Samsung | LT-P326W | Installation guide | Samsung LT-P326W User manual

Samsung LT-P326W User manual
BN68-00653A-01Eng-00COVER
5/7/04 9:57 AM
Page 1
LT-P326W
1-800-SAMSUNG(1-800-726-7864)
U.S.A
Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
www.samsungusa.com
Canada
Samsung Electronics Canada Inc.
Samsung Customer Care
7037 Financial Drive
Mississauga, Ontario
L5N 6R3
www.samsung.ca
This device is a Class B digital apparatus.
BN68-00653A-01
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 1
CONTENTS
Chapter 1: Your New TV
List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Familiarizing Yourself with Your New TV . . . . . . . . . . . . . . . . . . . .
Right-side Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Batteries in the Remote Control . . . . . . . . . . . . . . . . . . . .
If remote control doesn’t work . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
2
3
4
6
6
Chapter 2: Installation
Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . .
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . . . .
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . . . .
Separate VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . .
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to a Cable Box that Descrambles All Channels . . . .
Connecting to a Cable Box that Descrambles Some Channels . .
Connecting HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to connect Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting an S-VHS VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a DVI-D Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a Digital TV Set-Top Box . . . . . . . . . . . . . . . . . . . . . .
Connecting a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANYNET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What is the Anynet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anynet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting TV + DVD/VCR Combo:
Connecting AV Signal Cables . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting TV + DVD Receiver: Connecting AV Signal Cables .
Connecting TV + DVD Combo + DVD Receiver:
Connecting AV Signal Cables . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
8
8
8
9
9
11
11
12
13
13
14
14
14
16
16
17
18
19
20
Chapter 3: Operation
Turning the TV On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Channel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Pre-CH Button to select the Previous Channel . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
21
21
21
21
22
22
23
26
Chapter 4: Special Features
Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memorizing the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . . .
Storing Channels in Memory (Automatic Method) . . . . . . . . .
Adding and Erasing Channels (Manual Method) . . . . . . . . . . .
Labeling Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To set-up your Favorite Channels . . . . . . . . . . . . . . . . . . . . . . . . . .
To Select Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Edit the Input Source Name . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
1
27
28
28
29
30
30
31
31
32
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 2
CONTENTS
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Automatic Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Blue Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fine Tuning Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LNA (Low Noise Amplifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Picture-in-Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating Picture-in-Picture . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Signal Source (External A/V) for PIP . . . . . . . . . .
Swapping the Contents of the PIP and Main image . . . . . . . . .
Changing the PIP Channel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Location of the PIP Window . . . . . . . . . . . . . . .
Changing the Size of the PIP Window . . . . . . . . . . . . . . . . . . .
DNIe(Digital Natural Image engine) . . . . . . . . . . . . . . . . . . . . . . . .
MCC (My Color Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Easy Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detail Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C (Intelligent Image Control) . . . . . . . . . . . . . . . . . . . . . . . . . . .
IBC (Intelligent Brightness Control) . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Screen Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freezing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Color Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the TruSurround XT(SRS TSXT) . . . . . . . . . . . . . . . . . . . .
Automatic Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Sound Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Headphone Sound . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Main or Sub Sound . . . . . . . . . . . . . . . . . . . . . . . . . .
Sub Woofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Weakness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Melody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
34
35
36
37
38
39
40
41
41
42
42
42
42
42
43
44
44
45
46
47
48
48
49
50
51
52
53
54
55
56
57
59
60
62
68
69
Chapter 5: PC Display
Using Your TV as a Computer (PC) Display . . . . . . . . . . . . . . . . . .
How to Set up Your PC Software (Windows only) . . . . . . . . .
How to Auto Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Screen Quality . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Screen Position . . . . . . . . . . . . . . . . . . . . . . . . .
To Initialize the Screen Position or Color Settings . . . . . . . . . .
70
70
71
72
73
74
Chapter 6: Troubleshooting
Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Appendix
Installing the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Wall Mount Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Cleaning and Maintaining Your TV . . . . . . . . . . . . . . . . . . . . . . . . . 85
Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . 85
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Contents
2
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 1
Chapter One
Y O U R N E W TV
List of Features
MCC (My Color Control):
Users can adjust colors to their preference by adjusting skin,sky and grass
tones.
I2C (Intelligent Image Control):
Automatically detects the input visual signal and adjusts to creat optimum
contrast.
IBC (Intelligent Brightness Control):
Adjusts the screen brightness automatically depending on the brightness of
the surrounding environment.
Color Weakness :
This feature enable those with a color weakness to view images as those
with normalvision.
JBL high performance built-in speakers:
Enables reproduction of broadband frequency sound.
List of Parts
Please make sure the following items are included with your LCD TV.
If any items are missing, contact your dealer.
Remote Control(BN59-00435A)
& Batteries (AAA x 2)
RF Cable
(AA39-00039A)
Power Cord
(3903-000085)
Owner’s
Instructions
Stand
(BN96-00380A)
Core(3301-001201)
x 2 (See Page 11)
English-1
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 2
Y O U R N E W TV
Familiarizing Yourself with Your New TV
Right-Side Panel Buttons
The buttons on the Right-side panel control your TV’s basic features, including the onscreen menu. To use the more advanced features, you must use the remote control.
POWER
SOURCE
Press to turn the TV on and off.
Displays a menu of all of the available
input sources (TV, AV, S-VIDEO, Component 1,
Component 2, HDMI, DVI, PC).
CH
Press to change channels.
Also press to highlight various items
on the on-screen menu.
POWER INDICATOR
Lights when unit is in standby mode.
Lights green after setting on/off timer.
+ VOL –
Press to increase or decrease the volume.
Also used to select items on the
on-screen menu.
REMOTE CONTROL SENSOR
Aim the remote control towards this spot
on the TV.
LIGHT DETECTING SENSOR
MENU
Press to see an on-screen menu of
your TV’s features.
Adjusts brightness of screen automatically
by detecting brightness of surrounding
environment. This sensor works when IBC is on.
SPEAKER
English-2
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 3
Y O U R N E W TV
Rear Panel Jacks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a DVD player.
For more information on connecting equipment, see pages 7-14.
HDMI IN
COMPONENT IN 1
Supports connections between HDMIconnection-enabled AV devices (set top
boxes, DVD players, AV receivers and digital
TVs).
Connect component video/audio from a
DVD/VCR/Set-top Box.
DVI-D INPUT
Connect to the digital video output jack on
your DVD/Set-top Box.
(DVI-D terminal does not support PC.)
S-VIDEO
Connect a Video signal from a
camcorder or VCR
AV INPUT/OUTPUT
Connect a Video signal from
a camcorder or VCR.
DVI-D AUDIO INPUT
ANT IN
Connect to the audio output jack on your
DVD/Set-top Box.
Connect to an antenna or to a cable TV system.
PC VIDEO (D-SUB) INPUT
Connect to an active (powered) subwoofer.
Connect to the video output port on your PC.
PC AUDIO (D-SUB) INPUT
SUBWOOFER OUTPUT
ANYNET
Connect to the audio output jack on your PC.
HEADPHONE JACK
COMPONENT IN 2
Connect a set of external headphones
for private listening.
Connect component video/audio from a
DVD/VCR/Set-top Box.
English-3
POWER INPUT
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 4
Y O U R N E W TV
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
When using the remote, always point it directly at the TV.
POWER
MODE
Turns the TV on and off.
(See Page 21)
Selects a target device to be controlled
by the Samsung remote control
(TV, VCR, Cable, DVD, Samsung STB)
(See pages 23~26)
P.SIZE
Press to change the screen size.
(See Page 48)
CH
and CH
(Channel UP/Down)
P.MODE
Press CH
or CH
to
change channels. (See Page 21)
Adjusts the TV picture by selecting
one of the preset factory settings.
(See Page 33)
VOL + and VOL Press to increase or decrease
the volume. (See Page 21)
MUTE
SOURCE
Press to temporarily cut off
the sound. (See Page 21)
Press to display all of the available
video sources. (See Page 31)
MENU
UP / DOWN / LEFT /
RIGHT / ENTER
Displays the main on-screen
menu.(See Page 22)
Use to select on-screen menu
items and change menu values.
(The remote control will only
function with VCR or DVD units
that are compatible with the LCD TV.)
PIP FUNCTIONS
Picture-in-Picture ON/OFF
(See pages 41~42)
English-4
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 5
Y O U R N E W TV
+100
PRE-CH
Press to select channels over 100.
For example, to select channel 121,
press “+100”, then press “2” and “1”.
(See Page 29)
Tunes to the previous channel.
(See page 21)
INFO
Anynet
Use to see information on the
current broadcast. (See Page 22)
Press the Anynet button to bring
up the Anynet menu. (See Page 16)
EXIT
Press to exit the menu.
STILL
Press to stop the action during
a particular scene. Press again to
resume normal video.
(See Page 48)
SIZE
Press to make the PIP window
double, large or small.
(See Page 42)
CH
Displays the available channels
in sequence.
(These buttons change channels
in the PIP window only.)
(See Page 42)
MTS
(Multi channel Television Stereo)
Press to choose stereo, mono or
Separate Audio Program
(SAP broadcast). (See Page 52)
SRS
RESET
(See Page 50)
When your remote does not work,
change the batteries and press the
RESET button for 2-3 seconds
before use.
AUTO PROG.
Press to automatically store
selected TV/cable channels.
(See Page 29)
SET BUTTON
ADD/DEL
Use to store and delete channels
to/from memory. (See Page 30)
SET button on TV remote control
adjusts 5 separate devices - TV,
VCR, Cable, DVD, or Samsung
Set-top box.
(See pages 23~26)
DNIe
Press to improve the digital video
quality. (See Page 43)
PC MODE
Press to switch to the PC mode.
(See pages 70~74)
FAV.CH
Tunes to the channels in your
favorite channel list. (See Page 31)
VCR/DVD Functions
-
Rewind
Stop
Play/Pause
Fast/Forward
English-5
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 6
Y O U R N E W TV
Installing Batteries in the Remote Control
1
Slide the cover out
completely.
Make sure to match the “+” and
“–” ends of the batteries with the
diagram inside the compartment.
2
Install two AAA size
batteries.
Remove the batteries and store them
in a cool, dry place if you won’t be
using the remote control for a long
time.
3
Replace the cover.
The remote control can be used
up to about 23 feet from the TV.
(Assuming typical TV usage,
the batteries last for about one year.)
If remote control doesn’t work
Check the following:
1. Is the TV power switch on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
English-6
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 7
C h a p t e r Tw o
I N S TA L L AT I O N
Connecting VHF and UHF Antennas
If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads” below.
If your antenna has one lead that looks
like this, see “Antennas with 75-ohm
Round Leads” on page 8.
If you have two antennas, see “Separate
VHF and UHF Antennas” on page 8.
Antennas with 300-ohm Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.
