Sears | 8080 | User manual | Sears 8080 User manual

Sears 8080 User manual
INSTALLING THE BATTERIES
Your A/V Producer requires four (4) new AAA
alkaline batteries. To install the batteries:
URC 8080
A/V Producer
1
On the back of the A/V
Producer, push down on
the tab and slide the
battery cover off.
2
Match the + and - marks
on the batteries to the +
and - marks in the battery
case, then insert the
batteries.
3
Slide the battery cover
back into place.
User Manual
4
POWER
Test the unit by pressing
POWER. If the batteries
are inserted correctly, the
red light will blink.
Note: After inserting the batteries, the LCD screen will
enter a test mode which tests each segment of the
LCD screen. This process will last for 10 seconds or
until any key is pressed, which ever occurs first.
USING YOUR A/V PRODUCER
Feature
Function
The MAGIC key is used to access
the menu and program your
A/V Producer.
MAGIC
Features and Functions
The illustration below and the chart on the next two
pages describe the features and the functions of the
A/V Producer’s keypad. The following keys will
always have the same function, regardless of which
component you are controlling. For an explanation
of what each key does by component type, please
use the index at the rear of the manual (pages 45-57).
TV
VCR
CBL
SAT
AMP
TUN
CD
AUX1
HOME THEATER
AMP
TUN
TV
CD
VCR
SAT
CBL
ESC
W
PO
MENU+
ER
LITE
C
ES
SUR
R
REA
R
TE
N
CE
MENU-
G
PRO
NU
ME
AR
CLE
CT
LE
E
S
L+
VO
LVO
P
EE
SL
TE
MU
+
CH
CH
DI
SP
PR
FR
EV
Z
EE
CH
AUD
SLOWREW
EJECT
REC
TV/SAT
AP
SW
VID
VIE
MOPIP
POWER
VOL-
VOL+
SLOW SLOW+
PL
STOP
FF
LIT
E
X2
PAU
The ESC (Escape) key is used to
exit the LCD Screen menu.
The LITE key is used to turn ON
and OFF the A/V Producer’s
backlit keypad and LCD screen.
Press the LITE key once to turn
ON the backlight. The A/V
Producer’s backlight will stay on for
10 seconds after the last key press
and re-activates with the press of a
key. To de-activate the backlight,
press the LITE key again.
E
PIP
ENTER
The HOME THEATER key is used
to select the Home Theater mode of
the A/V Producer.
AUX1
HOME THEATER
IFT
SH
The TV, VCR, CBL, SAT, AMP, TUN,
CD, and AUX1 keys are used to
select the home entertainment
component you want to control. If
your component does not respond
when you press a key on the
remote control, press either the TV,
VCR, CBL, SAT, AMP, TUN, CD,
and AUX1 key to tell the remote
control which component you would
like to operate.
C
GI
MA
MUTE
The POWER key controls power ON
and OFF.
The VOL + (Volume Up), VOL(Volume Down) and MUTE keys
control the volume the same as the
Volume Up and Down and Mute
keys on your original remote.
Feature
CH-
CH+
AUD
VID
SHIFT
Function (Cont.)
The CH + (Channel Up) and CH(Channel Down) keys change
channels the same as the Channel
Up and Down keys on your
original remote.
The AUD and VID macro keys
memorize up to 15 keystrokes that
can be accessed in sequence at the
press of a single key. These
keys are not mode specific.
The SHIFT key accesses advanced
features that are mapped under
the following keys: CENTER, MENU,
SELECT, MUTE, PREV CH,
PIP, REW, PLAY, FF, STOP and
PAUSE.
Important: For a detailed explanation of what function
each key will perform by device type (TV, VCR, CBL,
etc.), please refer to pages 45 through 57.
SETTING THE CLOCK
To set up the CLOCK/TIME on the display screen:
1
MAGIC
2
MENU-
SELECT
3
MENU-
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
x 2 Press the MENU - key twice, the
display will change to [CONFIGURE].
Press SELECT, the display will
change to [THEATR SEL].
Press MENU - one time, the display
will change to [TIME SET]. Press
SELECT again.
SELECT
4
0-9
5
MENU-
SELECT
6
MENU-
SELECT
The display will change to [TIME]
and the first digit in the time will
blink. Enter either a 0 or a 1, then
the next digit in the time will begin to
blink, continue entering the time
until all four digits of the time have
been set.
After the time has been set, AM/PM
will then blink. Press MENU - to
toggle between AM and PM, once
AM or PM is selected, press
SELECT.
The display will then change to the
day of the week (MON, TUES, WED,
THURS, FRI, SAT or SUN). Use
MENU - to toggle through the days
until the proper day of the week is
displayed on the screen, then press
SELECT. The display will return to
the [DEVICE and the TIME] screen
with the correct time on the display.
NOTE: After changing the batteries, you will have to reprogram
the clock.
QUICK SET UP
7
To Quickly Set Up the A/V Producer to Operate
Your Home Entertainment Components
1
2
3
Turn on all of the components that
you will be setting up.
TV
MAGIC
4
MENUSELECT
5
SELECT
POWER
VCR
6
SELECT
POWER
CBL
ESC
Continue to enter your codes as
illustrated in Steps 5 and 6 until the
A/V Producer is operating all of your
home entertainment components.
Once you have finished setting up
your components, press ESC to
return to the [DEVICE and TIME]
display.
Press and release the TV key.
Press and hold MAGIC until the
display screen changes from
[TV and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SETUP]. Press SELECT. The
display will change to [TV}.].
Enter the first TV code listed for your
brand in the “Set Up Codes for TVs”
on pages 10-12, then press
SELECT. Point the remote control at
the TV and press POWER. Your
Television should turn OFF. If your TV
does not turn OFF, enter the next
code in the code list then press
SELECT followed by POWER again.
Once your TV turns OFF, press VCR.
You will now enter your VCR code.
Enter the first VCR code listed for
your brand in the “Set Up Codes for
VCRs” on pages 13-14, then press
SELECT. Point the remote control
at the VCR and press POWER. Your
VCR should turn OFF. If your VCR
does not turn OFF, enter the next
code in the code list then press
SELECT followed by POWER again.
Once your VCR turns OFF, press
CBL. You will now enter your Cable
Box code.
If you would like to setup each of your
components individually, or if you purchase a
component after you have set up the A/V
Producer, see the "SETTING UP INDIVIDUAL
HOME ENTERTAINMENT COMPONENTS"
section on pages 10 - 22 in this manual.
Set Up Codes for TVs ....................... Pages 10 - 12
Set Up Codes for VCRs .................... Pages 13 - 14
Set Up Codes for Cable Boxes .................. Page 16
Set Up Codes for DSS and
Satellite Receivers ............................... Page 17
Set Up Codes for Laser Disc Players ......... Page 18
Set Up Codes for CD Players .................... Page 19
Set Up Codes for Tuner Receivers ............ Page 21
Set Up Codes for Amplifiers ....................... Page 22
SETTING UP INDIVIDUAL HOME
ENTERTAINMENT COMPONENTS
Set Up Codes for TVs (cont.)
Broksonic
Candle
To Set Up Your Television
1
Turn on your TV.
2
TV
3
MAGIC
4
MENUSELECT
5
6
Carnivale
Carver
CCE
Celebrity
Citizen
SELECT
SELECT
POWER
ESC
Press and release the TV key.
Press and hold MAGIC until the
display screen changes from
[TV and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press SELECT and the display
screen will change to [TV].
Enter the first TV code listed for your
brand in the “Set Up Codes for TVs”
on pages 10-12, then press SELECT.
Point the remote control at the TV
and press POWER. Your Television
should turn OFF. If your TV turns
OFF, press the ESC key to return the
display to [TV and the TIME]. If your
TV does not turn OFF, enter the next
code in the code list then press
SELECT followed by POWER again.
Once the correct code is entered,
press the ESC key to return the
display to [TV and the TIME].
For a detailed explanation of what function each key
will perform in the TV mode, please refer to page 45
in the index.
Set Up Codes for TVs
A-Mark
Abex
Admiral
Adventura
Aiko
Akai
Alleron
Ambassador
Anam
003
032
093, 016, 180,
165, 179
046
092
030, 056, 145,
151
179, 183
177
180
Anam National
AOC
Archer
Audiovox
Belcor
Bell & Howell
Bradford
Brockwood
055
030, 019, 185,
080, 056, 003,
052
003
180, 003
019, 030
016, 154, 179,
180
180
019
Clairtone
Concerto
Contec
Craig
Crown
Curtis Mathes
CXC
Daewoo
Daytron
Dumont
Dynatech
Electroband
Electrohome
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
Gibralter
Goldstar
Grunpy
Hallmark
Harvard
Hitachi
Infinity
Janeil
JBL
JCB
JVC
Kawasho
Kaypani
KEC
Kenwood
Kloss
KMC
KTV
Logik
Luxman
LXI
236, 463, 180,
003
030, 056, 186,
046
030
054 , 187, 170
217
000
092, 060, 030,
056, 280, 186,
046, 039
185
056
180, 185, 157,
158
180
180, 039
047, 060, 054,
154, 030, 039
180
451, 092, 019,
039, 091
056, 092
017, 019
046
000, 185
381, 389, 409
463, 236, 180,
177, 179, 280,
178, 282, 154,
019, 185, 038,
039, 158, 181,
182, 183, 270
030
154, 159
179
171, 179, 180
180
047, 451, 051,
021, 027, 282,
055, 178, 029,
135, 174, 279
017, 019, 030
056, 019, 030,
178, 001, 002,
032
179, 180
178, 179, 236,
019
180, 236, 178,
179
145, 151, 056,
032, 038, 279,
409, 413
054
046
054
000
053, 036, 182,
169, 069, 160
158
052
180, 060
019, 030
030, 046, 024
106
030, 039, 180,
183, 185, 217,
280
016, 180, 236
056
047, 054, 148,
154, 156, 178
Magnasonic
Magnavox
Majestic
Marantz
Matsushita
Megatron
MEI
Memorex
MGA
Midland
Minutz
Mitsubishi
Motorola
MTC
Multitech
NAD
NEC
Nikko
Noblex
Noshi
NTC
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
Philco
Philips
Pilot
Pioneer
Portland
Prism
Proscan
Proton
Pulsar
Quasar
RadioShack
RCA
054, 156, 179,
092, 030, 093,
019, 003
054, 096, 186,
030, 187, 020,
024, 028, 036,
386
016, 017
030, 054, 096,
187
250
003, 145, 178
185, 051
016, 056, 106,
150, 154, 178
150, 155, 178,
030, 019, 093
017, 032, 039,
047, 051, 135
021
150, 155, 178,
030, 019, 093,
241
093, 055, 054,
150, 051
060, 056, 030,
019, 185, 091
180, 217, 019
156, 166, 178,
019
019, 030, 036,
056
030, 092, 178
430
018
092
180
154, 166, 250,
463, 180, 179,
150, 165
093, 165
236, 463, 180,
179
250, 051, 055,
054
047, 051, 060,
019, 018, 030,
156, 021, 027,
178, 003, 135,
039, 002, 032,
149
054, 096, 030,
019, 187, 020,
028
054, 096, 030,
019, 187, 020,
028
019, 030, 039
166, 038
092, 019, 039
051, 055
047
003, 052, 178
092, 017, 019
250, 051, 055,
165
019, 030, 032,
039, 047, 056,
154, 165, 178,
180, 409
047, 018, 019,
029, 038, 090,
135, 147, 278,
093
6
Set Up Codes for TVs (cont.)
Realistic
Rhapsody
Runco
Sampo
Samsung
Samsux
Sanyo
Scimitsu
Scotch
Scott
Sears
Sharp
Shogun
Signature 2000
Simpson
Sony
Soundesign
Spectricon
Squareview
SSS
Starlite
Supre-Macy
Supreme
019, 030, 032,
039, 056, 154,
165, 178, 180
183, 185
017, 030
030, 032, 039,
052
060, 019, 030,
032, 056, 178,
427, 482
039
154, 159, 146
019
178
019, 178, 179,
180, 236
047, 054, 056,
146, 148, 149,
154, 156, 159,
171, 178, 179
093, 039, 153,
157, 165, 386
019
016, 047, 054,
019
186, 187, 030
000, 080
178, 179, 180,
186
003, 180, 030,
019, 056
171
019, 180, 236
180, 236, 019
046, 186
000
Sylvania
Symphonic
Tandy
Tatung
Technics
Technol Ace
Techwood
Teknika
TMK
Toshiba
Tosonic
Totevision
Trical
Universal
Vector Research
Victor
Vidikron
Vidtech
Viking
Wards
Zenith
Zonda
054, 096, 030,
187, 186, 020,
028
171, 179, 180
093, 165, 054,
047, 039
055, 051, 003
051, 250, 055
179
003, 051, 056
092, 054, 060,
056, 019, 015,
180, 179, 186,
150, 039, 312
056, 177, 178,
236
156, 154, 060,
036, 149
185
039
157
027, 021, 047
030
053
054, 242
019, 036, 178
046
154, 016, 096,
030, 056, 165,
019, 021, 027,
020, 178, 179,
080, 174, 028,
029
017, 092, 016
003
To Set Up Your VCR or TV/VCR Combinations
1
2
3
SELECT
POWER
or
PL
ESC
For a detailed explanation of what function each key
will perform in the VCR mode, please refer to page
47 in the index.
Set Up Codes For VCRs
Admiral
Adventura
Aiko
Aiwa
Akai
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
Turn on your VCR and insert a tape.
VCR
MAGIC
Press and release the VCR key.
Press and hold MAGIC until the
display screen changes from
[VCR and the TIME] to [TIMED SEQ].
Calix
Candle
Canon
Capehart
Carver
CCE
Citizen
Colt
Craig
Curtis Mathes
4
MENUSELECT
5
SELECT
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Enter the first VCR code listed for
your brand in the “Set Up Codes for
VCRs” on pages 13-14, then press
SELECT. Point the remote control at
the VCR and press POWER or PLAY.
Your VCR should turn OFF or start to
play. If your VCR turns OFF or starts
to play, press the ESC key to return
the display to [VCR and the TIME]. If
your VCR does not turn OFF or start
to play, enter the next code in the
code list then press SELECT followed
by POWER or PLAY again. Once the
correct code is entered, press the
ESC key to return the display to [VCR
and the TIME].
Cybernex
Daewoo
Daytron
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Press SELECT and the display
screen will change to [VCR].
Fisher
Fuji
Funai
Garrard
048
000
278
000
041, 049, 053,
061, 106
035, 081
240
037, 038
240
104, 048, 046
184, 209, 121,
211, 295, 361,
002, 479
037
037, 038
035
020
081
072, 278
037, 278, 240,
035, 000
072
037, 047, 072,
240, 271
035, 041, 060,
202
051, 240
020, 045, 278,
046
020, 278
000
037, 240, 043
037
032
184, 209, 479,
000, 002, 036,
037, 043, 061,
068, 121, 208,
211, 212, 278,
294, 295, 361
047, 054, 066,
104, 046
033, 035, 032,
034
000, 278, 072,
240
000
GE
Go Video
Goldstar
Gradiente
Harley Davidson
Harman/Kardon
Harwood
Havard
Headquarter
HI-Q
Hitachi
Jensen
JVC
KEC
Kenwood
KLH
Kodak
Lloyds
Logik
LXI
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
MEI
Memorex
MGA
MGN Technology
Minolta
Mitsubishi
035, 060, 065,
202, 048
232, 279, 240,
526
037, 038, 278
000
000
038, 075
068, 072
072
046
047
042, 000, 041,
065, 105, 166,
396
041, 008, 067
008, 041, 067,
206
037, 278
038, 041, 067,
008
072
035, 037
208, 072, 038
072
037, 035, 042,
046, 047, 054,
066, 104, 105
240, 037, 278,
020, 072
035, 039, 081,
110, 149
240
035, 081
037
035, 162, 454,
081, 110
035
000, 035, 037,
039, 046, 047,
048, 104, 240
043, 061
240
042, 105
043, 061, 067,
075, 173, 008,
048
Set Up Codes For VCRs (Cont.)
Motorola
MTC
Multitech
NAD
NEC
Nikko
Nikon
Noblex
Olympus
Optimus
Optonica
Orion
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Portland
Protec
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radix
Randex
RCA
Realistic
Ricoh
035, 048
000, 240
000, 072
104
038, 040, 041,
067, 104, 008
037
034
240
035
037, 048, 104,
162, 454
062
184, 209, 000,
479, 002, 036,
037, 043, 061,
068, 121, 028,
211, 212, 278,
294, 295, 361
035, 162, 254,
378, 454
035, 037, 038,
040, 042, 054,
240
042, 065, 105
035, 081, 110
035, 062, 081,
110
037
067, 008
020
072
039, 051, 240,
278
046
046
035, 162, 454
000, 037, 035,
048
037
037
060, 202, 042,
149, 048, 065,
105, 106, 035
000, 035, 037,
046, 047, 048,
062, 066, 104,
240
034, 035
Runco
Salora
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Shogun
Singer
Sony
STS
Sylvania
Symphonic
Tatung
TEAC
Technics
Teknika
TMK
Toshiba
Totevision
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Wards
XR-1000
Yamaha
Zenith
To Set Up Your Cable Box:
039
075
240, 045, 051,
053
039, 048
041, 067, 271,
209, 072, 002,
479, 008
104, 046, 047,
054, 240
043, 045, 121,
184, 210, 211,
212
035, 037, 042,
046, 047, 054,
066, 104, 105,
000
048, 062
072, 000, 240
051, 240
072, 037, 240
032, 033, 034,
035
042
000, 035, 043,
081, 110
000
041, 067, 000
000, 041
035, 162, 454
000, 035, 037
036, 208, 240
043, 045, 060,
066, 210, 212,
366
037, 240
240
045
038, 040
040, 045, 061
240, 000, 072
000, 035, 042,
047, 048, 060,
062, 072, 149,
212, 240, 202
000, 035, 072,
240
038
039, 033, 034,
000
Set Up Codes for TV/VCR Combinations
American High
Broksonic
Colt
Curtis Mathes
Daewoo
Emerson
Funai
GE
Harley Davidson
Hitachi
HQ
Lloyd's
Magnavox
Magnin
035*
002, 294, 479
072
035*
278
002, 294, 479
000
035*, 060*,
048*, 240
000
035*, 000
000
000
000, 035*, 081*
240
Memorex
MGA
Mitsubishi
Orion
Panasonic
Penney
Quasar
RCA
Sansui
Sanyo
Sears
Sony
Symphonic
Zenith
037, 162*
240
048*
002, 294, 479
035*, 162*
035*, 240, 162*
035*, 162*
060*, 035*,
048*
000, 479
240
000, 037
032
000
000, 037
Note*:
TV/VCRs working on 032 will need TV code 000 for volume control.
TV/VCRs working on 035 will need TV code 051 for volume control.
TV/VCRs working on 048 will need TV code 093 for volume control.
TV/VCRs working on 060 will need TV code 047 for volume control.
TV/VCRs working on 081 will need TV code 054 for volume control.
TV/VCRs working on 162 will need TV code 250 for volume control.
TV/VCRs working on 294 will need TV code 236 for volume control.
1
2
3
Turn on your Cable Box.
CBL
MAGIC
4
MENUSELECT
5
6
SELECT
SELECT
POWER
ESC
Press and release the CBL key.
Press and hold MAGIC until the
display screen changes from
[CBL and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press SELECT and the display
screen will change to [CBL].
Enter the first Cable Box code listed
for your brand in the “Set Up Codes
for Cable Boxes” on page 16, then
press SELECT. Point the remote
control at the Cable Box and press
POWER. Your Cable Box should
turn OFF. If your Cable Box turns
OFF, press the ESC key to return
the display to [CBL and the TIME]. If
your Cable Box does not turn OFF,
enter the next code in the code list
then press SELECT followed by
POWER again. Once the correct
code is entered, press the ESC key
to return the display to
[CBL and the TIME].
Note: If your original Scientific Atlanta remote control
does not have an “ON” key, press CH+ or one of the
digit keys on the A/V Producer to turn your Cable
Box on.
For a detailed explanation of what function each key
will perform in the Cable mode, please refer to page
45 in the index.
5
Set Up Codes For Cable Boxes
ABC
Allegro
Antronix
Archer
Cabletenna
Cableview
Century
Citizen
Colour Voice
Comband
Comtronics Eagle
Contec
Eastern
Everquest
Focus
Garrard
GC Electronics
GE
Gemini
General Instrument
Goldstar
Hamlin
Hitachi
Hytex
Infinity
Jasco
Jerrold
Macom
Magnavox
Memorex
Movie Time
Novaplex
Novavision
NSC
Oak
Omega
Panasonic
Panther
Paragon
003, 014, 007,
008, 011, 017,
001, 013
153, 000, 315,
191
022, 207
022, 153, 207,
797
022
022
153
153, 315
025, 031
232, 233
040, 060, 008
019
002
015, 040
400
153
207
232, 233
015, 057, 242
476, 276, 003,
014, 011
040, 144
009, 020, 034,
259, 273
011
007
770
153, 315
003, 014, 476,
012, 011, 015,
024, 276
033
027, 334
000
063, 156
618
008, 017, 477
063, 156
007, 019
015
000, 021, 107
637
000
Philips
Pioneer
Popular Mechanics
Prelude
Pulsar
RadioShack
RCA
Realistic
Recoton
Regal
Regency
Rembrandt
Runco
Samsung
Scientific Atlanta
Signal
Signature
SL Marx
Sprucer
Starcom
Stargate
Starquest
Starsight
Sylvania
Tandy
TeleCaption
Teleview
Texscan
Timeless
Tocom
Toshiba
Tusa
TV86
Unika
United Artists
United Cable
Universal
Videoway
Viewstar
Zenith
Zentek
025, 027, 031,
153, 242, 290,
334
533, 144, 023,
260
400
770
000
797
021
207
400
020, 259, 273,
279
002
011, 153
000
040, 144
008, 477, 017,
006
015, 040
011
040
021, 307
003, 015
015, 040, 770
015
542
001
258
221
040, 063
001
418
012, 013
000
015
063, 040
022, 153, 207
007
003
022, 077, 153,
191, 207
250
027, 060, 063,
211, 258
000, 525
400
To Set Up Your DSS or Satellite Receiver
1
2
3
Turn on your DSS or Satellite
Receiver.
SAT
MAGIC
4
MENU-
SELECT
Press and release the SAT key.
Press and hold MAGIC until the
display screen changes from
[SAT and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
6
SELECT
SELECT
POWER
ESC
Press SELECT and the display
screen will change to [SAT].
Enter the first Satellite code listed
for your brand in the “Set Up Codes
for Satellites” on page 17, then
press SELECT. Point the remote
control at the Satellite and press
POWER. Your Satellite should turn
OFF. If your Satellite turns OFF,
press the ESC key to return the
display to [SAT and the TIME]. If
your Satellite does not turn OFF,
enter the next code in the code list
then press SELECT followed by
POWER again. Once the correct
code is entered, press the ESC key
to return the display to
[SAT and the TIME].
For a detailed explanation of what function each key
will perform in the Satellite mode, please refer to
page 55 in the index.
Set Up Codes for DSS and Satellite Receivers
AlphaStar DSS
Amplica
Amway
Astro Industries
BSR
Cable Innovations
Capetronic
Century
Channel Master
Chaparral
Citoh
Conifer
Curtis Mathes
Drake
772
072
043, 075
095
095
554, 555
095
538
018, 212
053, 209, 216
164
004
061, 072
018, 064, 149,
245
DX Antenna
041
Echostar
148, 159, 269,
280
Echostar DSS
775
General Instrument 050, 361, 554,
555
Hitachi DSS
819, 749
Homecable
238
HTS DSS
775
Hughes DSS
749, 819
Hytek
095
Intersat
043
IQ
210
Janeil
152
Jerrold Primestar
627
Jerrold
Legend
Macom
Magnavox DSS
Memorex
Norsat
Panasonic
Panasonic DSS
Pansat
Philips
Philips DSS
Pico
Primestar DSS
Prosat
RadioShack
Ramsey
RCA DSS
Realistic
Sony DSS
Star Trak
Strong
STS
Toshiba
Toshiba DSS
Uniden
Uniden DSS
Zenith
361
269
018, 050, 061
724, 722
269
004
152
701
647
200
724, 722
075
627
158
554
075
566
051, 052
639
180, 421, 547
421
041, 210
061, 082
790
052, 074, 076,
238, 296, 370,
554, 555
724, 722
061, 064
To Set Up Your Laser Disc Player:
To Set Up Your CD Player:
1
Turn on your Laser Disc Player and
insert a disc.
1
Press and release the AUX 1 key.
2
Press and hold MAGIC until the
display screen changes from
[LDP and the TIME] to [TIMED SEQ].
3
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
4
Press SELECT and the display
screen will change to [LDP].
5
Enter the first Laser Disc code listed
for your brand in the “Set Up Codes
for Laser Disc Players” on page 16,
then press SELECT. Point the
remote control at the Laser Disc
Player and press POWER or PLAY.
Your Laser Disc Player should turn
OFF or play your disc. If your Laser
Disc Player turns OFF or plays your
disc, press the ESC key to return the
display to [LDP and the TIME]. If
your Laser Disc Player does not
turn OFF or play your disc, enter the
next code in the code list then press
SELECT followed by POWER or
PLAY again. Once the correct code
is entered, press the ESC key to
return the display to
[LDP and the TIME].
6
2
3
AUX1
MAGIC
4
MENUSELECT
5
6
SELECT
SELECT
POWER
or
PL
ESC
For a detailed explanation of what function each key
will perform in the AUX1 mode, please refer to page
50 in this index.
Set Up Codes for Laser Disc Players
Aiwa
Carver
Denon
Disco Vision
Funai
Hitachi
Magnavox
Marantz
Mitsubishi
NAD
NEC
203
064, 194, 323
172, 241
023
203
023
194, 217, 241
064, 194
059
059
286
Panasonic
Philips
Pioneer
Quasar
RCA
Realistic
Samsung
Sega
Sony
Theta Digital
Yamaha
204
064, 194
059, 023
204
128, 351
203
323
023
193, 201, 270
194
217
Turn on your CD Player and insert a
disc.
CD
MAGIC
MENUSELECT
SELECT
SELECT
PL
ESC
Press and release the CD key.
Press and hold MAGIC until the
display screen changes from
[CD and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press SELECT and the display
screen will change to [CD].
Enter the first CD code listed for
your brand in the “Set Up Codes for
CD Players” on pages 19-20, then
press SELECT. Point the remote
control at the CD Player and press
PLAY. Your CD Player should start
to play your disc. If your CD Player
plays your disc, press the ESC key
to return the display to [CD and the
TIME]. If your CD Player does not
play your disc, enter the next code in
the code list then press SELECT
followed by PLAY again. Once the
correct code is entered, press the
ESC key to return the display to
[CD and the TIME].
For a detailed explanation of what function each key
will perform in the CD mode, please refer to page 56
in the index.
Set Up Codes for CD Player
Acoustic Research
ADC
Adcom
Aiwa
Akai
Alpine
Audio Alchemy
Audio-Technica
BSR
Burmester
California Audio Lab
Capetronic
Carrera
Carver
Craig
123
018, 033
155, 234
012, 124, 157
156, 676
341
194
170
194, 245
420
029
237
194
157, 179, 299,
365, 437
615
Crown
DAK
Denon
DKK
Emerson
Fisher
Garrard
GE
Genexxa
Goldstar
Gradiente
Harman/Kardon
Hitachi
122
245
003, 034
000
155, 164, 305,
469
048, 088, 174,
179, 342
245, 280, 393,
420, 425, 633
009, 334
032, 164, 305
030, 417, 525
558
108, 426
032, 139, 155
6
Set Up Codes for CD Player (Cont.)
Inkel
JVC
Kenwood
Kodak
Koss
Krell
Kyocera
Luxman
LXI
Magnavox
Marantz
McIntosh
MCS
MGA
Mission
Mitsubishi
MTC
NAD
Nakamichi
NEC
Nikko
NSM
Onkyo
Optimus
Panasonic
Parasound
Philco
Philips
Pioneer
065
072, 655, 658
028, 037, 048,
190, 337, 338,
339, 340, 523
287
734
157
018
093, 149, 327
305
038, 129, 157,
526
005, 029, 038,
157, 180, 435
287
029, 043, 345,
454
083
157
083, 098
420
019, 299
147
043, 130, 234
164, 169, 170,
174, 525
157
101, 102, 138,
381
000, 032, 037,
087, 175, 179,
194, 196, 280,
305, 342, 420,
426, 437, 468,
536
029, 367, 388,
752
194
603, 734
157, 274, 287
032, 244, 305,
468, 551
Proton
QED
Quasar
RCA
Realistic
Rotel
SAE
Samsung
Sansui
Sanyo
Schneider
Scott
Sears
Sharp
Sherwood
Shure
Signature
Signature 2000
Sony
Soundesign
STS
Symphonic
Tascam
TEAC
Technics
Toshiba
Vector Research
Victor
Wards
Yamaha
Yorx
Zenith
152, 157
157
029
009, 053, 155,
179, 305, 764
155, 164, 175,
179, 180, 237,
420
157, 420
157
524
157, 202, 216,
305
087, 179
560
155, 164, 305
305
037, 180, 262,
265
065, 114, 180,
196, 426
043
108
108
000, 185, 490,
604, 605, 727
145, 425
018
183
420
016, 045, 153,
174, 180, 183,
378, 393, 420
029, 207, 303
019, 299
033, 194, 417
072
108
036, 170, 187,
261
461
615
To Set Up Your Tuner/Receiver
1
2
3
Turn on your Tuner/Receiver.
TUN
MAGIC
4
MENUSELECT
5
SELECT
Press and release the TUN key.
Press and hold MAGIC until the
display screen changes from
[TUN and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press SELECT and the display
screen will change to [TUNER].
SELECT
POWER
ESC
Enter the first Tuner code listed for
your brand in the “Set Up Codes for
Tuner/Receivers” on page 21, then
press SELECT. Point the remote
control at the Tuner/Receiver and
press POWER. Your Tuner/Receiver
should turn OFF. If your Tuner/
Receiver turns OFF, press the ESC
key to return the display to
[TUN and the TIME]. If your Tuner/
Receiver does not turn OFF, enter
the next code in the code list then
press SELECT followed by POWER
again. Once the correct code is
entered, press the ESC key to return
the display to [TUN and the TIME].
For a detailed explanation of what function each key
will perform in the Tuner mode, please refer to page
54 in the index.
Set Up Codes for Tuner/Receivers
ADC
Adcom
Admiral
Aiwa
Akai
Bose
Capetronic
Carver
Casio
Clarinette
Curtis Mathes
Denon
Emerson
Fisher
Garrard
Goldstar
Harman/Kardon
Hitachi
Inkel
JVC
Kenwood
Koss
Lloyd
Luxman
LXI
Magnavox
Marantz
MCS
Modulaire
NAD
Nakamichi
531
616
182
121, 125, 158,
189, 405
076, 224
639
531
008, 042, 189,
360, 412
195, 201
195
201
004, 273, 771,
386
255, 424
042, 219, 360
281, 424, 440,
463
281, 386
110
386
062
074, 464
027, 077, 186,
313, 314
255, 424
195
166
181
128, 189, 195,
531
189, 006, 039,
128, 200, 412
039, 201, 346
195
320
347
NEC
Onkyo
Optimus
Panasonic
Penney
Philips
Pioneer
Quasar
RCA
Realistic
Sansui
Sanyo
Scott
Sears
Sharp
Sherwood
Sonic
Sony
Soundesign
Symphonic
TEAC
Technics
Techwood
Victor
Wards
Yamaha
Yorx
Zenith
235
135, 100, 119,
380
080, 177, 181,
186, 219, 440,
531, 670
039, 518, 309
195, 201
189, 412
014, 080, 150,
289, 531, 630
039
054, 346, 360,
530, 531
163, 181, 182,
195
189, 346
219
105, 163, 322,
390
201
186
062, 491, 502
281
158, 238
670
182
463, 163, 298,
387
039, 208, 309,
518
281
074
014, 042, 054,
080, 158, 189
176, 081, 082,
186
195
281
SETTING UP ADDITIONAL HOME
ENTERTAINMENT COMPONENTS
To Set Up Your Amplifier
1
Turn on your amplifier.
2
Press and release the AMP key.
3
AMP
MAGIC
4
MENUSELECT
5
6
SELECT
SELECT
POWER
ESC
Press and hold MAGIC until the
display screen changes from
[AMP and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press SELECT and the display
screen will change to [AMP].
Enter the first Amplifier code listed
for your brand in the “Set Up Codes
for Amplifiers” on page 22, then
press SELECT. Point the remote
control at the Amplifier and press
POWER. Your Amplifier should turn
OFF. If your Amplifier turns OFF,
press the ESC key to return the
display to [AMP and the TIME]. If
your Amplifier does not turn OFF,
enter the next code in the code list
then press SELECT followed by
POWER again. Once the correct
code is entered, press the ESC key
to return the display to
[AMP and the TIME].
Besides the device keys that are already labeled
(TV, VCR, CBL, etc.), the A/V Producer can also
operate the following components: DVD Players,
Cassette Decks, Home Automation, Digital Audio
Tape, Phonographs, Video Accessories and
Miscellaneous Audio Components (Graphic
Equalizers and Digital Music Service Boxes).
The Set Up codes for these devices can be
accessed under the following device keys:
DVD Players:
Cassette Decks:
Home Automation:
Digital Audio Tape:
Phonographs:
Video Accessories:
Miscellaneous Audio:
Note: Each device key (TV, VCR, CBL etc.) can
only operate one component at a time. If you have
already set up a component on a key, then assigning
a second component on the same key will erase the
code for the first component you set up. For
example, if you set up a Laser Disc Player on AUX1
and then set up a DVD Player on AUX1, the A/V
Producer will only operate the DVD Player.
For example, to set up a DVD Player on the AUX1 key:
1
For a detailed explanation of what function each key
will perform in the Amplifier mode, please refer to
page 55 in the index.
2
Set Up Codes for Audio Amplifiers
3
Accuphase
Acurus
AudioSource
Carver
Denon
Elan
Forte
GE
Goldstar
Harman/Kardon
JVC
Kenwood
Luxman
Magnavox
Marantz
McIntosh
382
765
011
269
160
647
606
078
031
106
331
356
165
269
269, 321
251
Nakamichi
NEC
Optimus
Panasonic
Philips
Pioneer
Realistic
Sansui
Shure
Sony
Soundesign
Technics
Victor
Wards
Yamaha
Turn on your DVD Player and insert
a disc.
AUX1
MAGIC
321
264
013, 300, 395
308
269
013, 300
395
321
264
220, 689
078, 211
308
331
013, 078, 211
133, 143, 354,
504
Use the AUX1 Key
Use the AUX1 Key
Use the CD Key
Use the AUX1 Key
Use the CD Key
Use the CBL Key
Use the AMP Key
4
MENUSELECT
5
SELECT
Press and release the AUX1 key.
Press and hold MAGIC until the
display screen changes from
[LDP and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press SELECT and the display
screen will change to [LDP].
6
MENUSELECT
POWER
or
PL
ESC
Press MENU - to toggle between
[LDP], [DVD], [TAPE] and [DAT].
Once [DVD] is on the display
screen, enter the first DVD Player
code listed for your brand in the “Set
Up Codes for DVD Players” on page
25, then press SELECT. Point the
remote control at the DVD Player
and press POWER or PLAY. Your
DVD Player should turn OFF or play
your disc. If your DVD Player turns
OFF or plays your disc, press the
ESC key to return the display to
[DVD and the TIME]. If your DVD
Player does not turn OFF or play
your disc, enter the next code in the
code list then press SELECT
followed by POWER or PLAY again.
Once the correct code is entered,
press the ESC key to return the
display to [DVD and the TIME].
Re-assigning Device Keys
You can use the A/V Producer to operate a second
TV or a second VCR or any combination of eight
devices. To do this, you must re-assign one of the
device keys (TV, VCR/LD, CBL, SAT, AMP, TUN or
CD) to operate your second device. For example, to
re-assign one of the device keys to support your
other components:
1
MAGIC
2
MENUSELECT
3
MENU-
SELECT
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
x 2 Press the MENU - key twice. The
display screen will change to
[CONFIGURE]. Press SELECT.
The display will change to
[THEATER SEL].
x 3 Press the MENU - key three times.
The display screen will change to
[MODE MAP]. Press SELECT. The
display screen will change to
[SOURCE].
4
(Device Key)
Press the device key you would like
to move (for DVD Players it would be
AUX1 or for a second TV, it would
be the TV key). The display screen
will change to [COPY TO]. Now
press the unused device key you
would like to replace. The display
will change to [DEVICE2 and the
TIME]. Now, proceed with programming the re-assigned device key
with the appropriate code.
Note: Initially, moving AUX 1 to another key will
display [LDP2]. To access [DVD2], you must follow
instructions on page 25 to access "Additional Home
Entertainment Components."
Set Up Codes for DVD Players
Philips
Panasonic
482
490
Toshiba
503
Set Up Codes for Cassette Decks
ADC
Aiwa
Akai
Carver
Denon
Fisher
Garrard
Goldstar
JVC
Kenwood
Kyocera
Magnavox
Marantz
MGA
Mitsubishi
171
029, 197, 200
283
029, 261
076, 421
074, 261
300, 308, 309,
375, 439, 448
421
244, 273, 274,
303, 310
070, 071, 092,
233, 234
171
029
029
313
283, 313
Nakamichi
Onkyo
Optimus
Philips
Pioneer
RCA
Sansui
Sharp
Sherwood
Sonic
Sony
TEAC
Technics
Victor
Wards
Yamaha
147, 151, 218,
247, 248
136, 282
027, 220, 300,
337, 439
029
027, 099, 220
261
029
231
337
375
170, 243, 291
280, 289, 308,
309
229, 353
273, 274
027
094, 097
Set Up Codes for Home Automation
Audio Access
GE
LiteTouch
Lutron
One For All X10
Security System
154
240
084
318
ProPresenter
RadioShack
Sanyo
Universal X10
X10
607, 672
240
336
167
167
167
Set Up Codes for Digital Audio Tape
Carver
Marantz
Philips
158
158
158
Set Up Codes for Phonographs
Aiwa
Carver
Magnavox
188
188
188
Marantz
Philips
188
188
SEARCHING FOR YOUR CODE
Set Up Codes for Video Accessories
Rabbit
Roctec
081
456
SuperGuide
TeleCaption
169
171
Set Up Codes for Miscellaneous Audio
Adcom
Aiwa
AudioSource
BSR
Cambridge
Soundworks
Carver
Fisher
Fosgate
HarmanKardon
JBL
Jerrold
JVC
KLH
Magnavox
577
010, 159
351
392
351
351
052
259, 447
447
447
459, 520
073
351
325
Nikko
Paramount
Pictures
376
RCA
Sansui
Schneider
Scientific Atlanta
Sony
Soundesign
Soundstream
SSI
Starcom
Yamaha
Yorx
056
325
376
460
010, 159
376
447
317
459
292
376
317, 351
If your components do not respond to the A/V
Producer after trying all of the codes listed for your
brand, or if your brand is not listed at all, try
searching for your code. For example, after trying all
of the codes for your brand of TV, you still cannot
get the A/V Producer to operate your TV, then:
1
TV
2
MAGIC
3
MENU-
SELECT
4
MENUSELECT
Press and release the TV key.
Press and hold MAGIC until the
display screen changes from
[TV and the TIME] to [TIMED SEQ].
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Press the MENU - key one time.
The display screen will change to
[DEV SEARCH]. Press SELECT.
The display will change to
[TV and XXX].
Note: XXX represents the last 3 digit code that was
entered prior to starting the search.
5
POWER
SELECT
or
MENU-
Press POWER. If your TV turns
OFF, press SELECT to lock in your
code and return the display to
[TV and the TIME]. If your TV does
not turn OFF, press MENU -. The
next available code will appear on
the display screen, then press
POWER again. Continue to press
POWER then MENU - until your TV
turns OFF. Once your TV turns OFF,
press SELECT to lock in your code
and return the display to
[TV and the TIME].
Note: If you are searching for your VCR, CD Player,
Laser Disc Player or DVD Player code, you may
want to use PLAY instead of POWER. Once your
component plays, press SELECT to lock in your
code.
Finding Your Code
After you have set up your components using the
search, you may need to find out which three-digit
code is operating your components. For example, to
find out what three-digit code is operating your TV:
1
Press and release the TV key.
TV
SETTING UP THE HOME THEATER MODE KEY
The HOME THEATER mode key brings all of the
most commonly used home theater functions into
one mode of the A/V Producer. When setting up the
HOME THEATER mode key, you will choose which
components will control your volume, channel
changing, Playback, Picture-in-Picture and menu
functions.
1
2
Press and hold MAGIC until the
display screen changes from
[TV and the TIME] to [TIMED SEQ].
MAGIC
3
Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
MENUSELECT
HOME THEATER
2
MENU-
4
MENU-
SELECT
x 2 Press the MENU - key two times.
The display screen will change to
[DEV NUMBER]. Press SELECT.
The display screen will then change
to [TV and your code]. Once you
have written your three-digit code
down, press ESC to return the
display to [TV and the TIME].
SELECT
4
VCR Code
Cable Code
Satellite Code
x 2 Press the MENU - key twice, the
display will change to
[CONFIGURE]. Press SELECT, the
x2
display will change to [THEATR SEL],
press SELECT. The display will
change to [AUDIO].
SELECT
(Device Key)
SELECT
TV code
Press and hold MAGIC until the
display screen changes from
[THEATER and the TIME] to
[TIMED SEQ].
MAGIC
3
Press and release the HOME
THEATER mode key.
Press SELECT. This will change the
display to [AMP]. At this screen you
will select the device that will control
your Volume in the Home Theater
Mode. Use the device keys (AMP,
TUNER, TV, CABLE, SAT or AUX 1)
to choose your AUDIO selection.
Once you choose the AUDIO
source, press SELECT. For example, if your Tuner will control your
volume in the Home Theater Mode,
press TUN + SELECT. The display
will change to [CHANNEL]. This will
allow you to choose the device that
will control your channel changing.
(continued on next page)
Tuner Code
Amplifier Code
CD Player Code
AUX1 Code
5
SELECT
(Device Key)
SELECT
6
SELECT
(Device Key)
SELECT
7
SELECT
(Device Key)
SELECT
Press SELECT. This will change the
display to [SAT]. Use the device
keys (TV, VCR, SAT, CBL or AUX 1)
to choose your CHANNEL source,
then press SELECT. For example, if
your Satellite will control your
channel changing in the Home
Theater Mode, press SAT +
SELECT. The display will change
to [PLAYBACK]. This will allow you
to choose the device that will control
the transport keys (PLAY, REW, FF,
PAUSE, STOP and REC).
Press SELECT. This will change the
display to [VCR]. Use the device
keys (CD, VCR or AUX 1 [LD]) to
choose your PLAYBACK source,
then press SELECT. For example, if
your Laser Disc Player will control
your playback in the Home Theater
Mode, press AUX 1 + SELECT. The
display will change to [PIP]. This will
allow you to select the device that
will control your Picture-in-Picture
features.
Press SELECT. This will change the
display to [TV]. Use the device keys
(TV, CBL or VCR) to choose your
PICTURE-IN-PICTURE source,
then press SELECT. For example,
if your VCR will control your Picturein-Picture features in the Home
Theater Mode, press VCR +
SELECT. The display will then return
to [MENU]. This will allow you to
select the device that will control
your Menu features.
8
SELECT
(Device Key)
SELECT
Press SELECT. This will change the
display to [SAT]. Use the device keys
(TV, CBL, SAT, VCR, TUNER or
AUX1) to choose your MENU
source, then press SELECT. For
example, if your DSS will control your
Menu features in the Home Theater
mode, press SAT + SELECT. The
display will then return to the
[DEVICE and the TIME] SCREEN.
After you have set up the HOME THEATER mode
key, you can then set up a macro sequence on the
POWER key in the Home Theater Mode. The
POWER key macro will allow you to power ON all of
your components in the Home Theater mode with
the press of one key.
Power Key Macro - Powering ON Your Home
Theater Components with One Key Press
1
Press and release the HOME
THEATER Mode key, then press
HOME THEATER
and hold MAGIC until the display
screen changes from
MAGIC
[THEATER and the TIME] to
x 2 [TIMED SEQ]. Press the MENU key twice, the display will change to
MENU[CONFIGURE]. Press SELECT, the
SELECT
display will change to [THEATR SEL].
2
x 4 Press MENU - four times until the
display reads [KEY MACRO]. Press
SELECT. The display will read
[SEL MACKEY].
MENUSELECT
3
POWER
(Sequence)
Press the POWER key to assign the
macro to POWER. Enter the macro
sequence that will power “ON” your
home theater, for example:
TUN + POWER + TV + POWER +
VCR + POWER + Etc. until you have
added all of your home theater
components.
4
ESC
POWER
When your macro sequence is
concluded, press ESC to save. The
display will then return to the
[THEATER and the TIME] screen.
To activate the Home Theater Power
macro, the LCD screen must read
[THEATER], and you must press
POWER.
Note: The AUD or VID macro keys cannot be used
in your Home Theater Power key macro.
SETTING UP TIMED SEQUENCES RECORDING WHEN YOU ARE NOT HOME
The A/V Producer is equipped with a special feature
that lets the user set up a sequence of key strokes
that can be played back at a specified time, up to
seven days in advance. This feature can be used to
set up sequences that will record from your DSS
satellite, turn on your infrared home automation
lighting system when you are not home or any other
series of keystrokes that you would like to play back
at a later time. For example, to set up the remote to
record a program off of your DSS Satellite:
1
MAGIC
SELECT
SELECT
2
0
or
1
MENU-
SELECT
3
MENU-
SELECT
4
MENUSELECT
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ]. Press SELECT. The
display will change to [ADD MACRO].
Press SELECT again.
The display will change to
[START and the TIME], with the first
digit of the TIME blinking. Enter
either a 0 or a 1, then the next digit
in the time will begin to blink,
continue entering the time until all
four digits of the time have been set.
After the time has been set, AM/PM
will then blink. Press MENU - to
toggle between AM and PM, once
AM or PM is selected, press SELECT.
The display will then change to
[ONCE]. Use the MENU - key to
toggle between [ONCE], [DAILY] or
[WEEKLY], depending on when and
how often the sequence needs to
play. After [ONCE], [DAILY] or
[WEEKLY] is chosen, press SELECT.
The display will change to the day of
the week that you want the sequence to begin. Use MENU - to
toggle through the days of the week
until the proper day is on the display
screen. Press SELECT. The
display will change to
[ENTER SEQ].
(continued on next page)
For example, enter a sequence that
will start your VCR recording your
DSS Satellite channel.
To Delete a Timed Sequence
1
SAT + POWER + SAT + 2 + 7 + 5 +
VCR + POWER + VCR + RECORD.
SELECT
This sequence will turn on the DSS,
change the channel to 275, turn on
the VCR and start the VCR recording.
MENUSELECT
2
Note: When setting up your sequence, you will need to include any
keystrokes that would normally be
required during regular usage, such
as pressing ENTER after entering a
channel number when changing
channels.
5
ESC
Once the sequence has been set
up, press the ESC key to return to
the [DEVICE and the TIME] display
screen. Below the [TIME], a
CLOCK ( ) symbol will appear to
show that there is a timed sequence
in the memory.
Note: If, at any time during the set up of your timed
sequence, a mistake is made, press the ESC key to
return to the main display [DEVICE and the TIME] .
Now, delete the sequence that was incorrect and
restart your timed sequence.
After you have set up a timed sequence, you may
want to set up a second sequence that turns
everything off after your initial sequence is complete.
For the example above, after recording the program
from your DSS, you can set up a second sequence
to power OFF your DSS and VCR. Repeat Steps
1 - 5 to set up a sequence to power OFF your
components.
MAGIC
SELECT
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ]. Press SELECT. The
display will change to [ADD MACRO].
Press MENU - one time. The
display will change to [DEL MACRO].
Press SELECT.
The display will then change to
[DEL (the DAY) and (the TIME)]. If
this is the timed sequence you
would like to delete, press SELECT.
The display will change to
[DELETED] then return to
[DEVICE and the TIME].
Note: If you have more than one timed sequence
saved in the memory of the A/V Producer, use the
MENU - key to scroll through your saved timed
sequences until you see the sequence you would
like to delete. Once the sequence is displayed on
the screen, press SELECT. The display will change
to [DELETED] then return to the next available
sequence to be deleted. If there are no other
sequences to be deleted, then the display will return
to [DEVICE and the TIME].
For example, enter a sequence that
will start your VCR recording your
DSS Satellite channel.
To Delete a Timed Sequence
1
SAT + POWER + SAT + 2 + 7 + 5 +
VCR + POWER + VCR + RECORD.
SELECT
This sequence will turn on the DSS,
change the channel to 275, turn on
the VCR and start the VCR recording.
MENU-
SELECT
2
Note: When setting up your sequence, you will need to include any
keystrokes that would normally be
required during regular usage, such
as pressing ENTER after entering a
channel number when changing
channels.
5
ESC
Once the sequence has been set
up, press the ESC key to return to
the [DEVICE and the TIME] display
screen. Below the [TIME], a
CLOCK ( ) symbol will appear to
show that there is a timed sequence
in the memory.
Note: If, at any time during the set up of your timed
sequence, a mistake is made, press the ESC key to
return to the main display [DEVICE and the TIME] .
Now, delete the sequence that was incorrect and
restart your timed sequence.
After you have set up a timed sequence, you may
want to set up a second sequence that turns
everything off after your initial sequence is complete.
For the example above, after recording the program
from your DSS, you can set up a second sequence
to power OFF your DSS and VCR. Repeat Steps
1 - 5 to set up a sequence to power OFF your
components.
MAGIC
SELECT
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ]. Press SELECT. The
display will change to [ADD MACRO].
Press MENU - one time. The
display will change to [DEL MACRO].
Press SELECT.
The display will then change to
[DEL (the DAY) and (the TIME)]. If
this is the timed sequence you
would like to delete, press SELECT.
The display will change to
[DELETED] then return to
[DEVICE and the TIME].
Note: If you have more than one timed sequence
saved in the memory of the A/V Producer, use the
MENU - key to scroll through your saved timed
sequences until you see the sequence you would
like to delete. Once the sequence is displayed on
the screen, press SELECT. The display will change
to [DELETED] then return to the next available
sequence to be deleted. If there are no other
sequences to be deleted, then the display will return
to [DEVICE and the TIME].
REPEATING SERIES OF KEY PRESSES USING
THE AUD AND VID KEYS
The A/V Producer has two Macro keys (AUD and
VID) that allow the user to play back a series of key
strokes at any time with the press of one key. Each
sequence can have up to a maximum of 15
keystrokes. These keys are not mode specific and
can be accessed in any mode. For example, to set
up a sequence that will turn on your devices and turn
the devices to the proper inputs:
1
MAGIC
MENUSELECT
2
MENUSELECT
AUD
or
VID
3
ESC
When your macro sequence is
concluded, press ESC to save.
Whenever the sequence key is pressed, the Tuner
will power ON, the TV will power ON and change the
input to VIDEO 1 and then the Satellite will power
ON.
Repeat these steps to then setup the other sequence key (either AUD or VID) to your needs.
HOW TO USE THE SHIFT KEY
Press and hold MAGIC until the
display screen changes from
x 2 [DEVICE and the TIME] to
[TIMED SEQ]. Press MENU twice until the display reads
[CONFIGURE], then press SELECT.
The display will then read
[THEATR SEL].
The A/V Producer has features that can be
accessed by using the SHIFT key. These features
are listed above the key that they are mapped to.
For example, on the transport keys (PLAY, REW,
FF, STOP and PAUSE) there are the following
features: SLOW, SLOW +, SLOW -, X2 and EJECT.
These are accessed by pressing SHIFT and the key,
for example, to eject a tape from your VCR press:
x 4 Press MENU - four times until the
display reads [KEY MACRO]. Press
SELECT. The display will read
[SEL MACKEY]. Press either the
AUD or VID sequence key. This will
be the key that will play back the
series of keystrokes assigned to that
key. The display will then read
[SELECT SEQ]. Begin entering the
sequence of keystrokes, up to 15,
that you wish to be played back
when you press either AUD or VID.
SHIFT + STOP
Note: You cannot use either the AUD or VID keys in
your macro sequence.
For example:
(Sequence)
TUN + POWER + TV + POWER +
TV/SAT (To change the input on the
TV to VIDEO 1) + SAT + POWER.
Note: When setting up your sequence, you will need
to include any keystrokes that would normally be
required during regular usage, such as pressing
ENTER after entering a channel number when
changing channels
This will eject your tape, as long as your original
remote supported this feature.
Note: Once you have pressed the SHIFT key, the
A/V Producer will remain in the "Shift" mode,
indicated by an S on the LCD screen, for 10
seconds after the last key press or until the SHIFT
key is pressed again.
The following keys have functions that are shifted:
CENTER:
MENU:
SELECT:
MUTE:
PREV CH:
PIP:
REW:
PLAY:
FF:
STOP:
PAUSE:
SHIFT + CENTER = REAR
SHIFT + MENU = PROGRAM
SHIFT + SELECT = CLEAR
SHIFT + MUTE = SLEEP
SHIFT + PREV CH = DISPLAY
SHIFT + PIP = FREEZE PIP
SHIFT + REW = SLOWSHIFT + PLAY = SLOW
SHIFT + FF = SLOW +
SHIFT + STOP = EJECT
SHIFT + PAUSE = X2
Important: For a more detailed explanation of what
function each shifted key performs by device type
(TV, VCR, etc.), please refer to pages 45 through 57
HOW TO USE THE SLEEP KEY
The A/V Producer has a SLEEP key that either
operates your component’s sleep timer or, if your
component does not have a sleep timer, it activates
the A/V Producer built-in sleep timer. To use the
A/V Producer’s SLEEP key, press SLEEP (SHIFT +
MUTE).
If your component does not have a sleep timer, the
A/V Producer will access it’s own built-in timer. To
activate the built-in sleep timer, press SLEEP
(SHIFT + MUTE). The display will change to
[SLEEP 15]. To add time to the sleep timer, press
MENU -. Each press of MENU - will add 15 minutes
to the sleep timer, up to a total of 60 minutes. Once
the desired time is displayed on the LCD screen,
press SELECT. The display screen will change to
[SLEEP and the TIME].
Sleep lock
MAGIC
With the A/V Producer, you can choose which home
entertainment component controls your volume in
the TV, VCR, CBL and SAT modes. When you
originally set up the A/V Producer, each individual
component operates it’s own volume, provided the
component has volume control. You can change
this setting so that one component controls the
volume whether you are in the TV, VCR, CBL or
SAT modes. For example, to set-up the A/V
Producer to always control the volume through your
Amplifier in the TV, VCR, CBL and SAT modes:
1
MENUSELECT
3
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
MAGIC
2
If you would like the A/V Producer to use it’s built-in
sleep timer on all of your components, you can lock
the SLEEP mode. To set-up the A/V Producer to use
the internal sleep timer on all components:
1
VOLUME LOCK
MENUSELECT
x 2 Press the MENU - key twice, the
display will change to
[CONFIGURE]. Press SELECT, the
display will change to [THEATR SEL].
x 2 Press MENU - two times, the display
will read [VOL LOCK]. Press
SELECT, the display will change to
[UNLOCK].
4
2
MENU-
SELECT
MENU+
SELECT
3
x 2 Press the MENU - key twice, the
display will change to [CONFIGURE].
Press SELECT, the display will
change to [THEATR SEL]. Press
MENU + two times, the display will
read [SLEEP LOCK]. Press
x 2 SELECT, the display will change to
[DISABLE].
Press MENU - one time to change
the display to [ENABLE] then press
MENUSELECT. The display will return to
SELECT
[DEVICE and the TIME]. Now,
whenever you press SLEEP (SHIFT
+ MUTE), the A/V Producer will use
it’s own built-in sleep timer.
Note: When using the built-in sleep timer, pressing
POWER will cancel the sleep function.
MENUSELECT
(Device Key)
Press MENU - one time to change
the display to [LOCK] then press
SELECT. Now press the key for the
component that will control your
volume. In this example, to control
the volume through your amplifier,
press AMP. The display will return
to [DEVICE and the TIME].
Now, when you use the volume keys on your
A/V Producer, the volume will be controlled by the
specified component.
To return volume control to each individual
component:
1
MAGIC
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
2
MENUSELECT
3
MENUSELECT
4
MENUSELECT
x 2 Press the MENU - key twice, the
display will change to
[CONFIGURE]. Press SELECT, the
display will change to [THEATR SEL].
x 2 Press MENU - two times, the display
will read [VOL LOCK]. Press
SELECT, the display will change to
[LOCK].
Press MENU - one time to change
the display to [UNLOCK] then press
SELECT. The display will return to
[DEVICE and the TIME].
Now, when you use the volume keys on your
A/V Producer, each component will control it’s own
volume, as long as that component originally had
volume control.
KEYMOVER
Keymover allows you to map features from one
device mode to another. For example, if your VCR
does not have volume control, you can map the
volume keys in the TV mode to the VCR mode. This
will allow you to control the volume of your TV while
using your VCR. To Keymover features from one
mode to another:
1
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
MAGIC
2
MENUSELECT
MENU+
SELECT
3
x 2 Press the MENU - key twice, the
display will change to [CONFIGURE].
Press SELECT, the display will
change to [THEATR SEL]. Press
MENU + three times, the display will
x 3 read [KEY MOVER]. Press
SELECT, the display will change to
[FROM].
(Device Key)
4
VOL-
VOL+
(Device Key)
Press the device key (TV, VCR,
CBL, etc.) that contains the feature
you want to move. For the example
above, to move the TV’s volume, you
would press TV. The display will
show the device key that was just
pressed.
Press the key for the feature you
want to move. For the example
above, press VOL +. The display
will change to [TO]. Press the
device key (TV, VCR, CBL, etc.)
where you would like to place the
feature. For the example above, you
would press VCR. The display will
show the device key that was just
pressed.
5
VOL-
VOL+
Press the key where you want to
move the feature. For the example
above, press VOL +. The display
will return to [DEVICE and the TIME].
In the VCR mode, your
A/V Producer will now operate
volume up on your TV. Now, to
complete the example above, repeat
this sequence to move VOL - and
MUTE from the TV mode to the
VCR mode.
CLEAR ALL
If you would like to reset the A/V Producer of all
advanced functions, use the CLEAR ALL feature.
The CLEAR ALL feature will erase the following
functions from the memory of the A/V Producer:
Macro Sequences, Timed Macro Sequences,
Volume Lock and Keymovers. CLEAR ALL will not
erase your set-up codes. To clear the memory using
the CLEAR ALL feature:
1
MAGIC
2
MENUSELECT
MENU+
TROUBLESHOOTING
Problem:
LCD screen begins
to fade, does not
appear or the red
light blinks five times
when you press a
key?
Replace the batteries with
four (4) new AAA alkaline
batteries.
The A/V Producer
does not operate
your home
entertainment
component?
Try all of the codes listed for
your brand of home
entertainment component
in the “Set-Up Codes”
section. If this does not
work, try searching for your
code. Make sure the home
entertainment component
you are setting up is able
to be operated with an
infrared remote control.
The A/V Producer is
not performing
commands properly?
Try all of the codes listed for
your brand of home
entertainment component
in the “Set-Up Codes”
section. Many set-up codes
may allow some degree
of operation. However, only
one set-up code will work
correctly with your home
entertainment component.
You make a mistake
when setting up your
A/V Producer?
During any set up procedure,
except for Macros and Timed
Sequences, the ESC key will
return you to the
[DEVICE and the TIME]
screen without saving. If you
make a mistake when setting
up a Timed Sequence, return
to the Timed Sequence
menu and delete the
incorrect sequence. If you
make a mistake when saving
a Macro, erase the incorrect
Macro by re-saving a new
Macro on that key.
VCR not recording?
As a safety feature on the
A/V Producer, you must
press the REC key twice.
Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
x 2 Press the MENU - key twice, the
display will change to [CONFIGURE].
Press SELECT, the display will
change to [THEATR SEL]. Press
MENU + one time, the display will
read [CLEAR ALL]. Press SELECT,
the display will change to [CLR ALL].
SELECT
3
SELECT
Solution
x 2 Press SELECT, the display will
change to [CONFIRM]. Press
SELECT once more and the display
will return to [DEVICE and the TIME].
Your A/V Producer is now reset.
TROUBLESHOOTING (cont.)
Problem:
Solution
Channel +/- and
PREV CH not
working for your
RCA TV?
Due to RCA design (19831987), only the original
remote control will operate
these functions.
Problems changing
channels?
If your original remote control
required an ENTER
keystroke when changing
channels, press the ENTER
key on the A/V Producer
after you enter the
channel number.
The red light blinks
when you press a
key but you receive
no response from
your home
entertainment
component?
Make sure you are aiming
your A/V Producer at your
home entertainment
component and that you are
within 15 feet before using
your remote.
Your audio
components turn on
and off and control
the volume but does
not change your
preset channels?
Some audio components
may need both a Tuner/
Receiver code and an
Audio Amplifier code to
control all of the features of
your audio component.
Your DSS satellite
receiver does not
respond to the codes
listed in the
manual?
The codes listed in the
manual are set up to operate
your DSS receiver on
the 1st or 2nd addresses
only. Make sure the DSS
Receiver you are
setting up is able to be
operated with an infrared
remote control and
not set up to only receive
Radio Frequency.
The A/V Producer is
not operating your
Bang & Olufsen
equipment?
Some Bang & Olufsen
products, as well as some
other manufacturer’s
equipment operate at a
frequency higher than 100
kHz and will not work with
the A/V Producer.
Consumer Help Line: 1-330-405-8552
World Wide Web: http://www.oneforall.com
WARRANTY
One For All PRODUCTS
Limited Warranty
Universal Electronics Inc. (“UEI”) warrants, to the original
purchaser only, that this product will be free from defects in
materials and workmanship, under normal use, for ninety
(90) days from the date of original purchase.
This warranty does not cover damage or failures caused by
products or services not supplied by UEI, or which result
from accident, misuse, abuse, neglect, mishandling,
misapplication, faulty installation, set-up adjustment,
improper maintenance, alteration, maladjustment of
consumer controls, modifications, commercial use, or that
is attributable to acts of God.
There are no express warranties except as listed above.
UEI SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THIS PRODUCT OR ARISING OUT OF ANY
BREACH OF WARRANTY. ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD
SET FORTH ABOVE. Some states do not allow the
exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply
to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
To obtain warranty service for a defective product during
the warranty period, please return the product, preferably
in the original carton, along with your purchase receipt, to
the store of original purchase. A note detailing the complaint
would be helpful. The store, at its option, will replace or
repair this product if found to be defective.
Universal Electronics Inc.
(330)-405-8655
As you add new components to your home
entertainment system, One For All has a remote
control that will fit your needs. Look for these
exciting products at a retailer near you.
One For All® and A/V Producer are trademarks of
Universal Electronics Inc.
URC-8080 - 17 - REV - A
A/V Producer
M4057
McK
2/98
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising