Black Widow Security | BW 3150 | BW 3150 User Manual - Black Widow Vehicle Security Systems

BW 3150 User Manual - Black Widow Vehicle Security Systems
TRANSMITTER OPERATION
TRX Button
Duration
OWNER’S MANUAL
VEHICLE SECURITY
Function
1
SHORT
1
LONG (3 SEC.)
2
SHORT
System Operation
ARM
REMOTE PANIC
Button 1
Button 2
DISARM
Button 3
Button 4
3
SHORT
3
LONG (3 SEC.)
AUXILIARY 1 OUTPUT
AUXILIARY 2 OUTPUT
ARMING OPERATION
To arm the system press transmitter button 1:
• The siren will chirp once.
• The parking lights will flash once.
• The doors will lock*.
• The L.E.D. will turn solid for 10 seconds
then start flashing slowly. After 10
seconds the system is armed.
SILENT ARM/DISARM
4
SHORT
1 then 2
SHORT then SHORT
DOOR TRIGGER BYPASS
1 then 3
SHORT then SHORT
REMOTE SENSOR BYPASS
4-Button
Transmitter
* Optional feature
Standard Features:
Status indicator (red LED)
Valet / override switch
Flashing parking lights
Multi-tone siren
Dual stage impact detector
Remote panic
Remote chirp mute
Remote sensor/trigger bypass
Passive or active arming
PASSIVE ARMING
The passive arming feature allows the system to
arm automatically without user intervention.
This programmable feature may be disabled during
installation.
To arm the system passively:
1. Turn the ignition key off.
2. Exit the vehicle and close all doors.
• The LED will start flashing rapidly to
indicate that the system is preparing to
arm. The system can be armed at any
time by pressing transmitter button 1.
• The siren will chirp 30 seconds after
the last door is closed to indicate the
system is now armed.
• The doors will lock*.
Optional Features:
Starter disable
Keyless entry
Remote trunk or hatch release
Illuminated entry
Hood and trunk protection
Remote auto start
Power window roll up
Back-up battery w/charging circuit
Plug-in radar sensor
Plug-in glass break sensor
*
DISARMING OPERATION
To disarm the system press transmitter button 2.
• The siren will chirp twice.*
• The parking lights will flash twice and
remain on for 30 seconds (car locator
feature).
Note: Some features may require additional
parts and labor, and may not be appropriate for
certain vehicles. Consult your authorized dealer.
© DLC, Inc.
65-3150 Rev. 1, 03/02
4
The Passive Locking feature may be disabled during
installation.
1
Feature, press transmitter button 1 for 3
seconds:
• The siren will sound.
• The parking lights will flash.
Press button 1 to exit panic mode and rearm
the system. Press button 2 to exit panic mode
and disarm the system. The Panic Feature will
operate when the ignition is on.
• The doors will unlock.
• The dome light will turn on for 30
seconds.**
* If the alarm was triggered while away, the system will
respond with 3 chirps and 3 parking light flashes.
**
Optional feature
AUTO REARM FEATURE
The Auto Rearm feature allows the system to
automatically re-arm itself in the event the
system is disarmed and a door is not opened
within 30 seconds. This programmable feature
may be disabled during installation. The Passive
Arming feature and Auto Rearm feature are related.
In order to disable the Auto Rearm feature, the
Passive Arming feature must also be disabled during
installation.
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by using
the emergency override feature.
NOTE: This feature will not work on vehicles with
the illuminated entry feature enabled.
SILENT ARMING/DISARMING
Press transmitter button 3 to Arm or Disarm
the system silently.
CHIRP DELETE
For full time silent operation, the ARM/ DISARM
chirps can be permanently disabled. This feature
must be programmed during installation.
IGNITION LOCK
The ignition locking feature allows the doors to
automatically lock when the ignition key is
turned on, and automatically unlock when the
ignition key is turned off. This feature may be
disabled during installation.
REMOTE PANIC
In the event of an emergency (PANIC) situation,
the system’s siren can be triggered for 45
seconds to attract attention.To activate the Panic
2
CAR LOCATOR FEATURE
The Car Locator feature allows the parking
lights to stay on for 30 seconds after the alarm
is disarmed. This feature is not recommended
for vehicles with aftermarket or auxiliary
lighting. This programmable feature may be
disabled during installation.
VALET MODE
When the system is placed into the Valet Mode
the security system will be disabled.
However, the optional keyless entry and trunk
release features will still function if installed.
DOOR TRIGGER BYPASS
To intentionally arm the system with a door
open, press button 1 to arm, then within 2
seconds press button 2. The siren will chirp to
indicate the doors will not be monitored. The
Shock Sensor will still be monitored.
To exit Valet Mode:
1. Turn the ignition key on.
2. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn off.
• The Siren will chirp 2 times.
1. Turn ignition key on, off, on, off, and leave
on within 5 seconds.
LED will flicker and parking lights will flash
once.
2. Press and hold valet switch for 2 seconds.
3. LED will flicker and parking lights will flash.
The siren will give a series of chirps.
4. Release the valet switch.
5. Program all desired remotes by pressing
button 1 on each of the transmitters. The
siren will chirp after the system has
learned each remote control.
6. Turn ignition key off.
TRUNK DISARM FEATURE
The trunk disarm feature allows the alarm to
disarm automatically whenever transmitter
button 3 is used to activate the optional trunk
release. This eliminates having to first disarm
the alarm before activating the trunk release.
This feature must be programmed during
installation.
To override the system:
1. Enter the vehicle.
• Because the system is armed, the siren
will sound.
2. Turn on the ignition key.
3. Press the Valet/Service Mode switch.
• The siren will stop sounding.
To enter the Valet Mode:
1. Be sure the system is disarmed.
2. Turn the ignition key on.
3. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn on solid indicating
the system is in Valet Mode.
To enter Code Learning Mode:
OPTIONAL TRUNK RELEASE
Press button 3 for approximately 2 seconds to
open the trunk.
Remotes are now programmed to the system.
LED STATUS INDICATORS
Off= System disarmed
Slow Flashing= System armed
Rapid Flashing= Passive arming indication
Rapid Flashing (after disarm)= System
was triggered while away.
On Solid= Valet mode.
On Solid (After Active Arming)= Shock
sensor inactive for 10 seconds while settling.
On Solid (when disarmed, and not in
Valet)= Door or hood/trunk is open.
REMOTE SENSOR BYPASS
To arm the system and bypass the shock sensor,
press button 1 to arm, then within 2 seconds
press button 3. The siren will chirp to indicate
the sensor will not be monitored. The doors
and hood/trunk will still be monitored.
CHIRP INDICATIONS:
One Chirp= Armed
Two Chirps= Disarmed
Three Chirps= Disarmed, but system was
triggered while away.
Four Chirps= 30 seconds after arming,
indicates faulty sensor or trigger.
Five Rapid Chirps= Warn away triggered
ADDING/DELETING TRANSMITTERS
To add a new transmitter to the system or
delete a lost transmitter, have all desired
transmitters ready and follow the Code Learning
Mode sequence.
3
Feature, press transmitter button 1 for 3
seconds:
• The siren will sound.
• The parking lights will flash.
Press button 1 to exit panic mode and rearm
the system. Press button 2 to exit panic mode
and disarm the system. The Panic Feature will
operate when the ignition is on.
• The doors will unlock.
• The dome light will turn on for 30
seconds.**
* If the alarm was triggered while away, the system will
respond with 3 chirps and 3 parking light flashes.
**
Optional feature
AUTO REARM FEATURE
The Auto Rearm feature allows the system to
automatically re-arm itself in the event the
system is disarmed and a door is not opened
within 30 seconds. This programmable feature
may be disabled during installation. The Passive
Arming feature and Auto Rearm feature are related.
In order to disable the Auto Rearm feature, the
Passive Arming feature must also be disabled during
installation.
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by using
the emergency override feature.
NOTE: This feature will not work on vehicles with
the illuminated entry feature enabled.
SILENT ARMING/DISARMING
Press transmitter button 3 to Arm or Disarm
the system silently.
CHIRP DELETE
For full time silent operation, the ARM/ DISARM
chirps can be permanently disabled. This feature
must be programmed during installation.
IGNITION LOCK
The ignition locking feature allows the doors to
automatically lock when the ignition key is
turned on, and automatically unlock when the
ignition key is turned off. This feature may be
disabled during installation.
REMOTE PANIC
In the event of an emergency (PANIC) situation,
the system’s siren can be triggered for 45
seconds to attract attention.To activate the Panic
2
CAR LOCATOR FEATURE
The Car Locator feature allows the parking
lights to stay on for 30 seconds after the alarm
is disarmed. This feature is not recommended
for vehicles with aftermarket or auxiliary
lighting. This programmable feature may be
disabled during installation.
VALET MODE
When the system is placed into the Valet Mode
the security system will be disabled.
However, the optional keyless entry and trunk
release features will still function if installed.
DOOR TRIGGER BYPASS
To intentionally arm the system with a door
open, press button 1 to arm, then within 2
seconds press button 2. The siren will chirp to
indicate the doors will not be monitored. The
Shock Sensor will still be monitored.
To exit Valet Mode:
1. Turn the ignition key on.
2. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn off.
• The Siren will chirp 2 times.
1. Turn ignition key on, off, on, off, and leave
on within 5 seconds.
LED will flicker and parking lights will flash
once.
2. Press and hold valet switch for 2 seconds.
3. LED will flicker and parking lights will flash.
The siren will give a series of chirps.
4. Release the valet switch.
5. Program all desired remotes by pressing
button 1 on each of the transmitters. The
siren will chirp after the system has
learned each remote control.
6. Turn ignition key off.
TRUNK DISARM FEATURE
The trunk disarm feature allows the alarm to
disarm automatically whenever transmitter
button 3 is used to activate the optional trunk
release. This eliminates having to first disarm
the alarm before activating the trunk release.
This feature must be programmed during
installation.
To override the system:
1. Enter the vehicle.
• Because the system is armed, the siren
will sound.
2. Turn on the ignition key.
3. Press the Valet/Service Mode switch.
• The siren will stop sounding.
To enter the Valet Mode:
1. Be sure the system is disarmed.
2. Turn the ignition key on.
3. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn on solid indicating
the system is in Valet Mode.
To enter Code Learning Mode:
OPTIONAL TRUNK RELEASE
Press button 3 for approximately 2 seconds to
open the trunk.
Remotes are now programmed to the system.
LED STATUS INDICATORS
Off= System disarmed
Slow Flashing= System armed
Rapid Flashing= Passive arming indication
Rapid Flashing (after disarm)= System
was triggered while away.
On Solid= Valet mode.
On Solid (After Active Arming)= Shock
sensor inactive for 10 seconds while settling.
On Solid (when disarmed, and not in
Valet)= Door or hood/trunk is open.
REMOTE SENSOR BYPASS
To arm the system and bypass the shock sensor,
press button 1 to arm, then within 2 seconds
press button 3. The siren will chirp to indicate
the sensor will not be monitored. The doors
and hood/trunk will still be monitored.
CHIRP INDICATIONS:
One Chirp= Armed
Two Chirps= Disarmed
Three Chirps= Disarmed, but system was
triggered while away.
Four Chirps= 30 seconds after arming,
indicates faulty sensor or trigger.
Five Rapid Chirps= Warn away triggered
ADDING/DELETING TRANSMITTERS
To add a new transmitter to the system or
delete a lost transmitter, have all desired
transmitters ready and follow the Code Learning
Mode sequence.
3
TRANSMITTER OPERATION
TRX Button
Duration
OWNER’S MANUAL
VEHICLE SECURITY
Function
1
SHORT
1
LONG (3 SEC.)
2
SHORT
System Operation
ARM
REMOTE PANIC
Button 1
Button 2
DISARM
Button 3
Button 4
3
SHORT
3
LONG (3 SEC.)
AUXILIARY 1 OUTPUT
AUXILIARY 2 OUTPUT
ARMING OPERATION
To arm the system press transmitter button 1:
• The siren will chirp once.
• The parking lights will flash once.
• The doors will lock*.
• The L.E.D. will turn solid for 10 seconds
then start flashing slowly. After 10
seconds the system is armed.
SILENT ARM/DISARM
4
SHORT
1 then 2
SHORT then SHORT
DOOR TRIGGER BYPASS
1 then 3
SHORT then SHORT
REMOTE SENSOR BYPASS
4-Button
Transmitter
* Optional feature
Standard Features:
Status indicator (red LED)
Valet / override switch
Flashing parking lights
Multi-tone siren
Dual stage impact detector
Remote panic
Remote chirp mute
Remote sensor/trigger bypass
Passive or active arming
PASSIVE ARMING
The passive arming feature allows the system to
arm automatically without user intervention.
This programmable feature may be disabled during
installation.
To arm the system passively:
1. Turn the ignition key off.
2. Exit the vehicle and close all doors.
• The LED will start flashing rapidly to
indicate that the system is preparing to
arm. The system can be armed at any
time by pressing transmitter button 1.
• The siren will chirp 30 seconds after
the last door is closed to indicate the
system is now armed.
• The doors will lock*.
Optional Features:
Starter disable
Keyless entry
Remote trunk or hatch release
Illuminated entry
Hood and trunk protection
Remote auto start
Power window roll up
Back-up battery w/charging circuit
Plug-in radar sensor
Plug-in glass break sensor
*
DISARMING OPERATION
To disarm the system press transmitter button 2.
• The siren will chirp twice.*
• The parking lights will flash twice and
remain on for 30 seconds (car locator
feature).
Note: Some features may require additional
parts and labor, and may not be appropriate for
certain vehicles. Consult your authorized dealer.
© DLC, Inc.
65-3150 Rev. 1, 03/02
4
The Passive Locking feature may be disabled during
installation.
1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising