Alliance Laundry Systems | UniLinc | Specifications | Alliance Laundry Systems UniLinc Specifications

Alliance Laundry Systems UniLinc Specifications
Pocket Hardmount
UniLinc and M30 Control
Refer to Page 8 for Model Numbers
PHM798N
PHM798N
UniLinc 35 – 125 Models
PHM1422C
UniLinc 150 Model
PHM1422C
PHM802N
PHM802N
M30 35 – 125 Models
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. F8138601R11
June 2011
Installation
Washer-Extractors
Table of
Contents
Safety Information.............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
Safe Operating Environment ................................................................
Environmental Conditions ...............................................................
Machine Location ............................................................................
Input and Output Services................................................................
AC Inverter Drive ............................................................................
2
2
2
4
5
6
6
6
7
7
Introduction.........................................................................................
Model Identification .............................................................................
Delivery Inspection...............................................................................
Name plate Location.............................................................................
Nameplate Location - UniLinc Models ...........................................
Replacement Parts ................................................................................
Customer Service..................................................................................
8
8
9
9
9
9
9
Specifications and Dimensions...........................................................
Machine Dimensions ............................................................................
UWTV Models Through 3/31/09 ....................................................
UW Design 1 and Design 2 Models
Starting 4/1/09 Through 10/3/10 ...................................................
UW Design 3 Models starting 10/4/10 ...........................................
Machine Foundation Requirements......................................................
Concrete Foundation Pad Installation...................................................
Floor Load Data ...............................................................................
Mounting Bolt Installation Requirements ............................................
Machine Mounting and Grouting.....................................................
Mounting Bolt Hole Locations .............................................................
Grout Placement ...................................................................................
Gap Setting for Vibration Switch ....................................................
Drain Connection Requirements...........................................................
Water Connection .................................................................................
Electrical Installation Requirements.....................................................
Steam Requirements (Steam Heat Option Only)..................................
Chemical Injection Supply System.......................................................
External Supplies ..................................................................................
Chemical Injection Using Internal 24VAC Control Transformer ...
Chemical injection Using External AC Power Source ....................
External Supply Signals ...................................................................
11
15
15
18
21
24
25
27
30
31
32
37
38
42
44
46
51
52
55
56
57
58
© Copyright 2011, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Safety Information
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
F8138601
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
29. Do not attempt to open the door until the washer
has drained and all moving parts have stopped.
30. Do not climb onto or into the machine.
31. Be aware that hazardous chemicals may be
present.
32. Be aware that hot water is used to flush the
supply dispenser.
33. Wear hand and eye protection when adding
detergents and chemicals.
34. Avoid opening the dispenser lid while the
machine is running.
35. Do not attach anything to the supply dispenser’s
nozzles. The air gap must be maintained.
36. Use only low-sudsing, no-foaming types of
commercial detergent.
37. Do not operate the machine without the water
reuse plug or water reuse system in place.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance are
provided. Never allow the inspection and
maintenance space to be blocked.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Safety Information
Operator Safety
Do not bypass any safety devices in the machine.
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Safety Information
Safe Operating Environment
Safe operation requires an appropriate operating
environment for both the operator and the machine. If
questions regarding safety arise, contact the
manufacturer immediately.
Environmental Conditions
 Ambient Temperature. Water in the machine will
freeze at temperatures of 32°F (0°C) or below.
Temperatures above 104°F (40°C) will result in
more frequent motor overheating and, in some
cases, malfunction or premature damage to solid
state devices that are used in some models.
Special cooling devices may be necessary.
Water pressure switches are affected by increases
and decreases in temperature. Every 25°F (10°C)
change in temperature will have a 1% effect on
the water level.
 Humidity. Relative humidity above 90% may
cause the machine’s electronics or motors to
malfunction or may trip the ground fault
interrupter. Corrosion problems may occur on
some metal components in the machine.
If the relative humidity is below 30%, belts and
rubber hoses may eventually develop dry rot.
This condition can result in hose leaks, which
may cause safety hazards external to the machine
in conjunction with adjacent electrical
equipment.
 Ventilation. The need for make-up air openings
for such laundry room accessories as dryers,
ironers, water heaters, etc., must be evaluated
periodically. Louvers, screens, or other
separating devices may reduce the available air
opening significantly.
DANGER
Do not place volatile or flammable fluids
in any machine. Do not clean the machine
with volatile or flammable fluids such as
acetone, lacquer thinners, enamel
reducers, carbon tetrachloride, gasoline,
benzene, naptha, etc. Doing so could
result in serious personal injury and/or
damage to the machine.
SW002
 Water Damage. Do not spray the machine with
water. Short circuiting and serious damage may
result. Repair immediately all seepage due to
worn or damaged gaskets, etc.
Machine Location
 Foundation. The concrete floor must be of
sufficient strength and thickness to handle the
floor loads generated by the high extract speeds
of the machine.
 Service/Maintenance Space. Provide sufficient
space to allow comfortable performance of
service procedures and routine preventive
maintenance.
Consult installation instructions for specific details.
CAUTION
Replace all panels that are removed to
perform service and maintenance
procedures. Do not operate the machine
with missing guards or with broken or
missing parts. Do not bypass any safety
devices.
SW019
 Radio Frequency Emissions. A filter is available
for machines in installations where floor space is
shared with equipment sensitive to radio
frequency emissions.
 Elevation. If the machine is to be operated at
elevations of over 3280 feet (1000 m) above sea
level, pay special attention to water levels and
electronic settings (particularly temperature) or
desired results may not be achieved.
 Chemicals. Keep stainless steel surfaces free of
chemical residues.
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Safety Information
Input and Output Services
AC Inverter Drive
 Water Pressure. Best performance will be
realized if water is provided at a pressure of 30 –
85 psi (2.0 – 5.7 bar). Although the machine will
function properly at lower pressure, increased fill
times will occur. Water pressure higher than 100
psi (6.7 bar) may result in damage to machine
plumbing. Component failure(s) and personal
injury could result.
 Steam Heat (Optional) Pressure. Best
performance will be realized if steam is provided
at a pressure of 30 – 80 psi (2.0 – 5.4 bar). Steam
pressure higher than 125 psi (8.5 bar) may result
in damage to steam components and may cause
personal injury.
For machines equipped with optional steam heat,
install piping in accordance with approved
commercial steam practices. Failure to install the
supplied steam filter may void the warranty.
 Drainage System. Provide drain lines or troughs
large enough to accommodate the total number of
gallons that could be released if all machines on
the site drained at the same time from the highest
attainable level. If troughs are used, they should
be covered to support light foot traffic.
 Power. For personal safety and for proper
operation, the machine must be grounded in
accordance with state and local codes. The
ground connection must be to a proven earth
ground, not to conduit or water pipes. Do not use
fuses. An easy-access cutoff switch should also
be provided.
Machines equipped with the AC inverter drive require
special attention with regard to the operating
environment.
 An especially dusty or linty environment will
require more frequent cleaning of the AC inverter
drive cooling fan filter and of the AC inverter
drive itself.
 Power line fluctuations from sources such as
uninterruptible power supplies (UPS) can
adversely affect machines equipped with the AC
inverter drive. Proper suppression devices should
be utilized on the incoming power to the machine
to avoid problems.
 A clean power supply free from voltage spikes
and surges is absolutely essential for machines
equipped with the AC inverter drive. Nonlinear
inconsistencies (peaks and valleys) in the power
supply can cause the AC inverter drive to
generate nuisance errors.
 The following conditions must be corrected:
input voltage above 240V or 480V, phase to
ground voltage exceeds 125% of normal line to
line voltage, or 240V open delta configuration
(stinger leg). Contact the distributor or the
manufacturer for assistance.
 Sufficient space to perform service procedures
and routine preventive maintenance is especially
important for machines equipped with the AC
inverter drive.
WARNING
Ensure that a ground wire from a proven
earth ground is connected to the ground
lug near the input power block on this
machine. Without proper grounding,
personal injury from electric shock could
occur and machine malfunctions may be
evident.
SW008
Always disconnect power and water supplies before a
service technician performs any service procedure.
Where applicable, steam and/or compressed air
supplies should also be disconnected before service is
performed.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Introduction
Model Identification
Information in this manual is applicable to these
models:
8
UW35TV
UWL060K1L
UWN035K1L
UWN100K1M
UWU060K1L
UW60TV
UWL060K1M
UWN035K1M
UWN100T3V
UWU060K1M
UW80TV
UWL060T3L
UWN035T3L
UWN125K1M
UWU060T3L
UW100TV
UWL060T3M
UWN035T3M
UWN125K1V
UWU060T3M
UW125TV
UWL060T3V
UWN035T3V
UWN125T3V
UWU060T3V
UW150TV
UWL080K1M
UWN060K12
UWN150T3V
UWU080K1M
UWL035K12
UWL080T3V
UWN060K1L
UWU035K12
UWU080T3V
UWL035K1L
UWL100K1M
UWN060K1M
UWU035K1L
UWU100K1M
UWL035K1M
UWL100T3V
UWN060T3L
UWU035K1M
UWU100T3V
UWL035T3L
UWL125K1M
UWN060T3M
UWU035T3L
UWU125K1M
UWL035T3M
UWL125T3V
UWN060T3V
UWU035T3M
UWU125T3V
UWL035T3V
UWL150T3V
UWN080K1M
UWU035T3V
UWU150T3V
UWL060K12
UWN035K12
UWN080T3V
UWU060K12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Introduction
This manual is designed as a guide to the installation
of the Pocket Hardmount washer-extractor.
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
5. Press the
keypad.
Always provide the machine’s serial number and
model number when ordering parts or when seeking
technical assistance. Refer to Figure 1.
MODEL EXAMPLE OF NAMEPLATE LOCATION
1
IMPORTANT: Warranty is void unless washerextractor is installed according to instructions in
this manual. Installation should comply with
minimum specifications and requirements, and
with applicable municipal building codes, water
supply regulations, electrical wiring regulations
and any other relevant statuary regulations. Due to
varied requirements, applicable local codes should
be thoroughly understood and all pre-installation
work arranged for accordingly.
2
Delivery Inspection
Upon delivery, visually inspect crate, protective cover,
and unit for any visible shipping damage. If the crate,
protective cover, or unit is damaged or signs of
possible damage are evident, have the carrier note the
condition on the shipping papers before the shipping
receipt is signed, or advise the carrier of the condition
as soon as it is discovered.
Remove the crate and protective cover as soon after
delivery as possible. If any damage is discovered upon
removal of the crate and/or protective cover, advise the
carrier and file a written claim immediately.
Name plate Location
The nameplate is located on the back of the machine.
Always provide the machine’s serial number and
model number when ordering parts or when seeking
technical assistance. Refer to Figure 1 and Figure 2.
Nameplate Location - UniLinc Models
On UniLinc models, nameplate information is also
programmed into the control. To access machine ID
through the control:
1. Press and hold
, then
keypads at the same time.
, then
2. Press the
highlighted.
keypad until Diagnostic is
3. Press the
keypad.
4. Press the
highlighted.
keypad until machine ID is
F8138601
PHM798N
1
2
In Control (UniLinc Models)
At Back of Machine
Figure 1
Replacement Parts
If literature or replacement parts are required, contact
the source from which the washer-extractor was
purchased or contact Alliance Laundry Systems LLC
at (920) 748-3950 for the name of the nearest
authorized parts distributor. A parts manual may be
ordered by returning the reply card provided with each
washer-extractor.
Customer Service
For technical assistance, contact your local distributor
or call:
(920) 748-3121
Ripon, Wisconsin
A record of each washer-extractor is on file with the
manufacturer. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance. Refer to Figure 1
and Figure 2.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Introduction
Model Number Familiarization Guide - Models Through 3/31/09
Sample Model Number: UW60TVQU10001
UW
Model Number Prefix
60
Washer-Extractor Capacity (60 pounds dry weight of laundry)
T
Type of Electrical Control
T = UniLinc Control
V
Washer-Extractor Speed Capabilities
V = 8 Speeds
Q
Electrical Characteristics
Refer to Table 10.
U1
Design Series
0001
Option Identification (varies from machine to machine)
Model Number Familiarization Guide - Models Starting 4/1/09
Sample Model Number: UWN060T3VXU1001
UW
N
060
Model Number Prefix
Market Approvals
Washer-Extractor Capacity (60 pounds dry weight of laundry)
T
Type of Electrical Control
T = UniLinc Control
3
Spray/Dispenser Feature
V
Washer-Extractor Speed Capabilities
V = 8 Speeds
X
Electrical Characteristics
Refer to Table 10.
U1
Design Series
0
Heat Feature
01
Option Identification (varies from machine to machine)
Model No.
Serial No.
UWN060T3VXU1001
00000000000
200 – 240
Hz 50-60
Number of wires : 3
FLA : 19
Circuit Breaker Size : 30 amps
Max. Load : 60
LB
27 KG
Voltage
Schematic :
Supply Water:
30 - 85 psi, 2 - 5.7
Phase
3
amps
BAR
EXAMPLE OF SERIAL PLATE
PHM769N
PHM769N
Figure 2
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
.
UWTV Models Through 3/31/09
Specifications
35
60
80
100
125
150
Overall width, in (mm)
32.5 (826)
36.625 (930)
41.5 (1054)
41.5 (1054)
48 (1219)
50.25 (1277)
Overall height, in (mm)
55.5 (1410)
64.5 (1638)
68.5 (1740)
68.5 (1740)
72 (1829)
79 (2007)
Overall depth, in (mm)
43.625 (1108)
45 (1143)
51.5 (1308)
54.5 (1384)
58 (1473)
63 (1600)
1030 (468)
1300 (590)
1730 (785)
1770 (805)
2420 (1100)
2970 (1347)
150 (68)
200 (92)
330 (150)
360 (163)
550 (250)
572 (260)*
1085 (493)
1340 (608)
1795 (814)
1835 (832)
2525 (1148)
3022 (1371)
66 (1.9)
84 (2.4)
119 (3.4)
119 (3.4)
166 (4.7)
172 (4.87)
Domestic shipping dimensions,
WxDxH, in (mm)
38x47x64
(970x1200x
1630)
40x49x74.5
(1016x1245x
1892)
44x60.5 x77.25
(1118x1537x
1962)
44x60.5x77.25
(1118x1537x
1962)
61.5x60x77.75
(1560x1520x
1980)
54.5x69x79
(139x176x
201)
Export shipping weight, lb (kg)
1150 (522)
1464 (664)
1990 (903)
2030 (921)
2800 (1270)
3350 (1520)
78 (2.2)
96 (2.7)
134 (3.8)
134 (3.8)
184 (5.3)
220 (6.3)
41x50x65.5
(1050x1280x
1670)
43x52.125x74.5
(1092x1324x
1892)
47x63.5x77.25
(1194x1613x
1962)
47x63.5x77.25
(1194x1613x
1962)
63.5x63x80
(1620x1610x
2030)
61.5x71x87
(1562x1804x
2210)
Cylinder diameter, in (mm)
26.25 (667)
32 (813)
36 (914)
36 (914)
42 (1067)
43 (1093)
Cylinder depth, in (mm)
18.375 (467)
20 (508)
21 (533)
27 (686)
24 (610)
27.8125 (706)
Cylinder volume, ft3 (l)
5.76 (163)
9.31 (264)
12.4 (350)
15.9 (450)
19.2 (544)
23.4 (662)
Perforation size, in (mm)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
Perforation open area, %
18
22
23
23
24
21.5
Door opening size, in (mm)
14.375 (365)
17.5 (445)
17.5 (445)
17.5 (445)
20 (508)
24.75 (629)
Height of door bottom above floor,
in (mm)
23.75 (603)
28.25 (718)
29 (737)
29 (737)
29 (737)
32 (813)
1
1
1
1
1
1
5.0 (3.7)
5.0 (3.7)
7.5 (5.6)
7.5 (5.6)
10 (7.5)
10 (7.5)
Overall Dimensions
Weight And Shipping Information
Net weight, lb (kg)
Basket Weight, lb (kg)
Domestic shipping weight, lb (kg)
Domestic shipping volume,
ft3 (m3)
3
3
Export shipping volume, ft (m )
Export shipping dimensions,
WxDxH, in (mm)
Wash Cylinder Information
Door Opening Information
Drive Train Information
Number of motors in drive train
Drive motor power, hp (kW)
* Basket Only
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Specifications and Dimensions
UWTV Models Through 3/31/09 (Continued)
Specifications
35
60
80
100
125
150
Cylinder Speeds / Centrifugal Force Data
1/2 Wash/reverse, rpm (g)
26 (.25)
26 (.31)
26 (.35)
26 (.35)
26 (.40)
23 (.31)
Wash/reverse, rpm (g)
42 (.66)
40 (.73)
40 (.82)
40 (.82)
37 (.82)
36 (0.8)
Distribution, rpm (g)
83 (2.57)
71 (2.29)
73 (2.57)
70 (2.50)
62 (2.29)
61 (2.29)
Very Low extract, rpm (g)
401 (60)
364 (60)
343 (60)
343 (60)
317 (60)
314 (60)
Low extract rpm (g)
568 (120)
514 (120)
485 (120)
485 (120)
449 (120)
444 (120)
Medium extract, rpm (g)
695 (180)
630 (180)
594 (180)
594 (180)
550 (180)
543 (180)
High extract, rpm (g)
803 (240)
727 (240)
686 (240)
686 (240)
565 (190)
627 (240)
Very High extract, rpm (g)
898 (300)
813 (300)
766 (300)
766 (300)
579 (200)
701 (300)
STD
STD
STD
STD
STD
STD
0.5 (13)
0.5 (13)
0.5 (13)
0.5 (13)
0.75 (19)
0.75 (19)
1
1
1
1
1
1
LOW
2.1 (1.5)
3.3 (2.4)
4.6 (3.3)
5.7 (4.1)
6.7 (4.9)
8.3 (6.0)
MED
2.3 (1.7)
3.7 (2.6)
5.2 (3.8)
6.5 (4.7)
7.8 (5.6)
9.5 (6.9)
HIGH
2.7 (1.9)
4.1 (2.9)
6.1 (4.4)
7.6 (5.5)
9.1 (6.6)
11.1 (8.0)
1.4 (21.4)
2.1 (33.4)
3.1 (48.4)
3.8 (60.4)
4.6 (72.0)
5.8 (91.0)
15.6
27.4
41.2 (Q-Volt)
27.4 (N-Volt)
41.2 (Q-Volt)
27.4 (N-Volt)
N/A
N/A
6
6
9
9
N/A
N/A
2.6
4.2
4.2
4.2
N/A
N/A
LOW
2.4 (3.6)
2.4 (3.7)
2.2 (3.4)
2.8 (4.2)
N/A
N/A
MED
2.7 (4.1)
2.7 (4.1)
2.5 (3.9)
3.2 (4.8)
N/A
N/A
HIGH
3.1 (4.7)
3.0 (4.6)
3.0 (4.5)
3.7 (5.6)
N/A
N/A
Balance Detection
Vibration switch installed
Direct Steam Heating (Optional)
Steam inlet connection size,
in (mm)
Number of steam inlets
Steam required to
raise bath temperature
10°F, lb (10°C, kg)
Average consumption per
cycle, BHP (kg)
Electrical Heating (Optional)
Total electrical heating
capacity, kW
Number of electrical heating
elements
Electrical heating element size,
kW
Time required to
raise bath temperature
10°F, min (5°C, min)
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
UWL, UWN and UWU Models Starting 4/1/09
Specifications
35
60
80
100
125
150
Overall Dimensions
Overall width, in. (mm)
32.37 (822)
36.07 (916)
41.06 (1043)
41.06 (1043)
47.91 (1217)
50.23 (1256)
Overall height, in. (mm)
54.45 (1383)
64.5 (1638)
67.88 (1724)
67.88 (1724)
72.31 (1837)
78.9 (2004)
Overall depth, in. (mm)
44.49 (1130)
47.24 (1200)
49.88 (1267)
55.85 (1419)
56.54 (1436)
62.43 (1586)
Weight And Shipping Information
Net weight, lb. (kg)
925 (420)
1270 (576)
1750 (793)
1800 (816)
2190 (993)
2890 (1311)
Basket Weight, lb. (kg)
147 (67)
200 (92)
330 (150)
360 (163)
550 (250)
572 (260)*
Domestic shipping weight,
lb. (kg)
944 (428)
1302 (591)
1814 (823)
1870 (848)
2292 (1040)
2944 (1335)
Domestic shipping volume,
ft3 (m3)
61.5 (1.7)
83.25 (2.3)
111 (3.2)
111 (3.2)
135 (3.89)
171.5 (4.94)
Domestic shipping
dimensions, WxDxH,
in. (mm)
37.5x48x59
(952x1219x1498)
41.5x50.25x69
44x60x72.75
44x60x72.75
50.5x60x77
54.5x69x78.75
(1054x1276x1753) (1118x1524x1848) (1118x1524x1848) (1283x1524x1956) (1385x1753x2000)
Export shipping weight,
lb. (kg)
1050 (476.27)
1430 (648.63)
2010 (911.72)
2060 (934.40)
2570 (1165.73)
3270 (1483.24)
Export shipping volume,
ft3 (m3)
79.5 (2.27)
99.25 (2.83)
152.5 (4.35)
152.5 (4.35)
173 (4.93)
215 (6.13)
Export shipping dimensions,
WxDxH, in. (mm)
42x51x64
46x53.25x70
48.5x63x86.25
48.5x63x86.25
55x63x86.25
59x72x87.5
(1067x1295x1626) (1168x1353x1778) (1232x1600x2191) (1232x1600x2191) (1397x1600x2191) (1499x1829x2223)
Wash Cylinder Information
Cylinder diameter, in. (mm)
26.25 (667)
32 (813)
36 (914)
36 (914)
42 (1067)
43 (1093)
Cylinder depth, in. (mm)
18.375 (467)
20 (508)
21 (533)
27 (686)
24 (610)
27.8125 (706)
5.76 (163)
9.31 (264)
12.4 (350)
15.9 (450)
19.2 (544)
23.4 (662)
Perforation size, in. (mm)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
Perforation open area, %
18
22
23
23
24
21.5
Door opening size, in. (mm)
14.375 (365)
17.5 (445)
17.5 (445)
17.5 (445)
20 (508)
24.75 (629)
Height of door bottom above
floor, in. (mm)
23.48 (596)
28.07 (713)
29.46 (748)
29.46 (748)
28.5 (724)
31.41 (798)
Number of motors in. drive
train
1
1
1
1
1
1
Drive motor power, hp (kW)
2.0 (1.3)
(2-speed models)
5.0 (3.7)
(Variable-speed
models)
3.0 (2.2)
(2-speed models)
5.0 (3.7)
(Variable-speed
models)
7.5 (5.6)
7.5 (5.6)
10 (7.5)
10 (7.5)
Cylinder volume,
ft3
(l)
Door Opening Information
Drive Train Information
* Basket Only
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Specifications and Dimensions
UWL, UWN and UWU Models Starting 4/1/09 (Continued)
Specifications
35
60
80
100
125
150
Cylinder Speeds / Centrifugal Force Data
1/2 Wash/reverse, rpm (g)
(Variable-speed models only)
26 (.25)
26 (.31)
26 (.35)
26 (.35)
26 (.40)
23 (.32)
Wash/reverse, rpm (g)
44 (.73)
42 (.66)
40 (0.8)
40 (0.8)
37 (0.8)
36 (0.8)
Distribution, rpm (g)
(Variable-speed models only)
83 (2.57)
74 (2)
70 (2.50)
70 (2.50)
62 (2.29)
61 (2.29)
Very Low extract, rpm (g)
(Variable-speed models only)
401 (60)
364 (60)
343 (60)
343 (60)
317 (60)
314 (60)
Low extract rpm (g)
(Variable-speed models only)
568 (120)
514 (120)
485 (120)
485 (120)
449 (120)
444 (120)
Medium extract, rpm (g)
(Variable-speed models only)
695 (180)
630 (180)
594 (180)
594 (180)
550 (180)
543 (180)
803 (240)
(Variable-speed
models)
492 (90)
(2-speed models)
727 (240)
(Variable-speed
models)
482 (106)
(2-speed models)
686 (240)
686 (240)
565 (190)
627 (240)
898 (300)
813 (300)
766 (300)
766 (300)
579 (200)
701 (300)
STD (Variablespeed models)
N/A (2-speed
models)
STD (Variablespeed models)
N/A (2-speed
models)
STD
STD
STD
STD
0.5 (13)
0.5 (13)
0.5 (13)
0.5 (13)
0.75 (19)
0.75 (19)
1
1
1
1
1
1
LOW
2.1 (1.5)
3.3 (2.4)
4.6 (3.3)
5.7 (4.1)
6.7 (4.9)
8.3 (6.0)
MED
2.3 (1.7)
3.7 (2.6)
5.2 (3.8)
6.5 (4.7)
7.8 (5.6)
9.5 (6.9)
HIGH
2.7 (1.9)
4.1 (2.9)
6.1 (4.4)
7.6 (5.5)
9.1 (6.6)
11.1 (8.0)
1.4 (21.4)
2.1 (33.4)
3.1 (48.4)
3.8 (60.4)
4.6 (72.0)
5.8 (91.0)
High extract, rpm (g)
Very High extract, rpm (g)
(Variable-speed models only)
Balance Detection
Vibration switch installed
Direct Steam Heating (Optional)
Steam inlet connection size,
in. (mm)
Number of steam inlets
Steam required to
raise bath temperature
10°F, lb. (10°C, kg)
Average consumption per
cycle, BHP (kg)
Electrical Heating (Optional)
Total
electrical heating
capacity,
kW (N/A for 2 speed
models)
200V
10.8
19.1
28.6
28.6
N/A
N/A
240V
15.6
27.4
41.2
41.2
N/A
N/A
380V
9.8
17.2
17.2
17.2
34.4
N/A
415V
11.7
20.5
20.5
20.5
41.0
N/A
480V
15.6
27.4
27.4
27.4
54.8
N/A
6
6
9
9
12
N/A
2.6
4.2
4.2
4.2
4.2
N/A
Number of electrical heating
elements
Electrical heating element size,
kW
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Machine Dimensions
Dimensional Clearances
Allow a minimum of 24 inches (60 cm) at the rear and
6 inches (15.24 cm) at the sides for maintenance,
inspection, and adjustment. Allow at least 6 inches
(15.24 cm) between machines in multiple installations.
NOTE: The dimensions shown here are for
planning purposes only. They are approximate and
subject to normal manufacturing tolerances. If
exact dimensions are required for construction
purposes, contact the distributor or the
manufacturer. We reserve the right to make
changes at any time without notice.
WARNING
Crush hazard.
To avoid personal injury and/or property
damage, do not tip the UW150 machine
more than 25 degrees in any direction.
W642
UWTV Models Through 3/31/09
(Refer to Figure 3 and Figure 4)
Dimension
35
60
80
100
125
150
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
A
30.125
765
35.625
905
41.125
1045
41.125
1045
48
1219
50.25
1277
B1
33.375
848
36.625
930
41.5
1054
41.5
1054
48
1219
50.25
1277
C
23.75
603
28.25
718
29
737
29
737
29
737
32
813
D
43.625
1108
45
1143
51.5
1308
54.5
1384
58
1473
63
1600
E2
.5
13
1
25
3
76
3
76
1.5
38
2.9
73
F
55.5
1410
64.5
1638
68.5
1740
68.5
1740
72
1829
79
2007
G2
36
914
36
914
43.75
1111
43.75
1111
48
1219
56
1422
H
8
203
15.5
394
16.875
429
16.875
429
11.375
289
15.75
400
J
43.14
1096
49.8
1265
53.54
1360
53.54
1360
56.4
1433
62.85
1596
K
46.64
1185
53.3
1354
57.04
1449
57.04
1449
59.9
1521
66.35
1685
L
5.12
130
5.12
130.05
7.12
181
7.12
181
7.12
181
7.12
181
M
2.62
66
2.62
66
3.62
92
3.62
92
3.62
92
3.62
92
N
1.37
35
1.37
35
2.25
57
2.25
57
2.25
57
2.25
57
O
3.87
98
3.87
98
5
127
5
127
5
127
5
127
P
2.5
64
2.5
64
2.75
70
2.75
70
2.75
70
2.75
70
Q
2.5
64
2.5
64
3.5
89
3.5
89
3.5
89
3.5
89
1
Overhang dimensions for the optional starch dispenser are as follows:
UW35TV, 3.88 inches (9.86 cm); UW60TV, 1.75 inches (4.45 cm);
UW80TV and UW100TV, 0.33 inch (0.83 cm). (The starch dispenser does not overhang the UW125TV.) (No longer available.)
2 The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors only) adds
24 inches (60.96 cm) to combined machine dimensions E and G.
Table 1
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Specifications and Dimensions
3
2
3
4
8
5
1
6
7
F
E
C
G (BASE)
D (OVERALL)
A (BASE)
B (OVERALL)
10
L
11
9
M
12
Q
13
16
K
N
P
O
J
15
14
H
UW35TV - UW125TV MODELS
PHM735N
1
2
3
4
5
6
7
8
External Supply Control Mounting Bracket
(Models Through 6/30/08)
Door Unlock Button
Supply Valve Box
Emergency Stop Button
Supply Dispenser
Door Handle
Spray Rinse Nozzle
Recirculation Inlet
9
10
11
12
13
14
15
16
Water Inlet Valves
Steam Connection (Optional)
Shell Vent
Power Input (Electric Heat Models)
Power Input (Non-Electric Heat Models)
Drain (UW80TV, UW100TV and UW125TV
models only)
Drain
Overflow Vent
Figure 3
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
2
7
3
1
9
4
10
11
5
8
F
J
6
C
G (BASE)
A (BASE)
E
D (OVERALL)
B (OVERALL)
L
12
M
10
Q
13
K
11
15
N
P
O
J
H
14
TMB736N
UW150TV MODELS
PHM736N
1
2
3
4
5
6
7
External Supply Control Mounting Bracket
(Models Through 6/30/08)
Door Unlock Button
Emergency Stop Button
Supply Valve Box
Supply Dispenser
Spray Rinse Nozzle
Door Handle
8
9
10
11
12
13
14
15
Basket Jog Buttons
Recirculation Inlet
Shell Vent
Water Inlet Valves
Steam Connection (Optional)
Power Input
Drain
Overflow Vent
Figure 4
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Specifications and Dimensions
UW Design 1 and Design 2 Models
Starting 4/1/09 Through 10/3/10
(Refer to Figure 5 and Figure 6)
Dimension
35
60
80
100
125
150
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
A
30.125
765
35.625
905
41.125
1045
41.125
1045
48
1219
50
1270
B1
32.37
822
36.07
916
41.06
1043
41.06
1043
47.91
1217
50.23
1276
C
23.48
596
28.07
713
29.46
748
29.46
748
28.5
723
31.41
798
D
44.49
1130
47.24
1200
49.88
1267
55.85
1418
56.54
1436
62.43
1586
E
54.45
1383
64.52
1639
67.88
1724
67.88
1724
72.31
1837
78.9
2004
F2
36.15
918
38.87
987
45.48
1155
47.70
1212
48.52
1232
56.32
1431
G
7.66
195
14.72
374
15.92
404
15.92
404
11.9
302
15.73
400
H
43.15
1096
49.81
1265
53.54
1359
53.54
1359
56.4
1432
62.91
1598
J
46.65
1185
53.31
1354
57.04
1449
57.04
1449
59.9
1521
66.41
1687
K
5.12
130
5.12
130.05
7.12
181
7.12
181
7.12
181
7.12
181
L
2.62
66
2.62
66
3.62
92
3.62
92
3.62
92
3.62
92
M
1.37
35
1.37
35
2.25
57
2.25
57
2.25
57
2.25
57
N
3.87
98
3.87
98
5
127
5
127
5
127
5
127
O
2.5
64
2.5
64
2.75
70
2.75
70
2.75
70
2.75
70
P
2.5
64
2.5
64
3.5
89
3.5
89
3.5
89
3.5
89
1
Overhang dimensions for the optional starch dispenser are as follows:
35, 3.88 inches (9.86 cm); 60, 1.75 inches (4.45 cm);
80 and 100, 0.33 inch (0.83 cm). (The starch dispenser does not overhang the 125.) (No longer available.)
2 The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors only) adds
24 inches (60.96 cm) to combined machine dimensions E and G.
Table 2
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
3
2
3
4
8
5
1
6
7
E
C
F (BASE)
D (OVERALL)
A (BASE)
B (OVERALL)
K
9
L
10 11
12
P
13
16
J
M
O
N
H
15
14
G
35 - 125 MODELS
PHM808N
PHM808N
1
2
3
4
5
6
7
8
External Supply Control Mounting Bracket
(Models Through 6/30/08)
Door Unlock Button
Supply Valve Box (optional)
Emergency Stop Button
Supply Dispenser
Door Handle
Spray Rinse Nozzle (optional)
Recirculation Inlet
9
10
11
12
13
14
15
16
Water Inlet Valves
Steam Connection (Optional)
Shell Vent
Power Input (Electric Heat Models)
Power Input (Non-Electric Heat Models)
Drain (80, 100 and 125 models only)
Drain
Overflow Vent
Figure 5
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Specifications and Dimensions
2
7
3
1
9
4
10
11
5
8
F
J
6
C
G (BASE)
D (OVERALL)
A (BASE)
B (OVERALL)
E
L
12
M
10
Q
13
K
11
15
N
P
O
J
H
14
TMB736N
150 MODELS
PHM736N
1
2
3
4
5
6
7
External Supply Control Mounting Bracket
(Models Through 6/30/08)
Door Unlock Button
Emergency Stop Button
Supply Valve Box
Supply Dispenser
Spray Rinse Nozzle
Door Handle
8
9
10
11
12
13
14
15
Basket Jog Buttons
Recirculation Inlet
Shell Vent
Water Inlet Valves
Steam Connection (Optional)
Power Input
Drain
Overflow Vent
Figure 6
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
UW Design 3 Models starting 10/4/10
(Refer to Figure 7 and Figure 8)
Dimension
35
60
80
100
125
150
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
A
30.125
765
35.625
905
41.125
1045
41.125
1045
48
1219
50
1270
B
32.37
822
36.07
916
41.06
1043
41.06
1043
47.91
1217
50.23
1276
C
23.41
595
28.07
713
29.29
744
29.29
744
28.5
723
31.41
798
D
45.27
1150
46.81
1189
50
1270
56.03
1423
55.04
1398
62
1575
E
54.32
1380
64.40
1636
67.75
1721
67.75
1721
72.18
1833
78.77
2001
F1
36.18
919
38.87
987
45.56
1157
48.08
12.21
48.25
1226
56.26
1429
G
6.79
172
14.73
374
15.94
405
15.94
405
11.71
297
15.69
399
H
47.06
1195
53.71
1364
56.42
1433
56.42
1433
57.92
1471
64.36
1635
J
2.3
58
2.3
58
2.3
58
2.3
58
2.3
58
2.3
58
K
4.9
124
4.9
124
4.9
124
4.9
124
4.9
124
4.9
124
L
7.8
198
7.8
198
7.8
198
7.8
198
7.8
198
7.8
198
M
10.4
264
10.4
264
10.4
264
10.4
264
10.4
264
10.4
264
N
2.6
66
2.6
66
2.6
66
2.6
66
2.6
66
2.6
66
O
2.85
72
2.85
72
2.85
72
2.85
72
2.85
72
2.85
72
1
The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors
only) adds 24 inches (60.96 cm) to combined machine dimensions E and G.
Table 3
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Specifications and Dimensions
1
2
3
3
6
4
4
5
5
E
F
E
C
C
F (BASE)
G (BASE)
D (OVERALL)
D (OVERALL)
A (BASE)
A (BASE)
B (OVERALL)
B (OVERALL)
M
N
L
M
K
L
J
K
N
O
8
9
6
7
9
10
10
11
13
14
7
8
O
P
N
O
H
J
12
13
11
12
G
H
35 -- 125
125 MODELS
MODELS
35
PHM806N
PHM806N
1
2
3
4
5
6
7
Door Unlock Button
Emergency Stop Button
Supply Dispenser
Door Handle
Spray Rinse Nozzle (optional)
Water Inlet Valves
Steam Connection (Optional)
8
9
10
11
12
13
Shell Vent
Power Input (Electric Heat Models)
Power Input (Non-Electric Heat Models)
Drain (80, 100 and 125 models only)
Drain
Overflow Vent
Figure 7
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
1
2
8
3
6
9
4
7
F
J
5
C
G (BASE)
A (BASE)
E
D (OVERALL)
B (OVERALL)
N
M
9
L
8
K
11
P
O
10
O
13
J
H
12
PHM807N
150 MODELS
PHM807N
1
2
3
4
5
6
7
Door Unlock Button
Emergency Stop Button
Supply Valve Box
Supply Dispenser
Spray Rinse Nozzle
Door Handle
Basket Jog Buttons
8
9
10
11
12
13
Shell Vent
Water Inlet Valves
Steam Connection (Optional)
Power Input
Drain
Overflow Vent
Figure 8
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Specifications and Dimensions
Machine Foundation Requirements
A 6 inch (153 mm) (for 35 and 60 2-speed, L-speed
and M-speed models) or a 12 inch (305 mm) (for all
other models) thickness of 3500 psi reinforced
concrete foundation is absolutely necessary because of
the high extract speed and the G-forces exerted.
When designing floors or foundations, refer to Table 3
for Floor Load Data for all model sizes. If the
foundation requirements have been met, proceed to
Mounting Bolt Installation Requirements section.
For new foundations a bolt-locator fixture or rebar
frame is available and a preferred option. This rigid
welded assembly made of reinforcing rod and
mounting bolts is designed to be embedded in
concrete. Refer to Figure 11.
The washer-extractor must be anchored to a smooth
level surface so that the entire base of the machine is
supported and rests on the mounting surface. (Do not
support the washer-extractor on only four points.)
Make sure to grout machine. Refer to Figure 10 and
Figure 11.
NOTE: Do not mount on wooden floors, above
ground level, or over basements. Installation must
be “slab on grade” or equal.
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
extract.
CAUTION
Ensure that the machine is installed on a
floor that is level to within 3/8 inch when
the machine is grouted. Also ensure that
the floor is of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
W760
WARNING
To reduce the risk of fire, this appliance
must be bolted to an uncovered concrete
floor.
W743
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Concrete Foundation Pad
Installation
6. Wet the hole around the cement foundation well
and brush the exposed foundation with cement
grout.
A concrete foundation and pad may be constructed to
elevate the machines. Care must be exercised in the
design of the foundation pad due to the force exerted
by the machine during extract. This concrete base
(recommended not to exceed 8 inches [20.32 cm])
(above existing floor) must be poured, reinforced with
rebar and tied to the existing 6 inch (153 mm) (for 35
and 60 2-speed, L-speed and M-speed models) or 12
inch (305 mm) (for all other models) minimum floor.
Refer to Figure 9 and Table 3.
7. Completely fill with a minimum of 6 inch (153
mm) (for 35 and 60 2-speed, L-speed and
M-speed models) or 12 inch (305 mm) (for all
other models) of 3500 psi concrete up to the
existing foundation level plus any added level for
the desired elevated pad. The concrete must be
poured so that the entire foundation and pad
cures as one piece.
IMPORTANT: Do NOT install a pad on top of the
existing floor. The foundation and pad must be
constructed and tied together as one piece.
If the existing floor is not reinforced concrete at least 6
inch (153 mm) (for 35 and 60 2-speed, L-speed and
M-speed models) or 12 inch (305 mm) (for all other
models) thick over a solid foundation, the following
steps must be performed (refer to Figure 9):
8. For new foundations only a bolt-locator fixture
or a rebar frame is available and a preferred
option. Embed the mounting bolts or rebar frame
as the concrete is poured. Ensure that the bolt
threads extend 2 inches (51 mm) for 35 - 125
models and 3 inches (76 mm) for 150 models
above floor level.
9. Allow concrete to dry.
10. Proceed to Machine Mounting and Grouting
section.
1. Cut a hole larger on all sides than the machine
base through the existing floor. The foundation
should extend a minimum of 9 inches (229 mm)
for 35 models or 12 inches (305 mm) for 60 - 150
models out from the machine on all sides.
NOTE: If the washer-extractor installation will
include the Premium Wet Clean Module, the
elevated base must be designed to accommodate the
additional depth of 24 inches (60.96 cm).
2. Excavate to a depth of 18 inches (457 mm) from
the top of the existing floor.
For technical assistance, contact your local distributor
or call Alliance Laundry Systems at (920) 748-3121.
3. Produce a PYRAMID-SHAPED hole by
excavating the bottom of the hole to a width 6
inches wider on each side than the width of the
top of the hole.
4. If installing a foundation and pad, prepare a form
for the above-ground portion of the foundation.
Verify that the top of the foundation is level. The
height of the foundation pad must not exceed 8
inches (203 mm) above the existing floor.
5. Refill with compacted fill dirt, making sure to
allow for correct concrete thickness.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Specifications and Dimensions
Brush with
Cement Grout
Brush with
Cement Grout
5
1
3
3
Brush with
Cement Grout
LENGTH FOR ONE MACHINE
3
3
4
2
6
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
PHM790N
Figure 9
35
1
60
2-Speed,
L-Speed and M-Speed
6 in. (153 mm)
Variable-Speed
12 in. (305 mm)
26
80
100
125
150
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
2
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
3
9 in.
(229 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
4
36 in.
(914 mm)
36 in.
(914 mm)
43.75 in.
(1111 mm)
43.75 in.
(1111 mm)
48 in.
(1219 mm)
56 in.
(1422 mm)
5
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
6
48.125 in.
(1222 mm)
59.625 in.
(1514 mm)
65.125 in.
(1654 mm)
65.125 in.
(1654 mm)
72 in.
(1829 mm)
74.25 in.
(1886 mm)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Floor Load Data
Static and dynamic loads on the floor or foundation are
shown in Table 4 and Table 5.
UWTV Pocket Hardmount Floor Load Data (Models Through 3/31/09)
Specifications
Design
Series
35
60
80
Static floor load, lbs (kN)
U1 and
greater
1272 (5.66) 1677 (7.45) 2292 (10.2)
Static pressure,
lbs/ft2
U1 and
greater
169 (8.08)
187 (8.94)
184 (8.79)
100
125
150
2490 (11.1)
3283 (14.6)
3936 (17.5)
199 (9.6)
205 (9.8)
202 (9.7)
Dynamic floor load, lbs (kN) U1 and
greater
1648 (7.33) 2824 (12.6) 3679 (16.36) 3690 (16.41) 5011 (22.29) 4358 (19.4)
Dynamic pressure,
lbs/ft2 (kN/m2)
219 (10.5)
317 (15.2)
295 (14.2)
295 (14.2)
312 (15)
224 (11)
15
13.6
12.8
12.8
9.7
11.7
U1 and
greater
Dynamic load frequency, Hz U1 and
greater
1
Maximum vertical load,
lbs (kN)
U1 and
greater
2719 (12.1) 4168 (18.5) 5482 (24.38) 5561 (24.73) 7559 (33.62) 7508 (33.4)
2
Minimum vertical load,
lbs (kN)
U1 and
greater
576 (2.56) 1450 (6.45) 1852 (8.24)
Base moment, lb/ft (kN/m)
U1 and
greater
4249 (5.8) 8895 (12.1) 11951 (16.2) 11984 (16.3) 16606 (22.5) 16707 (22.7)
1
2
1794 (8.0)
2434 (10.8)
1208 (5.4)
Acting in the downward direction against the floor.
Acting in the upward direction away from the floor.
Table 4
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Specifications and Dimensions
UWL, UWN AND UWU Pocket Hardmount Floor Load Data (Models Starting 4/1/09)
Specifications
Static floor load,
lbs. (kN)
Static pressure,
lbs/ft2 (kN/m2)
Dynamic floor load,
lbs. (kN)
Dynamic pressure,
lbs/ft2 (kN/m2)
Dynamic load
frequency, Hz
Design
Series
Speed
35
60
80
100
125
150
U1 and
greater
Variable-speed
1272
(5.66)
1442
(6.42)
2292
(10.2)
2490
(11.1)
3283
(14.6)
3936
(17.5)
2-speed
1272
(5.66)
1442
(6.42)
N/A
N/A
N/A
N/A
L-speed
1272
(5.7)
1442
(6.4)
N/A
N/A
N/A
N/A
M-speed
1272
(5.7)
1442
(6.4)
2292
(10.2)
2490
(11)
3283
(14.6)
N/A
Variable-speed
169
(8.08)
162
(7.7)
184
(8.79)
199
(9.6)
205
(9.8)
202
(9.7)
2-speed
169
(8.08)
162
(7.7)
N/A
N/A
N/A
N/A
L-speed
169
(8)
162
(7.7)
N/A
N/A
N/A
N/A
M-speed
169
(8)
162
(7.7)
184
(8.8)
199
(9.5)
205
(9.8)
N/A
Variable-speed
1576
(7)
2704
(12)
3603
(16.36)
4504
(16.41)
3746
(22.29)
4501
(19.4)
2-speed
473
(2.1)
950
(4.23)
N/A
N/A
N/A
N/A
L-speed
525
(2,3)
900
(4)
N/A
N/A
N/A
N/A
M-speed
944
(4.2)
1624
(7.2)
2167
(9.6)
2708
(12)
3380
(15)
N/A
Variable-speed
380
(18.2)
466
(22.34)
472
(22.63)
559
(26.8)
439
(21)
433
(20.8)
2-speed
233
(11.2)
269
(6.3)
N/A
N/A
N/A
N/A
L-speed
240
(11.5)
263
(12.59)
N/A
N/A
N/A
N/A
M-speed
295
(14.1)
344
(16.5)
357
(17)
416
(19.9)
416
(19.9)
N/A
Variable-speed
15
13.6
12.8
12.8
9.7
11.7
2-speed
8.2
8.0
N/A
N/A
N/A
N/A
L-speed
8.63
7.82
N/A
N/A
N/A
N/A
M-speed
11.58
10.5
9.9
9.9
9.2
N/A
U1 and
greater
U1 and
greater
U1 and
greater
U1 and
greater
Table 5 (continued)
Table 5
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Table 5 (continued)
UWL, UWN AND UWU Pocket Hardmount Floor Load Data (Models Starting 4/1/09)
Specifications
1Maximum vertical
load, lbs. (kN)
Base moment,
lb/ft (kN/m)
Design
Series
Speed
35
60
80
100
125
150
U1 and
greater
Variable-speed
2848
(12.7)
4146
(18.4)
5895
(26.2)
6994
(31.1)
7028
(31.3)
8437
(37.52)
2-speed
1745
(7.8)
2392
(.41)
N/A
N/A
N/A
N/A
L-speed
1797
(8)
2342
(10.4)
N/A
N/A
N/A
N/A
M-speed
2216
(9.9)
3066
(13.6)
4459
(19.8)
5198
(23)
6663
(29.6)
N/A
Variable-speed
4076
(5.54)
8492
(11.5)
11688
(15.9)
14611
(19.9)
12488
(17)
17231
(23.4)
2-speed
1224
(1.7)
2985
(4)
N/A
N/A
N/A
N/A
L-speed
1356
(1.8)
2826
(3.8)
N/A
N/A
N/A
N/A
M-speed
2442
(3.3)
5099
(6.9)
7029
(9.6)
8786
(11.9)
11268
(15.3)
N/A
U1 and
greater
N/A = Not Applicable
1 Acting in the downward direction against the floor.
Table 5
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Specifications and Dimensions
Mounting Bolt Installation
Requirements
For new foundations a bolt-locator fixture or rebar
frame is available and a preferred option. This rigid
welded assembly made of reinforcing rod and
mounting bolts is designed to be embedded in
concrete. Refer to Figure 11.
Approved Foundations Only
NOTE: If installing expansion bolts into an
elevated concrete foundation pad, the concrete
foundation pad should extend a minimum of 9
inches (229 mm) for 35 machines or 12 inches (305
mm) for 60 - 150 machines out from the machine
base on all sides. Refer to Figure 9.
1
2
A bolt kit consisting of eight bolts is available as an
option. 35 machines use 5/8-11 x 8 inch bolts.
60 – 125 machines use 3/4-10 x 8 inch bolts. 150
machines use 3/4-10 x 10 inch grade 5 bolts. The bolts
should be embedded in a 3500 psi (241 bar) minimum
reinforced concrete floor that is a minimum of 6 inches
(153 mm) (for 35 and 60 2-speed, L-speed, and
M-speed models) or a 12 inch (305 mm) (for all other
models) thick. Use the mounting bolt layouts in
Mounting Bolt Hole Locations section.
On 35 – 125 machines, the threaded end of the bolts
should extend 2 inches (5.08 cm) above the mounting
surface. On 150 machines, the threaded end of the
bolts should extend 3 inches above the mounting
surface.
Refer to Figure 10 for a typical installation of
individual mounting bolts.
3
4
PHM179N
PHM179N
1
2
3
4
Machine Frame Base
Mounting Bolt Threads
Grouting
Reinforcing Rod
Figure 11
1
2
0.75 in.
(19 mm)
3
2 in.
(51 mm)
4
8 in.
(203 mm)
PHM722N
PHM722N
1
2
3
4
Machine Frame Base
Mounting Bolt Threads
Grouting
Cement or Structural Epoxy
Figure 10
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Machine Mounting and Grouting
After the concrete has cured, proceed as follows:
1. Place the washer-extractor adjacent to the
foundation. Do not attempt to move the machine
by pushing on the sides. Always insert a pry bar
or other device under the bottom frame of the
machine to move it.
2. Remove the wood skid by unscrewing the
carriage bolts holding the skid to the bottom
frame of the washer-extractor.
3. Place the washer-extractor carefully over the
anchor bolts. Never attempt to lift the machine by
the door handle or by pushing on the cover
panels.
4. Raise and level the washer-extractor 0.5 inch
(1.27 cm) off the floor on three points, using
spacers such as nut fasteners.
5. Fill the space between the washer-extractor base
and the floor with a good quality non-shrinking
machinery precision grout to ensure a stable
installation. Grout completely under all frame
members. (Remove front panel and back panel to
gain access to all frame members.) Refer to
Figure 17. Force grout under machine base until
all voids are filled.
6. Remove the spacers carefully, allowing the
machine to settle into the wet grout.
F8138601
7. Before grout sets completely, make a drain
opening in the rear of the washer-extractor
grouting with a stiff piece of wire; this opening
should be approximately 1/2 inch (1.27 cm) wide
to allow any surface water build-up under the
base of the machine to drain away. Do not omit
this step.
8. Position the mounting bolt lockwashers and
locknuts on the anchor bolts and finger-tighten
locknuts to machine base.
9. After the grout is completely dry, tighten the
locknuts by even increments – one after the other –
until all are tightened evenly and the washerextractor is fastened securely to the floor.
10. After installing bolts using a rebar frame, torque
5/8 inch bolts (35 model) to 90 ft. lb. and torque
3/4 inch bolts (60-150 models) to 160 ft. lb.
When using bolts not specified by Alliance
Laundry Systems, refer to the specifications
provided with the bolt.
NOTE: Check and retighten the locknuts after five
to ten days of operation and every month
thereafter.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Specifications and Dimensions
Mounting Bolt Hole Locations
28.625 in.
(727 mm)
0.75 in.
(19 mm)
A
30.1875 in.
(767 mm)
36 in.
(914 mm)
A
43.28 in.
(1089 mm)
21.1875 in.
(538 mm)
34.5 in.
(876 mm)
40.1875 in.
(1022 mm)
34.16 in.
(868 mm)
26.125 in.
(664 mm)
2 in.
(51 mm)
2 in.
(51 mm)
30.125 in.
(765 mm)
35 MODEL
FRONT OF MACHINE
PHM630N
Figure 12
NOTE: Mounting holes marked “A” are on
V-speed Models only.
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
34.125 in.
(867 mm)
4.8125 in.
(122 mm)
39.25 in.
(997 mm)
1.25 in.
(32 mm)
36 in.
(914 mm)
9 in.
(229 mm)
44.8125 in.
(1138 mm)
10.75 in.
(273 mm)
1.25 in.
(32 mm)
34.5625 in.
(878 mm)
10.6875 in.
(271 mm)
2 in.
(51 mm)
31.625 in.
(803 mm)
2 in.
(51 mm)
0.75 in.
(19 mm)
35.625 in.
(905 mm)
60 VARIABLE-SPEED MODEL
FRONT OF MACHINE
PHM631N
Figure 13
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
39.625 in.
(1008 mm)
6.75 in.
(171 mm)
43.75 in.
(1111 mm)
9 in.
(229 mm)
2.25 in.
(57 mm)
52.1875 in.
(1326 mm)
13.625 in.
(346 mm)
46.3125 in.
(1176 mm)
2.25 in.
(57 mm)
39.75 in.
(1010 mm)
13.625 in.
(346 mm)
35.125 in.
(892 mm)
3 in.
(76 mm)
3 in.
(76 mm)
41.125 in.
(1045 mm)
0.75 in.
(19 mm)
80 / 100 MODELS
FRONT OF MACHINE
PHM632N
Figure 14
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
46.5 in.
(1181 mm)
7 in.
(178 mm)
10 in.
(254 mm)
48 in.
(1219 mm)
61.5 in.
(1562 mm)
15 in.
(381 mm)
55.47 in.
(1409 mm)
48.94 in.
(1243 mm)
15.25 in.
(387 mm)
23.25 in.
(591 mm)
23.25 in.
(591 mm)
48 in.
(1219 mm)
0.75 in.
(19 mm)
125 MODEL
FRONT OF MACHINE
PHM633N
PHM633N
Figure 15
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Specifications and Dimensions
56 in.
(1422 mm)
10.375 in.
(264 mm)
48.125 in.
(1223 mm)
51.375 in.
(1305 mm)
47.875 in.
(1216 mm)
10.375 in.
(264 mm)
57.4 in.
(1457 mm)
12.125 in.
(308 mm)
67.1 in.
(1704 mm)
15 in.
(381 mm)
4 in.
(102 mm)
1.5 in.
(38.1 mm)
1.5 in.
(38.1 mm)
47 in.
(1193 mm)
50 in.
(1270 mm)
150 MODEL
FRONT OF MACHINE
PHM778N
PHM778N
Figure 16
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Grout Placement
30.125 in.
(765 mm)
17.88 in.
(454 mm)
36 in.
(914 mm)
27.875 in.
(708.025 mm)
36 in.
(914.4 mm)
20 in.
(508 mm)
4.0625 in.
(103 mm) typical
22 in.
(559 mm)
4.0625 in.
(103 mm) typical
4.0625 in.
(103 mm) typical
30.13 in.
35.625 in.(765 mm)
(905 mm)
35 VARIABLE-SPEED MODEL
35 2-SPEED MODEL
PHM547N
PHM547N
PHM574N
PHM574N
35.63 in.
(905 mm)
35.625 in.
(905 mm)
11.9375 in.
(303 mm)
4.0625 in.
(103 mm) typical
35.9375 in.
(913 mm)
12 in.
27.5 in. (305 mm)
(699 mm)
36 in.
(914 mm)
27.5 in.
(699 mm)
4.0625 in.
(103 mm) typical
60 VARIABLE-SPEED MODEL
27.88 in.
(708 mm)
60 2-SPEED MODEL
PHM575N
4.0625 in.
(103 mm) typical
4.0625 in.
(103 mm) typical
PHM548N
PHM548N
PHM575N
41.125 in.
(1044 mm)
41.125 in.
(1044 mm)
14 in.
(356 mm)
43.75 in.
(1111 mm)
4.0625 in.
(103 mm)
typical
17.5 in.
(445 mm)
33 in.
(838 mm)
80 MODEL
43.8125 in.
(1113 mm)
4.0625 in.
(103 mm) typical
PHM576N
PHM576N
20.6875 in.
(526 mm)
33 in.
(838 mm)
100 MODEL
4.0625 in.
(103 mm) typical
4.0625 in.
(103 mm) typical
PHM192N
50 in.
(1270 mm)
48 in.
(1219 mm)
3.25 in.
(83 mm)
34 in.
(863.6 mm)
4.06 in.
(103 mm)
typical
24.31 in.
(617 mm)
10.875 in.
(276 mm)
56 in.
(1422 mm)
48 in.
(219 mm)
39.88 in.
22 in. (1013 mm)
(559 mm)
125 MODEL
4.06 in.
(103 mm)
typical
8 in.
(203.2 mm)
typical
PHM180N
8 in.
(203.2 mm)
typical
150 MODEL
PHM605N
PHM605N
Figure 17
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Specifications and Dimensions
Gap Setting for Vibration Switch
After the machine has been properly installed, the
vibration switch gap must be verified. To locate the
vibration switch refer to Figures 18, 19 and 20. For
UniLinc models, while the control is displaying the
Inputs Outputs Menu the alarm will sound when the
frame switch is activated. To verify and set the
vibration switch gap use the following procedures:
WARNING
Verify Vibration Switch Gap
(for 35-125 Pound Models):
1. Insert 0.009 inch feeler gauge between the
adjustment bolt and the vibration switch; the
alarm must not activate.
2. Remove the feeler gauge
3. Insert 0.010 inch feeler gauge (supplied with
machine) between the adjustment bolt and the
vibration switch; the alarm must activate.
4. Remove the feeler gauge.
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
For UniLinc Models, Navigate to the Inputs
Outputs Menu:
1. From the Cycle Menu press and hold the
,
,
keys to enter the System Menu.
2. Press the arrow keys to highlight the Diagnostic
box.
3. Press the
Menu.
key to enter the Diagnostic
4. Press the
key to enter the Test Menu.
Verify Vibration Switch Gap
(For 150 Pound Design 1 Models):
1. Insert the 0.010 inch feeler gauge (supplied with
machine) between the adjustment bolt and the
vibration switch.
2. If alarm is active: Slowly loosen adjustment bolt
until the alarm stops.
3. Very slowly tighten the adjustment bolt until the
alarm activates. The adjustment bolt must be
tightened very slowly to prevent over adjustment.
4. Remove the feeler gauge.
5. Press the arrow keys to highlight the Inputs
Outputs box.
6. Press the
Menu.
5. Adjust the vibration switch adjustment bolt if
necessary.
key to enter the Inputs Outputs
5. Verify the Frame Switch setting.
To adjust the vibration switch gap on the 150 models,
move the vibration switch by adjusting the jam nuts on
the vibration switch.
For UniLinc models, to return to the Cycle Menu press
BACK key several times until Cycle Menu is
displayed.
Verify Safety Switch Operation
(For 150 Pound Design 2 Models):
1. Place a large magnet above the normally-closed
ball switch to verify switch operation.
IMPORTANT: UW150 Design 2 machines are
manufactured with a normally-closed ball switch
and should not require any adjustment. To avoid
nuisance tripping, machine must be level with a
summed value of 3/8 inch front to back and right to
left to the earth. If switch is tripped, check if
machine is level and then for pour grouting and
broken anchor bolts. DO NOT BYPASS SAFETY
SWITCH. Contact a qualified service technician
for further assistance.
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
35 Pound Model
ADJUSTMENT
BOLT
VIBRATION
SWITCH
PHM794N
PHM794N
Figure 18
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Specifications and Dimensions
60, 80, 100 and 125 Pound Models
VIBRATION
SWITCH
ADJUSTMENT BOLT
PHM795N
PHM795N
Figure 19
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Design 1 150 Pound Model
VIBRATION SWITCH
PHM716N
PHM716N
Figure 20
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Specifications and Dimensions
Drain Connection Requirements
DRAIN TROUGH CONFIGURATION
A drain system of adequate capacity is essential to
washer-extractor performance. The water can empty
directly into a sump or floor drain. Figure 21 shows
the drain line configuration and Figure 22 shows the
drain trough configuration.
1
2
DRAIN LINE CONFIGURATION
3
4
1
2
5
6
3
7
PHM621N
PHM789N
1
2
3
Overflow
Vent
Trap (As required by local codes)
NOTE: If a flexible connection is made directly to a
drain system, the drain system must be vented to
prevent an air lock and siphoning.
Figure 21
A flexible connection must be made to a vented drain
system to prevent an air lock and to prevent siphoning.
IMPORTANT: Washer-extractor must be installed
in accordance with all local codes and ordinances.
1
2
3
4
5
6
7
Rear of Machine
Drain Pipe
1 Inch Minimum Air Gap
Steel Grate
Drain Trough
Strainer
Waste Line
Figure 22
Refer to Table 6 for capacity-specific drain
information.
Installation of additional washer-extractors will
require proportionately larger drain connections. Refer
to Table 7.
If proper drain size is not available or practical, a surge
tank is required. A surge tank in conjunction with a
sump pump should be used when gravity drainage is
not possible, such as in below-ground-level
installations.
Before any deviation from specified installation
procedures is attempted, the customer or installer
should contact the distributor.
Increasing the drain hose length, installing elbows, or
causing bends will decrease drain flow rate and
increase drain times, impairing washer-extractor
performance.
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
IMPORTANT: Do not block the overflow vent
above the drain line.
If water or suds flow from the overflow vent and the
machine has been verified to be operating properly
with proper water levels and correct amount of laundry
chemicals, a drain line may be added to the vent and
routed to a drain trough.
1. Remove the riveted bracket on the rear panel for
access to the overflow vent pipe.
2. Route a drain pipe from the vent pipe to a drain
trough. Drain pipe should be routed straight
across or down and be suspended above drain
trough by at least 3 inches (7.62 cm).
IMPORTANT: Do not route the overflow vent pipe
to a direct drain system.
Drain Information
Specifications
Drain connection size, O.D., in. (mm)
with second drain:
35
60
80
100
125
150
2.375 (60)
3 (76)
3 (76)
3 (76)
3 (76)
3 (77)
1
1
2
2
2
2
35 (132)
64 (242)
120 (454)
120 (454)
140 (530)
140 (530)
5 (142)
6 (170)
9 (255)
11 (311)
13 (368)
13 (368)
Number of drain outlets
Drain flow capacity, gal/min. (l/min.)
3
Recommended drain pit size, ft (l) †
†Sized for one machine using overflow level.
Table 6
Drain Line Sizing
Minimum Drain I.D., in. (mm)
Model
Number of Machines
1
2
3
4
35
3 (76.2)
3 (76.2)
3.5 (88.9)
4 (102)
60
3 (76.2)
4 (102)
6 (152)
6 (152)
80
4 (102)
6 (152)
6 (152)
8 (203)
100
4 (102)
6 (152)
6 (152)
8 (203)
125
4 (102)
6 (152)
6 (152)
8 (203)
150
4 (102)
6 (152)
6 (152)
8 (203)
Table 7
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Specifications and Dimensions
Water Connection
WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748
Maximum water inlet temperature is 190° Fahrenheit
(88° Celsius).
Water Supply Information
Specifications
35
60
80/100
125/150
2
2
2
2
Main fill water inlet size, in. (mm)
3/4 (19)
3/4 (19)
3/4 (19)
1 (25.4)
Number of Spray Rinse water inlets
2
2
2
2
Spray rinse water inlet size, in. (mm)
3/4 (19)
3/4 (19)
3/4 (19)
3/4 (19)
Number of main fill water inlets
Recommended pressure, psi (bar)
Inlet flow capacity (80 psi),
gal/min. (l/min)
30 – 85 (2 – 5.7)
31 (117)
39 (148)
41 (155)
48 (182)
Table 8
Connections should be supplied by hot and cold water
lines of at least the sizes shown in the Water Supply
Line Sizing table. Installation of additional machines
will require proportionately larger water lines. Refer to
Table 9. Flush the water lines before connecting them
to the machine.
44
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
To connect water service to machine with rubber
hoses, use the following procedure:
Water Supply Line Sizing
Model
1. Before installing hoses, flush the water system
for at least two minutes.
Number
of Machines
Supply Line Size, in. (mm)
Main
Hot/Cold
1
1 (25)
0.75 (19)
2
1.5 (38)
1 (25)
3
2 (50)
1.25 (32)
4
2 (50)
1.5 (38)
1
1.25 (32)
1 (25)
2
2 (50)
1.25 (32)
3
2 (50)
1.5 (38)
4
2.5 (64)
2 (50)
1
1.25 (32)
1 (25)
2
2 (50)
1.25 (32)
Suitable air cushions should be installed in supply
lines to prevent “hammering.” Refer to Figure 23.
3
2 (50)
1.5 (38)
4
2.5 (64)
2 (50)
For machines labeled with the CE mark, backsiphon
protection devices must be installed previous of all
machine water inlet valves in accordance with
accepted European standards.
1
1.5 (38)
1 (25)
2
2 (50)
1.5 (38)
3
2 (50)
1.5 (38)
4
2.5 (64)
2 (50)
1
2 (50)
1.25 (32)
2
2.5 (64)
2 (50)
3
2.5 (64)
2 (50)
4
2.5 (64)
2.5 (64)
1
2 (50)
1.25 (32)
2
2.5 (64)
2 (50)
3
2.5 (64)
2 (50)
4
2.5 (64)
2.5 (64)
2. Check filters in the washer-extractor’s inlet hoses
for proper fit and cleanliness before connecting.
3. Hang the hoses in a large loop; do not allow them
to kink.
If additional hose lengths are needed, use flexible
hoses with screen filters. Each hose should have a
screen filter installed to keep rust and other foreign
particles out of the water inlet valves.
Pressure of 30 – 85 psi (2 – 5.7 bar) provides best
performance. Although the washer-extractor will
function properly at lower pressures, increased fill
times will occur.
35
60
80
100
1
125
150
Table 9
2
P038I
P038I
1
2
Air Cushions (Risers)
Water Supply Faucets
Figure 23
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Specifications and Dimensions
Electrical Installation Requirements
IMPORTANT: Electrical ratings are subject to
change. Refer to serial decal for electrical ratings
information specific to your machine.
WARNING
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Alliance Laundry Systems
warranty does not cover components that fail as a
result of improper input voltage.
Make sure the correct transformer jumper (208 Volt or
240 Volt) is in place. Refer to the “optional” Electrical
Service Connection label located on the back of the
machine near the electrical service input for machine
electrical requirements. Refer to Figure 24.
OPTIONAL ELECTRICAL SERVICE
CONNECTION BASED ON
AVAILABILITY
This unit may be field converted
by a QUALIFIED Electrician to
the following 200-208 Volts
and/or 50 Hertz.
PRIOR TO CONNECTING
ELECTRICAL SERVICE,
COMPLETE THE FOLLOWING
WARNING
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
troubleshooting. Disconnect power from
the machine and wait 3 minutes before
removing the control box cover, and
before attempting any service
procedures.
W702
WARNING
Ensure that a ground wire from a proven
earth ground is connected to the ground
lug near the input power block on this
machine. Without proper grounding,
personal injury from electric shock could
occur and machine malfunctions may be
evident.
SW008
46
Electrical connections are made at the rear of the
machine. The machine must be connected to the
proper electrical supply shown on the identification
plate attached to the rear of the machine, using copper
conductors only.
F8099701R1
200-208 VAC CONVERSION
VAC: 200-208
PHASE: *
AMPS: *
WIRES & GROUND: *
REC'D BREAKER: *
1. Refer to the Control Transformer area on
the Control Option Diagram.
2. Remove the "240V" Transformer Jumper in
the control box.
3. Replace with "208V" Transformer Jumper
found in the diagram pack.
4. Sign off below.
200-208VAC
Operation
* As indicated on
original serial plate
Transformer Jumper
208V
50Hz CONVERSION
1. Refer to the Control Option Diagram.
2. Remove the wire from the 60Hz tap on drain
valve(s).
3. Connect the wire to the 50Hz Tap on all
drain valves.
Connection Drain Valve(s)
4. Sign off below.
for 50Hz
Operation Only
50Hz
60Hz
on
(SIGN)
(DATE)
50Hz
Operation
N
on
(SIGN)
(DATE)
O, Q, X AND Y – VOLTAGE MODELS
PHM740N
PHM740N
N, P AND R – VOLTAGE MODELS
PHM756N
PHM756N
Figure 24
On variable-speed models, the AC inverter drive
requires a clean power supply free from voltage spikes
and surges. A voltage monitor should be used to check
incoming power. The customer’s local power company
may provide such a monitor.
The following conditions require corrective action,
contact the local utility to adjust the voltage. If the
local utility cannot adjust the input voltage, install a
buckboost transformer to lower the input voltage.
Input voltage is above 240V or 480V, phase to ground
voltage exceeds 125% of normal line to line voltage,
or 240V open delta configuration (stinger leg).
Contact the distributor or the manufacturer for
assistance.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
On variable-speed models, the AC drive provides
thermal overload protection for the drive motor.
However, a separate three-phase circuit breaker must
be installed for complete electrical overload
protection. This prevents damage to the motor by
disconnecting all legs if one should be lost
accidentally. Check the serial plate on the back of the
washer-extractor for recommended circuit breaker
requirements size.
WARNING
Electrically heated machines DO NOT
require dual power sources. Do not
connect customer power or customer load
to the Internal Load Distribution terminal
block. Refer to the machine electrical
schematic for details.
W759
IMPORTANT: Do NOT use fuses in place of a
circuit breaker.
2
L1
CAUTION
L2
1
Do not use a phase adder on any variablespeed machine.
SERVICE
GROUND
SW037
The washer-extractor should be connected to an
individual branch circuit not shared with lighting or
other equipment.
The connection should be shielded in a liquid-tight or
approved flexible conduit with proper conductors of
correct size installed in accordance with the National
Electric Code or other applicable codes. The
connection must be made by a qualified electrician
using the wiring diagram provided with the washerextractor, or according to accepted European standards
for equipment labeled with the CE mark.
Refer to serial plate for recommended circuit breaker
size and determine wire size based on local code
requirements.
L3
CHASIS
3
TB1
PHM
MACHINES WITH ELECTRIC HEAT
PHM700N
1
2
3
Grounding Lug: Connect to proven earth
ground
Customer Input Power Terminals
Internal Load Distribution - DO NOT connect
customer power source or load.
Figure 25
Refer to serial plate for recommended wire sizes for
runs up to 50 feet (15.24 meters). Use next larger size
for runs of 50 to 100 feet (15.24 to 30.48 meters). Use
2 sizes larger for runs greater than 100 feet (30.48
meters).
1
SERVICE
GROUND
For personal safety and for proper operation, the
washer-extractor must be grounded in accordance with
state and local codes. If such codes are not available,
grounding must conform with the National Electric
Code, article 250 (current edition) or accepted
European standards for equipment labeled with the CE
mark. The ground connection must be made to a
proven earth ground, not to conduit or water pipes.
Refer to Figure 25 and 26.
2
CHASIS
L1
L2
L3
TB1
P
MACHINES WITHOUT ELECTRIC HEAT
PHM721N
1
2
Grounding Lug: Connect to proven earth
ground
Customer Input Power Terminals
Figure 26
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Specifications and Dimensions
Machines can be converted for lower voltage
operation and/or 50 Hz operation. Refer to conversion
label by serial plate for details.
After electrical installation is complete, run the
machine through a test cycle and check for a clockwise
basket rotation during the extract step. If rotation is not
clockwise, disconnect the power from the machine and
have a qualified electrician reverse any 2 motor leads.
48
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Table 5 (continued)
Voltage Designation
Electric Heat Machines
*mm2
*AWG
Breaker
Full Load
Amps
*mm2
*AWG
Breaker
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
Model
X
200 – 240
50/60
1/3
2/3
12/8
15/15 14/14
2.5/2.5
NOT AVAILABLE
X
200 – 240
50/60
1/3
2/3
15/8
20/15 12/14
4/2.5
NOT AVAILABLE
Q
200 – 240
50/60
3
3
8
15
14
2.5
42
50
6
16
O**
208 – 240
60
3
3
7
20
12
4
38
50
6
16
R
380 – 480
50/60
3
3
6
15
14
2.5
23
30
10
6
440 – 480
50/60
3
3
6
15
14
2.5
23
30
10
6
380 – 415
50/60
3
3
6
15
14
2.5
23
30
10
6
X
200 – 240
50/60
1/3
2/3
15/9
Q
200 – 240
50/60
3
3
9
15
14
2.5
71
80
3
25
O**
208 – 240
60
3
3
11
30
10
6
66
80
3
30
R
380 – 480
50/60
3
3
7
15
14
2.5
37
40
8
10
440 – 480
50/60
3
3
7
15
14
2.5
37
40
8
10
380 – 415
50/60
3
3
7
15
14
2.5
37
40
8
10
Q
200 – 240
50/60
3
3
9
15
14
2.5
105
110
1
50
Q
200 – 240
50/60
3
3
14
20
14
2.5
105
110
1
50
R
380 – 480
50/60
3
3
10
15
14
2.5
39
40
8
10
N
440 – 480
50/60
3
3
10
15
14
2.5
39
40
8
10
380 – 415
50/60
3
3
10
15
14
2.5
39
40
8
10
(Through
7/31/09)
(Starting
8/1/09)
35
Non-Electric Heat
Machines (Standard)
(Through
10/1/10)
N
(Starting
10/4/10)
P
(Starting
10/4/10)
60
20/15 12/14
4/2.5
NOT AVAILABLE
(Through
10/1/10)
N
(Starting
10/4/10)
P
(Starting
10/4/10)
(Through
4/13/10)
(Starting
4/14/10)
80
(Through
10/1/10)
(Starting
10/4/10)
P
(Starting
10/4/10)
Table 10 (continued)
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Specifications and Dimensions
Voltage Designation
Electric Heat Machines
*mm2
*AWG
Breaker
Full Load
Amps
*mm2
*AWG
Breaker
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
Model
Q
200 – 240
50/60
3
3
10
15
14
2.5
108
110
1
50
Q
200 – 240
50/60
3
3
14
20
14
2.5
108
110
1
50
R
380 – 480
50/60
3
3
10
15
14
2.5
40
50
6
16
N
440 – 480
50/60
3
3
10
15
14
2.5
40
50
6
16
380 – 415
50/60
3
3
10
15
14
2.5
40
50
6
16
Q
200 – 240
50/60
3
3
9
15
14
2.5
R
380 – 480
50/60
3
3
8
15
14
2.5
440 – 480
50/60
3
3
8
15
14
2.5
74
80
4
25
380 – 415
50/60
3
3
8
15
14
2.5
65
70
4
25
Q
200 – 240
50/60
3
3
16
20
12
4
R
380 – 480
50/60
3
3
11
15
14
2.5
440 – 480
50/60
3
3
11
15
14
2.5
380 – 415
50/60
3
3
11
15
14
2.5
(Through
4/13/10)
(Starting
4/14/10)
100
Non-Electric Heat
Machines (Standard)
(Through
10/1/10)
(Starting
10/4/10)
P
(Starting
10/4/10)
NOT AVAILABLE
(Through
10/1/10)
125
N
(Starting
10/4/10)
P
(Starting
10/4/10)
(Through
10/1/10)
150
N
NOT AVAILABLE
(Starting
10/4/10)
P
(Starting
10/4/10)
* NOTE: Wire sizing listed in this table is based on Article 310, Table 310.16 of the NEC; at 104°F (40°C) ambient
temperature. Follow your local electrical codes. Use only copper conductors, rated for 194ºF (90°C) or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority having
jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers
for single phase machines only; three phase circuit breakers for all others.
** M30 Control Models only.
Table 10
50
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Steam Requirements
(Steam Heat Option Only)
For washer-extractors equipped with optional steam
heat, install piping in accordance with approved
commercial steam practices. Steam requirements are
shown in Table 11.
WARNING
NOTE: Failure to install the supplied steam filter
may void the warranty.
Never touch internal or external steam
pipes, connections, or components. These
surfaces can be extremely hot and will
cause severe burns. The steam must be
turned off and the pipe, connections, and
components allowed to cool before the
pipe can be touched.
SW014
Steam Supply Information
35
60
80
100
125/150
Steam inlet connection,
in. (mm)
1/2
(DN13)
1/2
(DN13)
1/2
(DN13)
1/2
(DN13)
3/4
(DN19)
Number of steam inlets
1
1
1
1
1
Recommended pressure,
psi (bar)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
85
(5.9)
85
(5.9)
85
(5.9)
85
(5.9)
85
(5.9)
Maximum pressure,
psi (bar)
Table 11
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Specifications and Dimensions
Chemical Injection Supply System
Undiluted chemical dripping can damage the washerextractor. Therefore, all chemical supply dispenser
pumps should be mounted below the washer’s
injection point. All dispenser tubing should also run
below the injection point. Loops do not prevent drips
if these instructions are not followed. Failure to follow
these instructions could damage the machine and void
the warranty. Figure 27 shows a typical Chemical
Injection Supply System.
WARNING
Wear eye and hand protection when
handling chemicals; always avoid direct
contact with raw chemicals. Read the
manufacturer’s directions for accidental
contact before handling chemicals.
Ensure an eye-rinse facility and an
emergency shower are within easy reach.
Check at regular intervals for chemical
leaks.
SW016
2
3
1
4
PHM825N
1
2
Injection Point
Loops
3
4
Chemical Dispenser Pump Outlet
PVC Pipe
Figure 27
52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Connecting External Liquid Supplies to the
Washer-Extractor
1
1. Remove knockout from supply dispenser. Refer
to Figure 28. Plugs are assembled inside the
tubing ring.
2
3
2. Install PG connector in hole with strain reliefs,
included in the seal nut.
4
5
3. Insert tubes through PG base. Do not remove
cups. Tube should extend into the plastic cup,
with the exception of the softener tube, which
should be routed to the outside of the cup.
6
4. Tighten the seal nut to prevent tubing from
escaping the assembly.
5. Before operating machine, confirm lid is
completely closed.
Do not attempt to make chemical injection electrical
connections to points other than those provided
specifically for that purpose by the factory.
PHM559N
PHM559N
1
2
3
4
5
6
Tubing from Pump
Seal Nut
Tubing Ring
Base
Lid
Nut
Figure 28
F8138601
Chemical Injection Supply System
Number of dry supply compartments
5
Number of external liquid supply
connections
8
Liquid supply connection size, in. (mm)
0.625 (15.9)
A bracket, which is located on the left side of the
control module, has been provided for mounting the
external supply controls. This bracket is present only
on models made through 6/30/08. Refer to Figures 5
through 10.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Specifications and Dimensions
1
2
3
4
5
6
PHM553N
PHM553N
1
2
3
Strain Relief for Liquid Chemical Supply Lines
Supply Dispenser Lid
Nozzles
4
5
6
Dry Supply Cups
Dry Supply Insert
Polypropylene Supply Dispenser
IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained.
Figure 29
54
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
External Supplies
For proper communication between the washerextractor and an external chemical supply system, it is
important for the signal power to be connected
properly. The included wiring diagram (F8133502)
shows several different options for safe and correct
wiring of this interface.
The preferred method for connecting the wiring from
the external chemical supply system to the washerextractor is to use the 300mA power of the washerextractor’s 24VAC control transformer, which is
intended strictly for this purpose. Other voltage and
current options are available, but require some wiring
changes and must be provided with an external power
source. Under no circumstances should the highvoltage machine supply connections or source be used
for the communication wiring.
EXTERNAL DISPENSER CONNECTIONS
EXAMPLE FOR EXTERNAL
ES 1 DISPENSER CONNECTION
RELAY COM
ES 2
ES 3
ES 4
ES 5
SUPPLY 1
24 VAC
External
Dispensing
System
ES 6
24 VAC COM
ES 7 JUMPER FOR INTERNAL
24 VAC SUPPLY
ES 8 CONNECTED
TO RELAY
T IF NOT
WIRING TO INTERNAL
RELAY
24 VAC SUPPLY
COM
RED
24 VAC
Internal
Supply
24 VAC
NOT
whi
00mA
Communication wiring connections, which include a
single row of identified terminal blocks, can be found
under a service panel at the upper back of the machine.
Refer to Figure 30.
PHM842N
Figure 30
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Specifications and Dimensions
Chemical Injection Using Internal 24VAC
Control Transformer
 Terminal “24VAC COM” is used to connect one
side of the internal control transformer to the
external dispenser input signals common.
NOTE: Using the Internal 24VAC 300 Milliamp
Control Transformer is recommended by Alliance
Laundry Systems.
 The second terminal is used to connect the other
side of the control transformer to the washerextractor output signals common through a red
jumper wire between “24VAC” and “RELAY
COM”. Refer to Figure 31.
IMPORTANT: DO NOT remove the red jumper
wire from the terminal strip.
There are 3 terminals necessary for this
connection option.
IMPORTANT: Do not use the transformer
terminals if an external power supply is used.
3
2
4
5
1
6
= Neutral
= Power
7
PHM821N
1
External Supply Power
5
Red Jumper Wire
2
Internal Control Transformer
6
24VAC Terminal
3
RELAY COM Terminal
7
24VAC COM Terminal
4
External Supply Common
Figure 31
56
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Chemical injection Using External AC
Power Source
IMPORTANT: The external power must supply
power of 240VAC or less and be protected at 3
Amps or less.
NOTE: An External AC Power Source is NOT
provided by Alliance Laundry Systems.
1. Remove the red jumper wire installed by the
factory between “24VAC”: and “RELAY COM”.
NOTE: Power for external supplies must not be
derived from the high-voltage main power
connection point.
2. Connect one side of the external power to the
“RELAY COM” and the other to the external
dispenser input signals common. Refer to
Figure 32.
3
1
4
2
= Neutral
= Power
5
PHM823N
1
External Supply Power
4
VAC Power Terminal
2
Red Jumper Wire
5
VAC RETURN Terminal
3
External Supply Common
Figure 32
CAUTION
Do not attempt to increase fuse rating or
alter wiring of external chemical supply
terminal strip in such as way that may
conflict with the suggested methods
provided on the Optional External Supply
Wiring Diagram.
W699
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
57
Specifications and Dimensions
External Supply Signals
Wash-cycle signals are provided to the external
chemical supply equipment and a “wait for the next
step” signal can be received from the supply
equipment.
For example, if ES1 is selected the K1 contact will
close and power will be supplied to Supply 1 Signal.
The contact will remain closed for the amount of time
programmed in control. Refer to Figure 33 for Internal
Supply Connection or Figure 34 for External AC
Connection.
3
= Neutral
= Power
1
2
PHM822N
1
ES1 Power supply
2
K1 Contact
3
Supply 1 Signal
Figure 33
58
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
3
= Neutral
= Power
1
2
PHM824N
1
ES1 Power supply
2
K1 Contact
3
Supply 1 Signal
Figure 34
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
59
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising