Extron electronics | VersaTools MDA 5A RCA | User`s manual | Extron electronics VersaTools MDA 5A RCA User`s manual

Extron electronics VersaTools MDA 5A RCA User`s manual
User’s Manual
VersaTools® MDA 3 Series
Video and Audio Mini Video Distribution Amplifiers
www.extron.com
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
© 2006 Extron Electronics. All rights reserved.
68-607-01 Rev. D
06 06
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
FCC Class A Notice
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense.
Note: These units was tested with shielded cables on the peripheral devices and
between the transmitter and receiver. Shielded cables must be used with the units to
ensure compliance.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Introduction ................................................................................ 1
Installation ................................................................................... 2
Rack mounting ............................................................................ 2
Back of the rack mounting ........................................................ 4
Furniture or projector mounting ............................................. 6
Connections, Controls, and Indicator ............................ 7
S-video (MDA 3SV, MDA 3SVA, MDA 3SV Dual) ..................... 7
Composite video (MDA 3V, MDA 3AV, MDA 3V Dual) ........... 8
Audio on captive screw connectors
(MDA 3AV, MDA 3SVA, MDA 3A) ............................................ 8
Audio on RCA connectors (MDA 3A RCA) ............................ 10
Power (all models) .................................................................. 10
Specifications ........................................................................... 12
All trademarks mentioned in this manual are the properties of their respective owners.
68-607-01 Rev. D
06 06
VersaTools® MDA 3 Series • Table of Contents
i
Table of Contents, cont’d
Introduction
The Extron MDA 3 Series of Mini Distribution Amplifiers
(MDAs) are a family of eight one-input, three-output, video and
audio distribution amplifiers. The MDA series distribution
amplifiers (DAs) split one composite video or S-video input
and/or audio input for output to multiple destinations with no
loss of signal quality. The MDA are members of the Extron
VersaTools® line of basic distribution amplifiers, switchers, and
associated video accessories.
The MDAs distribute composite video, S-video (luminance (Y)
and chrominance (C)), and/or balanced or unbalanced audio on
captive screw connectors, or unbalanced audio on RCA
connectors, in the following combinations:
sc
Co
re
w Au
co A
co di
nn ud
nn o (
te
Sc
ec io
ec a
vi
vi
to (R
to pt
de
de
i
rs CA
rs ve
o
o
)
)
Part #
m
po
si
Distribution
Amplifier
MDA 3SV
60-444-01
MDA 3SVA
60-444-20
MDA 3SV Dual
60-444-10
MDA 3V
60-439-01
MDA 3AV
60-439-20
MDA 3V Dual
60-439-10
MDA 3A
60-440-01
MDA 3A RCA
60-440-30
2
2
2 = Two separate DAs.
The MDAs ship with external desktop 12 V power supplies that
accept 100 to 240 VAC, 50 Hz or 60 Hz input.
ii
VersaTools® MDA 3 Series • Table of Contents
®®
VersaTools
VersaTools
MDA
MDA33Series
Series• •Introduction
Installation
1
VersaTools® MDA 3 Series, cont’d
Installation
The MDA 3 Series mini distribution amplifiers (DAs) can be
mounted on a rack shelf, to a rack without a shelf, under a desk
or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the MDA on any of the
following rack shelves:
•
RSF 123 VersaTools® rack shelf kit (part #60-190-20)
(figure 1)
•
RSB 123 VersaTools rack shelf (part #60-604-20)
•
RSU 126 6" deep universal rack shelf kit (part #60-190-10)
•
RSB 126 6" deep basic rack shelf (part #60-604-10)
•
RSU 129 1U universal rack shelf kit (part #60-190-01)
(figure 2)
•
RSB 129 1U basic rack shelf (part #60-604-01)
On the standard rack shelf, the MDA mounts in one of four
locations to the rear of the rack or in one of four locations to the
front of the rack.
1.
If feet were previously installed on the bottom of the
MDA, remove them.
2.
Mount the MDA on the rack shelf, using two 4-40 x 3/16"
screws in opposite (diagonal) corners to secure the MDA
to the shelf.
DI
ST
RI
BU
TIO
N
AM
PL
IFI
ER
VersaTools Rack Shelf
DI
ST
RI
BU
TIO
N AM
PL
IFI
ER
1/4 Rack Width False Front
Face Plate
Use 2 mounting holes on
opposite corners.
DI
ST
RI
BU
TIO
N
IFI
ER
(2) 4-40 x 3/16" Screws
Figure 1 — Rack mounting the MDAs on a
VersaTools rack shelf
DIST
DIST
RIBU
TIO
N AM
PL
IFI
Install blank panel(s) or other unit(s) to the rack shelf.
Only products in the VersaTools line can be mounted to a
VersaTools shelf. Any 1U rack-mountable Extron
product can be mounted on the standard shelf.
RIBU
TIO
N AM
PL
IFI
ER
ER
DIST
3.
AM
PL
RIBU
TIO
N AM
PL
IFI
ER
DIS
MD
A
TR
IBU
SE
RIE
N
S
TIO
AM
PL
IFIER
Figure 2 — MDAs mounted on a standard rack
shelf
2
VersaTools® MDA 3 Series • Installation
VersaTools® MDA 3 Series • Installation
3
VersaTools® MDA 3 Series, cont’d
Back of the rack mounting
The MDA can be mounted to the rear of a rack using the Extron
MBB 100 VersaTools® back of the rack mounting kit
(part #70-367-01) (figure 3). The kit allows the product to be
vertically mounted to the front or rear rack supports and facing
either towards the front or the rear of the rack.
Rear
DISTRIBUTION AMPLIFIER
Front
IR
1
2
3
4
INP
UTS
5
6
7
8
1
2
3
OU
4
TP
UTS
5
6
7
8
EN
TE
R
PR
ES
ET
AV
MA
VS
E
RI
X SW RIE
ITCH S
MAT
I/O
VID
AU
D
ER
+d
B
-d
B
AU
DIO
SE
TU
P
Figure 3 — Attaching the back of the rack kit
1.
Remove feet from the bottom of the MDA if they are
installed.
2.
Remove two screws from one side of the unit. Retain the
screws for possible later reassembly without the bracket.
3.
Attach one bracket to the side of the unit using the longer
screws included in the kit.
4.
Repeat steps 2 and 3 on the other side of the unit.
5.
Mount the unit to the rack using the two included rack
screws (figure 4). The MDA can be vertically mounted
facing in either direction.
Figure 4 — Typical back of the rack installations
Only VersaTools products and most IP Link products
can be mounted using the back of the rack mounting kit.
4
VersaTools® MDA 3 Series • Installation
VersaTools® MDA
VersaTools
3 Series® •MDA
Connections
3 Series •and
Installation
Controls
5
VersaTools® MDA 3 Series, cont’d
Furniture or projector mounting
8.
Furniture mount or projector mount the MDA using the
optional Extron MBU 123 VersaTools® under desk mounting kit
(part #70-212-01); or VersaTools® PMK 100 mini projector
mounting kit (part #70-217-01) as follows:
Attach the mounting brackets to the MDA with the
machine screws provided (figure 5).
1.
For projector mounting, secure the MDA to a projector
mount or other surface by inserting the mounting bolt
through the bracket’s slotted hole.
Connections, Controls, and Indicator
See figure 6, figure 7, and figure 11 to make the following connections. The
figures show all of the combinations of connectors that you may encounter
with your MDA.
S-video (MDA 3SV, MDA 3SVA, MDA 3SV Dual)
Projector
Mounting
Bracket
Mounting
Bolt
1
Projector
Input connector (s) — Connect an S-video input to this 4-pin
mini DIN connector (figure 6 and figure 7). On the Dual model
(figure 7), Input A and Input B are completely separate inputs to
two separate distribution amplifiers.
MDA 3SVA
DI
ST
RI
BU
TIO
N
1
2
INPUT
OUTPUTS
MDA 3SVA,
Rear Panel
1
POWER
AM
PL
IFIE
R
12V
.5A MAX
2
OUTPUTS
INPUT
L
R
L
1
R
L
R
2
L
3
BAL
3
R
1 2 3
UNBAL
Under Desk Mounting
Projector Mounting
Figure 5 — Desk and projector mounting the MDAs
6
2.
If feet were previously installed on the bottom of the
MDA, remove them.
3.
For furniture mounting, hold the MDA with the attached
brackets against the underside of the table or other
furniture. Mark the location of the screw holes of the
bracket on the mounting surface.
4.
For furniture mounting, drill 3/32" (2 mm) diameter pilot
holes, 1/4" (6.3 mm) deep in the mounting surface at the
marked screw locations.
5.
For furniture mounting, insert #8 wood screws into the
four pilot holes. Tighten each screw into the mounting
surface until just less than 1/4" of the screw head
protrudes.
6.
For furniture mounting, align the mounting screws with
the slots in the brackets and place the MDA against the
surface, with the screws through the bracket slots.
7.
For furniture mounting, slide the MDA slightly forward or
back, then tighten all four screws to secure the MDA in place.
VersaTools® MDA 3 Series • Installation
Connections and Controls
10
6
5
MDA 3AV,
Rear Panel
7
4
3
MDA 3AV
O
U
T
I
N
1
POWER
12V
.34A MAX
2
OUTPUTS
INPUT
L
R
L
1
R
L
2
R
L
3
BAL
3
R
1 2 3
UNBAL
10
5
6
7
Figure 6 — MDA 3 Series front and rear panels
2
Out connector or Outputs (1 through 3) connectors — Connect
up to three S-video devices to these 4-pin mini DIN connectors.
On the Dual model, the A output signals are identical to the A
input, and the B output signals are identical to the B input.
VersaTools® MDA
VersaTools
3 Series® •MDA
Connections
3 Series •and
Installation
Controls
7
VersaTools® MDA 3 Series, cont’d
POWER
12V
.5A MAX
Balanced Stereo Input
(high impedance)
2
3
(high impedance)
1
2
OUTPUTS
3
Figure 8 — Captive screw input connector wiring
B
INPUT
MDA 3V Dual,
Rear Panel
Unbalanced Stereo Input
Do not tin the wires!
1
R
A
L
0.2” (5 mm) max.
Tip
Ring
Sleeve (s)
Tip
Ring
R
Tip
Sleeve
MDA 3SV
DUAL
10
Tip
Sleeve
2
1
L
MDA 3SV Dual,
Rear Panel
1
2
3
4
When making connections for the MDA from existing
audio cables, see figure 9. A mono audio connector
consists of the tip and sleeve. A stereo audio connector
consists of the tip, ring and sleeve. The ring, tip, and
sleeve wires are also shown on the captive screw audio
connector diagrams, figure 8 and figure 10.
Tip
MDA 3V
DUAL
Sleeve
Tip (Left)
Sleeve (Gnd)
A
1
POWER
12V
.5A MAX
2
Ring (Right)
Tip (Left)
3
Tip (Signal)
B
INPUT
1
2
OUTPUTS
Sleeve (Gnd)
Unbalanced Mono
3
Sleeve (Gnd)
Unbalanced Stereo
Figure 9 — Phono audio connectors
10
3
4
Figure 7 — MDA 3SV Dual and MDA 3V Dual rear
panels
Composite video (MDA 3V, MDA 3AV, MDA 3V Dual)
5
8
Tip
Ring
Right
Tip
Ring
Unbalanced Stereo Output
Left
R
Audio on captive screw connectors (MDA 3AV,
MDA 3SVA, MDA 3A)
0.2” (5 mm) max.
Left
L
Out connector or Outputs (1 through 3) connectors — Connect
up to three composite video devices to these BNC connectors.
On the Dual model (figure 7), the A output signals are identical
to the A input, and the B output signals are identical to the B
input.
Tip
NO GROUND HERE.
Sleeve(s)
Tip
NO GROUND HERE.
R
4
In connector or Input connector — Connect a composite video
input to this BNC connector. On the Dual model (figure 7),
Input A and Input B are completely separate inputs to two
separate distribution amplifiers.
Audio Outputs (1 through 3) connectors — Connect up to three
balanced or unbalanced audio devices to these 3.5 mm, 5-pole
captive screw connectors. Connect audio devices, such as an
audio amplifier or powered speakers. See figure 10 to properly
wire an output connector.
L
3
6
Right
Balanced Stereo Output
Do not tin the wires!
Figure 10 — Captive screw connector wiring for
audio output
CAUTION
Connect the sleeve to ground (Gnd). Connecting
the sleeve to a negative (-) terminal will damage the
audio output circuits.
Audio Input connector — Connect a balanced or unbalanced
audio input to this 3.5 mm, 5-pole captive screw connector.
Connectors are included, but you must supply the audio cable.
See figure 8 to wire a connector for the appropriate input type
and impedance level. High impedance is generally over 800 ohms.
VersaTools® MDA 3 Series • Installation
Connections and Controls
VersaTools® MDA
3 Series® •MDA
Connections
Controls
VersaTools
3 Series •and
Installation
9
VersaTools® MDA 3 Series, cont’d
7
Bal(anced)/Unbal(anced) DIP switches — For each balanced
audio output, set the associated DIP switch to the
BAL
Balanced (up) position. For each unbalanced audio
output, set the associated DIP switch to the
Unbalanced (down) position.
Smooth
A
Ridges
A
SECTION A–A
The balanced or unbalanced nature of the audio
output is determined by the output connector
wiring, not the audio input. Each output can be
balanced or unbalanced independently of the other
two outputs.
1 2 3
UNBAL
Power Supply
Output Cord
Tie Wrap
0.3” (7 mm) MAX
Audio on RCA connectors (MDA 3A RCA)
9
8
MDA 3A RCA
1
2
MDA 3A RCA,
Rear Panel
CAUTION
L
12V
.34A MAX
R
INPUT
OUTPUTS
8
9
Figure 11 — MDA 3A RCA rear panel
8
Audio Input connectors — Connect an unbalanced stereo audio
source to these L(eft) and R(ight) RCA connectors.
9
Audio Outputs (1 through 3) connectors — Connect up to three
stereo audio devices to these L(eft) and R(ight) RCA connectors.
Power (all models)
CAUTION
10
10
Power supply voltage polarity is extremely
important. Applying power with incorrect voltage
polarity could damage the power supply and the
MDA. Identify the power cord negative lead by the
ridges on the side of the cord.
Power connector — Plug the external 12 VDC power supply
into this 2-pole captive screw connector. The power supply is
included with the unit. Figure 12 shows how to wire the
connector.
CAUTION
Figure 12 — Power connector wiring
3
POWER
10
Orange Captive Screw
Connector
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply and
the MDA. Identify the power cord negative lead by
the ridges on the side of the cord (figure 12).
Installation
VersaTools® MDA 3 Series • Specifications
The length of the exposed (stripped) copper wires is
important. The ideal length is 0.3" (7 mm).
Longer bare wires can short together. Shorter wires
are not as secure in the captive screw connectors
and could be pulled out.
Use the supplied tie-wrap to strap the power cord to the
extended tail of the connector.
Your MDA may have shipped with a blue captive
screw connector. This blue connector can be plugged
into either a blue or an orange power receptacle.
The ideal length of exposed (stripped) copper wire
for the blue connector is 0.2" (5 mm).
The blue connector does not have the extended tail or the
included tie-wrap.
Do not tin the stripped power supply leads before
installing the captive screw connector. Tinned wires are
not as secure in the captive screw connectors and could
be pulled out.
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before wiring.
As an alternative, an Extron P/S 100 Universal 12 VDC Power
Supply, part #60-357-01, can power multiple MDAs or other
Extron 12 VDC devices using only one AC power connector.
® ®
VersaTools
VersaTools
MDA
MDA
3 Series
3 Series
• Specifications
• Installation
11
VersaTools® MDA 3 Series, cont’d
11
Power LED (figure 13) — When lit, this LED indicates power is
applied to the MDA.
11
Front Panel, all MDA Models
DISTRIBUTION AMPLIFIER
Figure 13 — MDA 3 Series front panel (all models)
Specifications
Video
DC offset (max. allowable) ......... 5.0 V
Input coupling .............................. AC
Video output
Number/signal type
MDA 3SV/3SVA ..............
MDA 3SV Dual ................
MDA 3V/3AV ..................
MDA 3V Dual ..................
Connectors
MDA 3SV/3SVA ..............
MDA 3SV Dual ................
MDA 3V/3AV ..................
MDA 3V Dual ..................
Nominal level ...............................
Gain ............................................... Unity
Bandwidth .................................... 100 MHz (-3 dB)
Video input
Number/signal type
MDA 3SV/3SVA
1 S-video
MDA 3SV Dual ................ 2 S-video
MDA 3V/3AV ................... 1 composite video
MDA 3V Dual .................. 2 composite video
Connectors
MDA 3SV/3SVA
(1) 4-pin mini DIN female
MDA 3SV Dual ................ (2) 4-pin mini DIN female
MDA 3V/3AV ................... 1 BNC female
MDA 3V Dual .................. 2 BNC female
Nominal level ............................... 1 Vp-p for Y of S-video and for composite
video
0.3 Vp-p for C of S-video
Minimum/maximum levels ...... 0.4 V to 2.0 Vp-p for composite video or Y
of S-video with no offset
Impedance .................................... 75 ohms
Return loss
MDA 3SV/3SVA
MDA 3SV Dual ................ <-25 dBB @ 0 to 10 MHz
All other models .............. <-27 dB @ 5 MHz
12
VersaTools® MDA 3 Series • Specifications
Installation
Minimum/maximum levels ......
Impedance ....................................
Return loss ....................................
DC offset .......................................
3 buffered S-video
2 x 3 buffered S-video
3 buffered composite video
2 x 3 buffered composite video
(3) 4-pin mini DIN female
(6) 4-pin mini DIN female
3 BNC female
6 BNC female
1 Vp-p for Y of S-video and for composite
video
0.3 Vp-p for C of S-video
0.4 V to 2.0 Vp-p, follows input
75 ohms
<-30 dB @ 5 MHz
±50 mV with input at 0 offset
Sync
Standards ...................................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio — MDA 3AV, MDA 3SVA, MDA 3A/3A RCA
Gain
DIP switch set to match output type
Unity (0 dB)
DIP switch not matched to output type
Frequency response .....................
THD + Noise ................................
S/N
MDA 3A ............................
All other models w/audio
Stereo channel separation ..........
CMRR ............................................
Output Wiring
DIP Switch
Setting
Unbalanced
Balanced
Balanced
Unbalanced
0 dB
+6 dB
-6 dB
0 dB
20 Hz to 20 kHz, ±0.05 dB
0.03% @ 1 kHz at nominal level
>90 dB, unbalanced, at maximum output
>90 dB, balanced at maximum output
>80 dB @ 1 kHz; >60 dB @ 20 kHz
>75 dB @ 20 Hz to 20 kHz
® ®
VersaTools
VersaTools
MDA
MDA
3 Series
3 Series
• Specifications
• Installation
13
VersaTools® MDA 3 Series, cont’d
Audio input — MDA 3AV, MDA 3SVA, MDA 3A/3A RCA,
MDA 5A RCA
Number/signal type
MDA 3A RCA
1 stereo unbalanced
MDA 3AV, MDA 3SVA, MDA 3A
1 stereo balanced/unbalanced
Connectors
MDA 3A RCA
2 RCA connectors
MDA 3AV, MDA 3SVA, MDA 3A
(1) 3.5 mm captive screw connector, 5 pole
Impedance
MDA 3A RCA
>10k ohms unbalanced, DC coupled
MDA 3AV, MDA 3SVA, MDA 3A
>50k ohms unbalanced, >25k ohms
balanced, DC coupled
Nominal level ............................... +4 dBu (1.23V), 0 dBu (0.775 V), -10 dBV
(316 mV), -20 dBV (100 mV) compatible
Maximum level
MDA 3A ............................ +17 dBu (unbalanced) at 1%THD+N
All other models w/audio +24 dBu (balanced) at 1%THD+N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV
2 dBu
Audio output — MDA 3AV, MDA 3SVA, MDA 3A/3A RCA
Number/signal type
MDA 3A RCA .................. 3 stereo, unbalanced
MDA 3AV, MDA 3SVA, MDA 3A
3 stereo, balanced/unbalanced
Connectors
MDA 3A RCA .................. 6 RCA connectors
MDA 3AV, MDA 3SVA, MDA 3A
(3) 3.5 mm captive screw connectors, 5
pole
Impedance
MDA 3A RCA
50 ohms unbalanced
MDA 3AV, MDA 3SVA, MDA 3A
50 ohms unbalanced, 100 ohms balanced
Gain error ...................................... ±0.1 dB channel to channel
14
VersaTools® MDA 3 Series • Specifications
Installation
Maximum level (Hi-Z)
MDA 3A ............................
All other models w/audio
Maximum level (600 ohm)
MDA 3A ............................
All other models w/audio
+15 dBV, unbalanced, at 1%THD+N
>+24 dBu, balanced at 1%THD+N
>+14 dBm, unbalanced, at 1%THD+N
>+15 dBm, balanced or unbalanced, at
1%THD+N
General
External power supply ............... 100 VAC to 240 VAC, 50/60 Hz, 5 watts,
external, autoswitchable; to 12 VDC,
1 A (max.), regulated
Power input requirements
MDA 3V/3SV ................... 12 VDC, 0.1 A (max.)
MDA 3AV/3SVA ............. 12 VDC, 0.3 A (max.)
All other models .............. 12 VDC, 0.2 A (max.)
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Rack mount ................................... Yes, with optional 1U rack shelf, part
#60-190-01, or 60-604-01;
or the VersaTools® rack shelf, part
#60-190-20, or 60-604-20
Enclosure type .............................. Metal
Enclosure dimensions ................. 1.7" H x 4.3" W x 3.0" D (1U high, quarter
rack wide)
4.2 cm H x 11.0 cm W x 7.6 cm D
(Depth excludes connectors and knobs.)
Product weight
MDA 3V, MDA 3SVA ..... 0.4 lbs (0.2 kg)
MDA 3V Dual .................. 0.7 lbs (0.3 kg)
MDA 3AV ......................... 0.6 lbs (0.3 kg)
MDA 3SV ........................... 0.4 lbs (0.2 kg)
MDA 3SV Dual, MDA 3A . 0.5 lbs (0.2 kg)
MDA 3A RCA .................. 0.4 lbs (0.2 kg)
Shipping weight
MDA 3V, MDA 3V Dual . 3 lbs (2 kg)
MDA 3AV ......................... 3 lbs (2 kg)
MDA 3SV, MDA 3SV Dual 2 lbs (1 kg)
MDA 3SVA ....................... 2 lbs (1 kg)
MDA 3A RCA ................... 2 lbs (1 kg)
® ®
VersaTools
VersaTools
MDA
MDA
3 Series
3 Series
• Specifications
• Installation
15
VersaTools® MDA 3 Series, cont’d
Vibration ....................................... ISTA 1A in carton (International Safe
Transit Association)
Listings .......................................... UL, CUL
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
All nominal levels are at ±10%.
Specifications are subject to change without notice.
16
VersaTools® MDA 3 Series • Specifications
Installation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising