DeLonghi | Dishwasher | Technical data | DeLonghi Dishwasher Technical data

DeLonghi Dishwasher Technical data
Contents
MAKING HOT CHOCOLATE....................................... 14
Preparing and attaching the hot chocolate carafe (D)............. 14
INTRODUCTION....................................................... 8
MAKING MILK DRINKS........................................... 15
Symbols used in these instructions........................................... 8
Letters in brackets..................................................................... 8
Troubleshooting and repairs..................................................... 8
Fundamental safety warnings . ................................................ 8
Filling and attaching the milk container . ............................... 15
Adjusting the amount of froth . .............................................. 15
Making flat white/cappuccino/latte/milk .............................. 15
Programming the quantities of coffee and milk in the cup . ... 15
Cleaning the milk container after use..................................... 15
DESIGNATED USE..................................................... 8
MAKING LONG COFFEE ........................................... 16
SAFETY................................................................... 8
Customising the “My LONG coffee” quantity .......................... 16
INSTRUCTIONS........................................................ 9
DELIVERING HOT WATER AND STEAM...................... 16
DESCRIPTION.......................................................... 9
Delivering hot water . ............................................................ 16
Change the quantity of water delivered automatically. ......... 16
Steam delivery ....................................................................... 17
Tips for using steam to froth milk . ......................................... 17
Clean the steam/hot water spout after use............................. 17
Description of the appliance . .................................................. 9
Description of touch screen....................................................... 9
Description of milk container.................................................... 9
Description of hot chocolate carafe .......................................... 9
Description of hot water/steam spout....................................... 9
Description of the accessories................................................... 9
MEMORISING YOUR PERSONAL PROFILE ................. 17
PRELIMINARY CHECKS........................................... 10
CLEANING ............................................................. 17
Checking the appliance........................................................... 10
Installing the appliance . ........................................................ 10
Connecting the appliance ...................................................... 10
Using the appliance for the first time ..................................... 10
Cleaning the machine ............................................................ 17
Cleaning the coffee grounds container.................................... 18
Cleaning the drip tray............................................................. 18
Cleaning the inside of the machine......................................... 18
Cleaning the water tank . ....................................................... 18
Cleaning the coffee spouts ..................................................... 18
Cleaning the pre-ground coffee funnel .................................. 18
Cleaning the infuser ............................................................... 18
Cleaning the hot chocolate carafe (D) .................................... 19
Cleaning the milk container (C) .............................................. 19
TURNING THE APPLIANCE ON................................. 10
TURNING THE APPLIANCE OFF................................ 11
MENU SETTINGS.................................................... 11
Rinsing.................................................................................... 11
Select background.................................................................. 11
Descale . ................................................................................. 11
Install water filter (some models only)................................... 11
Set time.................................................................................. 11
Auto-start............................................................................... 11
Auto-Off (Standby)................................................................. 12
Energy Saving......................................................................... 12
Coffee temperature................................................................. 12
Setting water hardness .......................................................... 12
Beep....................................................................................... 12
Default values (reset).............................................................. 12
Statistics . ............................................................................... 12
Setting the language ............................................................. 12
DESCALING ........................................................... 20
SETTING WATER HARDNESS ................................... 20
Measuring water hardness ..................................................... 20
Set water hardness . ............................................................... 20
WATER SOFTENER FILTER . ..................................... 21
Installing the filter ................................................................. 21
Replacing the filter . ............................................................... 21
Removing the filter ................................................................ 21
TECHNICAL DATA ................................................... 21
DISPOSAL.............................................................. 22
MAKING COFFEE.................................................... 12
DISPLAYED MESSAGES........................................... 22
Selecting the coffee taste........................................................ 12
Selecting the quantity of coffee in the cup . ........................... 12
Customising the “My coffee” quantity . .................................. 13
Adjusting the coffee mill ........................................................ 13
Tips for a hotter coffee ........................................................... 13
Making espresso coffee using coffee beans............................. 13
Making espresso coffee using pre-ground coffee.................... 13
TROUBLESHOOTING............................................... 24
Electrical requirements (UK only).................. 26
7
INTRODUCTION
•
•
•
Thank you for choosing the ESAM6900 automatic coffee,
cappuccino and hot chocolate machine.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the appliance.
•
•
Symbols used in these instructions
Important warnings are identified by these symbols.
It is vital to respect these warnings.
•
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
•
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Never touch the appliance with damp hands or feet.
Never touch the plug with damp hands.
Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
Unplug directly from the plug only. Never pull the power cable as you could damage it.
To disconnect the appliance completely, place the main
switch at the back of the appliance in the 0 position (fig.
5).
If the appliance is faulty, do not attempt to repair. Turn it off, unplug from the mains socket and contact
Customer Services.
If the plug or power cable is damaged, do not use the
appliance. Have the plug and/or cable replaced by
De’Longhi Customer Services only to avoid all risk.
Important!
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Important!
The appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children must be
supervised to ensure they do not play with the appliance.
Please note:
This symbol identifies important advice or information for the
user.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on page 3.
Danger: Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the sections “Displayed messages” on
page 22 and “Troubleshooting” on page24.
If this does not resolve the problem or you require further
information, you should consult Customer Services by calling
the number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
If repairs are required, contact De’Longhi Customer Services
only.
The addresses are given in the guarantee certificate provided
with the machine.
DESIGNATED USE
This appliance is designed and made to prepare coffee and heat
drinks. All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
This is a household appliance only.
It is not intended to be used in:
• staff kitchen areas in shops, offices and other working
environments;
• farm houses;
• by clients in hotels, motels and other residential type
environments;
• bed and breakfast type environments.
SAFETY
Fundamental safety warnings
Danger!
This is an electrical appliance. Failure to respect the instructions
could cause electric shock.
You should therefore respect the following safety warnings:
8
INSTRUCTIONS
B7.
B8.
B9.
B10.
B11.
B12.
B13.
Read these instructions carefully before using the appliance.
- Failure to respect these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
Please note:
Keep these instructions.
If the appliance is passed to other persons, they must also be
provided with these instructions.
B14.
B15.
LONG icon: to deliver a cup of LONG coffee.
MILK icon: to deliver a cup of milk.
LATTE icon: to deliver a cup of latte.
CAPPUCCINO icon: to deliver a cappuccino.
FLAT WHITE icon: to deliver a flat white.
CHOCOLATE icon: to make hot chocolate.
icon: changes function according to the text
displayed alongside the icon
icon: to select the coffee taste.
icon: to select the coffee quantity.
Please note :
A light touch is enough to activate the icon.
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Funnel and measure compartment cover
A2. Measure compartment
A3. Pre-ground coffee funnel
A4. Cup shelf (cup warmer when Energy Saving is
disabled)
A5. Touch screen (B)
A6. Hot water and steam nozzle
A7. Coffee spout (adjustable height)
A8. Cup tray
A9. Drip tray
A10. Drip tray water level indicator
A11. Service door
A12. Infuser
A13. Water tank
A14. Grounds tray
A15. Coffee guide
A16. Grinding adjustment dial
A17. Beans container lid
A18. Beans container
A19. Main switch (on back of machine)
A20. ON/STANDBY button
Description of milk container
(page 2 - C )
C1. Lid with milk frother
C2. Froth adjustment and CLEAN dial
C3. Frothed milk spout (adjustable)
C4. Lid release buttons
C5. Milk intake tube
C6. Milk container
C7. Thermal casing
Description of hot chocolate carafe
(page 2 - D )
D1 Hot chocolate carafe lid
D2. Funnel
D3. Steam spout
D4. Stirrer
D5. Hot chocolate carafe
D6. Funnel release button
Description of hot water/steam spout
(page 2 - E )
E1. Release button
E2. Spout
E3. Steam nozzle
E4. Cappuccino maker
Description of touch screen
(page 3 - B )
Only the icons relating to the controls enabled for the particular
function currently being used will be lit on the touch screen.
B1.
icon: changes function according to the text
displayed alongside the icon
B2. Display: guides the user in using the appliance.
B3.
icon: changes function according to the text
displayed alongside the icon
B4.
icon: to deliver one cup of espresso coffee.
B5.
icon: to deliver two cups of espresso coffee.
B6.
icon: changes function according to the text
displayed alongside the icon
Description of the accessories
(page 2 - F )
F1. Pre-ground coffee and hot chocolate powder measure
F2. Cleaning brush
F3. “Total Hardness Test” indicator paper
F4. Descaler
F5. Water softener filter (some models only)
9
PRELIMINARY CHECKS
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the I position
(fig. 1).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds):
2. When “English” appears, press the OK icon (fig. 2) ffor a
few seconds until “English set” is displayed.
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Services.
Installing the appliance
Follow the instructions indicated by the appliance:
3.
FILL WATER TANK!”: remove the
water tank, fill to the MAX line with
fresh water then replace in the
appliance (fig. 3).
Important!
When you install the appliance, you should respect the
following safety warnings:
• The appliance gives off heat. After positioning the appliance on the worktop, leave
a space of at least 3 cm between the surfaces of the
appliance and the side and rear walls and at least 15 cm
above the coffee machine.
• Water infiltration could damage the appliance and cause
electric shock.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
4.
5.
6. The appliance starts delivering water from the hot water
spout.
7. The appliance ends the first start up procedure and goes
off automatically.
The coffee machine is now ready for normal use.
Connecting the appliance
•
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the I position (fig. 1).
Each time the coffee machine is turned on, it performs an
automatic preheat cycle and, if necessary, a rinse cycle which
cannot be interrupted. The appliance is ready for use only after
completion of this cycle.
Using the appliance for the first time
•
Please note:
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before it starts
to give satisfactory results.
TURNING THE APPLIANCE ON
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
•
INSERT WATER SPOUT”: Check that
the hot water spout is inserted on
the nozzle and place a container
with a minimum capacity of 100 ml
underneath (fig. 4).
PRESS OK”: press the OK icon on the display.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath. Avoid contact with
splashes of water.
• To turn the appliance on, press the button for a few
moments (fig. 5):
Please note :
Coffee has been used to factory test the appliance and it
is therefore completely normal for there to be traces of
coffee in the grinder.
The machine is, however, guaranteed to be new.
You should customise water hardness as soon as possible
following the instructions in the section “Setting water
hardness” (page 20).
The message “Heating up, please wait” is
displayed.
10
Press the OK icon to select the function. Press the
or icon to select the required background,
then press OK again to confirm the choice.
When heating is complete, the message changes
to “Rinsing”.
The appliance is ready for use when an espresso
coffee cup appears on the display.
Please note!
This menu item can be customised in all profiles (see
“Memorising your personal profile” on page 17).
TURNING THE APPLIANCE OFF
Descale
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
Install water filter (some models only)
For instructions on the water filter, see page 21.
For instructions on descaling, see page 20.
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Please note:
If you will not be using the appliance for some time, unplug
from the mains socket:
• first turn the appliance off by pressing the
button
(fig. 5);
• place the main switch in the 0 position (fig. 6).
Set time
To adjust the time on the display, proceed as follows:
Press the OK icon to select the function. Set the
hour using the
symbol to increase and the
symbol to decrease, then press OK again to
confirm, then adjust the minutes. Finally press
OK to memorise the time set.
Important!
Never place the main switch in the 0 position while the
appliance is on.
Please note!
Hold the
or
symbol down to run through the hours and
minutes quickly.
MENU SETTINGS
To access the settings menu, press the MENU icon. Scroll through
the menu by pressing the or icon.
To exit the menu, press the ESC icon.
The following can be selected from the menu: Rinsing, Select
background, Descale, Install water filter, Set time, Auto-start,
Auto-off, Energy Saving, Set temperature, Water hardness, Beep,
Default values, Statistics, Set language.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
•
Rinsing
Use this function to deliver hot water from the spout to heat the
internal circuit and make the coffee delivered hotter.
•
Press the OK icon to select the function. Press OK
again to confirm and start rinsing.
After rinsing, the appliance is automatically ready to make the
next drink.
Please note!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
•
•
Select background
Use this function to change the colour of the display
background.
11
Please note!
For the appliance to come on at the set time, the time
must be set correctly.
To set the auto-start time, the hour must first have been
set.
Press the OK icon to select the function, then
press OK again to confirm.
Adjust the time as described in the previous
section and confirm with OK. The grey symbol
indicates that the function is not active.
Please note!
When the function is active, the
symbol appears
alongside the current time.
To disable the function, access the menu and select the
function as described above. “DISABLE?” is displayed.
Press OK to confirm. The symbol alongside the current
•
time disappears.
When the main switch is turned off, the “Auto-Start” setting is reset.
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as set).
Press the OK icon to select the function. Press OK
again to confirm and reset to the default values.
Auto-Off (Standby)
You can set the auto-off time so that the appliance switches off
after 15 or 30 minutes, or after 1, 2 or 3 hours.
Press the OK icon to select the function. Press the
or
icon to select the required time, then
press OK again to confirm.
Statistics
-
-
Energy Saving
Use this function to enable or disable Energy Saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
Press the OK icon to select the function, then press
OK again to enable or disable Energy Saving.
•
•
•
-
-
-
-
Setting the language
To modify the language of the display, proceed as follows:
Press the OK icon to select the function. Press the
or
icon to select the required language,
then press OK to confirm the choice.
Please note!
When the function is active, the
symbol appears
alongside the current time.
A few seconds may elapse between Energy Saving and
delivery of the first drink.
When Energy Saving is disabled, the appliance turns the
cup warmer on automatically.
MAKING COFFEE
Selecting the coffee taste
The appliance is set by default to make coffee with a standard
taste. You can select one of the following tastes displayed
under the glass:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
Coffee temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
Press the OK icon to select the function. Press
the
or
icon to select the required
temperature, then press OK again to confirm.
Please note!
This menu item can be customised in all profiles (see
“Memorising your personal profile” on page 17).
To change the taste, press the
until the required taste is displayed.
Setting water hardness
For instructions on setting water hardness, see
page 20.
icon (fig. 7) repeatedly
Selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee.
To select the quantity of coffee, press the
icon (fig.
8) repeatedly until the message corresponding to the required
quantity of coffee is displayed:
Beep
This enables or disables the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed. The
beep is active by default.
Press the OK icon to select the function. Press
OK again to enable or disable the beep. The grey
symbol indicates that the function is not active.
Default values (reset)
This displays statistics relating to the machine.
Press the
or
symbol to display the
available data:
number of coffees delivered;
number of milk drinks delivered (CAPPUCCINO, LATTE,
FLAT WHITE, MILK);
number of times the machine has been descaled;
total litres of water delivered;
number of water filters used;
number of hot chocolates delivered.
Corresponding
coffee
My coffee
12
espresso (ml)
≃30 (program.
from ≃20 to ≃180)
Short
≃40
Standard
≃60
Long
≃90
Extra long
≃120
Tips for a hotter coffee
For hotter coffee, you should:
• perform a rinse cycle before delivering the coffee, using
the “Rinsing” function in the menu;
• if Energy Saving is disabled, place the cups on the cup
warmer until they are warm;
• warm the cups by rinsing them with hot water (using the
hot water function);
• set a higher coffee temperature in the menu. Customising the “My coffee” quantity
The appliance is set by default to automatically
deliver 30 ml of “My coffee”. To modify this
quantity, proceed as follows:
Making espresso coffee using coffee beans
1. Place a cup under the coffee spouts (fig. 9).
2. Press the
icon repeatedly (fig. 8) until “My
coffee” is displayed.
3. Press the 1 cup icon
(fig. 10). The appliance starts
making the coffee;
4. Press the PROG icon. The appliance starts programming;
5. As soon as the coffee in the cup reaches the required level,
press the STOP or
icon again.
The quantity set has now been programmed.
•
•
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1.
2.
3.
Fill the container with coffee beans (fig. 12).
Place under the coffee spouts:
- 1 cup, if you want to make 1 coffee (fig. 9);
- 2 cups, if you want 2 coffees (fig. 13).
Lower the spout as near as possible to the cup. This makes
a creamier coffee (fig. 14).
4. Press the icon corresponding to the number of coffees
required (one cup
or two cups
) (fig. 10
and 15).
5. The appliance starts making coffee. An image
corresponding to the type of preparation chosen is
displayed together with a progress bar which fills as
preparation proceeds.
Once the coffee has been made, the appliance prepares for use
again.
Please note :
You can programme a single cup of coffee only.
To cancel programming of “My coffee”, press the EXIT
PROG icon.
Please note!
“My coffee” can be customised in all profiles (see
“Memorising your personal profile” on page 17).
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that
delivery is either too fast or too slow (a drop at a time), this
can be corrected by adjusting the grinding adjustment dial
(fig. 11).
•
•
Please note!
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
For fuller bodied creamier coffee, turn
one click anticlockwise towards “1”
(finer ground coffee).
For faster delivery (not a drop at a time),
turn one click clockwise towards “7”
(coarser ground coffee).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered.
If delivery is still too fast or too slow, repeat the correction,
turning the dial another click.
Please note:
While the appliance is making coffee, delivery can be
interrupted at any moment by pressing the STOP icon or
one of the coffee icons (
or
).
At the end of delivery, to increase the quantity of coffee
in the cup, just press one of the coffee icons (
or
) within 3 seconds.
Important!
If the coffee is delivered a drop at a time, too fast and not creamy
enough or too cold, read the tips in the “Troubleshooting”
section on page 24).
Various alarm messages could be displayed while using the
machine. Their meaning is explained in the section “Displayed
messages” (page 22).
Making espresso coffee using pre-ground coffee
•
13
Important!
Never add pre-ground coffee when the machine is off or it
•
could spread through the inside of the machine and dirty
it. This could damage the appliance.
Never use more than one level measure or it could dirty
the inside of the machine or block the funnel.
•
Important!
Make sure the hole in the funnel shown in fig. 21 is clean.
Please note!
The milk must be poured into the funnel when the steam
spout and stirrer are already in place. Do not exceed the
MAX level marked on the carafe. Increase or reduce the
quantity of hot chocolate powder according to taste.
• To use water instead of milk, follow the instructions for
milk.
• To prepare hot chocolate correctly, first pour the milk into
the funnel, then add the hot chocolate or cocoa powder as
shown on the hot chocolate carafe lid.
5. Close the lid (fig. 22).
6. Attach the carafe to the nozzle and push as far as it will go
(fig. 23). The machine emits a beep (if the beep function
is enabled).
7. Press the CHOCOLATE icon (B12).
•
Please note!
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
1. Press the
icon (fig. 7) repeatedly to select the
pre-ground coffee symbol
.
2. Put one level measure of pre-ground coffee into the
funnel (A3) (fig. 16).
3. Place a cup under the coffee spouts (fig. 9).
4. Press the 1 cup coffee icon
.
5. The appliance starts making coffee. An image
corresponding to the type of preparation chosen is
displayed together with a progress bar which fills as
preparation proceeds.
8. Select one or two cups (
) by pressing the
corresponding icon.
8. Press the + or - icon to select the required density:
Thick density
Please note:
• While the appliance is making coffee, delivery can be
interrupted at any moment by pressing the STOP icon or
one of the coffee icons (
or
).
• To increase the quantity of coffee in the cup, just press the
coffee icon
within 3 seconds.
Once the coffee has been made, the appliance prepares to
make the next drink.
Medium density
Thin density
MAKING HOT CHOCOLATE
Please note!
A few seconds may elapse between Energy Saving and delivery
of the first drink.
If the hot chocolate powder used does not contain
thickener, there will not be any change adjusting the
density.
9. Press the CHOCOLATE icon to start making hot chocolate
(fig. 24). The appliance starts mixing the drink and then
delivers steam to heat it.
Once the coffee has been made, the appliance prepares for use
again. The chocolate is ready to be poured into the cup.
Preparing and attaching the hot chocolate carafe (D)
Please note!
You can make one or two cups of hot chocolate.
1. Lift the carafe lid (fig. 17).
2. Make sure the steam spout is inserted in the chocolate
funnel and the stirrer is inserted in both the holes in the
funnel (fig. 18).
3. Attach the funnel to the carafe (fig. 19).
4. To make one cup of hot chocolate, pour milk at refrigerator
temperature (or fresh water) into the funnel up to the
level and add 2 measures (25 g) of hot chocolate
powder or cocoa. To make two cups or one mug of hot
chocolate, pour milk (or water) into the funnel up to the
level and add 4 measures of powder (50
g) (fig. 20).
Danger of burns!
While making the chocolate, the carafe and lid become very
hot. Hold by the handle only to remove the carafe and pour the
chocolate.
The chocolate is ready to be poured into the cup.
•
14
.
Please note!
To interrupt making the chocolate, press the CHOCOLATE
icon again or the STOP icon.
Danger of burns!
While making the hot chocolate, it is normal for steam to
•
•
Making flat white/cappuccino/latte/milk
1. Press the icon corresponding to the required drink.
2. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. Delivery of milk stops
automatically and (if needed for the drink), coffee
delivery starts. An image of the drink being prepared is
displayed (fig. 32) together with a progress bar which fills
gradually.
come out of the holes in the chocolate carafe lid.
Heating the milk causes splashes inside the carafe. This is
normal.
The hot chocolate quantity in the cup will vary varying the
density: if you choose thick density, there will be fewer
chocolate than that contained in the cup if choosing the
other densities.
MAKING MILK DRINKS
Please note!
Milk or coffee delivery can be interrupted by pressing the STOP
icon. To stop preparation altogether, press the ESC icon.
Please note!
A few seconds may elapse between Energy Saving and delivery
of the first drink.
Programming the quantities of coffee and milk in the
cup
The appliance is set by default to automatically deliver standard
quantities. To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press the icon corresponding to the function to be
programmed (flat white, cappuccino, latte, milk). The
machine starts delivering milk.
3. Press the PROG icon.
4. When the required quantity of milk has flowed into the
cup, press the STOP MILK icon.
5. If needed for the drink, after a few seconds, the machine
starts delivering coffee. When the required quantity of
coffee has flowed into the cup, press the STOP COFFEE
icon. Coffee delivery stops.
The machine is now reprogrammed with the new quantities.
Filling and attaching the milk container
1. Press the release buttons and lift the milk container lid
(fig. 25).
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level (fig. 26).
Please note!
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
To avoid milk with poor froth or large bubbles, always clean
the milk lid and hot water nozzle as described in the section
“Cleaning the milk container” on pages 36 and 40.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 27).
4. Attach the lid back on the milk container.
5. Attach the container to the nozzle, pushing as far as it will
go (fig. 28).
6. Place a sufficiently large cup under the coffee spouts and
frothed milk spout (fig. 29). To use particularly tall cups/
glasses, lift the coffee and milk spouts (fig. 30).
7. Follow the instructions below for each function.
•
Milk drinks can be customised in all profiles (see
“Memorising your personal profile” on page 17).
Cleaning the milk container after use
Adjusting the amount of froth
Turn the froth adjustment dial on the milk container lid to
adjust the amount of froth on the milk delivered while making
milk drinks (fig. 31). Follow the tips given in the following
table:
Dial
position
Description
Recommended for…
No froth
FLAT WHITE /
MILK (hot milk)
Min. froth
LATTE
Max. froth
Cappuccino /
MILK (frothed milk)
Please note!
To cancel programming of the drinks, press the EXIT
PROG icon.
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
After preparing a milk drink, the machine must
be cleaned to remove the milk residues. Proceed
as follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
15
3. Turn the froth adjustment dial to CLEAN (fig. 33): ): the
operation is shown on the display (fig. 34) and stops
automatically.
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
nozzle with a sponge (fig. 35).
•
•
•
1. Place a sufficiently large cup or glass under the coffee
spouts (fig. 9).
2. Press the
icon repeatedly (fig. 8)until “My
coffee” is displayed.
3. Press the LONG icon. The machine starts delivering
coffee;
4. Press the PROG icon. The appliance starts programming;
5. As soon as the coffee in the cup reaches the required level,
press the STOP icon again.
The quantity set has now been programmed.
Please note!
To prepare a number of milk drinks, clean the milk
container after you have prepared the last drink only.
The milk container can be kept in the refrigerator.
In some cases, to clean you must wait for the appliance to
heat up.
•
MAKING LONG COFFEE
“My LONG coffee” can be customised in all profiles (see
“Memorising your personal profile” on page 17).
1. Choose the length and taste required, following the same
procedure as for espresso coffee.
Corresponding
coffee
LONG (ml)
My coffee
≃ 100 (program. from 20
to 250)
Short
≃ 125
Standard
≃ 175
Long
≃ 210
Extra long
≃ 250
Please note!
To cancel programming of “My LONG coffee”, press the
EXIT PROG icon.
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Do not leave the appliance unattended while delivering hot
water or steam. The spout becomes hot during delivery. Hold
by the handle only.
Please note!
If Energy Saving is active, you may have to wait a few seconds
before hot water and steam are delivered.
Delivering hot water
1. Check that the hot water spout is attached correctly.
2. Place a container under the water spout (as close as
possible to avoid splashes) (fig. 4).
3 Press the
icon (fig. 37).
4. Hot water delivery begins and then stops automatically.
A progress bar fills gradually as preparation proceeds. To
interrupt delivery of the hot water manually, press the
STOP icon again.
2. Press the LONG icon (fig. 36).
3. The appliance starts making coffee. An image
corresponding to the type of drink chosen is displayed
together with a progress bar which fills as preparation
proceeds.
Please note!
To interrupt delivery, press the LONG icon or the STOP icon.
Please note!
The quantity of hot water can be customised in all
profiles (see “Memorising your personal profile” on page
17).
Making long coffee using pre-ground coffee
1. Select the pre-ground coffee symbol, as explained in the
espresso section.
2. Push the LONG icon (fig. 36).
3. The appliance starts making coffee. An image
corresponding to the preparation chosen is displayed
together with a progress bar which fills as preparation
proceeds.
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water. To modify these quantities, proceed as follows:
1. Check that the hot water spout is attached correctly.
2. Position a container under the spout.
3. Press the
icon, then the PROG icon.
4. When the hot water in the cup reaches the required level,
press the STOP icon.
Customising the “My LONG coffee” quantity
The appliance is set by default to automatically
deliver 100 ml of “My coffee”. To modify these
settings, proceed as follows:
16
MEMORISING YOUR PERSONAL PROFILE
The machine is now reprogrammed with the new quantity.
•
With this appliance, you can memorise six
different profiles, each associated with a
different colour.
In each profile you can customise:
Please note!
To cancel programming, press the EXIT PROG icon.
Steam delivery
1. Check that the hot water spout is attached correctly.
2. Fill a container with the liquid to be heated or frothed and
immerse the steam spout in the liquid.
3 Press the
icon (fig. 37). After a few seconds, the steam
to heat the liquid comes out of the cappuccino maker;
4. When the required temperature is obtained, interrupt
steam delivery by pressing the STOP icon. (You should
not discharge steam for more than 3 minutes at a time).
- the quantities of espresso and long “My coffee”;
- the quantities for all milk drinks;
- the quantity of hot water;
- the preferred background (from the menu);
- the coffee temperature (from the menu).
To use the function, proceed as follows:
1. Enter the “Profiles” section by pressing the icon;
2. Choose your colour by pressing the CHANGE icon and
then press the OK icon to confirm. The chosen colour
appears at the bottom left of the display to indicate you
are operating with that profile;
3. Proceed to programme the drinks which can be memorised
as described above. Each time you access the profile, the
machine uses the programmed settings.
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow
movements in an upward direction.
• To avoid milk with poor froth or large bubbles, always
clean the spout as described in the following section.
Please note!
To change the profile, access profile selection by pressing the
icon at the bottom left corresponding to the colour in use:
• Press the CHANGE icon to enter another profile and OK to
confirm;
• Press the icon to exit all profiles.
• When operating in the menu, the selected profile is
displayed to the right (for selecting background and
temperature).
Clean the steam/hot water spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and deliver
a little water by pressing the
icon (fig. 34). Stop
delivery of hot water by pressing the STOP icon again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout (fig. 38) by
pressing the button. Hold the spout with one hand and
with the other, turn the cappuccino maker and pull it
downwards (fig. 39).
3. Also remove the steam nozzle by pulling it downwards
(fig. 40).
4. Check the hole in the nozzle shown by the arrow in fig. 41
is not blocked. If necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
6. Insert the nozzle and cappuccino maker on the nozzle
by pushing it upwards and turning it clockwise until it is
attached.
CLEANING
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- coffee grounds container (A14),
- drip tray (A9),
- the inside of the machine, accessible after opening the
service door (A11),
- water tank (A13),
- coffee spouts (A7) and hot water nozzle (A6),
- pre-ground coffee funnel (A3),
- infuser (A12),
- touch screen (B)
- milk container (C)
- hot chocolate carafe (D)
- hot water/steam spout (E)
•
17
Important!
Do not use solvents, abrasive detergents or alcohol to
clean the appliance. With De’Longhi superautomatic
•
•
Cleaning the inside of the machine
coffee machines, you need not use chemical products to
clean the machine.
No parts of the appliance are dishwasher safe, apart from
the hot chocolate carafe (D) and components of the milk
container in contact with the milk.
The thermal casing C7 cannot be washed in a
dishwasher or immersed in water.
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
off (see “Turning off”) and unplugged from the mains power
supply. Never immerse the coffee machine in water.
1. Check regularly (about every 100 coffees) that the inside
of the appliance (accessible after removing the drip tray)
is not dirty. If necessary, remove coffee deposits with the
brush supplied and a sponge.
2. Remove the residues with a vacuum cleaner (fig. 45).
Cleaning the coffee grounds container
The display indicates when the grounds
container is full. The appliance cannot be used
to make coffee until you have cleaned the
grounds container. Even if not full, the empty
grounds container message is displayed 72 hours after the first
coffee has been prepared. For the 72 hours to be calculated
correctly, the machine must never be turned off with the main
switch in the 0 position.
To clean (with the machine on):
• Open the service door on the front of the appliance (fig.
42), extract the drip tray (fig. 43), empty and clean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
Cleaning the water tank
Clean the water tank about once a month and whenever you
replace the water softener filter (if present) as follows:
1. Remove the filter.
2. Clean the water tank with a damp cloth and a little mild
washing up liquid. Rinse with running water.
3. Rinse the filter (if present) and put back in the water
tank. Fill the tank with fresh water and put back in the
appliance.
Cleaning the coffee spouts
1. Clean the coffee spouts
with a sponge or cloth.
2. Check the holes in the
coffee spout are not
blocked.
If necessary, remove
coffee deposits with a
toothpick.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog the
machine.
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel is not blocked.
If necessary, remove coffee deposits with the brush supplied.
Cleaning the drip tray
Important!
If the drip tray is not emptied regularly, the water could overflow
from the edge and seep inside or around the machine.
This could damage the machine, the surface it rests on or the
surrounding area.
Cleaning the infuser
The infuser (A12) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 44). As soon as the indicator
becomes visible, the tray must be emptied and cleaned.
To remove the drip tray:
1. Open the service door (fig. 42);
2. Remove the drip tray and grounds container (fig. 43);
3. Empty the drip tray and grounds container and wash
them;
4. Replace the drip tray complete with grounds container;
5. Close the service door.
1. Make sure the machine is correctly turned off (see “Turning
off”).
2. Open the service door (fig. 42).
3. Remove the drip tray and grounds container (fig. 43).
4. Press the two red release
buttons inwards and at
the same time pull the
infuser outwards .
18
Please note!
It is normal to find residues on the stirrer while cleaning. These
consist of traces of iron in the cocoa attracted by the magnets
in the stirrer.
Important!
RINSE WITH WATER ONLY NO WASHING UP LIQUID - NO DISH
WASHER
Do not use washing up liquid to clean the infuser as it could
cause damage.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6. After cleaning, replace the infuser by sliding it onto the
internal support and pin at the bottom, then push the
PUSH symbol fully in until it clicks into place.
Cleaning the milk container (C)
Clean the milk container each time you prepare milk as
described below:
1. Lift and remove the
lid (C1);
2. Extract the milk
container (C5) from
the thermal casing
(C6), holding it by
the two side grips.
Important!
The thermal casing must not
be filled with or immersed in
water. Clean with a damp cloth
only.
Please note!
3. Remove the milk spout (C3)
and intake tube (C5).
4. Turn the froth adjustment
dial clockwise to the
“INSERT” position (see
figure) and pull off.
5. Wash all the components
of the frother thoroughly
with hot water and mild
washing-up liquid.
All components and the
container are dishwasher safe, placing them in the top
basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (see figure alongside). If necessary,
scrape the groove with a toothpick.
6. Rinse inside the froth adjustment dial seat with running
water (see figure) and the hole that connect the lid to the
appliance.
7. Check that the intake tube and spout are not clogged with
milk residues.
8. Replace the dial (lining up the arrow with the word
“INSERT”), the spout and the milk intake tube.
9. Place the milk container in the thermal casing.
10. Place the lid back on the milk container.
If you encounter difficulty
inserting the infuser, before
inserting it you must adapt it to
the right dimension by pressing it
forcefully from the bottom and
top as shown in the figure.
7. Once inserted, make sure the two red
buttons have snapped out.
8. Replace the drip tray and grounds
container.
9. Close the service door.
Cleaning the hot chocolate carafe (D)
Clean the carafe each time you prepare milk as described
below:
1. Lift and remove the lid (D1);
2. Remove the funnel (D2) by
2
pressing the release button
1
(D6) and lifting it ;
3. Extract the steam spout
(D3) and stirrer (D4);
4. Wash all the components
thoroughly with hot water
and mild washing-up
liquid.
All components are dishwasher safe, placing them
in the top basket of the dishwasher.
5. Replace all the components.
19
DESCALING
water and replace.
9. Empty the container used to collect the descaler solution
and replace it under the hot water spout.
10. Press the OK icon to start rinsing. Hot water comes out of
the spout.
11. When “Descaling complete” “PRESS OK” is displayed, press
the OK icon. The appliance goes off.
12. Put the water softener filter (if present) back and fill the
tank.
To use the appliance, press the
button.
When the symbol appears, you must proceed with the
descaling equipment.
Important!
It is vital to respect the manufacturer’s safety warnings given on
the descaler pack and the warnings relating to the procedure to
follow in the event of contact with the skin and eyes.
Please note!
Use descaler recommended by De’Longhi only.
Failure to descale the appliance as described above also
invalidates the guarantee.
SETTING WATER HARDNESS
Descaling is requested after a period of time established
according to water hardness.
The machine is set by default for a hardness value of 4 (very
hard water).
The machine can also be programmed according to the actual
hardness of the mains water in the various regions, varying the
frequency with which the message is displayed.
1. Turn the machine on.
2. Access the settings menu by pressing the MENU icon.
Scroll through the menu pressing the
and
icons
to select “Descale”.
3. Press the OK icon to select the function. Press OK again to
confirm.
4. “ADD DESCALER” “INSERT
WATER SPOUT” is displayed.
5. Empty the water tank
completely and remove
the water softener filter (if
present).
Pour the descaler into the tank
up to the level A (corresponding
A
to a 100 ml pack) marked on
B
the side of the tank (fig. 32),
then add water (1 litre) up to
level B (fig. 32) and put the
B
A
water tank back.
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper from
its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly.
After about a minute, 1, 2, 3, or 4 red squares form,
depending on the hardness of the water. Each square
corresponds to one level.
LEVEL 1
soft water
LEVEL 2
slightly hard water
Place an empty container with a minimum capacity of 1.5
litres under the hot water spout.
LEVEL 3
hard water
Important! Danger of burns
Hot water containing acid flows out of the hot water spout.
Avoid contact with splashes of water.
LEVEL 4
very hard water
Set water hardness
1.
Access the settings menu by pressing the
MENU icon. Scroll through the menu pressing
the
and
icons to select “Water
hardness”.
2. Confirm the selection by pressing the OK icon.
3. Press
or
to set the water hardness identified
using the indicator paper (see figure in the previous
section).
4. Press the OK icon to confirm the setting.
6. Start descaling by pressing the OK icon.
7. The descale programme starts and the descaler liquid
comes out of the water spout. The descale programme
automatically performs a series of rinses and pauses at
regular intervals to remove limescale deposits from inside
the machine. The cycle lasts about 30 minutes and is
indicated by a progress bar which fills and empties.
8. “Rinsing” “FILL WATER TANK”. The appliance is now ready
for rinsing through with clean water. Remove the water
tank, empty, rinse under running water, fill with clean
20
5. Press the ESC icon to exit the menu.
The machine is now reprogrammed with the new water
hardness setting.
8. Access the menu by pressing the MENU icon;
9. Scroll through the menu by pressing the or
icon
until “Install water filter” is displayed.
10. Press the OK icon.
11. The message “Install water filter” “CONFIRM?” is
displayed.
12. Press the OK icon to confirm the selection. The message
“INSERT WATER SPOUT”“PRESS OK” is displayed.
13. Position a container under the hot water spout (min.
capacity: 100 ml).
14. Press OK to confirm the selection. The appliance begins
delivering hot water and “Please wait” is displayed.
15. After delivery, the appliance is automatically ready to make
the next drink.
The filter is now active and you can use the coffee machine.
WATER SOFTENER FILTER
Certain models are fitted with a water softener filter. If this
is not the case with your model, you are recommended to
purchase one from De’Longhi Customer Services. To use the
filter correctly, follow the instructions below.
Installing the filter
1. Remove the filter from the packaging.
2. Turn the date indicator
disk until the next
two months of use are
displayed.
Replacing the filter
When the filter alarm is displayed, after two months
(see date indicator) or if the appliance has not been
used for 3 weeks, you should replace the filter:
1. Extract the tank and exhausted filter;
2. Remove the new filter from the packaging and proceed as
illustrated on the previous pragraph (points 3-4-5-6).
3. Position a container with a minimum capacity of 100 ml
under the hot water spout.
4. Access the menu by pressing the MENU icon;
5. Scroll through the menu by pressing the or
icon
until “Replace water filter” is displayed.
6. Press the OK icon.
7. “CONFIRM?” is displayed.
8. Press the OK icon to confirm.
9. “Water delivery” “PRESS ok” is displayed.
10. Press OK to confirm the selection. The appliance begins
delivering hot water and “Please wait” is displayed.
11. After delivery, the appliance is automatically ready to make
the next drink.
The new filter is now active and you can use the coffee
machine.
Please note
The filter lasts about two
months if the appliance is
used normally. If the coffee
machine is left unused with
the filter installed, it will last a
maximum of three weeks.
3. To activate the filter, let
tap water go in the hole
of the filter as shown in
the figure as long as the
water comes out from
the side openings for
over one minute.
4. Extract the tank from the
appliance and fill with
water.
5. Insert the filter in the
water tank and immerse
it completely for about
30 seconds, turning it
upside down to enable
the air bubbles to
escape.
6. Insert the filter in the
filter housing and press
as far as it will go.
7. Close the tank with the
lid, then put the tank
back in the machine.
Removing the filter
If you want to use the appliance without the filter, you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Extract the tank and exhausted filter.
2. Put the tank back in the appliance.
3. Access the menu by pressing the MENU icon.
4. Scroll through the menu by pressing the
or
icon
until “Remove water filter” is displayed.
5. Press the OK icon.
6. “CONFIRM?” is displayed;
When you install the filter, you must notify the appliance of its
presence.
21
7. Press the OK icon to confirm and the ESC icon to exit the
menu.
•
•
TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350W
Pressure:
15 bar
Water tank capacity: 1,4 litres
Size: LxHxD: 281x400x425 mm
Max. beans container capacity 250 g
Weight of machine (with drip tray)
13,8 Kg
Water/steam spout:
57g
Milk container: 720g
Hot chocolate carafe:
378g
Power cable length:
1,45m
•
•
The appliance complies with the following EC directives:
Standby Directive 1275/2008
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC Directive 2004/108/EC and subsequent
amendments;
Materials and accessories coming into contact with food
conform to EC regulation 1935/2004.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with
household waste, but taken to an authorised waste
separation and recycling centre.
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
Insufficient water in tank or tank not inserted correctly
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place.
The grinding is too fine and the coffee is delivered too slowly
or not at all.
Repeat coffee delivery and turn the grinding adjustment
dial one click clockwise towards “7” while the coffee mill is
in operation.
If after making at least 2 coffees delivery is still too slow,
repeat the correction procedure, turning the grinding
adjustment dial another click until delivery is correct.
If the problem persists, press OK to deliver water from the
spout until it flows out normally.
The water spout is not inserted or is inserted incorrectly.
Insert water spout as far as it will go.
The grounds container is too full or more than 3 days have
passed since delivery of the first coffee (this guarantees
correct hygiene of the machine).
Empty the grounds container and clean, then replace.
Important: when removing the drip tray, the grounds
container MUST be emptied, even if it contains few
grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog
the machine.
FILL WATER TANK
GROUND TOO FINE ADJUST
MILL
INSERT WATER SPOUT
EMPTY GROUNDS CONTAINER
22
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
After cleaning, the grounds container has not been
replaced.
Open the service door, remove the drip tray and insert the
grounds container.
The “pre-ground coffee” function has been selected
without placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel or deselect the
“pre-ground” function.
The funnel (A8) is blocked.
Empty the funnel with the help of the cleaning brush as
described in the section “Cleaning the pre-ground coffee
funnel”.
The machine must be descaled.
The descaling procedure described in the “Descaling”
section needs to be performed as soon as possible.
The water filter is exhausted.
Replace the filter or remove it as described in the section
“Water filter”.
Too much coffee has been used.
Select a milder taste or reduce the quantity of pre-ground
coffee.
The coffee beans have run out.
Fill the beans container
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of the brush as described in
the section “Cleaning the pre-ground coffee funnel”.
The infuser has not been replaced after cleaning.
Insert the infuser as described in the paragraph “Cleaning
the infuser”.
The milk container is not inserted correctly.
Insert the milk container as far as it will go.
After preparing a milk drink, the lid must be cleaned with
the CLEAN function.
Turn the froth adjustment dial to CLEAN
The froth adjustment dial in not in correct position.
Turn the froth adjustment dial in one of the froth position.
insert grounds container
ADD PRE-GROUND COFFEE
Descale
Replace water filter
Less coffee
FILL BEANS CONTAINER
INSERT INFUSER ASSEMBLY
INSERT MILK CONTAINER
TURN DIAL TO CLEAN
TURN FROTH ADJUSTMENT
DIAL
23
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
The hot chocolate carafe is not inserted correctly.
Insert the hot chocolate carafe correctly.
The service door is open
Close the service door.
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described in
the section “Cleaning and maintenance”.
If the message is still displayed after cleaning, contact
customer services.
The water circuit is empty.
Press OK to deliver water from the spout until it flows out
normally.
INSERT CHOCOLATE CARAFE
CLOSE DOOR
GENERAL ALARM
EMPTY CIRCUIT
FILL CIRCUIT
alternating with...
Water delivery
PRESS OK
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee is not hot
The cups were not preheated.
•
•
The coffee is not creamy
enough.
The coffee is delivered too
slowly or a drop at a time.
If Energy Saving is not active, leave the cups on the
cup warmer for at least 20 minutes for them to warm
up.
Warm the cups by rinsing them with hot water
(using the hot water function).
The infuser has cooled down because 2/3 minutes have
elapsed since the last coffee was made.
Before making the coffee, heat the infuser by performing a
rinse cycle (see the section “Tips for a hotter coffee”).
A low coffee temperature is set.
Set a higher coffee temperature in the menu.
The coffee is ground too coarsely.
Turn the grinding adjustment dial one click anticlockwise towards “1” while the coffee mill is in operation (fig. 11). Continue one click at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2 coffees.
Wrong type of coffee
Use a type of coffee for espresso coffee machines.
The coffee is ground too finely.
Turn the grinding adjustment dial one click clockwise towards “7” while the coffee mill is in operation (fig. 11). Continue one click at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2 coffees.
24
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee does not come out
of the spouts, but from around
the service door.
The holes in the spouts are clogged with dry coffee dust.
Clean the spouts with a toothpick, sponge or hard bristled
kitchen brush.
The coffee guide inside the service door is blocked and
cannot swing.
Thoroughly clean the coffee guide, particularly near the
hinges.
The coffee is delivered too
quickly.
The coffee is ground too coarsely.
Turn the grinding adjustment dial one click anticlockwise towards “1” while the coffee mill is in operation (fig. 11). Avoid
turning the grinding adjustment dial excessively otherwise
when you select two cups, the coffee may be delivered a
drop at a time.
Coffee does not come out of
one of the spouts.
The spouts are blocked.
Clean the spouts with a toothpick
Water comes out of the spouts
instead of coffee.
The pre-ground coffee may be blocked in the funnel (A8)
Empty the funnel with the help of the brush as described in
the section “Cleaning the pre-ground coffee funnel”.
The milk
does not
come out
of the milk
spout.
The milk container lid is dirty.
Clean the milk container lid as described in the section “Cleaning the milk container”.
The milk
contains
large
bubbles and
squirts out
of the milk
spout or
there is little
froth.
The milk is not cold enough or is not semi-skimmed.
Use skimmed or semi-skimmed milk at refrigerator temperature (about 5° C). If the result is not as you wished, try
changing brand of milk.
The froth adjustment dial is incorrectly adjusted.
Adjust following the instructions in the section “Making
drinks with milk”.
The milk container lid or froth adjustment dial are dirty
Clean the milk container lid and dial as described in the section “Cleaning the milk container”.
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section “Cleaning the
hot water/steam nozzle”.
The milk
contains
large
bubbles and
there is little
froth
The spout is dirty.
Clean as described in the section “Cleaning the spout after
use”.
The milk is not cold enough or is not semi-skimmed.
You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
If the result is not as you wished, try changing brand of
milk.
The steam nozzle has not been inserted after cleaning.
Replace all the spout components correctly.
It is not plugged into the mains socket.
Plug into the mains socket.
The main switch is not turned on.
Place the main switch in the I position
The
Hold the button down for a few seconds.
The appliance does not
come on
button has not been pressed sufficiently.
The LONG coffee has too
much froth
The coffee is ground too finely.
“Energy Saving” is enabled,
but the cup warmer is hot.
A number of drinks have been prepared in rapid succession.
Turn the grinding adjustment dial one click clockwise towards “7” while the coffee mill is in operation (fig. 11). Continue one click at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2 coffees.
25
PROBLEM
POSSIBLE CAUSE
SOLUTION
The chocolate is not
sufficiently dense
The hot chocolate powder used does not contain thickener.
Change the type of powder used.
The highest density has not been selected.
Select the highest density by pressing the + icon.
The quantities of milk and hot chocolate powder are not
correct.
Follow the instructions in the section “Making hot
chocolate”.
The stirrer and steam spout are not inserted correctly in the
funnel.
Insert the stirrer and steam spout in the funnel
The instructions have not been followed.
Pour the milk/water into the funnel first, followed by the hot
chocolate powder.
The magnets in the stirrer attract traces of iron naturally
present in the hot chocolate powder.
Clean as described in the section “Cleaning the hot chocolate
carafe”.
The hot chocolate is cold or
there are lumps.
During cleaning, there are
traces of black on the stirrer.
Electrical requirements (UK only)
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply
contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply
socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use.
important: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
13 amp
Fuse
green and yellow earth
blue neutral
brownlive
Blue to
neutral
Brown to
live
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as
follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol
or
coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. If your electricity
supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible
cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The
colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always state this colour when ordering
a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising