Sharp | ER-A420 | PROGRAMMING MANUAL - Inland Cash Register

PROGRAMMING MANUAL - Inland Cash Register
q PROGRAMMING MANUAL
CODE : 00ZERA410UPME
ELECTRONIC
CASH REGISTER
ER-A410
MODEL ER-A420
ER-A410
(For “U/A” version)
SRV KEY : LKGIM7113RCZZ
PRINTER : PR-45M II
ER-A420
CONTENTS
CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . 1 - 1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE. . . . . . . . . . . . . . 2 - 1
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . 3 - 1
Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CHAPTER 1. SERVICE (SRV) MODE
The SRV key is used for SRV mode operations.
■ PROGRAM RESET
A MASTER RESET clears the entire memory and resumes initial values.
Please use “Procedure A”, “Procedure B” or “Procedure C”
A PROGRAM RESET initializes the program without clearing memory.
Prodecure A: 1) Set the mode switch to the (SRV’) position.
2) Plug in the AC power cord into the wall outlet.
There are 2 kinds of MASTER RESET operations.
3) Without pressing any function keys, turn the mode
switch to (SRV) position from (SRV’) position.
MASTER RESET 1: Normal MASTER RESET
Clears the entire memory and resumes initial
values.
Procedure B: 1) Unplug the AC power cord from the wall outlet.
MASTER RESET 2: Enables the layout of the fixed keys in addition
to performing a MASTER RESET 1.
2) Set the mode switch to the (SRV) position.
3) Without pressing any function keys, plug the AC power
cord into the wall outlet.
Fixed keys: [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [00]
[000] [.] [CL] [@/FOR] [SBTL]
[CA/AT]
Procedure C: 1) Unplug the AC power cord from the wall outlet.
2) Set the mode switch to the PGM2 position.
3) While holding down the JOURNAL FEED key & the
RECEIPT FEED key, plug in the AC power cord to the
wall outlet.
1. RESET PROCEDURES
■ MASTER RESET 1
*“Procedure C” can be executed when SRV#926-B is +4: PROGRAM
RESET in PGM2 = ENABLE.
Please use “Procedure A” or “Procedure B”
Note: Procedure B and C cannot reset the hardware.
Procedure A must be used to reset the hardware.
Procedure A: 1) Set the mode switch to the (SRV’) position.
2) Plug the AC power cord into the wall outlet.
3) While holding down the JOURNAL FEED key, turn
the mode switch to (SRV) position from the (SRV’)
position.
2. SETUP PROCEDURES
■ MASTER RESET 1
Procedure B: 1) Unplug the AC power cord from the wall outlet.
1) During the memory clearing and initializing, “***MRS.***” is
displayed on upper line.
2) Set the mode switch to the (SRV) position.
3) While holding down the JOURNAL FEED key, plug in
the AC cord to the wall outlet.
2) When the MASTER RESET is performed, the buzzer beeps 3 times
and MASTER RESET*** is printed.
Note: Procedure B cannot reset the hardware.
Procedure A must be used to reset the hardware.
■ MASTER RESET 2
1) The fixed key code and text that may be programmed is displayed.
■ MASTER RESET 2
ex) 001 0 KEY
Please use “Procedure A” or “Procedure B”
3
002 1 KEY
3 ...
Procedure A: 1) Set the mode switch to the (SRV’) position.
2) During memory clearing and initializing, “***MRS.***” is displayed on upper line.
2) Plug in the AC power cord into the wall outlet.
3) While holding down the JOURNAL FEED key & the
RECEIPT FEED key, turn the mode switch to (SRV)
position from (SRV’) position.
3) When the MASTER RESET is performed, the buzzer beeps 3 times
and MASTER RESET*** is printed.
4) Program the [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [00] [000]
[.] [CL] [@/FOR] [SBTL] [CA/AT] keys by depressing
the desired keys in this order.
■ SERVICE RESET
1) When a SERVICE RESET is performed, “PROGRAM RESET ***”
is printed. Buzzer does not beep.
Note: If the [000] key is not required, press the same
key at the next step, and the [000] key will be
inhibited.
3. READING OF THE SRV MODE PROGRAM
Procedure B: 1) Unplug the AC power cord from the wall outlet.
List of program reports
2) Set the mode switch to the (SRV) position.
3) While holding down the JOURNAL FEED key & the
RECEIPT FEED key, plug the AC power cord into the
wall outlet.
4) Repeat the same sequence as in “Procedure A”
Note: Procedure B cannot reset the hardware.
Procedure A must be used to reset the hardware.
JOB#
Report name
900
SRV-mode program full item report (not incl. keyboard layout)
950
Keyboard layout report (except Dept. key & PLU key)
951
Keyboard layout report (only Dept. key & PLU key)
990
SSP report
Note: Program reports are printed on the RECEIPT & JOURNAL.
ER-A410U/A420U
SERVICE (SRV) MODE
1–1
[JOB# 950]
*This following sample program readings are based on the ER-A420.
Reading the contents of the SRV mode programming for the FREE KEY
LAYOUT setting. (Function Keys)
[JOB# 900]
Reading the contents of the SRV mode programming
Key operation
Key operation.
950
900
@/FOR
@/FOR
CA/AT
CA/AT
Date/Time/Cashier code
Machine No./CC-No./Cashier name
Cashier code/Cashier name
Date/Time/Cashier code
Machine No./CC-No./Cashier name
Cashier code/Cashier name
Job code
Contents of the
SRV-mode programming
Job code
Key No./Key text/Location No.
General Z1 reset counter
Houlry Z1 reset counter
PLU Z1 reset counter
Cashier Z1 reset counter
PBLU Z1 reset counter
General Z2 reset counter
Daily net Z2 reset counter
GT2
GT3
TR
PGM2 mode secret code
Training cashier No.
Training mode title
Memory Allocation
Department
PLU record
PBLU record
Cashier
Domestic currency symbol
Initial text mode
programming
The programming contents are printed only on the journal for individual
formats as shown above.
ER-A410U/A420U
SERVICE (SRV) MODE
1–2
[JOB# 951]
Reading the contents of the SRV mode programming for FREE KEY
LAYOUT setting. (Dept. & PLU keys)
Key operation
951
@/FOR
CA/AT
Date/Time/Cashier code
Machine No./CC-No./Cashier name
Cashier code/Cashier name
Job code
Key No./Key label/Location No.
ER-A410U/A420U
SERVICE (SRV) MODE
1–3
[JOB#990]
Reading the contents of the SRV mode programming for the SSP settings.
Key operation
990
@/FOR
CA/AT
Date/Time/Cashier code
Machine No./CC-No./Cashier name
Cashier code/Cashier name
Job code
SSP No. (Reading report only)
ER-A410U/A420U
SERVICE (SRV) MODE
1–4
4. SERVICE MODE PROGRAMMING
[JOB#903] ER-A410: MRS = 5000
ER-A420: MRS = 5000
The following are the key operations required for programming.
#903-A: 1. Baud Rate for ECR data copying
0
XXX
[A] [B] [C] [D]
@/FOR
(Job#)
CA/AT
1. Baud rate (bps)
903-A
9600
4
19200
5
Numeric entry
4 digits max
★
#903-B: 1. Symbol of scale entry
Details of [A] [B] [C] [D] will be discussed at each item description.
★ mark is MRS setting.
1. Symbol of scale entry
903-B
“LB”
0
“KG”
2
[JOB#901] ER-A410: MRS = 0002
ER-A420: MRS = 0002
★
#903-C: 1. Entry of tare
#901-A: Not used (Fixed at “0”)
2. Unit of weight for the scale
#901-B: Tax system
1. TAX system
901-B
Auto TAX 1~4 Manual TAX
0
Canadian TAX (Type1 to Type10)
6
Canadian TAX (TypeΙΙ: VAT on VAT)
7
1. Entry of tare
2. Unit of weight for
the scale
★
Disallowed
Allowed
#901-C: 1. Rounding system
1. Rounding system
901-C
Normal
0
Singapore
8
901-D
0.
0
0.0
1
0.00
2
0.000
3
2ID (3ID) + 2DD
0
1ID (2ID) + 3DD
1
2ID (3ID) + 2DD
2
1ID (2ID) + 3DD
3
★
#903-D: 1. Food stamp system
★
#901-D: 1. TAB setting
1. TAB setting
903-C
1. Food stamp system
903-D
No food stamps
0
TAX not payable in food stamps
1
TAX payable in food stamps
2
Food stamp forgiveness
3
★
[JOB#904] ER-A410: MRS = 0000
ER-A420: MRS = 0000
★
#904-A: 1. Printing of date
[JOB#902] ER-A410: MRS = 0000
ER-A420: MRS = 0000
1. Printing of date
904-A
Yes
0
No
4
★
#904-B: 1. Printing of Consecutive No.
#902-A, B, C, D: Not used (Fixed at “0000”)
1. Printing of Consecutive No.
904-B
Yes
0
No
4
#904-C, D: Not used (Fixed at “00”)
ER-A410U/A420U
SERVICE (SRV) MODE
1–5
★
[JOB#905] ER-A410: MRS = 0005
ER-A420: MRS = 0005
[JOB#906] ER-A410: MRS = 0021
ER-A420: MRS = 0021
#905-A: 1. Taxable 4 subtotal printing on X/Z report.
#906-A: 1. Printing of PLU codes
2. Gross Tax 4 and refund Tax 4 total print on X/Z report.
2. Entry which makes the PLU stock counter negative
3. Net Tax 4 total print on X/Z report.
1. Taxable 4
SBTL
2. Gross Tax 4 3. Net Tax 4
and refund
Tax 4
Print
Print
Skip
Skip
Skip
905-A
2. Entry which makes the
PLU stock counter negative
906-A
Allowed unconditionally
0
Operation allowed despite
error massage
1
2
inhibited
2
3
Allowed unconditionally
4
4
Operation allowed despite
error massage
5
inhibited
6
Print
0
Skip
1
Print
Skip
Print
Print
1. Printing of PLU codes
Skip
5
Print
6
Skip
7
★
NO
YES
★
#906-B: 1. Bottle return function
2. Hash setting
#905-B: 1. Tax printing when taxable subtotal is zero.
1. Bottle return function
2. Tax printing when GST is VAT.
3. Tax printing when tax is zero.
1. Taxable
subtotal is
zero
2. Hash setting
906-B
Disable
0
Enable
2
Disable
4
Enable
6
1. Split pricing counting
2. Multiplication entry
906-C
Multiplication
0
Quantity
Successive multiplication
1
Disable
2. GST is VAT 3. Tax is zero
905-B
Print
Skip
Skip
Print
Print
Skip
Print
0
Skip
1
Print
2
Skip
3
Print
4
Enable
★
#906-C: 1. Split pricing counting
2. Multiplication entry
Skip
5
Print
6
Split pricing
2
7
Multiplication
4
Successive multiplication
5
Split pricing
6
Skip
Package
#905-C: 1. GST EXPT print on X/Z report
1. GST EXPT
905-C
Print
0
Skip
4
2. Fractional quantity (3 digit decimal places)
1. Presetting of Consecutive No.
Type 1
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
Type 8
Type 9
Type F
VAT
Tax3 method
GST
VAT
VAT
Add on Tax
Add on Tax
VAT
Add on Tax
Add
on Tax
PST
Tax2, 1
method
(PST)
905-D
Tax on Tax
0
Tax on Base
1
Tax on Tax
2
Tax on Base
3
Tax on Tax
4
Tax on Base
5
Tax on Tax
6
Tax on Base
7
Tax on Tax
8
Tax on Base
9
★
#906-D: 1. Presetting of Consecutive No.
★
#905-D: 1. TAX METHOD
Tax4
method
(GST)
★
Yes
No
★
ER-A410U/A420U
SERVICE (SRV) MODE
1–6
2. Fractional quantity
(3-digit decimal places)
906-D
No
0
Yes
1
No
2
Yes
3
★
[JOB#907] ER-A410: MRS = 0010
ER-A420: MRS = 0010
#908-C: 1. Addition to the hourly total in void mode
2. X1/Z1 report at X2/Z2 mode
#907-A, B: Not used (Fixed at “00”)
3. Resetting of consecutive number in Z1
#907-C: 1. In case of individual and all cashier CCD, X report before
CCD entry
1. Addition to the 2. X1/Z1 report
hourly total in
at X2/Z2
void mode
mode
2. Minus DEPT. / PLU
1. In case of all individual
and all cashier CCD, X
report before CCD
entry
2. Minus DEPT. / PLU
Enable
908-C
No
Enable
907-C
No
Disable
0
Yes
1
No
2
0
Yes
3
Enable
1
No
4
Disable
4
Disable
Disable
3. Resetting of
consecutive
No.in Z1
Enable
★
Enable
Yes
5
Disable
Yes
5
No
6
Yes
7
★
#907-D: 1. CCD compulsory
1. CCD compulsory
907-D
Non compulsory
0
For individual cashier
1
For all cashier
#908-D: 1. Printing X/Z report (Except the individual cashier)
2. GT resetting at Z1 general resetting
★
1. Printing X/Z report
2
Receipt & Journal
[JOB#908] ER-A410: MRS = 0000
ER-A420: MRS = 0000
Journal
2. GT resetting at Z1
908-D
No
0
Yes
1
No
4
Yes
5
★
#908-A: Printing of GT on Z report
GT1 (NET)
GT2 (+)
Print
Print
Skip
Print
Skip
Skip
GT3 (-)
908-A
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
GT3 (-)
908-B
Skip
0
Print
1
Skip
2
Print
3
Skip
4
Print
5
Skip
6
Print
7
[JOB#909] ER-A410: MRS = 2000
ER-A420: MRS = 2000
★
#909-A: 1. Printing of training GT on the X report
2. Printing of training GT on the Z report
1. Printing of training GT
on the X report
NO
YES
#908-B: Printing of GT on X report
GT1 (NET)
GT2 (+)
Skip
Skip
Print
Skip
Print
Print
2. Printing of training GT
on the Z report
909-A
YES
0
NO
1
YES
2
NO
3
★
#909-B: 1. Printing of data on PLU resetting report
1. Printing of data on PLU resetting report
★
Yes
0
No
4
★
#909-C: 1. Printing of void mode & MGR void in Z2 report
2. Printing of void mode & MGR void in Z1 report
1. Printing of void mode & 2. Printing of void mode &
MGR void in Z2 report
MGR void in Z1 report
YES
NO
#909-D: Not used (Fixed at “0”)
ER-A410U/A420U
909-B
SERVICE (SRV) MODE
1–7
909-C
YES
0
NO
2
YES
4
NO
6
★
[JOB#910] ER-A410: MRS = 0204
ER-A420: MRS = 0204
#912-D: 1. LOGO Message control.
1. LOGO Message control
#910-A: Not used (Fixed at “0”)
912-D
3-line header instead of a LOGO
0
★
(ER-A420)
1
★
(ER-A410)
#910-B: 1. Cashier code display
Graphical LOGO only
2. Auto cashier sign off at the end of transaction
1. Cashier code display
Hidden
Appear
2. Auto cashier sign off at
the end of transaction
910-B
No (After cashier Z1 only)
0
Yes (Everytime)
1
No (After cashier Z1 only)
2
Yes (Everytime)
3
★
Graphical LOGO and 3-line footer
2
6-line header
3
Graphical LOGO and 3-line header
4
3-line header and 3-line footer
5
Type :
1
2
LOGO
LOGO
0
3
#910-C: Not used (Fixed at “0”)
Header
#910-D: 1. Cashier system code entry (Fixed at “4”)
[JOB#911] ER-A410: MRS = 0000
ER-A420: MRS = 0000
Footer
#911-A: 1. Fraction treatment
4
1. Fraction treatment
911-A
Round off
0
Round up unit
1
Disregarding
2
5
LOGO
★
#911-B, C, D: Not used (Fixed at “000”)
[JOB#912] ER-A410: MRS = 0061
ER-A420: MRS = 0060
[JOB#913] ER-A410: MRS = 0104
ER-A420: MRS = 0104
#912-A: 1. Date print format
#913-A: 1. Content of total VP amount
Date format
912-A
Month/Day/Year
0
Day/Month/Year
1
Year/Month/Day
2
1. Content of total VP amount
913-A
Total amount
0
Tendered amount
1
★
★
#913-B: 1. Printing of subtotal by ST key
#912-B: 1. Time system
2. Printing of MDSE ST
1. Time system
912-B
12H
0
24H
1
3. Escape the compulsory of VP and SLIP
★
1. Printing of
2. Printing of
subtotal by ST
MDSE ST
key
#912-C: 1. Receipt After transaction format
2. Copy receipt
No
3. Footer print control
1. Receipt After
2. Copy receipt
No
Total only
Yes
No
Detail
Yes
No
3. Footer print
control
Yes
912-C
All receipt
0
On selected function keys at the
time of finalization
1
All receipt
2
On selected function keys at the
time of finalization
3
All receipt
4
On selected function keys at the
time of finalization
5
All receipt
6
On selected function keys at the
time of finalization
7
No
Yes
Yes
3. Escape
compulsory
VP and SLIP
Disable
913-B
0
Enable
1
Disable
2
Enable
3
Disable
4
Enable
5
Disable
6
Enable
7
★
#913-C: 1. Buzzer off 2 sec. after lock error
2. Buffered keyboard
1. Buzzer off 2sec. after
lock error
2-sec. off
★
ER-A410U/A420U
Constant
(Till error recovery)
SERVICE (SRV) MODE
1–8
2. Buffered keyboard
913-C
Yes
0
No
1
Yes
2
No
3
★
#914-D: 1.Manual tax
#913-D: 1. Drawer closing is compulsory
2. Error mode
2. Check cashing
3. Key touch sound
3. Non-add No. entry
1. Drawer
closing
2. Error mode
3. Key touch
sound
All lock error
Non-compulsory
Misoperation
(One shot error)
All lock error
Compulsory
Misoperation
(One shot error)
1. Manual tax 2. Check
cashing
913-D
Enable
0
Disable
1
Enable
2
Disable
3
Enable
4
Disable
5
Enable
6
Disable
7
3. Non-add
No. entry
Disable
Enable
Enable
★
Disable
Disable
Enable
[JOB#914] ER-A410: MRS = 1100
ER-A420: MRS = 1100
[JOB#915] ER-A410: MRS = 0000
ER-A420: MRS = 0000
#914-A: 1. Receipt issuing at no-sale
#915-A, B: Not used (Fixed at “00”)
2. [NS] key separation from [CA/AT] key for no-sale function
2. [NS] key
separation
3. Tax delete
Inhibit
Enable
Enable
Inhibit
No
Enable
Yes
Disable
No
1
2
Disable
3
Enable
4
Disable
5
Enable
6
Disable
7
915-C
Unlimited
0
Once only
2
★
[JOB#916] ER-A410: MRS = 1400
ER-A420: MRS = 1400
2
3
Inhibit
4
Enable
5
Inhibit
6
Enable
7
★
(ER-A410)
#916-A: 1. Print format when and amount overlaps each other REG
mode
1. Print format when and amount overlaps
each other REG mode
Disable
0
Enable
1
Truncate
0
2 line print
1
★
2. Food stamp subtotal entry before food stamp tender
1. Finalization by charge
when ST is 0 or below
★
#914-C: 1. Void mode
RFND type of sales only
2. Non-add code entry at the beginning of a transaction operation
2. Non-add code entry
916-A
#916-B: 1. Finalization by charge when ST is 0 or below
914-B
Disable
1
Enable
#915-D: Not used (Fixed at “0”)
★
(ER-A420)
1. No-sale after # entry
Enable
Disable
★
0
#914-B: 1. No-sale after NON ADD code entry
1. Void mode
0
1. ST (-), ST (%) as many times needed/operation only once
914-A
Yes
Enable
#915-C: 1. ST (-), ST (%) as many times needed/once only
3. Tax delete
1. Receipt
issuing at
no-sale
914-D
914-C
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
Always
★
ER-A410U/A420U
SERVICE (SRV) MODE
1–9
2. Food stamp subtotal
entry before food stamp
tender
916-B
Non-compulsory
0
Compulsory
1
Non-compulsory
4
Compulsory
5
★
#917-B: 1. Printing of Taxable 2 subtotal on X/Z report
#916-C: 1. Negative merchandise subtotal
2. Subtotal entry compulsory before tendering
2. Printing of Gross Tax 2 and refund Tax 2 total on X/Z report
3. Subtotal entry before direct non-tendering finalization
3. Printing of Net Tax 2 total on X/Z report
1. Negative mer- 2. Subtotal entry 3. Subtotal entry
chandise subcompulsory
before direct
total
before tendernon-tendering
ing finalization
Non-compulsory
Enable
Compulsory
Non-compulsory
Disable
Compulsory
1. Taxable 2
subtotal on
X/Z report
916-C
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
Non-compulsory
4
Compulsory
5
Non-compulsory
6
Compulsory
★
2. Gross Tax 2
and refund
Tax 2 total on
X/Z report
Print
Print
Skip
Print
Skip
Skip
7
3. Net Tax 2
total on X/Z
report
917-B
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
★
#917-C: 1. Printing of Taxable 3 subtotal on X/Z report
#916-D: 1. Coupon PLU printing on X/Z report
2. Net sales subtotal (NET1) printing on X/Z report
2. Printing of Gross Tax 3 and refund Tax 3 total on X/Z report
3. CHECK change total printing on X/Z report
3. Printing of Net Tax 3 total on X/Z report
1. Print coupon 2. Print net sales 3. Print CHK
PLU’s on genSBTL (NET1)
CHANGE on
eral report
on general
general report
report
Print
Print
Skip
Print
Skip
Skip
1. Taxable 3
subtotal on
X/Z report
916-D
Print
0
Skip
1
★
2. Gross Tax 3
and refund
Tax 3 total on
X/Z report
Print
Print
3. Net Tax 3
total on X/Z
report
917-C
Print
0
Skip
1
Print
2
Print
2
Skip
3
Skip
3
Print
4
Print
4
Skip
5
Print
6
Skip
7
Skip
Print
Skip
Skip
Skip
5
Print
6
Skip
7
★
#917-D: 1. Printing of Total Tax amount on X/Z report
[JOB#917] ER-A410: MRS = 0000
ER-A420: MRS = 0000
2. Printing of Gross manual Tax and refund manual Tax on X/Z
3. Printing of Net manual Tax total on X/Z report
#917-A: 1. Printing of Taxable 1 subtotal on X/Z report
1. Total Tax
Amount
2. Printing of Gross Tax 1 and refund Tax 1 total on X/Z report
3. Printing of Net Tax 1 total on X/Z report
1. Taxable 1
subtotal on
X/Z report
2. Gross Tax 1
and refund
Tax 1 total on
X/Z report
Print
Print
Skip
Print
Skip
Skip
3. Net Tax 1
total on X/Z
report
2. Gross manual Tax and
Refund manual Tax on
X/Z report
917-A
Print
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
Print
★
Skip
Print
Skip
Skip
ER-A410U/A420U
SERVICE (SRV) MODE
1 – 10
3. Net manual
Tax total on
X/Z report
917-D
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
★
[JOB#918] ER-A410: MRS = 2000
ER-A420: MRS = 2000
[JOB#922] ER-A410: MRS = 0000
ER-A420: MRS = 0000
#918-A: 1. Printing the text of a tied PLU in set PLU
#922-A: Not used (Fixed at “0”)
#922-B: 1. Using new coin dispenser which can treat $1 coins
2. Direct non-tendering finalization after previous tender enter
1. Printing the text of a
tied PLU in set PLU
2. Direct non-tendering
finalization after previous tender enter
Disable
YES
NO
1. Using new coin dispenser which can treat
$1 coins
918-A
0
Enable
2
Disable
4
Enable
6
918-B
Enable
0
Disable
1
No
0
Yes
1
#922-C, D: Not used (Fixed at “00”)
[JOB#923] NOT USED ER-A410: MRS = 0000
ER-A420: MRS = 0000
[JOB#924] NOT USED ER-A410: MRS = 0000
ER-A420: MRS = 0000
★
#918-C, D: Not used (Fixed at “00”)
[JOB#925] NOT USED ER-A410: MRS = 0000
ER-A420: MRS = 0000
[JOB#919] ER-A410: MRS = 0400
ER-A420: MRS = 0400
[JOB#926] ER-A410: MRS = 0400
ER-A420: MRS = 0400
#919-A: Not used (Fixed at “0”)
#926-A: Not used (Fixed at “0”)
#919-B: 1. Checking of casher # on guest check when a reorder is
made
#926-B: 1. Program reset at PGM2 mode
1. Program reset at PGM2 mode
926-B
Disable
0
Enable
4
2. Guest check No.
1. Checking of casher #
on guest check when a
reorder is made
YES
NO
2. Guest check No.
#926-C, D: Not used (Fixed at “00”)
Auto generation
0
Manual
1
Auto generation
4
Manual
5
[JOB#927] NOT USED ER-A410: MRS = 0000
ER-A420: MRS = 0000
★
[JOB#928] ER-A410: MRS = 0000
ER-A420: MRS = 0000
#928-A: 1. Printing of slip LOGO text
2. Amount printing when PLU unit price is 0
2. Amount printing when
PLU unit price is 0
Non-compulsory
Compulsory
1. Printing of slip LOGO text
928-A
No
0
Yes
1
919-C
No
0
Yes
1
No
2
Yes
3
★
2. Header line on slip paper when a reorder is made printed
1. VP message printing
on slip
2. Foreign currency format
2. Foreign currency
Not
Yes
No
Check only
919-D
0
Omit digits lower than
TAB position
1
Not
4
Omit digits lower than
TAB position
5
★
#928-B: 1. VP message printing on slip
#919-D: 1. Conversion SBTL printing of native SBTL
1. Conversion SBTL print
of native SBTL
★
919-B
#919-C: 1. PBLU entry
1. PBLU entry
★
★
#918-B: 1. Fractional entries for non-scalable PLU/DEPT.
1. Fractional entries for non-scalable PLU/DEPT.
922-B
★
Check & Credit
2. Header line on slip
paper when a reorder is
made printed
928-B
Printed
0
Not
1
Printed
2
Not
3
★
#928-C: 1. Printing of PLU on slip when it is $0.00
2. Printing the text of a tied PLU of a set PLU on slip
1. Printing of PLU on slip
when it is $0.00
[JOB#920] NOT USED ER-A410: MRS = 0000
ER-A420: MRS = 0000
YES
[JOB#921] NOT USED ER-A410: MRS = 0000
ER-A420: MRS = 0000
NO
ER-A410U/A420U
SERVICE (SRV) MODE
1 – 11
2. Printing the text of a
tied PLU on slip
928-C
YES
0
NO
2
YES
4
NO
6
★
[JOB#930~939] ER-A410: MRS = 0000
ER-A420: MRS = 0000
#928-D: 1. Printing of PB/NBAL on slip
2. Compulsory slip print system
RESET REPORT COUNTER
1. Printing of PB/NBAL on 2. Compulsory slip print
slip
system
YES
NO
928-D
According to each media’s
preset (Slip printing at
[FINAL] in PBLU system
isn’t always compulsory.)
0
Compulsory for every entry
1
Compulsory for PB
2
According to each media’s
preset (Slip printing at
[FINAL] in PBLU system
isn’t always compulsory.)
4
Compulsory for every entry
Compulsory for PB
"0"
Job#
@/FOR
Initial value of Z counter
JOB #
Function
930
Z1 report counter
933
Hourly Z1 report counter
934
PLU Z1 report counter
935
Cashier Z1 report counter
936
PBLU Z1 report counter
5
937
Z2 report counter
6
939
Daily net Z2 report counter
[JOB#929] ER-A410: MRS = 0000
ER-A420: MRS = 0000
[JOB#942, 943, 969] ER-A410: MRS = 0000000000000
ER-A420: MRS = 0000000000000
#929-A, B, C: Not Used (Fixed at “000”)
GT COUNTER PRESETTING
#929-D: 1. Taxable status assignment method of PLU items
0
1. Taxable status assignment method of PLU
items
929-D
According to its associated department
0
Non taxable
2
Job#
JOB #
#980-A: 1. Stock function
1. Stock function
980-A
Disable
0
Enable
1
CA/AT
Function
942
GT2 (Positive GT)
943
GT3 (Negative GT)
969
Training GT
Note: GT1 is obtained by calculation
Equation: GT1=GT2-GT3
★
[JOB#944] ER-A410: MRS = 0000
ER-A420: MRS = 0000
#980-B: 1. Hash department effect hourly sales total
1. Hash department effect hourly sales total
980-B
No
0
Yes
1
PGM2 mode secret code presetting
★
0
944
@/FOR
XXXX
CA/AT
4 digits
#980-C: Not used (Fixed at “0”)
#980-D: 1. RCPT key separation from RCPT/PO key
Note: When the secret code “0” is programmed, the secret code entry
is inhibited.
2. PLU PRICE 2 is enabled
2. PLU PRICE 2 is
effective
[JOB#948] ER-A410: MRS = 00
ER-A420: MRS = 00
980-D
Yes
0
★
(ER-A420)
No
1
★
(ER-A410)
Yes
2
No
3
No
Yes
0000000000000
13 digits
@/FOR
★
[JOB#980] ER-A410: MRS = 0000
ER-A420: MRS = 0001
1. RCPT key separation from RCPT/PO
key
CA/AT
XXXX
★
PROGRAMMING OF THE TRAINING CASHIER NO.
0
948
@/FOR
XX
CA/AT
XX: Cashier No.
[JOB#949] ER-A410: MRS = “**TRAINING**”
ER-A420: MRS = “**TRAINING**”
THE TRAINING MODE’S TITLE
Space
949
ER-A410U/A420U
SERVICE (SRV) MODE
1 – 12
@/FOR
Character Key
(12 chara. )
CA/AT
[JOB#950] MRS = STANDARD KEY LAYOUT
No.
Free key layout (Except for department keys and direct PLU keys.)
KEY
KEY TEXT
(8 Char.)
25
L2
L2
Initial setting
Key number manual
increment
26
L3
L3
27
PRICE SHIFT
P. SFT
Key number automatic
increment
28
TAX1 SHIFT
TAX1SF
29
TAX2 SHIFT
TAX2SF
30
TAX3 SHIFT
TAX3SF
@/FOR
31
TAX4 SHIFT
TAX4SF
To inhibit
32
FS SHIFT
FS SFT
SBTL
33
PRINT
PRINT
Increment Key No.
34
SLIP
SLIP
35
VOID
VOID
36
REFUND SALES
RFND
37
%1
%1
38
%2
%2
39
%3
%3
Key number manual increment
40
%4
%4
Key number automatic
increment
41
(–) 1
(–) 1
42
(–) 2
(–) 2
43
(–) 3
(–) 3
44
(–) 4
(–) 4
45
TAX
TAX
46
AUTO
AUTO
47
AUTO2
AUTO2
XXX: 1 to 119
999 (for inhibit key)
48
AUTO3
AUTO3
49
AUTO4
AUTO4
• The Key No. is assigned to each key which is supposed to be dept.
or direct PLU key by depressing the key after entering the key No.
50
AUTO5
AUTO5
51
CASH2
CA2
52
CHECK
CHECK
53
CHECK2
CHECK2
54
CH1
CH1
55
CH2
CH2
56
CH3
CH3
57
CH4
CH4
58
CH5
CH5
KEY
59
CONV1
CONV1
KEY
60
CONV2
CONV2
KEY
61
CONV3
CONV3
KEY
62
CONV4
CONV4
KEY
63
PBLU
PBLU
KEY
64
NEW CHECK
N. C.
SERVICE
SRVC
950
XXX
@/FOR
Free key
Key No.
CA/AT
XXX: 1 to 79
999 (for inhibit key)
[JOB#951] MRS = STANDARD KEY LAYOUT
Free key layout (department keys and direct PLU keys)
@/FOR
951
XXX
Free key
CA/AT
Key No.
@/FOR
To inhibit
SBTL
Increment Key No.
• Those keys programmed by this job No. will be dept. keys if dept.
code is assigned, and will be direct PLU keys if PLU code is assigned
in the PGM2 mode.
FUNCTION KEY LISTKEY
No.
1
2
3
4
5
6
KEY
0 KEY
1 KEY
2 KEY
3 KEY
4 KEY
5 KEY
KEY TEXT
(8 Char.)
0
1
2
3
4
5
7
6 KEY
6
KEY
65
8
7 KEY
7
KEY
66
FINAL
FINAL
KEY
67
DEPOSIT
DEPO
KEY
68
DEPOSIT RFND
DEP. RF
00 KEY
69
FS TEND
FSTEND
000KEY
70
RA
RA
.
71
RA2
RA 2
CLEAR
72
RCPT/PO
RCP/PO
@/FOR
73
PO2
PO 2
CASHIER NO.
CASH#
BIRTH
9
10
11
12
13
14
15
8 KEY
9 KEY
00 KEY
000KEY
DECIMAL POINT
CLEAR
@/FOR
8
9
KEY
16
SUB TOTAL
SBTL
74
17
CA/AT
CA/AT
75
BIRTHDAY
MDS ST
76
DEPT. NO.
DEPT#
SCALE
SCALE
18
MDSE SBTL
19
TRAY ST
TRY ST
77
20
#/TM
#/TM
78
OPENTARE
OPN TR
NS
79
RCPT
RCPT
999
INHIBIT
21
NO SALE
22
PLU/SUB
PLU/SB
23
REFUND SALES
RF SAL
24
L1
L1
ER-A410U/A420U
SERVICE (SRV) MODE
1 – 13
ER-A410/A420 KEYBOARD KEY POSITIONS
[Signal connection chart]
25PIN D-SUB
ECR
9PIN D-SUB
SD
2
3
SD
RD
3
2
RD
RTS
4
7
RTS
DCD
8
1
DCD
DTR
20
4
DTR
DSR
6
6
DSR
CTS
5
8
CTS
SG
7
5
SG
FG
1
FRAME GROUND is connected to
the shield of the cable.
ECR
9PIN D-SUB
ECR
9PIN D-SUB
ER-A410
16
22
28
34
40
46
52
58
64
70
76
82
RECEIPT JOURNAL
05
10
15
21
27
33
39
45
51
57
63
69
75
81
04
09
14
20
26
32
38
44
50
56
62
68
74
80
03
08
13
19
25
31
37
43
49
55
61
67
73
79
02
07
12
18
24
30
36
42
48
54
60
66
72
78
01
06
11
17
23
29
35
41
47
53
59
65
71
77
:FIXED KEY (CAN NOT CHANGE)
ER-A420
RECEIPT JOURNAL
07
14
21
28
35
42
49
56
63
70
77
84
91
98
105
112
119
06
13
20
27
34
41
48
55
62
69
76
83
90
97
104
111
118
05
12
19
26
33
40
47
54
61
68
75
82
89
96
103
110
117
04
11
18
25
32
39
46
53
60
67
74
81
88
95
102
109
116
03
10
17
24
31
38
45
52
59
66
73
80
87
94
101
108
115
02
09
16
23
30
37
44
51
58
65
72
79
86
93
100
107
114
01
08
15
22
29
36
43
50
57
64
71
78
85
92
99
106
113
:FIXED KEY (CAN NOT CHANGE)
[JOB#975] MAX. Number programming
975
@/FOR
@/FOR
X
X
MAX. Number of Departments
1
YYYY
ER-A410 = 20,
ER-A420 = 10
2
0-1800 (6 digit)
MAX. Number of PBLU Records
3
0-999 (3 digit)
50
MAX. Number of Cashiers
4
1-20 (2 digit)
20
• Sending ECR RAM data
SSP only
0
CA/AT
• Receiving ECR RAM data
998
@/FOR
SD
RD
2
2
RD
RTS
7
7
RTS
DCD
1
1
DCD
DTR
4
4
DTR
DSR
6
6
DSR
CTS
8
8
CTS
SG
5
5
SG
500
[JOB#996, 998] RAM DATA BACKUP function
(ECR 0 ECR; 02FD.exe Protocol)
@/FOR
3
MRS
MAX. Number of PLU Records
996
3
CA/AT
YYYY
1-99 (2 digit)
SD
CA/AT
SD:
RD:
DTR:
DSR:
RTS:
DCD:
CTS:
FG:
*The Baud-rate is determined by SRV#903-A. The auto baud-rate
function is not available in this model.
ER-A410U/A420U
TRANSMITTED DATA
RECEIVED DATA
DATA TERMINAL READY
DATA SET READY
REQUEST TO SEND
DATA CARRIER DETECTOR
CLEAR TO SEND
FRAME GROUND
SERVICE (SRV) MODE
1 – 14
[JOB#985]
Display during transmission
Euro symbol programming for TM-295
SRV
996
TEXT, MODE
JOB#, PACKET NO.
0
985
SRV
998
@/FOR
CA/AT
A
X: 0 = Space
TEXT, MODE
JOB#, PACKET NO.
1 = Euro symbol
MRS = 0 (Space)
At the end of the job, one of the following messages is printed.
[JOB#986] ER-A410: MRS = “ $”
ER-A420: MRS = “ $”
• Normal termination of a send operation
Domestic currency symbol programming
#996 SEND OK
JOB#, ERROR MESSAGE
Space
@/FOR
986
• Communication Error in a send operation
#996 COM. ERROR
01 JOB#, ERROR, MESSAGE,
ERROR CODE
This symbol is printed with (+) amount of domestic currency. The programmed characters is printed at the left side of amount.
JOB#, ERROR MESSAGE
Ex)
Case of “US$”:
DEPT.01 US$1.00
• Normal termination of a receive operation
#998 RECEIVE OK
CA/AT
Characters can be entered by using the character keys or numeric
keys.
• Time-out in a send operation
#996 TIME OUT
Character Key
(4 chara.)
JOB#, ERROR MESSAGE
Programmed symbol
• Communication Error in a receive operation
#998 COM. ERROR
If some space characters are programmed at the left side of symbol
(ex. “ $”), they are not counted as the number of character of the currency symbol.
01 JOB#, ERROR MESSAGE,
ERROR CODE
Ex)
• Data format Error in a receive operation
#998 DATA ERROR
In the case of “ US$”: (The currency symbol means “US$”)
DEPARTMENT01 US$10.00
15 JOB#, ERROR MESSAGE,
ERROR CODE
Programmed symbol
• Time-out in a receive operation
#998 TIME OUT
JOB#, ERROR MESSAGE
[JOB#987] ER-A410: MRS = 0
ER-A420: MRS = 0
Text Changing (To Default text)
*All error message are fixed.
0
*ERROR CODE:
987
@/FOR
X
CA/AT
01 = ID No. error (ID No. in IDENQ is not correct.)
X: 0 = English text
02 = Parity error
2 = French text
03 = Check sum error
04 = Data size error
When this job is executed, the following data is affected.
05 = Hardware error
(a) Function text
06 = Power off error
(b) Cashier text
07 = Time out error
(c) Each message text (LOGO, etc..)
08 = DSR off error
11 = Transmit data size error
[JOB#989]
12 = Block sequence error (Irregular sequence No. has been
received.)
Resetting of all counters and totalizers
989
13 = NAK code error (NAK code has been received.)
@/FOR
CA/AT
*All counters, totalizers, and Z counters are initialized.
The GT1-GT3 memories are initialized.
15 = ECR TYPE error (Models of two ECR is different.)
*The following print is only on the journal.
#989
ER-A410U/A420U
SERVICE (SRV) MODE
1 – 15
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE
1. READING OF THE PGM MODE PROGRAMS
[JOB#1100] : DEPARTMENT PRESET READING
[JOB#2119] : DIRECT KEY PRESET READING
key operation
Key operation
All
2119
Single item
1100
@/FOR
XX
Start No.
@/FOR
XX
@/FOR
CA/AT
End No.
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2–1
CA/AT
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2–2
[JOB#1200] : PLU PRESET READING
Key operation
All
Single item
1200
@/FOR
XXXXXX
Start No.
@/FOR
XXXXXX
CA/AT
End No.
[JOB#2220] : LINK PLU PRESET READING
Key operation
All
Single item
2220
ER-A410U/A420U
@/FOR
PROGRAM (PGM2/PGM1) MODE
2–3
XXXXXX
Start No.
@/FOR
XXXXXX
End No.
CA/AT
[JOB#2221] : SET PLU PRESET READING
[JOB#1300] : FUNCTION PRESET READING
Key operation
Key operation
2221
@/FOR
CA/AT
1300
@/FOR
[JOB#2225] : MIX & MATCH PRESET READING
Key operation
2225
@/FOR
CA/AT
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2–4
CA/AT
[JOB#1500] : CASHIER PRESET READING
Key operation
1500
ER-A410U/A420U
@/FOR
PROGRAM (PGM2/PGM1) MODE
2–5
CA/AT
[JOB#2600] : OTHER PROGRAM PRESET READING
[JOB#2700] : TAX PRESET READING
Key operation
2700
2600
@/FOR
@/FOR
CA/AT
CA/AT
[JOB#2640] : SLIP TEXT PROGRAMMING READING
Key operation
2640
@/FOR
[JOB#2800] : PBLU CODE READING
CA/AT
2800
ER-A410U/A420U
@/FOR
PROGRAM (PGM2/PGM1) MODE
2–6
CA/AT
[JOB#2900] : AUTO KEY PRESET READING
[JOB#6110] : ONLINE PROGRAMMING READING
Key operation
Key operation
2900
@/FOR
6110
CA/AT
@/FOR
CA/AT
[JOB#2990] : THERMAL PRINTER PRESET REPORT
[JOB#7110] : CAT PROGRAMMING READING REP.
Key operation
2990
@/FOR
CA/AT
7110
ER-A410U/A420U
@/FOR
PROGRAM (PGM2/PGM1) MODE
2–7
CA/AT
2. PROGRAMMING
[JOB#1110]
[JOB#2111]
PROGRAMMING OF DEPT. PRICE
DEPT. TAX STATUS PROGRAMMING
@/FOR
1110
@/FOR
2111
0
0
@/FOR
XX
DEPT. CODE
YYYYYY
price
SBTL
CA/AT
XX
For next code
@/FOR
ABCDEF
SBTL
CA/AT
SBTL
CA/AT
DEPT. CODE
For next DEPT
XX: DEPT-CODE = 01~Max number of DEPT.
YYYYYY: PRICE = 0~999999
XX: DEPT. CODE = 01~Max number of DEPT.
If a price is set for a department which amount entry type is “INHIBIT” or
“OPEN”, its amount entry type is set as below automatically.
1 “INHIBIT”
“PRESET”
A: Sign
A
+
0
–
1
“OPEN&PRESET” 1 “OPEN”
B: Food stamp
MRS = 000000
[JOB#2110]
B
Non-food stampable
0
Food stampable
1
PROGRAMMING OF DEPT. FUNCTIONS
C: Taxable 4
@/FOR
2110
0
XX
@/FOR
ABCDEF
SBTL
CA/AT
C
Non taxable
0
Taxable
1
DEPT. CODE
D: Taxable 3
For next code
XX: DEPT. code = 01~Max number of DEPT.
A: Item validation printing
0
Compulsory
1
Non
Table No.
Taxable
1
E: Taxable 2
E
Non taxable
0
Taxable
1
B
F: Taxable 1
0
1 to 9
C: Scale entry
C
Inhibit
0
Enable
1
Compulsory
2
D: SICS Function
0
A
Non compulsory
B: Tare table No.
D
Non taxable
0
Single item cash sale
1
Single item finalize
2
0
Taxable
1
MRS = 000000
[JOB#2112]
DEPT. HALO (limit) preset
D
Normal
F
Non taxable
2112
@/FOR
0
XX
@/FOR
AB
DEPT. CODE
E: Dept. type
E
Normal
0
Hash
1
Bottle Return
2
F: Amount entry type
For next DEPT
XX: DEPT. CODE = 01~Max number of DEPT.
A: Mantissa (HALO) = 0~9
B: Exponent (HALO) = 0~7
F
Inhibited
0
Open
1
*Items A and B indicate A u 10B. Any amount below that value is
enable within 99999999.
Preset
2
MRS = 17
Open and preset
3
MRS = 000001
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2–8
[JOB#2114]
[JOB#2180]
DEPT. TEXT PROGRAMMING
DEPARTMENT LOWER LIMITATION AGE PROGRAMMING
@/FOR
2114
@/FOR
XX
Character key
@/FOR
2180
No change
SBTL
0
CA/AT
DEPT. CODE
@/FOR
XX
For next code
SBTL
YY
CA/AT
DEPT. code
For next code
XX: DEPT. CODE = 01~Max number of DEPT.
Characters: Max. 16Characters
XX: Department code (01 to Max. number of departments.)
Characters can be entered by using character keys or numeric keys.
The key entry sequence for entering one character by the numeric keys
is as follows.
YY: Age (00 to 99) 00 = No limitation
MRS = 00
XXX 3 00 KEY
[JOB#1200]
XXX: CHARACTER CODE (3 DIGITS)
PROGRAMMING OF PLU ITEMS TO BE ASSOCIATED TO DEPARTMENTS.
MRS = DPT. X_X_
@/FOR
1200
[JOB#2115]
0
COMMISSION GROUP PROGRAMMING
2115
XXXXXX
@/FOR
@/FOR
SBTL
YY
CA/AT
PLU code
0
For next code
XX
@/FOR
A
SBTL
CA/AT
DEPT. CODE
XXXXXX: PLU code = 1~999999
For next code
YY: DEPT. code = 01~Max number of DEPT.
XX: DEPT. CODE = 01~Max number of DEPT.
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in PLU file.
A: Group No. = 0~9
MRS = 0
MRS = 01
[JOB#2116]
[JOB#1210]
PROGRAMMING OF DEPT. GROUPS
2116
PLU UNIT PRICE PROGRAMMING
@/FOR
0
@/FOR
1210
XX
@/FOR
A
SBTL
CA/AT
DEPT. CODE
For next code
0
XXXXXX
@/FOR
XX: DEPT. code = 01~Max number of DEPT.
0
SBTL
YYYYYY
PRICE1
YYYYYY
PRICE2
SBTL
CL
A: Group No. = 0 ~ 9
Code increment
MRS = 0
Code entry
[JOB#2119]
CA/AT
DIRECT KEY DEFINITION FOR DEPT. KEYS
2119
@/FOR
XXXXXX: PLU CODE = 1~999999
YYYYYY: Amount = 0~999999
inhibit
XXX
@/FOR
YY
SBTL
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in PLU file.
CA/AT
KEY No.
For next code
If a price is set for a department which the amount entry type is “INHIBIT”
or “OPEN”, the amount entry type is set as below automatically.
The DEPT. code is assigned to the key no. which has been programmed in the JOB#951 programming.
“PRESET”
1 “INHIBIT”
“OPEN&PRESET” 1 “OPEN”
XXX: Key No.
YY: DEPT. CODE
MRS = 0
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2–9
[JOB#1211]
[JOB#2210]
PLU BASE Q’TY PROGRAMMING
PLU FUNCTION PROGRAMMING
@/FOR
1211
XXXXXX
@/FOR
ZZ
@/FOR
2210
0
SBTL
0
CA/AT
PLU code
XXXXXX
For next code
@/FOR
ABC
SBTL
CA/AT
PLU code
For next code
XXXXXX: PLU code = 1~999999
ZZ: Base quantity = 00~99
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
XXXXXX: PLU code = 1~999999
A: Tare table No.
MRS = 00
A
Non
[JOB#1220]
0
Table No.
1 to 9
PROGRAMMING PLU STOCK (ADD)
1220
B: Scale entry
@/FOR
B
Inhibited
XXXXXX
@/FOR
YYYYYYY
SBTL
CA/AT
PLU code
0
Enable
1
Complusory
2
Amount entry type
C
Inhibited
0
Open
1
Preset
2
For next code
C:
XXXXXX: PLU code (1 to 999999)
YYYYYYY: STOCK VALUE = 1 to 9999999
The stock value entered is added to the PLU stock counter.
MRS = 0
[JOB#1221]
3
Delete
4
If the record of entered the PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
PROGRAMMING PLU STOCK (SUB)
1221
Open and preset
MRS = 002
@/FOR
[JOB#2211]
XXXXXX
@/FOR
YYYYYYY
SBTL
CA/AT
PLU TAX STATUS PROGRAMMING
PLU code
@/FOR
2211
For next code
0
XXXXXX: PLU code (1 to 999999)
XXXXXX
YYYYYYY: STOCK VALUE = 1 to 9999999
@/FOR
ABCDEF
PLU code
The stock value entered is subtracted from the PLU stock counter.
For next code
MRS = 0
XXXXXX: PLU code = 1~999999
[JOB#1222]
A:
PROGRAMMING PLU STOCK (OVERWRITE)
1222
@/FOR
0
XXXXXX
@/FOR
YYYYYYY
SBTL
Sign
A
+
0
−
1
B: Food stampable
CA/AT
PLU code
For next code
C:
XXXXXX: PLU code (1 to 999999)
YYYYYYY: STOCK VALUE = 0 to 9999999
The stock value entered is overwrites the PLU stock counter.
No
0
Yes
1
Taxable 4
C
Non taxable
0
Taxable
1
MRS = 0
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 10
B
SBTL
CA/AT
D:
E:
F:
Taxable 3
D
[JOB#2217]
Non taxable
0
PLU MIX & MATCH TABLE NO. ASSIGNMENT PROGRAMMING
Taxable
1
Taxable 2
E
Non taxable
0
Taxable
1
Taxable 1
F
Non taxable
0
Taxable
1
@/FOR
2217
No change
XXXXXX
@/FOR
ZZ
SBTL
CA/AT
XXXXXX: PLU code (1 to 999999)
ZZ: Mix & Match table No. (00 to 10)
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
MRS = 000000
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
MRS = 00
[JOB#2280]
PLU LOWER LIMITATION AGE PROGRAMMING
[JOB#2214]
PLU TEXT PROGRAMMING
@/FOR
2280
0
@/FOR
2214
XXXXXX
PLU code
No change
XXXXXX
@/FOR
Character key
SBTL
@/FOR
CA/AT
YY
SBTL
CA/AT
For next code
PLU code
For next code
XXXXXX: PLU code (01 to 999999 max.)
YY: Age (00 to 99) 00 = No Limitation
XXXXXX: PLU code (1 to 999999)
MRS = 0
Characters: MAX. 16Characters
Characters can be entered by using character keys or numeric keys.
The key entry sequence for entering one character by numeric keys is
as follows:
XXX 3 00 KEY
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
[JOB#2219]
DIRECT KEY DEFINITION FOR PLU KEYS
XXX: CHARACTER CODE (3 DIGITS)
2219
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
@/FOR
MRS = PLXXXXXX
Inhibit
L1
[JOB#2215]
L2
COMMISSION GROUP PROGRAMMING
L3
*First time
@/FOR
2215
XX
@/FOR
Key No.
YYYYYY
PLU No.
For next code
= LEVEL1
The others = Same as previous level
0
XXXXXX
@/FOR
A
SBTL
XX: Key No. (Assigned by SRV#951)
CA/AT
YYYYYY: PLU No. (1-999999)
PLU code
For next code
MRS = STANDARD KEY LAYOUT
XXXXXX: PLU code = 1 ~ 999999
A: Group No. = 0 ~ 9
If the record of the entered PLU code is not in the PLU file at this programming, the PLU code will be created in the PLU file.
MRS = 0
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 11
SBTL
CA/AT
[JOB#2220]
[JOB#2230]
LINKED PLU PROGRAMMING
PLU CODE PROGRAMMING (range)
@/FOR
2230
@/FOR
2220
@/FOR
XXXXXX
PLU code
Change to the data
of start PLU
Delete or skip
@/FOR
XXXXXX
PLU code
YYYYYY
YYYYYY
PLU code
SBTL
CA/AT
@/FOR
ZZ
SBTL
CA/AT
Max. 5 times
XXXXXX: Start PLU code = 1~999999
YYYYYY: End PLU code = 1~999999
XXXXXX: PLU code = 1~999999 max.
ZZ: Dept. code = 1~Max number of DEPT.
YYYYYY: PLU code = 1~999999 max.
The parent PLU code should already be defined when the code is
entered in this programming.
Only PLU records which exist in the PLU file will change the data in the
entered range of PLU codes.
[JOB#2231]
MRS = 0
PLU FUNCTION PROGRAMMING (range)
[JOB#2221]
@/FOR
2231
SET PLU PROGRAMMING
XXXXXX
PLU code
Delete or skip
@/FOR
XXXXXX
YYYYYY
Change to the data
of start PLU
@/FOR
2221
@/FOR
YYYYYY
@/FOR
SBTL
ABC
SBTL
CA/AT
CA/AT
XXXXXX: Start PLU code = 1~999999
Max. 5 times
YYYYYY: End PLU code = 1~999999
A: Tare table No.
XXXXXX: Parent PLU code (1 to 999999 max.)
Non
YYYYYY: Tied PLU code (1 to 999999 max.)
Table No.
The PLU code should already be defined when the code is entered in
this programming.
B: Scale entry
C
0
1 to 9
B
MRS = 0
Inhibit
0
*Linked PLU/Set PLU Programming entry:
When the “SBTL” key is pressed without entering any number as the
first PLU code (YYYYYY), the previous data is cleared.
When the “SBTL” key is pressed without entering any number after
the 2nd PLU code (YYYYYY), the programming for the current LINK
PLU is finalized and the programming for the next LINK PLU is
started.
When the “SBTL” key is pressed after entering the maximum PLU
code (YYYYYY), the programming for the current LINK PLU is finalized and the programming for the next LINK PLU is started.
Enable
1
Compulsory
2
Amount entry type
C
Inhibited
0
Open
1
Preset
2
Open and preset
3
Delete
4
[JOB#2225]
C:
This programming job only changes the data of the PLU records that
exist within the PLU file prior to entry.
MIX & MATCH TABLE PROGRAMMING
@/FOR
2225
Delete
XX
Table No.
@/FOR
ZZYYYYYY
SBTL
CA/AT
XX: Table No. (01 to 10)
ZZ: Matching count (1 to 99)
YYYYYY: Adjust amount (1 to 999999)
MRS = nothing
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 12
[JOB#2232]
[JOB#2236]
PLU TAX STATUS PROGRAMMING (RANGE)
PLU LOWER LIMITATION AGE PROGRAMMING (RANGE)
@/FOR
2232
@/FOR
XXXXXX
PLU code
@/FOR
2236
YYYYYY
@/FOR
XXXXXX
Change to the data
of start PLU
Change to the data
of start PLU
@/FOR
ABCDEF
SBTL
@/FOR
CA/AT
YY
XXXXXX: Start PLU code = 1~999999
XXXXXX: Start PLU code (1 to 999999)
YYYYYY: End PLU code = 1~999999
YYYYYY: End PLU code (1 to 999999)
A:
Sign
A
+
0
−
1
YYYYYY
SBTL
CA/AT
YY: Age (00 to 99) 00 = No Limitation
This programming job only changes the data of the PLU records that
exist within the PLU file prior to entry.
[JOB#1310]
B: Food stampable
C:
D:
E:
B
No
0
Yes
1
Taxable 4
C
Non taxable
0
Taxable
1
Taxable 3
D
Non taxable
0
Taxable
1
Taxable 2
E
Non taxable
0
Taxable
1
Taxable 1
F
RATE PROGRAMMING
@/FOR
1310
0
@/FOR
XXX
Function No.
Rate or Price
SBTL
CA/AT
XXX: Function No.
(Rate or Price)
YYYYYY: Price for (−)
YYY.YY: Rate for %
YYYY.YYYY: Rate for conversion
YY.YYY Rate for commission
F:
Function
No.
Function
1
(−) 1
2
(−) 2
3
(−) 3
[JOB#2235]
4
(−) 4
COMMISSION GROUP PROGRAMMING (RANGE)
5
%1
6
%2
7
%3
8
%4
71
Conversion 1
72
Conversion 2
Non taxable
0
Taxable
1
This programming job only changes the data of the PLU records that
exist within the PLU file prior to entry.
2235
@/FOR
XXXXXX
PLU code
@/FOR
YYYYYY
Change to the data
of start PLU
@/FOR
A
SBTL
CA/AT
73
Conversion 3
XXXXXX: Start PLU code = 1~999999
109
Commission 1
YYYYYY: End PLU code = 1~999999
110
Commission 2
111
Commission 3
112
Commission 4
113
Commission 5
114
Commission 6
115
Commission 7
116
Commission 8
117
Commission 9
A: Group No. = 0~9
This programming job only changes the data of the PLU records that
entered range of PLU code.
MRS = 0
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 13
Entry range
Remarks
0 to 999999
unit price
0 to 100.00
% rate
0 to 9999.9999
Rate
0 to 999.99
Rate
[JOB#2310]
C:
% FUNCTION PROGRAMMING
@/FOR
2310
D:
0
@/FOR
XXX
Function No.
A
SBTL
X: Function No.
Function
5
%1
6
%2
7
%3
8
%4
C
Non taxable
0
Taxable
1
Taxable 3
D
Non taxable
0
Taxable
1
Taxable 2
E
Non taxable
0
Taxable
1
Taxable 1
F
Non taxable
0
Taxable
1
CA/AT
E:
Function No.
Taxable 4
F:
MRS = 100000
[JOB#2312, 2322]
A: Amount entry type
Amount entry type
HALO PROGRAMMING
(2312: Function key, 2322: Media key)
A
Inhibit
0
Open
1
Preset
2
Open and preset
3
2312
2322
0
XXX
MRS = 3
@/FOR
AB
SBTL
CA/AT
Function No.
[JOB#2311]
XXX: Function No.
MISCELLANEOUS KEY PROGRAMMING 1
A: Mantissa (0 to 9)
B: Exponent (0 to 7) for (–) and Tax
(0 to 8) for RA/PO and each media
@/FOR
2311
JOB#
0
@/FOR
XXX
Function No.
ABCDEF
SBTL
CA/AT
XXX: Function No.
2312
Function
No.
Function
1
(−) 1
2
(−) 2
3
(−) 3
4
(−) 4
32
MTAX
Function
64
RA
1
(−) 1
65
RA2
2
(−) 2
66
PO
3
(−) 3
67
PO2
4
(−) 4
61
CA1
5
%1
62
CA2
6
%2
76
CH1
7
%3
78
CH2
8
%4
80
CH3
82
CH4
Function No.
A:
@/FOR
2322
Sign
A
84
CH5
+
0
86
CHK1
–
1
87
CHK2
B
Entry range, system: A u 10
No
0
Yes
1
MRS = 17 for (–) and tax
18 for RA/PO and each media.
B: Food stampable
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 14
B
Remarks
Item B is specificable within
the range from 0 to 7
Item B is specificable within
the range from 0 to 8.
Item B is specificable within
the range from 0 to 8.
[JOB#2313]
F-NO.
MISCELLANEOUS KEY PROGRAMMING (% HALO)
@/FOR
2313
0
@/FOR
XXX
YYY.YY
SBTL
CA/AT
XXX: Function No.
YYY. YY: % HALO (0.00 ~ 100.00)
Function No.
Function
5
%1
6
%2
7
%3
8
%4
[JOB#2314]
TEXT PROGRAMMING FOR MISC. KEYS
@/FOR
2314
No change
@/FOR
XXX
Function No.
Character key
SBTL
CA/AT
XXX: Function code
Characters can be entered by using character keys or numeric keys.
The key sequence for entering one character by numeric keys is as follows:
XXX 3 00 key
XXX: CHARACTER CODE (3DIGITS)
Max. 8 Char.
F-NO.
FUNCTION
DEFAULT TEXT
12345678
FUNCTION
DEFAULT TEXT
12345678
20
TAXABLE3 ST
TAX3 ST
21
GROSS TAX3
GRS TAX3
22
REFUND TAX3
RFD TAX3
23
NET TAX3
TAX3
24
EXEMPT TAX3
TX3 EXPT
25
TAXABLE4 ST
TAX4 ST
26
GROSS TAX4
GRS TAX4
27
REFUND TAX4
RFD TAX4
28
NET TAX4
TAX4
29
EXEMPT TAX4
TX4 EXPT
30
GROSS M-TAX
GRS MTAX
31
REFUND M-TAX
RFD MTAX
32
NET M-TAX
M-TAX
33
NON GST SUBTOTAL
GST EXPT
34
PST TOTAL
PST TTL
35
GST TOTAL
GST TTL
36
FS1 FORGIVE
FS TX1
37
FS2 FORGIVE
FS TX2
38
FS3 FORGIVE
FS TX3
39
TOTAL TAX (on Report)
TTL TAX
40
NET
NET
41
NET2
NET2
42
COUPON PLU
CP PLU
43
ITEM VOID
VOID
44
SBTL VOID
SBTL VD
45
MANAGER VOID
MGR VD
46
VOID MODE
VOID
47
REFUND
REFUND
48
HASH VOID
HASH VD
49
HASH REFUND
HASH RF
50
NO SALE
NO SALE
1
(–) 1
(–)
1
51
VP COUNTER
VP CNT
2
(–) 2
(–)
2
52
BILL (SLIP) COUNTER
BILL CNT
DRAWER COUNTER
DRW CNT
3
(–) 3
(–)
3
53
4
(–) 4
(–)
4
54
TRAY TOTAL
TRAY TL
PBAL
***P B A L
5
%1
%1
55
6
%2
%2
56
SERVICE
SERVICE
DEPOSIT
DEPOSIT
7
%3
%3
57
8
%4
%4
58
DEPOSIT REFUND
DPST RF
CUSTOMER (TRANS.COUNT)
TRANS CT
9
NET1
NET1
59
10
TAXABLE1 ST
TAX1 ST
60
NET3 (SALES)
NET3
GRS TAX1
61
CASH
CASH
CASH2
CASH2
11
GROSS TAX1
12
REFUND TAX1
RFD TAX1
62
13
NET TAX1
TAX1
63
FS SALE
FSSALE
RA
***RA
14
EXEMPT TAX1
TX1 EXPT
64
15
TAXABLE2 ST
TAX2 ST
65
RA2
***RA2
PO
***PO
16
GROSS TAX2
GRS TAX2
66
17
REFUND TAX2
RFD TAX2
67
PO2
***PO2
CHECK CASHING
CA/CHK
CHECK CHANGE
CHK/CG
18
NET TAX2
TAX2
68
19
EXEMPT TAX2
TX2 EXPT
69
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 15
F-NO.
FUNCTION
DEFAULT TEXT
12345678
F-NO.
FUNCTION
DEFAULT TEXT
12345678
70
FS CHANGE
FS/CG
120
COMMISSION AMOUNT2
COM.AMT2
71
CONVERSION1
CONV 1
121
COMMISSION AMOUNT3
COM.AMT3
72
CONVERSION2
CONV 2
122
COMMISSION AMOUNT4
COM.AMT4
73
CONVERSION3
CONV 3
123
COMMISSION AMOUNT5
COM.AMT5
74
CONVERSION4
CONV 4
124
COMMISSION AMOUNT6
COM.AMT6
75
FS IN DRAWER
FS/ID
125
COMMISSION AMOUNT7
COM.AMT7
76
GROSS CHARGE1
CHARGE1
126
COMMISSION AMOUNT8
COM.AMT8
77
REFUND CHARGE1
CHARGE1–
127
COMMISSION AMOUNT9
COM.AMT9
78
GROSS CHARGE2
CHARGE2
128
COMMISSION AMOUNT TOTAL
COM.TTL
79
REFUND CHARGE2
CHARGE2–
129
CASH/CHECK IS
CA/CH IS
80
GROSS CHARGE3
CHARGE3
130
CONVERSION1 IS
CONV1 IS
81
REFUND CHARGE3
CHARGE3–
131
CONVERSION2 IS
CONV2 IS
82
GROSS CHARGE4
CHARGE4
132
CONVERSION3 IS
CONV3 IS
83
REFUND CHARGE4
CHARGE4–
133
CCD DIFFER
CCD DIF.
84
GROSS CHARGE5
CHARGE5
134
CCD DIFFER TOTAL
DIF. TL
85
REFUND CHARGE5
CHARGE5–
135
SUBTOTAL
SUBTOTAL
86
CHECK1
CHECK1
136
MDSE SBTL
MDSE ST
87
CHECK2
CHECK2
137
TOTAL
***TOTAL
88
CASH/CHECK IN DRAWER
CA/CH ID
138
CHANGE
CHANGE
89
CASH IN DRAWER
****C ID
139
FS SBTL
FS ST
FS TEND
90
VAT EXEMPT
VAT EXPT
140
FS TEND
91
AVERAGE (HOURLY REPORT)
AVE.
141
FS CHANGE
FS CG
92
GROUP1
G ROUP01
142
ITEMS
ITEMS
93
GROUP2
G ROUP02
143
DEPT. REPORT TITLE
DEPT
94
GROUP3
G ROUP03
144
GROUP REPORT TITLE
GROUP
95
GROUP4
G ROUP04
145
PLU REPORT TITLE
PLU
96
GROUP5
G ROUP05
146
STOCK REPORT TITLE
STOCK
97
GROUP6
G ROUP06
147
ZERO SALES REPORT TITLE
ZERO SAL
98
GROUP7
G ROUP07
148
PRICE CATEGORY REPORT TITLE
CATEGORY
99
GROUP8
G ROUP08
149
TRANS. REPORT TITLE
100
GROUP9
G ROUP09
150
CID REPORT TITLE
TRANS.
C I D
101
PRICE 1 for PLU
LEVEL 1
151
COMMISSION REPORT TITLE
SALES
102
PRICE 2 for PLU
LEVEL 2
152
CCD REPORT TITLE
103
(+) DEPT TOTAL
*DEPT TL
153
CASHIER REPORT TITLE
CASHIER
CCD
104
(–) DEPT TOTAL
DEPT (–)
154
HOURLY REPORT TITLE
HOURLY
105
HASH (+) DPT TOTAL
*HASH TL
155
DAILY NET REPORT TITLE
DAILY
106
HASH (–) DPT TOTAL
HASH (–)
156
PBLU REPORT TITLE
107
BOTTLE (+) TOTAL
*BTTL TL
157
NON ADD CODE TEXT (8chara)
PBLU
#
108
BOTTLE (–) TOTAL
BTTL (–)
158
COPY RCPT TITLE
COPY
109
COMMISSION SALE1
COM.SAL1
159
FINAL
FINAL
110
COMMISSION SALE2
COM.SAL2
160
BALANCE
BALANCE
111
COMMISSION SALE3
COM.SAL3
161
SLIP PRINT MESSAGE on JOURNAL
SLIP PR.
112
COMMISSION SALE4
COM.SAL4
162
SLIP NEXT PAGE
NEXT P.
113
COMMISSION SALE5
COM.SAL5
163
BALANCE FORWARD
BAL FWD
114
COMMISSION SALE6
COM.SAL6
164
TARE WEIGHT
TARE WT.
115
COMMISSION SALE7
COM.SAL7
165
DUE (on DISPLAY)
DUE
116
COMMISSION SALE8
COM.SAL8
166
TAX ST (on DISPLAY)
TAX ST
117
COMMISSION SALE9
COM.SAL9
167
AMOUNT (on DISPLAY)
A M O U NT
118
NON COMMISSION SALE
NON COM.
168
WEIGHT (on DISPLAY)
WEIGHT
119
COMMISSION AMOUNT1
COM.AMT1
169
REFUND TYPE OF SALES (on DISPLAY)
RF SALE
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 16
[JOB#2315]
[JOB#2320]
MISCELLANEOUS KEY PROGRAMMING (%)
MEDIA KEY PROGRAMMING
@/FOR
2315
@/FOR
2320
0
XXX
@/FOR
A
0
SBTL
CA/AT
XXX: Function No.
SBTL
CA/AT
XXX: Function No.
Function No.
Function
5
%1
6
%2
7
%3
8
%4
A:
ABCDEFG
HIJKLMNO
@/FOR
XXX
Function
Function A B C D E F G H
No.
I
J K L M N O
CA1
o o o o o o o o o o o o o o o
62
CA2
o o o o o o o o o o o o o o o
76
CH1
o o o o o o o o o o o o o o o
78
CH2
o o o o o o o o o o o o o o o
CH3
o o o o o o o o o o o o o o o
61
% type
A
80
Subtotal %
0
82
CH4
o o o o o o o o o o o o o o o
1
84
CH5
o o o o o o o o o o o o o o o
86
CHK
o o o o o o o o o o o o o o o
87
CHK2
o o o o o o o o o o o o o o o
Item %
MRS = 0
[JOB#2316]
56
SERVICE u
u u
u u u
u u o u u
u u u
MISCELLANEOUS KEY PROGRAMMING (−)
63
FS SALE u
u u
u u u
u u o o u
u o o u
u
u u
u u u
u u o u u
u u u
159
@/FOR
2316
FINAL
*Items marked with a circle (o) are usable. ((u) means unusable.)
0
XXX
@/FOR
A
A: CAT
SBTL
CA/AT
0
Compulsory
1
B: CAT action
XXX: Function No.
Function No.
Function
1
(−) 1
2
(−) 2
3
(−) 3
4
A:
(−) type
(−) 4
Subtotal (−)
0
Item (−)
1
MRS = 0
0
Dial
1
C: CAT type
C
Credit
0
Debit
1
Check
2
0
No
1
E
Partial
0
Full
1
F: CAT signature line print
F
Yes
0
No
1
G: CAT expiration printing
G
Yes
0
No
1
PROGRAM (PGM2/PGM1) MODE
2 – 17
D
Yes
E: Card number print format
ER-A410U/A420U
B
POST-AUTH
D: Card number is printed
A
A
Non-compulsory
u
u
H: Number of CAT authorization
receipt
Number
K:
L:
M:
N:
MEDIA KEY PROGRAMMING-2
0 to 9
I: Bill (slip) print
J:
[JOB#2326]
H
@/FOR
2326
No change
I
Non-compulsory
0
Compulsory
1
Footer print on receipt
J
No
0
Function No.
Function
Yes
1
61
CA1
62
CA2
76
CH1
78
CH2
Non-add code entry
K
Non compulsory
0
ABCD
Compulsory
1
80
CH3
Change due
L
82
CH4
Enable
0
84
CH5
Disable
1
86
CHK
87
CHK2
VP
M
Noncompulsory
0
Compulsory
1
Drawer opening
N
Yes
0
No
1
Entry of amount tendered
O
Non compulsory (Cash,Check)
Inhibit (Credit)
0
Compulsory
1
CURRENCY SYMBOL PROGRAMMING FOR EXCHANGE KEYS
@/FOR
2326
No change
@/FOR
Character key
CA/AT
XXX: Function No.
Function
71
Conversion 1
[JOB#2321]
72
Conversion 2
MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)
73
Conversion 3
74
Conversion 4
@/FOR
Range
4 characters
A character can be entered by using character keys or numeric keys.
The key sequence for entering one character by numeric keys is as
follows:
0
@/FOR
SBTL
Function No.
Function No.
XXX
CA/AT
[JOB#2334]
MRS=000000000000000
2321
SBTL
XXX: Function No.
XXX
O:
@/FOR
XXX
YYYYYYYY
SBTL
XXX 3 00 KEY
CA/AT
XXX: Character code (3 digits)
MRS = “space”
This symbol is printed when the foreign currency amount is positive.
The programmed characters are printed at left side of amount.
XXX: Function No.
YYYYYYYYY: Limitation amount
Func. No.
Function
Ex) Case of “ US$”:
Entry range
CONV1
MRS
68
CA/CHK
0 to 99999999
99999999
89
CID (Sentinel)
0 to 999999999
999999999
69
CHK CHANGE
0 to 99999999
99999999
1.234567
US$1.23
Programmed symbol
If some space characters are programmed at the left side of symbol
(like “ $”), they are not counted as the characters when the currency
symbol is printed. (In case of “ US$”)
Ex) Case of “ US$”: (The currency symbol means “DM”)
DEPARTMENT01 US$10000.00
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 18
[JOB#1500]
[JOB#2611]
CASHIER CODE DEFINITION
TIME SETTING
0
@/FOR
1500
0
@/FOR
XX
@/FOR
2611
YYYY
SBTL
XXYY
CA/AT
CA/AT
XX: Hour (00~23)
YY: Minute (00~59)
XX: Cashier No.= 1~20
The date entry does not comply with the SRV#912-B setting.
YY: Cashier code = 1~9999
MRS = 00:00
MRS = Same code as cashier No.
[JOB#2612]
[JOB#1514]
MACHINE NUMBER SETTING
CASHIER NAME PROGRAMMING
0
@/FOR
1514
YYYY
@/FOR
Character key
@/FOR
2612
No change
SBTL
CA/AT
CA/AT
XXXXXX
XXXXXX: Machine number (0~999999)
MRS = 000000
YYYY: Cashier code = 1~9999
Characters can be entered by using character keys or numeric keys.
The key sequence for entering one character by numeric keys is as follows:
XXX 3 00 KEY
[JOB#2613]
CONSECUTIVE NUMBER SETTING
0
XXX: Character code (3 digits)
@/FOR
2613
XXXX
CA/AT
Max. 8 characters
XXXX: Consecutive number (0000~9999)
MRS = ‘Space’
MRS = 0000
[JOB#2510]
[JOB#2614]
CASHIER DRAWER NO. ASSIGNMENT
LOGO TEXT PROGRAMMING
@/FOR
2510
0
YYYY
@/FOR
A
SBTL
No change
CA/AT
@/FOR
X
Position code
YYYY: Cashier code = 1~9999
A:
Drawer No.
@/FOR
2614
X: 1~6:
A
Character key
SBTL
CA/AT
1
(24 char.)
(24 char.)
Not open
0
2
Drawer 1
1
3
(24 char.)
2
4
(24 char.)
5
(24 char.)
6
(24 char.)
Drawer 2
MRS = 1
(1 Block max. 24 char.)
[JOB#2610]
Character can be entered by using character keys or numeric keys.
DATE SETTING
2610
@/FOR
XXXXXXXX
The key sequence for entering one character by numeric keys is as follows:
CA/AT
XXX 3 00 Key
XXX: Character code (3 digits)
XXXXXXXX: YYYYMMDD or DDMMYYYY or MMDDYYYY
(YYYY: 2000~2099)
(MM: 01~12)
(DD: 01~31)
(ER-A410)
Default =
The date entry format must comply with the applicable SRV-mode
(SRV#912-A) setting.
MRS = 01/01/2000
(DDMMYYYY)
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 19
(ER-A420)
Note: This programming is related to the JOB# 912-D setting.
The programable line has the below relations based on the
selection made in JOB# 912-D.
“6-line header”:
All 6 lines are programmable.
“3-line header”:
Upper 3 lines (1st-3rd line) are programmable.
“3-line footer”:
G: Subtotal void in REG mode
Enable
0
Disable
1
H: Refund VP
H
Lower 3 lines (4th-6th line) are programmable.
“Graphical LOGO only”: No lines are programmable.
Non compulsory
0
Compulsory
1
XX: 2
[JOB#2615]
MRS = 00000000
A: The first last item void
PROGRAMMING LIMITATION OF VALIDATION PRINTING AND
THE NO. OF LINE FEED AFTER PRINTING TRAY ST.
0
@/FOR
2615
CA/AT
A
Enable
0
Disable
1
B: PLU SHIFT LEVEL reset
VVXXAB
G
B
Auto
0
Manual
1
VV: INITIAL SLIP FEED LINE = 0 to 64
C: PLU LEVEL SHIFT
XX: SLIP PRINT MAX LINE NO. = 0 to 99
A: No. of times validation printing is enforced = 0 to 9
C
REG & MGR
0
MGR only
1
B: No. of feed lines after the despression of Tray ST key = 0 to 9
D: Printing of the number of items
MRS = 009910
[JOB#2616]
OPTIONAL FEATURES
0
XX
@/FOR
No
0
Yes
1
E: Time print
@/FOR
2616
ABCDEFGH
SBTL
XX: 1
MRS = 00000000
A: OP X/Z report
Enable
0
Disable
1
B: PO operation in REG mode
Enable
Disable
C: Refund type of sale function in REG mode
0
No
1
0
1
0
Disable
1
1
0
Disable
1
H
Non compulsory
0
Compulsory
1
MRS = 00000000
A, B: Not used (Fixed at “00”)
C: Zero skip in Cashier report
D: "RFND" key entry in REG mode
G
Enable
XX: 3
C
Enable
0
Journal select
H (−) VP
B
F
Full print
G: Item VP
A
E
Yes
F: Printing of journal
CA/AT
D
C
D
Yes
0
Enable
0
No
1
Disable
1
D: Zero skip in Transaction report
E: Direct void function in REG mode
D
E
Yes
0
Enable
0
No
1
Disable
1
E: Zero skip in Dept. report
F: Indirect void in REG mode
E
F
Yes
0
Enable
0
No
1
Disable
1
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 20
F: Zero skip in PLU report
F
Yes
0
No
1
G: Zero skip in Hourly report
XX: 8
MRS = 00000000
A, B, C: Not used (Fixed at “000”)
D: Entry of RA and RA2 key
G
Yes
0
Always
No
1
PBLU only
H: Zero skip in Daily net report
No
XX: 4
E: Check cashing VP
H
Yes
0
1
E
0
Non-compulsory
0
1
Compulsory
1
F: RA VP
MRS = 00000000
A, B, C, D, E, F, G: Not used (Fixed at "0000000")
H: PLU SHIFT LEVEL AUTO reset timing.
(Available when “X = 2, B = 0: PLU SHIFT LEVEL
reset = AUTO”)
D
0
1 receipt
1
0
Compulsory
1
G: PO VP
H
1 item
F
Non-compulsory
G
Non-compulsory
0
Compulsory
1
H: Not used (Fixed at “0”)
XX: 5
MRS = 00000000
XX: 9
MRS = 00000000
A, B, C, D, E: Not used (Fixed at “00000”)
A, B: Not used (Fixed at “00”)
F: PLU PRICE SHIFT
F
REG & MGR
0
MGR only
1
G: PLU PRICE LEVEL reset
C: Birthday print on printer
C
Yes
0
No
1
G
Auto
0
Manual
1
H: PLU PRICE LEVEL auto reset timing
(Available when “PLU PRICE LEVEL reset
=AUTO”)
D, E, F. G: Not used (Fixed at "0000")
H: Footer graphic LOGO printing at the end of receipt
H
1 item
0
1 receipt
1
H
No
0
Yes
1
XX: 10
MRS = 00000000
A, B, C, D, E, F, G, H: Not used (Fixed at “0000000”)
XX: 6
MRS = 00000000
XX: 11
A, B, C, D, E, F, G: Not used (Fixed at "0000000")
XX: 7
A, B, C, D, E, F, G, H: Not used (Fixed at “0000000”)
MRS = 00000000
XX: 12
A, B: Not used (Fixed at “00”)
C: No sale in REG mode
MRS = 00000000
MRS = 00000000
A, B, C, D, E, F, G, H: Not used (Fixed at “0000000”)
C
XX: 13
MRS = 00000000
Enable
0
Disable
1
A, B, C: Not used (Fixed at "000")
D
D: Printing of price shift text on the receipt/journal
D: Finalization in REG mode when ST is zero
Enable
0
Yes
Disable
1
No
E: Printing of item in PBLU transaction on SLIP
E, F, G, H: Not used (Fixed at "0000")
E
Yes
0
No
1
F, G, H: Not used (Fixed at "0000")
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 21
D
0
1
[JOB#2617]
[JOB#2620]
PROGRAMMING OF THE TIME INTERVAL FOR THE TILL TIMER
STACK REPORT
0
@/FOR
2617
XXX
2620
@/FOR
CA/AT
All delete
No range
XXX: 0 ~ 255 sec
MRS = 000
XX
@/FOR
SSSSSS
@/FOR
SBTL
EEEEEE
[JOB#2618]
Next job#
SCALE TABLE PROGRAMMING
CA/AT
0
2618
X
@/FOR
@/FOR
XX: JOB#
YYYY
SBTL
SSSSSS: Start code
CA/AT
EEEEEE: End code
X: Table No. = 1 - 9
JOB#
YYYY: Weight = 0 - 99.99 (Enter without decimal point.)
REPORT NAME
TYPE
00
General
MRS = 0.00
10
DEPT.
[JOB#2619]
13
DEPT. All group
HOURLY REPORT (Starting time)
20
PLU
RANGE
24
PLU stock
RANGE
27
PLU zero sales
29
PLU category
30
Transaction
0
@/FOR
2619
A:
ABB
CA/AT
Memory format
A
30 minutes (24 hour)
0
60 minutes (24 hour)
1
BB: Starting time (hour):
00~23
MRS = 000
31
CID
32
Commission sales
50
All cashier
60
Hourly
70
Daily net
80
PBLU
RANGE
ALL
RANGE (only X report)
ex)
2619
@/FOR
007
CA/AT
RANGE
X1 Hourly report (#160) (30 min, start time = 7)
[**]
#160
7:00
(DATA)
7:30
(DATA)
SUBTOTAL
(DATA)
|
23:30
(DATA)
SUBTOTAL
(DATA)
0:00
(DATA)
0:30
(DATA)
SUBTOTAL
(DATA)
|
6:30
(DATA)
SUBTOTAL
(DATA)
The maximum of 70 steps are programmable. “1 step” means the memory size used for one no range type JOB#.
The RANGE type JOB# means “8 steps”.
For example)
The memory size for programming JOB#00, 20 and 50 is 10 steps.
(ie. 1 step for JOB#00, 8 step for JOB#20, and 1 step for JOB#50.)
[JOB#2630, 2631, 2632]
SECRET CODE PROGRAMMING
0
2630
2631
2632
24 hours started
from 7:00
@/FOR
XXXX
CA/AT
#2630: PGM1 mode
#2631: X1/Z1 mode
#2632: X2/Z2 mode
*If “0” is entered, “compulsory secret code entry” is not enabled.
MRS = 0
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 22
[JOB#2641]
No.55~66 are all reserved.
No.
MESSAGE TEXT PROGRAMMING
67
@/FOR
2641
No change
XX
@/FOR
Characters
MRS
REG buffer full
BUFFER FULL
No.68~75 are all reserved.
SBTL
CA/AT
No.
Message No.
Description
76
Close drawer error
No.
Messages are 12 CHARACTERS
Description
MRS
CLOSE DRAWER
No.77~80 are all reserved.
XX: Message No. = 1 to 99
No.
Description
MRS
1
Registration error
ENTRY ERROR
2
Misoperation error
MISOPERATION
3
Desired code is not programmed yet.
NO RECORD
4
(Reserved)
5
Secret code error
SECRET CODE
6
Code is not free
NOT FREE
7
Memory is full
MEMORY FULL
8
Insert slip paper
INSERT SLIP
9
The cashier has entered a code for NO AUTHORITY
which he or she is not authorized.
Description
81
Enter secret code
82
(Reserved)
83
(Reserved)
84
DATA BACKUP send success
SEND OK
85
DATA BACKUP receive success
RECEIVE OK
86
DATA BACKUP communication error COM. ERROR
87
DATA BACKUP data format error
DATA ERROR
88
DATA BACKUP timeout error
TIME OUT
89
(Reserved)
90
(Reserved)
91
(Reserved)
(Reserved)
10
Stock is empty
OUT OF STOCK
92
11
Compulsory of pushing the SBTL key
SBTL COMPUL.
93
(Reserved)
94
Age verification error
12
Compulsory of tendering
TEND COMPUL.
13
PBLU entry compulsory
PB COMPUL.
MRS
ENTR SECRET#
AGE ERROR
[JOB#2642]
No.14~21 are all reserved.
No.
Description
VP TEXT PROGRAMMING
MRS
No change
22
(Reserved)
23
Cashier resetting over error
24
(Reserved)
25
(Reserved)
26
(Reserved)
27
Power off
28
(Reserved)
29
(Reserved)
30
(Reserved)
31
Compulsory of non-add code entry
# COMPULSORY
32
The cashier key is not assigned.
NOT ASSIGNED
33
(Reserved)
34
Overflow limitation
OVER LIMIT.
35
The open price entry is inhibited.
INH. OPEN PR
36
The unit price entry is inhibited
INH. UNIT PR
37
The direct non-tendering finalization NOT NON-TEND
after previous tender entry is inhibited.
38
Read error of scale
2642
ENTRY ERR CA
@/FOR
X
@/FOR
Position code
Characters
SBTL
CA/AT
X: Position code = 1 to 3
1 BLOCK MAX. 24 CHARACTERS
POWER OFF
MRS = “
“
“
“
“FOR DEPOSIT ONLY”
[JOB#2643]
SLIP TEXT PROGRAMMING
No change
2643
@/FOR
X
@/FOR
Character
key
Position code
SBTL
SCALE ERROR
X: Position code = 1 to 3
No.39~50 are all reserved.
No.
Description
1 BLOCK MAX. 24 CHARACTERS
MRS
MRS = “SPACE”
51
Weight on scale
52
(Reserved)
WEIGHT
“SPACE”
53
(Reserved)
“SPACE”
54
Entry tare weight
ENTR TARE WT
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 23
CA/AT
[JOB#2689]
* EFT FUNCTION always uses RS port 2.
POWER SAVING PROGRAMMING
@/FOR
2689
(Note: When the ER-03EF is connected, RS port 2 cannot be used
for other purposes.)
CA/AT
XYYY
*DATA BACK UP FUNCTION always uses RS port 1.
X: POWER SAVING function when a time is displayed
(Note: If RS port 1 is not used by DATA BACKUP FUNCTION, it is
available for other RS functions by setup.)
X
Yes
0
No
1
[JOB#2710]
TAX TABLE PROGRAMMING
YYY: POWER SAVING TIME to POWER OFF = 001-254 (minutes)
or 999 (Inhibit)
2710
@/FOR
MRS = 0030
AB
@/FOR
Declaration of TAX
Table Delete programming
[JOB#2690]
THE ASSIGNMENT OF RS232 FUNCTIONS BY EACH DEVICE
XXXX
Cycle
@/FOR
2690
@/FOR
XXX
X
@/FOR
ABCD
XXXXX
SBTL
SBTL
Initial TAX
@/FOR
Lower TAX limit
CA/AT
@/FOR
TAX rate
@/FOR
Table Delete programming
0
XX.XXXX
XXXXX
@/FOR
SBTL
CA/AT
Break point
72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX TABLE.
X: 1
MRS = 0000
A: Channel No. for on-line or print data sending
*DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTS
WILL RESULT IN A TAX TABLE DELETE OPERATION.
A
Not connect
0
RS port 1
1
RS port 2
2
(When the interval between break point is 1 dollar or more and less than
100 dollar, 36 breakpoints is programmed for each table.)
A:
INTERVAL BETWEEN BREAKPOINTS IS BELOW 1 DOL- = 0
LAR
B: Not used (Fixed at “0”)
C: Channel No. for SCALE
No
Channel No.
D: Channel No. for coin dispenser
No
Channel No.
INTERVAL BETWEEN BREAKPOINTS IS 1 DOLLAR OR = 1
MORE AND LESS THAN 100 DOLLAR
B:
C
0
1 or 2
D
TABLE 1 PROGRAMMING
=1
TABLE 2 PROGRAMMING
=2
TABLE 3 PROGRAMMING
=3
TABLE 4 PROGRAMMING
=4
TAX RATE
0
1 or 2
X: 2 Not used (Fixed at “0000“)
MRS = 0000
X: 3
MRS = 0000
: 0-9999
INITIAL TAX
: 0-999
LOWER TAX LIMIT : 0-99999
BREAK POINT
MRS = NO TAX
A: Not used (Fixed at “0”)
B: Channel No. for slip printer
B
Not connect
0
RS port 1
1
RS port 2
2
C: Not used (Fixed at “0”)
D: Channel No. for CAT
No
Channel No.
D
0
1 or 2
ER-A410U/A420U
: 0.0001-99.9999
CYCLE
PROGRAM (PGM2/PGM1) MODE
2 – 24
: 0-99999
[JOB#2711]
[JOB#2900]
TAX RATE PROGRAMMING
<CAUTION>
(This JOB must be performed at the X2/Z2 mode position.)
2711
@/FOR
@/FOR
A
Declaration
of TAX
XX.XXXX
AUTO - AUTO5 KEY SETTING
TAX rate
Max.50
2900
CA/AT When lower
@/FOR
tax Limit is 0
AUTO2
ST
@/FOR
Tax Table delete
operation
A: TAX 1 PROGRAMMING = 1
CA/AT
Delete
AUT O3
AUTO3
AUTO4
AUT O4
AUT O5
AUTO5
AUTO10
AUTO10
• This machine has up to 5 [AUTO] keys which can be programmed by
the following key-sequence.
TAX 3 PROGRAMMING = 3
TAX 4 PROGRAMMING = 4
• When the [AUTO] key is depressed, the machine works the same as
the programmed key-sequence programmed.
X
+
0
-
1
<Example>
(X2/Z2)
2900
XXX.XXXX:
AUTO
AUT O2
(Auto key function)
TAX 2 PROGRAMMING = 2
X: % TAX RATE & SIGN
(Free key)
AUTO
@/FOR
RATE = 0.0000 to 99.9999 %
AUTO
PLU1
100
DEPT2
CA/AT
AUTO
(1-5)
ZZZZZ: LOWER TAX LIMIT = 0.00 to 999.99
(REG)
(This invalid in VAT system.)
Key entry
MRS = DELETE
AUTO
R/J
PL000001
Display
1.10
Comment
PL0000001 1.10
same as
PLU1 entry
1
same as
1 entry
10
same as
0 entry
100
same as
0 entry
[JOB#2715]
QUANTITY FOR DOUGHNUT EXEMPT (For Canadian TAX)
0
DEPT02
2715
@/FOR
XX
1.00
DEPT02
1.00
same as DEPT2 entry
CA/AT
(X2/Z2)
XX: Quantity for doughnut TAX exempt = 0-99
2900
MRS = 0
@/FOR
AUTO2
CA/AT
100
AUTO2
CA/AT
(REG)
[JOB#2810]
PBLU code (The range programming of available PBLU codes)
Key entry
DEPT 1
One code
R/J
DEPT01
Display
1.00
DEPT01
Comment
1.00
AUTO 2
2810
@/FOR
XXXX
@/FOR
YYYY
CA/AT
XXXX: Start code = 1-9999
YYYY: End code = 1-9999
MRS = 0001 (Start code)/1000 (End code)
ER-A410U/A420U
same as
1 entry
same as
0 entry
100
same as
0 entry
***TOTAL
1.00 CHANGE
CASH
1.00
CHANGE
0.00
PROGRAM (PGM2/PGM1) MODE
2 – 25
1
10
0.00
same as CA/AT entry
[JOB#2990]
[JOB#6113]
THERMAL PRINTER PROGRAMMING
RS-232C PROGRAMMING
0
0
@/FOR
2990
CA/AT
ZZ
@/FOR
6113
ZZ: Selection of light and shade
ZZ
XXX: Start code (000-127)
Lighter than standard
00
YYY: End code (000-127)
Standard (90% for printer standard)
50
Darker than standard
99
XXXYYY
CA/AT
MRS = 002013
[JOB#6115]
MRS = 50
RS-232C TIME OUT
[JOB#6110]
@/FOR
6115
RS-232C TERMINAL No.
XXX
CA/AT
0
XXX: Time out time (1-255 sec)
@/FOR
6110
XXXXXX
CA/AT
MRS = 007
XXXXXX: Terminal number (0 to 999999)
[JOB#6220]
MRS = 000001
PRINT DATA SENDING
[JOB#6111]
0
RS-232C TRANSMISSION
@/FOR
6220
ABC
CA/AT
0
@/FOR
6111
AB
CA/AT
A: Sending of CI signal
A: Sending of DR signal
A
No
0
Yes
1
B: Transmission line form
B
Full duplex system
0
Half duplex system
1
0
No
1
B: Sending of CS signal
[JOB#6112]
0
No
1
0
Enable
1
MRS = 000
0
@/FOR
AB
CA/AT
A: Print data
A
Data download and upload
0
Print data send
1
B: RS-232C Baud rate
B
4800bps
4
9600bps
5
19200bps
6
38400bps
7
(*) Data value “3/2/1/0” is reserved.
Note: The value of the baud rate is used for the Online communication
and Print data functions.
It is not used for the Data back up function (SRV#996, SRV#998).
MRS = 06
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 26
C
Disable
RS-232C FUNCTION SELECTING
6112
B
Yes
C: Sending of all print data
MRS = 00
A
Yes
[JOB#7110]
[JOB#7112]
CAT DIAL OUT PHONE NUMBER PROGRAMMING
CAT FUNCTION SELECTING
0
No change
@/FOR
7110
Characters
@/FOR
7112
CA/AT
ABCDEF
CA/AT
A: PIN PAD on CAT for DEBIT CARD
(CHARACTERS): CHARACTER (Max. 25 Characters)
Characters can be entered by using the character layout on keyboard or
by using the numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
YES
0
NO
1
B: KEY TYPE for PIN PAD
B
STATIC
YYY3 [00] KEY YYY: CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
A
0
DUKPT
1
INDEX
2
MRS = 0_____________________ (_: space code)
C: DIAL MODE for DIAL OUT
Note: Any character can be set as text.
Valid characters for dialing are “0” to “9”, “W” and “,”.
The text setting of invalid characters (like “space”) are ignored
when dialing.
Example: “0123, 45, 6789__123______” 3 Dial = “0123, 45, 6789”
C
TONE
0
PULSE
1
MRS = 000
“0123, 45xx789 ___________” 3 Dial = “0123, 45”
[JOB#7113]
[JOB#7111]
CAT TIME OUT1 (for reading of Card [Credit, Debit card])
CAT PASSWORD for DIAL OUT
0
0
7113
7111
@/FOR
XXXXXXXX
@/FOR
XXX
CA/AT
CA/AT
XXX: Time out time (1-255 sec)
XXXXXXXX: Password (TEL ID) 8 digits (00000000-99999999)
MRS = 030
Note:
• This data can be programmed with zero suppress.
This may also be used without zero suppress for dialing.
[JOB#7114]
CAT TIME OUT2 (for response of Authorization)
0
• “PHONE NUMBER for DIAL OUT” is “TEXT” programming
[JOB#7110].
7114
MRS = 00000000
@/FOR
XXX
CA/AT
XXX: Time out time (1-255 sec)
MRS = 099
[JOB#7115]
CAT TIME OUT3 (for reading of Dial in/out)
0
7115
@/FOR
XXXX
CA/AT
XXX: Time out time (1-3000 sec)
MRS = 0099
Note: JOB#7117, JOB#7118 and JOB#7119 are used by
“CAT COMMUNICATIONS” (Executing JOB).
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 27
3. PROGRAMMING BY DIRECT KEY
F: Taxable 3
1) DEPT UNIT PRICE
MODE: PGM1, PGM2
No
0
Yes
1
G: Taxable 2
0
CA/AT
DPTn
XXXXXX
F
G
No
0
Yes
1
0
YY
DEPT#
XXXXXX
H: Taxable 1
SBTL
YY: Department Code (01-99)
If a price is set for a department which the amount entry type is
“INHIBIT” or “OPEN”, the amount entry type is changed automatically
as indicated below.
0
Yes
1
0
Compulsory
1
J: Tare table No. = 9 to 1, 0
Inhibit
“OPEN & PRESET”
MRS = 0
2) (-) PRESET AMOUNT
MODE: PGM1, PGM2
CA/AT
(-) n
XXXXXX
1
2
0
SICS
1
SIF
2
0
ABCDEFGHI
JKLMNOP
@/FOR
DPTn
CA/AT
0
YY
DEPT#
ABCDEFGHIJKK
1
Bottle return
2
N
Inhibit
0
Open only
1
Preset only
2
Open & Preset
3
O: HALO Mantissa = 0 to 9
P: HALO Exponent = 0 to 7
H and I indicate A x 10B
Except the value A and B, any amount over 9999999 can not
be entered.
MRS = 000100118001
(TAXABLE 1, VP Non-compulsory, NORMAL, Open only,
HALO = 17, Commission =0, Group =01)
A: Group No. = 0 to 9
B: Commission group = 0 to 9
C: Sign
C
+
0
–
1
D
No
0
Yes
1
E: Taxable 4
0
@/FOR
YY: Department code (01-99)
D: Food stampable
M
HASH
N: AMOUNT ENTRY TYPE
3) DEPT FUNCTION PROGRAMMING
MODE: PGM2
L
NORMAL
NORMAL
MRS = 0
0
Compulsory
M: Bottle return
XXXXXX: Unit price (Max. 6 digits)
K
Enable
L: REGISTRATION TYPE
0
I
Non-compulsory
K: Scale entry
”INHIBIT” 3 “PRESET”
”OPEN” 3
No
I: ITEM VP
XXXXXX: Unit price (Max. 6 digits)
H
E
No
0
Yes
1
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 28
4) (-) & % KEY FUNCTION PROGRAMMING
MODE: PGM2
5) RATE PROGRAMMING FOR % AND CONVERSION
KEY MODE: PGM1, PGM2
0
%n
0
(-) n
ABCDE
FGHI
@/FOR
CONV1
CA/AT
%n
CA/AT
(RATE)
CONV2
CONV3
A: Amount entry type
A
Inhibited
0
Open
1
Preset
2
Open and preset
(RATE): XXX.XX: Rate for % (0.00-100.00)
XXXX.XXXX: Rate for CONVERSION (0.0000-9999.9999)
The DECIMAL POINT must be entered for setting the decimal digits.
3
MRS = 0.00 (%n)
B: Food stamp
B
Non-food stampable
0
Food stampable
1
C: Taxable4
0
Taxable
1
0
Taxable
1
0
AB
0
Taxable
1
0
Taxable
1
@/FOR
POn
CA/AT
A: HALO Mantissa = 0 to 9
B: HALO Exponent = 0 to 9 (for RAn, POn)
0 to 7 (for Manual TAX)
F
Non taxable
RAn
TAX
For manual TAX
E
Non taxable
F: Taxable1
6) PROGRAMMING FOR RA/PO KEYS
MODE: PGM2
D
Non taxable
E: Taxable2
Note: This programming is invalid for [CONV4] key.
The [CONV1], [CONV2] and [CONV3] keys are used only for
PRESET RATE REGISTRATION but the [CONV4] is used only
for OPEN RATE REGISTRATION.
C
Non taxable
D: Taxable3
0.0000 (CONVn) (n=1-3)
H and I indicate A x 10B
Except the value A and B, any amount over 999999999 can not be
entered.
MRS = 19 for RAn, POn
G: SIGN
G
+
0
-
1
H: ITEM / SBTL (-) / %
17 for TAX
7) PROGRAMMING FOR MEDIA KEYS & FUNCTION KEYS
MODE: PGM2
H
ITEM (-) / %
0
SBTL (-) / %
1
( [SBTL] key is used for programming of CASH.)
CHKn
0
CHn
ABCDEFGH
IJKLMNOPQ
I: HALO Mantissa (for (-) key) = 0 to 9 (0 FIXED for [%n] )
J: HALO Exponent (for (-) key) = 0 to 7 (0 FIXED for [%n] )
CA/AT
CA2
SBTL
H & I indicate C x 10D
Except the value C and D, any amount over 9999999 can not
be entered.
(for CASH)
A: CAT
HALO = 00: OPEN PRICE REGISTRATION INHIBIT (for [(-) n].
MRS = 0000001017 for [(-) n]
(MINUS SIGN, SBTL (-), HALO =9999999)
0
Compulsory
1
B
POST-AUTH
0
DIAL
1
C: CAT Type
C
Credit
0
Debit
1
Check
2
PROGRAM (PGM2/PGM1) MODE
2 – 29
A
Not
B: CAT action
3000001000 for [%n] (MINUS SIGN, SBTL%)
ER-A410U/A420U
@/FOR
D: Card number is printed
8) PROGRAMMING OF ASSOCIATED DEPARTMENT
FOR PLU
MODE: PGM1, PGM2
D
Yes
0
No
1
E: Card number print format
Ln
E
Partial
0
Full
1
F: CAT signature line print
XXXXXX
PLUn
VOID
PLUn
DPTn
YY
PLU/SUB
F
Yes
0
No
1
G: CAT expiration printing
(Code increment)
(Code entry)
Ln: MENU LEVEL (1-3)
G
Yes
0
No
1
XXXXX: PLU CODE (1-999999)
YY: DEPT CODE (1-99)
When a DEPT is assigned to a deleted or new PLU, the PLU is set the
MRS value with exception of the presets of the associated DEPT.
H: Number of CAT authorization receipts = 0 to 9
I: SLIP PRINT
MRS = DEPT1 (PLU1-PLU20)
I
Non-compulsory
0
Compulsory
1
J: Footer print on Recipt
CA/AT
DEPT#
9) PLU UNIT PRICE
MODE: PGM1, PGM2
J
No
0
Yes
1
K: Non-add code entry
K
Non-compulsory
0
Compulsory
1
Ln
PLUn
PLUn
XXXXXX
PLU/SUB
0
0
YYYYYY
PRICE1
ST
YYYYYY
PRICE2
SBTL
CA/AT
CL
(Code increment)
(Code entry)
L: Change due
L
Enable
0
Disable
1
M: VP
XXXXXX: PLU CODE (1-999999)
YYYYYY: UNIT PRICE (6 digits)
When a DEPT is assigned to a deleted or new PLU, the PLU is set the
MRS value with exception of the presets of the associated DEPT.
M
Non-compulsory
0
Compulsory
1
N: Drawer opening
N
Yes
0
No
1
O: Entry of amount tendered
MRS = Price: 0, Price2: 0 (PLU1-PLU20)
O
non-compulsory (Cash, Check) inhibit (Credit)
0
compulsory
1
P: HALO Mantissa = 0 to 9
Q: HALO Exponet = 0 to 8
I and J indicate I x 10J
Except the value I and J, any amount over 99999999 can not
be entered.
MRS = 00000000000000018 (CA, CHKn, CHn)
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 30
10) PLU FUNCTION PROGEAMMING
MODE: PGM2
Ln
TAX
AB
@/FOR
Declaration of tax
PLUn
PLU/SUB
PLU CODE
XX. XXXX
TAX rate
0
PLUn
XXXXXX
11) TAX TABLE PROGRAMMING
MODE: PGM2
ABCDE
FGHIJ
@/FOR
Table delete programming
@/FOR
SBTL
CA/AT
XXXX
Cycle
(Code increment)
*
@/FOR
(Code entry)
XXX
Initial tax
@/FOR
Table delete programming
SBTL
XXXXXX: PLU CODE (1-999999)
A: Commission group No. = 0 to 9
B: Sign
B
+
0
-
1
C: Food stampable
XXXXX
@/FOR
Lower TAX limit
0
Yes
1
@/FOR
CA/AT
72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAXTABLE.
(If the interval between break points is 1 dollar or more and less than 100
dollar, a maximum of 36 break points is programmed for each table.)
C
No
XXXX
Break point
*DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTS
WILL RESULT IN A TAX TABLE DELETE OPERATION.
A: INTERVAL BETWEEN BREAKPOINTS
D: Taxable 4
A
D
1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR
1
No
0
BELOW 1 DOLLAR
0
Yes
1
B: TAX TABLE No.
E: Taxable 3
A
E
TABLE4
4
No
0
TABLE3
3
Yes
1
TABLE2
2
TABLE1
1
F: Taxable 2
F
No
0
TAX RATE:
Yes
1
CYCLE:
0-9999
INITIAL TAX:
0-999
G: Taxable 1
G
No
0
Yes
1
LOWER TAX LIMIT: 0-99999
BREAK POINT:
0
Enable
1
Compulsory
2
J: Amount entry type
12) DATE/TIME PROGRAMMING
MODE: PGM2
I
Inhibit
XXXXXXX
DATE
(8 digit)
0
Open only
1
Preset only
2
Open & Preset
3
#/TM
XXXX
TIME
(4 digit)
J
Inhibit
0-99999
MRS = NO TAX
H: Tare Table No. = 9 to 1, 0
I: Scale entry
0.0001-99.9999
DATE) XXXXXXXX: YYYYMMDD or DDMMYYYY or MMDDYYYY
(YYYY: 2000-2099)
(MM: 01-12)
(DD: 01-31)
The date entry format complies with SRV#912-A.
When a DEPT is assigned to a deleted or new PLU, the PLU is set the
MRS value with exception of the presets of the associated DEPT.
TIME) HH: Hour (00 to 23)
MM: Minute (00 to 59)
MRS = 00001200 (PLU1 to PLU20)
The time entry does not complies with SRV#912-B.
(Sign +, Taxable 1, Preset only, Commmission: 0, Base quantity: 0)
MRS = 01/01/2000 (DDMMYYYY)
00:00
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 31
4. CHARACTER ASSIGNMENT METHOD
~ Using the alphabetic assignment method ~
Push alphabetic
ST
Repeat
Programming key layout
ER-A410
Ø
(NUM) (SPACE) CASH
#
@
RECEIPT JOURNAL
( )
( )
7
( )
( )
PO
( )
(%)
( )
( )
”
CL
FOR
8
4
9
’
6
:
3
+
5
2
1
0
#
”
A
M
=
<
>
Pt
R
?
Z
W
SBTL
S
£
O
J
E
Y
V
Ç
N
I
D
X
)
!
.
H
-
(
Q
L
,
;
)
&
U
/
G
B
(
%
P
K
@
C
00
$
F
æ BACK
Æ SPACE
cl
(SHIFT-2) (SHIFT)
(DC)
Ø
CA/AT/NS
T
ER-A420
}
?34
<41
>48
3
1
!
@
#
$
%
^
L2
&
1
Ï2
3
4
5
6
7
85
912
019
+26
Q
W
E
R
T
Y
U
I
4
O11
P18
_25
7
8
9
A
S
D
F
G
H
J
K3
L10
/ 17
=24
4
5
6
Z
X
C
V
B
N
M2
;
:
1
2
3
(SHIFT) (DC) (SPACE) (SPACE) (SPACE) (SPACE) (SPACE) (SPACE)
,
.
0
00
2
”
”
6
( 13
)
N
,
-33
[
@
]
BACK
(SPACE
)
CL
FOR
SBTL CA/AT
4
4 Using ten key of ECR
Notes:
• The programming keyboard sheet is transparent, allowing placement
over the standard keyboard sheet.
• The shaded area containts the character keys which are used for programming characters.
[(DC)]
[(SHIFT)]
[(SHIFT2)]
[(BACK SPACE)]
[(SPACE)]
[(Num)]
?
d
{
e
RECEIPT JOURNAL
: Used to enter the double-size character.
: Used to change a lower-case letter/upper-case letter.
: Used to select a symbol.
: Used to back up the cursor for deleting.
: Used to enter a space.
: Used to enter a numeric character.
c æ
XXX
3 digits
00
ST
Repeat
Note: [00] key is used to enter each 3 digit alpha code.
Examples
“
l
A
3
“
A
= A is set
[(Shift-2)] 3
“
A
= “ is set
3
“
A
= A (double character code) is set
[(Shift)] 3
“
A
= a (lowercase letter) is set
[(DC)]
Æ
*Once the [(Shift)] key is pressed, it stays down until it is pressed
again.
ER-A410U/A420U
PROGRAM (PGM2/PGM1) MODE
2 – 32
<Character Code Table for text programming> Printing
CODE
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
CODE
001
á
049
1
098
b
147
U
196
002
â
050
2
099
c
148
à
197
003
ê
051
3
100
d
149
Æ
198
004
î
052
4
101
e
150
φ
199
005
ì
053
5
102
f
151
Å
200
í
054
6
103
g
152
¤
201
007
ô
055
7
104
h
153
é
202
008
ó
056
8
105
i
154
è
203
009
û
057
9
106
j
155
Pt
204
010
ú
058
:
107
k
156
¡
205
059
;
108
l
157
Ñ
206
060
<
109
m
158
:
207
061
=
110
n
159
£
208
062
>
111
o
160
¥
209
063
?
112
p
161
210
Λ
064
@
113
q
162
211
017
Ψ
065
A
114
r
163
212
018
Γ
066
B
115
s
164
067
C
116
t
165
006
011
œ
012
013
ú
014
015
016
ó
019
..
020
Ω
021
∆
022
Θ
023
Ξ
024
Π
025
Σ
026
Υ
027
Φ
028
029
Ú
030
031
Ó
032
(Space)
033
!
034
"
035
#
036
$
037
%
038
&
039
CHARACTER
P
š
213
.
068
D
117
u
166
T
069
E
118
v
167
T
070
F
119
w
168
T
071
G
120
x
169
T
072
H
121
y
170
1
073
I
122
z
171
1
074
J
123
{
172
1
075
K
124
|
173
2
076
L
125
}
174
2
077
M
126
ß
175
3
078
N
127
079
O
128
!!
177
080
P
129
1
178
081
Q
130
2
179
082
R
131
3
180
4
214
1
215
2
216
3
217
4
218
2
219
3
220
4
221
3
222
4
223
4
224
176
Á
*
225
§
226
Ø
227
^
228
2
A
229
]
181
a
230
[
182
E
231
083
S
132
084
T
133
1
085
U
134
F
T
183
e
232
ä
086
V
135
1
184
I
233
ö
087
W
136
3
185
i
234
ü
'
088
X
137
p
186
U
235
æ
040
(
089
Y
138
p
187
u
236
å
041
)
090
Z
139
d
188
237
É
042
*
091
Ä
140
e
189
238
ñ
043
+
092
Ö
141
F
190
044
,
093
Ü
142
T
191
045
–
094
^
143
4
192
046
.
095
_
144
ç
193
047
/
096
145
O
194
048
0
097
146
¿
195
253
DC
a
/2
Note: The above character chart is for your reference.
Please check the actual print out.
Š
(DC): Double Code
: ECR Control Character (Not used for text)
ER-A410/ER-A420
PROGRAM (PGM2/PGM1) MODE
2 – 33
<Character Code Table for text programming> Display
CODE
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
001
á
049
1
098
b
147
U
196
(Space)
002
â
050
2
099
c
148
à
197
(Space)
003
ê
051
3
100
d
149
Æ
198
(Space)
004
î
052
4
101
e
150
φ
199
(Space)
005
ì
053
5
102
f
151
Å
200
(Space)
(Space)
054
6
103
g
152
¤
201
(Space)
Ô
055
7
104
h
153
é
202
ó
056
8
105
i
154
è
203
(Space)
009
û
057
9
106
j
155
Pt
204
(Space)
010
ú
058
:
107
k
156
i
205
(Space)
059
;
108
l
157
N
206
060
<
109
m
158
ò
207
061
=
110
n
159
(Space)
208
P
062
>
111
o
160
¥
209
(Space)
063
?
112
p
161
.
210
Λ
064
@
113
q
162
[
211
Ψ
065
A
114
r
163
]
212
Γ
066
B
115
s
164
,
213
067
C
116
t
165
(Space)
214
068
D
117
u
166
(Space)
215
069
E
118
v
167
(Space)
216
070
F
119
w
168
(Space)
217
071
G
120
x
169
(Space)
218
072
H
121
y
170
(Space)
219
073
I
122
z
171
(Space)
220
(Space)
074
J
123
{
172
(Space)
221
(Space)
075
K
124
|
173
(Space)
222
(Space)
076
L
125
}
174
(Space)
223
(Space)
077
M
126
ß
175
(Space)
224
*
078
N
127
¢
176
(Space)
225
(Space)
079
O
128
!
177
Á
226
Ø
080
P
129
1
178
(Space)
227
^
081
Q
130
2
179
(Space)
228
(Space)
082
R
131
3
180
(Space)
229
]
083
S
132
4
181
(Space)
230
[
084
T
133
(Space)
182
(Space)
231
(Space)
085
U
134
(Space)
183
(Space)
232
ä
086
V
135
1
184
(Space)
233
ö
087
W
136
3
185
(Space)
234
ü
æ
006
007
008
011
(Space)
012
013
ú
014
015
016
017
018
ó
019
(Space)
020
Ω
021
∆
022
Θ
023
Ξ
024
Π
025
Σ
026
Υ
027
Φ
028
029
Ú
030
š
(Space)
031
Ó
032
(Space)
033
!
034
"
035
#
036
$
037
%
038
&
039
'
088
X
137
(Space)
186
(Space)
235
040
(
089
Y
138
(Space)
187
(Space)
236
å
041
)
090
Z
139
d
188
(Space)
237
É
042
*
091
Ä
140
e
189
(Space)
238
ñ
043
+
092
Ö
141
F
190
044
,
093
Ü
142
T
191
045
–
094
^
143
(Space)
192
046
.
095
_
144
ç
193
047
/
096
145
O
194
048
0
097
146
¿
195
253
DC
a
Note: The above character chart is for your reference.
Please check the actual print out.
Š
(Space)
(DC): Double Code
: ECR Control Character (Not used for text)
ER-A410/ER-A420
PROGRAM (PGM2/PGM1) MODE
2 – 34
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE
In general, the following sales reports are available:
[Purpose]
1) OP X/Z reports (individual clerk reports)
The below reports are each used to check sales data. The intended
method of taking these reports are as follows:
2) X1/Z1 reports (Daily sales total X and Z reports)
OP X/Z reports: These reports are taken by operators in order to report
their own sales data.
3) X2/Z2 reports (Periodic total X and Z reports)
4) Flash-read reports (Display sales amount)
X1/Z1 reports: These reports are taken by the supervisor or manager
in order to check and report daily sales totals at that
point.
In addition to the above reports that are to be used, reports for checking
the program are also available.
X2/Z2 reports: These reports are taken by the supervisor or manager in
order to check and report periodic (weekly or monthly)
totals.
Flash-read:
These reports are taken by the owner or manager in
order to check and display sales totals at that point.
Reading
JOB#
@/FOR
Range is required
CA/AT
Resetting
[Operation]
In the table below those reports marked with a circle “o” can be executed.
PRINTING REPORT
MODE *1
REPORT NAME
JOB#
OPX/Z
X
GENERAL
x00
X1/Z1
Z
X2/Z2
DATA FOR READING
X1
Z1
X2
Z2
o
o
o
o
*2
DEPT (ALL GROUP)
x10
o
o
DEPT (INDIVIDUAL GROUP)
x12
o
o
GROUP TOTAL
x13
o
PLU
x20
o
o
o
o
PLU CODE
*4
o
o
o
DEPT CODE
*3
PLU CODE
*4
*2
GROUP No.
o
PLU (DEPT)
x21
o
PLU STOCK
x24
o
PLU ZERO SALES
x27
o
o
PLU PRICE CATEGORY
x29
o
o
*3
*2
*2
PRICE
*4
TRANSACTION
x30
o
o
*2
CID
x31
o
o
*2
COMMISSION
x32
o
CASHIER (ALL)
x50
o
o
o
o
o
o
o
o
o
o
o
*2
*2, *7
o
CASHIER (INDIVIDUAL)
x51
CASHIER (INDIVIDUAL)
x51
HOURLY (ALL)
x60
o
HOURLY (RANGE)
x60
o
*2, *5, *7
x70
PBLU
x80
PBLU (CASHIER)
x81
o
o
STACK REPORT
x90
o
o
o
*4
PBLU CODE
*4
*2
CASHIER CODE
o
OP X/Z, X1/Z1, X2/Z2 MODE
3–1
TIME
o
o
JOB# : ‘x’ is 1 for X1/Z1 mode, 2 for X2/Z2 mode, and 0 or nothing for OPX/Z mode.
ER-A410U/A420U
*6, *7
*2
o
DAILY NET
CASHIER CODE
o
*2
*8
FLASH READING REPORT
MODE
REPORT NAME
KEY ENTRY
OPX/Z
X
DEPARTMENT
X1/Z1
Z
X1
[DPTn]
X2/Z2
Z1
X2
DATA FOR READING
Z2
o
*9
DEPARTMENT
XX [DEPT#]
o
XX = DEPT CODE (2 digit) *9
CID
[X]
o
*9
PAID TOTAL
[SBTL]
o
*9
*1 MODE: X: Daily operator X report
*6 When the cashier code is not entered, the individual cashier report
is issued for all cashiers. And when cashier code is entered, the
individual cashier report is issued about the cashier.
Z: Daily operator Z report
X1: Daily X report
Z1: Daily Z report
X2: Periodic X report
Z2: Periodic Z report
Reading
(X report) : The corresponding data is held in the ECR.
(Z report) : The corresponding data is cleared in the ECR.
Assigned cashier
JOB#
@/FOR
CASHIER CODE
*2 To read respective reports, it is necessary to follow the procedure
below.
*7 When CCD is COMPULSORY for ALL CASHIERS:
Until ALL CASHIER RESETTING is done, any other reports that
reports the CID totals can not be executed.
The key sequence for the ALL CASHIER RESETTING are uniqure
and are outlined below.
Reading
(X report)
JOB#
@/FOR
CA/AT
Resetting
(Z report)
In case of Compulsory CCD for the INDIVIDUAL CASHIER:
Until ALL CASHIER RESETTING is done, any other reports that
reports the CID totals can not be executed.
The key sequence for the INDIVIDUAL CASHIER RESETTING is
unique and is outlined below.
*3 To read respective reports, it is necessary to follow the procedure
below.
Reading
(X report)
JOB#
CA/AT
4 digit
Resetting
<CCD ENTRY>
@/FOR
DATA
CA/AT
JOB#
Resetting
(Z report)
@/FOR
CA/AT
#
(DATA): GROUP No. (2 digit) (1-9)
CONV1
DEPT CODE (2 digit)
Q'ty
@/FOR
Amount
VOID
CA/AT
CONV2
*4 Report range can be specified by entering the starting and ending
numbers according to the following procedure.
CONV3
Repeat
*
#
Reading
CONV1
Amount
JOB#
CONV2
@/FOR
Resetting
CONV3
All
SBTL
Start = End
START NO.
@/FOR
END NO.
CA/AT
*: [#] is used for CASH and CHECK amount entry.
(START NO.) and (END NO.): PLU CODE (6 digit)
PRICE (6 digit)
TIME (2digit) (24-hour entry in spite
of TIME SYSTEM)
PBLU CODE (4 digit)
**: The total CASH and CHECK amount entered by [#] can be displayed by [SBTL].
*5 Individual cashier report prints the totals for the assigned cashier.
ER-A410U/A420U
OP X/Z, X1/Z1, X2/Z2 MODE
3–2
[Action]
*8 The stacked report function enables different reports to be printed
successively with a single reporting operation.
Individual counters for the following Z reports are incremented when
those reports are printed.
The programming for the stacked reports can be accomplished by
performing the following key operation in the PGM2 mode.
1) General daily total report (Z1)
2620
2) General periodic total report (Z2)
@/FOR
3) Hourly report (Z1)
ALL DELETE
4) Daily net total report (Z2)
NO RANGE
5) PLU report (Z1/Z2)
6) Individual Cashier and All Cashier report (Z1/Z2)
@/FOR
@/FOR
XX
SSSSSS
JOB No.
START CODE
EEEEEE
SBTL
END CODE
CA/AT
[Additional function]
NEXT JOB
(1) Secret code entry
When printing reports in the X1/Z1 mode and X2/Z2 mode, if a
secret code has been preset, the code must be entered prior to performing key operation to take reports.
Stacked reports can be printed by performing the following key
operation in the X1/Z1 and X2/Z2 modes.
Reading
x90
@/FOR
The secret code can be entered following the procedure shown
below.
CA/AT
Resetting
XXX
CA/AT
CA/AT
Secret code
If an ineligible job code of a report within the stacked report preset
is programmed, it is ignored (that report is not printed).
(2) Overflow mark
If the amount or quantity in any totalizer other than the GT to be
printed on an X or Z reports exceeds a programmed limit, the indication mark (overflow mark) is printed for the totalizer concerned.
Also, if stacked reports include any other reports for which a Z reports
can not be taken, the reports are ignored and are not printed.
A maximum of 15 different reports can be printed successively with
a single reporting operation.
Those 15 reports can include those reports that are identical in
code number. In this case, however, if any data changes due to the
printing of the previous report, the changed data is printed on the
following report.
Consecutive number: The counter is incremented by one.
Data is reset to zero.
AMOUNT:
Max. 9 (-999999999~+999999999)
(3) MODE TITLE
Each report prints a MODE TITLE at a header of report.
The Report Titles are as follows.
*9 Reading display only.
The displayed amount can be cleared by [CL] key.
KEY
(Display amount)
Max. 7 (-9999999~+9999999)
The overflow mark may be printed even if a totalizer does not reach
the maximum amount. This occurs, for example, when the amount
or quantity in the totalizer gets smaller than the maximum amount
due to the entry of a negative amount after the overflowing of the
totalizer. This means that when the totalizer overflows once, the
overflow mark (for example, “!!”) is printed.
For example:
Z report:
Q’TY:
CL
(Display initialize)
OPX report
#051 *OPX*
OPZ report
#051 *OPZ*
X1 report
#151 *X 1*
Z1 report
#151 *Z 1*
X2 report
#251 *X 2*
Z2 report
#251 *Z 2*
(4) Report cancel function
All report printing can be stopped.
Printing can be cancelled by turning the mode switch to MGR position while the data is printing. (In this case, the contents of memory
are not cleared.)
<Print sample of Report cancel>
:
:
*
*
*
*
*
123456789012345678901234
ER-A410U/A420U
OP X/Z, X1/Z1, X2/Z2 MODE
3–3
1 the report cancel symbol
q
COPYRIGHT  2002 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Digital Document Systems Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2002 August Printed in Japan t
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising