HA0605b Gesswein Stay Clean Liquid Flux SDS

HA0605b Gesswein Stay Clean Liquid Flux SDS
Gesswein SDS# – HA0605b
SAFETY DATA SHEET
1. Identification
Product identifier
STAY CLEAN® LIQUID SOLDERING FLUX, Product Numbers 8302300, 8302350
Other means of identification
SDS number
0099
Product Type
Liquid flux
Recommended use
Soldering of metal.
Recommended restrictions
None known.
Manufacturer/Importer/Supplier/Distributor information
Supplier
Paul H. Gesswein & Co., Inc.
201 Hancock Ave., Bridgeport, CT 06605
Phone: 203-366-5400, FAX 203-366-3953
email: [email protected]
Emergency Telephone
CHEMTELL - 800-255-3924
2. Hazard(s) identification
Physical hazards
Not classified.
Health hazards
Acute toxicity, oral
Category 4
Acute toxicity, inhalation
Category 4
Skin corrosion/irritation
Category 1
Serious eye damage/eye irritation
Category 1
Specific target organ toxicity, single exposure Category 1 (optic nerve)
Specific target organ toxicity, single exposure Category 3 respiratory tract irritation
OSHA defined hazards
Not classified.
Label elements
Signal word
Danger
Hazard statement
Harmful if swallowed. Harmful if inhaled. Causes severe skin burns and eye damage. May cause
respiratory irritation. Causes damage to organs (optic nerve).
Precautionary statement
Prevention
Do not breathe mist or vapor. Wash thoroughly after handling. Do not eat, drink or smoke when
using this product. Use only outdoors or in a well-ventilated area. Wear protective
gloves/protective clothing/eye protection/face protection.
Response
If swallowed: Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediately all
contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person to fresh air and
keep comfortable for breathing. If in eyes: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison
center/doctor. Specific treatment (see this label). Wash contaminated clothing before reuse.
Storage
Store in a well-ventilated place. Keep container tightly closed. Store locked up.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise
classified (HNOC)
None known.
3. Composition/information on ingredients
Mixtures
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
1 / 10
Chemical name
CAS number
%
Ammonium chloride
12125-02-9
5-25
Zinc chloride
7646-85-7
<30
Hydrochloric acid
7647-01-0
<5
67-56-1
<5
Methanol
Composition comments
All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in
percent by volume.
4. First-aid measures
Inhalation
Skin contact
Eye contact
Ingestion
Most important
symptoms/effects, acute and
delayed
Indication of immediate
medical attention and special
treatment needed
General information
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Oxygen or
artificial respiration if needed. Call a POISON CENTER or doctor/physician if you feel unwell.
Take off immediately all contaminated clothing. Rinse skin with water/shower. Call a physician or
poison control center immediately. Chemical burns must be treated by a physician. Wash
contaminated clothing before reuse.
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Call a physician or poison control center immediately.
Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If
vomiting occurs, keep head low so that stomach content doesn't get into the lungs.
Symptoms of inhalation over-exposure may include sore throat, choking, coughing, difficulty
breathing. Lung damage may occur after severe inhalation exposures. Depending on the duration
and concentration of over-exposure, skin or eye contact with this product can irritate and burn
contaminated tissue. Ingestion overexposure may be harmful or fatal. Prolonged or repeated
inhalation over-exposure may cause burns and ulcers to the nose and throat, dental erosion,
bronchitis, and stomach pains. Repeated or prolonged over-exposure to this product may result in
dermatitis (red, dry, itchy skin) and ulceration.
Dermatitis, other skin disorders, and respiratory conditions may be aggravated by over-exposure to
this product.
Keep victim under observation. Chemical burns: Flush with water immediately. While flushing,
remove clothes which do not adhere to affected area. Call an ambulance. Continue flushing during
transport to hospital. Pulmonary function tests, chest X-rays, and nervous system evaluations may
prove useful. Consultation with an ophthalmologist is recommended if eye exposure leads to tissue
damage. In case of shortness of breath, give oxygen. Symptoms may be delayed.
If you feel unwell, seek medical advice (show the label where possible). Ensure that medical
personnel are aware of the material(s) involved, and take precautions to protect themselves. Show
this safety data sheet to the doctor in attendance.
5. Fire-fighting measures
Suitable extinguishing media
Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2). Halons.
Unsuitable extinguishing
media
None known.
Specific hazards arising from
the chemical
This product is acidic and presents a contact hazard to firefighters. During a fire, irritating and toxic
gases (e.g., carbon monoxide, carbon dioxide, hydrogen chloride, nitrogen and zinc oxides, and
ammonia) may be generated.
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Special protective equipment
and precautions for firefighters
Fire fighting
equipment/instructions
Move containers from fire area if you can do so without risk.
Specific methods
Use standard firefighting procedures and consider the hazards of other involved materials.
General fire hazards
No unusual fire or explosion hazards noted. This product is neither flammable nor reactive under
normal circumstances; however, it may generate flammable hydrogen gas upon contact with
metals.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor. Do
not touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ensure adequate ventilation. Local authorities should be advised if significant spillages cannot be
contained. For personal protection, see section 8 of the SDS.
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
2 / 10
Methods and materials for
containment and cleaning up
This product is miscible in water. This material is classified as a water pollutant under the Clean
Water Act and should be prevented from contaminating soil or from entering sewage and drainage
systems which lead to waterways.
Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth
and place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
Environmental precautions
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.
Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Avoid
discharge into drains, water courses or onto the ground. Inform appropriate managerial or
supervisory personnel of all environmental releases.
7. Handling and storage
Precautions for safe handling
Conditions for safe storage,
including any incompatibilities
Do not breathe mist or vapor. Provide adequate ventilation. Do not use in areas without adequate
ventilation. Do not get in eyes, on skin, or on clothing. Avoid prolonged exposure. Do not taste or
swallow. When using, do not eat, drink or smoke. Use only outdoors or in a well-ventilated area.
Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Handle
and open container with care. Observe good industrial hygiene practices. Avoid release to the
environment.
Store locked up. Store in original tightly closed container. Store away from direct sunlight, sources
of intense heat, or where freezing is possible. Store in a well-ventilated place. Store away from
incompatible materials (see Section 10 of the SDS). Material should be stored in secondary
containers or in a diked area, as appropriate. Storage and use areas should be covered with
impervious materials.
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components
Type
Value
Hydrochloric acid (CAS
7647-01-0)
Ceiling
7 mg/m3
Methanol (CAS 67-56-1)
PEL
Zinc chloride (CAS
7646-85-7)
Form
PEL
5 ppm
260 mg/m3
200 ppm
1 mg/m3
Fume.
Components
Type
Value
Form
Ammonium chloride (CAS
12125-02-9)
STEL
20 mg/m3
Fume.
TWA
Ceiling
10 mg/m3
2 ppm
Fume.
STEL
TWA
STEL
250 ppm
200 ppm
2 mg/m3
Fume.
TWA
1 mg/m3
Fume.
US. ACGIH Threshold Limit Values
Hydrochloric acid (CAS
7647-01-0)
Methanol (CAS 67-56-1)
Zinc chloride (CAS
7646-85-7)
US. NIOSH: Pocket Guide to Chemical Hazards
Components
Type
Value
Form
Ammonium chloride (CAS
12125-02-9)
STEL
20 mg/m3
Fume.
TWA
Ceiling
10 mg/m3
7 mg/m3
Fume.
STEL
5 ppm
325 mg/m3
Hydrochloric acid (CAS
7647-01-0)
Methanol (CAS 67-56-1)
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
3 / 10
US. NIOSH: Pocket Guide to Chemical Hazards
Components
Value
Form
STEL
250 ppm
260 mg/m3
200 ppm
2 mg/m3
Fume.
TWA
1 mg/m3
Fume.
Type
TWA
Zinc chloride (CAS
7646-85-7)
Biological limit values
ACGIH Biological Exposure Indices
Components
Value
Determinant
Methanol (CAS 67-56-1)
15 mg/l
Methanol
Specimen
Sampling Time
Urine
*
* - For sampling details, please see the source document.
Exposure guidelines
US - California OELs: Skin designation
Methanol (CAS 67-56-1)
Can be absorbed through the skin.
US - Minnesota Haz Subs: Skin designation applies
Methanol (CAS 67-56-1)
Skin designation applies.
US - Tennessee OELs: Skin designation
Methanol (CAS 67-56-1)
Can be absorbed through the skin.
US ACGIH Threshold Limit Values: Skin designation
Methanol (CAS 67-56-1)
Can be absorbed through the skin.
US. NIOSH: Pocket Guide to Chemical Hazards
Methanol (CAS 67-56-1)
Can be absorbed through the skin.
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
Appropriate engineering
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
controls
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Eye
wash facilities and emergency shower must be available when handling this product.
Individual protection measures, such as personal protective equipment
Chemical respirator with organic vapor cartridge and full facepiece.
Eye/face protection
Skin protection
Hand protection
Other
Wear neoprene or rubber gloves for routine industrial use.
Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.
Respiratory protection
Chemical respirator with organic vapor cartridge and full facepiece.
Thermal hazards
Wear appropriate thermal protective clothing, when necessary.
General hygiene
considerations
Keep away from food and drink. Always observe good personal hygiene measures, such as
washing after handling the material and before eating, drinking, and/or smoking. Routinely wash
work clothing and protective equipment to remove contaminants.
9. Physical and chemical properties
Appearance
Physical state
Liquid.
Form
Liquid. Liquid
Color
Clear colorless.
Odor
Slightly sweet.
Odor threshold
Not available.
pH
Acidic.
Melting point/freezing point
Not available.
Initial boiling point and boiling
range
Not available.
Flash point
Not flammable.
Evaporation rate
> 1 (nBuAc = 1).
Flammability (solid, gas)
Not available.
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
4 / 10
Upper/lower flammability or explosive limits
Not available.
Flammability limit - lower
(%)
Flammability limit - upper
(%)
Not available.
Explosive limit - lower (%)
Not available.
Explosive limit - upper (%)
Not available.
Vapor pressure
Not available.
Vapor density
4 (air = 1).
Relative density
1.32 (water = 1).
Solubility(ies)
Solubility (water)
Slightly soluble.
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature
Not available.
Decomposition temperature
Not available.
Viscosity
Not available.
Other information
Litmus paper will turn red upon contact with this product. The odor may also act as a distinguishing
characteristic of this product.
10. Stability and reactivity
Reactivity
The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability
Material is stable under normal conditions.
Possibility of hazardous
reactions
No dangerous reaction known under conditions of normal use.
Conditions to avoid
Contact with incompatible materials. Extreme temperatures.
Incompatible materials
Acid. alkalis and their carbonates, hydrogen cyanide, interhalogens, ammonium nitrate, potassium
chlorate, lead and silver salts. Strong oxidizing agents. Amines. Do not mix with other chemicals.
This product is neither flammable nor reactive under normal circumstances; however, it may
generate flammable hydrogen gas upon contact with metals.
Carbon dioxide (CO2). Nitrogen oxides (NOx). Ammonia. Hydrogen Chloride (HCl). Zinc oxides.
Hazardous decomposition
products
11. Toxicological information
Information on likely routes of exposure
Harmful if inhaled. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May
Inhalation
cause damage to organs by inhalation. If vapors, mists, or sprays of this product are inhaled, they
can irritate and burn the nose, throat, and respiratory system. Symptoms of inhalation
over-exposure may include sore throat, choking, coughing, and difficulty breathing. Prolonged or
repeated over-exposure may cause burns and ulcers to the nose and throat, dental erosion,
bronchitis, and stomach pains. It has been reported that a worker developed asthmatic symptoms
after performing soldering work with a flux containing Ammonium and Zinc Chlorides (components
of this product). It has been reported that inhalation of Methanol (a component of this product)
vapors in high concentrations can cause blindness. Severe inhalation overexposure may cause
pulmonary edema (a life-threatening accumulation of fluid in the lungs) or pneumonitis. Symptoms
of pulmonary edema (e.g., shortness of breath, chest pains) can be delayed for several hours
after exposure. Severe inhalation of vapors or fumes (as may occur if individuals are exposed in
poorly ventilated areas, such as confined spaces) may be harmful.
Skin contact
Causes severe skin burns. Depending on the duration and concentration of over-exposure, skin
contact with this product can irritate and burn the skin. Repeated or prolonged over-exposure to
this product may result in dermatitis (red, dry, itchy skin) and ulceration. Methanol (a component
of this product) is readily absorbed through the skin. Because Methanol is a minor component of
this product, skin absorption is not anticipated to be a significant route of over-exposure.
Eye contact
Depending on the duration and concentration of over-exposure, eye contact with this product can
irritate and burn the eyes. Eye over-exposure can cause pain, tearing, and redness. Severe eye
over-exposure may cause blindness. Causes serious eye damage.
Ingestion
Harmful if swallowed. Causes digestive tract burns. If this flux is ingested, nausea, vomiting, and
diarrhea may occur (depending on the amount of the product swallowed). Severe ingestion
exposures may result in damage to the tissues of the gastrointestinal system, and death.
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
5 / 10
Symptoms related to the
physical, chemical and
toxicological characteristics
Symptoms of inhalation over-exposure may include sore throat, choking, coughing, difficulty
breathing. Lung damage may occur after severe inhalation exposures. Depending on the duration
and concentration of over-exposure, skin or eye contact with this product can irritate and burn
contaminated tissue. Ingestion overexposure may be harmful or fatal. Prolonged or repeated
inhalation over-exposure may cause burns and ulcers to the nose and throat, dental erosion,
bronchitis, and stomach pains. Repeated or prolonged over-exposure to this product may result in
dermatitis (red, dry, itchy skin) and ulceration.
Dermatitis, other skin disorders, and respiratory conditions may be aggravated by over-exposure
to this product.
Information on toxicological effects
Acute toxicity
Components
Harmful if inhaled. Harmful if swallowed. May cause respiratory irritation.
Species
Test Results
Acute
Inhalation
LC50
Rat
3124 mg/l, 1 Hours
Oral
LD50
Rabbit
900 mg/kg
Acute
Inhalation
LC50
Rat
22500 ppm, 8 hours
Oral
LD50
Rat
6200 mg/kg
Hydrochloric acid (CAS 7647-01-0)
Methanol (CAS 67-56-1)
* Estimates for product may be based on additional component data not shown.
Causes severe skin burns and eye damage.
Skin corrosion/irritation
Serious eye damage/eye
irritation
Causes serious eye damage.
Respiratory or skin sensitization
Not a respiratory sensitizer.
Respiratory sensitization
It has been reported that a worker developed asthmatic symptoms after performing soldering work
with a flux containing Ammonium and Zinc Chlorides (components of this product).
Skin sensitization
This product is not expected to cause skin sensitization.
Germ cell mutagenicity
No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Carcinogenicity
This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
IARC Monographs. Overall Evaluation of Carcinogenicity
Hydrochloric acid (CAS 7647-01-0)
3 Not classifiable as to carcinogenicity to humans.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
This product is not expected to cause reproductive or developmental effects. Clinical studies on
Reproductive toxicity
test animals exposed to relatively high doses of Methanol and Zinc Chloride (components of this
product) indicate teratogenic effects and adverse reproductive effects.
Specific target organ toxicity single exposure
Causes damage to organs (optic nerve). May cause respiratory irritation.
Specific target organ toxicity repeated exposure
Not classified.
Aspiration hazard
Not an aspiration hazard.
Chronic effects
Prolonged inhalation may be harmful.
12. Ecological information
Ecotoxicity
Very toxic to aquatic life with long lasting effects.
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
6 / 10
Components
Species
Test Results
Hydrochloric acid (CAS 7647-01-0)
Aquatic
Fish
LC50
Western mosquitofish (Gambusia affinis) 282 mg/l, 96 hours
* Estimates for product may be based on additional component data not shown.
No data is available on the degradability of this product.
Persistence and degradability
Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
Methanol (CAS 67-56-1)
No data available.
Mobility in soil
Other adverse effects
-0.77
No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal instructions
Local disposal regulations
Hazardous waste code
Waste from residues / unused
products
Contaminated packaging
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Do not allow
this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches
with chemical or used container. Dispose of contents/container in accordance with
local/regional/national/international regulations.
Dispose in accordance with all applicable regulations.
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Empty containers should be taken to an approved waste handling site for recycling or disposal.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.
14. Transport information
DOT
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Label(s)
Packing group
Environmental hazards
Marine pollutant
Special precautions for user
Special provisions
Packaging exceptions
Packaging non bulk
Packaging bulk
IATA
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Label(s)
Packing group
Environmental hazards
Special precautions for user
IMDG
UN number
UN proper shipping name
UN1760
Corrosive liquids, n.o.s. (Zinc Chloride, Hydrochloric Acid)
8
8
III
Yes
Read safety instructions, SDS and emergency procedures before handling.
IB3, T7, TP1, TP28
154
203
241
UN1760
Corrosive liquids, n.o.s. (Zinc Chloride, Hydrochloric Acid)
8
8
III
Yes
Read safety instructions, SDS and emergency procedures before handling.
UN1760
Corrosive liquids, n.o.s. (Zinc Chloride, Hydrochloric Acid)
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
7 / 10
Transport hazard class(es)
Class
Subsidiary risk
Label(s)
Packing group
Environmental hazards
Marine pollutant
EmS
Special precautions for user
Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
8
8
III
Yes
Not available.
Read safety instructions, SDS and emergency procedures before handling.
Not established.
DOT Regulated Marine Pollutant. IMDG Regulated Marine Pollutant.
General information
15. Regulatory information
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
All components are on the U.S. EPA TSCA Inventory List.
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
CERCLA Hazardous Substance List (40 CFR 302.4)
Ammonium chloride (CAS 12125-02-9)
LISTED
Hydrochloric acid (CAS 7647-01-0)
LISTED
Methanol (CAS 67-56-1)
LISTED
Zinc chloride (CAS 7646-85-7)
LISTED
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Immediate Hazard - Yes
Hazard categories
Delayed Hazard - No
Fire Hazard - No
Pressure Hazard - No
Reactivity Hazard - No
SARA 302 Extremely hazardous substance
Chemical name
CAS number
Reportable
quantity
(pounds)
Threshold
planning quantity
(pounds)
Hydrochloric acid
500
7647-01-0
SARA 311/312 Hazardous
chemical
SARA 313 (TRI reporting)
Chemical name
Ammonium chloride
Zinc chloride
Hydrochloric acid
Methanol
5000
Threshold
planning quantity,
lower value
(pounds)
Threshold
planning quantity,
upper value
(pounds)
Yes
CAS number
% by wt.
12125-02-9
7646-85-7
7647-01-0
67-56-1
5-25
<30
<5
<5
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Hydrochloric acid (CAS 7647-01-0)
Methanol (CAS 67-56-1)
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Hydrochloric acid (CAS 7647-01-0)
Not regulated.
Safe Drinking Water Act
(SDWA)
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
8 / 10
Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR 1310.02(b) and 1310.04(f)(2) and
Chemical Code Number
Hydrochloric acid (CAS 7647-01-0)
6545
Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures (21 CFR 1310.12(c))
Hydrochloric acid (CAS 7647-01-0)
20 %WV
DEA Exempt Chemical Mixtures Code Number
Hydrochloric acid (CAS 7647-01-0)
6545
US state regulations
US. Massachusetts RTK - Substance List
Ammonium chloride (CAS 12125-02-9)
Hydrochloric acid (CAS 7647-01-0)
Methanol (CAS 67-56-1)
Zinc chloride (CAS 7646-85-7)
US. New Jersey Worker and Community Right-to-Know Act
Ammonium chloride (CAS 12125-02-9)
Hydrochloric acid (CAS 7647-01-0)
Methanol (CAS 67-56-1)
Zinc chloride (CAS 7646-85-7)
US. Pennsylvania Worker and Community Right-to-Know Law
Ammonium chloride (CAS 12125-02-9)
Hydrochloric acid (CAS 7647-01-0)
Methanol (CAS 67-56-1)
Zinc chloride (CAS 7646-85-7)
US. Rhode Island RTK
Ammonium chloride (CAS 12125-02-9)
Hydrochloric acid (CAS 7647-01-0)
Methanol (CAS 67-56-1)
Zinc chloride (CAS 7646-85-7)
US. California Proposition 65
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive
harm.
US - California Proposition 65 - Carcinogens & Reproductive Toxicity (CRT): Listed substance
Methanol (CAS 67-56-1)
International Inventories
Country(s) or region
Australia
Inventory name
Australian Inventory of Chemical Substances (AICS)
On inventory (yes/no)*
Yes
Canada
Domestic Substances List (DSL)
Canada
Non-Domestic Substances List (NDSL)
China
Inventory of Existing Chemical Substances in China (IECSC)
Yes
Europe
European Inventory of Existing Commercial Chemical
Substances (EINECS)
Yes
Europe
European List of Notified Chemical Substances (ELINCS)
Japan
Inventory of Existing and New Chemical Substances (ENCS)
Yes
Korea
Existing Chemicals List (ECL)
Yes
New Zealand
New Zealand Inventory
Yes
Philippines
Philippine Inventory of Chemicals and Chemical Substances
(PICCS)
Yes
United States & Puerto Rico
Toxic Substances Control Act (TSCA) Inventory
Yes
Yes
No
No
*A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s).
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
16. Other information, including date of preparation or last revision
Issue date
18-February-2015
Revision date
-
Version #
01
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
9 / 10
NFPA ratings
0
3
Disclaimer
0
Harris Products Group cannot anticipate all conditions under which this information and its
product, or the products of other manufacturers in combination with its product, may be used. It is
the user’s responsibility to ensure safe conditions for handling, storage and disposal of the
product, and to assume liability for loss, injury, damage or expense due to improper use. The
information in the sheet was written based on the best knowledge and experience currently
available.
STAY CLEAN® LIQUID SOLDERING FLUX
924591 Version #: 01 Revision date: - Issue date: 18-February-2015
SDS US
10 / 10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement