ICOM IC-A110EURO Instruction manual

Add to my manuals
24 Pages

advertisement

ICOM IC-A110EURO Instruction manual | Manualzz

IC-A110EURO-2 02.3.12 2:00 PM Page a (1,1)

INSTRUCTION MANUAL

VHF AIR BAND TRANSCEIVER

iA110EURO

IC-A110EURO-2 02.3.12 2:00 PM Page b (1,1) i

FOREWORD

READ ALL INSTRUCTIONS

carefully and completely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL

This instruction manual contains important operating instructions for the IC-A110EURO.

EXPLICIT DEFINITIONS

The explicit definitions below apply to this instruction manual.

WORD

RWARNING

DEFINITION

Personal injury, re hazard or electric shock may occur.

CAUTION

Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk of personal injury, re or electric shock.

Versions of the IC-A110EURO which display the

“CE” symbol on the serial number seal, comply with the essential requirements of the 89/336/EEC directive for Electromagnetic Compatibility.

CAUTIONS

R WARNING! NEVER

operate the transceiver with a headset or other audio accessories at high volume levels.

Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discontinue use.

NEVER

connect the transceiver to an AC outlet or to a power source of more than 32 V DC. Such a connection will damage the transceiver.

NEVER

connect the transceiver to a power source that is

DC fused at more than 5 A. Accidental reverse connection will be protected by this fuse, higher fuse values will not give any protection against such accidents and the transceiver will be ruined.

DO NOT

operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere.

DO NOT

connect the transceiver to a power source using reverse polarity. This connection will not only blow fuses but also may damage the transceiver.

IC-A110EURO-2 02.3.12 2:00 PM Page c (1,1)

DO NOT

place unit in a non-secure place to avoid inadvertent use by children.

DO NOT

push the PTT when not actually desiring to transmit.

AVOID

using or placing the transceiver in direct sunlight or in areas with temperatures below –30°C (–22°F) or above

+60°C (+140°F).

AVOID

placing the transceiver in excessively dusty environments.

AVOID

placing the transceiver against walls. This will obstruct heat dissipation.

AVOID

the use of chemical agents such as benzine or alcohol when cleaning, as they damage the transceiver surfaces.

BE CAREFUL!

The transceiver will become hot when operating continuously for long periods.

TABLE OF CONTENTS

FOREWORD ........................................................................................... i

EXPLICIT DEFINITIONS ......................................................................... i

CAUTIONS .............................................................................................. i

TABLE OF CONTENTS .......................................................................... ii

1 PANEL DESCRIPTION ............................................................... 1 – 3

■Panel description ............................................................................. 1–2

■Function display .................................................................................... 3

2 BASIC OPERATION ................................................................... 4 – 5

■Power ON ............................................................................................. 4

■Channel selection .................................................................................. 4

■Squelch function .................................................................................... 5

■Side tone function.................................................................................. 5

■LCD backlight control ............................................................................ 5

■Dial select function ................................................................................ 5

3 SCAN OPERATION ................................................................... 6 – 7

■Scan operation ..................................................................................... 6

■On-hook scan ....................................................................................... 7

■Dualwatch ............................................................................................. 7

4 MEMORY PROGRAMMING ...................................................... 8 – 9

■Programming a memory channel .......................................................... 8

■Memory names...................................................................................... 9

5 OTHER FUNCTIONS ............................................................... 10-11

■Initial set mode ............................................................................... 10-11

6 CONNECTION AND INSTALLATION .................................... 12 – 13

■Rear panel and connections ............................................................... 12

■Mounting ............................................................................................. 13

■Supplied accessories........................................................................... 13

7 CLONING ...................................................................................... 14

8 SPECIFICATIONS ............................................................. 15-17

9 OPC-871 HEADSET ADAPTER/OTHER OPTIONS.......... 18-19

■OPC-871 Headset adapter .................................................................. 18

■Other Options ...................................................................................... 19 ii

IC-A110EURO-2 02.3.12 2:00 PM Page d (1,1)

1

PANEL DESCRIPTION

Panel description

q w e r

1

V/M SCAN PRI SQL

!0

o i u qTUNING [DIAL(TS)]

➥Changes the operating frequency; memory channel in memory mode; set mode contents in set mode, etc.

➥Push to toggle the dimmer control OFF, Low and High.

➥Push and hold for 1 sec. to select the Tuning Step [TS];

1 MHz or 10 kHz are available. (p. 5) wFUNCTION DISPLAY (p. 3)

Displays the operating frequency, memory channel name, etc.

y t eVOLUME UP [Y] DOWN [Z] KEY

Adjusts the audio output level.

rLOUD SPEAKER

Front mounted loud speaker.

tPOWER SWITCH [POWER]

Push and hold 500 m sec. to turn the power ON and OFF.

➥The following functions are available at power ON as options:

• Initial set mode (p. 10)

• Cloning mode (p. 14)

IC-A110EURO-2 02.3.12 2:00 PM Page e (1,1) ySQL SWITCH [SQL]

➥Push to turn on the squelch adjust mode. (p. 6)

➥Push and hold this switch for 1 sec. to turn ON/OFF the both internal and external speaker output. (p. 4) uPRIORITY SWITCH [PRI]

➥Push to select priority channel. (p. 11)

• “Pr” appears on the display.

iSCAN SWITCH [SCAN]

➥Starts and stops the scan function:

• VFO mode: VFO scan function.

• Memory mode: Memory channel scan function. (p. 6)

➥ Push and hold this switch for 5 sec. to set the displayed channel as a memory lock-out channel. (p. 8)

• “LOCK OUT” appears on the display.

oVFO/MEMORY SWITCH [V/M]/[MW]

➥Push to toggle the VFO mode or the Memory mode. (p. 4)

• “X” and memory channel number appear when memory mode is selected.

• The transceiver has 20 memory channels.

➥When VFO mode is selected;

•Push and hold this switch for 5 sec. to program the VFO frequency to memory channel. (p. 8)

➥When Memory mode is selected;

Push and hold this switch for 5 sec. to turn the “Memory name write mode” ON.

PANEL DESCRIPTION

1

!0MICROPHONE CONNECTOR

Connects the supplied microphone or optional.

NEVER connect other microphones. The pin assignments may be different and the transceiver may be damaged.

MICROPHONE

The supplied microphone has a PTT switch and a cradle. The following functions are available when the microphone is taken off from the hook or put back on hook:

➥Automatic scan starts when putting on hook. (p. 7)

➥Automatic scan stops when taken off hook. (p. 7)

NOTE: Optional functions vary with transceiver version.

In this manual, optional functions are indicated by

” Icon.

Please contact your dealer for details.

2

IC-A110EURO-2 02.3.12 2:00 PM Page f (1,1)

3

1

PANEL DESCRIPTION

Function display

!1

q w e r t y o i u qMEMORY MODE INDICATOR (p. 5)

Appears when memory mode is selected.

wDUALWATCH INDICATOR (p. 7)

Indicates when the dualwatch function is activated.

eSCAN INDICATOR (p. 8)

Indicates when the scan function is selected.

rBUSY INDICATOR (p. 6)

“BUSY” appears when receiving a signal or when the squelch is open. (p. 6) t TX INDICATOR (p. 5)

Appears while transmitting.

y FREQUENCY DISPLAY (p. 11)

➥Shows the operating frequency.

➥Shows the channel name when the memory name function is selected. (p. 10) u VOLUME LEVEL INDICATORS

➥Shows the AF volume level(while receiving).

i SET MODE INDICATOR

➥Appears when the Initial set mode is selected. (p. 12)

!0 LOCK OUT INDICATOR

➥Appears when the channel is set as a ‘LOCK OUT’ channel. (p. 10)

!1 MEMORY CHANNEL INDICATOR

➥Indicates the selected memory channel number

➥‘Pr’ appears when the priority channel is selected.

*NOTE: The VFO/memory switch [V/M] and the memory write switch [M/W] functions may not be available depending on version.

IC-A110EURO-2 02.3.12 2:00 PM Page g (1,1)

Power ON

q Push [POWER] to turn power ON.

w Operate the transceiver as indicated in the following sections.

e Select the desired memory channel (or VFO frequency) with the [V/M] keys.

• When receiving a signal, appears and audio is emitted from the speaker.

• Further adjustment of audio level may be necessary at this point.

• Push [SQL] to adjust the squelch level. (p. 6)

• Push and hold the tuning dial for 1 sec. to select the [TS], each push increments/decrements to the frequency are either 10 kHz or 1 MHz. (p. 7) r Push and hold [PTT] to transmit, then speak into the microphone.

• Transmit indicator lights.

t Release [PTT] to receive.

BASIC OPERATION

2

Channel selection

ï VFO/Memory selection

q Push [V/M] to select memory mode or VFO mode.

➥Rotate the dial to select a desired frequency/channel.

w During memory mode operation, push [V/M] key to transfer the memory contents to

VFO.

mode.

NOTE: Only frequency data is transferred even if the memory channel has a memory name.

ï External speaker output control

External speaker output can be turned OFF, if desired.

q Push and hold [SQL] for 1 sec.

w Rotate the dial to select “SP OFF”.

e Push [SQL] to turn to the previous mode.

NOTE: This function available both internal and external speakers.

4

IC-A110EURO-2 02.3.12 2:00 PM Page h (1,1)

5

2

BASIC OPERATION

Squelch function

The transceiver has a noise squelch circuit to mute undesired noise while receiving no signal.

D Setting the squelch level

q Push [SQL] to turn the level adjusting mode ON.

w Turn the tuning [DIAL] to select the squelch level.

‘SQ 01’ is loose squelch and ‘SQ 25’ is tight squelch. (Initial level is ‘SQ 01’)

‘SQ 01’ indicates that the squelch circuit is turned off.

• “ ” appears on the display.

e Push [SQL] to return to regular operation.

Side tone function

When using an optional headset, such as those from the

David Clark Co. via the OPC-871

HEAD SET ADAPTOR

, the transceiver outputs your transmitted voice to the headset for monitoring. (p. 17)

LCD backlight control

The backlight of the can be set OFF, Low or High.

➥Push [DIAL] to toggle the backlight control; OFF, Low or

High are available.

Dial select function

Use the dial select function to adjust the tuning behaviour of the [DIAL] keys—use 1 MHz tuning when you want to change the frequency in large increments; use regular tuning (25 kHz or 8.33 kHz) when you want to change the frequency in smaller increments.

q Push [V/M] to select VFO mode.

w Push and hold [DIAL(TS)] for

1 sec. to select the desired tuning increment.

1 MHz tuning or regular tuning steps can be selected. (see diagrams at right) e Push and hold [DIAL(TS)] for

1 sec. to return to normal operation.

1 MHz tuning selected

Regular tuning selected

NOTE: Large tuning steps should be used only when you want to change the frequency in large increments. Please select regular tuning steps for normal operation.

IC-A110EURO-2 02.3.12 2:00 PM Page i (1,1)

SCAN OPERATION

Scan operation

q Push [V/M] to select memory mode or VFO mode, if necessary.

• “ ” appears on the memory mode.

w Make sure the squelch level is set to the threshold point.

• Set a squelch level (01 to 25) where the noise is muted.

e Push [SCAN] to start scan.

• To change the scan direction, turn [DIAL].

• “SCAN (or P SCAN)“ flashes while scanning.

r Push [SCAN] again to stop the scan.

NOTE: Normal scan or Priority scan is pre-programmed by cloning. Please ask your dealer or system operator for details.

ï PRIORITY SCAN

Priority memory scan

While scanning on a memory mode, priority watch checks for a signal on the selected priority channel every 250 m sec except lockout channel.

250 msec.

Priority ch

SKIP

250 msec.

Mch 1

Mch 2*

Mch 3

Mch 20

*: Lockout ch

3

VFO scan

Repeatedly scans all frequencies over the entire band. Scan step is minimum channel spacing. (e.g. 25 kHz or

8.33 kHz) lowest frequency

Start

Scan

Jump highest frequency

ï NORMAL SCAN

Memory lock scan

Repeatedly scans memory channels except skip (lockout) channels.

Mch 1

Mch 2*

Mch 3

SKIP

Mch 20

250 msec.

*: Lockout ch

6

IC-A110EURO-2 02.3.12 2:00 PM Page j (1,1)

3

SCAN OPERATION

On–hook scan

On–hook scan (Hanger scan) is available when taking the microphone from its hanger (off–hook) and /or returning it into the hanger (on–hook).

q Push [SCAN] to start scanning.

w When receiving a signal, scan pauses until the signal disappears.

➥You can converse by taking the microphone from the hook.

e Place the microphone on the hook to restart scanning.

r Scan restarts 2 sec. after the signal disappears even if you did not converse the station.

When you take the microphone during the scan operation.

➥In VFO scan; scan resumes promptly to frequency.

➥In memory scan; scan resumes promptly to memory channel.

➥In priority memory scan; scan resumes to priority channel,

NOTE: Be sure to connect the supplied microphone hanger to the vehicle’s ground for on/off hook microphone functions. (p. 12)

Dualwatch

Dualwatch monitors priority channel while you are receiving an other channel (VFO or memory channel).

• If a signal is received on priority channel, dualwatch pauses on priority channel until the signal disappears.

• To transmit on the selected channel during dualwatch, push and hold

PTT.

250 msec.

Priority channel

5 sec.

VFO frequency or memory

channel q Select the desired operating channel (VFO or Memory channel).

w Push and hold [PRI] for 1 sec. to start dualwatch.

‘P’ blinks during dualwatch.

e To cancel dualwatch, push [PRI] again.

7

IC-A110EURO-2 02.3.12 2:00 PM Page k (1,1)

Programming a memory

channel

The transceiver has 20 memory channels for storage of often

-used frequencies.

q Push [V/M] to select VFO mode, if necessary.

w Turns the [DIAL] to select the desired frequency.

• Push [DIAL/TS] one or more times to use the dial select function, if desired.

e Push [V/M] for 5 sec. to enter memory programming mode.

• “ ” and memory channel number appear.

r Turn the [DIAL] to select the desired memory channel number.

t Push [V/M] for 1 sec. to program the information into the channel and return to VFO mode.

• Push [SQL] for 1 sec. to clear the memory information.

MEMORY PROGRAMMING

4

D Setting lockout channels

In order to speed up the scan interval, you can set memory channels you don’t wish to be scanned as lockout channels.

q Push [V/M] to select memory mode, if necessary.

• “ ” appears.

w Turn the [DIAL] to select a memory channel to set as a lockout channel.

e Push [SCAN] for 5 sec. to toggle the lockout setting

ON/OFF.

• “LOCK OUT” appears when the channel is set as a lockout channel.

Memory channel 8 is set as lockout channel.

NOTE: The VFO/memory switch [V/M] and the memory write switch [M/W] functions may not be available depending on version.

8

IC-A110EURO-2 02.3.12 2:00 PM Page l (1,1)

4

MEMORY PROGRAMMING

Memory names

ï Programming memory names

q Select the memory channel to be programmed:

➥Push [V/M] to select memory mode.

➥Turns [DIAL] to select the memory channel.

w Push [V/M] for 5 sec. to enter memory name writing mode.

• The first character of the name flashes.

e Turns the [DIAL] as many times as necessary to enter the desired name.

• To erase a character, overwrite with a space (displayed as _).

• To move the cursor forwards or backwards, use [Y] or [Z].

• Push [SQL] for 2 sec. to erase all characters.

r Push [SCAN/MW] for 2 sec. to input the set name.

• Flashing stops.

• Memory channels can be programmed with names of up to 7 characters in length.

• When no name is programmed, the display shows the operating frequency.

[EXAMPLE]: Setting the name to “ TOWER 2”

V/M

for 5 sec.

+

NOTE: Push PTT switch to abort the programming memory name.

• The following characters can be used in names:

0 to 9, A to Z (capitals), (space), $, %, , (, ),

✽, +, “ ,

, , /, <, =, >, ?, @, [, \, ], ^, _ and `. or

V/M

for 1 sec.

9

IC-A110EURO-2 02.3.12 2:00 PM Page m (1,1)

OTHER FUNCTIONS

Initial set mode

Initial set mode is accessed at power ON and allows you to set seldom-changed settings. In this way you can “customize” transceiver operations to suit your preferences and operating style.

D Entering initial set mode

q While pushing and holding [V/M] + [TS(DIAL)], push

[POWER] sw to turn power ON.

• The transceiver enters initial set mode and “MN”, “BP”, “ST” or

“PR” (p. 11) appears on the display.

w Push [TS(DIAL)] to select the desired item as described below and at right.

e Turn [DIAL(TS)] to select the desired condition.

r Push [SCAN] to exit initial set mode and select the previous operating mode.

D Memory names

This item allows you to display a memory name instead of frequency.

• When a memory channel has not been programmed with a name, frequency indication appears instead.

D Beep tones ON/OFF

Confirmation beep tones normally sound when you push a key. These can be turned ON or

OFF as you prefer.

D Side tones ON/OFF

When using an optional headset such as those from the David

Clark Co. via the adapter, the transceiver outputs your transmitted voice to the headset for monitoring.

Optional

OPC-871 HEADSET

ADAPTER is required

.

5

10

IC-A110EURO-2 02.3.12 2:00 PM Page n (1,1)

5

OTHER FUNCTION

D Priority channel

The priority channel is used to store your most often-used channel for quick recall. In addition the priority channel is monitored during priority scan modes. The default setting for the priority channel will differ depending on pre-programming.

➥Push [PRI] to toggle the priority channel mode or previous mode.

Setting the priority channel

q While pushing and holding [V/M] and [DIAL(TS)], push

[POWER] to turn the power ON.

• The transceiver enters initial set mode.

w Push [TS(DIAL)] to select the priority channel set mode.

e Select the desired channel number as a priority channel or OFF with [DIAL].

r Push [POWER] to turn power OFF.

NEVER select the blank memory channel as the priority channel. In such case priority automatically sets to OFF position.

11

IC-A110EURO-2 02.3.12 2:00 PM Page o (1,1)

CONNECTION AND INSTALLATION

Rear panel and connections

Antenna

External speaker jack ⁄

¤

6 fi

OPC-871 HEADSET

ADAPTER (Option)

‹ q Connects to an antenna

Ask your dealer about antenna selection and best installation location. (Standard 50

Ω antenna with a SWR <3.0) w MICROPHONE HANGER

Connect the supplied microphone hanger to the vehicle’s ground for hanger scan function when hanging or releasing the microphone.

e DC POWER RECEPTACLE

Connects to a 12 or 24 V DC battery. Pay attention to pored: ,

Supplied DC power cable black: .

matic selectable.) larities.

• 12 V or 24 V automatic selectable.

r EXTERNAL SPEAKER JACK

Connect an 8

Ω,10 W (Max.) external speaker, if desired.

CAUTION : Be sure to use the external speaker’s power input rating more than 10 W, other wise the speaker damage may occur.

t OPC-871 OPTIONAL HEADSET ADAPTER

Connect an optional headset. (See p. 17)

12

IC-A110EURO-2 02.3.12 2:00 PM Page p (1,1)

13

6

CONNECTION AND INSTALLATION

Mounting

Flat washer

Spring washer

Supplied accessories

4

1

2

3

When using self-tapping screws

The universal mounting bracket supplied with your transceiver allows overhead or dashboard mounting. Please read the following instructions carefully.

• Mount the transceiver securely with the 4 supplied screws (M5

× 20) to a surface which is more than 10 mm thick and can support more than 5 kg.

• Mount the transceiver so that the face of the transceiver is at 90 ˚ to your line of sight when operating.

5

6

7

8

9

0

A

B q Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.

w Microphone hanger and screw set . . . . . . . . . . . . . . . . . . . .1 set e Microphone cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

r DC power cable (OPC-1091) . . . . . . . . . . . . . . . . . . . . . . . . . . .1

t Mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

y Bracket bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

u Mounting screws (M5

× 12) . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

i Self-tapping screws (M5

× 20) . . . . . . . . . . . . . . . . . . . . . . . . . .4

o Flat washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

!0 Spring washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

!1 Nuts

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

!2 Fuses (10 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IC-A110EURO-2 02.3.12 2:00 PM Page q (1,1)

D Data cloning

Cloning allows you to quickly and easily

] transfer the programmed contents from one transceiver to another transceiver, or, data from PC to a transceiver using the optional CS-A110EURO cloning software.

D Transceiver to transceiver cloning

q Connect the OPC-591

CLONING CABLE with adapter plugs to the [MIC] jack of the master and slave transceivers.

• The master transceiver is used to send data to the slave transceiver.

w While pushing and holding [Y] + [Z] + [V/M], push

[POWER] ON to enter cloning mode (master transceiver only—power ON only for slave transceiver).

• “CLONE” appears and the transceivers enter the clone standby condition.

e Push [POWER] on the master transceiver.

• “CL-OUT” appears in the master transceiver’s display.

• “CL-IN” appears automatically in the slave transceiver’s display.

e When cloning is finished, turn power OFF, then ON again to exit cloning mode.

CLONING

7

D Cloning using PC

Data can be cloned to and from a PC (IBM compatible) using the optional CS-A110EURO

CLONING SOFTWARE and the optional

OPC-478

CLONING CABLE

+ OPC-592

CLONING CABLE ADAPTER

. Consult the CS-A110EURO

CLONING SOFTWARE

HELP message for details.

D Cloning error

When the display at right appears, a cloning error has occurred.

• In this case, both transceivers automatically return to the clone standby condition and cloning must be repeated.

14

IC-A110EURO-2 02.3.12 2:00 PM Page r (1,1)

15

8

SPECIFICATIONS

D General

• Frequency coverage

• Channel spacing

: 118.000 to 136.975 MHz

: 25/8.33 kHz

• Number of memory channels : 20

• Acceptable power supply : 13.75* V or 27.5* V DC

(negative ground) (*Automatic selectable)

• Usable temp. range

• Frequency err

: –20 to +55˚C

: ±1 ppm (0 to +40˚C)

• Current drain

(at 13.75 V DC)

:

Tx 5 A (at max. power)

Rx 4 A ( at max. AF)

0.5 A (at stand by)

• Antenna impedance : Standard 50

Ω with SWR<3:1

• Dimensions :

(projections not incl.)

• Weight : 1.5 Kg

D Transmitter

• Output power : 9 W ±1.5dB (+15 to +35˚C)

9 W +2dB, –3dB (–20 to +55˚C)

• Modulation depth : More than 85%

• Modulation compression : Linear: 85%, Max. : 95%

• Amplitude modulation distortion : Less than 10 %

• Audio frequency response : +2 dB to –4 dB from

350 to 2500 Hz

More than –25 dB at 5000 Hz

(at 25 KHz channel spacing)

More than –25 dB at 3200 Hz

(at 8.33 KHz channel spacing)

• Adjacent channel power : Less than 60 dB

(at 25 KHz channel spacing)

Less than 50 dB

(at 8.33 KHz channel spacing)

• Conducted spurious emissions : Less than –46dBm

(9kHz to 30 MHz)

Less than –36 dBm for harmonics

Less than –46 dBm for nonharmonics (30 MHz to 1 GHz)

Less than –30 dBm for harmonics

Less than –40 dBm for nonharmonics (1 GHz to 4 GHz)

IC-A110EURO-2 02.3.12 2:00 PM Page s (1,1)

D Receiver

• Receive system : Double conversion superheterodyne

• Intermediate frequencies : 1st 38.85 MHz

2nd 450 kHz

•Sensitivity (at 12 dB SINAD): Less than 5 dBµV

•Threshold squelch sensitivity: Less than –6 dBµV

•Harmonic distortion : Less than 5 % (at mod. 30%)

Less than 10 % (at mod. 90%)

• Audio frequency response : +2 dB to –4 dB from

350 to 3000 Hz

(at 25 KHz channel spacing)

+2 dB to –4 dB from

350 to 2500 Hz

(at 8.33 KHz channel spacing)

• Audio noise : More than 40 dB

• Adjacent channel rejection : More than 60 dB

• Spurious response rejection : More than 70 dB

• Intermodulation response rejection : More than 64 dB

• Blocking or desensitisation

•Conducted spurious emissions

: More than 70 dB

: Less than –57 dBm

(9 KHz to 1 GHz)

Less than –47 dBm

(1 GHz to 4 GHz)

• Cross modulation rejection : More than 70 dB

• Receiver dynamic range : Less than 6 dB

SPECIFICATIONS (VFO CHANNEL ID LIST)

8

• Audio output power

Side tone

: More than 10 W (at 13.75 V DC with 8

Ω load 60 % MOD. 10% distortion)

More than 100 mW (with 500

Ω load 60% MOD. 10 % distortion)

• Audio output impedance : Ext. SP 8

Side tone 500

All stated specifications are subject to change without notice or obligation.

16

IC-A110EURO-2 02.3.12 2:00 PM Page t (1,1)

17

8

SPECIFICATIONS (VFO CHANNEL ID LIST)

Channel spacing: 25 kHz (Actual frequency is displayed.)

Operating Freq.

Channel spacing

(MHz) (kHz)

118.0000

118.0250

118.0500

118.0750

118.1000

etc

25

25

25

25

25

Channel ID

(Displayed Freq.)

118.000

118.025

118.050

118.075

118.100

Channel spacing: 8.33 kHz

118.0000

118.0083

118.0167

118.0250

118.0333

118.0417

118.0500

118.0583

118.0667

118.0750

118.0833

118.0917

118.1000

etc

Operating Freq.

Channel spacing

(MHz) (kHz)

8.33

8.33

8.33

8.33

8.33

8.33

8.33

8.33

8.33

8.33

8.33

8.33

8.33

Channel ID

(Displayed Freq.)

118.005

118.010

118.015

118.030

118.035

118.040

118.055

118.060

118.065

118.080

118.085

118.090

118.105

Channel spacing: 8.33/ 25 kHz auto selection mode

Operating Freq.

Channel spacing

(MHz) (kHz)

118.0000

118.0000

118.0083

118.0167

118.0250

118.0250

118.0333

118.0417

118.0500

118.0500

118.0583

118.0667

118.0750

118.0750

118.0833

118.0917

118.1000

118.1000

etc

8.33

8.33

25

8.33

8.33

8.33

25

8.33

25

8.33

8.33

8.33

25

8.33

8.33

8.33

25

8.33

Channel ID

(Displayed Freq.)

118.000

118.005

118.010

118.015

118.025

118.030

118.035

118.040

118.050

118.055

118.060

118.065

118.075

118.080

118.085

118.090

118.100

118.105

IC-A110EURO-2 02.3.12 2:00 PM Page u (1,1)

OPC-871 HEADSET ADAPTER/OTHER OPTIONS

9

OPC-871 Headset adapter

When using an optional headset, such as those from the

David Clark Co. via the adapter

, the transceiver outputs your transmitted voice to the headset for monitoring. (pgs. 5, 10)

D Connection

PTT switch

Use a PTT switch with a 3.5

mm diameter plug, if required.

The optional OPC-871 HEADSET ADAPTER install as follows.

q Turns the power OFF, then disconnect the DC power cable.

wUnscrew the 4 screws, then remove the bottom cover. (Fig. 1) e Insert the connector as shown below. (Fig. 2) r Mount the phone plug attachment together with the mobile mounting bracket with 2 supplied screws. (Fig. 3)

Fig. 1

HEADSET

(Must be purchased separately.)

18

IC-A110EURO-2 02.3.12 2:00 PM Page v (1,1)

19

9

OPC-871/OPTIONS

• Bent the plastic dust cover before install the strain relief into the notch.

Fig. 2

• Use the upper side mounting hole.

• You can mount the attachment on either side of the transceiver.

Other options

OPC-871

HEADSET ADAPTER (See pgs. 18-19)

CS-A110EURO

CLONING SOFTWARE

Provides quick and easy programming of items, including private channels, scan settings, etc., via an IBM

® compatible PC

(Microsoft

®

Windows

®

95/98) to transceiver.

OPC-478

CLONING CABLE

OPC-592

CLONING CABLE ADAPTOR

These three components work as one set and provide a quick and easy programming of items, including memory channels, memory names and set mode contents, etc. via a PC.

OPC-591

CLONING CABLE

Cloning cable for transceiver to transceiver. Very convenient when programming cloning process. Allows transfer of programmed contents from one transceiver to another.

Fig. 3

IBM® is a registered trademark of International Business Machines.

Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S.A. and other countries.

IC-A110EURO-2 02.3.12 2:00 PM Page w (1,1)

OPTIONS

10

IC-A110EURO-2 02.3.12 2:00 PM Page x (1,1)

A-5619H-1EU-w

Printed in Japan

© 2001 Icom Inc.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement