Draper | SDS+ | Owner`s manual | Draper SDS+ Owner`s manual

Draper SDS+ Owner`s manual
SDS+ ROTARY
HAMMER DRILLS
■ STOCK No.57828 110V
57829 240V
57830 110V
57831 240V
■ PART No.PHD520VC
PHD520VC
PHD624VC
PHD624VC
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE
SAFE AND EFFECTIVE USE OF THIS TOOL.
09/99
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which
should be kept with the machine.
This manual describes the purpose for which this tool has been designed and contains all the necessary
information to ensure its correct and safe use.We recommend that this manual is read before any operation of
the machine, before performing any kind of adjustment to the machine, and prior to any maintenance tasks. By
following all the general safety instructions contained in this manual, it will ensure both machine and operator
safety, together with longer life of the tool itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
machine.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the Draper Tool
policy of continuous improvement determines the right to make modifications without prior warning.
SDS+ ROTARY
HAMMER DRILLS
■ STOCK No.57828 110V
57829 240V
57830 110V
57831 240V
CONTENTS:
■ PART No.PHD520VC
PHD520VC
PHD624VC
PHD624VC
Page No.
Declaration of Conformity ................................................................................1
Specification/Guarantee...................................................................................2
Power Supply ...................................................................................................3
General Safety Instructions ..............................................................................4
Know Your Hammer Drill ..................................................................................5
Operation & Use .....................................................................................6 and 7
Maintenance/parts/replacement......................................................................8
Optional Accessories .......................................................................................9
DECLARATION OF CONFORMITY
We
Draper Tools Ltd. Hursley Road, Chandler’s Ford, Eastleigh, Hampshire.
SO53 1YF. England.
Declare under our sole responsibility that the product:
Stock Nos:- 57828, 57829, 57830 & 57831.
Part Nos:- PHD520VC, PHD624VC.
Description:- SDS PN. Hammer.
To which this declaration relates is in conformity with the following directive(s)
98/37/EC & 89/336EEC.
With reference to:
EN50144, EN55014-1, EN55014-2 & EN60555.
JOHN DRAPER
Managing Director
09.99
SPECIFICATION
Part No. ........................................................PHD520VC ................................PHD624VC
Stock No .......................................................... 57828 ............................................57830
..........................................................................57829 ............................................57831
Input..................................................................500W ............................................600W
Drilling capacities:
Steel ............................................................13mm ............................................13mm
Wood ..........................................................30mm ............................................35mm
Concrete......................................................20mm ............................................24mm
Chuck type ....................................................SDS Plus ......................................SDS Plus
Speed (no load) ............................................0-950rpm ......................0-1100/0-2500rpm
Noise pressure level........................................83.5dbA ......................................85.5dbA
Noise power level ..........................................88.5dbA ......................................96.5dbA
Vibration level................................................12M/sec2 ....................................8.6M/sec2
Weight ..............................................................2.2kg ..............................................26kg
WEAR EAR PROTECTION
GUARANTEE (Hand held professional electric power tools)
Draper hand held professional electric power tools have been carefully tested and inspected
before shipment and are guaranteed to be free from defective materials and workmanship for
a period of 12 months from the date of purchase except where tools are hired out when the
guarantee period is reduced to ninety days from the date of purchase.
Should the machine develop any fault where warranty applies, arrangements will be made for
the tool to be returned free-of-charge to the Service Centre at Draper Tools Limited.
Please contact: DRAPER HELPLINE – 02380 494344
A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring is due to defective materials or
workmanship the product will be repaired and tested as soon as possible free of charge,
normally within five working days. This guarantee does not apply to normal wear and tear, nor
does it cover any damage caused by misuse, careless or unsafe handling, alterations, accident,
or repairs attempted by any personnel other than the Service Centre at Draper Tools Limited
or other authorised agent.
Note: If the tool is found not to be within the Terms of Warranty, repair and carriage charges
will be quoted and made accordingly.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of
its terms are not authorised.
Your Draper guarantee is not effective unless you produce a dated receipt or invoice to verify
your proof of purchase within the 12 month period.
Please note that this guarantee is an additional benefit and does not affect your statutory
rights.
Draper Tools Limited.
-2-
POWER SUPPLY
CONNECTING YOUR MACHINE TO THE POWER SUPPLY: (240V)
To eliminate the possibility of an electric shock your machine has been fitted with a BS approved,
non rewireable moulded plug and cable which incorporates a fuse, the value of which is indicated
on the pin face of the plug. Should the fuse need to be replaced an
approved BS1362 fuse
must be used of the same rating, marked thus
. The fuse cover is detachable, never use the
plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour
as that visible on the pin face of the plug (i.e. red). Fuse covers are available from your Draper Tools
stockist.
If the fitted plug is not suitable, it should be cut off and destroyed. *The end of the cable should now
be suitably prepared and the correct type of plug fitted. See below.
*WARNING:
A plug with bare flexible wires exposed is hazardous if engaged in a live power socket outlet.
WARNING: THIS APPLIANCE IS DOUBLE INSULATED.
Blue – Neutral, Brown – Live.
As these colours may not correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter
‘N’ or coloured black or blue.
The wire which is coloured brown must be connected to the terminal which is marked with the
letter ‘L’ or coloured red or brown.
CONNECTING YOUR MACHINE TO THE POWER SUPPLY (110V)
To eliminate the possibility of an electric shock your machine has been fitted with a BS approved,
rewireable plug and cable. If the fitted plug is not suitable, it should be removed, the end of the
cable should be suitably prepared and the correct type of plug fitted. See below.
WARNING: THIS APPLIANCE IS DOUBLE INSULATED.
Single phase 110 volt machines must be connected using the relevant coding and matching the
colour of the flexible cable to that of the plug. The procedure is as follows:
1. Connect brown coloured core to plug terminal marked letter ‘L’ (live).
2. Connect blue colour core to plug terminal marked letter ‘N’ (neutral).
WIRING DIAGRAM
PHD520VC
PHD624VC
-3-
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
WARNING
Please read the following instructions carefully, failure to do so could lead to serious personal injury.
IMPORTANT
Draper Tools Limited recommends that this machine should not be modified or used for any application other
than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in
writing and we will advise you.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool. Learn its application and limitations as
well as the specific potential hazards peculiar to this tool.
KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents. Floors must
not be slippery due to oil or sawdust.
AVOID DANGEROUS ENVIRONMENTS
Do not use power tools in damp or wet locations, or
expose them to rain. Keep work area well lit. Provide
adequate space surrounding the work area. Do not use in
environments with a potentially explosive atmosphere.
KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work area.
STORED TOOLS
When not being used, all tools should be stored in a dry,
locked cupboard or out of the reach of children.
WEAR PROPER CLOTHING
Do not wear loose clothing, neckties or jewellery (rings,
wristwatches) to catch in moving parts. NONSLIP footwear
is recommended.Wear protective hair covering to contain
long hair. Roll long sleeves above the elbow.
USE SAFETY GOGGLES (Head Protection)
Wear CE approved safety goggles at all times. Normal
spectacles only have impact resistant lenses, they are
NOT safety glasses. Also, use face or dust mask if
application is dusty and ear protectors (plugs or muffs)
during extended periods of operation.
NOISE LEVELS
Some types of machines may have high noise levels when
working. In such cases ear protection must be worn.
VIBRATION LEVELS
Hand held power tools produce different vibration levels.
You should always refer to the specifications and relevant
Health and Safety guide.
DUST EXTRACTION
If your tool is fitted with a dust extraction fitting, always
ensure that it is connected and being used with a dust
extractor.Vacuum cleaners can be used if suitable for the
material being extracted.
PROTECT YOURSELF FROM ELECTRIC SHOCK
When working with power tools, avoid contact with any
earthed items (e.g. pipes, radiators, hobs and
refrigerators, etc.). If you are using a power tool in
extreme conditions (e.g. high humidity or generating
metal dust), always use an RCD (residual current device)
at the power socket.
STAY ALERT
Always watch what you are doing and use common sense.
Do not operate a power tool when you are tired or under
the influence of alcohol or drugs.
WHEN WORKING OUT OF DOORS
Only use extension leads designed for that purpose.
ACCESS TO MAINS SOCKET
If a stationary machine is fitted with a moulded plug and
cable, the machine should not be positioned so that
access to the mains socket is restricted.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
DISCONNECT POWER TO THE TOOL
When not in use, before servicing and when changing
accessories such as cutters, etc.
AVOID ACCIDENTAL STARTING
Make sure the switch is in the OFF position before
plugging the machine into the power supply.
NEVER LEAVE MACHINE RUNNING UNATTENDED
Turn power off. Do not leave machine until it comes to a
complete stop.
DO NOT ABUSE THE CORD
Never carry the tool by the power cable or pull it from
the socket. Keep the power cable away from heat, oil and
sharp edges.
NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the
cutting tool is accidentally contacted. Do not store
materials above or near the tool, so that it is necessary to
stand on the tool to reach them.
CHECK DAMAGED PARTS
Check for damage to parts, breakage of parts, mountings
and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly
repaired or replaced.
KEEP GUARDS IN PLACE
And in working order.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for the best and safest
performance. Follow instructions for lubricating and
changing accessories. All extension cables must be
checked at regular intervals and replaced if damaged.
Always keep the hand grips on the tool clean, dry and
free of oil and grease.
USE RECOMMENDED ACCESSORIES
Consult the owners manual for recommended
accessories. Follow the instructions that accompany the
accessories. The use of improper accessories may cause
hazards.
REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
SECURE WORK
Use clamps or a vice to hold work. This frees both hands
to operate the tool.
DO NOT OVERREACH
Keep proper footing and balance at all times.
USE RIGHT TOOL
Do not force the tool or attachment to do a job for which it
was not designed.
DO NOT FORCE TOOL
It will do the job better and safer at the rate for which it
was designed.
DIRECTION OF FEED
Feed work into a blade or cutter against the direction of
rotation of the blade or cutter only.
WHEN DRILLING OR SCREWING INTO WALLS
Always make sure there is no danger of hitting any hidden
power cables, water or gas pipes in the wall.
IMPORTANT NOTE
Residual Risk. Although the safety instructions and operating manuals for our tools contain extensive
instructions on safe working with power tools, every power tool involves a certain residual risk which can not be
completely excluded by safety mechanisms. Power tools must therefore always be operated with caution !
-4-
GETTING TO KNOW YOUR
SDS+ ROTARY HAMMER DRILL
✗✌
✖✌
✕✘✌
✘✌
✙✌
✚✌
✕✌
✛✌
✕✕✌
✙✌
✕✔✌
✜✌
✕✖✌
✕✙✌
PHD520VC
✗✌
✖✌
✘✌
✕✘✌
✕✗✌
✙✌
✚✌
✕✌
✛✌
✕✕✌
✢✌
✕✔✌
✜✌
✕✖✌
✕✙✌
1. Tool Holder
2. Dust Protection Cap
3. Unlocking Collar
4. Side Handle Clamping Screw
5. Ventilation Slots
6. Rotational Direction Switch
7. Switch Locking Button
8. On-Off Switch
9.
10.
11.
12.
13.
14.
15.
PHD624VC
Speed Regulating Knob (240v only)
Drilling/Impact Select Knob
Depth Stop
Adjustable Handle
Gear Selector/Rotation Stop Switch
Ventilation Slots
Power Cable
-5-
OPERATION & USE
IMPORTANT: Check before plugging in that the
mains voltage agrees with the voltage specified
on the rating plate of the machine.
SWITCH
The switch ✪✌ on both of these tools is fitted with
a locking device, ✫✌ allowing the tool to be
operated for long periods of time without
interruptions. (Figs.2a and 2b).
Before inserting the plug into the socket, check that
the switch is in the unlocked position.When the
tool is not to be used for long periods remember to
leave the switch device in the unlocked position.
SPEED REGULATION (PHD 624VC)
An electronic speed regulation system has been
fitted to model PHD 624VC. Speed regulation is by
means of the knob ✮✌ and trigger ✪✌. Turn the
knob ✮✌ in the “A” direction and squeeze the
trigger ✪✌ slowly results in speeds from 0 to the
slowest pre-selected speed. Turn the knob ✮✌ in
the “G” direction and squeeze the trigger ✪✌
slowly results in speeds from 0 to the fastest
pre-selected speed. For variable speed set knob
✮✌ at the maximum position and use the trigger
✪✌ only. NOTE: Variable speed set knob ✮✌ is
fitted to 240v machine only (Fig.2b).
MECHANICAL GEAR SELECTION
(PHD624VC ONLY)
With the gear selector/rotation stop switch ✬✌
one of three positions can be selected. Fig.3.
1
= Lower speed range: hammer drilling,
drilling with normal twist drills in wood/
metal over 8mm dia. and mixing work.
2
= Higher speed range: drilling with
normal twist drills to 8mm dia.
= No rotation: light chiselling work.
The switch-over must be performed when the
machine is at a standstill. Please observe that the
gear selector/rotation stop switch ✬✌ can be
switched only one step at a time. Only after the
on/off switch ✪✌ (Fig.2) is actuated and the machine
starts does the gearbox shift to the selected mode.
The gear selector/rotation stop switch ✬✌ can only
then be switched again to the next position.
DRILLING – IMPACT DRILLING
For drilling, place the selector ✭✌ in the
position.
NOTE: Only use twist drills with chuck and adaptor.
For impact drilling, set to
(Fig.4).
The switch-over must be performed when the
machine is at a standstill. Only after the on/off
switch ✪✌ (Fig.2). is actuated and the machine
starts does the gear box shift to the selected mode.
Note: Left rotation when impact drilling damages
the drill. Switch off the impact mechanism for
diamond core drilling or for mixing work.
SPEED CONTROL
With the on/off switch ✪✌ the speed can be
continuously varied. With light pressure on the
on/off switch ✪✌ the machine begins to rotate
slowly; with increased pressure, the speed
increases. (Fig.2a).
✯✌
✯✌
✮✌
✪✌
✪✌
✫✌
Fig.2a.
Fig.2b. ✫✌
Fig.3.
✬✌
Fig.4.
✭✌
ROTATIONAL DIRECTION SWITCHING
Operate the rotational direction switch ✯✌ only
when the machine is at a standstill! (Figs.2a & 2b).
Take hold of the rotational direction switch ✯✌ on
both sides.
Right rotation: Set the rotational direction switch
✯✌ to “R”.
Left rotation: Set the rotational direction switch
✯✌ to “L”.
IMPORTANT:
Press the rotational direction switch ✯✌ in each
case to the stop on the housing ie. until it can be
felt to engage.
If the rotational direction switch ✯✌ is set
between the positions “R” and “L” the machine
cannot be switched on.
-6-
OPERATION & USE
INSERTING TOOLS
WARNING
Disconnect the plug from the power supply
socket before replacing drill bits or tools.
The tool holder ✰✌ clamps drilling and chiselling
tools without using a chuck key.
Pull back the unlocking collar ✳✌. Insert the tool
while turning into the tool holder ✰✌ until it
latches. Release the unlocking collar. Check
whether the tool is firmly seated. Fig.5.
Fig.5.
IMPORTANT
Always clean and lightly grease the tool shaft
before inserting into the chuck.
Take care that the dust protection cap ✱✌ is not
damaged. Fig.5.
Replace damaged dust protection caps
immediately or gearbox problems will ensue !
✰✌
✱✌
✳✌
REMOVING TOOLS
Slide the unlocking collar ✳✌ to the rear and pull
out the tool. Fig.5.
ADJUSTING THE CHISEL (PHD624VC ONLY)
Set the gear selector/rotation stop switch ✬✌ to an
intermediate position. The chisel can now be turned
by hand to the required working position. Fig.3.
Return the gear selector/rotation stop switch ✬✌
to the initial position
. The chisel latches
automatically as soon as it is radially loaded by
the working or chiselling process.
Fig.6.
✰✌
SLIP CLUTCH
If the drill bit becomes jammed or gets caught,
the clutch will slip.
Remove the load from the machine immediately
by pulling back the drill bit.
Always hold the machine tightely with both hands
and assume a secure stance.
Do not apply too much pressure. The performance
is not increased in this manner.
The most effective method for chiselling is to
break out only small pieces of material.
PHD624VC only.
✴✌
✵✌
SDS-PLUS
DRILL CHUCK (ACCESSORY)
For drilling work in metal, wood and plastic with
drills that have normal shafts, a drill chuck (13mm
max. chuck opening) is available. The drill chuck
is mounted on the adapter (accessory) for
screwdriver bits. All common drill chucks ✵✌ with
1
⁄2" x 20 UNF internal threads (13mm max. chuck
opening) can be used (Fig.6).
FITTING THE CHUCK
Clean the threads of the drill chuck ✵✌
(accessory) and the adapter ✴✌ (accessory).
Fig.6.
Screw the drill chuck onto the adapter ✴✌ and
lock the adapter ✴✌ in the same manner as a drill
in the tool holder ✰✌. To tighten a keyless drill
chuck, set the gear selector/rotation stop switch
✬✌ (Fig.3) temporarily to position
.
-7-
IMPROPER USE
The functions and use of this tool are those
exclusively indicated in this manual.
ANY OTHER USE OF THE TOOL IS
EXPLICITY FORBIDDEN.
MAINTENANCE &
PART REPLACEMENT
Regular inspection and cleaning reduces the
necessity for maintenance operations and will
keep your tool in good working condition. The
tool bearings and gears are life-long lubricated,
however it is advised to check the condition of the
grease in the head every 100 hours, if necessary
replace the grease. The motor must be correctly
ventilated during tool operation. For this reason
avoid blocking the air inlets with hands. After use
disconnect the tool from the power supply and
clean carefully, use compressed air through
ventilation slots.
DISPOSAL
At the end of the machine’s working life, or when
it can no longer be repaired, ensure that it is
disposed of according to the standard regulations
of the country in which it is being used, and that
the disposal operation is carried out by
specialized personnel following authorized
guidelines.
In all circumstances:
- Do not abandon in the environment;
- Do not dispose of together with solid urban
waste products;
- Contact the special recycling centres.
WARNING
Disconnect the plug from the power supply socket
before replacing any parts.
BRUSHES
The brushes must be replaced after approx. 150200 working hours, or if they are less then 5-6mm
in length.
WARNING
For correct tool operation always change the
brushes in pairs, not separately. The use of
original Draper spare parts is recommended.
After having fitted new brushes allow the motor to
run for at least five minutes without load for the
brushes to bed.
IMPORTANT:
This operation should only be performed by an
authorized person.
REPLACING THE POWER SUPPLY CABLE
Check that the power supply cable is in good
condition, if not have it replaced by an authorized
person.
-8-
OPTIONAL ACCESSORIES
1
2
3
4
5
6
FOR USE
WITH
MODEL
PHD624VC
ONLY
7
8
KEY No. PART No. STOCK No. DESCRIPTION
1
2
3
4
5
6
7
8
APT2
58590
SEE DRAPER CATALOGUE
APT3
58597
APT4
58598
SEE DRAPER CATALOGUE
APT6
58600
APT5
58599
APT7
58607
-9-
SDS Chuck Adaptor 1/2 × 20
Driver Bit
13 mm Keyless Chuck 1/2 × 20
13 mm Geared Chuck 1/2 × 20
SDS Masonry Drill
Point Chisel (for PHD 624 VC only)
Flat Chisel (for PHD 624 VC only)
Groove/Gouge Chisel (for PHD 624 VC only
NOTES
-9-
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,
Eastleigh, Hants. SO53 1YF. England.
Tel: (02380) 266355.
Fax: (02380) 260784.
HELPLINE 02380 494344
YOUR DRAPER STOCKIST
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in
any form or by any means, electronic, mechanical
photocopying, recording or otherwise without prior
permission in writing from Draper Tools Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising