ifs vtvr73230-r3 install & oper instr

ifs vtvr73230-r3 install & oper instr
VT73230-R3
VR73230-R3
IFS Fiber Module
Installation & Operation
Instructions
P/N 1062785 • REV B • ISS 01AUG11
32 CHANNEL
DIGITAL VIDEO TRANSMITTER
ifs
32 CHANNEL
DIGITAL VIDEO TRANSMITTER
ifs
VIDEO STATUS
A
B
POWER
VIDEO STATUS
ifs
32 CHANNEL
DIGITAL VIDEO TRANSMITTER
ifs
VIDEO STATUS
CHAN 5
CHAN 9
CHAN 13
CHAN 17
CHAN 21
CHAN 25
CHAN 29
CHAN 2
CHAN 6
CHAN 10
CHAN 14
CHAN 18
CHAN 22
CHAN 26
CHAN 30
CHAN 3
CHAN 7
CHAN 4
CHAN 8
POWER
CHAN 11
CHAN 15
CHAN 12
CHAN 16
VT73230
POWER
VT73230
CHAN 19
CHAN 23
CHAN 20
CHAN 24
}
ifs
32 CHANNEL
DIGITAL VIDEO RECEIVER
ifs
VIDEO STATUS
CHAN 1
CHAN 5
CHAN 2
CHAN 6
OPTICAL
CARRIER
VIDEO STATUS
CHAN 9
CHAN 13
CHAN 10
CHAN 14
ifs
OPTICAL
CARRIER
CHAN 3
CHAN 7
CHAN 4
CHAN 8
VR73230
POWER
CHAN 15
CHAN 12
CHAN 16
VR73230
CHAN 32
Video detected from the transmitter
ifs
32 CHANNEL
DIGITAL VIDEO RECEIVER
ifs
VIDEO STATUS
VR73230
CHAN 28
Power
32 CHANNEL
DIGITAL VIDEO RECEIVER
POWER
CHAN 31
Video input from a camera
VIDEO STATUS
CHAN 25
CHAN 29
CHAN 22
CHAN 26
CHAN 30
CHAN 19
CHAN 23
OPTICAL
CARRIER
CHAN 27
CHAN 20
CHAN 24
CHAN 17
CHAN 21
CHAN 18
OPTICAL
CARRIER
CHAN 11
CHAN 27
VT73230
A
B
C
Simplex Single
Mode Fiber
Optic Cable
32 CHANNEL
DIGITAL VIDEO RECEAIVER
POWER
VT73230
3 rack slots wide
POWER
ifs
VIDEO STATUS
CHAN 1
VT73230
B
32 CHANNEL
DIGITAL VIDEO TRANSMITTER
VR73230
POWER
CHAN 28
VR73230
CHAN 31
CHAN 32
PS-R3
POWER SUPPLY
115VAC - 1A 50/60HZ
220VAC - 1/2A 50/60HZ
POWER
ifs
International
Fiber
Systems
Incorporated
ifs
Status indicating
LEDs will change
from RED to GREEN
with these conditions.
PS-R3
POWER SUPPLY
115VAC - 1A 50/60HZ
220VAC - 1/2A 50/60HZ
POWER
ifs
International
Fiber
Systems
Incorporated
ifs
}
}
1 rack slot wide
13 rack slots wide
PCB's
VT/VR71630-R3 REAR VIEW
Chan 29
Chan 25
Chan 21
Chan 17
Chan 13
Chan 9
Chan 5
Chan 1
Chan 30
Chan 26
Chan 22
Chan 18
Chan 14
Chan 10
Chan 6
Chan 2
Chan 31
Chan 27
Chan 23
Chan 19
Chan 15
Chan 11
Chan 7
Chan 3
Chan 32
Chan 28
Chan 24
Chan 20
Chan 16
Chan 12
Chan 8
Chan 4
POWER
Simplex Single Mode
Fiber Optic Cable
Between VT73230-R3
and VR73230-R3
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CLASS 1 LASER PRODUCT
(For purposes of IEC 60825-1)
Complies with FDA Performance Standard for Laser Products
Title 21
Code of Federal Regulations
Subchapter J
Comprehensive
Lifetime Warranty
(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specifications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontinuance, warranty support is limited to five (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for products not
manufactured by Seller (e.g., fiber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period offered by
the original manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notified of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and maintenance, and conformance with any applicable recommendations of
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.
(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,
(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
efforts, the parties will negotiate an equitable adjustment in price.
(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,
all such liability shall terminate and BUYER shall have a reasonable time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.
Contacting us
For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).
Sales and support contact information
North
America
Toll-free: 855.286.8889 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.
Outside the toll-free area: 503.885.5700.
E-mail: [email protected]
Europe
Select Contact Us at www.utcfssecurityproducts.eu
Australia
[email protected]
Note: Be ready at the equipment before calling.
Online
Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:
http://www.interlogix.com/transmission1
1.
Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will
need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Copyright
Trademarks and
patents
Manufacturer
Certification
ACMA compliance
Canada
European Union
directives
© 2011 UTC Fire & Security. All rights reserved.
Interlogix and IFS names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
N4131
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement