AL-CAT5W Installation
www.L-com.com
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the equipment you are installing.
IMPORTANT: Look over the site before beginning any installation, and anticipate possible hazards, especially these:
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are anywhere where possible contact
can be made. Antennas, masts, towers, guy wires or cables may lean or fall and contact these lines. People may be injured or
killed if they are touching or holding any part of equipment when it contacts electric lines. Make sure there is NO possibility
that equipment or personnel can come in contact directly or indirectly with power lines.
Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of the
mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
•
•
•
•
•
•
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting ladders and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by
calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO ANTENNAS
HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment
connected to the antenna.
•
•
•
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 1 O AWG
ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
Lightning arrestors for antenna feed coaxial cables are available from HyperLink Technologies, Inc.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
•
•
•
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency medical aid has been requested.
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
www.L-com.com
AL-CAT5W Connection Diagram
Terminal Strip* RJ-45 Jack*
RJ-45 Jack*
Terminal Strip*
*Unit provides protection
to both sides equally.
EQUIPMENT SIDE
LINE SIDE
Application Note:
This unit will not work with Cisco®
Power Over Ethernet Injectors.
To Ground
We recommend HyperLink Technologies'
Cisco® compatible BT-CAT5-P1R DC Injector.
CAT5 Cables
(Terminated or Unterminated)
AIP-00040 Rev. D – 09/06 Page 2/5
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
www.L-com.com
AL-CAT5W Installation Instructions
1. Position the suppressor with the strain reliefs down
when mounting.
2. The data cable can be connected to the suppressor
via the RJ45 jacks or terminal strips.
For use with Terminal Strip: Install the data cable
through the strain reliefs, strip back cable jackets as
needed and terminate the data wires to the screw down
terminal blocks (Pinouts located next to terminal strip).
Terminal strips can be removed to ease wiring.
For use with RJ45 jacks: Install the data cable through
the strain reliefs and then terminate with RJ45 connectors.
Pinouts for jacks are as follows:
CAT5 Pinout:
1 - Data 1 +
2 - Data 1 3 - Data 2 +
6 - Data 2 4 - DC 1
5 - DC 1
7 - DC 2
8 - DC 2
RJ-45
1
2
3
4
5
6
7
8
RJ-45
EQUIPMENT
SIDE
LINE SIDE
TERMINAL
STRIP
1
2
3
4
5
6
7
8
DIODE CLAMP
ARRAY
8
7
6
5
4
3
2
1
TERMINAL
STRIP
3. Adjust the cable inside the of the unit to ensure proper closing
of cover, then secure by tightening strain reliefs onto cables.
4. Attach cover using the provided hardware.
5. To ensure proper operation of suppressor,
install an earth ground to the external ground
lug on the unit.
Note: This unit provides Bi-Directional Protection,
input and output cables may be interchanged.
AIP-00040 Rev. D – 09/06 Page 3/5
EARTH GROUND
Application Note:
This unit will not work with Cisco® Power Over Ethernet Injectors.
We recommend HyperLink Technologies' Cisco® compatible
BT-CAT5-P1R DC Injector.
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
www.L-com.com
CAT5 Cable Reference
CAT5 (EIA 568-B) Cable
RJ45 Pin/Color
LINE
EQUIPMENT
RJ45 Pin/Color
1 WHT/ORG
DATA PAIR 1 +
DATA PAIR 1 +
1 WHT/ORG
2 ORG
DATA PAIR 1 -
DATA PAIR 1 -
2 ORG
3 WHT/GRN
DATA PAIR 2 +
DATA PAIR 2 +
3 WHT/GRN
6 GRN
DATA PAIR 2 -
DATA PAIR 2 -
6 GRN
5 WHT/BLU
DC 1
DC 1
5 WHT/BLU
4 BLU
DC 1
DC 1
4 BLU
7 WHT/BRN
DC 2
DC 2
7 WHT/BRN
8 BRN
DC 2
DC 2
8 BRN
AL-CAT5W Lightning Protector
CAT5 (EIA 568-A) Cable
RJ45 Pin/Color
LINE
EQUIPMENT
RJ45 Pin/Color
1 WHT/GRN
DATA PAIR 1 +
DATA PAIR 1 +
1 WHT/GRN
2 GRN
DATA PAIR 1 -
DATA PAIR 1 -
2 GRN
3 WHT/ORG
DATA PAIR 2 +
DATA PAIR 2 +
3 WHT/ORG
6 ORG
DATA PAIR 2 -
DATA PAIR 2 -
6 ORG
5 WHT/BLU
DC 1
DC 1
5 WHT/BLU
4 BLU
DC 1
DC 1
4 BLU
7 WHT/BRN
DC 2
DC 2
7 WHT/BRN
8 BRN
DC 2
DC 2
8 BRN
AL-CAT5W Lightning Protector
AIP-00040 Rev. D – 09/06 Page 4/5
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
www.L-com.com
AL-CAT5W Dimensions
5.840" (2X)
.237"
.592"
1.973" (2X)
3.157"
4.157"
Cable Conduit
BOTTOM VIEW
TOP VIEW
Ground Clamp
.176" Dia. Mounting Holes (4x)
Mounting Screw (4x)
(#6 or M3.5 Pan Hd.)
6.313"
2.170"
1.680"
.980" (2X)
2.950"
(Cover Removed)
SIDE VIEW
AIP-00040 Rev. D – 09/06 Page 5/5
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement