BTC | BCO5216IA | User`s manual | BTC BCO5216IA User`s manual

BTC BCO5216IA User`s manual
Dual Digital Drive
COMBO 5216IA
User’s Manual
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASER KLASSE 1
LUOKAN 1 LASERLAITE
PRODUIT LASER
CATEGORIE 1
DANGER
VORSICHT
ATTENTION
INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT
EXPOSURE TO BEAM
INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET
NICHT DEM STRAHL AUSSETSEN
RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
EVITER TOUTE EXPOSITION AUX RAYONS.
Copyright Statement
It is a criminal offence, under applicable copyright laws, to make unauthorised
copies of copyright-protected material, including computer programs, films,
broadcasts and sound recordings. This equipment should not be used for such
purposes.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may
cause undesired operation.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FOR EUROPE
“The drive is in conformity with the EMC directive and low-voltage directive.”
Table of Contents
INTRODUCTION
SYSTEM REQUIREMENTS
PACKAGE CONTENTS
INSTALLATION
1
2
2
3
HOST INTERFACE CONNECTIONS
HARDWARE INSTALLATION
DRIVER INSTALLATION
SOFTWARE INSTALLATION
DVD REGION CODE
3
4
6
9
11
OPERATION & CONNECTION
13
FRONT PANEL
REAR VIEW
TECHNICAL DATA
13
15
17
Dual Digital Drive
INTRODUCTION
Welcome to a multimedia world of CD-ReWritable technology, DVD-ROM
capabilities and, memory card compatibility!
This compact and high-performance COMBO 5216IA frees up precious bay
space and presents you as an IDE Combo (CD-RW+DVD ROM) Drive and
a USB-connected card reader. It reads CDs of all types at maximum 52X
speed, and DVD-ROMs at maximum 16X speed. For the writing ability, it
writes to CD-Rs at up to 52X speed, and to CD-RWs at up to 24X speed.
Other than that, the built-in 7 in 1 card reader which offers read-write ability
of 7 memory card types simplifies the process of exchanging data between
Digital cameras, voice recorders, PDAs, MP3s… and your computer.
With this multi-functional solution and the bundled software package, you
can view, archive, or write files/photos/video/music directly from the drive
and enjoy the fascinating digital as well as the DVD entertainment on your
desktop.
Here are some important features of this Combo Drive:
♦
Easy installation with Combo drive of IDE and card reader of USB
1.1 interface (on board connection)
♦
8X, 16X, 24X, 32X, 40X, 48X and 52X writing speed on CD-R
media
♦
4X, 10X, 12X, 16X and 24X writing speed on CD-RW media
♦
Adopts “MTKSuperLink” to prevent Buffer Underrun
♦
Supports writing modes of TAO, DAO, SAO and packet writing
♦
Supports MultiRead function
♦
Four-slot integration works with CompactFlash, MicroDrive,
Memory Stick, Memory Stick Pro, MultiMediaCard, Secure Digital,
and SmartMedia
1
♦
Dual Digital Drive
♦
Smooth DVD playback
System Requirements
For IBM compatible PCs, the system requirements recommended are as
follows:
♦
Pentium II, Celeron 400MHz or above with at least 64MB of
memory
♦
Fast and sufficient hard disk space (minimum 200MB for
installation, 1GB or more is recommended.)
♦
IDE host interface supporting ATAPI MMC command & USB host
interface (if you don’t have USB on-board connection)
♦
Microsoft Windows 98SE/2000/ME/XP
Package Contents
The package contains the following items:
2
♦
Dual Digital Drive, COMBO 5216IA
♦
Audio cable
♦
2 Application software discs
♦
4pcs of screws/bag
♦
Quick Installation Guide
Dual Digital Drive
INSTALLATION
Host Interface Connections
Most current mainboard models have two IDE ports (primary and
secondary), which can connect two IDE cables. Two IDE cables allow you
to connect up to four devices, but it is recommended that you separate IDE
ports for your hard drive and your Dual Digital Combo Drive. This will
ensure that your hard drive’s performance and speed won’t be affected by
having the drive on the same cable.
Jumper Setting
On the rear panel of this drive, you will find three pairs of jumpers: CS
(CSEL), SL (Slave) and MA (Master). Use the jumper cap to set the device
to CS, SL or MA mode corresponding to your PC configuration. If you
connect only one device on the IDE cable, you can set the jumper as
“MASTER” or “SLAVE”.
If you connect two devices on the same cable, set different jumper for each
device (one as “MASTER”, and the other one as “SLAVE”). The same rule
applies to the connection of having your hard disk and another device on
the same cable.
3
Dual Digital Drive
CSEL
MASTER
SLAVE
JUMPER
Improper or conflicting setting will cause the unit not detected by your
system.
Hardware Installation
1. Turn off the power to your computer system.
2. Disconnect the power cord and all cables from the back of your
computer, and then remove the cover of the computer.
3. Insert the drive into one of the vacant 5.25" drive bays and
secure it to your PC with all four mounting screws.
4. Connect one end of the 40-pin IDE cable to the IDE connector of
this drive and the other end to the IDE port on your mainboard.
Also, connect the power supply cable to the back of the drive.
Power In
Make sure to align and connect the red-edge of the IDE Cable to
Pin 1 on the drive.
4
Dual Digital Drive
5. If you have a sound card that can be connected to the drive, you
can also connect the drive (as Audio-Out) and the sound card (as
Audio-in) with a 4-pin audio cable.
If your mainboad is integrated with built-in sound system, plug the
4-pin audio cable into the CD-IN connector on the mainboard as
Audio-in.
6.
Connect the USB cable at the back of the drive to the USB
header on the computer’s mainboard. The red wire of the cable
needs to be plugged into Pin 1 on the board. If the connection is
correct, the lower LED on the front panel will light Yellow.
This drive supports USB 1.1 and if you connect to USB 2.0
connector, only transfer rate of USB 1.1 will be available.
USB
RED WIRE
IDE
RED WIRE
Mainboard
Signal
Red/Vcc
White/DGreen/D+
Black/Ground
Braided Shield Ground
Pin #
1
2
3
4
5
USB Header
7. Re-attach the cover of the computer, and reconnect the power
cord and all cables to the computer.
5
Dual Digital Drive
Driver Installation
For the Combo Drive
For the Combo Drive itself, it’s an IDE device supporting Plug & Play and
Windows 98SE/ME/2000/XP can automatically detect the drive and load
the appropriate driver.
For the Card Reader
Windows 98SE/2000
If you are using Window 98SE or 2000, please install the provided driver.
6
1.
Insert the application disc.
2.
Select:\Card Reader Driver
3.
Click “setup.exe”, and follow the on-screen instructions:
Dual Digital Drive
Click “OK” if you have already had USB cable connected (Refer
to Hardware Installation, Step 6.)
7
Dual Digital Drive
Make sure to restart your computer.
Windows ME/XP
Since Windows ME and XP already have USB Mass Storage support,
the card reader can be detected and work fine without installing driver.
However, we recommend that you install the provided driver to have
more explicit operation status of the card reader, as described below.
For Windows XP users, please upgrade to Service Pack 1.
8
Dual Digital Drive
After the driver installation, 4 extra icons with different card type indicated
will show in Device Manager/My computer. And then you can use each slot
of the card reader for file archiving/recording.
While the card reader is reading data of memory cards, the icon for the
card accessed will light up and the LED beside the card slot on the front
panel will flash Green.
Software Installation
Burning Software
The bundled recording software gives you the complete solution for making
audio/data CDs. With the user-friendly interface, it guides you through the
creation and backup of files/photos/video/music from your computer to a
recordable compact disc. Combining of the card reader capabilities, no
matter you are a novice or an experienced user; you can enrich your digital
life with this best recording tool.
DVD Playback Software
The DVD playback software has a newly enhanced MPEG-1 and 2
decoder to provide you with the most rich and powerful image quality. It is
based on the proprietary MPEG-2 video decoding engine that supports full
9
Dual Digital Drive
resolution 720 x 480 video playback. You can enjoy the wide range of
educational and entertaining CD/DVD titles with sound and visual effect of
theater quality.
Windows Environment
1.
Insert the application CD and the installation program will run
automatically. Then follow the on-screen procedures.
Or
2.
10
Run:\setup.exe on the application CD.
Dual Digital Drive
DVD Region Code
Region Playback Control Management
All DVD Video Playback systems have “Region Playback Control”
management (RPC) which is required by Hollywood movie industry and
defined by DVD Forum. This includes DVD-Video players and PC systems
with DVD-Video capability. You can only play DVD-Video discs with the
same region code as your DVD-Video Playback system.
As for DVD-ROM drives, one kind of the DVD-Video Playback system,
there are 2 types:
RPC Phase 1 (as RPC1): RPC1 drives do not have built-in hardware
support for region management. DVD-ROM drives of this kind don’t play a
part in controlling the playback region. It solely depends on the decoder.
RPC Phase 2 (as RPC2): RPC2 drives maintain the region change count
information in hardware, and in general, the region of such drives can be
changed up to 5 times by the end users under some software decoder (e.g.
PowerDVD).
And referring to the region codes, there are 6 regions worldwide, and
normally, there is a region code mark on the package of DVD titles. :
Region 1: Canada, US
Region 2: Japan, Europe, South Africa, and Middle East (including
Egypt)
Region 3: Southeast Asia and East Asia (including Hong Kong)
Region 4: Australia, New Zealand, Pacific Islands, Central America,
Mexico, South America, and the Caribbean
Region 5: Eastern Europe, Indian subcontinent, Africa, North Korea,
and Mongolia
Region 6: China
11
Dual Digital Drive
About This Dual Digital Combo Drive
This drive is also a RPC2 DVD-ROM drive and according to DVD-Forum,
PC chip must be designed into DVD-ROM drives to record how many times
a user has changed the region code. The first region code will depend on
the DVD title you play and you are allowed to modify the region code 5
times (including the initial one). After the fifth alteration, the region code will
be locked and only those DVD titles of the same region code could be
played afterwards, so set the code carefully.
12
Dual Digital Drive
OPERATION & CONNECTION
Front Panel
2
5
1
11
7
8
3
4
6
9
10
1. Headphone Jack
By plugging in the stereo mini jack here, you can listen to an audio
disc directly playing from the drive with headphones.
2. Headphone Volume Control
This rotary knob adjusts the audio output level. Turn the wheel to the
right/left for the volume control of your headphone.
3. Play/Skip button
Press this button to play tracks or skip to next track during the
playing state.
The default reading speed is 40X. Pressing Play button for 3
seconds will change the speed to 52X. While at 52X mode, pressing
Eject button for 3 seconds or ejecting the tray will reset the drive
speed from 52X to 40X.
13
Dual Digital Drive
4. Close/Eject button
This button opens and closes the disc tray. If the tray is closed,
pressing the button will eject it. If the drive is playing audio, pressing
this button will stop it.
5. Led Indicator (Combo Drive)
Flashes “green” while verifying or reading a CD/DVD.
Flashes “red” while writing data.
While the tray goes in/out, the indicator lights green and it’s off when
the drive is ready.
6. LED Indicator (card reader)
Once the USB cable is correctly connected, this LED will light yellow,
which means the card slots are ready to use.
7. Slot for Memory Stick (MS)/Memory Stick Pro (MS Pro)
8. Slot for Secure Digital (SD)/MultiMediaCard (MMC)
9. Slot for Compact Flash(CF) Type I, II/MicroDrive
10. Slot for Smart Media
11. Emergency Eject Hole
When the Close/Eject button doesn’t work properly and the disc tray
can’t be opened, you can insert a paper clip or a small rod into this
hole for manual ejection. Please make sure to power off the system
before you do that.
Note: The design of front panel is subject to change without notice.
14
Dual Digital Drive
Rear View
3
4
5
6
1. Digital Audio Output Connector
If your sound card has a digital audio IEC958 format connector, you
can connect it to this digital audio output connector with a 2-pin
audio cable.
2. Analog Audio Output Connector
This connector allows you to connect the drive to your sound card
with a 4-pin audio cable.
3. Device Configuration Jumper
Set the jumper to Master, Slave or Cable Select according to your
system configuration.
4. IDE Interface Connector
Plug one end of the 40-pin IDE cable here to join the 40-pin IDE
connector on the mainboard. The red-edge of the IDE cable must be
connected to Pin 1 of each connector.
15
Dual Digital Drive
5. Power Supply Connector
By plugging the computer’s power supply cable here, you can
connect the drive and your computer system.
6. USB Cable
Connect the USB cable to the USB connector on the mainboard.
The red wire of the cable needs to plug into Pin 1 on the board.
16
Dual Digital Drive
TECHNICAL DATA
Interface
Combo Drive: IDE
Card Reader: USB 1.1
Form factor
5.25" Half Height
Writing speed
CD-R: 8X/16X/24X/32X/40X/48X/52X
CD-RW: 4X/10X/12X/16X/24X
Writing modes
TAO (Track at once), DAO (Disc
At Once), SAO (Session at once),
Multi-session, Incremental Packet
Writing
Digital Media
CompactFlash, MicroDrive, Memory
Stick, Memory Stick Pro, SmartMedia,
MultiMediaCard, and Secure Digital
Transfer rate
Combo Drive
Read:
CD-ROM: 7800kb/sec (up to 52X)
CD-RW: 4800kb/sec (up to 32X)
DVD: 21632kb/sec (up to 16X)
Write:
CD-R: 7800kb/sec (up to 52X)
CD-RW: 3600kb/sec (up to 24X)
Card Reader
Read: Up to 1.5MB/s
Write: Up to 1.5MB/s
Access time (⅓ stroke)
CD/DVD: 110/130 ms
17
Dual Digital Drive
Disc Format Supported
Write
Read
CD-DA
CD-ROM
CD-ROM XA
CD-EXTRA
Video CD
Photo CD
CD-I
CD-TEXT
DVD-ROM (DVD-5, DVD-9,
DVD-10, DVD-18)
DVD+RW, DVD-RW
Data buffer
2MB
Disc loading
Tray (motorised), Dust Sealed
Audio output level
Line out = 0.6 ± 10%Vrms
Headphone out = 0.6± 10%Vrms
Power
5 VDC & 12VDC
Card Reader power directly from
computer power supply through USB
connection
Dimensions
Height
Width
Depth
Weight
18
41.8 ± 0.2 mm
148.8 ± 0.2 mm
193.4 ± 0.3mm
1 kg
Dual Digital Drive
Environment
Combo Drive
Temperature
Operating
5°C to 45°C
Non-operating
-20°C to 60°C
Humidity
Operating
8% ~ 80%RH
Non-operating
5% ~ 95%RH
Card Reader
Temperature
Operating
0°C to 40°C
Non-operating
-20°C to 45°C
Humidity
Operating
0% ~ 90%RH
Non-operating
0% ~ 95%RH
Disc
Disc Size
80mm and 120mm discs
Disc Data Capacity
DVD-ROM: Single layer – 4.7GB
Dual layer – 8.5GB (one side)
CD-ROM: 74min – 650MB – Mode 1
80min – 700MB – Mode 1
19
3100551980
Version 1.0
Oct. 2003
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising