MULTIQUIP | MVC-HW | Specifications | MULTIQUIP MVC-HW Specifications

MULTIQUIP MVC-HW Specifications
OPERATION & PARTS MANUAL
SERIES
MODEL MVC-88GH/GHW
ONE-WAY PLATE COMPACTOR
(HONDA GASOLINE ENGINE)
Revision #4 (10/15/04)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALL TIMES.
l
PAGE 2 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Email: mq@multiquip.com
Internet: www.multiquip.com
PARTS DEPARTMENT
800-427-1244
310-537-3700
MAYCO PARTS
800-306-2926
310-537-3700
SERVICE DEPARTMENT
800-421-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
800-421-1244
FAX: 310-537-3927
FAX: 800-672-7877
FAX: 310-637-3284
FAX: 800-672-7877
FAX: 310-637-3284
FAX: 310-537-4259
FAX: 310-631-5032
FAX: 310-537-1173
© COPYRIGHT 2004, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without
written permission. All other trademarks are the property of thier respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should
remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are
based on the Mikasa MVC-88GH/GHW Plate Compactor. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change
specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 3
TABLE OF CONTENTS
Multiquip —MVC88GH/GHW
Plate Compactor
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ...................................... 8-9
Operation and Safety Decals .................................. 10
Specifications (Compactor/Engine) ........................ 11
General Information ................................................ 12
Components (Plate Compactor) ............................. 13
Components (Engine) ............................................. 14
Inspection ........................................................... 15-16
Initial Start-Up .................................................... 17-18
Operation ................................................................ 18
Maintenance ...................................................... 20-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine) ................................... 23-24
Troubleshooting (Plate Compactor) ........................ 24
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Honda GX160K1QMX2 Engine
Cylinder Head Assembly ....................................38-39
Cylinder Barrel (Recoil) Assembly .....................40-41
Crankcase Cover Assembly ...............................42-43
Crankshaft Assembly .........................................44-45
Piston/Rings Assembly.......................................46-47
Camshaft Assembly ...........................................48-49
Recoil Starter .....................................................50-51
Fan Cover Assembly ..........................................52-53
Carburetor Assembly .........................................54-55
Air Cleaner Assembly.........................................56-57
Muffler Assembly ...............................................58-59
Fuel Tank Assembly ...........................................60-61
Cooling Fan & Flywheel Assembly .....................62-63
Ignition Coil Assembly ........................................64-65
Control Assembly ...............................................66-67
Gasket Assembly ...............................................68-69
Labels ................................................................70-71
Terms and Conditions Of Sale — Parts .................. 72
Component Drawings
Nameplate and Decals....................................... 28-29
Body Assembly .................................................. 30-31
Vibrator Assembly .............................................. 32-33
Sprinkler Assembly (Option) .............................. 34-35
Transport Wheel Assembly (Option) .................. 36-37
l
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
❒
❒
❒
❒
❒
❒
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
Note: Unless otherwise indicated by customer, all
✓ FedEx or UPS Ground
orders are treated as “Standard Orders”, and will
✓ FedEx or UPS Second Day or Third Day
ship within 24 hours. We will make every effort to
✓ FedEx or UPS Next Day
ship “Air Shipments” the same day that the order is
✓ Federal Express Priority One
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓ DHL
✓ Truck
Here’s how to get help...
Please have the model and serial number
on hand when calling.
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
800-421-1244
FAX: 310-537-3927
Carson, CA 90746
Email: mq@multiquip.com
Internet: www.multiquip.com
PARTS DEPARTMENT
800-427-1244
FAX: 800-672-7877
310-537-3700
FAX: 310-637-3284
MAYCO PARTS
800-306-2926
FAX: 800-672-7877
310-537-3700
FAX: 310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX: 310-537-4259
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
FAX: 310-537-1173
310-537-3700, EXT. 279
MULTIQUIP INC.
18910 WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700 • 800-421-1244
FAX: 310-537-3927
E-MAIL: mq@multiquip.com
WWW: multiquip.com
Place Your Parts Order Via Web or Fax
For Even More Savings!
Extra Discounts!
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Ordered
via
Fax
Standard
orders
3%
Web
5%
Stock orders
($750 list and above)
10%
10%
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other
carrier.
NOTE: DISCOUNTS ARE SUBJECT TO CHANGE
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 5
MVC-88H PLATE COMPACTOR — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Potential hazards associated with the operation of a MVC88 Plate Compactor will be referenced with Hazard Symbols
which appear throughout this manual, and will be referenced
Lethal Exhaust Gases
in conjunction with Safety Message Alert Symbols.
WARNING
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MQ Mikasa MVC-88
Plate Compactor. Refer to the engine
manufacturers instructions for data
relative to its safe operation.
NOTE
Before using this plate compactor, ensure that the
operating individual has read and understands all
instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
WARNING
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTI
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Explosive Fuel Hazards
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
WARNING
l
Lethal Exhaust Gas Hazards
Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
WARNING
Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 6 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88H PLATE COMPACTOR — SAFETY MESSAGE ALERT SYMBOLS
CAUTION
Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
CAUTION
CAUTION
Equipment Damage
Hazards
Other important messages are provided throughout this
manual to help prevent damage to your portable generator,
other property, or the surrounding environment.
Accidental Starting Hazards
ALWAYS place the engine ON/OFF switch
in the OFF position, when the plate
compactor is not in use.
CAUTION
Eye and Hearing Hazards
ALWAYS wear approved eye and hearing
protection.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 7
MVC-88H PLATE COMPACTOR — RULES FOR SAFE OPERATION
WARNING - Read This Manual
Failure to follow instructions in this manual may lead to
Serious Injury or even Death. This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used
when operating the Mikasa MVC-88H Plate Compactor:
Safety:
■ DO NOT operate or service this
equipment before reading this entire
manual.
■ This equipment should not be operated
by persons under 18 years of age.
■ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■ NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to
cool before servicing engine or
generator.
■ High Temperatures – Allow the engine
to cool before adding fuel or performing
service and maintenance functions.
Contact with hot! components can cause serious burns.
■ The engine of this plate compactor requires an adequate
free flow of cooling air. NEVER operate the plate
compactor in any enclosed or narrow area where free
flow of the air is restricted. If the air flow is restricted it
will cause serious damage to
the plate compactor or engine
and may cause injury to people
and property. Remember the
compactor's engine gives off
DEADLY gases.
■ ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
■ NEVER operate the plate compactor under the influence
or drugs or alcohol.
■ NEVER disconnect any "emergency or safety devices".
l for operator safety.
These devices are intended
Disconnection of these devices can cause severe injury,
bodily harm or even death! Disconnection of any of these
devices will void all warranties.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■ NEVER operate the plate compactor in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■ Topping-off to filler port is dangerous, as it tends to spill
fuel.
■ ALWAYS store the plate compactor in a clean, dry
location out of the reach of children.
■ NEVER run engine without air cleaner. Severe engine
damage may occur.
■ NEVER leave the plate compactor unattended, turn off
engine.
■ CAUTION must always be observed while servicing this
plate compactor. Rotating parts can cause injury if
contacted.
■ ALWAYS check all the bolts on the plate compactor for
tightness.
PAGE 8 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88H PLATE COMPACTOR — RULES FOR SAFE OPERATION
Loading and Unloading (Crane):
■ Before lifting, make sure that machine parts (hook and
vibration insulator) are not damaged and screws are not
loosened or lost.
■ ALWAYS make sure crane or lifting device has been
properly secured to the hook of guard frame on compactor.
■ NEVER lift the machine while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient
strength.
■ Use one point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath
the machine while lifting.
■ Try not to lift machine to unnecessary heights.
Maintenance Safety:
■ NEVER lubricate components or attempt service on a
running machine.
■ ALWAYS allow the machine a proper amount of time to
cool before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always
replace broken parts.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
■ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
Transporting
■ ALWAYS shutdown engine before transporting.
■ Tighten fuel tank cap securely and close fuel cock to Emergencies:
prevent fuel from spilling.
■ ALWAYS know the location of the
■ Drain fuel when transporting compactor over long
nearest fire extinguisher.
distances or bad roads.
■ ALWAYS know the location of the
■ ALWAYS tie down the compactor during transportation
nearest first aid kit.
by securing the compactor's guard frame with rope.
■ In emergencies always know the location
of the nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance , doctor and fire department . This
information will be invaluable in the case of an
emergency.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 9
MVC-88GH/HWOPERATION AND SAFETY DECALS
Machine Safety Decals
The MVC-88GH/GHW Plate Compactor is equipped with a number of safety decals. These decals are provided for operator safety
and maintenance information. The illustration below shows these decals as they appear on the machine. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
l
PAGE 10 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/HWSPECIFICATIONS
TABLE 1. Specifications (Compactor)
Models
MVC-88GH/MVC-88GHW
Centrifugal Force
3,450 lbs. (1,564.9 kg)
Number of Vibrations
5,800 vibrations/min
Traveling Speed
72 ft./min (22 meters/min)
Plate Size (LxW)
19.7 x 20.7 in.
.500 x .525 mm
Operating Weight (GW)
Operating Weight (GHW)
183 lbs. (83.0 kg.)
212 lbs. ( 96.2 kg.)
Fuel Tank Capacity
3.8 qt. (3.6 liters)
Water Tank Capacity
GHW Model Only
13.7 qt. (13.0 liters)
Max. Area Of Compaction
7092 sq. ft./hr.
Table 2. Specifications (Engine)
Model
Type
HONDA GX160K1QMX2
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Bore X Stroke
2.7 in. x 1.8 in.
(68 mm x 45 mm)
Displacement
163 cc (9.9 cu-in)
Max Output
5.0 H.P./3600 R.P.M.
Engine
Fuel Tank Capacity
Fu e l
Lube Oil Capacity
Speed Control Method
Star ting Method
Dimension (L x W x H)
Dry Net Weight
Approx. 0.95 U.S. gallons
(3.6 liters)
Unleaded Automobile
Gasoline
.60 liters (0.63 qts)
Centrifugal Fly-weight
Type
Recoil Star t
12.0 x 14.4 x 13.2 in.
(304 x 362 x 335 mm
33.1 lbs (15 Kg.)
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 11
MVC-88GH/GHW GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC-88GH/GHW is a walk behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor's vibrating plate has a frequency range between
5800 vpm (vibrations per minute). The forward and reverse travel
speed of the compactor is approximately 23 meters/minute (75
ft./minute).
Vibratory Plates
The vibratory plates of the MVC-88GH/GHWproduce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
The resulting vibrations cause forward motion. The engine and
handle are vibration isolated from the vibrating plate.
Engine
The Mikasa MVC-88GH/GHW Plate Compactor is equipped with
an Honda air cooled, 4-cycle gasoline engine. The engine drives
an eccentric weight at a high speed to develop a compaction
force. In addition this engine is equipped with an Oil Alert
system that will automatically stop the engine before the
engine falls below safe engine oil operating limits. Always
be sure to check the engine oil level prior to starting the
engine.
Controls
Before starting the MVC-88GH/GHW Plate Compactor identify
and understand the function of the controls and components as
indicated in Figure 1.
l
PAGE 12 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/HWCOMPONENTS (PLATE COMPACTOR)
Figure 1. Plate Compactor Controls
Figures 1 shows the location of the basic controls and
components of the MVC-88 Plate Compactor. The function of
each control is described below:
6.
Belt Cover – Remove this cover to gain acess to the Vbelts. NEVER run the compactor without the V-belt cover. If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
1.
Water Tank Cap – Remove this cap to add water to the
water tank.
2.
Fuel Tank Cap – Remove this cap to add fuel.
7.
3.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
Vibrating Plate – A flat, open plate made of durable cast
iron construction used in the compacting of soil.
8.
Vibration Case – Encloses the eccentric, gears and
counter weights.
4.
Handle Bar – When operating the compactor use this
handle bar to manuever the compactor.
9.
Water Tube (Sprinkler) – Supplies water to the soil via a
splash plate.
5.
Gasoline Engine – This plate compactor uses a HONDA
GX160K1QMX2 engine. Refer to the HONDA owners
manual for engine information and related topics.
10. Water Shut-Off Valve – Turn this valve downward to let
water flow from the water tank to the water tube.
11. Water Tank – Holds 13.7 quarts of water, removable no
tools required.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 13
MVC-88GH/GHW ENGINE COMPONENTS
Figure 2. Engine Controls & Components
INITIAL SERVICING
5.
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
1.
7.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
DANGER
Explosive
Fuel Hazard
NOTE
Adding fuel to the tank should be done only when
l an opportunity
the engine is stopped and has had
to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry.
2.
Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
3.
Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4.
Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
WARNING
Operating the engine without an air
filter, with a damaged air filter, or a filter
in need of replacement will allow dirt
to enter the engine, causing rapid
engine wear.
Burn Hazard
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
8.
Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9.
Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
PAGE 14 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— INSPECTION
CAUTION
NEVER operate the pump in a confined area
or enclosed area structure that does not
provide ample free flow of air.
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 4), fill to the edge of the oil filler
hole with the recommended oil type (Table 3). Maximum oil
capacity is 0.63 quarts (0.60 liters)
ALWAYS wear approved eye and hearing
protection before operating the compactor.
Before Starting
1.
Read safety instructions at the
beginning of manual.
2.
Clean the compactor, removing
dirt and dust, particularly the
engine cooling air inlet, carburetor
and air cleaner.
3.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
5.
Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 3) and wipe clean.
Figure 4. Engine Oil Dipstick (Oil Level)
Table 3. Oil Type
Season
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
DANGER
Explosive
Fuel Hazard
Adding fuel to the fuel tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until the
fuel residue has been completely wiped up, and the area
surrounding the engine is dry. DO NOT attempt to refuel the
compactor if the engine is hot! or running.
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel immediately!
Figure 3. Engine Oil Dipstick (Removal)
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 15
MVC-88GH/GHW— INSPECTION
2. The V-belt tension is proper if the V-belt bends 10 to 15 mm
(Figure 7) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
CAUTI
CAUTION
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur of your hand (Figure 5) gets caught
between the V-belt and the clutch. Always use safety gloves.
CLUTCH
PULLEY
Figure 7. V-Belt Tension
VIBRATOR
PULLEY
Figure 5. V-Belt Hazard
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 6.
3. A loose V-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
4. If the V-belt becomes worn or loose, replace it by using Vbelt part number RPF-3320 or A-32.
Vibrator Oil Check
1. Place the MVC-88GH/GHW plate compactor horizontally on
a flat surface. Make sure the compactor is level when checking the oil in the vibrator assembly.
2. Check vibrator oil level by removing the plug (vibrator oil gauge)
as shown in Figure 8. The oil level should be up to the oil plug.
The vibrator holds 140 cc (approximately 1 pint).IMPORTANT,
if oil is required, replace using only SAE 10W-30 motor oil.
l
Figure 8. Vibrator Oil Plug
Figure 6. V-Belt Cover Removal
PAGE 16 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— INITIAL START-UP
CAUTI
CAUTION
The CLOSED position of the
choke lever enriches the fuel
mixture for starting a COLD
engine. The OPEN position
provides the correct fuel
mixture for normal operation
after starting, and for restarting
a warm engine.
NOTE
D
DO NOT attempt to run the compactor until
the Safety and Initial Start-upsectionshave
been read and understood.
1. Place the fuel valve lever (Figure 9) in the "ON" position.
4. Place the throttle lever (Figure 12) halfway between fast
and slow.
Figure 9. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 10) in the "ON"
position.
Figure 12. Throttle Lever
5. Grasp the starter grip (Figure 13) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding the compression point. Rewind the rope a little from
that point and pull out sharply.
CAUTI
CAUTION
Figure 10. Engine ON/Off Switch
DO NOT pull the starter rope all the way to the end
3. Place the Choke Lever (Figure 11) in the "OPEN" position.
D
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
Nnnn
Figure 11. Choke Lever
Figure 13. Starter Grip
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 17
MVC-88GH/GHW— INITIAL START-UP/OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
7. Before the compactor is put into operation run the engine for
3-5 minutes.
8. Check for abnormal engine noises or fuel leaks.
Stopping the Engine
CAUTI
CAUTION
D
NEVER stop the engine suddenly while working at high
speeds.
Operation
1. Place the throttle lever (Figure 12) in slow position, and
listen for the engine speed to decrease.
CAUTI
CAUTION
Make sure to follow all safety rules referenced in the safety
section of this manual before operating compactor. Keep work
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
2. Place the Engine ON/OFF switch (Figure 10) in the "OFF
" position.
3. Place the fuel valve lever (Figure 9) in the "OFF" position.
1. Once the engine has started, move the engine throttle lever
quickly to the fast position.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the centrifugal clutch.
NOTE
ALWAYS move the throttle lever
quickly without hesitation,
because increasing the engine
speed slowly causes the clutch
to slip.
5. Firmly gasp the compactor's handle bar with both hands , the
compactor will begin moving forward.
6. Slowly walk behind the compactor and be on the lookout for
any large objects or foreign matter that might cause damage
to the compactor or bodily injury.
l
7. Compactor traveling speed may drop on soils which contain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil. To
rectify this problem do the following:
■ Check the bottom plate to see if clay or equivalent material
has been lodge in the plate mechanism. If so, wash with
water and remove.
■ Remember the compactor does not work as efficiently on
clay or soils that have a high moisture content level.
■ If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
PAGE 18 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— MAINTENANCE
CAUTI
CAUTION
CAUTI
CAUTION
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shutdown.
Inspection and Maintenance Service Tables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 4 through 6.
CAUTI
CAUTION
Fuel piping and connections should be replaced every 2
years.
Table 4. Engine Maintenance Schedule
DESCRIPTION (3)
OPERATION
BEFORE
CHECK
X
FIRST
EVERY
MONTH 3 MONTHS
OR
OR
10 HRS.
25 HRS.
EVERY
6 MONTHS
OR
50 HRS.
EVERY
YEAR
OR
100 HRS.
EVERY
2 YEARS
OR
200 HRS.
Engine Oil
CHANGE
CHECK
X
X
Air Cleaner
CHANGE
All Nuts & Bolts
Re-tighten If
Necessary
X (1)
X
CHECK-CLEAN
X
Spark Plug
REPLACE
X
Cooling Fins
CHECK
X
Spark Arrester
CLEAN
X
Fuel Tank
CLEAN
X
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
X (2)
Valve Clearance
CHECK-ADJUST
Fuel lines
CHECK
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 19
MVC-88GH/GHW — MAINTENANCE
ENGINE OIL
TABLE 5. MACHINE INSPECTION
Item
Hours of Operation
Remarks
(Star ting check)
Every 8 hours (every
day)
Loosened or lost
screws
Every 8 hours (every
day)
Damage of any par t
Every 8 hours (every
day)
Function of controlling
system par t
Every 8 hours (every
day)
Vibrator oil check
Every 100 hours
See page 19.
Vibrator oil
replacement
Every 200 hours
See page 19.
V-belt (clutch) check
Every 200 hour
See page 19.
1. Drain the engine oil when the oil is warm as shown in
Figure 14.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten securely.
Daily Service
■ Check for leakage of fuel or oil.
■ Check engine oil.
■ Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening.
ENGINE AIR CLEANER
TABLE 6.
TIGHTENING TORQUE (in. kg/cm) Diameter
Material 6mm
8mm
10mm 12mm 14mm 16mm 18mm 20mm
4T
70
150
300
500
750
1,100
1,400
2,000
6-8T
100
250
500
800
1,300
2,000
2,700
3 ,8 0 0
11T
150
400
800
1,200
2,000
2,900
4,200
5,600
*
Figure 14. Engine Oil (Draining)
100 (6mm) 300 ~ 350 (8mm)l 650 ~ 700 (10mm)
* (In case counter-par t is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt,
and screw.
1. Remove the air cleaner cover and foam filter element as
shown in Figure 15.
2. Tap the paper filter element (Figure 15) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
element from the air cleaner case side. NEVER brush off dirt.
Brushing will force dirt into the fibers. Replace the paper filter
element if it is excessively dirty.
3. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engine oil and completely squeeze out the excess oil from the
element before installing.
PAGE 20 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— MAINTENANCE
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check the V-belt tension. Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
CAUTI
CAUTION
Whenever the compactor's vibration becomes weak or lost
during normal operation regardless of operation hours, check
the V-belt and clutch immediately.
■ Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway of V-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that the V-belt will come off.
Figure 15. Air Cleaner
CHANGING VIBRATOR OIL
1. When changing the vibrator oil, remove the drain plug
located at the bottom- right of the vibrator (Figure 5), and
simply tip the compactor to drain the oil. Note that the oil will
drain more easily while it is hot. Remember to use only
10W-30 motor oil when replaceing vibrator oil.
CAUTI
CAUTION
■ Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
■ Checking Clutch
Check the clutch simultaneously with V-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand (Figure 6) gets caught
between the V-belt and the clutch. Always use safety gloves.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 21
MVC-88GH/GHW— PREPARATION FOR LONG -TERM STORAGE
Plate Compactor Storage
For storage of the plate compactor for over 30 days, the
following is required:
■ Drain the fuel tank completelyor add STA-BIL to the fuel.
■ Run the engine until the fuel is completely consumed.
■ Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine Owner's
Manual for engine storage.
■ Completely drain the compactor's hydraulic oil from the
vibrating case.
■ Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
■ Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW—TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine , and Compactor
Troubleshooting (Tables 7, and 8) information shown below
and on the proceeding pages.
If the problem cannot be remedied, please leave the unit
just as it is and consult or company's service department.
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to star t, "fuel is available, but no
SPARK at spark plug".
POSSIBLE CAUSE
Spark plug bridging?
Check gap, insulation or
replace spark plug.
Carbon deposit on spark plug?
Clean or replace spark plug.
Shor t circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
ON/OFF switch is shor ted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Difficult to star t, "fuel is available, and Improper spark gap, points dir try?
SPARK is present at the spark plug".
Difficult to star t, "fuel is available, spark
is present and compression is normal"
Difficult to star t, "fuel is available, spark
is present and compression is low"
No fuel present at carburetor.
SOLUTION
Set correct spark gap and
clean points.
Condenser insulation worn or shor t
circuiting?
Replace condenser.
Spark plug wire broken or shor t circuiting?
R e p l a c e d e fe c t i ve s p a r k p l u g
wiring.
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Flush fuel system.
Air cleaner dir ty?
Clean or replace air cleaner.
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston rings and or
piston.
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spar k plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Fuel cock does not open properly?
Apply lubr icant to loosen fuel
cock lever, replace if necessary.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Clean or replace fuel tank cap.
Air in fuel line?
Bleed fuel line.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 23
MVC-88GH/GHW—TROUBLESHOOTING (ENGINE COMPACTOR)
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
"Weak in power" compression is
proper and does not misfire.
POSSIBLE CAUSE
SOLUTION
Air cleaner not clean?
Clean or replace air cleaner
Improper level in carburetor?
Check float adjustment, re-build
carbureator.
Defective Spark plug?
Clean or replace spark plug.
Defective Spark plug?
"Weak in power" compression is
proper but misfires.
Engine overheats.
Rotational speed fluctuates.
Recoil star ter malfunction.
l
Water in fuel system?
Flush fuel system, and replace
with correct type of fuel.
Dir ty spark plug?
Clean or replace spark plug.
Ignition coil defective?
Replace ignition coil.
Spark plug heat value improper?
Replace with correct type of
spark plug.
Correct type of fuel?
Replace with correct type of fuel
Cooling fins dir ty?
Clean cooling fins.
Governor adjusted correctly?
Adjust governor.
Governor spring defective?
Replace governor spring.
Fuel flow restricted?
C h e c k e n t i r e f u e l s y s t e m fo r
leaks or clogs.
Recoil mechanism clogged with dust and
dir t?
Clean recoil assembly with soap
and water.
Sprial spring loose?
Replace sprial spring.
TABLE 8. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Engine speed too low?
Set engine speed to correct RPM.
Clutch slips?
Check or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Travel speed too low, and vibration is Excessive oil in vibrator?
weak.
Drain excess oil and fill to proper level.
Malfunction in vibrator housing?
Check eccentric, gears and counter
weights.
Bearing Failure?
Replace Bearing
Insufficient engine output?
Check engine, compression etc.
PAGE 24 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
NOTE PAGE
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 25
MVC-88GH/GHW — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Section 1: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
NOTE
The contents of this catalog are
subject to change without notice.
Section 2: Items Found In the “Items Number” Column
All parts with same symbol in the number column:
*, #, +, %, or ■, belong to the same assembly or kit.
Note: If more than one of the same reference number is
listed, the last one listed indicates newest (or latest) part
available.
NOTE
If more than one of the same
reference number is listed, the last
one listed indicates newest (or
latest) part available.
l
PAGE 26 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW — SUGGESTED SPARE PARTS
MVC-88GH/GW 1 TO 5 UNITS WITH HONDA
GX160K1QMX2 ENGINE
1 to 5 Units
Qty.
P/N
Description
3 ......... o70100332 ....... V-BELT
1 ......... 060403060 ....... OIL SEAL, VIBRATING
2 ......... 050101000 ....... O-RING
5 ......... 9807956841 ..... SPARK PLUG
1 ......... 28462ZH8003 .. ROPE, RECOIL STARTER
1 ......... 36100ZE1015 .. SWITCH ASSY, ENGINE STOP
5 ......... 17210ZE1822 .. ELEMENT, A/C
1 ......... 17620ZH7023 .. CAP, FUEL TANK
1 ......... 17672ZE2W01 . FUEL FILTER, FUEL TANK
4 ......... 939010140 ....... SHOCK ABSORBER
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 27
MVC-88GH/GHW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
l
PAGE 28 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
PART NO
PART NAME
QTY. REMARKS
1
920206290
DECAL, READ OWNERS MANUAL ....... 1 ........ NPA-629
2
920203290
DECAL, CAUTION ................................. 1 ........ NPA-329
3
920208450
DECAL, LIFTING ................................... 1 ........ NPA-845
4
920203060
DECAL, CAUTION (START ENG/VIBR) . 1 ........ NPA-306
5
920208350
DECAL, V- BELT RPF-3330 ................... 1 ........ NPA-835
6
920201580
DECAL, MQ LOGO ................................ 2 ........ NPA-158
7
920106460
DECAL, MIKISA LOGO (NAME) ............ 1 ........ NPA-507
8
920201950
DECAL, MOTOR OIL .............................. 1 ........ NPA-195
9
920101410
DECAL, MIKISA LOGO (TRIANGLE) ....1 ........ NPA-141
10
PLATE, SERIAL NO./MVC-MQ ..............1 ........ CONTACT MQ PARTS DEPT. W/MODEL & S/N
11
920203330
EAR PROTECTION LABEL ................... 1 ........ NPA-333
SEE DECAL ILLUSTRATIONS PAGE.
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 29
MVC-88GH/GHW— BODY ASSY.
VIBRATING PLATE ASSY.
l
PAGE 30 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— BODY ASSY.
BODY
NO
21
23
24
25
31
32
33
35
36
37
38
39
40
41
42
43
45
46
47
48
49
51
52
53
54
55
56
57
91
92
93
94
95
96
97
101
102
103
ASSY.
PART NO
416115971
939010140
020310080
030210250
416115980
001221025
030210250
912216006
001220845
030208200
031108160
404412290
416452780
031108160
022710809
959404350
416338990
951010170
416452800
952400130
009110004
070100332
416115950
416116000
001220825
030208200
031108160
001220820
416115930
416452730
404433430
416452360
952405600
001211253
030212300
416115940
001221025
030210250
PART NAME
VIBRATING PLATE
SHOCK ABSORBER 50D-45H
NUT M10
WASHER SW M10
BASE
BOLT 10X25 T
WASHER, LOCK M10
ENGINE ASSY. GX160K1QMX2
BOLT 8X45 T
WASHER, LOCK M8
WASHER, FLAT M8
ENGINE NUT
ENGINE NUT (W/BOLT)
WASHER, FLAT M8
NYLON NUT M8
EARTH WIRE
CLUTCH ASSY.
KEY 4.77X4. 77X35
COLLAR 19.05-25-15.6
WASHER
SOCKET HEAD BOLT 5/16X24
V-BELT RPF-3330
BELT COVER (INSIDE)
BELT COVER
BOLT 8X25 T
WASHER, LOCK M8
WASHER, FLAT M8
BOLT 8X20 T
HANDLE
COLLAR 13-20-44
RUBBER 20X32X28.5/52H
HANDLE STOPPER
WASHER 12.5X35X4.5
BOLT 12X65 H
WASHER, LOCK M12
GUARD HOOK /MVC-88
BOLT 10X25 T
WASHER, LOCK M10
QTY.
1
4
4
4
1
4
4
1
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
4
5
1
1
1
2
2
2
2
2
2
1
4
4
REMARKS
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 31
MVC-88GH/GHW— VIBRATOR ASSY.
VIBRATOR ASSY.
l
PAGE 32 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— VIBRATOR ASSY.
VIBRATOR ASSY.
NO
PART NO
61
416115990
62
953400270
63
953405260
64
001221635
65
030216400
66
031116260
68
416338890
69
040306211
70
416338900
71
416338910
72
416338920
73
060403060
74
050101000
75
001220825
76
030208200
78
416452720
79
951405240
80
952404250
81
001221025
82
030210250
PART NAME
VIBRATING CASE
PLUG 1/4X14 10L
PACKING 1/4
BOLT 16X35 T
WASHER, LOCK M16
WASHER, FLAT M16
ECCENTRIC ROTATOR
BEARING 6211C3
CASE COVER (R)
CASE COVER (L)
BELT COVER GUARD
OIL SEAL TC-35488
O-RING G-100
BOLT 8X25 T
WASHER, LOCK M8
PULLEY A1-30-86-20B
KEY 7X7X19 R
WASHER 11X40X4
BOLT 10X25 T
WASHER, LOCK M10
QTY.
1
1
1
4
4
4
1
2
1
1
1
1
2
8
8
1
1
1
1
1
REMARKS
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 33
MVC-88GH/GHW— SPRINKLER ASSY. (OPTION)
SPRINKLER ASSY. (OPTION)
l
PAGE 34 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— SPRINKLER ASSY. (OPTION)
SPRINKLER ASSY. (OPTION)
NO
111
111A
*
112
*
113
*
114
*
115
*
116
*
117
*
118
*
119
*
120
*
121 #
*
122 #
*
123 #
*
124 #
*
125 #
*
PART NO
4169100109
416910010
033910050
953406390
954403241
416338930
416338940
416452750
001740825
416453780
416452790
954300340
001241030
033910010
022910180
416453800
PART NAME
QTY.
REMARKS
WATER TANK ASSY. .................... 1 ............... INCLUDES ITEMS W/
*
WATER TANK (W/CAP ONLY) ...... 1 ............... REPLACES 416116010 INCLUDES ITEMS W/#
WASHER 14.5X30X1.6
1
PACKING 13X28X2
1
COCK PT1/4
1
SPRINKLING PIPE
1
PIPE HOLDER (L)
1
PIPE HOLDER (R)
1
FLANGE BOLT 8X25
2
PACKING 8X19X2T
3
STAY, PIPE HOLDER
1
CAP, WATER TANK
1
BOLT 10X30
1
WASHER 10.5X21X2
2
NYLON NUT M10
1
SEAT PACKING
2
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 35
MVC-88GH/GHW— TRANSPORT WHEEL ASSY. (OPTION)
TRANSPORT WHEEL ASSY. (OPTION )
l
PAGE 36 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
MVC-88GH/GHW— TRANSPORT WHEEL ASSY. (OPTION)
TRANSPORT WHEEL ASSY. (OPTION )
NO
1
2
3
4
5
6
PART NO
416116160
959404310
031120320
025203030
416454150
025403025
PART NAME
WHEEL SHAFT
WHEEL 150X42
WASHER, FLAT M20
SPLIT COTTER PIN 3X30
ROLLER
SPRING PIN 3X25
QTY.
1
2
2
2
2
3
REMARKS
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 37
HONDA GX160K1QMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
l
PAGE 38 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO. PART NO.
1
12210ZH8000
2
* 12204ZE1306
3
12205ZE1315
*
4 #
* 12216ZE5300
5
12251ZF1800
6
12310ZE1010
7
12391ZE1000
8
15721ZH8000
9
90016ZE1000
10
90043ZE1020
11
90047ZE1000
12
9430110160
14
957230806000
15
9807955846
15
9807956846
PART NAME
QTY. REMARKS
CYLINDER HEAD......................................... 1 ...... INCLUDES ITEMS W/
*
GUIDE, VALVE (OS) (OPTIONAL)
1
GUIDE, EX. VALVE (OS) (OPTIONAL) ........ 1 ...... INCLUDES ITEMS W/#
CLIP, VALVE GUIDE
1
GASKET, CYLINDER HEAD
1
COVER, HEAD
1
GASKET, CYLINDER HEAD COVER
1
TUBE, BREATHER
1
BOLT, FLANGE (6 X 13)
4
BOLT, STUD ( 6 X 109)
2
BOLT, STUD (8 X 32)
2
PIN A, DOWELL (10 X 16)
2
BOLT, FLANGE (8 X 60)
4
SPARK PLUG (BPR5ES) (NGK)
1
SPARK PLUG (BPR6ES) (NGK)
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 39
HONDA GX160K1QMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
l
PAGE 40 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO. PART NO.
2
12000ZH8811
3
15510ZE1023
3
15510ZE1033
4
16510ZE1000
5#
16511ZE1000
16512ZE1000
6#
8
16531ZE1000
10
90131ZE1000
11
90451ZE1000
12
90601ZE1000
13
90602ZE1000
14
91001ZF1003
* 91202883005
15
* 91353671003
16
17
9405010000
18
9410106800
19
9425108000
20
957010601200
PART NAME
QTY. REMARKS
CYLINDER ASSY. (OIL ALERT) ................... 1 ...... INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL ........................ 1 ...... USE UP TO ENGINE S/N 4367320
SWITCH ASSY., OIL LEVEL ........................ 1 ...... USE FROM ENGINE S/N 4367321
GOVERNOR ASSY. ...................................... 1 ...... INCLUDES ITEMS W/#
WEIGHT, GOVERNOR
2
HOLDER, GOVERNOR WEIGHT
1
SLIDER, GOVERNOR
1
BOLT, DRAIN PLUG
2
WASHER, THRUST (6MM)
1
WASHER, DRAIN PLUG (10.2MM)
2
CLIP, GOVERNOR HOLDER
1
BEARING, RADIAL BALL (6205)
1
OIL SEAL (25 X 41 X 6)
1
O-RING (13.5 X 1.5) (ARAI)
1
NUT, FLANGE (10MM)
1
WASHER, PLAIN (6MM)
2
PIN, LOCK (8MM)
1
BOLT, FLANGE (6 X 12)
2
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 41
HONDA GX160K1QMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
l
PAGE 42 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO. PART NO.
1
11300ZE1641
3
11381ZH8801
4
15600ZE1003
5
15600ZG4003
9#
15625ZE1003
10+
15625ZE1003
11
91202883005
*
12
9430108140
13
957010803200
14
961006205000
*
PART NAME
QTY. REMARKS
COVER ASSY., CRANKCASE (U-TYPE) ..... 1 ...... INCLUDES ITEMS W/
*
GASKET, CASE COVER
1
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/#
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/+
GASKET, OIL FILLER CAP
1
GASKET, OIL FILLER CAP
1
OIL SEAL (25 X 41 X 6)
1
PIN A, DOWEL (8 X 14)
2
BOLT, FLANGE (8 X 32)
6
BEARING, RADIAL BALL (6205)
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 43
HONDA GX160K1QMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
l
PAGE 44 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO. PART NO.
4
13310ZE1601
13
90003ZE1000
14
90473842000
15
90745ZE1600
PART NAME
QTY. REMARKS
CRANKSHAFT (Q-TYPE)
1
BOLT, HEX 5/16” ............................................ 1 .... USE FROM S/N 6745959
WASHER, 8 MM ............................................. 1 .... USE FROM S/N 6745959
KEY, 78 X 38 MM
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 45
HONDA GX160K1QMX2 ENGINE — PISTON/RINGS ASSY.
PISTON/RINGS ASSY.
l
PAGE 46 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — PISTON/RINGS ASSY.
PISTON/RINGS ASSY.
NO. PART NO.
1
13010ZH8941
1
13011ZH8941
1
13012ZH8941
1
13013ZH8941
2
13101ZH8000
2
13102ZH8000
2
13103ZH8000
2
13104ZH8000
3
13111ZE1000
4
13200ZE1010
5
90001ZE1000
*
6
90551ZE1000
PART NAME
QTY.
REMARKS
RING SET, PISTON (STD)
1
RING SET, PISTON (OS 0.25)
1
RING SET, PISTON (OS 0.50) ............. 1 ......... USE FROM ENGINE S/N 4733211
RING SET, PISTON (0.75) OPTION 1
PISTON (STD)
1
PISTON (OS 0.25)
1
PISTON (OS 0.50)
1
PISTON (0.75)
1
PIN, PISTON
1
ROD ASSY., CONNECTING ................ 1 ......... INCLUDES ITEMS W/
*
BOLT, CONNECTING ROD
2
CLIP, PISTON PIN (18MM)
2
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 47
HONDA GX160K1QMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
l
PAGE 48 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO. PART NO.
1
14100ZE1812
2
14410ZE1010
3
14431ZE1000
4
14441ZE1010
5
14451ZE1013
6
* 14568ZE1000
7
14711ZF1000
8
14721ZF1000
9
14751ZF1000
10
14771ZE1000
11
14773ZE1000
12
14781ZE1000
13
14791ZE1010
14
90012ZE0010
15
90206ZE1000
PART NAME
QTY. REMARKS
CAMSHAFT ASSY. ...................................... 1 ...... INCLUDES ITEMS W/
*
ROD, PUSH
2
ARM, VLAVE ROCKER
2
LIFTER, VALVE
2
PIVOT, ROCKER ARM
2
SPRING, WEIGHT RETURN
1
VALVE, IN.
1
VALVE, EX. (STELITE)
1
SPRING VALVE
2
RETAINER, IN. VALVE SPRING
1
RETAINER, EX. VALVE SPRING
1
ROTATOR, VALVE
1
PLATE, PUSH ROD GUIDE
1
BOLT, PIVOT (8MM)
2
NUT, PIVOT ADJ.
2
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 49
HONDA GX160K1QMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
l
PAGE 50 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO. PART NO.
1
28400ZH8013ZB
2
28410ZH8003ZB
*
3
* 28420ZH8013
4
* 28422ZH8013
5
* 28433ZH8003
6
* 28441ZH8003
7
28442ZH8003
*
8
* 28443ZH8003
9
* 28461ZH8003
28462ZH8003
10
*
11
* 90003ZH8003
12
90008ZE2003
PART NAME
QTY. REMARKS
STARTER ASSY., RECOIL “NH1”(BLACK) ............ 1 ..... INCLUDES ITEMS W/
*
CASE, RECOIL STARTER “NH1”(BLACK)
1
REEL, RECOIL STARTER
1
RATCHET, STARTER
2
GUIDE, RATCHET
1
SPRING, FRICTION
1
SPRING, RECOIL STARTER
1
SPRING, RETURN
2
KNOB, RECOIL STARTER
1
ROPE, RECOIL STARTER
1
SCREW, SETTING
1
BOLT, FLANGE (6 X 10)
3
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 51
HONDA GX160K1QMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
l
PAGE 52 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO. PART NO.
2
19610ZE1000ZC
4
19612ZH8811
7
90601ZH7013
8
19630ZH8000
11
36100ZE1015
11
36100ZH7003
13
90013883000
14
90022888010
17
34150ZH7003
19
957010600800
PART NAME
QTY.
REMARKS
COVER, FAN *NH1* (BLACK)
1
PLATE, SIDE (OIL ALERT)
1
CLIP, HARNESS
1
SHROUD
1
SWITCH ASSY., ENGINE STOP ........... 1.......... USE UP TO S/N 4368640
SWITCH ASSY., ENGINE STOP ........... 1.......... USE FROM 4368641
BOLT, FLANGE (6 X 12) (CT200)
6
BOLT, FLANGE (6 X 20) (CT200)
1
ALERT UNIT, OIL
1
BOLT, FLANGE (6 X 8)
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 53
HONDA GX160K1QMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
l
PAGE 54 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO. PART NO.
1
16010ZE1812
16011ZE0005
2
*
3
* 16013ZE0005
4
* 16015ZE0831
5
* 16016ZH7W01
6
* 16024ZE1811
7
16028ZE0005
*
8
* 16044ZE0005
9
* 16100ZH8W51
10
16124ZE0005
*
11
* 16166ZH8W50
12
* 16173001004
13
16211ZE1000
14
16212ZH8800
15
16220ZE1020
16
16221ZH8801
17
16610ZE1000
18
16953ZE1812
*
19
* 16954ZE1811
20
16956ZE1811
*
21
* 16957ZE1812
22
* 16967ZE0811
23
93500030060H
*
24#
9430520122
25
99101ZH80650
25
99101ZH80680
25
* 99101ZH80700
26
99204ZE00350
*
PART NAME
QTY. REMARKS
GASKET SET
1
VALVE SET, FLOAT
1
FLOAT SET
1
CHAMBER SET, FLOAT
1
SCREW SET
1
SCREW SET, DRAIN
1
SCREW SET B
1
CHOKE SET
1
CARBURETOR ASSY. (BE65B B) ................ 1 ...... INCLUDES ITEMS W/
*
SCREW, THROTTLE STOP
1
NOZZLE, MAIN
1
O-RING
1
INSULATOR, CARBURETOR
1
GASKET, INSULATOR
1
SPACER, CARBURETOR
1
GASKET, CARBURETOR
1
LEVER, CHOKE (STD) ................................ 1 ...... INCLUDES ITEMS W/#
LEVER, VALVE
1
PLATE, LEVER SETTING
1
SPRING, VALVE LEVER
1
GASKET, VALVE
1
CUP, FUEL STRAINER
1
SCREW, PAN (3 X 6)
2
PIN, SPRING (2 X 12)
1
JET, MAIN (#65) OPTIONAL
1
JET, MAIN (#68) OPTIONAL
1
JET, MAIN (#70)
1
JET, SET, PILOT (#35)
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 55
HONDA GX160K1QMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
l
PAGE 56 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER (DUAL) ASSY.
NO. PART NO.
1
16271ZE1000
2
17210ZE1505
3
* 17218ZE1505
4
17230ZE1820
5
17232891000
*
17238ZE7010
6#
7#
17239ZE1000
8
17410ZE1020
9
90201415000
10
17235ze1831
11
90325044000
13
957010602000
PART NAME
QTY. REMARKS
GASKET, ELBOW ........................................ 1 ...... INCLUDES ITEMS W/
*
ELEMENT, AIR CLEANER (DUAL)
1
FILTER (OUTER)
1
COVER, AIR CLEANER (DUAL)
1
GROMMET, AIR CLEANER
1
COLLAR, AIR CLEANER
2
COLLAR B, AIR CLEANER
1
ELBOW, AIR CLEANER ............................... 1 ...... INCLUDES ITEMS W/#
NUT, CAP (6 MM)
2
NOSE, MUFFLER
1
WINGNUT, TOOL BOX SETTING
2
BOLT, FLANGE (6 X 20)
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 57
HONDA GX160K1QMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
l
PAGE 58 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO. PART NO.
1
18310ZH8810
1
18310ZK8V50
3
18320ZF1H01
5
18331883810
7
18355ZE1000
8
18381ZH8800
11
90050ZE1000
12
90055ZE1000
13
18522ZE1000
15
94001080000S
30
90002ZG0003
PART NAME
QTY. REMARKS
MUFFLER..................................................... 1 ...... USE UP TO S/N 6745959
MUFFLER..................................................... 1 ...... USE FROM S/N 6745959
PROTECTOR, MUFFLER
1
CAP, MUFFLER
1
ARRESTER, SPARK
1
GASKET, MUFFLER
1
SCREW, TAPPING (5 X 8)
4
SCREW, TAPPING (4 X 6)
1
GUIDE, MUFFLER
1
NUT, HEX (8MM)
2
SCREW, TAPPING (4 X 8)
2
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 59
HONDA GX160K1QMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
l
PAGE 60 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
NO. PART NO.
10
16854ZH8000
17
16955ZE1000
20
17510ZE1020ZF
21
17620ZH7023
23
17631ZH7003
* 17672ZE2W01
24
29
91353671003
33
9405006000
36
950014500360M
40
43
44
45
9500202080
957010602500
90404680000
91319ME5003
PART NAME
QTY. REMARKS
RUBBER, SUPPORTER (107MM)
1
JOINT, FUEL TANK
1
TANK, FUEL *NH1* (BLACK)
1
CAP, FUEL FILLER ...................................... 1 ...... INCLUDES ITEMS W/
*
GASKET, FUEL FILLER CAP
1
FILTER, FUEL
1
O-RING (13.5 X 1.5) (ARAI)
1
NUT, FLANGE (6MM)
2
BULK HOSE, FUEL (4.5 X 3000)
1
(4.5 X 140)
CLIP, TUBE (B8)
2
BOLT, FLANGE (6 X 25)
1
WASHER ...................................................... 2 ...... USE FROM S/N 6745959
O-RING ......................................................... 2 ...... USE FROM S/N 6745959
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 61
HONDA GX160K1QMX2 ENGINE — COOLING FAN & FLYWHEEL ASSY.
COOLING FAN & FLYWHEEL ASSY.
l
PAGE 62 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — COOLING FAN & FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO. PART NO.
1
13331357000
2
19511ZE1000
4
28451ZH8003
5
31100ZE1010
5
31100ZE1810
8
90201878003
PART NAME
KEY, SPECIAL WOODRUFF (25 X 18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
FLYWHEEL (LAMP)
NUT, SPECIAL (14MM)
QTY.
1
1
1
1
1
1
REMARKS
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 63
HONDA GX160K1QMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
l
PAGE 64 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO. PART NO.
1
30500ZE1033
2
30700ZE1013
7
36101ZE1010
11
90121952000
PART NAME
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE (6 X 25)
QTY.
1
1
1
2
REMARKS
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 65
HONDA GX160K1QMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
l
PAGE 66 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO. PART NO.
2
16500ZH8813
4
16551ZE0010
5
16555ZE1000
6
16561ZE1020
7
16562ZE1020
9
* 16571ZH8020
10
16574ZE1000
*
11
* 16575ZH8000
12
* 16576891000
16578ZE1000
13
*
14
* 16580ZH8813
15
* 16584883300
16
* 16592ZE1810
17
* 16594883010
21
90013883000
22
90015ZE5010
24
90114SA0000
* 93500050250H
25
* 90605230000
26
* 93500040060H
27
* 93500050160A
28
* 9405006000
29
PART NAME
QTY. REMARKS
CONTROL ASSY. ......................................... 1 ...... INCLUDES ITEMS W/
*
ARM, GOVERNOR
1
ROD, GOVERNOR
1
SPRING, GOVERNOR
1
SPRING, THROTTLE RETURN
1
LEVER CONTROL
1
SPRING LEVER
1
WASHER, CONTROL LEVER
1
HOLDER, CABLE
1
SPACER, CONTROL LEVER
1
BASE CONTROL
1
SPRING, CONTROL ADJUSTING
1
SPRING, CABLE RETURN
1
HOLDER, WIRE
1
BOLT, FLANGE (6 X 12) (CT200)
2
BOLT, GOVERNOR ARM
1
NUT, SELF-LOCK (6MM)
1
SCREW, PAN (5 X 25)
1
CIRCLIP
1
SCREW, PAN (5 X 25)
1
SCREW, PAN (5 X 16)
1
NUT, FLANGE (6MM)
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 67
HONDA GX160K1QMX2 ENGINE — GASKET KIT ASSY.
NO ARTWORK AVAILABLE
l
PAGE 68 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO. PART NO.
1
06111ZH8405
2
11381ZH8801
*
3
* 12251ZF1800
4
* 12391ZE1000
5
16212ZH8800
*
6
* 16221ZH8801
7
18381ZH8800
*
PART NAME
QTY.
REMARKS
GASKET KIT ............................................. 1 .......... INCLUDES ITEMS W/
*
GASKET, CASE COVER
1
GASKET, CYLINDER HEAD
1
GASKET, CYLINDER HEAD COVER
1
GASKET, INSULATOR
1
GASKET, CARBURETOR
1
GASKET, MUFFLER
1
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 69
HONDA GX160K1QMX2 ENGINE — LABELS ASSY.
LABELS ASSY.
l
PAGE 70 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
HONDA GX160K1QMX2 ENGINE — LABELS ASSY.
LABELS ASSY.
NO. PART NO.
1
87521ZH8020
3
87522zh9010
6
87528ZE1810
8
87532ZH8810
PART NAME
EMBLEM (5.5)
LABEL, CAUTION
MARK, CHOKE
MARK, OIL ALERT (E)
QTY.
1
1
1
1
REMARKS
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 71
TERMS AND CONDITIONS OF SALE — PARTS
Effective: October 1, 2000
PAYMENT TERMS
5.
Parts must be in new and resalable condition, in the original Multiquip package (if
any), and with Multiquip part numbers
clearly marked.
6.
The following items are not returnable:
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being replaced by another item, it is obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were purchased more than six months prior to
the return date.
MINIMUM ORDER
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original Equipment Manufacturer accounts who
use our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoice
for special handling including bus shipments,
insured parcel post or in cases where Multiquip
must personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
RETURNED GOODS POLICY
d. Special order items.
Return shipments will be accepted and credit
will be allowed, subject to the following provisions:
e. Electrical components.
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental damages.
f. Paint, chemicals, and lubricants.
LIMITATION OF WARRANTIES
g. Decals and paper products.
1.
h. Items purchased in kits.
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not manufactured by Multiquip. Such warranties made in
connection with the sale of new, complete units
are made exclusively by a statement of warranty packaged with such units, and Multiquip
neither assumes nor authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products. Apart from such written statement of
warranty, there are no warranties, express,
implied or statutory, which extend beyond the
description of the products on the face hereof.
The minimum charge for orders from Multiquip is $15.00 net. Customers will be asked
for instructions regarding handling of orders
not meeting this requirement.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quantities, and descriptions of the items to be
returned.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
l
c. The list must state the reason(s) for
the return.
d. The list must reference the sales
order(s) or invoice(s) under which the
items were originally purchased.
e. The list must include the name and
phone number of the person requesting the RMA.
3.
A copy of the Return Material Authorization must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
c. Any line item with an extended dealer
net price of less than $5.00.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for five working
days from notification, pending instructions. If a reply is not received within five
days, the material will be returned to the
sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific date and all orders received on or after that
date will be billed at the revised price. Rebates
for price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
PAGE 72 — MVC-88GH/GHW — PARTS & OPERATION MANUAL — REV. #4 (10/15/04)
NOTE PAGE
MVC-88GH/GHW— PARTS & OPERATION MANUAL — REV. #4 (10/15/04) — PAGE 73
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Email: mq@multiquip.com
Internet: www.multiquip.com
PARTS DEPARTMENT
800-427-1244
310-537-3700
MAYCO PARTS
800-306-2926
310-537-3700
SERVICE DEPARTMENT
800-421-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
800-421-1244
FAX: 310-537-3927
FAX: 800-672-7877
FAX: 310-637-3284
FAX: 800-672-7877
FAX: 310-637-3284
FAX: 310-537-4259
FAX: 310-631-5032
FAX: 310-537-1173
manufactured for Multiquip Inc.
by
MIKASA SANGYO CO., LTD. Tokyo, Japan
Your Local Dealer is:
MULTIQUIP INC..
18910 WILMINGTON AVE.
CARSON, CALIFORNIA 90746
800-421-1244 • 310-537-3700
FAX: 310-537-3927
E-mail:mq@multiquip.com
Internet:multiquip.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising