Casa (S) Pte Ltd. | WF 8101-A | User manual | Casa (S) Pte Ltd. WF 8101-A User manual

Casa (S) Pte Ltd. WF 8101-A User manual
Washing Machine
WF 8101-A
THE BEAUTY OF SIMPLICITY
USER MANUAL
1 Important safety instructions
• Follow the instructions on the textile tags and on
This section contains safety instructions that will
help protect from risk of personal injury or property
damage. Failure to follow these instructions shall
void any warranty.
General safety
• This product should not be used by persons
with physical, sensory or mental disorders or
unlearned or inexperienced people (including
children) unless they are attended by a person
who will be responsible for their safety or who
will instruct them accordingly for use of the
product.
• Never place the product on a carpet-covered
floor; otherwise, lack of airflow beneath the
machine will cause electrical parts to overheat.
This will cause problems with your product.
• Do not operate the product if the power cable /
plug is damaged. Call the Authorized Service
Agent.
• Have a qualified electrician connect a 16-Ampere
fuse to the installation location of the product.
• If the product has a failure, it should not be
operated unless it is repaired by the Authorized
Service Agent. There is the risk of electric
shock!
• This product is designed to resume operating
in the event of powering on after a power
interruption. If you wish to cancel the
programme, see "Cancelling the programme"
section.
• Connect the product to a grounded outlet
protected by a fuse complying with the values
in the "Technical specifications" table. Do not
neglect to have the grounding installation made
by a qualified electrician. Our company shall
not be liable for any damages that will arise
when the product is used without grounding in
accordance with the local regulations.
• The water supply and draining hoses must be
securely fastened and remain undamaged.
Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter
while there is still water in the drum. Otherwise,
risk of flooding and injury from hot water will
occur.
• Do not force open the locked loading door. The
loading door will be ready to open just a few
minutes after the washing cycle comes to an
end. In case of forcing the loading door to
open, the door and the lock mechanism may
get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring
water onto it! There is the risk of electric shock!
• Never touch the plug with wet hands! Never
unplug by pulling on the cable, always pull out
by grabbing the plug.
• Use detergents, softeners and supplements
suitable for automatic washing machines only.
2
the detergent package.
• The product must be unplugged during
installation, maintenance, cleaning and repairing
procedures.
• Always have the installation and repairing
procedures carried out by the Authorized
Service Agent. Manufacturer shall not be
held liable for damages that may arise from
procedures carried out by unauthorized
persons.
Intended use
• This product has been designed for domestic
use. It is not suitable for commercial use and it
must not be used out of its intended use.
• The product must only be used for washing and
rinsing of laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen
from incorrect usage or transportation.
Children's safety
• Electrical products are dangerous for the children.
Keep children away from the product when it
is in use. Do not let them to tamper with the
product. Use child lock to prevent children from
intervening with the product.
• Do not forget to close the loading door when
leaving the room where the product is located.
• Store all detergents and additives in a safe place
away from the reach of the children.
2 Installation
Refer to the nearest Authorised Service Agent for
installation of the product. To make the product
ready for use, review the information in the user
manual and make sure that the electricity, tap water
supply and water drainage systems are appropriate
before calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber to
have any necessary arrangements carried out.
of the location and electrical, tap
C Preparation
water and waste water installations at the place
of installation is under customer's responsibility.
Installation and electrical connections of the
B product
must be carried out by the Authorized
Service Agent. Manufacturer shall not be
held liable for damages that may arise from
procedures carried out by unauthorized
persons.
Prior to installation, visually check if the product
A has
any defects on it. If so, do not have it
installed. Damaged products cause risks for
your safety.
sure that the water inlet and discharge
C Make
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
Appropriate installation location
• Place the machine on a rigid floor. Do not place it
on a long pile rug or similar surfaces.
EN
• Total weight of the washing machine and the
dryer -with full load- when they are placed
on top of each other reaches to approx. 180
kilograms. Place the product on a solid and flat
floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where
temperature may fall below 0ºC.
• Place the product at least 1 cm away from the
edges of other furniture.
laundry.
1.Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water
inlet.
Removing packaging reinforcement
Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Removing the transportation locks
Do not remove the transportation locks before
A taking
out the packaging reinforcement.
Remove
transportation safety bolts before
A operatingthe
the washing machine, otherwise, the
product will be damaged.
1.Loosen all the bolts with a spanner until they
rotate freely (C).
2.Remove transportation safety bolts by turning
them gently.
3.Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel. (P)
the transportation safety bolts in a safe
C Keep
place to reuse when the washing machine
needs to be moved again in the future.
Never
move the product without the
C transportation
safety bolts properly fixed in
place!
Connecting water supply
water supply pressure required to run
C The
the product is between 1 to 10 bars (0.1 – 10
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
you are going to use the double water-inlet
C Ifproduct
as a single (cold) water-inlet unit, you
must install the supplied stopper to the hot
water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
you want to use both water inlets of the
C Ifproduct,
connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
Models with a single water inlet should not be
A connected
to the hot water tap. In such a case
the laundry will get damaged or the product will
switch to protection mode and will not operate.
Do not use old or used water inlet hoses on
A the
new product. It may cause stains on your
3
Ensure that the cold and hot water connections
A are
made correctly when installing the product.
Otherwise, your laundry will come out hot at the
end of the washing process and wear out.
2.Tighten all hose nuts by hand. Never use a
wrench when tightening the nuts.
3.Open the taps completely after making the hose
connection to check for water leaks at the
connection points. If any leaks occur, turn off
the tap and remove the nut. Retighten the nut
carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not
in use.
Connecting to the drain
• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
Your house will be flooded if the hose comes
A out
of its housing during water discharge.
Moreover, there is risk of scalding due to
high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come
out.
• The hose should be attached to a height of at
least 40 cm, and 100 cm at most.
• In case the hose is elevated after laying it on the
floor level or close to the ground (less than
40 cm above the ground), water discharge
becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the
heights described in the figure.
EN
Do not use any tools to loosen the lock nuts.
A Otherwise,
they will get damaged.
Electrical connection
• To prevent flowing of dirty water back into the
machine and to allow for easy discharge, do
not immerse the hose end into the dirty water
or drive it in the drain more than 15 cm. If it is
too long, cut it short.
• The end of the hose should not be bent, it should
not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by
adding an original extension hose. Length
of the hose may not be longer than 3.2 m.
To avoid water leak failures, the connection
between the extension hose and the drain
hose of the product must be fitted well with an
appropriate clamp as not to come off and leak.
Adjusting the feet
In order to ensure that the product operates
A more
silent and vibration-free, it must stand
Connect the product to a grounded outlet protected
by a fuse complying with the values in the "Technical
specifications" table. Our company shall not be
liable for any damages that will arise when the
product is used without grounding in accordance
with the local regulations.
• Connection must comply with national
regulations.
• Power cable plug must be within easy reach after
installation.
• The voltage and allowed fuse or breaker
protection are specified in the “Technical
specifications” section. If the current value of
the fuse or breaker in the house is less than 16
Amps, have a qualified electrician install a 16
Amp fuse.
• The specified voltage must be equal to your
mains voltage.
• Do not make connections via extension cables or
multi-plugs.
Damaged power cables must be replaced by
B the
Authorized Service Agents.
First use
Before starting to use the product, make sure
that all preparations are made in accordance
with the instructions in sections "Important safety
instructions" and "Installation".
To prepare the product for washing laundry, perform
first operation in Drum Cleaning programme. If
your machine is not featured with Drum Cleaning
programme, use Cottons-90 programme and select
Additional Water or Extra Rinse auxiliary functions
as well. Before starting the programme, put max.
100 g of powder anti-limescale into the main wash
detergent compartment (compartment nr. II). If the
anti-limescale is in tablet form, put only one tablet
into compartment nr. II. Dry the inside of the bellow
with a clean piece of cloth after the programme has
come to an end.
level and balanced on its feet. Balance the
machine by adjusting the feet. Otherwise, the
product may move from its place and cause
crushing and vibration problems.
1.Loosen the lock nuts on the feet by hand.
2.Adjust the feet until the product stands level and
balanced.
3.Tighten all lock nuts again by hand.
an anti-limescale suitable for the washing
C Use
machines.
water might have remained in the
C Some
product due to the quality control processes in
the production. It is not harmful for the product.
Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place away from
reach of the children.
4
EN
Packaging materials of the product are
manufactured from recyclable materials. Dispose of
them properly and sort in accordance with recycled
waste instructions. Do not dispose of them with
normal domestic waste.
Transportation of the product
Unplug the product before transporting it. Remove
water drain and water supply connections. Drain
the remaining water in the product completely; see,
"Draining remaining water and cleaning the pump
filter". Install transportation safety bolts in the reverse
order of removal procedure; see, "Removing the
transportation locks".
move the product without the
C Never
transportation safety bolts properly fixed in
place!
Disposing of the old product
Dispose of the old product in an environmentally
friendly manner.
Refer to your local dealer or solid waste collection
centre in your area to learn how to dispose of your
product.
For children's safety, cut the power cable and break
the locking mechanism of the loading door so
that it will be nonfunctional before disposing of the
product.
3 Preparation
Things to be done for energy saving
Following information will help you use the product in
an ecological and energy-efficient manner.
• Operate the product in the highest capacity
allowed by the programme you have selected,
but do not overload; see, "Programme and
consumption table".
• Always follow the instructions on the detergent
packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of
lightly soiled laundry.
• Do not use prewash and high temperatures for
laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select
the highest spin speed recommended during
washing process.
• Do not use detergent in excess of the amount
recommended on the detergent package.
Sorting the laundry
• Sort laundry according to type of fabric, colour,
and degree of soiling and allowable water
temperature.
• Always obey the instructions given on the garment
tags.
damage the product or cause noise problem.
• Put small size clothes such as infant's socks and
nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them.
Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips
and tears.
• Wash “machine washable” or “hand washable”
labeled products only with an appropriate
programme.
• Do not wash colours and whites together. New,
dark coloured cottons release a lot of dye.
Wash them separately.
• Tough stains must be treated properly before
washing. If unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale
removers suitable for machine wash. Always
follow the instructions on the package.
• Wash trousers and delicate laundry turned inside
out.
• Keep laundry items made of Angora wool in the
freezer for a few hours before washing. This will
reduce pilling.
• Laundry that are subjected to materials such as
flour, lime dust, milk powder, etc. intensely must
be shaken off before placing into the machine.
Such dusts and powders on the laundry may
build up on the inner parts of the machine in
time and can cause damage.
Correct load capacity
The maximum load capacity depends on the type
of laundry, the degree of soiling and the washing
programme desired.
The machine automatically adjusts the amount of
water according to the weight of the loaded laundry.
Follow the information in the “Programme
A and
consumption table”. When overloaded,
machine's washing performance will drop.
Moreover, noise and vibration problems may
occur.
Loading the laundry
• Open the loading door.
• Place laundry items loosely into the machine.
• Push the loading door to close until you hear a
locking sound. Ensure that no items are caught
in the door.
loading door is locked while a programme
C The
is running. The door can only be opened a
while after the programme comes to an end.
In case of misplacing the laundry, noise and
A vibration
problems may occur in the machine.
Preparing laundry for washing
• Laundry items with metal attachments such as,
underwired bras, belt buckles or metal buttons
will damage the machine. Remove the metal
pieces or wash the clothes by putting them in a
laundry bag or pillow case.
• Take out all substances in the pockets such as
coins, pens and paper clips, and turn pockets
inside out and brush. Such objects may
5
EN
Using detergent and softener
Detergent Drawer
The detergent drawer is composed of three
compartments:
- (I) for prewash
- (II) for main wash
– (III) for softener
– ( )in addition, there is siphon piece in the softener
compartment.
II
III
I
III
II
I
The detergent dispenser may be in two different
types according to the model of your machine
as seen above.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the
washing programme.
• Never open the detergent drawer while the
washing programme is running!
• When using a programme without prewash,
do not put any detergent into the prewash
compartment (compartment nr. I).
• In a programme with prewash, do not put liquid
detergent into the prewash compartment
(compartment nr. I).
• Do not select a programme with prewash if you
are using a detergent bag or dispensing ball.
Place the detergent bag or the dispensing ball
directly among the laundry in the machine.
• If you are using liquid detergent, do not forget to
place the liquid detergent cup into the main
wash compartment (compartment nr. II).
Choosing the detergent type
The type of detergent to be used depends on the
type and colour of the fabric.
• Use different detergents for coloured and white
laundry.
• Wash your delicate clothes only with special
detergents (liquid detergent, wool shampoo,
etc.) used solely for delicate clothes.
• When washing dark coloured clothes and quilts, it
is recommended to use liquid detergent.
• Wash woolens with special detergent made
specifically for woolens.
Use only detergents manufactured specifically
for washing machines.
Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used
depends on the amount of laundry, the degree of
soiling and water hardness. Read the manufacturer's
instructions on the detergent package carefully and
follow the dosage values.
• Do not use amounts exceeding the dosage
quantities recommended on the detergent
package to avoid problems of excessive
6
foam, poor rinsing, financial savings and finally,
environmental protection.
• Use lesser detergent for small amounts or lightly
soiled clothes.
• Use concentrated detergents in the
recommended dosage.
Using softeners
Pour the softener into the softener compartment of
the detergent drawer.
• Use the dosages recommended on the package.
• Do not exceed the (>max<) level marking in the
softener compartment.
• If the softener has lost its fluidity, dilute it with water
before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
• Make sure that you have placed the liquid
detergent cup in compartment nr. "II".
• Use the detergent manufacturer's measuring cup
and follow the instructions on the package.
• Use the dosages recommended on the package.
• If the liquid detergent has lost its fluidity, dilute it
with water before putting in the detergent cup.
If the product does not contain a liquid
detergent cup:
• Do not use liquid detergent for the prewash in a
programme with prewash.
• Use the detergent manufacturer's measuring cup
and follow the instructions on the package.
• Liquid detergent stains your clothes when used
with Delayed Start function. If you are going to
use the Delayed Start function, do not use liquid
detergent.
Using gel and tablet detergent
When using tablet, gel, etc. detergents, read the
manufacturer's instructions on the detergent
package carefully and follow the dosage values. If
there is not any instruction on the package, apply
the following.
• If the gel detergent thickness is fluidal and your
machine does not contain a special liquid
detergent cup, put the gel detergent into the
main wash detergent compartment during first
water intake. If your machine contains a liquid
detergent cup, fill the detergent into this cup
before starting the programme.
• If the gel detergent thickness is not fluidal or in the
shape of capsule liquid tablet, put it directly into
the drum before washing.
• Put tablet detergents into the main wash
compartment (compartment nr. II) or directly
into the drum before washing.
Tablet detergents may leave residues in the
detergent compartment. If you encounter such
a case, place the tablet detergent between the
EN
laundry, close to the lower part of the drum in
future washings.
Use
the tablet or gel detergent without
C selecting
the prewash function.
Using starch
• Add liquid starch, powder starch or the dyestuff
into the softener compartment as instructed
on the package.
• Do not use softener and starch together in a
washing cycle.
• Wipe the inside of the machine with a damp and
clean cloth after using starch.
Using bleaches
• Select a programme with prewash and add
the bleaching agent at the beginning of
the prewash. Do not put detergent in the
prewash compartment. As an alternative
application, select a programme with extra
rinse and add the bleaching agent while the
machine is taking water from the detergent
compartment during first rinsing step.
• Do not use bleaching agent and detergent by
mixing them.
• Use just a little amount (approx. 50 ml) of
bleaching agent and rinse the clothes very
well as it causes skin irritation. Do not pour
the bleaching agent onto the clothes and do
not use it for coloured clothes.
• When using oxygen based bleaches, follow
the instructions on the package and select
a programme that washes at a lower
temperature.
• Oxygen based bleaches can be used together
with detergents; however, if its thickness is
not the same with the detergent, put the
detergent first into the compartment nr. "II"
in the detergent drawer and wait until the
detergent flows while the machine is taking
in water. Add the bleaching agent from the
same compartment while the machine is still
taking in water.
Using limescale remover
• When required, use limescale removers
manufactured specifically for washing
machines only.
• Always follow instructions on the package.
7
EN
4 Operating the product
Control panel
1
6
1 -
2 -
3 -
4 -
2
3
7
8
4
Spin Speed Adjustment button
Display
Temperature Adjustment button
Programme Selection knob
5 -
6 -
7 -
8 -
Display symbols
5
On / Off button
Delayed Start buttons (+ / -)
Auxiliary Function buttons
Start / Pause / Cancel button
Preparing the machine
Make sure that the hoses are connected tightly. Plug
in your machine. Turn the tap on completely. Place
the laundry in the machine. Add detergent and
fabric softener.
Programme selection
1.Select the programme suitable for the type,
quantity and soiling degree of the laundry
in accordance with the "Programme and
consumption table" and the temperature table
below.
F1
a
b
c
d
e
F2
F3
F4
-
-
-
-
-
Spin Speed indicator
Temperature indicator
Spin symbol
Temperature symbol
Remaining Time and Delayed Start
indicator
f
- Programme Indicator symbols (Prewash /
Main Wash / Rinse / Softener / Spin)
g
- Economy symbol
h
- Delayed Start symbol
i
- Door Locked symbol
j
- Start symbol
k
- Pause symbol
l
- Auxiliary Function symbols
m- No Water symbol
8
90˚C
Heavily soiled white cottons and linens.
(coffee table covers, tableclothes,
towels, bed sheets, etc.)
60˚C
Normally soiled, coloured, fade proof
cottons or synthetic clothes (shirt,
nightgown, pajamas, etc.) and lightly
soiled white linens (underwear, etc.)
40˚C30˚CCold
Blended laundry including delicate
textile (veil curtains, etc.), synthetics and
woolens.
2.Select the desired programme with the
Programme Selection button.
Programmes
are limited with the highest spin
C speed appropriate
for that particular type of
fabric.
selecting a programme, always consider
C When
the type of fabric, colour, degree of soiling and
permissible water temperature.
EN
Always select the lowest required temperature.
Higher temperature means higher power
consumption.
For further programme details, see "Programme
and consumption table".
Main programmes
Depending on the type of fabric, use the following
main programmes.
• Cottons (Algodón)
Use this programme for your cotton laundry (such
as bed sheets, duvet and pillowcase sets, towels,
bathrobes, underwear, etc.). Your laundry will be
washed with vigorous washing action for a longer
washing cycle.
• Synthetics (Sintéticos)
Use this programme to wash your synthetic
clothes (shirts, blouses, synthetic/cotton blends,
etc.). It washes with a gentle action and has a
shorter washing cycle compared to the Cottons
programme.
For curtains and tulle, use the Synthetic 40˚C
programme with prewash and anti-creasing
functions selected. As their meshed texture causes
excessive foaming, wash the veils/tulle by putting
little amount of detergent into the main wash
compartment. Do not put detergent in the prewash
compartment.
• Woollens (Lana)
Use this programme to wash your woolen clothes.
Select the appropriate temperature complying with
the tags of your clothes. Use appropriate detergents
for woolens.
Additional programmes
For special cases, additional programmes are
available in the machine.
Additional programmes may differ according to
the model of the machine.
• Cotton Eco (Algodón Eco)
Use this programme to wash your laundry washable
in cottons programme for a longer time, still with a
very good performance for saving purposes.
Cottons Eco programme consumes less energy
compared to other cottons programmes.
• Intensive (Intensivo)
Use this programme to wash baby laundry, and the
laundry that belongs to allergic persons. Longer
heating time and an additional rinsing step provide a
higher level of hygiene.
• Delicate (Delicado)
Use this programme to wash your delicate clothes. It
washes with a gentle action without any interim spin
compared to the Synthetics programme.
• Hand Wash (Lavado a mano)
Use this programme to wash your woolen/delicate
clothes that bear “not machine- washable” tags and
for which hand wash is recommended. It washes
laundry with a very gentle washing action to not to
damage clothes.
• Quick (Rápido)
Use this programme to wash your lightly soiled
cotton clothes in a short time.
9
• Eco 40
Use this programme to wash your laundry for which
you cannot use Cottons 60 °C programme. It gives
the same result with the Cottons 60 °C programme
by washing for a longer time at 40 °C, thus enabling
energy saving.
• Mixed 40 (Mezcla 40)
Use this programme to wash your cotton and
synthetic clothes together without sorting them.
• Intensive+ (Intensivo+)
You can wash your durable and heavily soiled
clothes on this program. In this program, your
clothes will be washed for a longer time and an extra
rinse cycle will be made compared to the “Cottons”
program. You can use it for your heavily soiled
clothes that you wish to be rinsed gently.
• Curtain (Cortinas)
Use this programme to wash your tulles and
curtains. Thanks to the special spin profile of the
programme, tulles and curtains crease lesser.
As their meshed texture causes excessive foaming,
wash the veils/tulle by putting little amount of
detergent into the main wash compartment. Do
not put detergent in the prewash compartment.
Prewash is used to clean the dirt (dust, sooth, etc.)
on the tulles / curtains that can be removed easily.
It is suggested to use recommended
detergents for curtains in this programme.
• Refresh (Diario)
Use this programme to remove the odour on the
laundry that are worn only for once and do not
contain any stains or dirt.
• Cotton 20 (Algodón 20)
Use this programme, which is much more sensitive
to environment and natural resources, to wash your
lightly soiled and unstained cotton laundry (max. 3.5
kg) in a short time and economically.
It is recommended to use liquid detergent or gel
washing detergent.
Special programmes
For specific applications, select any of the following
programmes.
• Rinse (Enjuague)
Use this programme when you want to rinse or
starch separately.
• Pump+Spin (Drenar+Centrifugado)
Use this programme to apply an additional spin
cycle for your laundry or to drain the water in the
machine.
Before selecting this programme, select the desired
spin speed and press Start / Pause / Cancel button.
The machine will spin the laundry with the set spin
speed and drain the water coming out of them.
If you wish to drain only the water without spinning
your laundry, select the Pump+Spin programme
and then select the No Spin function with the help of
Spin Speed Adjustment button. Press Start / Pause
/ Cancel button.
Use a lower spin speed for delicate laundries.
Temperature selection
Whenever a new programme is selected, the
maximum temperature for the selected programme
EN
appears on the temperature indicator.
To decrease the temperature, press the
Temperature Adjustment button. Temperature
decreases with increments of 10° and finally, “-”
symbol indicating the cold wash option appears
on the display.
you scroll to cold wash option and press
CIfTemperature
Adjustment button again, the
recommended temperature for the selected
programme appears on the display. Press
the Temperature Adjustment button again to
decrease the temperature.
Economy symbol
Indicates the programmes and temperatures that
provide energy savings.
symbol can not be selected in
CEconomy
Intensive and Hygiene programmes since
washing is performed in long times and
at high temperatures in order to provide
hygiene. Similarly, Economy symbol can not
be selected in Baby, Refresh, Drum Cleaning,
Spin and Rinse programmes as well.
Spin speed selection
Whenever a new programme is selected, the
recommended spin speed of the selected
programme is displayed on the spin speed
indicator.
To decrease the spin speed, press the Spin
Speed Adjustment button. Spin speed decreases
gradually. Then, depending on the model of the
product, "Rinse Hold" and "No Spin" options
appear on the display. See "Auxiliary function
selection" section for explanations of these
options.
Hold option is indicated with “
”
CRinse
symbol and No Spin option is indicated with “
” symbol.
10
EN
Programme and consumption table
Temperature
Selectable
temperature
range℃
Cottons
90
8
82 2.70
1200
•
•
•
•
•
90-Cold
Cottons
60
8
80 1.80
1200
•
•
•
•
•
90-Cold
Cottons
40
8
80
1.00
1200
•
•
•
•
•
90-Cold
Cotton Eco
60**
8
59
1.36
1200
•
•
•
•
•
60-Cold
Cotton Eco
40
8
72
0.75
1200
•
•
•
•
•
60-Cold
Intensive
40
60
0.60
1000
Intensive+
90
8
73
2.70
1200
Synthetics
60
4
55
1.00
1000
•
•
•
•
•
60-Cold
Synthetics
40
4
55
0.52
1000
•
•
•
•
•
60-Cold
Eco
40
8
60
1.20
1200
40
Cotton 20
20
3.5
39
0.16
1200
20
Curtain
40
2
67
0.50
800
*
*
*
Mix
40
4
55
0.62
1000
•
•
•
•
Daily
40
4
45
0.60
1200
•
•
•
*
Quick
90
8
70
2.00
1200
•
90-Cold
Quick
60
8
70
1.15
1200
•
90-Cold
Quick
30
8
80
0.20
1200
•
Wollens
40
2
56
0.30
1000
•
Delicate
40
3
60
0.25
1000
•
Hand wash
20
1.5
40
0.25
1000
Prewash
Rinse Hold
Anti-Creasing
Rinse Plus
Quick Wash
Max Quick Wash***
Energy
Consumption(kWh)
Program (°C)
Water Consumption(I)
Auxiliary functions
Max. Load(kg)
EN
60-40
*
90-30
40-Cold
•
40-Cold
60-Cold
90-Cold
•
•
40-Cold
•
40-Cold
20
• : Selectable
* : Automatically selected, no canceling.
** : Energy Label programme (EN 60456 Ed.3)
*** : If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.
** “Cotton eco 40°C and Cotton eco 60°C are standard cycles.” These cycles are known as ‘40°C cotton standard cycle’ and
‘60°C cotton standard cycle’ and indicated with the
symbols on the panel.
The auxiliary functions in the table may vary according to the model of your machine.
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient
temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage.
You can see the washing time of the programme you have selected on the display of the machine. It is normal that small
differences may occur between the time shown on the display and the real washing time.
11
EN
Auxiliary function selection
Select the desired auxiliary functions before starting
the programme. Furthermore, you may also select
or cancel auxiliary functions that are suitable to the
running programme by pressing the Start / Pause
/ Cancel button when the machine is operating.
For this, the machine must be in a step before the
auxiliary function you are going to select or cancel.
Depending on the programme, press 2a, 2b, 2c or
2d buttons to select the desired auxiliary function.
Symbol of the selected auxiliary function appears on
the display.
functions cannot be selected together. If
C Some
a second auxiliary function conflicting with the
first one is selected before starting the machine,
the function selected first will be canceled
and the second auxiliary function selection
will remain active. For example, if you want to
select Quick Wash after you have selected the
Prewash, Prewash will be canceled and Quick
Wash will remain active.
auxiliary function that is not compatible
C An
with the programme cannot be selected. (See
"Programme and consumption table")
C Auxiliary Function buttons may vary according
to the model of the machine.
• Prewash (Prelavado)
A Prewash is only worthwhile for heavily soiled
laundry. Not using the Prewash will save energy,
water, detergent and time.
F1 appears on the display when you select this
function (a).
• Quick Wash
This function can be used in Cottons and Synthetics
programmes. It decreases the washing times and
also the number of rinsing steps for lightly soiled
laundry.
F2 appears on the display when you select this
function (b).
you select this function, load your
C When
machine with half of the maximum laundry
specified in the programme table.
• Extra Rinse (Extra Arrugas)
This function enables the machine to make another
rinsing in addition to the one already made after the
main wash. Thus, the risk for sensitive skins (babies,
allergic skins, etc.) to be effected by the minimal
detergent remnants on the laundry can be reduced.
F3 appears on the display when you select this
function (c).
• Anti-creasing (Antiarrugas)
This function creases the clothes lesser when they
are being washed. Drum movement is reduced and
spinning speed is limited to prevent creasing. In
addition, washing is done with a higher water level.
F4 appears on the display when you select this
function (d).
• Rinse Hold
If you are not going to unload your clothes
immediately after the programme completes, you
12
may use rinse hold function to keep your laundry
in the final rinsing water in order to prevent them
from getting wrinkled when there is no water in the
machine. Press Start / Pause / Cancel button after
this process if you want to drain the water without
spinning your laundry. Programme will resume and
complete after draining the water.
If you want to spin the laundry held in water, adjust
the Spin Speed and press Start / Pause / Cancel
button.
The programme resumes. Water is drained, laundry
is spun and the programme is completed.
• Soaking
The Soaking auxiliary function ensures better
removal of stains ingrained into the clothes by
holding them in the detergent water prior to startup
of the programme.
Time display
Remaining time to complete the programme
appears on the display while the programme is
running. Tim is displayed as “01:30” in hours and
minutes format.
time may differ from the values
C Programme
in the "Programme and consumption
table" depending on the water pressure,
water hardness and temperature, ambient
temperature, amount and the type of laundry,
auxiliary functions selected and the changes at
the mains voltage.
Delayed start
With the Delayed Start function the startup of
the programme may be delayed up to 24 hours.
Delayed start time can be increased by increments
of 30 minutes.
not use liquid detergents when you set
C Do
Delayed Start! There is the risk of staining of the
clothes.
Open the loading door, place the laundry and put
detergent, etc. Select the washing programme,
temperature, spin speed and, if required, the auxiliary
functions. Set the desired delayed start time by
pressing the Delayed Start + or - buttons. Delayed
Start symbol flashes. Press Start / Pause / Cancel
button. Delayed start countdown starts. Delayed
Start symbol illuminates steadily. Start symbol
appears. “:” sign in the middle of the delayed start
time on the display starts flashing.
laundry may be loaded during
C Additional
the delayed start period. At the end of the
countdown, Delayed Start symbol disappears,
washing cycle starts and the time of the
selected programme appears on the display.
Changing the delayed start period
If you want to change the time during countdown:
Press Start / Pause / Cancel button. “:” sign in the
middle of the delayed start time on the display stops
flashing. Pause symbol appears. Delayed Start
symbol flashes. Start symbol disappears. Set the
desired delayed start time by pressing the Delayed
Start + or - buttons. Press Start / Pause / Cancel
button. Delayed Start symbol illuminates steadily.
Pause symbol disappears. Start symbol appears.
EN
“:” sign in the middle of the delayed start time on the
display starts flashing.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown
and start the programme immediately:
Press Start / Pause / Cancel button. “:” sign in the
middle of the delayed start time on the display stops
flashing. Start symbol disappears. Pause symbol
and Delayed Start symbol flashes. Decrease the
delayed start time by pressing the Delayed Start
- button. Programme duration appears after 30
minutes. Press Start / Pause / Cancel button to start
the programme.
Starting the programme
Press Start / Pause / Cancel button to start the
programme. Start symbol showing the startup of
the programme will turn on. Loading door is locked
and Door Locked symbol appears on the display.
The symbol of the step from which the programme
has started appears on the display (Prewash, Main
Wash, Rinse, Softener and Spin).
Progress of programme
Progress of a running programme is indicated on the
display with a set of symbols.
Relevant symbol appears on the display at
the beginning of each programme step and all
symbols remain lit at the end of the programme.
The farthermost right symbol indicates the current
programme step.
Prewash
If the Prewash auxiliary function is selected, Prewash
symbol appears on the display indicating that the
prewash step has started.
Main Wash
Main Wash symbol indicating that the main wash
step has started appears on the display.
Rinse
Rinse symbol indicating that the rinsing step has
started appears on the display.
Softener
Softener symbol indicating that the softener step has
started appears on the display.
Spin
Appears at the beginning of the final spin step
and remains lit during Spin and Pump special
programmes.
the machine does not pass to the spinning
C Ifstep,
Rinse Hold function might be active or the
automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
Door Locked symbol appears when the loading
door is locked. This symbol will flash until the loading
door becomes ready to open when programme
completes or the machine is paused. Do not force
to open the loading door in this step. Symbol
disappears when the door is ready to open. You can
open the door when the symbol disappears.
13
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause / Cancel button to switch the
machine to pause mode. Pause symbol appears on
the display indicating that the machine is paused.
Start symbol disappears.
Changing the speed and temperature settings
for auxiliary functions
Depending on the step the programme has reached,
you may cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
Adding or taking out laundry
Press the Start / Pause / Cancel button to switch
the machine to pause mode. The programme
follow-up light of the relevant step during which the
machine was switched into the pause mode will
flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the
laundry. Close the Loading Door. Make changes in
auxiliary functions, temperature and speed settings
if necessary. Press Start / Pause / Cancel button to
start the machine.
loading door will not open if the water
C The
temperature in the machine is high or the water
level is above the door opening.
Child Lock
Use Child Lock function to prevent children from
tampering with the machine. Thus you can avoid any
changes in a running programme.
can switch on and off the machine with
C You
On / Off button when the Child Lock is active.
When you switch on the machine again,
programme will resume from where it has
stopped.
To activate the Child Lock:
Press and hold 2nd and 4th Auxiliary Function buttons
for 3 seconds. “Con” appears on the display.
phrase will appear on the display if you
C Same
press any button when Child Lock is enabled.
To deactivate the Child Lock:
Press and hold 2nd and 4th Auxiliary Function buttons
for 3 seconds. “COFF” appears on the display.
not forget to disable the child lock at the
C Do
end of the programme if it was enabled before.
Otherwise, machine will not allow to select a
new programme.
Canceling the programme
Press and hold Start / Pause / Cancel button for 3
seconds. Start symbol flashes. Symbol of the step
at which the programme was cancelled remains lit.
"END" appears on the display and the programme
is cancelled.
you want to open the loading door after you
C Ifhave
cancelled the programme but it is not
possible to open the loading door since the
water level in the machine is above the loading
EN
avoid touching of the residues in the drawer with
your skin when cleaning. Insert the drawer back
into its place after cleaning and make sure that it is
seated well.
door opening, then turn the Programme
Selection knob to Pump+Spin programme
and discharge the water in the machine.
Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates
when the machine is in Rinse Hold mode.
If you want to spin your laundry when the machine
is in this mode:
Adjust the spin speed and press Start / Pause
/ Cancel button. Pause symbol disappears and
Start symbol appears. Programme resumes,
discharges the water and spins the laundry.
If you only want to drain the water without spinning:
Just press Start / Pause / Cancel button. Pause
symbol disappears. Start symbol appears.
Programme resumes and discharges the water only.
Cleaning the water intake filters
There is a filter at the end of each water intake
valve at the rear of the machine and also at the
end of each water intake hose where they are
connected to the tap. These filters prevent foreign
substances and dirt in the water to enter the
washing machine. Filters should be cleaned as
they do get dirty.
End of programme
“End” appears on the display at the end of the
programme. Symbols of the programme steps
remain lit. Auxiliary function, spin speed and
temperature that were selected at the beginning of
the programme remain selected.
Your machine is equipped with
a “Standby Mode”
In case of not starting any programme or
waiting without making any other operation
when the machine is turned on by On/Off
button and while it is in selection step or if
no other operation is performed approximately
2 minutes after the programme you selected
has come to an end,your machine will
automatically switch to energy saving mode.
Display brightness will decrease. In case of
rotating the Programme Selection knob or
pressing any button, lights will restore to their
previous condition. This is not a fault.
Close the taps. Remove the nuts of the water
intake hoses to access the filters on the water
intake valves. Clean them with an appropriate
brush. If the filters are too dirty, take them out
by means of pliers and clean them. Take out the
filters on the flat ends of the water intake hoses
together with the gaskets and clean thoroughly
under running water. Replace the gaskets and
filters carefully in their places and tighten the hose
nuts by hand.
Draining remaining water and
cleaning the pump filter
5 Maintenance and cleaning
Service life of the product extends and frequently
faced problems decrease if cleaned at regular
intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular intervals
(every 4-5 washing cycles) as shown below
in order to prevent accumulation of powder
detergent in time.
Press the dotted point on the siphon in the
softener compartment and pull towards you until
the compartment is removed from the machine.
If more than normal amount of water and
softener mixture starts to gather in the softener
compartment, the siphon must be cleaned.
Wash the detergent drawer and the siphon with
plenty of lukewarm water in a washbasin. Wear
protective gloves or use an appropriate brush to
14
The filter system in your machine prevents solid
items such as buttons, coins and fabric fibers
clogging the pump impeller during discharge of
washing water. Thus, the water will be discharged
without any problem and the service life of the
pump will extend.
If the machine fails to drain water, the pump filter
is clogged. Filter must be cleaned whenever it
is clogged or in every 3 months. Water must be
drained off first to clean the pump filter.
In addition, prior to transporting the machine
(eg., when moving to another house) and in case
of freezing of the water, water may have to be
drained completely.
Foreign substances left in the pump filter may
damage your machine or may cause noise
problem.
In order to clean the dirty filter and discharge the
water:
Unplug the machine to cut off the supply power.
Temperature of the water inside the machine
may rise up to 90 ºC. To avoid burning risk,
filter must be cleaned after the water in the
machine cools down.
Open the filter cap.
If the filter cap is composed of two pieces, press
the tab on the filter cap downwards and pull
the piece out towards yourself.
EN
If the filter cap is one piece, pull the cap from both
sides at the top to open.
can remove the filter cover by slightly
C You
pushing downwards with a thin plastic tipped
tool, through the gap above the filter cover. Do
not use metal tipped tools to remove the cover.
Some of our products have emergency draining
hose and some does not have. Follow the steps
below to discharge the water.
Discharging the water when the product has an
emergency draining hose:
Pull the emergency draining hose out from its seat
Place a large container at the end of the hose. Drain
the water into the container by pulling out the plug at
the end of the hose. When the container is full, block
the inlet of the hose by replacing the plug. After the
container is emptied, repeat the above procedure
to drain the water in the machine completely. When
draining of water is finished, close the end by the
plug again and fix the hose in its place. Turn the
pump filter to take it out.
Discharging the water when the product does not
have an emergency draining hose:
Place a large container in front of the filter to
catch water from the filter. Loosen pump filter
(anticlockwise) until water starts to flow. Fill the
flowing water into the container you have placed in
front of the filter. Always keep a piece of cloth handy
to absorb any spilled water. When the water inside
the machine is finished, take out the filter completely
by turning it. Clean any residues inside the filter
as well as fibers, if any, around the pump impeller
region. Install the filter.
If your product has a water jet feature, be sure
A to
fit the filter into its housing in the pump.
Never force the filter while installing it into its
housing. Seat the filter into its place completely.
Otherwise, water may leak from the filter cap.
If the filter cap is composed of two pieces, close the
filter cap by pressing on the tab. If it is one piece,
seat the tabs in the lower part into their places first,
and then press the upper part to close.
15
EN
6 Technical specifications
Models
WA 8101-A
Maximum dry laundry capacity (kg)
Height (cm)
8
84
Width (cm)
60
Depth (cm)
56.5
70
Net weight (±4 kg.)
Electrical input (V/Hz)
220-240V~/50Hz
Total current (A)
10
Total power (W)
2000-2350W
Spin speed (rpm max.)
1200
Stand-by mode power(W)
1.00
Off-mode power(W)
0.20
Technical specifications may be changed without prior notice to improve the quality of the product.
Figures in this manual are schematic and may not match the product exactly.
Values stated on the product labels or in the documentation accompanying it are obtained in laboratory
conditions in accordance with the relevant standards. Depending on operational and environmental
conditions of the product, these values may vary.
This appliance’s packaging material is recyclable. Help recycle it and protect the
environment by dropping it off in the municipal receptacles provided for this purpose. Your
appliance also contains a great amount of recyclable material. It is marked with this label
to indicate the used appliances that should not be mixed with other waste. This way, the
appliance recycling organised by your manufacturer will be done under the best possible
conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment. Contact your town hall or your retailer for the used appliance
collection points closest to your home. We thank you doing your part to protect the
environment.
16
EN
7 Troubleshooting
Programme cannot be started or selected.
• Washing machine has switched to self protection mode due to a supply problem (line voltage, water
pressure, etc.). >>> Press and hold Start / Pause button for 3 seconds to reset the machine to
factory settings. (See "Canceling the programme")
Water in the machine.
• Some water might have remained in the product due to the quality control processes in the
production. >>> This is not a failure; water is not harmful to the machine.
Machine vibrates or makes noise.
• Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
• A hard substance might have entered into the pump filter. >>> Clean the pump filter.
• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
• Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
• Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or
distribute the load by hand to balance it homogenously in the machine.
• Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.
Machine stopped shortly after the programme started.
• Machine might have stopped temporarily due to low voltage. >>> It will resume running when the
voltage restores to the normal level.
Programme time does not countdown. (On models with display)
• Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes
in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid
poor washing results due to lack of water. Timer indicator will resume countdown after this.
• Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches
the selected temperature.
• Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be
activated due to the unbalanced distribution of the laundry in the drum.
Machine
not switch to spinning step when the laundry is not evenly distributed in the drum
C to preventdoes
any damage to the machine and to its surrounding environment. Laundry should be
rearranged and re-spun.
Foam is overflowing from the detergent drawer.
• Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main
wash compartment of the detergent drawer.
detergent into the machine suitable for the programmes and maximum loads indicated in the
C Put
“Programme and consumption table”. When you use additional chemicals (stain removers, bleachs
and etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme
• Excessive foam might have occurred and automatic foam absorption system might have been
activated due to too much detergent usage. >>> Use recommended amount of detergent.
does not switch to spinning step when the laundry is not evenly distributed in the drum
C Machine
to prevent any damage to the machine and to its surrounding environment. Laundry should be
rearranged and re-spun.
If you cannot eliminate the problem although you follow the instructions in this section, consult your
A dealer
or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.
17
EN
Casa (S) Pte Ltd. 15 Kian Teck Crescent, Singapore 628884.
Service Centre Hotline: 62680077.
Fax: 68980510.
Email: service@casa.com.sg
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising