]
19-5/8” [49.8 cm]
Single face
3-7/8” [9.8 cm]
Double face
ordering information
Series
LD6-36IF= 6
V-36W, sortie, single face
LD6-36IF2= 6
V-36W, sortie, double face
LD6-72IF= 6
V-72W, sortie, single face
LD6-72IF2= 6
V-72W, sortie, double face
voltage
UL= 120/347VAC
Number of heads
Blank= no heads
1= one head
2= two heads
EXAMPLE: LD6-36IFUL2WT9
61
lamp type and wattage
WT9= tungsten, 6V-9W
WT18= tungsten, 6V-18W
WT25= tungsten, 6V-25W
WQ8= halogen, 6V-8W
WQ12= halogen, 6V-12W
WQ20= halogen, 6V-20W
WH8= halogen, 6V-8W, sealed beam
WH12= halogen, 6V-12W, sealed beam
WH20= halogen, 6V-20W, sealed beam
WS8= tungsten, 6V-8W, sealed beam
WS18= tungsten, 6V- 18W, sealed beam
WS25= tungsten, 6V-25W, sealed beam
Options
TC= teflon coated
lens
Type:
new product
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Made in Canada
Model No.:
Typical specifications
RN Series
NEMA-4X & NSF Certified
Pictogram Sign
Features
• N
EMA-4X Certified
• NSF compliant for food processing
• Polymeric enclosure is fully gasketed
around lens and canopy to secure
against water leaks
• S
ealed, heavy-duty, vandal-resistant
polycarbonate face plate
• Suitable for cold weather: -40°C for AC/
DC and -20°C for Self-powered models
(option: -CW)
• Tamper-resistant, concealed test switch
with magnetic action
• White LED light source
• Supplied standard with two pictogram
films per face, for direction selection
• Meets or exceeds CSA 22.2 No.141-10
standard for pictogram Exit Signs
• U
niversal AC input: two-wire 120 to
347Vac; Standard DC input: two-wire
6 to 24Vdc
• Energy efficient – consumes less than
2.5W in AC or DC-remote mode
• S
elf-powered models deliver two hours
of back-up lighting
Supply and install the Ready-Lite® RN Series pictogram Exit Signs. The equipment shall be certified for NEMA4X and designed specifically for high abuse areas, wet locations, and cold weather applications. The equipment
frame shall be of industrial grade polyvinyl chloride with a gasket around lenses and canopy. The faceplate(s)
shall be constructed of heavy-duty vandal-resistant polycarbonate and feature an even illuminated legend.
Each face plate shall come standard with two legend films for pictogram and direction selection. The light
source shall be white light-emitting diodes (LED). The pictogram Exit Sign shall operate with universal 2-wire
AC input voltage of 120 to 347VAC at less than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC
at less than 1W for single and double face signs. The Self-powered model shall include a concealed green
pilot light and magnet-sensitive test switch, shall use a sealed Nickel-Cadmium battery of 2.4V nominal voltage
and shall stay illuminated during emergency operation for at least two hours upon AC failure. When specified,
the Self-powered model shall include auto-test functions: it shall execute automatic tests for 5 minutes every
30 days, 30 minutes every 60 days and two hours annually. When a fault is detected, the bi-colour pilot light
shall turn from green to red and flash following a particular code. The code description shall be visible on a
label next to the pilot light to identify the failure type: battery, charger circuitry, or LED lamps.
The pictogram Exit Sign shall be listed CSA 22.2 No.141-10 standard.
The equipment shall be Ready-Lite® Model:
n e m a - 4 x a n d n s f c e r t i f i ed fa m i ly
RNC Combo P. 64-65
TUF Exit P. 63
N-TUF Combo P. 66-67
TUF-NM Battery P. 128-129
TUF-NM Remote P. 160-161
Wire guards
460.0079-RL
460.0027-RL
460.0028-RL
wall mount
end mount
ceiling mount
POwer consumption and unit rating
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
less than 2.5W
-
-
AC/DC standard
120 to 347VAC
less than 2.5W
6 to 24VDC
less than 1W
AC/Special DC
120 to 347VAC
less than 2.5W
36, 48, 120VDC
less than 2.5W
Two-wire 120V AC/DC
120VAC
less than 2.5W
120VDC
less than 2.5W
Self-powered
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 2 hours
Self diagnostic
120 / 347VAC
less than 3.5W
nickel-cadmium battery
min. 2 hours
Dimensions
Dimensions are approximate and subject to change.
13-1/4” [33.6 cm]
14” [35.7 cm]
9-1/4” [23.4 cm]
3-7/8” [9.9 cm]
Double
Face
3-1/2” [8.7 cm]
Single
Face
< Pictogram
Left from here
Pictogram
Straight from
here
Pictogram >
Right from here
ordering information
Series
FaceS/ Mounting
colour
RN= NEMA-4X &
NSF pictogram
exit sign
1= s ingle face universal
mounting
2= d
ouble face
universal mounting
W= factory
white
B= black
Voltage
SP= self-powered, 120 to 347VAC
SPD= self-powered diagnostic NiCad, 120/347VAC
SPD2= self-powered diagnostic NiCad, 120/277VAC
U= universal 120 to 347Vac; 6 to 24Vdc
U00= 120 to 347Vac only
U36= 120 to 347Vac; 36Vdc
U48= 120 to 347Vac; 48Vdc
U120= 120 to 347Vac; 120Vdc
2120= 2-wires 120Vac/Vdc
NEX= NEXUS® system interface, 120/347VAC
NEX2= NEXUS® system interface, 120/277VAC
NEXRF= NEXUS® system interface, 120/347VAC
NEXRF2= NEXUS® system interface, 120/277VAC
EXAMPLE: RN1BSPCW
62
Options
CW= cold-weather (-20°C
for self-powered and
NEXUS® only)
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Made in Canada
Model No.:
Typical specifications
Supply and install Ready-Lite® TUF Series LED Exit Signs. The equipment shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than 3W and universal two-wire DC input
voltage from 6VDC to 48VDC at less than 2W for single and double face signs. The equipment frame
shall be of industrial grade polyvinyl chloride with a gasket around lenses and canopy designed
specifically for hostile environments. The faceplate(s) shall be constructed of heavy-duty vandal-resistant
polycarbonate and feature an even illuminated legend. The light source shall be light emitting diodes (LED).
Red LED technology shall be ALINGAP. An LED-sensitive diffuser shall be mounted behind the legend to provide
the 6” high by 3/4” stroke letters with even illumination. The exit shall be certified for NEMA- 4X and designed
specifically for high abuse areas, wet locations, and cold weather -20°C (-4°F) applications.
The Self-powered model shall stay illuminated during emergency operation for at least 90 minutes upon AC
failure and shall include a magnetic test switch and self-testing and self-diagnostic functions. The equipment
shall automatically self test for 5 minutes every 30 days, 30 minutes every 60 days and 90 minutes annually.
A “Service Required” lamp shall be located near the test switch and flash when a fault is detected. A two-LED
diagnostic display shall be located inside the equipment and shall identify the eventual source of failure
(battery, charger circuitry, or LED lamps).
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
.
n e m a - 4 x a n d n s f c e r t i f i ed fa m i ly
RNC Combo P. 64-65
RN P. 62
N-TUF Combo P. 66-67
TUF-NM Battery P. 128-129
TUF-NM Remote P. 160-161
Wire guards
460.0079-RL
wall mount
460.0027-RL
end ount
460.0028-RL
ceiling mount
POwer consumption and unit rating
Model
AC Specs
DC Specs
AC/DC red
120 to 347VAC
less than 3W
6 to 48VDC
less than 2W
AC/DC green
120 to 347VAC
less than 3W
6 to 48VDC
less than 2W
Self-powered red
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
Self-powered green
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
TUF Series
Polyvinyl Chloride Exit Sign
Features
• NEMA-4X certified
• NSF certified for food processing
• Polyvinyl chloride enclosure is fully
gasketed around lens and canopy to
prevent water infiltration
• Sealed faceplate of heavy-duty, vandalresistant polycarbonate with evenly
illuminated legend
• Suitable for cold weather: -40°C on non
Self-powered sign and -25°C on
Self-powered (“CW” option)
• Tamper-resistant magnetic test switch
• Self-diagnostic circuitry standard on all
Self-powered models
• Energy efficient – consumes less than
3W in AC or DC mode
• Normal AC and emergency DC
operation – 120 to 347V universal AC
dual tap; 6 to 48V universal DC
®
• NEXUS compatible
• Meets or exceeds CSA 22.2 No. 141.
Dimensions
Dimensions are approximate and subject to change.
14” [35.7 cm]
3-7/8” [9.9 cm]
3-1/2” [8.7 cm]
9-1/4” [23.4 cm]
13-1/4” [33.6 cm]
Double Face
Single Face
ordering information
Series
Faces/mounting
TUF= NEMA-4X -1= single face,
& NSF
universal mount
exit sign
-2= double face,
universal mount
AC voltage
Housing/face
voltage
Blank= 120Vac, (with
L120-2W only)
-U= universal,
120-347Vac
-WH= white/white
-BK= black/black
-BW= black/white
-WB= white/black
-GW= grey/ white
-GB= grey/black
-WA= white/aluminum
-BA= black/aluminum
-GY= grey/grey
-DC= u
niversal 120-347Vac, 6-48Vdc
(-40°C standard)
-SPD= self-powered diagnostic NiCad,
120 to 347VAC
-L120-2W= 120Vac, 120Vdc 2 wires
NEX= NEXUS® system interface
NEXRF= wireless NEXUS® system interface
EXAMPLE: TUF-2-U-WH-DC-G-4X
63
options
Blank= no options
-G= green legend
-CW= cold weather
(-25°C for
self-powered)
4X
-4X = approved
NEMA-4X
and NSF
Type:
new product
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Model No.:
Made in Canada
Typical specifications
RNC Series
NEMA-4X & NSF Certified
Pictogram Combination Unit
Features
• Certified NEMA-4X for wall or ceiling
mount
• NSF certified for use in food processing
areas
• Meets or exceeds CSA 22.2 No.141-10
standard for pictogram Exit Signs
• Polyvinyl chloride frame, with built-in
gasket to prevent water infiltration
• Sealed, vandal-resistant faceplate of
polycarbonate
• Legend illuminated by long-life white
LED’s
• Comes standard with two pictogram films
per face, for direction selection
• Two high-performance MR16 LED
lamps shielded by a clear
polycarbonate cover
• Optional 5W LED emergency lights
provide 60’ of egress illumination on a
6-foot wide path
• Sealed, maintenance-free Lead-Calcium
or Nickel-Cadmium batteries
• Remote load capacity: covers with 4W
LED lights 100’ up to 230’ of egress
illumination
• Comes standard with auto-diagnostic
• Cold-weather option: -40°C (-40°F) with
only 14W extra power consumption
Supply and install Ready-Lite® RNC Series combination emergency light battery unit and pictogram Exit Sign.
Designed specifically for industrial environments, the equipment frame shall be of industrial grade polyvinyl
chloride with gaskets around both sides of frame contour. The back plate shall be made of 1/8” thick aluminum
sheet and shall include knock-outs for installation on an electrical box. The faceplate(s) shall be constructed
of heavy-duty vandal-resistant clear polycarbonate and feature a uniformly illuminated pictogram legend. Each
face plate shall come standard with two legend films for pictogram and direction selection. The light source
shall be long-life white light-emitting diodes (LED).
The unit shall have attached a lower compartment containing two emergency heads with adjustable swivels
and long-life MR-16 LED lamps of ___ V and ___ W. The heads shall be installed on a shield housing made
of rigid thermoplastic and shall be protected by a shock-absorbent, clear polycarbonate cover. The standard
AC input voltage shall be 120/347VAC. The unit shall be equipped with a magnetic test switch and an LED
pilot light protected by the clear face plate.
The unit shall perform auto-test functions managed by a micro-controller and shall automatically self-test for
one minute every 30 days, 10 minutes in the 6th month and 30 minutes annually. When a fault is detected,
the bi-colour pilot light shall turn from green to red and flash following a particular code. The code description
shall be displayed on a label next to the pilot light to identify the failure type: battery, charger circuitry, LED
lights for the signage, or emergency lights.
The combination unit shall meet or exceed the standard CSA C22.2 No.141-10.
The equipment shall be Ready-Lite® Model:
.
n e m a - 4 x a n d n s f c e r t i f i ed fa m i ly
RN P. 62
TUF P. 63
N-TUF Combo P. 66-67
TUF-NM Battery P. 128-129
TUF-NM Remote P. 160-161
Wire guards with heads
460.0078-RL
wall mount
460.0060-RL
end or ceiling mount
Power Consumption
Model
AC Specs
Emergency power for lamps
1h00
1h30
2h00
Pictogram Sign Module
less than 2.5W
-
-
-
-
-
RNC-6N36
0.10/0.03 A
36
30
20
16
8
0.25/0.08 A
36
30
20
16
8
0.18/ 0.06 A
60
40
30
20
10
RNC-6N36-CW
120/347VAC
RNC-12N60
64
30min
4h00
Type:
new product
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Model No.:
Made in Canada
Dimensions
Dimensions are approximate and subject to change.
RNC Series
< Pictogram
Left from here
Pictogram
Straight from here
Pictogram >
Right from here
NEMA-4X & NSF Certified
Pictogram Combination Unit
14” [35.7 cm]
3-1/2” [8.7 cm]
3-7/8” [9.9 cm]
9-1/4” [23.4 cm]
12-5/8” [32.1 cm]
13-1/4” [33.6 cm]
Double Face
Single Face
ordering information
Series
RNC= NEMA-4X &
NSF pictogram
exit combo unit
Faces / Mounting*
1= s ingle face
2= d
ouble face
Housing
colour
Battery type and power
Head style and wattage
Options
B= black
W= factory white
6N36= 6V-36W, NiCad
12N60= 12V-60W, NiCad
Blank= no heads*
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
Blank= auto-diagnostics, non-audible (standard)
U2= 120/277VAC input
AD= auto-diagnostics
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
CW= cold-weather -40°C, only with 6V single face
D3= time delay (15 mins.)
*Remote load must be
connected.
*Not all options available with NEXUS® System.
Please consult your sales representative
*Universal mounting
EXAMPLE: RNC1B12N60LD7
65
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Model No.:
Made in Canada
Typical specifications
N-tuf Series
NEMA-4X & NSF Certified
Combination Unit
Features
• NEMA-4X certified for wall or ceiling
mount or end mount
• NSF certified for food processing
• High efficiency MR16 lamps up to 12V,
12W or white LED emergency lights
• Continuous self-diagnostic monitoring
and monthly self-testing
• Fully automatic charger is solid state
• Non-intrusive magnetic test switch
• Cold weather (-40°C) option
• Comes standard with tamper-proof
screws
• NEXUS® compatible
• Sealed maintenance-free Nickel
Cadmium battery
• Meets or exceeds CSA 22.2 No. 141
Supply and install Ready-Lite® N-TUF combination of unit equipment and Exit Sign series. The equipment
shall operate under two input voltage, 120VAC or 347VAC. The equipment frame shall be of industrial grade
polyvinyl chloride with a gasket around lenses and canopy designed specifically for hostile environments.
The unit shall be certified for NEMA-4X for wall and ceiling and end mount designed specially for high abuse
areas, wet locations, and cold weather (CW option). The faceplate(s) shall be constructed of heavy-duty
vandal-resistant polycarbonate and feature an even illuminated legend. The legend light source shall be light
emitting diodes (LED). Red LED technology shall be ALINGAP. Emergency lights shall be fully adjustable and
high efficiency MR16 lamps. The Ready-Lite® Advanced Diagnostic Microcontroller board shall supply the
rated load for minimum of 1/2 hour to 87.5% of the rated battery voltage.
The unit shall be rated 120/347 V, 60 Hz and be CSA listed. The unit shall have an output of
V
W. The battery charger shall be driven by a micro-controller and shall include functions of Lockout, Brownout
Circuits, and Low Voltage Disconnection. It protects the unit from over-current, short-circuit, and reverse
polarity. The unit shall self-test for 5 minute every 30 days, 30 minutes on the 6th month and 90 minutes every
12 months. The unit shall be capable of full recharge in compliance with CSA specifications.
The unit shall be furnished with a magnetic test switch. A “Service Required” lamp shall be located near
the test switch and flash when a fault is detected. A four-LED diagnostic display shall be located inside the
equipment and shall identify the source of failure: battery, charger circuitry, LED lamps or emergency lights.
The Exit Sign shall be listed CSA-C22.2 No. 141 and CSA-C860 approved.
.
The equipment shall be Ready-Lite® Model:
n e m a - 4 x a n d n s f c e r t i f i ed fa m i ly
RNC Combo P. 64-65
RN P. 62
TUF P. 63
TUF-NM Battery P. 128-129
TUF-NM Remote P. 160-161
Wire guards WITH HEADS
460.0078-RL
wall mount
460.0060-RL
end or ceiling mount
Wire guards WITHOUT HEADS
460.0079-RL
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
POwer consumption
Model
AC Specs
Exit Sign Model
NM36
NM36-CW
120/347VAC
N12M60
66
Wattage capacity
1h30
2h00
30min
1h00
less than 2W
-
-
-
-
4h00
-
0.15/0.05 A
36
30
20
15
8
0.25/0.08 A
36
30
20
15
8
0.27/0.09 A
60
40
30
24
12
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Model No.:
Made in Canada
Dimensions
Dimensions are approximate and subject to change.
N-tuf Series
14” [35.7 cm]
3-7/8” [9.9 cm]
3-1/2” [8.7 cm]
NEMA-4X & NSF Certified
Combination Unit
9-1/4” [23.4 cm]
12-5/8” [32.1 cm]
13-1/4” [33.6 cm]
ordering information
Series
# ofHeads
NM36= 6
V-36W,
Blank= no heads*
NEMA 4X & 2= two heads
NSF
N12M60= 1
2V-60W,
NEMA 4X
& NSF
head style and wattage
faces
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
TUF1= s ingle
face
TUF2= double
face
housing/face colour
WH= white/white
WB= white/black
WA= w
hite/aluminum
BK= black/black
BA= black/aluminum
GY= grey/grey
GW= grey/white
GB= grey/black
voltage
options
Blank= 120/347VAC Blank= auto-diagnostics, non-audible
U277= 120/277VAC
(standard)
AD= auto-diagnostics, audible
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
CW= cold-weather -40°C**
G= green legend
*Not all options available with NEXUS®
System. Please consult your sales
representative
*Remote load must
be connected.
**Available with single face only.
EXAMPLE: NM362MITUF1WH
67
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
Features
• Includes the addition of Class II Div. 1&2
Groups E, F and G as well as Class III
ratings
• Compliant Class I Division 2, Groups
A, B, C and D as per CSA C22.2
No.137-M1981
• Temperature Code T6 (maximum +
85°C) as per Canadian Electrical Code,
Part I and CSA C22.2 No.137-M1981
• High-impact thermoplastic frame with
built-in gasket to secure against liquid
leaks
• Sealed, polycarbonate heavy-duty,
vandal-resistant face plate(s)
• C
oncealed pilot light and test switch
with magnetic action
• Long-life white LED light source
• Supplied standard with two pictogram
films per face, for direction selection
• Meets or exceeds CSA 22.2 No.141-10
standard for pictogram Exit Signs
• Universal AC input: two-wire 120 to
347VAC; standard DC input: two-wire
6 to 24VDC
• Energy efficient – consumes less than 2.5W
in AC or DC-remote mode
• Self-powered models come standard
with auto-diagnostic functions and
deliver two hours of back-up legend
illumination
• Suitable for cold-weather: -40°C for
AC/DC and -20°C for Self-powered
models (option: -CW)
h a z a r d o us l o c at i o n fa m i ly c l a ss I , II a n d III
TUFHZ P. 69
RHC Combo P. 70-71
HZ Combo P. 72-73
LDX-HZ Battery P. 130-131
NMHZ Remote P. 164
Dimensions
Dimensions are approximate and subject to change.
4-3/8” [11 cm]
4-3/8” [11.1 cm]
Pictogram Sign, Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
9-1/4” [23.4 cm]
RH Series
Supply and install the Ready-Lite® RH Series of pictogram Exit Signs. The equipment shall be certified for Hazardous
Locations: Class I Division 2 Groups A, B, C and D, Class II Divison 1&2 Groups E, F and G as well as Class III, with the
temperature code T6 (maximum 85ºC). The equipment frame shall be of industrial grade polyvinyl chloride
with a gasket around lenses and canopy. The faceplate(s) shall be constructed of heavy-duty vandal-resistant
polycarbonate and feature an even illuminated pictogram legend. Each face plate shall come standard with
two legend films for pictogram and direction selection. The light source shall be long-life white light-emitting
diodes (LED). The pictogram Exit Sign shall operate with universal 2-wire AC input voltage of 120 to 347VAC at
less than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC at less than 1W for single and double
face signs. The Self-powered model shall include a concealed pilot light and magnet-sensitive test switch, shall
use a sealed Nickel-Cadmium battery of 2.4V nominal voltage and shall stay illuminated during emergency
operation for at least two hours upon AC failure. The Self-powered model shall include auto-test functions: it
shall execute automatic tests for 5 minutes every 30 days, 30 minutes every 60 days and two hours annually.
When a fault is detected, the bi-colour pilot light shall turn from green to red and flash following a particular
code. The code description shall be visible on a label next to the pilot light to identify the failure type: battery,
charger circuitry, or LED lamps.
The pictogram Exit Sign shall meet or exceed the CSA 22.2 No.141-10 standard.
The equipment shall be Ready-Lite® Model:
.
13-1/4” [33.6 cm]
2-1/4” [5.7 cm]
< pictogram
left from here
pictogram
straight from
here
pictogram >
right from here
3-1/2” [8.9 cm]
Power Consumption
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
less than 2.5W
-
-
AC/DC standard
120 to 347VAC
less than 2.5W
6 to 24VDC
less than 1 W
AC/Special DC
120 to 347VAC
less than 2.5W
36, 48, 120VDC
less than 2.5 W
two-wire 120V AC/DC
120VAC
less than 2.5W
120VDC
less than 2.5 W
self-diagnostic
120/347VAC
less than 3.5W
nickel-cadmium battery
min. two hours
Ordering Information
Series
RH= pictogram
exit sign
Faces*
1= single face
2= double face
*Ceiling or wall
mount only.
Housing Colour
G= grey
Voltage
SPD= self-powered, auto-diagnostic, non-audible, NiCad, 120/347VAC
SPD2= self-powered, auto-diagnostic, non-audible, NiCad, 120/277VAC
U= universal 120 to 347VAC; 6 to 24VDC
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
2120= 2-wires 120VAC/VDC
NEX= NEXUS® system interface, 120/347VAC*
NEX2= NEXUS® system interface, 120/277VAC*
NEXRF= wireless NEXUS® system interface, 120/347VAC*
NEXRF2= wireless NEXUS® system interface, 120/277VAC*
*Not all options available with NEXUS® System. Please consult your sales representative
EXAMPLE: RH1GU
68
Options
CW= cold-weather (-20°C
for self-powered and
NEXUS® only)
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
Supply and install Ready-Lite® TUFHZ Series LED Exit Signs. The equipment shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than 3W and universal two-wire DC input voltage
from 6VDC to 48VDC at less than 2W for single and double face signs. Designed specifically for hostile
environments, the equipment frame shall be of industrial grade high impact thermoplastic with a gasket
around lenses and canopy. The faceplate(s) shall be constructed of heavy-duty vandal-resistant polycarbonate and feature an even illuminated legend. The light source shall be light emitting diodes (LED). Red LED
technology shall be ALINGAP. An LED-sensitive diffuser shall be mounted behind the legend to provide the 6”
high by 3/4” stroke letters with even illumination. The equipment shall be certified for Hazardous Locations:
Class I Division 2 Groups A, B, C and D, Class II Divison 1&2 Groups E, F and G as well as Class III, with the
temperature code T6 (maximum 85ºC). The equipment shall be designed specifically for high abuse areas,
wet location, and cold weather -20°C applications. The Self-powered model shall stay illuminated during
emergency operation for at least 90 minutes upon AC failure and shall include a magnetic test switch and
self-testing/self-diagnostic functions. The equipment shall automatically self test for 5 minutes every 30 days,
30 minutes every 60 days and 90 minutes annually. A “Service required” lamp shall be located near the test
switch and flash when a fault is detected. A two-LED diagnostic display shall be located inside the equipment
and shall identify the eventual source of failure (battery, charger circuitry, or LED lamps).
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Ready-Lite® Model:
h a z a r d o us l o c at i o n fa m i ly c l a ss I , II a n d III
RH P. 68
RHC Combo P. 70-71
HZ Combo P. 72-73
LDX-HZ Battery P. 130-131
NMHZ Remote P. 164
Wire guards
460.0080-RL
wall mount
460.0060-RL
ceiling mount
POwer consumption and unit rating
Model
AC Specs
DC Specs
AC/DC red
120 to 347VAC
less than 3W
6 to 48VDC
less than 2W
AC/DC green
120 to 347VAC
less than 3W
6 to 48VDC
less than 2W
self-powered red
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
self-powered green
120 to 347VAC
less than 3W
nickel-cadmium battery
min. 90 minutes
120VAC/VDC 2 wires, red
120VAC
less than 3W
120VDC
less than 3W
Note: double face models have double the power consumption above.
Dimensions
Dimensions are approximate and subject to change.
4-3/8” [11 cm]
13-1/4” [33.6 cm]
13-1/2” [34.2 cm]
9-1/8” [23.2 cm]
2-1/4” [5.7 cm]
tufHZ Series
LED Exit Sign, Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
Features
n • Includes the addition of Class II Div 1&2
Groups E, F and G as well as Class III
ratings
• Certified Class I Zone 2, Groups IIA,
IIB and IIC
• Certified Class I Div 2, Groups A, B,C and
D as per CSA C22.2 No.137-M1981
• Temperature Code: T6 (maximum 85ºC as
per Canadian Electrical Code, Part I
and CSA C22.2 No.137-M1981)
• C
SA certified, meets or exceeds CSA 22.2
No. 141 requirements
• Input voltages: 120 to 347Vac universal
AC input; 6 to 48Vdc universal DC input
• High impact thermoplastic frame, with
built-in gasket to prevent water infiltration
• Suited for areas with the risk of presence
of flammable gases, vapors or liquids
able to create an explosive atmosphere
• Sealed, polycarbonate faceplate
of heavy-duty, vandal-resistant
• Tamper-resistant, hermetically sealed
magnetic test switch
• Auto-diagnostic circuitry is standard on
Self-powered models
• Batteries recharge as per CSA
requirements and provide 90 minutes
of emergency operation
• Long-life, energy-efficient ALINGAP red
LED light source
• Energy efficient – consumes less than
3W in AC or DC mode
• Comes standard with industrial-grade,
Die-Cast aluminum electrical box
• Suitable for cold weather: -20°C
(Self-powered model, “CW” option)
and -40°C (AC only and AC-DC
models)
3-1/2” [8.8 cm]
ordering information
Series
TUFHZ= e xit sign
Faces/mounting
AC voltage
-1= single face, ceiling
or wall mount
-2= double face,
ceiling mount only
Blank= 1
20VAC
(L120-2W
only)
-U= universal,
120-347VAC
housing/faceplate Colour
GG= grey/grey
voltage
options
-DC= u
niversal 120-347VAC, 6-48VDC
-SPD= self-powered, auto-diagnostic,
non-audible NiCad, 120 to 347VAC
-L120-2W= 1
20VAC, 120VDC, 2 wires (AC only)
-NEX= NEXUS® system interface*
-NEXRF= w
ireless NEXUS® system interface*
Blank= red legend
G= green legend
CW= cold weather -20°C
self-powered only
*Not all options available with NEXUS® System.
Please consult your sales representative
EXAMPLE: TUFHZ-2-UGG-DC
69
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RHC Series
Pictogram Combo, Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
Features
•Includes the addition of Class II Div 1&2
Groups E, F and G as well as Class III
ratings
• Certified Class I Div 2, Groups A, B, C
and D as per CSA C22.2 No.137-M1981
• Certified temperature Codes for several
types of emergency lamps
• Certified CSA C22.2 No.141-10
• Polyvinyl chloride frame, with built-in
gasket to prevent water infiltration
• Heavy-duty 1/8” thick aluminum back
plate with keyholes for wall-mount
installation
• Sealed, polycarbonate vandal-resistant
faceplate
• Legend illuminated by long-life white
LEDs
• Comes standard with two pictogram
films for direction selection
• Two high-performance MR16 LED
lamps shielded by a clear polycarbonate
cover
• 5W LED emergency lights provide
60 ft of egress illumination on a 6-foot
wide path
• 6 W LED emergency lights provide
100 ft of egress illumination on a 6-foot
wide path
• Sealed, maintenance-free Lead-Calcium
or Nickel-Cadmium batteries
• Remote load capacity: covers with LED
lights 200 ft up to 500 ft of egress
illumination
• Comes standard with auto-diagnostic
• Cold-weather option: -40°C with only
14W extra power consumption
Supply and install Ready-Lite® RHC Series combination emergency light battery unit and pictogram sign.
Designed specifically for hazardous locations, the equipment frame shall be of industrial grade polyvinyl
chloride with gaskets around both sides of the frame contour. The back plate shall be made of 1/8” thick
aluminum sheet and shall include knock-outs for installation on an electrical box and four keyholes for alternative installation on a wall surface. The faceplate shall be constructed of heavy-duty vandal-resistant clear
polycarbonate and feature a uniformly illuminated pictogram legend.
The unit shall come standard with two legend films for pictogram and direction selection. The light source shall
be long-life white light-emitting diodes (LED). The unit shall have attached a lower compartment containing
two emergency heads with adjustable swivels and long-life MR-16 LED lamps of ___ V and ___ W. The heads
shall be installed on a shield housing made of cast aluminum and protected by a shock-absorbent, clear
polycarbonate cover. The standard AC input voltage shall be 120/347VAC. The equipment shall be equipped
with a magnetic test switch and one LED pilot light protected by the face plate.
The unit shall perform auto-test functions managed by a micro-controller and shall automatically self-test for
one minute every 30 days, 10 minutes in the 6th month and 30 minutes annually. When a fault is detected,
the bi-color pilot light shall turn from green to red and flash following a particular code. The code description
shall be displayed on a label next to the pilot light to identify the failure type: battery, charger circuitry, LED
lights for the signage, or emergency lights. The combination unit shall be approved CSA C22.2 No.141-10
and No.137-M1981 for Class I Division 2 Groups A, B, C and D, Class II Divison 1&2 Groups E, F and G as
well as Class III.
.
The combination unit shall be Ready-Lite® model:
h a z a r d o us l o c at i o n fa m i ly c l a ss I , II a n d III
RH P. 68
TUFHZ P. 69
HZ Combo P. 72-73
LDX-HZ Battery P. 130-131
NMHZ Remote P. 164
Temperature codes (class I division 2)
lamp rating
temperature code
max. temperature
replacement lamp
6V-10W
T3C
160°C
580.0079-RL
12V-12W
T3A
180°C
580.0080-RL
12V-20WH
T2D
215°C
580.0068-RL
6V-4W LED
T4A
120°C
580.0097-RL
12V-4W LED
T4A
120°C
580.0093-RL
12V-5W LED
T4A
120°C
580.0104-RL
12V-6W LED
T4
135°C
580.0106-RL
Power Consumption
MODEL
AC SPECS
Emergency power available for lamps
30min
1h00
1h30
2h00
4h00
Pictogram Sign Module
less than 2.5W
-
-
-
-
-
RHC-6L36
0.10/0.03 A
36
21
15
12
-
RHC-6L36-CW
0.25/0.08 A
36
21
15
12
-
0.10/0.03 A
36
30
20
16
8
RHC-6N36
120/347VAC
RHC-6N36-CW
0.25/0.08 A
36
30
20
16
8
RHC-12N60
0.18/0.06 A
60
40
30
20
10
70
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
RHC Series
14-1/2” [36.8 cm]
3-1/2” [8.7 cm]
13-3/4” [34.9 cm]
Pictogram Combo, Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
picto
Straight from here
6-1/4” [15.9 cm]
12-5/8” [32.1 cm]
<picto
Left from here
picto>
Right from here
Ordering Information
series
RHC= pictogram combo
housing colour
battery type and power
G= grey
6L36= 6
V-36W, lead-calcium
6N36= 6V-36W, NiCad
12N60= 1
2V-60W, NiCad
Head style and wattage
Blank= no heads*
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
MK= MR16 halogen, 12V-12W
MW= MR16-IR, 12V-20W, high output
*Remote load must be connected.
EXAMPLE: RHCG12N60Ld7
71
Options
Blank= auto-diagnostics, non-audible (standard)
U2= 120/277VAC input
AD= auto-diagnostics, audible
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
CW= cold-weather -40°C (only 6V units)
D1= time delay (5 mins.)
D2= time delay (10 mins.)
D3= time delay (15 mins.)
*Not all options available with NEXUS® System. Please
consult your sales representative
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
HZ Series
LED Exit Combo, Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
n
Features
•Includes the addition of Class II Div 1&2
Groups E, F and G as well as Class III
ratings
• Certified Class I Zone 2, Groups IIA, IIB
and IIC
• Certified Class I Division 2, Groups A, B,
C and D as per CSA C22.2
No.137-M1981
• Certified temperature Codes for several
types of emergency lamps
• Certified CSA C22.2 No141
• Certified CSA C860
• Polymeric frame, with built-in gasket
to prevent water infiltration
• Heavy-duty 1/8” thick aluminum back
plate with keyholes for secure
wall-mount installation
• Sealed polycarbonate faceplate
of heavy-duty, vandal-resistant
• Suited for areas with the risk of
flammable gases, vapors or liquids that
can create an explosive atmosphere
• Exit Sign module illuminated by longlife, energy-efficient ALINGAP red LEDs
• Two MR16 halogen lamps, shielded by
a cast aluminum housing and a
polycarbonate cover
• 5W LED emergency lights provide
60 ft of egress illumination on a 6-foot
wide path
n • 6W LED emergency lights provide
100 ft of egress illumination
on a 6-foot wide path
• Sealed, maintenance-free, Lead-Calcium
or Nickel-Cadmium batteries
n • Remote load capacity: covers with LED
lights 200 ft up to 800 ft of egress
illumination
• Comes standard with auto-diagnostic
functions
• ½” electrical conduit entry on both
sides and at the top
• NEXUS® compatible (for more
information on NEXUS®, contact your
sales representative)
Supply and install Ready-Lite® HZ Series combination emergency light battery unit and LED Exit Sign.
Designed specifically for hostile environments, the equipment frame shall be of industrial grade polymer
with gaskets around both sides of the frame contour. The back plate shall be made of 1/8” thick aluminum
sheet and shall include knockouts for installation on an electrical box and four keyholes for alternative installation on a wall surface. The faceplate shall be constructed of heavy-duty vandal-resistant
polycarbonate and feature a uniformly illuminated legend.
The light source shall be light emitting diodes (LED). Red LED technology shall be ALINGAP. An LED-sensitive diffuser shall be mounted behind the legend to provide the 6” high by 3/4” stroke letters with even
illumination. When specified, the equipment shall have attached a lower compartment containing
two emergency lights with adjustable swivels and long-life MR-16 halogen lamps of
V and
W. The lamps shall be shielded by cast aluminum housing and protected by a shock-absorbent,
transparent polycarbonate cover.
The equipment shall be certified for Hazardous Locations: Class I Division 2 Groups A, B, C and D, Class II
Divison 1&2 Groups E, F and G as well as Class III. The standard AC input voltage shall be 120/347VAC. The
equipment shall be equipped with a magnetic test switch located behind the face plate and two LED pilot
lights: AC-on and “Service required”.
The unit shall include self-testing/self-diagnostic functions monitored by a micro-controller and shall
automatically self test for one minute every 30 days, 10 minutes in the 6th month and 30 minutes annually.
The “Service required” LED shall light when a fault is detected. A four-LED diagnostic display located inside
the equipment shall identify the source of the failure (battery, charger circuitry, or lamp load).
The Exit Sign module shall be CSA-C860 approved.
The combination unit shall be Ready-Lite® Model:
.
h a z a r d o us l o c at i o n fa m i ly c l a ss I , II a n d III
RH P. 68
TUFHZ P. 69
RHC Combo P. 70-71
LDX-HZ Battery P. 130-131
NMHZ Remote P. 164
Wire guards
460.0078-RL
wall mount
Temperature codes (Class I Division 2)
lamp rating
temperature code
max. temperature
replacement lamp
6V-10W
T3C
160°C
580.0079-RL
12V-12W
T3A
180°C
580.0080-RL
12V-20WH
T2D
215°C
580.0068-RL
6V-4W LED
T4A
120°C
580.0097-RL
12V-4W LED
T4A
120°C
580.0093-RL
12V-5W LED
T4A
120°C
580.0104-RL
12V-6W LED
T4
135°C
580.0106-RL
POwer consumptioN
Model
AC Specs
HZ36N
H12Z60
120/347VAC
H12H10
72
Wattage capacity
30min
1h00
1h30
2h00
0.15/0.06 A
36
30
20
15
4h00
-
0.30/0.10 A
60
40
30
20
10
0.30/0.10 A
100
72
40
36
18
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
14-1/2” [36.8 cm]
HZ Series
3-1/2” [8.7 cm]
LED Exit Combo, Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
6-1/4” [15.9 cm]
12-5/8” [31.1 cm]
13-3/4” [34.9 cm]
ordering information
Series
Number of
heads
head style/ wattage
HZ36N= 6
V-36W, NiCad
Blank= no heads* LD1= MR16 LED, 6V-4W
H12Z60= 1
2V-60W, NiCad 2= two heads
LD7= MR16 LED, 12V-4W
H12H10= 1
2V-100W, NiMH
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
MJ= MR16 halogen,
6V-10W
MK= MR16 halogen,
12V-12W
MW= MR16-IR, 12V-20W,
high output
Housing
face colour
GG= grey/grey
Voltage
Blank= 120/347VAC
U2= 120/277VAC
LEGEND colour
Blank= red legend
G= green legend
options
AD= auto-diagnostics, audible
ADN= auto-diagnostics, non-audible
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
*Not all options available with NEXUS®
System. Please consult your sales
representative
*Remote load must
be connected.
EXAMPLE: HZ36N2MJGGAD
73
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RX Series
Remote Pictogram Exit Sign for
Hazardous Locations
TP Series Transfer Panels
Features
Remote Picto Sign Series
• CSA Certified for use in hazardous
locations:
- Class I, Division 1, Groups, A, B, C, D
- Class I, Division 2, Groups A, B, C, D
- Class III, Divisions 1 and 2
• Very low Temperature Codes (see table)
• Listed CSA C22.2 No.137-M1981
• Listed CSA 22.2 No.141-10
• Lighting fixture of die-cast aluminum
with grey epoxy powder coat finish
• Legend housing of industrial-grade
14-gauge steel with grey enamel finish
• Supplied standard with two pictogram
films per face, for direction selection
• Long-life white LED light source
• Two-wire AC/DC input available in 6, 12,
24 or 120V
• Energy efficient – consumes maximum
4.0W in AC and DC mode
• Also available as self-powered
TP Series Transfer Panel
• Available with housing for hazardous
locations (Class 1, Division 1) or
NEMA-1 housing (for use outside the
hazardous location area)
• Standard AC input: 120Vac, optional:
277Vac, 347Vac
• Standard DC input: 6, 12 or 24Vdc
• Two-wire output with permanently
present AC/DC low voltage
• Output power: 25W, can drive up to six
(6) RX Series remote pictogram exit
signs
Supply and install the Ready-Lite® RX Series remote pictogram exit signs. The lighting fixture shall have a
die-cast aluminum body with grey epoxy powder coat finish and a transparent glass globe. The light source
shall be long-life Light-Emitting Diodes (LED) in a lamp assembly rated __V. The LED assembly shall emit white
light and shall consume less than 4W in AC or DC current. The legend housing shall be of industrial-grade
14-gauge steel with grey enamel finish. The face plate(s) shall consist of three layers: a white translucent
panel, a green/clear legend film and a clear Polycarbonate panel for rigidity enforcement. Each face plate
shall come standard with two legend films per face, for direction selection.
The equipment shall be certified CSA C22.2 No.137-M1981 for Hazardous Locations: Class __, Division ___,
Groups ______ with the temperature code: _______.
The equipment shall be certified CSA 22.2 No.141-10
The equipment shall be Ready-Lite® Model: ____________________________________________________ .
TP Series Transfer panel:
Supply and install the Ready-Lite® TP Series transfer panel for hazardous location remote Exit Signs. The unit
shall have two voltage inputs:
VAC and
VDC and shall be able to maintain an output of
V 25W for the permanent supply of a total of five remote LED Exit Signs.
, Division
, Group
or for a
The transfer panel shall be suitable for Class
NEMA 1 environment.
The unit shall be Ready-Lite® Model:
.
Power consumption and unit rating
Model
AC Specs
DC Specs
6VAC
6VDC
12VAC
AC/DC
maximum 4W
24VAC
120VAC
12VDC
maximum 4W
24VDC
120VDC
*NOTE: Exit Signs of 6,12 or 24 V must be connected through transfer panels; maximum six Pictogram Exit Signs per panel.
1. severity code Selection Guide
Environment
Severity Code
Class I Div.1 Groups A, B
S1
Class I Div.1 Groups C, D
S2
Class I Div.2 Groups A, B, C, D
S3
Class II Div. 1 & 2 Groups E, F, G
Class III Div.1 and 2
S4
2. Temperature codes: measured at 40°C Ambient
Severity Code
S1
S2
S3
S4
Temperature Code
T6
T6
T4A
T6 (E, F, G)
CSA/UL rating
maximum 85o C
maximum 85o C
maximum 85o C
maximum 85o C
74
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
S1 & S2
12-3/8” [31.4 cm]
12-3/8” [31.1 cm]
18-1/2” [47.0 cm]
9-5/8” [24.5 cm]
17-3/8” [44.2 cm]
7-1/8” [18.1 cm]
14-1/8” [37.7 cm]
24-1/4” [61.5 cm]
5-1/4” [13.3 cm]
RX Series
33” [83.9cm]
Severity S1 & S2
14-3/5” [15.5cm]
1. RX Series
6” [15.5cm] 5” [11.5cm]
Dimensions are approximate and subject to change.
Remote Pictogram Exit Sign for
Hazardous Locations
TP Series Transfer Panels
12-3/8” [31.4 cm]
12-3/4” [31.4 cm]
12-3/8” [31.4 cm]
30-3/4” [78.0 cm]
28-1/2” [72.3 cm]
12-1/4 [31.2 cm]
2-1/2” [5.7 cm]
3-3/8” [8.4 cm]
3-1/2” [9 cm]
4” [10.1 cm]
11-1/2” [28.7 cm]
19-3/4” [50 cm]
10-1/4” [27 cm]
3-3/8” [8.4 cm]
Severity S4
10-7/8” [27.5 cm]
8” [15.3 cm] 8” [15.3 cm]
16-1/4” [41.2 cm]
30-3/8” [77.1 cm]
12-3/8” [31.4 cm]
13-3/8” [34.1 cm]
No Severity Rating
2. Transfer Panels
Severity S1, S2, s3 & S4
8-1/2” [21.5 cm]
4-1/8” [10.4 cm]
9” [22.9 cm]
10” [25.4 cm]
8-3/8” [21.3 cm]
9-1/4” [23.5 cm]
8” [20.3 cm]
10-1/2” [25 cm]
< Picto
left from
here
Picto
straight
from here
Picto >
right from
here
Ordering Information
Before ordering, identify the environment of your application: Class
, Division
, Group
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
.
1. RX Series
Series
RX= hazardous location
pictogram sign
No. of Faces
1= single face
2= double face
Severity Code
Mounting
S1= Class I Div.1 Gr. A, B
S2= Class I Div.1 Gr. C, D
S3= Class I Div.2 Gr. A, B, C, D
S4= Class
II Div.1&2 Gr. E, F, G Class
III Div.1&2
C= ceiling
P= pendant
W= wall*
Input Voltage
6= 6V AC/DC
12= 12V AC/DC
24= 24V AC/DC
120= 120V AC/DC
* Wall-mount only available for
severities S2, S3 and S4
EXAMPLE: RX1S1C6
Unlike EXIT signs, the pictogram sign is not available in double arrow configuration.
2. Transfer Panel
AC Voltage
120= 120VAC
347= 347VAC
277= 277VAC
DC Voltage
-6= 6V
-12= 12V
-24= 24V
-120= 120V
Series
-TP= transfer panel
Load Power
-25= 25W*
*4W required per DC “Pictogram Exit” load
EXAMPLE: 120-6-TP-25
75
Housing
Blank= NEMA1
XP= hazardous locations
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RFX-EX Series
Hazardous Location Exit Sign
TP Series Transfer Panels
Features
Remote Exit Sign Series
• CSA Certified for use in
hazardous locations:
-C
lass I, Divisions 1, Groups
A, B, C, D
- Class II, Divisions 2, Groups
A, B, C, D
- Class III, Divisions 1 and 2
• Die-Cast aluminum body with grey
epoxy powder coat finish
• Exit housing and faceplate made of
industrial-grade
14-gauge steel and finished in grey
enamel
• Faceplate features universal knockout
chevrons
• Two-wire input circuit for both AC and
DC inputs
• Available in 6, 12, 24 and 120Vac/dc
• LED lamp with ALINGAP LEDs;
consumes less than 5W in AC and DC
mode
• New, easy-to-build catalogue number
based on the Ready-Lite® Severity Codes
• CSA certified, meets or exceeds
CSA 22.2 No. 141 requirements
• Also available as Self-powered Exit Sign,
battery unit and combo unit; see
LDX-EXP catalogue sheet
TP Series Transfer panel
Supply and install the Ready-Lite® RFX-EX Series remote Exit Sign. The exit housing shall be industrial grade
14-gauge steel and finished in grey enamel. The faceplate will be constructed of heavy-duty 14-gauge steel
and feature universal knockout chevrons and the red letters shall not be less than 6” in height with a 3/4”
stroke. The sign shall come complete with a
Volt LED lamp, and function from one voltage source
only, in AC and DC current. The LED Lamp shall use ALINGAP LEDs and shall consume less than 5W in either
AC or DC current.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The Exit Sign shall be suitable for Class
, Division
, Group
.
The Exit Sign shall be Ready-Lite® Model:
.
TP Series Transfer panel:
Supply and install the Ready-Lite® TP Series transfer panel for hazardous location remote Exit Signs. The unit
shall have two voltage inputs:
VAC and
VDC and shall be able to maintain an output of
V 25W for the permanent supply of a total of five remote LED Exit Signs.
The transfer panel shall be suitable for Class
, Division
, Group
or for a NEMA 1
environment.
The unit shall be Ready-Lite® Model:
.
Power consumption and unit rating
Model
AC Specs
DC Specs
6VAC
6VDC
12VAC
AC/DC red
two-wire
less than 5W
24VAC
120VAC
12VDC
less than 5W
24VDC
120VDC
*NOTE: Exit Signs of 6,12 or 24 V must be connected through transfer panels; maximum five Exit Signs per panel.
1. severity code Selection Guide
Environment
Severity Code
Class I Div.1 Groups A, B
S1
Class I Div.1 Groups C, D
S2
Class I Div.2 Groups A, B, C, D
S3
Class II Div. 1 & 2 Groups E, F, G
Class III Div.1 and 2
S4
2. Temperature codes: measured at 40°C Ambient
Severity Code
S1
S2
S3
S4
Temperature Code
T6
T6
T4A
T6 (E, F, G)
CSA/UL rating
maximum 85o C
maximum 85o C
maximum 85o C
maximum 85o C
• Available with explosion-proof housing
(Class 1, Division 1) or NEMA-1
housing (for use outside the hazardous
location area)
• Standard AC input: 120Vac, optional
277Vac, 347Vac; standard DC input:
6, 12 or 24Vdc
• Two-wire output with permanently
present AC/DC low voltage
• Output power: 25W, can drive up to
five (5) RFX-EX series remote exit signs
76
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
dimensions
Dimensions are approximate and subject to change.
pendant mount
12-3/8” [31.4 cm]
8-1/2” [21.5 cm]
9-5/8” [24.5 cm]
17-3/8” [44.2 cm]
5-1/4” [13.3 cm]
RFX-EX Series
Hazardous Location Exit Sign
TP Series Transfer Panels
8-3/8” [21.3 cm]
4-1/8” [10.4 cm]
12-3/8” [31.4 cm]
30-3/8” [77.1 cm]
transfer panel
hazardous
location
severity S1, S2, S3, S4
14-7/8” [37.7 cm]
33” [83.9 cm]
ceiling mount
7-1/8” [18.1 cm]
14-7/8” [37.7 cm]
24-1/4” [61.5 cm]
DOUBLE pendant mount
6” [15 cm] 6” [15 cm]
SEVERITY S1, S2, S3
9-1/4” [23.5 cm]
10” [25.4 cm]
9” [22.9 cm]
12-3/8” [31.4 cm]
13-3/8” [34.1 cm]
12-3/8” [31.4 cm]
nema-1
transfer panel
10-1/4” [26 cm]
8” [20.3 cm]
2-1/4” [5.7 cm]
10-7/8” [27.5 cm]
28-1/2” [72.3 cm]
4” [10.1 cm]
wall mount
3-3/8” [8.4 cm]
12-1/4” [31.2 cm]
12-3/8” [31.4 cm]
30-3/4” [78 cm]
ceiling mount
3-1/2” [9 cm]
11-1/4” [28.7 cm]
3-1/8” [7.8 cm]
10-7/8” [27.5 cm]
19-3/4” [50 cm]
DOUBLE pendant mount
6” [15 cm] 6” [15 cm]
pendant mount
SEVERITY S3, S4
Ordering Information
Before ordering, identify the environment of your application: Class
, Division
, Group
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
.
3. RFX-Ex
Series
RFX-EXSF= exit single face C860 LED
RFX-EXDF= exit double face C860 LED
severity code
voltage
S1= CL.I, Div.1, Gr. A, B
S2= CL.I, Div.1, Gr. C, D
S3= CL.I, Div.2, Gr. A, B, C, D
S4= C
L.II, Div.1, & 2 Gr.E, F, G, CL.III, Div.1 & 2
-6= 6V
-12= 12V
-24= 24V
-120= 120V
mounting
C= ceiling
P= pendant
W= wall*
*Severity 2, 3 and 4 only
EXAMPLE: RFX-EXSFS1-6C
4. Transfer Panel
AC Voltage
120= 120VAC
347= 347VAC
277= 277VAC
DC voltage
-6= 6V
-12= 12V
-24= 24V
-120= 120V
Series
-TP= transfer panel
load wattage
-25= 25W*
*5W required per DC Exit load
EXAMPLE: 120-6-TP-25
77
housing
Blank= NEMA 1
XP= hazardous locations
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RFX-CS Series
“Sortie” Sign and
Transfer Panels for
Hazardous Locations
Features
Remote Sortie Sign Series
• CSA certified for use in
hazardous locations:
- Class I, Divisions 1, Groups
A, B, C, D
- Class II, Divisions 2, Groups
A, B, C, D
- Class III, Divisions 1 and 2
• Die-Cast aluminum body with grey
epoxy powder coat finish
• Sortie Sign housing and faceplate
made of 14-gauge steel, grey enamel
finish
• Faceplate features universal directional
chevrons (knockouts)
• Two-wire circuit for both AC and DC
inputs
• Available in 6, 12, 24 and 120Vac/dc
• Light source is ALINGAP LEDs;
consumes less than 5W in AC or DC
mode
• New, easy-to-build catalog number
based on the Ready-Lite® severity
codes
• C
SA certified, meets or exceeds
CSA 22.2 No. 141
• Also available as Self-powered Exit
Sign, battery unit and combo unit;
see LDX-EXP-S catalogue sheet
TP Series Transfer panel
Supply and install the Ready-Lite® RFX-CS Series remote “SORTIE” sign. The exit housing shall be industrial
grade 14-gauge steel and finished in grey enamel. The faceplate will be constructed of heavy-duty
14-gauge steel and feature universal knockout chevrons and the red letters shall not be less than 6” in height
with a 3/4” stroke. The sign shall come complete with a
Volt LED lamp, and function from one voltage
source only, in AC and DC current. The LED Lamp shall use ALINGAP LEDs and shall consume less than 5W in
either AC or DC current.
The Sortie Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The Sortie Sign shall be suitable for Class
, Division
, Group
.
The Sortie Sign shall be Ready-Lite Model:
.
®
TP Series Transfer panel:
Supply and install the Ready-Lite® TP Series transfer panel for hazardous location remote Exit Signs. The
unit shall have two voltage inputs:
VAC and
VDC and shall be able to maintain
an output of
V 25W for the permanent supply of a total of five remote LED Exit Signs.
The transfer switch shall be suitable for Class
, Division, Group
The unit shall be Ready-Lite® Model:
, or for a NEMA 1 environment.
.
Power consumption and unit rating
Model
AC Specs
DC Specs
6VAC
6VDC
12VAC
AC/DC red
two-wire
less than 5W
24VAC
120VAC
12VDC
less than 5W
24VDC
120VDC
*NOTE: SORTIE signs of 6,12 or 24 V must be connected through transfer panel; maximum five sortie signs per panel.
1. severity code Selection Guide
Environment
Severity Code
Class I Div.1 Groups A, B
S1
Class I Div.1 Groups C, D
S2
Class I Div.2 Groups A, B, C, D
S3
Class II Div. 1 & 2 Groups E, F, G
Class III Div.1 and 2
S4
2. Temperature codes: measured at 40°C Ambient
Severity Code
S1
S2
S3
S4
Temperature Code
T6
T6
T4A
T6 (E, F, G)
CSA/UL rating
maximum 85o C
maximum 85o C
maximum 85o C
maximum 85o C
• Available with housing for hazardous
locations (Class 1, Division 1) or
NEMA-1 housing (for use outside the
hazardous location area)
• Standard AC input: 120Vac, optional:
277Vac, 347Vac
• Standard DC input: 6, 12 or 24Vdc
• Two-wire output with permanently
present AC/DC low voltage
• Output power: 25W, can drive up to
five (5) remote units Series RFX-CS
78
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
dimensions
Dimensions are approximate and subject to change.
wall mount
(only severity S2)
18” [45.7 cm]
18” [45.7 cm]
8-1/2” [21.5 cm]
14-7/8” [37.7 cm]
33” [83.9 cm]
6” [15.3 cm] 6” [15.3 cm]
rfx-cs Series
8-3/8” [21.3 cm]
4-1/8” [10.4 cm]
18” [45.7 cm]
42” [106.8 cm]
9-5/8” [24.5 cm]
17-3/8” [44.2 cm]
7-1/8” [18.1 cm]
14-7/8” [37.7 cm]
24-1/4” [61.5 cm]
5-1/4” [13.3 cm]
10-5/8” [26.9 cm]
18-3/8” [46.6 cm]
ceiling mount
DOUBLE pendant mount
pendant mount
12-3/8” [31.4 cm]
16-1/8” [41.1 cm]
SEVERITY S1, S2
“Sortie” Sign and
Transfer Panels for
Hazardous Locations
18” [45.7 cm]
3-1/2” [9 cm]
11-1/4” [28.7 cm]
18” [45.7 cm]
42” [106.8 cm]
4” [10.2 cm]
4-1/8” [10.4 cm]
8” [20.3 cm]
9-1/4” [23.5 cm]
10-1/4” [26 cm]
3” [7.7 cm]
10-3/4” [27.4 cm]
19-5/8” [49.9 cm]
ceiling mount
nema-1
10-7/8” [27.5 cm]
28-1/2” [72.3 cm]
DOUBLE pendant mount
pendant mount
6” [15.3 cm]
wall mount
4-1/2” [11.5 cm]
12-1/4” [31.2 cm]
SEVERITY S3, S4
7/8” [2.1 cm]
12-3/8” [31.4 cm]
transfer switch
hazardous
location
severity S1, S2, S3, S4
9” [22.9 cm]
10” [25.4 cm]
Ordering Information
Before ordering, identify the environment of your application: Class
, Division
, Group
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
.
3. RFX-CS
Series
RFX-CSSF= sortie single face
RFX-CSDF= sortie double face
severity code
mounting
S1= CL.I, Div.1&2, Gr. A, B
S2= CL.I, Div.1&2, Gr. C, D
S3= CL.I, Div.2, Gr. A, B, C, D
S4= CL.II, Div.1, & 2 Gr.E, F, G CL.III, Div.1 & 2
C= ceiling
P= pendant
W= wall*
voltage
6= 6V
12= 12V
24= 24V
120= 120V
*Note: wall mount available only for
severities S2, S3 and S4
EXAMPLE: RFX-CSSFS1C6
4. Transfer panel
AC Voltage
120= 120VAC
347= 347VAC
277= 277VAC
DC voltage
-6= 6V
-12= 12V
-24= 24V
-120= 24V
Series
-TP= transfer panel
load wattage
-25= 25W*
*5W required per DC “Sortie” load
EXAMPLE: 120-6-TP-25XP
79
housing
Blank= NEMA 1
XP= hazardous locations
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
LDX-EXP-P Series
Battery Units,
Self-powered Pictogram
Exit Signs & Combination Units
CSA certified for use in
hazardous locations
The LDX-EXP-P Series of battery equipment is
designed to cover emergency lighting applications for the entire spectrum of hazardous
locations, where inflammable gases, vapors,
liquids, dust particles, fabrics or tissues are
permanently present or are likely to exist.
In one simple-to-order catalogue family the
LDX-EXP-P Series combines three traditional
emergency lighting products with battery
back-up: battery units with emergency
lights, Self-powered Pictogram Exit Signs,
and combination units with emergency lights
and Pictogram Exit Sign. The equipment is
also available with additional emergency
power capacity to drive remote heads and
Pictogram Exit Signs.
Features
• CSA Certified for use in hazardous
locations:
- Class I, Divisions 1 and 2, Groups
A, B, C, D
- C
lass II, Divisions 1 and 2, Groups
E, F, G
- Class III, Divisions 1 and 2
• D
ie-Cast aluminum body with grey
epoxy powder coat finish; clear, impact
and heat resistant prismatic glass globe
• Long-life, maintenance-free
Lead-Calcium battery
• Battery charger is current limited,
temperature compensated, short-circuit
proof and reverse polarity protected
• Emergency heads with one or twin
lamp design
• Self-powered combo includes a transfer
circuit to drive an additional five (5)
remote pictogram exit signs (total power
max 25W)
• The Self-powered version is CSA C22.2
No. 141-10 certified
Supply and install the Ready-Lite® LDX-EXP-P Series of hazardous location battery unit equipment. The battery
unit housing will be constructed of Die-Cast aluminum with grey epoxy powder coat finish. The equipment
shall be rated for 120, 277 or 347V, 60 Hz input and be CSA listed. The equipment shall have an output of
V and
W and shall supply the rated load for minimum of 1/2 hour to 87.5% of the
rated battery voltage. The battery shall be a long-life, maintenance-free Lead-Calcium type. The charger shall
be fully computer tested and have its charge voltage set in the factory to ± 1% tolerance. The charger shall be
current limited, temperature compensated, short circuit proof and reverse polarity protected. The charger shall
be furnished with an electronic lockout circuit, which will connect the battery when the AC circuit is activated,
and an electronic brownout circuit, which will activate the emergency heads when the utility power dips below
75% of nominal voltage. Where required the equipment shall come complete with
heads, each
of them equipped with
lamp(s) of
W. The head housing shall be Die-Cast aluminum
with grey epoxy powder coat finish. The lenses shall be a clear, impact and heat resistant prismatic glass globe.
The head shall be factory sealed, with no need for external seals. Where required the equipment shall come
complete with one Exit Sign and will include a transfer circuit to maintain the Exit Sign permanently lighting in
both normal and emergency operation. The exit housing shall be industrial grade 14-gauge steel and finished
in grey enamel. The face plate(s) shall consist of three layers: a white translucent panel, a green/clear legend
film and a clear Polycarbonate panel for rigidity enforcement. Each face plate shall come standard with two
legend films per face, for direction selection.
The equipment shall be certified CSA C22.2 No.137-M1981 for Hazardous Locations: Class __, Division ___,
Groups ______ with the temperature code: _______.
The equipment shall be certified CSA 22.2 No.141-10
The equipment shall be Ready-Lite® Model: ____________________________________________________ .
POwer consumption and unit rating
Model
AC Specs
LDX636EXP
LDX672EXP
LDX6108EXP
LDX1272EXP
LDX12144EXP
LDX12200EXP
LDX24144EXP
LDX24288EXP
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
120/347VAC
30min
1h00
36
72
108
72
144
200
144
288
21
42
63
42
84
117
84
168
Wattage capacity
1h30
2h00
15
30
45
30
60
83
60
120
4h00
12
24
36
24
48
67
48
96
6
12
18
12
24
33
24
48
NOTE: The wattage capacity applies only to the battery unit. For combo or Self-powered Pictogram Exit Signs one must allocate 4W of
emergency power for each sign.
Temperature codes: measured at 40°C Ambient
Explosion-proof equipment is composed of one or more modules, each of them qualified for a specific temperature code. The temperature code of the complete equipment (enclosure + exit sign + emergency heads)
is defined as the most severe of the temperature codes identified for each of the modules below.
1. temperature codes for LDX-EXP-P Series (battery unit enclosure)
Severity Code
S1, S1A
S2
S3, S3A
S4
Temperature Code
T6
T6
T6
T6
2. temperature codes for RX Series* (Pictogram exit sign)
Severity Code
S1
S2
S3
S4
Temperature Code
T6
T6
T4A
T6 (E, F, G)
*Self-Powered Pictogram Exit Sign only (no heads).
3. temperature codes for RFX Series (emergency heads)
Severity
Code
Quartz bi-pin
12W, 20W
MR16
12V-12W
MR16
12V, 24V-20W
MR16
12V, 24V-35W
MR16
12V, 24V-50W
MR16
120V-20W
MR16
120V-35W
MR16
120V-50W
S1
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
S2
T5 (100
T6 (85
T5 (100
T4A (120
T3C (160
T5 (100
T3A (180
T3 (200o C)
S3
T1 (450o C)
T4 (450o C)
T3 (200o C)
T2 (300o C)
T1 (450o C)
T2D (215o C)
T2 (300o C)
T1 (450o C)
S4
T4A (120 C)
(E,F,G)
T5 (100 C)
(E,F,G)
T5 (100 C)
(E,F,G)
T4A (120 C)
(E,F,G)
T3C (160 C)
(E,F,G)
T4A (120 C)
(E,F,G)
T3C (160 C)
(E,F,G)
N/A
o
C)
o
o
C)
o
80
o
o
C)
o
o
C)
o
o
C)
o
C)
o
o
o
C)
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
SMALL CABINET (36-72W)
18-1/4” [46.5 cm]
20-7/8” [53 cm]
22-7/8” [58.2 cm]
19-5/8” [50 cm]
22-7/8” [58.2 cm]
9-5/8” [24.4 cm]
19-5/8” [50 cm]
LDX-EXP-P Series
6-3/8” [16.3 cm]
10-3/8” [26.4 cm]
27-3/4” [70.5 cm]
Battery Units,
Self-powered Pictogram
Exit Signs & Combination Units
14-3/8” [36.6 cm]
LARGE CABINET (108-288W)
13-1/8” [33.3 cm]
21-1/4” [53.9 cm]
23-3/4” [60.4 cm]
23-3/8” [59.2 cm]
20-1/8” [51 cm]
23-3/8” [59.2 cm]
20-1/8” [51 cm]
10” [25.4 cm]
8-1/4” [20.8 cm]
14-3/8” [36.6 cm]
30-5/8” [77.8 cm]
< picto left
from here
picto straight
from here
picto right >
from here
Ordering Information
Identify the environment of your application: Class
, Division
Refer to table 4 for the Severity Code to use in your catalogue number.
, Group
.
4. severity code Selection chart
Environment
Severity Code
Cl. I, Div. 1, Gr. A*
S1A
Cl. I, Div. 1, Gr. B
S1
Cl. I, Div. 1, Gr. C, D
S2
CI. I, Div. 2, Gr. A*
S3A
CI. I, Div. 2, Gr. B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G
Cl. III, Div. 1 & 2
S4
*Units for Class I Group A are not available with test switch and pilot light.
Ordering chart
dc
voltage
LDX6= 6V
capacity
cabinet size
Series head style
-36= 36W (S)*
EXP
-72= 72W (S)*
-108= 108W (L)*
LDX12= 12V -72= 72W (S)*
-144= 144W (L)*
-200= 200W (L)*
LDX24= 24V -144= 144W (L)*
-288= 288W (L)*
*Cabinet size
not part of
nomenclature
Blank= n
o
heads
/11= single
remote,
1 lamp
/12= single
remote,
2 lamps
/21= double
remote,
1 lamp
each
Severity code
S1A= CL.I, Div.1, Gr. A*
S1= CL.I, Div.1, Gr. B
S2= CL.I, Div.1, Gr. C, D
S3A= CL.I, Div.2, Gr. A*
S3= CL.I, Div.2, Gr. B, C, D
S4= CL.II, Div.1, & 2
Gr. E, F, G
CL.III, Div.1 & 2
*Sold without test switch or
pilot light
Lamp Type
faces
Blank= no lamp
12= 6V, 12V - 12W,
quartz bi-pin
20= 6V to 24V-20W,
quartz bi-pin
M12= MR16 halogen,
12V-12W,
M20= MR16 halogen,
12V, 24V-20W
M35= MR16 halogen,
12V, 24V-35W
M50= MR16 halogen,
12V, 24V-50W
MH20= MR16-IR 12V-20W,
high-output
MH35= MR16-IR, 12V-35W,
high-output
MH50= MR16-IR 12V-50W,
high-output
Blank= no sign
-P1= s ingle
face LED
pictogram
-P2= d
ouble
face LED
pictogram
E xample : L D X 6 - 7 2 E X P / 1 1 S 2 1 2 - P 1
81
AC voltage
Blank= 120VAC
U277= 277VAC
U347= 347VAC
options
Blank= no
options
D3= time delay
(15 mins.)
TP= transfer
panel
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® LDX-EXP-E Series of hazardous location battery unit equipment. The battery
unit housing will be constructed of Die-Cast aluminum with grey epoxy powder coat finish. The equipment
shall be rated for 120, 277 or 347V, 60 Hz input and be CSA listed. The equipment shall have an output of
V and
W and shall supply the rated load for minimum of 1/2 hour to 87.5% of the
rated battery voltage. The battery shall be a long-life, maintenance-free Lead-Calcium type. The charger shall
be fully computer tested and have its charge voltage set in the factory to ± 1% tolerance. The charger shall be
current limited, temperature compensated, short circuit proof and reverse polarity protected. The charger shall
be furnished with an electronic lockout circuit, which will connect the battery when the AC circuit is activated,
and an electronic brownout circuit, which will activate the emergency heads when the utility power dips below
75% of nominal voltage. Where required the equipment shall come complete with
heads, each
of them equipped with
lamp(s) of
W. The head housing shall be Die-Cast aluminum
with grey epoxy powder coat finish. The lenses shall be a clear, impact and heat resistant prismatic glass globe.
The head shall be factory sealed, with no need for external seals. Where required the equipment shall come
complete with one Exit Sign and will include a transfer panel to maintain the Exit Sign permanently lighting in
both normal and emergency operation. The exit housing shall be industrial grade 14-gauge steel and finished
in grey enamel. The faceplate will be constructed of heavy-duty 14-gauge steel and feature universal knockout
chevrons and the red letters shall not be less than 6” in height with a 3/4” stroke. The sign shall include an
LED lamp with ALINGAP LEDs and shall consume less than 5W in either AC or battery mode.
, Division
, Group
. The Exit Sign shall be CSA-C860
The equipment shall be suitable for Class
approved and meets CSA C22.2 No.141
The equipment shall be Ready-Lite® Model:
.
LDX-EXP-E Series
Battery Units,
Self-powered Exit Signs
& Combination Units
CSA certified for use in
hazardous locations
The LDX-EXP-E Series of battery equipment is
designed to cover emergency lighting applications for the entire spectrum of hazardous
locations, where flammable gases, vapors,
liquids, dust particles, fabrics or tissues are
permanently present or are likely to exist.
In one simple-to-order catalogue family the
LDX-EXP-E Series combines three traditional
emergency lighting products with battery
back-up: battery units with emergency
lights, Self-powered Exit Signs, and combination units with emergency lights and Exit
Sign. The equipment is also available with
additional emergency power capacity to
drive remote heads and Exit Signs.
POwer consumption and unit rating
Model
LDX636EXP
LDX672EXP
LDX6108EXP
LDX1272EXP
LDX12144EXP
LDX12200EXP
LDX24144EXP
LDX24288EXP
Features
• CSA Certified for use in hazardous
locations:
- Class I, Divisions 1 and 2, Groups
A, B, C, D
- C
lass II, Divisions 1 and 2, Groups
E, F, G
- Class III, Divisions 1 and 2
• D
ie-Cast aluminum body with grey
epoxy powder coat finish; clear, impact
and heat resistant prismatic glass globe
• L ong-life, maintenance-free
Lead-Calcium battery
• Battery charger is current limited,
temperature compensated, short-circuit
proof and reverse polarity protected
• Emergency heads with one or twin
lamp design
• Self-powered combo includes a transfer
panel to drive four remote LED-based
remote Exit Signs
• Exit Sign uses an LED lamp with
ALINGAP LEDs
• The Self-powered version is CSA C22.2
No. 141 certified
AC Specs
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
120/347VAC
30min
1h00
36
72
108
72
144
200
144
288
21
42
63
42
84
117
84
168
Wattage capacity
1h30
2h00
15
30
45
30
60
83
60
120
4h00
12
24
36
24
48
67
48
96
6
12
18
12
24
33
24
48
NOTE: The wattage capacity applies only to the battery unit. For combo or Self-powered Exit Signs one must allocate 5W of emergency
power for each sign.
n
Temperature codes: measured at 40°C Ambient
Explosion-proof equipment is composed of one or more modules, each of them qualified for a specific temperature code. The temperature code of the complete equipment (enclosure + exit sign + emergency heads)
is defined as the most severe of the temperature codes identified for each of the modules below.
1. temperature codes for LDX-EXP-E Series (battery unit enclosure)
Severity Code
S1, S1A
S2
S3, S3A
S4
Temperature Code
T6
T6
T6
T6
2. temperature codes for Rfx-ex Series* (exit sign)
Severity Code
S1
S2
S3
S4
Temperature Code
T6
T6
T4A
T6 (E, F, G)
*Self-Powered Exit Sign only (no heads).
3. temperature codes for RFX Series (emergency heads)
Severity
Code
Quartz bi-pin
12W, 20W
MR16
12V-12W
MR16
12V, 24V-20W
MR16
12V, 24V-35W
MR16
12V, 24V-50W
MR16
120V-20W
MR16
120V-35W
MR16
120V-50W
S1
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
S2
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
S3
T1 (450
T4 (450
T3 (200
S4
o
C)
T4A (120o C)
(E,F,G)
o
C)
T5 (100o C)
(E,F,G)
82
o
C)
T5 (100o C)
(E,F,G)
T2 (300
o
C)
T4A (120o C)
(E,F,G)
T1 (450
o
C)
T3C (160o C)
(E,F,G)
T2D (215
o
C)
T4A (120o C)
(E,F,G)
T2 (300
o
C)
T3C (160o C)
(E,F,G)
T1 (450o C)
N/A
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
SMALL CABINET (36-72W)
20-7/8” [53 cm]
Battery Units,
Self-powered Exit Signs
& Combination Units
22-7/8” [58.2 cm]
19-5/8” [50 cm]
22-7/8” [58.2 cm]
18-1/4” [46.5 cm]
LDX-EXP-E Series
6-3/8” [16.3 cm]
9-5/8” [24.4 cm]
19-5/8” [50 cm]
10-3/8” [26.4 cm]
27-3/4” [70.5 cm]
14-3/8” [36.6 cm]
LARGE CABINET (108-288W)
21-1/4” [53.9 cm]
23-3/4” [60.4 cm]
23-3/8” [59.2 cm]
20-1/8” [51 cm]
23-3/8” [59.2 cm]
8-1/4” [20.8 cm]
10” [25.4 cm]
20-1/8” [51 cm]
13-1/8” [33.3 cm]
30-5/8” [77.8 cm]
14-3/8” [36.6 cm]
Ordering Information
Identify the environment of your application: Class
, Division
Refer to table 4 for the Severity Code to use in your catalogue number.
n
, Group
.
4. severity code Selection chart
Environment
Severity Code
Cl. I, Div. 1, Gr. A*
S1A
Cl. I, Div. 1, Gr. B
S1
Cl. I, Div. 1, Gr. C, D
S2
CI. I, Div. 2, Gr. A*
S3A
CI. I, Div. 2, Gr. B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G
Cl. III, Div. 1 & 2
S4
*Units for Class I Group A are not available with test switch and pilot light.
Ordering chart
dc
voltage
LDX6= 6V
capacity
cabinet size
-36= 36W (S)*
-72= 72W (S)*
-108= 108W (L)*
Series
EXP
LDX12= 12V -72= 72W (S)*
-144= 144W (L)*
-200= 200W (L)*
LDX24= 24V -144= 144W (L)*
-288= 288W (L)*
*Cabinet size
not part of
nomenclature
head style
Blank= no
heads
/11= single
remote,
1 lamp
/12= single
remote,
2 lamps
/21= double
remote, 1
lamp each
n
Severity code
S1A= CL.I, Div.1, Gr. A*
S1= CL.I, Div.1, Gr. B
S2= CL.I, Div.1, Gr. C, D
S3A= CL.I, Div.2, Gr. A*
S3= CL.I, Div.2, Gr. B, C, D
S4= CL.II, Div.1, & 2
Gr. E, F, G
CL.III, Div.1 & 2
*Sold without test switch or
pilot light
E xample : L D X 6 - 3 6 E X P / 1 1 S 1 1 2 - E 1
83
lamps
faces
Blank= no lamp
-E1= s ingle face
12= 6V, 12V - 12W,
exit Sign,
quartz bi-pin
C860 LED
20= 6V to 24V-20W,
-E2= d
ouble face
quartz bi-pin
exit sign,
M12= MR16 halogen,
C860 LED
12V-12W,
M20= MR16 halogen,
12V, 24V-20W
M35= MR16 halogen,
12V, 24V-35W
M50= MR16 halogen,
12V, 24V-50W
MH20= MR16-IR 12V-20W,
high-output
MH35= MR16-IR, 12V-35W,
high-output
MH50= MR16-IR 12V-50W,
high-output
AC voltage
options
Blank= 120VAC
U277= 277VAC
U347= 347VAC
Blank= no
options
D3= time delay
(15 mins.)
TP= transfer
panel
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® LDX-EXP-S Series of hazardous location battery unit equipment. The battery
unit housing will be constructed of Die-Cast aluminum with grey epoxy powder coat finish. The equipment
shall be rated for 120, 277 or 347V, 60 Hz input and be CSA listed. The equipment shall have an output of
V and
W and shall supply the rated load for a minimum of 1/2 hour to 87.5% of the
rated battery voltage. The battery shall be a long-life, maintenance-free Lead-Calcium type. The charger shall
be fully computer tested and have its charge voltage set in the factory to ± 1% tolerance. The charger shall be
current limited, temperature compensated, short circuit proof and reverse polarity protected. The charger shall
be furnished with an electronic lockout circuit, which will connect the battery when the AC circuit is activated,
and an electronic brownout circuit, which will activate the emergency heads when the utility power dips below
75% of nominal voltage. Where required the equipment shall come complete with
heads, each
of them equipped with
lamp(s) of
W. The head housing shall be Die-Cast aluminum
with grey epoxy powder coat finish. The lenses shall be a clear, impact and heat resistant prismatic glass globe.
The head shall be factory sealed, with no need for external seals. Where required the equipment shall come
complete with one Exit Sign and will include a transfer panel to maintain the Exit Sign permanently lighting in
both normal and emergency operation. The exit housing shall be industrial grade 14-gauge steel and finished
in grey enamel. The faceplate will be constructed of heavy-duty 14-gauge steel and feature universal knockout
chevrons and the red letters shall not be less than 6” in height with a 3/4” stroke. The sign shall include an
LED lamp with ALINGAP LEDs and shall consume less than 5W in either AC or battery mode.
, Division
, Group
The Exit Sign shall be CSA-C860 and
The equipment shall be suitable for Class
approved and meet CSA C22.2 No. 141
ldx-EXP-s
Series
Battery Units, Self-powered
“Sortie” Signs Combo Units
CSA certified for use in
hazardous locations
The LDX-EXP-S Series of battery equipment
is designed to cover emergency lighting
applications for the entire spectrum of
hazardous locations, where inflammable
gases, vapors, liquids, dust particles, fabrics
or tissues are permanently present or are
likely to exist.
In one simple-to-order catalogue family the
LDX-EXP-S Series combines three traditional
emergency lighting products with battery
back-up: battery units with emergency
lights, Self-powered Sortie Signs, and combination units with emergency lights and
Sortie Sign. The equipment is also available
with additional emergency power capacity to
drive remote heads and Sortie Signs.
The equipment shall be Ready-Lite® Model:
POwer consumption and unit rating
Model
AC Specs
LDX636EXP
LDX672EXP
LDX6108EXP
LDX1272EXP
LDX12144EXP
LDX12200EXP
LDX24144EXP
LDX24288EXP
Features
• CSA Certified for use in hazardous
locations:
- Class I, Divisions 1 and 2, Groups
A, B, C, D
- C
lass II, Divisions 1 and 2, Groups
E, F, G
- Class III, Divisions 1 and 2
• D
ie-Cast aluminum body with grey
epoxy powder coat finish; clear, impact
and heat resistant prismatic glass globe
• Long life, maintenance-free,
Lead-Calcium battery; charger is current
limited, temperature compensated,
short-circuit proof and reverse polarity
protected
• Emergency heads with one or twin
lamp design
• Sortie Sign is CSA C860 certified
• Self-powered combo includes a transfer
panel to drive four LED-based remote
Sortie Signs
• Sortie Sign uses a LED lamp with
ALINGAP LEDs
• The Self-powered version is CSA C22.2
No. 141 certified
.
120/347VAC
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
30min
1h00
36
72
108
72
144
200
144
288
21
42
63
42
84
117
84
168
Wattage capacity
1h30
2h00
15
30
45
30
60
83
60
120
4h00
12
24
36
24
48
67
48
96
6
12
18
12
24
33
24
48
NOTE: The wattage capacity applies only to the battery unit. For combo or Self-powered Sortie Signs one must allocate 5W of emergency
power for each sign.
n
Temperature codes: measured at 40°C Ambient
Explosion-proof equipment is composed of one or more modules, each of them qualified for a specific temperature code. The temperature code of the complete equipment (enclosure + exit sign + emergency heads)
is defined as the most severe of the temperature codes identified for each of the modules below.
1. temperature codes for LDX-EXP-S Series (battery unit enclosure)
Severity Code
S1, S1A
S2
S3, S3A
S4
Temperature Code
T6
T6
T6
T6
2. temperature codes for Rfx-CS Series* (Sortie sign)
Severity Code
S1
S2
S3
S4
Temperature Code
T6
T6
T4A
T6 (E, F, G)
*Self-Powered Sortie Sign only (no heads).
3. temperature codes for RFX Series (emergency heads)
Severity
Code
Quartz bi-pin
12W, 20W
MR16
12V-12W
MR16
12V, 24V-20W
MR16
12V, 24V-35W
MR16
12V, 24V-50W
MR16
120V-20W
MR16
120V-35W
MR16
120V-50W
S1
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
S2
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
S3
T1 (450
T4 (450
T3 (200
S4
o
C)
T4A (120o C)
(E,F,G)
o
C)
T5 (100o C)
(E,F,G)
84
o
C)
T5 (100o C)
(E,F,G)
T2 (300
o
C)
T4A (120o C)
(E,F,G)
T1 (450
o
C)
T3C (160o C)
(E,F,G)
T2D (215
o
C)
T4A (120o C)
(E,F,G)
T2 (300
o
C)
T3C (160o C)
(E,F,G)
T1 (450o C)
N/A
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
ldx-EXP-s
Series
SMALL CABINET (36-72W)
6-1/8” [15.7 cm]
29-1/2” [70.5 cm]
22-1/2” [57.3 cm]
17-1/8” [43.6 cm]
22-7/8” [58.2 cm]
19-5/8” [50 cm]
22-7/8” [58.2 cm]
19-5/8” [50 cm]
9-5/8” [24.4 cm]
10-3/8” [26.4 cm]
Battery Units, Self-powered
“Sortie” Signs Combo Units
14-3/8” [36.6 cm]
LARGE CABINET (108-288W)
20-1/8” [51 cm]
23-3/8” [59.2 cm]
21-1/4” [53.9 cm]
23-3/8” [59.2 cm]
8-1/4” [20.8 cm]
10” [25.4 cm]
20-1/8” [51 cm]
13-1/8” [33.3 cm]
33-1/2” [84.9 cm]
26-5/8” [67.6 cm]
14-3/8” [36.6 cm]
Ordering Information
Identify the environment of your application: Class
, Division
Refer to table 4 for the Severity Code to use in your catalogue number.
n
, Group
.
4. severity code Selection chart
Environment
Severity Code
Cl. I, Div. 1, Gr. A*
S1A
Cl. I, Div. 1, Gr. B
S1
Cl. I, Div. 1, Gr. C, D
S2
CI. I, Div. 2, Gr. A*
S3A
CI. I, Div. 2, Gr. B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G
Cl. III, Div. 1 & 2
S4
*Units for Class I Group A are not available with test switch and pilot light.
3. LDX-EXP-s
DC
voltage
LDX6= 6V
capacity
cabinet size
-36= 36W (S)*
-72= 72W (S)*
-108= 108W (L)*
Series
EXP
LDX12= 12V -72= 72W (S)*
-144= 144W (L)*
-200= 200W (L)*
LDX24= 24V -144= 144W (L)*
-288= 288W (L)*
*Cabinet size
not part of
nomenclature
head style
and wattage
Blank= no heads
/11= single
remote, 1
lamp
/12= single
remote, 2
lamps
/21= double
remote, 1
lamp each
n lamps
Severity code
S1A= CL.I, Div.1, Gr. A*
S1= CL.I, Div.1, Gr. B
S2= CL.I, Div.1, Gr. C, D
S3A= CL.I, Div.2, Gr. A*
S3= CL.I, Div.2,
Gr. B, C, D
S4= CL.II, Div.1, & 2
Gr. E, F, G
CL.III, Div.1 & 2
*Sold without test switch or
pilot light
faces
Blank= no lamp
Blank= no exit sign
12= 6V, 12V - 12W,
S1= single face sortie,
quartz bi-pin
C860 LED
20= 6V to 24V-20W,
S2= double face
quartz bi-pin
sortie, C860 LED
M12= MR16 halogen,
12V-12W,
M20= MR16 halogen,
12V, 24V-20W
M35= MR16 halogen,
12V, 24V-35W
M50= MR16 halogen,
12V, 24V-50W
MH20= MR16-IR 12V-20W,
high-output
MH35= MR16-IR, 12V-35W,
high-output
MH50= MR16-IR 12V-50W,
high-output
EXAMPLE: LDX6-144EXP/11S320S2D3
85
AC voltage
options
Blank= 120VAC
U277= 277VAC
U347= 347VAC
Blank= no
options
D3= time delay
(15 mins.)
TP= transfer
panel
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Wire guards
Features
wall mount
460.0027-RL
end mount
460.0028-RL
ceiling mount
Dimensions
Dimensions are approximate and subject to change.
14” [32.58cm]
[35.5
cm] [32.58cm]1” [2.5 cm]
15.5”12.38”
[39.37cm]
12.38”
1” [2.5cm]
Ordering information: Exit or sortie Sign
Series
life years
RX10= exit sign, single face, universal mount
and chevrons
RX20= exit sign, double face, universal mount
and chevrons
RS10= sortie sign, single face, universal
mount and chevrons
RS20= sortie sign, double face, universal
mount and chevrons
10= 10 years (exit only)
12= 12 years (sortie only)
20= 20 years (exit only)
housing colours
background colours
G= grey*
Blank= white*
B= black
Blank= red
G= green*
* Not available in Sortie
* Not available in Sortie
Options
-AF = aluminum frame
-PC = p
olycarbonate shield
-VR = vandal cover
NEW
-N
EXAMPLE: RX1010-AF-N
Ordering information: pictogram sign
Series
RT= pictogram sign
FaceS
1 = s ingle face universal mount and
chevrons
2=d
ouble face universal mount and
chevrons
housing colours
W= white
B= black
G= grey
life years
10= 10 years
EXAMPLE: RT1W10AF
Options
AF = aluminum frame
PC = p
olycarbonate shield
VR = vandal cover
Unlike Exit or Sortie, the Pictogram Sign is not available in double arrow configuration.
86
12.38”
12.38”
[32.5
[32
8.35 [21.21cm]
8.35 [21.21cm]
8.56 [21.74cm]
1” [2.5 cm]
1” [2.5cm]
8.35 [21.21cm]
12-7/8”
[32.6 cm]
12.38” [32.58cm]
15.5” [39.37cm]
1”
cm]
1” [2.5
[2.5cm]
8.56 [21.74cm]
15-1/2”
[39.4 cm]
15.5” [39.37cm]
8.56 [21.74cm]
8-1/2”
[21.7 cm]
• Illumination provided by borosilicate
glass tubes, internally coated with zinc
sulphide phosphor and filled with
tritium gas
• Minimum brightness at time of
manufacture is 0.132 foot-lambert
(0.452 cd/m2)
• Decorative, slim-line heavy-duty ABS
housing
• Rugged, impact-resistant polycarbonate
face
• Spark-free construction
• Simple installation – universal
direction capability, comes complete
with universal mounting hardware
• Stands up to extreme temperatures
in outdoor or indoor applications
• Life expectancy of 10 or 20-year
(EXIT), 12-year (SORTIE) and 10-year
(Pictogram)
• Available in single or double face
• Certified to standard UL924
(ULC-S572)
• Pictogram Sign includes universal
stencils (straight from here, left from
here and right from here)
460.0079-RL
8-1/4”
[21 cm]
8.35 [21.21cm]
Power-Free Pictogram, Exit
or “Sortie” Sign
8.35 [21.21cm]
8-1/4”
[21 cm]
RT Series
Supply and install Ready-Lite® RX10 (EXIT) or RS10 (SORTIE) or RT (PICTOGRAM) Series Self-Luminous Exit
Signs. The Exit Sign shall be constructed of a thermoplastic housing and be corrosion proof. The sealed housing
will incorporate no loose or removable parts allowing for easy installation. The standard minimum guaranteed
life will be 10 years. The standard mounting brackets will allow for either end/ceiling or wall mount. Standard
“Exit” and “Sortie” Signs shall be supplied with white letters that are 6” high by 3/4” stroke. The initial average
minimum brightness shall be 0.132 foot-lambert (0.452 cd/m2).
The equipment shall be Ready-Lite® Model:
.
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
Custom-worded, illuminated signage is available using the same sturdy construction and electrical design
as Ready-Lite® Exit Signage.
A wide range of sign body options and colour choices are available to suit any application.
Contact your local Ready-Lite® sales representative to discuss your specific requirements.
Special Wording
Illuminated Signage
examples
Features
• The same sturdy construction and
electrical design used in our Exit Signs
is used to produce our custom-worded,
illuminated signage
• Sign bodies - steel, extruded and
Die-Cast aluminum, weatherproof,
flame-retardant polycarbonate, recessed
housing
• Also available with Self-powered
canopy and with emergency lamps
• Custom wording – any style of lettering,
any language, any alphabet, any
special characters
• Graphics – logos, standard symbols,
custom art
• Colour choices – sign bodies, message,
faceplate panel
• Illumination – LED (light-emitting
diodes) – other light sources
available - consult representative
• White-out, black-out and split picture
options
WHITE-OUT OPTION
NON-ILLUMINATED
BLACK-OUT OPTION
ILLUMINATED
NON-ILLUMINATED
When the sign is non-illuminated the acrylic panel in the faceplate appears blank
white. The message appears only when the sign is illuminated.
ILLUMINATED
When the sign is non-illuminated the acrylic panel in the faceplate appears black.
The message appears only when the sign is illuminated.
87
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
how much can you save?
The following is an example of the savings you can generate by simply installing an LED retrofit kit in an existing
incandescent Exit Sign.
LED Retrofit Kits
Convert high-consumption
incandescent and
fluorescent lamps to
energy-efficient LED
lamps
Converting existing Exit Signage from
incandescent or fluorescent lamps to LED
(light emitting diodes) lamps drastically
reduces operating and maintenance costs
for building owners and property managers.
As part of energy-efficiency programs, some
Canadian electric utilities are also actively
promoting conversion to LED with incentive
and rebate programs for installers and
building owners/managers.
Features
your Payback Analysis
The Retrofit Kit Cost:
Installation cost (per unit) for a
retrofit kit (Labour):
Wattage rating per incandescent lamp in existing fixture:
Number of incandescent lamps per fixture:
Wattage rating of Ready-Lite MB1UN retrofit kit:
My existing incandescent exit lamps last for:
Benefits of using LED lamps in Exit Signs:
• Exceptional energy-efficiency – reduces
energy consumption by up to 90%
• Extremely long life – 10 to 25 years
• Important reduction in maintenance
and energy costs
• Average payback is less than two years
• Retrofit kits are easy to install
• Improved visibility and reliability:
ALINGAP LED technology
$5.00
15W
2
1.7W
4 Months
My replacement labour cost:
$25.00/Hour
Estimated lamp replacement
time per exit:
20 Minutes
Current material cost for each
Exit Sign lamp:
$1.00/Lamp
My current energy cost:
Ready-Lite® offers four retrofit kit options; all
based on the long-life ALINGAP LED technology:
• SB Series
• Mini-Bar Series
• Mini-Bar “D” Series
• RLB Bulb Series
$70.00
The PAYBACK FOR YOUR INSTALLATION IS:
THE ANNUAL RETURN ON INVESTMENT IS:
ANNUAL SAVINGS:
For more information, please consult your sales representative.
88
$0.060/$ Per kWh
1.06 Years
94.50 %
$70.87
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
mini-bar “D” Series
dimensions
Dimensions are approximate and subject to change.
m]
13/16” [2.1 cm]
4.1 c
2” [2
9-1/
LED Retrofit Kits
mini-bar “D” Series
features
• Easiest to install in its class
• Compact size makes it ideal for virtually
all Exit Signs
• Can be retrofitted directly on
fluorescent ballast
• Suitable for all AC line applications
including Exit Signs equipped with
in-line diodes
• Long-life, energy-efficient ALINGAP
LED techonology
13/16” [3 cm]
Power consumption
Model
AC Specs
MB*D
DC Specs
120VAC; 120VAC with in-line diodes
2.8W
N/A
N/A
ordering information
Series
voltage
MB= for
standard
applications
1= 120VAC
model
D= with or without
inline diodes, high
brightness
options
C= candelabra
I= intermediate
M= medium
B= bayonet
CIMB= complete set of bases
EXAMPLE: MB1DC
mini-bar Series
features
mini-bar Series
• E asiest to install in its class
• C ompact size makes it ideal for
virtually all Exit Signs
• C an be retrofitted directly on
fluorescent ballast
• Long-life, energy-efficient red ALINGAP
LED technology
• Available with AC adaptor for all types
of lamp sockets
• 10 year limited warranty
dimensions
Dimensions are approximate and subject to change.
24.1
2” [
9-1/
cm]
13/16” [2.1 cm]
1-3/16” [3 cm]
Power consumption
Model
MB
AC Specs
120VAC; 86VAC step down from 347VAC
DC Specs
0.65W
N/A
N/A
ordering information
Series
MB
voltage
1= 120VAC
2= 277VAC (hardwire)
3= 347VAC (hardwire)
4= 240VAC (hardwire)
options
C= candelabra
I= intermediate
M= medium
B= bayonet
F= G23 compact fluorescent
UN= c omplete set of bases (excludes “F”
base)
EXAMPLE: MB1C
89
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
rlb bulb
dimensions
Dimensions are approximate and subject to change.
15/16” [2.5 cm]
4-3/4” [12 cm]
3-3/4” [9.6 cm]
5-1/3” [13 cm]
3-3/4” [9.6 cm]
LED Retrofit Kits
1-1/4” [3.2 cm]
RLB BULB Series
features
• Quick and easy to install
• Available with a wide range of lamp
bases for quick lamp to lamp
replacement
• Long-life, energy-efficient ALINGAP
LED techonology
• 120VAC or 120VAC with in-line diode
1-3/16” [2.1 cm]
13/16” [2.1 cm]
Power consumption
Model
AC Specs
DC Specs
RLBH
120VAC
0.90W
RLBD
120VAC
2.6W
N/A
120VDC
N/A
2.6W
ordering information
Series
BASE
RLBH= standard version
RLBD= with or without in-line diodes (2.5W), high
brightness
-C= candelabra
-I= intermediate
-M= medium
-B= bayonet
-F= G23 compact fluorescent (not available for RLBD)
EXAMPLE: RLBH-C
SB Series features
• Quick and easy to install
• Long-life, energy-efficient red ALINGAP
LED technology
• Module features two independent
circuits – one for AC input; one for
DC input
• Universal AC input: 120/277/347VAC;
universal two-wire DC input: 6 to 24VDC
• Power consumption of 1.1W per
module
• 10 year limited warranty
SB series
dimensions
Dimensions are approximate and subject to change.
m]
8.3 c
8” [2
/
11-1
13/16” [2.1 cm]
1-3/16” [3 cm]
Power consumption
Model
SB
AC Specs
120/277/347VAC
DC Specs
1.1W
6 to 24VDC
1.3W
ordering information
Series
SB= hardwire retrofit kit
voltage
-LU= 1
20/277/347VAC, 6/12/24VDC
-LU36= 1
20/277/347VAC, 36VDC
-LU48= 120/277/347VAC, 48VDC
-LU120= 120/347VAC, 120VDC
-L120-2W= 1
20VAC,120VDC, 2 wires
EXAMPLE: SB-LU
90
Options
Blank= 11.0” (28 cm) long
-9.5= 9.5” (24 cm) long*
*Available in -LU voltage only.
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
Offered in a variety of colours and lengths, Ready-Lite® Pendant Kits are designed to facilitate the installation
of Exit Signs at regular mounting heights.
Compatible with both horizontal and sloped ceilings, these Pendant Kits is truly universal and will adapt to
any application.
Please consult your sales representative.
Pendant Kit
Dimensions
Dimensions are approximate and subject to change.
P3R
Length
P1R
P2R
P4R
ordering information
Series
length (in)*
colour
P1R
standard model of pendant
6
12
18
24
W= white
B= black
SG= silver grey
P2R
Legend™ series
6
12
18
24
W= white
B= black
SG= silver grey
P3R
Aluminum slim edge-lit
6
12
18
24
W= white
B= black
SG= silver grey
P4R
Ultima™ plastic exit
6
12
18
24
W= white
B= black
SG= silver grey
*Other lengths available by request. Consult your sales representative.
91
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
exit signs
part #
wire guards &
Mounting
shelves
mounting
dimensions
signs
w
h
d
End Mount
CX2000
CX5000
TUF
ULTD
RA
RT
CX4000
NEXTN
RN
RS1000
RS
RP
ULT
RX
10-1/2”
(26.7 cm)
6” (15.2 cm)
16”
(40.6 cm)
460.0028-RL
Ceiling
Mount
CX2000
CX5000
TUF
RT
ULTD
RA
RP
CX4000
NEXTN
RN
RS1000
RS
ULT
RX
14-1/2”
(36.8 cm)
6-1/4”
(15.9 cm)
10-1/2”
(26.5 cm)
460.0034-RL
Wall Mount
LD12-S Sortie
CX9000BIL
CS9000BIL
LD12E (Large)
LD6-IF
28-1/8”
(71.5 cm)
21-1/8”
(53.7 cm)
10”
(25.4 cm)
460.0048-RL
End Mount
CS2000
CS5000
CS4000
CNESTU
10-1/2”
(26.7 cm)
6”
(15.2 cm)
21”
(53.3 cm)
460.0057-RL
Wall Mount
CS2000
CS5000
CS4000
CNESTU
20-3/4”
(52.7 cm)
10”
(25.4 cm)
4”
(10.2cm)
460.0058-RL
Ceiling
Mount
CS2000
CS5000
CS4000
CNESTU
21-3/4”
(55.2 cm)
5-1/2”
(14 cm)
10-1/2”
(26.7cm)
460.0059-RL
Wall Mount
CX7000
CNSXTN
31”
(86.4 cm)
10”
(25.4 cm)
4-1/2”
(14 cm)
460.0060-RL
End Mount
RAC
SM-NEXTN
SM-CX5000
20”
(50.8 cm)
12”
(30.5 cm)
15”
(38.1 cm)
460.0060-RL
Ceiling
Mount
R-SN
ULT Combo
N-TUF
RH
TUF-HZ
20” (50.8
cm)
12”
(30.5 cm)
15”
(38.1 cm)
460.0078-RL
Wall Mount
RNC
Ultima™ Combo
18”
(45.7 cm)
18”
(45.7 cm)
7”
(17.8 cm)
NEXTN
Ultima™ Exit
RN
RS
RS1000
ULTD
14-1/4”
(36.2 cm)
9-7/8”
(25.0 cm)
4-5/8”
(11.7 cm)
TUFHZ
RSC
RAC
15-1/4”
(38.7 cm)
14-1/8”
(35.9 cm)
6-1/2”
(16.5 cm)
460.0027-RL
CX4000BIL
CS4000BIL
CNEXTN
CS7000
N-TUF
RNC
RSC
RNC
SM-CX5000
SM-CS5000
SM-NEXTN
RAC
RSC
N-TUF
RHC
HZ
CX2000
CX5000
TUF
RT
CX4000
RP
RA
SM-NEXTN
SM-CX5000
RH
460.0079-RL
Wall Mount
460.0080-RL
Wall Mount
460.0081-RL
Wall Mount
SM-CS5000, CS9000N,
LD12E (Small), R-SN
20”
(50.8 cm)
17-1/8”
(43.6 cm)
8-1/2”
(21.6 cm)
460.0091-RL
Wall Mount
CX5000R
15”
(38.1 cm)
10-1/2”
(26.7 cm)
1”
(2.5 cm)
460.0092-RL
Ceiling
Mount
31”
(53.3 cm)
4.5”
(11.4 cm)
10”
(25.4 cm)
460.0104-RL
Ceiling
Mount
25”
(63.5 cm)
10”
(25.4 cm)
20”
(50.8 cm)
CS4000BIL
CX4000BIL
CNEXTN
CX7000
CNSXTN
CS7000
LD6-IF, CS9000N,
CX9000BIL, CS9000BIL
92
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Battery Units
part
mounting
commercial,
deco unit
460.0078-RL
Wall Mount
460.0081-RL
dimensions
w
h
d
“A” Cabinet-6V, 12V,
24V-Max. 144W
17” (45.7 cm)
17” (45.7 cm)
7” (17.8 cm)
Wall Mount
“B” Cabinet-6V-180W
12V-216 to 360W
24V-200 to 288W
20” (50.8 cm)
17-1/8” (43.6 cm)
8-1/2” (21.6 cm)
460.0034-RL
Wall Mount
“C” Cabinet
24V-350 to 720W
28-1/8” (71.5 cm
21-1/8” (53.7 cm)
10” (25.4 cm)
460.0097-RL
Wall or
Ceiling
Mount
LDX-VQ
31”(53.3 cm)
7”(17.8 cm)
6”(15.2 cm)
460.0080-RL
Wall Mount
LDXC, LDXA, Ultima
15-1/4”
(38.7 cm)
14-1/8” (35.9 cm)
6-1/2” (16.5 cm)
460.0010-RL
Wall or
Ceiling
Mount
C29, B29
14” (35.6 cm)
5.8” (14.7 cm)
5.6” (14.2 cm)
wire guards
& mounting
shelves
Industrial
460.0082-RL
Wall Mount
Small Cabinet
12” (30.5 cm)
9” (3.5 cm)
9” (3.5 cm)
460.0081-RL
Wall Mount
Medium and Large
Cabinet
20” (50.8 cm)
17-1/8” (43.6 cm)
8-1/2” (21.6 cm)
460.0105-RL
Wall or
Ceiling
Mount
IPR 48”
54.6’ (138.68 cm)
8’ (20.32 cm)
5’ (12.7 cm)
IPR 24”
30’ (76.2 cm)
8’ (20.32 cm)
5’ (12.7 cm)
460.0106-RL
Remote Heads
dimensions
part #
Remote Heads
W
H
D
460.0029-RL
TUF-NM, RT, RQ, RM, RL25, VQ,
RL40M, RL150
8-1/4” (21.5 cm)
6-1/4” (15.9 cm)
6-3/4” (17.2 cm)
460.0031-RL
VQW, WT2, LH2
25-1/4” (64.1 cm)
8-1/2” (21.5 cm)
8-1/2” (21.5 cm)
460.0032-RL
VQ2, RL150D
9-1/2” (24.1 cm)
9-1/2” (24.1 cm)
6-1/8” (15.6 cm)
460.0033-RL
RF105
9-1/2” (24.1 cm)
9-1/2” (24.1 cm)
4”(10.2 cm)
460.0035-RL
LT, WT, WSR
8-1/4” (21.5 cm)
6-1/4”(15.9 cm)
8-1/2” (21.5 cm)
460.0082-RL
LQ2, WT2, WSR2,
Guardian™, Cadilite™
12”(30.5 cm)
9”(22.9 cm)
9”(22.9 cm)
460.0078-RL
Triple Remote
17”(45.7 cm)
17”(45.7 cm)
7”(17.8 cm)
Mounting Shelves
Part # 440.0620-RL for “B” Cabinet
7-1/2”
(19.05 cm)
8-1/32”
(20.4 cm)
11-5/16” (28.7 cm)
15-1/16” (38.28 cm)
5-1/16”
(12.89 cm)
8-1/32”
(20.4 cm)
11-1/32” (28.02 cm)
7-1/2”
(19.05 cm)
10-29/32” (27.69 cm)
Part # 440.0625-RL for “C” Cabinet
11-1/16” (28.07 cm)
Part # 440.0616-RL for “A” Cabinet
6-3/16”
(15.75 cm)
18-1/16” (45.85 cm)
93
25-3/32” (63.75 cm)
6-3/16”
(15.75 cm)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
The EZ2™ Canopy allows the installer to make all of the electrical connections using both hands without having
to juggle with the Exit Sign, making it our most contractor friendly product feature to date.
Simply attach the backplate to the junction box, clip the canopy on the Exit Sign, hang the canopy on the
back plate, make your connections using both hands, slide the unit in place, one screw and the job is done!
EZ2™ Canopy
dimensions
Dimensions are approximate and subject to change.
Quick and Easy Installation
6-3/8”
1-1/32”
4-11/16”
See detail A
See detail C
See detail B
3. Connect the wires, then align and slide
the sign to its final position.
1. Attach the backplate/spider to the
wall before assembly.
2. Hang the unit using
the tabs and the wire eyes.
Detail A
Scale 3.000
Detail B
Scale 3.000
94
Detail C
Scale 3.000
AD
Auto-Diagnostics,
audible
Automatically tests and continuously monitors your emergency lighting unit. If
a problem occurs, the unit will send a visual (flashing or blinking LED indicator)
and audible warning. Complies with Fire Code requirements.
ADN
Auto-Diagnostics,
non-audible
Automatically tests and continuously monitors your emergency lighting unit. If
a problem occurs, the unit will send a visual (flashing or blinking LED indicator)
warning. Complies with Fire Code requirements.
CW1
Cold weather,
120VAC
120VAC input cold weather protection feature for applications where
temperatures can reach -40° C.
CW3
Cold weather,
347VAC
347VAC input cold weather protection feature for applications where
temperatures can reach -40° C.
Time delay
Same as the D3 option but can be programmed for 5, 10, 15 or 20 minutes
delay.
D3
15 minutes time
delay
Normally, when the A.C. is restored, all emergency lighting lamps are turned
off. However, in some cases such as when metal halide lamps are used, it is
possible that the general lighting will not be available for several minutes after
the blackout (or brownout) period. Battery units with the D3 option will keep
some energy in store to ensure that the emergency lighting stays on or comes
back on for at least 15 minutes once the regular A.C. power has been restored.
NEX
NEXUS wired
system interface
The NEXUS® system interface is a computerized maintenance system for
emergency lighting that, once programmed, will perform the tests, keep written
records and send notification if anything needs to be fixed. One full system
can address hundreds of units in as many buildings as you need from a single
location.
NEXRF
NEXUS® wireless
system interface
The NEXUS® wireless system interface is a computerized maintenance system
for emergency lighting that, once programmed, will perform the tests, keep
written records and send notification if anything needs to be fixed. One full
system can address hundreds of units in as many buildings as you need from a
single location.
R3
Remote test
receiver
Used to perform maintenance tests by means of radio receiver in conjunction
with a remote test transmitter (R4 option) on equipment that are out of reach.
Simply point the transmitter at the unit
R4
Remote test
transmitter
Used to perform maintenance tests by means of radio transmitter along with a
radio receiver (R3 option) on battery units that are out of reach.
TC
Teflon coated lens
A protective teflon coating that is applied to the glass lens of a lighting fixture to
prevent broken shards from falling in the event the glass is accidently broken or
vandalised.
TP
Tamper-proof
screws
Screws that require a special bit. Can be used on certain units to deny access to
unauthorized personnel.
D
®
95
THE
exit
GLOSSARY
In the event of failure of the normal
power supply, self-contained battery
units automatically provide the
illumination required to evacuate
the building safely.
overview
P. 100-101
decocab legend™
P. 108-109
LDXC
P. 118-119
TUF-NM
CADILITE®
P. 102-103
ldx-vq
P. 110-111
LDXA
P. 120-121
LDX-HZ
P. 128-129
P. 130-131
RIB
GLOssary
P.138
n
INVISILITE™
P. 104
ldx-t
mini INVISILITE™
AVENGER™
LDX-TS
ESCAPE™
P.105
P. 112-113
P. 114-115
ULTIMA™
LES18P
P. 122-123
LDX-I
P.32-133
P.124
LDX-NX
P.134-135
n
P. 106
P. 116
B-29
P. 125
SIPR
P. 136
P. 139
n = new product
99
legend™
P. 107
RCSB
P. 117
LDX
P. 126-127
IPR
P.137
n
table
of
contents
BATTERy
units
overview
Life Safety Equipment
cENTRAL SYSTEMS
Emergency Lighting, as part of Life Safety Equipment, is one of the
key elements to ensure public safety within buildings. In the event of
failure of the normal power supply, self-powered units automatically
provide the illumination required to evacuate the building in safe
conditions.
A higher wattage capacity emergency system is a Central System.In
the event of a utility power failure, Central Systems continue to supply
power to the emergency lighting equipment as well as other critical
loads. A Central System that supplies power during a utility power
failure is an emergency power system of which there are two types of
Central Systems: the Direct Current Central System (DC System) and
the Alternating Current Central System (AC inverter, UPS or Uninterruptible Power Supply/System). The electric power supplied by these
systems can vary from a few KVAs to several hundred KVAs.
STANDARDS AND CODES
Requirements for the installation, level, and duration of emergency
lighting in buildings are established by national standards: the
National Building Code of Canada (CNBC-2005), the Canadian
Electrical Code (CEC), and the National Fire Code of Canada
(NFC-2005). Concerning the equipment, performance is established by the Canadian Standards Association (CSA), for example:
C22.2 No.141, C860, etc. Types of Emergency Lighting Emergency
lighting equipment is divided in two main categories: self-powered
emergency lighting equipment, also referred to as “unit equipment for
emergency lighting’’, and central emergency power systems (separate
emergency electrical power supply).
SELF-POWERED (OR SELF-contained) EQUIPMENT
The most common self-powered unit consists of a 6V lead battery
and two lamp heads, also referred to as emergency lights, each with
a 6V, 9W incandescent lamp. Lamps are normally off; the storage
battery has sufficient capacity to actuate and maintain the emergency
lighting for at least 30 minutes in the event of a power failure. In some
applications described in the National Building Code of Canada, the
minimum emergency lighting period can reach 60 minutes or even
120 minutes. This will require battery units of a greater capacity.
Once normal AC power supply is restored, heads turn off (if they were
still on), the fixture recharges the batteries to full capacity within 24
hours, then returns to the stand-by mode.
BATTERY UNITS AND REMOTE HEADS
There are also battery powered units that will supply power to several
remote emergency lights of different wattages (12W, 20W, 50W, etc.).
In this case, remote emergency lights (also referred to as remote
heads) are installed in rooms and corridors, connected by wiring
installed inside the walls. Some 6V self-contained fixtures can assume
a total emergency lighting load up to 150W – 180W. At this level, the
battery current (25A – 30A) begins to generate significant losses in
the external wiring. For this reason, there are battery units of higher
voltages, 12V and 24V, which can respectively supply power to remote
heads totalling up to 360W and 720W.
INDUSTRIAL ENVIRONMENT
The industrial environment is the most severe in terms of housing
construction requirements. It is defined by a number of parameters
specific to various technical processes within the industry: temperature
range, degree of humidity, degree of protection against water and
dust, resistance to corrosive chemicals, presence of flammable
gases and vapors or combustible particles, etc. An important performance factor is the degree of protection against solid particles
(dust, etc.) and liquids. This rating is generally defined and measured
as established by the American standard NEMA 250-2003 from the
National Electrical Manufacturers Association, or, alternately, the
European IP (ingress protection) code of the International Electrotechnical Commission (IEC 60529 standard). To accomplish the required
degree of protection and resistance to corrosive agents, emergency
lighting fixtures are designed/fabricated with gasketed, rugged, polycarbonate or fiberglass housings. A special category exists covering
hazardous areas, defined by technological processes generating (or
susceptible to generate)flammable gases, vapors, flammable liquids
or combustible dust particles in explosive concentrations in the
atmosphere. Hydrogen or acetylene plants, gasoline and natural gas
refineries, coal or magnesium mines, flour mills and textile factories
are some examples. For more details on definitions and classifications of hazardous areas, consult the Canadian Electrical Code
(CSA C22. 1-06).
Considering the risks of explosion or fire, all equipment dedicated to
hazardous areas must meet, special standards such as: CSA C22.2
No. 30-M1986, No. 137-M1981, No. 213-M1987, etc. Based on
each respective classification (Class, Division, Group), enclosures
and remote heads for hazardous areas are fabricated of materials
which must meet stringent requirements (pure forged aluminum,
fiberglass, etc.) and may require specific components, such as seals,
valves, gasketing, etc in addition to standards specific to emergency
lighting. In view of all these additional specific characteristics, it
can be expected that emergency lighting equipment approved for
hazardous areas will cost more than fixtures classified for general
industrial applications.
100
battery
units
overview
EMERGENCY LIGHTING ENCLOSURES
Construction requirements for emergency lighting fixtures depends
on the location where the equipment is to be installed. Of all the
components, the enclosure (box or housing) is probably the most
affected by the type of environment where it is located.
The enclosure plays many roles: it provides the fixture with a degree
of protection against the environmental conditions, while meeting
technical, aesthetic and functional requirements. Of course, cost can
also be a deciding factor when selecting a fixture.
In general, non-residential lighting is divided in three market segments:
commercial, institutional and industrial. This market segmentation still
applies in the case of emergency lighting. Typically, the commercial
and institutional sectors are more sensitive to costs and aesthetics,
whereas the industrial sector is more influenced by the technical
aspects (fixture durability, etc.).
COMMERCIAL AND INSTITUTIONAL ENVIRONMENTS
Commercial spaces (stores, restaurants, theatres, hotels, etc.) as well
as institutions are generally air conditioned, so the equipment operates
in normal temperature and humidity conditions. Generally, the main
selection criteria is total lighting costs, which include equipment and
installation. The most economical design for self-contained units uses
sheet metal housings of a neutral colour: white or whist. For the
most part, exit signs are housed in a rectangular box fabricated of
steel (sheet metal) die-cast or extruded aluminum, and illuminated
from a light source contained within the assembly (back-lit). Some
molded plastic housings also exist (less expensive material, but also
less rigid than metal) – mostly used for small battery units (lower
wattages) and EXIT signs in some applications. Even if aesthetics is
a secondary criteria, we continue to develop products which offer a
more contemporary look.
for remote heads. There are also single-lamp battery units (MR16
or PAR36) that can be recessed in the ceiling. As for remote heads,
they are generally fabricated of forged aluminum and contain halogen
MR16 lamps. It is also possible to conceal the battery units as well
as the lamp heads entirely. For example, both the lamp heads and
the housing of the Invisilite™ self-contained unit are concealed in the
wall or ceiling cavity, behind its door which rotates 180°. Upon power
failure, an electromechanical device opens the door and exposes the
emergency lamp heads to illuminate the path to safety. At the end
of the power failure, this same device retracts the heads and closes
the door.
To address specifiers’ needs for aesthetics, we have developed new
products for high end emergency lighting: dual-function decorative
luminaires providing both normal lighting and emergency lighting.
The lamps are powered by one of the two independent electrical
circuits: AC circuit for normal lighting (including the wall switch),
and an uninterrupted AC circuit for the battery charger and control of
the emergency lighting. Since normal lighting levels are higher than
those required for emergency lighting, we also offer the same type of
luminaire for normal lighting only. This option provides the end user
with the possibility of alternating self-contained units with standard
lighting fixtures, while maintaining consistency of design.
AESTHETICS AND ARCHITECTURE
Fortunately, price isn’t everything in the buying decision process.
Some hotel chains, high-end stores and corporate headquarters are
excellent examples.
In these situations, the architect and the lighting designer have a great
influence in specifying emergency lighting fixtures. The question becomes
– what will the architect prefer, a more decorative or a more unobtrusive, discreet look? Battery units are becoming increasingly discreet.
The specifier can opt for a higher capacity unit (e.g.: 24V, 720W or
a central DC System) installed in a hidden location, to supply power
to remote heads distributed throughout the building. Another option
would be to install recessed self-contained units concealed in the
ceiling (T-bar), each with two lamp heads and additional capacity
101
Type:
new product
Project/Location:
Contractor:
Prepared By:
NEMA-3R
Date:
Made in Canada
Model No.:
Typical specifications
Rugged, Versatile, Sophisticated
Features
• Die-Cast aluminum housing, available
in four finishes: dark bronze, off-white,
black, and platinum grey
• Nema-3R Rated for indoor/outdoor wet
and damp locations: -20°C to 50°C
• Wall-mount installation on various
junction boxes or via rigid conduit
• Patent-pending design for easy
installation: wall-mount
backplate includes electrical wire box
with snap-on connector
• Patent-pending light engine: four power
LEDs with redundant inter-connections
and very wide beam
• Clear polycarbonate lens of reduced
size (3” x 1.5”), shock-absorbent and
UV-resistant
• Battery: high-temperature rated,
Nickel-Metal Hydride technology
• Power consumption in stand-by:
less than 5W
• Self-Test and diagnostic functions
operated by micro-controller
• Certified to CSA 22.2 No.141-10
and No.250.0-08 standards
• 90 minutes run time
Options
• Cold weather: (-40°C)
• Forward-throw light distribution, for
applications of outdoor exit discharge
(OSHA 1910.36)
• High-lumen output: 25 to 50%
additional level of illumination
compared to standard models
• Dual-mode operation: normal lighting
and/or emergency lighting with separate
AC inputs
• Photo-switch: dusk-to-dawn control
of normal lighting
• Remote test: infrared remote control
(keypad ordered separately)
• Time delay: 15 minutes
c a d i l i t e ® fa m i ly
Cadilite® Remote P. 146-147
POwer consumption
model type
AC SPECS: 120/347VAC
6-12VDC remote
normal lighting
emergency lighting
Current (max) Power (max) Current (max) Power (max)
Power (max)
ACSD, SD, SD-H
0.12/0.05 A
12W
0.05/0.02 A
5W
SD-CW
-
-
0.16/0.06 A
16W
0.24/0.10 A
24W
ACSD-CWP, -CW-RC
not required*
NiMH battery
*Note: Only unswitched AC input; normal lighting with photo-switch or remote control
Dimensions
Dimensions are approximate and subject to change.
3” [7.5 cm]
6-5/8” [16.8cm]
3” [7.5 cm]
9-1/2” [24 cm]
Cadilite® Series
Supply and install the Cadilite® Series of LED emergency lighting from Ready-Lite®. The unit body shall include
a back-plate and housing made of Die-Cast aluminum with paint finish colour: _______ and a UV- and
impact-resistant polycarbonate lens of reduced size: 3-in by 1.5-in. The back-plate shall have knockouts for
wires and wall-mount installation box as well as a threaded hole for rigid conduit entry at the top of the unit.
The back-plate shall have a built-in electrical box with wire terminals and snap-on connector. After complete
electrical installation of the back-plate the equipment housing shall be installed by a simple push & snap over
the back-plate. The emergency lights shall be 4 (four) power light-emitting diodes (LED) with operational life of
minimum 36,000 hours, maintaining at least 70% of the initial light level (reported L70). The LED lamps shall
have redundant interconnections: eventual failure of one lamp shall allow other LED lamps to function. The
unit shall have a dual-voltage input rated 120/347VAC, 60Hz. The battery charger shall include low voltage
disconnect to prevent deep discharge, battery lockout to prevent battery drain prior to energizing the utility
power, and brownout protection which will automatically switch the unit into emergency mode if the utility
power falls below 80% of nominal level. The unit with Nickel-Metal Hydride battery shall be equipped with a
micro-controller-based non-audible auto-test circuit and provide minimum 90 minutes of emergency lighting.
The unit shall self-test for one minute every month, 30 minutes every six months and 90 minutes annually.
The pilot light shall be integrated with the test button; it shall be a bi-colour LED and shall change colour from
normal green to flashing red when a failure is detected from the battery, charger circuit or lamps. A label
located near the pilot light shall describe the diagnostic for each flashing code. When specified, models with
dual-mode illumination shall include two separate AC input circuits: un-switched for emergency lighting and
switched for normal lighting. When specified, models equipped with photo-switch shall automatically activate
the normal lighting only from dusk till dawn, for additional energy savings. The typical ambient illumination
for the photo-switch shall be 10 lux (to turn-on) and 30 lux (to turn-off). When specified, the unit shall be
controlled by an infrared remote control keypad (ordered separately). The remote control shall be able to
simulate a power failure of 1 minute, 30 minutes or 90 minutes and also to cancel the test in progress at any
time. For units with dual-mode lighting the remote keypad shall also control the normal lighting with on/off
switch and dimming functions. The unit shall be certified to CSA 22.2 No.141-10 for minimum 90 minutes
and No.250.0-08 standards.
The unit shall be Ready-Lite® model:
.
102
Window for
photo-switch
(optional)
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Table a: spacing for average 1fc/national building code, canada
Model Type
Mounting Height
wattage capacity
CENTRE-TO-CENTRE
SINGLE
standard
9’
6’ X 50’
with option -H
11’
6’ X 60’
with option -FT
12’
6’ X 40’
6’ X 50’
6’ X 60’
3’ X 70’
-
with option -FTH
15’
6’ X 50’
-
cadilite® Series
Indoor reflectance: 80/50/20 and 10-ft wide corridor.
Outdoor reflectance: 0/30/10
Note: The illumination level meets ALL the requirements of the National Building Code-Canada and the Life
Safety Code (NFPA 101):
1) Average of 1 foot-candle or more
2) Minimum at any point of 0.1 foot-candle or more
3) Maximum-to-minimum illumination uniformity ratio of 40:1 or less
Rugged, Versatile, Sophisticated
Table B: spacing for minimum 1fc max./min.
uniformity ratio less than 3:1
Model Type
Mounting Height
standard
with option -H
with option -FT
with option -FTH
9’
11’
12’
15’
SINGLE
wattage capacity
CENTRE-TO-CENTRE
4’ X 28’
4’ X 32’
4’ X 22’
4’ X 27’
table A
4’ X 32’
4’ X 40’
-
table B
Forward Throw (Optional)
Wide Beam (Standard)
12’
1FC
1FC average
50’
minim
28’
1FC
um
9’
6’
e
erag
av
1FC
um
minim
22’
40’
6’
Remote control keypad
Patent Pending
Emergency Lighting
Normal lighting with
switch & dimming
Part#: TB-RC1-R
ordering information
series
CAD= cadilite® LED
Function: Battery units
SD= self-powered & diagnostic
(-20°C to 50°C)
ACSD= dual-mode AC/self-powered &
diagnostic (-20°C to 40°C)
colour
BK= black
DB= dark bronze
OW= off white
PG= platinum grey
Options
­U2= 277VAC 60Hz input
­CW= cold weather (-40°C; not available with option -H)
­D3= time delay (15 mins.)
­FT= forward throw lighting
­H= high lumen output (max. 30°C; model SD only)
­P= photo-switch (model ACSD only)
­RC= remote control - infrared*
*TB-RC1-R= remote control keypad (sold separately)
Example: CADSDBK-CW
103
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Invisilite™ Series
100% Recessed
Emergency Lighting
Features
• Door flips 180° when AC fails
• Fully automatic operation – brown-out
sensitive transfer circuit automatically
goes to emergency lighting mode and,
when the power is restored or at the end
of battery discharge, the motor turns the
door back to its original closed mode
• Customized finish – Off-white, but can be
painted or wallpapered on site to match
existing decor
• Heavy-duty back-box – made of heavy-duty,
galvanized steel
• High-performance lighting– includes two
MR16 halogen lamps; power range from
12W to 50W, LED up to 4W, 5W & 6W
• Patent-pending design
• Meets or exceeds CSA 22.2 No.141
Supply and install Ready-Lite® Invisilite™ Series. The unit shall be designed to be concealed in walls or
ceilings with a cavity, including T-bar suspended ceilings. Bar hanger brackets shall be provided with the
Self-Powered unit. The unit equipment shall come standard with a metal back box containing the batteries,
the lamp assembly and a charging circuitry. The back box shall be constructed of heavy-duty galvanized steel.
The unit components: battery assembly, charger circuitry and lamp assembly shall have a modular design
and come standard with quick-connect plugs for easy installation in the back box. The unit equipment shall
be completely concealed in the wall or ceiling during normal power conditions. Upon a power failure the unit
will expose the emergency heads by rotating its door 180° and then power the lamps. At the restoration of
the AC power or at the end of the battery discharge, the lamps will turn off and the unit will retract the heads
in the wall (ceiling) by rotating the door by 180°. Under normal conditions, the only visible parts of the unit
shall be the flat door and trim plate, coated with a high-quality off-white finish that can be customized on site
with paint or other suitable wall covering. The light source shall be 12V MR16 halogen lamps of specified
wattage and light output.
The unit shall supply the rated load for a minimum of 30 minutes or until the battery is discharged to 87 ½%
of its nominal voltage (whichever duration is longer). The charger circuitry shall utilize a micro-controller IC that
samples the battery in relation to the ambient temperature, state of charge, and input voltage fluctuations. The
charger shall be current limited, temperature compensated, short-circuit proof, and reverse-polarity protected.
The circuit will charge in accordance with CSA C22.2 – 141 requirements. The unit shall be furnished with a
recessed, illuminated push button serving as test switch and status indicator light. When specified, the unit
shall come complete with Ready-Lite® auto-test micro-controller circuitry to ensure the equipment readiness
and reliability by continuously monitoring every critical function of the unit. If a problem occurs, the pilot light
located on the front of the unit will change colour from green to red and will flash indicating a fault. A detailed
diagnostic legend shall be available on the door back side and shall provide fault identification (battery, charger
circuitry, lamps) for maintenance personnel.The auto-test shall simulate a power loss for one minute monthly,
10 minutes every 6 months, and a full 30-minute test every 12 months.
The equipment shall be Ready-Lite® model:
.
Power consumption
Model
ac aspecs
HIDE75
120/347VAC
HIDE150
30min
0.25/0.09 A
dimensions
Dimensions are approximate and subject to change.
7” [17.8 cm]
23-7/8” [60.6 cm]
3-3/8” [8.6 cm]
9-1/8” [23.2 cm]
7-7/8” [20.0 cm]
wattage capacity
1h00
1h30
2h00
4h00
75
40
30
24
15
150
80
60
48
30
replacement lamps: MR16 type
model
LAMP Type
voltage/
wattage
580.0080-RL
MR16 halogen
12V-12W
580.0064-RL
MR16 halogen
12V-20W
580.0083-RL
MR16 halogen
12V-35W
580.0076-RL
MR16 halogen
12V-50W
580.0068-RL
MR16 high-lumen output
12V-20W H
580.0090-RL
MR16 high-lumen output
12V-35W H
580.0089-RL
MR16 high-lumen output
12V-50W H
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
ordering information
series
HIDE
unit capacity
75= 12V-75W
lead-acid
150= 12V-150W
lead-acid
lamp wattage (12V)
LD7= MR16 LED, 2X 4W
LD9= MR16 LED, 2X 5W
LD10= MR16 LED, 2X 6W
12W= MR16 halogen, 2X 12W
20W= MR16 halogen, 2X 20W MR16
35W= MR16 halogen, 2X 35W MR16
50W= MR16 halogen, 2X 50W MR16
20WH= MR16, 2X 20W high lumen output lamp
35WH= MR16, 2X 35W MR16, high lumen output lamp
50WH= MR16, 2X 50W MR16,high lumen output lamp
E XAMPL E : H I D E 7 5 1 2 W A D
104
options
AD= auto-diagnostics*
ADN= auto-diagnostics, non-audible*
D3= time delay (15 mins.)
*Minimum lamp load required: 20% of unit
capacity
AC voltage
Blank= 120/347VAC
U277= 120/277VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install Ready-Lite® Mini Invislite™ Series. The unit shall be designed to be completely concealed in
walls with a cavity. The equipment shall consist of a metal housing containing two modules joined by a flexible
bracket and electric conduit. One module contains the battery, charger circuitry and electrical connection box;
the other module contains the emergency lights installed on the back of a door able to rotate several turns of
360°. The unit equipment shall be completely concealed in the wall after installation through a rectangular
opening not larger than 8.25” by 5.75”. In stand-by mode, the only visible parts of the unit shall be the flat
door and trim plate, coated with a high-quality off-white finish that can be customized on site with paint or
other suitable wall covering. Upon a power failure the unit will expose the emergency heads by rotating its door
180° and then will power the lamps. At the restoration of the AC power or at the end of the battery discharge,
the lamps will turn off and the unit will retract the heads by rotating the door 180° in the same direction. The
unit shall not require the presence of AC power in order to close the door and conceal the lights. The door of
the unit shall be easy to force-turn (open or close) by hand, in any rotation direction. The light source shall
be 12V MR16 lamps of specified technology, wattage and light output. The unit shall supply the rated load
for a minimum of 30 minutes or until the battery is discharged to 87.5% of its nominal voltage (whichever
duration is longer). The charger circuitry shall utilize a micro-controller IC that samples the battery in relation
to the ambient temperature, state of charge, and input voltage fluctuations. The charger shall be current
limited, temperature compensated, short-circuit proof, and reverse-polarity protected. The circuit will charge
in accordance with CSA C22.2 – 141 requirements. The unit shall be furnished with a recessed, illuminated
push button serving as test switch and status indicator light. When specified, the unit shall come complete with
the Ready-Lite® series of auto-test micro-controller circuitry to ensure the equipment readiness and reliability
by continuously monitoring every critical function of the unit. If a component failure occurs, the pilot light
located on the front of the unit will change colour from green to red and will flash indicating a fault. A detailed
diagnostic legend shall be available on the back side of the door and shall provide fault identification (battery,
charger circuitry, lamps) for maintenance personnel. The auto-test shall simulate a power loss for one minute
monthly, 10 minutes every 6 months, and a full 30-minute test every 12 months.
The equipment shall be Ready-Lite® model:
.
Dimensions
Dimensions are approximate and subject to change.
9-1/8” [23.2 cm]
Installed Unit
17-5/8” [44.8 cm]
5-1/4” [13.2 cm]
7” [17.8 cm]
Complete Unit
mini invislite™
Series
Unseen Solution,
The Next Generation
Features
• Easy to retrofit in finished walls: the unit
slides in through an 8.25” by 5.75” hole
• No back-box needed to pre-install
• Input: Standard AC input 120/347VAC;
optional 120/277VAC
• Output: 12VDC with up to 100W of
power
• Battery: choice of sealed, maintenancefree Lead-Calcium or Nickel-Metal
Hydride
• Remote capacity: can drive several wall
or ceiling-mount 12VDC remote
Invisilite™ fixtures
• Charger: micro-controller driven,
temperature compensated, high
precision, fast recharge
• Remote AC fixture: direct connection
to 120 or 347VAC power generators
• MR16 halogen lamps; power range
from 12W to 50W, LED; 4W, 5W and 6W
• Certification: CSA C22.2 No.141
3-1/2” [8.9 cm]
replacement lamps: MR16 type
Power Consumption and unit rating
model
lamp type
voltage/wattage
580.0080-RL
580.0064-RL
MR16 halogen
MR16 halogen
12V-12W
12V-20W
580.0083-RL
580.0076-RL
580.0068-RL
MR16 halogen
MR16 halogen
MR16 high-lumen output
12V-35W
12V-50W
12V-20W
580.0090-RL
MR16 high-lumen output
12V-35W
580.0089-RL
MR16 high-lumen output
12V-50W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
model
wattage capacity
30min 1h00 2h00 3h00
ac specs
MHL80
120/347VAC
-
80
40
24
-
MH100
120/347VAC
0.25/0.08 A
100
70
36
24
MHG1
120VAC
max. 0.95 A
maximum 100W load
MHG2
277VAC
max. 0.45 A
maximum 100W load
MHG3
347VAC
max. 0.35 A
maximum 100W load
ORDERING INFORMATION
series
MH
unit capacity
L80= lead-calcium,
12V-80W
H100= n
ickel-metal hydride,
12V-100W
lamp wattage (12V)
LD7= MR16 LED, 2X 4W
LD9= MR16 LED, 2X 5W
LD10= MR16 LED, 2X 6W
12W= MR16 halogen, 2X 12W
20W= MR16 halogen, 2X 20W
35W= MR16 halogen, 2X 35W
50W= MR16 halogen, 2X 50W
20WH= 2X 20W MR16, high lumen output lamp
35WH= 2X 35W MR16, high lumen output lamp
50WH= 2X 50W MR16, high lumen output lamp
options
AD= auto-diagnostics*
ADN= auto-diagnostics,
non-audible*
D3= time delay (15 mins.)
TB= T-Bar mounting kit
*Minimum lamp load required:
20% of unit capacity
E XAMPL E : M H L 8 0 1 2 W A D
105
AC voltage
Blank= 120/347VAC
U2= 120/277VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
avenger™ Series
The contractor will install the Ready-Lite® Avenger™ Series battery unit. The emergency lighting system shall
consist of fully automatic equipment with two (2) emergency lighting heads. The emergency lighting heads
shall require no tools for adjusting or aiming. Each unit shall contain a fully automatic, solid-state charger with
test switch and AC-on pilot lights.
The unit shall contain a sealed transfer circuit and low-voltage disconnect circuit. The unit equipped with
self-testing auto-diagnostic or Nexus® features shall automatically self-test for one minute every 30 days, 10
minutes in the 6th month and 30 minutes annually. When a fault is detected, the bi-colour pilot light shall turn
from green to red and shall flash, identifying the source of the failure: battery, charger circuitry, lamp load.
The battery shall be 6V with a capacity of 20W or 36W for 30 minutes.
The unit shall meet CSA C22.2 no 141.
The unit shall be Ready-Lite® model:
• Injection-molded, impact, scratch and
corrosion-resistant thermoplastic with a
snap-together design
• Compact and versatile – unit measures
only 11.75” x 5” and can be wall or
ceiling mounted
• Variety of lamp types including optional
MR16 LED lamps with life expectancy
of 50,000+ hours
• Maintenance-free, long-life sealed Lead
Calcium battery
• Fast and easy installation - AC quick
connect plug, battery knockout feature
• Fully automatic, solid-state charger with
low voltage battery disconnect, brownout
protection, integral test switch and
long-life LED AC-On pilot lights
• Charger is temperature compensated
and reverse polarity protected
• NEXUS® compatible (For more
information, please consult your
sales representative)
• Optional ceiling mount includes safety
wire and pre-machined housing to
receive a securement screw
• Meets or exceeds CSA 22.2 No.141
Wire guards
460.0080-RL
wall mount
replacement lamps
model
lamp type
voltage/wattage
570.0012-RL
mini tungsten, wedge base
6V–5.4W
580.0079-RL
MR16, flood
6V–10W
580.0097-RL
MR16, LED
6V–4W
Dimensions
Dimensions are approximate and subject to change.
5-7/8” [14,9 cm]
11-3/4” [29.9 cm]
5” [12,7 cm]
Features
.
POwer consumption and unit rating
model
AVNG20N
AVNG36N
ac specs
120/347VAC
wattage capacity
30min
1h00
1h30
2h00
0.07/0.03 A
20
15
12
8
4h00
-
0.08/0.03 A
36
21
15
12
6
ordering information
Series
AVNG20N= 6V, 20W
AVNG36N= 6V, 36W
Unit Type
Blank= standard
-AD= auto-diagnostics
-ADNA= auto-diagnostics,
non-audible
-NEX= NEXUS® system interface*
-NEXRF= wireless NEXUS® system
interface*
input voltage
Blank= 120/347VAC
2= 120/277VAC
Lamp Type
Colour
LD1= MR16 LED, 6V-4W
M10= MR16 halogen,
6V-10W
65= mini tungsten, 6V-5.4W
Blank= factory white
B= black
options
Blank= no options
C= line cord (120VAC only) not installed
CM= ceiling mount
VM= voltmeter*
VR= vandal resistant screws**
*Available with AVNG-20N only
*Not all options available with NEXUS®
System. Please consult your sales
representative
*Available with standard unit only
**690.0454 bit sold separately
E x a m p l e : AV N G 2 0 - N E X R F L D 1 V R
106
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
Recessed heads and housings: The contractor will supply and install Ready-Lite® Legend™ Series internally
Self-Powered series. The unit will have a dual input 120/347VAC 60Hz. Recessed heads will be constructed
of a durable powder coated, or electro plated Die-Cast aluminum construction and use MR16 halogen light
sources and a 5 year Nickel-Cadmium battery.
The recessed head will be adjustable to 0-90° vertical and 0-350° horizontal angle. The light source will be
6V-6W, MR16 halogen narrow beam or otherwise specified. The unit shall be equipped with a sealed, hightemperature Nickel-Cadmium battery which will supply the emergency lamp for minimum 30 minutes of
illumination in case of power failure.
The equipment shall be Ready-Lite® Model:
.
replacement lamps
ordering code
lamp type
voltage/wattage
580.0074-RL
MR16
6V-6W
580.0079-RL
MR16
6V-10W
• Durable, powder-coated or electroplated
Die-Cast aluminum construction
• High-performance MR16 halogen light
source
• Maintenance-free, sealed Nickel
Cadmium battery
• Quick disconnect feature for easy trim
installation; easy to access for
maintenance
• Fully automatic, solid-state PulseGuard charger with low voltage battery
disconnect, brownout protection,
integral test switch and long-life LED
AC-On pilot lights
• Charger is designed for
Nickel-Cadmium continuous trickle
charge and is reverse polarity protected
• Recessed, directional, retractable trim
• Meets or exceeds CSA 22.2 No.141
Dimensions are approximate and subject to change.
Closed position
5” [12.7 cm]
7” [17.8 cm]
7-5/8” [19.4 cm]
Decorative Recessed Fixture
Features
Dimensions
Open position
legend™ Series
o-90°
5” [12.7 cm]
19” [48.3 cm]
POwer consumption and unit rating
model
RLR2
emergency power for lamps
ac specs
120/347VAC
0.08/0.03 A
30min
1h00
1h30
2h00
4h00
10
-
6
-
-
ordering information
Series
RLR2
colour
WH= white
BK= black
BN= brushed nickel
CH= chrome
PB= polished brass
standard
SP-C= self-powered
E XAMPL E : R L R 2 W H S P - C
107
lamp wattage
Blank= MR16 halogen, 6V-6W
10= MR16 halogen, 6V-10W
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
legend™
decocab Series
Decorative 6, 12 and 24V
High performance and
energy efficiency in a
contemporary design.
The Legend ™ DecoCab Series decorative
battery units combine a contemporary
design with the latest in high-tech security
capability.
Designed to meet the needs of interior
design professionals, these battery units
are also high performance and
energy-efficient.
Supply and install the Ready-Lite® Legend™ DecoCab Series battery units.
The battery unit will supply the rated load for a minimum of
hour to 87.5% of the rated battery/voltage.
The unit shall be rated 120 or 347V, 60 Hz and be CSA No.141 listed. The charger shall be fully computer
tested and its charge voltage factory set to + or – 1% tolerance. A pulse type charger shall be employed to
promote long battery life and reduce the potential for grid corrosion. The charger shall provide continuous
high charge to recharge the battery. When the battery is at full capacity the charger will shut off. The pulse
charge shall be current limited and precisely regulated by an electronic circuit which samples the battery in
relation to its temperature, state of charge and input voltage fluctuations. The charger shall be current limited,
temperature compensated, short-circuit proof and reverse polarity protected.
The unit shall be furnished with an electronic lockout circuit, which will connect the battery when the AC
circuit is activated, and an electronic brownout circuit, which will activate the emergency lights when utility
power dips below 75% of nominal voltage.
A low voltage battery protection circuit will disconnect the battery at end of the discharge. The unit will come
complete with the Legend™ DecoCab Series Series diagnostics micro-controller board option. The unit shall
self-test for 1 minute every 30 days, 10 minutes on the 6th month and 30 minutes every 12 months. The unit
shall be furnished with a sealed dust tight relay, a selectable test switch 1 minute, 5 minutes, 10 minutes or
20 minutes and diagnostics LED indicator lights to continuously monitor the status of the unit: battery failed,
battery disconnect, charger failure, lamp failure, service alarm, AC “ON” and charger “ON”.
The unit shall be Ready-Lite® model:
.
dimensions
Dimensions are approximate and subject to change.
Features
• Rugged steel cabinet with
corrosion-resistant undercoating
• Removable front panel on cabinet
provides easy access and allows unit
to be mounted at ceiling height
• Solid-state pulse-type charger – currentlimited, temperature-compensated
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator lights
continuously monitor unit status
• Long-life, maintenance-free lead
acid battery
• NEXUS® compatible (for more
information on NEXUS®, please
consult your sales representative)
• CSA C22.2 No. 141 certified
d
c
b
a
dimensions
cabinet
a
b
c
d
A
13-1/4” (33.7 cm)
3-5/8” (9.2 cm)
10-1/2” (26.7 cm)
14-1/4” (36.2 cm)
B
16-1/8” (40.9 cm)
5-1/2” (13.9 cm)
10-1/4” (26.0 cm)
13-7/8” (35.2 cm)
C
23-1/8” (58.7 cm)
5-1/2” (13.9 cm)
10-1/4” (26.0 cm)
13-7/8” (35.2 cm)
Wire guards
460.0078-RL
wall mount
“A” cabinet
460.0081-RL
wall mount
“B” cabinet
460.0034-RL
wall mount
“C” cabinet
REPLACEMENT LAMPS
ordering code
lamp type
570.0074-RL
MR16, halogen
voltage/ wattage
6V-6W
570.0079-RL
MR16, halogen
6V-10W
12V-12W
570.0080-RL
MR16, halogen
570.0097-RL
MR16, LED
6V-4W
570.0093-RL
MR16, LED
12V-4W
570.0104-RL
MR16, LED
12V-5W
570.0106-RL
MR16, LED
12V-6W
570.0098-RL
MR16, LED
24V-4W
For the complete list, please see the lamp chart on pages 166 to 168
108
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Distinction™ Series
Model No.:
POwer consumption and unit ratingDecorative 6, 12 and 24V
model
ac specs
wattage capacity
30min
1h00
1h30
2h00
LDX636
0.10/0.04 A
36
21
15
12
4h00
6
LDX672
0.22/0.08 A
72
42
30
24
12
LDX6108
0.22/0.08 A
108
63
45
36
18
LDX6180
0.22/0.08 A
180
105
75
60
30
LDX1272
0.15/0.06 A
72
42
30
24
12
LDX12100
0.34/0.12 A
100
58
42
33
17
LDX12144
0.40/0.14 A
144
84
60
48
24
LDX12216
LDX12250
120/347VAC
0.41/0.14 A
216
120
90
72
36
0.41/0.14 A
250
144
100
83
42
LDX12360
0.43/0.15 A
360
300
210
170
80
LDX24144
0.55 / 0.20 A
144
84
60
48
24
LDX24200
0.67 / 0.23 A
200
117
83
67
33
LDX24288
0.67 / 0.23 A
288
168
120
96
48
LDX24350
0.67 / 0.23 A
350
200
144
120
60
LDX24432
0.67 / 0.23 A
432
250
180
144
72
LDX24550
0.88 / 0.33 A
550
320
230
180
90
LDX24720
0.88 / 0.33 A
700
420
300
240
120
LEGEND™
DECOCAB Series
Decorative, 6, 12 and 24V
ordering information
Series
LDX6= 6V
LDX12= 12V
LDX24= 24V
capacity &
cabinet size*
special options
-36= 36W (A)
Blank= standard
-72= 72W (A)
AD= auto-diagnostic,
-108= 108W (A)
audible*
-180= 180W (B) ADN= auto-diagnostic,
non-audible*
-72= 72W (A)
NEX= NEXUS® system
-100= 100W (A)
interface (for 6V and
-144= 144W (A)
12V units only)*
-216= 216W (B) NEXRF= wireless NEXUS®
-250= 250W (B)
system interface*
-360= 360W (B)
# of heads head style
lamp voltage-wattage
colour
AC voltage
options
1= one head RL150= closed
2= two
heads
3= three
heads
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
LD13= MR16 LED, 24V-4W
6= MR16 halogen, 6V-6W
10= MR16 halogen,
6V-10W
12= MR16 halogen,
12V, 24V-12W
20= MR16 halogen,
12V, 24V-20W
35= MR16 halogen,
12V, 24V-35W
50= MR16 halogen,
12V, 24V-50W
H20= MR16-IR,
12V-20W high output
Blank= polar
white
BK= black
Blank=
120/347VAC
input
U277= 277VAC
input
A= ammeter
CT= cab-tire
D3= time delay
(15 mins.)
D6= 6
cct. fuse panel
IT= AC terminal block
ITOT= AC/DC terminal
block
LB= light activated test
switch*
LD= lamp disconnect
OT= D
C terminal block
R3= r emote test
receiver**
TL= twist-lock plug
(120V)***
V= voltmeter
-144= 144W (A)
-200= 200W (B)
-288= 288W (B)
-350= 350W (C)
-432= 432W (C)
-550= 550W (C)
-720= 720W (C)
*Minimum lamp load
required: 20% of unit
capacity
*Cabinet size
in not part of
nomenclature
*Available cabinet A only
**R4= remote test
transmitter
(sold separately)
*Not all options available
with NEXUS® System.
Please consult your sales
representative
***120V is standard
E XAMPL E : L D X 6 - 3 6 1 R L 1 5 0 6 , L D X 1 2 - 7 2 1 R L 1 5 0 1 2 , L D X 2 4 - 1 4 4 1 R L 1 5 0 2 0
109
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
typical specifications
Features
• Impact-resistant steel center cabinet
contains the battery and charger
• Frosted, thermoplastic light cubes
protect light modules against vandalism
while providing visual masking and light
diffusion
• Units can be wall or ceiling mounted
• Maintenance-free, sealed Lead-Calcium
battery
• Fully automatic, solid-state charger with
low voltage battery disconnect,
brownout protection, integral test switch
and LED AC-On pilot lights
• Also available as a remote fixture; see
the Remote Fixtures section of this
catalogue
• CSA C22.2 No. 141 certified
• NEXUS® compatible
Wire guards
460.0097-RL
wall mount or ceiling mount
REPLACEMENT LAMPS
ordering code
type
570.0016-RL
mini tungsten
voltage/ wattage
6V-9W
570.0025-RL
mini tungsten
12V-9W
570.0045-RL
mini tungsten
24V-9W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
580.0095-RL
MR16, LED
120V-4W
For the complete list, please see the lamp chart on pages 166 to 168
Dimensions
Dimensions are approximate and subject to change.
30-3/4” [78.1 cm]
4-3/4” [12.1 cm]
21-7/8” [55.6 cm]
110
4-3/4” [12.1 cm]
Decorative 6, 12 and 24V
Thermoplastic Cube Units
4-1/2” [11.4 cm]
LDX-VQ Series
Supply and install a complete emergency lighting system as described herein and shown on the drawings.
The Ready-Lite® LDX-VQ Smart Diagnostic micro-controller board shall supply the rated load for a minimum
of 1/2 hour to 87.5% of the rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and be CSA
listed.The unit shall have an output of
V.
The charger shall be fully computer tested and its charge voltage factory set to ± 1% tolerance. Chargers with
field-adjusted potentiometers are not acceptable. A pulse-type charger shall be employed to promote long
battery life and reduce the potential for grid corrosion. The charger shall provide a continuous high charge to
recharge the battery, and when the battery is at full capacity, the charger will shut off. Periodically the charger
shall provide a pulse of energy to keep the battery topped off. The charger shall be current limited, temperature
compensated, short-circuit proof and reverse polarity protected. The unit shall be furnished with an electronic
lockout circuit, which will connect the battery when the AC circuit is activated, and an electronic brownout
circuit, which will activate the emergency heads when utility power dips below 75% of nominal voltage. A
low voltage battery protection circuit shall be provided and will disconnect the battery from the fused output
circuit at the end of discharge.
The unit shall self-test for 1 minute every 30 days, 10 minutes every 6 months and 30 minutes every 12
months. The unit shall be capable of full recharge in compliance with CSA specifications. The unit shall be
furnished with a sealed, dust-tight relay, a test switch and diagnostic LED indicator lights to continuously
monitor the status of the unit: Battery Failure, Battery Disconnected, Charger Failure, Lamp Failure, Service
Alarm, AC -“ON”, Charger High Rate. The unit shall come complete with fully adjustable 12V or 24V/12W or
20W quartz halogen lamps. Each lamp shall be housed in an impact-resistant polycarbonate cube. The cube
lens shall be frosted to diffuse light.
The unit shall be Ready-Lite® model:
.
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
POwer consumption and unit rating
model
ac specs
wattage capacity
30min
1h00
1h30
2h00
LDX636
0.10/0.04 A
36
21
15
12
4h00
6
LDX672
0.22/0.08 A
72
42
30
24
12
LDX6144
0.22/0.08 A
144
84
60
48
24
LDX6180
0.22/0.08 A
180
105
75
60
30
LDX1236
LDX1272
120/347VAC
0.10/0.04 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
LDX12144
0.41/0.14 A
144
84
60
48
24
LDX12200
0.41/0.14 A
200
117
83
67
33
LDX12288
0.41/0.14 A
288
168
120
96
48
LDX24144
0.55/0.20 A
144
84
60
48
24
LDX24288
0.67/0.23 A
288
168
120
96
48
LDX-VQ Series
Decorative 6, 12 and 24V
Thermoplastic Cube Units
ordering information
Series
capacity
LDX6
-36VQ= 36W
-72VQ= 72W
-144VQ= 144W
-180VQ= 180W
LDX12
-36VQ= 36W
-72VQ= 72W
-144VQ= 144W
-200VQ= 200W
-288VQ= 288W
LDX24
-144VQ= 144W
-288VQ= 288W
special options
# of lamps
lamp style/wattage
AC voltage
Blank= standard
AD= auto-diagnostic*
ADN= auto-diagnostic,
non-audible*
NEX= NEXUS® system
interface*
NEXRF= wireless NEXUS®
system interface*
Blank= two
lamps
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
LD13= MR16 LED, 24V-4W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen,
6V-10W
RM12= MR16 halogen,
12V, 24V-12W
RM20= MR16 halogen,
12V, 24V-20W
RM35= MR16 halogen,
12V, 24V-35W
RM50= MR16 halogen,
12V, 24V-50W
RMH20= MR16-IR,
12V-20W high output
9= m
ini tungsten, 6V, 12V,
24V-9W, wedge base
18= mini tungsten, 12V,
24V-18W, wedge base
8= mini halogen, 6V,
12V-8W, bi-pin
12= mini halogen, 6V,
12V-12W, bi-pin
20= mini halogen, 6V, 12V,
24V-20W, bi-pin
Blank= 120/347VAC input
U277= 277VAC input
options
D3= time delay (15 mins.)
IT= AC terminal block
ITOT= AC/DC terminal block
LC= line cord (120V)
LD= lamp disconnect
OT= DC terminal block
R3= remote test receiver*
TL= twist-lock plug (120V)**
TP= tamper-proof screws***
*Minimum lamp load required:
20% of unit capacity
*R4= r emote test transmitter
(sold separately)
*Not all options available with
NEXUS System. Please consult
your sales representative
**120V is standard
***990.0119-RL= tamper-proof bit
(sold separately)
e x a m p l e : L D X 6 - 3 6 V Q R M 6 , L D X 1 2 - 7 2 V Q 1 2 , L D X 2 4 - 1 4 4 V Q 2 0
111
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
LDX-T Series
6, 12, 24V T-Bar Unit
Fully recessed units
for T-Bar mounting in
suspended ceilings.
The LDX-T Series battery units are designed
for T-bar ceiling grid installation. This
slim-line, unobtrusive unit is ideally suited
for any commercial location where there is
limited wall space and where the greater
directional flexibility of ceiling-mounted
heads is needed to provide greater light
distribution.
Features
• Rugged steel cabinet with
corrosion-resistant undercoating.
• Battery and charger are concealed
above the ceiling level in the unit
cabinet
• Removable panel provides easy access
to battery and circuitry
• Test switch and LED indicators are
mounted on the visible bottom panel
• Units mount quickly and easily in
standard 2’ x 2’ or 2’ x 4’ grids without
any additional hardware
• Solid-state pulse-type charger
– current-limited, temperaturecompensated, short-circuit proof and
reverse-polarity protected
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator lights
• Long-life, maintenance-free lead
acid battery
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• CSA C22.2 No. 141 certified
Supply and install a complete emergency lighting system as described herein and shown on the drawings.
The Ready-Lite® Smart Diagnostic Micro controller board shall supply the rated load for a minimum of a 30
minutes to 87.5% of the rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and be CSA listed.
The unit shall have an output of
V.
The charger shall be fully computer tested and its charge voltage factory set to ± 1% tolerance. Chargers with
field-adjusted potentiometers are not acceptable. A pulse-type charger shall be employed to promote long
battery life and reduce the potential for grid corrosion. The charger shall provide a continuous high charge to
recharge the battery and when the battery is at full capacity, the charger will shut off. Periodically the charger
shall provide a pulse of energy to keep the battery topped off. The charger shall be current limited, temperature
compensated, short-circuit proof and reverse polarity protected. The unit shall be furnished with an electronic
lockout circuit, which will connect the battery when the AC circuit is activated, and an electronic brownout
circuit, which will activate the emergency lights when utility power dips below 75% of nominal voltage. A low
voltage battery protection circuit shall be provided and will disconnect the battery from the fused output circuit
at the end of discharge.
The unit shall self-test for 1 minute every 30 days, 10 minutes every 6 months and 30 minutes every 12 months.
The unit shall be capable of full recharge in compliance with a CSA specifications. The unit shall be furnished
with a sealed dust tight relay, a test switch and seven diagnostic LED indicator lights to continuously monitor
the status of the unit: Battery Failure, Battery Disconnected, Charger Failure, Lamp Failure, Service Alarm,
AC “ON”, Charger High Rate. The unit shall be T-bar mounted and come complete with tool-less emergency
lighting heads requiring no tools to adjust or aim.
The unit shall be Ready-Lite® model:
.
replacement lamps
ordering code
lamp type
voltage/wattage
570.0016-RL
mini tungsten
6V-9W
570.0025-RL
mini tungsten
12V-9W
570.0045-RL
mini tungsten
24V-9W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
For the complete list, please see the lamp chart on pages 166 to 168
dimensions
Dimensions are approximate and subject to change.
e
a
b
d
f
c
cabinet
dimensions
a
b
c
d
e
f
Large Cabinet
23-3/4”
(60.3 cm)
7-1/4”
(18.4 cm)
7-1/8”
(18.1 cm)
10-5/8”
(27.0 cm)
5-5/8” (14.3cm)
13” (33.0 cm)
Small Cabinet
23-3/4”
(60.3 cm)
7-1/4”
(18.4 cm)
4-5/8”
(11.7 cm)
10-5/8”
(27.0 cm)
3-1/4” (8.3 cm)
13” (33.0 cm)
112
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
POwer consumption and unit rating
model
ac specs
wattage capacity
30min
1h00
1h30
2h00
LDX636
0.10/0.04 A
36
21
15
12
4h00
6
LDX672
0.22/0.08 A
72
42
30
24
12
LDX108
0.22/0.08 A
108
63
45
36
18
LDX180
0.22/0.08 A
180
105
75
60
30
LDX1236
LDX1272
120/347VAC
LDX12100
0.09/0.03 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
0.34/0.12 A
100
58
42
33
17
LDX12144
0.40/0.14 A
144
84
60
48
24
LDX12216
0.41/0.14 A
216
120
90
72
36
LDX24144
0.55/0.20 A
144
84
60
48
24
LDX24288
0.67/0.23 A
288
168
120
96
48
LDX-T Series
6, 12, 24V T-Bar Unit
ordering information
Series
LDX6= 6V
capacity
special options
# of heads
-36T= 36W
-72T= 72W
-108T= 108W
-180T= 180W
Blank= standard
AD= auto-diagnostic*
ADN= auto-diagnostic,
non-audible*
NEX= NEXUS® system
interface*
NEXRF= wireless
NEXUS® system
interface*
Blank= no
heads
1= one head
2= two
heads
3= three
heads
LDX12= 12V -36T= 36W
-72T= 72W
-100T= 100W
-144T= 144W
-216T= 216W
LDX24= 24V -144T= 144W
-288T= 288W
HEAD STYLE LAMP WATTAGE
colour
AC voltage
Blank=
Blank=
LD1= MR16 LED, 6V-4W
factory white 120/347VAC
LD7= MR16 LED, 12V-4W
BK= black
input
LD9= MR16 LED, 12V-5W
U277= 2
77VAC
LD10= MR16 LED, 12V-6W
input
LD13= MR16 LED, 24V-4W
150LD1= deco head, MR16 LED, 6V-4W*
150LD7= deco head, MR16 LED, 12V-4W*
150LD9= deco head, MR16 LED, 12V-5W*
150LD10= deco head, MR16 LED, 12V-6W*
150LD13= deco head, MR16 LED, 24V-4W*
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V, 24V-12W
RM20= MR16 halogen, 12V, 24V-20W
RMH20= MR16-IR, 12V-20W, high-output
150MA= deco head, MR16 halogen, 12V-20W*
150MB= deco head, MR16 halogen, 12V-35W*
150MC= deco head, MR16 halogen, 12V-50W*
150MS= deco head, MR16 halogen, 24V-12W*
150MD= deco head, MR16 halogen, 24V-20W*
150ME= deco head, MR16 halogen, 24V-35W*
150MF= deco head, MR16 halogen, 24V-50W*
LT9= large tungsten, 6V, 12V, 24V-9W, wedge
base
LT18= large tungsten, 12V, 24V-18W, wedge base
LT25= large tungsten, 6V, 12V, 24V-25W, DCB
RT9= m
ini tungsten, 6V, 12V, 24V-9W, wedge
base
RT18= mini tungsten, 12V, 24V-18W, wedge base
RQ8= mini halogen, 6V, 12V-8W, bi-pin
RQ12= mini halogen, 6V, 12V, 24V-12W, bi-pin
LQ8= large halogen, 6V, 12V- 8W, bi-pin
LQ12= large halogen, 6V, 12V-12W, bi-pin
LQ20= large halogen, 6V, 12V, 24V-20W, bi-pin
LQ55= large halogen, 12V-55W, H3
LQ70= large halogen, 24V-70W, H3
LS8= large tungsten, 6V, 12V-8W, sealed beam
LS18= large tungsten, 6V, 12V-18W, sealed beam
LS25= large tungsten, 6V, 12V-25W, sealed beam
LH8= large halogen, 6V, 12V-8W, sealed beam
LH12= large halogen, 6V, 12V-12W, sealed beam
LH20= large halogen, 6V-20W, sealed beam
options
A= ammeter
CT= cab-tire
D3= time delay
(15 mins.)
D6= 6 cct. fuse panel
IT= A
C terminal block
ITOT= AC/DC terminal
block
LB= light activated test
switch
LD= lamp disconnect
(programmable)
OT= DC terminal block
R3= remote test
receiver*
TL= twist-lock plug
(120V)**
V= voltmeter
*Minimum lamp load
required: 20% of unit
capacity
*Not all options available
with NEXUS® System.
Please consult your sales
representative
*Polar white or black cabinet only
e x a m p l e : L D X 6 - 1 0 8 TA D 2 R Q 8 , L D X 1 2 - 1 0 0 TA D 2 R M 1 2 , L D X 2 4 - 1 4 4 TA D 2 R L 1 5 0 M D
113
*R4= r emote test
transmitter
(sold separately)
**120V is standard
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
LDX-TS Series
T-Bar 12V MR16 LED Unit
Fully recessed units
for T-Bar mounting in
suspended ceilings.
The LDX-TS Series battery units are
designed for T-bar ceiling grid installation.
This slim-line, unobtrusive unit is ideally
suited for any commercial location where
there is limited wall space and where
the greater directional flexibility of
ceiling-mounted heads is needed to provide
greater light distribution.
Supply and install a complete emergency lighting system as described herein and shown on the drawings.
The Ready-Lite® Smart Diagnostic Micro controller board shall supply the rated load for a minimum of a 30
minutes to 87.5% of the rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and be CSA listed.
The unit shall have an output of V. The charger shall be fully computer tested and its charge voltage factory
set to ± 1% tolerance. Chargers with field-adjusted potentiometers are not acceptable. A pulse-type charger
shall be employed to promote long battery life and reduce the potential for grid corrosion.
The charger shall provide a continuous high charge to recharge the battery, when the battery is at full capacity,
the charger will shut-off. Periodically the charger shall provide a pulse of energy to keep the battery topped
off. The charger shall be current limited, temperature compensated, short-circuit proof and reverse polarity
protected. The unit shall be furnished with an electronic lockout circuit, which will connect the battery when
the AC circuit is activated, and an electronic brownout circuit, which will activate the emergency lights when
utility power dips below 75% of nominal voltage. A low voltage battery protection circuit shall be provided and
will disconnect the battery from the fused output circuit at the end of discharge. The unit shall self-test for 1
minute every 30 days, 10 minutes on the 6th month and 30 minutes every 12 months.
The unit shall be capable of full recharge in compliance with CSA specifications. The unit shall be furnished
with sealed dust tight relay, a test switch and seven diagnostic LED indicator lights to continuously monitor
the status of the unit: Battery Failure, Battery Disconnected, Charger Failure, Lamp Failure, Service Alarm,
AC “ON”, Charger High Rate. The unit shall be T-bar mounted and come complete with tool-less emergency
lighting heads requiring no tools to adjust or aim.
The unit shall be Ready-Lite® model:
replacement lamps
ordering code
lamp type
voltage/wattage
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
Features
• Rugged steel cabinet with
corrosion-resistant undercoating
• Battery and charger are concealed
above the ceiling level in the unit
cabinet
• Removable panel provides easy
access to battery and circuitry
• Test switch and LED indicators are
mounted on the visible bottom panel
• Units mount quickly and easily
in standard 2’ x 2’ or 2’ x 4’ grids
without any additional hardware
• Solid-state pulse-type charger
– current-limited, temperaturecompensated, short-circuit proof
and reverse-polarity protected
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator lights
• Long-life, maintenance-free Lead Acid
battery
• Standard 120/347VAC input voltage
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• CSA C22.2 No. 141 certified
• Available with 4 selection of 4W, 5W or
6W LED lamps
• Vandal resistance clear polycarbonate
lens
• Optional tamper-proof screws available
.
POwer consumption and unit rating
model
LDX12-36TS
LDX12-72TS
ac specs
120/347VAC
114
wattage capacity
30min
1h00
1h30
2h00
4h00
0.09/0.03A
36
21
15
12
-
0.15/0.06A
72
42
30
24
12
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Dimensions
Dimensions are approximate and subject to change.
LDX-TS Series
3-1/4” [8.2 cm]
T-Bar 12V MR16 LED Unit
10-1/2” [26.6 cm]
7-1/4” [18.3 cm]
23-3/4” [60.3 cm]
4-5/8” [11.8 cm]
ordering information
Series
Capacity
LDX12= 12V
36TS= 36W
72TS= 72W
Special Options
Blank= standard
AD= auto-diagnostics,
audible
ADN= auto-diagnostics,
non-audible
NEX= NEXUS® wired
system interface*
NEXRF= N
EXUS® wireless
system interface*
# of Heads
2= two heads
3= three heads
Lamp Wattage
LD7= 12V-4W
MR16 LED
LD9= 12V-5W
MR16 LED
LD10= 12V-6W
MR16 LED
Colour
Blank= factory
white
A.C.Voltage
Blank= 120/347VAC
input
Options
CT= cabtire
IT= AC terminal block
ITOT= AC/DC terminal block
OT= DC terminal block
D= time delay (programmable)
LB= light activated test switch
LD= lamp disconnect
R3= remote test receiver*
TL= twist lock plug (120V)**
TP= tamper-proof screws***
*R4= remote test transmitter
(sold separately)
* Not all options available with
Nexus® System.
Please consult your sales
representative.
**120V is standard
***990.0119-RL= tamper proof bit
(sold separately)
E XAMPL E : L D X 1 2 3 6 T S 2 L D 7 O T
115
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
Escape™ C29
Series
Thermoplastic
The Contractor will install the Ready-Lite® Escape™ C29 Series battery unit. The emergency lighting system
shall consist of fully automatic equipment with two MR16 glare-free halogen heads. Each unit shall contain
a fully automatic, solid state charger with test switch and AC on pilot lights. The unit shall contain a sealed
transfer circuit and low voltage disconnect circuit. The battery shall be 6V with a capacity of 29W for 30
minutes.
The unit shall be CSA C22.2 no 141.
The unit shall be Ready-Lite® model:
.
wire guards
460.0100-RL
wall mount or ceiling mount
Features
• Injection-molded thermoplastic housing
• Two adjustable glare-free light heads
• Test switch and charge rate indicators
• Emergency mode: min. 90 minutes
• Universal 120/347 VAC input
• CSA C22.2 No. 141 certified
• Innovative snap together design allows
for fast installation
REPLACEMENT LAMPS
ordering code
lamp type
voltage/ wattage
580.0072-RL
MR16
6V-5.4W
580.0079-RL
MR16
6V-10W
Dimensions
Dimensions are approximate and subject to change.
4-1/8” [10.5 cm]
5-1/2” [14 cm]
12-1/8” [30.8 cm]
POwer consumption and unit rating
model
ac specs
dc specs
C29
120/347VAC
0.06/0.03 A
less than 6W
6V-10.8W
min. 90 minutes
C29/10
120/347VAC
0.06/0.03 A
less than 6W
6V-20W
min. 30 minutes
ordering information
Series
C
capacity
29= 6V-29W
AC voltage
Blank= 120/347VAC
E XAMPL E : C 2 9
116
# of lamps and type
Blank= 2X MR16 halogen, 6V-5.4W (standard)
/10= 2X MR16 halogen, 6V-10W
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
7-5/16” [18.6cm]
7-5/16"
2-3/16"
2-3/16” [5.5cm]
RCSB Series
Miniature LED Battery Unit
Features
4-1/4” [10.8cm]
4-1/4"
•Fully adjustable LED glare-free lens
•3.6V 1W long life LED light source,
6000K
•Remote capacity for one dedicated
remote head (RCSRD only).
•Dual voltage input capability 120/277VAC
•Automatic, temperature compensated,
pulse type charger
•Low voltage disconnect prevents over
discharge of battery
•Automatic brownout protection
•Sealed maintenance-free 3.6V
POwer consumption and unit rating
Model
AC Specs
RCSB-6
120/277VAC
DC Specs
0.06/0.07 A
0.4/0.6 W
NiMH battery
min. 90 minutes
R SC fa m i ly
RSC Exit P. 54
RCSC Combo P. 55
Nickel-Metal Hydride battery offering 90
minutes of emergency lighting
•Battery lock-out prevents discharge
during installation
•Red LED charger monitor
•Momentary test switch allows for quick
operational check
•Injection-molded thermoplastic ABS
housing
•Rear keyhole slots and universal
knock-outs to mount to any standard
4” junction box
•Fast and easy installation with
snap-together design
•Ceiling or wall mount installation
•Meets CSA C22.2 no.141-10
•Comes standard with one (1) year
warranty
RCSR Remote P. 148
ordering information
Series
RCSB
capacity
-6= 6W-3.6V
voltage
Blank= 120/277VAC
Example: RCSB-6
117
lamp
Blank= 2X 1W LED
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
LDXC Series
Steel, compact, 6V and 12V
Features
• Compact steel cabinet with
corrosion-resistant undercoating
• Quick and easy installation –
pre-assembled cordset, no batteries or
board to remove before installation
• Universal Spider knockout pattern for
junction box mounting
• Fully automatic solid-state charger with
test switch and AC-on pilot light
• Sealed dust-proof transfer relay circuit
and low-voltage disconnect
• Long-life, maintenance-free sealed
Lead Acid battery
• NEXUS® compatible. Please consult
your sales representative
• Heads require no tools for orientation
• Standard input 120 VAC with line cord
installed
• 120/347 VAC without line cord
• Certified CSA C22.2 No.141
The contractor shall install the Ready-Lite® LDXC Series battery units. The emergency lighting system shall
consist of fully automatic equipment with two emergency lighting heads. The unit shall be rated
V with
a capacity of
W for 30 minutes of emergency operation.
The charger shall be factory set with a charging voltage tolerance of ± 1% to enable a longer battery life. The
emergency light heads shall require no tools for adjusting or aiming. The metal cabinet shall be made of steel
with anti-corrosion undercoating.
The unit equipped with the auto-test micro-controller board shall self-test 1 minute every 30 days, 10 minutes
every 6 months and 30 minutes every 12 months. The unit shall be supplied with a test switch and diagnostic
LED indicator lights to continuously monitor the status of the unit: Battery Failure, Battery Disconnect, Charger
Failure, Lamp Failure, Service Alarm, main voltage AC “ON”, Charger High Rate.
The unit shall be CSA Certified to C22.2 no.141.
The unit shall be Ready-Lite® model:
.
Wire guards
460.0080-RL
wall mount
POwer consumption and unit rating
MODEL
WATTAGE CAPACITY
AC SPECS
30MIN
1H00
1H30
2H00
LDXC627
0.06/0.02 A
27
15
11
9
-
LDXC644
0.18/0.06 A
44
26
18
15
7
12
LDXC672
120/347 VAC
4H00
0.19/0.07 A
72
42
30
24
LDXC1244
0.31/0.10 A
44
26
18
15
7
LDXC1272
0.31/0.10 A
72
42
30
24
12
REPLACEMENT LAMPS
ordering code
lamp type
570.0016-RL
mini tungsten
voltage/ wattage
6V-9W
570.0025-RL
mini tungsten
12V-9W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
For the complete list, please see the lamp chart on pages 166 to 168
118
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
9-1/8” [30.8 cm]
LDXC Series
Steel, Compact, 6V and 12V
12-3/4” [30.8 cm]
3-1/4” [30.8 cm]
ordering information
Series
capacity
LDXC6= 6V
-27= 27W
-44= 44W
-72= 72W
LDXC12= 12V
-44= 44W
-72= 72W
special options
# of heads
heads style/wattage
colour
AC voltage
options
Blank= no options
AD= auto-diagnostic*
ADN= auto-diagnostic,
non-audible*
NEX= NEXUS® system
interface*
NEXRF= wireless
NEXUS®
system
interface*
Blank= no
heads
1= one head
2= two heads
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
RMH20= MR16-IR, 12V-20W,
high-output
LT9= large tungsten, 6V, 12V-9W, wedge base
LT18= large tungsten, 12V-18W, wedge base
LT25= large tungsten, 6V, 12V-25W, DCB
RT9= mini tungsten, 6V, 12V-9W, wedge base
RT18= mini tungsten, 12V-18W, wedge base
RQ8= mini halogen, 6V, 12V-8W, bi-pin
RQ12= mini halogen, 6V, 12V-12W, bi-pin
LQ8= large halogen, 6V, 12V- 8W, bi-pin
LQ12= large halogen, 6V, 12V-12W, bi-pin
LQ20= large halogen, 6V, 12V-20W, bi-pin
LS8= large tungsten, 6V, 12V-8W, sealed
beam
LS18= large tungsten, 6V, 12V-18W, sealed
beam
LS25= large tungsten, 6V, 12V-25W, sealed
beam
LH8= large halogen, 6V, 12V-8W, sealed
beam
LH12= large halogen, 6V, 12V-12W, sealed
beam
LH20= large halogen, 6V-20W, sealed beam
Blank=
factory white
BK= black
Blank= 120VAC c/w
linecord
U277= 277VAC input
U347= 120/347VAC
input
Blank= no options
CT= cab-tire
TL= twist-lock
plug (120V)*
*Not available in 6V-72W
*Not all options available
with NEXUS® System.
Please consult your
sales representative
*120V is standard
E XAMPL E : L D X C 6 - 2 7 2 R T 9
119
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
LDXA Series
Decorative, 6 and 12V
Features
• Rugged steel cabinet with
corrosion-resistant undercoating
• Removable front panel on cabinet
provides easy access and allows unit
to be mounted at ceiling height
• Solid-state pulse-type charger
current-limited, temperature
compensated, short-circuit proof
and reverse-polarity protected
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator light(s)
• Long-life, maintenance-free lead
acid battery
• NEXUS® compatible. Please consult
your sales representative
• CSA C22.2 No. 141 Certified
Supply and install the Ready-Lite® LDXA Series battery units. The battery unit shall come complete with two
MR16 emergency lighting heads. The unit shall be rated for dual voltage120/347V, 60 Hz and shall provide
power to the nominal load for at least 30 minutes to 87.5% of the nominal voltage of the battery. The charger
shall be factory set with a charging voltage tolerance of ±1% to enable a longer battery life. The emergency
light heads shall be fully adjustable and protected by a clear cover, made of shock-resistant polycarbonate.
The protective cover shall be designed to facilitate lamp replacement. The heads shall be installed at the
bottom of the unit, providing illumination in any downward direction. The emergency light heads shall require
no tools for orientation.
The unit cabinet shall be made of steel with anti-corrosion undercoating. The unit equipped with the auto-test
diagnostic micro-controller board shall self-test 1 minute every 30 days, 10 minutes the every 6 months and
30 minutes every 12 months. The unit shall be supplied with a test switch and diagnostic LED indicator lights
to continuously monitor the status of the unit: Battery Failure, Battery Disconnect, Charger Failure, Lamp
Failure, Service Alarm, main voltage AC “ON”, Charger High Rate.
The unit shall be CSA Certified to C22.2 no.141.
The unit shall be Ready-Lite® model:
.
Wire guards
460.0080-RL
wall mount
REPLACEMENT LAMPS
ordering code
lamp type
580.0074-RL
MR16
voltage/ wattage
6V-6W
580.0079-RL
MR16
6V-10W
580.0080-RL
MR16
12V-12W
580.0068-RL
MR16
12V-20W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
Power consumption and unit rating
MODEL
AC SPECS
WATTAGE CAPACITY
1H30
2H00
LDXA627
0.06/0.02 A
27
15
11
9
-
LDXA644
0.18/0.06 A
44
26
18
15
7
12
LDXA672
30MIN
1H00
4H00
0.19/0.07 A
72
42
30
24
LDXA1244
0.31/0.10 A
44
26
18
15
7
LDXA1272
0.31/0.10 A
72
42
30
24
12
120/347VAC
120
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
12-3/4” [32.4 cm]
3-3/8” [8.6 cm]
LDXA Series
9” [22.9 cm]
Decorative, 6 and 12V
ORDERING INFORMATION
series
capacity
LDXA6= 6V
-27= 27W
-44= 44W
-72= 72W
LDXA12= 12V
-44= 44W
-72= 72W
special options
Blank= no options
AD= auto-diagnostic*
ADN= auto-diagnostic,
non-audible*
NEX= NEXUS® system
interface*
NEXRF= wireless NEXUS®
system interface*
# of heads
2= 2 heads
heads style/wattage
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen,
12V-12W
RM20= MR16 halogen,
12V-20W
RMH20= MR16-IR, 12V-20W,
high-output
colour
Blank= factory
white
BK= black
AC voltage
options
Blank= 120/347VAC
U277= 277VAC input
Blank= no options
CT= cab-tire
LC= line cord (120V)
TL= twist-lock plug
(120V)*
*Not available in 6V-72W
*Minimum lamp load
required: 20% of unit
capacity
*Not all options available
with NEXUS® System.
Please consult your sales
representative
*120V is standard
E XAMPL E : L D XA 6 - 2 7 2 R M 6
121
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
ultima™ Series
Thermoplastic, 6 and 12V
Features
• Designed with aesthetics, ease of
installation and performance in mind
• Simple, compact and contemporary
design
• Wall-mount, ceiling-mount flat or
pendant installation
• Two-piece housing of injection molded
thermoplastic
• Two MR16 halogen lamps, shielded
by clear polycarbonate covers
• Available with long lasting MR16 LED
lamps
• Sealed, maintenance-free,
Lead-Calcium battery
• Dual voltage input: 120/347VAC
• Up to 150W of total battery capacity
• Auto-diagnostics (optional)
• NEXUS® interface (optional)
• Certified CSA 22.2 No.141
Supply and install the Ready-Lite® Ultima™ Series battery unit equipment. The unit construction shall include
a housing and a front cover of high-impact thermoplastic moulded in white. No screws shall be necessary to
hold the front cover to the housing. The unit shall be equipped with two emergency heads with adjustable
swivels and MR-16 lamps of
V
W protected by snap-on shock-absorbent, clear polycarbonate
covers. The unit shall be suitable for wall mount or as otherwise specified. The unit equipment shall have a
dual-voltage input of 120/347VAC and shall be equipped with a test switch and a green pilot light, located
on the left side.
The housing shall host the battery and the battery charger. The battery charger and other unit functions shall
be driven by a micro-controller. All electronic circuitry shall be installed on a single printed circuit board.
When specified, the unit equipped with auto-test shall automatically self-test for one minute every 30 days,
10 minutes every 6 months and 30 minutes annually. When a fault is detected, the bi-colour pilot light shall
turn from green to red and start flashing. A legend on a label next to the pilot light shall display the source of
failure: battery, charger circuitry or lamp load.
The unit equipment shall be listed to the standard CSA 22.2 No.141.
The unit equipment shall be Ready-Lite® model:
.
Wire guards
460.0080-RL
wall mount or ceiling mount
REPLACEMENT LAMPS
ordering code
lamp type
580.0079-RL
MR16 halogen
voltage/ wattage
6V-10W
580.0080-RL
MR16 halogen
12V-12W
580.0064-RL
MR16 halogen
12V-20W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
Power consumption and unit rating
Model
AC Specs
30min
640
Wattage Capacity
1h00
1h30
2h00
4h00
40
23
16
12
-
72
42
30
24
12
80
44
32
26
13
12120
120
70
50
40
20
12150
150
84
60
48
24
672
1280
120/347VAC
0.25 / 0.09 A
u l t i m a ™ fa m i ly
Ultima™ Exit P. 53
Ultima™ Combo P. 56-57
122
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
ultima™ Series
12-1/4” [31.0 cm]
10-5/8” [26.9 cm]
Thermoplastic, 6 and 12V
3-7/8” [9.8 cm]
ordering information
Series
Capacity
ULT6= 6V
40= 40W
72= 72W
ULT12= 12V
80= 80W
120= 120W
150= 150W
Unit Type
Heads
Blank= standard
0= no
AD= auto-diagnostic*
heads
ADN= auto-diagnostic, non-audible*
2= two
®
NEX= NEXUS system interface*
heads
NEXRF= wireless NEXUS® system interface*
Lamps
colour
Voltage
LD1= MR16 LED, 6V-4W
W= factory Blank= 120/347VAC
LD7= MR16 LED, 12V-4W
white 2= 120/277VAC
LD9= MR16 LED, 12V-5W
B= black
LD10= MR16 LED, 12V-6W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V-12W
RM20= MR16 halogen, 12V-20W
*Minimum lamp load required: 20% of unit
capacity
*Not all options available with NEXUS® System.
Please consult your sales representative
E XAMPL E : U LT 6 4 0 2 R M 6 W
123
Options
Blank= no options
CM= ceiling mount
D3= time delay
(15 mins.)
LC= line cord (120V)
PM= p
endant mount
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
The contractor will install the Ready-Lite® LES18P Series compact emergency lighting unit. The unit housing
shall be made of injection moulded, high impact, corrosion resistant thermoplastic. The unit dimensions
including the emergency heads shall be less than 24.1cm x 17.1cm x 12.4cm. The unit shall be rated
120VAC 60Hz input and 6VDC nominal output. The unit shall contain a fully automatic, solid-state battery
charger with test switch and AC-on pilot light. The charger shall be computer tested and shall contain
low-voltage disconnect circuitry to protect the battery from deep discharge.
The battery shall be maintenance-free, sealed lead-calcium and shall supply the emergency heads with power
for minimum 60 minutes during an AC power failure. The unit shall include two emergency heads built of
flame-retardant thermoplastic and shall include two mini-tungsten 6V-9W lamps.
The unit shall be CSA C22.2 no 141.
The unit shall be Ready-Lite® Model:
.
LES18P Series
Compact Emergency
Lighting Units
Features
wire guards
• Compact emergency lighting unit
available in factory white
• Fully automatic, solid state, voltage
sensitive charger with test switch and
AC-on pilot light
• Sealed dust-proof transfer relay circuit
and low voltage disconnect
• Long-life, maintenance-free sealed
Lead-Calcium battery
• Housing and heads constructed of
injection molded, high impact, corrosion
resistant thermoplastic
• 120VAC standard input
• 60 minutes run time
• CSA C22.2 No. 141 certified
460.0082-RL
wall mount or ceiling mount
replacement lamps
ordering code
lamp type
voltage/wattage
570.0016-RL
mini tungsten
6V-9W
Dimensions
Dimensions are approximate and subject to change.
6-3/4” [17.1 cm]
9-1/2” [24.1 cm]
9-7/8” [24.4 cm]
ordering information
Series
LES= compact plastic
capacity
18P= 18W
options
Blank= 6V-9W
E XAMPL E : L E S 1 8 P
124
Colour
Blank= factory white
voltage
Blank= 120VAC input
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
Supply and install the Ready-Lite® B-29 Series battery unit. The unit shall come standard with housing and
back plate of white thermoplastic and two prismatic-shaped lenses made of clear polycarbonate. The unit
shall contain a fully automatic, solid-state charger circuit with test switch button and AC-on LED pilot light. The
charger shall include features like brownout detection, low-battery disconnect and instant transfer.
The unit shall be equipped with two incandescent emergency lamps of 6V-5.4W and a maintenance-free
Lead-Calcium battery with five-year life expectancy. The total output for emergency lighting shall be 6V-29W
for minimum 30 minutes. The unit shall come standard with a DC-remote cable with in-line fuse and provide
18W of remote capacity.
The unit shall be listed CSA C22.2 no.141
The unit shall be Ready-Lite® model:
.
B-29 Series
Rapid Installation
Decorative Thermoplastic
Features
wire guards
460.0100-RL
• Impact-resistant thermoplastic
construction
• Wall or ceiling mount
• Pre-wired AC quick-connect plug for
fast and easy installation
• Dual-voltage input: 120/347 VAC
• Two wedge-base, incandescent lamps
of 6V- 5.4W
• DC-remote fused output of 6V-18W
• Fully automatic, solid-state battery
charger with brownout protection,
low-voltage battery disconnect, manual
test switch and LED pilot light
• Maintenance-free, sealed Lead-Calcium
battery with life expectancy of five years
• Listed CSA C22.2 No.141
wall mount or ceiling mount
REPLACEMENT LAMPS
ordering code
lamp type
voltage/ wattage
570.0012-RL
tungsten, wedge base
6V-5.4W
Dimensions
Dimensions are approximate and subject to change.
2-3/4”
[7.0 cm]
12-3/8” [31.4 cm]
5”
[12.6 cm]
POwer consumption and unit rating
model
B-29
wattage capacity
ac specs
120/347VAC
0.06/0.02 A
30min
1h00
1h30
2h00
4h00
29W
17W
12W
10W
-
ordering information
Series
B
unit capacity
29= 6V-29W
AC voltage
Blank= 120/347VAC (standard)
E XAMPL E : B 2 9
125
options
C= line cord
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
Model No.:
Typical specifications
LDX Series
6, 12 and 24V
10-year life expectancy,
maintenance-free
emergency lighting units.
The LDX Series battery units combine long life
expectancy, high-performance design and a
reasonable initial cost outlay. Ideally suited
for a range of commercial applications, the
long-life lead acid battery is specifically
recommended for environments where the
unit will be exposed to large variances in
ambient temperature.
Supply and install a complete emergency lighting system as described herein and shown on the drawings.
The Ready-Lite® Smart Diagnostic micro-controller board shall supply the rated load for a minimum of a 1/2
hour to 87.5% of the rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and be CSA listed.
The unit shall have an output of:
V and
W. The charger shall be fully computer tested and its
charge voltage factory set to ± 1% tolerance. Chargers with field-adjusted potentiometers are not acceptable.
A pulse-type charger shall be employed to promote long battery life and reduce the potential for grid corrosion.
The charger shall provide a continuous high charge to recharge the battery, and when the battery is at full
capacity, the charger will shut off. Periodically the charger shall provide a pulse of energy to keep the battery
topped off. The pulse charger shall be precisely regulated and shall charge the battery in relation to its temperature, state or charge and input voltage fluctuations. The charger shall be current limited, temperature
compensated, short-circuit proof and reverse polarity protected.
The unit shall be furnished with an electronic lockout circuit, which will connect the battery when the AC circuit
is activated, and an electronic brownout circuit, which will activate the emergency lights when utility power dips
below 75% of nominal voltage. A low voltage battery protection circuit shall be provided and will disconnect
the load when the battery reaches the end of discharge. The unit shall self-test for 1 minute every 30 days,
10 minutes every 6 months and 30 minutes every 12 months. The unit shall be capable of full recharge in
compliance with CSA specifications. The unit shall be furnished with a sealed dust tight relay, a test switch
and diagnostic LED indicator lights to continuously monitor the status of the unit: Battery Failure, Battery
Disconnected, Charger Failure, Lamp Failure, Service Alarm, AC “ON”, Charger High Rate. The emergency
lighting heads shall require no tools for orientation.
The unit shall be Ready-Lite® model:
.
wire guards
Features
• Rugged steel cabinet with
corrosion-resistant undercoating
• Removable front panel on cabinet
provides easy access and allows the
unit to be mounted at ceiling height
• Solid-state pulse-type charger
– current-limited, temperature
compensated, short-circuit proof and
reverse-polarity protected.
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator lights
• Long-life, maintenance-free lead
acid battery
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• CSA C22.2 No. 141 certified
• Standard 120/347 VAC input with line
cord kit
460.0078-RL
wall mount
“A” cabinet
460.0081-RL
wall mount
“B” cabinet
460.0034-RL
wall mount
“C” cabinet
ordering code
lamp type
voltage/wattage
570.0016-RL
mini tungsten (RT9)
6V-9W
570.0025-RL
mini tungsten (RT9)
12V-9W
24V-9W
replacement lamps
570.0045-RL
mini tungsten (RT9)
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
For the complete list, please see the lamp chart on pages 150 to 152
cabinet
dimensions
c
a
b
d
e
A
13-1/4“ (33.7 cm)
3-5/8“ (9.2 cm)
10-1/2“ (26.7 cm)
14-1/4“ (36.2 cm)
16-1/2“ (41.9 cm)
B
16-1/8“ (40.9 cm)
5-1/2“ (13.9 cm)
10-1/4“ (26.0 cm)
13-7/8“ (35.2 cm)
16-1/8“ (41.0 cm)
C
23-1/8“ (58.7 cm)
5-1/2“ (13.9 cm)
10-1/4“ (26.0 cm)
13-7/8“ (35.2 cm)
16-1/8“ (41.0 cm)
dimensions
Dimensions are approximate and subject to change.
d
c
a
126
b
e
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
POwer consumption and unit rating
model
ac specs
wattage capacity
30 min
1h00
1h30
2h00
4h00
LDX636
0.10/0.04 A
36
21
15
12
6
LDX672
0.22/0.08 A
72
42
30
24
12
LDX6108
0.22/0.08 A
108
63
45
36
18
LDX6180
0.22/0.08 A
180
105
75
60
30
LDX1236
0.09/0.03 A
36
21
15
12
6
LDX1272
0.15/0.06 A
72
42
30
24
12
LDX12100
0.34/0.12 A
100
58
42
33
17
LDX12144
0.40/0.14 A
144
84
60
48
24
LDX12216
0.41/0.14 A
216
117
83
67
33
0.41/0.14 A
250
144
100
38
42
LDX12360
0.41/0.14 A
360
200
144
108
60
LDX24144
0.43/0.15 A
144
84
60
48
24
LDX24200
0.55 / 0.20 A
200
117
83
67
33
LDX24288
0.67 / 0.23 A
288
168
120
96
48
LDX24350
0.67 / 0.23 A
350
200
144
120
60
LDX24432
0.67 / 0.23 A
432
250
180
144
72
LDX24550
0.88 / 0.33 A
550
320
230
180
90
LDX24720
0.88 / 0.33 A
720
420
300
240
120
LDX12250
120/347VAC
LDX Series
6, 12 and 24V
Note: Low wattage LED lamps provide extended time of emergency lighting without additional power.
ordering information
Series
capacity &
Cabinet size*
LDX6= 6V
-36= 36W (A)
-72= 72W (A)
-108= 108W (A)
-180= 180W (B)
LDX12= 12V
-36= 36W (A)
-72= 72W (A)
-100= 100W (A)
-144= 144W (A)
-216= 216W (B)
-250= 250W (B)
-360= 360W (B)
LDX24= 24V
-144= 144W (A)
-200= 200W (B)
-288= 288W (B)
-350= 350W (C)
-432= 432W (C)
-550= 550W (C)
-720= 720W (C)
*Cabinet size
is not part of
nomenclature.
special options
# of heads
Blank= no options
AD= auto-diagnostic,
audible*
ADN= auto-diagnostic,
non-audible*
NEX= NEXUS® system
interface *
NEXRF= wireless
NEXUS®
system
interface*
Blank= no
heads
1= one head
2= two
heads
3= three
heads
head style/lamp wattage
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
LD13= MR16 LED, 24V-4W
RM6= MR16 halogen, 6V-6W
RM10= MR16 halogen, 6V-10W
RM12= MR16 halogen, 12V, 24V-12W
RM20= MR16 halogen, 12V, 24V-20W
RMH20= MR16-IR, 12V-20W, high-output
LT9= large tungsten, 6V, 12V, 24V-9W, wedge base
LT18= large tungsten, 12V, 24V-18W, wedge base
LT25= large tungsten, 6V, 12V, 24V-25W, DCB
RT9= mini tungsten, 6V, 12V, 24V-9W, wedge base
RT18= mini tungsten, 12V, 24V-18W, wedge base
RQ8= mini halogen, 6V, 12V-8W, bi-pin
RQ12= m
ini halogen, 6V, 12V, 24V-12W, bi-pin
LQ8= large halogen, 6V, 12V- 8W, bi-pin
LQ12= large halogen, 6V, 12V-12W, bi-pin
LQ20= large halogen, 6V, 12V, 24V-20W, bi-pin
LQ55= large halogen, 12V-55W, H3
LQ70= large halogen, 24V-70W, H3
LS8= large tungsten, 6V, 12V-8W, sealed beam
LS18= large tungsten, 6V, 12V-18W, sealed beam
LS25= large tungsten, 6V, 12V-25W, sealed beam
LH8= large halogen, 6V, 12V-8W, sealed beam
LH12= large halogen, 6V, 12V-12W, sealed beam
LH20= large halogen, 6V-20W, sealed beam
colour
AC vOltage
options
Blank=
factory
white
BK= black
Blank= 120/347
VAC input
U277= 277VAC
input
A= ammeter
CT= cab-tire
D3= time delay
D6= 6 cct. fuse
panel
IT= AC terminal
block
ITOT= AC/DC
terminal block
LB= light activated
test switch
LD= lamp
disconnect
OT= DC terminal
block
R3= remote test
receiver**
TL= twist-lock plug
(120V)***
V= voltmeter
ZCP= zone control
panel
(only 24V)* n
*See page 203 for
complete ordering
info
*Minimum lamp load
required: 20% of unit
capacity
*Not all options available
with NEXUS® System.
Please consult your
sales representative
**R4= remote test
transmitter
(sold
separately)
***120V is standard
E XAMPL E : L D X 6 - 3 6 2 L D 1 B K I T
127
Type:
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Made in Canada
Model No.:
Typical specifications
Tuf-nm Series
NEMA-4X Certified
Features
• Fully gasketed cast aluminum back
plate with clear polycarbonate
cover – NEMA-4X Certified
• Comes standard with non-audible
advanced diagnostic, 10 minutes
time delay and lamp disconnect
• Audible warning and time delay
functions can be enabled or disabled
during installation
• Micro-controller diagnostic system tests,
detects and indicates battery, charger
circuitry or MR16 lamp failures
• Non-intrusive magnetic test switch
• Long-life, maintenance-free sealed
lead-acid battery
• 1/2” rigid conduit entry on top and back
• Can be installed on 4” junction boxes
• Comes standard with tamper-proof
screws and bit
• Cold weather option -40ºC (-40ºF)
• NSF Certified for food processing plants
• CSA C22.2 No. 141 Certified
• NEXUS® compatible
• Standard 120/347VAC input voltage
Supply and install the Ready-Lite® NEMA-4X Certified TUF-NM Series battery unit. Specifically designed for high
abuse areas, wet locations, and cold weather (CW option -40°C (-40°F)), the housing shall consist of a fully
gasketed Die-Cast aluminum back plate and a clear heavy-duty UV resistant polycarbonate cover. The heads
shall be fully adjustable without tools and the lamps shall be high efficiency halogen MR16. The standard unit
shall be equipped with tamper-proof screws and bits. The Ready-Lite® Advanced Diagnostic Micro-controller
charger board shall supply the rated load for a minimum of 30 minutes to 87.5% of the rated battery voltage.
The charger incorporates lockout and brownout circuits, and low voltage disconnection. It protects the unit
from over-current, short-circuit, and reverse polarity.
The unit shall be rated 120/347V, 60Hz. The unit shall have an output of
V. This unit shall self-test
for 1 minute every 30 days, 10 minutes every 6 months and 30 minutes every 12 months. The unit shall be
furnished with a non-intrusive magnetic test switch. A “Service Required” lamp shall be located near the test
switch and flash when a fault is detected. A four-LED diagnostic display shall be located inside the equipment
and shall identify the source of failure (battery, charger, circuitry, or lamps).
The unit shall be Ready-Lite® model:
.
replacement lamps
ordering code
lamp type
voltage/ wattage
580.0079-RL
MR16 halogen
6V-10W
580.0080-RL
MR16 halogen
12V-12W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
n e m a - 4 x a n d n s f c e r t i f i e d fa m i ly
RNC Combo P. 64-65
TUF Exit P. 63
128
N-TUF Combo P. 66-67
RN P. 62
TUF-NM Remote P. 160-161
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
dimensions
Dimensions are approximate and subject to change. Not suitable for ceiling installation.
Tuf-nm Series
7” [17.8 cm]
17-3/4” [45.1 cm]
5-3/4” [14.6 cm]
NEMA-4X Certified
Beam Mounting
PMK Kit
(screws included)
Superstrut
Mounting
Power consumption and unit rating
MODEL
WATTAGE CAPACITY
AC SPECS
30MIN
1H00
1H30
2H00
4H00
LDX6-36NM
0.15/0.06 A
36
21
15
12
6
LDX12-72NM
0.25/0.10 A
72
42
30
24
12
0.25/0.10 A
108
63
45
36
18
0.45/0.20 A
36
-
-
-
-
0.85 A
72/108
-
-
-
-
LDX12-108NM
120/347VAC
Cold Weather 36W
Cold Weather 72/108W
120VAC
*Note: capacity depends on the ambient temperature
ordering information
series
capacity
cabinet
LDX6= 6V
LDX12= 12V
-36= 6V-36W
-72= 12V-72W
-108= 12V-108W
NM= NEMA-4X
# of heads
2= 2 heads
LAMP type
LD1= MR16 LED, 6V-4W*
LD7= MR16 LED, 12V-4W*
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
RM6= MR16 mini halogen,
6V-6W
RM10= MR16 mini halogen,
6V-10W
RM12= MR16 mini halogen,
12V-12W
RM20= MR16 mini halogen,
12V-20W
RMH20= MR16-IR, 12V-20W,
high-output
*Minimum lamp load required:
20% of unit capacity
Example: LDX6-36NM2RM6
129
colour
ac voltage
Blank= white
BK= black
GY= grey
Blank= 120/347VAC
277= 277VAC
options
Blank= no options
NEX= NEXUS® system Interface*
NEXRF= wireless NEXUS® system
interface*
CW1= cold weather 120VAC
CW3= cold weather 347VAC**
PMK= universal bracket
(sold separetely)
*Not all options available with NEXUS®
System. Please consult your sales
representative
**Available in 6V only
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
LDX-HZ Series
Battery Unit Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
n
Features
•Includes the addition of Class II Div 1&2
Groups E, F and G as well as Class III
ratings
• Certified Class I Zone 2, Groups IIA, IIB
and IIC
• Certified Class I Division 2, Groups A,
B, C and D as per CSA C22.2
No.137-M1981
• Certified temperature codes for several
types of emergency lamps
• Suited for areas with the risk of
flammable gases, vapors or liquids that
can create an explosive atmosphere
• Certified CSA C22.2 No141
• Polymeric frame, with built-in gasket
to prevent water infiltration
• Heavy-duty 1/8” thick aluminum back
plate with keyholes for secure
wall-mount installation
• Two MR16 halogen or LED lamps,
shielded by a cast aluminum housing
and a polycarbonate cover
• 5W LED emergency lights provide
60 ft of egress illumination on a 6-foot
wide path
n • 6 W LED emergency lights provide
100 ft of egress illumination on a 6-foot
wide path
• Sealed, maintenance-free, Lead-Calcium
batteries with up to 150W emergency
power
• Built-in microcontroller-based battery
charger and auto-diagnostics circuitry
• ½” electrical conduit entry on both
sides and at the top
• NEXUS® compatible (for more
information on NEXUS®, please
contact your sales representative)
Supply and install Ready-Lite® LDX-HZ Series battery units. Designed specifically for Hazardous Location
environments, the equipment frame shall be of industrial grade polymeric material with gaskets around both
sides of the contour. The frame shall be fixed between two plates made of 1/8” thick aluminum sheet. The
back plate shall include four keyholes for wall-mount installation. The front plate shall include two water-tight
lenses for pilot lights: AC-on and “Service required”. When specified, the equipment shall have attached a lower
compartment containing two emergency lights with adjustable swivels and MR-16 halogen lamps. The lamps
shall be shielded by a cast aluminum housing and protected by a shock-absorbent, transparent polycarbonate cover. The equipment shall be certified for Hazardous Locations: Class I Division 2 Groups A, B, C and D,
Class II Divison 1&2 Groups E, F and G as well as Class III. The standard equipment shall have a dual voltage
input: 120/347VAC and shall be equipped with a magnetic test switch located on the left side of the frame.
The unit shall include self-testing/auto-diagnostic functions monitored by a micro-controller and shall
automatically self test for one minute every 30 days, 10 minutes every 6 months and 30 minutes annually.
The “Service required” LED shall light when a fault is detected. A four-LED diagnostic display located inside
the equipment shall identify the source of the failure (battery, charger circuitry, lamp load).
The unit shall be listed CSA C22.2 No.141 and No. 137 – M1984
The battery unit shall be Ready-Lite® model:
.
h a z a rd o u s l o c at i o n fa m i ly c l a s s I , II a n d III
RH P. 68
TUFHZ P. 69
RHC Combo P. 70-71
HZ Combo P. 72-73
NMHZ Remote P. 164
Temperature codes (class I division 2)
lamp rating
temperature code
max. temperature
replacement lamp
6V-10W
T3C
160°C
580.0079-RL
12V-12W
T3A
180°C
580.0080-RL
12V-20WH
T2D
215°C
580.0068-RL
6V-4W LED
T4A
120°C
580.0097-RL
12V-4W LED
T4A
120°C
580.0093-RL
12V-5W LED
T4A
120°C
580.0104-RL
12V-6W LED
T4
135°C
580.0106-RL
Note: Use qualified replacement lamps to avoid risk of over-heating.
POwer consumption and unit rating
model
ac specs
LDX-36HZ
120/347VAC
0.15/0.06 A
wattage capacity
30min
1h00
1h30
2h00
4h00
36
21
15
12
-
LDX-72HZ
120/347VAC
0.30/0.10 A
72
42
30
24
12
LDX-120HZ
120/347VAC
0.30/0.10 A
120
70
50
40
20
LDX-150HZ
120/347VAC
0.30/0.10 A
150
-
72
-
-
130
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
LDX-HZ Series
14-1/2” [36.8 cm]
Battery Unit Hazardous
Locations: Class I Div 2,
Class II Div 1&2 and Class III
3-1/2” [8.7 cm]
6-1/4” [15.9 cm]
12-5/8” [32.1 cm]
13-3/4” [34.9 cm]
ordering information
Series
LDX6
LDX12
CAPACITY
cabinet
# of heads
lamp/wattage
-36= 6V-36W
-72= 12V-72W
-120= 12V-120W
-150= 12V-150W
HZ= class 1
zone 2
hazardous
Blank= no
heads
2= 2 heads
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED,
12V-6W
M10= MR16, 6V-10W
M12= MR16, 12V-12W
M20= MR16-IR, 12V-20W
high output
COLOUR
Blank= grey
AC Voltage
Blank=
120/347VAC
U2= 277VAC
options
AD= auto-diagnostics*
ADN= auto-diagnostics, non-audible*
NEX= NEXUS® system Interface*
NEXRF= wireless NEXUS® system interface*
*Minimum lamp load required: 20% of unit
capacity
*Not all options available with NEXUS® System.
Please consult your sales representative
E XAMPL E : L D X 6 - 3 6 H Z 2 M 1 9 A D
131
Type:
Project/Location:
Contractor:
Prepared By:
Made in Canada
NEMA-12
Date:
Model No.:
Typical specifications
LDX-I Series
6, 12 and 24V
NEMA-12 Rated
Harsh environment
emergency lighting units
with steel, thermoplastic
or fiberglass cabinets.
The LDX-I Series battery units are specifically
designed for use in industrial facilities where
equipment is exposed to dust, water, oil or
corrosive substances. NEMA-12 classified to
protect circuitry from harmful dust or liquid
sprays, sealed and gasketed unit cabinets
are available in steel, thermoplastic or
fiberglass in a variety of sizes.
Supply and install a complete emergency lighting system as described herein and shown on the drawings. The
Ready-Lite® Smart Diagnostic Micro controller board shall supply the rated load for a minimum of a 1/2 hour
to 87.5% of the rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and be CSA listed. The
unit shall have an output of
V. The charger shall be fully computer tested and its charge voltage
factory set to ± 1% tolerance. Chargers with field-adjusted potentiometers are not acceptable. A pulse-type
charger shall be employed to promote long battery life and reduce the potential for grid corrosion. The charger
shall provide a continuous high charge to recharge the battery and when the battery is at full capacity, the
charger will shut off. Periodically the charger shall provide a pulse of energy to keep the battery topped off.
The Pulse charge shall be current limited and precisely regulated by a micro-processing circuit, which samples
the battery in relation to its temperature, state or charge and input voltage fluctuations. The charger shall be
current limited, temperature compensated, short-circuit proof and reverse polarity protected.
The unit shall be furnished with an electronic lockout circuit, which will connect the battery when the AC
circuit is activated, and an electronic brownout circuit, which will activate the emergency lights when utility
power dips below 75% of nominal voltage. A low voltage battery protection circuit shall be provided and will
disconnect the battery from the fused output circuit at the end of discharge. The unit shall self-test for 1
minute every 30 days, 10 minutes every 6 months and 30 minutes every 12 months. The unit shall be capable
of full recharge in compliance with CSA specifications. The unit shall be furnished with a sealed dust tight
relay, a test switch and diagnostic LED indicator lights to continuously monitor the status of the unit: Battery
Failure, Battery Disconnected, Charger Failure, Lamp Failure, Service Alarm, AC “ON”, Charger High Rate.
The unit shall be Ready-Lite® model:
.
wire guards
460.0034-RL
replacement lamps
features
• Solid-state pulse-type charger–
current-limited, temperature
compensated, short-circuit proof and
reverse-polarity protected.
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator lights
• Long-life, maintenance-free sealed
lead acid battery
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• CSA C22.2 No. 141 certified
• Standard 120/347VAC input with line
cord kit
wall mount
model
lamp type
570.0016-RL
tungsten (WT9)
6V-9W
570.0025-RL
tungsten (WT9)
12V-9W
570.0045-RL
tungsten (WT9)
24V-9W
Cabinet size 1
Cabinet size 2, 3, 4 & 5
d
d
b
e
b
e
f
a
cabinet
voltage/wattage
a
f
c
c
dimensions
a
b
c
d
e
f
size 1 thermoplastic
11-5⁄8” [29.5 cm]
13” (33.0 cm)
5” (12.7 cm)
10-3/8” (26.4 cm)
12-15/16”(32.8 cm)
8” (20.3 cm)
size 2 fiberglass
13-1/4” (33.8 cm)
15-3/8” (38.9 cm)
6-3/4” (17.0 cm)
21” (53.3 cm)
14-3/4” (37.5 cm)
8-1/8” (20.6 cm)
size 3 fiberglass
16-3/8” (41.5 cm)
24-1/4” (61.5 cm)
9-1/4” (23.4 cm)
30-3/8” (77.3 cm)
-
-
size 4 steel
13” (33.0 cm)
13-1/4” (33.8 cm)
5-7/8” (14.8 cm)
19-1/2” (49.6 cm)
12-1/8” (30.8 cm)
13-15/16”(35.3 cm)
size 5 steel
16” (40.6 cm)
20” (50.8 cm)
9-1/8” (23.3 cm)
26-1/4” (66.7 cm)
-
-
132
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
POwer consumption and unit rating
model
ac specs
wattage capacity
30min
1h00
1h30
2h00
LDX6-36
0.10/0.04A
36
21
15
12
4h00
6
LDX6-72
0.22/0.08A
72
42
30
24
12
LDX6-108
0.22/0.08A
108
63
45
36
18
LDX6-180
0.22/0.08A
180
105
75
60
30
LDX12-36
0.09/0.03A
36
21
15
12
6
LDX12-72
0.15/0.06A
72
42
30
24
12
LDX12-100
0.34/0.12A
100
58
42
33
17
LDX12-144
0.40/0.14A
144
84
60
48
24
0.41/0.14A
200
117
83
67
33
LDX12-250
0.41/0.14A
250
144
100
83
42
LDX12-360
0.43/0.15A
360
200
144
108
60
LDX24-144
0.55/0.20A
144
84
60
48
24
LDX24-288
0.67/0.23A
288
168
120
96
48
LDX24-350
0.67/0.23A
350
200
144
120
60
LDX24-432
0.67/0.23A
432
250
180
144
72
LDX24-550
0.88/0.33A
550
320
230
180
90
LDX24-720
0.88/0.33A
720
400
288
216
120
LDX12-200
120/347VAC
LDX-I Series
6, 12 and 24V
NEMA-12 Rated
ordering information
Series
capacity
LDX6= 6V
-36= 36W
-72= 72W
-108= 108W
-180= 180W
LDX12= 12V
-36= 36W
-72= 72W
-100= 100W
-144= 144W
-200= 200W
-250= 250W
-360= 360W
LDX24= 24V
-144= 144W
-288= 288W
-350= 350W
-432= 432W
-550= 550W
-720= 720W
housing
Special options
# of heads
head style/lamp wattage
options
ITC= thermoplastic
cabinet
IFG= standard
fiberglass
ISC= heavy duty
steel cabinet
Blank= standard
AD= auto-diagnostic*
ADN= autodiagnostic,
non-audible*
Blank= no
heads
1= one head
2= two
heads
WT9= large tungsten, 6V, 12V,
24V-9W, wedge base
WT18= large tungsten, 12V,
24V-18W, wedge base
WT25= large halogen, 6V, 12V-25W,
DCB
WQ8= large halogen, 6V, 12V- 8W,
bi-pin
WQ12= large halogen, 6V, 12V-12W,
bi-pin
WQ20= large halogen, 6V, 12V,
24V-20W, bi-pin
WQ55= large halogen, 12V-55W, H3
WQ70= large halogen, 24V-70W, H3
WS8= large tungsten, 6V, 12V-8W,
sealed beam
WS18= large tungsten, 6V, 12V18W, sealed beam
WS25= large tungsten, 6V, 12V25W, sealed beam
WH8= large halogen, 6V, 12V-8W,
sealed beam
WH12= large halogen, 6V, 12V-12W,
sealed beam
WH20= large halogen, 6V-20W,
sealed beam
WSR8= large rubber, tungsten,
6V-8W, sealed beam
WSR18= large rubber, tungsten,
6V, 12V-18W, sealed beam
WSR25= large rubber, tungsten,
6V, 12V-25W, sealed beam
WHR8= large rubber, halogen,
6V, 12V-8W, sealed beam
WHR12= large rubber, halogen,
6V, 12V-12W, sealed beam
WHR20= large rubber, halogen,
6V-20W, sealed beam
NEX= NEXUS® system
interface**
NEXRF= wireless
NEXUS®
system
interface**
A= ammeter
D= time delay
(programmable)
FP= food processing
lens*
IT= AC terminal block
ITOT= A
C/DC terminal
block
LB= light activated test
switch
LC= line cord (120V)
LD= lamp disconnect
OT= DC terminal block
R3= remote test
receiver*
TL= twist-lock plug
(120V)***
V= voltmeter
*R4= r emote test
transmitter
(sold separately)
**Not all options
available with NEXUS®
System. Please
consult your sales
representative
* Minimum lamp load
required: 20% of unit
capacity
***120V is standard
E XAMPL E : L D X 1 2 - 1 4 4 I S C 2 W Q 5 5 A
133
voltage
Blank=
120/347VAC
input
U27= 277VAC
input
Type:
Project/Location:
Contractor:
Prepared By:
Made in Canada
NEMA-4X
Date:
Model No.:
Typical specifications
LDX-NX Series
6, 12 and 24V
NEMA-4X Rated
Features
• Delivers great pathway illumination up
to 70 feet, center to center (with MH20
lamp)
• Fully gasketed fiberglass reinforced
polyester housing - NEMA 4X
• Solid-state pulse-type charger – current –
limited, temperature-compensated,
short-circuit proof and reverse-polarity
protected
• Unit comes standard with electronic
lockout and brownout circuits
• Sealed dust-proof transfer relay, test
switch and LED indicator lights
• Long-life, maintenance-free sealed lead
acid battery
• Standard 120/347VAC input voltage
with line cord kit
• NEXUS® compatible (for more
information on NEXUS®, please consult
your sales representative)
• Certified CSA C22.2 No. 141
Supply and install the Ready-Lite ® NEMA-4X Rated LDX-NX Series battery unit. The unit shall be
specifically designed for high abuse areas and wet locations. The unit enclosure shall be of
fiberglass-reinforced polyester and shall include a hinged door, fully gasketed and locked with two corrosionresistant screws. The emergency head(s) shall be installed at the bottom of the unit and/or at both sides and
shall be covered by a UV-resistant polycarbonate cover. The bottom head shall include one or two lamps
as specified. The unit shall come with two heads at the sides, each with one MR16 lamp. The lamps shall
be high-efficiency, long-life halogen or LED type of: __V __W as specified. The lamp swivels shall be easily
adjustable without tools. The unit enclosure shall include a test switch and a pilot light. The unit shall include
sealed, maintenance-free Lead-Calcium batteries and an electronic module for the battery charger and other
emergency lighting functions. The charger shall be computer-tested and its maximum charge voltage set in
the factory with ± 1% tolerance.
A pulse-type charger shall be employed to promote long battery life and reduce the potential for grid corrosion.
The charger shall provide a continuous high charge to recharge the battery and when the battery is at full
capacity, the charger will shut off. Periodically the charger shall provide a pulse of energy to keep the battery
topped off. The charger shall be current limited, temperature compensated and short-circuit proof. The unit
shall be furnished with an electronic lockout circuit, which will connect the battery when the AC circuit is
activated, and an electronic brownout circuit, which will activate the emergency lights when utility power dips
below 75% of nominal voltage. A low voltage battery protection circuit shall be provided and will disconnect
the battery from the fused output circuit at the end of discharge. When specified, the unit equipped with the
Ready-Lite® Auto-Diagnostic feature shall include a micro-controller based charger board that will generate
an automatic test for 1 minute every 30 days, 10 minutes every six months and 30 minutes every 12 months.
The micro-controller circuitry shall ensure equipment readiness and reliability by continuously monitoring
every critical function of the unit. If a component failure occurs, the pilot light located on the front of the
unit will change color from green to red and will flash indicating a fault. A detailed diagnostic legend shall
be available next to the pilot light and shall provide fault identification (battery, charger circuitry, lamps)
for maintenance personnel.The unit shall be capable of full recharge in compliance with CSA specifications and supply the rated load for a minimum of a 1/2 hour to 87.5% of the rated battery voltage.
The unit shall be rated 120V or 347V, 60 Hz and shall have an output of: __ V __ W.
The unit shall be Ready-Lite® model: __________________________________________________________.
wire guards
460.0034-RL
wall mount
POwer consumption and unit rating
model
ac specs
LDX6-72NX
LDX6-108NX
0.22/0.08 A
LDX6-180NX
30min
wattage capacity
1h00
1h30
2h00
4h00
72
42
30
24
12
108
63
45
36
18
180
105
75
60
30
LDX12-72NX
0.15/0.06 A
72
42
30
24
12
LDX12-100NX
0.34/0.12 A
100
58
42
33
17
LDX12-144NX
0.40/0.14 A
144
84
60
48
24
0.41/0.14 A
200
117
83
67
33
0.41/0.14 A
250
120
90
83
42
LDX12-360NX
0.41/0.14 A
360
200
160
120
60
LDX24-144NX
0.55 / 0.20 A
144
84
60
48
24
LDX24-288NX
0.67 / 0.23 A
288
168
120
96
48
LDX24-350NX
0.67 / 0.23 A
350
200
144
120
60
LDX24-432NX
0.67 / 0.23 A
432
250
180
140
72
LDX12-200NX
120/347VAC
LDX12-250NX
134
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
6-1/4”
[15.7 cm]
13-1/2” [34.2 cm]
LDX-NX Series
6, 12 and 24V
NEMA-4X Rated
18-5/8” [47.3 cm]
15-1/2” [39.3 cm]
13-1/2” [34.2 cm]
19-3/4” [50.1 cm]
ordering information
Series
LDX6= 6V
LDX12= 12V
LDX24= 24V
capacity
housing
-72= 72W
-108= 108W
-180= 180W
-72= 72W
-100= 100W
-144= 144W
-200= 200W
-250= 250W
-360= 360W
-144= 144W
-288= 288W
-350= 350W
-432= 432W
NX= NEMA-4X
NX= NEMA-4X
NX= NEMA-4X
special options
# of Heads
Blank= standard
Blank= no heads
AD= auto-diagnostic* 1= single head
ADN= auto-diagnostic
bottom, one
non audible*
lamp
2= single head
bottom, two
lamps
S= no head
bottom with
single head on
each side
1S= single head
bottom with
single head
on each side,
three lamps
2S= double head
bottom with
single head
on each side,
four lamps
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
LD13= MR16 LED, 24V-4W
RM6= MR16, 6V-6W
RM10= MR16, 6V-10W
RM12= MR16, 12V, 24V-12W
RM20= MR16, 12V, 24V-20W
RMH20= MR16-IR 12V-20W,
high output
options
NEX= NEXUS® system
interface*
NEXRF= wireless NEXUS®
system interface*
D1= time delay (5 mins.)
D2= time delay (10 mins.)
D3= time delay (15 mins.)
OT= DC terminal block
*Not all options available
with NEXUS® System.
Please consult your sales
representative
*Minimum lamp load
required: 20% of unit
capacity
Example: LDX24-144NX2RM12
head style/lamp wattage
135
ac voltage
Blank= 120/347
VAC input
U27= 277VAC
input
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
SIPR Series
IP65 Linear 2’
Fluorescent Fixture
Features
• Normally On fluorescent fixture
• IP65 rated
• Polycarbonate enclosure and lens,
vandal resistant and UV stabilized
• Rust proof hardware
• Ceiling, surface or pendant mounting
• Low profile, less than 4” deep
• Ultra efficient specular reflector with
optimized shape
• 17W T8 or 24W T5HO
• High efficiency and reliable electronic
ballast
• 120VAC to 277VAC universal and
347VAC input voltage available
• CSA certified to CAN/CSA-E60598-1:02
• Certified for wet and damp locations
• Certified for AC or DC, 120V operations
Supply and install Ready-Lite® SIPR Series fluorescent fixtures as specified.
The luminaire shall operate from 120VAC to 277VAC or 347VAC and use high quality instant start or 3-step
programmed rapid start high efficiency electronic ballasts.
The body and lens shall be constructed of UV stabilized industrial grade vandal resistant polycarbonate. A
durable formed gasket shall be provided between the enclosure and the lens and shall be designed specifically
for hostile environments. The reflector shall be made of highly specular material and formed to maximize light
output efficiency. All parts shall be corrosion resistant. A metal plate used to retain the ballast and reflector
also serves to dissipate heat, therefore lengthening ballast life. Lamps shall be as specified, either T8 or T5
HO linear fluorescent lamps, 17W or 24W. The lamps shall not be supplied with the luminaire.
Models with an inverter from the RIB/FEB Series will illuminate one or two lamps during emergency
operation for at least 90 minutes upon AC failure. During power outage, dual voltage source (AC/DC)
models with an inverter from the RIB Series shall illuminate one lamp while the DC voltage is present.
The fixture shall be CSA approved and meet IP65 designation requirements.
The inverters of RIB Series shall be CSA approved.
The inverters of the FEB Series shall be CSA or cUL approved.
The fixture shall be Ready-Lite® model: _______________________________________________________.
wire guards
460.0106-RL
wall mount or ceiling mount
input rating
ordering code
SIPR8
SIPR5
input
current
120 - 277/347VAC
0.47/0.20/0.1 A
120VDC
0.3 A
120 - 277/347VAC
0.5/0.22 A
dimensions
Dimensions are approximate and subject to change.
3-3/4” [10 cm]
6-3/4” [17 cm]
18-5/8” [47 cm]
26-3/8” [67 cm]
ordering information
series
SIPR= vapour proof 24”
lamp type*
8= 2 F17T8 17W T8 lamps
5= 2 T5HO 24W T5 lamps
*Lamps not included
E XAMPL E : S I P R 8
136
voltage
Blank= 120/277VAC
3= AC only 347VAC
DC= 120/277VAC/VDC
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
Supply and install Ready-Lite® IPR Series fluorescent fixtures as specified. The luminaire shall operate from
120Vac to 277Vac or 347Vac and use high quality instant start or 3-step programmed rapid start high efficiency
electronic ballasts. The body and lens shall be constructed of UV stabilized industrial grade vandal-resistant
polycarbonate. A durable formed gasket shall be provided between the enclosure and the lens and shall be
designed specifically for hostile environments. Ultra efficient white reflector for IPR8W and specular reflector
for IPR5 and formed to maximize light output efficiency. All parts shall be corrosion resistant. A metal plate
used to retain the ballast and reflector also serves to dissipate heat, therefore lengthening ballast life.
Lamps shall be as specified, either T8 or T5 HO linear fluorescent lamps, 32W or 54W. The lamps shall not
be supplied with the luminaire. Models with an inverter from the FPSI/FPSU Series shall illuminate one or
two lamps during emergency operation for at least 90 minutes upon AC failure. During power outage, dual
voltage source (AC/DC) models with an inverter from the RIB Series shall illuminate one lamp while the DC
voltage is present. The fixture shall be CSA approved and meet IP65 designation requirements.
The inverters of RIB Series shall be CSA approved.
The inverters of the FEB Series shall be CSA or cUL approved.
The fixture shall be Ready-Lite® model: _______________________________________________________.
wire guards
460.0105-RL
wall mount or ceiling mount
power consumption
model
ac specs
IPR8W
120/277VAC
0.54/0.23 A
PF > 0.9
IPR8W3
347VAC
0.19 A
PF > 0.9
IPR5
120/277VAC
1.03/0.143 A
PF > 0.9
IPR53
347VAC
0.35 A
PF > 0.9
dimensions
Dimensions are approximate and subject to change.
IPR Series
IP65 Linear Fluorescent Fixture
Features
• IP65 rated
• Polycarbonate enclosure and lens, vandal
resistant and UV stabilized
• Rust proof hardware
• Ceiling, surface or pendant mounting
• Low profile, less than 4” deep
n • Ultra efficient white reflector for IPR8W
and specular reflector for IPR5 with
optimized shape.
• 32W T8 or 54W T5HO
• 90 minutes of emergency operation when
installed with our FPSI or FPSU inverters
• Emergency operation from external DC
low voltage power source when installed
with our 48 Series inverters
• Suitable for wet locations
• CSA certified to CSA-E60598-1: 02
3-3/4” [10 cm]
6-3/4” [17 cm]
50-3/4” [129 cm]
36” [91 cm]
ordering information
Series
IPR= 48” (122cm)
linear fluorescent
lamp type*
8W= 2
x lamps 32W T8 white
reflector
5= 2x lamps 54W T5HO
voltage
Blank= AC only
120/277VAC
3= AC only 347VAC
DC= 120VAC/VDC
accessories
Self-powered, one lamp emergency
FPSI-32= inverter for IPR8 (complete code = IPR8FPSI-32)
FEB/U= inverter for IPR8-3 (complete code = IPR8-3FEB⁄U)
FPSI⁄U= inverter for IPR5 (complete code= IPR5FPSI⁄U)
Self-powered, two lamps emergency
FPSU-28= inverter for IPR8 (complete code= IPR8FPSU-28)
FEB⁄U= inverter for IPR8-3 (complete code= IPR8-3FEB⁄U)
Fluorescent inverters, non self-powered
RIB680= 6VDC, 120VAC
RIB680U347= 6VDC, 347VAC
RIB1280= 12VDC, 120VAC
RIB1280U347= 12VDC, 347VAC
RIB2480= 24VDC, 120VAC
RIB2480U347= 24VDC, 347VAC
081282-RL= s tainless steel clips kit (10)
*Lamps not included
E XAMPL E : I P R 8 W
137
RIB3280= 32VDC, 120VAC
RIB3280U347= 32VDC, 347VAC
RIB4880= 48VDC, 120VAC
RIB4880U347= 48VDC, 347VAC
RIB12080= 120VDC, 120VAC
RIB12080U347= 120VDC, 347VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Features
• All RIB Series are fully load tested
prior to shipment
• Inverter is 100% solid state, short and
open circuit proof
• Polarized DC input (FPS Series only)
• 120VAC 60Hz input is standard, 277
and 347VAC available as options
• 25%, 50% or 80% lamp lumen output
• Mounts directly in ballast channel,
remote or optional T-Bar fixture
• CSA listed
Dimensions
Dimensions are approximate and subject to change.
INTERNAL ENCLOSURE (BLACK)
T ENCLOSURE (factory white)
3-1/4”
[8.3 cm]
1-1/2”
[3.8 cm]
7-1/4” [18.4 cm]
Fluorescent Inverters
2-3/4”
[7 cm]
15-1/4” [38.7 cm]
R ENCLOSURE (white)
20-7/8” [53 cm]
4-5/8”
[11.7 cm]
23-3/4” [60.3 cm]
3” [7.6 cm]
rib Series
RIB Series: The electrical contractor shall supply and install Ready-Lite® FPS Series remote fluorescent
inverter ballasts for each fixture as shown on plans. The inverter shall operate on
VDC input for
minutes during a power failure. The fluorescent lamp shall be maintained at
% lumen
output for one lamp only. The inverter is to be connected to the remote battery unit as shown on plans
(battery unit to be selected according to voltage/wattage and duration required). The inverter shall be
capable of illuminating the fluorescent lamp even when it is burned out under normal AC operation.
RIB Series: The electrical contractor shall supply and install Ready-Lite® FEB Series fluorescent inverters for
each fixture as shown on plans. The FEB Series inverter shall operate for
minutes during a power
failure. The fluorescent lamp shall be maintained at
% of nominal lumen output. The FEB Series
inverter shall be capable of illuminating the fluorescent lamp even when it is out under normal AC operations.
.
1-1/2” [3.8 cm]
4-1/2” [11.4 cm]
9-5/8” [24.4 cm]
2-1/2”
[6.4 cm]
RIB enclosure (white) - internal
D.C. power consumption
series
output %
lumens
Watts
RIB-800
25
800
10
RIB-1600
50
1600
20
RIB-3200
80
2560
32
ordering information FPS series
series
RIB6= 6V
RIB12= 12V
RIB24= 24V
RIB32= 32V
RIB48= 48V
RIB120= 120V
lumens / (%) for 48” tube
voltage
25= 25% (800 lumens) lumen outputs based on averages
50= 50% (1600 lumens) 24”/20W=1260 48”/40W=3200 96”/75W=6300
80= 80% (2560 lumens) inverters will operate T12, T8, or “U” type lamps
Blank= 120VAC
U277= 277VAC
U347= 347VAC
E XAMPL E : R I B 6 2 5
ordering information FEB series
Series
FEB
lumens / (%) for 48” tube
min. runtime
housing
ac voltage
25= 25% (800 lumens) lumen outputs based on
averages
50= 50% (1600 lumens)
24”/20W=1260 48”/40W=3200
96”/75W=6300
80= 80% (2560 lumens) inverters will operate T12,
T8, or “U” type lamps
-30= 30 minutes
-60= 60 minutes
-90= 90 minutes
-120= 120
minutes*
Blank= internal*
R= remote
mounting
enclosure
T= T-Bar
Blank= 120VAC
U277= 277VAC
U347= 347VAC
*FEB80 in T-Bar
cabinet only.
*Not available for
FEB80.
E XAMPL E : feb 5 0 - 9 0 R
138
Ammeter
Used to measure the current being supplied to the battery while in charge
mode.
AD
Auto-Diagnostics,
audible
Automatically tests and continuously monitors your emergency lighting unit. If
a problem occurs, the unit will send a visual (flashing or blinking LED indicator)
and audible warning. Complies with Fire Code requirements.
ADN
Auto-Diagnostics,
non-audible
Automatically tests and continuously monitors your emergency lighting unit. If
a problem occurs, the unit will send a visual (flashing or blinking LED indicator)
warning. Complies with Fire Code requirements.
Cab-tire
Unit supplied with a cab-tire cable used for special hardwire applications.
CW1
Cold weather,
120VAC
120VAC input cold weather protection feature for applications where
temperatures can reach -40° C.
CW3
Cold weather,
347VAC
347VAC input cold weather protection feature for applications where
temperatures can reach -40° C.
Time delay
Same as the D3 option but can be programmed for 5, 10, 15 or 20 minutes
delay.
D3
15 minutes time
delay
Normally, when the A.C. is restored, all emergency lighting lamps are turned
off. However, in some cases such as when metal halide lamps are used, it is
possible that the general lighting will not be available for several minutes after
the blackout (or brownout) period. Battery units with the D3 option will keep
some energy in store to ensure that the emergency lighting stays on or comes
back on for at least 15 minutes once the regular A.C. power has been restored.
D6
6cct. Fuse panel
Panel used to facilitate the connection of multiple input load circuits in high
power battery units.
H
Heater &
thermostat
Like a heat blanket, used to keep internal temperature optimal for battery units
that are installed in cold environments.
it
AC terminal block
Used to facilitate the connection of large gauge A.C. input cables.
LB
Light activated
test switch
Used to remotely test battery units by pointing a flashlight at a photocell
mounted on the bottom of a battery unit.
LC
Line cord (120V)
When ordering a battery unit with the LC option, we supply and pre-install a line
cord with a standard 3 prong 120V plug. Just hang the fixture and plug it in to a
standard receptacle! Only available on 120V units.
LD
Lamp disconnect
To disconnect the emergency lighting load in an area that is not in use during a
prolonged power failure or while the area is no longer being occupied.
NEX
NEXUS® wired
system interface
The NEXUS® system interface is a computerized maintenance system for
emergency lighting that, once programmed, will perform the tests, keep written
records and send notification if anything needs to be fixed. One full system
can address hundreds of units in as many buildings as you need from a single
location.
NEXRF
NEXUS wireless
system interface
The NEXUS® wireless system interface is a computerized maintenance system
for emergency lighting that, once programmed, will perform the tests, keep
written records and send notification if anything needs to be fixed. One full
system can address hundreds of units in as many buildings as you need from a
single location.
ot
DC terminal block
Used to facilitate the connection of large gauge D.C. output cables.
R3
Remote test
receiver
Used to perform maintenance tests by means of radio receiver in conjunction
with a transmitter (R4 option) on battery units that are out of reach. Simply
point the transmitter at the unit
R4
Remote test
transmitter
Used to perform maintenance tests by means of radio transmitter along with a
radio receiver (R3 option) on battery units that are out of reach.
TC
Teflon coated lens
A protective teflon coating that is applied to the glass lens of a lighting fixture to
prevent broken shards from falling in the event the glass is accidently broken or
vandalised.
tl
Twistlock plug
Used to facilitate the connection and removal of battery units for maintenance
purposes.
Tamper-proof
screws
Screws that require a special bit. Can be used on certain units to deny access to
unauthorized personnel.
Voltmeter
Indicates voltage being supplied to the battery when in charge mode.
A
CT
D
TP
V
®
139
THE
battery
GLOSSARY
Remote Heads represent a key
element of an emergency lighting
system performance. During a power
failure, these lamp heads must provide
adequate lighting levels for the safe
evacuation of the buildings.
overview
P. 144-145
Guardian™
P. 152
VQ
CADILITE®
P. 146-147
RF105
P. 153
RL25
n
RCSR
P. 148
RT/RQ/RM
P. 154
Tuf-NM
P. 158
P. 159
P. 160-161
RFX
Lamp chart
glossary
P. 165
P. 166-168
n
RL40M
Invisilite™
mini Invisilite™
LT/LQ/LS
legend™
legend™ RLR
WT
WSR & WHR
P.149
P. 155
n
P.162
n
P. 150
P. 156
P. 163
P. 169
n = new product
143
P. 151
P. 157
NMhz
P. 164
table
of
contents
EMERGENCY LIGHTING HEADS: PERFORMANCE & TECHNOLOGY
remote
fixtures
overview
Emergency Lighting Heads represent a key element of an emergency lighting system performance.
During a power failure, these lamp heads must provide adequate lighting levels for safe evacuation.
What level of illumination is necessary to ensure safe evacuation? Minimum levels are established
by the National Building Code of Canada:
3.2.7.3. Emergency Lighting
1 - Emergency lighting shall be provided to an average level of illumination not less than 10 lx at
floor or tread level
2 - Emergency lighting to provide an average level of illumination of not less than 10 lx at floor or
catwalk level shall be included in a service space referred to in Sentence 3.2.1.1.7).
3-T
he minimum value of the illumination required by Sentences (1) and (2) shall not be less
than 1 lx.”
You have probably already noticed the short lamp life of these light sources. Who would be
interested in using a bulb that only lasts 50 hours? The answer is simple: such a lamp produces
25% to 30% more light than a lamp of the same wattage but longer lamp life (i.e. 1,000 hours).
By design, the filament in an emergency lighting head is used at higher temperatures, increasing
light output. During a power failure, the emergency power supply is provided to the heads from
batteries. Equipment manufacturers and customers should use high intensity light sources, with
efficient light levels and distributions.
MINIATURE LAMPS: TUNGSTEN AND QUARTZ HALOGEN
Most commonly used emergency lighting heads are fabricated of an injection-molded thermoplastic housing containing a miniature lamp,
a metallic reflector and a polycarbonate lens. Lamps use a tungsten filament enclosed in a filling gas mixture of argon and nitrogen and are
generally referred to as incandescent lamps. Better performance is obtained with quartz halogen lamps, which are still incandescent lamps,
but the filling gas (iodide/chloride) allows the tungsten filament to operate at higher temperatures. This results in higher luminous intensity,
20 to 30% superior to standard incandescent lamps of the same wattage and lamp life. However, using high temperatures also increases
vaporization of the filament which shortens its life. As power failures are relatively scarce (let’s say 4 to 6 per year) and duration of emergency
lighting between 30 minutes to 2 hours, lamp heads are only used between 3 to 12 hours per year. A lamp with an average life of 50 hours
should therefore be functional for over four years. Lamp manufacturers offer two types of miniature lamps: long life and high light output.
PAR36 SEALED BEAM LAMPS
MR16 GENERATION
Emergency head performance also depends on lamp optics: the
reflector and the lens. This is especially critical in damp areas
where vapors and water condensation can deteriorate the electrical
contacts and the reflector performance. Sealed beam lamps are
recommended for such applications. Sealed beam lamp construction includes a metal coated glass reflector and a lens, designed to
provide a light beam of a certain opening: narrow, medium, large,
etc. The most common lamps used are those with a 4.5’’ diameter
(PAR36), available in both incandescent and halogen versions. As
to miniature lamps, there are sealed beam lamps dedicated to long
life applications (4,000 hours, 7-8 lumens/Watt) and for emergency
lighting (50 to 300 hours, 12-20 lumens/Watt). Originally, lamp life
wasn’t an issue. However, this has become increasingly important
in recent years, with the introduction of sophisticated emergency
lighting fixtures with periodic self-test and self-diagnostic features.
Such a system includes a micro-controller board that automatically simulates a power failure and forces the fixture in emergency
lighting mode every 30 days for at least 30 seconds and tests both
the batteries and the lamps. Even if the duration of the self-test is
minimal compared to the lamp life, the repetitive connection and
disconnection cycle of the lamps increases the risk of a premature
failure caused by the initial high current applied.
Fortunately, the lamp life issue was resolved with a new generation
of lamps that use MR16 technology (MR16 stands for Multi-facetted Reflector, 16/8’’ diameter). Increasingly popular, the MR16
contains everything in one: miniature halogen lamp, metal coated
glass reflector and, for the most part, a glass lens cemented to the
reflector. Easy to install, MR16 lamps are popular in both residential and commercial applications, and increasingly specified for
emergency lighting. In addition to their bright directional beam, these
lamps offer good efficacy (11 to 18 lumens/Watt), as well as long
life (2,000 to 6,000 hrs). First, the use of a glass lens which is clear
and thin, allows the MR16 to absorb much less light than a standard
diffuser lens; and second, efficient light distribution is accomplished
by the multi-facetted reflector.
144
remote
fixtures
overview
Standard wedge-base 9W Incandescent Lamp
Standard Emergency Lighting Units with 9W wedge-base incandescent lamps
200 to 220 Lumen 4W MR16 LED
Leading the technology trend, Ready-Lite® offers a complete series of
4W MR16 LED lamps available for all the standard battery voltages:
6V, 12V, 24V and 120V. With up to 30,000 hours of operational life
and a luminous flux of typically 220 lumens, they are available with
most emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one pair of
LED emergency heads installed at a height of 7.5ft, illuminates a
6ft by 40ft path of egress. Compared to halogen lamps (16-20W),
these 4W MR16 LED lamps illuminate the same area of egress during
an emergency situation by using 75% less power. This has a direct
impact on the battery size, reducing the back-up capacity needs
by 75%. Consequently, it also reduces the total cost of the application, with the use of smaller battery capacity units, the possibility of
using fewer fixtures due to superior illumination, thus also reducing
electrical wiring, and it reduces the environmental footprint.
4W MR16 LED lamps
Same Standard Emergency Lighting Units with 4W MR16 LED Lamps
LAMP SUFFIX
LD1
VOLTAGE
WATTAGE
6
4
LUMENS
200
REPLACEMENT #
580.0097-RL
LD7
12
4
220
580.0093-RL
LD13
24
4
220
580.0098-RL
5W MR16 LED lamp
new! 6W MR16 LED lamps
Same Standard Emergency Lighting Units with 5W MR16 LED Lamps
Same Standard Emergency Lighting Units with 6W MR16 LED Lamps
LAMP SUFFIX
LD9
VOLTAGE
12
WATTAGE
5
LUMENS
340
LAMP SUFFIX
REPLACEMENT #
LD10
580.0104-RL
VOLTAGE
12
WATTAGE
6
LUMENS
540
REPLACEMENT #
580.0106-RL
340-Lumen 5W MR16 LED
540-Lumen 6W MR16 LED
Keeping pace with technology, in 2012 we introduced a 12V-5W
MR16 LED lamp. With a typical luminous flux of 340 lumens, this
lamp has the same lighting performance as a 20W high-output
halogen MR16. A twin emergency head installed at a height of 7.5ft
illuminates more than a 70ft path of egress.
New in Fall 2013, we intoduced a 12V - 6W MR16 LED lamp, which
offer typical luminous flux of 510 lumens. Like the lower wattage
MR16 LED lamps, this new lamp is specially designed for emergency
lighting. It offers the same lighting preformance as the 35W MR16. A
twin emergency head installed at a height of 7.5’ illuminates approximately 100’ path of egress.
145
Type:
new product
Project/Location:
Contractor:
Prepared By:
NEMA-3R
Date:
Model No.:
Made in Canada
Table a: spacing for average 1fC
cadilite® Series
Rugged, Versatile, Sophisticated
Features
• Four-LED light engine with redundant
connections
• Powder-coated Die-Cast aluminum
construction
• Clear Polycarbonate lens allows for
maximum lumen output
• Surface Wall Mount
• Certified to the CSA 22.2 No.141
• NEMA-3R Damp and Wet locations
• Operating temperature -40°C to + 50°C
Options
• Forward-throw light distribution
• Dual-mode: normal and
emergency LED lighting
• High-lumen output
• Photo-switch: dusk-to-dawn control of
normal lighting
• Infrared remote control (normal lighting)
Model Type
Mouting Height
standard
9’
wattage capacity
CENTre-TO-CENTre
SINGLE
6’ X 50’
6’ X 50’
with option -H
11’
6’ X 60’
6’ X 60’
3’ X 70’
with option -FT
12’
6’ X 40’
-
with option -FTH
15’
6’ X 50’
-
Indoor reflectance: 80/50/20 and 10-ft wide corridor.
Outdoor reflectance: 0/30/10
Note: The illumination level meets ALL the requirements of the National Building Code-Canada and the Life
Safety Code (NFPA 101):
1) Average of 1 foot-candle (10.7 lux) or more
2) Minimum at any point of 0.1 foot-candle (1.07 lux) or more
3) Maximum-to-minimum illumination uniformity ratio of 40:1 or less
POwer consumption
AC SPECS: 120/347VAC
normal lighting
model type
emergency lighting
Current (max) Power (max) Current (max)
Power (max)
6-12VDC
remote
Power (max)
AC, ACDC, DC
0.12/0.05 A
12W
0.12/0.05 A
12W
8W
AC, ACDC, DC -H
0.18/0.07 A
18W
0.18/0.07 A
18W
14W
2AC (120VAC only)
0.12 A
12W
0.12 A
12W
-
2AC-H (120VAC only)
0.18 A
18W
0.18 A
18W
-
*Note: Only unswitched AC input, normal lighting with photo-switch or remote control.
c a di l i t e ® fa mi ly
Cadilite® Battery P. 102-103
146
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
dimensions
Dimensions are approximate and subject to change.
3” [7.5 cm]
6-5/8” [16.8 cm]
cadilite® Series
3” [7.5 cm]
9-1/2” [24 cm]
Rugged, Versatile, Sophisticated
Window for photo-switch (optional)
wide beam
(standard)
forward throw
(optional)
10’
um
inim
1fc m
age
ver
1fc a
1fc m
20’
40’
1fc average
inim
50’
28’
um
6’
9’
6’
ordering information
Series
CAD= cadilite® LED
function: Remote fixtures (-40… +50°C)
AC= AC-only 120/347VAC
ACDC= AC/6-12VDC remote
DC= 6-12VDC remote fixture
2AC= AC-only two circuits: 120/120 or 277/277V
Colour
OW= off-white
BK= black
DB= dark bronze
PG= platinum grey
Options
­FT= forward throw lighting
­H= high lumen output (-40...30°C)
­P= photo-switch, normal lighting (models AC, ACDC only)
­RC= remote control - infrared (models AC, ACDC only)*
­U2= 277VAC 60Hz input
*TB-RC1-R= remote control keypad (sold separately)
EXAMPLE: CADACDCBK-FT
147
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
4-1/2” [11.43cm]
RCSR Series
Dedicated Indoor LED Remote
Features
• Fully adjustable LED glare-free lens
• 3.6V 1W long life LED light source,
6000K
• Injection-molded off-white
thermoplastic ABS housing
• Ceiling or wall mount installation
• To mount to any standard 4” junction
box
• To be used only with RCSB battery unit
• Comes standard with one (1) year
warranty
2-1/16” [5.238cm]
R SC fa mi ly
RSC Exit P. 54
RCSC Combo P. 55
RCSB Battery P. 117
ordering information
Series
RCSR
number of heads
D= 2
lamp type/wattage
Blank= 1W LED
E xample : R C S R D
148
color
Blank= off-white
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
typical specifications
Supply and install Ready-Lite® RL40M Series remote emergency lighting. These remote fixtures will consist
of either single or double lamp configurations as specified and include a UV resistant fire retardant
polycarbonate back plate and a clear heavy-duty UV resistant polycarbonate light cover. The remote fixture
shall be certified to CSA C22.2 No. 141. The head(s) shall be fully adjustable and be equipped with high
efficiency MR16 halogen or LED lamp(s) of _____ V, _____ W.
The remote unit shall be Ready-Lite® model:
.
wire guards
460.0029-RL
RL40M Series
Remote Fixture
wall mount
replacement lamps: MR16 RL40MP
ordering code
Lamp Type
voltage
580.0074-RL
MR16 flood
6V-6W
580.0079-RL
MR16 flood
6V-10W
580.0080-RL
MR16 flood
12V-12W
580.0070-RL
MR16 flood
24V-12W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
For the complete list, please see the lamp chart on pages 166 to 168
replacement lamps: MR16 RL40M
ordering code
Lamp Type
voltage
580.0068-RL
580.0077-RL
MR16 IR flood
MR16 flood
12V-20W
24V-20W
Features
• Quality illumination requires fewer
fixtures
• Clear polycarbonate UV and impact
resistant lens with optional
tamper-proof screws to prevent
tampering
• Easy lamp replacement
• CSA certified to C22.2 No. 141
• Modern design will blend into
surroundings
• Selection of Die-Cast or polycarbonate
back plate
• For indoor use only
Dimensions
Dimensions are approximate and subject to change.
3-3/4” [9.5 cm]
4-5/8” [11.7 cm]
7-3/8” [18.1 cm]
ORDERING INFORMATION: Rl40MP
series
number of lamps
RL40MP= polycarbonate
back plate
lamp type/voltage/wattage
1= one lamp
2= two lamps
-LD1= MR16 LED, 6V-4W
-LD7= MR16 LED, 12V-4W
-LD9= MR16 LED, 12V-5W
-LD10= MR16 LED, 12V-6W
-LD13= MR16 LED, 24V-4W
-6/6= MR16, 6V-6W
-6/10= MR16, 6V-10W
-12/12= MR16, 12V-12W
-24/12= MR16, 24V-12W
colour
options
Blank= factory white
BK= black
GY= grey
Blank= no options
T= tamper-proof screws*
Other colours available
*690.0454-RL= tamper-proof bit (sold separately)
EXAMPLE: RL40MP1-6/6
ORDERING INFORMATION: RL40M
series
RL40M= die-cast
back plate
number of lamps
1= one lamp
2= two lamps
lamp type/voltage/wattage
-12/20= MR16IR, 12V-20W
-24/20= MR16, 24V-20W
EXAMPLE: RL40M1-12/20
149
colour
options
Blank= factory white
BK= black
GY= grey
Blank= no options
T= tamper-proof screws*
Other colours available
*690.0454-RL= tamper-proof bit (sold separately)
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
typical specifications
invisilite Series
™
Remote Fixture
Supply and install Ready-Lite® Invsilite™ Series of remote fixture: The unit shall be designed to be concealed
in walls or ceilings with a cavity. The unit equipment shall be completely concealed in the wall or ceiling
in the absence of remote power. Upon DC power supply the unit will rotate its door by 180° to expose
the emergency lamps, and power them. After the DC power disconnect the lamps will turn off and
the unit will conceal the heads by rotating the door by 180°. The DC-remote unit shall not require the
presence of AC power in order to open or close the door. Under normal conditions, the only visible parts
of the unit shall be the off-white flat door and trim plate that can be customized on site with paint or other
suitable wall covering. The light source shall be MR16 halogen or LED lamps of specified wattage and
light output.
The remote unit shall be the Ready-Lite® model:
.
Wire guards
Features
• Remote only visible upon power failure
• Front can be painted or wallpapered
on-site to match existing decor
• Fully automatic operation: The unit door
opens upon supply with DC voltage
from battery and closes after voltage
disconnect
• Time delay option required on battery
unit to properly close the door
• AC line voltage not required
• Emergency lights: Two high efficacy
MR16 halogen or MR16 LED lamps
• Certification: CSA C22.2 No.141
460.0082-RL
wall mount
replacement lamps: MR16
model
Lamp type
580.0080-RL
MR16 12W flood
voltage/wattage
12V-12W
580.0064-RL
MR16 20W flood
12V-20W
580.0083-RL
MR16 35W flood
12V-35W
580.0076-RL
MR16 50W flood
12V-50W
580.0068-RL
MR16 IR 20W flood
12V-20W high-output
580.0090-RL
MR16 IR 35W flood
12V-35W high-output
580.0089-RL
MR16 IR 50W flood
12V-50W high-output
580.0070-RL
MR16
24V-12W
580.0077-RL
MR16
24V-20W
580.0084-RL
MR16
24V-35W
580.0078-RL
MR16
24V-50W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
For the complete list, please see the lamp chart on pages 166 to 168
Dimensions
Dimensions are approximate and subject to change.
3-3/4” [9.6 cm]
DC VOLTAGE JUNCTION BOX
7-1/4” [18.3 cm]
7-1/4” [18.3 cm]
9-1/8” [23.1 cm]
ordering information
Series
HIDR= DC remote fixture
(no AC voltage required)
remote voltage
12= 12VDC remote*
24= 24VDC remote**
*The remote fixture is compatible with all Invisilite™
battery units
** 1
2V-24V battery unit must include the time delay
function and exclude diagnostic to close door:
consult factory for details.
lamp wattage
/LD7= 2X MR16 LED, 12V-4W
/LD9= 2X MR16 LED, 12V-5W
/LD10= 2X MR16 LED, 12V-6W
/LD13= 2X MR16 LED, 24V-4W
/12= 2X MR16 halogen, 12W
/20= 2X MR16 halogen, 20W
/35= 2X MR16 halogen, 35W
/50= 2X MR16 halogen, 50W
/20H= 2X MR16 halogen, high lumen output, 20W
/35H= 2X MR16 halogen, high lumen output, 35W
/50H= 2X MR16 halogen, high lumen output, 50W
EXAMPLE: H1DR12/12
150
options
TB= T-Bar mounting kit
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
typical specifications
Supply and install Ready-Lite® Mini Invsilite™ Series. The unit shall be designed to be completely concealed
in walls with a cavity. The equipment shall consist of a metal housing containing two modules joined by a
flexible bracket and electric conduit. One module contains the power transformer and electrical connection
box; the other module contains the emergency lights installed on the back of a door able to rotate several
turns of 360°. The unit equipment shall be completely concealed in the wall, after the installation through a
rectangular opening not larger than 8.25” by 5.75”.
In stand-by mode, the only visible parts of the unit shall be the off-white flat door and trim plate that can be
customized on site with paint or other suitable wall covering. Upon AC power supply the unit will expose the
emergency heads by rotating its door 180° and then will power the lamps. At the end of the AC power, the
lamps will turn off and the unit will retract the heads by rotating the door 180° in the same direction.
The unit shall not require the presence of AC power in order to close the door and conceal the lights. The door
of the unit shall be easy to force-turn (open or close) by hand. The light source shall be 12V MR16 halogen
lamps of specified wattage and light output.
The remote unit shall be the Ready-Lite model:
®
replacement lamps
model
type
voltage/wattage
580.0080-Rl
MR16 flood
12V-12W
580.0064-RL
MR16 flood
12V-20W
580.0083-RL
MR16 flood
12V-35W
580.0076-RL
MR16 flood
12V-50W
580.0068-RL
MR16 IR flood
12V-20W high output
580.0090-RL
MR16 IR flood
12V-35W high output
580.0089-RL
MR16 IR flood
12V-50W high output
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
mini invislite
Series
™
For AC Power Generator
Features
• Easy to retrofit in finished walls: the unit
slides in through an 8.25” by 5.75” hole
• No back-box needed to pre-install
• Output: 12VDC with up to 100W of
power
• Direct connection to 120, 277 or
347VAC power generators
• Emergency lights: MR16 halogen and
MR16 LED lamps
• Certification: CSA C22.2 No. 141
For the complete list, please see the lamp chart on pages 166 to 168
dimensions
Dimensions are approximate and subject to change.
3-1/2” [8.9cm]
complete unit
17-5/8” [44.9cm]
5-1/4” [13.2cm]
7” [17.8 cm]
9-1/8” [23.2cm]
installed unit
7-3/4” [19.7cm]
ordering information
Series
MH
unit capacity
G= remote AC generator, maximum 100W
lamp wattage (12V MR16)
/LD7= 2X MR16 LED, 12V-4W
/LD9= 2X MR16 LED, 12V-5W
/LD10= 2X MR16 LED, 12V-6W
/12W= 2X MR16 halogen, 12W
/20W= 2X MR16 halogen, 20W
/35W= 2X MR16 halogen, 35W
/50W= 2X MR16 halogen, 50W
/20WH= 2X MR16 halogen, high lumen output, 20W
/35WH= 2X MR16 halogen, high lumen output, 35W
/50WH= 2X MR16 halogen, high lumen output, 50W
EXAMPLE: MHG12W
151
AC voltage
Blank= 120VAC
2= 277VAC
3= 347VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
typical specifications
guardian™ Series
NEMA-3R
Wall Mounted, Remote Head
Wall mount unit shall be gasketed Die-Cast aluminum housing, impact resistant polycarbonate diffuser. The
lamps shall be adjustable for aisle or area distribution. Fixture shall be supplied with gasket and shall be
suitable for installation on any four inch octagonal box.
The remote unit shall be Ready-Lite® model:
.
Wire guards
460.0082-RL
wall mount
replacement lamps
model
Features
• Outdoor/Indoor installation
• Compact wall sconce unit for indoor
and outdoor use
• High impact resistant polycarbonate
diffuser
• Adjustabe lamps
• Die-Cast aluminum housing
• Vandal resistant option
• CSA Certified to C22.2 No. 141
lamp type
voltage/wattage
580.0079-RL
MR16 flood
6V-10W
580.0080-RL
MR16 flood
12V-12W
580.0064-RL
MR16 flood
12V-20W
580.0068-RL
MR16-IR flood
12V-20W
580.0070-RL
MR16 flood
24V-12W
580.0077-RL
MR16 flood
24V-20W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
Dimensions
Dimensions are approximate and subject to change.
5” [12.7 cm]
8” [20.4 cm]
7” [17.9 cm]
ordering information
Series
GUA= exterior remote
lamp type
Blank=(1) med. base socket only
(max. 60W) no lamp included
M= MR16
voltage/ wattage
Blank= no lamps
­LD1= 2X MR16 LED, 6V-4W
­LD7= 2X MR16 LED, 12V-4W
­LD9= 2X MR16 LED, 12V-5W
­LD10= 2X MR16 LED, 12V-6W
­LD13= 2X MR16 LED, 24V-4W
­6/10= 2X MR16 halogen, 6V-10W
­12/12= 2X MR16 halogen, 12V-12W
­12/20= 2X MR16 halogen, 12V-20W
­12/20H= 2X MR16, 12V-20W, high-output
­24/12= 2X MR16 halogen, 24V-12W
­24/20= 2X MR16 halogen, 24V-20W
colour
Blank= factory white
BK= black
DG= dark grey
BZ= dark bronze
options
C= clear lens
VR= vandal resistant screws*
*990.0119-RL= v andal resistant bit
(sold separately)
EXAMPLE: Gaum-LD10BK
152
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Wire guards
460.0033-RL
wall mount or ceiling mount
replacement lamps
model
lamp type
voltage/wattage
570.0016-RL
tungsten
6V-9W
570.0025-RL
tungsten
12V-9W
570.0045-RL
tungsten
24V-9W
Recess Mounted
rf105 Series
Compact Emergency Lighting
For the complete list, please see the lamp chart on pages 166 to 168
Features
dimensions
• Durable themoplastic trim (metal trim
as an option)
• PAR 36 Gimbal ring adjustable on two
planes to 45°
• Complete unit, no additional housing
needed
• Certified CSA C22.2 No.141
Dimensions are approximate and subject to change.
6-1/4” [15.87 cm]
ceiling opening
9” [22.86 cm]
5-1/2” [13.97 cm]
4-1/2” [11.43 cm]
Plaster
Frame
5-1/4” [13.33 cm]
Wire Box
Back Box
Trim
9” [22.86 cm]
8” [20.32 cm]
Gimbal Ring
ordering information
Series
RF105= PAR 36 recessed
lamp type
Blank= tungsten
Q= halogen
S= sealed beam tungsten
H= sealed beam halogen
housing
Blank= plastic trim
M= metal trim
voltage/wattage
6­ /9= tungsten, 6V - 9W, wedge base
­6/__= tungsten, 6V - 18 or 25W, D.C.B.
­12/__= tungsten, 12V - 9 or 18W, wedge base
­12/25= tungsten, 12V - 25W, D.C.B.
­24/__= tungsten, 24V - 9 or 18W, wedge base
­24/25= tungsten, 24V - 25W, D.C.B.
­6__= halogen, 6V - 8, 12 or 20W, bi-pin
­12/__= halogen, 12V - 8, 12, 20 or 55W, bi-pin
­24/__= halogen, 24V - 20 or 70W, bi-pin
­6/__= tungsten, 6V - 8, 12, 18 or 25W, sealed beam
­12/__= tungsten, 12V - 12, 18 or 25W, sealed beam
­6/__= halogen, 6V - 8, 12 or 20W, sealed beam
­12/__= halogen, 12V - 8, 12 or 37W, sealed beam
­32/__= tungsten, 32V - 18 or 25W, D.C.B.
­120/__= 120V - 10 or 15W, D.C.B.
­120/__= halogen, 120V - 35 or 50W, D.C.B.
Lamp 50W and above to use metal trim only.
NOTE : “___” insert wattage required.
EXAMPLE: RF105H-12/12
153
colour
Blank= factory white
B= black
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
typical specifications
Rt/rq/rm Series
Micro Tungsten Lamps,
Micro-Quartz Lamps, MR16
Lamps, or LED
Lamp head and stem shall be injection molded, impact resistant, flame retardant thermoplastic and shall
require no tool for aiming or adjustment. The lens shall be inverse concave design and fully adjustable for
aisle or area distribution during installation without the need to energize the lamp. Visual identification of
distribution shall be provided through position of adjustment pins.
Fixture shall be supplied with a canopy for installation on any four inch octagon box. Housing shall be designed
to allow for lamp replacement if required.
The remote unit shall be the Ready-Lite® model:
.
Wire guards
460.0029-RL
Features
• Available with tungsten, micro-quartz
MR16 or LED lamps
• Fire-retardant thermoplastic
o
• 300 rotation
• CSA certified to C22.2 No. 141
• 6, 12 and 24V with various wattages
wall mount or ceiling mount
replacement lamps
model
ac specs
570.0016-RL
tungsten
dc specs
6V-9W
570.0045-RL
tungsten
24V-9W
580.0015-RL
halogen
12V-12W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0098-RL
MR16, LED
24V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
For the complete list, please see the lamp chart on pages 166 to 168
Dimensions
Dimensions are approximate and subject to change.
3-3/16”
[8.2cm]
2-15/16”
[7.4cm]
5-9/16”
[14.2cm]
5”
[12.7cm]
3-3/16”
[8.1cm]
8-5/16”
[21.1cm]
4-13/16”
[12.3cm]
5”
[12.7cm]
ORDERING INFORMATION
series
RT= tungsten, wedge base
RQ= halogen, quartz bi-pin
RM= MR16 LED, halogen
number of lamps
1= single head
2= double head
3= triple head
voltage/wattage
­-LD1= MR16 LED, 6V-4W
­-LD7= MR16 LED, 12V-4W
­-LD9= MR16 LED, 12V-5W
­-LD10= MR16 LED, 12V-6W
­-LD13= MR16 LED, 24V-4W
­-6/6= MR16 halogen, 6V-6W
­-6/10= MR16 halogen, 6V-10W
­-12/12= MR16 halogen, 12V-12W
­-12/20= MR16 halogen, 12V-20W
­-24/12= MR16 halogen, 24V-12W
­-24/20= MR16 halogen, 24V-20W
­-6/9= 6V-9W, wedge base
­-12/9= 12V-9W, wedge base
­-12/18= 12V-18W, wedge base
­-24/9= 24V-9W, wedge base
­-24/18= 24V-18W, wedge base
­-6/8= halogen, 6V-8W, bi-pin
­-6/12= halogen, 6V-12W, bi-pin
­-12/8= halogen, 12V-8W, bi-pin
­-12/12= halogen, 12V-12W, bi-pin
EXAMPLE: RT1-6/9
154
colour
Blank= factory white
BK= black
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
typical specifications
Base and remote head are injection-molded thermoplastic, shockproof and flame retardant. Shall be supplied
factory white or black. The setting point shall provide visual indication of the light distribution. The fixture shall
be supplied with a canopy to be installed on any standard octagonal box. The housing shall be designed to
allow lamp replacement when required.
The remote unit shall be the Ready-Lite® model:
lt/lq/ls Series
Wire guards
460.0035-RL
wall mount single remote
460.0082-RL
wall mount double remote
460.0078-RL
wall mount triple remote
Surface Mounted, Remote Fixture
Features
replacement lamps
model
lamp type
voltage/wattage
570.0016-RL
mini tungsten, wedge base
6V-9W
570.0025-RL
mini tungsten, wedge base
12V-9W
580.0023-RL
mini halogen, bi-pin
24V-20W
• PAR 36, surface-mounted, large remote
fixtures
• Single, double or triple head
• Positive aim swivel
• CSA certified to C22.2 No. 141
dimensions
Dimensions are approximate and subject to change.
4-3/4” [12.06cm]
7-1/4” [18.41 cm]
3-5/8” [13.4 cm]
LQ
5” [12.7 cm]
3-5/4” [13 cm]
6-3/8” [17.27 cm]
10-7/8” [27.68 cm]
LS
5” [12.7 cm]
6-3/8” [17.27 cm]
12-3/8” [31.24 cm]
LT
9-1/2” [24.13 cm]
ORDERING INFORMATION
series
LT= tungsten, PAR 36
LQ= halogen, PAR 36
LS= tungsten, sealed beam
LH= halogen, sealed beam
# of heads
1= single
2= double
3= triple
voltage/wattage/lamp type
-­6/9= tungsten, 6V - 9W, wedge base
­-6/__= tungsten, 6V - 18 or 25W, D.C.B.
­-12/__= tungsten, 12V - 9 or 18W, wedge base
­-12/25= tungsten, 12V - 25W, D.C.B.
­-24/__= tungsten, 24V - 9 or 18W, wedge base
­-24/25= tungsten, 24V - 25W, D.C.B.
­-6/__= halogen, 6V - 8, 12 or 20W, bi-pin
­-12/__= halogen, 12V - 8, 12, 20 or 55W, bi-pin*
­-24/__= halogen, 24V - 20 or 70W, bi-pin**
­-6/__= tungsten, 6V - 8, 12, 18 or 25W, sealed beam
­-12/__= tungsten, 12V - 8, 12, 18 or 25W, sealed beam
­-6/__= halogen, 6V - 8, 12 or 20W, sealed beam
­-12/__= halogen, 12V - 8, 12 or 37W, sealed beam
­-32/__= tungsten, 32V - 18 or 25W, D.C.B.
­-120V_W= tungsten, 120V - 10 or 15W, D.C.B.
­-120/35= halogen, 120V - 35W, D.C.B.
­-120/50W= halogen, 120V - 50W, D.C.B*
Lamp 50W and above to use metal trim only.
NOTE : “___” insert wattage required.
E X A M P L E : LT 1 - 6 / 9
155
colour
Blank= factory white
BK= black
CH= chrome
M= factory white (metal)
option
TC= teflon coated lens
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
typical specifications
legend™ Series
Surface Designer Series
The contractor will supply and install Ready-Lite® Legend™ Series remote heads. These remote heads will consist
of either single, double or triple head configurations according to the design. Remote heads will be constructed
of durable powder coated, Die-Cast aluminum and use MR16 halogen light sources.
The remote fixtures shall be certified to CSA C22.2 No.250.
The unit shall be Ready-Lite® model: ___________________________________________________________.
wire guards
Features
• Contemporary, enduring design
• Available in 1, 2 or 3 head
configurations
• Highly resistant powder-coated,
Die-Cast aluminum construction
• MR16 halogen lamps: 6W, 10W, 12W,
20W, 35W and 50W MR16 LED lamps:
4W, 5W and 6W
• CSA certified to C22.2 No. 141
460.0029-RL
wall mount single remote
460.0032-Rl
wall mount double remote
460.0078-RL
wall mount triple remote
replacement lamps
model
lamp type
voltage-wattage
580.0074-RL
MR16 flood
6V-6W
580.0080-RL
MR16 flood
12V-12W
580.0077-RL
MR16 flood
24V-20W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
580.0095-RL
MR16, LED
120V-4W
For the complete list, please see the lamp chart on pages 166 to 168
dimensions
Dimensions are approximate and subject to change.
5” [12.7 cm]
9-5/8” [24.6 cm]
80o
320o
4” [10.2 cm]
4-1/8” [10.4 cm]
4-5/8” [11.7 cm]
5” [12.7 cm]
8” [20.3 cm]
RL150D
RL150
9-3/4” [24.9 cm]
RL150T
ORDERING INFORMATION
series
RL150= closed
# of heads
Blank= one head
D= two heads
T= three heads
colour
Blank= white
-B= black
lamp type/voltage/wattage
-­LD1= MR16 LED, 6V-4W
­-LD7= MR16 LED, 12V-4W
­-LD9= MR16 LED, 12V-5W
­-LD10= MR16 LED, 12V-6W
­-LD13= MR16 LED, 24V-4W
­-LD25= MR16 LED, 120V-4W
­-6/6= MR16 halogen, 6V-6W
­-6/10= MR16 halogen, 6V-10W
­-12/12= MR16 halogen, 12V-12W
­-12/20= MR16 halogen, 12V-20W
­-12/35= MR16 halogen, 12V-35W
­-12/50= MR16 halogen, 12V-50W
-24/12= MR16 halogen, 24V-12W
­-24/20= MR16 halogen, 24V-20W
­-24/35= MR16 halogen, 24V-35W
­-24/50= MR16 halogen, 24V-50W
-12/20H= MR16-IR, 12V-20W, high lumen output
-12/35H= MR16-IR, 12V-35W, high lumen output
-12/35H= MR16-IR, 12V-35W, high lumen output
­
EXAMPLE: RL150-6/6
156
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
The contractor will supply and install Ready-Lite® RLR Legend™ Collection recessed heads and housing.
Recessed heads will be constructed of durable powder coated metal and use MR16 halogen lamps. The
light source will be
V,
W MR16 halogen wide beam (flood) or otherwise specified.
The remote unit shall be Ready-Lite® model:
, housing shall be Ready-Lite® model:
.
replacement lamps
model
lamp type
voltage/wattage
580.0079-RL
MR16
6V-10W
580.0080-RL
MR16
12V-12W
580.0077-RL
MR16
24V-20W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
Recessed Designer Series
Features
• Contemporary, enduring designs
• 4W, 5W, 6W, 10W, 12W, 20W, 35W
and 50W lamps
• Wide beam MR16 (flood) or LED
light source
• Will blend in with regular decorative
recessed fixtures
• Choice of housing for new construction
or insulated ceiling
• RLR8NB and RLR8R are made of
powder coated or electro-plate steel
• RLR9 and RLR2 are made of Die-Cast
aluminum
For the complete list, please see the lamp chart on pages 166 to 168
housing
RL-GRHR03
non-insulated ceiling 6-24V
rlr legend™
Series
new construction
RL-GRHR04
non-insulated ceiling 6-24V
renovation
RL-GRHR05
non-insulated ceiling 120V GU10
new construction
RL-GRHR06
insulating ceiling 6-24V
new construction
MR16 LED Compatibility chart
head style
6V-4W
12V-4W
24V-4W
12V-5W
12V-6W
RLR8NB
x
x
x
-
-
RLR8R
x
x
x
x
x
RLR9
x
x
x
x
x
RLR2
-
-
-
-
-
RLR8NB
dimensions
Dimensions are approximate and subject to change.
4-1/2”[14.4 cm]
5/8"
5-5/8”5[14.3
cm]
143
5-5/8” [14.2 cm]
4” [10.2
cm]
INSULATED
CEILINGS
HOUSING
RL-GRH06 14-7/16” [36.7 cm]
RLR9
INSULATED CEILINGS HOUSING
RL-GRHR06
12-1/2” [31.72 cm]
7-1/4” [18.4 cm]
4-5/8” [11.74 cm]
6” [15.3 cm]
4” [10.2 cm]
7-3/4” [19.9 cm]
14” - 24” [35.6 - 60.9 cm]
RLR8R
non-INSULATED CEILINGS HOUSING
RL-GRHR05
Renovation HOUSING RL-GRHR04
3-1/2” [8.8 cm]
NEW CONSTRUCTION HOUSING
RL-GRHR03
RLR2
4” [10.2 cm]
11-1/4” [28.6 cm]
14” - 24” [35.6 - 60.9 cm]
ORDERING INFORMATION
series
RLR= decorative
recessed remote
head style
8NB= flat
8R= concave
9= concave
2= pop-out*
colour
lamp type/voltage/wattage
WH= white
BK= black (8R, 9 & 2 only)
BN= brushed nickel (8R, 8NB & 2 only)
CH= chrome (2 series only)
PB= polished brass (2 series only)
*Not availble
with LED and
GU10 lamps
EXAMPLE: RLR8NBWH-6/6
157
­LD1= MR16 LED, 6V-4W
­LD7= MR16 LED, 12V-4W
­LD9= MR16 LED, 12V-5W**
­LD10= MR16 LED, 12V-6W**
­LD13= MR16 LED, 24V-4W
­LD25= MR16 LED, 120V-4W**
­6/6= MR16 halogen, 6V-6W
­6/10= MR16 halogen, 6V-10W
­12/12= MR16 halogen, 12V-12W
­12/20= MR16 halogen, 12V-20W
­12/35= MR16 halogen, 12V-35W
­12/50= MR16 halogen, 12V-50W
­24/12= MR16 halogen, 24V-12W
­24/20= MR16 halogen, 24V-20W
­24/35= MR16 halogen, 24V-35W
­24/50= MR16 halogen, 24V-50W
­120/20= MR16, GU10, 120V-20W*
­120/35= MR16, GU10, 120V-35W*
­120/50= MR16, GU10, 120V-50W*
*Use RL-GRHR05 housing only.
**Not available with 8NB
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Remote heads VQ Series shall be comprised of one (single) or two (double or twin) 12W adjustable heads with
halogen lamps. Each lamp shall be housed in an impact-resistant polycarbonate cube. The cube lens shall be
frosted to diffuse the light. Heads shall provide mounting holes for installation on a standard octagonal box.
The remote unit shall be the Ready-Lite® model:
.
VQ Series
Wire guards
460.0029-RL
460.0032-RL
460.0031-RL
Surface Mount, Remote Fixture
wall mount (single cube)
wall mount (twin cube)
wall mount (double cube)
replacement lamps
Features
• Cubic, vandal-resistant
surface-mounted fixture
• Single, twin or double cube with
center body
• Frosted polycarbonate cube
• CSA certified to C22.2 No. 141
model
lamp type
voltage/wattage
570.0016-RL
580.0011-RL
mini tungsten, wedge base
mini halogen, bi-pin
6V-9W
6V-12W
580.0079-RL
MR16, flood
6V-10W
For the complete list, please see the lamp chart on pages 150 to 152
dimensions
VQ2
4-7/8” [12.4 cm]
5-7/8” [15.1 cm]
VQ1
4-3/4” [12.1 cm]
4-3/4” [12.1 cm]
Dimensions are approximate and subject to change.
14-3/4” [37.4 cm]
9-1/2” [24.1 cm]
VQW
4-3/4” [12.1 cm]
4-1/2” [11.3 cm]
5-7/8” [15.1 cm]
ORDERING INFORMATION
series
V= series
lamp style
T= tungsten
Q= halogen
M= MR16
halogen
# of heads
1= single cube
2= twin cube
W= double
cube
lamp style/wattage
-­ LD1= MR16 LED, 6V-4W
­-LD7= MR16 LED, 12V-4W
-­LD9= MR16 LED, 12V-5W
-­LD13= MR16 LED, 24V-4W
-­LD10= MR16 LED, 12V-6W
­-6/6= MR16 halogen, 6V-6W
­-6/10= MR16 halogen, 6V-10W
­-12/12= MR16 halogen, 12V-12W
­-12/20= MR16 halogen, 12V-20W
­-12/35= MR16 halogen, 12V-35W
­-12/50= MR16 halogen, 12V-50W
­-24/20= MR16 halogen, 24V-20W
­-24/35= MR16 halogen, 24V-35W
­-24/50= MR16 halogen, 24V-50W
-6/9= tungsten, 6V-9W, wedge base
­-12/9= tungsten, 12V-9W, wedge base
­-12/18= tungsten, 12V-18W, wedge base
-24/9= tungsten, 24V-9W,
wedge base
­­-24/18= tungsten, 24V-18W,
wedge base
-6/8= halogen, 6V-8W, bi-pin
­-6/12= halogen, 6V-12W, bi-pin
­-12/8= halogen, 12V-8W, bi-pin
­-12/12= halogen, 12V-12W, bi-pin
­-12/20= halogen, 12V-20W, bi-pin
­-24/20= halogen, 24V-20W, bi-pin­
-120/20= MR16, GU10, 120V-20W
­-120/35= M
R16, GU10, 120V-35W
EXAMPLE: VQ1-6/9
158
options
Blank= no options
TP= tamper-proof screws*
*690.0454-RL= tamper-proof bit
(sold separately)
colour
Blank= factory
white
BK= black
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
REPLACEMENT LAMPS
model
lamp type
580.0079-RL
MR16 flood
voltage-wattage
6V-10W
580.0080-RL
MR16 flood
12V-12W
580.0070-RL
MR16 flood
24V-12W
580.0104-RL
MR16, LED
12V-5W
For the complete list, please see the lamp chart on pages 166 to 168
Rl25 Series
Weatherproof Remote Fixture
dimensions
Dimensions are approximate and subject to change.
Features
• Quality illumination requires
fewer fixtures
• Weatherproof MR16 powder coated
cast aluminum light head
• Up to 24V-50W
• Available single or double head
• Pre-installed on a Red Dot®
weatherproof junction box:
- Five Outlets, 41⁄8” Diameter
- Copper-free aluminum provides
increased corrosion resistance
- Precision cast and machined
surfaces permit safer wire pulling
- Clean cover edges provide
good gasket sealing
- Precision NPT threads allow
trouble-free field installation for
rigid, IMC or EMT conduit
- Deep slotted stainless steel cover
screws for faster installation
• For use with 6V, 12V or 24V DC
MR16 or 12V-5W LED lamps
5” [12.7 cm]
4-7/8” [12.4 cm]
6-1/2” [16.5 cm]
4-1/8” [10.6 cm]
QTY = 2
9-1/8” [23.3 cm]
6-3/4” [17.3 cm]
4-1/8” [10.6 cm]
5-3/4” [14.7 cm]
17-1/4” [43.9 cm]
4-1/8” [10.6 cm]
ORDERING INFORMATION
series
RL25= weatherproof
remotes
# of heads
Blank= single head
D= double head
lamp voltage
-6= 6VDC
-12= 12VDC
-24= 24VDC
wattage
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
/6= MR16 halogen, 6V-6W
/10= MR16 halogen, 6V-10W
/12= MR16 halogen, 12, 24V-12W
/20= MR16 halogen, 12, 24V-20W
/35= MR16 halogen, 12, 24V-35W
/50= MR16 halogen, 12, 24V-50W
/20H= MR16-IR, 12V-20W, high output
/35H= MR16-IR, 12V-35W, high output
/50H= MR16-IR, 12V-50W, high output
EXAMPLE: RL25-12/20
159
colour
Blank= standard colour black head
grey junction box
Type:
new product
Project/Location:
Contractor:
Prepared By:
NEMA-4X
Date:
Model No.:
Made in Canada
typical specifications
TUF-NM Series
NEMA-4X
certified remote fixture
Supply and install Ready-Lite® TUF-NM Series remote emergency lighting fixtures. These remote fixtures will
consist of either single or double lamp configurations according to the design. These fixtures shall be fully
gasketed with a UV resistant and fire retardant polycarbonate back plate with a clear heavy-duty UV resistant
polycarbonate lens. The unit shall be equipped with two emergency heads with tool-less adjustable swivels.
Units shall be NEMA-4X and NSF certified and specifically designed for high abuse areas, wet and cold
weather locations, food processing plants, as well in applications requiring a resistance to corrosive agents.
The standard unit will come with stainless steel tamper-proof screws and bit. The remote fixture shall be
certified to CSA C22.2 No. 141. The head(s) shall be fully adjustable without tools and should be equipped
with MR16 halogen lamp(s) of
V
W.
The remote unit shall be the Ready-Lite® model:
.
n e m a - 4 x a n d n s f c e r t i f i e d fa mi ly
Features
• Fully gasketed with a selection of cast
aluminum or polycarbonate back plate
• Clear polycarbonate UV and impact
resistant lens
• Choice of single or double lamp models
• Available in 6, 12 and 24V models
MR16 or LED
• Easy lamp replacement
• Comes standard with tamper-proof
screws and bit
• NSF Certified for food processing plants
• NEMA-4X Certified*
• CSA Certified to C22.2 No. 141
• Suitable for indoor/outdoor installation
*For NMMP, units are NEMA-4X Certified when
installed using a circular NEMA-4X rated junction
box (sold separately by Thomas&Betts under P/N
CE365D-CAR or CE365DW-CAR and with plugs P/N
P7701W-CAR).
RNC Combo P. 64-65
RN P. 62
TUF P. 63
N-TUF Combo P. 66-67
TUF-NM Battery P. 128-129
wire guards
460.0029-RL
wall mount or ceiling mount
replacement lamps: MR16 TUF-NMMP
ordering code
Lamp Type
580.0074-RL
MR16 flood
voltage
6V-6W
580.0079-RL
MR16 flood
6V-10W
580.0080-RL
MR16 flood
12V-12W
580.0070-RL
MR16 flood
24V-12W
580.0097-RL
MR16, LED
6V-4W
580.0093-RL
MR16, LED
12V-4W
580.0104-RL
MR16, LED
12V-5W
580.0106-RL
MR16, LED
12V-6W
580.0098-RL
MR16, LED
24V-4W
replacement lamps: MR16 TUF-NMM
ordering code
Lamp Type
voltage
580.0068-RL
MR16 IR flood
12V-20WH
580.0077-RL
MR16 flood
24V-20W
160
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Dimensions
Dimensions are approximate and subject to change.
7-3/8” [18.1 cm]
TUF-NM Series
3-3/4” [9.5 cm]
4-5/8” [11.7 cm]
NEMA-4X
certified remote fixture
ORDERING INFORMATION: TUF-NMMP
series
NMMP= p
olycarbonate NEMA 4X
back plate
number of lamps
1= one lamp
2= two lamps
lamp type/voltage/wattage
­LD1= MR16 LED, 6V-4W
L­ D7= MR16 LED, 12V-4W
­LD9= MR16 LED, 12V-5W
­LD10= MR16 LED, 12V-6W
­LD13= MR16 LED, 24V-4W
­6/6= MR16 halogen, 6V-6W
­6/10= MR16 halogen, 6V-10W
­12/12= MR16 halogen, 12V-12W
­24/12= MR16 halogen, 24V-12W
colour
Blank= factory white
BK= black
GY= grey
options
-SM= surface mount*
*Surface plastic junction box
included.
EXAMPLE: NMMP1-6/6
ORDERING INFORMATION: TUF-NMM
series
NMM= die-cast NEMA 4X back plate
number of lamps
1= one lamp
2= two lamps
lamp type/voltage/wattage
­ 2/20H= MR16-IR, high output, 12V-20W
1
­24/20= MR16 halogen, 24V-20W
EXAMPLE: NMM1-12/20H
161
colour
Blank= factory white
BK= black
GY= grey
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
wire guards
wt Series
460.0082-RL
wall mount double remote
460.0078-RL
wall mount triple remote
model
lamp type
voltage-wattage
570.0016-RL
tungsten
6V-9W
570.0025-RL
tungsten
12V-9W
570.0045-RL
tungsten
24V-9W
For the complete list, please see the lamp chart on pages 166 to 168
dimensions
Dimensions are approximate and subject to change.
3-3/4” [9.5 cm]
4-3/4” [12.0 cm]
7-1/4” [18.3 cm]
• A
vailable in single, double
or triple head fixtures
• Durable thermoplastic construction
suitable for industrial or high abuse
areas
• Tool-less adjustment and aiming of
lamp heads
• Certified CSA C22.2 No.141
• Weatherproof
wall mount single remote
replacement lamps
Remote Fixture
Features
460.0035-RL
4-1/4” [10.7 cm]
12-1/2” [31.8 cm]
12-1/2” [31.8 cm]
5-1/2” [14.0 cm]
7-1/4” [18.3 cm]
3-3/4” [9.5 cm]
4-1/4” [10.7 cm]
4-1/4” [10.7 cm]
ORDERING INFORMATION
series
WT= tungsten, PAR 36
WQ= halogen, PAR 36
WH= halogen, sealed
beam
WS= tungsten, sealed
beam
# of heads
1= single
2= double
3= triple
voltage/wattage
-­6/9= tungsten, 6V - 9W, wedge base
­-6/__= tungsten, 6V - 18 or 25W, D.C.B.
­-12/__= tungsten, 12V - 9 or 18W, wedge base
­-12/25= tungsten, 12V - 25W, D.C.B.
­-24/__= tungsten, 24V - 9 or 18W, wedge base
­-24/25= tungsten, 24V - 25W, D.C.B.
­-6/__= halogen, 6V - 8, 12 or 20W, bi-pin
-­12/__= halogen, 12V - 8, 12, 20 or 55W, bi-pin
­-24/__= halogen, 24V - 20 or 70W, bi-pin
­-6/__= tungsten, 6V - 8, 12, 18 or 25W, sealed beam
-­12/__= tungsten, 12V - 12, 18 or 25W, sealed beam
­-6/__= halogen, 6V - 8 or 12 or 20W, sealed beam
­-12/__= halogen, 12V - 8, 12 or 37W, sealed beam
­-32/__= tungsten, 32V - 18 or 25W, D.C.B.
­-120/__= tungsten, 120V - 10, 15 or 30W, D.C.B.
­-120/__= halogen, 120V - 30 or 50W, D.C.B.
NOTE: “__”= insert wattage required.
EXAMPLE: WT2-6/9
162
colour
Blank= black
W= factory white
options
TC= teflon coated lens
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
replacement lamps
Model
Lamp Type
voltage-Wattage
550.0026-RL
tungsten
12V-12W
550.0027-RL
tungsten
12V-18W
550.0023-RL
tungsten
12V-25W
WSR & WHR Series
For the complete list, please see the lamp chart on pages 166 to 168
dimensions
Remote Fixture
Dimensions are approximate and subject to change.
WSR
SEALED BEAM
Features
12-7/8” [32.7 cm]
7-1/2” [18.9 cm]
5-5/8” [14.4 cm]
4-7/8” [12.2 cm]
• S
ealed beam, surface-mounted, rubber
coated industrial remote fixture
• For use in high pressure hose down
areas
• Available only in black
• Certified CSA C22.2 No.141
4-1/4” [10.7 cm]
4-1/4” [10.7 cm]
WHR
halogen quartz, h3
5-1/2” [14.1 cm]
7-3/4” [19.7 cm]
6” [15.2 cm]
13-1/2” [34.3 cm]
4-1/4” [10.7 cm]
4-1/4” [10.7 cm]
ORDERING INFORMATION
series
WSR
lamp type
1= single
2= double
voltage
options
­-6/__= tungsten, 6V - 8, 12, 18 or 25W, sealed beam
­-12/__= tungsten, 12V - 12, 18 or 25W, sealed beam
­-6/__= halogen, 6V - 8, 12 or 20W, sealed beam
­-12/__= halogen, 12V - 8, 12 or 37W, sealed beam
TC= teflon coated lens
* NOTE: “__”= insert wattage required.
EXAMPLE: WSR1-6/8
ORDERING INFORMATION
series
WHR= halogen
lamp type
voltage
1= single
2= double
­-12/55= halogen, 12V - 55W, H3
­-24/70= halogen, 24V - 70W, H3
* NOTE: “__”= insert wattage required.
EXAMPLE: WHR1-12/55
163
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
nmhz Series
Hazardous Location
Supply and install Ready-Lite® NMHZ Series remote emergency lighting fixture. The fixture shall have a singleor double-lamp configuration (as specified) and shall include a fully gasketed Die-Cast aluminum back plate
and a clear heavy-duty UV resistant polycarbonate cover. The fixture shall come standard with a 4” octagonal
box, stainless steel tamper-proof screws and dedicated screwdriver bit. The fixture shall be certified for use
in hazardous locations Class I, Division 2, Groups A, B, C and D and shall be listed to CSA C22.2 No. 141
and CSA C22.2 No.137-M1981. The fixture shall be rated with a temperature code for the selected lamps
as in the table below.
Each lamp in the fixture shall be able to be oriented without tools and should be equipped with MR16 halogen
lamp(s) of
V
W.
The remote unit shall be Ready-Lite® model:
.
h a z a rd o u s l o c at i o n fa mi ly c l a s s I , I I a n d I I I
Features
RH P. 68
TUFHZ P. 69
RHC Combo P. 70-71
HZ Combo P. 72-73
LDX-HZ Battery P. 130-131
replacement lamps
model
lamp type
voltage/wattage
temperature code
580.0079-RL
MR16 flood
6V-10W
T3B (max. 165oC)
580.0068-RL
MR16-IR flood (high output)
12V-20W-H
T2C (max. 230oC)
580.0077-RL
MR16 flood
24V-20W
T2C (max. 230oC)
580.0080-RL
MR16 flood
12V-12W
T3B (max. 165oC)
580.0070-RL
MR16 flood
24V-12W
T3B (max. 165oC)
580.0097-RL
MR16, LED
6V-4W
T4A (max. 120oC)
580.0093-RL
MR16, LED
12V-4W
T5 (max. 100oC)
580.0104-RL
MR16, LED
12V-5W
T4A (max. 120oC)
580.0106-RL
MR16, LED
12V-6W
T4 (max. 135oC)
580.0098-RL
MR16, LED
24V-4W
T5 (max. 100oC)
580.0095-RL
MR16, LED
120V-4W
T4A (max. 135oC)
dimensions
Dimensions are approximate and subject to change.
5-7/8” [14.9 cm]
7-1/8” [18.1 cm]
REMOTE
FIXTURE JUNCTION BOX
3-3/4” [9.5 cm]
2-1/8” [5.4 cm]
4-5/8” [11.7 cm]
• Quality illumination requires fewer
fixtures
• Certified Class I Zone 2, Groups IIA,
IIB and IIC
• Certified Class I Division 2, Groups A,
B, C and D as per CSA C22.2
No.137-M1981
• Temperature Codes: T3B (10W and
12W MR16 lamps) and T2C (20W
MR16 lamps), as per Canadian
Electrical Code, Part I and CSA C22.2
No.137-M1981)
• Extreme operational temperature range:
-40ºC to +40ºC.
• Choice of single- or double-lamp models
• High-efficacy MR16 halogen lamps
of 10W, 12W and 20W as well as
LED lamps of 4W, 5W and 6W
• Input voltage: 6V, 12V, 24V or 120V
• Fully gasketed Die-Cast aluminum back
plate
• Clear polycarbonate cover, UV and
impact resistant
• Easy installation on a 4” octagonal
box (included)
• Comes standard with tamper-proof
screws and bit
• Meets or exceeds CSA 22.2 No.141
ordering information
series
NMMHZ
number of lamps
voltage/wattage
1= one lamp
2= two lamps
­LD1= MR16 LED, 6V-4W
­LD7= MR16 LED, 12V-4W
­LD9= MR16 LED, 12V-5W
­LD10= MR16 LED, 12V-6W
­LD13= MR16 LED, 24V-4W
­LD25= MR16 LED, 120V-4W
­6/10= MR16, 6V-10W
­12/12= MR16, 12V-12W
­12/20= MR16, 12V-20W
­24/12= MR16, 24V-12W
­24/20= MR16, 24V-20W
­12/20H= MR16, high output, 12V-20W
EXAMPLE: NMHZ1-6/10
164
colour
GY= grey
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
Supply and install the Ready-Lite® RFX Series of hazardous location remote heads. The head housing will be
Die-Cast aluminum with grey epoxy powder coat finish. The lens shall be a clear, impact and heat resistant
prismatic glass globe. The head shall be factory sealed. External seals shall not be required. The remote shall
come complete with a _____ mounting connection and include _____lamp(s) rated _____ V ______ W. The
remote head shall be suitable for Class _____, Division _____, Group _____ .
The remote unit shall be Ready-Lite® model:
.
rfx Series
dimensions
Hazardous Location
Dimensions are approximate and subject to change.
15-1/4” [38.8 cm]
Severity S3, S4
10-3/4” [27.3cm]
1-7/8” [4.8cm]
9-5/8” [24.3cm]
3-5/8” [9.3cm]
17-7/8” [45.5cm]
9-1/8” [23 cm]
3” [7.7cm]
4” [10.1cm]
pendant mount
7” [17.8cm]
7” [17.8 cm]
7” [17.8 cm]
25-1/8” [63.7 cm]
1.
• CSA Certified for use in hazardous
locations:
- Class I, Divisions 1, Groups
A, B, C, D
- Class I, Divisions 2, Groups
A, B, C, D
- Class III, Divisions 1 and 2
• Die-Cast aluminum body with grey
epoxy powder coat finish
• Clear, impact and heat resistant
prismatic glass globe
• Available in 6, 12 and 24V & 120V
• Available with single-lamp or twin-lamp
combination
• New, easy-to-build catalogue number
based on the Ready-Lite® Severity
Codes
• Meets or exceeds CSA 22.2 No.141
26-3/4” [67.9cm]
7-1/4” [18.4cm]
13-5/8” [34.6cm]
7-1/4” [18.4cm]
9-1/8” [23cm]
7-1/4” [18.4cm]
25-1/4” [64 cm]
3-3/8” [8.4cm]
9-3/8” [23.8cm]
14-1/8” [35.9cm]
9-5/8” [24.5cm]
21” [53.3 cm]
7-1/8” [18.1cm]
11-5/8” [29.5cm]
5-1/4” [13.3cm]
Features
11-5/8” [29.5cm]
29-3/4” [75.6cm]
wall mount
6” [15.3cm] 6” [15.3cm]
ceiling mount
6” [15.3 m] 6” [15.3cm]
Severity S1, S2
2.
environment
severity code
Cl. I, Div. 1, Gr. A, B
S1
severity code
certification guide for remote lighting fixtures (40°C ambient)
S1
S2
S3
S4
Cl. I, Div. 1, Gr. C, D
S2
temperature code
T4A
T6
T1
T3C (E.G.F.)
CI. I, Div. 2, Gr. A, B, C, D
S3
CSA/UL rating
max. 120°C
max. 85°C
max. 450°C
max. 165°C
CL.II, Div.1 & 2, Gr. E, F, G
CL. III, Div. 1 & 2
S4
temperature codes
Severity Code Quartz bi-pin 12W, 20W
MR16 12V-12W
MR16 12V, 24V-20W
MR16 12V, 24V-35W
MR16 12V, 24V-50W
MR16 120V-20W
MR16 120V-35W
MR16 120V-50W
S1
T5 (100 C)
T6 (85 C)
T5 (100 C)
T4A (120 C)
T3C (160 C)
T5 (100 C)
T3A (180 C)
T3 (200oC)
S2
T5 (100oC)
T6 (85oC)
T5 (100oC)
T4A (120oC)
T3C (160oC)
T5 (100oC)
T3A (180oC)
T3 (200oC)
S3
T1 (450 C)
T4 (450 C)
T3 (200 C)
T2 (300 C)
T1 (450 C)
T2D (215 C)
T2 (300 C)
T1 (450oC)
S4
T4A (120 C)
(E,F,G)
T5 (100 C)
(E,F,G)
T5 (100 C)
(E,F,G)
T4A (120oC)(E,F,G)
T3C (160 C)
(E,F,G)
T4A (120 C)
(E,F,G)
T3C (160oC)(E,F,G)
N/A
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Ordering Information
series
Severity code
RFXQ= s ingle remote, one lamp
RFXQ1= s ingle remote, two lamps
RFXQ-P2= d
ouble remote, one lamp*
S1= CL.I, Div.1, Gr. A, B
S2= CL.I, Div.1, Gr.C, D
S3= CL.I, Div.2, Gr.A, B, C, D
S4= CL.II, Div.1 & 2, Gr. E, F, G
CL. III, Div. 1 & 2
*Pendant mount only.
voltage
-6/= 6V
-12/= 12V
-24/= 24V
-120/= 120V
lamp wattage/type
Blank= no lamp
12= 6V, 12V - 12W, quartz bi-pin
20= 6V to 24V-20W, quartz bi-pin
M12= MR16 halogen, 12V-12W,
M20= MR16 halogen,12V, 24V,120V-20W
M35= MR16 halogen,12V, 24V,120V-35W
M50= MR16 halogen,12V, 24V,120V-50W
MH20= MR16-IR 12V-20W, high-output
MH35= MR16-IR, 12V-35W, high-output
MH50= MR16-IR 12V-50W, high-output
EXAMPLE: RFXQS1-6/12C
165
mounting
C= ceiling mount
P= pendant mount
W= wall mount
Lamp chart
MR16 halogen lamps
lamp type
MR16 led
MR16
sealed beam
halogen lamps
sealed beam
incandescent lamps
xenon lamps
Typical spacing is based on a 6’ wide path and 80.50.20 reflectances
A= Typical spacing 7’ mounting 6’ wide
B= Typical spacing 15’ mounting 6’ wide
MR16 shape
PAR 36
PAR 36
T-3 1/4
part number
voltage
lumen
cadilite
RL40M
a
a
b
b
580.0074-RL
6V-6W
40
7’
1’
580.0079-RL
6V-10W
77
21’
20’
25’
17’
580.0080-RL
12V-12W
135
580.0075-RL
12V-20W
270
invisilite
a
31’
b
mini
Guardian
invisilite
a
b
X
X
19’
16’
-
36’
-
580.0064-RL
12V-20W
245
50’
36’
53’
39’
580.0068-RL
12V-20WH
417
65’
50’
70’
54’
580.0090-RL
12V-35WH
853
130’
110’
160’
171’
a
b
580.0089-RL
12V-50WH
1550
580.0083-RL
12V-35W
490
96’
86’
RL580.0076-RL
12V-50W
785
126’
100’
580.0077-RL
24V-20W
240
46’
37’
48’
38’
X
X
580.0070-RL
24V-12W
95
22’
13’
25’
15’
X
X
580.0084-RL
24V-35W
460
76’
60’
580.0078-RL
24V-50W
875
139’
12’
580.0065-RL
120V-20W
100
580.0066-RL
120V-35W
230
580.0067-RL
120V-50W
460
580.0097-RL
6V-4W
580.0093-RL
12V-4W
580.0104-RL
580.0106-RL
26’
17’
130
65’
23’
X
X
X
X
170
39’
23’
41’
25’
28’
-
12V-5W
340
71’
56’
71’
56’
71’
56’
12V-6W
510
41’
52’
52’
41’
X
X
580.0098-RL
24V-4W
200
580.0095-RL
120V-4W
200
100’
85’
85’
100’
100’
85’
550.0036-RL
6V-8W
155
550.0037-RL
6V-10W
190
550.0021-RL
6V-20W
380
550.0024-RL
12V-8W
130
550.0025-RL
12V-12W
240
550.0030-RL
6V-12W
225
550.0018-RL
6V-8W
130
550.0016-RL
6V-18W
270
550.0017-RL
6V-25W
400
550.0026-RL
12V-12W
190
550.0027-RL
12V-18W
210
550.0023-RL
12V-25W
395
570.0213-RL
6V-6W
120
17’
-
570.0214-RL
6V-10W
180
25’
18’
570.0215-RL
12V-6W
105
X
X
570.0216-RL
12V-10W
200
X
X
570.0211-RL
24V-12W
240
166
RF105
b
MR16 halogen lamps
a
b
legend
a
a
b
RLR
VQ
RL25
b
a
b
a
b
a
tuf-nm
b
a
wt
wsr/whr
b
a
b
a
b
nmhz
a
b
8’
3’
8’
3’
X
X
X
X
X
X
X
X
X
X
23’
22’
23’
22’
X
X
X
X
160’
171’
21’
20’
X
X
21’
20’
31’
19’
31’
19’
31’
19’
X
X
31’
19’
25’
17’
X
X
25’
17’
54’
41’
X
X
53’
39’
53’
39’
53’
39’
X
X
70’
54’
70’
54’
70’
54’
X
53’
39’
50’
36’
X
70’
54’
65’
50’
130’
110’
130’
110’
70’
54’
X
X
130’
110’
X
X
160’
171’
160’
171’
130’
110’
X
X
160’
171’
X
X
96’
86’
96’
86’
160’
171’
96’
86’
X
X
X
X
126’
100’
126’
100’
96’
86’
126’
100’
X
X
X
X
48’
38’
126’
100’
48’
38’
46’
37’
25’
15’
X
X
25’
15’
22’
13’
76’
60’
X
X
X
X
76’
60’
X
X
139’
12’
X
X
X
X
139’
112’
X
X
21’
20’
28’
19’
X
X
26’
17’
25’
MR16 led
sealed beam
halogen lamps
a
LT/LQ/LS
15’
X
42’
38’
X
X
X
X
65’
58’
X
X
X
X
38’
25’
38’
25’
38’
25’
X
X
X
X
41’
25’
41’
25’
41’
25’
X
X
X
X
71’
56’
X
X
100’
85’
71’
56’
71’
56’
71’
56’
71’
56’
52’
41’
52’
41’
52’
41’
X
X
43’
39’
100’
85’
100’
85’
100’
85’
100’
85’
Consult
your sales
representative
X
X
X
X
X
X
X
X
X
X
X
X
X
X
68’
55’
68’
55’
68’
55’
68’
55’
25’
18’
25’
18’
25’
18’
25’
18’
45’
37’
45’
37’
45’
37’
45’
37’
X
X
X
X
X
X
17’
14’
17’
14’
17’
14’
17’
14’
29’
18’
29’
18’
29’
18’
29’
18’
75’
48’
75’
48’
75’
48’
75’
48’
31’
23’
31’
23’
23’
23’
31’
23’
X
X
31’
19’
X
X
68’
43’
68’
43’
68’
43’
68’
43’
X
X
xenon lamps
sealed beam
incandescent lamps
RT/RQ/RM
167
rfx
a
b
Lamp chart
high intensity tungsten lamps
double contact bayonet base
lamp type
S8
bi-pin halogen lamps
RP-T1
incandescent lamps wedge base
T-2 1/4
H3
T-5
RT/RQ/RM
LT/LQ/LS
RF105
VQ
WT
wsr/whr
part
number
voltage
lumen
a
b
a
b
a
b
570.0040-RL
24V-18W
250
X
X
X
X
X
X
a
b
a
b
570.0037-RL
6V-18W
300
10’
-
10’
-
10’
-
570.0031-RL
12V-25W
400
X
X
X
X
X
X
570.0061-RL
24V-25W
400
X
X
X
X
X
X
570.0120-RL
120V-15W
94
X
X
16’
5’
X
X
X
X
X
X
X
X
X
X
X
X
X
X
570.0025-RL
12V-9W
138
570.0020-RL
6V-13W
188
X
X
570.0011-RL
12V-9W
126
570.0038-RL
6V-25W
400
570.0022-RL
12V-13W
188
X
X
X
X
X
X
570.0030-RL
12V-18W
276
X
X
X
X
X
X
570.0058-RL
24V-9W
75
X
X
X
X
X
X
580.0012-RL
6V-6W
113
X
X
X
X
X
X
580.0017-RL
6V-10W
200
X
X
X
X
X
X
580.0013-RL
6V-8W
163
23’
14’
17’
14’
17’
14’
17’
14’
23’
16’
15’
12’
580.0011-RL
6V-12W
240
580.0022-RL
6V-20W
400
X
X
15’
12’
15’
12’
23’
17’
23’
17’
X
X
17’
14’
a
b
RFX
a
b
15’
12’
X
X
23’
17’
X
X
580.0014-RL
12V-8W
163
24’
17’
16’
13’
16’
13’
16’
13’
16’
13’
580.0015-RL
12V-12W
276
X
X
20’
15’
20’
15’
20’
15’
20’
15’
X
X
580.0023-RL
24V-20W
133
21’
15’
21’
15’
21’
15’
21’
15’
X
X
580.0016-RL
12V-14W
300
X
X
X
X
X
X
580.0027-RL
12V-20W
314
34’
26’
34’
26’
34’
26’
X
X
78’
580.0030-RL
12V-55W
748
108’
580.0031-RL
24V-70W
791
104’
74’
570.0026-RL
6V-7.2W
100
X
X
X
34’
26’
X
X
X
X
X
X
X
570.0016-RL
6V-9W
150
12’
5’
12’
-
12’
-
12’
-
12’
-
570.0025-RL
12V-9W
138
14’
8’
18’
13’
18’
13’
18’
13’
18’
13’
570.0028-RL
12V-12W
150
X
X
X
X
X
X
X
X
570.0029-RL
12V-18W
264
24’
14’
18’
12’
18’
12’
18’
12’
18’
12’
570.0045-RL
24V-9W
113
12’
2’
15’
9’
15’
9’
9’
15’
15’
9’
570.0046-RL
24V-18W
240
21’
10’
21’
15’
21’
15’
15’
21’
21’
15’
570.0012-RL
6V-5.4W
68
X
X
X
X
X
X
X
A= Typical spacing 7’ mounting 6’ wide
B= Typical spacing 15’ mounting 6’ wide
Typical spacing is based on a 6’ wide path and 80.50.20 reflectances
168
104’
74’
108’
74’
TC
Teflon Coated
A protective teflon coating that is applied to the glass lens of a lighting fixture
to prevent broken shards from falling if the glass is accidently broken or
vandalized.
- For food processing environments
TP
Tamper-proof screws
Screws that require a special bit. Can be used on certain units to deny access to
unauthorized personnel.
- Bit ordered separately
169
the remote
glossary
There are a variety of ways in
which back-up power can be
provided. Central inverter systems
are specifically designed to provide
emergency power for emergency
lighting systems in a power failure.
RL-5
P. 174-175
IPS single phase IPS Three phase system options
RL4
P. 184-185
P. 176-177
P. 178-179
RL
central system
data request
P. 186-188
P. 180
interface
& display
P. 181
P. 189
n = new product
173
Mini Inverter
P. 182-183
n
table
of
contents
Choosing the right system
RL-5
A General Presentation about RL-5
Central Systems
Series highlights
Performance
The RL-5-Power Systems work with lighting
loads to provide full light output for
minimum 30 min. It is designed to support
incandescent, fluorescent and LED loads.
It will power these loads at cold starts for
all normally off circuits or normally on
circuits.
True Sine Waveform
Using a solid-state, pulse width modulation
(PWM) inverter, the systems produce pure
sinusoidal output waveform with less than
5% Total Harmonic Distortion (THD) for
linear loads.
There are a variety of ways in which back-up power can be provided. However, even though certain
methods are suitable for critical applications, they may not necessarily be suitable for Emergency Lighting.
This is because an Emergency Lighting system has unique load characteristics. And since Emergency
Lighting is a critical life-safety installation, it is vital that a Central Battery System is designed with these load
characteristics in mind. RL-5 Power central inverter systems are specifically designed to provide emergency
power for emergency lighting systems in a power failure.
In choosing the right AC system to support
emergency lighting it is important to consider the following
questions:
Overload performance
Is the system able to start the full load without the mains supply present. How does the system perform in a
total power failure (ie is the system able to start the load without the bypass supply being available)?
Repeat duty
CSA141-10 requires a central battery system to fully recharge within 24 hours. Is the charger able to
recharge the batteries quickly (80% in 14 hours or 100% after 24 hours)?
Energy consumption and heat dissipation
Are the inverter and charger permanently running, shortening the battery life, generating heat, wasting
energy and shortening component life? Are cooling fans running continuously, generating noise?
Maintenance
Is the system easy to service and maintain? Is the system designed in a modular format, or would the
failure of even a minor component require the whole system to be shut down and stripped for repair?.
Reliability
General information on UPS systems:
The product is third generation inverter
technology. LVD (Low Voltage Disconnect)
circuitry eliminates excessive battery drain
after long power outages.
Recharge period
Batteries
Automatic restart and recharge upon
restoration of utility.
Approvals
- CSA C22.2 No. 141-10 – Emergency
Lighting Equipment
- CSA C22.2 No. 107.3 – Uninterruptible
Power Systems
- UL 1778 – Uninterruptible Power
Systems
Applications
RL-5 -Power Systems can be used in
almost every type of building, especially
in architecturally sensitive applications
or when maintenance costs and testing
of individual unit equipment becomes
significant. Our systems are designed to
work with power factor corrected as well as
the most recent T5 and T5-HO electronic
ballasts.
UPS systems which are designed primarily for computer back-up generally offer short run times, 5 or 10
minutes. The long run times required for emergency lighting call for more powerful chargers to recharge
the larger bank of batteries needed in the time prescribed by CSA.
Overload performance
An emergency lighting load will impose large “in-rush” currents when starting lamps from cold. However,
UPS systems are often designed to shut down at only 125% overload and revert to the incoming supply.
During a total power failure situation, this could result in total failure of the emergency lighting system.
Furthermore, a UPS may fail to clear a breaker on a lighting circuit, meaning that a single short circuit fault
could result in loss of the entire emergency lighting supply.
Energy consumption and battery life
Most UPS systems operate in the “on-line” mode, whereby the inverter runs constantly to supply the load,
and power is taken from the battery with the charger running constantly. This places an excessive ripple
on the battery (contrary to the advice given by most battery manufacturers). Also, the system is constantly
generating heat which has a further detrimental effect on battery life. There are energy costs and heat
generation issues must be addressed when running an on-line system.
174
System design
The RL-5 Power inverter and charger modules utilize solid state electronics of the highest reliability to
provide a rugged, easy to maintain system with exceptional performance for emergency lighting use. The
system has been designed solely for emergency lighting, and not modified from other less essential power
supply requirements. As such, the system has exceptional overload performance without the need to
over-specify the rating of the inverter to ensure faults can be cleared. Each module has input and output
protection and each module measures and limits its own current. Alarms and status indications are
provided on the front panel display, which provide clear and concise information, rather than a long list of
parameters, which may be confusing.
Features
rl-5
A General Presentation about RL-5
Central Systems
Benefits
Self-Diagnostic/Self-Testing
Compliance with NFPA101
Programmable monthly and annual self-testing. Proven self-diagnostic
with information stored in separate memory logs for Test, Event and Alarm.
Microprocessor monitoring and control.
The self-testing meets the requirements of NFPA and UL. User programmable
time of testing. Test results, events or alarms can be downloaded from history
logs. Load monitoring. Reduced testing/service time.
Low heat dissipation
Less air-conditioning
Very low heat loss in standby operating mode (see specifications for exact
values). Convection cooling in normal mode with forced air during emergency
and recharge mode. Battery cabinets: convection cooling only.
Reduced costs for air-conditioning required to ensure the optimum operating
temperature when compared with equivalent systems that dissipate much more
heat. Higher reliability of fans and electronic components.
Versatile Installation
Easy to install
Modular design, easy front access freestanding cabinets, fasten together when
more than one cabinet is required. Optional seismic kit available. All wiring
provided is pre-cut and terminated, along with the necessary hardware for proper
installation.
Quick installation and connection through flexible cable entries and fast access
terminal blocks. Low MTTR (<30 min.) due to modular design, quick disconnect
means and frontal access.
Complete Protection
Reduced damage risks
Battery circuit breakers are standard. Modular standard systems offer overload
capacity, short-circuit protection, current- limiting, low-battery disconnect and
brownout protection as standard.
The full protection of the system will eliminate damage created by external events
and will increase lifetime of the electronics and the batteries.
Thermal Performance
Increased MTBF
Bonded oversized heat sinks for maximum thermal performance. Cooling fans
are energized only in inverter and recharge modes.
Increased reliability and reduced preventative maintenance. No air filters needed.
Monitoring and Control
Easy maintenance
User friendly programmable interface with LCD display provides full metering
values, easy program and control functions and a wide range of visual and
audible alarms.
Diagnostics, troubleshooting, preventative maintenance and service are made
easier by using the front panel display or the history logs.
175
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
SYSTEM SPECIFICATIONS
General
IPS single
phase Series
Interruptible emergency lighting inverter
system 3KVA-15KVA
Design
Stand-by. PWM inverter type utilizing Power Mosfet technology with 500ms transfer time.
Control
Microprocessor controlled, 4 x 20-character display with touch pad controls & functions
Metering
Input & Output Voltage, Battery Voltage, Battery & Output Current, Output VA, Temperature
Communications
RS-485 MODBUS RTU Port (DB-9)
Electrical Input
Voltage
Input Frequency
Features
• PWM/Power Mosfet technology
• Self-testing/Self-diagnostic
• User programmable with password
protection
• User programmable variable time delay
• Optional 100% normally Off output
• RS485 MODBUS RTU communication
port
• Micro-processor controlled
• 30, 60, 90, 120 minutes run times
• Summary alarm form C dry contact
• Generator compatibility
• Electronic and magnetic ballast
compatible
• Automatic event, test and alarm log
• LCD display
• Maintenance free standard batteries
• Forced air cooling during emergency
and recharge mode only
• Off when on standby
120, 277, 347VAC 2-wire or 120/240VAC 3-wire, 1-phase, +10%/ -15%
60Hz
Electrical Output
Voltage
120, 277, 347VAC 2-wire or 120/240 3-wire, 1-phase
+/-2% for +/-25% load step change, +/-3% for a 50% load step change, recovery within 3
cycles
Dynamic Voltage
Harmonic Distortion
<5% THD for linear load
Output Frequency
60Hz +/- 2Hz during emergency mode
Load Power Factor
0.7 lag to 0.9 lead
Inverter Overload
120% continious, 150% for 1 minute and 200% for 10 seconds
Protection
Optional External Distribution Circuit Breaker
Crest Factor
3
Environmental Conditions
Storage/Transport
Operating
Temperature
32ºF to 104ºF (0ºC to 40ºC) without batteries 68ºF to 86ºF (20ºC to 30ºC) with batteries(1)
System operates safely from 32°F to 104°F (0°C to 40°C) but optimum operation is between 68°
F and 77°F (20°C to 25°C). Battery performance can be affected by temperature.
Altitude
Relative Humidity
<10,000 feet (above sea level) without de-rating
Audible Noise
45 dBA at 1m from surface in emergency mode
0 to 95% non-condensing
(1) - max. 3 months at 77°F-86°F (25°C-30°C)
Single Line Diagram
ELECTRICAL/MECHANICAL CHARACTERISTICS for 30 minutes back-up time
Max. input
IPS cabinet No. of Batt. cabinet
Total
Effic.
Heat loss
IPS
Batt.
Power
No. of dimensions
current (A)(1)
dimensions Cabinet cabinet Battery system
at full
in normal Batt. Batt.
batt.
weight
rating
batt.
weight
load
mode
VDC ADC
cab.(1)
weight weight kg
kg(1)
KVA/KW
(1)
120V 240V 277V 347V (BTU/hr)
W” H” D”
W” H” D”
kg(1)
%
(2)
kg(1) (empty)(1)
3.0
98%
42
21
18
14
546
120
34
10
30
71
27
NA
NA
NA
NA
240
NA
105
345
6.0
98%
67
33
29
23
546
120
68
20
30
71
27
NA
NA
NA
NA
290
NA
210
500
9.0
98%
92
46
40
32
546
120
101
10
30
71
27
NA
NA
NA
NA
340
NA
372
712
12.0
98%
117
58
51
40
546
120
135
20
30
77
27
1
30
77
27
390
140
550
1080
15.0
98%
142
71
61
49
546
120
168
20
30
77
27
1
30
77
27
440
140
550
1130
1- For 30 min. discharge time. For other discharge times, consult factory.
2- Batteries are installed in the IPS cabinet for 3 to 9.0KVA systems, for 30 minutes only.
176
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
CABINETS
Modular design, freestanding NEMA-1 steel cabinets powder coated for corrosion and scratch resistance.
Front access design through hinged lockable doors requires only 42” front, 2” back and side clearance and
12” top clearance without drip shield. Top conduit entry Gland Plate.
INVERTER
Using Power Mosfet/PWM technology the inverter converts DC voltage supplied by the batteries to AC voltage
of a precise stabilized amplitude and frequency, suitable for most sophisticated electrical equipment. True
sinusoidal output waveform with very low distortion (less than 5% for linear loads). Overload capability of
120% continuous, 150% for 1 minute and 200% for 10 seconds.
IPS single
phase Series
Interruptible emergency lighting inverter
system 3KVA-15KVA
CHARGER
Fully automatic, temperature compensated, charger recharges fully discharged batteries in maximum 24
hours at nominal AC input voltage. AC input current limiting and over-voltage protection included.
BATTERY
System is provided standard with 10 year, maintenance free, sealed valve regulated, lead calcium batteries.
30, 60, 90 & 120 min. standard discharge time at full load under normal operating temperature (20ºC to
25ºC). Low Voltage Disconnect protection included. No special ventilation required.
SUPERVISION
Automatic self tests consist of a 2-minute monthly, 1/3 discharge at 6 months and full annual discharge. The
front-mounted control panel includes, a 4-line 20-character LCD display with a keypad to control and monitor
the operation of the system. This allows the operator to easily “watch” system functions as they occur and
check on virtually any aspect of the system’s operation. Standard RS485 MODBUS RTU diagnostic interface
ALARMS
Battery High/Low, Low Voltage Disconnect, Battery Disconnect, Maintained Lamp Off, Charger Fail, Supply
From Battery, System Inhibit, Circuit Breaker Trip, Module Breaker Trip, Inverter Undervoltage, Inverter
Overvoltage, Output Overcurrent, Hi Temp, Over Temp, Unit in Bypass, Inverter Frequency Control Failed,
Processor Reset.
OPTIONAL FEATURES
External Output Circuit Breakers, Output Trip Alarms, Extended Battery Warranty, 12 Hours Fast Recharge,
External Maintenance Bypass Switch. Dripshield, Remote Summary Alarm Panel, Normally Off Output,
Anchor Mounting Kit, Dry Contact Relay.
FACTORY START-UP
Includes one additional year of warranty. See warranty conditions.
WARRANTY
(full limited warranty conditions available upon request)
Limited manufacturer warranty is one-year, parts and labour, for system electronics. Battery warranty is one
year full plus 9 years pro-rata for a total of 10 years, under normal operating conditions. System must be put
in service within 6 months from ship date in order to validate warranty. Consult factory for other battery types.
Ordering Information (1)
Series
System Voltage
KVA/KW
R= Series
1= 120-120 input-output
2= 120/240-120/240
(3 wire in-out)
3= 277-277
4= 347-347
A= 3
B= 6
C= 9
D= 12
E= 15*
* Other voltages available using
external transformer (sold
separately)
* For 120 minutes
run time, minimum
120/240VAC in/out
Run Time
3= 30 minutes
6= 60 minutes
9= 90 minutes
12= 120 minutes
External Circuit Breaker
B= no breakers
N####= normally on
F####= normally off
First two digits= Qty.
01 to 99 max (specify)
Last two digits= Amp rating
10, 15, 20, 25... (specify)
Options
A= fast recovery charge
C= remote summary alarm panel
E= output trip alarm
G= “inverter on” dry contact
H= normally off full capacity output
I= extended battery warranty*
J= external maintenance bypass
K= anchor mounting kit
L= drip shield
M= second output terminal block
N= normally on & normally off output**
* Consult your sales representative.
Example :N1020
E x a m ple : R 1 A 3 N 1 0 2 0
177
** Full capacity available on either output
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
SYSTEM SPECIFICATIONS
General
IPS three
phase Series
Design
Stand-by. PWM inverter type utilizing Power Mosfet technology with 500ms transfer time.
Control
Microprocessor controlled, 4 x 20-character display with touch pad controls & functions
Metering
Input & Output Voltage, Battery Voltage, Battery & Output Current, Output VA, Temperature
Communications
RS-485 MODBUS RTU Port (DB-9)
Electrical Input
Interruptible emergency lighting inverter
system 4.5KVA-54KVA
Voltage
120/208, 277/480, 347/600VAC 3-phase 4-wire +10% / -15%.
Input Frequency
60Hz
Electrical Output
Features
Voltage
120/208, 277/480, 347/600VAC 3-phase 4-wire.
• PWM/Power Mosfet technology
+/-2% for +/-25% load step change, +/-3% for a 50% load step change, recovery within 3 cycles
Dynamic Voltage
• Self-testing/Self-diagnostic
Harmonic Distortion <5% THD for linear load
• User programmable with password
protection
60Hz +/- 2Hz during emergency mode
Output Frequency
• User programmable variable time delay
0.7 lag to 0.9 lead
Load Power Factor
• Optional 100% normally Off output
120% continuous, 150% for 1 minute and 200% for 10 seconds
Inverter Overload
• RS485 MODBUS RTU communication
Optional External Distribution Circuit Breaker
Protection
port
• Micro-processor controlled
3
Crest Factor
• 30, 60, 90, 120 minutes run times
Environmental Conditions
• Summary alarm form C dry contact
32ºF to 104ºF (0ºC to 40ºC) without batteries 68ºF to 86ºF (20ºC to 30ºC) with batteries(1)
Storage/Transport
• Generator compatibility
• Electronic and magnetic ballast
Operating
System operates safely from 32°F to 104°F (0°C to 40°C) but optimum operation is between 68° F
compatible
and 77°F (20°C to 25°C). Battery performance can be affected by temperature.
Temperature
• Automatic event, test and alarm log
<10,000 feet (above sea level) without de-rating
Altitude
• LCD display For all fluorescent/incandescent/LED loads
0 to 95% non-condensing
Relative Humidity
• Maintenance free standard batteries
45 dBA at 1m from surface in emergency mode
Audible
Noise
• Forced air cooling during emergency
and recharge modes only
(1) - max. 3 months at 77°F-86°F (25°C-30°C)
• Off when on standby
ELECTRICAL/MECHANICAL CHARACTERISTICS for 30 minutes back-up time
Batt.
No.
Batt.
Max. input
Heat loss
No. of IPS cabinet No. of
Power Effic.
No. of
cabinet
of 30
cabinet
current (A)(1) in normal Batt. Batt.
IPS dimensions 20 batt.
rating at full
batt.
dimensions batt. dimensions
mode
VDC ADC
cab.
cab.(1)
KVA/KW load % 208/ 480/ 600/
(1)
cab.(1)
(BTU/hr)
(1)(2) W” H” D”
(2)
W” H” D”
W” H” D”
120V 277V 347V
(2)
Total IPS
Cabinet
weight
kg(1)(2)
4.5
98%
29
13
10
546
120
50
20
1
30 71 27
NA
NA NA NA
NA
NA NA NA
265
Total batt.
Total
Battery
cabinet
system
weight
weight kg
weight
kg(1)
(empty)(1)
kg(1)
NA
210
475
9.0
98%
42
18
14
546
120 101
10
1
30 71 27
NA
NA NA NA
NA
NA NA NA
340
NA
372
712
13.5
98%
54
23
19
546
120 151
20
1
30 77 27
1
30 77 27
NA
NA NA NA
415
140
550
1105
18.0
98%
67
29
23
546
120 202
20
1
30 77 27
1
30 77 27
NA
NA NA NA
540
140
744
1424
22.5
98%
79
34
27
546
120 252
30
1
30 77 27
NA
NA NA NA
1
30 71 30
615
165
825
1605
27.0
98%
92
40
32
546
120 303
30
1
30 77 27
NA
NA NA NA
1
30 77 30
690
165
1116
1971
31.5
98%
104 45
36
1092
120 353
30
2
30 77 27
1
30 77 27
NA
NA NA NA
905
140
1116
2161
36.0
98%
117 51
40
1092
120 403
40
2
30 77 27
NA
NA NA NA
1
30 77 30
1030
165
1488
2683
40.5
98%
129 56
45
1092
120 454
40
2
30 77 27
2
30 77 27
NA
NA NA NA
1105
280
1488
2873
45.0
98%
142 61
49
1092
120 504
50
2
30 77 27
1
30 77 27
1
30 77 30
1180
305
1860
3345
49.5
98%
NA 67
53
1092
120 555
50
2
30 77 27
1
30 77 27
1
30 77 30
1255
305
1860
3420
54.0
98%
NA 73
58
1092
120 605
60
2
30 77 27
NA
NA NA NA
2
30 77 30
1380
330
2232
3942
1- For 30 min. discharge time. For other discharge times, consult factory.
2- Batteries are installed in the IPS cabinet for 4.5 to 9.0KVA systems, for 30 minutes only.
178
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Single Line Diagram
IPS three
phase Series
Interruptible emergency lighting inverter
system 4.5KVA-54KVA
CABINETS
Modular design, freestanding NEMA-1 steel cabinets powder coated for corrosion and scratch resistance. Front access
design through hinged lockable doors requires only 42” front, 2” back and side clearance and 12” top clearance without
drip shield. Top conduit entry Gland Plate.
INVERTER
Using Power Mosfet/PWM technology the inverter converts DC voltage supplied by the batteries to AC voltage of a precise
stabilized amplitude and frequency, suitable for most sophisticated electrical equipment. True sinusoidal output waveform
with very low distortion (less than 5% for linear loads). Overload capability of 120% continuous, 150% for 1 minute and
200% for 10 seconds.
CHARGER
Fully automatic, temperature compensated, charger recharges fully discharged batteries in maximum 24 hours at nominal
AC input voltage. AC input current limiting and over-voltage protection included.
BATTERY
System is provided standard with 10 year, maintenance free, sealed valve regulated, lead calcium batteries. 30, 60, 90 &
120 min. standard discharge time at full load under normal operating temperature (20ºC to 25ºC). Low Voltage Disconnect
protection included. No special ventilation required.
SUPERVISION
Automatic self tests consist of a 2-minute monthly, 1/3 discharge at 6 months and full annual discharge. The frontmounted control panel includes, a 4-line 20-character LCD display with a keypad to control and monitor the operation of
the system. This allows the operator to easily “watch” system functions as they occur and check on virtually any aspect of
the system’s operation. Standard RS485 MODBUS RTU diagnostic interface
ALARMS
Battery High/Low, Low Voltage Disconnect, Battery Disconnect, Maintained Lamp Off, Charger Fail, Supply From Battery,
System Inhibit, Circuit Breaker Trip, Module Breaker Trip, Inverter Undervoltage, Inverter Overvoltage, Output Overcurrent,
Hi Temp, Over Temp, Unit in Bypass, Inverter Frequency Control Failed, Processor Reset.
OPTIONAL FEATURES
External Output Circuit Breakers, Output Trip Alarms, Extended Battery Warranty, 12 Hours Fast Recharge, External Maintenance Bypass Switch. Dripshield, Remote Summary Alarm Panel, Normally Off Output, Anchor Mounting Kit,
Dry Contact Relay.
FACTORY START-UP
Includes one additional year of warranty. See warranty conditions.
WARRANTY
(Full limited warranty conditions available upon request)
Limited manufacturer warranty is one-year, parts and labour, for system electronics. Battery warranty is one year full plus
9 years pro-rata for a total of 10 years, under normal operating conditions. System must be put in service within 6 months
from ship date in order to validate warranty. Consult factory for other battery types.
Ordering Information(1)
Series
System Voltage
RIII=
Series
1= 1
20/208 4
wire
2= 277/480
3= 347/600
Other voltages
available using
an external
transformer (sold
separately)
KVA/KW
A= 4.5
B= 9
C= 13.5
D= 18
E= 22.5
F= 27
G= 31.5
H= 36
I=40.5
J= 45**
K= 49.5*
L= 54*
*Min. 277/480Vac in/out
**For 120/208Vac in/
out,120 mins. runtime
not available.
Run Time
3= 30
minutes
6= 60
minutes
9= 90
minutes
12= 120
minutes
External Circuit Breaker
B= no breakers
N####= normally on
F####= normally off
First two digits= Qty.
01 to 99 max (specify)
Last two digits= Amp rating
10, 15, 20, 25... (specify)
Example: N1020
E x a m ple : R I I I 1 A 3 N 1 0 2 0
179
Options
A= fast recovery charge
C= remote alarm panel
E= output trip alarm
G= “inverter on” dry contact
H= normally off full capacity output
I= e xtended battery warranty*
J= e xternal maintenance bypass
K= anchor mounting kit
L= drip shield
M= s econd output terminal
block
N= normally on & normally
off output**
*Consult your sales
representative.
**Full capacity available on
either output
(-A) 12 Hour Fast Recharge
Battery charger upgrade option which decreases the time required to recharge a fully discharged battery to
a fully charged state. The normal 24 hour recharge time is reduced to a 12 hour period.
(-C) Remote Summary Alarm Panel
systems options
Details
Wall mountable box provides visual and audible alarms with silence switch. The panel consists of LED
indicators and built in audible alarm and may be located up to 1,000 feet away from the inverter system.
(-E) Output Trip Alarm
System triggers an alarm when any output breaker trips.
(-G) Inverter On Dry Contacts
Form C dry contacts that will change state when the system transfers to battery.
(-H) Normally Off Output
This output circuit is dedicated for the emergency only equipment. Emergency only equipment operates
during power outages and when the system is on battery back up. This option leaves the normally off load
circuits off during normal utility power conditions.
(-I) Extended Battery Warranty
Extends battery warranty from 10 years pro-rated to 20 years pro-rated.
(-J) External Maintenance Bypass Switch
The external maintenance bypass switch is mounted in a maximum of 20”H x 16”W x 9”D NEMA 1
separate enclosure, used to completely isolate the inverter system from the connected load and AC utility
input. This option allows the system to be safely powered down for maintenance or service.
(-K) ANCHOR MOUNTING KIT
The anchor mounting kit option is designed to prevent system movement during seismic events. Heavy
duty brackets are provided to secure system cabinetry to your surfaces.
(-L) Drip Shield
Hood cover to protect the enclosure against falling water from sprinkler systems.
(-M) Second Output Terminal Block
The output of the Central System is divided into two. The load can be connected to either outputs.
(-N) Normally On & Normally Off Outputs
The Central System can have both normally on and normally off outputs. Either output can handle 100% of
the load.
180
Meter & Reading
Functions Menu
• AC Voltage Output
• AC Current Ouput
Normally On
• AC Current Output
Normally Off
• Battery Voltage
• Battery Charging Current
• Battery Discharging Current
• KVA Total Output
• Cabinet Internal Temperature
• Inverter Frequency
• Real Time Clock
• Time Delay
• Monthly Test Result
• Half Year Test Result
• Annual Test Result
• Event Log Reading
Administration
Menu Functions
• Passkeyword protected
• Read/Set Serial Number
• Read/Set
Manufacturing Date
• Read/Set Installation Date
• Read Firmware Version
• Read/Clear Battery
Elapse Time
• Read/Clear Total
Power Failures
• Read/Clear Total Alarms
• Clear Event Log
• Enter Calibration Routine
Service Menu
Functions
• Passkeyword protected
• Set Battery Voltage
& Current Ranges
• Set System Voltage
& Current Ranges
• Set System Phase
• Set Normally OFF Load
• Set Language
• Set Real Time Clock
& Calendar
• Set Time Delay Function
• Set Manual Test Duration
• Set Self Test Sequence
• Set Buzzer Function
Alarm and Events
• Event Logging (1000)
Type Date & Hour
• Transfer Mode
• Standby
• Load Off
• Stop Mode
• Lock-Out Mode
• Forced Transfer
• Battery Volt
• Battery Disconnect
• Mains Out Of Range
• Manual Test
• Monthly Test
• Half Year Test
• Yearly Test
• Modbus Transfer
181
User interface
& display
functions
System Testing
RL-5 Central Battery Systems provide
manual and automatic test functions.
Manual test can be activated any time
using the test key provided on the control
panel. Manual testing will do a programmable fixed test time and can be aborted
any time by pushing again on the test
key. Automatic test and diagnostic is done
following an annual sequence. Every
month a quick diagnostic test of 2 minutes
is performed. At the 6 month mark, a 1/3
timed discharge test is done, and at the
12 month, a full discharge, down to LVD is
performed. Pass/Fail and discharge time
are registered in the event log. Test time
and date is programmed using the Service
Menu.
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
The Mini-Inverter is a cUL Listed stand-alone pure sine wave output inverter designed to provide power to
designated emergency lighting fixtures. In a power loss situation, it will supply power from the onboard
battery supply.
mini-inverter
Series
Interruptible Unit Equipment
Features
• Lamps operated: Incandescent LED,
fluorescent lamps and ballast
combinations, including TRIAC dimmable
ballasts (consult your sales representative
for 0-10V or DALI dimming)
• Components: High-efficiency pure sine
wave inverter
• Temperature-compensated charger
12V oversized Valve Regulated
lead acid (VRLA) battery
• Construction: 14-gauge steel housing
• Emergency lighting supplied from one
convenient, reliable source
• Input/Output voltage 120/120V 60Hz or
347/347V 60 Hz
• Replaceable output fuse protection
• Valve Regulated Lead Acid (VRLA) battery
provides long-life and is maintenance free
• Line voltage allows remote mounting of
emergency fixtures; distances up to
1000 ft.
• Low Battery Voltage Disconnect
• Unit comes standard with electonic
lockout and brownout circuits
• Meets or exceeds all National Electrical
Code and Life Safety Code Emergency
Lighting Requirements
• Cabinet in factory white powder-coat
paint finish
• May accept load to it’s full capacity when
load feature power factor of 0.9 or more
• Non audible self-diagnostic is standard.
Nexus® system interface available with an
improved minimum lost detection of 10%
• Meets or exceeds the requirements of
CSA 141-10
The Mini-Inverter works in conjunction with incandescent, LED, and fluorescent fixture types and will
automatically run switched, normally-on, or normally-off designated emergency fixtures.
The Mini-Inverter is ideal for applications requiring an emergency source for lighting arrangements that utilize
multiple lamp and fixture types and is available in surface mount and comes with a one year warranty and
nine-year pro-rata battery warranty.
typical SPECIFICATIONS
Emergency lighting shall be provided by inverter unit equipment designed to operate designated incandescent, fluorescent and LED fixtures on emergency power at their full nominal lumen rating during the
full 30 minutes emergency discharge cycle. System output will be rated at _____ watts for 30 minutes and
provide fused output connections to the load. The system’s voltage rating shall be _____ VAC input/output.
The inverter unit shall allow for connected emergency fixture(s) to be normally on, normally off, switched or
dimmed without affecting lamp operation during a power failure.
Upon utility power loss, the inverter unit shall deliver 100% of its rated output to the emergency fixtures
regardless of the local switch or dimmer (TRIAC) position, and will provide power to emergency fixtures at
distances of up to 1000 feet. The housing shall be manufactured using 14-gauge steel with a white baked-on
powder coat paint finish.
The unit’s electronics shall include a self-contained inverter section with a fully automatic, thermal-compensating variable-rate battery charger, AC lockout feature, low battery voltage disconnect, overload, short
circuit and brownout protection as standard. The unit shall utilize a sealed lead acid battery with a 10-year
design life. The inverter system shall be UL 924 Listed and labeled. The unit shall be covered under a 1-year
warranty on the electronics and battery and a 9-year pro-rata warranty on the battery. It shall meet or exceed
the requirements
of CSA 141-10.
Specifications
TRANSFER TIME: less than 1 second
VOLTAGE REGULATION ON EMERGENCY: +/- 3%
FREQUENCY REGULATION ON EMERGENCY: 60 Hz +/- 1%
LOAD POWER FACTOR RANGE: 0.9 leading to 0.9 lagging
OPERATING TEMPERATURE: 20° TO 30°C (68° TO 86°F)
Warranty
All Ready-Lite® inverter products receive 100% quality inspection before shipment to insure proper and
satisfactory operation. When operated under normal conditions, Ready-Lite® inverter products will provide
years of dependable service. This unit is backed by a 1/9 year warranty. The unit is covered by a complete
1-year warranty against defects in material or workmanship, and a 9-year prorata battery warranty.
The inverter unit shall be Ready-Lite® model: __________________.
Electrical Characteristics & Dimensions
MAx. input rating
power
rating
120VAC
300W
2.70
600W
5.40
cabinet dimensions
weight
weight w/o
battery
347VAC
sine
wave
installation
W”
H”
D”
120V
347V
120V
347V
0.93
Pure
Wall
27”
12.2”
7.3”
1
41 lbs
51 lbs
18 lbs
28 lbs
1.87
Pure
Wall
24”
10.5”
20”
2
86 lbs
98 lbs
40 lbs
52 lbs
no. of battery
1000W
9.23
3.19
Pure
Wall
24”
14.5”
20”
2
137 lbs
156 lbs
59 lbs
78 lbs
1440W
12.90
4.46
Pure
Wall
24”
14.5”
20”
2
184 lbs
208 lbs
71 lbs
95 lbs
182
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Wiring Diagram
Mini-inverter
Series
120V Emergency
Lighting Load
Fluorescent, LED, Incandescent
Interruptible Unit Equipment
Load Neutral
Neutral
120 Vac
Line 120VAC switched
120VAC Load Line
Relay CTRL
Line 120VAC unswitched
Charger
Inverter
CTRL
+
+
Inverter
-
-
+
Battery
-
-
347V Emergency
Lighting Load
+
Battery
Fluorescent, LED, Incandescent
Load Neutral
Neutral
Line 347VAC switched
347 Vac
347VAC Load Line
Line 347VAC unswitched
Relay CTRL
Charger
+
-
Inverter
CTRL
+
Inverter
-
-
+
+
Battery
POWER CONSUMPTION AND UNIT RATING
Model Number
Emergency power available for load
AC Specs
30min
1h00
1h30
2h00
4h00
300W
175W
125W
100W
50W
5.40 / 1.87 Amps
600W
350W
250W
200W
100W
9.23 / 3.19 Amps
1000W
585W
415W
330W
165W
12.90 / 4.46 Amps
1440W
842W
600W
480W
240W
2.7 / 0.93 Amps
RMI-300
RMI-600
120 / 347Vac
RMI-1000
RMI-1440
Ordering Information
Series
RMI= Series
Capacity
-300= 300W
-600= 600W
-1000= 1000W
-1440= 1440W
Voltages In/Out
-1= 120/120VAC
-3= 347/347VAC
Options
-SAC= Service alarm contact*
-D3= Time Delay (15 minutes)
-LC= Line Cord (120V only, 1 000W max.)
-TL= Twist Lock Plug (120V only, 1 000W max.)
Blank= Self-Diagnostic, non audible**
-AD= Self-Diagnostic, audible**
-NEX= Nexus® wired system interface***
-NEXRF= Nexus® wireless system interface***
-10V= L ighting control override for 0-10V dimming
system***
* Not available with 1000 & 1440 capacities
** Minimum load required: 10% of unit capacity
*** For any other lighting control system, please consult your sales
representative
E x a m ple : R M I - 1 4 4 0 - 1
183
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
CHARGER/CONTROLS
Ready-lite®’s solid state fully automatic charger features single module control board design. This feature
provides cost effective superior performing equipment, with ease of maintenance and service ability.
STANDARD FEATURES AND CONTROLS
RL4 Series
120 Vdc Central Single Source
Emergency Lighting System
Time and labour saver only
one conduit required!
In an existing or new installation where
exit signs and emergency lighting may be
supplied by a single 120VDC source using
a common negative wire, one normally on
positive and one normaly off positive. 3
wire output from the system reduces the
number of conductors by up to 40%. It also
eliminates 50% of the conduit, EMT or BX
runs by using a single common conduit for
LED exits and emergency lighting remotes.
FEATURES
• Single-source 120VDC supply for both
exit and emergency lights
• Reduced number of conductors
• Eliminates 50% of conduit, BX or EMT
runs for exit and emergency lighting
• Control and supervision functions on
single modular board
• Complete package of full supervisory
functions and alarms included in
standard unit
• Floor-mount cabinet
• Battery is sealed maintenance free
lead calcium
• All RL4 Series systems are designed
and manufactured in Canada
• CSA and Ontario Hydro approved
• BMEC (Building Materials Evaluation
Commission) approved for compliance
to the Ontario Building Code
• Overall reduction on power
consumption using LED Exit Signs
enclosures
RL4 Series Central Emergency Lighting
Systems are available in free-standing
cabinet style enclosures
• Heavy duty, sheet-steel cabinet
• Cabinets are painted ASA No. 61 grey
electrolyte resistant enamel
• Locking and hinged front door
• Front access to battery charger for ease
of inspection and servicing
APPROVALS
• CSA Certified
• Ontario Hydro: Rule 46-108 (3)
• LVD at 91% of nominal
• Temperature Compensation
• Ground Fault Alarm (Audible & Visual)
• DC Volt & Ammeter (2% Accuracy)
• AC present LED indicator
• Float level Charge LED indicator
• Equalize level Charge LED indicator
• Charger Failure Alarm
• AC Failure Alarm
• AC Input Breaker
• High Battery Voltage Alarm
• Test Switch
• Remote Monitor Alarm Panel
• Brownout Protection
• Dry Contacts
• BMEC - Ontario Building Materials Evaluation Commission Approved
• SPF - sprinkler-proof cabinet comes with drip shield
OPTIONAL FEATURES CODE
• Time Delay • 3 Phase Sensing • 12 Hour Recharge • Battery exerciser
• Input battery circuit breaker • Common Zone sensing • Individual zone sensing
TD
3PH
12HR
CYC
BCB
ZSC
ZSI
application
New construction or retro-fit, the RL4 Series utilizes the latest technology and engineering to reduce the cost
of emergency lighting installations. The unique 3 wire design allows for the use of just one conduit. With one
positive dc normally energized conductor and a common negative conductor the LED exits are supplied constant
power. With the same common negative conductor and another positive DC conductor the remote emergency
lights are powered on demand. Available in sizes from 4120W to 22520W for 30 minutes. Other runtimes
available. Please consult factory.
ELECTRICAL
Input: 120V, 208V, 240V, 277V, 347V, 600VAC 60HZ Single Phase
Output: 120VDC 3 wire (normally on positive, common negative and normally off positive).
Systems have been designed for minimum 1/2 hour operation time and are capable of full recharge in 24 hours. For
systems rating chart and ordering guide please see next page. Other discharge times are available upon request.
WARRANTY
The complete system is guaranteed for a period of one (1) year against defects in workmanship and materials.
The battery portion of the equipment carries a ten (10) year pro-rata warranty during its useful service life
against defects in workmanship and materials. The battery warranty is subject to the provision of normal
testing and inspection as specified in the Canadian Electrical Code, Section 46-102, and National Fire
Code of Canada. Limit room ambient temperature between 20°C to 25°C (68°F to 77°F). Optimum system
performance occurs at 25°C (77°F). A battery service life is defined as the period which the battery could still
provide at least 80% of its rated capacity.
DISTRIBUTION OPTIONS
A separate distribution panel is available for all systems. A choice of fuses or circuit breakers is available. Fuse Distribution Panel Select -OPF ( ) for separate distribution fuse panel. Select -OFA ( ) for separate distribution fuse panel with
visual and audible alarm on main console for failure of any fuse. Circuit Breaker Distribution Panel Specify - CBO ( ) for
separate circuit breaker panel. Specify - OCA ( ) for separate circuit breaker panel with visual and audible alarm on main
console for tripping or opening of any breaker.
184
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Unity Series
ENCLOSURE DIMENSIONS
H120VDC
X W X D Central Single Source
SYSTEM SERIES
Emergency Lighting System
RL4 4120
38” (96.5 cm) x 38” (96.5 cm) x 18” (45.7 cm)
RL4 9390-11260
38” (96.5 cm) x 38” (96.5 cm) x 28” (71.1 cm)
RL4 13140-22520
56” (142.2 cm) x 38” (96.5 cm) x 28” (71.1 cm)
RL4 Series
UNIT RATING
SG Series batteries: maintenance free, sealed Lead-Calcium. Watts at 91% of nominal voltage.
CAPACITY IN WATTS
30 MIN
1H00
1H30
2H00
RL4 4120
4 120
2 450
1 790
1 440
RL4 9390
9 390
5 590
4 080
3 290
RL4 11260
11 260
6 700
4 890
3 940
RL4 13140
13 140
7 820
5 710
4 600
RL4 18780
18 780
11 180
8 160
6 580
RL4 22520
22 520
13 400
9 780
7 880
120 Vdc Central Single Source
Emergency Lighting System
TYPICAL INTERCONNECTION WIRING DIAGRAM
EXIT
BATTERY BACKUP
CONDUIT
CONDUIT
SINGLE SUPPLY UNIT
NORMAL EMERGENCY POWER SUPPLY UNIT
WITH EXIT SIGN AND REMOTE HEADS
CONDUIT
CAD Drawing illustrates how the Rl4 Series is applied,
saving time, material and money. Call your local
ready-Lite® Representative for further information, or application assistance.
ORDERING INFORMATION
SYSTEM
DESIGNATION
A.C. INPUT
VOLTAGE (1PH)
RL4
120= 120VAC
208= 208VAC
240= 240VAC
277= 277VAC
347= 347VAC
600= 600VAC
BATTERY
TYPE
SG = sealed
Lead
Calcium
CAPACITY
IN WATTS
4120
9390
11260
13140
18780
22520
QTY OF EXIT
SIGNS
100E= 1
00 Exit
Signs
MOUNTING
D.C. OUTPUT
VOLTAGE
C= Console
120= 120VDC
OPERATING TIME
30= 30 minutes
60= 60 minutes
90= 90 minutes
120= 120
minutes
For other
discharge times,
please consult
your sales
representative.
185
DISTRIBUTION
OPTIONS
OPF()= fuse panel*
OFA()= fuse panel
with alarm
CBO()= circuit
breaker
panel*
OCA()= circuit
breaker
panel with
breaker trip
alarm
*Specify number of
circuits
OPTIONS
TD= Time delay
(15 minutes)
3PH= 3 phase
sensing
12HR= 12 hour
recharge
CYC= Battery
exerciser
BCB= B
attery circuit
breaker
ZSC()= Common zone
sensing*
ZSI()= Individual
zone sensing*
* Specify No. of zones.
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Made in Canada
CHFEATURES
Series
CHARGER
RL Series
DC Central,
Emergency Lighting System
Fully automatic charger,
battery and specified
transfer and distribution
features
Ready-Lite®’s DC Systems are utilized
where a large number of remote heads
or standard 120V incandescent fixtures
may be supplied from a single source.
The systems offer the advantage of a
central location for maintenance with full
supervision of all operating functions.
Contact your Ready-Lite® representative for
information.
FEATURES
• 24, 36 and 120 VDC systems sealed
lead acid batteries
• Control and supervision functions on
single modular board
• Complete package of full supervisory
functions and alarms included
in standard system
• Totally sealed maintenance free Lead
Calcium batteries
• All systems are designed and
manufactured in Canada
• CSA certified
• BMEC (Building Materials Evaluation
Commission) approved for compliance
to the Ontario Building Code
BATTERy
Sealed Maintenance-Free Lead Calcium Gas
Recombination (SG Series)
Uses gas recombination to eliminate the
escape of hydrogen. Thick plates are constructed of high strength material which
resists shedding, flaking, or mechanical
failure. Design Life: 10 years under normal
operating conditions.
Model No.:
Central
Emergency
Lighting
System
Ready-Lite®DC
has
developed
a unique
modular
charger design in which all electronic control functions and
pilot lights are mounted on a single control board. This is connected to the operating power components
using screw type connectors– making the circuit board easily removable by means of only four screws.
Any required field service, consequently, is faster and significantly simpler than with older style multiple
board designs. All chargers include a contactor which automatically disconnects the batteries from the load
when battery bank voltage falls below 91% of nominal, in order to prevent over-discharge of batteries. The
operating temperature for the system is from 20ºC to 25ºC (68ºF to 77ºF). The control board is temperature
compensated in order to meet the battery required float voltage at temperatures below and above 25°C,
as recommended by battery manufacturers. Internal control allows for spark free battery bank connection
during installation and scheduled maintenance procedures.
CHARGING OPERATION
The charger will fully recharge the battery within a twenty four hour period from a full discharge. The
charger maintains regulation of ± 0.5% of voltage for a ± 10% input voltage variation. The charger provides
automatic equalize cycle whenever the charge current is more than a preset value. The charger operates in
an equalize mode after each utility power return. This ensures maximum battery capacity at all times, with
maintained life expectancy
STANDARD CONTROLS
The front panel includes the following controls:
• DC Battery Voltmeter (2% Accuracy)
• DC Charge Rate Ammeter (2% Accuracy)
• Green “ac on” LED (on at all times except during power failure)
• Green “float” LED (indicates that the battery is receiving float charge
to maintain the battery at full charge at all times)
• Amber “equalize” LED (indicates that the charger is in the high charge
equalizmode, balancing the charge level in the individual battery cells)
• Brown-out protection
• Test switch
• A.C input circuit breaker
STANDARD ALARMS
• AC Failure LED and Alarm
• High Battery Voltage LED and Alarm
• Charger Failure LED and Alarm
• Ground Leakage Alarm
• An audible alarm and a common LED shall indicate “Ground
Leakage” and/or Fuse/Circuit Breaker open/trip alarm
• High ambient temperature
DISTRIBUTION OPTIONS
A separate distribution panel is available for all systems. A choice of fuses or circuit breakers is available.
Fuse Distribution Panel Select -OPF ( ) for separate distribution fuse panel. Select -OFA ( ) for separate
distribution fuse panel with visual and audible alarm on main console for failure of any fuse.
Circuit Breaker Distribution Panel Specify - CBO ( ) for separate circuit breaker panel. Specify - OCA ( ) for
separate circuit breaker panel with visual and audible alarm on main console for tripping or opening of any
breaker.
Note: “( )” indicates the number of circuits required.
TRANSFER OPTIONS
• System may be selected to either turn on a normally “off” load or alternatively on 120VDC systems,
maintain a normally “on” load
• Normally “off” (DC load): (CP)
• If the lamp load is going to be turned on in the event of power failure add suffix –CP to the model number
• Normally “on” (AC/DC load): (TS) 120 V DC systems only
• The 120V incandescent load shall have 120VAC power normally supplied to it and the load shall be transferred to 120VDC upon failure. Add suffix –TS to the model number. For other AC input voltages please
contact factory
• Both Normally “on” & “off” loads: (CP/TS)
• Both of the above apply
186
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
OTHER OPTIONS
Time delay, specify time 1-10 minutes
-TD ( )
3 phase sensing -3PH
Battery circuit breaker -BCB
Battery exerciser-CYC
Common Zone Sensing -ZSC( )*
Individual zone sensing, specify number of zones (external panel)
-ZSI( )*
* Zone explanation: each specified zone relay monitors an individual lighting circuit in a building. Should the monitored circuits lose AC
power, the connected lighting load will automatically illuminate:
a - all zones if ZSC is specified
b - that zone only if ZSI is specified
CABINETS
Systems are available in a free standing floor mount cabinet. The cabinet shall be constructed of not less
than 14 gauge steel with corrosion resistant undercoating. Standard finish is ASA61 grey baked enamel.
WARRANTY
The complete system is guaranteed for a period of one (1) year against defects in workmanship and
materials. The battery portion of the equipment carries a ten (10) year pro-rata warranty during its useful
service life against defects in workmanship and materials. The battery warranty is subject to the provision of
normal testing and inspection as specified in the Canadian Electrical Code, Section 46-102, and National
Fire Code of Canada. Limit room ambient temperature between 20°C to 25°C (68°F to 77°F). Optimum
system performance occurs at 25°C (77°F). A battery service life is defined as the period which the battery
could still provide at least 80% of its rated capacity.
TYPICAL SPECIFICATION
Provide and install a complete emergency lighting system as described herein and shown on the drawings.
The system shall consist of a charger, battery and specified transfer and distribution features. The charger
shall be fully automatic solid state type using integrated circuit control. The output voltage variation shall be
± 0.5% for input variation of ± 10%. The charger shall recharge the battery within 24 hours after a power
failure. The charger shall include a contactor to automatically disconnect the battery from the load when
the battery voltage falls below 91% of nominal. The charger shall be of a modular design with all pilot lights
and electronic control functions on a single board mounted behind the front panel. The single control board
shall have LED pilot lights for the following functions (which shall show through the front panel):
• Green “ac on” LED
• Green “float” Charge LED
• Amber “equalize” LED
• AC Failure
• High Battery Voltage
• Charger Failure
• Battery Ground Leakage
• High ambient temperature
OPTIONAL ALARMS
• Fuse/Circuit Breaker Open/Trip
SELECT SG BATTERY
Select battery bank voltage, capacity and duration of required backup time. Select AC input voltage. Select
system transfer option from CP (), TS( ), or CP( )/TS( ) where the load watts are shown in brackets.
SELECT OPTIONS
The equipment shall be provided with a separate distribution panel with _____ fuses or circuit breakers
(select one) rated at ______ Amps.
Optional: All distribution fuse or circuit breaker panels shall be alarmed sothat if a fuse or circuit
breaker has failed during operation, a visual and audible alarm is activated. The system shall be –
Ready-Lite® System RL (select model number from ordering informationchart). Select remote fixture
from fixture section of Catalogue.
187
RL Series
DC Central,
Emergency Lighting System
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
CABINET DIMENSIONS
system
DIMENSIONS H X W X D
RL24SG820-3755
25” X 29” X 14”
RL36SG1230-3375
RL36SG3940
RL Series
38” X 38” X 18”
RL120SG4120
120 VDC Central,
Emergency Lighting System
RL120SG5660-11260
38” X 38” X 28”
RL120SG13140-22520
56” X 38” X 28”
Electronics and batteries are in the same cabinet.
FEATURES
• One set of dry contacts for remote
fault sensings
• Remote alarm panel
• Drip shield (2.5” overhang on console)
• Brownout
• Remote alarm panel
SG Series :
sealed maintenance free lead acid Battery Capacity Chart 25 C
o
NOMinAL BACKUP CAPACITY
MODEL
30 min
60 MIN
90 Min
120 Min
A
RL24SG820
820W
490W
355W
285W
B
RL24SG1130
1130W
800W
585W
470W
C
RL24SG1875
1875W
1115W
815W
655W
D
RL24SG2250
2250W
1340W
975W
785W
E
RL24SG2625
2625W
1560W
1140W
920W
F
RL24SG3755
3755W
2235W
1630W
1315W
G
RL36SG1230
1230W
730W
537W
432W
H
RL36SG1695
1695W
1205W
880W
705W
I
RL36SG2815
2815W
1675W
1220W
985W
J
RL36SG3375
3375W
2010W
1465W
1180W
K
RL36SG3940
3940W
2345W
1710W
1380W
L
RL120SG4120
4120W
2450W
1790W
1440W
M
RL120SG5660
5660W
4015W
2935W
2355W
N
RL120SG9390
9390W
5590W
4080W
3290W
O
RL120SG11260
11260W
6700W
4890W
3940W
P
RL120SG13140
13140W
7820W
5710W
4600W
Q
RL120SG18780
18780W
11180W
8160W
6580W
R
RL120SG22520
22520W
13400W
9780W
7880W
All capacities are in watts to 91% of nominal voltage. Note: For other voltages and capacities contact your sales representative.
ORDERING INFORMATION
SYSTEM
DESIGNATION
RL
D.C.
OUTPUT
VOLTAGE
24= 24VDC
36= 36VDC
120= 120VDC
BATTERY TYPE
SG= sealed
Lead-Calcium
A.C. INPUT
VOLTAGE
(1PH)
CAPACITY
IN WATTS
OPERATING
TIME
__________*
30= 30 min
60= 60 min
90= 90 min
120= 120 min
120= 120VAC
208= 208VAC
240= 240VAC
277= 277VAC
347= 347VAC
600= 600VAC
* Select from
Battery
Capacity
chart in
folder
188
TRANSFER OPTIONS
DISTRIBUTION
OPTIONS
CP= n
ormally off load
TS= n
ormally on load
CP()/TS()= n
ormally on
and off load*
OPF()= fuse panel*
OFA()= fuse panel
with alarm
CBO()= circuit
breaker
panel*
OCA()= circuit
breaker panel
with breaker
trip alarm
*Specify Watts for each
type of load.
*Specify number of
circuits
OPTIONS
TD= Time delay
(15 minutes)
3PH= 3 phase
sensing
12HR= 12 hour
recharge
CYC= Battery
exerciser
BCB= Battery circuit
breaker
ZSC()= Common zone
sensing*
ZSI()= Individual zone
sensing*
* Specify No. of zones.
central system
datA request
1) Input voltage
Single phase
(2 wire + ground)
Single phase
(3 wire + ground)
208VAC
277VAC
120/208VAC
277/480VAC
347/600VAC
208VAC
480VAC
600VAC
277VAC
120VAC
347VAC
120/240VAC
Three phase
(4 wire + ground, Y)
Three phase
(3 wire + ground, Δ)
2) Output voltage
Single phase (2 wire + ground)
120VAC
208VAC
Single phase (3 wire + ground)
120/240VAC
120/277VAC
Three phase
120/208VAC
277/480VAC
(4 wire + ground, Y)
347VAC
347/600VAC
3) System capacity
KVA rating:
a) Please consider total power consumption of the complete fixture, not just the lamp wattage
b) Even if the systems can run with 100% load, it is recommended as standard practice to use a system with a capacity at least 20% over
maximum connected load
4) Runtime
30 minutes
60 minutes
90 minutes
Fluorescent
L.E.D.
120 minutes
Other
5) Type of loads
Incandescent
Others
6) Mode of operation
Normally ON (24/7)
Normally OFF (emergency only)
7) output circuit breakers
# of CB
Amps
# of poles
Normally “On”
Normally “Off”
Trip alarm
# of CB
Amps
# of poles
Normally “On”
Normally “Off”
Trip alarm
8) Options (refer to available options for each system type)
(-A) 12 Hour Fast Recharge
(-K) Anchor Mounting Kit
(-C) Remote Summary Alarm Panel
(-L) Drip Shield
(-E) Output Trip Alarm
(-M) Second Output Terminal Block
(-G) Inverter On Dry Contacts
(-N) Normally On & Normally Off outputs
(-H) Normally Off Output
(-I) Extended Battery Warranty
(-J) E
xternal Maintenance Bypass
Switch
189
A large selection of options and
accessories to choose from to add on
to your emergency lighting products.
From wire guards to retrofit kits, we
have what you need.
led retrofit kits
P. 194-196
nexus
P. 202
bulb
pendant kit
P.196
ZCP
P. 203
P. 197
eZ2
P. 198
RIB
P. 199
n
n = new product
193
Wire guards
P. 200-201
table
of
contents
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
how much can you save?
The following is an example of the savings you can generate by simply installing an LED retrofit kit in an
existing incandescent Exit Sign.
LED Retrofit
Kits
Convert high-consumption
incandescent and
fluorescent lamps to
energy-efficient LED
lamps
Converting existing Exit Signage from
incandescent or fluorescent lamps to LED
(light emitting diodes) lamps drastically
reduces operating and maintenance
costs for building owners and property
managers. As part of energy-efficiency
programs, some Canadian electric utilities
are also actively promoting conversion to
LED with incentive and rebate programs
for installers and building owners/
managers.
Features
your Payback Analysis
The Retrofit Kit Cost:
Installation cost (per unit) for a
retrofit kit (Labour):
Wattage rating per incandescent lamp in existing
fixture:
Number of incandescent lamps per fixture:
Wattage rating of Ready-Lite MB1UN retrofit kit:
My existing incandescent exit lamps last for:
$70.00
$5.00
15W
2
1.7W
4 Months
My replacement labour cost:
$25.00/Hour
Estimated lamp replacement
time per exit:
20 Minutes
Current material cost for each
Exit Sign lamp:
$1.00/Lamp
My current energy cost:
$0.060/$ Per kWh
Ready-Lite® offers four retrofit kit options; all
based on the long-life ALINGAP LED technology:
• SB Series
• Mini-Bar Series
• Mini-Bar “D” Series
• RLB Bulb Series
Benefits of using LED lamps in Exit Signs:
• Exceptional energy-efficiency – reduces
energy consumption by up to 90%
• Extremely long life – 10 to 25 years
• Important reduction in maintenance
and energy costs
• Average payback is less than two years
• Retrofit kits are easy to install
• Improved visibility and reliability:
ALINGAP LED technology
The PAYBACK FOR YOUR INSTALLATION IS:
THE ANNUAL RETURN ON INVESTMENT IS:
ANNUAL SAVINGS:
For more information, please consult your sales representative.
194
1.06 Years
94.50 %
$70.87
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
mini-bar “D” Series
dimensions
Dimensions are approximate and subject to change.
m]
LED Retrofit
Kits
13/16” [2.1 cm]
4.1 c
2” [2
9-1/
mini-bar “D” Series
features
• Easiest to install in its class
• Compact size makes it ideal for virtually
all Exit Signs
• Can be retrofitted directly on
fluorescent ballast
• Suitable for all AC line applications
including Exit Signs equipped with
in-line diodes
• Long-life, energy-efficient ALINGAP
LED techonology
13/16” [3 cm]
Power consumption
Model
AC Specs
MB*D
DC Specs
120VAC; 120VAC with in-line diodes
2.8W
N/A
N/A
ordering information
Series
voltage
MB= for
standard
applications
1= 120VAC
model
D= with or without
inline diodes, high
brightness
options
C= candelabra
I= intermediate
M= medium
B= bayonet
CIMB= complete set of bases
EXAMPLE: MB1DC
mini-bar Series
features
mini-bar Series
• Easiest to install in its class
• C ompact size makes it ideal for virtually
all Exit Signs
• C an be retrofitted directly on fluorescent
ballast
• Long-life, energy-efficient red ALINGAP
LED technology
• Available with AC adaptor for all types
of lamp sockets
• 10 year limited warranty
dimensions
Dimensions are approximate and subject to change.
24.1
2” [
9-1/
cm]
13/16” [2.1 cm]
1-3/16” [3 cm]
Power consumption
Model
MB
AC Specs
120VAC; 86VAC step down from 347VAC
DC Specs
0.65W
N/A
N/A
ordering information
Series
MB
voltage
1= 120VAC
2= 277VAC (hardwire)
3= 347VAC (hardwire)
4= 240VAC (hardwire)
options
C= candelabra
I= intermediate
M= medium
B= bayonet
F= G23 compact fluorescent
UN= c omplete set of bases (excludes “F”
base)
EXAMPLE: MB1C
195
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
rlB bulb
dimensions
Dimensions are approximate and subject to change.
15/16” [2.5 cm]
4-3/4” [12 cm]
3-3/4” [9.6 cm]
5-1/3” [13 cm]
3-3/4” [9.6 cm]
LED Retrofit
Kits
1-1/4” [3.2 cm]
RLB BULB Series
features
• Quick and easy to install
• Available with a wide range of lamp
bases for quick lamp to lamp
replacement
• Long-life, energy-efficient ALINGAP
LED techonology
• 120VAC or 120VAC with in-line diode
1-3/16” [2.1 cm]
13/16” [2.1 cm]
Power consumption
Model
AC Specs
DC Specs
RLBH
120VAC
0.90W
N/A
N/A
RLBD
120VAC
2.6W
120VDC
2.6W
ordering information
Series
BASE
RLBH= standard version
RLBD= with or without in-line diodes (2.5W), high
brightness
-C= candelabra
-I= intermediate
-M= medium
-B= bayonet
-F= G23 compact fluorescent (not available for RLBD)
EXAMPLE: RLBH-C
SB Series features
• Quick and easy to install
• Long-life, energy-efficient red ALINGAP
LED technology
• Module features two independent
circuits – one for AC input; one for
DC input
• Universal AC input: 120/277/347VAC;
universal two-wire DC input: 6 to 24VDC
• Power consumption of 1.1W per
module
• 10 year limited warranty
SB series
dimensions
Dimensions are approximate and subject to change.
m]
8.3 c
8” [2
/
11-1
13/16” [2.1 cm]
1-3/16” [3 cm]
Power consumption
Model
SB
AC Specs
120/277/347VAC
DC Specs
1.1W
6 to 24VDC
1.3W
ordering information
Series
SB= hardwire retrofit kit
voltage
-LU= 1
20/277/347VAC, 6/12/24VDC
-LU36= 1
20/277/347VAC, 36VDC
-LU48= 120/277/347VAC, 48VDC
-LU120= 120/347VAC, 120VDC
-L120-2W= 1
20VAC,120VDC, 2 wires
EXAMPLE: SB-LU
196
Options
Blank= 11.0” (28 cm) long
-9.5= 9
.5” (24 cm) long*
*Available in -LU voltage only.
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
Offered in a variety of colours and lengths, Ready-Lite® Pendant Kits are designed to facilitate the installation of Exit Signs at regular mounting heights.
Compatible with both horizontal and sloped ceilings, these Pendant Kits is truly universal and will adapt to
any application.
Please consult your sales representative.
Pendant Kit
Dimensions
Dimensions are approximate and subject to change.
P3R
Length
P1R
P2R
P4R
ordering information
Series
length (in)*
colour
P1R
standard model of pendant
6
12
18
24
W= white
B= black
SG= silver grey
P2R
Legend™ series
6
12
18
24
W= white
B= black
SG= silver grey
P3R
Aluminum slim edge-lit
6
12
18
24
W= white
B= black
SG= silver grey
P4R
Ultima™ plastic exit
6
12
18
24
W= white
B= black
SG= silver grey
*Other lengths available by request. Consult your sales representative.
197
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Typical specifications
The EZ2™ Canopy allows the installer to make all of the electrical connections using both hands without
having to juggle with the Exit Sign, making it our most contractor friendly product feature to date.
Simply attach the backplate to the junction box, clip the canopy on the Exit Sign, hang the canopy on the
back plate, make your connections using both hands, slide the unit in place, one screw and the job is done!
EZ2™ Canopy
dimensions
Dimensions are approximate and subject to change.
Quick and Easy Installation
6-3/8”
1-1/32”
4-11/16”
See detail A
See detail C
See detail B
3. Connect the wires, then align and slide
the sign to its final position.
1. Attach the backplate/spider to the
wall before assembly.
2. Hang the unit using
the tabs and the wire eyes.
Detail A
Scale 3.000
Detail C
Scale 3.000
Detail B
Scale 3.000
198
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
Typical specifications
RIB Series: The electrical contractor shall supply and install Ready-Lite® FPS Series remote fluorescent
inverter ballasts for each fixture as shown on plans. The inverter shall operate on
VDC input for
minutes during a power failure. The fluorescent lamp shall be maintained at
% lumen
output for one lamp only. The inverter is to be connected to the remote battery unit as shown on plans
(battery unit to be selected according to voltage/wattage and duration required). The inverter shall be
capable of illuminating the fluorescent lamp even when it is burned out under normal AC operation.
RIB Series: The electrical contractor shall supply and install Ready-Lite® FEB Series fluorescent inverters
for each fixture as shown on plans. The FEB Series inverter shall operate for
minutes during a
power failure. The fluorescent lamp shall be maintained at
% of nominal lumen output. The FEB
Series inverter shall be capable of illuminating the fluorescent lamp even when it is out under normal AC
operations.
.
Dimensions
T ENCLOSURE (factory white)
ldx-EXP-s
Series
3-1/4”
[8.3 cm]
15-1/4” [38.7 cm]
7-1/4” [18.4 cm]
1-1/2”
[3.8 cm]
2-3/4”
[7 cm]
20-7/8” [53 cm]
4-5/8”
[11.7 cm]
23-3/4” [60.3 cm]
3” [7.6 cm]
Battery(white)
Units, Self-powered
R ENCLOSURE
“Sortie” Signs Combo Units
Fluorescent Inverters
Features
Dimensions are approximate and subject to change.
INTERNAL ENCLOSURE (BLACK)
rib Series
1-1/2” [3.8 cm]
• All RIB Series are fully load tested
prior to shipment
• Inverter is 100% solid state, short and
open circuit proof
• Polarized DC input (FPS Series only)
• 120VAC 60Hz input is standard, 277
and 347VAC available as options
• 25%, 50% or 80% lamp lumen output
• Mounts directly in ballast channel,
remote or optional T-Bar fixture
• CSA listed
4-1/2” [11.4 cm]
9-5/8” [24.4 cm]
2-1/2”
[6.4 cm]
RIB enclosure (white) - internal
D.C. power consumption
series
output %
lumens
RIB-800
25
800
Watts
10
RIB-1600
50
1600
20
RIB-3200
80
2560
32
ordering information FPS series
series
lumens / (%) for 48” tube
RIB6= 6V
RIB12= 12V
RIB24= 24V
RIB32= 32V
RIB48= 48V
RIB120= 120V
voltage
25= 2
5% (800 lumens) lumen outputs based on averages
50= 5
0% (1600 lumens) 24”/20W=1260 48”/40W=3200 96”/75W=6300
80= 8
0% (2560 lumens) inverters will operate T12, T8, or “U” type lamps
Blank= 120VAC
U277= 277VAC
U347= 347VAC
EXAMPLE: RIB625
ordering information FEB series
Series
FEB
lumens / (%) for 48” tube
min. runtime
25= 25% (800 lumens) lumen outputs based on averages
50= 50% (1600 lumens)
24”/20W=1260 48”/40W=3200 96”/75W=6300
80= 80% (2560 lumens) inverters will operate T12, T8, or “U” type
lamps
E X A M P L E : feb 5 0 - 9 0 R
199
housing
-30= 30 minutes
-60= 60 minutes
-90= 90 minutes
-120= 1
20 minutes*
Blank= internal*
R= remote
mounting
enclosure
T= T-Bar
*FEB80 in T-Bar cabinet
only.
*Not available for
FEB80.
ac voltage
Blank= 120VAC
U277= 277VAC
U347= 347VAC
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
exit signs
part #
wire guards &
Mounting
shelves
mounting
dimensions
signs
w
h
d
End Mount
CX2000
CX5000
TUF
ULTD
RA
RT
CX4000
NEXTN
RN
RS1000
RS
RP
ULT
RX
10-1/2”
(26.7 cm)
6” (15.2 cm)
16”
(40.6 cm)
460.0028-RL
Ceiling
Mount
CX2000
CX5000
TUF
RT
ULTD
RA
RP
CX4000
NEXTN
RN
RS1000
RS
ULT
RX
14-1/2”
(36.8 cm)
6-1/4”
(15.9 cm)
10-1/2”
(26.5 cm)
460.0034-RL
Wall Mount
LD12-S Sortie
CX9000BIL
CS9000BIL
LD12E (Large)
LD6-IF
28-1/8”
(71.5 cm)
21-1/8”
(53.7 cm)
10”
(25.4 cm)
460.0048-RL
End Mount
CS2000
CS5000
CS4000
CNESTU
10-1/2”
(26.7 cm)
6”
(15.2 cm)
21”
(53.3 cm)
460.0057-RL
Wall Mount
CS2000
CS5000
CS4000
CNESTU
20-3/4”
(52.7 cm)
10”
(25.4 cm)
4”
(10.2cm)
460.0058-RL
Ceiling
Mount
CS2000
CS5000
CS4000
CNESTU
21-3/4”
(55.2 cm)
5-1/2”
(14 cm)
10-1/2”
(26.7cm)
460.0059-RL
Wall Mount
CX7000
CNSXTN
31”
(86.4 cm)
10”
(25.4 cm)
4-1/2”
(14 cm)
460.0060-RL
End Mount
RAC
SM-NEXTN
SM-CX5000
20”
(50.8 cm)
12”
(30.5 cm)
15”
(38.1 cm)
460.0060-RL
Ceiling
Mount
R-SN
ULT Combo
N-TUF
RH
TUF-HZ
20” (50.8
cm)
12”
(30.5 cm)
15”
(38.1 cm)
460.0078-RL
Wall Mount
RNC
Ultima™ Combo
18”
(45.7 cm)
18”
(45.7 cm)
7”
(17.8 cm)
NEXTN
Ultima™ Exit
RN
RS
RS1000
ULTD
14-1/4”
(36.2 cm)
9-7/8”
(25.0 cm)
4-5/8”
(11.7 cm)
TUFHZ
RSC
RAC
15-1/4”
(38.7 cm)
14-1/8”
(35.9 cm)
6-1/2”
(16.5 cm)
460.0027-RL
CX4000BIL
CS4000BIL
CNEXTN
CS7000
N-TUF
RNC
RSC
RNC
SM-CX5000
SM-CS5000
SM-NEXTN
RAC
RSC
N-TUF
RHC
HZ
CX2000
CX5000
TUF
RT
CX4000
RP
RA
SM-NEXTN
SM-CX5000
RH
460.0079-RL
Wall Mount
460.0080-RL
Wall Mount
460.0081-RL
Wall Mount
SM-CS5000, CS9000N,
LD12E (Small), R-SN
20”
(50.8 cm)
17-1/8”
(43.6 cm)
8-1/2”
(21.6 cm)
460.0091-RL
Wall Mount
CX5000R
15”
(38.1 cm)
10-1/2”
(26.7 cm)
1”
(2.5 cm)
460.0092-RL
Ceiling
Mount
31”
(53.3 cm)
4.5”
(11.4 cm)
10”
(25.4 cm)
460.0104-RL
Ceiling
Mount
25”
(63.5 cm)
10”
(25.4 cm)
20”
(50.8 cm)
200
CS4000BIL
CX4000BIL
CNEXTN
CX7000
CNSXTN
CS7000
LD6-IF, CS9000N,
CX9000BIL, CS9000BIL
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Battery Units
part
mounting
commercial,
deco unit
460.0078-RL
Wall Mount
460.0081-RL
dimensions
w
h
d
“A” Cabinet-6V, 12V,
24V-Max. 144W
17” (45.7 cm)
17” (45.7 cm)
7” (17.8 cm)
Wall Mount
“B” Cabinet-6V-180W
12V-216 to 360W
24V-200 to 288W
20” (50.8 cm)
17-1/8” (43.6 cm)
8-1/2” (21.6 cm)
460.0034-RL
Wall Mount
“C” Cabinet
24V-350 to 720W
28-1/8” (71.5 cm
21-1/8” (53.7 cm)
10” (25.4 cm)
460.0097-RL
Wall or
Ceiling
Mount
LDX-VQ
31”(53.3 cm)
7”(17.8 cm)
6”(15.2 cm)
460.0080-RL
Wall Mount
LDXC, LDXA, Ultima
15-1/4”
(38.7 cm)
14-1/8” (35.9 cm)
6-1/2” (16.5 cm)
460.0010-RL
Wall or
Ceiling
Mount
C29, B29
14” (35.6 cm)
5.8” (14.7 cm)
5.6” (14.2 cm)
wire guards
& mounting
shelves
Industrial
460.0082-RL
Wall Mount
Small Cabinet
12” (30.5 cm)
9” (3.5 cm)
9” (3.5 cm)
460.0081-RL
Wall Mount
Medium and Large
Cabinet
20” (50.8 cm)
17-1/8” (43.6 cm)
8-1/2” (21.6 cm)
IPR 48”
54.6’ (138.68 cm)
8’ (20.32 cm)
5’ (12.7 cm)
IPR 24”
30’ (76.2 cm)
8’ (20.32 cm)
5’ (12.7 cm)
460.0105-RL
460.0106-RL
Ceiling
Mount
Remote Heads
dimensions
part #
Remote Heads
W
H
D
460.0029-RL
TUF-NM, RT, RQ, RM, RL25, VQ,
RL40M, RL150
8-1/4” (21.5 cm)
6-1/4” (15.9 cm)
6-3/4” (17.2 cm)
460.0031-RL
VQW, WT2, LH2
25-1/4” (64.1 cm)
8-1/2” (21.5 cm)
8-1/2” (21.5 cm)
460.0032-RL
VQ2, RL150D
9-1/2” (24.1 cm)
9-1/2” (24.1 cm)
6-1/8” (15.6 cm)
460.0033-RL
RF105
9-1/2” (24.1 cm)
9-1/2” (24.1 cm)
4”(10.2 cm)
460.0035-RL
LT, WT, WSR
8-1/4” (21.5 cm)
6-1/4”(15.9 cm)
8-1/2” (21.5 cm)
460.0082-RL
LQ2, WT2, WSR2,
Guardian™, Cadilite™
12”(30.5 cm)
9”(22.9 cm)
9”(22.9 cm)
460.0078-RL
Triple Remote
17”(45.7 cm)
17”(45.7 cm)
7”(17.8 cm)
Mounting Shelves
Part # 440.0620-RL for “B” Cabinet
7-1/2”
(19.05 cm)
8-1/32”
(20.4 cm)
11-5/16” (28.7 cm)
15-1/16” (38.28 cm)
5-1/16”
(12.89 cm)
8-1/32”
(20.4 cm)
11-1/32” (28.02 cm)
7-1/2”
(19.05 cm)
10-29/32” (27.69 cm)
Part # 440.0625-RL for “C” Cabinet
11-1/16” (28.07 cm)
Part # 440.0616-RL for “A” Cabinet
6-3/16”
(15.75 cm)
18-1/16” (45.85 cm)
201
25-3/32” (63.75 cm)
6-3/16”
(15.75 cm)
Manage Testing with Nexus ® to Save Time and Costs
Nexus® is a real-time monitoring system that manages the status of your entire Emergency Lighting and
Exit Sign system from a central control unit. Nexus® runs diagnostics, performs required monthly and
annual functional tests, generates maintenance logs and runs compliance reports.
Available in wired or wireless (RF) versions, Nexus® installations often pay for themselves in less than two
years. In addition to operational savings, Nexus® helps increase system reliability and performance and
reduces the risk of failed inspections. One building or a group of properties under the same management
can be monitored with Nexus®.
Maximize System Availability
Nexus System
®
Are you prepared for a
safety inspection?
Building & Life Safety Codes oblige
building owners/managers to ensure the
safe evacuation of a building in the event
of an emergency. In the interest of public
safety, building owners/managers must
meet the outlined requirements for exit
signs and emergency lighting equipment,
including the following:
• Conduct a discharge test every month.
• Conduct functional tests annually.
• Keep a log book of maintenance
information.
Complying with these requirements
can be labour intensive and costly,
especially in large buildings where testing
every emergency light requires many
man-hours.
Disrupting the power supply during
lengthy inspections can also put public
safety at risk.
By allowing maintenance personnel to easily maintain and monitor the emergency lighting system without
having to manually check each unit, Nexus® reduces the hours required to disrupt the power supply
for inspections. With Nexus®, monthly tests and reports on the status of all emergency lights and exit
signs can be done individually, in groups, or together. Advantages of the Nexus® system include saving
labour; maximizing system availability by testing units in groups and stages rather than setting all units in
recovery mode; and the convenience of self-monitoring. Nexus® indicates the location of a faulty unit and
reports it instantly without requiring a manual search.
Update Status Instantly
Nexus® passes messages both to and from the emergency units to instruct the units to perform all
mandatory testing by communicating between the emergency units and a centrally located controller.
Nexus® is a proven system supported by a 5-year warranty, and can contribute to LEED certification and
support green building initiatives.
Small System Example
In a system of fewer than 100 units it is most likely that the only hardware required, other than the
emergency units themselves, is a controller. All communication would occur wirelessly and installation
would not vary greatly from a non-monitored system. Once the units are in place, the system will establish
the mesh network. The building itself could be quite large as each unit only needs to be able to communicate with its close neighbours and does not need to communicate directly with the controller.
Large System Example
The Nexus® RF system has been designed to be extremely flexible and provides for a range of system
options. Each large site will need to be assessed for the best system solution with the assistance of
Thomas & Betts technical staff. The basic Nexus® RF system is designed to run on an Ethernet network
which is present in most modern buildings; however, through a range of interface cards the backbone of
the network could be WLAN.
As with the small system example, site performance will be optimized through the careful selection and
placement of Area Controller Routers and the Area Controller to form efficient clusters. Building layout
and materials will also play some role in determining the best solution to deliver a highly effective means
of testing and maintenance requirements.
202
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
DESCRIPTION
The ZCP has several inputs to detect the AC voltage of each zone. It will activate all the emergency lighting if
at least one zone becomes de-energized through either a power failure or lighting circuit breaker tripping. This
greatly enhances the life safety system, as any failure of a lighting circuit will ensure emergency egress lighting
in the entire building. As an optional feature, the ZCP can include test buttons and/or pilot lights, enabling
individual testing of each zone circuit monitored. The ZCP can be included as an option in the Ready-Lite®
emergency lighting battery unit, with maximum 6 zone circuits. For a larger number of zones the ZCP is available
in a separate enclosure (extension module).
ZCP Series
Typical Specification: ZCP zone control stand-alone extension module
Zone Sensing Option
Supply and install Ready-Lite® ZCP Series Model ________________ of zone control panel. The equipment
shall have ______ (maximum 24) inputs for line voltage detection from different building zones. The wire
connection from each zone circuit shall be made with terminal blocks. The value of each zone voltage shall be:
____VAC. The output circuit shall be a dry-contact relay, normally closed and shall be accessible for connection
on a terminal block. The output circuit shall be connected at installation in series with the AC line supplying the
battery unit equipment. The value of output line voltage shall be: ____VAC. In the case of power failure of one
or several zones the output circuit will open and transfer the battery unit(s) in emergency lighting mode. When
specified the equipment shall include a ‘push to test’ push button and/or a pilot light for each zone circuit for
manual testing and service. The unit shall be certified CSA 22.2 No.141-10.
INTRODUCTION
The Ready-Lite® ZCP Zone Control Panel is
required in buildings where the path of
egress for emergency lighting crosses
through several areas and each area has a
separate electrical circuit and breaker for
lighting. In such circumstances a local
power failure in one area (zone) may not
trigger the emergency lighting connected
to a different electrical circuit.
The requirement for the zone control
function is specified in the National
Building Code of Canada and the
Canadian Electrical Code:
The unit shall be Ready-Lite® model: ________________________________________________________.
Typical Specification: battery unit equipment with ZCP zone control option
When specified, the equipment shall have ______ (maximum six) inputs for line voltage detection from different
building zones. The wire connection from each zone circuit shall be made with terminal blocks. The value
of each zone voltage shall be: _____VAC. In the case of a power failure of one or several zones the circuit will
transfer the battery unit to emergency lighting mode for minimum 30 minutes. When specified the equipment
shall include a ‘push to test’ push button and/or a pilot light for each zone circuit for manual testing and service.
The unit shall be certified CSA 22.2 No.141-10.
The unit shall be Ready-Lite® model: ______________________________________________________________.
• NBCC 9.9.12.3. 3) Lighting required in
Sentence (1) shall be designed to be
automatically actuated for a period of at
least 30 min when the electric lighting
in the affected area is interrupted.
• CEC C22.1-12 46-304 (4) Unit
equipment shall be installed in such
a manner that it will be automatically
actuated upon failure of the power
supply to the normal lighting in the
area covered by that unit equipment.
Typical wiring of stand-alone zcp zone sensing
lighting
cct
Electrical Panel
L1
L2
lighting
cct
lighting
cct
exit
cct
AC power for EM
Battery Unit
N
Control Wiring
for sensing
0.25A per zone
Zone Sensing ZCP
1. ordering information: stand-alone zone sensing extension module
AC output: battery unit(s)
(AC current draw: 8A max.)
U120= 120VAC input
U347= 347VAC input
Series
ZCP
Number of zone
circuits
1Z= 1 zone
2Z= 2 zones
3Z= 3 zones
AC input
of zones
Number of
units served
1= 120VAC
3= 347VAC
U1= 1 unit
Additional zone circuits
available, refer to cabinet
type.
Cabinet type
options
A= A cabinet (max. 4 circuits)
B= B cabinet (max. 9 circuits)
C= C cabinet (max. 24 circ. 120V; 18 circ. 347V)
IFG= fi berglass J1412HW (max.12 circuits)
PB*= z one(s) test
button
PL*= z one(s) pilot
lamp
*Only with cabinets:
A, B and C
E xample : U 1 2 0 Z C P 1 2 Z 1 U 1 C P B P L
2. ordering information: battery unit with internal zone sensing option
example
Unit AC input
MANDATORY for zcp
LDX242882RT9
U120= 120VAC
U347= 347VAC
options
zone sensing internal
ZCP= zone sensing
LDX Series p. 127
# of zones
1Z= 1 zone
2Z= 2 zones
3Z= 3 zones
Additional zone circuits (max. 6)
203
zone AC
Zone options
1= 120VAC
3= 347VAC
PB= z one(s) test button
PL= zone(s) pilot lamp
From wire guard charts to a full
warranty; we have all the coverage on
the technical information you need for
your emergency lighting.
wire size guide
P. 208
limited
warranty
P. 219
battery
capacity chart
P. 209
electrical
code
P. 210-212
building code
P. 213-217
fire code
P. 218
PRODUCT INDEX
P. 220
207
generator
room
P. 218
table
of
contents
When remote fixtures and exit signs are connected to emergency lighting units of less than 50 volts,
circuit runs must be sufficient size to maintain a proper operating voltage to all lamps. The maximum
allowable voltage drop should not exceed 5%. Proper wire size can be selected from the following table or
by use of the following formula:
CM=
Wire size in circular mills
CM = 22 x W x2 L
W=
Emergency load in watts
.05 x E
L= Length of circuit in feet
wire size guide
Length of Wire Run
volatge
6V
12V
24V
32V
48V
120V
wire
size
E= Line Voltage
22= Constant
.05= Factor for max. allowable
voltage drop
(in feet)
watts
13
18
25
30
35
50
12
41
30
21
18
15
11
10
65
47
32
28
24
17
8
110
75
54
45
39
27
6
165
120
86
71
62
43
60
75
100
150
200
250
300
400
9
8
6
4
-
-
-
-
14
11
9
6
-
-
-
-
22
18
14
9
7
-
-
-
36
29
22
15
11
9
-
-
12
165
110
85
71
61
42
35
29
21
14
10
8
-
-
10
260
190
136
112
97
68
52
45
34
23
17
21
18
-
8
415
300
215
180
154
108
90
72
54
36
27
21
18
-
6
660
475
340
285
245
170
140
114
86
57
43
34
28
-
4
1050
760
540
455
390
275
225
182
137
91
68
55
45
-
12
660
440
340
284
244
168
140
116
84
56
40
32
26
21
10
1040
760
544
448
388
272
208
180
136
92
68
52
44
34
8
1668
1200
860
720
616
432
360
288
216
144
108
84
72
54
6
24640
1900
1360
1140
1560
1100
900
728
548
364
272
220
180
100
4
4200
3040
2160
1810
1560
1100
900
728
548
364
272
220
180
100
12
1160
840
600
500
435
300
250
200
150
100
75
60
50
42
10
-
1340
960
800
690
480
400
32
24
160
120
96
80
63
8
-
-
1540
1280
1110
770
640
510
385
255
192
154
128
100
6
-
-
-
-
1740
1220
1020
815
610
405
305
240
200
163
260
4
-
-
-
-
-
-
1620
1300
970
650
485
390
325
12
-
1899
1367
1139
949
680
-
455
341
227
170
136
113
68
10
-
-
-
1811
1509
1085
-
724
543
362
271
217
181
108
8
-
-
-
-
-
1729
-
1152
864
576
432
345
288
172
6
-
-
-
-
-
-
-
1832
1374
926
687
549
458
274
12
14964
-
7792
-
-
3896
-
-
1945
1300
977
720
6550
608
10
23787
-
12367
-
-
6193
-
-
3093
2067
1553
1238
1033
966
8
37810
-
19705
-
-
9852
-
-
4820
3289
2471
1970
1644
1538
6
60159
-
331327
-
-
15663
-
-
7822
5229
3929
3132
2614
2445
208
battery unit
capacity chart
Battery Unit
volatge/wattage
Wattage capacity
30MIN
1H00
1H30
2H00
4H00
6V - 36W
36
21
15
12
6
6V - 72W
72
42
30
24
12
6V - 108W
108
63
45
36
18
6V - 180W
180
105
75
60
30
12V - 36W
36
21
15
12
6
12V - 72W
72
42
30
24
12
12V - 100W
100
58
42
33
17
12V - 144W
144
84
60
48
24
12V - 200W
200
117
83
67
33
12V - 250W
250
144
100
83
42
12V - 288W
288
168
120
96
48
12V - 360W
360
210
150
120
60
24V - 144W
144
84
60
48
24
24V - 200W
200
117
83
67
33
24V - 288W
288
168
120
96
48
24V - 350W
350
200
144
120
60
24V - 432W
432
250
180
144
72
24V - 550W
550
320
230
180
90
ldx series
ldx-i series
invislite ™ series
209
ldx-vq series
Section 46 — Emergency power supply, unit equipment, exit
signs, and life safety systems
46-000 Scope (see Appendix B)
Electrical Code
Extracts from the Canadian
Electrical Code 2010
1
This Section applies to the installation, operation, and maintenance of
(a) emergency power supply and unit equipment intended to provide power to life safety systems;
and
(b) emergency power supply and unit equipment intended to provide illumination of exit signs, in
theevent of failure of the normal supply, where the emergency power supply is required by the
National Building Code of Canada.
2
This Section applies to the wiring between the emergency power supply and life safety systems that
are required by the National Building Code of Canada to be provided with an emergency power
supply
3
This Section applies to the wiring of exit signs
4
The requirements of this Section supplement or amend the general requirements of this Code
46-002 Special terminology (see Appendix B)
In this Section, the following definitions apply:
Emergency power supply
Emergency power, supplied by a generator, batteries, or a combination there of, that is required by
the National Building Code of Canada.
Life safety systems
Emergency lighting and fire alarm systems that are required to be provided with anemergency
power supply from batteries, generators, or a combination thereof, and electrical equipment for
building services such as fire pumps, elevators, smoke-venting fans, smoke control fans, and
dampers that are required to be provided with an emergency power supply by an emergency
generator in conformance with the National Building Code of Canada.
Unit equipment
Unit equipment for emergency lighting conforming to CSA C22.2 No. 141.
General
46-100 Capacity
Emergency power supply and unit equipment shall have adequate capacity and rating to ensure the
satisfactory operation of all connected equipment when the principal source of power fails.
46-102 Instructions
1
Complete instructions for the operation and care of an emergency power supply or unit equipment
that shall specify testing at least once every month to ensure security of operation shall be posted
on the premises in a frame under glass.
2
The form of instructions and their locations shall be in compliance with the National Building Code
of Canada.
46-104 Maintenance
Where batteries are used as a source of the emergency power supply, the batteries shall be kept
(a) in proper condition; and
(b) fully charged at all times
46-106 Arrangement of lamps
1
Emergency lights shall be arranged so that the failure of any one lamp will not leave in total
darkness the area normally illuminated by it.
2
No appliance or lamp, other than those required for emergency purposes, shall be supplied by the
emergency circuits.
46-108 Wiring method (see Appendices B and G)
1
Except as permitted by Subrule (3), Rule 46-304(3), and Rule 46-400(2), the following conductors
shall be installed in accordance with Subrule (2):
(a) conductors required for operation of life safety systems and installed between an emergency
power supply and life safety systems;
(b) conductors between an emergency power supply and exit signs; and
(c) conductors between unit equipment and remote lamps.
210
2
Conductors described in Subrule (1) shall be
(a) installed in metal raceway of the totally enclosed type;
(b) incorporated in a cable having a metal armour or sheath;
(c) installed in rigid non-metallic conduit; or
(d) installed in electrical non-metallic tubing where embedded in at least 50 mm of masonry or
poured concrete.
3
Not with standing Subrule (2), conductors installed in buildings of combustible construction in
accordance with Rules 12-506 to 12-520 shall be permitted to be
(a) run as a non-metallic-sheathed cable; or
(b) installed in a totally enclosed non-metallic raceway.
4
Conductors installed in accordance with Subrule (1) shall be kept entirely independent of all
other conductors and equipment and shall not enter a luminaire, raceway, box, cabinet, or unit
equipment occupied by other conductors except where necessary
(a) in transfer switches; and
(b) in exit signs and emergency lights supplied from two sources.
5
Conductors between an emergency power supply and any electrical equipment that is not defined
as a “life safety system” in accordance with this Section shall not enter a luminaire, raceway, box,
or cabinet occupied by conductors installed as described in Subrule (1), except where necessary in
busways, splitters, and other similar enclosures provided for connection to the overcurrent device
for an emergency power supply described in Rule 46-208(1).
Emergency power supply
46-200 Emergency power supply (see Appendix B)
Rules 46-202 to 46-212 apply only to emergency power supply from central standby power sources.
46-202 Types of emergency power supply (see Appendix G)
1
The emergency power supply shall be a standby supply consisting of
(a) a storage battery of the rechargeable type having sufficient capacity to supply and maintain
at not less than 91% of full voltage the total load of the emergency circuits for the time period
required by the National Building Code of Canada, but in no case less than 30 min, and
equipped with a charging means to maintain the battery in a charged condition automatically;
or
(b) a generator.
2
Automobile batteries and lead batteries not of the enclosed glass-jar type are not considered
suitable under Subrule (1) and shall be used only where a deviation has been allowed in
accordance with Rule 2-030.
3
Where a generator is used, it shall be
(a) o f sufficient capacity to carry the load;
(b) arranged to start automatically without failure and without undue delay upon the failure of the
normal power supply to any transfer switch connected to this generator; and
(c) in conformance with CSA C282.
46-204 Protection of electrical conductors (see Appendices B and G)
All power, control, and communication conductors between an emergency generator as described in
Rule 46-202(3), and electrical equipment required to be installed as a part of the emergency power
supply and located outside the generator room shall be protected against fire exposure to provide
continued operation in compliance with the National Building Code of Canada.
46-206 Control
1
An emergency power supply shall be controlled by automatic transfer equipment that actuates the
emergency power supply upon failure of the normal current supply and that is accessible only to
authorized persons.
2
An automatic light-actuated device, approved for the purpose, shall be permitted to be used to
control separately the lights located in an area that is adequately illuminated during daylight hours
without the need for artificial lighting.
46-208 Overcurrent protection
1
The overcurrent device for an emergency power supply shall be coordinated with the overcurrent
devices of feeders and branch circuits supplying life safety systems and other electrical equipment
connected to the emergency power supply in order to provide selective operation of the branch
circuit overcurrent device when a fault occurs in that branch circuit.
2
The branch circuit overcurrent devices shall be accessible only to authorized persons.
211
Electrical Code
Extracts from the Canadian
Electrical Code 2010
46-210 Audible and visual trouble-signal devices
Electrical Code
Extracts from the Canadian
Electrical Code 2010
1
Every emergency power supply shall be equipped with audible and visual trouble-signal devices
that warn of derangement of the current source or sources and that indicate when exit signs or life
safety systems are supplied from the emergency power supply.
2
Audible trouble signals shall be permitted to be wired so that (a) they can be silenced, but a red
warning or trouble light shall continue to provide the protective function; and
(b) when the system is restored to normal, the audible signal will
(i) sound, indicating the need to restore the silencing switch to its normal position; or
(ii) reset automatically so as to provide sound for any subsequent operation of the emergency
power supply.
46-212 Remote lamps
Lamps shall be permitted to be mounted at some distance from the current supply that feeds them, but
the voltage drop in the wiring feeding such lamps shall not exceed 5% of the applied voltage.
Unit equipment
46-300 Unit equipment (see Appendix B)
Rules 46-302 to 46-306 apply to individual unit equipment for emergency lighting only.
46-302 Mounting of equipment
Each unit equipment shall be mounted with the bottom of the enclosure not less than 2 m above the
floor, wherever practicable.
46-304 Supply connections
Each unit equipment shall be mounted with the bottom of the enclosure not less than 2 m above the
floor, wherever practicable.
1
Receptacles to which unit equipment is to be connected shall be not less than 2.5 m above the
floor, where practicable, and shall be not more than 1.5 m from the location of the unit equipment.
2
Unit equipment shall be permanently connected to the supply if
(a) the voltage rating exceeds 250 V; or
(b) the marked input rating exceeds 24 A.
3
Where the ratings in Subrule (2) are not exceeded, the unit equipment shall be permitted to be
connected using the flexible cord and attachment plug supplied with the equipment.
4
Unit equipment shall be installed in such a manner that it will be automatically actuated upon
failure of the power supply to the normal lighting in the area covered by that unit equipment.
46-306 Remote lamps (see Appendix B)
1
The size of circuit conductors to remote lamps shall be such that the voltage drop does not exceed
5% of the marked output voltage of the unit equipment, or such other voltage drop for which the
performance of unit equipment is certified when connected to the specific remote lamp being
installed.
2
Remote lamps shall be suitable for remote connection and shall be included in the list of lamps
provided with the unit equipment.
3
The number of lamps connected to a single unit equipment shall not result in a load in excess
of the watts output rating marked on the equipment for the emergency period required by the
National Building Code of Canada, and the load shall be computed from the information in the list
of lamps referred to in Subrule (2).
Exit signs
46-400 Exit signs (see Appendices B and G)
1
Where exit signs are connected to an electrical circuit, that circuit shall be used for no other
purpose.
2
Notwithstanding Subrule (1), exit signs shall be permitted to be connected to a circuit supplying
emergency lighting in the area where these exit signs are installed.
3
Exit signs in Subrules (1) and (2) shall be illuminated by an emergency power supply where
emergency lighting is required by the National Building Code of Canada.
212
3.2.6 Requirements for High Buildings (See Appendix B)
3.2.6.1. Application
1
This Subsection applies to a building
a) o f Group A, D, E or F major occupancy classification that is more than
i) 3
6 m high, measured between grade and the floor level of the top storey, or
ii) 1
8 m high, measured between grade and the floor level of the top storey, and in which the
cumulative or total occupant load on or above any storey above grade, other than the first storey,
divided by 1.8 times the width in metres of all exit stairs at that storey, exceeds 300,
b) containing a Group B major occupancy in which the floor level of the highest storey of that major
occupancy is more than 18 m above grade,
c) c ontaining a floor area or part of a floor area located above the third storey designed or intended as
a Group B, Division 2 or 3 occupancy, or
d) c ontaining a Group C major occupancy whose floor level is more than 18 m above grade.
3.2.7.3. Emergency Lighting
1
Emergency lighting shall be provided to an average level of illumination not less than 10 lx at floor or
tread level in
a) exits
b) p
rincipal routes providing access to exit in open floor areas and in service rooms,
c) corridors used by the public,
d) corridors serving sleeping rooms in a treatment occupancy,
e) c orridors serving sleeping rooms in a care occupancy, except corridors serving sleeping rooms
within individual suites of care occupancy,
f) corridors serving classrooms,
g) underground walkways,
h) public corridors,
I) floor areas or parts thereof where the public may congregate
i) in Group A, Division 1 occupancies, or
ii) in Group A, Division 2 and 3 occupancies having an occupant load of 60 or more,
j) fl oor areas or parts thereof of daycare centreswhere persons are cared for, and
k) food preparation areas in commercial kitchens.
2
Emergency lighting to provide an average level of illumination of not less than 10 lx at floor or catwalk
level shall be included in a service space referred to in Sentence 3.2.1.1.(8).
3
The minimum value of the illumination required by Sentences (1) and (2) shall be not less than 1 lx.
4
In addition to the requirements of Sentences (1) to (3), the installation of battery-operated emergency
lighting in buildings or part thereof where treatment is provided shall conform to the appropriate
requirements of CSA Z32, “Electrical Safety and Essential Electrical Systems in Health Care Facilities”.
3.2.7.4. Emergency Power for Lighting
1
An emergency power supply shall be
a) p
rovided to maintain the emergency lighting required by this Subsection from a power source such
as batteries or generators that will continue to supply power in the event that the regular power
supply to the building is interrupted, and
b) s o designed and installed that upon failure of the regular power it will assume the electrical load
automatically for a period of
i) 2 h for a building within the scope of Subsection 3.2.6.,
ii) 1
h for a building of Group B major occupancy classification that is not within the scope of
Subsection 3.2.6., and
iii) 30 min for a building of any other occupancy. (See Appendix A.)
2
If self-contained emergency lighting units are used, they shall conform to CSA C22.2 No. 141,
“Emergency Lighting Equipment.”
3.2.7.5. Emergency Power Supply Installation
1
Except as required by Articles 3.2.7.6. and 3.2.7.7., an emergency electrical power supply system
shall be installed in conformance with CAN/CSA-C282, “Emergency Electrical Power Supply for
Buildings.” (See Sentence 3.2.7.8.(1) for emergency electrical power supply for voice communication
systems).
213
Building Code
Extracts from the National Building
Code of Canada 2010
3.4.5. Exit Signs
3.4.5.1. Exit Signs
1
Building Code
2
Extracts from the National Building
Code of Canada 2010
3
4
Every exit door shall have an exit sign placed over or adjacent to it if the exit
serves
a) a building more than 2 storeys in building height,
b) a building having an occupant load of more than 150, or
c) a room or floor area that has a fire escape as part of a required means of egress
Every exit sign shall
a) be visible on approach to the exit,
b) except as permitted in Sentence (3), consist of a green pictogram and a white or lightly tinted
graphical symbol meeting the colour specifications referred to in ISO 3
864-1, “Graphical symbols – Safety colours and safety
signs – Part 1: Design principles for safety signs in workplaces and public areas,” and
c) conform to the dimensions indicated in ISO 7010, “Graphical symbols – Safety colours and safety
signs – Safety signs used in workplaces and public areas,” for the following symbols (see Appendix
A):
i) E001 emergency exit left,
ii) E002 emergency exit right,
iii) E005 90-degree directional arrow, and
iv) E006 45-degree directional arrow
Internally illuminated exit signs shall be continuously illuminated and
a) where illumination of the sign is powered by an electrical circuit, be constructed in conformance
with CSA C22.2 No. 141, “Emergency Lighting Equipment,” or
b) where illumination of the sign is not powered by an electrical circuit, be constructed in conformance with CAN/ULC-S572, “Photoluminescent and Self-Luminous Signs and Path Marking
Systems.”
Externally illuminated exit signs shall be continuously illuminated and be constructed in conformance
with CAN/ULC-S572, “Photoluminescent and Self-Luminous Signs and Path Marking Systems.” (See
Appendix A.)
5
The circuitry serving lighting for externally and internally illuminated exit signs shall
a) serve no equipment other than emergency equipment, and
b) be connected to an emergency power supply as described in Article 3.2.7.4.
6
Where no exit is visible from a public corridor, from a corridor used by the public in a Group A or B
major occupancy, or from principal routes serving an open floor area having an occupant load of more
than 150, an exit sign conforming to Clauses (2)(b) and (c) with an arrow or pointer indicating the
direction of egress shall be provided.
7
Except for egress doorways described in Sentence 3.3.2.4.(4), an exit sign conforming to Sentences
(2) to (5) shall be placed over or adjacent to every egress doorway from rooms with an occupant load
of more than 60 in Group A, Division 1 occupancies, dance halls, licensed beverage establishments,
and other similar occupancies that, when occupied, have lighting levels below that which would
provide easy identification of the egress doorway.
3.4.5.2. Signs for Stairs and Ramps at Exit Level
1
In a building more than 2 storeys in building height, any part of an exit ramp or stairway that
continues up or down past the lowest exit level shall have a posted sign clearly indicating that it does
not lead to an exit.
9.9.11. Signs
9.9.11.1. Application
1
This Subsection applies to all exits except those serving not more than one dwelling unit or a house
with a secondary suite.
9.9.11.2. Visibility of Exits
1
Exits shall be located so as to be clearly visible or their locations shall be clearly indicated.
9.9.11.3. Exit Signs
1
Every exit door shall have an exit sign placed over it or adjacent to it if the exit serves
a) a building that is 3 storeys in building height,
b) a building having an occupant load of more than 150, or
c) a room or floor area that has a fire escape as part of a required means of egress.
214
2
Every exit sign shall
a) be visible on approach to the exit,
b) e xcept as permitted in Sentence (3), consist of a green pictogram and a white or lightly tinted
graphical symbol meeting the colour specifications referred to in ISO 3864-1, “Graphical symbols –
Safety colours and safety signs – Part 1: Design principles for safety signs in workplaces and public
areas,” and
c) c onform to the dimensions indicated in ISO 7010, “Graphical symbols – Safety colours and safety
signs – Safety signs used in workplaces and public areas,” for the following symbols
(see A-3.4.5.1.(2)(c) in Appendix A):
i) E001 emergency exit left,
ii) E002 emergency exit right,
iii) E005 90-degree directional arrow, and
iv) E006 45-degree directional arrow.
3
Internally illuminated exit signs shall be continuously illuminated and
a) w
here illumination of the sign is powered by an electrical circuit, be constructed in conformance
with CSA C22.2 No. 141, “Emergency Lighting Equipment,” or
b) w
here illumination of the sign is not powered by an electrical circuit, be constructed in conformance with CAN/ULC-S572, “Photoluminescent and Self-Luminous Signs and Path Marking
Systems.”
4
Externally illuminated exit signs shall be continuously illuminated and be constructed in conformance
with CAN/ULC-S572, “Photoluminescent and Self-Luminous Signs and Path Marking Systems.” (See
A-3.4.5.1.(4) in Appendix A.)
5
The circuitry serving lighting for externally and internally illuminated exit signs shall
a) serve no equipment other than emergency equipment, and
b) be connected to an emergency power supply as described in Sentences 9.9.12.3.(2), (3) and (7).
6
Where no exit is visible from a public corridor, from a corridor used by the public, or from principal
routes serving an open floor area having an occupant load of more than 150, an exit sign conforming
to Clauses (2)(b) and (c) with an arrow or pointer indicating the direction of egress shall be provided
9.9.11.4. Signs for Stairs and Ramps at Exit Level
1
In buildings that are 3 storeys in building height, any part of an exit ramp or stairway that continues
up or down past the lowest exit level shall be clearly marked to indicate that it does not lead to an exit,
if the portion beyond the exit level may be mistaken as the direction of exit travel.
9.9.12. Lighting
9.9.11.4. Signs for Stairs and Ramps at Exit Level
1
This Subsection applies to the lighting of all means of egress except those within dwelling units or a
house with a secondary suite.
9.9.12.2. Required Lighting in Egress Facilities
1
Every exit, public corridor or corridor providing access to exit for the public shall be equipped to
provide illumination to an average level of not less than 50 lx at floor or tread level and at all points
such as angles and intersections at changes of level where there are stairs or ramps.
2
The minimum value of the illumination required by Sentence (1) shall be not less than 10 lx
9.9.12.3. Emergency Lighting
1
Emergency lighting shall be provided in
a) exits,
b) principal routes providing access to exit in an open floor area,
c) corridors used by the public,
d) underground walkways, and
e) public corridors.
2
Emergency lighting required in Sentence (1) shall be provided from a source of energy separate from
the electrical supply for the building.
3
Lighting required in Sentence (1) shall be designed to be automatically actuated for a period of at
least 30 min when the electric lighting in the affected area is interrupted.
4
Illumination from lighting required in Sentence (1) shall be provided to average levels of not less than
10 lx at floor or tread level.
5
The minimum value of the illumination required by Sentence (4) shall be not less than 1 lx.
6
Where incandescent lighting is provided, lighting equal to 1 W/m2 of floor area shall be considered to
meet the requirement in Sentence (4).
7
Where self-contained emergency lighting units are used, they shall conform to CSA C22.2 No. 141,
“Emergency Lighting Equipment.”
215
Building Code
Extracts from the National Building
Code of Canada 2010
aPPENDIX A
explanatory MATERIAL
Building Code
A-3.1.2. Use Classification
The purpose of classification is to determine which requirements apply.
This Code requires classification in accordance with every major occupancy for which the building is used
or intended to be used. Where necessary, an application clause has been inserted in this Part to explain
how to choose between the alternative requirements which multiple occupancy classification may present.
A-3.1.2.1.(1) Major Occupancy Classification.
The following are examples of the major occupancy classifications described in Table 3.1.2.1.:
Extracts from the National Building
Code of Canada 2010
EXAMPLES
Motion picture theatres
Opera houses
Television studios admitting a viewing audience
Theatres, including experimental theatres
Art galleries
Auditoria
Bowling alleys
Churches and similar places of worship
Clubs, nonresidential
Community halls
Courtrooms
Dance halls
Exhibition halls (other than classified in Group E)
Gymnasia
Lecture halls
Libraries
Licensed beverage establishments
Museums
Passenger stations and depots
Recreational piers
Restaurants
Schools and colleges, nonresidential
Undertaking premises
Arenas
Indoor swimming pools, with or without spectator seating
Rinks
GROUP
DIVISION
A
1
A
2
A
3
Amusement park structures (not elsewhere classified)
Bleachers
Grandstands
Reviewing stands
Stadiums
A
4
Jails
Penitentiaries
Police stations with detention quarters
Prisons
Psychiatric hospitals with detention quarters
Reformatories with detention quarters
B
1
Care facilities with treatment
Convalescent /recovery/rehabilitation centres with
treatment
Hospices with treatment
Hospitals
Infirmaries
Nursing homes with treatment
Psychiatric hospitals without detention quarters
Respite centres with treatment
B
2
Assisted/supportive living facilities
Care facilities without treatment
Children’s custodial homes
Convalescent/recovery/rehabilitation centres without
treatment
Group homes
Hospices without treatment
Nursing homes without treatment
Reformatories without detention quarters
Respite centres without treatment
B
3
Apartments
Boarding houses
Clubs, residential
Colleges, residential
Convents
Dormitories
Hotels
Houses
Lodging houses
Monasteries
Motels
Schools, residential
C
216
A-3.4.5.1.(2)(c) Graphical Symbols for Exit Signs ISO 7010,
“Graphical” symbols – Safety colours
and safety signs – Safety signs used in workplaces and public areas,” identifies the following internationally recognized symbols for use at required exits
“Emergency exit RIGHT” (E001) symbol from ISO 7010 Figure
A-3.4.5.1.(2)(c)-B 90-degree directional arrow (E005) from
ISO 7010
A-3.4.5.1.(4) Externally Illuminated Signs
An external lighting source is required to properly charge photoluminescent signs. These types of signs
must be lit in conformance with the charging requirements stated in CAN/ULC-S572.
A-3.4.6. Application to Means of Egress
The requirements in Subsection 3.4.6. apply to interior and exterior exits, as well as to ramps, stairways
and passageways used by the public as access to exit. The treads, risers, landings, handrails and guards
for the latter access to exit facilities must thus be provided in conformance with the appropriate
requirements for exit facilities.
EXAMPLES
Building Code
Extracts from the National Building
Code of Canada 2010
GROUP
DIVISION
Banks
Barber and hairdressing shops
Beauty parlours
Dental offices
Dry cleaning establishments, self-service, not using
flammable or explosive solvents or cleaners
Laundries, self-service
Medical offices
Offices
Police stations without detention quarters
Radio stations
Small tool and appliance rental and service
establishments
D
Department stores
Exhibition halls
Markets
Shops
Stores
Supermarkets
E
Bulk plants for flammable liquids
Bulk storage warehouses for hazardous substances
Cereal mills
Chemical manufacturing or processing plants
Distilleries
Dry cleaning plants
Feed mills
Flour mills
Grain elevators
Lacquer factories
Mattress factories
Paint, varnish and pyroxylin product factories
Rubber processing plants
Spray painting operations
Waste paper processing plants
F
1
Aircraft hangars
Box factories
Candy plants
Cold storage plants
Dry cleaning establishments not using flammable or
explosive solvents or cleaners
Electrical substations
Factories
Freight depots
Helicopter landing areas on roofs
Laboratories
Laundries, except self-service
Mattress factories
Planing mills
Printing plants
Repair garages
Salesrooms
Service stations
Storage rooms
Television studios not admitting a viewing audience
Warehouses
Wholesale rooms
Woodworking factories
Workshops
F
2
Creameries
Factories
Laboratories
Light-aircraft hangars (storage only)
Power plants
Salesrooms
Sample display rooms
Storage garages, including open air parking
garages
Storage rooms
Warehouses
Workshops
F
3
217
2.7. Safety to Life
2.7.3. Exit Lighting, Exit Signs and Emergency Lighting
Fire Code
Extracts from the National Fire
Code of Canada 2010
generator room
Extracts from the Canadian Standards
Association C282-09
2.7.3.1. Installation and Maintenance
1) Exit lighting, exit signs and emergency lighting shall be provided in buildings in conformance
with the NBC. (See Appendix A.)
2) Exit lighting and exit signs shall be illuminated during times when the building is occupied.
3) Emergency lighting shall be maintained in operating condition, in conformance with Section 6.5.
6.5. Emergency Power Systems and Unit Equipment for Emergency Lighting
5.1.1. Inspection, Testing and Maintenance
1) Except as provided in Articles 6.5.1.2. to 6.5.1.5., emergency power systems shall be inspected,
tested and maintained in conformance with CAN/CSA-C282, “Emergency Electrical Power
Supply for Buildings.”
2) An emergency electrical power supply system for emergency equipment for health care facilities
shall be inspected, tested and maintained in conformance with CSA Z32, “Electrical Safety and
Essential Electrical Systems in Health Care Facilities.” (See Appendix A.)
6.5.1.2. Notification
1) When an emergency power system or any part thereof is shut down, the supervisory staff shall
be notified in conformance with Section 2.8.
6.5.1.3. Instructions
1) Where an emergency power system is installed, instructions shall be provided for switching on
essential loads and for starting the generator when this is not done automatically.
6.5.1.4. Records
1) Written records shall be maintained as required in CAN/CSA-C282, “Emergency Electrical Power
Supply for Buildings”.
6.5.1.6. Inspection of Unit Equipment
1) Self-contained emergency lighting unit equipment shall be inspected at intervals not greater
than one month to ensure that
a) pilot lights are functioning and not obviously damaged or obstructed,
b) the terminal connections are clean, free of corrosion and lubricated when necessary,
c) the terminal clamps are clean and tight as per manufacturer’s specifications, and
d) the battery surface is kept clean and dry.
2) Self-contained emergency lighting unit equipment shall be tested
a) at intervals not greater than one month to ensure that the emergency lights will function upon
failure of the primary power supply, and
b) at intervals not greater than 12 months to ensure that the unit will provide emergency lighting
for a duration equal to the design criterion under simulated power failure conditions.
3) After completion of the test required in Clause (2)(b), the charging conditions for voltage and
current and the recovery period shall be tested to ensure that the charging system is functioning
in accordance with the manufacturer’s specifications.
Generator room
Section 6.11
Emergency Lighting
6.11.1
The emergency electrical power supply room and the automatic transfer switch room, where
separate, shall be equipped with unit equipment for emergency lighting that complies with CSA
C22.2 No. 141. Sufficient lamps shall be provided to ensure that a minimum lighting level of 50 lx
for 2 h is available at all equipment locations requiring adjustment or service.
Note: This illumination level is significantly greater than that specified in the NBCC, which requires 10 lx for egress route
emergency lighting
6.11.2
Emergency lighting units shall be tested in accordance with Table 2 and CSA C22.2 No. 141.
6.11.3
The emergency lighting unit shall include
(a) automatic self-diagnostic circuitry; and
(b) a transient voltage surge suppressor on the supply side of power to the unit.
218
warranty
1.1
Ready-Lite® emergency lighting equipment units (excluding AC and DC Central Systems,
lamps, pilot lights and fuses) are fully warranted to be free of defects in material and
workmanship under normal use for a period of one (1) year. Ready-Lite® emergency lighting
equipment units with the NEXUS® option are fully warranted to be free of defects in material
and workmanship under normal use for a period of five (5) years. The full warranty period
begins on the date of installation or ninety (90) days from the date of shipment, whichever
date is earlier.
1.2
DC and AC Central Systems are covered by a separate comprehensive warranty.
1.3
LED strips used in Ready-Lite® Exit and Pictogram signs are warranted to be free of defects
in material and workmanship under normal use for a period of ten (10) years. MR16 LED
lamps are warranted to be free of defects in material and workmanship under normal use for
a period of five (5) years when purchased and used with Ready-Lite® Battery Units,
Combination Units or Remotes. The full warranty period begins on the date of installation or
ninety (90) days from the date of shipment, whichever date is earlier.
1.4
Ready-Lite® unit equipment batteries are warranted to be free of defects in material and
workmanship under normal use for a period of one (1) year full and nine (9) years Pro Rata.
The full warranty period begins on the date of installation or ninety (90) days from the date
of shipment, whichever date is earlier. Batteries have a maximum storage life (shelf life) of 6
months. Batteries must be recharged or placed in service within the 6 months storage life or
battery warranty will be void.
2.1
Should defect appear in the equipment or batteries listed in the paragraph 1.1, 1.2, 1.3
or 1.4 above within the specified full warranty period, Ready-Lite® will repaid or replace
equipment without charge (see paragraph 3.4). Such repair or replacement shall be the
purchaser’s exclusive remedy.
2.2
The Pro Rata Warranty period for batteries begins on the date the full warranty ends.
2.3
A battery determined to be defective during the Pro Rata Warranty Period shall be repaired
or replaced at a cost equal to the net price in effect at the time, reduced by the percentage
obtained in multiplying 10% by the number of full years remaining in the total warranty
period. Such repair or replacement at this adjusted price shall be the purchaser’s exclusive
remedy.
3.1
All warranties are subject to proper installation and maintenance in accordance with the
instructions supplied.
3.2
Any material deemed defective must be returned freight prepaid, to a service depot for
evaluation (see paragraph 5.1). Any changes in circuitry or components by other than an
authorized Ready-Lite® personnel or its service companies will void the warranty.
3.3
All warranties are limited to the repair and/or replacement of parts or equipment, which,
upon examination at our service depot, are determined to be defective and in our judgment
are subject to repair or replacement under warranty. Replacement of lamps, pilot lights, and
fuses with exception of MR16 LED lamps is not included in the warranty.
3.4
If new replacement parts are shipped before defective goods are received for evaluation, the
replacement parts will be invoiced at the net price in effect at the time. These charges will be
credited if, upon receipt and evaluation of goods, a defect is determined. Only replacement
parts will be shipped under these circumstances, if field replacement is possible. Ready-Lite®
factory only reserves the right to ship new unit equipment for replacement purposes. Unit
returned after installation cannot be restored to 100% saleable condition.
4.1
In no event shall Ready-Lite® be liable for back charges of any kind, including without
limitation, labor charges for field repair or late penalties.
4.2
This warranty does not cover damages caused by abuse, improper maintenance or
installation or damage due to installation areas with other than normal temperatures
and environmental conditions per application specifications. Ready-Lite® assumes no
responsibility for any damages to people, property, apparatus or otherwise resulting from
improper installation or maintenance of its emergency lighting unit equipment.
4.3
This warranty does not cover damages caused by abuse, fire or act of God.
4.4
In no event shall Ready-Lite® be liable for incidental or consequential damages.
4.5
The foregoing warranty is in lieu of other warranties, expressed or implied. Except as stated
in this warranty, Ready-Lite® shall not be liable for any defects in, or breach of any contract
relating to, the quality of performance of Ready-Lite® equipment under any theory of law
including, without limitation, contract, negligence, strict liability or misrepresentation.
4.6
Ready-Lite® warranty coverage shall not apply to any equipment of another manufacturer
used in conjunction with Ready-Lite® equipment.
5.1
Defective goods returned to the factory must be shipped prepaid. Any and all collect returned
shipments will be refused. Freight charges to return repaired equipment or ship replacement
equipment to the purchaser to be paid by Ready-Lite® . Factory will return repaired or
replacement goods via same shipping method as received whenever possible and practical.
219
Limited Warranty
Product index
Series . . . . . . . . . PAGE #
12H10 . . . . . . . . . . . . 57
12H5 . . . . . . . . . . . . . 57
12L50. . . . . . . . . . . . . 57
12R50. . . . . . . . . . . . .49
12R80. . . . . . . . . . . . .49
AVNG20N. . . . . . . . . 106
AVNG36N. . . . . . . . . 106
B29 . . . . . . . . . . . . . 125
C29. . . . . . . . . . . . . . 116
CAD . . . . . . . . . . . . . 103
CAD24AC . . . . . . . . . 147
CADAC. . . . . . . . . . . 147
CADACDC. . . . . . . . . 147
CADDC. . . . . . . . . . . 147
CNESTU. . . . . . . . . . . 44
CNEXTN. . . . . . . . . . . 45
CNSXTN. . . . . . . . . . . 45
CS2100U . . . . . . . . . . 27
CS2200U . . . . . . . . . . 27
CS4000. . . . . . . . . 29, 30
CS4100. . . . . . . . . 29, 30
CS4100E. . . . . . . . . . . 29
CS4200. . . . . . . . . 29, 30
CS4200E. . . . . . . . . . . 29
CS5100. . . . . . . . . . . . 33
CS5200. . . . . . . . . . . . 33
CS7100. . . . . . . . . . . . 37
CS7200. . . . . . . . . . . . 37
CS9100N . . . . . . . 58, 59
CS9200N . . . . . . . 58, 59
CSL. . . . . . . . . . . . . . . 23
CSL3100. . . . . . . . . . . 22
CSL3100R. . . . . . . . . . 22
CSL3200. . . . . . . . . . . 22
CX2100U . . . . . . . . . . 26
CX2200U . . . . . . . . . . 26
CX4000. . . . . . . . . 28, 30
CX4100. . . . . . . . . 28, 30
CX4100E. . . . . . . . . . . 28
CX4200. . . . . . . . . 28, 30
CX4200E. . . . . . . . . . . 28
CX5100. . . . . . . . . . . . 32
CX51002S. . . . . . . . . . 34
CX51003S. . . . . . . . . . 34
CX5200. . . . . . . . . . . . 32
CX55000R. . . . . . . . . .35
CX7100. . . . . . . . . . . . 37
CX7200. . . . . . . . . . . . 37
CX9100N . . . . . . . . . . 59
CX9200N . . . . . . . . . . 59
CXL. . . . . . . . . . . . . . . 23
CXL3100. . . . . . . . . . . 24
CXL3200. . . . . . . . . . . 24
FEB . . . . . . . . . . . . . 197
FEB25. . . . . . . . . . . .138
FEB50. . . . . . . . . . . .138
FEB80. . . . . . . . . . . .138
GUA. . . . . . . . . . . . . 152
H12H10 . . . . . . . . . . . 73
H12Z60 . . . . . . . . . . . 73
HIDE. . . . . . . . . . . . . 104
HIDR . . . . . . . . . . . . 150
HZ36N. . . . . . . . . . . . 73
IPR. . . . . . . . . . . . . . 137
L20. . . . . . . . . . . . . . . 57
L50. . . . . . . . . . . . . . . 57
LD12110. . . . . . . . 50, 51
LD12144. . . . . . . . 50, 51
LD12250. . . . . . . . 50, 51
Series . . . . . . . . . PAGE #
LD12360 . . . . . . . 50, 51
LD6-36IF. . . . . . . . . . . 61
LD6-36IF2. . . . . . . . . . 61
LD6-72IF. . . . . . . . . . . 61
LD6-72IF2. . . . . . . . . . 61
LDX12. . . . . . . 81, 83, 85
LDX12-100. . . . 109, 127
LDX12-100IFG . . . . . 133
LDX12-100ISC. . . . . . 133
LDX12-100ITC. . . . . . 133
LDX12-100NX. . . . . . 135
LDX12-100T. . . . . . . 113
LDX12-108NM . . . . . 129
LDX12-120HZ. . . . . . 131
LDX12-144. . . . 104, 127
LDX12-144IFG . . . . . 133
LDX12-144ISC. . . . . . 133
LDX12-144ITC. . . . . . 133
LDX12-144NX. . . . . . 135
LDX12-144T. . . . . . . 113
LDX12-144VQ. . . . . . 111
LDX12-150HZ. . . . . . 131
LDX12-200IFG . . . . . 133
LDX12-200ISC. . . . . . 133
LDX12-200ITC. . . . . . 133
LDX12-200NX. . . . . . 135
LDX12-200VQ. . . . . . 111
LDX12-216. . . . 109, 127
LDX12-216T. . . . . . . 113
LDX12-250. . . . 109, 127
LDX12-250IFG . . . . . 133
LDX12-250ISC. . . . . . 133
LDX12-250ITC. . . . . . 133
LDX12-250NX. . . . . . 135
LDX12-288VQ. . . . . . 111
LDX12-36. . . . . . . . . 127
LDX12-360. . . . 109, 127
LDX12-360IFG . . . . . 133
LDX12-360ISC. . . . . . 133
LDX12-360ITC. . . . . . 133
LDX12-360NX. . . . . . 135
LDX12-36HZ. . . . . . . 131
LDX12-36IFG . . . . . . 133
LDX12-36ISC. . . . . . . 133
LDX12-36ITC. . . . . . . 133
LDX12-36NM . . . . . . 129
LDX12-36T. . . . . . . . 113
LDX12-36TS. . . . . . . 115
LDX12-36VQ. . . . . . . 111
LDX12-72. . . . . 109, 127
LDX12-72HZ. . . . . . . 131
LDX12-72IFG . . . . . . 133
LDX12-72ISC. . . . . . . 133
LDX12-72ITC. . . . . . . 129
LDX12-72NX. . . . . . . 135
LDX12-72T. . . . . . . . 113
LDX12-72TS. . . . . . . 115
LDX12-72VQ. . . . . . . 111
LDX24. . . . . . . 81, 83, 85
LDX24-144. . . . 109, 127
LDX24-144IFG . . . . . 113
LDX24-144ISC. . . . . . 133
LDX24-144ITC. . . . . . 133
LDX24-144NX. . . . . . 135
LDX24-144T. . . . . . . 113
LDX24-144VQ. . . . . . 111
LDX24-200. . . . 109, 127
LDX24-288. . . . 109, 127
LDX24-288IFG . . . . . 133
Series . . . . . . . . . PAGE #
LDX24-288ISC. . . . . . 133
LDX24-288ITC. . . . . . 133
LDX24-288NX. . . . . . 135
LDX24-288T. . . . . . . 113
LDX24-288VQ. . . . . . 111
LDX24-350. . . . 109, 127
LDX24-350IFG . . . . . 133
LDX24-432ISC. . . . . . 133
LDX24-350ITC. . . . . . 133
LDX24-350NX. . . . . . 135
LDX24-432. . . . 109, 127
LDX24-432IFG . . . . . 133
LDX24-432ISC. . . . . . 133
LDX24-432ITC. . . . . . 133
LDX24-432NX. . . . . . 135
LDX24-550. . . . 109, 127
LDX24-550IFG . . . . . 133
LDX24-550ISC. . . . . . 133
LDX24-550ITC. . . . . . 133
LDX24-720. . . . 109, 127
LDX24-720IFG . . . . . 133
LDX24-720ISC. . . . . . 133
LDX24-720ITC. . . . . . 133
LDX6. . . . . . . . 81, 83, 85
LDX6-108. . . . . 109, 127
LDX6-108IFG . . . . . . 133
LDX6-108ISC. . . . . . . 133
LDX6-108ITC. . . . . . . 133
LDX6-108NM . . . . . . 129
LDX6-108NX. . . . . . . 135
LDX6-108T. . . . . . . . 113
LDX6-120HZ. . . . . . . 131
LDX6-144VQ. . . . . . . 111
LDX6-150HZ. . . . . . . 131
LDX6-180. . . . . 109, 127
LDX6-180IFG . . . . . . 133
LDX6-180ISC. . . . . . . 133
LDX6-180ITC. . . . . . . 133
LDX6-180NX. . . . . . . 135
LDX6-180T. . . . . . . . 113
LDX6-180VQ. . . . . . . 111
LDX6-36. . . . . . 109, 127
LDX6-36HZ. . . . . . . . 131
LDX6-36IFG . . . . . . . 133
LDX6-36ISC. . . . . . . .133
LDX6-36ITC. . . . . . . .133
LDX6-36NM . . . . . . . 129
LDX6-36T. . . . . . . . . 113
LDX6-36VQ. . . . . . . . 111
LDX6-72. . . . . . 109, 127
LDX6-72HZ. . . . . . . . 131
LDX6-72IFG . . . . . . . 133
LDX6-72ISC. . . . . . . .133
LDX6-72ITC. . . . . . . .133
LDX6-72-NM. . . . . . . 129
LDX6-72NX. . . . . . . . 135
LDX6-72T. . . . . . . . . 113
LDX6-72VQ. . . . . . . . 111
LDXA12-44. . . . . . . . 121
LDXA12-72. . . . . . . . 121
LDXA6-27. . . . . . . . . 121
LDXA6-44. . . . . . . . . 121
LDXA6-72. . . . . . . . . 121
LDXC12-44. . . . . . . . 119
LDXC12-72. . . . . . . . 119
LDXC6-27. . . . . . . . . 119
LDXC6-44. . . . . . . . . 119
LDXC6-72. . . . . . . . . 119
LES18P. . . . . . . . . . . 124
220
Series . . . . . . . . . PAGE #
LH . . . . . . . . . . . . . . 155
LQ . . . . . . . . . . . . . . 155
LS. . . . . . . . . . . . . . . 155
LT. . . . . . . . . . . . . . . 155
MB. . . . . . . . . . . . . . . 89
MB1. . . . . . . . . . . . . 193
MB2. . . . . . . . . . . . . 193
MB3. . . . . . . . . . . . . 193
MB4. . . . . . . . . . . . . 193
MH. . . . . . . . . . . . . . 105
MHG. . . . . . . . . . . . . 151
N12M60. . . . . . . . . . . 67
NEXTN. . . . . . . . . . . . 43
NM36. . . . . . . . . . . . . 67
NMM . . . . . . . . . . . . 161
NMMHZ . . . . . . . . . . 164
P1R . . . . . . . . . . 91, 195
P2R . . . . . . . . . . 91, 195
P3R . . . . . . . . . . 91, 195
P4R . . . . . . . . . . 91, 195
R1 . . . . . . . . . . . . . . 177
R2 . . . . . . . . . . . . . . 177
R27 . . . . . . . . . . . . . . 49
R3 . . . . . . . . . . . . . . 177
R4 . . . . . . . . . . . . . . 177
R50 . . . . . . . . . . . . . . 49
RA1 . . . . . . . . . . . . . . 31
RA2 . . . . . . . . . . . . . . 31
RA3 . . . . . . . . . . . . . . 31
RAC . . . . . . . . . . . . . . 39
RAE1 . . . . . . . . . . . . . 18
RAEA . . . . . . . . . . . . . 18
RAEL . . . . . . . . . . . . . 18
RAER . . . . . . . . . . . . . 18
RCSB . . . . . . . . . . . . 117
RCSC . . . . . . . . . . . . . 55
RCS-ISP . . . . . . . . . . . 54
RCS-LU. . . . . . . . . . . . 54
RCSR . . . . . . . . . . . . 148
RDE1 . . . . . . . . . . . . . 15
RDEA . . . . . . . . . . . . . 15
RDEL . . . . . . . . . . . . . 15
RDER. . . . . . . . . . . . . 15
RF105. . . . . . . . . . . .153
RFX-CSDF. . . . . . . . . . 79
RFX-CSSF. . . . . . . . . . 79
RFX-EXDF. . . . . . . . . . 77
RFX-EXSF. . . . . . . . . . 77
RFXQ . . . . . . . . . . . . 165
RFXQ1 . . . . . . . . . . . 165
RFXQ-P2. . . . . . . . . . 165
RH1G. . . . . . . . . . . . . 68
RH2G. . . . . . . . . . . . . 68
RHCG. . . . . . . . . . . . . 71
RIB12. . . . . . . . . . . . 197
RIB120. . . . . . . . . . . 197
RIB24. . . . . . . . . . . . 197
RIB32. . . . . . . . . . . . 197
RIB48. . . . . . . . . . . . 197
RIB6. . . . . . . . . . . . . 197
RIII. . . . . . . . . . . . . . 179
RL120. . . . . . . . . . . . 186
RL150. . . . . . . . . . . . 156
RL24. . . . . . . . . . . . . 186
RL25. . . . . . . . . . . . . 159
RL36. . . . . . . . . . . . . 186
RL40M. . . . . . . . . . . 149
RL40MP. . . . . . . . . . 149
RL4120. . . . . . . . . . . 183
RL4208. . . . . . . . . . . 183
Series . . . . . . . . . PAGE #
RL4240. . . . . . . . . . . 183
RL4277. . . . . . . . . . . 183
RL4347. . . . . . . . . . . 183
RL4600. . . . . . . . . . . 183
RLBD . . . . . . . . . . . . 194
RLBH. . . . . . . . . . . . 194
RLR . . . . . . . . . . . . . 157
RLR2 . . . . . . . . . . . . 107
RM. . . . . . . . . . . . . . 154
RN1 . . . . . . . . . . . . . . 62
RN2 . . . . . . . . . . . . . . 62
RNC1. . . . . . . . . . . . . 65
RNC2. . . . . . . . . . . . . 65
RP1 . . . . . . . . . . . . . . 52
RP2 . . . . . . . . . . . . . . 52
RP3 . . . . . . . . . . . . . . 52
RQ . . . . . . . . . . . . . . 154
RS1 . . . . . . . . . . . . . . 42
RS10 . . . . . . . . . . . . . 86
RS2 . . . . . . . . . . . . . . 42
RS20 . . . . . . . . . . . . . 86
RS3 . . . . . . . . . . . . . . 42
RSC1250 . . . . . . . . . . 46
RSC1280 . . . . . . . . . . 46
RSC28 . . . . . . . . . . . . 46
RSC44 . . . . . . . . . . . . 46
RSC72 . . . . . . . . . . . . 46
RSL3301. . . . . . . . . . . 20
RSL3302. . . . . . . . . . . 20
RT . . . . . . . . . . . . . . 154
RT1 . . . . . . . . . . . . . . 86
RT2 . . . . . . . . . . . . . . 86
RX1 . . . . . . . . . . . . . . 75
RX10 . . . . . . . . . . . . . 86
RX2 . . . . . . . . . . . . . . 75
RX20 . . . . . . . . . . . . . 86
RXL31. . . . . . . . . . . . . 17
RXL32. . . . . . . . . . . . . 17
RXL3301. . . . . . . . . . . 19
RXL3301F. . . . . . . . . . 21
RXL3302. . . . . . . . . . . 19
RXL3302F. . . . . . . . . . 21
SB . . . . . . . . . . . 90, 194
SIPR. . . . . . . . . . . . . 136
SM18 . . . . . . . . . . 40, 41
SM28 . . . . . . . . . . . . . 47
SM36 . . . . . . . 40, 41, 47
SM44 . . . . . . . . . . . . . 47
SM72 . . . . . . . 40, 41, 47
TUF-1. . . . . . . . . . . . . 63
TUF-2. . . . . . . . . . . . . 63
TUFHZ. . . . . . . . . . . . 69
ULT12120. . . . . . . . . 123
ULT12150. . . . . . . . . 123
ULT1280. . . . . . . . . . 123
ULT640. . . . . . . . . . . 123
ULT672. . . . . . . . . . . 123
ULTB . . . . . . . . . . . . . 53
ULTD . . . . . . . . . . . . . 25
ULTW. . . . . . . . . . . . . 53
VM. . . . . . . . . . . . . . 158
VQ . . . . . . . . . . . . . . 158
VT. . . . . . . . . . . . . . . 158
WH. . . . . . . . . . . . . . 162
WHR. . . . . . . . . . . . . 163
WQ. . . . . . . . . . . . . . 162
WS. . . . . . . . . . . . . . 162
WSR. . . . . . . . . . . . . 163
WT. . . . . . . . . . . . . . 162
ZCP . . . . . . . . . . . . . 203
TOLL FREE:
866-851-9680
FAX:
866-601-0002
THINKING GREEN!
www.ready-lite.ca
All information and specifications contained in this catalogue are subject to
change due to engineer design, errors and omissions.
Illustrations and diagrams within this catalogue may vary from actual products.
© 2014 Thomas & Betts Limited. All rights reserved.
Printed in Canada 2014/11/3000 Order No.: RLCAT-ENG
We have printed with soya based inks that
have a reduced VOC content of less that 5%.
(Certified by Terrachoice – Method 24)
Water based varnish has been used in order to
minimize COVs and to facilitate the recycling of
the printed product once its lifecycle has ended.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement