Bang & Olufsen UG4 Operating And Maintenance Instructions
Bang & Olufsen DVD 1 is designed to offer you the best possible DVD experience. It can play DVDs, audio CDs, and other disc formats. The DVD 1 connects to your Bang & Olufsen TV via a 21-pin AV cable, or to other TVs using separate cables for video, audio and control signals. The DVD 1 also features a stylish close-up operation panel that allows you to control playback and view the elapsed playing time.
Advertisement
Advertisement
DVD 1
Guide
CAUTION: To reduce the risk of electric shock, do not remove cover (or back).
No User-serviceable parts inside.
Refer servicing to qualified service personnel.
WARNING: To prevent fi re or electric shock, do not expose this appliance to rain or moisture. Do not expose this equipment to dripping or splashing and ensure that no objects fi lled with liquids, such as vases, are placed on the equipment.
To completely disconnect this equipment from the AC Mains, disconnect the power supply cord plug from the
AC receptacle.
This symbol indicates that a dangerous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
For the US market only:
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm ful interference to radio communications. How ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
– Consult the retailer or an experienced radio/TV technician for help
For the Canadian market only:
CAUTION: To prevent electric shock do not use the polarized plug, attached to this apparatus, with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.
This class B digital apparatus meets all require ments of the Canadian Interference-Causing Equipment
Regulations.
Contents
Set up DVD 1, 4
Find out how to handle, place and set up your product. This chapter also contains an overview of the socket panel.
Introducing DVD 1, 8
Find out how to use the Beo4 remote control and the close-up operation panel.
Daily use, 10
Find out all there is to know about the daily use of your product, including how to play, cue and wind through a DVD, pause and stop playback, change chapters and play an audio CD.
Preference settings, 12
Find out how to enter or change, for example, settings for language, picture, sound and Parental Control.
On-screen menus, 14
Overview of the on-screen menus.
Maintenance, 18
Index, 20
3
4
Set up DVD 1
Follow the guidelines and procedures on these pages when setting your
DVD 1 up for the first time.
DVD 1 placement guidelines
Place DVD 1 on a solid, level surface. Do not place any items on top of DVD 1.
Place DVD 1 away from radiators and direct sunlight.
Do not place DVD 1 on a carpeted surface, as carpet blocks the ventilation holes in the base.
DVD 1 is intended for indoor use in dry, domestic environments only, with a tempera ture range of 10–35°C (50–95°F).
Condensation can occur if DVD 1 is moved from cold to warm surroundings. This may interrupt playback. Before using DVD 1, let the player stand someplace warm for one to two hours, until the moisture evaporates.
To ensure proper ventilation, allow for at least 5 centimetres (2") of space at the sides of DVD 1 and 10 centimetres (4") above it.
Connect DVD 1 to your television
DVD 1 is constructed for connection to a Bang &
Olufsen television via a 21-pin AV cable, but other cables are used in some countries. If
21-pin AV cables are not used in your country, then you can follow the procedure described below to connect DVD 1 to your Bang &
Olufsen television. For an overview of the
DVD 1 socket panel, please refer to page 6.
To the mains To TV To the mains To TV
Register all equipment connected to your TV system, including DVD 1. This is done via your television’s
‘Setup’ menu. Refer to the User’s Guide included with your Bang & Olufsen television to ensure proper connection and registration of extra equipment.
Connection using a 21-pin AV cable…
> Connect the socket marked AV on DVD 1 to the socket marked AV on your television via the
21-pin AV cable.
> If your television is equipped with a built-in
Dolby Digital module, connect the socket marked
DIGITAL OUTPUT on DVD 1 to the INPUT 1 socket on your television. If the required cable is not enclosed, it is available from your Bang & Olufsen retailer.
> Set the switch marked Y/C-RGB-CVBS on the rear of DVD 1 to the correct position:
CVBS
This switch setting is used when you connect
DVD 1 to an AV 9000, BeoVision LX,
BeoVision MS, or BeoVision MX 4000/4002/
6000/7000 television.
Y/C
This switch setting is used when you connect
DVD 1 to a BeoVision Avant 50 Hz television.
RGB
This switch setting is used when you connect
DVD 1 to any other Bang & Olufsen television.
> Finally, connect your DVD 1 to the mains with the enclosed cable. Your DVD 1 is now in stand-by mode – indicated by the red light in the display panel.
Connection without a 21-pin AV cable…
Follow the procedure below to connect your DVD 1 to your Bang & Olufsen television:
> Connect the CTRL socket on DVD 1 to the CTRL socket on your television.
> Connect the S-VIDEO socket on DVD 1 to the
S-VIDEO socket on your television.
> Connect the VIDEO socket on DVD 1 to the
VIDEO socket on your television.
> Connect the DIGITAL OUTPUT socket on DVD 1 to the COAX socket on your television.
> Connect the LINE OUT L and LINE OUT R sockets for left and right channel audio output on DVD 1 to the L and R sockets on your television.
> Finally, connect your DVD 1 to the mains with the enclosed cable. Your DVD 1 is now in stand-by mode – indicated by the red light in the display panel.
5
6 >> Set up DVD 1
You can connect DVD 1 to your tele vision via the socket panel on the rear of DVD 1.
Please consult the User’s Guides enclosed with externally connected equipment to ensure that it is connected in the proper manner.
MAINS CTRL SERVICE
LINE OUT R
LINE OUT L
VIDEO
DIG. OUT
CVBS
RGB
Y/C
AV S-VIDEO
Overview of the rear socket panel
~ (mains)
Socket for connection to the mains.
The switch options
CVBS
This switch setting is used when you connect DVD 1 to an AV 9000, BeoVision LX, BeoVision MS or
BeoVision MX 4000/4002/6000/7000 television. SERVICE
For use by qualifi ed service personnel only.
LINE OUT R VIDEO
LINE OUT L DIG. OUT
Audio signals are sent from DVD 1 to your television via these four sockets. All four sockets are used when you connect DVD 1 to a Bang & Olufsen television which does not use a 21-pin video cable.
The DIGITAL OUTPUT socket is also used when connecting DVD 1 to any Bang & Olufsen television equipped with a Dolby Digital surround sound module.
Y/C
This switch setting is used when you connect DVD 1 to a BeoVision Avant 50 Hz television.
RGB
This switch setting is used when you connect DVD 1 to any other Bang & Olufsen television.
AV
21-pin socket for connection to the Bang & Olufsen television.
CTRL S-VIDEO
Video signals are sent from DVD 1 to your television via these sockets. The sockets are used to connect
DVD 1 to a Bang & Olufsen television which does not use a 21-pin video cable.
Set up DVD 1 with your particular television…
This procedure will ensure that your DVDs are played with the proper picture format, regardless of the type of television you have.
DVD 1 must be switched on before you perform this ‘once only’ operation.
Press LIST on Beo4 until V.SETUP* appears in the Beo4 display
LIST
V.SETUP
Press GO to display TUNE GO
TUNE
Press 1 if your DVD 1 is connected
directly to a television from the
BeoVision MX-series (i.e. 4000/
4002, 6000/7000)
1
Press 2 if your DVD 1 is connected to a BeoVision MX via an AV2
Expander box, or if it is connected to any other Bang &
Olufsen television
2
Press GO to store the setup GO
*Add V.SETUP to Beo4…
Before you can set up DVD 1 to the correct television type, you must add one ‘button’ to the Beo4 remote control; V.SETUP is needed to set up DVD 1.
> Hold the • button while pressing LIST.
> Now, let go of both buttons.
> Press LIST until ADD? appears in the display.
> Press GO to call up the list of ‘buttons’ to add from.
> Press LIST until V.SETUP is displayed.
> Press GO to add the ‘button’. ADDED appears in the Beo4 display and you leave the setup function.
You only need the V.SETUP ‘button’ once and can therefore remove it after setting up DVD 1, if you wish. This is done by repeating the procedure described above, selecting REMOVE? instead of
ADD?.
7
8
Introducing DVD 1
In this chapter, you will find instructions explaining how to gain access to DVD 1 functions via the close-up operation panel on the front of DVD 1 and via the Beo4 remote control.
The close-up operation panel allows you to load and unload discs, to start, pause or stop playback, to cue forward or backward on a disc or to view the elapsed playing time.
EJECT PLAY
To load a disc…
> Press EJECT on the close-up operation panel.
The loader slides out.
> Place a disc in the loader. For information about valid disc formats, refer to ‘Play other disc formats’ on page 11.
> Press the DVD button on Beo4 or PLAY on the close-up operation panel to close the loader and start playback.
You can load a disc for playback at a later time.
Press EJECT from stand-by mode, place a disc in the loader, and press EJECT again. DVD 1 will remain in stand-by mode.
The close-up operation panel
EJECT
Press to open or close the loader.
Press to cue backward or forward during playback.
PLAY
Press to start playback. Press again to pause playback at the current still picture or audio track.
• (Stand-by)
Press to switch DVD 1 to stand-by mode. Stops playback without switching to standby if pressed during playback or pause mode.
DISPLAY
The display to the right shows the elapsed playing time of a DVD or the current track number being played on an audio CD. Switching DVD chapters causes the appropriate chapter number to be shown in the display for a few seconds.
Use the Beo4 remote control
Use the Beo4 remote control to operate DVD 1.
The functions activated by the particular buttons are described below.
Some functions require you to press GO, followed by a particular key. For example, to bring up the
DVD player menus, you must press GO, followed by 3. Other functions can be activated directly.
The display window shows you the current source or function.
Press GO, followed by…
1 to bring up the disc’s own top menu
– if your disc has one
2 to zoom in on the picture
3 to bring up the DVD player menus
4 to bring up the status display
or to switch to the next or previous chapter on a DVD
or to wind backwards or forwards during playback
GO to enter a choice or setting in a menu
1
GO
2
3
4
TV
SAT
LIGHT RADIO
DVD CD
V MEM RECORD A MEM
7
4
1
TEXT
8
5
2
0
9
6
3
MENU
GO
LIST
STOP
EXIT
DVD
0 – 9
Without pressing GO in advance, press…
DVD to begin playback of a loaded disc
The number buttons to select DVD titles and chapters or tracks
The arrow buttons to move from menu item to menu item
MENU
GO
EXIT
STOP
MENU to bring up the main menus
GO to resume playback that you have paused or stopped
The green button to select a subtitle language*
The yellow button to bring up the DVD disc menu
The red button to select another audio language*
The blue button to bring up the camera angle menu
EXIT to exit on-screen menus and remove the tool bar
STOP to pause or stop playback completely
*Alternative subtitle and audio languages are only available on some discs.
If your Beo4 remote control does not have a DVD button, press LIST until CDV is shown in the Beo4 display and press GO. For further information about how to add CDV to the Beo4 list, refer to page 7.
9
10
Daily use
Load a DVD and playback starts automatically.
While playing a DVD, use the Beo4 remote control to search at varying speeds, step through the disc, or bring up a DVD disc menu. You can resume playback of a DVD where you stopped last time, unless the loader has been opened in the meantime.
While playing a CD, you can pause playback, switch to a new track, cue back and forth at different speeds or select a track by its number.
Play and change chapters on a DVD…
Press to start playing a DVD DVD
Press GO then or to step to the next or previous chapter
GO
Press GO then or repeatedly to jump to another chapter on the disc
Enter the chapter number to step directly to a chapter
GO
1 – 9
Press GO, then or to wind backwards or forwards during playback. Press GO then or again to change speed
GO
Press DVD to resume playback DVD
Pause, slow playback or stop playback of a DVD…
Press STOP to pause playback STOP
From pause mode, press GO then or to start slow playback. Press GO then or to change speed
GO
Press STOP again to stop playback completely, or…
STOP
Press STOP a third time to return to the beginning of the DVD
STOP
Press GO to resume playback
Some DVDs offer special features which are temporarily available during playback, such as additional film sequences. In such situations, press GO twice in rapid succession to select this special feature.
GO
Use DVD on-screen menus…
Press the green button to bring up the subtitle language menu.
Press the green button repeatedly to switch between the available options. When you have made your selection, the menu disappears
Press the red button to bring up the audio language menu.
Press the red button repeatedly to switch between the available options. When you have made your selection, the menu disappears
Press the blue button to bring up the camera angle menu.
Press the blue button repeatedly to switch between the available options. When you have made your selection, the menu disappears
Press the yellow button to bring up the disc menu
In the disc menus…
Use the arrow keys to move between options in the menus
Press GO twice to enter your choice or setting
GO
GO
While DVD is selected…
Press GO then 1 to bring up the disc’s own top menu*. Press GO then 1 again to remove the menu
GO
1
Use the arrow keys to move between options in the menus
Press GO twice to enter your choice or setting
GO
GO
Press GO then 2 to zoom in on the picture. Press GO then 2 to increase the zoom factor. Press
GO then 2 a third time to exit the zoom feature
GO
2
Press GO then 3 to bring up the
DVD main menu. This is described on the next page
GO
3
Press GO then 4 to bring up the status display. Press GO then 4 again to change to the next display. Press GO then 4 a third time to remove the status display
GO
4
*Not all discs contain a top menu.
Play and change tracks on an audio CD…
Press to start playing a CD DVD
Press to step to the next or previous track
Press repeatedly to jump to another track on the CD
Enter the track number to step directly to a track on a CD
1 – 9
Pause or stop playback of an audio CD…
Press to pause playback STOP
STOP Press again to stop playback completely
Press to resume playback GO
Cue or wind through an audio CD…
Press to wind back and forth during playback
Press to resume playback GO
To play other disc formats:
Your DVD 1 is designed to play back different disc formats. Supported formats are:
– DVD-Video
– Audio CD
– Video CD
– CD-R/RW
– DVD-R/RW, provided that these are recorded using the DVD Video format and that the disc is fi nalized.
– Discs containing mp3 fi les are supported if the sampling frequency is set to 32, 44.1 or
48 Khz.
When playing discs with mp3 fi les, use
and to change folders and and to step between tracks.
11
12
Preference settings
The DVD main menus enable you to select your preferred settings for DVD playback.
In these menus you can, for example, search through a specific title or chapter, repeat playback of a selected section, or enter settings for picture format and language.
For further information about the menus, refer to the chapter On-screen
menus on page 14.
Play Mode
Initial Settings
Disc Navigator
Play Mode
A-B Repeat
Repeat
Random
Search Mode
A (Start Point)
B (End Point)
Off
How to use the DVD menus…
> Press GO then 3 to bring up the DVD main menu.
> Press or to move to the menu you wish to enter and press GO twice.
> Use the arrow keys , , and to move between menus and settings.
> Press GO twice to store your choice.
> Press EXIT to leave on-screen menus.
What’s on the Play Mode menu...
The Play Mode menu allows you to make selections for playback. The following options are available:
A–B Repeat… The A–B repeat function allows you to specify two points on a disc that form a loop to be played over and over.
Repeat… The repeat function allows you to repeat a title or a chapter on a disc over and over.
Random… The random play function allows you to play titles or chapters on a disc in random order.
Search Mode… The search mode function allows you to search through a disc, either by searching for a specifi c title or chapter, or by searching for a moment in elapsed time on a disc.
NOTE! This DVD player is set for the appropriate region from the factory. Discs from incompatible regions will not play on this player.
Initial Settings
Video Output
Language
Display
Options
TV Screen
S-Video Out
16:9 (Wide)
S1
DVD
Disc Navigator
Title 1-9
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 1-28
Chapter 001
Chapter 002
Chapter 003
Chapter 004
Chapter 005
Chapter 006
Chapter 007
Chapter 008
What’s on the Initial Settings menu...
The Initial Settings menu enables you to choose your preferred settings for DVD playback. Settings in this menu cannot be entered during playback.
The following options are available:
Video Output… This menu allows you to select, for example, a picture format suitable for your television.
Language… This menu allows you to store your preferred language for audio, subtitles and the disc menu, and to decide whether or not available subtitles should be shown during playback.
Display… This menu allows you to select the language of the player menus, to decide whether or not status displays should be shown on the screen, and whether the angle indicator should be shown. The angle indicator is only available if the disc contains the alternate camera angle feature.
Options… Some DVDs feature a Parental Lock level. If you specify a level lower than the one contained on the disc, the disc will not play unless your pincode is entered. Some discs also support the Country Code feature. This means that the player does not play certain scenes on a disc, depending on the Country Code and the
Parental Lock level you set. Before you can set the Parental Lock level or the Country Code, you must enter a pincode. You can change the pincode at any time.
If you forget your pincode, you must disable the
Parental Lock, as described to the right.
If you forget your Parental Lock pincode…
> Disconnect DVD 1 from the mains.
> While pressing and holding the PLAY and buttons, reconnect DVD 1 to the mains.
> Wait two seconds, then release both buttons.
> The next time you switch on DVD 1, the
Parental Lock will be deactivated.
What’s on the Disc Navigator menu...
The Disc Navigator menu allows you to quickly step to specifi c titles or chapters on a disc.
13
NOTE! Some DVDs will require you to choose a subtitle language from a disc menu, even if you have previously selected a default subtitle language from the ‘Language’ menu.
14
On-screen menus
In order for you to find your way through the on-screen menus the system offers, this chapter illustrates the overall structure of the menu system.
The chapter also gives you detailed information about the individual menus which offer numerous settingup and adjustment options.
Play Mode
B (End Point)
Off
Repeat
Title Repeat
Repeat Off
Random
Random Title
Random Chapter
Random Off
Title Search
Chapter Search
Time Search
The extended on-screen menu system for DVD 1.
Press DVD, then MENU on Beo4 to access the menu system.
Initial Settings
TV Screen
S-Video Out
Language
Audio Language
Subtitle Display
Display
OSD Language
On Screen Display
Angle Indicator
Options
Parental Lock
Disc Navigator
DVD
Title 1
Chapter 001
Title 9
Chapter 029
Play Mode
A-B Repeat
Repeat
Random
Search Mode
A (Start Point)
B (End Point)
Off
Play Mode
A-B Repeat
Repeat
Random
Search Mode
Title Repeat
Chapter Repeat
Repeat Off
Play Mode
A-B Repeat
Repeat
Random
Search Mode
Random Title
Random Chapter
Random Off
What’s on the A–B Repeat menu…
The A–B Repeat function allows you to specify two points on a disc that form a loop to be played over and over.
What’s on the Repeat menu…
The Repeat function allows you to repeat a title, chapter or track on a disc over and over.
When you select the start or end point in the menu, the current playback point is stored. It is not possible to enter a point in playback time with the digit keys.
When you select a title, chapter or track in the menu, the current one is stored. It is not possible to enter a title, chapter or track number with the digit keys.
Select Off when you no longer wish to repeat playback of the selected section of the disc.
Select Repeat Off when you no longer wish to repeat playback of the selected section of the disc.
What’s on the Random menu…
The Random function allows you to play titles, chapters or tracks on a disc in random order.
Select Random Off when you no longer wish to repeat playback of the selected section of the disc.
15
16
Play Mode
A-B Repeat
Repeat
Random
Search Mode
Title Search
Chapter Search
Time Search
>> On-screen menus
Initial Settings
Video Output
Language
Display
Options
TV Screen
S-Video Out
16:9 (Wide)
S1
Initial Settings
Video Output
Language
Display
Options
Audio Language English
Subtitle Language English
DVD Menu Lang. English
Subtitle Display On
What’s on the Search Mode menu…
The Search Mode function allows you to search through a disc, either by searching for a specifi c title or chapter, or by searching for a moment in elapsed time on a disc.
Use the number buttons, or to move to this point in time.
What’s on the Video Output menu…
TV Screen… Select a picture format for your television. Options are 4:3 (Letter Box)*,
4:3 (Pan&Scan) and 16:9 (Wide).
S-Video Out… Options are S1 and S2. Select S1.
*In ‘4:3 (Letter Box)’ the film is shown with black bars at the top and bottom of the screen.
What’s on the Language menu…
Audio Language… Select the language for audio playback from the languages shown, and if your preferred language is available on your DVDs, then audio playback will be in that language.
Subtitle Language… Select your preferred subtitle language from the languages shown, and if your preferred language is available on your DVDs, then subtitles will be shown in that language*.
DVD Menu Language… Select your preferred language for the disc menus from the available languages shown, and if your preferred language is available on your DVDs, then the disc menus will be in that language.
Subtitle Display… Select whether or not subtitles are to be displayed during playback.
*Some DVDs will require you to choose a subtitle language from a disc menu, even if you have previously selected a default subtitle language from the ‘Language’ menu.
Initial Settings
Video Output
Language
Display
Options
OSD Language
On Screen Display
Angle Indicator
English
On
On
Initial Settings
Video Output
Language
Display
Options
Parental Lock Off (US)
DVD
Disc Navigator
Title 1-9
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 1-28
Chapter 001
Chapter 002
Chapter 003
Chapter 004
Chapter 005
Chapter 006
Chapter 007
Chapter 008
What’s on the Display menu…
OSD Language… Select the language for the menus from the languages shown.
On Screen Display… Select whether or not status displays are to be shown on the screen. Options are On and Off.
Angle Indicator… Select whether or not you wish the camera icon to appear on the screen during scenes with multiple camera angles. Options are
On and Off.
What’s on the Parental Lock menu…
Some DVDs feature a Parental Lock level. If you specify a level lower than the one contained on the disc, the disc will not play unless your pincode is entered.
Some discs also support the Country Code feature.
This means that the player does not play certain scenes on the disc, depending on the Country Code you set.
What’s on the Disc Navigator menu…
The Disc Navigator menu allows you to quickly step to specifi c titles or chapters on a disc. Use the arrow buttons to select a title and chapter and press GO twice to start playback.
Before you can set the Parental Lock level or the
Country Code, you must enter a pincode. You can change the pincode at any time in the Parental
Lock menu.
Menus for the pincode, Parental Lock level and
Country Code appear when you set Parental Lock to On. Use the number buttons, or on Beo4 to enter your pincode, Parental Lock level and
Country Code and press GO twice to store your settings.
17
18
Maintenance
Regular maintenance, such as cleaning the system, is the responsibility of the user. To achieve the best result, follow the instructions to the right.
Contact your Bang & Olufsen retailer to determine recommendations for regular maintenance.
Any defective parts are covered by the guarantee during the warranty period.
Cleaning DVD 1
Wipe dust off the surface of DVD 1 using a dry, soft cloth. If necessary, remove grease stains or more persistent dirt with a fi rmly wrung soft cloth which you have dipped in a solution of water containing a few drops of mild detergent.
Keep the loader closed as much as possible to prevent build-up of dust on the lens. Do not attempt to clean the optics of DVD 1 or open DVD 1 yourself. Leave such operations to qualifi ed service personnel.
No solvents or abrasive cleaners should ever be used on DVDs, video CDs or audio CDs. When cleaning your discs, wipe in a straight line from the centre to the edge.
Never use alcohol or other solvents to clean any part of DVD 1!
Handling your discs
Handle discs with care. If the disc is always held by its edges and placed in its original cassette when out of DVD 1, no cleaning will be required. Should the disc become soiled by fi ngerprints, dust or dirt, it can be wiped clean with a lint-free, soft, dry cloth.
Avoid extreme heat and humidity, and never write on your discs.
19
20
Index
Beo4 remote control
Introducing Beo4, 9
Camera angle
Bring up the camer angle menu, 10
CD
Change tracks on an audio CD, 11
Load and play an audio CD, 8
Close-up operation panel
The close-up operation panel, 8
Connections
Connect DVD 1 to your television, 5
Contact
Contact Bang & Olufsen, 22
Cue/Wind
On an Audio CD, 11
On a DVD, 10
Disc
Handling your discs, 18
Displays and menus
DVD 1 display, 8
On-screen menus – index, 14
DVD
Bring up the camera angle menu, 10
Disc navigation, 10–11
DVD – Audio language, 16
DVD – on-screen menus, 14–17
DVD operation, 10
DVD – Parental Lock, 17
DVD – Subtitle Language, 16
Load and play a DVD, 8
Format
What’s on the Video Output menu, 16
Language
DVD – Audio Language, 16
DVD – Subtitle Language, 16
What’s on the Language menu, 16
Maintenance
Cleaning DVD 1, 18
Handling your DVD discs, 18
Pause
Pause or stop playback of a DVD, 10
Pause or stop playback of an audio CD, 11
Picture
What’s on the Video Output menu, 16
Pincode
DVD – Parental Lock, 17
Placement
DVD 1 placement guidelines, 4
Playback
Change tracks on an audio CD, 11
Cue back and forth on an audio CD, 11
Load and play a DVD, 8
Load and play an audio CD, 8
Pause or stop playback of a DVD, 10
Pause or stop playback of an audio CD, 11
What’s on the Play Mode menu, 12
Wind and rewind through a DVD, 10
Television
Set up DVD 1 with your particular television, 7
Tracks
Play and change tracks on an audio CD, 11
Random
What’s on the Random menu, 15
Repeat
What’s on the A–B Repeat menu, 15
What’s on the Repeat menu, 15
Search
Search through a DVD, 10
Search through an audio CD, 11
What’s on the Search Mode menu, 16
Socket panel
Connect DVD 1 to your television, 6
Stop
Pause or stop playback of a DVD, 10
Pause or stop playback of an audio CD, 11
Subtitles
DVD – Subtitle Language, 16
21
22
For your information…
The DVD Video logo is a registered trademark.
Your needs as a user are given careful consideration during the design and develop ment process of a Bang & Oluf sen product and we strive to make our products easy and comfortable to operate.
This product incorporates copyright protection tech nology that is protected by claims of certain
US patents and other intellectual property rights owned by Macrovision Corporation, and other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macro vision Corporation. Reverse engineering or disassembly is prohibited.
Therefore, we hope that you will take the time to tell us about your experiences with your Bang & Olufsen product. Any thing which you consider important – positive or negative – may help us in our efforts to refi ne our products.
Thank you!
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confi dential unpublished works. Copyright 1992-1997. All rights reserved.
Write to: Bang & Olufsen a/s
Consumer Service dept. 7210
Peter Bangsvej 15
DK–7600 Struer
or fax: Bang & Olufsen
Consumer Service
+45 97 85 39 11 (fax)
or e-mail: [email protected]
Visit our Web-site on… www.bang-olufsen.com
This product fulfils the conditions stated in the
EEU directives 89/336 and 73/23.
CLASS 1
LASER PRODUCT
The label on the compact disc player serves as a warning that the apparatus contains a laser system and is classifi ed as a class 1 laser product.
In case any diffi culties arise with the compact disc player, please contact a Bang & Olufsen retailer.
The apparatus must be opened by qualifi ed service personnel only.
CAUTION: The use of any controls, adjustments or procedures other than those specifi ed herein may result in hazardous radiation exposure. The use of optical instruments with this product will increase eye hazard. As the laser beam used in this CD/DVD
Player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualifi ed personnel only. Laser radiation when open. Do not stare into beam. This label is located on the rear enclosure.
3508795
0403 Printed in Denmark by Bogtrykkergården a-s, Struer
www.bang-olufsen.com

Public link updated
The public link to your chat has been updated.
Advertisement