Yamaha | DSP-A590 | Owner`s manual | Yamaha DSP-A590 Owner's manual

Yamaha DSP-A590 Owner's manual
DSP-A590
Natural Sound Digital Sound Field Processing Amplifier
Amplificateur de champ sonore numérique de la série “Natural Sound”
Natural Sound Digitaler Klangfeldverstärker
Digital ljudfältsförstärkare med naturligt ljud
Amplificatore digitale a suono naturale per l’elaborazione del campo sonoro
Amplificador de procesamiento de campo de sonido digital de Sonido natural
Digitale geluidsveldprocessing-versterker met natuurlijke klank
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
SUPPLIED ACCESSORIES
ACCESSOIRES FOURNIS
MITGELIEFERTE ZUBEHORTEILE
MEDFOLJANDE TILLBEHOR
ACCESSORI IN DOTAZIONE
ACCESORIOS INCLUIDOS
BIJGELEVERDE ACCESSOIRES
●
●
●
●
●
●
●
Remote Control Transmitter
Emetteur de télécommande
Fernbedienungsgeber
Fjärrkontrollsändare
Telecomando
Transmisor del control remoto
Afstandbediening
●
●
●
●
●
●
●
After unpacking, check that the following parts are included.
Après le déballage, vérifier que les pièces suivantes sont incluses.
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
Kontrollera efter det apparaten packats upp att följande delar finns med.
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
Desembale el aparato y verificar que los siguientes accesorios están en la caja.
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
●
●
●
●
●
●
●
Batteries (size AA, R6, UM-3)
Piles (taille AA, R6, UM-3)
Batterien (Größe AA, R6, UM-3)
Batterier (storlek AA, R6, UM-3)
Batterie (dimensioni AA, R6, UM-3)
Pilas (tamaño AA, R6, UM-3)
Batterijen (maat AA, R6, UM-3)
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or
87/308/EEC.
Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE.
Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.
Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj.
Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi.
Este producto está de acuerdo con los requisitos sobre interferencias de radio frecuencia fijados por el Consejo Directivo
87/308 CEE.
Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.
2
FEATURES
● 5 Speaker Configuration
Front: 70W + 70W (8Ω) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: 70W (8Ω) RMS Output Power,
0,07% THD, 20–20,000 Hz
Rear: 20W + 20W (8Ω) RMS Output
Power, 0.3% THD, 1 kHz
● Automatic Input Balance Control for
Dolby Surround
● Digital Sound Field Processor
6 Programs for Digital Sound Field
Processing
2 Programs for Dolby Surround Decoding
(DOLBY PRO LOGIC and DOLBY PRO
LOGIC ENHANCED)
● Video Signal Input/Output Capability
(Including S Video Connections)
English
Thank you for selecting this YAMAHA digital sound field processing amplifier.
● Test Tone Generator for Easier Speaker
Output Balance Adjustment
● 3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
● SLEEP Timer
● Remote Control Capability
CONTENTS
Supplied Accessories ......................................2
Using Digital Sound Field Processor (DSP) ..18
Caution ............................................................4
Setting the SLEEP Timer ..............................22
Profile of This Unit ...........................................5
Remote Control Transmitter ..........................23
Speaker Setup for This Unit ............................6
Notes about the Remote Control Transmitter
Connections ....................................................7
.......................................................................24
Speaker Balance Adjustment ........................12
Troubleshooting .............................................25
Basic Operations ...........................................15
Specifications ................................................26
3
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
1.
2.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
3.
Never open the cabinet. If something drops into the set, contact
your dealer.
4.
Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wires themselves.
5.
The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
For U.K. customers
6.
Always set the VOLUME control to “– ∞” before starting the audio
source play. Increase the volume gradually to an appropriate level
after playback has been started.
7.
Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note: The plug severed from the mains lead must be destroyed,
as a plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
8.
Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
Special Instructions for U.K. Model
9.
When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
10. To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
11. Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12. AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
13. Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
4
IMPORTANT
Please record the serial number of this unit in the space below.
IMPORTANT
THE WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the main lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The wire
which is coloured BROWN must be connected to the terminal which
is marked with the letter L or coloured RED. Make sure that neither
core is connected to the earth terminal of the three pin plug.
You are the proud owner of a Yamaha stereo amplifier –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
English
PROFILE OF THIS UNIT
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
What’s more, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets you
experience the dramatic realism and impact of Dolby Surround
movie theater sound in your own home. Dolby Pro Logic gets
its name from its professional-grade steering logic circuitry,
which provides greater effective front and rear channel
separation for a much higher degree of realism than the
“passive” Dolby Surround circuits found in less sophisticated
home audio/video equipment. Dolby Pro Logic Surround
provides a true center channel, so that there are four
independent channels, unlike passive Dolby Surround which
has in effect only three channels: left, right, and rear. This
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from action on the
screen while getting a stereo effect as well.
Dolby Pro Logic Surround + DSP
You can also enjoy a combination of Dolby Pro Logic Surround
and DSP in the sound field program “
PRO LOGIC
ENHANCED”.
It recreates the surround effect of a movie theater, effectively
duplicating its multiple surround loudspeaker system,
completely surrounding the listener with the sounds of the
action taking place on the screen.
5
SPEAKER SETUP FOR THIS UNIT
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The speakers to be used with this unit
will be mainly front speakers, rear speakers, and a center speaker. (You can omit the center speaker. Refer to the “4-Speaker
Configuration” shown below.)
The front speakers are used for the main source sound and the effect sound. They will probably be the speakers of your present
stereo speaker system. The rear speakers are used for the effect sound. And the center speaker is used for the center sound
(dialog etc.) encoded with the Dolby Surround. The rear and center speakers do not need to be equal in power to the front
speakers. However, all the speakers should have high enough power handling to accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
4-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the digital sound field program DOLBY
PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected,
conversations will be output from the center speaker and the
ambience will be excellent.
● Set the center channel mode to the “NORMAL” or “WIDE”
position. (For details, refer to page 13.)
The center speaker is not used in this configuration. If the
digital sound field program DOLBY PRO LOGIC or DOLBY
PRO LOGIC ENHANCED is selected, the center sound is
output from the left and the right front speakers. However, the
sound effect of other programs can be the same as that of the
5-speaker configuration.
● Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 13.)
Front L
Center
Front R
Front L
Dialogue
Dialogue
Surround sound
Surround sound
Rear L
Rear R
Rear L
Front R
Rear R
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Front:
In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the front speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front R
Center
Front L
TV set
Rear R
Rear L
6
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
English
CONNECTIONS
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
LD player,
TV tuner, etc.
AUDIO IN
VIDEO OUT
AUDIO OUT
VIDEO IN
Video cassette recorder 2
VIDEO OUT
VIDEO IN
AUDIO OUT
Monitor TV
GND
OUTPUT
Turntable
(Europe model)
OUTPUT
8ΩMIN.
/SPEAKER
FRONT
CENTER
REAR
REAR
GND
AC OUTLETS
SWITCHED
l20W MAX. TOTAL
CENTER
C
D
DUAL
8 VIDEO
VCR 2
MONITOR
IN
OUT
OUT
C D:4ΩMIN./SPEAKER
SINGLE:8ΩMIN./SPEAKER
VIDEO SIGNAL
MONITOR LD/TV
OUT
VCR 1
IN
OUT
VCR 2
IN
OUT
MAINS
LOW
PASS
fc:200Hz
SINGLE
SPEAKERS
SPEAKERS
A
A
A OR B:8ΩMIN.
/SPEAKER
A B:l6ΩMIN.
/SPEAKER
B
PHONO
CD
TUNER
TAPE
REC
PB
OUT
TAPE
IN
LD/TV
OUT
VCR 1
IN
B
OUT
VCR 2
-l0 dB 0 dB
FRONT
LEVEL
FRONT
AUDIO SIGNAL
CD player
Tuner
Tape deck
VIDEO IN
AUDIO IN
AUDIO OUT
VIDEO OUT
LINE IN
LINE OUT
OUTPUT
OUTPUT
To AC outlet
Video cassette recorder 1
: Refer to “ABOUT THE ACCESSORY TERMINALS” on page 11.
7
CONNECTING TO S VIDEO TERMINALS
If you have a video cassette recorder and a monitor equipped with “S” (high-resolution) video terminals, those terminals can be
connected to this unit’s S VIDEO terminals. Connect the video cassette recorder’s “S” video input and output terminals to this unit’s
S VIDEO VCR 2 IN and OUT terminals respectively, and connect the monitor’s “S” video input terminal to this unit’s S VIDEO
MONITOR OUT terminal. Otherwise, connect the video cassette recorder’s composite video terminals to this unit’s composite video
terminals, and connect the monitor’s composite video input terminal to this unit’s composite MONITOR OUT terminal.
Note
If video signals are sent to both S VIDEO input and composite input terminals, the signals will be sent to their respective
output terminals independently.
Monitor TV
VIDEO SIGNAL
VCR 1
OUT
IN
VCR 2
OUT
VIDEO IN
IN
VIDEO OUT
MONITOR LD/TV
OUT
S VIDEO
IN
S VIDEO
VCR 2
MONITOR
OUT
IN
OUT
S VIDEO
OUT
S VIDEO
IN
VIDEO
IN
Video cassette recorder 2
CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)
These terminals are used to connect any video input source such as a camcorder to this unit.
VIDEO AUX
S VIDEO
VIDEO
L AUDIO R
AUDIO OUT R
R
AUDIO OUT L
VIDEO OUT
L
VIDEO
Camcorder
S VIDEO OUT
S VIDEO
8
English
CONNECTING SPEAKERS
Connect the respective speakers to this unit as figured below.
Rear speakers
Left
Right
OUTPUT
8ΩMIN.
/SPEAKER
FRONT
CENTER
REAR
REAR
CENTER
C
D
DUAL
C D:4ΩMIN./SPEAKER
SINGLE:8ΩMIN./SPEAKER
LOW
PASS
fc:200Hz
SINGLE
SPEAKERS
SPEAKERS
A
A
A OR B:8ΩMIN.
/SPEAKER
A B:l6ΩMIN.
/SPEAKER
B
B
Center speaker
-l0 dB 0 dB
FRONT
LEVEL
FRONT
Left
Right
FRONT LEVEL
switch
(U.K., Europe and
Australia models)
Front speakers A
Left
Right
Front speakers B
Note on front speaker connection:
Note on center speaker connection:
One or two speaker systems can be connected to this unit. If
you connect only one speaker system, connect it to either the
SPEAKERS A or B terminals.
One or two center speakers can be connected to this unit. If
you cannot place the center speaker on or under the TV, it is
recommended to use two center speakers and place them on
both sides of the TV to orient the center sound at the center
position. For connecting two center speakers, follow the
method shown below.
REAR
FRONT LEVEL switch
<U.K., Europe and Australia models only>
Normally set to “0 dB”. If desired, you can decrease the
output level at the FRONT SPEAKERS terminals by 10 dB by
setting this switch to “–10 dB”.
CENTER
C
D
DUAL
SINGLE
l
l0 dB 0 dB
FRONT
LEVEL
Center speaker
Center speaker
9
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
Note
Use speakers with the specified impedance shown on the rear
of this unit.
For connecting to the FRONT SPEAKERS terminals
Red: positive (+)
Black: negative (–)
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
➀ Unscrew the knob.
➁ Insert the bare wire.
2
1
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂ Tighten the knob and
secure the wire.
➀ Press up the tab.
➁ Insert the bare wire.
➀
➂
3
➁
*
<General model only>
Banana Plug connections are also possible. Simply insert
the Banana Plug connector into the corresponding terminal.
10
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂ Release the tab and
secure the wire.
English
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S) (SWITCHED)
FRONT OUTPUT terminals
(Europe and General models) .......... 2 SWITCHED OUTLETS
(U.K. and Australia models) ................ 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 120 watts.
These terminals are for front channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive front speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
REAR OUTPUT terminals
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
These terminals are for rear channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive rear speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
LOW PASS terminal
CENTER OUTPUT terminal
This terminal is for output to a monaural amplifier driving a
subwoofer. Only frequencies below 200 Hz from the front and
center channels are output.
This terminal is for center channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
GND terminal (For turntable use)
ADDING A SUBWOOFER
You may wish to add a subwoofer to reinforce the bass
frequencies.
Connect the LOW PASS terminal to the INPUT terminal of
the subwoofer amplifier, and connect the speaker terminals
of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
OUTPUT
FRONT
CENTER
REAR
LOW
PASS
fc:200Hz
Subwoofer system
11
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test
tone generator. With this adjustment, the sound output level heard at the listening position will be the same from each speaker.
This is important for the best performance of the digital sound field processor.
The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.
Otherwise, the result may not be satisfactory.
1
5
4
REC PAUSE
DIR A
PLAY
TEST
1
4
5
Set to the “ ∞ ” position.
VCR 2
EFFECT
ON/OFF
V AUX
VOLUME
DELAY TIME
POWER
Select the
PRO LOGIC or
PRO LOGIC
ENHANCED mode, so that the corresponding name is
illuminated on the display.
Select the front speakers to be used.
SPEAKERS
EFFECT
A
B
ON
ON
OFF
OFF
* If you use two front speaker systems, press both the A
and B switches.
3
BASS
l
0
TREBLE
l
2
l
2
3
3
4
4
5
5
0
BALANCE
l
2
l
2
3
3
4
4
5
5
Set to the “0” position.
12
HALL
DISCO
3
2
2
5
VCR 1
SUR.
MONO MOVIE STADIUM
ROCK
REAR
LEVEL
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
PRO LOGIC
CENTER
LEVEL
DIR B
STOP
0
l
2
2
3
3
4
4
L 5
5 R
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
DISCO
ROCK
CONCERT
CONCERT
HALL
English
8
6
REC PAUSE
7
DIR A
PLAY
TEST
STOP
CENTER
LEVEL
MONO MOVIE STADIUM
PRO LOGIC
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
VCR 1
SUR.
ROCK
REAR
LEVEL
DIR B
HALL
DELAY TIME
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
VOLUME
8
6
Select the center channel output mode according to your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 6.)
CENTER
MODE
7
TEST
TEST
ER
Flashes continuously.
NORMAL
WIDE
8
Turn up the volume.
PHANTOM
VOLUME
On the feature of each mode, refer to the “Note” shown
below.
Note
In step 6, when you select the center channel output mode,
note the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the front speakers. In this
mode, the bass tone will be output from the front
speakers.
WIDE:
Select this mode when you use the center speaker
approximately same sized as the front speakers.
You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two
seconds each. The display changes as shown below.
Front (L)
Center
TEST
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right front speakers.
Rear
(L and R)
Front (R)
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
CONTINUED
13
REC PAUSE
12
10
11
DIR A
TEST
PRO LOGIC
CENTER
LEVEL
DIR B
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
VCR 1
SUR.
MONO MOVIE STADIUM
ROCK
REAR
LEVEL
PLAY
STOP
HALL
DELAY TIME
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
VOLUME
9
9
12
Adjust the BALANCE control so that the effect sound
output level of the left front speaker and the right front
speaker are the same.
Cancel the test tone.
TEST
TEST
R
BALANCE
l
0
l
2
2
3
3
4
L 5
10
Stops flashing and disappears
4
5 R
Adjust the sound output level of the center speaker to
be at the same level as that of the front speakers with
the CENTER LEVEL keys.
Lights up.
TEST
CENTER
LEVEL
CENTER
00
Adjustable
11
Adjust the sound output level of the rear speakers to
be at the same level as that of the front speakers with
the REAR LEVEL keys.
Lights up.
TEST
REAR
LEVEL
0
REAR
Adjustable
14
Notes
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the VOLUME keys on the remote
control transmitter).
● If you use external power amplifiers, their volume controls
may also be adjusted to achieve proper balance.
● In step 10, if the center channel mode is in the
“PHANTOM” position, the sound output level of the center
speaker cannot be adjusted. This is because in this mode,
the center sound is automatically output from the left and
right front speakers.
● <U.K., Europe and Australia models only>
If there is insufficient sound output from the center and
rear speakers, you may decrease the front speaker output
level by setting the FRONT LEVEL switch on the rear
panel to “–10 dB”.
●
7
2
4
3
1, 6
English
BASIC OPERATIONS
7
TO PLAY A SOURCE
1
5
Play the source.
6
Set to the “ ∞ ” position.
2
POWER
Adjust to the desired output level.
7
3
Select the desired input source by using the input
selector buttons.
(For video sources, turn the TV/monitor ON.)
TAPE
MONITOR
TUNER
CD
PHONO
VIDEO AUX
VCR 2
VCR 1
LD/TV
* The name of the selected input source will appear in
the display.
4
Select the front speakers to be used.
SPEAKERS
A
B
ON
ON
OFF
OFF
If desired, adjust the BASS, TREBLE, BALANCE
controls, etc. (refer to page 17) and use the digital
sound field processor. (Refer to page 20.)
Notes on using the input selector buttons
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
* To select the source connected to the VIDEO AUX
terminals on the front panel, press VIDEO AUX.
● The selection of TAPE MONITOR cannot be canceled by
pressing another input selector button. To cancel it, press
TAPE MONITOR again.
When you select a button other than TAPE MONITOR,
make sure that TAPE MONITOR is not also selected.
● If you select the input selector button for a video source
without canceling the selection of TAPE MONITOR, the
playback result will be the video image from the video
source and the sound from the audio tape.
● Once you play a video source, its video image will not be
interrupted even if the input selector button for an audio
source is selected.
●
To turn off the power
Press the POWER switch again.
* If you use two front speaker systems, press both the A and
B switches.
15
1, 4
2
TO RECORD A SOURCE TO TAPE
(OR DUB FROM TAPE TO TAPE)
1
2
3
4
16
Note
DSP, VOLUME, BASS, TREBLE and BALANCE control
settings have no effect on the material being recorded.
Select the source to be recorded.
TAPE
MONITOR
TUNER
CD
PHONO
VIDEO AUX
VCR 2
VCR 1
LD/TV
Play the source and then turn the VOLUME control
up to confirm the input source.
Set the tape deck or VCR to the recording mode.
If the tape deck is used for recording, you can monitor
the sounds being recorded by pressing TAPE
MONITOR.
TAPE
MONITOR
TUNER
CD
PHONO
VIDEO AUX
VCR 2
VCR 1
LD/TV
Because one or two speaker systems (as front speakers) can
be connected to this unit, the SPEAKERS switches allow you
to select speaker system A or B, or both at once.
Adjusting the BASS and TREBLE
controls
BASS
l
0
TREBLE
l
2
SPEAKERS
A
B
ON
ON
OFF
OFF
3
3
4
BASS
l
2
4
5
English
Selecting the SPEAKER system
5
0
l
2
2
3
3
4
4
5
5
: Turn this clockwise to increase (or counterclockwise to decrease) the low frequency
response.
Adjusting the BALANCE control
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
BALANCE
l
0
l
2
2
3
TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency
response.
Note
These controls are effective only for the sound from the front
speakers.
3
4
4
L 5
5 R
Note
This control is effective only for the sound from the front
speakers.
When you listen with headphones
PHONES
Connect the headphones to the PHONES jack. You can listen
to the sound to be output from the front speakers through
headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
switch.
17
USING DIGITAL SOUND FIELD PROCESSOR (DSP)
This unit incorporates a sophisticated, multi-program digital sound field processor, which allows you to expand and shape the audio
sound field from both the audio and video sources, for a theater-like experience in the listening/viewing room.
This digital sound field processor has 8 programs; 6 programs for digital sound field processing and 2 programs for the Dolby Pro
Logic Surround sound system (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED). You can create an excellent audio
sound field by selecting the suitable program and adding desired adjustments. In addition, when the DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED program is selected, the built-in automatic input balance control functions. This presents you the
best surround condition without manual adjustment.
Front Panel
Displays your selection on the
DSP or other informations.
TEST
SLEEP
DELAY
CENTER
REAR
TAPE MONITOR
NORMAL WIDEPHANTOM
EFFECT
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
CENTER
MODE
Switches on/off the digital
sound field processor (DSP)
ms
PRO LOGIC CONCERT MONO STADIUM ROCK CONCERT
ENHANCED VIDEO MOVIE DISCO CONCERT HALL
STADIUM
DELAY TIME
DISCO
ROCK
CONCERT
CENTER LEVEL
CONCERT
HALL
REAR LEVEL
Selects a digital
sound field program.
Selects the center channel
output mode. (For details,
refer to page 13.)
Adjusts sound output
level at each speaker.
(For details, refer to
Adjusts the delay time. page 20 and 21.)
(For details, refer to
page 21.)
Remote Control Transmitter
POWER
SLEEP
PHONO
DISC
SKIP
SKIP
Used for speaker balance adjustment
(For details, refer to page 12, 13 and 14.)
DECK A/B
REC PAUSE
PAUSE/STOP
PRESET
DIR A
STOP
CENTER
LEVEL
MONO MOVIE STADIUM
PRO LOGIC
Adjusts sound output
level at each speaker.
(For details, refer to
page 20 and 21.)
PLAY
TEST
CD
TUNER
DIR B
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
Selects a digital sound
field program.
VCR 1
SUR.
ROCK
REAR
LEVEL
PLAY
A/B/C/D/E
HALL
DELAY TIME
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
VOLUME
Switches on/off the
digital sound field
processor (DSP).
Adjusts the delay time.
(For details, refer to
page 21.)
18
English
Description of Each Sound Field Program
The following list gives brief descriptions of the sound fields produced by each of the DSP programs. Keep in mind that most of
these are precise digital recreations of actual acoustic environments. The data for them was recorded at the locations described
using sophisticated sound field measurement equipment.
Note
The channel level balance between the left rear effect speaker and the right rear effect speaker may vary depending on the
sound field you are listening to. This is due to the fact that most of these sound field recreations are actual acoustic
environments.
PROGRAM
PRO LOGIC
PRO LOGIC
ENHANCED
FEATURE
This program is effective for playback of sources encoded with Dolby Surround.
The employment of the digital signal processing system improves crosstalk and transfers the sound source
more smoothly and precisely, compared to the conventional type. A stable movie sound field is recreated.
This program is effective for playback of sources encoded with Dolby Surround.
Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker
systems of a 35 mm film theater, thus widening the surrounded-sound field with greater presence.
CONCERT VIDEO
This program is effective for music videos and gives excellent depth and clarity for vocals. For opera, the
orchestra and stage are ideally recreated, letting you feel as if you were in an actual concert hall.
MONO MOVIE
This program is designed specifically to enhance mono source programs. Compared to a strictly mono
setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an
immediacy to the overall sound. It is particularly effective when used with old mono movies, news
broadcasts and dialog.
STADIUM
DISCO
This program gives you long delays between direct sounds and effect sounds, and extraordinarily
spacious feel of a large stadium.
This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The
sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound.
ROCK CONCERT
This program is suitable for rock music. A big, powerful sound is reproduced lively and dynamically.
CONCERT HALL
In this program, the center seems deep behind the front speaker pair, creating an expansive, large hall
ambience.
Description of Dolby Pro Logic Surround
DOLBY PRO LOGIC SURROUND: This unit employs
the Dolby Pro Logic Surround system. This system is similar to
professional Dolby Stereo decoders used in movie theaters.
By employing a four-channel system, the Dolby Pro Logic
Surround system divides the input signals into four levels: the
left and right main channels, the center channel (to
characterize dialog), and the rear surround-sound channels (to
characterize sound effects, background noise and other
ambient noise).
Dolby Surround is encoded on the sound track of commercially
available video cassettes and video discs as well. When you
play a source encoded with Dolby Surround on your home
video system, the Dolby Pro Logic Surround system in this unit
decodes the signal and feeds the surround-sound effects.
The Dolby Pro Logic Surround mode may not be always
effective on video sources not encoded with Dolby Surround.
Manufactured under license from Dolby Laboratories Licensing
Corporation. Additionally licensed under Canadian patent
number 1,037,877. “Dolby”, “Pro Logic”, and the double-D
symbol are trademarks of Dolby Laboratories Licensing
Corporation.
19
To play a source with the digital sound field processor
REC PAUSE
DIR A
TEST
PRO LOGIC
CENTER
LEVEL
1
2
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
MONO MOVIE STADIUM
HALL
DELAY TIME
3
2
DIR B
VCR 1
SUR.
ROCK
REAR
LEVEL
PLAY
STOP
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
2
VOLUME
3
3
Follow steps 1 – 6 shown in “BASIC OPERATIONS” on
page 15.
If desired, adjust the delay time and the output level of
each speaker. (For details, refer to the corresponding
descriptions on this page and the next page.)
Select the desired program that is suitable for the
source.
EFFECT
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
DISCO
ROCK
CONCERT
CONCERT
HALL
Notes
● If you prefer to cancel the DSP, press the EFFECT switch.
The sound will be the normal 2-channel stereo without
surround sound effect.
●
When CONCERT VIDEO, MONO MOVIE, STADIUM,
DISCO, ROCK CONCERT or CONCERT HALL is
selected, no sound is heard from the center speaker.
●
When a monaural sound source is played with DOLBY
PRO LOGIC or DOLBY PRO LOGIC ENHANCED, no
sound is heard from the front speakers and the rear
speakers. Sound is heard only from the center speaker.
However, if the center channel mode is in PHANTOM, the
front speakers output the sound of the center channel.
●
When this unit’s Dolby Pro Logic Surround system is used,
if the main-source sound is considerably altered by
overadjustment of the BASS or TREBLE controls, the
relationship between the center and rear channels may
produce an unnatural effect.
PRO LOGIC
The selected program name is shown on the display.
* The following adjustments can be done on the remote control transmitter as well as on the front panel.
Adjustment of the CENTER LEVEL
If desired, you can adjust the sound output level of the center
speaker even if the output level is already set in “SPEAKER
BALANCE ADJUSTMENT” on page 14.
By continuously pressing “+” or “–” on the CENTER LEVEL
control, the level value changes continuously. However, the
value stops changing momentarily at the preset point (80).
●
If the digital sound field program CONCERT VIDEO, MONO
MOVIE, STADIUM, DISCO, ROCK CONCERT or
CONCERT HALL is selected, the CENTER LEVEL control
cannot function.
●
Once the output level is adjusted, the level value will be the
same in the DOLBY PRO LOGIC and DOLBY PRO LOGIC
ENHANCED programs.
●
If a digital sound field program is not used, the CENTER
LEVEL control will not function.
Lights up.
CENTER LEVEL
CENTER
Adjustable
20
English
Adjustment of the REAR LEVEL
If desired, you can adjust the sound output level of the rear
speakers even if the output level is already set in “SPEAKER
BALANCE ADJUSTMENT” on page 14.
Lights up.
By continuously pressing “+” or “–” on the REAR LEVEL
control, the level value changes continuously. However, the
value stops changing momentarily at the preset point (80).
●
Once the output level is adjusted, the level value will be the
same in all the digital sound field programs.
●
If DOLBY PRO LOGIC or a digital sound field program is
not used, the REAR LEVEL control will not function.
REAR LEVEL
REAR
Adjustable
Adjustment of DELAY TIME
You can adjust the time difference between the beginning of
the source sound and the beginning of the effect sound with
the DELAY TIME control.
The DELAY TIME control is effective with all programs.
By applying more or less delay, sound effects, background
noise, and ambient noise coming at you from the rear speakers
can be enhanced or subdued for extra effect.
1.
PRO LOGIC
: from 15 to 30 milliseconds
(Preset value: 20 milliseconds)
2.
PRO LOGIC : from 15 to 30 milliseconds
ENHANCED
(Preset value: 20 milliseconds)
3. CONCERT VIDEO : from 1 to 100 milliseconds
(Preset value: 28 milliseconds)
4. MONO MOVIE
: from 1 to 100 milliseconds
(Preset value: 20 milliseconds)
5. STADIUM
: from 1 to 50 milliseconds
(Preset value: 45 milliseconds)
6. DISCO
: from 1 to 100 milliseconds
(Preset value: 14 milliseconds)
7. ROCK CONCERT : from 1 to 100 milliseconds
(Preset value: 17 milliseconds)
8. CONCERT HALL : from 1 to 100 milliseconds
(Preset value: 30 milliseconds)
By continuously pressing “+” or “–” on the DELAY TIME
control, the value changes continuously.
However, the value stops changing momentarily at the preset
point.
Adjustable
DELAY TIME
STEREO
DELAY
0
20
l00
ms
ONCERT
VIDEO
Note
Adding too much delay will cause an unnatural effect with
some sources. Experiment with the DELAY TIME control to
create the effect that you find most suitable.
Note
The values of the DELAY TIME, CENTER LEVEL and REAR
LEVEL you set the last time will remain memorized even when
the power of this unit is off.
However, if the power cord is kept disconnected for more than
one week, these values will be automatically changed back to
the original factory settings.
21
SETTING THE SLEEP TIMER
If you use the SLEEP timer of this unit, you can make this unit turn off automatically. When you are going to sleep while enjoying a
broadcast or other desired input source, this timer function is helpful.
Notes
● The SLEEP timer can be controlled only with the remote control transmitter.
● The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear
panel of this unit.
To set the SLEEP time
To cancel the selected SLEEP time
1
SLEEP
SLEEP
Press once or more to
select the desired
SLEEP time.
Press once or more so that the display returns to the indication
before the SLEEP timer is set. (“SLEEP” will go off from the
display.)
Indicates the SLEEP time.
Note
The SLEEP timer setting can also be canceled by turning off
the power with the POWER switch or disconnecting the power
plug of this unit from the AC outlet.
SLEEP
ms
l00
T
Flashes on and off continuously.
Whenever the SLEEP key is pressed, the SLEEP time will
change as follows.
(Minutes)
120
90
60
30
The SLEEP timer is OFF.
(The indication before the SLEEP
key is pressed.)
After a while, the display returns to the indication before
the SLEEP timer is set, and the “SLEEP” indicator stops
flashing and lights up.
2
22
The unit will be turned off automatically at the selected
SLEEP time.
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the
CD player, tuner and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also control
various functions of each component.
English
REMOTE CONTROL TRANSMITTER
KEY FUNCTIONS
For Control of This Unit
* Refer to “SETTING THE SLEEP
TIMER” on the previous page.
POWER
SLEEP
PHONO
DISC
SKIP
Turns the power on/off.
SKIP
PAUSE/STOP
DECK A/B
REC PAUSE
PRESET
DIR A
TEST
CD
A/B/C/D/E
TUNER
DIR B
TAPE MON
STOP
PRO LOGIC
CENTER
LEVEL
PLAY
PLAY
LD/TV
ENHANCED CNCT VIDEO
Selects input source.
VCR 1
SUR.
MONO MOVIE STADIUM
ROCK
REAR
LEVEL
HALL
DELAY TIME
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
VOLUME
Turns the master volume level up/down.
* For the DSP control keys, refer to the page 18.
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the
same. On each key function, refer to the corresponding instruction on your component’s manual.
Controls the compact disc player.
* DISC SKIP is applicable only
to a compact disc changer.
POWER
SLEEP
PHONO
DISC
SKIP
SKIP
DECK A/B
Controls the tape deck.
* DIR A, B and DECK A/B are
applicable only to a double
cassette tape deck.
* For a single cassette deck with
automatic reverse function,
pressing DIR A will reverse
the direction of tape running.
REC PAUSE
PAUSE/STOP
PRESET
DIR A
PLAY
TEST
STOP
CENTER
LEVEL
MONO MOVIE STADIUM
PRO LOGIC
CD
TUNER
DIR B
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
VCR 1
SUR.
ROCK
REAR
LEVEL
PLAY
A/B/C/D/E
HALL
DELAY TIME
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
Controls the tuner.
* +: Selects higher preset
station number.
–: Selects lower preset station
number.
A/B/C/D/E: Selects the page
(A – E) of preset
stations.
VOLUME
23
STANDBY mode (U.K. and Europe models only)
While the power is on, pressing the POWER key on the remote
control transmitter switches the unit to the STANDBY mode. (In
this mode, the indicator is half illuminated.)
POWER on mode
STANDBY mode
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Remote control transmitter operation range
1
3
Remote control
sensor
2
Within approximately
6 m (19.7 feet)
30°
30°
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
● Use only AA, R6, UM-3 batteries for replacement.
● Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
● Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
● If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
24
Notes
● There should be no large obstacles between the remote
control transmitter and the main unit.
● If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
CAUSE
REMEDY
The unit fails to turn on when the
POWER switch is pressed.
Power cord is not plugged in or is not
completely inserted.
Firmly plug in the power cord.
No sound or no picture.
Incorrect output cord connections.
Connect the cords properly. If the
problem persists, the cords may be
defective.
Appropriate input selector is not pressed.
Press the appropriate input selector
corresponding to the input source.
The protection circuit has been activated
because of short circuit etc.
Turning the unit off and then on will
reset the protection circuit.
The SLEEP timer functioned.
Do not make the SLEEP timer function.
Only one side speaker outputs the
sound.
Incorrect setting of the BALANCE control.
Adjust it to the appropriate position.
Incorrect cord connections.
Connect the cords properly. If the
problem persists, the cords may be
defective.
Sound “hums”.
Incorrect cord connections.
Firmly connect the audio plugs. If the
problem persists, the cords may be
defective.
No connection from the turntable to the
GND terminal.
Make the GND connection between the
turntable and this unit.
The volume level is low while playing a
record.
The record is being played on a turntable
with an MC cartridge.
The player should be connected to the
unit through the MC head amplifier.
The volume level cannot be increased,
or sound is distorted.
The power to the component connected
to the REC OUT terminals of this unit is
off.
Turn the power to the component on.
No sound from the rear speakers.
The sound output level to the rear
speakers is set to 0.
Turn up the sound output level with the
REAR LEVEL control.
The monaural sound source is played in
DOLBY PRO LOGIC or DOLBY PRO
LOGIC ENHANCED mode.
Select another program suitable for the
monaural sound source.
The sound output level to the center
speaker is set to 0.
Turn up the sound output level with the
CENTER LEVEL control.
The center channel mode is in
PHANTOM mode.
Select NORMAL or WIDE.
The sound suddenly goes off.
No sound from the center speaker.
English
TROUBLESHOOTING
Incorrect sound field program selection.
Select the appropriate program.
No sound field program is selected.
The remote control transmitter does
not work.
The sound is degraded when
monitoring is performed by using the
headphones connected to the compact
disc player or cassette deck which are
connected with this unit.
Direct sunlight or lighting (of an inverter
type of flourescent lamp etc.) is striking
the remote control sensor of the main
unit.
Change the position of the main unit.
The batteries of this remote control
transmitter are too weak.
Replace the batteries with new ones.
The power to this unit is off.
Turn the power to this unit on.
25
SPECIFICATIONS
AUDIO SECTION
Minimum RMS Output Power per Channel
Front L, R
8 ohms, 20 Hz to 20 kHz, 0.04% THD ....................70W+70W
Center
8 ohms, 20 Hz to 20 kHz, 0.07% THD .............................70W
Rear L, R
8 ohms, 1 kHz, 0.3% THD .....................................20W+20W
Maximum Output Power
[General model only]
8 ohms, 1 kHz, 10% THD (FRONT L/R)............105W+105W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring method)
8/6/4/2 ohms ..............................................95/120/150/170W
DIN Standard Output Power per Channel
4 ohms, 1 kHz, 0.7% THD
[Europe model only] ....................................................100W
IEC Power
8 ohms, 1 kHz, 0.1% THD
[Europe model only] ......................................................78W
Power Band Width
8 ohms, 30W, 0.08% THD ............................10 Hz to 50 kHz
Damping Factor (SPEAKERS A)
8 ohms, 20 Hz to 20 kHz.......................................80 or more
Input Sensitivity/Impedance
PHONO MM ..............................................2.5 mV/47 k-ohms
CD/TAPE/TUNER/LD·TV/VCR..................150 mV/47 k-ohms
Maximum Input Signal (1 kHz, 0.5% THD)
PHONO MM ...............................................................115 mV
CD/TAPE/TUNER/LD·TV/VCR (EFFECT ON) .................2.2V
Output Level/Impedance
REC OUT ................................................150 mV/1.0 k-ohms
PRE OUT......................................................2.2V/1.2 k-ohms
LPF (EFFECT OFF) ......................................3.5V/1.5 k-ohms
Headphone Jack Rated Output/Impedance
Output Level (8 ohms, 1 kHz, 150 mV ) ..........................0.5V
Impedance............................................................390 ohms
Frequency Response (20 Hz to 20 kHz)
CD/TAPE/TUNER/LD·TV/VCR (FRONT L/R)............0±0.5 dB
RIAA Equalization Deviation
PHONO MM .............................................................0±0.5 dB
Total Harmonic Distortion
PHONO MM to REC OUT
20 Hz to 20 kHz, 1V........................................0.02% or less
CD/TAPE/TUNER/LD·TV/VCR to SP OUT
FRONT L/R (EFFECT OFF)
20 Hz to 20 kHz, 30W/8 ohms .....................0.02% or less
REAR L/R
1 kHz, 10W/8 ohms ........................................0.3% or less
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM to REC OUT (5 mV Input Shorted)
[U.K. and Europe models] ..........................................82 dB
[Australia and General models]..................................85 dB
CD/TAPE/TUNER/LD·TV/VCR to SP OUT (Input Shorted,
EFFECT OFF) .................................................99 dB or more
26
Residual Noise (IHF-A Network)
FRONT L/R......................................................140 µV or less
Channel Separation
(Vol. –30 dB, EFFECT OFF)
PHONO MM
(Input Shorted 1 kHz/10 kHz)
...............................................60 dB or more/50 dB or more
CD/TAPE/TUNER/LD·TV/VCR
(Input 5.1 k-ohms Shorted 1 kHz/10 kHz)
...............................................60 dB or more/44 dB or more
Tone Control Characteristics
BASS:
Boost/cut .............................±10 dB (50 Hz)
Turnover Frequency ......................(350 Hz)
TREBLE:
Boost/cut ...........................±10 dB (20 kHz)
Turnover Frequency .....................(3.5 kHz)
Filter Characteristics
LPF (fc=200 Hz) ........................................................6 dB/oct
Gain Tracking Error (0 to –60 dB)..........................3 dB or less
VIDEO SECTION
Video Signal Level...........................................1 Vp-p/75 ohms
S-Video Signal Level
Y..................................................................1 Vp-p/75 ohms
C ..........................................................0.286 Vp-p/75 ohms
Maximum Input Level.....................................1.5 Vp-p or more
Signal-to-Noise Ratio .........................................50 dB or more
Monitor Out Frequency Response
...........................................................5 Hz to 10 MHz, –3 dB
GENERAL
Power Supply
[U.K. and Australia models] ........................AC 240V, 50 Hz
[Europe model] ...........................................AC 230V, 50 Hz
[General model] ................AC 110/120/220/240V, 50/60 Hz
Power Consumption ........................................................300W
AC Outlets
2 SWITCHED OUTLETS
[Europe and General models] ....................120W max. total
1 SWITCHED OUTLET
[U.K. and Australia models]........................120W max. total
Dimensions (W x H x D) ...........................435 x 146 x 386 mm
...................................................(17-1/8” x 5-3/4” x 15-3/16”)
Weight .......................................................10 kg (22 lbs. 0 oz.)
Accessories ....................................Remote control transmitter
Batteries
Specifications are subject to change without notice.
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VS73740
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising