Instruction Manual Atomic Dual Alarm Clock model 13024 CONTENTS Unpacking Instructions............ 2 Package Contents................... 2 Product Registration................ 2 Features & Benefits.................. 3 Clock Setup............................ 5 Atomic Clock.......................... 6 Set the Time & Date................ 6 Placement Guidelines.............. 7 Using the Clock...................... 8 USB Charging......................... 8 Troubleshooting...................... 9 Care & Maintenance..............10 Specifications.........................10 FCC Information....................10 Customer Support.................. 11 Warranty.............................. 11 Questions? Contact Customer Support at (877) 221-1252 or visit www.AcuRite.com. SAVE THIS MANUAL FOR FUTURE REFERENCE. Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference. Unpacking Instructions Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove. Package Contents 1. Alarm clock 2. Power adapter 3. Instruction Manual IMPORTANT PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE PRODUCT REGISTRATION Register online to receive 1 year warranty protection www.AcuRite.com ►Register a Product 2 Features & Benefits FRONT OF CLOCK 1 1. Snooze Button/Night Light 2. Alarm #1 ON/OFF Switch + 3. Alarm #1 Setup Button - 4. UP, DOWN & SET Buttons INDOOR DIMMER for setup preferences. 6. Alarm #2 Setup Button 7. Alarm #2 ON/OFF Switch CHARGE USB DEVICE 3 2 4 5 6 8 DC 4.5 v 7 9 BACK OF CLOCK ALARM 8. + Brightness Button Increases display brightness. + + - - DIMMER VOLUME 9. +/— Alarm Volume Adjusts alarm volume. 10. — Brightness Button Decreases display brightness. 11. USB Charging CHARGE USB DEVICE 10 11 12 13 14 for compatible smartphones. 12. DC 5v Power Input DC 4.5 v 15 BOTTOM OF CLOCK (inside battery compartment) 13. RCC ON/OFF Switch Controls synchronization with the atomic signal. 14. ºF/ºC Temperature Units 15. Zone Button Press to select time zone. 3 Features & Benefits 1 2 3 9 INDOOR 4 5 7 6 8 1.Date 6. Alarm #2 Time 2. Atomic Clock 7. Alarm #2 Days Active Indicates weekday, weekend or every Sets itself to the correct time and automatically updates for Daylight Saving Time. day alarm. 8. Alarm Volume 3. Atomic Signal Strength 9. Indoor Temperature 4. Alarm #1 Time 5. Alarm #1 Days Active Indicates weekday, weekend or every day alarm. 4 Clock Setup 2 Install or Replace Backup 1 Plug in Power Adapter Batteries For the best performance, plug in the power adapter as the main power source for this product. 1. R emove the battery compartment cover. 2. Insert 3 x AA alkaline batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment. 1 3. Replace the battery cover. Plug in Power Adapter (on back of unit) 2 Install or Replace Backup Batteries 3 AA alkaline batteries IMPORTANT: Batteries are a backup power source to preserve records in the event of a power outage. Power adapter recommended as the primary power source to enjoy the full functionality of the product. PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS. BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals. 5 Atomic Clock (RCC) AcuRite atomic clocks use a radio-controlled signal (RCC) to synchronize to the correct time broadcast by the National Institute of Standards and Technology (NIST) Radio Station WWVB, located near Fort Collins, Colorado. WWVB broadcasts the current time and date with split-second accuracy. The atomic clock and calendar will maintain the correct time and date, and automatically update for daylight saving time to provide the most accurate timekeeping standard possible. When the RCC button, located under the battery compartment cover, is set to ON, the clock will automatically search for the atomic clock signal. To manually search for the atomic signal, make sure the RCC button is set to ON, then press AND HOLD the “ “ button. Please note: Signal reception is normally better at night and when the weather is clear. The atomic signal generally takes a few hours to synchronize, so it is important to manually set the time and date after powering on the clock. Set the Time & Date Press and hold the “ ” button, located on the front of the clock, to enter SET MODE. Once in SET MODE the preference you are currently setting will blink on the clock. To adjust the currently selected (flashing) item, press and release the “ “ “ buttons (press and HOLD to fast adjust). To save your adjustments, press and release the “ preference. The preference set order is as follows: ” or ” button to adjust the next TIME ZONE (PST MST CST EST AST HAST AKST) AUTO DST ON/OFF* CLOCK HOUR CLOCK MINUTE CALENDAR MONTH CALENDAR DATE CALENDAR YEAR You will automatically exit SET MODE if no buttons are pressed for 5 seconds. Enter SET MODE at any time by pressing the “ ” button. *If you live in an area that observes daylight saving time, DST should be set to ON, even if it is not currently Daylight Saving Time. 6 Alarm Clock Placement Place alarm clock in a dry area free of dirt and dust. To help ensure an accurate indoor temperature measurement, be sure to place the clock away from heat sources or vents. ALARM + INDOOR + - - DIMMER VOLUME CHARGE USB DEVICE DC 4.5 v Important Placement Guidelines •To ensure accurate temperature measurement, place out of direct sunlight and away from any heat sources or vents. •To maximize atomic signal reception, place unit away from large metallic items, thick walls, metal surfaces, or other objects that may limit radio communication. •To prevent wireless interference, place unit at least 3 ft (.9 m) away from electronic devices (TV, computer, microwave, radio, etc.). 7 OPERATION Using the Clock Set the Alarm Time Slide Alarm #1 and/or Alarm #2 switch ON (alarm time cannot be adjusted if the alarm is OFF). Press and release the “ MODE. 1” or the “ 2 ” button to enter ALARM SET To adjust the currently selected (flashing) item, press and release the “ “ “ buttons (press and HOLD to fast adjust). ” or 1 ” or “ To save your adjustments, press and release the “ 2 “ button to adjust the next preference. The preference set order is as follows: ALARM CLOCK HOUR ALARM CLOCK MINUTE ALARM EVERY DAY or WEEKDAY ONLY or WEEKEND ONLY You will automatically exit ALARM SET MODE if no buttons are pressed for 5 seconds. Enter ALARM SET MODE at any time by pressing the “ 1 ” or “ 2“ button. Backlight During power adapter use, press the Snooze button for momentary backlight at 100% brightness. During battery-powered use, press any button for momentary backlight. The backlight MAY turn off at 2:00AM and 3:00 AM to acquire the atomic clock (RCC) signal. USB Charging Charge your mobile device by plugging your device’s USB power cord (not included) into the USB charging port on the back of the clock. USB charging is only available during power adapter use; USB charging is not active when operating on battery power only. Note: Follow the manufacturer’s instructions for your mobile device(s) to determine compatibility with the USB charging feature on this product. Some devices may not support USB charging or may require a higher power rating than this product provides. Observe the charging status on your device. Ensure your device is working properly before attempting to charge. 8 ALARM + + - - DIMMER VOLUME CHARGE USB DEVICE DC 4.5 v Troubleshooting • The backlight may automatically turn off for 10 minutes at 2:00am and 3:00am to acquire the atomic clock signal. •V erify power adapter is plugged in. •C heck that the batteries are installed correctly. Batteries may need to be replaced. Clock is too dark, hard • Increase brightness using +/– buttons, located on the to read or doesn’t back of the clock. work • T he optimum viewing angle for this product is from slightly above it. •R eset the unit by unplugging the power supply from the wall outlet and remove any batteries that are installed. This will reset the alarm to the original factory settings. Time and date will need to be entered after a reset. Inaccurate temperature Atomic signal or time syncing problems •M ake sure the clock is placed out of direct sunlight and away from any heat sources or vents (see page 7). For additional troubleshooting, please visit: http://www.nist.gov/pml/div688/grp40/radioclocks.cfm If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call (877) 221-1252 for assistance. 9 Care & Maintenance Clock Care Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away from dust, dirt and moisture. Clean ventilation ports regularly with a gentle puff of air. Specifications TEMPERATURE RANGE 32ºF to 99ºF, 0ºC to 37ºC POWER 5v power adapter 3 x AA alkaline batteries (for backup only) FCC Information This device complies with part 15 of FCC rules. Operation is subject to the following two conditions: 1- This device may NOT cause harmful interference, and 2- This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device. 10 Customer Support AcuRite customer support is committed to providing you with best-inclass service. For assistance, please have the model number of this product available and contact us in any of the following ways: (877) 221-1252 email@example.com 24/7 support at www.AcuRite.com ► Installation Videos ► Register your Product ► Instruction Manuals ► Support User Forum ► Replacement Parts ► Submit IMPORTANT Feedback & Ideas PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE PRODUCT REGISTRATION Register online to receive 1 year warranty protection www.AcuRite.com Limited One Year Warranty ►Register a Product At AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase. warranty will not be breached, and Chaney will give no credit for products it manufactures which have received normal wear and tear, been damaged (including by acts of nature), tampered, abused, improperly installed, damaged in shipping, or repaired or altered by others than authorized representatives of Chaney. The above-described warranty is expressly in lieu of all other warranties, express or implied, and all other warranties are hereby expressly disclaimed, including without limitation the implied warranty of merchantability and the implied warranty of fitness for a particular purpose. Chaney expressly disclaims We recommend that you visit us at liability for special, consequential or incidental damages, www.AcuRite.com for the fastest way to register all whether arising in tort or by contract from any breach of this your product. However, product registration warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation does not eliminate the need to retain your or exclusion may not apply to you. Chaney further disclaims all original proof of purchase in order to obtain liability from personal injury relating to its products to the extent warranty benefits. permitted by law. By acceptance of any of Chaney’s products, Chaney Instrument Co. warrants that all products it manufactures the purchaser assumes all liability for the consequences arising from their use or misuse. No person, firm or corporation is to be of good material and workmanship, and to be free of authorized to assume for Chaney any other liability in connection defects when properly installed and operated for a period of with the sale of its products. Furthermore, no person, firm or one year from the date of purchase. Remedy for breach of this corporation is authorized to modify or waive the terms of this warranty is limited to repair or replacement of the defective paragraph, and the preceding paragraph, unless done in writing item(s). Any product which, under normal use and service, is and signed by a duly authorized agent of Chaney. This warranty proven to breach the warranty contained herein within ONE gives you specific legal rights, and you may also have other YEAR from date of sale will, upon examination by Chaney, rights which vary from state to state. and at its sole option, be repaired or replaced by Chaney. Transportation costs and charges for returned goods shall For in-warranty claims:Chaney Instrument Co. be paid for by the purchaser. Chaney hereby disclaims all 965 Wells St., Lake Geneva, WI 53147 responsibility for such transportation costs and charges. This 11 Weather Stations Temperature & Humidity Weather Alert Radio Kitchen Thermometers & Timers Clocks It’s more than accurate, it’s AcuRite offers an extensive assortment of precision instruments, designed to provide you with information you can depend on to Plan your day with confidence™. www.AcuRite.com Printed in China 13024 INST 091713 ©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project