1
Place the wires from
the twin leads under
the screws on a 30075 ohm adaptor (not
supplied). Use a
screwdriver to tighten
the screws.
2
Plug the adaptor into
the ANT IN
terminal on the
bottom of the back
panel.
English-7
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 8
I N S TA L L AT I O N
Antennas with 75-ohm Round Leads
1
Plug the antenna
lead into the
ANT IN terminal
on the bottom of the
back panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires a an optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner.
2
Plug the combiner
into the ANT IN
terminal on the
bottom of the
rear panel.
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
Because this TV is cable-ready,
you do not need a cable box to
view unscrambled cable channels.
1
Plug the incoming
cable into the
ANT IN terminal
on back of the TV.
English-8
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 9
I N S TA L L AT I O N
Connecting to a Cable Box that Descrambles All Channels
This terminal might be labeled
“ANT OUT”, “VHF OUT”, or
simply, “OUT”.
1
Find the cable that is
connected to the
ANT OUT terminal
on your cable box.
2
Connect the other end
of this cable to the
ANT IN terminal on
the back of the TV.
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths
of coaxial cable. (These items are available at most electronics stores.)
This terminal might be labeled
“ANT IN”, “VHF IN”, or simply, “IN”.
1
Find and disconnect
the cable that is
connected to the
ANTENNA IN terminal
on your cable box.
2
Connect this cable
to a two-way splitter.
3
Connect a coaxial
cable between an
OUTPUT terminal on
the splitter and the IN
terminal on the cable
box.
English-9
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 10
I N S TA L L AT I O N
4
Connect a coaxial
cable between the
ANT OUT terminal
on the cable box
and the B–IN
terminal on the
A/B switch.
5
Connect another
cable between the
other OUT terminal
on the splitter and
the A–IN terminal on
the RF (A/B) switch.
6
Connect the last
coaxial cable
between the OUT
terminal on the RF
(A/B) switch and the
VHF/UHF terminal
on the rear of the TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal
viewing. Set the A/B switch to the “B” position to view scrambled channels.
(When you set the A/B switch to “B,” you will need to tune your TV to the cable box’s
output channel, which is usually channel 3 or 4.)
English-10
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 11
I N S TA L L AT I O N
Connecting HDMI
Supports connections between HDMI-connection-enabled AV devices (Set Top boxes, DVD
players, AV receivers and digital TVs).
1
Connect HDMI cable
from the TV to the input
terminal of the HDMI
device.
What is HDMI?
- HDMI, or high-definition multimedia interface, is a next-generation interface that enables the
transmission of digital audio and video signals using a single cable without compression.
- HDMI allows multiple
channels of digital audio (5.1 channels).The difference between HDMI and DVI is that the
HDMI device is smaller in size, has the HDCP(High Definition Content Protection)
coding feature installed, and supports multi - channel digital audio.
How to connect Core
Core provided reduces EMI(E1ectromagnetic Interference) noises from electrical
or electronic products and prevents magnetic impact from ambient environment.
After connecting AV cable of TV or Component cable, install Core as shown in the picture.
English-11
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 12
I N S TA L L AT I O N
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a
cable TV system (according to the instructions on pages 7-10).
Skip step 1 if you have not yet connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the
back of the TV.
2
Connect the cable or
antenna to the
ANT IN terminal
on the back of the
VCR.
3
Connect a coaxial
cable between the
ANT OUT terminal
on the VCR and
the antenna terminal
on the TV.
AV OUT
A coaxial cable is usually included with a VCR. (If not, check your local electronics store).
4
Connect a set of
audio cables
between the AUDIO
OUT jacks on the
VCR and the AUDIO
jacks on the TV.
AV OUT
If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook
up to the left and right audio input jacks of the TV. If your VCR is stereo, you must
connect two cables.
5
Connect a video
cable between the
VIDEO OUT jack on
the VCR and the
VIDEO jack on the
TV.
AV OUT
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
* Each external input source device has a different back panel configuration.
English-12
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 13
I N S TA L L AT I O N
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
1
To begin, follow
steps 1–3 in the
previous section to
connect the antenna
or cable to your
VCR and your TV.
AV OUT
2
Connect a set of audio
cables between the
AUDIO OUT jacks on
the VCR and the
AUDIO INPUT jacks
on the TV.
AV OUT
3
Connect an S-video
cable between the
S-VIDEO OUT jack on
the VCR and the
S-VIDEO INPUT jack
on the TV.
AV OUT
An S-video cable is usually included with an S-VHS VCR.
(If not, check your local electronics store.)
* Each external input source device has a different back panel configuration.
Connecting a DVI-D Cable
1
Connect a DVI-D
cable between the
DVI-I INPUT
connector on the TV
and the DVI connector
on the DVD player/
Set-Top BOX.
2
Connect a set of audio
cables between the
L-AUDIO-R jack
on the TV and the
AUDIO OUTPUT jacks
on the DVD player/
Set-Top BOX.
Note:If you are using a DVI-D cable to connect
1.Be sure to connect the audio cable (sold separately)as shown above to get normal TV sound.
2.See Appendix “Display Modes ”for supported resolutions.
3.The screen may have shifted to the right or to the left after connecting the cable.
The screen must be adjusted on the source(Set-top box).
4.Each external input source device has a different back panel configuration.
English-13
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 14
I N S TA L L AT I O N
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the
COMPONENT1 or
COMPONENT2 L, R
AUDIO INPUT
jacks on the TV and
the AUDIO OUT jacks
on the DVD player.
2
Connect a video cable
between the
COMPONENT1 or
COMPONENT2
(Y, PB, PR) jacks on
the TV and the Y, PB,
PR jacks on the DVD
player.
Note: For an explanation of Component video, see your DVD player owner's manual.
* Each external input source device has a different back panel configuration.
Connecting a Digital TV Set-Top Box
The connections for a typical set-top box are shown below.
1
Connect a set of audio
cables between the
L, R COMPONENT1
or COMPONENT2
AUDIO INPUT jacks
on the TV and the
AUDIO OUT jacks on
the Set-Top Box.
2
Connect a video cable
between the
COMPONENT1 or
COMPONENT2
(Y, PB, PR) jacks on
the TV and the Y, PB,
PR jacks on the
Set-Top Box.
Note: For an explanation of Component video, see your Set-Top Box owner's manual.
* Each external input source device has a different back panel configuration.
English-14
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 15
I N S TA L L AT I O N
Connecting a PC
Note: This figure shows the Standard Connector-jack panel.
The actual configuration on your TV may be different.
- Connect the D- Sub cable to “PC (PC IN)” on the rear of your set.
- Connect the stereo audio cable to “AUDIO (PC IN)” on the rear of your set
and the other end to “Audio Out” of the sound card on your computer.
TV Rear panel
PC VIDEO CABLE ( D-SUB )
<Not supplied>
PC AUDIO CABLE
<Not supplied>
English-15
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 16
I N S TA L L AT I O N
Anynet
Please refer to ‘ Anynet AV Owner’s Instructions’ that is provided separately for the detailed
information on Anynet.
1.What is the Anynet?
Anynet is an AV network system that enbles you to easily control Samsung audio-video (AV)
devices from your through the Anynet menu via a Samsung TV.
[ Anynet Features and Benefits ]
• Anynet allows you to access most features of any device connected to your TV set
from a single remote control.
With Anynet, there is no need to use different remote controls for different devices.
Moreover, there is no need to press separate buttons to switch devices.
+
+
•
Just choose a function from the Anynet menu and the rest of the process required is
performed automatically via the network linking the devices. It frees you from the
inconvenience of pressing separate buttons on separate devices several times to perform
a task.
- Ex} To play a DVD: Regular (Three remote controls; nine button presses)
- Through Anynet (One remote control; three button presses)
•
The Anynet network allows the devices connected to exchange control commands with
one another and check the operating status. As a result, you can use your TV remote
control to control your DVD player when you Play DVDs and to control the STB
when you watch the STB (set-top box) programs.
•
You can switch easily and conveniently between listening to the program
you are currently watching through your TV speakers or through Home Theater
with 5.1 channel speakers.
[ Anynet is most convenient when ]
• You watch content from external input source device such as DVDs, STB programs
or the VCR.
• You need to change channels, adjust the volume or skip scenes while you are watching
content from an external input source device.
• You want to switch between the TV speakers and the 5.1 channel speakers while you are
watching a program
English-16
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 17
I N S TA L L AT I O N
2.Anynet
1. Anynet System is available only for Samsung Anynet-supported AV devices.
2. See below for Anynet-supported devices.
(All devices except for 2 and 4 are soon to be added)
DVD Player
DVD/VCR Combo
DVD Recorder
DVD Receiver or Home Theater
DVD Recorder Combo
DVD Recorder Combo Receiver
AV Receiver
The Anynet does not support set-top
box models T165 and K165.
Satellite Set-Top Box
Cable Set-Top Box
HDTV Set-Top Box
3.
4.
5.
6.
7.
All video cables are connected to the TV set.
Anynet System does not support more than one of the same type of devices.
One Anynet System menu can support up to two devices besides the TV.
Anynet System can support only one Home theater.
“Standard Connection” means a connection configuration in which no digital
optical/coaxial cables are connected.
8. “Advanced Connection” means a connection configuration in which digital
optical/coaxial cables are connected.
9. Anynet begins to operate when the Anynet-supported AV devices are plugged in
and enter Standby mode.
English-17
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 18
I N S TA L L AT I O N
3. Connecting TV + DVD/VCR Combo:
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
1. Antenna Cable: Connect the external antenna cable to the ANT IN port on the TV.
2. Anynet Connector: To use the Anynet, connect the Anynet port on the TV and the
Anynet Input port on the DVD Combo using the Stereo-Stereo Anynet connector.
3. AV Connector: If you do not have a Component cable, connect the A/V output jacks on the
DVD/VCR Combo to the AV IN jacks on the TV.
4. Component Cable (Sold Separately): If you have the component connector cable,
connect Component Video Out jacks (DVD only) on the DVD/VCR Combo to the Component 1
Video Input jacks on the TV.
5. Audio Cable: After you complete step 4, connect the Component Audio Output jacks (DVD only)
on the DVD/VCR Combo and the Component Input 1 L-Audio-R jacks on the TV.
English-18
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 19
I N S TA L L AT I O N
4. Connecting TV + DVD Receiver:
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
1. Antenna Cable:Connect the external antenna cable to the ANT Input port of the TV.
2. Anynet Connectors:To use the Anynet,connect the Anynet port on the TV and the Anynet Input
port on the DVD Receiver using the Stereo-Stereo Anynet connector.
3. Video Connector:If you do not have the component connector, connect the Video Output port on
the DVD Receiver and the AV IN port on the TV.
4. Audio Connector:Connect the Left-Audio-Right port of Monitor Output on the TV and the Audio
Input port on the DVD Receiver.
5. Component Connector (Sold Separately):If you have the component connector,connect the
Color Difference Component Output port on the DVD Receiver and the Component Input 1
YpbPr port on the TV.
English-19
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 20
I N S TA L L AT I O N
5. Connecting TV + DVD Combo + DVD Receiver:
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
1. Antenna Cable: Connect the external antenna cable to the ANT IN port of the TV.
2. Anynet Connectors: To use Anynet, connect the Anynet port on the TV and the Anynet Input port
on the DVD/VCR Combo using the Stereo-Stereo Anynet connector.
3. Anynet Connectors: To use Anynet, connect the Anynet Output port on the DVD/VCR Combo and
the Anynet Input port on the DVD Receiver using the Stereo-Stereo Anynet connector.
4. AV Cable: If you do not have the component connector, connect the Output port of the AV output
jacks on the DVD/VCR Combo to the AV IN jacks on the TV.
5. Component Connector (Sold Separately): If you have the component connector, Connect the
Component Video Output jacks (DVD only) on the DVD/VCR Combo and the Component Input 1
“Y, PB , PR” jacks on the TV.
6. Audio Cable: Connect the L-Audio-R COMPONENT Audio In 1 jacks on the TV to the Analog
Audio Output jacks on the DVD/VCR Combo.
7. Component Cable (Sold Separately): Connect Component Video Out jacks on the DVD Receiver
to the COMPONENT Input 2 “Y, PB , PR” jacks on the TV.
8. Audio Cable:Connect the Left-Audio-Right port of Audio Output on the TV and the Audio Input
port on the DVD Receiver.
9. Optical Cable (Sold Separately): If you have an optical cable, connect the Digital Audio Output
Optical port on the DVD/VCR Combo to theDigital Input port on the DVD Receiver.
10.To enjoy 5.1-channel sound, go to “Set up” in the Anynet menu and select “Customized Setup”.
English-20
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 21
Chapter Three
O P E R AT I O N
Turning the TV On and Off
Press the POWER button.
You can also use the Power button on the front panel.
Changing Channels
Using the Channel Buttons
1
Press the CH
/
buttons to change channels.
When you press the CH /
buttons, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have
memorized at least three channels). You will not see channels that were either
erased or not memorized.
Using the PRE-CH Button to select the Previous Channel
1
Press the PRE-CH button.
The TV will switch to the last channel viewed.
To quickly switch between two channels that are far apart, tune to one channel,
then use the number button to select the second channel. Then use the PRE-CH
button to quickly alternate between them.
Adjusting the Volume
1
Press the VOL +/– buttons to increase or decrease the volume.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
1
Press MUTE and the sound cuts off.
” will appear in
The word “
the lower-left corner of the screen.
2
To turn mute off, press the MUTE button again, or simply
press the VOL +/- buttons.
English-21
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 22
O P E R AT I O N
Viewing the Display
The display identifies the current channel and the status
of certain audio-video settings.
The on-screen displays
disappear after about ten seconds.
Press the INFO button once more
or wait approximately 10 seconds
and it disappears automatically.
Allows the user to adjust the
settings according to his/her
preference and shows the
current settings.
1
Press the INFO button on the
remote control.
The TV will display the
channel, the type of sound,
and the status of certain
picture and sound settings.
Viewing the Menus
The on-screen menus
disappear from the screen after
about two minutes.
1
With the power on, press
the MENU button.
The main menu appears on
the screen. It’s left
side has five icons:
Input, Picture, Sound,
Channel, Setup.
2
Use the UP/DOWN
Then press ENTER
buttons to select one of the 5 icons.
to access the icon’s sub-menu.
3
Press the MENU button to exit.
English-22
You can also use
the MENU( ), CH Up/Down,
Volume Up/Down and
SOURCE(ENTER) buttons on the
TV to make selections.
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 23
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in five different modes:
TV, VCR, Cable, DVD or Samsung Set-top box. Pressing the corresponding button on the
remote control allows you to switch between these modes, and control whichever piece of
equipment you choose.
Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
This remote control is only compatible with Samsung Set-top boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the MODE button and make sure that the VCR LED
is illuminated.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter
three digits of the VCR code listed on page 26 of this
manual for your brand of VCR. Make sure you enter three
digits of the code, even if the first digit is a “0”.
(If more than one code is listed, try the first one.)
5 Press the Power button on the remote control. Your VCR
should turn on if your remote is set up correctly.
If your VCR does not turn on after set up, repeat steps
2, 3, and 4, but try one of the other codes listed for your
brand of VCR. If no other codes are listed, try each VCR
code, 000 through 088.
Note on Using Remote Control Modes: VCR
When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.
English-23
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 24
Setting Up the Remote to Operate Your Cable Box
1 Turn off your cable box.
2 Press the MODE button and make sure that the Cable LED is
illuminated.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three
digits of the cable box code listed on page 26 of this manual
for your brand of cable box. Make sure you enter three digits
of the code, even if the first digit is a “0.”
If there is more than one code listed, try the first one.
5 Press the Power button on the remote control. Your cable box
should turn on if your remote is set up correctly.
If your cable box does not turn on after set up, repeat steps
2, 3, and 4, but try one of the other codes listed for your brand
of cable box. If no other codes are listed, try each code, 000
through 077.
Note on Using Remote Control Modes: Cable Box
When your remote control is in “Cable Box” mode, the volume buttons still control your TV’s volume.
English-24
BN68-00653A-01Eng.qxd
5/7/04 9:03 AM
Page 25
Setting Up the Remote to Operate Your DVD
1Turn off your DVD.
2 Press the MODE button and make sure that the DVD LED is
illuminated.
3 Press the SET button on your TV’s remote control.
4Using the number buttons on your remote control, enter three
digits of the DVD code listed on page 26 of this manual for
your brand of DVD. Make sure you enter three digits of the
code, even if the first digit is a “0.”
If there is more than one code listed, try the first one.
5 Press the Power button on the remote control. Your DVD should
turn on if your remote is set up correctly.
If your DVD does not turn on after set up, repeat steps 2, 3, and
4, but try one of the other codes listed for your brand of DVD.
If no other codes are listed, try each code, 000 through 009.
Note on Using Remote Control Modes: DVD
When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.
English-25
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 26
Remote Control Codes
VCR Codes
Admiral
015,088
Aiwa
024
Audio Dynamics
022,025
Akai
026,031,032
Bell&Howell
011
Broksonic
019
016,018,022,054,055,061
Candle
017,062
Canon
Citizen
016,018,022,054,055,061
Colortyme
023
Craig
016,021
Curtis-Mathes 009,016,017,023,024,055,062,073,076
003,004,005,006,007,008,022,054,085
Daewoo
025,023
DB
009
Dimensia
024
Dynatech
036
Electrohome
017,018,019,022,024,029,032,036,043,
Emerson
050,051,056,058,066,071,074,076,077,079
011,021,027,028,052,057,067
Fisher
024
Funai
GE
016
Go Video
018,023,055,069
Goldstar
009,016,017,041,062
General Electric
023
Harman Kardon
014,024,044,045
Hitach
017
Instant Replay
JC Penny 011,014,016,017,023,025,039,044,060,062
JCL
011,017,023,025,039,055
JVC
kenwood
011,023,025,039,055
KLH
082
LG
001,002,007
Lloyd
024
040
Logik
024
LXI
017,038,062,065
Magnavox
011,017,023,025,038,039,055,070
Marantz
Marta
MEI
Memorex
MGA
Midland
Minota
Mitsubishi
Montgomery ward
016,024
MTC
016,024,040,041
Multitech
011,023,025,039,055,070,073
NEC
015
Optimus
017,062,084,086
Panasonic
014,044
Pentax
055
Pentex Reserch+
017,038,062,065
Philco
017,038
Philips
014,025,042,059
Pioneer
053,054,061
Portland
009
ProScan
011
Quartz
017,053
Quasar
011,015,017,018,021,
Radio Shack/Realistics
024,028,036,052,062
009,014,016,017,037,044,046,063,078
RCA
000,016,022,031,041,051
Samsung
025
Sansui
011,021
Sanyo
022,050,058,077
Scott
011,014,018,021,027,028,044,052,057
Sears
015,036,048,054
Sharp
026,035,040,064
Shintom
024
Signature
026,035,047
Sony
017,024,038,062,065
Sylvania
024
Symphonic
011,024
Tandy
Tashiko
039
Tatung
024,039,078
Teac
045,051
Macom
Magnavox 015,016,027,029,034,036,037,040,041,048,049
001
Nawoo
017
NSC
024,046
Oak
024
Osk Sigma
011,035,047,069
Panasonic
015,016,027,029,034,036,037,040,041,048,049
Philips
026,028,052
Pioneer
015,016
Randtek
008,035,074
RCA
011,020,021
Regal
010,041
Regency
SAEWOO
007
Signature
054
Sprucer
035
Starcom
054
Stargate 2000
066
Sylvania
019,067
TaePyungYang
002
Texscan
019,067
Tocom
025,029,057,058,063
Unika
039,040,049
Universal
059,060
Viewstar 015,016,027,029,034,036,037,040,041,048,049
Warner Amex
052
Zenith
022,050,065,069
Technics
Temika
Teknika
TMK
Toshiba
Toshiko
Totevision
Unitech
Vector Research
Victor
Video Concepts
Videosonic
Wards
Yamaha
Zenith
018,030
076
014,022,028,057,058
018
016,018
Cable Box Codes
Anvision
Cable star
DeaRyung
DongKuk
DaeHan
Eagle
Eastrm Int.
Eastern International
General Instrument
GI
Hamlin
Hitachi
Jerrold
LG
015,016
015,016
003
004
005
015,016
020
054
012,013,023,031,032,
033,038,044,075,076,077
011,012,020,021,042,056
045,051,054
012,013,023,031,032,033,038,044,054,070,073 SA
006 Samsung
000,011,030,052,071,072
DVD Codes
CurtisMathes
JVC
LG
Philips
Proscan
RCA
009
003
001
007
008
008
Toshiba
Panasonic
Sony
Samsung
Sharp
002
006
004
000
005
English-26
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 27
Chapter Four
S P E C I A L F E AT U R E S
Plug & Play Feature
When the TV is initially powered On, two basic customer settings proceed
automatically and subsequently: Setting Auto program, Clock.
1
Press the POWER
button on the remote control.
The message “Plug & Play”
is displayed.
2
Select the appropriate
Language by pressing the
UP/DOWN
buttons.
Press the ENTER
button
to confirm your choice.
The message “Antenna Input
Check,” is displayed with
“OK ” selected.
Press the ENTER
button.
3
Press the UP/DOWN
buttons to select “Air”, “STD”,
HRC”, or “IRC”, then press
the ENTER
button.
Press the ENTER
button to stop.
4
Press the LEFT/RIGHT
buttons to move to the “Hour”,
“Minute” or “am/pm”.
Set the hour or minute by
pressing the UP/DOWN
buttons.(Refer to “Setting the
Clock” on page 56.)
5
Press the MENU(
) button
to confirm your setting.
The message “Enjoy your watching.”
is displayed.
English-27
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 28
O P E R AT I O N
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH
and CH
buttons to scan through the channels. This eliminates the need to change channels by
entering the channel digits. There are three steps for memorizing channels: selecting a
broadcast source, memorizing the channels (automatic) and adding and deleting channels
(manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the
type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Channel”,
then press the ENTER
button.
2
Press the ENTER
button.
Repeatedly press the
UP/DOWN
buttons to
cycle through these choices:
“Air”, “STD”, “HRC” or “IRC”
(all cable TV).
Press the EXIT button to exit.
Note : STD, HRC and IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable system
that exists in your particular area.
At this point the signal source has been selected.
Proceed to “Storing Channels in Memory” (next page).
English-28
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 29
O P E R AT I O N
Storing Channels in Memory (Automatic Method)
1
First, select the correct
signal source
(Air, STD, HRC, IRC).
See steps 1~2 on previous
page.
2
Press the UP/DOWN
buttons to select
“Auto Program”.
Press the ENTER
button.
The TV automatically cycles
through all of the available
channels and stores them in
memory. This takes about
one to two minutes.
Press ENTER at any time
to interrupt the memorization
process and return to the
Channel menu.
3
Press the LEFT/RIGHT
buttons to select “Start”, then
press the ENTER
button.
The TV will begin memorizing
all of the available channels.
4
After all the available
channels are stored, the Auto
program menu reappears.
Press the EXIT button to exit.
To select channels over 100
Ex) Press
to select channel 108.
English-29
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 30
O P E R AT I O N
Adding and Erasing Channels (Manual Method)
1
Use the number buttons to directly
select the channel to Add or Delete.
Press the MENU button to
display the menu.
buttons
Press the UP/DOWN
to select “Channel”, then press
the ENTER
button.
Press the UP/DOWN
to select “Add/Delete”.
Press the ENTER
buttons
button.
Press the ENTER
to select
“Add” or “Delete” (pressing
ENTER
toggles between the
two).
Press the EXIT button to exit.
Alternate method:
Use the number buttons to directly select the channel that will be added or
erased. Press the “ADD/DEL” button.
Repeatedly pressing ENTER
will alternate between “Add”and“Delete”.
Press the EXIT button to exit.
You can view any channel (including an erased channel) by using the number
buttons on the remote control.
Labeling Channels
1
Press the MENU button to display
the menu.
buttons
Press the UP/DOWN
to select “Channel”, then press
the ENTER
button.
buttons
Press the UP/DOWN
to select “Name”, then press the
ENTER
button.
2
Press the UP/DOWN
to select a channel.
buttons
You can assign a name to a channel.
buttons
Press the LEFT/RIGHT
to move to “Labeling” and use
the UP/DOWN
buttons to assign
a name.
Repeat this procedure to enter up to
four characters.
Press the EXIT button to exit.
English-30
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 31
O P E R AT I O N
To Set-up Your Channels
1
Press the MENU button
to display the menu.
Press the UP/DOWN
buttons to select “Channel”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select “Favorite
Channel”, then press the
ENTER
button.
2
Press the UP/DOWN
buttons to select your
favorite channels to watch
among the labeled channels.
button
Press the ENTER
to add a check mark to
set the channel as a favorite
channel.
Press the EXIT button when
done to exit.
3
To select the Favorite channels, you have set-up, press the FAV.CH
button on the remote.
To Select Source
Use to select TV or other external input source connected to the TV.
Use to select the input source of your choice.
If Connector is not connected,
Source cannot be selected except
TV. (in both main and sub-screen)
1
Press the MENU button to
display the on-screen menu.
Press the ENTER
button.
2
Press the ENTER
button.
Press the UP/DOWN
buttons to select the Input
source, then press the
ENTER
button.
English-31
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 32
O P E R AT I O N
To Edit the Input Source Name
Name the input device connected to the input jacks to make your input source selection easier.
1
Press the MENU button to
display the on-screen menu.
Press the ENTER
to select “Input”.
button
Press the UP/DOWN
buttons to select
“Edit Name”, then press
the ENTER
button.
2
Press the UP/DOWN
buttons to select
“AV”, “S-Video”,
“Component1”,
“Component2”, “HDMI”,
“DVI”, or “PC” input jack,
then press the ENTER
button.
3
Press the UP/DOWN
buttons to select “VCR”,
“DVD”,“Cable STB”,
“HD STB”,“Satellite STB”,
“AV Receiver”,“DVD
Receiver”, “Game",
“Camcorder”, “DVD Combo”,
“DHR(DVD HDD Recoder)”,
or “PC” input source, then
button.
press the ENTER
Press the EXIT button to
exit.
English-32
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 33
O P E R AT I O N
Using Automatic Picture Settings
Your TV has four automatic picture settings (“Dynamic”, “Standard”, “Movie”, and
“Custom”) that are preset at the factory. You can activate either Dynamic, Standard,
Movie, or Custom by pressing P.MODE (or by making a selection from the menu).
Or, you can select “Custom” which automatically recalls your personalized picture settings.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
2
Press the ENTER
button.
Press the UP/DOWN
buttons to select the
“Dynamic”, “Standard”,
“Movie”, or “Custom”
picture setting.
Press ENTER
button.
Press the EXIT button to exit.
Alternate method:
Simply press the P.MODE button on the remote control to select
one of the standard picture settings.
•
•
•
•
Choose Dynamic to increase the clarity and sharpness of the picture.
Choose Standard for the standard factory settings.
Choose Movie when viewing the Movie.
Choose Custom if you want to adjust the settings according to personal
preference (see “Customizing the Picture, page 34).
English-33
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 34
O P E R AT I O N
Customizing the Picture
You can use the on-screen menus to change the contrast, brightness, sharpness,
color and tint according to personal preference.
(Alternatively, you can use one of the “automatic” settings. See the previous page.)
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “Custom”,
then press the ENTER
button.
3
Press the ENTER
button to select “Contrast”,
“Brightness”, “Sharpness”,
“Color”, or “Tint”.
4
Press the LEFT/RIGHT
buttons to decrease or
increase the value of a
particular item.
For example, if you select
“Contrast”, pressing RIGHT
increases it.
Press the EXIT button to exit.
English-34
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 35
O P E R AT I O N
Using Automatic Sound Settings
Your TV has five automatic sound settings (“Standard”, “Music”, “Movie” “Speech” and
“Custom”) that are preset at the factory. You can select “Custom Sound”, which automatically
recalls your personalized sound settings.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
Press the ENTER
button.
2
Press the UP/DOWN
buttons repeatedly to select
the “Standard”, “Music”,
“Movie”, “Speech”, or
“Custom” sound settings.
Press the EXIT button
to exit.
•
•
•
•
•
Choose Standard for the standard factory settings.
Choose Music when watching music videos or concerts.
Choose Movie when watching movies.
Choose Speech when watching a show that is mostly dialog (i.e., news).
Choose Custom to recall your personalized settings.
English-35
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 36
O P E R AT I O N
Customizing the Sound
The sound settings can be adjusted to suit your personal preference.
(Alternatively, you can use one of the “automatic” settings. See the previous page.)
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Custom”, then press the
ENTER
button.
3
Press the
LEFT/RIGHT
buttons
to select a particular item
to be changed.
Press the
UP/DOWN
buttons to increase or
decrease the value of a
particular item.
Press the EXIT button
to exit.
Note :The equalizer allows you to adjust frequencies to your preference.
Note :The lowest frequency is 100 and 10K is the highest.
English-36
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 37
O P E R AT I O N
Selecting a Menu Language
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “Language”.
Press the ENTER
button.
3
Press the UP/DOWN
buttons to select “English”,
“Français”, “Español”, or
“Português”.
Press the EXIT button
to exit.
English-37
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 38
O P E R AT I O N
Setting the Blue Screen Mode
If no signal is being received or the signal is very weak, a blue screen automatically
replaces the noisy picture background.
If you wish to continue viewing the poor picture, you must set the “Blue screen”
mode to “Off”.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “Blue
Screen”, then press the
ENTER
button.
Pressing the UP/DOWN
buttons will alternate between
“On” and “Off”.
3
Press the UP/DOWN
buttons to set Blue Screen
“On” or “Off”.
Press the EXIT button
to exit.
English-38
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 39
O P E R AT I O N
Fine Tuning Channels
Use fine tuning to manually adjust a particular channel for optimal reception.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Channel”,
then press the ENTER
button twice.
2
Press the UP/DOWN
buttons to selec “Fine Tune”,
then press the ENTER
button.
If you do not store the fine-tuned
channel in memory, adjustments
are not saved.
3
Press the LEFT/RIGHT
buttons to adjust the fine
tuning.
Fine tuned channels that have
been saved are marked with an
asterisk “*”on the right-hand side
of the channel number in the
channel banner.
4
To store the fine tuning
setting in the TV’s
memory, press the
ENTER
button.
Press the EXIT button
to exit.
English-39
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 40
O P E R AT I O N
LNA (Low Noise Amplifier)
If the TV is operating in a weak-signal area, sometimes the LNA function can
improve the reception (a low-noise preamplifier boosts the incoming signal).
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Channel”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “LNA”,
then press the ENTER
button.
Pressing the UP/DOWN
buttons will alternate between
“On” and “Off”.
3
Press the UP/DOWN
buttons to set LNA “On” or
“Off”.
Press the EXIT button
to exit.
English-40
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 41
O P E R AT I O N
Viewing Picture-in-Picture
This product has one built-in tuner, which does not allow PIP to function in the
same mode. For example, you cannot watch one TV channel in the main screen,
and a different one in the PIP screen. Please see ‘PIP Settings’below for details.
You can use the PIP feature to simultaneously watch two video sources.
Note: While V-Chip is in operation, the PIP function cannot be used.
Activating Picture-in-Picture
Quick way to access
the PIP menu:
Simply press the PIP
on the remote control.
1
Press the MENU button to
display the menu.
TV
Picture
:
Mode
Custom
Color Tone
Size
DNIe
PIP
MCC
: Normal
: Wide
: DNIe On
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
Custom
Press the UP/DOWN
buttons to select “PIP”
then press the ENTER
button.
Move
More
Enter
Return
If you turn the TV off while
watching and turn it on again,
the PIP window will disappear.
2
Press the ENTER
button.
Press the UP/DOWN
buttons to select “On”.
TV
PIP
PIP
Source
Swap
Size
Position
Ch.
: On
: TV
:
:
: Air
Move
2
Enter
Return
O : PIP operates
X : PIP doesn’t operate
PIP Settings
Sub Picture
TV
AV
S-Video
COMP 1
COMP 2
HDMI
DVI
PC
TV
O
O
O
O
O
O
O
O
Main Picture
button
AV
O
O
O
O
O
O
O
O
S-Video
O
O
O
O
O
O
O
O
COMP 1
O
O
O
X
X
X
X
X
COMP 2
O
O
O
X
X
X
X
X
HDMI
O
O
O
X
X
X
X
X
DVI
O
O
O
X
X
X
X
X
PC
O
O
O
X
X
X
X
X
English-41
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 42
O P E R AT I O N
Selecting a Signal Source (External A/V) for PIP
3
Press the UP/DOWN
buttons to select “Source”,
then press the ENTER
button.
TV
PIP
PIP
Source
Swap
Size
Position
Ch.
Select a source of the sub
picture by pressing the
UP/DOWN
buttons and
button.
press the ENTER
Move
: On
:
:
:
:
TV
AV
S-Video
Component 1
Component 2
Enter
Return
Note :If Connector is not connected, Source cannot be selected except TV.
(in both main and sub-screen)
Source selection is possible only when Component 1,
Component 2, HDMI, DVI, or PC is connected.
Swapping the Contents of the PIP and Main image
4
Press the UP/DOWN
buttons to select “Swap”,
then press the ENTER
button.
Changing the PIP Channel
5
Press the UP/DOWN
buttons to select “Ch.(Channel)”,
then press the ENTER
button.
Changing the Position of the PIP Window
You can select the channel
that you want to view through
sub picture by pressing the
UP/DOWN
buttons.
6
Press the UP/DOWN
buttons to select “Position”,
then press the ENTER
button.
Changing the Size of the PIP Window
7
Press the UP/DOWN
buttons to select “Size”,
then press the ENTER
button.
Press the EXIT button
to exit.
• When the PC is in energy saving mode, you cannot choose the PIP option.
• You may notice that the picture in the PIP window becomes slightly unnatural when you set the main
screen to game or karaoke mode.
• Switch the main screen and the PIP window for normal viewing.
English-42
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 43
O P E R AT I O N
DNIe (Digital Natural Image engine)
Samsung’s New Technology brings you more detailed images with contrast,
white enhancement and 3D noise reduction.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “DNIe”,
then press the ENTER
button.
3
Press the UP/DOWN
buttons to select “DNIe On”,
“DNIe Off ”, “DNIe Demo”,
then press the ENTER
button.
Press the EXIT button
to exit.
•
•
•
DNIe On: Improved picture mode as demonstrated by DNIe Demo is activated.
DNIe Off: The mode is deactivated and the screen returns to it’s original condition.
DNIe Demo: The screen shows the improved image on the left-hand side and
the original image on the right-hand side.
English-43
BN68-00653A-01Eng.qxd
5/7/04 9:04 AM
Page 44
O P E R AT I O N
MCC (My Color Control)
MCC allows users to adjust colors to their preference, by adjusting skin, sky and
grass tones using the predefined settings(Standard, Custom, Turkish Blue, Emerald
Green, and Indian Pink) without affecting other colors on the screen.
Easy Control
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select “MCC” then
press the ENTER
button.
This function doesn’t work when
Source is in PC mode,
or DNIe is in off mode.
2
Press the
UP/DOWN
buttons
to select “Easy Control”,
then press the ENTER
button.
3
Press the LEFT/RIGHT
buttons to select among the
various picture settings, then
press ENTER
.
The Original picture (before
adjustment) is shown on the
left side, while the selected
mode is shown on the right.
• The sources are displayed in the following order :
Turkish Blue - Emerald Green - Indian Pink - Standard - Custom
English-44
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 45
O P E R AT I O N
Detail Control
You can adjust skin, sky and
grass tones without using the
predefined settings in custom
mode.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select “MCC” then
press the ENTER
button.
This function doesn’t work
when the Source is in PC mode,
or DNIe is in off mode.
2
Press the UP/DOWN
buttons to select
“Detail Control”, then
press the ENTER
button.
3
Press the UP/DOWN
buttons to select the desired
MCC color and press the
ENTER
button.
Press the LEFT/RIGHT
buttons to increase or
decrease the value of a
particular item.
Press the EXIT button
to exit.
• The sources are displayed in the following order :
Skin Tone - Green Grass - Blue Sky- Reset
English-45
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 46
O P E R AT I O N
I2C (Intelligent Image Control)
I2C (Intelligent Image Control) automatically detects the inputted
visual signal and adjusts to create optimum contrast.
1
Press the MENU button
todisplay the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
This function doesn’t work
when the Source is in PC mode,
or DNIe is in off mode.
2
Press the
UP/DOWN
buttons
to select “I2C”, then press
the ENTER
button.
3
Press the
UP/DOWN
buttons to
select “On” or “Off”.
Press the EXIT button
to exit.
English-46
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 47
O P E R AT I O N
IBC (Intelligent Brightness Control)
The IBC (Intelligent Brightness Control) adjusts the screen brightness automatically
by using a light detecting sensor.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
This function doesn’t work
when the Source is in PC mode.
2
Press the UP/DOWN
buttons to select “IBC”,
then press the ENTER
button.
Screen brightness is
adjusted automatically depending
on the brightness of the
surrounding environment.
3
Press the LEFT/RIGHT
buttons to select “On” or
“Off”.
Press the EXIT button
to exit.
English-47
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 48
O P E R AT I O N
Changing the Screen Size
1
Press the P.SIZE button to change the screen size.
•
•
•
•
Note :Only wide and size of 4:3
can be selected for PC
Source.
Wide
: Sets the picture to 16:9 wide mode.
Panorama : Use this mode for the wide aspect ratio of a panoramic picture.
Zoom 1,2 : Magnifies the size of the picture on screen.
4:3
: Sets the picture to 4:3 normal mode.
This is the standard TV screen size.
Freezing the Picture
1
Press the STILL button to freeze a moving picture.
• Normal sound will still be heard.
Press again to cancel.
English-48
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 49
O P E R AT I O N
Adjusting the Color Tone
You can change the color of the entire screen according to your preference.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Picture”,
then press the ENTER
button.
2
Press the
UP/DOWN
buttons
to select “Color Tone”,
then press the ENTER
button.
Choose from the following
Color Tone settings:
“Cool 2”, “Cool 1”,
“Standard”, “Warm 1”,
“Warm 2” according to
personal preference.
3
Press the
UP/DOWN
buttons to
select “Cool 2”, “Cool 1”,
“Normal”, “Warm 1”,
or “Warm 2”.
Press the EXIT button
to exit.
English-49
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 50
O P E R AT I O N
Setting the TruSurround XT(SRS TSXT)
Emphasizes midrange and bass and provides a simulated surround-sound
experience.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “SRS
TSXT”, then press the
ENTER
button.
3
Press the UP/DOWN
buttons to select “Off”,
“3D Mono ”, “Stereo”,
then press the ENTER
button.
Press the EXIT button
to exit.
TRADEMARK & LABEL LICENSE NOTICE
is a trademark of SRS Labs,Inc. TruSurround XT technology is
incorporated under license from SRS labs, Inc.
English-50
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 51
O P E R AT I O N
Automatic Volume Control
Reduces the differences in volume level among broadcasters.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “Auto
Volume”, then press the
ENTER
button.
3
Press the UP/DOWN
buttons to set Auto Volume
“On” or “Off ”
Press the EXIT button
to exit.
English-51
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 52
O P E R AT I O N
Special Sound Options
Choosing a Multi-Channel Sound (MTS) Soundtrack
Depending on the particular program being broadcast, you can listen to stereo,
mono, or a Separate Audio Program. (SAP audio is usually a foreign-language
translation. Sometimes SAP has unrelated information like news or weather).
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “MTS”,
then press the ENTER
button.
3
Press the
UP/DOWN
buttons
to select “Mono”, “Stereo”
or “SAP”, then press
the ENTER
button.
Press the EXIT button to
exit.
•
•
•
Choose Stereo for channels that are broadcasting in stereo.
Choose Mono for channels that are broadcasting in mono, or if you are having
difficulty receiving a stereo signal.
Choose SAP to listen to the Separate Audio Program, which is usually a
foreign-language translation.
You can also change the MTS setting by pressing the “MTS” button on the remote
control. (When you change channels, MTS is set to “Stereo” automatically.
To listen in ‘SAP’ or ‘Mono,’ change the MTS setting).
English-52
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 53
O P E R AT I O N
Adjusting the Headphone Sound
The headphone option is especially useful when simultaneously watching the main
screen and the PIP window.
Note :Headphones must be
purchased separately.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Headphone”, then press
the ENTER
button.
3
Press the UP/DOWN
buttons to select the
particular item to be
changed.
4
Press the LEFT/RIGHT
buttons to decrease or
increase the value of
a particular item.
Press the EXIT button
to exit.
English-53
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 54
O P E R AT I O N
Selecting the Main or Sub Sound
You can select to hear sound from either the Main or Sub picture when PIP is On.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “Sound
Select”, then press the
ENTER
button.
3
Press the UP/DOWN
buttons to select
“Main” or “Sub”.
Select “Main” to hear the
main TV sound and select
“Sub” to hear the PIP
window sound.
Press the EXIT button
to exit.
English-54
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 55
O P E R AT I O N
Sub Woofer
The TV provides an output for hookup to an active(powered) subwoofer.
Note : Extra sub-woofer speaker is necessary to emphasize low-key sound.
Adjust cutoff frequency to emphasize the lower keys.
1
Press the MENU button to
display the on-screen menu.
Press the UP/DOWN
buttons to select “Sound”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Sub Woofer ”, then press
the ENTER
button.
3
Press the ENTER
button.
Press the UP/DOWN
buttons to select “On”,
then press the ENTER
button.
Press the
UP/DOWN
buttons
to select the particular
item to be changed.
Press the
LEFT/RIGHT
buttons
to decrease or increase
the value of a particular
item.
Press the EXIT button
to exit.
English-55
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 56
O P E R AT I O N
Setting the Clock
Setting the clock is necessary in order to use the various timer features of the TV.
Also, you can check the time while watching the TV. (Just press the INFO button).
1
Press the MENU button to
display the on-screen menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the ENTER
button
to select “Time”, then press
the ENTER
button to
select “Clock”.
Note :You can also set the
time using the numeric
buttons on the remote.
3
Press the UP/DOWN
buttons repeatedly until the
correct “Hour” appears.
After the hour is entered,
press the LEFT/RIGHT
buttons to select “Minute”.
Press the UP/DOWN
buttons until the correct
“Minute” appears.
Press the LEFT/RIGHT
buttons to select “am/pm”
and adjust with the
UP/DOWN
buttons.
Press the EXIT button to exit.
English-56
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 57
O P E R AT I O N
Setting the On/Off Timer
Before using the timer,
you must set the TV’s clock.
(See “Setting the Clock”
on page 56)
1
Press the MENU button to
display the on-screen
menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
Press the ENTER
button to select “Time”.
When you set the hours,
make sure the correct time
of day (am or pm) appears
to the right of the time.
2
Press the UP/DOWN
buttons to select
“On Timer”, then press the
ENTER
button.
Press the UP/DOWN
buttons repeatedly to
select the appropriate “Hour”.
Press the LEFT/RIGHT
buttons repeatedly to
select the appropriate
minute (i.e., the time when
the TV will turn on).
English-57
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 58
O P E R AT I O N
To deactivate the “On Timer,”
select “Off” during this step.
3
Press the LEFT/RIGHT
buttons to select “Setup”.
Press the
UP/DOWN
buttons
to On Timer “On”.
(Repeatedly pressing
the UP/DOWN
buttons will alternate
between On and Off).
When finished, press the
ENTER
button.
4
To set the Off time,
press the UP/DOWN
buttons to select
“Off Timer”.
Press the ENTER
button and set the hours
and minutes. (Follow the
same procedure as in
steps 2 and 3 above).
5
When finished setting the timer, press the EXIT button to exit.
•
Auto Power Off
When you set the timer on, your television will be turned
off if you do not operate any controls for 3 hours after
the TV has been turned on with the ‘Timer On’ function.
‘Auto power off’ operates only when the TV has been
turned on by the 'Timer on' function.
English-58
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 59
O P E R AT I O N
Setting the Sleep Timer
Set the timer for the TV to turn off at the preset time automatically.
Sleep timer
1
Press the MENU button
to display the on-screen
menu.
Press the
UP/DOWN
buttons
to select “Setup”, then
press the ENTER
button.
Press the ENTER
button to select “Time”.
2
Press the
UP/DOWN
buttons
to select “Sleep Timer”,
then press the
ENTER
button.
3
Press the
UP/DOWN
buttons
repeatedly until the
correct time appears.
Press the EXIT button
to exit.
English-59
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 60
O P E R AT I O N
Viewing Closed Captions
Your TV decodes and displays the closed captions that are broadcast with certain TV shows.
These captions are usually subtitles for the hearing impaired or foreign-language translations.
All VCRs record the closed caption signal from television programs, so home-recorded
video tapes also provide closed captions. Most pre-recorded commercial video tapes provide
closed captions as well. Check for the closed caption symbol in your television schedule and
on the tape’s packaging :
.
1
Press the MENU button to
display the on-screen menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select “Caption”,
then press the ENTER
button.
▼
Misspellings and unusual
3characters sometimes occur during
closed
Press
thecaption
ENTERtransmissions, especially
those of live events. There may be a
button.
small delay before captions appear
when you change channels. These are
not malfunctions of the TV.
In caption mode, captions
appear
4 at the bottom of the screen,
and
theythe
usually
cover only a small
Press
UP/DOWN
portion
buttonsoftothe
setpicture.
caption
“Off ” or “On”, then press the
InENTER
text mode,
information unrelated
button.
to the program, such as news or
weather, is displayed. Text often
covers a large portion of the screen.
5
Depending on the particular broadcast, it might be
necessary to alter the settings to “Channel” and “Field”.
English-60
Different channels and fields
display different information:
Field 2 carries additional
information that supplements
the information in Field 1.
(For example, Channel 1 may
have subtitles in English,
while Channel 2 has subtitles
in Spanish).
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 61
O P E R AT I O N
6
Press the UP/DOWN
buttons to select “Mode”,
then press the ENTER
button.
Press the UP/DOWN
buttons to set “Cation” or
“Text”, then press the
ENTER
button.
7
Press the UP/DOWN
buttons to select “Channel”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select “1” or “2”,
then press the ENTER
button.
8
Press the UP/DOWN
buttons to select “Field”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select “1” or “2”,
then press the ENTER
button.
Press the EXIT button to
exit.
English-61
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 62
O P E R AT I O N
Using the V-Chip
The V-Chip feature automatically locks out programming that is deemed inappropriate for
children. The user must first enter a Pin (personal ID number) before any of the V-Chip
restrictions can be set up or changed.
Setting Up Your Personal ID Number (PIN)
1
Press the MENU button
to display the menu.
Press the
UP/DOWN
buttons
to select “Setup”, then
press the ENTER
button.
2
Press the
UP/DOWN
buttons
to select “V-Chip”, then
press the ENTER
button.
3
The “Enter Pin” screen
will appear. Enter your
4-digit Pin number.
Note: The default Pin
number for a new TV
set is “0-0-0-0.”
4
After entering a valid
PIN number, the
“V-Chip” screen will
appear. Press the
UP/DOWN
buttons
to select “Change Pin”.
Note: If you forget the Pin,
press the remote-control
buttons(with the unit “Off”)
in the following
sequence,which resets the
pin to 0-0-0-0:
POWER OFF ➔ MUTE ➔
8 ➔ 2 ➔ 4 ➔ POWER ON.
5
Press the ENTER
button.
The Change Pin screen
will appear. Choose any
4-digits for your PIN and
enter them.
As soon as the 4 digits
are entered, the “Confirm
New Pin” screen appears.
Re-enter the same 4 digits.
When the Confirm screen
disappears, your Pin has
been memorized.
Press the EXIT button to
exit.
English-62
ol
Off”)
the
E➔
ON.
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 63
O P E R AT I O N
How to Enable/Disable the V-Chip
Note : PIP operation is disabled when the V-chip is on.
1
Press the MENU button
to display the menu.
Press the
UP/DOWN
buttons
to select “Setup”, then
press the ENTER
button.
2
Press the
UP/DOWN
buttons
to select “V-Chip”, then
press the ENTER
button.
3
The “Enter Pin” screen
will appear. Enter your
4-digit Pin number.
Note: The default Pin
number for a new TV
set is “0-0-0-0.”
4
The “V-Chip” screen will
appear, and “V-Chip
Lock” will be selected.
To enable the V-Chip
feature, press the
UP/DOWN
buttons
so that the “V-Chip
Lock” is set to Yes.
(Pressing the
UP/DOWN
buttons
will alternate between
“On” and “Off ”.)
Press the EXIT button
to exit.
English-63
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 64
O P E R AT I O N
How to Set up Restrictions Using the ‘TV Parental Guidelines’
First, set up a personal identification number (PIN), and enable the V-Chip.
(See previous section.) Parental restrictions can be set up using either of two methods:
The TV guidelines or the MPAA rating.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the
UP/DOWN
buttons
to select “V-Chip”, then
press the ENTER
button.
3
The “Enter Pin” screen
will appear. Enter your
4-digit Pin number.
Note: The default Pin
number for a new TV
set is “0-0-0-0.”
4
Press the
UP/DOWN
buttons to
select “TV Parental
Guidelines”, then press
the ENTER
button.
Note: These categories consist of
two separate groups : TV-Y and
TV-Y7 (young children through
age 7), and TV-G through TV-MA
(everybody else).
The restrictions for these two
groups work independently:
If a household includes very young
children as well as young adults,
the TV guidelines must be set up
separately for each age group.
(See next step.)
5
The “TV Parental Guidelines”
screen will appear.
Press the UP/DOWN
buttons to select one of
the six age-based categories:
TV-Y Young children
TV-Y7 Children 7 and over
------------------------------TV-G General audience
TV-PG Parental guidance
TV-14 Viewers 14 and over
TV-MA Mature audience
English-64
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 65
O P E R AT I O N
5
At this point, one of the TV-Ratings is selected.
Depending on your existing setup, the color of the letter “U” or “B” will be highlighted
(changed to yellow). (U= Unblocked, B= Blocked)
When the color of the “U” or “B” is changed, press the ENTER(
category.
To select a different TV-Rating, press the UP/DOWN
To EXIT this screen, press MENU(
)button to block or unblock the
buttons and then repeat the process.
) again.
Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options.
See the next step to change any of the following sub-ratings:
FV
D
L
S
V
: Fantasy Violence
: Sexual suggestive Dialog
: Adult Language
: Sexual situation
: Violence
Note 2: The V-Chip will automatically block certain categories that are “more restrictive.”
For example, if you block “TV-Y” category, then TV-Y7 will automatically be blocked.
Similarly, if you block the TV-G category, then all the categories in the “young adult”
group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V)
work together similarly. (See next section.)
6
How to set the FV, D, L, S and V sub-ratings.
First, select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous
page).
Next, while the TV-Rating is selected, repeatedly press the LEFT or RIGHT buttons.
This will cycle through the available sub-ratings (FV,L, S, D or V).
A highlighted letter (“U” or “B”) will be displayed for each sub-rating. While the “U” or “B” is
highlighted, press the ENTER( ) button to change the sub-rating.
Press MENU(
) once to save the TV guidelines.
To select a different TV-Rating, press the UP/DOWN
To exit this screen, press MENU(
buttons and then repeat the process.
) once again.
Note: The V-chip will automatically block certain categories that are “More restrictive”.
For example, if you block the “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14
andTV-MA will automatically be blocked.
7
Press the MENU button to clear all the screens.
(Or proceed to the next section, and set up additional restrictions based on the MPAA codes).
English-65
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 66
O P E R AT I O N
How to Set up Restrictions Using the MPAA Ratings:
G, PG, PG-13, R, NC-17, X
The MPAA rating system uses the Motion Picture Association of America (MPAA) system,
and its main application is for movies.
When the V-Chip lock is on, the TV will automatically block any programs that are coded
with objectionable ratings (either MPAA or TV-Ratings).
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select “V-Chip”,
then press the ENTER
button.
2
The “Enter Pin” screen
will appear. Enter your
4-digit PIN number.
Note: The default Pin
number for a new TV
set is “0-0-0-0.”
3
Press the
UP/DOWN
buttons
to select “MPAA rating”,
then press the ENTER
button.
English-66
BN68-00653A-01Eng.qxd
5/7/04 9:05 AM
Page 67
O P E R AT I O N
G
General audience (no restrictions).
4
PG
Parental guidance suggested.
Repeatedly press the
UP/DOWN
buttons
to select a particular
MPAA category. (When a
category is selected, its
color changes to yellow.)
PG-13 PG-13 (Parents strongly cautioned).
R
R (Restricted. Children under 17
should be accompanied by an adult).
NC-17 No children under age 17.
X
X (Adults only).
NR
Not rated.
Press the ENTER( ) button to select “U” or “B”.
Press the MENU( )button four times to save the settings and to clear all screens.
Note: The V-Chip will automatically block any category that is “more restrictive”.
For example, if you block the “PG-13” category, then “R,” “NC-17,” and “X”will
automatically be blocked also.
How to Reset the TV after the V-Chip
Blocks a Channel (‘Emergency Escape’)
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and
the following message will appear: “Excessive rating”.
To resume normal viewing, tune to a different channel using the number buttons. Under certain
conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the
channels.
In this case, use the Menu button for an “emergency escape”:
Select the V-Chip on the Menu. Enter your PIN number, and press the ENTER
temporarily disable the V-Chip Lock.
English-67
button to
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 68
O P E R AT I O N
Color Weakness
This feature enables those with a color weakness to view images as
those with normal color vision do.The feature provides nine different color adjustment
layers for red, green and blue.
1
Press the MENU button to
display the on-screen menu.
Press the UP/DOWN
buttons to select “Setup”, then
press the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Color Weakness”, then press
the ENTER
button.
3
This function doesn’t work
when the Source is in PC mode,
or DNIe is in off mode.
Press the ENTER
button and then press
the UP/DOWN
buttons to select
“On”, then press
the ENTER
button.
4
Press the UP/DOWN
buttons to select
“Red”, “Green”, “Blue”.
Press the LEFT/RIGHT
buttons to decrease or
increase the value of
a particular item.
Press the EXIT button
to exit.
English-68
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 69
O P E R AT I O N
Selecting the Melody
You can hear a melody sound when the television is powered on or off.
1
Press the MENU button to
display the on-screen menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Melody”, then press
the ENTER
button.
3
Press the UP/DOWN
buttons to select
“Off” or “On”.
Press the EXIT button
to exit.
English-69
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 70
Chapter Five
PC D I S P L AY
Using Your TV as a Computer (PC) Display
How to Set up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below.
However, the actual screens on your PC will probably look different, depending upon
your particular version of Windows and your particular video card. Even if your actual
screens look different, the same, basic set-up information will apply in most cases.
(If not, contact your computer manufacturer or Samsung Dealer).
First, click on “Settings” on the
Windows start menu.
While “Settings” is highlighted,
move the cursor so that “Control
Panel” is highlighted.
When the control panel screen
appears, click on “Display” and a
display dialog-box will appear.
Navigate to the “settings” tab on
the display dialog-box.
The two key variables that apply
the TV-PC interface are “resolution”
and “colors.” The correct settings
for these two variables are:
* Size
(sometimes called “resolution”):
1280 x 768 pixels
If a vertical-frequency option exists
on your display settings dialog box,
the correct value is “60” or “60 Hz”.
Otherwise, just click “OK” and exit
the dialog box.
* See “Display Modes” on page 87.
English-70
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 71
PC D I S P L AY
How to Auto Adjust
Use the Auto Adjust function to have the TV set automatically adjust the video signals
the monitor receives. The function also automatically fine-tunes the settings and
adjusts the frequency values and positions.
Press the PC button on the remote control to select the PC mode.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select
“PC”, then press
the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Auto Adjust”,
then press the ENTER
button.
English-71
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 72
PC D I S P L AY
Adjusting the Screen Quality
The purpose of the picture quality adjustment is to remove or reduce picture noise.
If the noise is not removed by fine tuning alone, then do the frequency adjustments to
the utmost and fine tune again. After the noise has been reduced, re-adjust the picture
so that it is aligned on the center of screen.
Press the PC button on the remote control to select the PC mode.
Note:This function does not work in DVI-Digital mode.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select
“PC” then press the
ENTER
button.
2
Press the ENTER
button to select
“Image Lock”.
3
Press the UP/DOWN
buttons to select
“Coarse” or “Fine”,
then press the
ENTER
button.
Press the
LEFT/RIGHT
buttons to adjust the
screen quality, vertical
stripes may appear or the
picture may be blurry.
<Adjusting Coarse>
Press the EXIT button to
exit.
<Adjusting Fine>
English-72
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 73
PC D I S P L AY
Changing the Screen Position
Press the PC button on the remote control to select the PC mode.
1
Press the MENU button to
display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
2
Press the UP/DOWN
buttons to select
“PC”, then press
the ENTER
button.
Press the UP/DOWN
buttons to select
“Position”, then press
the ENTER
button.
3
Press the UP/DOWN
buttons to adjust
the V-Position.
Press the LEFT/RIGHT
buttons to adjust
the H-Position.
Press the EXIT button
to exit.
English-73
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 74
PC D I S P L AY
To Initialize the Screen Position or Color Settings
Press the PC button on the remote control to select the PC mode.
1
Press the MENU button
to display the menu.
Press the UP/DOWN
buttons to select “Setup”,
then press the ENTER
button.
Press the UP/DOWN
buttons to select
“PC”, then press
the ENTER
button.
2
Press the UP/DOWN
buttons to select
“Image Reset”, then press
the ENTER
button.
Press the EXIT button
to exit.
English-74
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 75
Chapter Six
TROUBLESHOOTING
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, call your nearest Samsung service center.
Identifying Problems
Problem
Poor picture
Possible Solution
Try another channel.
Adjust the antenna.
Check all wire connections.
Poor sound quality.
Try another channel.
Adjust the antenna.
No picture or sound.
Try another channel.
Press the TV/VIDEO button.
Make sure the TV is plugged in.
Check the antenna connections.
No sound or sound is too low First, check the volume of units connected to your TV
at maximum volume.
(digital broadcasting receiver, DTV, DVD, cable
broadcasting receiver, VCR, etc.). Then, adjust the TV
volume accordingly.
Picture rolls vertically.
Check all wire connections.
The TV operates erratically.
Unplug the TV for 30 seconds, then try operating it
again.
Make sure the wall outlet is working.
The TV won’t turn on.
Remote control malfunctions Replace the remote control batteries.
Clean the upper edge of the remote control
(transmission window).
Check the battery terminals.
Ensure that the signal cable is firmly connected to the
“Check Signal Cable”
PC sources.
message.
English-75
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 76
TROUBLESHOOTING
Problem
“Not Supported Mode!”
message.
The image is too light or too
dark.
Horizontal bars appear to
flicker, jitter or shimmer on
the image.
Vertical bars appear to flicker,
jitter or shimmer on the image.
Possible Solution
Check the maximum resolution and the frequency of
the Video Adapter.
Compare these values with the data in the Display
Modes Timing Chart.
Adjust the Brightness and Contrast.
Adjust the Fine tuning.
Adjust the Coarse tuning and then adjust the Fine
tuning.
Adjust the Coarse tuning and then adjust the Fine
tuning.
Screen is black and power
indicator light blinks steadily.
On your computer check: Power ,
Signal Cable(24-pin DVI)
The TV is using its power management system.
Move the computer's mouse or press a key on the keyboard.
Image is not stable and may
If the setting is not correct, use your computer utility
appear to vibrate.
program to change the display settings.
NOTE: Your TV supports multiscan display functions
within the following frequency domain:
• Horizontal frequency:
30 kHz ~ 61 kHz
• Vertical frequency:
56 Hz ~ 75 Hz
• Maximum refresh rate:
1280 x 768 @ 60 Hz
Image is not centered on the
Adjust the horizontal and vertical position.
screen.
The screen position must be adjusted on the output
source(i.e.. STB) with a digital signal.
If a still image is displayed for When you need to leave the monitor unused for an
an extended period of time,
extended period of time, adjust the settings so that the
residual images or blurring
monitor automatically goes into energy saving mode or
may appear.
activates the screen saver to display moving images.
English-76
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 77
TROUBLESHOOTING
Problem
Possible Solution
The Anynet does not function.
Check to see if the device is an Anynet device.
The Anynet System supports only Anynet-enabled devices.
The Anynet System supports up to one device from the
Receiver product group and two devices from the DVD
product group. Check to see if the Anynet devices are plugged
in properly.
The remote control doesn’t
work.
Check to see if the angle and the distance between the remote
control and the device are appropriate and if there is any obstacle
in the path between the remote control and the device.
Replace the remote control batteries.
Check to see if you selected the correct device (TV, DVD,
VCR, cable or STB) to control using the [Mode] button.
Check to see if the remote control mode matches the input mode.
See if you pressed the correct function button.
Be sure to note that there are buttons on the remote control
that are not available depending on the device mode.
I would like to start the
Anynet.
See if the Anynet devices are connected to the TV according
to the connection diagram and make sure the proper Anynet
Connection Setting has been selected.
Press the [Mode] button on the TV remote control to
set the mode to TV.
Then, press the [Anynet] button to bring up the Anynet menu
and choose a what AV device you want to see.
I would like to exit the
Anynet.
Press [TV/Input] button on the TV remote control.
Turn the TV off.
I would like to bring up the
TV menu while using the
Anynet.
If you press the [Menu] button while you are using the Anynet
Watch function, it can bring up the DVD menu, VCR menu or
the Set-Top Box menu.
To view the TV menu, go to Anynet “Settings” and select
“TV Menu.”
Press the Menu button on the front of the TV.
English-77
BN68-00653A-01Eng.qxd
5/7/04 9:06 AM
Page 78
TROUBLESHOOTING
Problem
I would like to turn the
Anynet device off.
Possible Solution
Press the [Power] button on the TV remote control while
usingthe Anynet Watch function and the Anynet device that
was automatically turned on by the Anynet System is turned
off. (However, you cannot turn the device off in this manner if
it was turned on manually.)
Press the Input button while using the Anynet Watch function
and all Anynet devices except for the TV are turned off.
Select a different Watch menu item while using the Anynet
Watch function and the Anynet device you have been watching
is turned off.
Can’t use Anynet.
To change the remote control to Anynet mode,be sure to press
the “Mode”button on the TV remote control to change to TV
mode first.
Can’t use (name of device).
Check to see if the power code of the device is plugged in
properly.
Check to see if the Anynet devices are connected properly
according to the instructions.
Can’t use in the current mode.
The key is not supported in the current mode.
Anynet operating…
You cannot use the keys on the remote control while the Anynet
settings are being adjusted or during a Watch TV or Watch STB.
Try the keys again after the application of the new Anynet
settings or the mode switch is complete.
You cannot turn the device
that is currently recording off.
The device that is currently recording is not turned off when
you press the power button.
To turn a device that is currently recording off, use the remote
control of such device or the button on the front of the device.
English-78
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 79
TROUBLESHOOTING
Problem
Possible Solution
See if there are Anynet devices connected.
The Anynet System supports only Anynet devices.
Check to see if the Anynet devices connected are plugged in
properly.
Check to see if the Anynet devices are connected properly
according to the Anynet connection diagram. (Make sure that
the Output port of the TV is connected to the Input port of the
Anynet device and the Output port of the Anynet device is
connected to the Input port of the other Anynet device.)
Connect the video cable of the device to the TV according to the
connection diagram.
Then go to [Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
Check to see if the video cable is damaged. Then go to [Settings]
in the Anynet menu and select [Basic Connection Setting] or
[Advanced Connection Setting].
If the video cables are connected properly, set the input source to
the Anynet device (Combo) using the Input button on the remote
control and see if the display works properly. If it does not work
properly, see Troubleshooting for such device (Combo).
Check to see if the device is plugged in properly.
Then go to [Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
Check to see if the cables are connected properly according to
the instructions.
Then go to [Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
If the device is connected properly, turn the TV off and go to
[Settings] in the Anynet menu and select [Basic Connection
Setting] or [Advanced Connection Setting].
Check to see if two or more of the same type of device are
connected and if so, remove all such devices but one.
The Anynet System does not function when more than one of the
same type of device is connected.
Check the number of the Anynet devices connected and connect
the devices properly according to the connection diagram.
Then go to [Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
(The Anynet System supports up to one device from the Receiver
product group and two devices from the DVD product group.)
English-79
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 80
TROUBLESHOOTING
Problem
Possible Solution
Make sure that the devices connected support the Anynet.
Remove devices from the new Anynet product groups that
are not supported by the Anynet version currently running on
your TV.
Then go to [Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
Connect the video cable of the device to the TV according to the
connection diagram before use.
Check to see if the video cable is connected to the same place
now as it was at the time you selected the Connection Setting.
To re-connect the video cable to a different location, re-select the
Connection Setting and choose a device to watch.
If the TV is in VCR mode, see if the tape has any noise.
The device may not be able to detect the video signal if the noise
level is high.
Connect the video cables of the VCR properly according to the
connection diagram.
Then go to [Anynet Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
(After selecting the connection settings, make sure that the
Anynet device is selected for VCR viewing in the pop-up
window.)
If the cables are connected properly, see if the video cable of the
VCR is damaged.
Check to see if the power cord of the device is plugged
in operly.
Check to see if the Anynet devices are connected properly
according to the instructions.
See if there are Anynet devices connected.
The Anynet System supports only the Anynet devices.
If you have Anynet devices to connect, connect the devices
properly according to the connection diagram.
Then go to [Anynet Settings] in the Anynet menu and select
[Basic Connection Setting] or [Advanced Connection Setting].
You cannot use the “ Play DVD ” or “Play VCR ” functions
while the device is recording. Stop the recording before you use
the “Play” functions.
English-80
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 81
TROUBLESHOOTING
Glossary
Content
The Anynet System
A system that allows controlling Samsung AV devices from the TV.
Watch TV Broadcast
When selected, this Anynet menu item automatically executes the steps
involved in watching TV broadcasts on TV.
Play DVD
When selected, this Anynet menu item automatically executes the steps involved
in watching DVD titles on TV.
Watch Satellite
When selected, this Anynet menu item automatically executes the steps involved
in watching satellite programs on TV.
Switch to TV Remote
Control Mode
Select this menu item to switch the mode of the remote control to TV mode.
Basic Connection Setting
A menu item to configure the system setting before using the Anynet System.
(In setting up the Anynet System, use the connectors provided with the
purchase of the products or buy separate video connectors to connect the
devices.)
Advanced Connection
Setting
A menu item to configure the system setting before using the Anynet System.
(Choose this menu item when you use optical connectors to connect the
Anynet devices.)
Select Audio Input Port
Use this menu item to select the port on the TV or the Receiver to which
you connected the audio input port of the device during the Anynet system
configuration.
RS232C cable
Used to transmit signals to the TV and other peripheral devices.
OPTICAL
Optical digital output port. The simple connection helps protect the device
from electric interference, reducing the loss of electricity. It also allows
accurate sound reproduction.
COAXIAL
Coaxial digital output port. Allows high capacity data transmission with
minimum data loss and the resulting strong noise reduction capability allows
accurate sound reproduction.
Subwoofer
Complements the low-sound reproduction capability of the front speakers.
English-81
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 82
APPENDIX
Installing the Stand
<1>
<2>
1
Lower the TV set in the direction of the arrow and fix the stand.
2
Use the four screws to tightly fix the stand.
Maintenance of Your LCD TV
WARNING: To avoid risk of electric shock, do not disassemble the TV cabinet (except for gaining
access to the cable connectors as described on Chapter 2). Users cannot service the TV.
User maintenance is restricted to cleaning as explained below:
Unplug the LCD TV from the power outlet before cleaning.
• To clean your flat panel display screen, lightly dampen a soft, clean cloth with water or mild
detergent. If possible, use a special screen cleaning tissue or solution suitable for the antistatic coating.
• To clean the LCD TV cabinet, use a cloth lightly dampened with a mild detergent.
• Never use flammable cleaning material to clean your LCD TV or any other electrical apparatus.
English-82
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 83
APPENDIX
Wall Mount Installation Guide
1. This Wall Mount is designed for Samsung’s 32” LCD TV models and is sold separately.
2. Have a Samsung dealer install the Wall Mount.
3. Two or more people are required for installation.
4. Samsung is not responsible for any product damage or any injury
caused by installation at the customer’s discretion.
Parts
For wall mount installation, only the components and parts provided should be used.
Wall Mount Bracket
Side Hinges
Side Brackets
Support Bars
Screws
Hangers : 4 EA
Screws1 : 4 EA
Screws2 : 12 EA
Screws3 : 4 EA
Left
Left
Right
Right
How to Assemble the Wall Mount
1.Wall Mount Set is provided in individual parts, assembly is required for further installation.
2. Assemble the Side Brackets and
Assemble the Wall Mount Bracket and Hinges as illustrated in the direction of arrows, and
Support Bars as illustrated, and
secure the Captive Screws.
secure the screws. (12 screws (2) are
Secure the Wall Mount Bracket on the wall after securing the screws.
provided. For the safety, be sure to
secure all 12 screws.)
Side Hinges
(Left)
Side Hinges
(Right)
4.Firmly secure the Hanger Holders
3.Assemble the screws (1) and the Hanger Holders
as illustrated.
(that is completed at step 3) onto the
rear of the Wall Mount Bracket.
English-83
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 84
APPENDIX
How to Secure the LCD TV to the Wall Mount
1.Attach the assembled left/right Side Brackets onto the
2. Insert 4 Hangers into the grooves of the Wall Mount Bracket
rear side of the TV set and secure the screws(3).
and then push the Hangers downwards to mount the TV set
firmly. Be sure that the Hangers are firmly fixed onto the Wall
Mount Bracket after mounting the TV set.
How to Adjust the Angle of the Wall Mount
Before the installation of the Wall Mount Bracket onto the wall, adjust the angle to 0°.
1.Hold onto the topside of the TV set and pull it in
direction of arrows to adjust the angle. Hold onto the
middle of the TV’s topside for the angle adjustment.
Installation Dimensions
English-84
2.The angle can be adjusted by 0 ~ 20°.
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 85
APPENDIX
Cleaning and Maintaining Your TV
With proper care, your TV unit will give you many years of service.
Please follow these guidelines to get the maximum performance from your TV.
Placement
•
•
•
•
Do not place the TV near extremely hot, cold, humid or dusty places.
Do not place the TV near appliances with electric motors that create magnetic fields,
such as vacuum cleaners.
Keep the ventilation openings clear; do not place the TV on a soft surface,
such as cloth or paper.
Place the TV in a vertical position only.
Liquids
•
Do not handle liquids near or on the TV.
Liquids that spill into it can cause serious damage.
Cabinet
•
•
•
Never open the cabinet or touch the parts inside.
Wipe your TV with a clean, dry cloth.
Never use water, cleaning fluids, wax, or chemicals.
Do not put heavy objects on top of the cabinet.
Temperature
•
If your TV is suddenly moved from a cold to a warm place, unplug the power cord,
and allow at least two hours for moisture that may have formed inside the unit to dry
completely.
Using Your TV in Another Country
If you plan to take your TV with you to a foreign country, please be aware of the
different television systems that are in use around the world. A TV designed for one
system may not work properly with another system due to differences in the TV channel
frequencies.
English-85
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 86
APPENDIX
Specifications
Model Name
LT-P326W
Panel
Size
Display Size (HxV)
Type
Pixel Pitch
Viewing Angle
32.0” Diagonal
27.06 x 16.24 inches (687.36 x 412.42 mm)
a-si TFT active matrix
0.537 (H) x 0.537 (V) mm
170/170 (H/V)
*Frequency
Horizontal
Vertical
Display Color
30 ~ 61 kHz
56 ~ 75 Hz
16,777,216 colors
Maximum Mode
1280 x 768 @ 60 Hz
Input Signal
Sync Signal
Video Signal
H/V Separate, TTL, P. or N.
0.7 Vp-p @ 75 ohm
Video
Color System
Video System
NTSC
CVBS, S-VHS
Component
Video In
Audio In
1.0 Vp-p @ 75 ohm
500mVrms
Power Supply
Input
AC 120V ~ 60 Hz
Power
Consumption
Normal
Power Saving
180 W
< 5.0 W
Dimensions /
Weight
Unit (WxDxH): body
33.93 x 4.95 x 23.01 inches
(862.0 x 125.8 x 584.7 mm)
With Stand
33.93 x 12.91 x 23.86 inches / 50.70 lbs
(862.0 x 328.0 x 606.2 mm / 23.0 kg)
Environmental
Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
50 °F to 104 °F (10 °C to 40 °C)
10% to 80%, non-condensing
-4 °F to 113 °F (-20 °C to 45 °C)
5% to 95%, non-condensing
Audio
Characteristics
Audio Input 1
Audio Input 2
Headphone Out
Frequency
Response
RCA Jac (R, L), 0.5Vrms (-9dB)
3.5ø Stereo Jack, 0.5Vrms (-9dB)
Max. 10mW Output (3.5ø Stereo Jack 32Ω)
RF: 80Hz ~ 15kHz (at- 3dB)
A/V: 80Hz ~ 20kHz (at - 3dB)
Display
Resolution
* Referring to Display Modes, page 87.
English-86
BN68-00653A-01Eng.qxd
5/7/04 9:07 AM
Page 87
APPENDIX
Display Modes
If the signal from the system equals the standard signal mode, the screen is adjusted
automatically. If the signal from the system doesn’t equal the standard signal mode,
adjust the mode by referring to your Videocard user guide; otherwise there may be no
video. For the display modes listed below, the screen image has been optimized during
manufacture.
Mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H/V)
Macintosh
640 X 480
35.000
66.667
30.240
-/-
832 X 624
49.726
74.551
49.500
+/+
640 X 480
31.496
59.940
25.175
-/-
720 X 400
31.469
70.087
28.322
-/-
IBM
VESA
GTF
640 X 480
37.861
72.809
31.500
-/-
640 X 480
37.500
75.000
31.500
-/-
800 X 600
37.879
60.317
40.000
+/+
800 X 600
48.077
72.188
50.000
+/+
800 X 600
46.875
75.000
49.500
+/+
1024 X 768
48.363
60.004
65.000
-/-
1024 X 768
56.476
70.069
75.000
-/-
1024 X 768
60.023
75.029
78.750
+/+
1280 X 768
47.700
60.000
80.136
-/+
English-87
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising