Daikin | FVXS25GV1A | FVXS25-50GV1A operation manual - 3P232453-1_0

FVXS25-50GV1A operation manual - 3P232453-1_0
00_CV_3P232453-1.fm Page 1 Wednesday, June 4, 2008 3:09 PM
DAIKIN ROOM AIR CONDITIONER
Operation Manual
MODELS
FVXS25GV1A
FVXS35GV1A
FVXS50GV1A
01_EN_3P232453-1.fm Page 1 Wednesday, June 4, 2008 9:18 AM
CONTENTS
READ BEFORE OPERATION
Safety precautions ......................................... 2
Names of parts............................................... 4
Preparation Before Operation ........................ 7
OPERATION
AUTO · DRY · COOL · HEAT · FAN
Operation ..................................................... 10
Adjusting the Airflow Direction ..................... 12
POWERFUL Operation ................................ 14
OUTDOOR UNIT QUIET Operation............. 15
ECONO Operation ....................................... 16
TIMER Operation ......................................... 17
WEEKLY TIMER Operation ......................... 19
Note for Multi System................................... 24
CARE
Care and Cleaning ....................................... 26
TROUBLE SHOOTING
Trouble Shooting.......................................... 29
1
01_EN_3P232453-1.fm Page 2 Wednesday, June 4, 2008 9:18 AM
READ BEFORE OPERATION
Safety precautions
•
•
•
•
Keep this manual where the operator can easily find them.
Read this manual attentively before starting up the unit.
For safety reason the operator must read the following cautions carefully.
This manual classifies precautions into WARNING and CAUTION. Be sure to follow all precautions
below: they are all important for ensuring safety.
WARNING
CAUTION
If you do not follow these instructions exactly, the unit may If you do not follow these instructions exactly, the unit may
cause property damage, personal injury or loss of life.
cause minor or moderate property damage or personal injury.
Never do.
Be sure to follow the instructions.
Be sure to earth the air conditioner.
Never cause the air conditioner (including the
remote controller) to get wet.
Never touch the air conditioner (including the
remote controller) with a wet hand.
WARNING
• In order to avoid fire, explosion or injury, do not operate the unit when harmful, among
which flammable or corrosive gases, are detected near the unit.
• It is not good for health to expose your body to the air flow for a long time.
• Do not put a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at
a high speed, it will cause injury.
• Do not attempt to repair, relocate, modify or reinstall the air conditioner by yourself. Incorrect work
will cause electric shocks, fire etc.
For repairs and reinstallation, consult your Daikin dealer for advice and information.
• The refrigerant used in the air conditioner is safe. Although leaks should not occur, if for
some reason any refrigerant happens to leak into the room, make sure it does not come in
contact with any flame as of gas heaters, kerosene heaters or gas range.
• If the air conditioner is not cooling (heating) properly, the refrigerant may be leaking, so call your dealer.
When carrying out repairs accompanying adding refrigerant, check the content of the repairs with our service staff.
• Do not attempt to install the air conditioner by your self. Incorrect work will result in water leakage,
electric shocks or fire. For installation, consult the dealer or a qualified technician.
• In order to avoid electric shock, fire or injury, if you detect any abnormally such as smell of fire, stop
the operation and turn off the breaker. And call your dealer for instructions.
• Depending on the environment, an earth leakage breaker must be installed. Lack of an earth leakage breaker may result in electric shocks or fire.
• The air conditioner must be earthed. Incomplete earthing may result in electric shocks. Do
not connect the earth line to a gas pipe, water pipe, lightning rod, or a telephone earth line.
CAUTION
• In order to avoid any quality deterioration, do not use the unit for cooling precision instruments, food, plants, animals or works of art.
• Never expose little children, plants or animals directly to the air flow.
2
01_EN_3P232453-1.fm Page 3 Wednesday, June 4, 2008 9:18 AM
• Do not place appliances which produce open fire in places exposed to the air flow from the unit or
under the indoor unit. It may cause incomplete combustion or deformation of the unit due to the heat.
• Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.
• Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not remove the fan guard.
• Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In certain conditions, moisture in the air may condense and drip.
• After a long use, check the unit stand and fittings for damage.
• Do not touch the air inlet and alminum fins of outdoor unit. It may cause injury.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.
• To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is used
together with the air conditioner.
• Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply cord.
• Do not connect the air conditioner to a power supply different from the one as specified. It
may cause trouble or fire.
• Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the
building, furniture etc.
• Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris
accumulate around the unit.
Leaves are a hotbed for small animals which can enter the unit. Once in the unit, such animals can
cause malfunctions, smoke or fire when making contact with electrical parts.
• Do not operate the air conditioner with wet hands.
• Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
• Do not place things such as vessels containing water or anything else on top of the unit. Water
may penetrate into the unit and degrade electrical insulations, resulting in an electric shock.
Installation site.
■ To install the air conditioner in the following types of environments, consult the dealer.
• Places with an oily ambient or where steam or soot occurs.
• Salty environment such as coastal areas.
• Places where sulfide gas occurs such as hot springs.
• Places where snow may block the outdoor unit.
• The indoor unit is at least 1 meter away from any television or radio set (unit may cause interference with the picture or sound).
The drain from the outdoor unit must be discharged to a place of good drainage.
Consider nuisance to your neighbours from noises.
■ For installation, choose a place as described below.
• A place solid enough to bear the weight of the unit which does not amplify the operation noise or vibration.
• A place from where the air discharged from the outdoor unit or the operation noise will not annoy
your neighbours.
Electrical work.
• For power supply, be sure to use a separate power circuit dedicated to the air conditioner.
System relocation.
• Relocating the air conditioner requires specialized knowledge and skills. Please consult the
dealer if relocation is necessary for moving or remodeling.
3
01_EN_3P232453-1.fm Page 4 Wednesday, June 4, 2008 9:18 AM
Names of parts
■ Indoor Unit
1
2
8
3
7
12
10
4
2
9
5
11
6
■ Opening the Front Panel
How to open the front panel: (page 26.)
Air outlet selection switch
•
This setting blows air from upper outlet only.
•
This setting automatically decides a blow
pattern depending on mode and conditions.
• This setting is
recommended.
13
• The unit is shipped from the
factory with this setting.
14
CAUTION
Before opening the front panel, be sure to stop the operation and turn the breaker OFF.
Do not touch the metal parts on the inside of the indoor unit, as it may result in injury.
4
01_EN_3P232453-1.fm Page 5 Wednesday, June 4, 2008 9:18 AM
■ Outdoor Unit
15
16
17
19
18
■ Indoor Unit
1. Titanium Apatite Photocatalytic
Air-Purifying Filter:
• These filters are attached to the inside of
the air filters.
2. Air outlet
3. Display
4. Front panel
5. Vertical blades (louvers): (page 12.)
• The louvers are inside of the air outlet.
6. Air inlet
7. Air filter
8. Horizontal blade (flap): (page 12.)
9. Operation lamp (green)
10. TIMER lamp (yellow): (page 17.)
11. Indoor Unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
• The operation mode refers to the following
table.
Temperature
setting
22°C
COOL
AUTO
25°C
Mode
Airflow rate
AUTO
AUTO
• This switch is useful when the remote
controller is missing.
12. Signal receiver:
• It receives signals from the remote
controller.
• When the unit receives a signal, you will
hear a short beep.
• Operation start ........ beep-beep
• Settings changed ..... beep
• Operation stop.......... beeeeep
13. Air outlet selection switch: (page 13.)
14. Room temperature sensor:
• It senses the air temperature around the unit.
■ Outdoor Unit
15. Air inlet: (Back and side)
16. Refrigerant piping and inter-unit cable
18. Earth terminal:
• It is inside of this cover.
17. Drain hose
19. Air outlet
Appearance of the outdoor unit may differ from some models.
5
01_EN_3P232453-1.fm Page 6 Wednesday, June 4, 2008 9:18 AM
■ Remote Controller
1
2
5
3
<Open the lid>
6
4
7
8
11
12
13
15
9
10
14
16
<ARC452A2>
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. FAN setting button:
• It selects the airflow rate setting.
4. POWERFUL button:
POWERFUL operation (page 14.)
5. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
6. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN) (page 10.)
8. QUIET button:
OUTDOOR UNIT QUIET operation (page 15.)
6
9. ECONO button:
ECONO operation (page 16.)
10. SWING button:
• Adjusting the Airflow Direction (page 12.)
11. WEEKLY/PROGRAM/COPY/BACK/NEXT
button:
• WEEKLY TIMER operation (page 19.)
12. SELECT button:
• It changes the ON/OFF TIMER and
WEEKLY TIMER settings. (page 17, 19.)
13. OFF TIMER button: (page 17.)
14. ON TIMER button: (page 18.)
15. TIMER CANCEL button:
• It cancels the timer setting. (page 17, 18.)
• It cannot be used for the WEEKLY TIMER operation.
16. CLOCK button: (page 8.)
01_EN_3P232453-1.fm Page 7 Wednesday, June 4, 2008 9:18 AM
Preparation Before Operation
■ To set the batteries
2
1. Slide the front cover to take it off.
Position + and
– correctly!
2. Set two dry batteries (LR03·AAA).
3. Set the front cover as before.
3
1
■ To operate the remote controller
• To use the remote controller, aim the transmitter at the indoor
unit. If there is anything to block signals between the unit and
the remote controller, such as a curtain, the unit will not
operate.
• Do not drop the remote controller. Do not get it wet.
• The maximum distance for communication is about 7m.
Receiver
■ To fix the remote controller holder
on the wall
Remote
controller
holder
1. Choose a place from where the signals
reach the unit.
2. Fix the holder to a wall, a pillar, etc. with the
screws supplied with the holder.
3. Place the remote controller in the remote
controller holder.
Set.
• To remove, pull it
upwards.
ATTENTION
■ About batteries
• When replacing the batteries, use batteries of the same type, and replace the two old batteries together.
• When the system is not used for a long time, take the batteries out.
• We recommend replacing once a year, although if the remote controller display begins to fade or if reception
deteriorates, please replace with new alkaline batteries. Using manganese batteries reduces the lifespan.
• The attached batteries are provided for the initial use of the system.
The usable period of the batteries may be short depending on the manufactured date of the air conditioner.
■ About remote controller
• Never expose the remote controller to direct sunlight.
• Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.
• Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such
as inverter-type lamps) is in the room. Consult the shop if that is the case.
• If the remote controller signals happen to operate another appliance, move that appliance
to somewhere else, or consult the shop.
7
01_EN_3P232453-1.fm Page 8 Wednesday, June 4, 2008 9:18 AM
Preparation Before Operation
■ To set the clock
1. Press “CLOCK button”.
is displayed.
and
blinks.
2. Press “SELECT button” to set
the current day of the week.
3. Press “CLOCK button”.
blinks.
4. Press “SELECT button” to set
the clock to the present time.
Holding down “
” or “
” button
rapidly increases or decreases the time
display.
5. Press “CLOCK button”.
Always point the remote controller at the
indoor unit when pushing the buttons
when setting the indoor unit’s internal
clock.
blinks.
2, 4
1, 3, 5
NOTE
• If the indoor unit’s internal clock is not set to the correct time, the WEEKLY TIMER will not
operate punctually.
8
01_EN_3P232453-1.fm Page 9 Wednesday, June 4, 2008 9:18 AM
■ Turn the breaker ON
• Turning ON the breaker closes the flap. (This is a normal procedure.)
NOTE
■ Tips for saving energy
• Be careful not to cool (heat) the room too much.
Keeping the temperature setting at a moderate level helps save energy.
• Cover windows with a blind or a curtain.
Blocking sunlight and air from outdoors increases the cooling (heating) effect.
• Clogged air filters cause inefficient operation and waste energy.
Clean them once in about every two weeks.
Recommended temperature setting
For cooling:26°C – 28°C
For heating:20°C – 24°C
■ Please note
• The air conditioner always consumes 15-35 watts of electricity even while it is not operating.
• If you are not going to use the air conditioner for a long period, for example in spring or autumn, turn the breaker OFF.
• Use the air conditioner in the following conditions.
Mode
Operating conditions
If operation is continued out of this range
COOL
Outdoor temperature: 〈3MXS〉 –5 to 46°C
〈4MXS〉 –10 to 46°C
〈3/4MKS〉 10 to 46°C
〈RXS〉 10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
• A safety device may work to stop the operation.
(In multi system, it may work to stop the operation of
the outdoor unit only.)
• Condensation may occur on the indoor unit and drip.
HEAT
Outdoor temperature: 〈3/4MXS〉 –15 to 24°C
〈RXS25/35〉 –10 to 24°C
〈RXS50〉 –15 to 24°C
Indoor temperature: 10 to 30°C
• A safety device may work to stop the operation.
DRY
Outdoor temperature: 〈3MXS〉 –5 to 46°C
〈4MXS〉 –10 to 46°C
〈3/4MKS〉 10 to 46°C
〈RXS〉 10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
• A safety device may work to stop the operation.
• Condensation may occur on the indoor unit and drip.
• Operation outside this humidity or temperature range may cause a safety device to disable the system.
9
01_EN_3P232453-1.fm Page 10 Wednesday, June 4, 2008 9:18 AM
OPERATION
AUTO · DRY · COOL · HEAT · FAN Operation
The air conditioner operates with the operation
mode of your choice.
From the next time on, the air conditioner will
operate with the same operation mode.
■ To start operation
1. Press “MODE selector button”
and select a operation mode.
• Each pressing of the button advances
the mode setting in sequence.
: AUTO
: DRY
4
: COOL
: HEAT
: FAN
2, 3
1
2. Press “ON/OFF button”.
• The OPERATION lamp lights up.
■ To stop operation
3. Press “ON/OFF button” again.
• Then OPERATION lamp goes off.
■ To change the temperature setting
4. Press “TEMPERATURE adjustment button”.
DRY or FAN mode
AUTO or COOL or HEAT mode
Press “
“
The temperature setting is not variable.
10
” to raise the temperature and press
” to lower the temperature.
Set to the temperature you like.
01_EN_3P232453-1.fm Page 11 Wednesday, June 4, 2008 9:18 AM
■ To change the airflow rate setting
5. Press “FAN setting button”.
DRY mode
AUTO or COOL or HEAT or FAN mode
Five levels of airflow rate setting from “
The airflow rate setting is not variable.
plus “
”“
” to “
”
” are available.
• Indoor unit quiet operation
When the airflow is set to “ ”, the noise from the indoor unit will become quieter.
Use this when making the noise quieter.
The unit might lose capacity when the airflow rate is set to a weak level.
NOTE
■ Note on HEAT operation
• Since this air conditioner heats the room by taking heat from outdoor air to indoors, the
heating capacity becomes smaller in lower outdoor temperatures. If the heating effect is
insufficient, it is recommended to use another heating appliance in combination with the air
conditioner.
• The heat pump system heats the room by circulating hot air around all parts of the room.
After the start of heating operation, it takes some time before the room gets warmer.
• In heating operation, frost may occur on the outdoor unit and lower the heating capacity. In
that case, the system switches into defrosting operation to take away the frost.
• During defrosting operation, hot air does not flow out of indoor unit.
■ Note on COOL operation
• This air conditioner cools the room by blowing the hot air in the room outside, so if the
outside temperature is high, the performance of the air conditioner drops.
■ Note on DRY operation
• The computer chip works to rid the room of humidity while maintaining the temperature as
much as possible. It automatically controls temperature and airflow late, so manual
adjustment of these functions is unavailable.
■ Note on AUTO operation
• In AUTO operation, the system selects a temperature setting and an appropriate operation
mode (COOL or HEAT) based on the room temperature at the start of the operation.
• The system automatically reselects setting at a regular interval to bring the room
temperature to user-setting level.
• If you do not like AUTO operation, manually change the set temperature.
■ Note on airflow rate setting
• At smaller airflow rates, the cooling (heating) effect is also smaller.
11
01_EN_3P232453-1.fm Page 12 Wednesday, June 4, 2008 9:18 AM
Adjusting the Airflow Direction
You can adjust the airflow direction to increase
your comfort.
■ To adjust the horizontal
blade (flap)
1. Press “SWING button”.
• “
” is displayed on the LCD and the
flaps will begin to swing.
2. When the flap has reached the
desired position, press
“SWING button” once more.
• The flap will stop moving.
• “
” disappears from the LCD.
1, 2
■ To adjust the vertical
blades (louvers)
Hold the knob and move the louver.
(You will find a knob on the left-side and the rightside blades.)
Notes on flap and louvers angle
• Unless “SWING” is selected, you should set the
flap at a near-horizontal angle in HEAT mode and
at a upward position in COOL or DRY mode to
obtain the best performance.
■ ATTENTION
• When adjusting the flap by hand, turn off the unit,
and use the remote controller to restart the unit.
• Be careful when adjusting the louvers. Inside the
air outlet, a fan is rotating at a high speed.
12
HEAT
COOL/
DRY
01_EN_3P232453-1.fm Page 13 Wednesday, June 4, 2008 9:18 AM
■ Airflow selection
• Make airflow selection according to what suits you.
When setting the airflow selection switch to
.
• Air conditioner automatically decides the appropriate blowing pattern depending on the operating
mode/situation.
Operating mode
Situation
Blowing pattern
COOL mode
• When the room has become fully
cool, or when one hour has
passed since turning on the air
conditioner.
• So that air does not come into
direct contact with people, air is
blown upper air outlet, room temperature is equalized.
• At start of operation or other
times when the room is not fully
cooled.
• At times other than below.
(Normal time.)
• Air is blown from the upper and
lower air outlets for high speed
cooling during COOL mode, and
for filling the room with warm air
during HEAT mode.
HEAT mode
• At start or when air temperature
is low.
• So that air does not come into
direct contact with people. Air is
blown upper air outlet.
• During Dry mode, so that cold air does not come into direct contact with people, air is blown
upper air outlet.
When setting the air outlet selection switch to
.
• Regardless of the operating mode or situation, air blows from the upper air outlet.
• Use this switch when you do not want air coming out of the lower air outlet. (While sleeping etc.)
CAUTION
• Do not try to adjust the flap by hand.
• When adjusting by hand, the mechanism may not operate properly or condensation may drip
from air outlets.
13
01_EN_3P232453-1.fm Page 14 Wednesday, June 4, 2008 9:18 AM
POWERFUL Operation
POWERFUL operation quickly maximizes the
cooling (heating) effect in any operation mode.
You can get the maximum capacity.
■ To start POWERFUL
operation
1. Press “POWERFUL button”.
• POWERFUL operation ends in
20minutes. Then the system
automatically operates again with the
previous settings which were used
before POWERFUL operation.
• “
” is displayed on the LCD.
• When using POWERFUL operation,
there are some functions which are
not available.
1, 2
■ To cancel POWERFUL
operation
2. Press “POWERFUL button”
again.
• “
” disappears from the LCD.
NOTE
■ Notes on POWERFUL operation
• POWERFUL Operation cannot be used together with ECONO or QUIET Operation.
Priority is given to the function of whichever button is pressed last.
• POWERFUL Operation can only be set when the unit is running. Pressing the operation
stop button causes the settings to be canceled, and the “ ” disappears from the LCD.
• In COOL and HEAT mode
To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased
and the airflow rate be fixed to the maximum setting.
The temperature and airflow settings are not variable.
• In DRY mode
The temperature setting is lowered by 2.5°C and the airflow rate is slightly increased.
• In FAN mode
The airflow rate is fixed to the maximum setting.
• When using priority-room setting
See “Note for Multi System”. (page 24.)
14
01_EN_3P232453-1.fm Page 15 Wednesday, June 4, 2008 9:18 AM
OUTDOOR UNIT QUIET Operation
OUTDOOR UNIT QUIET operation lowers the
noise level of the outdoor unit by changing the
frequency and fan speed on the outdoor unit.
This function is convenient during night.
■ To start OUTDOOR
UNIT QUIET operation
1. Press “QUIET button”.
• “
” is displayed on the LCD.
■ To cancel OUTDOOR
UNIT QUIET operation
2. Press “QUIET button” again.
• “
” disappears from the LCD.
1, 2
NOTE
■ Note on OUTDOOR UNIT QUIET operation
• If using a multi system, this function will work only when the OUTDOOR UNIT QUIET
operation is set on all operated indoor units.
However, if using priority-room setting, see “Note for Multi System”. (page 24.)
• This function is available in COOL, HEAT, and AUTO modes.
(This is not available in FAN and DRY mode.)
• POWERFUL operation and OUTDOOR UNIT QUIET operation cannot be used at the
same time.
Priority is given to the function of whichever button is pressed last.
• If operation is stopped using the remote controller or the main unit ON/OFF switch when
using OUTDOOR UNIT QUIET operation, “
” will remain on the remote controller
display.
15
01_EN_3P232453-1.fm Page 16 Wednesday, June 4, 2008 9:18 AM
ECONO Operation
ECONO operation is a function which enables
efficient operation by limiting the maximum power
consumption value.
This function is useful for cases in which attention
should be paid to ensure a circuit breaker will not
trip when the product runs alongside other
appliances.
■ To start ECONO
operation
1. Press “ECONO button”.
•“
” is displayed on the LCD.
■ To cancel ECONO
operation
2. Press “ECONO button” again.
•“
1, 2
” disappears from the LCD.
Running current and
power consumption
Normal
operation
Maximum during
normal operation
Maximum during
ECONO Mode
ECONO
Mode
Time
From start up until set
temperature is reached
• This diagram is a representation for illustrative purposes only.
* The maximum running current and power consumption of the air conditioner in ECONO
mode vary with the connecting outdoor unit.
NOTE
• ECONO Operation can only be set when the unit is running. Pressing the operation stop
button causes the settings to be canceled, and the “ ” disappears from the LCD.
• ECONO operation is a function which enables efficient operation by limiting the power
consumption of the outdoor unit (operating frequency).
• ECONO operation functions in AUTO, COOL, DRY, and HEAT modes.
• POWERFUL and ECONO operation cannot be used at the same time.
Priority is given to the function of whichever button is pressed last.
• Power consumption may not drop even if ECONO operation is used of the level of power
consumption is already low.
16
01_EN_3P232453-1.fm Page 17 Wednesday, June 4, 2008 9:18 AM
TIMER Operation
Timer functions are useful for automatically
switching the air conditioner on or off at night or in
the morning. You can also use OFF TIMER and
ON TIMER in combination.
■ To use OFF TIMER
operation
• Check that the clock is correct.
If not, set the clock to the present time.
(page 8.)
1. Press “OFF TIMER button”.
is displayed.
blinks.
2. Press “SELECT button” until
the time setting reaches the
point you like.
• Every pressing of either button
increases or decreases the time
setting by 10 minutes. Holding down
either button changes the setting
rapidly.
3. Press “OFF TIMER button”
again.
1, 3
4
2
• The TIMER lamp lights up.
■ To cancel the OFF TIMER Operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
NOTE
• When TIMER is set, the present time is not displayed.
• Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is
canceled when remote controller batteries are replaced.)
• When operating the unit via the ON/OFF Timer, the actual length of operation may vary from
the time entered by the user. (Maximum approx. 10 minutes)
■ NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically adjusts the temperature
setting (0.5°C up in COOL, 2.0°C down in HEAT) to prevent excessive cooling (heating) for
your pleasant sleep.
17
01_EN_3P232453-1.fm Page 18 Wednesday, June 4, 2008 9:18 AM
TIMER Operation
■ To use ON TIMER
operation
• Check that the clock is correct. If not, set
the clock to the present time. (page 8.)
1. Press “ON TIMER button”.
is displayed.
blinks.
2. Press “SELECT button” until
the time setting reaches the
point you like.
• Every pressing of either button
increases or decreases the time setting
by 10 minutes. Holding down either
button changes the setting rapidly.
3. Press “ON TIMER button”
again.
• The TIMER lamp lights up.
2
1, 3
■ To cancel ON TIMER
operation
4
4. Press “CANCEL button”.
• The TIMER lamp goes off.
■ To combine ON TIMER and OFF TIMER
• A sample setting for combining the two timers is shown below.
Display
(Example)
Present time: 11:00 p.m.
(The unit operating)
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
Combined
ATTENTION
■ In the following cases, set the timer again.
• After a breaker has turned OFF.
• After a power failure.
• After replacing batteries in the remote controller.
18
01_EN_3P232453-1.fm Page 19 Wednesday, June 4, 2008 9:18 AM
WEEKLY TIMER Operation
Up to 4 timer settings can be saved for each day of the week. It is convenient if the WEEKLY TIMER is
set according to the family’s life style.
■ Using in these cases of WEEKLY TIMER
An example of WEEKLY TIMER settings is shown below.
Example: The same timer settings are made for the week from Monday through
Friday while different timer settings are made for the weekend.
[Monday] Make timer settings up to programs 1-4. (see page 20.)
Program 1
Program 2
Program 3
ON
OFF
ON
Program 4
OFF
25˚C
27˚C
6:00
8:30
17:30
OFF
25˚C
22:00
OFF
27˚C
ON
ON
25˚C
27˚C
[Tuesday] Use the copy mode to make settings for Tuesday to Friday, because these
to
settings are the same as those for Monday. (see page 22.)
Program 2
Program 3
Program 4
[Friday] Program 1
ON
OFF
ON
OFF
8:30
17:30
25˚C
27˚C
6:00
22:00
[Saturday] No timer settings
[Sunday] Make timer settings up to programs 1-4. (see page 20.)
Program 1
Program 2
Program 3
Program 4
ON
OFF
OFF
ON
19:00
21:00
25˚C
8:00
10:00
OFF
25˚C
ON
25˚C
27˚C
OFF
27˚C
27˚C
ON
27˚C
• Up to 4 reservations per day and 28 reservations per week can be set in the WEEKLY TIMER.
The effective use of the copy mode ensures ease of making reservations.
• The use of ON-ON-ON-ON settings, for example, makes it possible to schedule operating mode
and set temperature changes. Furthermore, by using OFF-OFF-OFF-OFF settings, only the turnOFF time of each day can be set. This will turn OFF the air conditioner automatically if the user
forgets to turn it OFF.
19
01_EN_3P232453-1.fm Page 20 Wednesday, June 4, 2008 9:18 AM
WEEKLY TIMER Operation
■ To use WEEKLY TIMER operation
• Make sure the day of the week and time are set.
If not, set the day of the week and time. (page 8.)
Program 1
Program 2 Program 3
ON
[Monday]
OFF
OFF
25˚C
6:00
Program 4
ON
27˚C
8:30
1. Press “
17:30
22:00
button”.
• The day of the week and the reservation
number will be displayed.
• 1 to 4 settings can be made per day.
2. Press the “SELECT button” to select the desired
day of the week and reservation number.
• Pressing the “SELECT button” changes the
reservation number and the day of the week.
3. Press “NEXT button”.
• The day of the week will be set.
• “
” and “
1
” blink.
4. Press “SELECT button” to
select the desired mode.
• “
” and “
ON
ON TIMER
” or “
OFF
OFF TIMER
3, 5, 7
” will flash.
2, 4, 6
Blank
no setting
• Go to STEP 9 if “no setting” is selected.
5. Press “NEXT button”.
• The weekly mode will be set.
• “
” and “
” blink.
6. Press “SELECT button” to select the desired time.
• The time can be set between 0:00 and 23:50 in 10 minute intervals.
• Press “BACK button” to return to the mode setting.
• Go to STEP 9 if “OFF” is selected at STEP 4.
7. Press “NEXT button”.
• The time will be set.
• “
” and the temperature blink.
Respective Setting Screens
Day and number settings
20
ON/OFF settings
Time settings
Temperature settings
01_EN_3P232453-1.fm Page 21 Wednesday, June 4, 2008 9:18 AM
8. Press “SELECT button” to
select the desired temperature.
• The temperature can be set between
10°C and 32°C.
Cooling: The unit operates at 18°C even
if it is set at 10 to 17°C.
Heating: The unit operates at 30°C even
if it is set at 31 to 32°C.
• To return to the time setting, press
“BACK button”.
• The set temperature is only displayed
when the mode setting is on.
9. Press “NEXT button”.
• The temperature will be set and go to
the next reservation setting.
• To continue further settings, repeat the
procedure from STEP 2.
10.Press “
button” to
complete the setting.
• Point the remote controller toward the
air conditioner and press the buttons to
operate. The air conditioner will beep
and the operation lamp will flash.
10
9
8
NOTE
■ WEEKLY TIMER
• Do not forget to set the time on the remote control first.
• The day of the week, ON/OFF time can be set with WEEKLY TIMER. For ON-TIMER, settings
other than the above are based on the remote controller settings just before the operation.
• Both WEEKLY TIMER and ON/OFF timer cannot be used at the same time. The ON/OFF
timer has priority if it is set while WEEKLY TIMER is still active. WEEKLY TIMER is activated
after the reserved ON/OFF timer is completed.
• The “WEEKLY button” activates or deactivates the reservation.
• To set WEEKLY TIMER, press “
button” and make a reservation according to the procedures.
• Only the time and set temperature set with the weekly timer are sent with the “
button”.
Set the weekly timer only after setting the operation mode, the fan strength, and the fan
direction ahead of time.
• Up to 4 settings per day and up to 28 settings per week can be reserved with WEEKLY
TIMER. If a reservation deactivated with “WEEKLY button” is activated once again, the last
reservation mode will be used.
• Shutting the breaker off, power failure, and other similar events will render operation of the
indoor unit’s internal clock inaccurate. Reset the clock. (page 8.)
• The “BACK button” can be used only for the mode, time and temperature settings.
It cannot be used to go back to the reservation number.
21
01_EN_3P232453-1.fm Page 22 Wednesday, June 4, 2008 9:18 AM
WEEKLY TIMER Operation
■ Using copy mode
• A reservation made once can be easily
copied and the same settings used for
another day of the week.
Program 1
Program 2 Program 3
ON
[Monday]
OFF
ON
25˚C
6:00
Program 4
OFF
27˚C
8:30
17:30
22:00
COPY
Program 1 Program 2 Program 3
Program 4
OFF
ON
OFF
[Tuseday] ON
to
25˚C
27˚C
[Friday]
6:00
8:30
17:30
22:00
1. Press “
button”.
2. Press “SELECT button” to confirm
the day of the week to be copied.
3. Press “COPY button”.
1, 6
3, 5
• This activates copy mode.
• Copy whole reservation of the selected
day of the week.
4. Press “SELECT button” to select
the destination day of the week.
5. Press “COPY button”.
2, 4
• The reservation will be copied to the
selected day of the week. The whole reservation of the selected day of the week will be copied.
• To continue copying the settings to other days of the week, repeat STEP 4 and STEP 5.
6. Press “
button”.
• Exit copy mode.
Setting Screens
Confirmation screen
Copy screen
Paste screen
Normal screen
NOTE
■ COPY MODE
• The entire reservation of the source day of the week is copied in the copy mode.
Detailed settings can be made after the copy is completed.
22
01_EN_3P232453-1.fm Page 23 Wednesday, June 4, 2008 9:18 AM
■ Confirming a reservation
• The reservation can be confirmed.
1. Press “
button”.
• The day of the week and the reservation
number of the current day will be displayed.
2. Press “SELECT button” to select
the day of the week and the
reservation number to be confirmed.
• Pressing the “SELECT button” displays
the reservation details.
3. Press “
button”.
• Reservation confirmation complete.
Setting Screens
■ Canceling all
reservations
1, 3
4, 6, 7
4. Hold the “WEEKLY button” for
5 seconds.
• Be sure to direct the remote control
toward the main unit and check for a
receiving tone.
• This operation is not effective while WEEKLY TIMER is being set.
• All reservations will be canceled.
2, 5
■ Canceling individual reservations
• This function can be used for canceling reservations for each day of the week.
• It can be used while confirming or setting reservations.
5. Select the day of the week to be canceled with the “SELECT button”.
6. Hold the “WEEKLY button” for 5 seconds.
• The selected reservation will be canceled.
■ To cancel WEEKLY TIMER operation
7. Press “WEEKLY button” to deactivate the WEEKLY operation.
• The “
” will disappear from the display.
• The TIMER lamp goes off.
• To reactivate the WEEKLY TIMER operation, press the “WEEKLY button” again.
23
01_EN_3P232453-1.fm Page 24 Wednesday, June 4, 2008 9:18 AM
Note for Multi System
〈〈 What is a “Multi System”? 〉〉
This system has one outdoor unit connected to
multiple indoor units.
A
room
Outdoor
unit
■ Selecting the operation mode
1. With the Priority Room Setting
present but inactive or not present.
B
room
Living
room
C
room
When more than one indoor unit is operating, priority is given to the first unit that was turned on.
In this case, set the units that are turned on later
to the same operation mode (*1) as the first unit.
Otherwise, they will enter the Standby Mode, and the operation lamp will flash; this does not indicate malfunction.
(*1)
• COOL, DRY and FAN mode may be used at the same time.
• AUTO mode automatically selects COOL mode or HEAT mode based on the room temperature.
Therefore, AUTO mode is available when selecting the same operation mode as that of the room
with the first unit to be turned on.
〈CAUTION〉
Normally, the operation mode in the room where the unit is first run is given priority, but the
following situations are exceptions, so please keep this in mind.
If the operation mode of the first room is FAN Mode, then using Heating Mode in any room after this will give priority to
heating. In this situation, the air conditioner running in FAN Mode will go on standby, and the operation lamp will flash.
2. With the Priority Room Setting active.
See “Priority Room Setting” on the next page.
■ NIGHT QUIET Mode (Available only for cooling operation)
NIGHT QUIET Mode requires initial programming during installation. Please consult your retailer or dealer for assistance.
NIGHT QUIET Mode reduces the operation noise of the outdoor unit during the night time hours to
prevent annoyance to neighbors.
• The NIGHT QUIET Mode is activated when the temperature drops 5°C or more below the highest temperature
recorded that day. Therefore, when the temperature difference is less than 5°C, this function will not be activated.
• NIGHT QUIET Mode reduces slightly the cooling (heating) efficiency of the unit.
■ OUTDOOR UNIT QUIET operation (page 15.)
1. With the Priority Room Setting present but inactive or not present.
When using the OUTDOOR UNIT QUIET operation feature with the Multi system, set all
indoor units to OUTDOOR UNIT QUIET operation using their remote controllers.
When clearing OUTDOOR UNIT QUIET operation, clear one of the operating indoor units using their remote controller.
However OUTDOOR UNIT QUIET operation display remains on the remote controller for other rooms.
We recommend you release all rooms using their remote controllers.
2. With the Priority Room Setting active.
See “Priority Room Setting” on the next page.
■ Cooling / Heating mode lock (Available only for heat pump models)
The Cooling / Heating Mode Lock requires initial programming during installation.Please consult your retailer or dealer
for assistance. The Cooling / Heating Mode Lock sets the unit forcibly to either Cooling or Heating Mode. This function
is convenient when you wish to set all indoor units connected to the Multi system to the same operation mode.
24
01_EN_3P232453-1.fm Page 25 Wednesday, June 4, 2008 9:18 AM
■ Priority Room Setting
The Priority Room Setting requires initial programming during installation. Please consult your
retailer or dealer for assistance.
The room designated as the Priority Room takes priority in the following situations;
1. Operation mode Priority.
As the operation mode of the Priority Room takes precedence, the user can select a different
operation mode from other rooms.
〈Example〉
* Room A is the Priority Room in the examples.
When COOL mode is selected in Room A while operating the following modes in Room B,C and D:
Operation mode in Room
B, C and D
COOL or DRY or FAN
Status of Room B, C and D when the unit in Room
A is in COOL mode
Current operation mode maintained
HEAT
The unit enters Standby Mode. Operation resumes when
the Room A unit stops operating.
AUTO
If the unit is set to COOL mode, operation continues. If set
to HEAT mode, it enters Standby Mode. Operation
resumes when the Room A unit stops operating.
2. Priority when POWERFUL operation is used.
〈Example〉
* Room A is the Priority Room in the examples.
The indoor units in Rooms A,B,C and D are all operating. If the unit in Room A enters
POWERFUL operation, operation capacity will be concentrated in Room A. In such a case,
the cooling (heating) efficiency of the units in Rooms B,C and D may be slightly reduced.
3. Priority when using OUTDOOR UNIT QUIET operation.
〈Example〉
* Room A is the Priority Room in the examples.
Just by setting the unit in Room A to QUIET operation, the air conditioner starts OUTDOOR
UNIT QUIET operation.
You don’t have to set all the operated indoor units to QUIET operation.
25
01_EN_3P232453-1.fm Page 26 Wednesday, June 4, 2008 9:18 AM
CARE
Care and Cleaning
CAUTION
Before cleaning, be sure to stop the operation and
turn the breaker OFF.
Units
■ Indoor unit, Outdoor unit and Remote controller
1. Wipe them with dry soft cloth.
■ Front panel
1. Open the front panel.
• Slide the two stoppers on the left and right
sides inward until they click.
2. Remove the front panel.
• Remove the string.
• Allowing the front panel to fall forward will
enable you to remove it.
String
3. Clean the front panel.
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the front panel with water,
dry it with cloth, dry it up in the shade after
washing.
4. Attach the front panel.
• Insert the front panel into the grooves of the
unit (3 places).
• Attach the string to the right, inner-side of the
front grille.
• Close the panel slowly.
String
Place front
panel in
grooves.
CAUTION
• Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an
injury.
• When removing or attaching the front panel, use a robust and stable stool and watch your
steps carefully.
• When removing or attaching the front panel, support the panel securely with hand to prevent
it from falling.
• For cleaning, do not use hot water above 40°C, benzine, gasoline, thinner, nor other volatile
oils, polishing compound, scrubbing brushes, nor other hand stuff.
• After cleaning, make sure that the front panel is securely fixed.
26
01_EN_3P232453-1.fm Page 27 Wednesday, June 4, 2008 9:18 AM
Filters
1. Open the front panel. (page 26.)
2. Remove the air filter.
• Press the claws on the right and left of the air
filter down slightly, then pull upward.
3. Take off the Titanium Apatite
Photocatalytic Air-Purifying Filter.
• Hold the tabs of the frame, and remove the
claws in 4 places.
4. Clean or replace each filter.
See figure.
5. Set the air filter and Titanium Apatite
Photocatalytic Air-Purifying Filter as
they were and close the front panel.
Titanium Apatite
Photocatalytic
Air-Purifying
Filter
Air filter
• Operation without air filters may result in
troubles as dust will accumulate inside the
indoor unit.
■ Air Filter
1. Wash the air filters with water or clean them with
vacuum cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every 2 weeks.
■ Titanium Apatite Photocatalytic
Air-Purifying Filter
The Titanium Apatite Photocatalytic Air-Purifying Filter can be renewed by washing it with water
once every 6 months. We recommend replacing it once every 3 years.
[ Maintenance ]
1. Vacuum dusts, and soak in warm water or water for about 10 to 15
minutes if dirt is heavy.
2. Do not remove filter from frame when washing with water.
3. After washing, shake off remaining water and dry in the shade.
4. Since the material is made out of paper, do not wring out the filter when removing water from it.
[ Replacement ]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
27
01_EN_3P232453-1.fm Page 28 Wednesday, June 4, 2008 9:18 AM
NOTE
• Operation with dirty filters:
(1) cannot deodorize the air.
(2) cannot clean the air.
(3) results in poor heating or cooling. (4) may cause odour.
• To order Titanium Apatite Photocatalytic Air-Purifying Filter contact to the service shop
there you bought the air conditioner.
• Dispose of old filters as flammable waste.
Item
Titanium Apatite Photocatalytic Air-Purifying Filter
(without frame) 1 set
Part No.
KAF968A42
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and
consult the service shop if this is the case.
■ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the
inside.
• Press “MODE” button and select “FAN”operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote controller.
NOTE
• When a multi outdoor unit is connected, make sure the heating operation is not used at
the other room befure you use the fan operation. (page 24.)
28
01_EN_3P232453-1.fm Page 29 Wednesday, June 4, 2008 9:18 AM
TROUBLE SHOOTING
Trouble Shooting
These cases are not troubles.
The following cases are not air conditioner troubles but have some reasons. You may just continue using it.
Case
Explanation
Operation does not start soon. • This is to protect the air conditioner.
• When ON/OFF button was pressed
You should wait for about 3 minutes.
soon after operation was stopped.
• When the mode was reselected.
Hot air does not flow out soon
after the start of heating
operation.
• The air conditioner is warming up. You should wait for 1 to 4 minutes.
(The system is designed to start discharging air only after it
has reached a certain temperature.)
The heating operation stops suddenly • The system is taking away the frost on the outdoor unit.
You should wait for about 4 to 12 minutes.
and a flowing sound is heard.
The outdoor unit emits water or
steam.
■ In HEAT mode
• The frost on the outdoor unit melts into water or steam
when the air conditioner is in defrost operation.
■ In COOL or DRY mode
• Moisture in the air condenses into water on the cool
surface of outdoor unit piping and drips.
Mist comes out of the indoor
unit.
■ This happens when the air in the room is cooled into mist by
the cold airflow during cooling operation.
■ This is because the air in the room is cooled by the heat
exchanger and becomes mist during defrost operation.
The indoor unit gives out odour. ■ This happens when smells of the room, furniture, or cigarettes
are absorbed into the unit and discharged with the airflow.
(If this happens, we recommend you to have the indoor unit washed by a
technician. Consult the service shop where you bought the air conditioner.)
The outdoor fan rotates while
the air conditioner is not in
operation.
■ After operation is stopped:
• The outdoor fan continues rotating for another 60 seconds
for system protection.
■ While the air conditioner is not in operation:
• When the outdoor temperature is very high, the outdoor
fan starts rotating for system protection.
The operation stopped
suddenly.
(OPERATION lamp is on.)
■ For system protection, the air conditioner may stop operating
on a sudden large voltage fluctuation.
It automatically resumes operation in about 3 minutes.
No remote controller signals are • The batteries are dying and the remote controller is malfunctioning. Replace all the batteries with new size AAA alkaline
displayed.
The remote controller sensitivity is low.
batteries. For details, refer to “To set the batteries” of this
manual. (page 7.)
The display is low in contrast or
* If the reset button is provided, press the reset button after the
blacked out.
batteries are replaced.
The display runs out of control.
The ON/OFF TIMER does not
operate according to the
settings.
• Check if the ON/OFF TIMER and the WEEKLY TIMER are
set to the same time.
Change or disable the settings in the WEEKLY TIMER.
(page 20.)
29
01_EN_3P232453-1.fm Page 30 Wednesday, June 4, 2008 9:18 AM
Check again.
Please check again before calling a repair person.
Case
The air conditioner does not
operate.
(OPERATION lamp is off.)
Check
•
•
•
•
Hasn’t a breaker turned OFF or a fuse blown?
Isn’t it a power failure?
Are batteries set in the remote controller?
Is the timer setting correct?
Cooling (Heating) effect is poor. • Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
• Is the temperature setting appropriate?
• Are the windows and doors closed?
• Are the airflow rate and the air direction set appropriately?
Operation stops suddenly.
(OPERATION lamp flashes.)
• Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
Clean the air filters or take all obstacles away and turn the
breaker OFF. Then turn it ON again and try operating the air
conditioner with the remote controller. If the lamp still flashes,
call the service shop where you bought the air conditioner.
• Are operation modes all the same for indoor units connected
to outdoor units in the multi system?
If not, set all indoor units to the same operation mode and
confirm that the lamps flash.
Moreover, when the operation mode is in “AUTO”, set all
indoor unit operation modes to “COOL” or “HEAT” for a
moment and check again that the lamps are normal.
If the lamps stop flashing after the above steps, there is no
malfunction.
(page 24.)
An abnormal functioning
happens during operation.
• The air conditioner may malfunction with lightning or radio
waves. Turn the breaker OFF, turn it ON again and try
operating the air conditioner with the remote controller.
30
01_EN_3P232453-1.fm Page 31 Wednesday, June 4, 2008 9:18 AM
Call the service shop immediately.
WARNING
■ When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.
Continued operation in an abnormal condition may result in troubles, electric shocks or fire.
Consult the service shop where you bought the air conditioner.
■ Do not attempt to repair or modify the air conditioner by yourself.
Incorrect work may result in electric shocks or fire.
Consult the service shop where you bought the air conditioner.
If one of the following symptoms takes place, call the service shop immediately.
■ The power cord is abnormally hot or damaged.
■ An abnormal sound is heard during operation.
■ The safety breaker, a fuse, or the earth leakage breaker
cuts off the operation frequently.
■ A switch or a button often fails to work properly.
■ There is a burning smell.
■ Water leaks from the indoor unit.
■ After a power failure
The air conditioner automatically resumes
operation in about 3 minutes. You should just
wait for a while.
Turn the breaker
OFF and call the
service shop.
■ Lightning
If lightning may strike the neighbouring area,
stop operation and turn the breaker OFF for
system protection.
We recommend periodical maintenance.
In certain operating conditions, the inside of the air conditioner may get foul after several seasons of
use, resulting in poor performance. It is recommended to have periodical maintenance by a specialist
aside from regular cleaning by the user. For specialist maintenance, contact the service shop where
you bought the air conditioner.
The maintenance cost must be born by the user.
31
01_EN_3P232453-1.fm Page 32 Wednesday, June 4, 2008 9:18 AM
MEMO
32
00_CV_3P232453-1.fm Page 2 Wednesday, June 4, 2008 3:09 PM
Two-dimensional bar code is a code
for manufacturing.
3P232453-1 M08B034
(0808) HT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising