D-Link | DCS-5605 | User manual | D-Link DCS-5605 User manual

D-Link DCS-5605 User manual
Table of Contents
Package Contents.......................................................................3
System Requirements............................................................3
Introduction.............................................................................4
Hardware Overview................................................................6
Rear.................................................................................6
Front................................................................................7
Camera Installation.....................................................................8
Installation Wizard..................................................................9
Mounting............................................................................... 21
Using the Camera with a Router.......................................... 24
Configuration.............................................................................25
Live Video.............................................................................26
Overview........................................................................27
Setup.................................................................................... 29
Internet Connection Setup Wizard................................. 30
Network Setup............................................................... 34
LAN Settings...........................................................35
Port Settings...........................................................36
Wireless Setup (DCS-5635 only)................................... 37
Setting up a Wireless Connection with WPS.......... 39
Dynamic DDNS.............................................................. 40
Image Setup..................................................................41
Audio and Video............................................................ 42
Video Profiles..........................................................42
Enable External Speaker........................................42
Enable External Microphone................................... 42
Motion Detection............................................................ 44
Drawing Mode.........................................................45
Motion Detection Setup Wizard.............................. 46
Time and Date............................................................... 50
Preset Position............................................................... 51
D-Link DCS-5605/DCS-5635 User Manual
Recording......................................................................52
Record to SD Card..................................................52
Record to Samba Drive...........................................52
Snapshot........................................................................54
SD Card.........................................................................57
Advanced..............................................................................58
ICR.................................................................................58
Digital Output.................................................................59
External I/O Port.....................................................59
External Trigger Configuration................................ 60
Maintenance.........................................................................64
Admin.............................................................................64
Change Password...................................................64
Add/Delete User Accounts......................................64
Device Settings.............................................................. 65
Change Camera Name...........................................65
On-Screen Display..................................................65
Turn On/Off LEDs...................................................65
Calibrate Device......................................................65
System...........................................................................66
Firmware Upgrade......................................................... 67
Status................................................................................... 68
Device Info.....................................................................68
Log.................................................................................69
Help...................................................................................... 70
Appendix....................................................................................71
Frequently Asked Questions................................................71
How to Ping Your IP Address........................................ 74
Using & Configuring 3G Compatible Cell Phones................ 75
Play from RealPlayer..............................................76
Play from PVPlayer.................................................81
1
Reset and Restore................................................................83
Enabling UPnP™ for Windows® XP....................................... 84
Technical Specifications..........................................................88
Contacting Technical Support.................................................90
Warranty.....................................................................................91
Registration................................................................................94
D-Link DCS-5605/DCS-5635 User Manual
2
Package Contents
•
•
•
•
•
•
•
•
D-Link DCS-5605/5635 Wireless N PTZ Network Camera
12V/2A External Power Adapter
CAT5 Ethernet Cable
Quick Install Guide
CD-ROM
A/V Cable
Plate
Mounting Screws
Note: Using a power supply with a different voltage than the one included with the DCS-5605/DCS-5635 will cause damage and void the
warranty for this product. If any of the above items are missing, please contact your reseller.
System Requirements
•
•
•
•
Internet Explorer 6.0 or higher
Pentium 4, 2Ghz processor or higher
128MB RAM or higher
32MB AGP Video Card
D-Link DCS-5605/DCS-5635 User Manual
3
Introduction
A HIGH-PERFORMANCE SURVEILLANCE SOLUTION
The DCS-5605/DCS-5635 is a high performance camera for professional surveillance and remote monitoring. This network camera features
motorized pan, tilt, and optical/digital zoom for ultimate versatility. The 10x optical zoom lens delivers the level of detail necessary to identify
faces, license plate numbers, and other important details that are diffi cult to clearly distinguish using digital zoom alone.
ADVANCED VIDEO ENCODING
To maximize bandwidth efficiency and improve image quality, the DCS-5605/5635 offers real-time video compression in MJPEG, MPEG-4
and H.264 formats. The H.264 codec can reduce the size of a video stream by up to 80% compared to Motion JPEG. Thus, less network
bandwidth and storage space is required.
SURVEILLANCE ON THE GO
The DCS-5605/5635 supports 3GPP mobile surveillance. A live feed from the camera can be accessed on a 3G cellular network using a
compatible phone, PDA or mobile device capable of RTSP (Real Time Streaming Protocol) streaming. This enables you to monitor your
home or office space in real time even when you are on the go.
THE PERFECT MATCH FOR YOUR NETWORK
Two comparable models are available depending on your unique network requirements. The DCS-5605 includes an Ethernet port, while the
DCS-5635 offers both Ethernet and 802.11n wireless interfaces. The wireless model offers installation fl exibility and freedom of wireless
connectivity in difficult locations without the hassle of running Ethernet cables. The wireless camera supports WEP and WPA-PSK/TKIP
for establishing secure connections to your wireless network.
EASY TO INSTALL AND SIMPLE TO MANAGE
The DCS-5605/DCS-5635 can be mounted on a flat surface or with a metal wall mount. You can also set up automated e-mail alerts
to be instantly informed of unusual activities. In addition, this network camera supports the Universal Plug-n-Play feature, which allows
computers running on Windows® XP/Vista/7 to automatically recognize the camera and add it to the network. Sign up with one of the free
Dynamic DNS services available on the web, to assign a name and domain to the camera (for example, mycamera.dlinkddns.com). This
way, you may remotely access the camera without having to remember the IP address.
D-Link DCS-5605/DCS-5635 User Manual
4
•Supports a Variety of Protocols -In addition, the DCS-5605/DCS-5635 supports a variety of platforms including FTP, SMTP,
NTP, and HTTP. The camera also supports UPnP and DDNS. DDNS allows the camera to use an easier to remember naming
format rather than an IP address. UPnP will allow users of Windows® XP to install the camera with the click of a mouse.
•Broad Range of Applications - With today’s high-speed Internet services, the Camera can provide the ideal solution for live
video images and audio over the Intranet and Internet for remote monitoring. The DCS-5605/DCS-5635 allows remote access
from your Internet Explorer Web browser for live image viewing with audio, and allows the administrator to manage and control
the Camera anytime and anywhere in the world. Apply the Camera to monitor various objects and places such as homes, offices,
banks, hospitals, child-care centers, amusement parks and other varieties of industrial and public monitoring. The Camera can
also be used for intruder detection with its motion-detection mode, capture still images and video images for archiving, and many
more applications such as sending images to an FTP server or configuring for E-mail alerts. The DCS-5605/DCS-5635 features
2-way Full-Duplex audio with an external microphone (not included) that lets you remotely monitor and record audio with your
video. With the addition of optional speakers (not included), you can have 2-way Full-Duplex audio communication with the people
you are viewing. The DCS-5605/DCS-5635 also features 10x optical and digital zoom for closer viewing.
•A/V Output -The DCS-5605/DCS-5635 comes with an A/V output allowing you to connect to your TV for local viewing. The DCS5605/DCS-5635 can also be connected directly to your VCR to record activities.
Note: Audio Out from the A/V port is for connecting a speaker to the camera so that a person in front of the camera can hear the
person on the other end of the communication. Video out from the A/V port is for connecting to a TV for viewing the camera’s video
feed or VCR for recording purposes.
•Web Configuration - Using the Internet Explorer Web browser, administrators can configure and manage the Camera directly
from its own Web page via the Intranet or the Internet. Up to 20 user names and passwords are permitted, with privilege settings
controlled by the administrator.
•Powerful Surveillance and Remote Monitoring Utility - Assign an administrator with a pre-defined user ID and password who
can modify the Camera settings from the remote site via the Intranet or the Internet. Administrators are allowed to monitor the
image, record the image to a hard drive, and take snapshots.
•Connecting to External Devices - Supporting auxiliary Input/Output connectors, you can connect the Camera to a variety of
external devices such as IR-sensors, switches and alarm relays. Combined with programmable alarming equipments, you can
develop a variety of security applications that are triggered on alarm-based events. The Camera provides an industry standard
in/out external connector for connectivity.
Note: Use of audio or video equipment for recording the image or voice of a person without their knowledge and consent is prohibited in certain states or jurisdictions.
Nothing herein represents a warranty or representation that the D-Link product provided herein is suitable for the end-user’s intended use under the applicable laws of
his or her state. D-Link disclaims any liability whatsoever for any end-user use of the D-Link product, which fails to comply with applicable state, local, or federal laws.
D-Link DCS-5605/DCS-5635 User Manual
5
Hardware Overview
Rear
1
Micro SD Port
Insert a Micro SD memory card to save data from
the camera.
2
WPS (DCS-5635 Only)
Press the WPS button to automatically connect
to a WPS-enabled wireless router or access point
and establish connectivity.
3
Power Receptor
Plug in the supplied power adapter to an outlet.
4
Ethernet Port
Connect an Ethernet cable to a router, switch,
or computer.
5
I/O Connector
The camera provides a terminal block with two
pairs of connectors situated on the back panel.
One pair is for input and the other is for output.
The I/O connectors provide the physical interface
to send and receive digital signals to a variety of
external alarm devices. Please refer to the I/O
Connector section in this manual for detailed
information.
6
Plug the included A/V cable into the A/V out
Video/Audio Line-Out Port connector to use the camera with a television or
VCR, or connect to speakers.
7
External Microphone Port Insert an external microphone to record audio.
8
Reset Button
Press and hold for 10 seconds to reset the
camera back to the default settings.
D-Link DCS-5605/DCS-5635 User Manual
1
8
2
3
4
5
6
7
6
Front
1
2
4
3
1
Camera Lens
The IR-Cut Removable sensor judges lighting conditions and switches from color to infrared
accordingly.
2
WPS/Link LED
The WPS LED will blink blue when initializing a connection, and illuminate with solid blue
once the connection has been established (DCS-5635 only).
The Link LED will illuminate green once a connection has been established.
3
Microphone
The built-in microphone can be used capture audio from sources nearby the camera.
4
Power LED
The Power LED will illuminate red when the camera is receiving power.
D-Link DCS-5605/DCS-5635 User Manual
7
Camera Installation
It is recommended to connect the camera to your computer and configure it before mounting.
Step 1 - Connect an Ethernet cable to the network cable connector located on the DCS-5605/DCS-5635’s back panel and attach it to the
network.
Step 2 - Attach the supplied power supply to the power input connector located on the DCS-5605/DCS-5635’s back panel and connect the
other end to your wall outlet.
D-Link DCS-5605/DCS-5635 User Manual
8
Installation Wizard
Step 3 - Insert the D-Link CD. When the autorun screen appears, click Installation Wizard.
Step 4 - The Welcome screen will appear. Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
9
Step 5 - Click Yes to the license agreement to continue.
Step 6 - If you do not want to install the wizard into the default location, click Browse and select a new folder. Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
10
Step 7 - Click Finish to complete the installation. Uncheck the I would like to launch Setup Wizard SE box if you do not want to run the
wizard.
Step 8 - Now, click on ffdshow from the autorun screen. This will install the proper codecs that will allow you to playback video taken by
the DCS-5605/5635.
D-Link DCS-5605/DCS-5635 User Manual
11
Step 9 - Click I Agree to the license agreement to continue.
Step 10 -Select your language from the drop-down menu and then click OK.
D-Link DCS-5605/DCS-5635 User Manual
12
Step 11 -Click Next to continue.
Step 12 -Select the installation location and then click Next.
D-Link DCS-5605/DCS-5635 User Manual
13
Step 13 -Select the components you want to install and then click Next to continue.
Step 14 -Select the Start Menu folder and then click Next.
D-Link DCS-5605/DCS-5635 User Manual
14
Step 15 -Select the additional tasks you want to perform and then click Next to continue.
Step 16 -Select the speaker setup on your computer and then click Next.
D-Link DCS-5605/DCS-5635 User Manual
15
Step 17 -Click Install to continue.
Step 18 -Click Finish.
D-Link DCS-5605/DCS-5635 User Manual
16
Step 19 -Click on the D-Link Setup Wizard SE icon that was created in your Windows
Start menu.
Step 20 -The main screen will appear. Your camera should be displayed in the list. If it does not, then click the Search button. If your
camera does not appear, make sure the camera is connected to your computer correctly and is powered on.
D-Link DCS-5605/DCS-5635 User Manual
17
Step 21 -Next to Admin ID, enter admin. By default the current password is blank. Click the Change box and enter a new password
(recommended). Click Next to continue.
Step 22 -Click DHCP to allow your router or DHCP server assign the IP settings to the camera. If you want to manually assign the IP
settings, click Static and enter the IP address, subnet mask, default gateway, and DNS servers. Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
18
Step 23 -If you have the DCS-5635 wireless camera, setup the following wireless settings:
Wireless - Click the Enable radio button. If you do not want to use the wireless feature of the camera, click Disable.
Connection Mode - Select Infrastructure if you are connecting to a wireless router or access point. If you are connecting to a
wireless client, select Adhoc.
Network Name (SSID) - Enter the SSID or wireless network name. This must be the same name as on your wireless router or
access point.
Wireless Channel - If you select Infrastructure, select Auto since the wireless router or access point will select the channel
automatically.
Authentication - Select Open, Shared, WPA-PSK, or WPA2-PSK.
Encryption - Depending on Authentication, select the type of encryption.
Key - Enter the encryption key or passphrase.
Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
19
Step 24 -A summary window will display your settings. Click Restart to finish the installation.
Installation is complete. Please refer to page 25 for advanced features of this camera.
D-Link DCS-5605/DCS-5635 User Manual
20
Mounting
It is recommended to connect the camera to your computer and configure it before mounting. Refer to the Configuration section.
The holes will be covered but are perferated to be easily removed. Attach the plate to the camera before mounting. Turn the camera
clockwise (to the right) until it stops. Read the directions on the next page to mount to a wall or the ceiling.
D-Link DCS-5605/DCS-5635 User Manual
21
1. Use 3 screws to affix the metal mounting bracket to the ceiling.
2. Push the camera up onto the metal mounting bracket.
D-Link DCS-5605/DCS-5635 User Manual
22
3. Rotate the base of the camera to lock it onto the bracket.
4. Install the final screw so that the camera cannot be removed without the use of a tool.
D-Link DCS-5605/DCS-5635 User Manual
23
Using the Camera with a Router
If you connect your camera behind a router and want to view video from the Internet, you must open (forward) ports to your camera.
You will need to statically assign the IP address and network information in the camera. Some routers will allow you to set a “reservation”
and assign an IP address to the camera automatically. Please refer to your router documentation for more information.
After you have completed the setup of the DCS-5605/DCS-5635 outlined in the Quick Install Guide you will have an operating camera
that has an assigned IP Address. Because you are using a router to share the Internet with one or more PCs, the IP Address assigned
to the camera will be a local IP Address. This allows viewing within your Local Area Network (LAN) until the router is configured to allow
remote viewing of the camera over the Internet.
Step 1 - Log into the camera’s web-based configuration by entering its IP address in a web browser such as Internet Explorer.
Step 2 - Enter the username admin and enter your password.
Step 3 - The Live Video page will appear. Click the Setup tab and then click Network Setup on the left side. The following page will appear.
Step 4 - Click Static IP Address and then enter the IP Address, Subnet Mask,
Default Gateway (usually the IP address of your router), and the DNS servers.
Step 5 - At the bottom, write down the ports listed. If you have more than one
camera, you will need to have different port numbers for each. Enter the port
numbers and click Save Settings.
Step 6 - You must now log into your router and navigate to the page that allows
you to open or forward ports. Enter the listed ports and forward to the IP address
of your camera.
By default the HTTP Port is 80 (TCP) and the RTSP Port is 554 (TCP/UDP).
D-Link DCS-5605/DCS-5635 User Manual
24
Configuration
This section will show you how to configure your new D-Link camera using the web-based configuration utility.
To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the camera (192.168.0.1).
If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.
Enter admin for the User Name and then enter your password. Leave the password blank by default.
D-Link DCS-5605/DCS-5635 User Manual
25
Live Video
The image from the DCS-5605/DCS-5635 should be visible from the Live Video page on your computer monitor.
Clicking on any part of the image will cause the camera to reposition itself so that the point will be the center of the image.
Refer to the next page for an overview of all the options available on this page.
D-Link DCS-5605/DCS-5635 User Manual
26
Overview
Outer Ring: Click on the arrows on the outer ring to move the camara. Click the right arrow to move the camera
to the right, the up arrow to move the camera up, etc.
Home: Click the Home icon to move the camera to its home position.
Inner RIng: Click the left button to zoom in and click the right button to zoom out
Auto Focus: Click to allow the camera to focus automatically (recommended).
Manual Focus: Click to manually focus the camera. Use the - and + buttons to focus in and out.
Pan: Pans the camera one full cycle.
Patrol: Enables the Auto Patrol feature. Please refer to page 43 to configure preset locations.
Stop: Stops movement of the camera during pan.
Go To: Select a preset position from the drop-down menu to move the camera to.
Pan Speed: Select the speed at which the camera will pan (1-10, 10 = fastest).
Tilt Speed: Select the speed at which the camera will tilt (1-10, 10 = fastest).
SD Status: Displays the status of your Micro SD memory card. If you do not have a card inserted into the camera,
it will display as Invalid.
Language: Select your language from the drop-down menu.
D-Link DCS-5605/DCS-5635 User Manual
27
1
2
3
4
5
6
7
8
9
10
11
1 Video 1 - Click to use Video Profile 1. You can change the settings in the Setup > Audio and Video section.
2 Video 2 - Click to use Video Profile 2. You can change the settings in the Setup > Audio and Video section.
3 Video 3 - Click to use Video Profile 3. You can change the settings in the Setup > Audio and Video section.
4 Video 4 - Click to use Video Profile 4. You can change the settings in the Setup > Audio and Video section.
5 Full Screen - Click to view video at full screen. Press ESC to go back to normal view.
6 Snapshot - Click to take a snapshot of the current video. The image will pop up in a new window and you may save this image
to a local hard drive.
7 Record - Click to start recording video. Click again to stop recording.
8 Set Path - Click to select a folder to save video and snapshots.
9 Audio On/Off - This button toggles the built-in microphone on and off, allowing you to hear audio from the area surrounding
your camera. Audio is on by default.
10 Talking On/Off - This will toggle audio to a speaker (not included) connected to the camera’s Audio Out port. This can be used
to communicate with others near the camera.
11 Digital Output - Click to turn on digital output.
D-Link DCS-5605/DCS-5635 User Manual
28
Setup
Internet Connection Click to configure your camera’s network settings, Dynamic DNS settings, camera name, and date/time setup.
Setup Wizard: Refer to the next page.
Manual Internet Click to manually configure your camera. Refer to the Setup > Network Settings section.
Connection Setup:
Motion Detection Click to launch the Motion Detection wizard. You will be able to configure detection areas and where to send
Setup Wizard: the images (Email/FTP/folder).
Manual Motion Click to manually configure motion detection settings. Refer to the Setup > Motion Detection section.
Detection Setup:
D-Link DCS-5605/DCS-5635 User Manual
29
Internet Connection Setup Wizard
Click Next to continue.
Select DHCP Connection to allow a DHCP server (such
as a router) to automatically assign the network settings
to the camera.
Select Static IP Address to manually enter the camera’s
network settings.
Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
30
If you use the camera to connect directly to the Internet
with a PPPoE connection, you will need to enter the
username and password, which were given to you
when you set up your account with your Internet
Service Provider. If the camera is behind a router or
a gateway, you do not need to configure this setting.
Click Next to continue.
DDNS service synchronizes the public IP address of the
modem when it has been modified. The username and
password is required when using the DDNS service.
Server Address - Select the web address of your
Dynamic DNS service provider.
Host name - The domain name you have applied from
DDNS service.
User name - The account name of the DDNS service.
Password - The password for the account of the DDNS
service.
Verify Password - Enter your password again used
to connect to the DDNS server.
Timeout - You can setup how often the camera notifies
the DDNS server of its current global IP address. By
default this is 576 hours.
Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
31
Enter a name for your camera. Click Next to continue.
Configure the time zone and daylight savings on the
camera.
Time Zone - Select your time zone from the drop-down
menu.
Auto Daylight Saving - Select to automatically
adjusted according to the daylight saving time of the
selected time zone.
Set Date and Time Manually - Manually adjust and
set the date and time of daylight savings.
Offset - Select the time offset, if your location observes
daylight saving time.
Daylight Savings Dates - Sets the dates and time that
Daylight Savings begins and ends.
Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
32
Click Apply to finish.
D-Link DCS-5605/DCS-5635 User Manual
33
Network Setup
The Network Setup page will allow you to set the IP address, network settings, UPnP, and port information for your camera.
D-Link DCS-5605/DCS-5635 User Manual
34
LAN Settings
DHCP Click to allow a DHCP server on your network such as
Connection: a router to assign your camera IP settings.
Static IP Click to manually enter the network settings of your
Address: camera. You will need to enter data in the next 5 boxes.
Enter an IP address for your camera. This will be the IP
address to access the web-based configuration utility
IP Address: in the future.
Enter the subnet mask of your network.
Subnet Mask: Enter the gateway IP address. This is usually the IP
address of your router.
Default Gateway:
Enter the primary DNS server IP address. This is usually
the IP address of your router.
Primary DNS:
Enter a secondary DNS server IP address.
Secondary DNS: Check to enable UPnP (Universal Plug and Play). This will allow an icon representing the camera in My Network Places
in Windows.
Enable UPnP:
Check to enable UPnP Port Forwarding. If enabled, set the HTTP and RTSP ports below.
Enable UPnP Port
Forwarding: Enter the HTTP port for the camera. The default port is 80. If you have more than one camera, you must assign different
ports on each camera. This port is used to view the camera from the Internet.
External HTTP
Port: Enter the RTSP port. The default port is 554. RTSP (Real Time Streaming Protocol) is used for viewing video from a
RTSP client. Clients are available for your computer or mobile phone.
External RTSP
Port:
D-Link DCS-5605/DCS-5635 User Manual
35
Port Settings
HTTP Port: Enter the HTTP port for the camera. The default port is 80. If you have more than one camera, you must assign
different ports on each camera. This port is used to view the camera from the Internet.
RTSP Port: Enter the RTSP port. The default port is 554. RTSP (Real Time Streaming Protocol) is used for viewing video from
a RTSP client. Clients are available for your computer or mobile phone.
User Authentication: Check the User Authentication box to force user to enter a user name and password.
Save Settings: Click the Save Settings button to save and activate your changes.
D-Link DCS-5605/DCS-5635 User Manual
36
Wireless Setup (DCS-5635 only)
Enable Wireless: Check the box to enable the wireless features on the camera. If you are not going to use this camera on a wireless
network, it is recommented to uncheck this box.
Site Survey: Site survey will display a list of available wireless networks that the camera detects. Click the Scan button to search
for wireless networks. Once completed, the networks will be available in the drop-down menu. Click on the network
you want to connect to. Some of the fields below will automatically be populated with the network’s settings.
SSID: If you selected a network from the drop-down menu, the SSID, or name of the wireless network, will be displayed.
If you are manually entering the wireless settings, enter the SSID of your network.
D-Link DCS-5605/DCS-5635 User Manual
37
Wireless Mode: Select Infrastructure (connect to an access point or wireless router) or Ad-Hoc (connect directly to a wireless
client also in ad-hoc mode).
Channel: Enter the wireless channel of your wireless network. When connecting to an access point or wireless router, this
will automatically be set.
Authentication: Select the type of encryption/security. You must know the security settings of your wireless network. If you selected
a network from the drop-down menu, this will be automatically set.
Encryption: Select Enable or Disable. If you selected a network from the drop-down menu, this will be automatically set.
Key: Enter the security key or passphrase.
Save Settings: Click the Save Settings button to save and activate your settings. Allow up to 2 minutes to connect to your wireless
network.
The image to the right is an example of a wireless setup.
After clicking the Scan button, a list of networks were
displayed in the drop-down menu. The wireless network
called dlink was selected.
As a result, the following fields were automatically
populated:
SSID - dlink
Wireless Mode - Infrastructure
Channel - Auto
Authentication - WPK2-PSK
Encryption - TKIP
To access the network, the user must know the security
passphrase used on the network and enter it in the Key
field.
The signal strength will be display. The value will be
between 1 and 100, 100 being the best/strongest signal.
D-Link DCS-5605/DCS-5635 User Manual
38
Setting up a Wireless Connection with WPS
If your wireless access point or router supports push-button Wireless Protected Setup (WPS), you can quickly configure your wireless
network and camera without using the camera’s web interface.
After plugging the power adapter to your camera and the front status LED lights up, hold down the WPS button on the back of the camera
for 3 seconds. After pressing the button, it should start flashing blue.
Now press the WPS button on your router or access point within 1 minute to activate WPS and allow your devices to automatically
configure a wireless connection. After WPS is successfully activated, the WPS LED on your camera will stop flashing, and will light up
solid blue, then reboot.
Note: On some routers/access points, you may need to enter the web interface to activate WPS. Consult your product’s user manual for
further assistance.
D-Link DCS-5605/DCS-5635 User Manual
39
Dynamic DDNS
Dynamic DNS (Domain Name Service) is a method of keeping a domain name linked to a changing (dynamic) IP address. With most Cable
and DSL connections, you are assigned a dynamic IP address and that address is used only for the duration of that specific connection.
With the camera, you can setup your DDNS service and the camera will automatically update your DDNS server every time it receives a
different IP address. Depending on the service, this update may take a few hours.
Enable DDNS: Check the box to enable DDNS on the camera.
Server Address: Enter the DDNS server address or select from the drop-down menu.
Host Name: Enter your DDNS host name.
User Name: Enter your DDNS user name.
Password/Verify: Enter your DDNS password and again to verify.
Timeout: Enter the time (in hours) before the camera will disconnect from the DDNS server.
Status: Displays the current status.
D-Link DCS-5605/DCS-5635 User Manual
40
Image Setup
Brightness: Select the brightness level of the video. Higher the value the brighter the image.
Saturation: Select the saturation value. Higher value will make the colors more bold.
Contrast: Select the contrast value.
Sharpness: Select the sharpness value. Lower value will soften the image.
Frequency: Select 50Hz or 60Hz.
Flip: Vertically rotate the video 180o.
Mirror: Horizontally rotate the video 180o. Recommended to select if the camera is installed upside down on the ceiling.
B/W: Change the video to black and white.
D-Link DCS-5605/DCS-5635 User Manual
41
Audio and Video
Click the Audio and Video button on the left side of the Setup screen to access audio and video settings that affect how the audio and
video appears. You may configure 4 video profiles with different settings for your camera. Additionally, you may also configure the audio
(speakers and microphone) for your camera. Profile 3 is set as the default profile for snapshots, while profile 4 is the default for a mobile
phone or PDA.
Video Profiles
Enable External Speaker
Enable External Microphone
Video Profiles (1-4):
Encode Type: Select H264, JPEG, or MPEG4 encoding. Profile 4 will always be MPEG4.
Resolution: Select the resolution (size of the viewing area on the screen).
FPS: Select the FPS (Frames per Second). 30 is the maximum (best quality).
D-Link DCS-5605/DCS-5635 User Manual
42
BPS: Select the BPS (Bits per Second). This is the fixed bandwidth rate. Higher the value means better quality video but
requires more bandwidth.
JPEG Quality: If you selected JPEG as an encoding option, you can select the quality of the video from this drop-down menu.
RTSP URL: This setting allows you to set a suffix for your camera’s RTSP URL, so you can view your camera’s video with this video
profile’s settings. For example, if you enter “mpeg4” as your RTSP URL setting and your camera’s IP is 192.160.0.30,
you can view your camera’s video with these settings through 192.160.0.20/mpeg4 .
Note: Video Profile 3 is always set to MJPEG as the Encode Type to ensure that at least one of the Video Profiles are
viewable by non-IE browsers. Video Profile 4 is for mobile devices only, and always uses MPEG-4 as the Encode Type.
Check to turn on the external speaker. You can use a microphone on your computer to talk through the speaker
Enable Speaker: connected to the camera.
Volume:
Change the volume of the external speaker.
Checking this box will enable you to listen to audio picked up by the camera’s microphone. This will allow you to hear
Enable Microphone: what is happening near your camera.
Volume:
This sets the volume level of the incoming audio.
Note: Higher frame size, frame rate and bit rates will give you better video quality, but they will also require more
network bandwidth. For best viewing results on a mobile phone, we suggest setting the frame rate to 5 fps and bit
rate to 20 Kbps.
After making any changes, click the Save Settings button to save your changes, or click the Don’t Save Settings
button to discard your changes.
Save Settings:
Click the Save Settings button to save and activate your settings.
D-Link DCS-5605/DCS-5635 User Manual
43
Motion Detection
Enable Motion Check the box to enable motion detection. This will allow the camera to serve as a security device by recording
Detection: only when motion is detected.
Sensitivity: Specify how much movement is required to trigger the motion detection. Refer to the next page to set up the trigger
area.
D-Link DCS-5605/DCS-5635 User Manual
44
Drawing Mode
Draw Motion Area: Select to draw a motion area.
Erase Motion Area: Select to use the mouse to remove motion areas.
Clear: Click the Clear button to remove all drawing areas.
Save Settings: Click the Save Settings button to save and activate your settings.
The red grid indicates an area that has been selected for motion detection. When motion is detected, the LIVE VIDEO page will display
a blinking orange motion video icon like the one below.
Note: The motion notification will continue to blink as long as
motion is detected. If no additional motion is detected, it will
return to its original state after eight seconds.
Motion
No Motion
D-Link DCS-5605/DCS-5635 User Manual
45
Motion Detection Setup Wizard
To run the Motion Detection Setup Wizard, log into the camera’s
web-based configuration and click the Setup tab.
Click the Motion Detection Setup Wizard button.
Click Next to continue.
D-Link DCS-5605/DCS-5635 User Manual
46
Click the Enable Video Motion box.
To draw an area, click the Draw Motion Area button and click
on the area on the screen where you want to detect motion. In
the example to the right, the red box is over a door. If there is
any motion in the door way, the camera will email a user and/
or record the activity.
To remove any of the area (red boxes), click the Erase Motion
Area and click the red boxes you want to remove.
To remove all motion areas, click the Clear button.
Click Next to continue.
E-mail Address: If you select the option, the current still image
is captured and an E-mail with the captured
image file attached is sent to the recipient
E-mail address.
User Name: This will be the username that was given
by your ISP (Internet Service Provider).
This could be smith or smith@yourisp.com
depending on your particular ISP.
Password: The password that you set up to view your
e-mail account.
SMTP Mail Server: The host name of the e-mail server (For
example smtpserver.yourdomain.com).
Sender E-mail The sender’s email address that appears
Address: in the email alert (For example smith@isp.
com). Notification will be sent to this email
address if the e-mails failed to be delivered
to the recipient email address.
D-Link DCS-5605/DCS-5635 User Manual
47
Recipient E-mail Address: This is the email address that will receive all the captured images.
Port: This is the port that your email SMTP service is running on. Default is 25.
FTP Server: Send a snapshot to FTP Server.
User Name: The account name to access the FTP server.
Password: The password that was setup with the account to access the FTP server.
Host Name: The host name or IP Address of the FTP server. (i.e. ftp.dlink.com)
Path: The directory that the images will be uploaded into (For example, \pub\images).
Filename Prefix: The prefix that will be added to the front of each filename.
Port: The port of the FTP server. Most FTP servers are running at the default port (21).
Interval: The time interval between each snapshot.
Passive Mode: Some FTP servers allow clients to use passive mode when connecting to an FTP, which uses random ports
for transfers.
D-Link DCS-5605/DCS-5635 User Manual
48
Once you are finished entering the requested information, click
Apply to finish the wizard.
D-Link DCS-5605/DCS-5635 User Manual
49
Time and Date
Time Zone: Select your time zone from the drop-down menu.
Enable Daylight Savings: Check to enable Daylight Savings. You can select Auto Daylight Time to automatically change or select
Set Date and Time Manually to enter the information.
Synchronize with NTP Server: Select to synchronize with a NTP time server on the Internet. Enter the NTP server URL or IP address,
or select a time server from the drop-down menu.
Set Day and Time Manually: Select to manually enter the date and time.
Copy your Computer’s Time Click to synchronize the time and date with the computer you are currently logged into the camera with.
settings:
D-Link DCS-5605/DCS-5635 User Manual
50
Preset Position
Set as Home: Click to set the current camera position as Home.
Default Home: Click to set Home to the default camera position.
Pan Speed: Change the pan speed from the drop-down (1-10, 10 = fastest).
Tilt Speed: Change the tilt speed from the drop-down (1-10, 10 = fastest).
Current Postion: Once you move the camera to a position you like, enter a name for the location and then click Add.
Patrol Selection: Allows you to add saved locations from the Preset Locations box into the Selected Locations box. This will determine
where the camera will travel to and stop at when you select Auto Patrol on the Live Video page.
Pan/Patrol Speed: The Pan/Patrol Speed control applies only when using the Pan and Patrol buttons in the live video interface.
Dwelling Time: Specify the number of seconds that the camera should remain fixed upon a specified preset position.
D-Link DCS-5605/DCS-5635 User Manual
51
Recording
Record to SD Card
Record to Samba Drive
Enable Recording: Check to enable the recording function.
SD Card: Select to record to an inserted Micro SD memory card.
D-Link DCS-5605/DCS-5635 User Manual
52
Samba Network Drive: Select to use Samba.
Samba Auth: Select the type of authentication from the drop-down menu.
User Name: Enter your Samba user name.
Password/Confirm: Enter your Samba password and again to confirm it.
Server: Enter the URL or IP address of the Samba drive.
Shared Folder: Enter the shared folder name.
Test: Click Test to verify your settings are correct.
Resolution: Select the profile from the drop-down menu. Refer to the Audio and Video section for more information on profiles.
Record until:
Enter the amount of space left on your hard drive before the camera stops recording. Must be at least 32MB.
Select Stop Recording to stop when you are out of hard drive space, specified in the Record until... option above;
When Storage is Full: or select Overwrite older recordings to have the camera continue recording but will overwrite old data.
Event Based:
Select the Motion detection triggered recording option to start recording when there is motion detected.
With the prerecord setting, the camera begin recording for a preset amount of time before motion was triggered is
Prerecord Seconds: recorded to the drive.
This setting enables the camera to record after a motion detection event has occurred. It records for a preset amount
Postrecord Seconds: of time after the event has been triggered, even though the motion may have ceased.
Scheduled:
Continuous:
Scheduled:
You can program recording to turn on and off at specific time each day.
Select this option to record video all the time (Samba only).
Select this option to record video based on the scheduled period of time (Samba only).
D-Link DCS-5605/DCS-5635 User Manual
53
Snapshot
D-Link DCS-5605/DCS-5635 User Manual
54
Snapshot
Enable Snapshot: When select the option, you can send a still image from this unit as an attachment of an E-mail or to an FTP server.
Select the Motion Detection option to transfers images to the specified FTP site or E-Mail address when there are
Trigger Event: motions detected. Select the D/I Signal 1 option to transfers images to the specified FTP site or E-Mail address
when Digital Input 1 is active.
Continuous (FTP Only):
Scheduled (FTP Only):
Select this option to record snapshots all the time.
Select this option to record snapshots based on the specified time period.
E-Mail Setting
If you select the option, the current still image is captured and an E-mail with the captured image file attached is
E-mail Address: sent to the recipient E-mail address.
This will be the username that was given by your ISP (Internet Service Provider). This could be smith or smith@
User Name: yourisp.com depending on your particular ISP.
Password:
SMTP Mail Server:
The password that you set up to view your e-mail account.
The host name of the e-mail server (for example, smtpserver.yourdomain.com).
The sender’s email address that appears in the email alert (for example, smith@isp.com). Notification will be sent
Sender E-mail Address: to this email address if the e-mails failed to be delivered to the recipient email address.
Recipient E-mail Address:
Port:
FTP Server:
User Name:
This is the email address that will receive all the captured images.
This is the port that your email SMTP service is running on. Default is 25.
FTP Setting
Send a snapshot to FTP Server.
The account name to access the FTP server.
The password that was setup with the account to access the FTP server.
D-Link DCS-5605/DCS-5635 User Manual
55
Password:
Host Name:
Path:
Filename Prefix:
Port:
Interval:
The host name or IP address of the FTP server. (i.e. ftp.dlink.com)
The directory that the images will be uploaded into (For example, \pub\images).
The prefix that will be added to the front of each filename.
The port of the FTP server. Most FTP servers are running at the default port (21).
The time interval between each snapshots.
Some FTP servers allow clients to use passive mode when connecting to an FTP, which uses random ports
Passive Mode: for transfers.
D-Link DCS-5605/DCS-5635 User Manual
56
SD Card
SD Status: The status of the Micro SD memory card will be
displayed.
Format SD Card: Click to format the Micro SD memory card. This
will delete all data on your card.
View Recorded Picture: If the picture files are stored on the SD card, click
on the picture folder and choose the picture file
you would like to view.
Playback Recorded Video: If video files are stored on the SD card, click on
the video folder and choose the video file you
would like to view.
Refresh: Reloads the file and folder information from the
SD card.
D-Link DCS-5605/DCS-5635 User Manual
57
Advanced
ICR
ICR: Click to triggers traditional alarming devices that connect to the system, such as alarm lights and sirens.
Automatic: The camera will automatically enable or disable ICR depending on the amount of light is detected.
Day Mode: Select if your camera is in a high-light area.
Night Mode: Select if your camera is in a low-light area and you need to improve the video quality.
Schedule Mode: Select to set a specific time range to enable Day mode. The camera will switch to Night mode when outside this
time range.
D-Link DCS-5605/DCS-5635 User Manual
58
Digital Output
The I/O connector on the camera provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting
such external alarm devices as IR-Sensors and alarm relays to the PTZ IP camera.
External I/O Port
I/O Connector Definition for the Camera
The DCS-5605/DCS-5635 provides a general I/O terminal block with one digital input and one relay switch for device control. Pin 1 and
pin 2 can be connected to an external sensor and the state of voltage will be monitored from the initial state ‘LOW’. The relay switch of
pin 3 and pin 4 can be used to turn on or off the external device.
The I/O connector provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting a diversity of
external alarm devices to the Camera such as IR-Sensors and alarm relays.
The digital input is used for connecting external alarm devices and once triggered images will be taken and e-mailed.
I/O Connector
1 DI+
2 DI-
3 SW_COMMON
4 SW_NOPEN D-Link DCS-5605/DCS-5635 User Manual
INPUT (Max. 50mA, 12VDC)
INPUT (Initial state of DI is low)
OUTPUT (open from SW_OPEN at initial state)
(close with SW_OPEN when set DO to ON)
OUTPUT (Max. 1A, 24VDC or 0.5A, 125VAC)
59
The above diagram shows a typical wiring configuration for a normally closed PIR motion sensor. Please refer to your specific motion sensor for the power supply connection to the device since this will be critical to the success of your installation. Note that the positive from
the PIR is connected to the D+ of the I/O port of the camera and the negative from the PIR is connected to the D- of the camera I/O port.
External Trigger Configuration
Configuring Your Camera for External Trigger-Based Recording
To configure your camera to record when triggered by an external device, you must first set your SMTP or FTP settings in order to send
snapshots to your email account or FTP server, or video to your Samba network drive or an inserted Micro SD memory card.
D-Link DCS-5605/DCS-5635 User Manual
60
To record video to your Samba network drive or an inserted Micro SD memory card, go to the Setup > Recording section. If you want to
record snapshots to your FTP server or sent to your email, skip to the next page.
Step 1 - Check the Enable Recording box.
Step 2 - Under Record to, select either SD Card or Samba Network Drive.
If you select Samba, entered the required information.
Step 3 - Under Recording Options, select the following options:
•Resolution - Select the video profile from the drop-down
menu.
•Record until xxx MB of free space - Enter the amount of
free space on the selected drive before either stop recording
or overwrite old recordings.
Step 4 - Under Recording Method, select Event Based and then select
Motion Detection Triggered Recording and/or Input 1 Triggered
Recording.
Step 5 - Enter the Prerecord and Postrecord time in seconds. For
example, if you enter 4 seconds for both, the camera will record
4 seconds before the trigger and then 4 seconds after the event
has ended.
Step 6 - Click Save Settings. Skip to page 55 to continue.
D-Link DCS-5605/DCS-5635 User Manual
61
To save snapshots to your FTP server or sent to your email, go to the Setup > Snapshot section. If you want to record video to your
Samba network drive or an inserted Micro SD memory card, refer to the previous page.
Step 1 - Check the Enable Snapshot box.
Step 2 - Under Scheduling, check Event Based. Select Motion Detection
and/or D/I Signal 1.
Step 3 - Select Continuous (FTP Only) to record snapshots all the time
or Scheduled (FTP Only) to record snapshots based on the
specified time period.
Step 4 - Under Send To, select either Email Address or FTP Server. Refer
to pages 48-49 for more information on the individual fields.
Step 5 - Click Save Settings.
D-Link DCS-5605/DCS-5635 User Manual
62
Click on Advanced and then click Digital Output on the left side.
Enable D/O Signal: Click to triggers traditional alarming devices that connect to the system, such as alarm lights and sirens.
Motion Detection: When a motion is detected, the camera will trigger traditional alarming devices that connect to the system.
D/I Signal 1: When triggering the digital input 1 device, the camera will trigger traditional alarming devices that connect to the
system.
D-Link DCS-5605/DCS-5635 User Manual
63
Maintenance
Admin
Change Password
Add/Delete User Accounts
Admin Password: Change the password for the admin account.
User Account: Create user accounts. Enter a user name and then a password for that user. Click the Add button to add the user
account.
User List: All accounts (except for the admin account) will be listed. To remove the user account, select from the drop-down
menu and click the Delete button.
D-Link DCS-5605/DCS-5635 User Manual
64
Device Settings
Change Camera Name
On-Screen Display
Turn On/Off LEDs
Calibrate Device
Camera Name: Enter a name for the camera. This is useful when multiple cameras are on your network.
Enable OSD: Check to enable the on-screen display (OSD). This will display the label and the time on the video.
Label: Enter a name (I.E. a location such as “front door” or “parking lot”) to be displayed on the video.
Show Time: Check the box to display the date and time on the video (time stamp).
LED Light: Select Off to turn off the LED lights on the camera. This is useful to hide the camera or give the illusion the camera
is turned off.
Calibrate the Device: Click the Calibrate the Device button to reset the home position to the default setting if the camera was moved by
hand or an external force.
D-Link DCS-5605/DCS-5635 User Manual
65
System
Save to Local Hard Drive: Click the Save Configuration button to save the camera settings to a file.
Load From Local Hard Drive: To load a configuration file, click the Browse button and navigate to a configuration file. Click the file and click
OK and then click the Load Configuration button to apply the settings to the camera.
Restore to Factory Defaults: Click the Restore Factory Defaults button to set the camera back to the factory default settings.
Reboot Device: Click the Reboot Device button to restart the camera.
D-Link DCS-5605/DCS-5635 User Manual
66
Firmware Upgrade
Your current firmware version and date will be displayed on your screen. You may go to the D-Link Support page to check for the latest
firmware version available.
Firmware Upgrade: To upgrade the firmware on your camera, please download and save the latest firmware version from the D-Link
Support page to your local hard drive. Locate the file on your local hard drive by clicking the Browse button. Then,
open the file and click the Upload button to start the firmware upgrade. Do NOT power the camera off during this
process.
D-Link DCS-5605/DCS-5635 User Manual
67
Status
Device Info
This page displays all the details information about your device and network connection.
D-Link DCS-5605/DCS-5635 User Manual
68
Log
This page displays the log information of your camera. You can save the log to a .txt file to your hard drive by clicking the Download button.
D-Link DCS-5605/DCS-5635 User Manual
69
Help
D-Link DCS-5605/DCS-5635 User Manual
70
Appendix
Frequently Asked Questions
1. What is an Internet Camera?
The Internet Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network. It differs from a conventional
PC Camera, the Internet Camera is an all-in-one system with built-in CPU and Web-based solutions providing a low cost solution that
can transmit high quality video images for monitoring. The Internet Camera can be managed remotely, accessed and controlled from
any PC/Notebook over an Intranet or the Internet from a Web browser.
2. What is the maximum number of users that can be allowed to access DCS-5605/5635 simultaneously?
The maximum number of users that can log onto the Internet Camera at the same time is 10. Please keep in mind the overall performance
of the transmission speed will slow down when many users are logged on.
3. What algorithm is used to compress the digital image?
The Internet Camera utilizes MPEG-4 Simple Profile Mode image compression technology to provide high quality images.
4. Can I capture still images from the Internet Camera?
Yes you are able to capture still images with the snapshot function from the software application CD supplied with the Internet Camera
or with the snapshot function on the Home page using an Internet browser.
5. Can the Internet Camera be used outdoors?
The Internet Camera is not weatherproof, and needs to be equipped with a weatherproof case in order to be used outdoors
(recommended).
6. When physically connecting the Internet Camera to a network what network cabling is required?
The Internet Camera uses Category 5 UTP cable allowing 10 Base-T and 100 Base-T networking.
7. Can the Internet Camera be setup as a PC-cam on a computer?
No, the DCS-5635 Internet Camera is used only on a wireless 802.11n/g, Ethernet, or Fast Ethernet network.
D-Link DCS-5605/DCS-5635 User Manual
71
8. Can the DCS-5605/5635 be connected to the network if it consists of only private IP addresses?
Yes, the Internet Camera can be connected to a LAN with private IP addresses.
9. Can the DCS-5605/5635 be installed and work if a firewall exists on the network?
If a firewall exists on the network, port 80 needs to be opened for ordinary data communication. The DCS-5605/5635 uses HTTP port
and RTSP port to stream video data. These ports (or the ports you specify from the Advanced Tab in the Configuration screen if you
change the default ports) need to be opened in the firewall device.
10. Why am I unable to access the DCS-5605/5635 from a Web browser?
If a router or firewall is used on the network, the correct ports for the DCS-5605/5635 may not be configured on the router or firewall.
To correct the problem, you need to determine if the DCS-5605/5635 is behind a router or firewall and if the router or firewall is
properly configured for the ports the DCS-5605/5635 is using.
Other possible problems might be due to the network cable. Try replacing your network cable. Test the network interface of the
product by connecting a local computer to the unit, utilizing a Ethernet crossover cable. If the problem is not solved the Internet
Camera might be faulty.
11. Why does the Internet Camera work locally but not externally?
This might be caused by network firewall protection. The firewall may need to have some settings changed in order for the Internet
Camera to be accessible outside your local LAN. Check with the Network Administrator for your network.
Make sure that the Internet Camera is not conflicting with any Web server you may have running on your network. The default router
setting might be a possible reason. Check that the configuration of the router settings allow the Internet Camera to be accessed
outside your local LAN.
D-Link DCS-5605/DCS-5635 User Manual
72
12. I connected the Internet Camera directly to a computer with a cross-over cable Ethernet cable and
received the following Windows error upon running the Installation Wizard:
This Windows error will occur if the Internet Camera is connected to a computer that is not properly configured
with a valid IP address. Turn off DHCP from the Network Settings in Windows® and configure the computer
with a valid IP address, or connect the camera to a router with DHCP enabled.
13. Why does a series of broad vertical white lines appear throughout the image?
It could be that the CMOS sensor has become overloaded when it has been exposed to bright lights such as direct exposure to
sunlight or halogen lights. Reposition the Internet Camera into a more shaded area immediately as prolonged exposure to bright
lights will damage the CMOS sensor.
14. Noisy images occur. How can I solve the problem?
The video images might be noisy if the Internet Camera is used in a very low light environment. To solve this issue you need more
lighting.
15. The images appear to be of poor quality, how can I improve the image quality?
Make sure that your computer’s display properties are set above 256 colors. Using 16 or 256 colors on your computer will produce
dithering artifacts in the image, making the image appear to be of poor quality.
The configuration on the Internet Camera image display is incorrect. Through the Image Setup section of the Web management you
need to adjust the image related parameters such as brightness, contrast, hue and power line frequency for fluorescent light. Please
refer to the Image Setup section for detailed information.
D-Link DCS-5605/DCS-5635 User Manual
73
How to Ping Your IP Address
The PING (Packet Internet Groper) command can determine whether a specific IP address is accessible by sending a packet to the specific
address and waiting for a reply. It can also provide a very useful tool to confirm if the IP address conflicts with Camera over the network.
Follow the step-by-step procedure below to utilize the PING command but first you must disconnect the Camera from the network.
Click on Start > Run and type in CMD
Type ping x.x.x.x, where x.x.x.x is the IP address of the Camera.
The replies, as illustrated below, will help diagnose any connection problems.
D-Link DCS-5605/DCS-5635 User Manual
74
Using & Configuring 3G Compatible Cell Phones
To enable mobile device video streaming, you will need to configure profile 4 for mobile viewing (see below).
D-Link DCS-5605/DCS-5635 User Manual
75
Play from RealPlayer
The following steps are based on a Nokia 6630 cell phone.
Step 1 - Press the Menu button and select Media.
Step 2 - Select Open.
Step 3 - Select RealPlayer.
D-Link DCS-5605/DCS-5635 User Manual
76
Step 4 - Select Open.
Step 5 - When RealPlayer opens, press Options.
D-Link DCS-5605/DCS-5635 User Manual
77
Step 6 - Select Download.
Step 7 - Select Video Clips. Note: 71.34.50.5 is the camera’s
IP address in this sample.
Step 8 - Press Options.
D-Link DCS-5605/DCS-5635 User Manual
78
Step 9 - Select Navigation Options.
Step 10 - Select Go to web address.
Step 11 - Input your rtsp address.
D-Link DCS-5605/DCS-5635 User Manual
79
Step 12 -Press Yes, and allow Connection and Loading
of the streaming video.
Step 13 - Enjoy streaming video on your cellphone.
D-Link DCS-5605/DCS-5635 User Manual
80
Play from PVPlayer
The following steps are based on a Nokia 6630 cell phone.
Step 1 - Press the Menu button and select PVPlayer.
Step 2 - Select Open.
Step 3 - Press the Options button.
D-Link DCS-5605/DCS-5635 User Manual
81
Step 4 - Select Open.
Step 5 - Input your rtsp address.
Note: 71.34.50.5 is the camera’s IP address in this
sample.
Step 6 - Enjoy streaming video on your cellphone.
D-Link DCS-5605/DCS-5635 User Manual
82
Reset and Restore
There is a button hidden in the pinhole beside the Ethernet socket. It is used to reset the system or restore the factory default settings.
Sometimes resetting the DCS-5605/DCS-5635 will return the system back to a normal state. If the system still has problems after reset,
restore the factory settings and install again:
RESET:
1. Lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera, press lightly and then release
the button.
2. The LED on the front of the camera will begin blinking red and green.
3. When the LED stops the blinking the reset has completed.
RESTORE:
1. Insert the paperclip or other tool and press on the button continuously.
2. Wait for the LED on the front of the camera to blink red and green and hold the button through two cycles of blinking
(about 5-7 seconds.)
3. Withdraw the tool after the second cycle of the LED blinking and a factory restore has been completed.
Restoring the factory defaults will result in the loss of any previous
settings and will require running the Installation Wizard to return the
DCS-5605/DCS-5635 to a normal state.
Reset Button
D-Link DCS-5605/DCS-5635 User Manual
83
Enabling UPnP™ for Windows® XP
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment,
software, and peripherals. The DCS-5605/DCS-5635 is a UPnP™ enabled Camera. If your operating system is UPnP™ enabled, the device
will be easier to configure. If you do not want to use the UPnP™ functionality, it can be disabled by unselecting “Enabled” on the DDNS/
UPnP™ settings page under Advanced in the configuration menu. Use the following steps to enable UPnP™ (Universal Plug and Play)
settings only if you are running Windows® XP.
Step 1 - Go to Start > Settings > Control Panel.
Step 2 - Click Add or Remove Programs
D-Link DCS-5605/DCS-5635 User Manual
84
Step 3 - Click Add/Remove Windows Components.
Step 4 - The following screen will appear. Click Add/Remove
Windows Components, highlight Networking Services,
and then click Details.
Step 5 - Check the Universal Plug and Play box and then click
OK.
D-Link DCS-5605/DCS-5635 User Manual
85
Step 6 - Click Next to continue.
Step 7 - Please wait while Setup configures the components.
Step 8 - Click Finish.
D-Link DCS-5605/DCS-5635 User Manual
86
Step 9 - To view your DCS-5605/DCS-5635 Camera in an
Internet browser, go to your Desktop and click My
Network Places.
Step 10 -The last three digits (146), represent the fourth
octet of your Camera’s IP address (in this example,
198.168.0.146).
Step 11 -After you click on the DCS-5605/DCS-5635-146
icon, your Internet browser will automatically be
opened to the IP address of the camera, in this
example it is: http://192.168.0.146. Your camera
may have a different IP Address.
D-Link DCS-5605/DCS-5635 User Manual
87
Technical Specifications
PACKAGE CONTENTS
• Internet Camera
• 12V/2A External Power Adapter
• CAT5 Ethernet cable
• Quick Install Guide
• Master CD
• A/V Cable
• Plate
• Mounting Screws
CAMERA SPECIFICATIONS
• Minimum Illumination:
Color: 0.7 Lux / F1.8
B/W: 0.02 Lux / F1.8
• Pan angle: +/- 165 degrees
• Tilt angle: -87 to +34 degrees
• Field of View (approximate)
Horizontal: 51° (Wide) to 6° (Tele)
Vertical: 40° (Wide) to 4° (Tele)
Diagonal: 63° (Wide) to 7° (Tele)
PROTOCOLS
• IPv4, ARP, TCP, UDP, ICMP, DHCP Client, NTP Client
(D-Link), DNS Client, DDNS Client (D-Link), SMTP Client,
FTP Client, HTTP Server, Samba Client, PPPoE, UpnP Port
Forwarding, RTP, RTSP, RTCP, 3GPP
LEDS
• Link/Power/WPS
WIRELESS*
• Security: WEP, WPA-PSK, WPA2
• Supports WPS
D-Link DCS-5605/DCS-5635 User Manual
RESOLUTION
• NTSC: 704 x 480 / 352x240 /176x120 : 30 fps
• PAL: 704 x 576 / 352x288 /176x144 : 25 fps
CODEC SUPPORT
• MPEG4/MJPEG/H.264 (simultaneous)
• JPEG for still image
INTERFACES
• LAN
• Microphone
• I/O
• Line/Video Out
• MicroSD
• WPS
• Reset
DATA RATES*
• IEEE 802.11n: From MCS0 to MCS15
• IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
• IEEE 802.11b: 11, 5.5,2, 1 Mbps
• Auto-select or Manual specified
POWER
• 12VDC/2A
POWER CONSUMPTION
• 100-240VAC, 50/60Hz, 0.4A
SYSTEM REQUIREMENTS
• Operating System: Windows® 7, Vista®, or XP
• Browser: Internet Explorer, Safari, Firefox, Mozilla or Opera
88
DIMENSIONS (L x W x H)
• 140.3 x 136.1 x 140.1 mm
WEIGHT
• DCS-5605: 810g
• DCS-5635: 855g
OPERATING TEMPERATURE
• 0° to 40° (32° to 104°)
STORAGE TEMPERATURE
• -20° to 70° (-4° to 158°)
OPERATING HUMIDITY
• 20%-80% RH non-condensing
CERTIFICATIONS
• FCC
• IC
• CE
• C-Tick
D-Link DCS-5605/DCS-5635 User Manual
89
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DCS-5605/DCS-5635)
• Hardware Revision (located on the label on the bottom of the Camera (e.g. rev A1))
• Serial Number (s/n number located on the label on the bottom of the Camera).
You can find software updates and user documentation on the D-Link website as well as frequently asked questions and answers to
technical issues.
For customers within the United States:
Phone Support:
(877) 354-6555
Internet Support:
http://support.dlink.com
For customers within Canada:
Phone Support:
(877) 354-6560
Internet Support:
http://support.dlink.ca
D-Link DCS-5605/DCS-5635 User Manual
90
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
•
•
Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military
Installations, or addresses with an APO or FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship and
materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except as otherwise stated herein.
•
•
•
Hardware (excluding power supplies and fans): One (1) year
Power supplies and fans: One (1) year
Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to repair or replace the
defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any repair or replacement will be rendered by
D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the
defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to
the defective Hardware. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and
is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective
Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware
or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty
Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the
Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. The customer’s sole and exclusive remedy and the
entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that
substantially conforms to D-Link’s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except
as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted
by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions.
If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price
paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned
to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover
any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly
disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any warranty whatsoever including, without limitation, the
Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the
product is within warranty, the customer shall submit a claim to D-Link as outlined below:
D-Link DCS-5605/DCS-5635 User Manual
91
•
The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow
D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.
•
The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving any suspected
defects with the product. If the product is considered defective, the customer must obtain a Return Material Authorization (“RMA”) number by completing the RMA
form and entering the assigned Case ID Number at https://rma.dlink.com/.
•
After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be
damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping
package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
•
The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by
D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain
Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the
customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States,
otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from
the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in
accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
What Is Not Covered: The Limited Warranty provided herein by D-Link does not cover: Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration,
modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the
product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping
costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due
to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been
purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to
the product. While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service
Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY
OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED
WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER
THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR
OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED
WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON,
D-Link DCS-5605/DCS-5635 User Manual
92
OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO
WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED
BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR
REMEDIES, EXPRESS, IMPLIED OR STATUTORY.
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This Limited Warranty provides specific legal rights
and you may also have other rights which vary from state to state.
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright
Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright © 2010 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate
measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office.
D-Link DCS-5605/DCS-5635 User Manual
93
Registration
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Version 1.0
February 22, 2010
D-Link DCS-5605/DCS-5635 User Manual
94
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising