Seagate | 9 - U Series CE 9 | Product manual | Seagate 9 - U Series CE 9 Product manual

Seagate 9 - U Series CE 9 Product manual
Product Manual
DB35 Series 7200.2
ST3500841ACE
ST3400833ACE
ST3300822ACE
ST3250824ACE
ST3200827ACE
ST3160212ACE
ST3120213ACE
ST3802110ACE
100389999
Rev. D
August 2007
Copyright © 2005-2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A.
Publication number: 100389999, Rev. D
August 2007
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC
in the United States and/or other countries. DB35 Series, SeaTools and SeaTDD are either trademarks or
registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States
and/or other countries. All other trademarks or registered trademarks are the property of their respective
owners.
One gigabyte, or GB, equals one billion bytes when referring to hard drive capacity. Accessible capacity
may vary depending on operating environment and formatting. Seagate reserves the right to change, without notice, product offerings or specifications.
Contents
1.0
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.0
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1
Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2.1
LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.6
Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7
Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.8
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.8.1
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.8.2
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8.3
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8.4
Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.9
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9.1
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9.2
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9.3
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9.4
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9.5
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9.6
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.10
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.11
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.12
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.13
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.13.1
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.13.2
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.13.3
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.14
Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.14.1
European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 20
2.15
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.0
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Breather filter hole precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1
Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2
Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3
Alternate capacity jumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.4
Ultra ATA/100 cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
23
24
25
25
25
25
26
26
4.0
ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.2
Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.3
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.4
S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
29
30
33
36
37
5.0
Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DB35 Series 7200.2 Product Manual, Rev. D
i
ii
DB35 Series 7200.2 Product Manual, Rev. D
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O pins and supported ATA signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DB35 Series 7200.2 Product Manual, Rev. D
14
14
24
25
26
27
29
iii
iv
DB35 Series 7200.2 Product Manual, Rev. D
1.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate® DB35
Series 7200.2 model drives:
• ST3500841ACE
• ST3400833ACE
• ST3300822ACE
• ST3250824ACE
• ST3200827ACE
• ST3160212ACE
• ST3120213ACE
• ST3802110ACE
These drives provide the following key features:
• Minimal acoustics for consumer storage usage profile.
• Bedroom quiet performance.
• Optimized power for consumer storage devices.
• Spinup current limited to a maximum of 2 amps.
• 7,200-RPM spindle speed
• 8-Mbyte buffer: ST3500841ACE, ST3400833ACE, ST3300822ACE, ST3250824ACE, and ST3200827ACE.
• 2-Mbyte buffer: ST3160212ACE, ST3120213ACE, and ST3802110ACE.
• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.
• Tunneling Magnetoresistive (TMR) recording heads.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Full-track multiple-sector transfer capability without local processor intervention.
• 350 Gs nonoperating shock.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Support for Read Multiple and Write Multiple commands.
• Support for autodetection of master/slave drives that use cable select (CSEL).
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• The 3D Defense System™, which includes Drive Defense, Data Defense, and Diagnostic Defense, offers
the industry’s most comprehensive protection for disc drives.
DB35 Series 7200.2 Product Manual, Rev. D
1
2
DB35 Series 7200.2 Product Manual, Rev. D
2.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the
following models:
ST3500841ACE
ST3250824ACE
ST3120213ACE
ST3400833ACE
ST3200827ACE
ST3802110ACE
ST3300822ACE
ST3160212ACE
2.1
Specification summary table
The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.
DB35 Series 7200.2 Product Manual, Rev. D
3
Table 1:
Drive specifications for 500 and 400 Gbyte models
Drive specification
ST3500841ACE
ST3400833ACE
Formatted Gbytes (512 bytes/sector)*
500
400
Guaranteed sectors
976,773,168
781,422,768
Bytes per sector
512
Default sectors per track
63
Default read/write heads
16
Default cylinders
16,383
Recording density, KBPI (kbits/in max)
790.1
Track density, KTPI (ktracks/in max)
124.5
2
4
Areal density, (Gbits/in max)
97.96
Spindle speed (RPM)
7,200
Internal data transfer rate (Mbits/sec max)
815.2
Sustained data transfer rate (Mbytes/sec max)
65.0
I/O data-transfer rate (Mbytes/sec max)
100
ATA data-transfer modes supported
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–5
Cache buffer
8 Mbytes
Height (mm max)
26.1 mm (1.028 inches)
Width (mm max)
101.6 mm (4.000 inches) +/- 0.010 inches
Length (mm max)
146.99 mm (5.787 inches)
Weight (typical)
710 grams (1.57 lb.)
Average latency (msec)
4.16
Power-on to ready (sec max)
16 sec
Standby to ready (sec max)
16 sec
Track-to-track seek time (msec typical)
<0.8 (read), <1.0 (write)
Average seek (msec typical)
18 (read), 20 (write)
Startup current (typical) 12V (peak)
2.0 amps
Seek power (typical)
12.60 watts
Operating (Consumer Storage Profile)
9.20 watts
Operating (PVR Storage Profile
4.88 watts
Idle mode (typical)
8.00 watts
Standby mode (typical)
0.80 watts
Sleep mode (typical)
0.80 watts
Voltage tolerance (including noise)
5V ± 5%
12V ± 10%
Ambient temperature
0° to 60°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient (°C per hour max)
20°C (operating)
30°C (nonoperating)
Relative humidity
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature (°C max)
37.7 (operating)
40.0 (nonoperating)
Altitude, operating
–60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating (below mean sea level, max)
–60.96 m to 12,192 m
(–200 ft. to 40,000+ ft.)
DB35 Series 7200.2 Product Manual, Rev. D
Drive specification
ST3500841ACE
Operational Shock (max at 2 msec)
63 Gs
Non-Operational Shock (max at 2 msec)
300 Gs
Vibration, operating
5-22 Hz: +/-0.25”, Displacement limited
22-350 Hz: 0.5 Gs
350-500 Hz: 0.25 Gs
Vibration, nonoperating
5-22 Hz: +/-0.25”, Displacement limited
22-350 Hz: 5.0 Gs
350-500 Hz: 1.0 Gs
ST3400833ACE
Drive acoustics, sound power
Idle** (bels)
2.79 (typical)
2.96 (max)
2.59 (typical)
2.75 (max)
Operational, CE seeks (bels)
2.82 (typical)
2.97 (max)
2.75 (typical)
2.90 (max)
Operational, PVR seeks (bels)
2.71 (typical)
2.88 (max)
2.61 (typical)
2.75 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
0.70%
Warranty
5 years on distribution units.
To determine the warranty for a specific drive, use a web browser to access
the following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to
provide the drive serial number, model number (or part number) and country
of purchase. The system will display the warranty information for your drive.
Contact start-stop cycles (25°C, 50% rel. humidity)
50,000
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
DB35 Series 7200.2 Product Manual, Rev. D
5
Table 2:
Drive specifications for 300, 250, and 200 Gbyte models
Drive specification
ST3300822ACE
ST3250824ACE
ST3200827ACE
Formatted Gbytes (512 bytes/sector)*
300
250
200
Guaranteed sectors
586,072,368
488,397,168
390,721,968
Bytes per sector
512
Default sectors per track
63
Default read/write heads
16
Default cylinders
16,383
Recording density, KBPI (kbits/in max)
790.1
Track density, KTPI (ktracks/in max)
124.5
2
6
Areal density, (Gbits/in max)
97.69
Spindle speed (RPM)
7,200
Internal data transfer rate (Mbits/sec max)
867.2
Sustained data transfer rate (Mbytes/sec max)
76.6
I/O data-transfer rate (Mbytes/sec max)
100
ATA data-transfer modes supported
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–5
Cache buffer
8 Mbytes
Height (mm max)
26.1 mm (1.028 inches)
Width (mm max)
101.6 mm (4.000 inches) +/- 0.010 inches
Length (mm max)
146.99 mm (5.787 inches)
Weight (typical)
655 grams (1.44 lb.)
Average latency (msec)
4.16
Power-on to ready (sec max)
16 sec
Standby to ready (sec max)
16 sec
Track-to-track seek time (msec typical)
<0.8 (read), <1.0 (write)
Average seek (msec typical)
18 (read), 20 (write)
Startup current (typical) 12V (peak)
2.0 amps
Seek power (typical)
12.40 watts
Operating (Consumer Storage Profile)
9.25 watts
Operating (PVR Storage Profile
4.88 watts
Idle mode (typical)
8.00 watts
Standby mode (typical)
0.80 watts
Sleep mode (typical)
0.80 watts
Voltage tolerance (including noise)
5V ± 5%
12V ± 10%
Ambient temperature
0° to 60°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient (°C per hour max)
20°C (operating)
30°C (nonoperating)
Relative humidity
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature (°C max)
37.7 (operating)
40 (nonoperating)
Altitude, operating
–60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating (below mean sea level, max)
–60.96 m to 12,192 m
(–200 ft. to 40,000+ ft.)
580 grams (1.28 lb.)
DB35 Series 7200.2 Product Manual, Rev. D
Drive specification
ST3300822ACE
ST3250824ACE
Operational Shock (max at 2 msec)
63 Gs
Non-Operational Shock (max at 2 msec)
350 Gs
Vibration, operating
5-22 Hz: 0.25 Gs, Limited displacement
22-350 Hz: 0.5 Gs
350-500 Hz: 0.25 Gs
Vibration, nonoperating
5–22 Hz: 0.25 Gs, Limited displacement
22-350 Hz: 5.0 Gs
350-500 Hz: 1.0 Gs
ST3200827ACE
Drive acoustics, sound power
Idle* (bels)
2.67 (typical)
2.82 (max)
Operational, CE seeks (bels)
2.80 (typical)
2.90 (max)
Operational, PVR seeks (bels)
2.68 (typical
2.80 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
0.70%
Warranty
5 years on distribution units.
To determine the warranty for a specific drive, use a web browser to access
the following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to
provide the drive serial number, model number (or part number) and country
of purchase. The system will display the warranty information for your drive.
Contact start-stop cycles (25°C, 50% rel. humidity)
50,000
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
DB35 Series 7200.2 Product Manual, Rev. D
7
Table 3:
Drive specifications for 160, 120, and 80 Gbyte models
Drive specification
ST3160212ACE
ST3120213ACE
ST3802110ACE
Formatted Gbytes (512 bytes/sector)*
160
120
80
Guaranteed sectors
312,581,808
234,441,648
156,301,488
Bytes per sector
512
Default sectors per track
63
Default read/write heads
16
Default cylinders
16,383
Recording density, KBPI (kbits/in max)
840.0
Track density, KTPI (ktracks/in max)
141.5
2
8
Areal density, (Gbits/in max)
119.0
Spindle speed (RPM)
7,200
Internal data transfer rate (Mbits/sec max)
867.2
Sustained data transfer rate (Mbytes/sec max)
83.0
I/O data-transfer rate (Mbytes/sec max)
100
ATA data-transfer modes supported
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–5
Cache buffer
2 Mbytes
Height (mm max)
26.1 mm (1.028 inches)
Width (mm max)
101.6 mm (4.000 inches) +/- 0.010 inches
Length (mm max)
146.99 mm (5.787 inches)
Weight (typical)
580 grams (1.28 lb.)
Average latency (msec)
4.16
Power-on to ready (sec max)
16 sec
Standby to ready (sec max)
16 sec
Track-to-track seek time (msec typical)
<0.8 (read), <1.0 (write)
Average seek (msec typical)
18 (read), 20 (write)
Startup current (typical) 12V (peak)
2.0 amps
Seek power (typical)
12.40 watts
Operating (Consumer Storage Profile)
9.25 watts
Operating (PVR Storage Profile
4.91 watts
Idle mode (typical)
8.00 watts
Standby mode (typical)
0.80 watts
Sleep mode (typical)
0.80 watts
Voltage tolerance (including noise)
5V ± 5%
12V ± 10%
Ambient temperature
0° to 60°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient (°C per hour max)
20°C (operating)
30°C (nonoperating)
Relative humidity
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature (°C max)
37.7 (operating)
40 (nonoperating)
Altitude, operating
–60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating (below mean sea level, max)
–60.96 m to 12,192 m
(–200 ft. to 40,000+ ft.)
DB35 Series 7200.2 Product Manual, Rev. D
Drive specification
ST3160212ACE
ST3120213ACE
Operational Shock (max at 2 msec)
63 Gs
Non-Operational Shock (max at 2 msec)
350 Gs
Vibration, operating
5-22 Hz: +/-0.25”, Displacement limited
22-350 Hz: 0.5 Gs
350-500 Hz: 0.25 Gs
Vibration, nonoperating
5-22 Hz: +/-0.25”, Displacement limited
22-350 Hz: 5.0 Gs
350-500 Hz: 1.0 Gs
ST3802110ACE
Drive acoustics, sound power
Idle** (bels)
2.48 (typical)
2.64 (max)
2.46 (typical
2.65 (max)
2.43 (typical
2.51 (max)
Operational, CE seeks (bels)
2.65 (typical)
2.95 (max)
2.57 (typical
2.64 (max)
2.61 (typical)
2.63 (max)
Operational, PVR seeks (bels)
2.53 (typical)
2.62 (max)
2.50 (typical
2.57 (max)
2.45 (typical)
2.51 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
0.70%
Warranty
5 years on distribution units.
To determine the warranty for a specific drive, use a web browser to
access the following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked
to provide the drive serial number, model number (or part number) and
country of purchase. The system will display the warranty information for
your drive.
Contact start-stop cycles (25°C, 50% rel. humidity)
50,000
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
DB35 Series 7200.2 Product Manual, Rev. D
9
2.2
Formatted capacity
Model
Formatted
capacity*
Guaranteed
sectors
Bytes per sector
ST3500841ACE
500 Gbytes
976,773,168
512
ST3400833ACE
400 Gbytes
781,422,768
512
ST3300822ACE
300 Gbytes
586,072,368
512
ST3250824ACE
250 Gbytes
488,397,168
512
ST3200827ACE
200 Gbytes
390,721,968
512
ST3160212ACE
160 Gbytes
312,581,808
512
ST3120213ACE
120 Gbytes
234,441,648
512
ST3802110ACE
80 Gbytes
156,301,488
512
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
2.2.1
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
See Section 4.1.2, "Identify Device command" (words 60-61 and 100-103) for additional information about 48bit addressing support of drives with capacities over 137 Gbytes.
2.3
Default logical geometry
Cylinders
Read/write heads
Sectors per track
16,383
16
63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
2.4
Recording and interface technology
Interface
ATA
Recording method
16/17 EPRML
Recording density KBPI (kbits/inch max)
ST3500841ACE, ST3400833ACE, ST3300822ACE,
ST3250824ACE, ST3200827ACE
790.1
ST3160212ACE, ST3120213ACE, ST3802110ACE
840.0
Track density KTPI (ktracks/inch max)
ST3500841ACE, ST3400833ACE, ST3300822ACE,
ST3250824ACE, ST3200827ACE
124.5
ST3160212ACE, ST3120213ACE, ST3802110ACE
141.5
Areal density
10
(Gbits/inch2
max)
DB35 Series 7200.2 Product Manual, Rev. D
ST3500841ACE, ST3400833ACE, ST3300822ACE,
ST3250824ACE, ST3200827ACE
97.69
ST3160212ACE, ST3120213ACE, ST3802110ACE
119.0
Spindle speed (RPM) (± 0.2%)
7,200
Internal data-transfer rate (Mbits/sec max)
ST3500841ACE, ST3400833ACE
815.2
ST3300822ACE, ST3250824ACE, ST3200827ACE,
ST3160212ACE, ST3120213ACE, ST3802110ACE
867.2
Sustained data transfer rate (Mbytes/sec max)
ST3500841ACE, ST3400833ACE
65.0
ST3300822ACE, ST3250824ACE, ST3200827ACE
76.6
ST3160212ACE, ST3120213ACE, ST3802110ACE
83.0
I/O data-transfer rate (Mbytes/sec max)
100 (Ultra DMA mode 5)
Cache buffer
ST3500841ACE, ST3400833ACE, ST3300822ACE,
ST3250824ACE, ST3200827ACE
ST3160212ACE, ST3120213ACE, ST3802110ACE
DB35 Series 7200.2 Product Manual, Rev. D
8 Mbytes (8,192 kbytes)
2 Mbytes (2,048 kbytes)
11
2.5
Physical characteristics
Drive specification
Maximum height
(mm)
(inches)
26.1
1.028
(mm)
(inches)
101.6
4.000 ± 0.010
(mm)
(inches)
146.99
5.787
Maximum width
Maximum length
Typical weight
2.6
ST3500841ACE
ST3400833ACE
710 grams (1.57 lbs)
ST3300822ACE
655 grams (1.44 lbs)
ST3250824ACE
ST3200827ACE
ST3160212ACE
ST3120213ACE
ST3802110ACE
580 grams (1.28 lbs)
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between
random tracks, less overhead.
Typical seek times (msec)
Read
Write
Track-to-track
0.8
1.0
Average
18
20
Average latency:
4.16
4.16
Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,
regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.
However, due to the manner in which these drives are formatted, benchmark tests that include command
overhead or measure logical seeks may produce results that vary from these specifications.
2.7
Start/stop times
Power-on to Ready (sec)
16
Standby to Ready (sec)
16 (max)
Ready to spindle stop (sec)
10 (max)
12
DB35 Series 7200.2 Product Manual, Rev. D
2.8
Power specifications
The drive receives DC power (+5V and +12V) through a four-pin standard drive power connector.
2.8.1
Power consumption
Power requirements for the drives are listed in the table on page 13. Typical power measurements are based
on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambient temperature.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power represents the worstcase power consumption, using only random seeks with read or write latency time. This mode is not typical
and is provided for worst-case information.
• Operating power and current
Operating power is measured using a standard Consumer Storage Profile.
• Idle mode power
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in
a random track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down mode.
Table 4:
DC power requirements
5V typ
amps
12V typ
amps
—
—
2.0 (peak)
All
8.00
0.353
0.519
500GB, 400GB
9.20
300GB, 250GB, 200GB,
160GB, 120GB and 80GB
0.587
0.520
9.25
500GB, 400GB, 300GB,
250GB and 200GB
4.88
0.39
0.41
160GB, 120GB and 80GB
4.91
500GB, 400GB
12.60
300GB, 250GB, 200GB,
160GB, 120GB and 80GB
0.613
0.795
12.40
Standby
All
0.80
0.106
0.023
Sleep
All
0.80
0.106
0.023
Power dissipation (watts)
Models
Spinup
All
Idle
Operating (Consumer Storage Profile)
Operating (PVR Storage Profile)
Seeking
DB35 Series 7200.2 Product Manual, Rev. D
Average
(watts, 25° C)
13
2.8.1.1
Typical current profile
Figure 1
Typical 5V startup and operation current profile
Figure 2
Typical 12V startup and operation current profile
2.8.2
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on
the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.
• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write
current.
2.8.3
Voltage tolerance
Voltage tolerance (including noise):
5V ± 5%
12V ± 10%
14
DB35 Series 7200.2 Product Manual, Rev. D
2.8.4
Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems,
you can control power management through the system setup program. The drive features the following
power-management modes:
Power mode
Heads
Spindle
Buffer
Active
Tracking
Rotating
Enabled
Idle
Tracking
Rotating
Enabled
Standby
Parked
Stopped
Enabled
Sleep
Parked
Stopped
Disabled
• Active mode
The drive is in Active mode during the read/write and seek operations.
• Idle mode
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc
access is necessary.
• Standby mode
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the
standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a
specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby
mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all
commands and returns to Active mode any time disc access is necessary.
• Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer
is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a
Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby
mode with all current translation parameters intact.
• Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive
activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive
accepts all commands and returns to Active mode when disc access is necessary.
DB35 Series 7200.2 Product Manual, Rev. D
15
2.9
Environmental specifications
2.9.1
Ambient temperature
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions for
standard models. Recommended measurement locations are shown in See Figure 6 on page 27.
Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 44°C (112°F) at 10,000 feet
(3,048 meters).
Operating:
0° to 60°C (32° to 140°F)
Nonoperating:
–40° to 70°C (–40° to 158°F)
2.9.2
Temperature gradient
Operating:
20°C per hour (68°F per hour max), without condensation
Nonoperating:
30°C per hour (86°F per hour max)
2.9.3
Humidity
2.9.3.1
Relative humidity
Operating:
5% to 90% noncondensing (30% per hour max)
Nonoperating:
5% to 95% noncondensing (30% per hour max)
2.9.3.2
Wet bulb temperature
Operating:
37.7°C (99.9°F max)
Nonoperating:
40°C (104°F max)
2.9.4
Altitude
Operating:
–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)
Nonoperating:
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)
2.9.5
Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive
mounting screws. Shock may be applied in the X, Y or Z axis.
2.9.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum
operating shock of 63 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more
than two times per second.
16
DB35 Series 7200.2 Product Manual, Rev. D
2.9.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 300 Gs for 500, 400, and 300 GB drives and 350 Gs
for 250, 200, 160, ad 80 GB drives, based on a nonrepetitive half-sine shock pulse of 2 msec duration.
2.9.6
Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the
drive mounting screws. Vibration may be applied in the X, Y or Z axis.
2.9.6.1
Operating vibration
The following table lists the maximum vibration levels that the drive may experience while meeting the performance standards specified in this document.
5–22 Hz
+/-0.25”, Displacement limited
22–350 Hz
0.50 Gs
350–500 Hz
0.25 Gs
2.9.6.2
Nonoperating vibration
The following table lists the maximum nonoperating vibration that the drive may experience without incurring
physical damage or degradation in performance when subsequently put into operation.
5–22 Hz
0.25 Gs (Limited displacement)
22–350 Hz
5.0 Gs
350–500 Hz
1.0 Gs
2.10
Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.
Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined
by the following equation:
(Number of seeks per second = 0.4 / (average latency + average access time)
Drive acoustics, sound power
Idle
Operational, CE seeks
Operational, PVR (Personal Video Recorder) seeks
2.46 bels (typ)
2.65 bels (max)
2.57 bels (typ)
2.64 bels (max)
2.50 bels (typ)
2.57 bels (max)
DB35 Series 7200.2 Product Manual, Rev. D
17
2.11
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the radio frequency (RF) environments defined in the following table:
Table 5:
Radio frequency environments
Performance
level
Reference
standard
Contact, HCP, VCP: ± 4 kV; Air:
± 8 kV
B
EN 61000-4-2: 95
Radiated RF immunity
80 to 1,000 MHz, 3 V/m,
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse
modulation @ 200 Hz
A
EN 61000-4-3: 96
ENV 50204: 95
Electrical fast transient
± 1 kV on AC mains, ± 0.5 kV on
external I/O
B
EN 61000-4-4: 95
Surge immunity
± 1 kV differential, ± 2 kV common, AC mains
B
EN 61000-4-5: 95
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms,
80% AM with 1 kHz sine
A
EN 61000-4-6: 97
Voltage dips, interrupts
0% open, 5 seconds
0% short, 5 seconds
40%, 0.10 seconds
70%, 0.01 seconds
C
C
C
B
EN 61000-4-11: 94
Test
Description
Electrostatic discharge
2.12
Reliability
Nonrecoverable read errors
1 per 1014 bits read, max.
Annualized Failure Rate (AFR)
0.70% (nominal power, 25°C ambient temperature)
Contact start-stop cycles
50,000 cycles
(at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle)
Preventive maintenance
None required
18
DB35 Series 7200.2 Product Manual, Rev. D
2.13
Agency certification
2.13.1
Safety certification
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections
of IEC950 and EN 60950 as tested by TUV North America.
2.13.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and
the immunity levels are defined by EN 55024.
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators
should confirm EMC compliance and provide CE marking for their products.
Korean RRL
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information
and Communication Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.
• EUT name (model numbers): See table below.
• Certificate numbers:
Model
Certificate Number
ST3500841ACE
E-H011-05-3453 (B)
ST3400833ACE
E-H011-05-3453 (B)
ST3300822ACE
E-H011-05-3453 (B)
ST3250824ACE
E-H011-05-3453 (B)
ST3200827ACE
E-H011-05-3453 (B)
ST3160212ACE
E-H011-05-3453 (B)
ST3120213ACE
E-H011-05-3453 (B)
ST3802110ACE
E-H011-05-3453 (B)
• Trade name or applicant: Seagate Technology
• Manufacturing date: January 2006
• Manufacturer/nationality: Singapore and China
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
DB35 Series 7200.2 Product Manual, Rev. D
19
2.13.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
2.14
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances.
2.14.1
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical
substances, including Lead (Pb), in electronic products effective July 2006.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the
rep-resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion
of any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard
operat-ing procedures that ensure that restricted substances are not utilized in our manufacturing operations,
labora-tory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
20
DB35 Series 7200.2 Product Manual, Rev. D
2.15
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment. Users
should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive
chemicals as electronic drive component reliability can be affected by the installation environment. The silver,
copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
DB35 Series 7200.2 Product Manual, Rev. D
21
22
DB35 Series 7200.2 Product Manual, Rev. D
3.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
Handling and static discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation.
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the
entire installation procedure.
• Handle the drive by its edges or frame only.
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
DB35 Series 7200.2 Product Manual, Rev. D
23
3.2
Breather filter hole precautions
This section contains information regarding the precautions which should be taken regarding the breather filter
hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent
possible damage to the drive.
Breather hole
Do not cover or seal
this hole.
Figure 3
Breather filter hole location
Caution: Do not cover, seal, or insert any object into this hole.
This hole has two purposes:
• To allow condensation inside the hard disc to escape
• To allow air pressure inside the hard disc to equalize with ambient pressure
Note.
24
If this hole is covered, sealed, or penetrated by any object, drive reliability may be compromised
and could lead to permanent damage—doing so voids the warranty.
DB35 Series 7200.2 Product Manual, Rev. D
3.3
Jumper settings
3.3.1
Master/slave configuration
The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual
header between the interface connector and the power connector. Use the following settings to configure the
drive as a master or a slave.
Master or single drive. The drive is configured at the factory for a master or single-drive operation with a
jumper set on pins 7 and 8.
Drive as slave. Remove all jumpers.
Drive as master with a non-ATA-compatible slave.
Use this jumper setting only if the drive does not work as a master with no jumpers installed.
Options jumper block
Master or single drive
Drive is slave
Master with non ATAcompatible slave
Cable select
Limit drive capacity
to 32 Gbytes
7 5 3 1
8 6 4 2
Circuit Board
Figure 4
Master/slave jumper settings
3.3.2
Cable-select option
Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,
CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To
enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to
determine whether your computer supports this option.
3.3.3
Alternate capacity jumper
Some older computers may “hang” at startup if their BIOS detects a disc drive with a capacity greater than 32
Gbytes. This limits the drive’s capacity to 32 Gbytes when the alternate capacity jumper is used. To access the
full capacity of the drive, you can:
• Update the BIOS
• Use third-party software such as DiscWizard™ or Disk Manager
• Use a third-party host adapter
For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available
LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. The ATA Set Features subcommand “F1H Report Full Capacity Available” causes Identify Data words 60 and 61 to report the full capacity.
See Section 4.1.3 on page 36 for more details on the Set Features command.
DB35 Series 7200.2 Product Manual, Rev. D
25
Windows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacities
greater than 32 Gbytes.
3.3.4
Ultra ATA/100 cable
An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4 and mode 5. This cable uses evennumbered conductors connected to the ground pins to improve signal integrity.
Master
Slave
Figure 5
Note.
3.4
Pin 1
Note. If you are using a 40-pin, 80-conductor
cable, attach the blue connector to the
motherboard, the black connector to the
master drive, and the gray connector
to the slave.
Co
Mo mpu
the ter
rbo
ard
Ultra ATA cable connectors
The drive supports both host and drive cable detection. The host detects the 80-conductor cable by
sampling pin 34, CBLID–, on the interface bus. The drive detects the 80-conductor cable by sensing a capacitor at the host side through the CBLID– signal. The result is reported in a Fast Rise
Detected bit (bit 13 of word 93 in the Identify drive parameter block).
Drive mounting
You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the
bottom-mounting holes. See Figure 6 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
• Use only 6-32 UNC mounting screws.
• Do not overtighten the mounting screws (maximum torque: 6 inch-lb.).
• Do not use a drive interface cable that is more than 18 inches long.
26
DB35 Series 7200.2 Product Manual, Rev. D
Notes:
1. Dimensions are shown in inches (mm).
2 Dimensions per SFF-8301 specification.
0.228
(5.79)
1.028 max
(26.11)
2.83
(71.80)
3 x 0.25 0.010
(6.35 0.037)
both sides
1.122 0.02
(28.5 0.51)
1.638
(41.61
0.01
0.25)
0.178
(4.27)
2.23
(56.56)
3.71
(94.35)
2
1.625 0.020
(41.28 0.51)
5.787 max
(146.99)
1.75 0.01
(44.45 0.25)
4.0 0.01
(101.60 0.25)
4 x 6-32 UNC-2B
0.150 (3.81) max. fastener
penetration. 3 threads
minimum engagement.
Recommended
case temperature
measurement location
3 x 6-32 UNC-2B
0.150 (3.81) max. fastener
penetration both sides. 3 threads
minimum engagement.
0.1240 0.01
(3.18 0.25)
3.750
(95.25
0.01
0.25)
Recommended
case temperature
measurement location
4.0 0.01
(101.60 0.25)
Figure 6
Mounting dimensions—top, side and end view
DB35 Series 7200.2 Product Manual, Rev. D
27
28
DB35 Series 7200.2 Product Manual, Rev. D
4.0
ATA interface
These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports
ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The
drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.
You can use a daisy-chain cable to connect two drives to a single AT host bus. For detailed information about
the ATA interface, refer to the draft of AT Attachment with Packet Interface Extension (ATA/ATAPI-7), NCITS
T13 1410D, subsequently referred to as the Draft ATA-7 Standard.
4.1
ATA interface signals and connector pins
Figure 7 summarizes the signals on the ATA interface connector that the drive supports. For a detailed description of these signals, refer to the Draft ATA-7 Standard.
Drive pin #
Signal name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Reset–
Ground
DD7
DD8
DD6
DD9
DD5
DD10
DD4
DD11
DD3
DD12
DD2
DD13
DD1
DD14
DD0
DD15
Ground
(removed)
DMARQ
Ground
DIOW–
STOP
Ground
DIOR–
HDMARDY–
HSTROBE
Ground
IORDY
DDMARDY–
DSTROBE
CSEL
DMACK–
Ground
INTRQ
IOCS16–
DA1
PDIAG–
CBLID–
DA0
DA2
CS0–
CS1–
DASP–
Ground
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Host pin # and signal description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Hardware Reset
Ground
Host Data Bus Bit 7
Host Data Bus Bit 8
Host Data Bus Bit 6
Host Data Bus Bit 9
Host Data Bus Bit 5
Host Data Bus Bit 10
Host Data Bus Bit 4
Host Data Bus Bit 11
Host Data Bus Bit 3
Host Data Bus Bit 12
Host Data Bus Bit 2
Host Data Bus Bit 13
Host Data Bus Bit 1
Host Data Bus Bit 14
Host Data Bus Bit 0
Device Data (15:0)
Ground
(No Pin)
DMA Request
Ground
Device I/O Write:
Stop Ultra DMA Burst
Ground
Device I/O Read:
Host Ultra DMA Ready:
Host Ultra DMA Data Strobe
Ground
I/O Channel Ready
Device Ultra DMA Ready
Device Ulta DMA Data Strobe
Cable Select
DMA Acknowledge
Ground
Device Interrupt
Reserved
Host Address Bus Bit 1
Passed Diagnostics
Cable Assembly Type Identifier
Device Address (2:0)
Device Address (2:0)
Chip Select (1:0)
Chip Select (1:0)
Drive Active/Slave Present
Ground
Pins 28, 34 and 39 are used for master-slave communication (details shown below).
Drive 1 (slave)
28
34
39
Figure 7
Drive 0 (master)
28
34
39
CSEL
PDIAG–
DASP–
Host
28
34
39
I/O pins and supported ATA signals
DB35 Series 7200.2 Product Manual, Rev. D
29
4.1.1
Supported ATA commands
The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA
commands, refer to the Draft ATA-7 Standard. See “S.M.A.R.T. commands” on page 37 for details and subcommands used in the S.M.A.R.T. implementation.
Table 6:
Supported ATA commands
Command name
Command code (in hex)
Check Power Mode
98H or E5H
Device Configuration Freeze Lock
B1H / C1H
Device Configuration Identify
B1H / C2H
Device Configuration Restore
B1H / C0H
Device Configuration Set
B1H / C3H
Device Reset
08H
Download Microcode
92H
Execute Device Diagnostics
90H
Flush Cache
E7H
Flush Cache Extended
EAH
Format Track
50H
Identify Device
ECH
Idle
97H or E3H
Idle Immediate
95H or E1H
Initialize Device Parameters
91H
Read Buffer
E4H
Read DMA
C8H
Read DMA Extended
25H
Read DMA Without Retries
C9H
Read Log Ext
2FH
Read Multiple
C4H
Read Multiple Extended
29H
Read Native Max Address
F8H
Read Native Max Address Extended
27H
Read Sectors
20H
Read Sectors Extended
24H
Read Sectors Without Retries
21H
Read Verify Sectors
40H
Read Verify Sectors Extended
42H
Read Verify Sectors Without Retries
41H
Recalibrate
10H
30
DB35 Series 7200.2 Product Manual, Rev. D
Command name
Command code (in hex)
Security Disable Password
F6H
Security Erase Prepare
F3H
Security Erase Unit
F4H
Security Freeze
F5H
Security Set Password
F1H
Security Unlock
F2H
Seek
70H
Set Features
EFH
Set Max Address
F9H
Note: Individual Set Max Address
commands are identified by the value
placed in the Set Max Features register as defined to the right.
Address:
Password:
Lock:
Unlock:
Freeze Lock:
Set Max Address Extended
37H
Set Multiple Mode
C6H
Sleep
99H or E6H
S.M.A.R.T. Disable Operations
B0H / D9H
S.M.A.R.T. Enable/Disable Autosave
B0H / D2H
S.M.A.R.T. Enable Operations
B0H / D8H
S.M.A.R.T. Execute Offline
B0H / D4H
S.M.A.R.T. Read Attribute Thresholds
B0H / D1H
S.M.A.R.T. Read Data
B0H / D0H
S.M.A.R.T. Read Log Sector
B0H / D5H
S.M.A.R.T. Return Status
B0H / DAH
S.M.A.R.T. Save Attribute Values
B0H / D3H
S.M.A.R.T. Write Log Sector
B0H / D6H
Standby
96H or E2H
Standby Immediate
94H or E0H
Write Buffer
E8H
Write DMA
CAH
Write DMA Extended
35H
Write DMA Without Retries
CBH
Write Log Extended
3FH
Write Multiple
C5H
Write Multiple Extended
39H
Write Sectors
30H
DB35 Series 7200.2 Product Manual, Rev. D
00H
01H
02H
03H
04H
31
Command name
Command code (in hex)
Write Sectors Without Retries
31H
Write Sectors Extended
34H
32
DB35 Series 7200.2 Product Manual, Rev. D
4.1.2
Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following
power up. The data is organized as a single 512-byte block of data, whose contents are shown in the Table 6
on page 30. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or
vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
The following commands contain drive-specific features that may not be included in the Draft ATA-7 Standard.
Word
Description
Value
0C5AH
0
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
1
Number of logical cylinders
16,383
2
ATA-reserved
0000H
3
Number of logical heads
16
4
Retired
0000H
5
Retired
0000H
6
Number of logical sectors per logical track: 63
003FH
7–9
Retired
0000H
10–19
Serial number: (20 ASCII characters, 0000H = none)
ASCII
20
Retired
0000H
21
Retired
0400H
22
Obsolete
0000H
23–26
Firmware revision (8 ASCII character string, padded with blanks to
end of string)
x.xx
27–46
Drive model number
(40 ASCII characters, padded with blanks to end of string)
ST3500841ACE
ST3400833ACE
ST3300822ACE
ST3250824ACE
ST3200827ACE
ST3160212ACE
ST3120213ACE
ST3802110ACE
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write
multiple (16)
8010H
48
Reserved
0000H
49
Standard Standby timer, IORDY supported and may be disabled
2F00H
50
ATA-reserved
0000H
51
PIO data-transfer cycle timing mode
0200H
52
Retired
0200H
53
Words 54–58, 64–70 and 88 are valid
0007H
54
Number of current logical cylinders
xxxxH
55
Number of current logical heads
xxxxH
DB35 Series 7200.2 Product Manual, Rev. D
33
Word
Description
Value
56
Number of current logical sectors per logical track
xxxxH
57–58
Current capacity in sectors
xxxxH
59
Number of sectors transferred during a Read Multiple or Write Multiple command
xxxxH
60–61
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
*Note: The maximum value allowed in this field is: 0FFFFFFFh
(268,435,455 sectors, 137 Gbytes). Drives with capacities over 137
Gbytes will have 0FFFFFFFh in this field and the actual number of
user-addressable LBAs specified in words 100-103. This is required
for drives that support the 48-bit addressing feature.
ST3500841ACE = 0FFFFFFFh*
ST3400833ACE = 0FFFFFFFh*
ST3300822ACE = 0FFFFFFFh*
ST3250824ACE = 0FFFFFFFh*
ST3200827ACE = 0FFFFFFFh*
ST3160212ACE = 0FFFFFFFh*
ST3120213ACE = DF94BB0h*
ST3802110ACE = 950F8B0h*
62
Retired
0000H
63
Multiword DMA active and modes supported
(see note following this table)
xx07H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003H
65
Minimum multiword DMA transfer cycle time per word (120 nsec)
0078H
66
Recommended multiword DMA transfer cycle time per word (120
nsec)
0078H
67
Minimum PIO cycle time without IORDY flow control (240 nsec)
00F0H
68
Minimum PIO cycle time with IORDY flow control (120 nsec)
0078H
69–74
ATA-reserved
0000H
75
Queue depth
0000H
76–79
SATA-reserved
xxxxH
80
Major version number
007EH
81
Minor version number
0000H
82
Command sets supported
346BH
83
Command sets supported
7D01H
84
Command sets support extension
4003H
85
Command sets enabled
34xxH
86
Command sets enabled
3xxxH
87
Command sets enable extension
4003H
88
Ultra DMA support and current mode
(see note following this table)
xx3FH
89
Security erase time
0000H
90
Enhanced security erase time
0000H
92
Master password revision code
FFFEH
93
Hardware reset value (see description following this table)
xxxxH
95–99
ATA-reserved
0000H
34
DB35 Series 7200.2 Product Manual, Rev. D
Word
Description
Value
100–103
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
These words are required for drives that support the 48-bit addressing
feature. Maximum value: 0000FFFFFFFFFFFFh.
ST3500841ACE = 976,773,168
ST3400833ACE = 781,422,768
ST3300822ACE = 586,072,368
ST3250824ACE = 488,397,168
ST3200827ACE = 390,721,968
ST3160212ACE = 312,581,808
ST3120213ACE = 234,441,648
ST3802110ACE = 156,301,488
104–127
ATA-reserved
0000H
128
Security status
0001H
129–159
Seagate-reserved
xxxxH
160–254
ATA-reserved
0000H
255
Integrity word
xxA5H
Note.
Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported
Note.
See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:
Description (if bit is set to 1)
Bit
Word 63
0
Multiword DMA mode 0 is supported.
1
Multiword DMA mode 1 is supported.
2
Multiword DMA mode 2 is supported.
8
Multiword DMA mode 0 is currently active.
9
Multiword DMA mode 1 is currently active.
10
Multiword DMA mode 2 is currently active.
Bit
Word 88
0
Ultra DMA mode 0 is supported.
1
Ultra DMA mode 1 is supported.
2
Ultra DMA mode 2 is supported.
3
Ultra DMA mode 3 is supported.
4
Ultra DMA mode 4 is supported.
8
Ultra DMA mode 0 is currently active.
9
Ultra DMA mode 1 is currently active.
10
Ultra DMA mode 2 is currently active.
11
Ultra DMA mode 3 is currently active.
12
Ultra DMA mode 4 is currently active.
13
Ultra DMA mode 5 is currently active.
Bit
Word 93
13
1 = 80-conductor cable detected, CBLID above VIH
0 = 40-conductor cable detected, CBLID below VIL
DB35 Series 7200.2 Product Manual, Rev. D
35
4.1.3
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the
Features register are defined as follows:
02H
Enable write cache (default).
03H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00H
Set PIO mode to default (PIO mode 2).
01H
Set PIO mode to default and disable IORDY (PIO mode 2).
08H
PIO mode 0
09H
PIO mode 1
0AH
PIO mode 2
0BH
PIO mode 3
0CH
PIO mode 4 (default)
20H
Multiword DMA mode 0
21H
Multiword DMA mode 1
22H
Multiword DMA mode 2
40H
Ultra DMA mode 0
41H
Ultra DMA mode 1
42H
Ultra DMA mode 2
43H
Ultra DMA mode 3
44H
Ultra DMA mode 4
45H
Ultra DMA mode 5
55H
Disable read look-ahead (read cache) feature.
82H
Disable write cache.
AAH
Enable read look-ahead (read cache) feature (default).
F1H
Report full capacity available
Note.
36
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
DB35 Series 7200.2 Product Manual, Rev. D
4.1.4
S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
commands and implementation, see the Draft ATA-7 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:
http://seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the
drive uses.
Code in features
register
S.M.A.R.T. command
D0H
S.M.A.R.T. Read Data
D1H
Vendor-specific
D2H
S.M.A.R.T. Enable/Disable Attribute Autosave
D3H
S.M.A.R.T. Save Attribute Values
D4H
S.M.A.R.T. Execute Off-line Immediate (runs DST)
D5H
S.M.A.R.T. Read Log Sector
D6H
S.M.A.R.T. Write Log Sector
D7H
Vendor-specific
D8H
S.M.A.R.T. Enable Operations
D9H
S.M.A.R.T. Disable Operations
DAH
S.M.A.R.T. Return Status
Note.
If an appropriate code is not written to the Features Register, the command is aborted and 0x 04
(abort) is written to the Error register.
DB35 Series 7200.2 Product Manual, Rev. D
37
38
DB35 Series 7200.2 Product Manual, Rev. D
5.0
Seagate Technology support services
Internet
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is
available 24 hours daily by email for your questions.
Presales Support:
Presales@Seagate.com
Technical Support:
DiscSupport@Seagate.com
Warranty Support:
http://www.seagate.com/support/service/index.html
mySeagate
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides
self-service access to critical applications, personalized content and the tools that allow our partners to
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,
password-protected Web interface-anytime, anywhere in the world.
spp.seagate.com
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You
may register for customized communications that are not available on the web. These communications contain
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.
Seagate Service Centers
Presales Support
Our Presales Support staff can help you determine which Seagate products are best suited for your specific
application or computer system, as well as product availability and compatibility.
Technical Support
Seagate technical support is available to assist you online at support.seagate.com or through one of our call
centers. Have your system configuration information and your “ST” model number available.
SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or
comments 24 hours daily and exchange messages with a technical support specialist during normal business
hours for the call center in your region.
DB35 Series 7200.2 Product Manual, Rev. D
39
Customer Service Operations
Warranty Service
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct
customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate
warranty service for assistance. Have your serial number and model or part number available.
Data Recovery Services
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery
services labs are currently located throughout the world. . Additional information, including an online request
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx
Authorized Service Centers
Seagate Service Centers are available on a global basis for the return of defective products. Contact your
customer support representative for the location nearest you.
USA/Canada/Latin America support services
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.
Global Customer Support
Presales, Technical, and Warranty Support
Call Center
Toll-free
USA, Canada,
and Mexico
1-800-SEAGATE
Data Recovery Services
Call Center
USA, Canada,
and Mexico
Toll-free
1-800-475-01435
Direct dial
+1-405-324-4700
Direct dial
+1-905-474-2162
FAX
1-800-475-0158
+1-905-474-2459
Europe, the Middle East and Africa Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.
Asia/Pacific Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,
go to the "Contact Us" page on www.seagate.com.
40
DB35 Series 7200.2 Product Manual, Rev. D
Index
Numerics
3D Defense System 1
A
acoustics 17
Active mode 15
agency certification (regulatory) 19
alternate capacity jumper 25
altitude 16
ambient conditions 3
ambient temperature 12, 16
areal density 10
ATA interface 29
ATA-standard commands 30
Australian C-Tick 19
autodetection 1
average seek time 12
B
BIOS 25
BPI 10
breather filter hole precautions 24
buffer 11
burst 1
C
cable 26
cable select 1
cable-select option 25
cache 1, 11
case temperature 16
CE mark 19
certification 19
Check Power Mode 30
chemical substances 20
commands 30
compliance 19
conducted noise 14
conducted RF immunity 18
configuring the drive 23
connector pins 29
connectors 26
contact start-stop cycles 18
Corrosive environment 21
CSA C22.2 (950) 19
CSEL 25
C-Tick 19
current profile 14
cycles 18
Cylinders 10
DB35 Series 7200.2 Product Manual, Rev. D
D
Data Defense 1
data-transfer rates 1
DC power 13
Default logical geometry 10
density 10
Device Configuration Freeze Lock 30
Device Configuration Identify 30
Device Configuration Restore 30
Device Configuration Set 30
Device Reset 30
Diagnostic Defense 1
diagnostic software 1, 37
DiscWizard 25
Disk Manager 25
dissipation 13
Download Microcode 30
Drive Defense 1
drive diagnostics 12
drive monitoring 1
drive self-test 1, 37
DST 37
E
electrical fast transient 18
electromagnetic compatibility 19
Electromagnetic Compatibility Directive 19
electromagnetic immunity 18
electrostatic discharge 18
EMC compliance 19
EN 60950 19
enclosures 20
Environmental protection 20
environmental specifications 16
EPRML 10
error-correction algorithms 1
errors 18
European Union 19
European Union Restriction of Hazardous Substances 20
Execute Device Diagnostics 30
F
failure prediction 37
FCC verification 20
Features register 36
Flush Cache 30
Flush Cache Extended 30
Format Track 30
formatted capacity 10
frequency 18
41
G
N
geometry 10
guaranteed sectors 10
noise 14
nominal power 3
nonoperating shock 17
nonoperating vibration 17
nonrecoverable read errors 18
H
handling 23
heads 1, 10
height 12
humidity 16
I
I/O data-transfer rate 11
Identify Device 30
Identify Device command 33
Idle 13, 30
Idle and Standby timers 15
Idle Immediate 30
Idle mode 15
Idle mode power 13
IEC950 19
Information Technology Equipment 19
Initialize Device Parameters 30
interface 10, 29
interface signals 29
interference 20
internal data-transfer rate OD 11
ISO document 7779 17
O
operating 13
operating power and current 13
operating shock 16
operating vibration 17
orientation 26
P
physical characteristics 12
pins 29
PIO 29
power consumption 13
power dissipation 13
power management 15
power specifications 13
power-management modes 15
Power-on to Ready 12
precautions 26
preventive maintenance 18
programmable power management 15
J
R
jumper settings 25
radiated RF immunity 18
radio and television interference 20
radio frequency 18
random track location 13
Read Buffer 30
Read DMA 30
Read DMA Extended 30
Read DMA without Retries 30
read errors 18
Read Log Ext 30
Read Multiple 1, 30
Read Multiple Extended 30
Read Native Max Address 30
Read Native Max Address Extended 30
Read Sectors 30
Read Sectors Extended 30
Read Sectors Without Retries 30
Read Verify Sectors 30
Read Verify Sectors Extended 30
Read Verify Sectors Without Retries 30
Read/write heads 10
Recalibrate 30
recording and interface technology 10
recording density 10
K
Korean RRL 19
L
LBA mode 10
length 12
logical geometry 10
M
maintenance 18
master 25
master/slave 1
Master/slave configuration 25
maximum temperature 16
measurement locations 16
modes 29
monitoring 1
mounting the drive 23, 26
42
DB35 Series 7200.2 Product Manual, Rev. D
recording heads 1
recording method 10
register 36
relative humidity 16
reliability 18
resistance 14
resistive load 14
RF 18
RoHS 20
S
S.M.A.R.T. commands 37
S.M.A.R.T. Disable Operations 31
S.M.A.R.T. drive monitoring 1
S.M.A.R.T. Enable Operations 31
S.M.A.R.T. Enable/Disable Autosave 31
S.M.A.R.T. Execute Offline 31
S.M.A.R.T. Read Attribute Thresholds 31
S.M.A.R.T. Read Data 31
S.M.A.R.T. Read Log Sector 31
S.M.A.R.T. Return Status 31
S.M.A.R.T. Save Attribute Values 31
S.M.A.R.T. Write Log sector 31
safety certification 19
screws 26
SeaTools 1, 37
sectors 10
Sectors per track 10
Security Disable Password 31
Security Erase Prepare 31
Security Erase Unit 31
Security Freeze 31
Security Set Password 31
Security Unlock 31
Seek 31
seek mode 13
seek time 12
Seeking 13
servo electronics 13
Set Features 31
Set Features command 36
Set Max Address 31
Set Max Address Extended 31
Set Multiple Mode 31
shock 16
signals 29
single-track seeks 12
slave 25
Sleep 13, 31
Sleep mode 15
sound 17
specifications 3
spindle speed 11
Spinup 13
spinup power 13
DB35 Series 7200.2 Product Manual, Rev. D
Standby 13, 31
Standby Immediate 31
Standby mode 13, 15
Standby to Ready 12
start/stop times 12
start-stop cycles 18
static-discharge precautions 23
stop times 12
subassembly 20
support services 39
surge immunity 18
T
technical support services 39
temperature 16
temperature gradient 16
timers 15
TMR 1
track density 10
track-to-track seek time 12
TUV North America 19
U
UL 1950 19
Ultra ATA/100 26
Ultra DMA 26
V
vibration 17
voltage 14
voltage dips, interrupts 18
voltage tolerance 14
W
weight 12
wet bulb temperature 16
width 12
Write Buffer 31
Write DMA 31
Write DMA Extended 31
Write DMA Without Retries 31
Write Log Extended 31
Write Multiple 1, 31
Write Multiple Extended 31
Write Sectors 31
Write Sectors Extended 32
Write Sectors Without Retries 32
43
44
DB35 Series 7200.2 Product Manual, Rev. D
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100389999, Rev. D, Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising