Comet Labs | 48-Port 10 | User manual | Comet Labs 48-Port 10 User manual

Comet Labs 48-Port 10 User manual
w w w. m g e o p s . c o m
EX 5/7/11 RT Systems
Installation and User Manual
Installation and User Manual
EX 5/7/11 RT Systems
Installation and User Manual
Revision History
E X 5 / 7 / 11 RT S y s t e m s I n s t a l l a t i o n a n d U s e r M a n u a l , 8 6 - 8 6 0 0 0 - 0 0
Revision:
A01
ECN#: 003984
07/2004
A02
ECN#: 004086
11 / 2 0 0 4
A03
ECN#: 004284
05/2005
B00
ECN#: 004379
03/2006
B01
ECN#: 005020
10/2006
Copyright © 2007 MGE Office Protection Systems
All rights reserved. Printed in U.S.A.
MGE Office Protection Systems
13 Whatney, Suite #101
Irvine, CA 92618
(949) 268-2800
For Technical Support, Customer Care Center, or Customer FAQ,
please visit our website: www.mgeops.com or call (800) 279-7776
86-86000-00 B01
iii
EX 5/7/11 RT Systems
(This page left blank intentionally)
iv
86-86000-00 B01
Contents
section
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . .c vi
Certification Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c vi
CAUTION: Safety of Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c vii
CAUTION: Product Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c vii
Special Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c vii
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c vii
CAUTION: Record All Serial Numbers! . . . . . . . . . . . . . . . . . . . . . .c viii
Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c ix
Section Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .c ix
Section 1
Introduction
1.0
1.1
1.2
1.2.1
1.2.2
1.3
1.3.1
1.3.2
1.3.3
1.4
1.5
1.5.1
1.5.2
1.5.3
1.5.4
1.5.5
1.5.6
1.5.7
1.5.8
86-86000-00 B01
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 1
System Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . .1 — 3
Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4
Tower Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4
Rack Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 5
Rear Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
Power Module EX 5/7/11 RT . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
Battery Module EXB 5/7/11RT With Remote
Emergency Power Off (REPO) Function . . . . . . . . . . . . . . . . . . .1 — 6
EX RT Transformer Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 7
Power Module Display and Control Panel . . . . . . . . . . . . . . . . . .1 — 7
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
Power Module Rail Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
Battery/Transformer/CLA Module Rail Kit . . . . . . . . . . . . . . . . . . .1 — 8
Multiple Battery Module Back-up Time at Full Load . . . . . . . . . . .1 — 9
Battery Extension Cable Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 9
Battery Integration Kit with Casters . . . . . . . . . . . . . . . . . . . . . .1 — 10
Input/Output Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 10
Transformer Module – For Use With EX 5/7/11 RT
Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 11
CLA Charger Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 12
Contents
ci
EX 5/7/11 RT Systems
section
Section 2
Setup and Installation
2.0
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.4.3
2.5
2.5.1
2.5.2
2.5.3
2.6
2.7
2.7.1
2.7.2
2.7.3
2.7.4
2.8
2.9
Section 3
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 1
Unpacking and Parts Check . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 1
Contents of Standard EX 5/7/11 RT Systems . . . . . . . . . . . . . . .2 — 2
Installation in Tower Configuration . . . . . . . . . . . . . . . . . . . . . . . .2 — 4
Installation in Rack Mounting Configuration . . . . . . . . . . . . . . . . .2 — 5
Adjustment of Front Panel Logo and Control Panel
for Rack Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 5
Prepare Battery Module for Rack Mounting . . . . . . . . . . . . . . . .2 — 6
Power, Battery, Transformer, and CLA Charger Module
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 7
Communication Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 9
Connecting the RS232 Communication Port . . . . . . . . . . . . . . .2 — 9
Connecting the Dry (Relay) Contact Communication Port . . . .2 — 10
Installation of Optional Transverse Card . . . . . . . . . . . . . . . . . .2 — 10
Remote Emergency Power Off (REPO) Communication Port . .2 — 12
System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 13
Connections with Common Normal and Bypass AC
Sources (Single Mains) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 13
Connecting EX RT Transformer Module . . . . . . . . . . . . . . . . . .2 — 15
Connections with Separate Normal and Bypass AC
Sources (2 Mains) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 16
System Connections as Frequency Converter
(without Bypass AC Source) . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 17
Connection of Battery Module EXB . . . . . . . . . . . . . . . . . . . . . .2 — 18
Connection of Optional CLA Module . . . . . . . . . . . . . . . . . . . . .2 — 19
Operation
3.0
3.1
3.2
3.2.1
3.3
3.3.1
3.3.2
3.4
3.4.1
3.4.2
3.5
3.5.1
3.6
3.7
c ii
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 1
Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 1
UPS Personalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 2
Accessing Personalization With Front Panel Buttons . . . . . . . . .3 — 2
Information Technology (IT) Network and Industrial
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 5
UPS Personalization Through External Software . . . . . . . . . . . . .3 — 6
Final Startup Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 6
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 7
Normal (Double Conversion) Mode . . . . . . . . . . . . . . . . . . . . . . .3 — 7
ECO Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 8
Operation on Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 9
Transfer to Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 9
Return of Normal AC Source . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 10
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 10
Contents
86-86000-00 B01
Installation and User Manual
section
Section 4
Maintenance
4.0
4.1
4.2
4.3
4.4
4.4.1
4.4.2
Section 5
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 1
Hot Swapping the Power Module . . . . . . . . . . . . . . . . . . . . . . . . .4 — 3
Re-connecting the Power Module . . . . . . . . . . . . . . . . . . . . . . . .4 — 4
Hot Swapping the Battery Module . . . . . . . . . . . . . . . . . . . . . . . .4 — 5
Disconnecting the Battery Module . . . . . . . . . . . . . . . . . . . . . . . .4 — 5
Re-connecting the Battery Module . . . . . . . . . . . . . . . . . . . . . . . .4 — 5
Appendix
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 1
System Input/Output Power Ratings . . . . . . . . . . . . . . . . . . . . . .5 — 1
System Overload Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .5 — 1
System Back-up Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 2
System Short Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 2
Accessories Electrical Characteristics . . . . . . . . . . . . . . . . . . . . .5 — 2
Heat Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 4
Environmental Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 4
Customer Care Center – Single Phase Products
Technical Support and Product Services
Who to Contact
Scheduling Field Service Engineer Support
Return Policy for Repair of Single Phase Products (RGA)
Glossary
Reorder Form
86-86000-00 B01
Contents
c iii
EX 5/7/11 RT Systems
Figures
figure description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
1-1:
Tower Configuration with Power Module, Battery Module,
and Optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4
1-2: Rack Configuration with Power Module, Battery Module,
and Optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 5
1-3: Rear Panel of the Power Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
1-4: Rear Panel of the Battery Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
1-5: Rear Panel of the Optional Transformer Module. (PN 86211) . . . . . . . . .1 — 7
1-6: View of Typical Control Panel Interface. . . . . . . . . . . . . . . . . . . . . . . . . .1 — 7
1-7: Power Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
1-8: Battery/Transformer/CLA Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
1-9: Typical Back-Up Time With Multiple EXBs at Full Load. . . . . . . . . . . . . .1 — 9
1-10: Typical Battery Integration Kit with Casters Setup. . . . . . . . . . . . . . . . .1 — 10
1-11: Typical Transformer Module Contents and Connections. . . . . . . . . . . . .1 — 11
1-12: CLA Module Contents and Connections. . . . . . . . . . . . . . . . . . . . . . . . .1 — 12
2-1: Contents of EX 5/7/11 RT Power Module. . . . . . . . . . . . . . . . . . . . . . . . .2 — 2
2-2: Contents of EXB 5/7/11RT Battery Module. . . . . . . . . . . . . . . . . . . . . . . .2 — 3
2-3: Tower Configuration of Standard System and
Optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 5
2-4: Typical Orientation of the Logo and Control Panel.
(Power Module Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 6
2-5: Accessing Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 6
2-6: Rack Mounting of the Power Module Onto the Rails. . . . . . . . . . . . . . . .2 — 7
2-7: Input/Output Box Bracket System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 8
2-8: RS232 Communication Cable Connection. . . . . . . . . . . . . . . . . . . . . . . .2 — 9
2-9: Relay Pin Connections for Communication Port. . . . . . . . . . . . . . . . . . .2 — 10
2-10: Communication Card Slot with Network
Management Card Installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 10
2-10a: Activation of Remote Emergency Power Off Function
Using a Contact Normally Open Switch. . . . . . . . . . . . . . . . . . . . . . . . .2 — 12
2-10b: Activation of Remote Emergency Power Off Using a
Contact Normally Closed Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 12
2-11: Power Module I/O Box Terminal Block Diagram. . . . . . . . . . . . . . . . . . .2 — 13
2-12: Normal AC Input and Output Cables Installation. . . . . . . . . . . . . . . . . .2 — 14
2-13: View of EX RT Transformer Module Connected Downstream
for 120/208/240 VAC Outputs (Shown With One EXB). . . . . . . . . . . . .2 — 15
2-14: Normal AC Input, Bypass AC, and Output Cables Installation,
and Simplified Connection Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 16
2-15: Accessing Terminal Blocks for Input and Output Power Cables. . . . . .2 — 17
2-16: Rear View of Battery Module Cable Connections. . . . . . . . . . . . . . . . . .2 — 18
2-17: Rear View of CLA Module Cable Battery and AC Input Connections . .2 — 19
c iv
Contents
86-86000-00 B01
Installation and User Manual
Figures
(continued)
figure description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
3-1:
3-2:
3-3:
3-4:
3-5:
3-6:
3-7:
4-1:
4-2:
4-3:
5-1:
Initial Startup Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 1
Control Panel with Scroll Up and Down Buttons. . . . . . . . . . . . . . . . . . . .3 — 2
Configuration Used to Provide Cascade Redundancy to Critical Loads .3 — 3
Normal (Double Conversion) Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 7
ECO Mode Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 8
Transfer, Threshold, and End of Back-up Time . . . . . . . . . . . . . . . . . . . .3 — 9
Shutdown Display, Circuit Breaker, and AC Source Switch. . . . . . . . . .3 — 10
Disconnecting the Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 3
Reconnect the Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 4
Rear view of the Battery Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 5
Power Supplied as a Function of Input Voltage (Left),
and Permissible UPS Overloads as a Function of Time (Right) . . . . . . .5 — 1
Tables
table description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
1-1:
1-2:
1-3:
1-4:
1-5:
1-6:
1-7:
3-1:
3-2:
3-3:
3-4:
3-5:
4-1:
4-2:
5-1:
5-2:
5-3:
5-4:
5-5:
5-6:
5-7:
5-8:
86-86000-00 B01
EX RT Model Descriptions and Contents. . . . . . . . . . . . . . . . . . . . . . . . .1 — 1
Optional Accessories (See Section 1.5 for Description) . . . . . . . . . . . . .1 — 2
UPS Characteristics System Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 3
Transformer Module Characteristics Ratings . . . . . . . . . . . . . . . . . . . . . .1 — 3
Battery Module Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4
System Dimensions and Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 5
Battery Back-up Time Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 12
Local Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 3
Output Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 3
ON/OFF Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 4
Battery Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 — 4
System Operation in I/T and Industrial Modes. . . . . . . . . . . . . . . . . . . . .3 — 5
Troubleshooting Not Requiring MGE Office Protection Systems
After-Sales Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 1
Troubleshooting Requiring MGE Office Protection Systems
After-Sales Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 — 2
EX 5/7/11 RT Voltages and Frequency Characteristics . . . . . . . . . . . . . .5 — 1
Back-up Time (in minutes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 2
Battery Recharge Time to Recover 90% of the Rated Back-up Time
After Discharge at Full Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 3
Efficiency Online (RL Load) and Batteries Fully Charged . . . . . . . . . . . .5 — 3
Efficiency Online (RCD Load) and Batteries Fully Charged . . . . . . . . . .5 — 3
Efficiency On Battery (RCD Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 3
Efficiency On ECO Mode (All Kinds of Load) and Batteries Fully Charged .5 — 4
Full Load Heat Rejection in BTUs/hr . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 — 4
Contents
cv
EX 5/7/11 RT Systems
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS. This manual contains important instructions
that should be followed during installation and maintenance of the UPS and batteries.
The EX 5/7/11 RT models that are covered in this manual are intended for installation in an environment within
0 to 40°C, free of conductive contaminant.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Certification Standards
c vi
◗
IEEE 587-1980/ANSI C62.41 1980 Standards for Surge Withstand Ability
◗
FCC rules and regulations of Part 15, Subpart J, Class A
◗
UL listed under 1778, Standards for Uninterruptible Power Supply Equipment
◗
IEC 61000-4-2 (ESD): level 4.
◗
IEC 61000-4-3 (Radiated field): level 3.
◗
IEC 61000-4-4 (EFT): level 4.
◗
IEC 61000-4-5 (Fast transients): level 4.
◗
IEEE-C6241 Category B (ring wave).
◗
IEC 61000-4-6 (electromagnetic field).
◗
IEC 61000-4-8 (conducted magnetic field).
Important Safety Information and Standards
86-86000-00 B01
Installation and User Manual
CAUTION: Safety of persons
◗
◗
◗
◗
The system has its own power source (the battery). Consequently, the power outlets may be energized even if the
systems is disconnected from the AC power source.
Dangerous voltage levels are present within the system. It should be opened exclusively by qualified service personnel.
The system must be properly grounded.
The battery supplied with the system contains small amounts of toxic materials. To avoid accidents, the directives listed
below must be observed:
-Never burn the battery (risk of explosion).
-Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).
-Comply with all applicable regulations for the disposal of the battery.
-Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be
taken for all handling: remove watches, rings, bracelets and any other metal objects, use tools with insulated handles.
-Do not lay tools or metal parts on top of batteries.
CAUTION: Product Safety
◗
◗
◗
◗
◗
◗
◗
◗
◗
The UPS connection instructions and operation described in the manual must be followed in the indicated order.
A protection circuit breaker must be installed upstream and be easily accessible. The system can be disconnected from
the AC power source by opening this circuit breaker.
Check that the indications on the rating plate correspond to your AC powered system and to the actual electrical
consumption of all the equipment to be connected to the system.
Never install the system near liquids or in an excessively damp environment.
Never let a foreign body penetrate inside the system.
Never block the ventilation grates of the system.
Never expose the system to direct sunlight or source of heat.
If the system must be stored prior to installation, storage must be in a dry place.
The admissible storage temperature range is -25ºC to +55ºC.
Special Precautions
◗
◗
◗
All handling operations will require at least two people (unpacking, installation in rack system).
Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be energized for a
period of 24 hours, at least once every 6 months (for a normal storage temperature less than 25°C). This charges the
battery, thus avoiding possible irreversible damage.
During the replacement of the Battery Module, it is imperative to use the same type and number of element as the original
Battery Module provided with the UPS to maintain an identical level of performance and safety. In case of doubt, don’t
hesitate to contact your MGE Office Protection Systems representative.
Environment
◗
This product has been designed to respect the environment:
It does not contain any Chlorofluorocarbon (CFC) or Hydrochlorofluorocarbon (HCFC).
◗
UPS recycling at the end of service life:
MGE Office Protection Systems undertakes to recycle, by certified companies and in compliance with all applicable regulations, all UPS products recovered at the end of their service life (contact your MGE Office Protection
Systems branch office).
Packing:
UPS packing materials must be recycled in compliance with all applicable regulations.
◗
WARNING: This product contains lead-acid batteries. Lead is a dangerous substance for the environment if it
is not properly recycled by specialized companies.
86-86000-00 B01
Safety of Persons
c vii
EX 5/7/11 RT Systems
CAUTION: Record All Serial Numbers!
RECORD ALL SERIAL NUMBERS FOR EX 5/7/11 RT AND ACCESSORIES.
THESE SERIAL NUMBERS WILL BE REQUIRED IF YOUR SYSTEM NEEDS SERVICE.
KEEP THIS MANUAL IN A PLACE WHERE YOU CAN REFERENCE THE SERIAL
NUMBERS IF SERVICE IS REQUIRED!
EX 5RT System
EX 7RT System
EX 11RT System
Power Module SERIAL NUMBER: ____________________________________________________
Battery Module SERIAL NUMBER: ____________________________________________________
Transformer Module SERIAL NUMBER: ________________________________________________
CLA Module SERIAL NUMBER: ______________________________________________________
ADDITIONAL MODULES SERIAL NUMBERS:
c viii
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
____________________________
______________________________
CAUTION: Record all serial numbers!
86-86000-00 B01
Installation and User Manual
Symbol Usage
This manual uses the following icon symbols with text to convey important information and tips.
WARNING
Indicates information provided to protect the user and service personnel
against safety hazards and/or possible equipment damage.
CAUTION
Indicates information provided to protect the user and service personnel
against possible equipment damage.
IMPORTANT
Indicates information provided as an operating instruction, or as an
operating tip.
NOTE
Indicates information provided as an operating tip or an equipment feature.
Visual
Action
Audio
LED OFF
LED ON
LED Flashing
Section Descriptions
1
Introduction
Introduction is a general description of system configurations of the EX 5/7/11 RT, and its mechanical electrical
characteristics. Additionally there is an optional accessories section with important information on MGE Office
Protection Systems products that will enhance the performance of the EX 5/7/11 RT. Please contact your MGE
Office Protection Systems representative for detailed information on these options.
2
Setup and Installation
Setup and Installation guides the user through tools and equipment required for connecting the EX 5/7/11 RT and
battery installation or replacement. Included are assembly instructions, power cable connections with wire diagrams
for configuring the product to hardware specifications.
3
Operation
Operation describes the EX 5/7/11 RT systems characteristics of indicators and controls, modes,and specifications.
The user procedures include performing software programming that will maintain optimal performance.
4
Maintenance
Maintenance includes a troubleshooting guide of symptoms and possible solutions, hot swapping the Power
module, Battery module, and testing scenarios.
5
Appendix
Electrical and Mechanical specifications for the EX 5/7/11 RT.
86-86000-00 B01
Symbol Usage
c ix
EX 5/7/11 RT Systems
(This page left blank intentionally)
cx
86-86000-00 B01
Introduction
Thank you for selecting an MGE Office Protection Systems product to protect your electrical equipment.
The product you selected is a part of the EX RT series. The EX RT series is a family of Uninterruptible Power Supply
(UPS) designed to provide safe, and reliable AC power back-up for sensitive electrical equipment. To discover the
entire range of MGE Office Protection Systems products, we invite you to visit our website at www.mgeops.com.
1.0
Scope
Introduction is a general description of system configurations of the EX 5/7/11 RT, and its mechanical electrical
characteristics. Additionally there is an optional accessories section with important information on MGE Office
Protection Systems products that will enhance the performance of the EX 5/7/11 RT. Please contact your MGE
Office Protection Systems representative for detailed information on these options.
Table 1-1: EX RT Model Descriptions and Contents.
System Description
System Contents
Power Module
Model #
Output Voltage
Battery Module
Part #
86215
86216
86217
86207
86209
5 kVA
HV EX 5RT
86050
X
X
5 kVA
LV EX 5RT
86201
X
X
7 kVA
HV EX 7RT
86070
X
X
7 kVA
LV EX 7RT
86203
X
X
11 kVA
HV EX 11RT
86110
X
X
11 kVA
LV EX 11RT
86205
X
X
Transformer
Module
86211
86311
200/208/220/
230/240/250
X
120/208/240
200/208/220/
230/240/250
X
120/208/240
200/208/220/
230/240/250
X
120/208/240
Also: All units include rail kits for rack mounting and stabilizing feet for tower configuration.
NOTE
86-86000-00 B01
The Power Module is factory configured for single Mains input at 208VAC,
60Hz. Other input-output voltage settings are available. See Section 3.2.1.
Input voltage must be the same as output voltage on HV units!
Introduction
1—1
EX 5/7/11 RT Systems
Table 1-2: Optional Accessories (See Section 1.5 for description)
1—2
Part Number
Description
86001
Rail Kit for Power Module EX 5/7/11 RT
86002
Rail Kit for Battery/Transformer/CLA Module
86005
Battery Integration Kit with Casters
86006
Battery Extension Cable Kit
86008
Empty Battery Chassis EXB RT W/EPO
86009
I/O Box 5/7kVA UL/US
86010
I/O Box 11kVA UL/US
86012
I/O Box Bracket System
86013
Rear Bracket Supports
86207
Battery Module EXB 5/7RT
86209
Battery Module EXB 11RT
86211
EX RT Transformer Module (11kVA)
86213
CLA Charger Module
86215
5kVA Power Module EX 5RT
86216
7kVA Power Module EX 7RT
86217
11kVA Power Module EX 11RT
86311
EX RT Transformer Module (7kVA)
Introduction
86-86000-00 B01
Installation and User Manual
1.1
System Electrical Characteristics
Table 1-3: UPS Characteristics System Ratings.
UPS Characteristics
MAIN 1 (Normal AC Source) default
Power
Rating
Input
Voltage
(VAC)
5 kVA
7 kVA
208
11 kVA
Input Current (A)
Min
Max
Online
Bypass
Input
Breaker
(A)
18
32
21.6
19
40
25
45
30.3
26.65
50
38
64
44
42
70
Output
Voltage
(VAC)
Output
Current
(A)
Inrush
Current
19.25
208
23.5
200A/1ms
47.5
Table 1-4: Transformer Module Characteristics Ratings.
Transformer Module Characteristics
Input Voltage (VAC)
208/240
Output Voltage (VAC)
120/120
208
240
Max. Output Current (A)
33.3/33.3
52
45
CAUTION
Power Module is factory configured at 208Vac, 60 Hz input and output.
Without transformer, Input and Output of the UPS must always be
the same.
On 11KVA, 10% de-rating for 200/208VAC.
Isolated 120/208/240VAC are available with EX RT Transformer Module.
86-86000-00 B01
Introduction
1—3
EX 5/7/11 RT Systems
Table 1-5: Battery Module Ratings.
1.2
Part Number
86207
86209
Battery Type
12VDC/7Ah
12VDC/9Ah
Battery Output Voltage
240VDC
240VDC
Standard Configuration
The EX 5/7/11 RT systems can be set up in tower or rack configurations.
1.2.1
Tower Configuration
Figure 1-1: Tower Configuration with Power Module, Battery Module, and optional Transformer Module.
EXB RT
EX 11
EX
RT
er
sform
RT Tran
ON
OFF
BATTERY MODULE
POWER MODULE
TRANSFORMER MODULE
1—4
Introduction
86-86000-00 B01
Installation and User Manual
1.2.2
Rack Configuration
Figure 1-2: Rack Configuration with Power Module, Battery Module, and optional Transformer Module.
Standard Configuration
Configuration with Transformer
POWER MODULE
(EX 5/7/11 RT)
sformer
EX RT Tran
EX 11 RT
ON
TRANSFORMER MODULE
POWER MODULE
(EX 5/7/11 RT)
OFF
EXB RT
BATTERY MODULE
(EXB 5/7/11 RT)
BATTERY MODULE
(EXB 5/7/11 RT)
Table 1-6: System Dimensions and Weights.
Model
Dimensions (HxWxD)
Weights
EX 5/7RT Power Module
(3U) 5.16” x 17.49” x 26.25”
(131 x 444 x 667mm)
49.6 lbs (22.5 kg)
EX 11RT Power Module
(3U) 5.16” x 17.49” x 26.25”
(131 x 444 x 667mm)
60.6 lbs (27.6 kg)
EXB 5/7RT Battery Module
(3U) 5.16” x 17.49” x 25”
(131 x 444 x 635mm)
142 lbs (64.5 kg)
EXB 11RT Battery Module
(3U) 5.16” x 17.49” x 25”
(131 x 444 x 635mm)
151 lbs (68.5 kg)
EX RT Transformer Module (11kVA)
(3U) 5.16” x 17.49” x 25”
(131 x 444 x 635mm)
173 lbs (78.5 kg)
CLA Charger Module
(3U) 5.16” x 17.5” x 25
26.5 lbs (12 kg)
EX RT Transformer Module (7kVA)
(3U) 5.16” x 17.49” x 25”
(131 x 444 x 635mm)
173 lbs (78.5 kg)
86-86000-00 B01
Introduction
1—5
EX 5/7/11 RT Systems
1.3
Rear Panel Components
1.3.1
Power Module EX 5/7/11 RT
Figure 1-3: Rear panel of the Power Module.
1
Slot for optional communication cards.
2
2
Dry (relay) contacts Communication Port.
3
3
Remote Emergency Power Off (REPO) function.
1
4
5
(See Section 2.6.)
6
9
10
Connector for automatic detection of Battery Module(s).
5
RS232 communication port.
6
Battery/CLA Module power connector.
7
Manual Bypass switch.
8
Normal AC source circuit breaker.
9
Knockout for entry of AC Output conduit.
10
Knockout for entry of Normal AC source conduit.
11
Knockout for entry of Bypass AC source conduit.
7
8
11
1.3.2
4
Battery Module EXB 5/7/11RT With Remote Emergency Power Off (REPO) Function
Figure 1-4: Rear Panel of the Battery Module.
12
12
Connectors for automatic detection of additional battery
module(s) (to the UPS or to other Battery Modules).
13
Battery power connectors (to the UPS or to other
Battery Modules).
14
Battery Circuit Breaker with shunt trip.
13
14
1—6
Introduction
86-86000-00 B01
Installation and User Manual
1.3.3
EX RT Transformer Module
Figure 1-5: Rear Panel of the optional Transformer Module. (PN 86211/86311)
Load 3: 1 NEMA L6-30R, 208Vac
Load 2: 4 NEMA 5-15/20R, 120Vac
Load 4: 4 NEMA 5-15/20R, 120Vac
Load 3 Circuit Breaker
Load 4 Circuit Breaker
Load 2 Circuit Breaker
Main Output Circuit Breaker
AC Input
Transformer I/O Box
AC Output
Load 1 Circuit Breaker
Load 1: 1 NEMA L6-30R, 208Vac
Transformer Protect
Breaker
1.4
Power Module Display and Control Panel
Figure 1-6: View of typical control panel interface.
15
16
17
18
EX 11 RT
19
OFF
15
Load protected/On-line Operation LED.
16
Operation on battery LED.
17
Operation on bypass LED.
18
Fault LED.
19
LCD display.
20
UPS OFF button.
ON
21
23
20
86-86000-00 B01
21
22
22 Function buttons (scroll up/scroll down).
UPS ON button (or function button in
personalization mode).
23
Introduction
1—7
EX 5/7/11 RT Systems
1.5
Optional Accessories
Optional Accessories describes the options available for upgrades and enhancement of the EX 5/7/11 RT systems.
Detailed installation of the unit is described in following sections.
To ensure a successful installation, all procedures should be followed in their correct sequence. Note that any
unauthorized installation may cause damage to the UPS(s) and void the MGE Office Protection Systems warranty.
1.5.1
Power Module Rail Kit
(Part Number 86001)
This kit is for rack mounting the Power Module in a 19" enclosure. See Section 2.4.3 for rack installation of Power
Module.
Figure 1-7: Power Module Rail Kit.
24
25
27
26
24
Front mounting brackets.
25
Rear support brackets, part number
86013. This can be ordered separately.
26
Telescopic rails, 25.16" to 39.61"
length (639 mm to 1005 mm).
27
Input/Output Box bracket system, part
number 86012.
1.5.2 Battery/Transformer/CLA Module Rail Kit
(Part number 86002)
This kit is for rack mounting of the Battery/Transformer/CLA Module in 19" enclosure. See Section 2.4.3 for rack
installation of module.
Figure 1-8: Battery/Transformer/CLA Module Rail Kit.
24
25
26
1—8
Introduction
24
Front mounting brackets.
25
Rear support brackets, part number
86013. This can be ordered separately.
26
Telescopic rails, 25.16" to 39.61"
length (639 mm to 1005 mm).
86-86000-00 B01
EX 5/7/11 RT Systems
1.5.3
Installation and User Manual
Multiple Battery Module Back-up Time at Full Load
Standard EX 5/7/11 RT systems (one Power Module and one Battery Module), offers a standard back-up time of 5
to 12 minutes at full load.
To increase back-up time, it is possible to connect up to 5 additional Battery Modules to the standard system. See
Section 2.8 for connections between standard system and Battery Module (EXB 5/7/11RT)
Figure 1-9: Typical back-up time with multiple EXB’s at full load.
Optional
Configurations
Standard
EX 5/7/11RT systems
EX 5/7/11RT EXB 5/7/11RT
5 kVA :
7 kVA :
11 kVA:
EXB 5/7/11RT
EXB 5/7/11RT
EXB 5/7/11RT
25 min
20 min
14 min
45 min
32 min
22 min
60 min
45 min
30 min
9 min
7 min
5 min
+ EXB 5/7/11RT + EXB 5/7/11RT
84 min
57 min
42 min
100 min
72 min
53 min
See Appendix for additional Back-up time information.
1.5.4
Battery Extension Cable Kit
(6 ft./1.8 m, Part number 86006)
This extended battery cable kit will be used instead of the standard battery cable when Battery Modules (EXBs) are
distant from each other (located in two different enclosures, for instance).
The battery extension cable kit includes a 6 ft. long, straight connector battery power cable, and a 6 ft. long battery
detection cable.
86-86000-00 B01
Introduction
1—9
EX 5/7/11 RT Systems
1.5.5
Battery Integration Kit with Casters
(Part number 86005)
Battery Integration Kit is a cart, designed to hold up to 8 modules. It has swivel wheels with brakes, leveling feet,
seismic floor mount panels, plates to lock modules and hardware included. Modules not included.
Figure 1-10: Typical Battery Integration kit with casters setup.
TRANSFORMER MODULE
(optional)
POWER MODULE
BATTERY MODULES
(up to 6)
(Modules Not Included In Kit)
1.5.6
Input/Output Box
OFF
O
- I/O Box 5/7kVA Part number 86009
- I/O Box 11kVA Part number 86010
1 — 10
Introduction
86-86000-00 B01
EX 5/7/11 RT Systems
1.5.7
Installation and User Manual
Transformer Module - For use with EX 5/7/11 RT Power Module
This module provides isolated 120/208/240VAC outputs.
Figure 1-11: Typical Transformer Module Contents and Connections.
EX RT Transformer Module Box Contents
EX RT Transformer
Warranty and
Quick Start Manual Product Registration Tower Stand Extenders
w w w. m g e o p s . c o m
EX 5/7/11RT Systems
Quick Start
Transformer
Cable
Stabilizer Bracket
(4 screws included)
Transformer
Rail Kit
41
86-86000-00 B01
Introduction
1 — 11
EX 5/7/11 RT Systems
1.5.8
CLA Charger Module
Extended back-up time (up to 8 hours at full load) requires a high power battery cabinet connected to the EX 5/7/11 RT
via the CLA Module.
IMPORTANT
The CLA can not be used to charge the Battery Module (EXB). It is designed to
charge the customer provided high power battery cabinet.
Figure 1-12: CLA Module Contents and Connections.
CLA Module Contents
CLA Rail Kit
Tower Stand Expanders
CLA Module Quick Start
Battery Power Cable
41
w w w. m g e o p s . c o m
EX
RT
forme
Trans
r
Stabilizer Bracket
(4 screws included)
EX 5/7/11RT Systems
Quick Start
Battery Detection Cable
m
eups.co
www.mg
Optional High Power
Battery Cabinet
CLA
(not included)
EX 5/7/11RT
50A
15A Utility
AC Source
~
(cable not included)
(see section 2.9 for cable
connection information)
(cable w/battery not included)
Table 1-7: Battery back-up time chart.
Total battery voltage : 240 VDC (20 x 12VDC, one string).
Battery Back-up Time
EX 5RT
EX 7RT
EX 11RT
2 hours
50 Ah
65 Ah
100 Ah
4 hours
100 Ah
130 Ah
200 Ah
8 hours
200 Ah
260 Ah
400 Ah
IMPORTANT
1 — 12
Recommended Batteries
The battery capacity must be set within the UPS (5 Ah increment)
See UPS Personalization Section 3.2.
Introduction
86-86000-00 B01
Setup and Installation
2.0
Scope
Setup and Installation guides the user through tools and equipment required for connecting the EX 5/7/11 RT, and
battery installation or replacement. Included are assembly instructions, power cable connections with wire diagrams
for configuring the product to hardware specifications.
2.1
Unpacking and Parts Check
Once the EX 5/7/11 RT systems has been inspected and received from the shipping courier, the unit should be
moved to a position as close to the final installation location as possible. See Figures 2-1, on Page 2 — 2.
All Modules are shipped in separate boxes.
Prior to any installation, the following items should be observed upon receipt of the EX 5/7/11 RT.
1.
Inspect shipment for any damage prior to receipt. Damage claims should be filed directly with the courier.
Replacements for damaged components should be ordered through MGE Office Protection Systems Customer
Support Services at 1-800-438-7373.
2.
Remove wrapping and foam corners to verify that the equipment nameplate (located on the rear of the units)
details a system that corresponds with the equipment ordered.
86-86000-00 B01
Installation
2—1
EX 5/7/11 RT Systems
2.2
Contents of Standard EX 5/7/11 RT Systems
Contents of EX 5/7/11 RT Power Module: (PN 86215 / 86216 / 86217)
30
EX 5/7/11 RT Power Module.
31
Two sets of tower stands.
32
RS232 communication cable.
33
Product documentation.
34
Input/Output Box. (PN 86009 for EX 5/7RT; 86010 for EX 11RT)
35
Solution-Pac 2 CD.
36
Power Module Rail Kit, PN 86001.
IMPORTANT
Packaging must be destroyed according to waste management standards.
Recycling icons are displayed for easy selection.
Figure 2-1: Contents of EX 5/7/11 RT Power Module.
30
31
32
34
OFF
O
EX
11
RT
33
35
36
(see 1.5.1)
- I/O Box 5/7kVA Part number: 86009
- I/O Box 11kVA Part number: 86010
2—2
Installation
86-86000-00 B01
Installation and User Manual
Contents of EXB 5/7/11RT Battery Module: (PN 86207 /86209)
29
Stabilizer Bracket and hardware.
38
EXB 5/7/11RT.
39
Tower stand expanders.
40
Battery Power cable.
41
Battery/EX RT Transformer/CLA Module rail kit, PN 86002.
42
Battery detection cable.
43
EXB Documentation.
44
Bezel hex drive.
Figure 2-2: Contents of EXB 5/7/11RT Battery Module.
38
39
EXB
40
42
RT
29
41
43
44
(not to scale)
- EXB 5RT Battery Module Part number: 86207.
- EXB 7RT Battery Module Part number: 86207.
- EXB 11RT Battery Module Part number: 86209.
86-86000-00 B01
Installation
2—3
EX 5/7/11 RT Systems
2.3
Installation in Tower Configuration
Follow the numerical sequence to assemble tower stands and tower stand expanders, shown in Figure 2-3.
Figure 2-3: Tower Configuration of Standard System and Optional Transformer Module.
Tower Configuration with Standard System
5
EX
EX
11
T
B R
RT
Battery Module
ON
OFF
Power Module
3
4
3
4
4
4
2
1
2
1
Tower Configuration with Optional Transformer Module
Use the same procedure
for tower mounting multiple
battery modules, if applicable.
5
EX
EX
11
T
B R
Battery Module
RT
ON
OFF
Power Module
Transformer Module
3
4
3
4
4
4
2
1
2
1
2—4
Installation
86-86000-00 B01
Installation and User Manual
2.4
Installation in Rack Mounting Configuration
2.4.1
Adjustment of Front Panel Logo and Control Panel for Rack Orientation.
NOTE
If system includes the Transformer Module, we recommend to mount the Battery
Module on the bottom, then mount the Power Module above the Battery Module
and mount the Transformer Module on top for optimum stability.
To prepare the front panel logo and LCD display for rack orientation, of all modules. (including Transformer or CLA
Module, if equipped).
Proceed as follows:
1.
Unclip logo plate and pull the LCD display from front panel.
2.
Rotate them 90 degree counter clockwise as shown.
3.
Place items back onto the panel.
Figure 2-4: Typical Orientation of the Logo and Control Panel. (Power Module Shown)
1 RT
EX 1
EX
11
OFF
RT
ON
OFF
ON
FINISHED PANEL
(rack orientation)
EX
11
OFF
RT
1
1
ON
2
2
1 RT
EX 1
3
86-86000-00 B01
ON
OFF
3
Installation
2—5
EX 5/7/11 RT Systems
2.4.2
Prepare Battery Module for Rack Mounting
IMPORTANT
This step requires two people.
The Battery Module is very heavy (151 lbs.). To ease its rack mounting, you can remove the battery pack from the
Battery Module, as explained below.
Proceed as follows:
1.
Unscrew the six screws securing front panel using Bezel hex driver 44 .
2.
Unscrew the brackets securing the battery connectors.
3.
Disconnect Battery plugs.
4.
Unscrew the brackets securing the battery pack. Remove battery bracket pack covers.
5.
Pull the left and right battery packs out and set aside for reinstalling after the Battery Module cabinet has been
rack mounted.
6.
Mount Battery Module cabinet on rack.
7.
Re-install the battery pack in reverse order.
Figure 2-5: Accessing Battery Pack.
3
3
2
2
RT
EXB
4
1
x6
1
4
1
44
(not to scale)
5
2—6
Installation
86-86000-00 B01
Installation and User Manual
2.4.3
Power, Battery, Transformer, and CLA Charger Module Rack Mounting
The following steps apply to all modules. For simplicity, only Power Module is shown.
Proceed as follows:
1.
Attach both front mounting ear brackets 24 to module with supplied screws. (For this step, it is possible to
adjust the position of both front mounting brackets.)
2.
Attach rear support brackets 25 to module. These brackets prevent the module from sliding out of the rack.
3.
Attach rails 26 together, secure with wing nuts, and finger tighten. (both sides).
4.
Attach both rails to rear and front of rack with supplied flathead screws (as shown).
5.
Use caution when sliding unit into rack. Temporarily secure unit to rack with thumb screws on front mounting
brackets.
6.
Secure rear support brackets to rails.
Figure 2-6: Rack mounting of the Power Module onto the rails.
4
4
3
4
2
4
1
2
4
1
5
4
6
6
6
86-86000-00 B01
6
Installation
2—7
EX 5/7/11 RT Systems
NOTE:
This step is unique to the Power Module. It involves the installation of the I/O Box
Bracket System.
The I/O Box bracket system keeps the I/O Box stationary while hot swapping the Power Module. It will then be
easier to slide the replacement module into the connectors of the I/O Box.
1&2.
Secure small brackets to larger bracket from the underside 27 .
3.
Secure small attached brackets to the I/O Box with four screws.
4.
Secure large bracket 27 to rails at the rear of module with four nuts.
Figure 2-7: Input/Output Box Bracket System.
1
2
3
OFF
4
Install input/output cables
per section 2.7 prior to this step.
4
2—8
Installation
86-86000-00 B01
Installation and User Manual
2.5
Communication Ports
EX 5/7/11 RT Power Module provides 3 communication method's that can be used simultaneously:
◗ A female DB9
Transfer (SHUT)
5
provides RS232 communications using MGE Office Protection Systems Serial HID UPS
protocol. This COM Port is compatible with Solution Pac 2 to perform graceful shutdown.
◗ The Dry Contact Port
2
is used for basic signaling or for protection of IT systems like IBM iSeries
(formerly AS400) and more.
◗ The slot
1 is compatible with most MGE Office Protection Systems Transverse communication card (See
Section 2.5.3 or check www.mgeops.com for the complete list of compatible cards).
2.5.1
Connecting the RS232 Communication Port
1.
Connect the RS232 32 communications cable to the serial port on the computer.
2.
Connect the other end of the communications cable 32
EX 5/7/11 RT.
to the RS232
5
communications port on the
The EX 5/7/11 RT systems can now communicate with Solution Pac 2 for power management. UPS configuration
settings are done by Personal Solution Pac for Windows or through the LCD screen on the front panel (See
Section 3.2).
Figure 2-8: RS232 Communication Cable Connection.
32
1
5
86-86000-00 B01
2
Installation
2—9
EX 5/7/11 RT Systems
2.5.2
Connecting the Dry (Relay) Contact Communication Port
2
The system status is indicated by the connection of common pin (Pin 5) to the appropriate pins. Refer to the pin
explanations below for details.
Figure 2-9: Relay Pin Connections for Communication Port.
Pin 1, 2: not used.
5
4
9
NC
NO
3
8
NO
2
7
1
6
NO
NO
common
Pin 3:
Remote Power Off signal (5 to 27 VDC, 10 mA max).
Pin 4:
Operation on mains (not on battery). (48VDC, 2A max.)
Pin 5:
User common.
Pin 6:
Operation on automatic bypass.
Pin 7:
Low battery.
Pin 8:
Load protected
Pin 9:
Operation on battery.
Legend:
When the status is active, the contact between
the common (Pin 5) and the relevant information
pin is closed.
2.5.3
NO:
contact normally open.
NC:
contact normally closed.
Installation of Optional Transverse Card
It is not necessary to shut down the UPS to install the optional communications card, except for USB card. Following
is a typical installation of the Transverse card (optional Network Management card PN 66074 is shown below).
Proceed as follows:
1.
Remove the slot cover secured by two screws.
2.
Insert the Transverse card into the slot
3.
Secure the card with both screws.
4.
Refer to user manual of the Network Management Card for set-up.
1 .
Figure 2-10: Communication Card Slot with Network Management Card installed.
1
2 — 10
Installation
86-86000-00 B01
Installation and User Manual
A wide range of optional cards will allow your UPS to talk to nearly all equipment management systems, making
integration faster and easier. All these cards can plug directly into the UPS, saving time and money on your next
UPS project. (Meta UPS Card and U-Talk/Basic Acquisition Cards are used exclusively with Multi-slot.)
Dual U-Talk/Basic Card
(PN: 66060) CAN NOT BE USED WITH THIS UPS.
JBus Card
(PN: 66061) Provides RS232 and RS485 connections for using the JBUS/ModBus
protocol. Both connections are female DB9. Only one connector can be used for
proper operation.
Dual port SHUT Card
(PN: 66066) Has two independent female DB9 communication ports that use Serial
HID UPS Transfer (SHUT) protocol. Used with the UPS Control LCD display.
USB Card
(PN: 66067) For direct communications (via USB) with the customer’s server and
automatic UPS recognition by the power management software of Windows 2000,
XP or 2003 Server, or Macintosh OS 9 and 10.
Dual port AS/400 Relay
Status Card
(PN: 66068) CAN NOT BE USED WITH THIS UPS.
6 Alarm Relay Card
(PN: 66069) Provides status in the form of 6 Alarm relays (250V 2A rated relays).
Connection provided are 12 terminal block wire clips.
XML-Web Card
(PN: 66073) Features a web interface and keeps log files about UPS operation.
Network Management Card (PN: 66074) Features a web interface, Simple Network Management Protocol
(SNMP), Simple Mail Transfer Protocol (SMTP) email notification and keeps log files
about UPS operation.
Environmental Sensor
86-86000-00 B01
(PN:66846) For Network Management Card: Monitors temperature, humidity, and
status of 2 dry contact inputs.
Installation
2 — 11
EX 5/7/11 RT Systems
2.6
Remote Emergency Power Off (REPO) Communication Port
3
The end user is responsible for the installation of a Remote Emergency Power Off function. Installation must be
carried out in compliance with local code regulations.
To shutdown the entire system completely in case of emergency:
◗ Disconnect the AC input to the Power Module by opening up the upstream circuit breaker connecting the
utility power to the Power Module.
◗ Turn off the circuit breaker of the Battery Module connecting to the Power Module.
◗ Turn off the circuit breaker of the subsequent Battery Modules, if applicable.
All these steps above should be performed via a single device.
To simplify the last two steps, the Power Module provides an RJ-11, six contact connector on the back panel, called
Remote Emergency Power Off (REPO) port. Upon applying a voltage source (5-27VDC, 10mA max.) to pins 2, 4 of
this port, the Power Module will send a signal to trip off the shunt trip on each circuit breaker of all Battery Modules
via the battery detection cable simultaneously. Refer to the diagram below for details.
Figure 2-10a: Activation of Remote Emergency Power Off function using a contact normally open switch.
RJ 11
3
Connections provided by user.
654321
+
5VDC to 27VDC
10mA (max.)
_
Figure 2-10b: Activation of Remote Emergency Power Off using a contact normally closed switch.
RJ 11
3
Connections provided by user.
654321
5VDC to 27VDC
10mA (max.)
2 — 12
+
_
Installation
86-86000-00 B01
Installation and User Manual
2.7
System Connections
WARNING
This type of connections must be carried out by qualified electrical personnel.
Before carrying out any connections, check that battery circuit breaker 14
is OFF and that the upstream protection devices (Normal and Bypass AC
sources) are open (OFF/OPEN).
2.7.1
Connections with Common Normal and Bypass AC Sources (Single Mains)
Figure 2-11: Power Module I/O Box Terminal Block Diagram.
Bypass AC source
200/208/220/230/240Vac
Output
200/208/220/230/240Vac
Normal AC source
200/208/220/230/240Vac
L6
L5
L2
L1
L1
L4
L3
Terminal tightening torque:
– 18 lb-in. for EX 5/7RT Power Module
– 35 lb-in. for EX 11RT Power Module
Terminal block capacity:
- Max. 4AWG (EX 11RT)
- Max. 6AWG (EX 5/7RT)
NOTE
Jumper
(see note)
◗ The Power Module is factory configured for single input, whereas both Normal
AC and Bypass AC sources are identical, by means of jumper between L1 and L3.
◗ Jumper must be removed for separate Normal AC and Bypass AC sources
(2 Mains) or with Frequency Converter application.
◗ Keep Manual Bypass Switch
86-86000-00 B01
7 at Normal position.
Installation
2 — 13
EX 5/7/11 RT Systems
Proceed as follows:
1.
For normal AC input, make connections to L1, L2, and
terminals only. No connections are required for
Bypass AC input. Make connections to , L5, L6 terminals for output.
CAUTION:
Always connect the earth ground wire first.
Jumper must be between L1 and L3. System is factory configured for 208VAC
output.
2.
Attach I/O Box to the Power Module with three screws.
Figure 2-12: Normal AC Input and Output Cables Installation.
Power Module I/O Box
Output
200/208/220/230/240Vac
Bypass AC source
200/208/220/230/240Vac
Normal AC source
200/208/220/230/240Vac
L6
L5
L2
L1
L1
L4
L3
OFF
O
1
Normal AC Input
Output
Jumper
From Utility
208 VAC
To Load
208VAC
2
10
100
Reset
1 2
ON
IP=
MAC=00E0D8FF855E
RS232 Download
ETHERNET
UPS
data
Card Settings
66074
OFF
O
Output to Load
or
Transformer Module
(if applicable)
Simplified Connection Diagram
UPSTREAM
CIRCUIT
BREAKER
AC INPUT
2 — 14
(NOT SUPPLIED)
Bypass AC
Normal AC
To Load or
Transformer Module
(if applicable)
Installation
86-86000-00 B01
Installation and User Manual
2.7.2
Connecting EX RT Transformer Module
Part number 86211/86311
This module is to provide isolated 120/208/240 VAC outputs to the protected loads.
Figure 2-13: View of EX RT Transformer Module connected downstream for 120/208/240 Vac outputs (shown
with one EXB).
BATTERY MODULE
EXB 5/7/11 RT
POWER MODULE
EX 5/7/11 RT
Transformer Module I/O Box
L3
L2
L1
Lb
Ld
N
Lc
La
TRANSFORMER
MODULE EX RT
AC Input from
Power Module
(208VAC shown)
AC NORMAL
INPUT TRANSFORMER MODULE
OUTPUT TO LOAD
WARNING
AC Output to Load
(120VAC shown)
To avoid overloading 120VAC output windings, distribute loads evenly
between Load 2 and Load 4 (on rear of Transformer Module) and between
120VAC output terminals (Lb-N, La-N.)
Terminal Block Transformer Module Connection diagram
(located on bottom of Transformer I/O Box)
L3
L2
L1
Lb
Ld
N
120VAC
208VAC
Lc
120VAC
La
Terminal Block capability:
AWG 4 solid or stranded wire.
208VAC
240VAC
240VAC
AC Output
AC Input
Simplified Connection Diagram
UPSTREAM
CIRCUIT
BREAKER
Bypass AC
Transformer Module
(NOT SUPPLIED)
AC INPUT
To Load
Normal AC
86-86000-00 B01
Installation
2 — 15
EX 5/7/11 RT Systems
2.7.3
Connections with Separate Normal and Bypass AC Sources (2 Mains)
CAUTION:
This connection requires isolation Transformer Module. Please visit our web site
www.mgeops.com or call (800) 279-7776.
Figure 2-14: Normal AC and Bypass AC inputs, Output Cables Installation, and Simplified Connection Diagram.
Proceed as follows:
1
OFF
O
L1
L3
1.
Remove the cover plate under the I/O Box. Loosen the terminal blocks
L1 and L3, and remove the jumper.
CAUTION:
2
OFF
O
Always connect the earth ground wire first.
2.
Install Normal AC, Bypass AC and output cables as shown.
3.
Reinstall the cover plate under the I/O Box with four screws.
4.
Secure the I/O Box to the Power Module with three screws.
See Section 2.7.2 for connecting EX RT Transformer module, if applicable.
Bypass
3
Output
4
Normal
UPS
data
10
ETHERNET
100
Reset
1 2
ON
RS232 Download
IP=
MAC=00E0D
8FF855E
Card Settings
66074
OFF
O
To Load or
Transformer Module (if applicable)
With separate Normal and Bypass AC inputs, supplied by separate sources.
BYPASS AC
MAINS 2
Isolation
Transformer
(PN 86211)
LOAD
MAINS 1
NORMAL AC
2 — 16
NOTE:
Please visit our web site www.mgeops.com or call (800) 279-7776 for assistance
with separate, normal AC, and bypass AC input support.
NOTE:
With parallel redundance connection, two input transformers are needed for
separate, normal, and AC bypass input. Please visit our web site
www.mgeops.com for details.
Installation
86-86000-00 B01
Installation and User Manual
2.7.4
System Connections as Frequency Converter (without Bypass AC source)
Figure 2-15: Accessing Terminal Blocks for Input and Output Power Cables.
CAUTION:
1.
Always connect the earth ground wire first.
Remove the cover plate under the I/O Box.
OFF
O
Remove the jumper connecting L3 and L1.
CAUTION:
1
Removing the jumper will disable the Bypass AC
source. Do not connect anything to the Bypass AC
terminal block.
2.
Refer to Section 2.7.1 to install Normal AC source and output wires per
I/O Box Terminal diagram. Re-install the cover plate under the I/O Box.
3.
Secure the I/O Box to Power Module with three screws.
See Section 2.7.2 for connecting EX RT Transformer Module, if
necessary.
Power Module I/O Box
Output
200/208/220/230/240Vac
Bypass AC source
200/208/220/230/240Vac
Normal AC source
200/208/220/230/240Vac
L
L5
L2
L1
1
L4
L3
OFF
O
1
Normal AC Input
Jumper
Output
INPUT
From
Utility
208 VAC
OUTPUT
To Load
208VAC
2
10
100
Reset
1 2
ON
IP=
MAC=00E0D8FF855E
RS232 Download
ETHERNET
UPS
data
Card Settings
66074
OFF
O
Output to Load
or
Transformer Module
(if applicable)
86-86000-00 B01
Installation
2 — 17
EX 5/7/11 RT Systems
2.8
Connection of Battery Module EXB
1.
Check that the battery circuit breaker (5) 14 is OFF (“0”) position.
2.
Connect the battery power cable 40 to the connectors
3.
Connect the battery detection cable 42 between connectors
Modules.
6
and 13 of the Power and Battery Modules.
4
and 12 of the Power and Battery
Figure 2-16: Rear view of Battery Module cable connections.
12
4
42
40
13
6
14
2 — 18
Installation
86-86000-00 B01
Installation and User Manual
2.9
Connection of Optional CLA Module
1.
Connect the battery power cable 40 and battery detection cable 42 (provided with the CLA Module)
between the Power Module and the CLA Module.
2.
Connect the DC Input of the CLA Module to high power battery cabinet.
3.
Connect the utility AC input to terminal blocks L1 and L2 of the CLA.
◗ DC Input Cable cross-section (not provided): maximum 4 AWG solid or stranded wire.
◗ AC input cable cross-section (not provided): maximum 16 AWG solid or stranded wires.
Field wiring connections to terminal block shall be made using the following:
– No. 14 AWG, 60ºC copper wires for AC inputs.
– No. 10 AWG, 75º C copper wires for DC inputs.
Figure 2-17: Rear view of CLA Module cable battery and AC input connections
Connection Diagram
(inside CLA Module)
42
-
+
DC INPUT
240Vdc
N
(L2)
L
(L1)
AC INPUT
40
156-280Vac
Terminal tightening torque:
– 5 lb-in. for AC input terminals
– 18 lb-in. for DC input terminals
DC Input to
High Power
Battery Cabinet
Separate, 15A Utility
AC Source
@ 208 or 240
Use 15A DBL. Pole CB
86-86000-00 B01
Installation
2 — 19
EX 5/7/11 RT Systems
(This page left blank intentionally)
2 — 20
86-86000-00 B01
Operation
3.0
Scope
Operation describes EX 5/7/11 RT systems characteristics of indicators and controls, modes and specifications and
theory of operating the EX 5/7/11 RT. The user procedures include performing software programming that will
maintain smooth performance. Refer to Figure 1.6 for descriptions of circled numbers.
3.1
Initial Startup
NOTE
Both AC and DC sources must be present for normal startup of EX 5/7/11 RT
systems. If the system is configured for cold start, the AC and DC sources are
required for initial startup only.
7
1.
Check that the manual bypass switch
is on Normal position.
2.
Set the Normal AC source circuit breaker
3.
Set the battery circuit breaker 14 to the ON position.
8
to the ON position.
The load is powered via the Bypass AC source, but not protected by the UPS.
Batteries are recharging, an eight-hours recharge period is necessary to get full back-up time.
LED 17 is ON.
Figure 3-1: Initial Startup Display.
17
OFF
86-86000-00 B01
ON
Operation
3—1
EX 5/7/11 RT Systems
3.2
UPS Personalization
WARNING
Before changing items from Tables, 3-1, 3-2, 3-3, and 3-4, the UPS system
must be turned OFF.
IMPORTANT
If specific settings are required, it is recommended to enter the UPS
personalization mode at this stage.
It is possible to enter this mode through the front panel buttons or the
Solution-Pac 2 software for Windows included in the MGE Office Protection Systems
Solution-Pac 2 CD-ROM.
3.2.1
Accessing personalization with front panel buttons
◗
Press "scroll down" 21 and "scroll up" 22 function buttons together for more than 3 seconds.
◗
Press the function button 22 placed under the “ENT” word to enter the set up mode and follow the LCD
messages using the buttons now defined as select keys. See Tables: 3-1, 3-2, 3-3, and 3-4 for settings.
Figure 3-2: Control Panel with scroll up and down buttons.
UPS SET UP
EXIT ENT
OFF
ON
21
3—2
22
Operation
86-86000-00 B01
Installation and User Manual
Table 3-1: Local Settings.
Display
Factory setting
Options
Language
English
French, Spanish, German, Italian
Date/time format
International
US
Date/time change
(DD-MM-YYYY/HH:MM)
MM-DD-YYYY/HH:MM adjustable
Audible alarm
Quick beeps
Slow beeps
Table 3-2: Output Features.
Display
Factory setting
Options
Comments
Output voltage
208 Volts AC (***)
200/208/220/230/240/250
Input voltage must be equal to
output voltage
Frequency converter
Disabled
Enabled
Bypass AC source disabled
Output frequency
Auto ranging
50/60 Hz
User selectable under
frequency converter mode
ECO mode
Disabled
Enabled
See Section 3.4.2.
Hot standby
Disabled
Enabled
Cascade (See Figure 3-3)
Operating mode
Industrial
IT Network
(*) See Table 3-5.
Bypass
Transfer
When bypass NOK
When bypass OK (**)
(*) See Table 3-5.
Interrupt time
10 ms
10 to 200 ms
(by steps of 10 ms)
Interrupt time calibration during
during load transfer when
Bypass AC source
is out of tolerances
Overload level
102%
50/70%
(*) : - Select "IT Network" for computer loads. Select “Industrial” for other applications or when there exists and absolute need
for service continuity (with potential 10msec. interrupt) when Bypass AC source is not within set tolerances.
See Table 3-5 for more details.
(**) UPS will switch to Bypass AC Source if it is within the set tolerances.
(***) Input voltage must be equal to output voltage.
Figure 3-3: Configuration used to provide cascade redundancy to critical loads.
BYPASS AC
Cascade redundancy configuration
offers better protection to critical
load, whereas the first UPS acts as
the Bypass AC Source for the
second UPS.
Protective Device
NORMAL AC
Utility
AC Source
Protective Device
NORMAL AC
LOAD
86-86000-00 B01
Operation
3—3
EX 5/7/11 RT Systems
Table 3-3: ON/OFF Features.
Display
Factory setting
Options
Comments
Cold start
Disabled
Enabled
Start on battery.
Forced reboot
Enabled
Disabled
UPS restarts automatically
when normal AC source
is restored.
Automatic restart
Enabled
Disabled
UPS restarts automatically
when normal AC source
is restored.
Sleep mode
Disabled
Enabled
Automatic shutdown on battery
if output load level <10%
Remote Command
Enabled
Disabled
Enables shutdown or restart
orders from software.
Comments
Table 3-4: Battery Features.
Display
Factory setting
Options
Battery test
Every week
No test/daily/monthly
Pre-Alarm
20%
0 to 100%
Low battery signal;1% increment
Runtime choice
UPS reads # and type
of Battery Modules
connected.
From 50 to 400 Ah
Requires CLA Module if using
options (See Section 1.5.8)
Battery deep discharge
protection
Enabled
Disabled
If disabled, loss of
MGE Office Protection Systems
warranty.
3—4
Operation
86-86000-00 B01
Installation and User Manual
3.3
Information Technology IT Network and Industrial Operating Modes
Table 3-5: System Operation in IT Netowrk and Industrial Modes.
Symptoms
IT Network mode
Industrial mode
Overload, and Bypass
source in tolerance.
Load is transferred to Bypass AC source.
UPS returns to normal mode if overload
is removed.
Same as IT Network mode, but AC
to the UPS does not return to
normal mode if overload
is removed.
Overload, and Bypass
AC source not in tolerance.
The UPS shuts down and load is not
transferred to Bypass AC source.
Load is transferred to Bypass
AC source with 10 milliseconds output break.
The UPS does not return to
normal mode if overload
is removed.
Load is transferred to Bypass
AC source. The UPS does not
return to normal mode if the
short circuit is removed.
Output short circuit and Bypass The load remains powered by the UPS.
AC source in tolerance.
The UPS shuts down after 3 minutes
if the short circuit remains.
Output short circuit and Bypass The load remains powered by the UPS.
AC source not in tolerance.
The UPS shuts down after 3 minutes
if the short circuit remains.
86-86000-00 B01
Operation
The load is transferred to
Bypass AC source with
10 milliseconds output break.
The UPS does not return to
normal mode if the short circuit
is removed.
3—5
EX 5/7/11 RT Systems
3.3.1
UPS personalization through external software
Insert the Solution-Pac 2 CD ROM in your CD drive.
◗
At the first Navigator Screen, select "Installation" and follow the instructions to install
Solution-Pac 2 for Windows.
◗
If nothing appears, launch startup.exe
◗
Then go to "Advanced settings" and "UPS settings".
Please note that the Linux/Unix/MacOS versions of Personal Solution-Pac do not include this feature.
3.3.2
Final Startup sequence
Press the <ON> button more than 3 seconds.
◗
After UPS internal test sequence, the green LED 15 goes on.
CAUTION
3—6
During the startup, if the Bypass AC source is out of tolerance, there
will be a 10msec output interrupt.
Operation
86-86000-00 B01
Installation and User Manual
3.4
Operating Modes
3.4.1
Normal (Double Conversion) Mode
Figure 3-4: Normal (Double Conversion) Mode.
15
This is the standard operating mode, set by the
factory.
Two possible cases.
1.
LOAD LEVEL
4kW / 5 kVA
OFF
15
15 LED is ON.
The load is protected by the UPS.
ON
21
If Normal AC source available:
Scroll down 21 or scroll up 22 function buttons
allow you to read the UPS measurements (Normal
AC source voltage, Bypass AC source voltage,
operating mode, battery capacity and UPS Serial
Number).
22
16
2.
If Normal AC source not available:
CAUTION:
REMAINING TIME
10 minutes
OFF
Do not operate the Manual
Bypass switch when the UPS is
in Normal mode.
15
LED flashes.
16
LED is ON.
ON
The audible alarm sounds intermittently.
The load is now powered by the UPS battery.
This display shows remaining back-up time.
86-86000-00 B01
Operation
3—7
EX 5/7/11 RT Systems
3.4.2
ECO Mode
Figure 3-5: ECO Mode Display.
15
The main advantage of the ECO mode is that it
reduces the consumption of electrical power by not
running in the online mode. When this mode is
selected, the system works as an offline UPS
system, powered by Bypass source if Bypass source
is inside user’s defined range. Outside this range,
the UPS system will switch to online mode with 10ms
interrupt.
17
OFF
Three possible cases:
ON
1.
If Normal AC source (Mains 1) and Bypass AC
Source (Mains 2) are available:
15 and 17 LED are ON.
15
The load is supplied with AC power but not protected
in ECO mode.
2.
If Normal AC source (Mains 1) is available, but
Bypass AC source (Mains 2) is not available:
15 LED is ON.
OFF
ON
The audio alarm sounds intermittently.
The load is automatically supplied in Normal mode
via the Normal AC input.
15
16
3.
Both Normal and Bypass AC sources not
available or out of tolerance:
15 LED is ON.
16 LED is ON.
The audio alarm sounds intermittently.
OFF
ON
The load is powered by the battery power from
the UPS.
The LCD display indicates the battery remaining
back-up time.
3—8
Operation
86-86000-00 B01
Installation and User Manual
3.5
Operation on Battery Power
Figure 3-6: Transfer, Threshold and End of back-up time.
15
3.5.1
16
Transfer to Battery Power
The load continues to be protected by the UPS when
the Normal AC source is not available. Power is
supplied by the battery.
There are three possible cases:
REMAINING TIME
10 minutes
First Case: Operation on battery
15
LED is ON.
16
LED is ON.
ON
OFF
The audio alarm beeps every 10 seconds.
15
16
◗
This indicate the load is supplied by the battery.
◗
The LCD display indicates the battery remaining
back-up time.
Second Case: Low battery warning
REMAINING TIME
2 minutes
OFF
ON
15
LED is ON.
16
LED flashes.
The audio alarm beeps every 3 seconds.
◗
15
Low battery warning on LCD display. There is
very little remaining battery back-up time. Close
all applications because UPS automatic
shutdown is pending.
16
Third Case: End of back-up time
OFF
86-86000-00 B01
ON
15
LED is OFF.
16
LED is OFF.
The audio alarm is stopped.
Operation
3—9
EX 5/7/11 RT Systems
3.6
Return of Normal AC source
After an outage, the UPS restarts automatically when AC power is restored (unless this function has been disabled
via UPS personalization).
3.7
Shutdown
Figure 3-7: Shutdown Display, Circuit Breaker, and AC Source Switch.
1.
17
Press the OFF button 20 more than 3 seconds.
CAUTION: The load is no longer protected by
the UPS. It is powered via the
Bypass AC source. If the UPS is set
in frequency converter mode, the
load will not be powered.
OFF
If the Bypass AC source is out of
tolerance, the UPS will generate a
calibrated 10msec output interrupt.
ON
20
14
2.
Set the battery circuit breaker(s) 14 to the OFF
position.
3.
Set the Normal AC source circuit breaker
8
to
the OFF position.
LED 17 is now OFF.
CAUTION: Performing this step will disconnect
power to the load.
8
4.
3 — 10
Operation
For the complete shutdown of the UPS (no input
and output power), the upstream circuit breaker
(not included) should be set to the OFF position.
86-86000-00 B01
Maintenance
4.0
Scope
Maintenance includes a troubleshooting guide of symptoms and possible solutions, hot swapping the Power Module
and Battery Module, and testing scenarios.
4.1
Troubleshooting
◗
If any of LEDs 17 or 18 is on, there is an operating anomaly or an alarm.
◗
Use "scroll up" or "scroll down" function button to reset the audible alarm.
Table 4-1: Troubleshooting Not Requiring MGE Office Protection Systems After-Sales Support.
Symptoms
Indication
Correction
LED 17 is on, and Bypass
AC source is present
the LCD display shows
BAD CONNECTION
REWIRE AC NORMAL
AC source is not connected
to the correct terminals.
Rewire correctly to the Normal AC
source.
LED 17 is on,
the LCD display shows:
LOAD LEVEL
XX kW / XX KVA
Load supplied by Bypass AC source.
Push the ON button for more than
3 seconds.
LED 17 is on, and Bypass
AC source is present
the LCD display shows:
THERMAL OVERLOAD
1XX%
UPS overload
Check if any device is shorted or
failed.
LED 18 is on, the LCD
display shows:
CURRENT OVERLOAD
Short circuit conditions on output
devices.
Check if any load has shorted or
failed.
LED 15 is on, but
the LCD display shows:
BYPASS REVERSE
REWIRE BYPASS
180° degree phase shift between
bypass and normal AC source.
Check if Bypass source is correctly
wired
(in case of upstream transformer use).
Audible alarm is on,
the LCD display shows:
I/O BOX REMOVED
Input/Output box not
installed correctly.
Check if the Input/Output box
is correctly installed. See Section 2.7.
Check for correct I/O Box.
86-86000-00 B01
Maintenance
4—1
EX 5/7/11 RT Systems
Table 4-2: Troubleshooting Requiring MGE Office Protection Systems After-Sales Support.
Symptoms
Indication
Correction
LED 17 and 18 are on,
Bypass AC Source is present
and audible alarm is on.
the LCD display shows:
xxx FAULT
Internal fault
and transfer of load
on Bypass AC source
Please visit www.mgeops.com
or call (800) 279-7776 for technical
support
LED 17 is on, and
audible alarm is on,
the LCD display shows
BATTERY FAULT
Battery fault during the battery test.
Follow the battery replacement
procedure in Section 4.4.
LED 17 is on,
the LCD display shows:
SHUTDOWN
STATIC SW FAILED
Static switch failure
Please visit www.mgeops.com
or call (800) 279-7776 for technical
support
Audible alarm is on,
the LCD display shows:
BATTERY CHECK
Batteries may have exceeded
their rated life period. Battery
capacity is severely reduced.
Follow the battery replacement
procedure in Section 4.4.
NOTE: To reset the alarm permanently, press both function buttons 21 and 22 for more than 3 seconds.
4—2
Maintenance
86-86000-00 B01
Installation and User Manual
4.2
Hot Swapping the Power Module
This operation can be performed without interrupting the load.
Figure 4-1: Disconnecting the Power Module.
17
1.
Check if UPS is on Bypass AC source by verifying
that:
XXX FAULT
1CXXXXXXX
OFF
LED 17 is ON (If LED 17 is not ON, do not
turn the manual bypass and visit
www.mgeops.com or call (800) 279-7776.
ON
20
Card
5E
8FF85
IP= 00E0D
MAC=
10
100
Settin
2
RS23
6607
7
2.
Turn the manual bypass switch
BYPASS position.
3.
Switch the battery circuit breaker(s) 14 to the
OFF position.
gs
UPS
data
Stop the system with the OFF button 20 (press
more than 3 seconds). System is now powered by
Bypass AC source.
4
to the
Reset
1 2
ON
RS23
RNET
ETHE
load
2 Down
42
CAUTION: Do not switch the Normal AC
source circuit-breaker 8
to the OFF position.
Doing so will disconnect
power to the load.
40
7
φ
8
4.
Loosen three screws to remove the
Input/Output box.
5.
Disconnect the battery cables 40 and 42 from
the Power Module.
Step 4 in Tower
configuration
The Power Module can be replaced.
The connected equipment is powered by the
Bypass AC source.
Step 4 in Rack
configuration.
86-86000-00 B01
Maintenance
4—3
EX 5/7/11 RT Systems
4.3
Re-Connecting the Power Module
This operation can be performed without interrupting the load.
Figure 4-2: Reconnect the Power Module.
15
17
1.
Secure the Input/Output box using the three
screws.
2.
Reconnect the cables 40 and 42 to the
Power Module.
LOAD LEVEL
4 kW/ 5 kVA
OFF
ON
3.
Switch the battery circuit breaker(s) 14 to the
ON position.
4.
Check if Normal AC source circuit breaker
8
is on the ON position.
23
5.
Check that the LED 17 is ON.
6.
Turn the manual bypass switch from the
BYPASS to the NORMAL position.
7.
Follow initial start up sequence (See Section 3.1)
in order to personalize the UPS.
8.
Push the ON button 23 for more than 3
seconds.
The green LED 15 is ON, and the connected
equipment is now protected by the UPS.
4—4
Maintenance
86-86000-00 B01
Installation and User Manual
4.4
Hot Swapping the Battery Module
During the replacement of the Battery Module, it is imperative to use the same type and number of element as the
original Battery Module provided with the UPS to maintain an identical level of performance and safety. In case of
doubt, please refer to our web site at www.mgeops.com or call (800) 279-7776.
Figure 4-3: Rear View of the Battery Module.
4.4.1
Battery Module
42
Power Module
40
Disconnecting the Battery Module
1.
Switch the battery circuit breaker(s) 14 to the
OFF position.
2.
Disconnect the cables 40 and 42 from the
Power Module.
The Battery Module can be replaced.
The connected equipment is powered by the UPS,
but not protected.
It is also possible to replace the battery packs
instead of Battery Module.
CAUTION:
Always replace both
battery packs with
new ones.
To remove battery pack:
1.
First, switch the battery circuit breaker(s) to the
OFF position.
See Section 2.4.2 and follow instructions for battery
pack replacement.
14
86-86000-00 B01
4.4.2
Re-Connecting the Battery Module
1.
Reconnect the battery cables 40 and 42 to
the Power Module.
2.
Switch the battery circuit breaker(s) 14 to the
ON position.
Maintenance
4—5
EX 5/7/11 RT Systems
(This page left blank intentionally)
4—6
86-86000-00 B01
Appendix
5.0
Electrical Specifications
Electrical and Mechanical specifications for the EX 5/7/11 RT.
5.1
System Input/Output Power Ratings
Table 5-1: EX 5/7/11 RT Voltages and Frequency Characteristics.
Source
Voltage
Frequency
Normal AC Source
Bypass AC Source
Load Output
156 to 280 VAC
40 to 70 Hz
160 to 242 VAC*
58 to 62 Hz**
200/208/220/230/240/250VAC
50/60 Hz autoranging
(120/208/240Vac
(or frequency converter)
are possible with
transformer module)
(*): depends on output voltage setting, can be modified by software.
(**): set to +/- 4% by default, (1, 2, 4, 8% are possible values), can be modified by software.
5.2
System Overload Characteristics
Figure 5-1: Power Supplied as a Function of Input Voltage (Left), and Permissible UPS Overloads as a Function of
Time (Right).
Load Percentage
100%
70%
U
120V 160V
280V
Load Percentage
1.5
1.25
1.1
1.02
0.5s
86-86000-00 B01
t
30s
60s
120s
Appendix
5—1
EX 5/7/11 RT Systems
5.3
System Back-Up Characteristics
Table 5-2: Back-Up Time (In Minutes).
11kVA With 9Ah Battery Modules:
Standard
Std + 1 EXB
Std + 2 EXB
Std + 3 EXB
Std + 4 EXB
Std + 5 EXB
10%
90
191
293
392
525
637
20%
40
93
143
199
261
312
30%
25
61
96
135
172
201
40%
18
43
71
99
120
142
50%
14
30
53
84
102
113
60%
11
24
44
60
86
102
70%
9
20
34
51
67
87
80%
7
17
27
43
56
68
90%
6
15
24
35
48
60
100%
5
14
22
30
42
53
20%
57
125
203
244
364
453
30%
37
80
124
185
245
287
40%
28
61
101
128
169
232
50%
21
53
83
108
132
164
60%
15
37
66
90
110
133
70%
12
30
55
75
98
118
80%
10
24
45
61
77
102
90%
8
22
38
53
69
86
100%
7
20
32
45
57
72
40%
33
84
120
170
235
260
50%
25
60
100
122
170
225
60%
21
46
75
110
135
170
70%
16
39
64
95
119
140
80%
13
31
57
84
105
120
90%
11
27
52
68
92
110
100%
9
25
45
60
84
100
7kVA With 7Ah Battery Modules:
Standard
Std + 1 EXB
Std + 2 EXB
Std + 3 EXB
Std + 4 EXB
Std + 5 EXB
10%
121
266
447
578
756
889
5kVA (US Model Only) with 7Ah Battery Modules:
Standard
Std + 1 EXB
Std + 2 EXB
Std + 3 EXB
Std + 4 EXB
Std + 5 EXB
5.4
10%
170
358
540
740
892
1220
20%
91
170
260
355
505
540
30%
49
110
170
240
290
355
System Short Circuit Protection
Short circuit current provided by EX 5/7/11 RT in normal or battery mode:
EX 5/7RT
110A for 80ms
EX 11RT
150A for 80ms
5.5
Accessories Electrical Characteristics
EX RT Transformer Module
5—2
Nominal power
Nominal current
Input voltage
Output Voltage
Frequency
Isolation (EN 61558-1-2-4)
Operating temperature
Max. operating rel. humidity
Derating/altitude
11 kVA, 7 kVA
63 A, 35 A
208-240Vac
120/208/240Vac
50/60 Hz (+/-10%)
3.75 kV / 5 M ohms
From 0° to +40°C
95%
Pn-10% > 1000 m
EX RT CLA Module
AC input voltage
Input frequency
Battery charge current
156-280 Volts AC
40-70 Hz
6 A DC
Appendix
86-86000-00 B01
Installation and User Manual
Table 5-3: Battery Recharge Time to Recover 90% of the Rated Back-Up Time After Discharge at Full Load.
Configuration for
2 hours back-up time
Configuration for
4 hours back-up time
Configuration for
8 hours back-up time
7 hours
15 hours
24 hours
EX 7RT
5 hours
12 hours
20 hours
EX 11RT
7 hours
15 hours
24 hours
EX 5RT
Table 5-4: Efficiency On-line (RL Load) and Batteries Fully Charged.
kVA / kW
25%
50%
75%
100%
Output load percentage
5kVA /
4kWatts
90
91
91
91
Output: 220 / 230 / 240 Volts
89
90
91
91
Output: 200 / 208 / 250 Volts
7kVA /
4.9kWatts
90
89
91
90
91
91
91
90
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
11kVA /
8kWatts
90
89
91
90
90
90
90
89
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
Table 5-5: Efficiency On-Line (RCD Load) and Batteries Fully Charged.
kVA / kW
25%
50%
75%
100%
Output load percentage
5kVA /
4kWatts
90
91
91
92
Output: 220 / 230 / 240 Volts
89
91
91
91
Output: 200 / 208 / 250 Volts
7kVA /
4.9kWatts
90
89
91
91
91
91
92
91
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
11kVA /
8kWatts
90
89
92
91
91
90
91
90
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
Table 5-6: Efficiency on Battery (RCD Load).
kVA / kW
25%
50%
75%
100%
Output load percentage
5kVA /
4kWatts
87
89
89
88
Output: 220 / 230 / 240 Volts
87
88
89
88
Output: 200 / 208 / 250 Volts
7kVA /
4.9kWatts
87
87
89
88
89
89
88
88
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
11kVA /
8kWatts
89
88
90
90
89
89
87
88
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
86-86000-00 B01
Appendix
5—3
EX 5/7/11 RT Systems
Table 5-7: Efficiency on ECO Mode (All Kinds of Load) and Batteries Fully Charged.
kVA / kW
25%
50%
75%
100%
Output load percentage
5kVA /
4kWatts
96
97
96
97
Output: 220 / 230 / 240 Volts
95
96
96
96
Output: 200 / 208 / 250 Volts
7kVA /
4.9kWatts
96
95
97
96
96
96
97
96
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
11kVA /
8kWatts
96
95
97
96
96
96
97
96
Output: 220 / 230 / 240 Volts
Output: 200 / 208 / 250 Volts
5.6
Heat Rejection
Table 5-8: Full Load Heat Rejection in BTUs/hr.
Operation Mode
System
On-line
On Battery
5kVA
1350
1861
7kVA
1654
2280
11kVA
3033
3723
5.7
5—4
Environmental Characteristics
◗
The operating temperature is 0 to 40°C (8 hours at 45°C), however optimum operation is within the +20 to
+25°C range and at 5-95% humidity, non-condensing at altitude up to 3280ft without de-rating.
◗
The storage temperature: -20 to 40°C. Humidity: 5-95%, non condensing.
◗
Battery back-up time is adversely affected by high and low temperatures. It is significantly reduced at temperatures under 10°C. Above 25°C, battery service life is cut in half every 10°C. Above 40°C, battery manufacturers
no longer guarantee operation due to the risk of thermal runaway.
◗
Air enters through the front air vent grills and exits through the back. Always keep air vent grills unobstructed.
Appendix
86-86000-00 B01
Installation and User Manual
MGE Office Protection Systems
Customer Care Center
Technical Support and Product Services
?
Technical questions? If you encounter a problem while following the instructions in this manual, or have questions
about the operation, repair, or servicing of your equipment, please visit our web site www.mgeops.com for complete
service information.
To insure that your questions are correctly answered, please obtain the part number, assembly number, and serial number of
the unit and include them in any discussions or correspondence.
Part Number: ________________________________________________________________________________________
Assembly Number: __________________________________________________________________________________
Serial number: ______________________________________________________________________________________
Who To Contact
For Technical Support, Customer Care Center, Customer FAQ please visit our website: www.mgeops.com
Scheduling Field Service Engineer Support
Scheduling of the MGE Office Protection Systems Field Service Engineers typically should be done 7 to 10 days before they
are required on-site. If the startup of the UPS is critical to maintaining your schedule, please contact MGE Office Protection
Systems, to insure a safe installation and start-up that will maintain the MGE Office Protection Systems warranty and insure
smooth performance.
Return Policy for Single Phase Products (RMA)
Should you require factory service for your equipment, contact MGE Office Protection Systems Customer Care Center and
obtain a Return Materials Authorization (RMA) prior to shipping your unit. Never ship equipment to MGE Office Protection
Systems without first obtaining an RMA number.
For further details please visit our website: www.mgeops.com
Date: ______________________________________________________________________________________________
RMA Number: ______________________________________________________________________________________
Contact Name: ______________________________________________________________________________________
86-86000-00 B01
Glossary
Term used
Definition/Meaning
@
At.
/
And/or.
+/-
Plus or Minus.
≤
Equal to or less than.
#
Number.
°C
Degree Celsius.
°F
Degree Fahrenheit.
Ø
Phase angle.
Ω
Ohm; unit of resistance.
®
Trade Mark.
2nd
Second.
AC or ac
Alternating current, also implies root-mean-square (rms).
Ambient Temp.
Temperature of surrounding air.
Ambient noise
Acoustical noise of surrounding environment.
ANSI
American National Standard Institute.
AWG
American Wire Gauge.
Breaker
Electrical circuit interrupter.
BTU or Btu
British thermal unit. Defined as the amount of heat required to raise the temperature of one pound of water by 1°F.
Carrier
The company or individual responsible for delivering goods from one location to another.
C
Common.
CB
Circuit breaker.
cm
Centimeter.
Conduit
A flexible or rigid tube enclosing electrical conductors.
C.S.S.
Customer Support Service.
Current rating
The maximum current that a conductor or equipment can carry reliably without damage.
dBA
Decibel Adjusted.
86-86000-00 B01
Glossary
G—1
EX 5/7/11 RT Systems
G—2
dBrnC
Decibel above reference noise.
DC or dc
Direct current, or voltage.
Earth ground
A ground circuit that has contact with the earth.
Electrician
Refers to an installation electrician qualified to install heavy-duty electrical components in
accordance with local codes and regulations. Not necessarily qualified to maintain or repair
electrical or electronic equipment.
FET
Field effect transistor.
Freq.
Frequency.
Frequency slew rate
The change in frequency per unit of time. Given in term of Hz per second (Hz/sec.).
GND
Ground (safety).
Hz
Hertz, frequency measurement unit, 1Hz is one cycle per second.
I
Current.
IEC
International Electrotechnical Commission.
IEEE
Institute of Electrical and Electronic Engineers.
IGBT
Insulated gate bipolar transistors.
Input branch circuit
The input circuit from the building power panel to the equipment.
Inverter
An electrical circuit that generates an AC voltage source from a DC voltage source.
Inverter mode
See “on-line” mode.
I/O
Input/Output.
I/T or IT
Information Technology.
kVA
KiloVolt-Ampere; is equal to 1000 Volt-Ampere.
L
Line.
LCD
Liquid-Crystal Display unit.
LED
Light Emitting Diode.
Mains or Mains 1
Main AC input source.
Mains 2
Bypass AC input source.
mA
Milliampere.
MAX.
Maximum.
MCM
Thousand circular mil; standard wire sizes for multiple stranded conductors over 4/0 AWG
in diameter. M is from Roman numerical system indicating 1000.
N
Neutral.
NC
Normally closed.
NEC
National Electrical Code.
NFPA
National Fire Protection Association.
NO
Normally open.
Glossary
86-86000-00 B01
Installation and User Manual
OSHA
Occupational Safety and Health Agency.
PCA
Printed circuit assembly.
PCB
Printed circuit board.
PN
Part number.
PWM
Pulse Width Modulation.
RCD Load
Load consists of resistor, capacitor and diode. A computer with switched
mode power supply is considered a RCD load.
RL Load
Load consists of resistor, and inductor. A fan or a drill is considered a RL load.
SCR
Silicon controlled rectifier.
Shipping damage
Any damage done to an article while it is in transit.
SPDT
Single Pole Double Throw.
Static Transfer
An solid state switching mechanism electronically controlled to pass AC power
directly from the utility to an output load.
Technician
Refers to an electronic technician qualified to maintain and repair electronic
equipment. Not necessarily qualified to install electrical wiring.
V
Volts.
VA
Volt amperes.
VA
Volt-amps, unit for apparent power measurement, equal V x I.
VAC or Vac
Voltage of AC type.
VDC or Vdc
Voltage of DC type.
ve
Battery voltage.
Via
By way of.
86-86000-00 B01
Glossary
G—3
EX 5/7/11 RT Systems
(This page left blank intentionally)
G—4
86-86000-00 B01
Reorder Form
113 Whatney, Suite #101
Irvine, CA 92618
Use this form
NAME
to report any errors, omissions, or other problems you have experienced, or to
order additional hardcopies of this document. A free copy of this document may
be downloaded from the proprietary MGE Office Protection Systems Rep Web
site. Please contact your MGE Office Protection Systems Representative for
assistance.
_____________________________________________________________________________________
COMPANY ___________________________________________________________________________________
STREET ADDRESS ____________________________________________________________________________
CITY ________________________________________ STATE __________________ ZIP ___________________
I would like to order______ (quantity @ $50.00 each) additional copies of the:
Product Name
Installation and User Manual
86-86000-00 B01
I would like to report the following problems with this document:
w w w. m g e o p s . c o m
Contact MGE Office
Protection Systems
United States
MGE Office Protection Systems
13 Whatney, Suite #101
Irvine, CA 92618
(949) 268-2800
www.mgeops.com
1 3 W h a t n e y, S u i t e # 1 0 1 , I r v i n e , C a l i f o r n i a 9 2 6 1 8 • w w w. m g e o p s . c o m
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising