DeWalt | DW920 | Technical data | DeWalt DW920 Technical data

DeWalt DW920 Technical data
®
DW920
Dansk
1
Deutsch
7
English
14
Español
20
Français
26
Italiano
32
Nederlands
39
Norsk
45
Português
51
Suomi
57
Svenska
63
Türkçe
69
EÏÏËÓÈη
75
Copyright DEWALT
3
5
4
2
1
6
7
8
7
9
10
A
3
5
B
C
12
D
11
4
1
E
2
ENGLISH
CORDLESS TWO POSITION DRILL/DRIVER
DW920
Congratulations!
You have chosen a DEWALT Power Tool. Years of
experience, thorough product development and
innovation make DEWALT one of the most reliable
partners for professional Power Tool users.
The following symbols are used throughout this
manual:
Denotes risk of personal injury, loss of life
or damage to the tool in case of nonobservance of the instructions in this
manual.
Table of contents
Technical data
EC-Declaration of conformity
Safety instructions
Package contents
Description
Electrical safety
Mains plug replacement (U.K. & Ireland only)
Using an extension cable
Assembly and adjustment
Instructions for use
Maintenance
Guarantee
en - 1
en - 1
en - 2
en - 3
en - 3
en - 4
en - 4
en - 4
en - 4
en - 5
en - 5
en - 6
Technical data
Voltage
V
No-load speed
min-1
Max. torque
Nm
Tool holder
Weight (without battery pack)
kg
DW920
7.2
0-500
9
6.35 mm hex
0.8
Battery pack
Voltage
Capacity
Weight
DE9057
7.2
1.3
0.3
V
Ah
kg
Denotes risk of electric shock.
Fire hazard.
EC-Declaration of conformity
DW920
DEWALT declares that these Power Tools have been
designed in compliance with: 98/37/EEC,
89/336/EEC, 73/23/EEC, EN 50144, EN 50260,
EN 55014-2, EN 55014, EN 60335, EN 61000-3-2 &
EN 61000-3-3.
For more information, please contact DEWALT at the
address below, or refer to the back of the manual.
Level of sound pressure according to 86/188/EEC &
98/37/EEC, measured according to EN 50144:
DW920
LpA
(sound pressure)
LWA (acoustic power)
Charger
Mains voltage
Approx. charging time
Weight
Fuses:
Europe
U.K. & Ireland
230 V tools
230 V tools
VAC
h
kg
DE9118
230
1
0.4
10 Amperes, mains
3 Amperes, in plugs
dB(A)*
68.35
dB(A)
81.35
* at the operator’s ear
Take appropriate measures for the
protection of hearing if the sound
pressure of 85 dB(A) is exceeded.
Weighted root mean square acceleration value
according to EN 50144:
DW920
0.34 m/s2
en - 1
14
ENGLISH
Director Engineering and Product Development
Horst Großmann
DEWALT, Richard-Klinger-Straße 40,
D-65510, Idstein, Germany
Safety instructions
When using Power Tools, always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and
personal injury. Read the following safety
instructions before attempting to operate this
product. Keep these instructions in a safe place!
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose Power Tools to humidity. Keep
work area well lit. Do not use Power Tools in the
presence of flammable liquids or gases.
3 Guard against electric shock
Prevent body contact with earthed surfaces
(e.g. pipes, radiators, cookers and refrigerators).
For use under extreme conditions (e.g. high
humidity, when metal swarf is being produced,
etc.) electric safety can be improved by inserting
an isolating transformer or a (FI) earth-leakage
circuit-breaker.
4 Keep children away
Do not let children come into contact with the
tool or extension cord. Supervision is required for
those under 16 years of age.
5 Store idle tools
When not in use, Power Tools must be stored in
a dry place and locked up securely, out of reach
of children.
6 Dress properly
Do not wear loose clothing or jewellery.
They can be caught in moving parts. Preferably
wear rubber gloves and non-slip footwear when
working outdoors. Wear protective hair covering
to keep long hair out of the way.
15
7 Wear safety goggles
Also use a face or dust mask in case the
operations produce dust or flying particles.
8 Beware of maximum sound pressure
Take appropriate measures for the protection of
hearing if the sound pressure of 85 dB(A)
is exceeded.
9 Secure workpiece
Use clamps or a vice to hold the workpiece. It is
safer and it frees both hands to operate the tool.
10 Do not overreach
Keep proper footing and balance at all times.
11 Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
12 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches
are removed from the tool before operating the
tool.
13 Use appropriate tool
The intended use is described in this instruction
manual. Do not force small tools or attachments
to do the job of a heavy-duty tool. The tool will
do the job better and safer at the rate for which it
was intended.
Warning! The use of any accessory or attachment
or performance of any operation with this tool, other
than those recommended in this instruction manual
may present a risk of personal injury.
14 Maintain tools with care
Keep the tools in good condition and clean for
better and safer performance. Follow the
instructions for maintenance and changing
accessories. Inspect the tool cords at regular
intervals and, if damaged, have them repaired by
an authorized DEWALT repair agent. Keep all
controls dry, clean and free from oil and grease.
15 Check for damaged parts
Before using the tool, carefully check it for
damage to ensure that it will operate properly
and perform its intended function. Check for
misalignment and seizure of moving parts,
breakage of parts and any other conditions that
may affect its operation. Have damaged guards
or other defective parts repaired or replaced as
instructed.
Do not use the tool if the switch is defective.
Have the switch replaced by an authorized
DEWALT repair agent.
en - 2
ENGLISH
16 Remove the battery pack
Remove the battery pack when not in use, before
servicing and when changing accessories.
17 Have your tool repaired by an authorized
DEWALT repair agent
This Power Tool is in accordance with the
relevant safety regulations. To avoid danger,
electric appliances must only be repaired by
qualified technicians.
Additional safety instructions for battery packs
Use only with DEWALT battery packs,
others may burst, causing personal injury
and damage
Do not expose to water
Have defective cords replaced
immediately
+40 ˚c
+4 ˚c
Charge only between 4 °C and 40 °C
Fire hazard! Avoid metal short circuiting
the contacts of a detached battery pack
(e.g. keys carried in the same pocket as
a battery pack).
• The battery fluid, a 25-30% solution of potassium
hydroxide, can be harmful. In case of skin contact,
flush immediately with water. Neutralize with a mild
acid such as lemon juice or vinegar. In case of eye
contact, rinse abundantly with clean water for at
least 10 minutes. Consult a physician.
• Never attempt to open a battery pack for any
reason.
Labels on charger and battery pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
100%
Discard the battery pack with due care
for the environment
Do not incinerate the battery pack
Package contents
The package contains:
1 Cordless drill/driver
1 Battery charger
1 Battery pack (K models)
2 Battery packs (K2 models)
1 Screwdriver bit
1 Kitbox
1 Instruction manual
1 Exploded drawing
Battery charging
100%
Battery charged
Battery defective
Do not probe with conductive objects
Do not charge damaged battery packs
Read instruction manual before use
en - 3
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand
this manual prior to operation.
Description (fig. A)
Your cordless drill/driver DW920 has been designed
for professional drilling and screwdriving applications.
1 Variable speed switch
2 Forward/reverse slider
3 Head release button
4 Mode selector/torque adjustment collar
5 Tool holder sleeve
6 Screwdriver bit
7 Battery pack
16
ENGLISH
Charger
Your DE9118 charger accepts DEWALT NiCd
battery packs ranging from 7.2 V to 14.4 V.
7 Battery pack
8 Release buttons
9 Charger
10 Charging indicator (red)
Electrical safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
power corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DEWALT charger is double
insulated in accordance with EN 60335.
Mains plug replacement
(U.K. & Ireland only)
• Should your mains plug need replacing and you
are competent to do this, proceed as instructed
below. If you are in doubt, contact an authorized
DEWALT repair agent or a qualified electrician.
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs
fitted with the correctly rated fuse (1).
• The cable wire colours, or a letter, will be marked
at the connection points of most good quality
plugs. Attach the wires to their respective points
in the plug (see below). Brown is for Live (L) (2)
and Blue is for Neutral (N) (4).
• Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the
outer sheath of the cable firmly and that the two
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
Using an extension cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm2; the maximum length is 30 m.
Assembly and adjustment
Prior to assembly and adjustment,
always remove the battery pack.
• Always switch off the tool before
inserting or removing the battery pack.
• Use only DEWALT battery packs and
chargers.
Battery pack (fig. A)
Charging the battery pack
When charging the battery pack for the first time,
or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles,
the battery pack will attain full capacity. Always check
the mains prior to charging the battery pack. If the
mains is functioning but the battery pack does not
charge, take your charger to an authorised DEWALT
repair agent. Whilst charging, the charger and the
battery pack may become warm to touch. This is a
normal condition and does not indicate a problem.
Do not charge the battery pack at
ambient temperatures <4 °C or >40 °C.
Recommended charging temperature:
approx. 24 °C.
• To charge the battery pack (7), insert it into the
charger (9) as shown and plug in the charger.
Be sure that the battery pack is fully seated in the
charger. The red charging indicator (10) will blink.
After approx. 1 hour, it will stop blinking and
remain on. The battery pack is now fully charged
and the charger automatically switches to
equalise mode.
17
en - 4
ENGLISH
After approx. 4 hours, it will switch to maintenance
charge mode. The battery pack can be removed
at any time or left in the connected charger
indefinitely.
• The red charging indicator flashes rapidly to
indicate a charging problem. Reinsert the battery
pack or try a new one. If the new pack also
refuses to charge, have your charger tested by
an authorized DEWALT repair agent.
• When plugged into power sources such as
generators or sources that convert DC to AC,
the red charging indicator may blink twice, switch
off and repeat. This indicates a temporary
problem of the power source. The charger will
automatically switch back to normal operation.
Inserting and removing the battery pack
• Insert the battery pack into the grip until it clicks
in place.
• To remove the battery pack, press the two
release buttons (8) simultaneously and pull the
pack out of the grip.
Inserting and removing bits (fig. A & B)
• Pull the sleeve (5) backwards and insert the
screwdriver bit (11).
• Release the sleeve.
• To remove the bit, pull the sleeve backwards and
pull the bit out of the holder.
Swivelling the tool head (fig. C)
The head of the tool can be swivelled for optimum
versatility.
• Press the release button (3).
• Swivel the tool head into the desired position.
• Release the button.
Selecting the operating mode or adjusting the
torque (fig. D)
The collar of this tool has 15 positions for the
adjustment of the torque to suit the size of the screw
and the workpiece material. For torque adjustment,
refer to the section «Screwdriving».
• Select the drilling mode or torque by aligning the
symbol or number on the collar (4) with the
indicator (12) on the housing.
Forward/reverse slider (fig. E)
• To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows
on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Prior to operation:
• Make sure your battery pack is (fully) charged.
• Insert the appropriate bit.
• Select forward or reverse rotation.
Switching on and off (fig. E)
• To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed switch
determines the tool speed.
• To stop the tool, release the switch.
• To lock the tool in off position, move the forward/
reverse slider (2) to the central position.
Screwdriving (fig. A)
• Select forward or reverse rotation using the
slider (2).
• Set the collar (4) to position 1 and begin
screwdriving (low torque).
• If the clutch ratchets too soon, adjust the collar
to increase the torque as required.
Consult your dealer for further information on the
appropriate accessories.
Maintenance
Your DEWALT Power Tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
en - 5
18
ENGLISH
GUARANTEE
Cleaning
• Unplug the charger before cleaning the housing
with a soft cloth.
• Remove the battery pack before cleaning your
Power Tool.
• Keep the ventilation slots clear and regularly
clean the housing with a soft cloth.
Environment
Rechargeable battery pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely,
then remove it from the tool.
• NiCd and NiMH cells are recyclable. Take them
to your dealer or a local recycling station.
The collected battery packs will be recycled or
disposed of properly.
Unwanted tools
Take your tool to an authorised DEWALT repair
agent where it will be disposed of in an
environmentally safe way.
19
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your DEWALT tool, simply return
it within 30 days, complete as purchased, to the
point of purchase, for a full refund or exchange.
Proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
DEWALT tool, in the 12 months following
purchase, it will be undertaken free of charge at
an authorized DEWALT repair agent. Proof of
purchase must be produced. Includes labour and
spare parts for Power Tools. Excludes accessories.
• ONE YEAR FULL WARRANTY •
If your DEWALT product becomes defective due
to faulty materials or workmanship within
12 months from the date of purchase,
we guarantee to replace all defective parts free of
charge or, at our discretion, replace the unit free
of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by
unauthorized persons.
• Proof of purchase date is produced.
This guarantee is offered as an extra benefit
and is additional to consumers statutory rights.
For the location of your nearest authorized DEWALT
repair agent, please use the appropriate telephone
number on the back of this manual. Alternatively,
a list of authorized DEWALT repair agents and full
details on our after-sales service are available on
the Internet at www.2helpU.com.
en - 6
Belgique et Luxembourg
België en Luxemburg
DEWALT
Weihoek 1, Nossegem
1930 Zaventem-Zuid
Danmark
DEWALT
Hejrevang 26 B
3450 Allerød
Tlf: 70 20 15 10
Fax: 48 14 13 99
Deutschland
DEWALT
Richard-Klinger-Straße
65510 Idstein
Tel: 06 12 62 16
Fax: 061 26 21 24 40
EÏÏ¿˜
DEWALT
§ÂˆÊ ™˘ÁÁÚÔ‡ 154
176 71 K·ÏÏÈı¤·, ∞ı‹Ó·
España
DEWALT
Ctra de Acceso
a Roda de Barà, km 0,7, 43883 Roda de Barà, Tarragona
Tel: 977 29 71 00
Fax: 977 29 71 38
Fax: 977 29 71 19
France
DEWALT
Le Paisy
BP 21, 69571 Dardilly Cedex
Tel: 472 20 39 20
Tlx: 30 62 24F
Fax: 472 20 39 00
Helvetia
Schweiz
DEWALT/Rofo AG
Warpel
3186 Düdingen
Tel: 037 43 40 60
Fax: 037 43 40 61
Ireland
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel: 012 78 18 00
Fax: 012 78 18 11
Italia
DEWALT
Viale Elvezia 2
20052 Monza (Mi)
Tel: 03 92 38 72 04
Fax: 03 92 38 75 93
Nederland
DEWALT
Florijnstraat 10
4879 AH Etten-Leur
Tel: 07 65 08 22 01
Fax: 07 65 03 81 84
Norge
DEWALT
Strømsveien 344
1081 Oslo
Tel: 22 99 90 00
Fax: 22 99 90 01
Österreich
DEWALT
Werkzeugevertriebs GmbH
Erlaaerstraße 165, Postfach 320,1231 Wien
Tel: 022 26 61 16
Tlx: 13228 Black A
Fax: 022 26 61 16 14
Portugal
DEWALT
Rua Egas Moniz 173
Apartado 19, S. João do Estoril, 2768 Estoril, Codex
Tel: 468 7513/7613
Tlx: 16607 Bladec P
Fax: 466 38 41
Suomi
DEWALT
Palotie 3
01610 Vantaa
Puh: 98 25 45 40
Fax: 98 25 45 444
Brandvägen 3
01610 Vanda
Tel: 98 25 45 40
Fax: 98 25 45 444
Sverige
DEWALT
Box 603
421 26 Västra Frölunda, Besöksadr. Ekonomivägen 11
Tel: 031 68 61 00
Fax: 031 68 60 08
Türkiye
DEWALT
Merkez Mahallesi, Köyaltı Mevkii, Şahnur Sokak
(OTTO Binası) 34530 Yenibosna/İstanbul (PBX)
United Kingdom
DEWALT
210 Bath Road
Slough, Berks SL1 3YD
07 - 00
Tel: 02 719 07 12
Fax: 02 721 40 45
Service fax: 02 719 08 10
TËÏ: 019 24 28 70
Fax: 019 24 28 69
Service: 019 24 28 76-7
Tel: 021 26 39 06 26
Faks: 021 26 39 06 35
Tel: 017 53 57 42 77
Fax: 017 53 52 13 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising