FIREWORK MOVE

FIREWORK MOVE
FIREWORK MOVE
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
3. How To Set The Unit
4. How To Control The Unit
5. Troubleshooting
6. Fixture Cleaning
User Guide
Professional Entertainment Technology
1-
1. Safety Instruction
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt
WARNING
Please read carefully the instruction, which includes important information
any repairs yourself. In the unlikely event your unit may require service, please contact
about the installation, usage and maintenance.
your nearest dealer.
y Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the
y Unpack and check carefully there is no transportation damage before using the unit.
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
y Before operating, ensure that the voltage and frequency of power supply match the power
structure to which you are attaching the unit is secure and is able to support a weight of 10
requirements of the unit.
times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
y It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is
y The unit is for indoor use only. Use only in a dry location.
out of the touch of people and has no one pass by or under it.
y The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
y Disconnect main power before replacement or servicing.
y Make sure there is no flammable materials close to the unit while operating as it is fire
hazard.
2. Technical Specification
• 6 DMX Channels:
Channel 1 = Pan
y Use safety cable when fixes this unit.
Channel 2 = Tilt
y Maximum ambient temperature is Ta: 40℃. Don’t operate it where the temperature is
Channel 3 = Red
higher than this.
Channel 4 = Green
y In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
Channel 5 = Rotation
Channel 6 = Macro
malfunction. Please contact the nearest authorized technical assistance center. Always
• Voltage: 120V/230V~50/60Hz
use the same type spare parts.
• Fuse: 1A
y Do not touch any wire during operation as high voltage might be causing electric shock.
• Laser Power: Green 30mW+Red 80mW
• Power Consumption: 25W
Warning
• Dimension: 194 x 248 x 307 mm
y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
• Weight: 4.5 kg
moisture.
y Do not open the unit within five minutes after switching off.
y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
2-
3-
3. How To Set The Unit
DMX 512 Address Setting
3.1 Main Function
Press the MENU button up to when the
To select any of the given functions, press the MENU button up to when the required one is
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
showing on the display. Select the function by ENTER button and the display will blink. Use
Once the address has been selected, press the ENTER button to setup or automatically
DOWN and UP button to change the mode. Once the required mode has been selected,
return to the main functions without any change after 8 seconds. To go back to the functions
press the ENTER button to setup or it will automatically return to the main functions without
without any change press the MENU button again.
is showing on the display. Pressing ENTER
any change after idling 8 seconds. To go back to the functions without any change press the
Show Mode
MENU button. The main functions are showing below:
is showing on the display. Pressing ENTER
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to select the
(show 2) or
or
(show 3) or
(show 1)
(show 4) mode. Once the mode has
been selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
to the audience’s direction; i.e in front of the stage. Pan movement angel (left to right to
left): 160°. Tilt movement angel: 90° (60° above horizon; 30° below horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angel (left to right to left):160°. Tilt movement angel:
90° (vertically, front 75°; back 15°)
Slave Mode
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(2 light show) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Sound Mode
Press the MENU button until the
4-
is showing on the display. Pressing ENTER button
5-
and the display will blink. Use DOWN and UP button to select the
(sound on) or
Display Inversion
(sound off) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
go back to the functions without any change press the MENU button again.
when the
is blinking on the display. Use the ENTER button to change to the mode
(display normal), It will automatically store after 8 seconds. Or press the ENTER
Blackout Mode
button again return to the mode
is showing on the display. Pressing
Press the MENU button up to when the
(display inversion). To go back to the functions
press the MENU button.
ENTER button and the display will blink. Use DOWN and UP button to select the
Display normal mode for the fixture putting on the floor.
(yes blackout) or
Display inversion mode for the fixture fixing under ceiling.
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Self-Test
is blinking on the display. Pressing ENTER
Press the MENU button up to when the
button and the unit will run self-test by built-in program. To go back to the functions press the
Pan Inversion
MENU button again.
is showing on the display. Pressing ENTER
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to select the
or
(normal)
(pan inversion) mode. Once the mode has been selected, press the ENTER
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button to setup or automatically return to the main functions without any change after 8
button and the display will show the number of working hours of the unit. To go back to the
seconds. To go back to the functions without any change press the MENU button again.
functions press the MENU button again.
Software version
Tilt Inversion
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
or
(normal)
(tilt inversion) mode. Once the mode has been selected, press the ENTER
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the version of software of the unit. To go back to the
functions press the MENU button again.
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Reset
is blinking on the display. Pressing ENTER
Press the MENU button up to when the
Led Display
button and all channels of the unit will return to their standard position. To go back to the
Press the MENU button up to when the
is showing on the display. Pressing
functions without any change press the MENU button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
4. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
6-
7-
3. By universal DMX controller
following diagram to address your DMX512 channel for the first 4 units.
No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show
on the
display and move all the motors to their ‘home’ position. After that the unit will be ready to
receive DMX signal or run the built in programs.
4.4 DMX 512 Configuration
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when you
want an instant show.
2-light show
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
4.2 Easy Controller
The easy remote control is used only in master/slave mode. By connecting CA-8 to the 1/4”
microphone jack of the first unit, you will find that the remote control on the first unit will
control all the other units functions press the MENU button again.
Stand By
Blackout the unit
Function
1. Strobe Red
2. Strobe Green
Show
Rotation
1-4
Speed
LED Blinking
LED ON
3. Strobe in Green/Red
Mode
Sound (LED OFF)
4.3 DMX Controller
Use universal DMX controller to control the units, you have to set DMX address from 1 to
512 so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
8-
9-
4.5 DMX512 Connection
5. Troubleshooting
The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
1.
If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
cause damage or interference to DMX interface circuit.
adapter-cable.
2.
At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
4.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
in the DMX-output of the last unit.
3.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
1. Make sure the unit does not receive DMX signal.
connectors can easily distort the signal and shut down the system.
2. Check microphone to see if it is good by tapping the microphone
The DMX output and input connectors are pass-through to maintain the DMX circuit,
E. One of the channels is not working well
when one of the units’ power is disconnected.
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
5.
Each lighting unit needs to have an address set to receive the data sent by the
2. The motor’s drive IC on the PCB might be out of condition
6.
The end of the DMX 512 system should be terminated to reduce signal errors.
7.
3 pin XLR connectors are more popular than 5 pin XLR.
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
Pin:Not Used.
10-
11-
6. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
y Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
Innovation, Quality, Performance
12-
13-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement