D GB F NL I E TR 608 top L TERMINA Channel statuses REG 1 TE ON = 1-channel 7 day timer OFF = Menu Man ok Res - 1 2 The decision Yes confirms the selection or programming + 3 Decision No means continue ... Load Selection e.g.: Prog, n Man Abort input n Current days of the week 1 = Monday, 2 = Tuesday, ... 1 2 3 4 5 6 7 Power reserve mode Three flashing dots The connection and installation of electrical appliances must be performed by a skilled electrician only. Any intervention into or modifications to the appliance shall lead to the lapse of all warranty rights. Comply with your national regulations and all relevant safety stipulations. N M Prog Service voltage OK Two flashing dots Safety Information 310 967 02 P N L1 L2 1. info • A replaceable lithium cell (CR 2032) is included in the package. • The stored data are retained and are available after the return of mains power or by pressing a button (display active). • The lithium cell may be replaced only when the device is isolated from the power supply system. • The timer has not been preset with a date and time. • Battery status display: If the LCD display is blinking, the device only has a power reserve of approx. 3 weeks in the case of a power failure. First First contact 2. action Selection of the national language Initial operation Menu - For programming, viewing or deleting First of all read the text display. Menu selection Select by pressing the Prog key. Confirm by pressing . By pressing the key select the desired menu. e.g. New, View or Delete. Confirm your selection by pressing . Set or change: by pressing or . Store by pressing . To display the switching times: In the menu View, press the key several times. Ok Res + 3. OK The decision Yes, confirms the For initial operation, the battery must be installed. In order to boost infothe power reserve, the display will shut off after 15 minutes in battery mode. Activate the clock, select the national language By pressing the or key select your national language. Store your selection by pressing the key. Repeat the above steps for setting the month, day, hour and minute. Press the key to call the programming and prompting programs. The displayed texts prompt you to make a decision. info selection or programming. + The decision No, means continue. Set or amend by pressing the or keys. According to According version to version According to According version to version OK RESET (only in case of emergency): If you perform a RESET of the timer, the individual settings will be deleted. The programmes switching times remain intact. Press the RES key with and a pointed object for approx. 1 second. Menue - Ok Res + Menu Menu Prog Menu Prog Man Man Prog Man OK OK OK + OK + OK OK + OK OK OK Technical Data TR 608 0 xxx 230V~ +/- 10% 50-60 Hz 240V~ +6%-14% 50-60 Hz 16 (4) A 250 V ~ min. 100 mA 24 V AC/DC Type 1 BSTU IEC/EN 60730-2-7 Degree of protection II EN 60355-1 IP 20 EN 60529 28 memory locations 1000W 7x7 6 x 11 5 x 15 5 x 20 5 x 23 W W W W W 200 VA (18µF) AgSnO 2 1000W 800VA Progr amming the switching time Programming info Formation of day groups If the same switching times are active on several days of the week, they occupy just one memory location, e.g. Monday – Friday 7.30 hrs ON. 28 memory locations are available. Group formation In answer to the text question Copy, decide by pressing the key that the day program should be copied to another day of the week. Switching times for lighting systems, machines, ventilation systems, alarm systems etc. Menue Example: Switching on the lighting of a sports hall on Mon., Tues., Thurs., Fri. from 7.30h until 12h. Programming example Select Prog by pressing the key. Store your selection by pressing the key. Select New by pressing the or . Store your selection by pressing the key. Select ON by pressing or . Store your selection by pressing . Set the hours and minutes by pressing the or key. Store selection by pressing . Prog OK OK + OK + OK info When programming an ON and OFF switching time, e.g. Monday 9 AM, a switch-off at 9 AM always has priority. Program review Following programming the timer makes a program review back to midnight and then sets the correct switching status. OK OK OK OK 1 2 3 action Example + OK + + 4 6 7 5 OK To store this day of the week only Select weekday by pressing or . Select store by pressing . Store by pressing To copy to other days of the week Store COPY by pressing . Select weekday by pressing or . Store by pressing To leave out a day of the week, skip by pressing the key. Finally select the STORE display by pressing . Store your selection by pressing . Override P ermanent ON or OFF Via the automatic menu Auto only Individual deletions Menu - Res ok + Press the two keys for approx. 1 s. (switches alternately or ). Symbol appears. Manual preselection is corrected again by the stored program. MENU Cancellation of manual preselection/ permanent switching: Briefly press the keys shown above. Prog Man OK Permanent ON or OFF Press both keys for approx. 2 s. Symbol appears. Press both keys for approx. 2 s. Symbol appears. + OK OK Cancellation of manual preselection/ permanent switching: Briefly press the keys shown above. OK OK OK OK Setting/ correcting correcting the date and time summer/winter time Automatic summer/winter time correction According to version the timer is preprogrammed ex-works complete with the changeover. Should you switch off the automatic facility or wish to alter it, first of all read the text display. Select by pressing or . Store by pressing . Summer / Winter time setting has already been programmed: The timer has already been programmed with the summer and winter time ex works. Summer / Winter time rule is freely programmable: To this end you have to enter a month and week, e.g.: Month 3 = march Week 4 = 4th week of the month Week 5 = last week of the month Read the text display first of all. Select by pressing the or key. Store by pressing the key key. PIN code PIN The device can be locked against unauthorized use with a 4 digit code number. Select the Manual menu using Confirm with the button. oder Man . - Selection WITH PIN Select WITH PIN using oder . Confirm with the button. Make note of any desired 4-digits number. Select the first digit of your 4 digit code using . Confirm the entered digit with . Select further digits as described using oder . Confirm each selected digit with the button. The device is locked 90 sec. after the last keystroke and can only be operated after the correct PIN code is entered. Selection WITHOUT PIN Select WITHOUT PIN using Confirm with the button. oder . If a PIN code has been activated, the timer can no longer be activated without a valid PIN code after a RESET. The device must be sent in! TIMEGUARD LTD., Victory Park, 400 Edgware Road, London NW2 6ND Tel. 0208/4508944, Fax 0208/4525143 PETER WARBURTON PTY. LIMITED, 64 Brittania Road, Castle Hill NSW 2154, Australia, Tel.: (02) 9899 2908, Fax: (02) 9899 4486
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021