Chauvet | Model ST-200 | User manual | Chauvet Model ST-200 User manual

Chauvet Model ST-200 User manual
ST-200
Techno Strobe™ 200
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
TABLE OF CONTENT
BEFORE YOU BEGIN........................................................................................................................................................... 3
WHAT IS INCLUDED ................................................................................................................................................................................ 3
UNPACKING INSTRUCTIONS .................................................................................................................................................................... 3
SAFETY INSTRUCTIONS .......................................................................................................................................................................... 3
INTRODUCTION ................................................................................................................................................................... 4
FEATURES ............................................................................................................................................................................................ 4
PRODUCT OVERVIEW ............................................................................................................................................................................ 4
SETUP ................................................................................................................................................................................... 5
LAMP ................................................................................................................................................................................................... 5
Lamp installation ................................................................................................................................................................................................ 5
MOUNTING ........................................................................................................................................................................................... 6
Orientation .......................................................................................................................................................................................................... 6
Rigging ............................................................................................................................................................................................................... 6
USING A COLOR GEL ............................................................................................................................................................................. 6
OPERATING INSTRUCTIONS.............................................................................................................................................. 7
OPERATING MODES............................................................................................................................................................................... 7
Stand Alone ........................................................................................................................................................................................................ 7
Unison Strobe..................................................................................................................................................................................................... 7
APPENDIX............................................................................................................................................................................. 8
MAINTENANCE ...................................................................................................................................................................................... 8
RETURNS PROCEDURE .......................................................................................................................................................................... 8
CLAIMS ................................................................................................................................................................................................ 8
GENERAL TROUBLESHOOTING ................................................................................................................................................................ 9
TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 10
ST-200 User Manual
2
Revision: 2004-11-02/11:23
BEFORE YOU BEGIN
What is included
¾
¾
¾
¾
ST-200
Power cord with plug
200w Xenon lamp (Installed)
Warranty Card & Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Safety Instructions
Please read these instructions carefully, which
includes important information about the installation,
usage and maintenance?
•
•
•
•
•
•
•
•
•
•
•
•
•
Caution!
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage and that the line voltage you are
connecting to is not higher than that stated on decal or rear panel of the fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
Maximum ambient temperature is Ta: 40°. Do not operate fixture at temperatures higher than this.
In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
Don’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
Never disconnect power cord by pulling or tugging on the cord.
Avoid direct eye exposure to lamp.
There are no user serviceable parts inside the unit. Do not any repairs yourself. In
the unlikely event your unit may require service, please contact CHAUVET.
ST-200 User Manual
3
Revision: 2004-11-02/11:23
INTRODUCTION
Features
•
•
•
•
audio sensitivity adjustment
manual strobe speed control
manual strobe intensity control
1 year warranty
Product Overview
Hanging
bracket
Gel
Holder
Connect to
other ST-200
strobes for
unison
operation
Fuse compartment
Audio
sensitivity
adjustment
Strobe speed
adjustment
Strobe intensity
adjustment
ST-200 User Manual
4
¼” Phone plug
for simple
variable speed
remote control
(Use SC-1000M
or CH-751)
Revision: 2004-11-02/11:23
SETUP
Lamp
The xenon 200 watt lamp comes pre-installed from the factory.
Warning!
When replacing the lamp, please wait 15 minutes after powering down to allow the
unit to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.
LA M P IN STA LLA T ION
1)
Unscrew the three most left and right screws on the back of the ST-200X and lift the front cover
carefully. The segment display can remain attached to the PCB during lamp replacement.
2)
Unscrew the three lamp wires from their respective terminals on the PCB as illustrated in Figure
3. You may need to clip the tie-wraps that restrain the loose wires to the screw posts on the PCB
in order to free the lamp.
3)
Slide lamp socket out of the thin metal plate one end at a time.
4)
Replace strobe with new lamp and re-fasten wires to the terminals. (CHAUVET lamp model #
BL-200ST)
Top view
ST-200 Lamp Installation
Lamp side with 2 wires;
Lamp side with 1
wire molded into
ceramic base
gets fastened to
terminal labeled
J3.
J3
5)
ST-200 User Manual
J4
1.
Wire molded into
ceramic base is
fastened to
terminal labeled J4
2.
Wire coiled around
the envelope of the
bulb gets fastened
to terminal labeled
J5.
J5
Replace front cover and screws.
5
Revision: 2004-11-02/11:23
Setup
Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation. It is also
possible to stand this fixture using the removable feet provided.
R IG G IN G
Figure 1 - Hanging Bracket
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding
the desired position, retighten both knobs.
•
•
•
When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
Safety cables should always be used.
Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
Note!
Clamp is sold separately.
Using a Color Gel
The ST-200 is equipped with a detachable clear front cover that doubles as a gel holder as illustrated
below.
1)
Open the clear lamp cover by removing the thumbscrew.
2)
Cut a piece of gel filter to match the size of the cover or slightly
larger. The size of the gel used in the illustration was a 6.5” by
6.5”.
3)
Lay the gel over the opening, close cover and replace the
thumbscrew securely.
ST-200 User Manual
6
Revision: 2004-11-02/11:23
OPERATING INSTRUCTIONS
Operating Modes
•
•
A stand-alone mode will listen to sound and strobe to the beat.
Master/Slave output provides for unison triggering of chained strobes.
STAND ALONE
The Stand Alone mode is activated automatically when the fixture is absent of a CH-751 or a SC1000M controller. The strobe speed, strobe intensity and the microphone sensitivity can all be
adjusted and they are located on the bottom of the ST-200.
UN I SON STR OB E
The Unison strobe mode will allow you to link additional units in a daisy chain fashion. Simply connect
each fixture in a daisy like fashion using a ¼” MONO phone cable.
Daisy Chain Connection
Optional Controller
ST-200 User Manual
7
Revision: 2004-11-02/11:23
APPENDIX
Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
ST-200 User Manual
8
Revision: 2004-11-02/11:23
Appendix
General Troubleshooting
Applies to
Symptom
Solution(s)
Lights
Auto shut off
Check fan thermal switch reset
9
Beam is very dim or not
bright
Clean optical system or replace lamp
Breaker/Fuse keeps
blowing
Check total load placed on device
Chase is too slow
Check users manual for speed adjustment
Device has no power
Check for power on Mains.
Foggers
& Snow
Controllers
Dimmers
& Chaser
9
Check 220/110v switch for proper setting
9
9
9
9
9
9
9
9
9
9
9
9
Check device’s fuse. (internal and/or external)
Fixture is on but there
is no movement to the
audio
Make sure you have the correct audio mode on the control
switches. If audio provided via ¼” jack, make sure a live
audio signal exists
Adjust sound sensitivity knob
Lamps cuts off
sporadically
Possible bad lamp or fixture is overheating.
Light will not come on
after power failure
Some discharge lamps require a cooling off period before
the electronics in the fixture can kick start it again, wait 5 to
10 minutes before powering up
Loss of signal
Use only DMX cables
9
Lamp may be at end of its life.
9
Install terminator
Note: Keep DMX cables separated from power cables or
black lights.
9
Moves slow
Check 220/110v switch for proper setting
9
No flash
Re-install bulb, may have shifted in shipping
9
No light output
Check slip ring & brushes for contact
9
9
Install bulb
Call service technician
Relay will not work
Check reset switch
9
Check cable connections
Remote does not work
Make sure connector is firmly connected to device
9
Stand alone mode
All Chauvet lighting fixtures featuring stand-alone functions
do not require additional settings, simply power the fixture
and it will automatically enter into this mode
9
ST-200 User Manual
9
9
Revision: 2004-11-02/11:23
Appendix
Technical Specifications
WEIGHT & DIMENSIONS
Length.............................................................................................................................. 330 mm (13 in)
Width .............................................................................................................................. 205 mm (8.1 in)
Height .................................................................................................................................100 mm (4 in)
Weight ........................................................................................................................ 2.24 Kg (4.93 lbs)
POWER
Operating Range ...........................................................................................115V 60 Hz or 230V 50 Hz
AC input............................................................................................................ 3 prongs IEC 60320 C14
LAMP
Xenon (BL-200ST) ......................................................................................................................... 200W
THERMAL
Maximum ambient temperature............................................................................................ 40° (104° F)
FUSE
Main............................................................................................................... 20mm Glass 3A Fast Blow
CONTROL & PROGRAMMING
Remote Controller Input ....................................................................................... ¼” MONO phone plug
Output................................................................................................................... ¼” MONO phone plug
ORDERING INFORMATION
Techno Strobe™ 200 ................................................................................................................... ST-200
Techno Strobe™ Replacement Bulb........................................................................................BL-200ST
1 Channel Strobe Controller ........................................................................................................ CH-751
4 Channel Strobe Controller ............................................................................................. SC-1000mono
Fuse 3A ............................................................................................................................P170FUSE003
ST-200 User Manual
10
Revision: 2004-11-02/11:23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising