Promethean | PRM-25 | Owner`s manual | promethean PRM-25 Owner`s manual

promethean PRM-25 Owner`s manual
Multimedia Projector
MODEL
PRM-25
PROJECTOR
Owner’s Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2009
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.
All other product names used in this manual are the properties of their respective owners and are acknowledged.
Promethean, Company Confidential
i
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
Promethean, Company Confidential
ii
Projector Installation Notice
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in
any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
Allow at least 50 cm clearance around the exhaust vent.
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed 5 – 35°C while the projector is running, and the air intake and
exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable 5 – 35°C range.
Power Safety
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Promethean, Company Confidential
iii
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 39
for clear and safe instructions for this procedure. Before replacing the lamp:
Unplug the power cord.
Allow the lamp to cool for about one hour.
Cleaning the Projector
Unplug the power cord before cleaning. See Cleaning the Projector on page 42.
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section
on page 53.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
Main Features
•
Lightweight unit, easy to pack away and transport.
•
Compatible with all major video standards including NTSC, PAL, and SECAM.
•
A high brightness rating allows for presentations in daylight or in lit rooms.
•
Supports resolutions up to SXGA+ at 16.7 million colors to deliver crisp, clear images.
•
Flexible setup allows for front, rear projections.
•
Line-of-vision projections remain square, with advanced keystone correction for angled
projections.
•
Input source automatically detected.
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting
the environment. It is suggested that you only print sections that are relevant to your needs.
Promethean, Company Confidential
iv
Table of Contents
GETTING STARTED .......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
PRM-25 Front-right View............................................................................................................................................... 2
Rear view ........................................................................................................................................................................ 3
Bottom view..................................................................................................................................................................... 4
REMOTE CONTROL PARTS ................................................................................................................................................... 5
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 7
PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 7
SETUP AND OPERATION................................................................................................................................................. 8
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................... 8
CONNECTING INPUT DEVICES .............................................................................................................................................. 9
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 10
SETTING AN ACCESS PASSWORD (SECURITY LOCK) .......................................................................................................... 12
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 14
ADJUSTING THE FOCUS AND KEYSTONE ............................................................................................................................ 15
ADJUSTING THE VOLUME .................................................................................................................................................. 16
ON-SCREEN DISPLAY (OSD) MENU SETTINGS....................................................................................................... 17
OSD MENU CONTROLS ..................................................................................................................................................... 17
Navigating the OSD ...................................................................................................................................................... 17
SETTING THE OSD LANGUAGE .......................................................................................................................................... 18
OSD MENU OVERVIEW ..................................................................................................................................................... 19
OSD SUB-MENU OVERVIEW ............................................................................................................................................. 20
IMAGE MENU ..................................................................................................................................................................... 21
Advanced Feature ......................................................................................................................................................... 22
Color Manager.............................................................................................................................................................. 23
COMPUTER MENU.............................................................................................................................................................. 24
VIDEO/AUDIO MENU ......................................................................................................................................................... 25
Audio............................................................................................................................................................................. 26
INSTALLATION I MENU ...................................................................................................................................................... 27
INSTALLATION II MENU .................................................................................................................................................... 28
Advanced Feature ......................................................................................................................................................... 29
OSD Menu Setting......................................................................................................................................................... 30
Peripheral Test.............................................................................................................................................................. 30
Lamp Hour Reset .......................................................................................................................................................... 31
Network......................................................................................................................................................................... 31
3D ................................................................................................................................................................................. 32
Factory Reset ................................................................................................................................................................ 38
Status............................................................................................................................................................................. 38
U
MAINTENANCE AND SECURITY................................................................................................................................. 39
REPLACING THE PROJECTION LAMP................................................................................................................................... 39
Resetting the Lamp........................................................................................................................................................ 41
CLEANING THE PROJECTOR................................................................................................................................................ 42
Cleaning the Lens ......................................................................................................................................................... 42
Cleaning the Case ......................................................................................................................................................... 42
USING THE KENSINGTON® LOCK ....................................................................................................................................... 43
TROUBLESHOOTING ..................................................................................................................................................... 44
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 44
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 44
LED ERROR MESSAGES .................................................................................................................................................... 45
IMAGE PROBLEMS .............................................................................................................................................................. 45
LAMP PROBLEMS ............................................................................................................................................................... 46
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 46
AUDIO PROBLEMS ............................................................................................................................................................. 47
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 47
SPECIFICATIONS............................................................................................................................................................. 48
Promethean, Company Confidential
v
SPECIFICATIONS................................................................................................................................................................. 48
PROJECTION DISTANCE VS. PROJECTION SIZE ................................................................................................................... 49
PRM-25 Projection Distance and Size Table................................................................................................................ 49
PRM-25 TIMING MODE TABLE ......................................................................................................................................... 50
PROJECTOR DIMENSIONS ................................................................................................................................................... 52
REGULATORY COMPLIANCE ..................................................................................................................................... 53
FCC WARNING .................................................................................................................................................................. 53
CANADA ............................................................................................................................................................................ 53
SAFETY CERTIFICATIONS ................................................................................................................................................... 53
EN 55022 WARNING ......................................................................................................................................................... 53
Promethean, Company Confidential
vi
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
PRM-25 DLP PROJECTOR
REMOTE CONTROL
(WITH TWO AAA BATTERIES)
POWER CORD (EU)
POWER CORD (UK)
POWER CORD (US)
RGB CABLE
RGB TO COMPONENT
ADAPTER (OPTIONAL)
CARRYING CASE
CD-ROM
(THIS USER’S MANUAL)
WARRANTY CARD
QUICK START CARD
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
Promethean, Company Confidential
1
Views of Projector Parts
PRM-25 Front-right View
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Height-adjuster button
Push to release height adjuster
2.
Height adjuster
Adjusts level of projector
3.
Lens cap
Protect lens when not in use
4.
Lens
Projection Lens
5.
IR receiver
Receive IR signal from remote control
5
6.
Focus ring
Focuses the projected image
15
14
7.
Red
Lamp is ready to be powered-on.
Flashing
Lamp not ready (Warm-up/shutting down/cooling)
(see LED Error Messages on page 45)
READY LED
POWER LED
Flashing
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
Promethean, Company Confidential
2
Rear view
ITEM
1.
LABEL
AC IN
2.
DESCRIPTION
Connect the POWER CABLE
(USB)
10
Connect the USB CABLE from a computer
3.
VGA OUT
Connect the RGB CABLE to a display
(Loop Thru only for VGA IN-1)
4.
LAN
Connect a LAN CABLE from Ethernet
5.
VGA IN – 1
Connect the RGB CABLE from a computer and
components
6.
VGA IN – 2
Connect the RGB CABLE from a computer and
components
7.
HDMI
Connect the HDMI CABLE from a HDMI device
8.
S-VIDEO IN
Connect the S-VIDEO CABLE from a video device
9.
VIDEO IN
Connect the COMPOSITE CABLE from a video device
10.
Kensington Lock
Secure to permanent object with a Kensington® Lock
system
11.
AUDIO IN (L and R)
Connect the AUDIO CABLES from a audio device
12.
RS-232
Connect RS-232 serial port cable for remote control
AUDIO IN
Connect an AUDIO CABLE from the input device
AUDIO OUT
Connect an AUDIO CABLE for audio loop through
13.
SEE PAGE:
9
43
9
Note:
If your video equipment has various input sources, it is recommended to connect in priority of
HDMI/DVI, component (thru VGA), S-Video, Composite for better picture quality.
Promethean, Company Confidential
3
Bottom view
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
2.
Ceiling support holes
Contact your dealer for information on mounting the projector on a ceiling
3.
Height adjustor
Adjuster drops down when adjuster button is pushed.
4.
Height adjustor button
Push to release adjustor.
14
14
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
Promethean, Company Confidential
4
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
Promethean, Company Confidential
5
ITEM
LABEL
DESCRIPTION
1.
IR transmitter
Transmits signals to projector
2.
Status LED
Lights when the remote control is used
3.
Laser
Press to operate the on-screen pointer
4.
Up
Up arrow when connected through USB to a PC
5.
Right
Right arrow when connected through USB to a PC
6.
Down
Down arrow when connected through USB to a PC
7.
Page Down
Page down when connected through USB to a PC
8.
Up cursor
9.
Right cursor
10.
Down cursor
11.
SEE PAGE:
Navigates and changes settings in the OSD
17
Volume +/-
Adjusts volume
16
12.
Mute
Mutes the built-in speaker
13.
Zoom+
Zoom in
14.
Zoom-
Zoom out
15.
Freeze
Freeze/unfreezes the on-screen picture
16.
Blank
Makes the screen blank
17.
Source
Detects the input device
18.
Auto
Auto adjustment for phase, tracking, size, position
19.
Menu
Opens the OSD
17
20.
Status
Opens the OSD Status menu (the menu only opens when an
input device is detected)
38
21.
Keystone top/bottom
Corrects image-trapezoid (wider top/bottom) effect
15
22.
Left cursor
Navigates and changes settings in the OSD
23.
Enter
Changes settings in the OSD
24.
Page Up
Page up when connected through USB to a PC
25.
Left
Left arrow when connected through USB to a PC
26.
Enter
Enter key when connected through USB to a PC
27.
Power
Turns the projector on or off
28.
Laser
Use as on-screen pointer. DO NOT POINT IN EYES.
Promethean, Company Confidential
15
17
10
6
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are limited in use.
Promethean, Company Confidential
7
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
2.
3.
Remove the battery compartment cover
by sliding the cover in the direction of
the arrow.
Insert the battery with the positive side
facing up.
Replace the cover.
Caution:
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
Promethean, Company Confidential
8
Connecting Input Devices
A PC or notebook computer and video devices can be connected to the projector at the same time. Video
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras.
Check the user manual of the connecting device to confirm it has the appropriate output connector.
ITEM
LABEL
(USB)
DESCRIPTION
Connect the USB CABLE from a computer
VGA OUT
Connect the RGB CABLE to a display (Loop Thru only for VGA IN-1)
LAN
Connect a LAN CABLE from Ethernet
VGA IN – 1
Connect the RGB CABLE from a computer and components
VGA IN – 2
Connect the RGB CABLE from a computer and components
AUDIO IN
Connect an AUDIO CABLE from the input device
AUDIO OUT
Connect an AUDIO CABLE for audio loop through
HDMI
Connect the HDMI CABLE from a HDMI device
S-VIDEO IN
Connect the S-VIDEO CABLE from a video device
VIDEO IN
Connect the COMPOSITE CABLE from a video device
AUDIO IN (L and R)
Connect the AUDIO CABLES from a audio device
RS-232C
Connect the RS-232 serial cable for remote control
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
Promethean, Company Confidential
9
Starting and Shutting down the Projector
1.
2.
3.
Connect the power cord to the projector.
Connect the other end to a wall outlet.
The
POWER and READY LEDs
on the projector light.
Turn on the connected devices.
Ensure the READY LED displays a
solid red and not a flashing red. Then
press the
POWER button to turn on
the projector.
The projector splash screen displays and
connected devices are detected.
See Setting an Access Password
(Security Lock) on page 12 if security
lock is enabled.
4.
If more than one input device is connected, press the SOURCE button and
use ▲▼ to scroll among devices.
(Component is supported through the
RGB to COMPONENT ADAPTER.)
Promethean, Company Confidential
•
VGA 1/VGA 2: Analog RGB
Component: DVD input YCbCr / YPbPr, or
HDTV input YPbPr via HD15 connector
•
Composite Video: Traditional composite video
•
S-Video: Super video (Y/C separated)
•
HDMI: HDMI, DVI
10
5.
When the “Power Off? /Press Power
again” message appears, press the
POWER button. The projector turns
off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector has
cooled down.
Promethean, Company Confidential
11
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating
the OSD on page 17 and Setting the OSD Language on page 18 for help on using OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
1.
2.
3.
4.
Press the MENU button to open the OSD
menu.
Press the cursor ◄► button to move to
the Installation I menu.
Press the cursor ▲▼ button to select
Security Lock.
Press the cursor ◄► button to enable or
disable security lock function.
A password dialog box automatically
appears.
Promethean, Company Confidential
12
5.
You can use the cursor buttons ▲▼◄►
on IR remote control for password entry.
You can use any combination including
the same arrow five times, but not less
than five.
Press the cursor buttons in any order to set
the password. Push the MENU button to
exit the dialog box.
6.
The password confirm menu appears when
user presses the power-on key in case the
Security Lock is enabled.
Enter the password in the order you set it
at step 5. In case you forget the password,
please contact the service center.
Service center will validate the owner and
help reset the password.
Promethean, Company Confidential
13
Adjusting the Projector Level
Take note of the following when setting up the projector:
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Ensure the cables are in a safe location. You could trip over them.
1.
To raise the level of the projector, lift the projector [A] and press the height-adjuster
button [B].
The height adjuster drops down [C].
2.
3.
To lower the level of the projector, press the height-adjuster button and push down
on the top of the projector.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the
desired angle has been achieved.
Promethean, Company Confidential
14
Adjusting the Focus and Keystone
1.
2.
3.
Use the Image-focus
control (on the projector
only) to sharpen the projected image A .
Use the KEYSTONE
buttons the remote control
to correct image-trapezoid
(wider top or bottom)
effect.
The keystone control
appears on the display.
Promethean, Company Confidential
15
Adjusting the Volume
1.
Press the Volume +/buttons on the remote
control.
The volume control
appears on the display.
Note: This volume control
is for connected external audio devices
as there are no
speakers within the
projector.
2.
Press the MUTE button to
turn off the volume.
Promethean, Company Confidential
16
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector.
1. To enter the OSD, press the
MENU button.
2. There are five menus. Press
the cursor ◄► button to
move through the menus.
3. Press the cursor ▲▼ button
to move up and down in a
menu.
4. Press ◄► to change values
for settings.
5. Press MENU to close the
OSD or leave a submenu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC.
Items that are not available cannot be accessed and are grayed out.
Promethean, Company Confidential
17
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I.
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ◄► button until the language you want is highlighted.
4. Press the MENU button twice to close the OSD.
Promethean, Company Confidential
18
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
English, French, German, Spanish, Portuguese, Simplified Chinese, Traditional Chinese,
Italian, Norwegian, Swedish, Dutch, Russian, Danish, Finnish, Japanese, Korean,
Brazilian Portuguese, Kazakh, Vietnamese, Arabic, Turkish
Promethean, Company Confidential
19
OSD Sub-Menu Overview
Promethean, Company Confidential
20
Image Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image
Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change
values for settings.
ITEM
DESCRIPTION
Display Mode
Press the cursor ◄► button to set the Display Mode.
Brilliant Color
Press the cursor ◄► button to adjust the Brilliant Color value.
Brightness
Press the cursor ◄► button to adjust the display brightness.
Contrast
Press the cursor ◄► button to adjust the display contrast.
Sharpness
Press the cursor ◄► button to adjust the display sharpness level.
Gamma
Press the cursor ◄► button to adjust the gamma correction of the display.
Advanced
Press
(Enter) / ► to enter the Advanced menu. See Advanced Feature on page 22.
Reset
Press
(Enter) / ► to reset all settings to default values.
Promethean, Company Confidential
21
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲
to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the
Advanced menu.
ITEM
DESCRIPTION
Color Space
Press the cursor ◄► button to adjust the color space.
(Range: Auto – RGB – YPbPr – YCbCr)
Color Temperature
Press the cursor ◄► button to adjust the color temperature.
(Range: Cold – Normal – Warm)
Color Manager
Press
(Enter) / ► to enter the color manager menu. (Range: Red-Green-Blue-CyanMagenta-Yellow-White). See page 23 for more information on Color Manager.
Promethean, Company Confidential
22
Color Manager
Press
(Enter) / ► to enter the Color Manager sub menu.
ITEM
DESCRIPTION
Red
Select to enter the Red Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Green
Select to enter the Green Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Blue
Select to enter the Blue Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Cyan
Select to enter the Cyan Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Magenta
Select to enter the Magenta Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Yellow
Select to enter the Yellow Color Manager.
Press the◄► buttons to adjust the Hue, Saturation, and Gain.
White
Select to enter the White Color Manager.
Press the ◄► buttons to adjust the Red, Green, and Blue.
Promethean, Company Confidential
23
Computer Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Computer menu. Press the cursor ▲▼ button to move up and down in the computer menu. Press ◄► to
change values for settings.
ITEM
DESCRIPTION
Horizontal Position
Press the cursor ◄► button to adjust the display position to left or right.
Vertical Position
Press the cursor ◄► button to adjust the display position to up or down.
Frequency
Press the cursor ◄► button to adjust the A/D sampling clock.
Tracking
Press the cursor ◄► button to adjust the A/D sampling dot.
Auto Image
Press
(Enter) / ► to automatically adjustment for phase, tracking, size and position.
Promethean, Company Confidential
24
Video/Audio Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu.
Press ◄► to change values for settings.
ITEM
DESCRIPTION
Video AGC
Press the ◄► buttons to enable or disable the Automatic Gain Control for video source.
Video Saturation
Press the ◄► buttons to adjust the video saturation.
Video Tint
Press the ◄► buttons to adjust the video tint/hue.
Film Mode
Press the ◄► buttons to select a different film mode.
Video Overscan
Press the ◄► buttons to enable or disable video over scan.
Audio
Press
(Enter) / ► to enter the Audio menu. See Audio on page 26.
Reset
Press
(Enter) / ► to reset all settings to default values.
Note:
Video jagging may occur when playing interlace video. To overcome this issue, open the
Video / Audio menu and adjust the Film Mode feature.
Promethean, Company Confidential
25
Audio
Press
(Enter) / ► to enter the Audio sub menu.
ITEM
DESCRIPTION
Volume
Press the ◄► buttons to adjust the audio volume.
(Range: 0 ~ 8)
Mute
Press the ◄► buttons to turn on or off the speaker.
Audio Input
Press the cursor ◄► button to select audio input.
(Range: Mini ~ RCA)
Promethean, Company Confidential
26
Installation I Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press
◄► to change values for settings.
ITEM
DESCRIPTION
Language
Press the cursor ◄► button to select a different localization Menu.
Blank Screen
Press the cursor ◄► button to select different color to blank the screen.
Projection
Press the cursor ◄► button to choose from four projection methods:
Security Lock
Press the cursor ◄► button to enable or disable security lock function.
Aspect Ratio
Press the cursor ◄► button to adjust the video aspect ratio.
Keystone
Press the cursor ◄► button to adjust the display keystone.
Digital Zoom
Press the cursor ◄► button to adjust the Digital Zoom menu.
Reset
Press
(Enter) / ► to reset all settings to default values
(except Language and Security Lock).
Promethean, Company Confidential
27
Installation II Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu.
ITEM
DESCRIPTION
Auto Source
Press the cursor ◄► button to enable or disable automatic source detection.
Auto Power Off
(min.)
Press the cursor ◄► button to enable or disable automatic shutdown of lamp when no signal.
Auto Power On
Press the cursor ◄► button to enable or disable automatic power On when AC power is supplied.
Fan Speed
Press the cursor ◄► button to toggle between Normal and High fan speeds.
Note: We recommend selecting high speed in high temperatures, high humidity, or high
altitude areas.
Lamp Mode
Press the cursor ◄► button to select the lamp mode for higher brightness or lower brightness
to save lamp life.
Advanced
Press
(Enter) / ► to enter the Advanced menu. See Advanced Feature on page 29.
Factory Reset
Press
(Enter) / ► to reset all items to factory preset values.
Status
Press
(Enter) / ► to enter the Status menu. See page 38 for more information on Status.
Promethean, Company Confidential
28
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu.
Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and
down in the Advanced menu. Press ◄► to change values for setting.
ITEM
DESCRIPTION
OSD Menu Setting
Press
(Enter) / ► to enter the OSD setting menu. See page 30 for more information on
OSD Menu Setting.
Peripheral Test
Press
(Enter) / ► to enter the Peripheral Test menu. See page 30 for more information on
Peripheral Test.
Lamp Hour Reset
After replacing the lamp, this item should be reset. See page 31 for more information on Lamp
Hour Reset.
Low Power Mode
Press ◄► to turn Low Power Mode on or off.
RS232
Press ◄► to select RS232 (remote) or Network (LAN) mode depending on projector connection method.
Network
Press
(Enter) / ► to enter the Network menu. See page 31 for more information on Network settings.
3D
Press
(Enter) / ► to enter the 3D menu. See page 32 for more information on 3D settings.
Note:
To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD
device under the 3D Disc Menu.
Promethean, Company Confidential
29
OSD Menu Setting
ITEM
DESCRIPTION
Menu Position
Press ◄► button to select different OSD location.
Translucent Menu
Press ◄► button to select OSD background translucent level.
Menu Display
Press ◄► button to select OSD timeout delay.
Peripheral Test
ITEM
DESCRIPTION
Remote Control Test
Press
(Enter) / ► to test the IR remote controller for diagnostic.
USB Test
Press
(Enter) / ► to test the USB connection with connected PC.
Color Test
Press
(Enter) / ► to select different colors on screen.
Promethean, Company Confidential
30
Lamp Hour Reset
Please refer to Resetting the Lamp on page 41 to reset the lamp hour counter.
Network
ITEM
Network State
DESCRIPTION
Displays the network connection status.
Press ◄► to turn DHCP On or Off.
DHCP
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS
fields.
IP Address
Enter a valid IP address if DHCP is turned off.
Subnet Mask
Enter a valid Subnet Mask if DHCP is turned off.
Gateway
Enter a valid Gateway address if DHCP is turned off.
DNS
Enter a valid DNS name if DHCP is turned off.
Apply
Press
(Enter) / ► to confirm settings.
Promethean, Company Confidential
31
3D
ITEM
DESCRIPTION
3D 60Hz Sync
Press ◄► to turn 3D 60Hz On or Off.
3D 120Hz Sync
Press ◄► to turn 3D 120Hz On or Off.
3D Sync Invert
Press ◄► to turn 3D Sync Invert On or Off.
Note:
The PRM-25 is 3D ready, please contact Promethean for more details.
Promethean, Company Confidential
32
For simplicity and ease of operation, the projector provides diverse networking and remote management features.
The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off,
Brightness and Contrast settings. Also, projector status information, such as: Video-Source, SoundMute, etc.
LAN_RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).
2. On the PC (Laptop), select Start ´ Control Panel ´ Network Connections.
Promethean, Company Confidential
33
3. Right-click on Local Area Connection, and select Properties.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP).
5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click
OK.
Promethean, Company Confidential
34
7. Press the Menu button on the projector.
8.
Select Installation II ´ Advanced ´ Network.
9.
After getting into Network, input the following:
` DHCP: Off
` IP Address: 192.168.10.10
` Subnet Mask: 255.255.255.0
` Gateway: 0.0.0.0
` DNS Server: 0.0.0.0
10. Press
(Enter) / ► to confirm settings.
11. Open a web browser (for example, Microsoft Internet Explorer).
12. In the Address bar, input the IP address: 192.168.10.10.
13. Press
(Enter) / ►.
The projector is setup for remote management. The LAN/RJ45 function displays as follows.
Promethean, Company Confidential
35
14. Click Control Panel to display projector settings.
Preparing Email Alerts
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for example, Microsoft Internet Explorer v6.01/v7.0).
2. From the Homepage of LAN/RJ45, click Alert Setting.
3. By default, these input boxes in Alert Setting are blank.
Promethean, Company Confidential
36
4. The To field is the recipients email address (for example, projector administrator). This is a
required field.
The Cc field sends a carbon copy of the alert to the specified email address. This is an optional field (for example, assistant of projector administrator). This Cc field is optional input.
The “Subject” field is the subtitle for email. This is a required field.
The From field is the sender’s email address (for example, projector administrator). This is a
required field.
The SMTP field is the mail server for sending out email (SMTP protocol).
This is a required field.
Select the alerting conditions by checking the desired boxes.
See the example below:
5. When the above necessary input fields correct, then press Email Alert Test button.
In a few seconds, the specified mailbox receives a test email as shown below:
Note:
Fill in all fields as specified. Select the desired alert condition and click Submit to conduct
an Email Alert Test. A successful test alerts the designated email accounts.
To create an email alert, you must select alert conditions and enter a correct email address.
Group and Projector Name identify the alerting projector and are located at the top of the
LAN RJ45 web page as shown below:
Promethean, Company Confidential
37
Factory Reset
Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory
(Enter) / ► to reset all the menu items to the factory default values
Reset sub menu and press
(expect Language and Security Lock).
Status
Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the
(Enter) / ► to enter the Status sub menu.
Installation II sub menu and press
ITEM
DESCRIPTION
Active Source
Display the activated source.
Video Information
Displays resolution/video information for RGB source and color standard for Video source.
Lamp Hours
Lamp hour used information is displayed. Normal and Bright counters are separated.
Promethean, Company Confidential
38
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.
1.
2.
Remove the single screw on
the lamp compartment cover.
Remove the lamp compartment cover.
Promethean, Company Confidential
39
3.
4.
Remove the three screws from
the lamp module.
Lift the module handle up.
5.
Pull firmly on the module
handle to remove the lamp
module.
6.
Reverse steps 1 to 5 to install
the new lamp module.
While installing, align the
lamp module with the
connector and ensure it is level
to avoid damage.
Note: The lamp module must
sit securely in place and the
lamp connector must be connected properly before
tightening the screws.
Promethean, Company Confidential
40
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.
7.
8.
9.
Press the MENU button to open the
OSD menu.
Press the cursor ◄► button to move
to the Installation II menu. Press the
cursor button to move down to
Advanced.
Press the cursor ▼▲ button to move
down to Lamp Hour Reset.
Press the cursor ► or Enter button.
A message screen appears.
10. Press ▼▲◄► buttons to reset the
lamp hour.
11. Press the MENU button to get back
to Installation II.
Promethean, Company Confidential
41
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the
lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then
wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
Promethean, Company Confidential
42
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,
http://www.Kensington.com.
Promethean, Company Confidential
43
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
•
Use some other electrical device to confirm that the electrical outlet is working.
•
Ensure the projector is turned on.
•
Ensure all connections are securely attached.
•
Ensure the attached device is turned on.
•
Ensure a connected PC is not in suspending mode.
•
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing a Fn-key combination on the notebook).
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
Promethean, Company Confidential
44
LED Error Messages
ERROR CODE MESSAGES
POWER LED BLINK
READY LED BLINK
Over temperature
3
0FF
G794 fail
4
4
T1 fail
4
5
Lamp error
5
OFF
Ballast Over Temperature
5
1
Ballast shot circuit in output detected
5
2
End of lamp lift detected
5
3
Ballast lamp did not ignite
5
4
Lamp extinguished during normal operation
5
5
Lamp extinguished during run-up phase
5
6
Lamp Memory write error
5
7
Lamp Memory write buffer overflow
5
8
Lamp UART buffer overflow
5
9
Lamp current calculation error
5
10
Lamp Corrupted software configuration
5
11
Lamp voltage too low
5
12
Lamp FLASH memory CRC error
5
13
Lamp EEPROM memory CRC error
5
14
Lamp EEPROM configuration does not match FLASH kernel
5
15
Buner Fan
6
1
Lamp Fan
6
2
Power Fan
6
3
DMD Fan
6
4
Lamp door open
7
OFF
DMD error
8
OFF
Color wheel error
9
OFF
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact
your service center.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
Promethean, Company Confidential
45
3. Ensure the projector-to-screen distance is within the 4-meter (13-feet) specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Installation I menu of the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the READY LED
is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Promethean, Company Confidential
46
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Note:
This volume control is for connected external audio devices as there are no speakers within the
projector.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.
Promethean, Company Confidential
47
SPECIFICATIONS
Specifications
Model
PRM-25
TI DMD 0.65" WXGA
Display type
WXGA 1280 x 800 Native
Resolution
3.6 kg (7.9 lbs)
Weight
0.5 meters ~ 5 meters
Projection distance
44.4” ~ 444” (diagonal)
Projection screen size
Manual Focus
Projection lens
Throw ratio
(D/W – D/Dia)
Vertical keystone
correction
0.523 – 0.444
+/- 15 degrees
Projection methods
Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility
VGA, SVGA, XGA, SXGA, UXGA, Mac
SDTV/EDTV/ HDTV
480i, 576i, 480p, 576p, 720p, 1080i, 1080p
NTSC/NTSC 4.43, PAL (B/G/H/I/M/N/60), SECAM
Video compatibility
H-Sync
15, 30 – 80 kHz
V-Sync
43 – 87 Hz
Safety certification
FCC-B, UL, CB, CE, CCC, KC, PSB, TUV-GS, GOST, SASO, KUCAS, NOM
Operation temperature
Dimensions
AC Input
5° ~ 35°C
335 mm (W) x 102 mm (H) x 256 mm (D)
AC Universal 100 ~ 240, Typical @ 110VAC (100~240)/+-10%
Power consumption
290W
Stand By
<1 watt
Lamp
230W
VGA x 2
S-Video x 1
Input Terminals
Composite Video x 1
HDMI 1.3 x 1
RCA stereo x 1
Mini-jack stereo x 1
Output Terminals
VGA x 1 (Loop Thru only for VGA IN-1)
Mini-jack stereo x 1
RS-232C
Control Terminals
RJ45
USB (type B)
Security
Promethean, Company Confidential
Kensington lock
48
Projection Distance vs. Projection Size
PRM-25 Projection Distance and Size Table
PRM-25
Distance (m)
TELE
0.72
0.88
0.98
1.07
64
78
87
95
Keystone Correction Angle (degree)
38.42
38.42
38.42
38.42
Image Height (mm)
861.6
1050
1171.2
1278.9
Image Width (mm)
1378.5
1680.1
1873.9
2046.2
A (mm)
140.6
171.4
191.1
208.7
Diagonal (inches)
Promethean, Company Confidential
49
PRM-25 Timing Mode Table
The projector can display several resolutions. The following table outlines the resolutions that can be
displayed by the projector.
SIGNAL
RESOLUTION
H-SYNC
(KHZ)
V-SYNC COMPOSITE
RGB
COMPONENT
(HZ)
/ S-VIDEO
(ANALOG)
DVI/
HDMI
(DIGITAL)
NTSC
—
15.734
60.0
O
—
-
-
PAL/SECAM
—
15.625
50.0
O
—
-
-
720 x 400
37.9
85.0
—
—
O
O
640 x 480
31.5
60.0
—
—
O
O
640 x 480
37.9
72.8
—
—
O
O
640 x 480
37.5
75.0
—
—
O
O
640 x 480
43.3
85.0
—
—
O
O
800 x 600
35.2
56.3
—
—
O
O
800 x 600
37.9
60.3
—
—
O
O
800 x 600
46.9
75.0
—
—
O
O
800 x 600
48.1
72.2
—
—
O
O
800 x 600
53.7
85.1
—
—
O
O
1024 x 768
48.4
60.0
—
—
O
O
1024 x 768
56.5
70.1
—
—
O
O
1024 x 768
60.0
75.0
—
—
O
O
1024 x 768
68.7
85.0
—
—
O
O
1280 x 800
49.7
59.8
—
—
O
O
1280 x 800
62.8
74.9
—
—
O
O
1280 x 800
71.6
84.8
—
—
O
O
1280 x 1024
64.0
60.0
—
—
O
O
1280 x 1024
80.0
75.0
—
—
O
O
1280 x 1024
91.1
85.0
—
—
O
O
1400 x 1050
65.3
60.0
—
—
O
O
1440 x 900
55.9
60.0
—
—
O
O
1600 x1200
75.0
60
—
—
O
O
640 x 480
35.0
66.7
—
—
O
O
832 x 624
49.7
74.5
—
—
O
O
1024 x 768
60.2
74.9
—
—
O
O
1152 x 870
68.7
75.1
—
—
O
O
480i
15.734
60.0
—
O
—
O
576i
15.625
50.0
—
O
—
O
576p
31.3
50.0
—
O
—
O
480p
31.5
60.0
—
O
—
O
VESA
Apple
Macintosh
SDTV
EDTV
Promethean, Company Confidential
50
SIGNAL
HDTV
RESOLUTION
H-SYNC
(KHZ)
V-SYNC COMPOSITE
RGB
COMPONENT
(HZ)
/ S-VIDEO
(ANALOG)
DVI/
HDMI
(DIGITAL)
720p
37.5
50.0
—
O
—
O
720p
45.0
60.0
—
O
—
O
1080i
33.8
60.0
—
O
—
O
1080i
28.1
50.0
—
O
—
O
1080p
67.5
60.0
—
O
—
O
1080p
56.3
50.0
—
O
—
O
O: Frequency supported
—: Frequency not supported
The resolution of the panel for the PRM-25 is 1280 x 800. Resolution other than native resolution may
display with uneven size of text or lines.
Promethean, Company Confidential
51
Projector Dimensions
Promethean, Company Confidential
52
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, UL, CB, CE, CCC, KC, TUV-GS, GOST, SASO, KUCAS, NOM, and PSB
EN 55022 Warning
This is a Class B product. In a domestic environment, it may cause radio interference, in which case
the user may be required to take adequate measures. The typical use is in a conference room, meeting room, or auditorium.
Promethean, Company Confidential
53
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising