Schneider Electric | EH450 | Trio EB450 Specifications - Industry Surplus Australia

Trio EB450 Specifications - Industry Surplus Australia
Trio E-Series
Licensed Ethernet and Serial
Base Station Radios
EB45e | EB450
1
Trio E-Series advanced digital data radios provide both
Ethernet and serial communications for the most complex
and demanding applications in Point-to-Point and Point-toMultipoint (Multiple Address Radio) Telemetry and remote
SCADA systems.
Base/Repeater stations are key elements in radio
communication systems and are subject to high dutycycle operational stresses. Trio EB45e, with Ethernet+serial
interfaces, and EB450 with serial-only interfaces, are full
duplex digital radio Base/Repeater stations specially designed
to complement Trio ER45e and ER450 remote digital data
radios by reliably delivering continuous duty operation at
maximum rated output power in ambient temperatures up to
+60°C (140°F).
The EB450 may be user-configured for operation in either
E-Series or M-Series modes. Where 1+1 redundancy
protection is required, the Trio EH45e and EH450 hot standby
Base/Repeater stations are available.
2
Product Data Sheet Trio EB450 & EB45e
Specifications
Trio EB45e
Radio
Frequency Range
380-520MHz (various sub-frequency bands available)
Frequency Splits
Various Tx/Rx frequency splits - configurable
Channel Selection
Dual synthesizer, 6.25kHz channel step
Channel Spacing
12.5 or 25kHz
Frequency Accuracy
±1ppm, -30 to +60°C (-22 to 140°F) ambient
Aging
<= 1ppm/annum
Radio Modes
Full and Half duplex, Simplex (Simplex requires separate TX/RX antennas)
Duplexer
Optional external duplexer available for single antenna operation
Configuration
All configuration via Windows based software
Transmitter
Tx Power
• 5W Model : 1W to 5W (+30 to +37dBm) +/- 1dB configurable with over-temperature and high VSWR protection
• 20W Model : 5W to 20W (+37 to +43dBm) +/- 1dB configurable with over-temperature and high VSWR protection
Modulation
Configurable narrow band digitally filtered binary GMSK or 4 level FSK
Tx Keyup Time
< 2mS
Timeout Timer
Configurable 0 to 255 seconds
Tx Spurious
<= -37dBm
PTT Control
Auto (Data) / RTS line (Data Port) / System Port Override / Permanent Tx
Receiver
Sensitivity
-118dBm for 12dB SINAD
Selectivity
Better than 60dB
Intermodulation
Better than 70dB
Spurious Response
Better than 70dB
AFC Tracking
Digital receiver frequency tracking
Mute
Programmable digital mute
Connections
Serial Data Port
RS232 DB9 female DCE. 300-38,400bps asynchronous
Serial Data Port Flow Control
Configurable hardware / software / 3-wire interface
Serial Data Port DCD Control
Configurable DCD operation : activated on RF carrier or from user data output
System Port
2 x RS232 RJ45 (Front & Rear): 19,200bps, for configuration and diagnostics
Ethernet Port
1 x RJ45: 10/100 Mbps (auto-MDIX sensing) compliant with IEEE 802.3
Digital I/O
2 Inputs monitored by TView+ Diagnostics Software, 2 outputs user-configurable by TView+ Diagnostics Software
Antenna
2 x N female bulkhead (separate Tx and Rx ports)
Power
2-pin locking, mating connector supplied
LED Display
Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs (for both Ethernet and Serial ports)
Bargraphs Indicators for Supply Volts, Tx Power, Drive Power, Receive Signal Strength and Frequency Error
Ethernet
Ethernet Protocols
Ethernet/IP (including UDP, TCP, DHCP, ARP, ICMP, STP, IGMP, SNTP & TFPT)
Ethernet Repeating
Automatic and Self Learning Peer to Peer repeating
Ethernet Traffic Filtering
Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only
Ethernet Link Monitoring
Monitor the Ethernet link between a base unit and up to two remote IP addresses
Compression
Automatic Ethernet data compression
Terminal Server
Legacy RS-232 serial support via embedded terminal server (UDP/TCP)
DHCP Modes
Auto and Manual
SNMP
SNMP V1/V2c, RFC1213-compliant and Trio Ethernet E-Series radio diagnostics parameters (including alarm generation
via traps)
Modbus Gateway
Configurable Modbus TCP/IP to Modbus Serial Gateway
Specifications continue on the next page
3
Product Data Sheet Trio EB450 & EB45e
Specifications
Trio EB45e
Modem
RF Channel Data Rate#
•
•
•
•
•
Typical Bit Error Rate#
< 1x10-6 @ -111dBm (4800bps), < 1x10-6 @ -110dBm (9600bps), < 1x10-6 @ -106dBm (19,200bps)
Operating Modes
Base, remote, repeater or store n’ forward
Channelshare™
Trio’s unique supervisory collision avoidance system
Multistream™
Simultaneous data stream delivery allows for multiple vendor devices/protocols to be transported on the one radio network
Data Turnaround Time
<10mS
Firmware
Local and over-the-air flash-based firmware upgradeable patches with support for broadcast updates
Radio Model F01 : FCC (IC) 9600bps (12.5kHz) & 19200bps (12.5kHz) North America
Radio Model F02 : 19200bps (25kHz)
Radio Model E01 : ETSI 4800bps (12.5kHz) & 9600bps (12.5kHz) Europe
Radio Model A01 : ACMA 4800bps (12.5kHz) / 9600bps (12.5kHz) Australia
Radio Model A02 : ACMA 19200bps (25kHz) Australia
Security
Encryption*
128-bit AES
Password Protection
Password protected configuration sessions
Diagnostics
Diagnostics Overview
•
•
•
•
•
•
•
•
•
TView+ configuration, network management and diagnostic Windows GUI software
Network-wide operation from any remote terminal
Non intrusive protocol – runs simultaneously with the application
SNMP access to radio diagnostics
Serial & Ethernet (eDiags) connectivity for diagnostics and configuration
Over-the-air re-configuration of user parameters.
Storage of data error and channel occupancy statistics
In-built Error Rate testing capabilities
Diagnostics parameters available
• Transmitter Power
• Received Signal Strength
• DC Supply Voltage
• Received Frequency Error
• Radio Temperature
• VSWR
General
Operating Temperature Range
-30°C to +60°C (-22°F to +140°F)
Power Supply
13.8Vdc nominal (11-16Vdc)
Transmit Current
• 5W Version: 1.3A nominal @ 1W, 2.5A nominal @ 5W
• 20W Version: 2.7A nominal @ 5W, 4.7A nominal @ 20W
Receive Current
< 350mA nominal @ 13.8Vdc
Dimensions
• 5W: 19” 2 RU rack mount, 483 x 90 x 414 mm including heat-sink (19 x 3.5 x 16.3in.)
• 20W: 19” 2 RU rack mount, 483 x 90 x 446 mm including heat-sink (19 x 3.5 x 17.6in.)
Weight
5.25kg (11.6lbs) excluding optional duplexer
Approvals and Certifications
Europe (ETSI)
ETSI EN300113, EN301489, EN60950
FCC
FCC PART 15, PART 90
Industry Canada
IC RS119, ICES-001
Australia
ACMA AS4295-1995 (Data)
* Export restrictions may apply. Contact your local representative for more details.
# Local radio regulatory requirements may dictate the actual RF channel data rate and Bit Error Rates available. Contact your local representative for more details
Note: Not all product features are available in every mode of operation.
Disclaimer: Schneider Electric reserves the right to change product specifications. For more information visit www.schneider-electric.com.
4
Product Data Sheet Trio EB450 & EB45e
Specifications
Trio EB450
Radio
Frequency Range
380-520MHz (various sub-frequency bands available)
Frequency Splits
Various Tx/Rx frequency splits - configurable
Channel Selection
Dual synthesizer, 6.25kHz channel step
Channel Spacing
12.5 or 25kHz
Frequency Accuracy
±1ppm, -30 to +60°C (-22 to 140°F) ambient
Aging
<= 1ppm/annum
Radio Modes
Full and Half duplex, Simplex (Simplex requires separate TX/RX antennas)
Duplexer
Optional external duplexer available for single antenna operation
Configuration
All configuration via Windows based software
Transmitter
Tx Power
• 5W Model : 1W to 5W (+30 to +37dBm) +/- 1dB configurable with over-temperature and high VSWR protection
• 20W Model : 5W to 20W (+37 to +43dBm) +/- 1dB configurable with over-temperature and high VSWR protection
Modulation
Configurable narrow band digitally filtered binary GMSK or 4 level FSK
Tx Keyup Time
< 2mS
Timeout Timer
Configurable 0 to 255 seconds
Tx Spurious
<= -37dBm
PTT Control
Auto (Data) / RTS line (Port A or B) / System Port Override / Permanent Tx
Receiver
Sensitivity
-118dBm for 12dB SINAD
Selectivity
Better than 60dB
Intermodulation
Better than 70dB
Spurious Response
Better than 70dB
AFC Tracking
Digital receiver frequency tracking
Mute
Configurable digital mute
Connections
Serial Data Port A
RS232 DB9 female DCE. 300-57,600bps asynchronous
Serial Data Port B
RS232 DB9 female DCE. 300-38,400bps asynchronous
Serial Data Port Flow Control
Configurable hardware / software / 3-wire interface
Serial Data Port DCD Control
Configurable DCD operation : activated on RF carrier or from user data output
System Port
2 x RS232 RJ45 (Front & Rear): 19,200bps, for configuration and diagnostics
Digital I/O
2 Inputs monitored by TView+ Diagnostics Software, 2 outputs user-configurable by TView+ Diagnostics Software
Antenna
2 x N female bulkhead (separate Tx and Rx ports)
Power
2-pin locking, mating connector supplied
LED Display
Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs (for both port A and B)
Bargraphs Indicators for Supply Volts, Tx Power, Drive Power, Receive Signal Strength and Frequency Error
Specifications continue on the next page
5
Product Data Sheet Trio EB450 & EB45e
Specifications
Trio EB450
Modem
RF Channel Data Rate#
•
•
•
•
•
Typical Bit Error Rate#
< 1x10-6 @ -111dBm (4800bps), < 1x10-6 @ -110dBm (9600bps), < 1x10-6 @ -106dBm (19,200bps)
Operating Modes
Base, remote, repeater or store n’ forward
Data Buffer
16kbyte of on-board RAM
Channelshare™
Trio’s unique supervisory collision avoidance system
Multistream™
Simultaneous data stream delivery allows for multiple vendor devices/protocols to be transported on the one radio network
Data Turnaround Time
<10mS
Firmware
Local flash-based firmware updates
Radio Model F01 : FCC (IC) 9600bps (12.5kHz) & 19200bps (12.5kHz) North America
Radio Model F02 : 19200bps (25kHz)
Radio Model E01 : ETSI 4800bps (12.5kHz) & 9600bps (12.5kHz) Europe
Radio Model A01 : ACMA 4800bps (12.5kHz) / 9600bps (12.5kHz) Australia
Radio Model A02 : ACMA 19200bps (25kHz) Australia
Security
Encryption*
128-bit AES
Password Protection
Password protected configuration sessions
Diagnostics
Diagnostics Overview
•
•
•
•
•
•
•
TView+ configuration, network management and diagnostic Windows GUI software
Network-wide operation from any remote terminal
Non intrusive protocol – runs simultaneously with the application
Over-the-air re-configuration of user parameters.
Storage of data error and channel occupancy statistics
In-built Error Rate testing capabilities
Diagnostics parameters available
• Transmitter Power
• Received Signal Strength
• DC Supply Voltage
• Received Frequency Error
• Radio Temperature
• VSWR
General
Operating Temperature Range
-30°C to +60°C (-22°F to +140°F)
Power Supply
13.8Vdc nominal (11-16Vdc)
Transmit Current
• 5W Version: 1.3A nominal @ 1W, 2.5A nominal @ 5W
• 20W Version: 2.7A nominal @ 5W, 4.7A nominal @ 20W
Receive Current
< 350mA nominal @ 13.8Vdc
Dimensions
• 5W: 19” 2 RU rack mount, 483 x 90 x 414 mm including heat-sink (19 x 3.5 x 16.3in.)
• 20W: 19” 2 RU rack mount, 483 x 90 x 446 mm including heat-sink (19 x 3.5 x 17.6in.)
Weight
5kg (11Ibs.) excluding optional duplexer
Approvals and Certifications
Europe (ETSI)
ETSI EN300113, EN301489, EN60950
FCC
FCC PART 15, PART 90
Industry Canada
IC RS119, ICES-001
Australia
ACMA AS4295-1995 (Data)
* Export restrictions may apply. Contact your local representative for more details.
# Local radio regulatory requirements may dictate the actual RF channel data rate and Bit Error Rates available. Contact your local representative for more details
Note: Not all product features are available in every mode of operation.
Disclaimer: Schneider Electric reserves the right to change product specifications. For more information visit www.schneider-electric.com.
6
Product Data Sheet Trio EB450 & EB45e
Model Code
EB45x-aabbb-cde represents the part number matrix
Model
Trio Radio EB450 & EB45e
TBURE
E-Series
Code
Select: Unit Type
B
Code
45
Code
0
E
Code
Base / Repeater Station
Select: Generic Frequency Band
380 to 518 MHz
Select: Data Ports
Two serial ports
One Ethernet & one serial port
Frequency (400MHz bands) – Frequencies to be specified at time of order
47
380 to 396 MHz (Tx & Rx)
48
395 to 406 MHz (Tx & Rx)
50
403 to 417 MHz (Tx & Rx)
63
406 to 421 MHz (Tx & Rx)
64
415 to 430 MHz (Tx & Rx)
56
418 to 435 MHz (Tx & Rx)
57
428 to 444 MHz (Tx & Rx)
55
436 to 450 MHz (Tx & Rx)
51
450 to 465 MHz (Tx & Rx)
65
455 to 470 MHz (Tx & Rx)
52
465 to 480 MHz (Tx & Rx)
53
480 to 494 MHz (Tx & Rx)
60
490 to 500 MHz (Tx & Rx)
54
505 to 518 MHz (Tx & Rx)
A6
370 to 400 MHz (Tx & Rx)
B3
395 to 426 MHz (Tx & Rx)
B4
413 to 447 MHz (Tx & Rx)
B5
433 to 450 MHz (Tx & Rx)
C1
436 to 467 MHz (Tx & Rx)
C2
450 to 487 MHz (Tx & Rx)
C3
Code
473 to 518 MHz (Tx & Rx)
Select: RF Channel Data Rate & Bandwidth (Internal Modem)
F01
FCC (IC) 9600 / 19k2bps, 12.5kHz – provides M-Series 003 compatability
F02
FCC (IC) 19k2bps, 25kHz – Not for sale in North America
E01
ETSI 9600bps, 12.5kHz – provides M-Series 004 compatability
A01
ACMA 4800 / 9600bps, 12.5kHz – provides M-Series 001/002 compatability
A02
ACMA 9600 / 19K2bps, 25kHz
Code
Select: Diagnostics & Encryption
D
Diagnostics Only (No Encryption)
E
Diagnostics & Encryption*
7
Product Data Sheet Trio EB450 & EB45e
Dimensions
Code
Select: Options
0
Separate Tx & Rx Antenna Ports
1
Configured for internal band reject duplexer. Duplexer not included. Contact local sales office for further details.
A
20W RF Power Output**
Code
0
Hot Standby Configuration
Not used
Communications Standards:
FCC – Federal Communications Commission (USA)
IC – Industry Canada
ETSI – European Telecommunication Standards Institute
ACMA – Australian Communication s and Media Authority
* Export restrictions may apply. Contact your local representative for more details.
** Local regulatory conditions may prevent the use of 20W in some countries.
Note: Some radio models may not be available in your country. Local and regulatory conditions may determine the performance and suitability of the radio in
different countries. It is the responsibility of the buyer to ensure the radio model meets the regulatory conditions required. Contact your local Schneider Electric
sales office for more details.
ON / OFF
[ LAN ] Link
[ Data ]
Rx
Green
14
16
Vdc
20
26
31
37
43
+10
+15
+20
+25
+30
TxPower
RxSig
dBm
TxDrive
dBm
-120
Data
TxD
12
Supply
Tx
Synch
System
Port
10
Status
DC Power
-100
-80
-60
RxSig
RxFreq. Offset
dBm
-4
-2
0
+2
+4
kHz
Red
19” (483mm)
Telemetry & Remote SCADA Solutions
| www.schneider-electric.com
Document Number TBULM08003-05
© 2011 Schneider Electric. All rights reserved - October 2012
Display
>
Trio EB45e
16.31" (414mm) 5W model
17.60" (446mm) 20W model
3.0” (76mm)
18.31” (465mm)
>
3.54” (90mm)
3.46” (88mm)
15” (381mm)
14.31” (361mm)
16.69” (424mm)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising