Atop | ABLELink SE5001 | User`s manual | Atop ABLELink SE5001 User`s manual

Atop ABLELink SE5001 User`s manual
ABLELink®
SE5001 Ethernet Serial Server
Quick Start Guide
Version 1.3
Updated on 2007/05/24
Tel: 886-3-5508137
Fax: 886-3-5508131
http://www.atop.com.tw
Quick Start Guide Version 1.3
SE5001 Ethernet Serial Server
刪除: 1
This document is intended to provide customers with brief descriptions on the product and to assist
customers to get started. For detail information and operations of the product, please refer to the user’s
manual in the product CD.
1.Packaging
Please check your package contains the following items:
ƒ SE5001-S2 or SE5001-S5- Serial Server
ƒ
Quick Start Guide
ƒ
Product CD
ƒ
Wall mounting screws
ƒ
ƒ
3 pin terminal block for power input
格式化: 項目符號及編號
Optional Accessories:
1. DK-25 DIN-Rail Kit
2. Power Adapter with DC jack- PIN 1.3φ output 5V 1A
(1) AD5V1A(US) Switching adapter
(2) AD5V1A(EU) Switching adapter
3. Power Adapter with Terminal block output 12V1.25A
(1) US315-12(US) Switching adapter
(2) US315-12(EU) Switching adapter
2.Hardware Setup
SE5001 interfaces
NOTE:
1. SE5001-S2 (for RS-232), SE5001-5 (for RS-422/RS-485)
2. One can press the reset button of SE5001 to reset the settings to the default value
Figure 2.1 shows the interfaces.
Figure 2.1. SE5001 Interface
Copyright © 2006 Atop Technologies, Inc.
All rights reserved. Designed in Taiwan.
1
格式化: 項目符號及編號
Quick Start Guide Version 1.3
SE5001 Ethernet Serial Server
刪除: 1
LED Indicators:
LAN LED
Message
Description
Off
Ethernet Disconnected
Blinking with Green
Data is transmitting on Ethernet for 100Mbps
Blinking with Orange
Data is transmitting on Ethernet for 10Mbps
Table 1. LAN LED Message
COM Port LED
Message
Description
Off
No data is transmitting on COM port
Blinking
Data is transmitting on COM port
Table 2. COM Port LED Message
RUN LED
Message
On
Description
Jumper JP1 Pin1 and Pin2 are shorted to disable
AP firmware running
Blinking (rate: 0.5 Sec)
AP firmware is running normally
Table 3. RUN LED Message
Installation Procedures:
Step 1: Connect SE5001 to power source using 5V DC Jack
(or 9~30V DC Terminal Block power source)
Note: SE5001 provide two power inputs can be connected simultaneously to live DC power
sources. Anyone of the power inputs fails, the other live source acts as a backup to support
power needs automatically. The redundant dual DC power inputs give you extra assurance of
non-stop operation
Step 2: Connect SE5001 to ones Ethernet network. Use a standard straight-through Ethernet cable
when one connect it to a hub/switch, one also can connect it to ones PC‘s Ethernet port via a
cross-over Ethernet cable for easy set up. However, in this case one need to make sure ones
PC is in the same network sub-net as SE5001.
Step 3: Connect SE5001’s serial port to a serial device.
Step 4: Placement options. One can mount SE5001 to a wall/panel (Mounting screws included) or
Din-Rail rack (Require optional item model: Din-Rail-Kit DK-25).
3. Software Setup
Default Network Setting:
Default User Name/Password:
IP: 10.0.50.100
User Name: admin
Gateway: 10.0.0.254
Password: null (leave it blank)
Subnet: 255.255.0.0
Auto IP (Dynamic IP):
A DHCP server can automatically assigns the IP address and network settings. SE5001 supports the
DHCP function. By default, the DHCP function on SE5001 is disabled; you can use Monitor.exe to
enable this function. (ref Figure 3.1)
Copyright © 2006 Atop Technologies, Inc.
All rights reserved. Designed in Taiwan.
2
刪除: putting a check on
Auto IP on Dialog window.
Quick Start Guide Version 1.3
SE5001 Ethernet Serial Server
刪除: 1
Figure 3.1. monitor.exe utility Dialog Window
Assign a Static IP address by:
A. Using Telnet
1. Telnet to SE5001 using DOS command “Telnet IP_address”. Example: telnet 10.0.50.100
2. SE5001’s network, link mode and COM ports settings can be configured in the telnet window
B. Using Monitor.exe Utility
Use Monitor.exe which comes inside the Product CD to automatically search for all SE5001
connected to ones local area network. Then please select the desired SE5001 to configure the
network setting individually.
C. Using Web Browser
1.
Make sure ones PC is located on the same network sub-net as SE5001
2.
2Open a web browser, then type in the IP address of SE5001 to be configured. Default user
name is admin and default password is null (leave it blank).
3.
3SE5001’s network, link mode and COM ports settings can be configured in different web pages.
4.
Click “Save Configuration” to save settings.
5.
Click ”Restart” button to make the change effective if necessary.
4. Pin Assignments
The pin assignments of DB9 connector on SE5001 is shown in the following table:
Pin#
RS-232
Full Duplex
for SE5001-S2 Model
RS-485 2-wire
Half Duplex
for SE5001-S5 Model
RS-422/RS-485 4-wire
Full Duplex
for SE5001-S5 Model
1
DCD
N/A
N/A
2
RXD
N/A
TXD+
3
TXD
DATA+
RXD+
4
DTR
N/A
N/A
5
SG (Signal Ground)
SG (Signal Ground)
SG (Signal Ground)
6
DSR
N/A
N/A
7
RTS
DATA-
RXD-
8
CTS
N/A
TXD-
9
N/A
N/A
N/A
Customer Services and Supports
1. Contact your local dealers or Atop Technical Support Center at the following numbers.
y +886-3-550-8137 (Atop Taiwan)
y +86-21-6495-6232 (Atop China)
2. Report the errors via Atop’s Web site or E-mail account
www.atop.com.tw, service@atop.com.tw
www.atop.com.cn, service@atop.com.cn
Copyright © 2006 Atop Technologies, Inc.
All rights reserved. Designed in Taiwan.
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising