NAD T571 User Guide Manual Operating Instruction Pdf

NAD T571 User Guide Manual Operating Instruction Pdf
T 571
DVD / CD / MP3 Player
GB Owner’s Manual
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 2
INTRODUCTION
Safety Precautions
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated ‘dangerous voltage’ within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOUD.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference, should the unit require maintenance, contact an authorized service location-see
service procedure.
Use of controls, adjustments or the performance of procedures other than those specified herein
may result hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation
when open. DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING:
Changes or modifications not expressly approved by NAD Electronics Corporation could void the
user’s authority to operate the equipment.
INDUSTRY CANADA REQUIREMENT:
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numéruque de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
RECORD YOUR MODEL NUMBER (Now, while you can see it)
The model and serial number of your new DVD
player are located on the back of the DVD player cabinet. For your future convenience, we suggest that you record these numbers here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
Downloaded From DvDPlayer-Manual.com NAD Manuals
INTRODUCTION
PAGE 3
Table of Contents
Introduction
Basic Operations
❏
❏
❏
❏
❏
❏
❏
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT SAFETY INSTRUCTIONS . . . . . . 4-5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Identification of Controls . . . . . . . . . . . . . . . . . 8-11
Front Panel/Display Window . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparing the Remote Control . . . . . . . . . . . . . . . . . . 11
Operating with the Remote Control . . . . . . . . . . . . . . 11
Connections
❏
Connecting to Surround Sound System . . . . . 12-14
Enjoying Dolby Digital Sound. . . . . . . . . . . . . . . . . . . 12
Enjoying Dolby Pro Logic Surround Sound . . . . . . . . 13
Enjoying 2 Channel Digital Stereo Sound. . . . . . . . . . 14
Enjoying DTS Sound . . . . . . . . . . . . . . . . . . . . . . . . . 14
❏
❏
Connecting to a Stereo System . . . . . . . . . . . . . 15
Connecting to a TV equipped with component
video inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
❏
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 17
Initial Settings
❏
❏
❏
❏
❏
❏
❏
❏
❏
Selection of Initial Settings . . . . . . . . . . . . . . . . . 18
Selecting Disc Languages . . . . . . . . . . . . . . . . . 19
Selecting Parental Control Rating Level and
Password . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Selecting TV Aspect . . . . . . . . . . . . . . . . . . . . . . 22
Selecting Menu Language . . . . . . . . . . . . . . . . . 23
Selecting Progressive Scan . . . . . . . . . . . . . . . . 24
Selecting Digital Audio Output . . . . . . . . . . . . . . 25
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table of Languages and Their Abbreviations . . . 27
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . 28-31
Stopping Play. . . . . . . . . . . . . . . . . . . . . . . . . . 30
Resume Play . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Last Scene Memory . . . . . . . . . . . . . . . . . . . . . 30
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Skipping Discs . . . . . . . . . . . . . . . . . . . . . . . . . 31
Exchanging the Disc and Starting Playback . . . . 31
❏ Special Playback. . . . . . . . . . . . . . . . . . . . . . 32-33
Still Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Frame Advance . . . . . . . . . . . . . . . . . . . . . . . . 32
Skipping Chapters and Tracks Forward or Back. 32
HDCD Playback . . . . . . . . . . . . . . . . . . . . . . . . 32
To Scan at Fast Forward or Fast Reverse Playback . 33
Playing in Slow-Motion . . . . . . . . . . . . . . . . . . . 33
Operation Using GUI (Graphical User
Interface) Menu Icons
❏
❏
General Information about GUI Menu Icons . . . . 34
Detailed Description of each GUI Menu Icon . . . 35
Advanced Operation
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Using a Title Menu . . . . . . . . . . . . . . . . . . . . . . . 36
Using a DVD Menu . . . . . . . . . . . . . . . . . . . . . . 36
Changing Subtitle Language . . . . . . . . . . . . . . . 37
Changing Audio Soundtrack Language. . . . . . . . 37
Viewing from another Angle . . . . . . . . . . . . . . . . 38
Producing a 3D Surround Effect . . . . . . . . . . . . . 38
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Storing Markers in Memory to be Viewed
(Listened to) again . . . . . . . . . . . . . . . . . . . . . . . 40
Zoom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Random Play . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Playback with MP3 . . . . . . . . . . . . . . . . . . . . 43-44
Reference
❏
Disc Requirements/Copyright Information . . . . . . 45
Before Calling Service Personnel . . . . . . . . . . . . 46
❏ Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 47
❏
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 4
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL
AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire
hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation,
use and servicing.
This unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s
manual carefully, and follow all the operating and
other instructions.
2. Power Sources
This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply in your
home, consult your product dealer or local power
company. For products intended to operate from
battery power, or other sources, refer to the
operating instructions.
3. Grounding or Polarization
This product is equipped with a polarized alternating
current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from overheating. These
openings must not be blocked or covered. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
5. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
Downloaded From DvDPlayer-Manual.com NAD Manuals
6. Water and Moisture
Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink. or laundry
tub; in a wet basement; or near a swimming pool
and the like.
7. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, playing particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
9. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
10. Lightning
For added protection of this product during storms, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet.
This will prevent damage to the product due to
lightning and power-line surges.
11. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any kind
on the product.
12. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
INTRODUCTION
PAGE 5
IMPORTANT SAFETY INSTRUCTIONS (Cont’d)
13. Accessories, Carts, and Stands
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product
may fall, causing serious
injury to a child or adult, and
serious damage to the
product. Use only with a cart,
stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer. A product and cart combination should
be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product and
cart combination to overturn.
14. Disc Tray
Keep your fingers well clear of the disc tray as it is
closing. It may cause serious personal injury.
15. Burden
Do not place a heavy object on or step on the
product. The object may fall, causing serious
personal injury and serious damage to the product.
16. Connecting
When you connect the product to other equipment,
turn off the power and unplug all of the equipment
from the wall outlet. Failure to do so may cause an
electric shock and serious personal injury. Read the
owner’s manual of the other equipment carefully and
follow the instructions when making any
connections.
17. Sound Volume
Reduce the volume to the minimum level before you
turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
18. Sound Distortion
Do not allow the product to output distorted sound
for a longtime. It may cause speaker overheating
and fire.
19. Headphones
When you use the headphones, keep the volume at
a moderate level. If you use the headphones
continuously with high volume sound, it may cause
hearing damage.
Downloaded From DvDPlayer-Manual.com NAD Manuals
20. Laser Beam
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of
the laser beam. It may cause sight damage.
21. Disc
Do not use a cracked, deformed, or repaired disc.
These discs are easily broken and may cause serious personal injury and product malfunction.
22. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have fallen
into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e) If the product has been dropped or damaged in
any way.
f) When the product exhibits a distinct change in
performance-this indicates a need for service.
23. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
24. Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
25. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
PAGE 6
INTRODUCTION
Precautions
Notes on handling
❏
❏
❏
❏
❏
When shipping the DVD player, always use the
original shipping carton and packing materials.
For maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic
products in contact with the DVD player for a long
time. They will leave marks on the finish.
The top and rear panels of the DVD player may
become warm after a long period of use. This is
normal and not a malfunction.
When the DVD player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on
and use the DVD player occasionally.
Notes on Locating
❏
Notes on Moisture Condensation
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when
you pour a cold drink into a glass on a warm day.
Drops of water form on the outside of the glass. In
the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD player.
Exa
Notes on Cleaning
Use a soft, dry cloth for cleaning.
❏ For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry. Do not use any type of solvent, such as thinner
and benzine, as they may damage the surface of the
DVD player.
❏ If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
Warning: Cleaning and adjustment of lenses and/or
other components of playback mechanism should
be performed by a qualified service technician.
❏
❏
❏
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot
and humid place just after you move the unit from
an air conditioned room.
When you use the DVD player in a humid place.
It’ s to o
wa rm !
❏
Do not use the DVD player when moisture condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player and leave it “ON” for
two or three hours. After two or three hours, the
DVD player will have warmed up and evaporated
any moisture. Keep the DVD player connected to
the wall outlet and moisture condensation will seldom occur.
Wa
Downloaded From DvDPlayer-Manual.com NAD Manuals
Optical
p lens
pick-u
Moisture condensation occurs during the following
cases.
❏
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, move the DVD
player away from the TV, radio, or VCR.
mples of moistur
e
ensation
cond
it!
INTRODUCTION
PAGE 7
Notes on Discs
This section shows you how to handle, clean, and store discs.
On Handling Discs
❍
Do not touch the playback side of the disc.
On Storing Discs
❍
❍
❍
❍
Do not attach paper or tape to discs.
On Cleaning Discs
❍
❍
❍
Do not store discs in a place subject to
direct sunlight or near heat sources.
Do not store discs in places subject to
moisture and dust such as a bathroom or
near a humidifier.
Store discs vertically in a case. Stacking or
placing objects on discs outside of their
case may cause warping.
Fingerprints and dust on the disc cause
picture and sound deterioration. Wipe the
disc from the center outward with a soft
cloth. Always keep the disc clean.
If you cannot wipe off the dust with a soft
cloth, wipe the disc lightly with a slightly
moistened soft cloth and finish with a dry
cloth.
Do not use any type of solvents such as
thinner, benzine, commercially available
cleaners or anti-static spray for vinyl LPs.
They may damage the disc.
Downloaded From DvDPlayer-Manual.com NAD Manuals
About This Owner’s Manual
❍
❍
❍
This owner’s manual explains the basic
instructions of this DVD player.
Some DVD video discs have functions that
may not be explained in this owner’s manual.
Therefore, some instructions may differ from
this owner’s manual, and there may be extra
instructions. In this case, follow the instructions
displayed on the TV screen or package.
“
” may appear on the TV screen
during operation. This icon means the
function explained in this owner’s manual is
not available on that specific DVD video
disc.
PAGE 8
INTRODUCTION
Identification of Controls
Front Panel
POWER indicator
MENU button
SKIP buttons
RANDOM button
REPEAT button
ARROW
buttons
PAUSE button
PLAY button
Remote sensor
SELECT/
ENTER
button
Display window
POWER button
OPEN/CLOSE button
Disc tray
STOP button
SCAN buttons
NEXT DISC button
Display Window
MP3 indicator
PROGRAM indicator
HDCD indicator
Operating
status
indicator
RANDOM indicator
Repeat playback
mode indicators
CD indicator
DVD indicator
MP3
HD CD DVD
1
2
3
TITLE
CHP/TRK
PROG.
RANDOM ALL A
B
5
4
Total playing time/elapsed time indicators
Disc 1-5 indicator
Angle icon indicator
Downloaded From DvDPlayer-Manual.com NAD Manuals
Chapter/Track number indicator
Title number indicator
INTRODUCTION
PAGE 9
Identification of Controls (Cont’d)
Rear Panel
12V TRIGGER INPUT jack
By connecting this DVD player to another
NAD audio component or system controller
equipped with a 12V trigger output, you can
remotely operate the T 571 power ON/OFF.
VIDEO OUT jack
COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks
S-VIDEO OUT jack
VIDEO OUTPUT SELECT
switch
12V
TRIGGER
IN
COAXIAL DIGITAL
AUDIO OUT jack
POWER CORD
Connect to an AC 120V, 60Hz
outlet only.
AUDIO OUT (L/R) jacks (1, 2)
OPTICAL DIGITAL AUDIO OUT jack
Remove the dust protection cap from the connector
and connect the optical digital cable (not supplied)
securely so that the configurations of both the cable
and the connector match. Keep the dust protection
cap and always reattach the cap when not using the
connector to protect against dust intrusion.
Dust protection cap
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 10
INTRODUCTION
Identification of Controls (Cont’d)
Remote Control
You will find instructions for each of the remote control functions in the appropriate sections of this instruction manual.
POWER button
OPEN/CLOSE button
REPEAT button
A-B button
SETUP button
SUBTITLE button
POWER
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
AUDIO button
RANDOM button
ANGLE button
SOUND button
TITLE
MENU
***TITLE button
*MENU button
SELECT/ENTER button
**ARROW buttons
SELECT
ENTER
DISPLAY button
RETURN button
DISPLAY
RETURN
ZOOM button
MARKER-SEARCH button
ZOOM
MARKER — SEARCH
FWD/REV SCAN button
PLAY button
SCAN
PLAY
SKIP
STOP button
FWD/REV SKIP button
STOP
PAUSE/STEP button
NEXT DISC PAUSE/STEP
SLOW
NEXT DISC button
SLOW buttons
PROGRAM button
1
2
3
4
5
6
7
8
Number buttons
CLEAR button
CLEAR
0
***TITLE button
Use the TITLE button to display the
title screen included on DVD video
discs. To operate a menu screen,
follow the instructions in “Using a
Title Menu” (page 36).
Downloaded From DvDPlayer-Manual.com NAD Manuals
9
PROGRAM
*MENU button
Use the MENU button to display the
menu screen included on DVD
video discs. To operate a menu
screen,
follow the instructions in “Using a
DVD Menu” (page 36).
** Directional arrow buttons
(up, down, left, right) for use in
highlighting a selection on a GUI
menu screen, TITLE and MENU
screen.
INTRODUCTION
PAGE 11
Identification of Controls (Cont’d)
Preparing the Remote Control
Insert the batteries into the remote control so you can
use it to operate the DVD player.
1
Open the battery cover.
2
Insert batteries (AAA size).
Operating with the Remote Control
This section shows you how to use the remote control.
Point the remote control at the
remote sensor and press the
buttons.
30° 30°
Within about 23 ft (about 7 m)
POWER
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
● Make sure to match the + and - on the batteries to
the marks inside the battery compartment.
3
Close the cover.
Distance: About 23 ft (7 m) from the front of the remote
sensor
Angle:
About 30° in each direction of the front of the
remote sensor
* Do not expose the remote sensor of the DVD
player to a strong light source such as direct
sunlight or illumination. If you do so, you may not
be able to operate the DVD player with the remote
control.
Notes on the remote control
Notes on batteries
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Improper use of batteries may cause battery leakage and
corrosion.
To operate the remote control correctly, follow the
instructions.
Do not insert the batteries into the remote control in the
wrong direction.
Do not charge, heat, open, or short-circuit the batteries.
Do not throw the batteries into fire.
Do not leave dead or exhausted batteries in the remote
control.
Do not use different types of batteries together, or mix
old and new batteries.
If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage
from battery corrosion.
If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
The batteries should last about one year with normal
use.
Downloaded From DvDPlayer-Manual.com NAD Manuals
MENU
SELECT
ENTER
❍
❍
❍
❍
❍
Point the remote control at the remote sensor on the
DVD player.
Do not drop or give the remote control a shock.
Do not leave the remote control near an extremely hot or
humid place.
Do not spill water or put anything wet on the remote control.
Do not disassemble the remote control.
PAGE 12
CONNECTIONS
Connecting to Surround Sound System
Enjoying Dolby Digital Sound
You can enjoy the high quality dynamic sound of Dolby Digital, Dolby Pro Logic, and 2 Channel Digital Stereo.
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to
reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this
dynamic realistic sound by connecting the DVD player to a 5.1 channel receiver equipped with a Dolby Digital decoder
or Dolby Digital processor.
12V
TRIGGER
IN
To DIGITAL OUT
(COAXIAL or OPTICAL)
To S-VIDEO OUT
or VIDEO OUT
75 ohm coaxial cable
or Optical cable
Receiver equipped
with a Dolby Digital
decoder
S-Video cable
or Video cable
Connection
example
To digital
audio input
To S-video Input
or Video Input
To enjoy Dolby Digital sound
from this DVD player you need
the following:
Front speaker
(left)
Front speaker
(right)
Center
speaker
● DVD recorded in Dolby Digital
● 5.1 channel receiver equipped
with a Dolby Digital decoder,
or Dolby Digital processor and
power receiver
Sub woofer
Rear speaker
(left surround)
Rear speaker
(right surround)
● 5 speakers and 1 sub woofer
To enjoy Dolby Digital sound
You need to select “Dolby Digital”
on the SETUP menu.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished works. Copyright 1992-1997 Dolby
Laboratories. All rights reserved.
Notes
❍
❍
❍
❍
Refer to the owner’s manual of your audio system for operating instructions.
Before you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from
the wall outlet before making any connections.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
Downloaded From DvDPlayer-Manual.com NAD Manuals
CONNECTIONS
PAGE 13
Connecting to Surround Sound System (Cont’d)
Enjoying Dolby Pro Logic Surround Sound
Dolby Pro Logic Surround
You can still enjoy the excitement of Surround Sound even if your A/V receiver does not offer Dolby Digital decoding.
If your A/V receiver has a Dolby Pro Logic decoder, refer to the following connection diagram.
12V
TRIGGER
IN
Connect one or two rear speakers.
Note: The surround effect is greatly
enhanced by using two surround speakers.
To VIDEO OUT
To AUDIO OUT
Audio cable
Video cable
To audio input
Connection example
Receiver equipped
with Dolby Pro
Logic Surround
To video input
Center speaker
Front
speaker
(right)
Front
speaker
(left)
TV
Rear speaker
(left)
●
Rear speaker
(right)
With a receiver equipped with Dolby Digital
Connect the equipment the same way as described in “Enjoying Dolby Digital Sound” on the previous page. Refer to that
receiver’s owner’s manual and set the receiver so you can enjoy Dolby Pro Logic Surround sound.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL OUT jack of this DVD
player to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well as the
speakers (Refer to “Selecting Digital Audio Output” on page 25).
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 14
CONNECTIONS
Connecting to Surround Sound System (Cont’d)
Enjoying 2 Channel Digital Stereo Sound
2 Channel Digital Stereo
You can enjoy the dynamic sound of 2 Channel Digital Stereo by connecting this DVD player to a receiver equipped with a
digital audio input and speaker system (right and left front speakers).
Connection example
75 ohm coaxial cable or
optical cable
Receiver equipped with a
digital audio input
To digital audio input
To S-video Input
or Video Input
To DIGITAL OUT
(COAXIAL or
OPTICAL)
S-Video cable
or Video cable
To S-VIDEO OUT
or VIDEO OUT
Front speaker
(left)
Front speaker
(right)
TV
12V
TRIGGER
IN
Enjoying DTS Sound
❍ Your A/V Receiver or processor must be equipped with a DTS Decoder.
❍ The digital output (see selecting digital output page 25) must be set to “stream”.
❍ The disc must have a DTS soundtrack.
Connection example
Receiver equipped
with a DTS decoder
75 ohm coaxial cable or
Optical Cable
To digital audio input
To S-video Input
or Video Input
To DIGITAL OUT
(COAXIAL or
OPTICAL)
S-Video cable
or Video cable
To S-VIDEO OUT
or VIDEO OUT
Front
speaker
(left)
Front speaker
(right)
Center
speaker
Sub woofer
12V
TRIGGER
IN
Rear speaker
(left surround)
Rear speaker
(right surround)
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
Notes
❍
❍
❍
❍
Refer to the owner’s manual of your audio system for operating instructions.
Before you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 15
CONNECTIONS
Connecting to an Stereo System
You can listen to the sound of audio CDs and DVD video discs in stereo.
To S-VIDEO OUT
12V
TRIGGER
IN
S-video cable (Not supplied)
If the TV has an S-video input, connect
the DVD player with the S-video cable.
To VIDEO OUT
To AUDIO OUT (L/R)
Audio cable
(supplied)
To audio inputs
To S-video input
Stereo system
Video cable
(supplied)
To video input
TV or monitor with
audio/video inputs
Notes
❍
❍
❍
❍
❍
Refer to the owner’s manual of your stereo system for operating instructions.
Before you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, move the DVD
player away from the tuner and radio.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL OUT jack of this DVD
player to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well as the
speakers (Refer to “Selecting Digital Audio Output” on page 25).
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 16
CONNECTIONS
Connecting to a TV equipped with component video inputs
PROGRESSIVE SCAN: Some TVs or monitors are equipped with component video inputs that are capable of
reproducing a progressively scanned video signal. Connecting to these inputs allows you to view the highest
quality pictures with less flicker.
COMPONENT VIDEO OUT: Some TVs or monitors are equipped with component video inputs. Connecting to these
inputs allows you to enjoy higher quality picture playback.
■ To switch the output signal (Progressive/Component)
Set the Progressive to “On” on the SETUP menu for Progressive signal, or set the Progressive to “Off” on the SETUP
menu for Component video signal.
VIDEO OUTPUT SELECT switch
12V
TRIGGER
IN
Video cable (Y, Pb, Pr) (not supplied)
To AUDIO OUT (L/R)
To COMPONENT VIDEO OUT/
PROGRESSIVE SCAN (Pb, Pr, Y)
When using COMPONENT VIDEO OUT/PROGRESSIVE
SCAN jack, set the VIDEO OUTPUT SELECT switch to
COMPONENT/PROGRESSIVE SCAN.
Audio/Video cable
(supplied)
To component video input or
progressive scan video input
To audio inputs
TV or monitor with component
video or progressive scan inputs
Notes
❍
❍
❍
❍
Refer to the owner’s manual of your TV for TV operating instructions.
Before you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, -Y, B-Y or Y, Cb, Cr)
In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a
case, adjust the TV or monitor for optimum performance.
Downloaded From DvDPlayer-Manual.com NAD Manuals
CONNECTIONS
PAGE 17
Connecting to a TV
Connect the DVD player to your TV.
VIDEO OUTPUT SELECT switch
To S-VIDEO OUT
12V
TRIGGER
IN
When using S-VIDEO OUT jack, set the VIDEO
OUTPUT SELECT switch to S-VIDEO.
To VIDEO OUT
To AUDIO OUT (L/R)
If the TV has an S-video input, connect
the DVD player with the S-video cable.
S-video cable
(Not supplied)
Audio/Video cable
(supplied)
To S-video input
To audio inputs
To video input
TV or monitor with
audio/video inputs
Notes
❍
❍
❍
Refer to the owner’s manual of your TV for TV operating instructions.
Before you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
Connect the DVD player to your TV directly. If you connect the DVD player to a VCR, the playback picture will be distorted
because DVD video discs are copy protected.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL OUT jack of this
DVD player to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well
as the speakers (Refer to “Selecting Digital Audio Output” on page 25).
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 18
INITIAL SETTINGS
Selection of initial settings
Once the initial settings have been completed,
the player can always be operated under the
same conditions (especially with DVD discs).
The settings will be retained in the memory until
they are changed, even if the power is switched
off.
POWER
1
Selection of initial settings
1
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
2
MENU
2, 3
RETURN
ZOOM
MARKER — SEARCH
SCAN
PLAY
SKIP
STOP
NEXT DISC PAUSE/STEP
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
5.1 Speaker Setup
Russian
Others
Other — — — —
Press D/E to select the desired item.
The screen will show the current setting for the
selected item, and the alternate setting(s).
SLOW
3
1
2
3
4
5
6
7
8
CLEAR
The SETUP menu is displayed.
• Disc Audio (see page 19.)
• Disc Subtitle (see page 19.)
• Disc Menu (see page 19.)
• Rating (see page 20.)
• Password (see page 21.)
• TV Aspect (see page 22.)
• Menu Language (see page 23.)
• Progressive Scan (see page 24.)
• Digital Audio Output (see page 25.)
• Others (see page 26.)
SELECT
ENTER
DISPLAY
Press SETUP in the stop or playback mode.
9
PROGRAM
0
Press G and then D/E to select the desired
setting and press SELECT/ENTER.
• Some items require additional steps. (See the
respective page.)
When the alternate setting is selected the screen returns to
the Initial Settings display.
To exit SETUP menu
Press SETUP, RETURN or PLAY.
Downloaded From DvDPlayer-Manual.com NAD Manuals
INITIAL SETTINGS
PAGE 19
Selecting disc languages
This is to select the audio soundtrack language,
subtitle language and the language used in title
menus or DVD menus which will always be used
for every disc to be played back.
1
At the setup screen, press D/E to select
“Disc Audio” and press G.
When you play back a DVD video disc, the DVD
player automatically displays the pre-selected
subtitle language if it is included on the disc.
POWER
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
5.1 Speaker Setup
Russian
Others
Other — — — —
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
2
Press D/E to select the desired language and
then press SELECT/ENTER.
MENU
1, 2
SELECT
ENTER
DISPLAY
RETURN
ZOOM
MARKER — SEARCH
SCAN
PLAY
SLOW
1
2
3
4
5
6
7
8
CLEAR
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
5.1 Speaker Setup
Russian
Others
Other — — — —
SKIP
STOP
NEXT DISC PAUSE/STEP
Disc Audio
Original : The original language of each disc will be selected.
English : The English will be Selected.
Other : Another language can be selected. You can input
4-number language code. (Refer to the language
codes on page 27.)
The “Disc Subtitle” and “Disc Menu” are selected by the
same method.
9
PROGRAM
Note
0
❍
Downloaded From DvDPlayer-Manual.com NAD Manuals
If the language selected is not available on the disc, the original
language designated by each disc will be selected.
PAGE 20
INITIAL SETTINGS
Selecting Parental Control Rating Levels and Password
This is to prohibit the playing of specified
DVDs which are unsuitable for children.
● Some DVD discs contain a restriction level
which enables parents to remove scenes or
prevent playback of discs by children. DVD
players are equipped with a password
designed to prevent children from changing
the level.
POWER
Selecting rating level (DVD only)
1
At the SETUP screen, press
“Rating” and press G.
D/E
Disc Audio
8
Disc Subtitle
7
Disc Menu
6
Rating
5
Password
4
TV Aspect
3
Menu Language
2
Progressive Scan
1
Digital Audio Output
Unlock
to select
5.1 Speaker Setup
OPEN/CLOSE
Others
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
2
TITLE
MENU
1, 2
SELECT
ENTER
DISPLAY
RETURN
ZOOM
MARKER — SEARCH
SCAN
PLAY
SKIP
Press D/E to select the desired level and
press SELECT/ENTER.
Disc Audio
8 Blocked
Disc Subtitle
7 Blocked
Disc Menu
6
Rating
5
Password
4
TV Aspect
3
Menu Language
2
Progressive Scan
1
Digital Audio Output
Unlock
STOP
5.1 Speaker Setup
NEXT DISC PAUSE/STEP
SLOW
1
2
3
4
5
6
7
8
CLEAR
9
Others
You cannot play DVD video discs rated higher than the level
you selected unless you cancel the parental lock function.
For example, when you select level 7, discs rated higher than
level 7 are blocked and cannot be played.
PROGRAM
0
The parent lock level is equivalent to the following USA movie
ratings.
Level 7: NC-17
Level 3: PG
Level 6: R
Level 1: G
Level 4: PG 13
• Some titles do not match with the rating level described as
above.
If you change the level and enter a password, playback of all
DVDs with ratings higher than your selection will be blocked,
unless the correct password is entered again. For example: if
you change the level to “5”, the DVD player will not play discs
with ratings of “6”, “7” or “8” unless the correct password is
entered on the remote control.
Downloaded From DvDPlayer-Manual.com NAD Manuals
INITIAL SETTINGS
PAGE 21
Selecting Parental Control Rating Levels and Password (Cont’d)
Setting your password (DVD only)
POWER
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
If you change the rating level to “7” or lower, you must enter
a 4-number “password” to prevent playback of discs with
higher ratings.
1
MENU
At the SETUP screen, press
“Password” and press G.
Disc Audio
New
Disc Subtitle
————
E
to select
Disc Menu
1, 2,
3
Rating
Password
SELECT
ENTER
TV Aspect
Menu Language
DISPLAY
Progressive Scan
RETURN
Digital Audio Output
5.1 Speaker Setup
ZOOM
MARKER — SEARCH
Others
SCAN
SKIP
PLAY
2
STOP
NEXT DISC PAUSE/STEP
2, 3
Example : 1234
Do not forget your password.
SLOW
1
2
3
4
5
6
7
8
Input a 4-number password and press
SELECT/ENTER.
3
Input the 4-number password again and press
SELECT/ENTER to verify.
Setting is complete.
CLEAR
9
PROGRAM
0
● The rating is locked. Any disc whose rating is higher than
the setting, cannot be played back unless the correct
password is entered.
To change/clear memorized password
1
To clear your 4-number password
2
If you forget your password, to clear the
current password, follow the procedure below.
At the SETUP screen, press E to select
“Password” and press G.
Input your password and press
SELECT/ENTER.
Disc Audio
Change
Disc Subtitle
Clear
Disc Menu
1
Rating
Press SETUP.
Password
The SETUP menu is displayed.
TV Aspect
Menu Language
2
Progressive Scan
Enter 6-digit number “210499” by
pressing number buttons.
The 4-number password is cleared. “P CLr”
appears on the display.
3
Enter a new password.
Refer to “Setting your password” section on the
right.
Downloaded From DvDPlayer-Manual.com NAD Manuals
Digital Audio Output
5.1 Speaker Setup
Others
3
To change or clear your password, press D/E
to select the “Change” or “Clear” and press
SELECT/ENTER.
To change the rating level/password, follow the steps on
page 20-21 again.
PAGE 22
INITIAL SETTINGS
Selecting TV Aspect
Select the appropriate screen type according to
your TV set; conventional size screen (4:3) or
wide-screen (16:9).
POWER
1
At the SETUP screen, press D/E to select “TV
Aspect” and press G.
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
OPEN/CLOSE
Password
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
TITLE
MENU
5.1 Speaker Setup
Others
1, 2
SELECT
ENTER
DISPLAY
RETURN
ZOOM
2
Press D/E to select the desired Aspect and
press SELECT/ENTER.
MARKER — SEARCH
SCAN
PLAY
SKIP
STOP
NEXT DISC PAUSE/STEP
SLOW
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
Password
TV Aspect
1
2
3
4
5
6
7
8
Menu Language
Progressive Scan
CLEAR
9
PROGRAM
Digital Audio Output
5.1 Speaker Setup
Others
0
4:3 Letterbox : The video material not formatted in the Pan
& Scan style is played back in the letterbox style (black
bands appear at top and bottom of screen).
4:3 Panscan : Select when a conventional TV set is
connected. The video material formatted in the Pan & Scan
style is played back in that style (the left and right edges are
cut off).
16:9 Wide : Select when a wide-screen TV set is connected.
Played in “FULL” size. (Setting the wide-screen TV to “FULL”
mode is also necessary.)
4:3 Letterbox
Cut Off
* Each screen shows an example when the video material
for a wide-screen is played.
(This setting does not affect the video material for
conventional size.)
4:3 Panscan
16:9 Wide
Downloaded From DvDPlayer-Manual.com NAD Manuals
INITIAL SETTINGS
PAGE 23
Selecting Menu Language
Selects language for SETUP menus and displays
on the TV.
POWER
1
At the SETUP screen, press D/E to select
“Menu Language” and press G.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
OPEN/CLOSE
Rating
Password
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TV Aspect
Menu Language
Progressive Scan
TITLE
Digital Audio Output
MENU
5.1 Speaker Setup
Others
1, 2
SELECT
ENTER
DISPLAY
RETURN
ZOOM
2
Press D/E to select the desired Language
and press SELECT/ENTER.
MARKER — SEARCH
SCAN
PLAY
SKIP
STOP
NEXT DISC PAUSE/STEP
SLOW
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
Password
TV Aspect
1
2
3
4
5
6
7
8
9
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
CLEAR
PROGRAM
0
Downloaded From DvDPlayer-Manual.com NAD Manuals
Others
PAGE 24
INITIAL SETTINGS
Selecting Progressive Scan
If your television is high-definition or “digital ready”
television, you may take advantage of the DVD
Player’s progressive scan output for the highest
video resolution possible. Make the component
video connections as shown on page 16 or you
may connect the component video jacks directly to
the component video or HD component inputs on
your TV or monitor. Once the connection is made,
the progressive scan circuitry must be activated by
changing the SETUP menu.
1
At the SETUP screen, press D/E to select
“Progressive Scan” and press G.
Disc Audio
Off
Disc Subtitle
On
Disc Menu
Rating
Password
TV Aspect
Menu Language
Progressive Scan
Note: The progressive scan capability is not
operational with standard analog component video
connections.
Digital Audio Output
5.1 Speaker Setup
Others
2
POWER
Press D/E to select the desired Progressive
mode (On or Off) and press SELECT/ENTER.
OPEN/CLOSE
SETUP
REPEAT
AUDIO
SUBTITLE
A-B
RANDOM
ANGLE
SOUND
Disc Audio
Off
Disc Subtitle
On
Disc Menu
Rating
TITLE
MENU
Password
TV Aspect
Menu Language
1, 2
Progressive Scan
SELECT
ENTER
Digital Audio Output
5.1 Speaker Setup
DISPLAY
RETURN
ZOOM
Others
MARKER — SEARCH
Off:
SCAN
PLAY
SKIP
STOP
On:
NEXT DISC PAUSE/STEP
SLOW
1
2
3
4
5
6
Notes
❍
7
8
CLEAR
9
PROGRAM
If you are using the COMPONENT VIDEO OUT jacks,
but are connecting the DVD player to a standard
(analog) television, set the Progressive mode to “Off”.
If you are using the COMPONENT VIDEO OUT jacks
for connection to a TV that is compatible with a progressive scan signal, set the Progressive mode to
“On”.
The Progressive function only works when VIDEO OUTPUT
SELECT switch on the rear panel is set to COMPONENT/
PROGRESSIVE SCAN.
0
Warning
Once the setting for progressive scan output is entered, an image will
only be visible on a progressive scan compatible video display. If you
change the setting to “On” in error, you must reset the unit by first
pressing the STOP to stop any disc that is playing. Next, press the
STOP again and hold it for five seconds before releasing it. The
video output will be restored to the standard setting, and a picture
will once again be visible on a conventional analog display.
Downloaded From DvDPlayer-Manual.com NAD Manuals
INITIAL SETTINGS
PAGE 25
Selecting Digital Audio Output
Each DVD disc has a variety of audio output
options. Set the player’s Digital Audio Output
according to the type of audio system you use.
1
At the SETUP screen, press D/E to select
Digital Audio Output and press G.
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Rating
Password
POWER
OPEN/CLOSE
Sample Freq.
TV Aspect
48 KHz
Menu Language
96KHz
Progressive Scan
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
Digital Audio Output
5.1 Speaker Setup
TITLE
Others
MENU
2
1, 2
You can select Digital Audio Output or Sampling
Frequency item by pressing SELECT/ENTER.
SELECT
ENTER
DISPLAY
RETURN
ZOOM
■ Digital Audio Output
DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM” if
MARKER — SEARCH
SCAN
PLAY
an active digital output is supplied to a Dolby Digital decoder,
(or an amplifier or other equipment with Dolby Digital
decoder).
SKIP
STOP
NEXT DISC PAUSE/STEP
Stream/PCM: Select “Stream/PCM” if an active
SLOW
1
2
3
digital output is supplied to an amplifier or other
equipment with DTS decoder, Dolby Digital decoder and
MPEG decoder.
4
5
6
PCM: Select “PCM” if an active digital output is
7
8
9
supplied to an amplifier or other equipment with linear PCM
only (or MD recorder or DAT deck).
CLEAR
PROGRAM
0
■
OUTPUT
Playback
Disc
Press D/E to select the desired output and
press SELECT/ENTER.
Stream/PCM
Dolby Digital/
PCM
PCM only
96 kHz
Linear PCM
DVD
PCM
PCM
PCM
DTS DVD
DTS bit Stream
DTS bit Stream
DTS bit Stream
Dolby Digital
DVD
Dolby Digital
bit Stream
Dolby Digital
bit Stream
PCM
MPEG DVD
MPEG bit Stream PCM
PCM
Audio CD
PCM
PCM
PCM
DTS Audio CD
DTS bit Stream
DTS bit Stream
DTS bit Stream
Sampling Frequency
To change the Sample Frequency setting, first select the
desired digital audio output type as indicated above.
If your A/V receiver or surround processor is NOT capable of
handling 96kHz signals, select the 48kHz option. When this
choice is made, this unit will automatically convert any 96kHz
signals to a 48kHz output so that your system is capable of
decoding them.
If your A/V receiver or surround processor is capable of
handling 96kHz signals, select the 96kHz option. When this
choice is made, this unit will pass each type of signal through
without any further processing.
Notes
Downloaded From DvDPlayer-Manual.com NAD Manuals
❍
❍
If an active digital audio output signal is supplied to a receiver or
other equipment without a corresponding digital decoding capability, a very loud noise may be produced which could
permanently damage the speakers.
The DTS DVD disc sound is played back only when the DVD
player is connected to a receiver with a DTS decoder.
PAGE 26
INITIAL SETTINGS
Others
The DRC settings can be changed.
1
At the SETUP screen, press D/E to select
“Others” and press G.
Disc Audio
DRC On
Disc Subtitle
Disc Menu
POWER
OPEN/CLOSE
Rating
Password
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
TITLE
MENU
5.1 Speaker Setup
Others
1, 2
SELECT
ENTER
2
DISPLAY
RETURN
ZOOM
The setting of the selected item are changed between
On and Off.
MARKER — SEARCH
SCAN
PLAY
SKIP
■
SLOW
1
2
3
4
5
6
7
8
CLEAR
9
PROGRAM
0
Notes
❍
❍
About DRC (Dynamic Range Compression)
With the DVD format you have the opportunity to hear a
program’s soundtrack in the most accurate and realistic
presentation possible, thanks to the use of digital audio
technology. However, in certain instances you may wish to
slightly compress the dynamic range of the audio output
(the difference between the loudest sounds and the
quietest ones) so that you may listen to a movie at a lower
volume without losing dialogue intelligibility.
Downloaded From DvDPlayer-Manual.com NAD Manuals
DRC (Dynamic Range Compression) On/Off
On: Select this option to turn on the Dynamic Range
Compression circuitry so that the dialogue remains
clear even at low volume levels.
Off: Select this option to turn off the Dynamic Range
Compression and have the soundtrack presented
exactly as it was created.
STOP
NEXT DISC PAUSE/STEP
Press D/E to select the desired items and
press SELECT/ENTER.
The DRC function works only during playback of Dolby Digital
recorded discs.
The level of Dynamic Range Compression may differ depending
on the DVD disc.
PAGE 27
INITIAL SETTINGS
Table of Languages and Their Abbreviations
Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menu” (See page 19).
Code
Language
Code
Language
Code
Language
Code
Language
6565
Afar
7079
Faroese
7678
Lingala
8375
Slovak
6566
Abkhazian
7082
French
7679
Laothian
8376
Slovenian
6570
Afrikaans
7089
Frisian
7684
Lithuanian
8377
Samoan
6577
Ameharic
7165
Irish
7686
Latvian, Lettish
8378
Shona
6582
Arabic
7168
Scots Gaelic
7771
Malagasy
8379
Somali
6583
Assamese
7176
Galician
7773
Maori
8381
Albanian
6588
Aymara
7178
Guarani
7775
Macedonian
8382
Serbian
6590
Azerbaijani
7185
Gujarati
7776
Malayalam
8385
Sundanese
6665
Bashkir
7265
Hausa
7778
Mongolian
8386
Swedish
6669
Byelorussian
7273
Hindi
7779
Moldavian
8387
Swahili
6671
Bulgarian
7282
Croatian
7782
Marathi
8465
Tamil
6672
Bihari
7285
Hungarian
7783
Malay
8469
Telugu
6678
Bengali; Bangla
7289
Armenian
7784
Maltese
8471
Tajik
6679
Tibetan
7365
Interlingua
7789
Burmese
8472
Thai
6682
Breton
7378
Indonesian
7865
Nauru
8473
Tigrinya
6765
Catalan
7383
Icelandic
7869
Nepali
8475
Turkmen
6779
Corsican
7384
Italian
7876
Dutch
8476
Tagalog
6783
Czech
7387
Hebrew
7879
Norwegian
8479
Tonga
6789
Welsh
7465
Japanese
7982
Oriya
8482
Turkish
6865
Danish
7473
Yiddish
8065
Panjabi
8484
Tatar
6869
German
7487
Javanese
8076
Polish
8487
Twi
6890
Bhutani
7565
Georgian
8083
Pashto, Pushto
8575
Ukrainian
6976
Greek
7575
Kazakh
8084
Portuguese
8582
Urdu
6978
English
7576
Greenlandic
8185
Quechua
8590
Uzbek
6979
Esperanto
7577
Cambodian
8277
Rhaeto-Romance
8673
Vietnamese
6983
Spanish
7578
Kannada
8279
Rumanian
8679
Volapük
6984
Estonian
7579
Korean
8285
Russian
8779
Wolof
6985
Basque
7583
Kashmiri
8365
Sanskrit
8872
Xhosa
7065
Persian
7585
Kurdish
8368
Sindhi
8979
Yoruba
7073
Finnish
7589
Kirghiz
8372
Serbo-Croatian
9072
Chinese
7074
Fiji
7665
Latin
8373
Singhalese
9085
Zulu
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 28
BASIC OPERATIONS
Basic Playback
This section shows you the basics on how to play back a DVD video disc.
Preparations
● When you want to play back DVD video discs, turn on the TV and
select the video input source connected to the DVD player.
● When you want to enjoy the sound of DVD video discs or audio
CDs from the audio system, turn on the audio system and select
the input source connected to the DVD player.
● For connection details, see pages 12 through 17.
● Set the playback picture size according to the aspect ratio of the
connected TV via the SETUP menu (TV Aspect).
● If you do not have the necessary equipment to enjoy Dolby Digital
sound, set the Digital Audio Output (via the SETUP menu) to
“PCM”.
3
1
POWER
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
1
Press POWER.
2
Press OPEN/CLOSE.
●
2, 4
3
MENU
●
●
SELECT
ENTER
DISPLAY
4
MARKER — SEARCH
SCAN
PLAY
SKIP
STOP
NEXT DISC PAUSE/STEP
4
SLOW
1
2
3
4
5
6
7
8
CLEAR
9
PROGRAM
Place a disc on the disc tray with the
playback side down.
There are two different disc sizes. Place the disc in the
correct guide on the disc tray. If the disc is out of the guide,
it may damage the disc and cause the DVD player to
malfunction.
Do not place anything except 3” discs or 5” discs on the disc
tray.
Discs can be loaded one at a time by pressing NEXT DISC to
rotate the carousel.
Caution: Do not touch the loading drawer and carousel
while they are in motion, and do not attempt to rotate
the carousel by hand; doing so could result in incorrect
operation of the player and/or damage to the discs.
RETURN
ZOOM
The disc tray opens.
You can open the disc tray by pressing this button even if the
DVD player is in standby mode.
●
TITLE
The DVD player turns on and the power indicator
lights.
Press OPEN/CLOSE or PLAY to close the
loading drawer.
The disc on the tray 1 is ready to be played back.
Playback may begin automatically depending on the
disc.
If no disc is loaded on disc tray 1, select another disc
by following step 5.
●
●
0
Do not close the loading drawer by hand.
If the disc is placed in upside down (and it is a single-sided
disc), “NO DISC” or “DISC ERROR” appears on the TV
screen.
MP3
HD CD DVD
1
2
3
TITLE
CHP/TRK
PROG.
RANDOM ALL A
B
5
4
Operating status indicator
●
●
Downloaded From DvDPlayer-Manual.com NAD Manuals
If you insert an audio CD, the CD indicator lights up on the
display. The title number does not appear.
After playing back all of the chapters in the title, the DVD player
automatically stops and returns to the menu screen.
BASIC OPERATIONS
PAGE 29
Basic Playback (Cont’d)
5
POWER
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
6
MENU
7
SELECT
ENTER
DISPLAY
Press PLAY to begin playback.
Playback begins.
You can skip this step if the disc is already playing
automatically.
The menu screen appears on the TV screen.
In the case of interactive DVDs with playback, a menu screen appears
on the TV screen. Perform the following steps:
RETURN
ZOOM
MARKER — SEARCH
SCAN
PLAY
SKIP
STOP
5
Also you can select a disc in the DVD player directly
by using the remote control, press NEXT DISC and
then press a number button (1-5) on the remote control
within one second.
OPEN/CLOSE
SETUP
If you want to select another disc, press
NEXT DISC once or more.
NEXT DISC PAUSE/STEP
6
2
3
4
5
6
7
8
Press D/E/F/G and press SELECT/ENTER, or
press the numeric button(s), to select the
desired item.
Playback of the selected item begins.
SLOW
1
CLEAR
7
1
2
OR
3
4
9
PROGRAM
Example of interactive DVD On-Screen Menu
0
●
For further information, refer to the disc jacket of the disc
you are playing.
After operation
When the unit is not in use, remove the disc and press
POWER to turn off the DVD player.
Notes
❍
❍
❍
❍
❍
❍
Downloaded From DvDPlayer-Manual.com NAD Manuals
Do not move the DVD player during playback. Doing so may
damage the disc and the DVD player.
Use the OPEN/CLOSE button on the remote control or DVD
player to open and close the disc tray. Do not push the disc tray
while it is moving. Doing so may cause the DVD player to
malfunction.
Do not push up the disc tray or put any objects other than discs
on the disc tray. Doing so may cause the DVD video
player to malfunction.
Keep your fingers well clear of the disc tray as it is closing. Be
especially careful with children’s fingers around the
closing disc tray as there is a risk of personal injury.
When “
” appears on the TV screen while a button is
pressed, it means that this function is not available on the disc
you are playing.
Depending on the DVD disc, some operations may be different
or restricted. Refer to the jacket or case of the disc you are
playing.
PAGE 30
BASIC OPERATIONS
Basic Playback (Cont’d)
Stopping Play
POWER
Press STOP during playback.
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
Resume Play
● When play is stopped, the unit records the point where
STOP was pressed (RESUME function).
Press PLAY and play will resume from this point.
MENU
Notes
SELECT
ENTER
❍
DISPLAY
❍
RETURN
ZOOM
❍
MARKER — SEARCH
SCAN
PLAY
This operation works only with discs for which the elapsed playing time appears in the DVD display window during stop.
Resume function will be cleared when the STOP is pressed in
the STOP mode.
The Resume function may not be available on some DVD discs.
SKIP
PLAY
Last Scene Memory
STOP
STOP
NEXT DISC PAUSE/STEP
SLOW
1
2
3
4
5
6
7
8
CLEAR
This player memorizes last scene for the last disc you have
watched. Settings remain in memory even if you remove the
disc from the player or switch off the player. If you load a disc
that has its settings memorized, Latest Stop Position is
automatically recalled.
Notes
9
PROGRAM
0
❍
❍
❍
❍
Settings are stored in memory for use any time.
Switching of the audio mode, etc., is automatic on some discs.
This player does not memorize if you switch off the player when
a DVD or title menu appears on the TV screen.
The last scene memory function will be cleared when the STOP
is pressed in the STOP mode.
Screen Saver
The screen saver is useful to prevent your display from becoming damaged.
The screen saver picture appears when you leave the DVD
player in stop mode for about 5 minutes.
Automatic power off function
After the Screen Saver has been engaged for about 5 minutes,
the DVD player will automatically turn itself off.
Screen Saver
Downloaded From DvDPlayer-Manual.com NAD Manuals
BASIC OPERATIONS
PAGE 31
Basic Playback (Cont’d)
Skipping Discs
Press NEXT DISC during playback or in the stop mode.
● Each time the button is pressed, the next disc tray is
selected.
DVD
1
2
3
TITLE
CHP/TRK
5
4
NEXT DISC
1
2
3
5
4
Notes
POWER
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
❍
When the NEXT DISC is pressed during playback or in the stop
mode, the disc tray advances to the next disc.
❍
If there is no disc on the selected disc tray, the disc tray of the
next number will be selected.
OPEN/
CLOSE
Exchanging the Disc and Starting Playback
TITLE
MENU
1
Press OPEN/CLOSE during playback or in the
stop mode.
Play is stopped (if pressed during playback), the
loading drawer opens and the disc tray which was in
the play position comes to the center position.
SELECT
ENTER
DISPLAY
RETURN
ZOOM
2
MARKER — SEARCH
SCAN
PLAY
Exchange the disc in the center position.
SKIP
PLAY
STOP
Center position
NEXT DISC PAUSE/STEP
SLOW
NEXT DISC
1
2
3
4
5
6
7
8
CLEAR
9
PROGRAM
0
Downloaded From DvDPlayer-Manual.com NAD Manuals
3
Press OPEN/CLOSE or PLAY again.
The loading drawer closes, the disc tray returns to the
play position and playback begins from the new disc.
PAGE 32
BASIC OPERATIONS
Special Playback
Still Picture (Pause)
POWER
Press PAUSE/STEP during playback.
OPEN/CLOSE
●
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
DVD
The player will be placed in the still picture mode.
● CD
The player will be placed in the pause mode.
MENU
Frame Advance (DVD only)
Press PAUSE/STEP during still playback.
SELECT
ENTER
DISPLAY
(Each time you press PAUSE/STEP, the picture advances
one frame)
RETURN
To resume normal playback, press PLAY.
ZOOM
MARKER — SEARCH
SCAN
PLAY
Skipping chapters and tracks
forward or back
SKIP
PLAY
STOP
STOP
NEXT DISC PAUSE/STEP
PAUSE/
STEP
SLOW
1
2
3
4
5
6
7
8
9
CLEAR
SKIP
(
/
)
PROGRAM
0
Skipping forward
Press SKIP
during playback.
A chapter (DVD) or a track (CD) is skipped each time the
button is pressed.
Skipping back
Press SKIP
during playback.
● When the button is pressed once midway through a
chapter/track, the player returns to the start of that
chapter/track. When it is pressed again, a chapter/track is
skipped each time the button is pressed.
HDCD Playback
How To Set The Video Mode
● With certain DVD disc, the playback picture is
flickering or Dot Crawl is shown on straight
lines. That means Vertical interpolation or
De-interlace is not perfectly matched with DVD
disc. In that case, the picture quality can be
improved with changing video mode.
● To change the video mode, press and hold
DISPLAY button on the remote control about
3 seconds during playback of DVD disc.
Changed video mode number is displayed on
the TV screen. Check whether video quality is
improved. You can repeat above procedure until
desired picture quality appears.
● Procedure of video mode is changed;
MODE2 → MODE3 → MODE4 → MODE5 →
MODE1.
● If you turn off the the power, the video mode will
be back to initial state (Auto).
Downloaded From DvDPlayer-Manual.com NAD Manuals
HDCD is a process that increases the fidelity of both specially encoded HDCD discs and standard CD audio discs. When
an HDCD-encoded disc is playing, the special decoder is
automatically activated and the HDCD Indicator lights. No
user intervention is required.
To enjoy the benefits of HDCD, your DVD Player must be
connected to your A/V receiver via the Analog Audio Outputs.
However, if your A/V receiver or surround processor is
equipped with built-in HDCD decoding, you may also use
a Coaxial or Optical digital audio connection so that the
HDCD processing is done there.
BASIC OPERATIONS
PAGE 33
Special Playback (Cont’d)
You can play back discs at various speeds.
To Scan at fast forward or fast
reverse playback.
Press the SCAN
POWER
or
[TV screen]
OPEN/CLOSE
FF X2
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
SELECT
ENTER
RETURN
ZOOM
MARKER — SEARCH
SCAN
SCAN
(
/
PLAY
NEXT DISC PAUSE/STEP
To return to normal playback, press PLAY.
SKIP
PLAY
STOP
)
GG X2
● The speed of advance (reverse) is relatively slow at first.
When the button is pressed again, the speed becomes
faster. (Each time the button is pressed, the speed
increases up to 4 steps (DVD) or 3 steps (CD).)
● The speed will be retained even after the button is
released.
MENU
DISPLAY
button during playback.
Note
❍
SLOW
SLOW
(F V / V G)
1
2
3
4
5
6
7
8
CLEAR
The DVD player does not play back sound during the high
speed reverse and forward playback of DVD video discs.
However, the DVD player plays back sound during fast forward
or fast reverse playback of audio CDs.
Playing in slow-motion (DVD only)
9
PROGRAM
0
Press SLOW
F V or V G during playback.
The playback speed becomes 1/16 of the normal speed.
[TV screen]
F V 1/16
V G 1/16
● The speed of slow-motion is slow at first. When the button
is pressed again, the speed becomes faster. (Each time
the button is pressed, the speed increase up to 4 steps.
● The speed will be retained even after the button is
released.
To return to normal playback, press PLAY.
Notes
❍
❍
❍
Downloaded From DvDPlayer-Manual.com NAD Manuals
The sound is muted during slow-motion playback.
Subtitles do not appear on the screen during slow motion
playback.
The SLOW buttons do not work with Audio CDs.
PAGE 34
OPERATION USING GRAPHICAL USER INTERFACE (GUI) MENU ICONS
General Information about GUI menu icons
This unit features GUI Menu Icons showing disc
information (title/chapter/track number, elapsed playing
time, audio/subtitle language, angle, and sound) and
player information (repeat play, play mode, marker,
etc.). Some icons only show the indicated information.
Other icons allow the settings to be changed.
Common procedures
1
● Title function can be accessed from the stop mode.
2
POWER
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
1
3
MENU
2, 3
SELECT
ENTER
DISPLAY
RETURN
ZOOM
Press D/E to select the desired item.
● The current selected item is indicated by a yellow
frame on its GUI menu icons.
OPEN/CLOSE
SETUP
Press DISPLAY during playback.
Press F/G to select the desired setting.
● When numbers are displayed (e.g. title number),
the numeric buttons can also be used for setting
instead of F/G.
● For some functions, the setting will be registered
immediately; for others, SELECT/ENTER must be
pressed.
MARKER — SEARCH
SCAN
PLAY
SKIP
To clear the GUI Menu Icons, press DISPLAY
again.
STOP
NEXT DISC PAUSE/STEP
SLOW
Examples of GUI Menu Icons.
(The screens may differ depending on the disc contents.)
1
1
1/9
0:16:57
1 ENG
D
6 CH
1
OFF
0:16:57
1
STER.
NORM.
NORM.
(DVD GUI)
Downloaded From DvDPlayer-Manual.com NAD Manuals
CHAPT
(CD GUI)
A
B
OFF
(DVD or CD GUI)
OPERATION USING GRAPHICAL USER INTERFACE (GUI) MENU ICONS
PAGE 35
Detailed description of each GUI menu icon
You can view information about a disc and its operational status on the TV screen.
Press DISPLAY during
playback.
[TV screen] DVD GUI
1
1
0:16:57
1 ENG
D
6 CH
OFF
1
NORM.
Press DISPLAY during
playback.
[TV screen] CD GUI
FUNCTION
(Press D/E to select desired item)
To show the current title number
and to jump to the desired title number
To show the current chapter number
and to jump to the desired chapter number
To show the elapsed time
and directly select scenes by the desired time.
To show the current audio soundtrack language,
encoding method, channel number
and to change the settings.
To show the current subtitles language
and to change the setting.
F/G, or
Numeric
SELECT/ENTER
F/G, or Numeric
SELECT/ENTER
SKIP
Numeric
SELECT/ENTER
F/G,
AUDIO
F/G,
SUBTITLE
To show the current angle number
and to change the angle.
F/G,
ANGLE
To show the current sound (NORMAL or 3D SURROUND)
and to change the setting.
F/G,
SOUND
FUNCTION
(Press D/E to select desired item)
To show the current track number
1
SELECTION
METHOD
and to jump to the desired track number
SELECTION
METHOD
F/G, or Numeric
SELECT/ENTER
SKIP
To show the elapsed time.
0:16:57
(Display only)
To show the current audio (STEREO, LEFT, RIGHT)
STER.
NORM.
and to select to the desired audio channel.
To show the current sound (NORMAL or 3D SURROUND)
and to change the setting.
Note
❍
Some DVD discs may not provide all of the above GUI menu icons.
Downloaded From DvDPlayer-Manual.com NAD Manuals
F/G,
AUDIO
F/G,
SOUND
PAGE 36
ADVANCED OPERATION
Using a title menu
Some movie discs may contain two or more
titles. If the disc has a title menu recorded on it,
the TITLE button can be used to select the
movie title. (The details of operation differ
depending on the disc used.)
● Selecting a title may not be possible on
certain DVD discs.
1
TITLE
1
2
DISPLAY
RETURN
ZOOM
2
MARKER — SEARCH
SCAN
SKIP
PLAY
Press D/E/F/G and press SELECT/ENTER or
PLAY, or press the numeric button(s), to
select desired title.
2
STOP
NEXT DISC PAUSE/STEP
A list of the titles on the disc is displayed.
Pressing TITLE again to resume play from the scene
when TITLE was first pressed.
• Resume play may not be possible on certain discs.
MENU
SELECT
ENTER
Press TITLE.
SLOW
The selected title now starts playing.
Using a DVD menu
Some DVDs have unique menu structures called
DVD menus. For example, DVDs programmed
with complex contents provide guide menus, and
those recorded with various languages provide
menus for audio and subtitle language. Although
the DVD menu’s contents and operation differ
from disc to disc, the following explains the basic
operation when this feature is used.
TITLE
MENU
SELECT
ENTER
DISPLAY
1
3
4
1
2
MARKER — SEARCH
SCAN
PLAY
Pressing MENU again resumes play from the scene
when MENU was first pressed.
• Resume play may not be possible on certain discs.
2
SKIP
STOP
NEXT DISC PAUSE/STEP
Press D/E/F/G and press SELECT/ENTER,
or press the numeric button(s), to select
desired item.
SLOW
1
2
3
4
5
6
7
8
CLEAR
The DVD menu available on the disc is now displayed.
1
2
RETURN
ZOOM
Press MENU during play.
9
PROGRAM
0
Downloaded From DvDPlayer-Manual.com NAD Manuals
The selected item is now executed.
ADVANCED OPERATION
PAGE 37
Changing subtitle language
It is possible to change the subtitle language to a
different language from the one selected at the initial
settings. (See page 19 for further info.)
This operation works only with discs on which multiple
subtitle languages are recorded.
1, 2
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
1
MENU
❍
❍
In some cases, the subtitle language is not changed to
the selected one immediately.
When a disc supporting the closed caption is played, the
subtitle and the closed caption may overlap each other
on the TV screen. In this case, turn the subtitle off.
When the desired language is not selected even after
pressing the button several times, it means that the
language is not available on the disc.
When the power is turned on or the disc is removed,
subtitles appears in the language selected at the initial
settings. If this language is not recorded on the disc, the
disc’s priority language appears.
Press SUBTITLE repeatedly until the
desired language is selected.
Number of the subtitle language being played
back is shown.
Notes
❍
When no subtitles are recorded, “OFF” will be
displayed instead of the language number.
OFF
2
❍
Press SUBTITLE during playback.
1 ENG
To eliminate the On Screen Subtitles.
Press SUBTITLE repeatedly to select OFF at step 2.
Changing audio soundtrack language
It is possible to change the audio soundtrack language
(or encoding method, channel number) to a different
language from the one selected at the initial settings in
case of DVD disc. (See page 19 for further info.) This
operation works only with discs on which multiple
audio soundtrack languages are recorded.
And it is possible to change the audio channel in case
of audio CD.
• DVD
Press AUDIO during play.
1
1 ENG
D
6 CH
2
1, 2
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
Number of the audio soundtrack language being
played back.
Press AUDIO repeatedly until the desired
language (or encoding method, channel
number) is selected.
2 FRE
D
6 CH
MENU
• CD
Notes
❍
❍
❍
When the desired language is not selected even after
pressing the button several times, it means that the
language is not available on the disc.
When the power is turned on or the disc is removed, the
language heard is the one selected at the initial settings.
If this language is not recorded on the disc, only the
available language on the disc will be heard.
Some discs may not respond to Audio feature.
Downloaded From DvDPlayer-Manual.com NAD Manuals
1
Press AUDIO during play.
STER.
2
Press AUDIO repeatedly until the desired
sound is selected.
LEFT
PAGE 38
ADVANCED OPERATION
Viewing from another angle
Some DVDs may contain scenes which have been
shot simultaneously from a number of different angles.
For these discs, the same scene can be viewed from
each of these different angles using the ANGLE button.
(The recorded angles differ depending on the disc
used.)
1
Number of angle
being played back.
2
1
2
Press ANGLE during playback.
3
1
Press ANGLE repeatedly until the
desired angle is selected.
2
POWER
For your reference
• The ANGLE indicator will blink in the DVD display window at scenes recorded at different angles to indicate
that angle switching is possible.
• The angle number can be programmed beforehand; the
angle will be switched to the selected number when the
ANGLE indicator blinks.
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
1, 2
MENU
Note
This function only works for discs having scenes recorded
at different angles.
❍
Producing a 3D SURROUND effect
This unit can produce a 3D Surround effect, using 3D
Surround Sound technology, which simulates multi-channel audio playback from two conventional stereo speakers instead of the five or more speakers normally
required to listen to multi-channel audio from a home
theater. This feature works with DVD discs encoded with
Dolby Pro Logic and Dolby Digital audio tracks.
1
Press SOUND during playback.
Each time this button is pressed, the TV screen
display changes.
NORM.
2
Press SOUND repeatedly until the
desired sound is selected.
3D SUR
POWER
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
MENU
1, 2
Notes
❍
❍
SELECT
ENTER
❍
DISPLAY
RETURN
Downloaded From DvDPlayer-Manual.com NAD Manuals
This 3D Surround effect may not be available on some
DVD discs or audio CD, such as those recorded with a
mono audio soundtrack.
Turn off the TV surround sound and other surround
effects when using this 3D surround effect.
For best 3D Surround effect using only two speakers it is
recommended that the two speakers be positioned
approximately 8’ to 10’ apart, and the listening
position should be 8’ to 10’ away from the speakers.
PAGE 39
ADVANCED OPERATION
Repeat Play
Repeating viewing (listening)
Repeating sections between two
specific points (A-B repeat)
Press REPEAT during playback.
Each time this button is pressed, the TV screen
changes as shown below and the disc will repeat a
chapter or title (DVD) or a track (CD).
1
Press A-B during play at the point where
repeat play is to start (A).
A
• DVD
Repeat of
chapter being
played
• You can select “OFF” at this step by pressing
CLEAR.
CHAPT
Repeat of title
being played
*
2
TITLE
Press A-B during play at the point where
repeat play is to be concluded (B).
OFF
Cancel repeat mode
(normal play)
A
Repeat play of the selection between points A
and B starts.
• CD
Repeat of track
being played
B
TRACK
Repeat of entire
current disc contents
To return to normal play
DISC
Press A-B once “OFF” is displayed.
Repeat of entire
all disc contents
ALL
OFF
Cancels repeat mode
(normal play)
OFF
Notes
❍
To enjoy program repeat play (CD)
If REPEAT is pressed during program play, repeat play
is operated as below.
Repeat of the
current programmed
track
❍
❍
❍
TRACK
ALL
Repeat of all programs
OFF
Cancel repeat mode
(Program play)
To return to normal play
Press REPEAT several times until “OFF” is displayed.
Downloaded From DvDPlayer-Manual.com NAD Manuals
Repeat play works only with discs for which the elapsed
playing time appears in the DVD display window during
playback.
Repeat play may not work correctly with some DVDs.
A-B repeat play works only within a title DVD or a track
CD.
Some subtitles recorded around point A or B may fail to
appear (DVD).
PAGE 40
ADVANCED OPERATION
Storing markers in memory to be viewed (listened to) again
Storing a MARKER in the DVD memory is similar
to marking your page in a book. It allows you to
quickly return to any point on the disc.
Storing a marker in the memory
1
Press MARKER during play at the starting
point to be viewed (listened to) again.
1/9
Indicates “1/9” is stored in the memory.
Up to 9 marks can be stored in the memory.
POWER
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
2
MENU
3
The MARKER SEARCH menu will appear on the TV
screen.
MARKER SEARCH
1 2 3 4 5 6 7 8 9
RETURN
ZOOM
MARKER — SEARCH
SCAN
PLAY
SKIP
2
STOP
NEXT DISC PAUSE/STEP
SLOW
1
2
3
4
5
6
7
4
Press SEARCH during playback.
4
SELECT
ENTER
DISPLAY
1
Recalling/Clearing a marker
OPEN/CLOSE
8
CLEAR
9
PROGRAM
0
Downloaded From DvDPlayer-Manual.com NAD Manuals
3
Press F/G to select the marker to be
recalled/cleared.
4
Press SELECT/ENTER to recall a marker.
Or press CLEAR to clear a marker.
Play resumes from the point corresponding to the
selected marker, or the selected marker is cleared.
Notes
❍ These operations work only with discs for which the elapsed
playing time appears in the DVD display window during playback
or stop.
❍ Some subtitles recorded around the marker may fail to appear
(DVD).
❍ All the markers are cleared when the power is turned off or the
disc is removed.
❍ The marker is not stored when the DVD or title menu is
displayed on the TV screen.
ADVANCED OPERATION
PAGE 41
Zoom Feature
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
TITLE
2
DISPLAY
RETURN
ZOOM
2
Press D/E/F/G buttons to move through
the zoomed picture.
3
Press CLEAR to resume normal playback.
MARKER — SEARCH
SCAN
SKIP
PLAY
Notes
Some discs may not respond to the Zoom feature.
Zoom does not work on subtitles or menus included on
DVD video discs.
❍
❍
1
2
3
4
5
6
7
8
CLEAR
3
Press ZOOM during playback or still
playback to activate the Zoom function.
If you further press ZOOM repeatedly, the magnification
level increases (6 steps).
MENU
SELECT
ENTER
1
1
9
PROGRAM
0
Random Play
Note: This function only works with audio CD discs.
Random does not work with DVD movies.
Random play (CD only)
1
You can playback titles or tracks in random order.
(Random playback)
Press RANDOM repeatedly until desired
random mode is selected during
playback or stop mode.
The unit automatically begins Random Playback
and RANDOM (1-3) appears on the TV screen.
• RANDOM1: Plays all the tracks on a single disc in
random order and then stops.
POWER
• RANDOM2: Plays all the tracks on current disc in
random order and then plays all the tracks on each
succeeding disc in random order and then stops.
OPEN/CLOSE
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
1, 2
• RANDOM3: Plays 2 tracks randomly from a disc and
then plays 2 tracks randomly from a different disc
until all tracks on all discs have been played.
2
To return to normal playback, press
RANDOM repeatedly until NORMAL
appears on the TV screen.
The RANDOM indicator in the DVD display
window disappears.
Notes
❍
Random playback may not be possible on certain discs.
❍
If you press the SKIP
or
button during random
playback, the DVD player goes to another track
randomly and starts playback.
Random playback may not be possible on MP3 encoded
discs.
❍
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 42
ADVANCED OPERATION
Program play
The player plays the tracks on the disc in the
order you specify.
1
Note: Program play function is possible only
with audio CDs. It does not work with DVD
movie discs.
Press PROGRAM in the stop mode.
The program playback screen appears on the TV
screen.
Program
Step
1
1
Clear All
POWER
OPEN/CLOSE
• To exit the screen, press PROGRAM or RETURN.
SETUP
REPEAT
A-B
RANDOM
AUDIO
SUBTITLE
ANGLE
SOUND
TITLE
Enter the disc number using the numerical
keys (1-5) and then press SELECT/ENTER.
3
Enter the track number using the numerical
keys (0-9) and then press SELECT/ENTER.
MENU
2, 3
The next area is selected.
SELECT
ENTER
DISPLAY
RETURN
ZOOM
5
2
4
Repeat steps 2 to 3.
5
Press PLAY to exit the screen.
Up to 20 tracks can be programmed.
MARKER — SEARCH
SCAN
PLAY
SKIP
STOP
NEXT DISC PAUSE/STEP
SLOW
The selected tracks are stored in the player memory
and playback begins with the first programmed
sequence.
After playback of all tracks programmed
2, 3
1
2
3
4
5
6
7
8
9
Play is stopped.
Clearing the program
CLEAR
PROGRAM
0
1
●
To clear the programmed tracks one by one
Press D/E/F/G to select the unwanted number and then
press CLEAR.
●
To clear all the programmed tracks
Press D/E/F/G to select “Clear All” and then press
SELECT/ENTER. Press PROGRAM or RETURN to exit the
screen. (The programs are also cleared when the power is
turned off or the disc is removed.)
Downloaded From DvDPlayer-Manual.com NAD Manuals
ADVANCED OPERATION
PAGE 43
Playback with MP3
To play an MP3 file
2
1
SELECT
ENTER
DISPLAY
Load an MP3 disc.
The MP3 menu is displayed.
RETURN
MP3
Program
MP3-1
ZOOM
MARKER — SEARCH
TRACK 1.mp3
TRACK 2.mp3
2
SCAN
SKIP
PLAY
TRACK 3.mp3
TRACK 4.mp3
STOP
TRACK 5.mp3
TRACK 6.mp3
TRACK 7.mp3
TRACK 8.mp3
To play an MP3 file repeatedly
TRACK 9.mp3
Clear All
● If you press REPEAT once during play, the
current MP3 file will play repeatedly.
● If you press REPEAT twice during play, all
MP3 files on the disc will play repeatedly.
● If you press REPEAT three times, repeat play
will be cancelled.
MP3
MP3-1
Prog
MP3
Progr
MP3-1
2
Press D/E button to select the desired MP3
file and then press PLAY to start playback of
the file.
MP3
Program
MP3-1
TRACK 1.mp3
TRACK 1.mp3
TRACK 1.mp3
TRACK 2.mp3
TRACK 2.mp3
TRACK 2.mp3
TRACK 3.mp3
TRACK 3.mp3
TRACK 3.mp3
TRACK 4.mp3
TRACK 4.mp3
TRACK 4.mp3
TRACK 5.mp3
TRACK 5.mp3
TRACK 5.mp3
TRACK 6.mp3
TRACK 6.mp3
TRACK 6.mp3
TRACK 7.mp3
TRACK 7.mp3
TRACK 7.mp3
TRACK 8.mp3
TRACK 8.mp3
TRACK 9.mp3
TRACK 9.mp3
TRACK 8.mp3
TRACK 9.mp3
Clear All
REPEAT symbol
Notes
❍ The file name is only displayed in English.
❍ If there is an impossible code to display, it will be
displayed underlined (_) instead of English.
❍ This unit can play up to 200 files per disc. A disc
recorded with more than 200 files cannot be played.
❍ Disc format is compatible with ISO9660 only.
❍ If you record MP3 files using the software which cannot
create a FILE SYSTEM, for example “Direct-CD” etc., it
is impossible to playback MP3 files. We therefore
recommend that you use “Easy-CD Creator”, which
creates an ISO9660 file system.
❍ A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it cannot
playback MP3 files. If you wish to playback MP3 files,
format all the data in the disc or use a new one.
❍ If there are already data files which are not MP3 files
on the CD-R disc, please, do not use that disc; use a
new one instead. However, if the disc is a CD-RW disc,
this does not apply.
❍ Direct access to individual tracks may not work with
MP3 encoded discs.
Downloaded From DvDPlayer-Manual.com NAD Manuals
For your reference
• Press SKIP
or SKIP
to play the next file or previous
file during playback.
• Press DISPLAY to move to the next page.
• Press PAUSE/STEP to enter the pause mode, press PLAY or
PAUSE/STEP again to return to normal playback.
• Press STOP to stop the playback.
PAGE 44
ADVANCED OPERATION
Playback with MP3 (Cont’d)
To program play an MP3 file
4
SELECT
ENTER
DISPLAY
RETURN
ZOOM
Load an MP3 disc.
2
Press STOP to stop playback.
3
Press PROGRAM to enter the Program Edition
mode in the stop mode.
MARKER — SEARCH
SCAN
5
1
SKIP
PLAY
STOP
NEXT DISC PAUSE/STEP
1
2
3
4
5
6
7
8
CLEAR
The E mark appears on the right of the word Program
on the right side of MP3 menu.
Press RETURN to exit the Program Edition mode, the
E mark will disappear.
2
SLOW
4
9
PROGRAM
Press D/E to select the desired MP3 file and
then press SELECT/ENTER to add the MP3
file to the program list.
• Repeat step 4 to select another track.
• Up to 60 files can be programmed.
3
0
The MP3 menu is displayed.
MP3
MP3-1
Program
To play an MP3 file repeatedly
TRACK 1.mp3
TRACK 7.mp3
● If you press REPEAT button once during play,
TRACK 2.mp3
TRACK 6.mp3
TRACK 3.mp3
TRACK 9.mp3
the current MP3 file will play repeatedly.
● If you press REPEAT button twice during play,
all MP3 files on the program list will play
repeatedly.
● If you press REPEAT button three times,
repeat play will be cancelled.
Program
Program
TRACK 2.mp3
TRACK 2.mp3
TRACK 7.mp3
TRACK 7.mp3
TRACK 6.mp3
TRACK 6.mp3
TRACK 9.mp3
TRACK 9.mp3
TRACK 4.mp3
TRACK 5.mp3
TRACK 6.mp3
TRACK 7.mp3
TRACK 8.mp3
TRACK 9.mp3
5
Clear All
Press PLAY to play.
The playback now begins in the programmed
sequence.
MP3
MP3-1
Clear All
E
TRACK 2.mp3
Program
TRACK 2.mp3
TRACK 1.mp3
TRACK 7.mp3
TRACK 2.mp3
TRACK 6.mp3
TRACK 3.mp3
TRACK 9.mp3
TRACK 4.mp3
Clear All
TRACK 5.mp3
TRACK 6.mp3
TRACK 7.mp3
TRACK 8.mp3
REPEAT symbol
Clearing the program
●
Clear All
If you want to enter the main menu, press F button.
To clear the program one by one
In the Program Edition mode, press D/E/F/G to
select the unwanted MP3 file on the program list
and then press CLEAR.
●
TRACK 9.mp3
To clear all the programs
In the Program Edition mode, press D/E/F/G to
select the “Clear All” and press SELECT/ENTER.
Downloaded From DvDPlayer-Manual.com NAD Manuals
After playback of all tracks programmed
Play is stopped.
REFERENCE
PAGE 45
Disc Requirements/Copyright Information
Playable Discs
This DVD player can play back the following discs.
Disc mark
Contents
Disc size
12 cm
DVD video discs
Audio+Video
(moving pictures)
Maximum playback time
Approx. 4 hours (single sided disc)
Approx. 8 hours (double sided disc)
8 cm
Approx. 80 minutes (single sided disc)
Approx. 160 minutes (double sided disc)
Audio CDs
Audio
12 cm
74 minutes
8 cm
20 minutes
In addition, this unit can play back a CD-R or CD-RW that contains audio titles or MP3 files. And this unit
can play back a HDCD also.
You cannot playback discs other than those listed above. (Video CD, CD-ROM, CD-Extra, CD-G, photo CD, and
CD-i discs can not be played on this DVD player.)
, HDCD®, High Definition Compatible Digital® and Pacific Microsonics™ are either registered trademarks or
trademarks of Pacific Microsonics, Inc., in the United States and/or other countries. HDCD system manufactured
under license from Pacific Microsonics, Inc. This product is covered by one or more of the following: In the USA:
5,479,168; 5,638,074; 5,640,161; 5,808,574; 5,838,274; 5,854,600; 5,864,311; 5,872,531; and in Australia: 669114.
Other patents pending.
Region Management Information
Region Management Information: This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DVD player, this DVD player cannot play that disc.
The Region number of this DVD player is 1.
1
Notes on Unauthorized Discs
You may not be able to play back some DVD video discs on this player if they were purchased from outside your
geographic area or made for business purposes.
When you try to play back an unauthorized disc, “Check Regional Code” appears on the TV screen.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material
without permission.
DVD video discs are copy protected, and any recordings made from these discs will be distorted.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Downloaded From DvDPlayer-Manual.com NAD Manuals
PAGE 46
REFERENCE
Before Calling Service Personnel
Symptoms and Correction
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD player does
not work.
• No disc is inserted.
• Insert a disc. (Check that the DVD or,
audio CD indicator in the DVD display is
lit.)
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the DVD
player appears on the TV screen.
• The video cable is not connected
securely.
• Connect the video cable into the jacks
securely.
• The connected TV power is turned off.
• Turn on the TV.
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
• The audio cables are not connected
securely.
• Connect the audio cable into the jacks
securely.
• The power of the equipment connected
with the audio cable is turned off.
• Turn on the equipment connected with
the audio cable.
• The Digital Audio Output is set to the
wrong position.
• Set the Digital Audio Output to the
correct position, then turn on the DVD
player again by pressing the POWER
button.
The playback picture is poor.
• The disc is dirty.
• Clean the disc.
The DVD player does
not start playback.
• No disc is inserted.
• Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display is
lit.)
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type, color system and Regional code.)
• The disc is placed upside down.
• Place the disc with the playback side
down.
• The disc is not placed within the guide.
• Place the disc on the disc tray correctly
inside the guide.
• The disc is dirty.
• Clean the disc.
• A menu is on the TV screen.
• Press the SETUP button to turn off the
menu screen.
• The Rating level is set.
• Cancel the Rating function or change
the rating level.
• The remote control is not pointed at the
remote sensor of the DVD player.
• Point the remote control at the remote
sensor of the DVD player.
• The remote control is too far from the
DVD player.
• Operate the remote control within about
23 ft (7 m).
• There is an obstacle in the path of the
remote control and the DVD player.
• Remove the obstacle.
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
No sound.
The remote control
does not work properly.
Downloaded From DvDPlayer-Manual.com NAD Manuals
REFERENCE
PAGE 47
Specifications
[DVD player]
DVD player/Outputs/Supplied Accessories
Power supply
AC 120V, 60 Hz
Power consumption
16 W
Weight
12.6 lbs (5.7 kg)
External dimensions (W X H X D)
17” X 4.7” X 16.2” (430 x 118 x 411 mm)
Signal system
NTSC
Laser
Semiconductor laser, wavelength 650 nm (DVD), 780 nm (CD)
Frequency range (audio)
4 Hz to 20 kHz
Signal-to-noise ratio (audio)
More than 95 dB (EIAJ)
Dynamic range (audio)
More than 90 dB (EIAJ)
Harmonic distortion (audio)
0.008 %
Operating conditions
Temperature: 41°F to 95°F, Operation status: Horizontal
Video output
1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1
S-video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1
[Supplied
Accessories]
[Outputs]
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω
Audio output (digital audio)
0.5 V (p-p), 75 Ω, RCA jack x 1
Audio output (optical audio)
Optical connector x 1
Audio output (analog audio)
1.0 Vrms(1 KHz, -6 dB), 330 Ω, RCA jack (L, R) x 1
●
Video cable ................................................................................................1
●
Audio cable ................................................................................................1
●
Remote control...........................................................................................1
●
Batteries .....................................................................................................2
❋ Designs and specifications are subject to change without notice.
Downloaded From DvDPlayer-Manual.com NAD Manuals
P/NO: 3834RS0023W
Downloaded From DvDPlayer-Manual.com NAD Manuals
Printed in Korea
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement